LTE Radio Access, Rel. RL25TD, Operating Documentation, Issue 02, Documentation Change Delivery 3
Creating TD-LTE Configurations DN09116085 Issue 02B Approval Date 2013-05-23 Confidential Nokia Siemens Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Siemens Networks for any additional information.
Creating TD-LTE Configurations
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2013. All rights reserved
f
Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.
The same text in German:
f
Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen. Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen. Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.
2
Id:0900d805809c738a Confidential
DN09116085
Creating TD-LTE Configurations
Table of contents This document has 28 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DN09116085
1 1.1 1.2 1.3
Flexi Multiradio BTS Flexi Multiradio BTS Flexi Multiradio BTS Flexi Multiradio BTS
modules used in configurations . . . . . . . . . . . . . . . System Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Radio Head (RRH) . . . . . . . . . . . . . . . . . .
2 2.1 2.1.1 2.1.2 2.1.3 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.2.8 2.2.9 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.4 2.4.1 2.4.2 2.4.3
TD-LTE configurations . . . . . . . . . . . . . . . . . . . . . . . . FZHA-only configurations . . . . . . . . . . . . . . . . . . . . . 1 L (BW 10MHz or 20MHz) with beamforming . . . . . 1+1 L (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . 1+1+1 L (BW 10MHz or 20MHz) with beamforming . FZNC-only configurations . . . . . . . . . . . . . . . . . . . . . 1 O (BW 10MHz or 20MHz) with beamforming . . . . . 1+1 O (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . 1+1+1 O (BW 10MHz or 20MHz) with beamforming . 1+1+1 M+N (BW 10MHz or 20MHz) . . . . . . . . . . . . . 1+1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . 1+1+1+1+1 A or I (BW 10MHz) . . . . . . . . . . . . . . . . . 1+1+1+1+1 A or I (BW 20MHz) . . . . . . . . . . . . . . . . . 1+1+1+1+1+1 A and I (BW 10MHz) . . . . . . . . . . . . . 1+1+1+1+1+1 A or I (BW 20MHz) . . . . . . . . . . . . . . . FZHA and FZNC configurations. . . . . . . . . . . . . . . . . 1 Omni A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . 1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . 1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . FZNI configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . 1+1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . 1+1+1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . .
Id:0900d805809c738a Confidential
...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ......
....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... .......
7 7 8 8
.. 9 .. 9 .. 9 . 10 . 11 . 12 . 12 . 13 . 14 . 15 . 16 . 17 . 18 . 19 . 20 . 21 . 21 . 22 . 23 . 24 . 25 . 26 . 27 . 27 . 27 . 28
3
Creating TD-LTE Configurations
List of figures Figure 1 Figure 2 Figure 3 Figure 4
4
Flexi Multiradio 10 BTS System Module . . . . . . . . . . . . . . . . . . . . . . . . . . 7 FZHA RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 FZNC RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 FZNI Remote Radio Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Id:0900d805809c738a Confidential
DN09116085
Creating TD-LTE Configurations
Summary of changes
Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Changes between issue 02A (2012-11-11, RL25TD) and issue 02B (2013-05-23, RL25TD). • •
FZNI layout has been added to Flexi Multiradio BTS modules used in configurations. FZNI configurations have been added.
Changes between issue 02 (2012-06-25, RL25TD) and issue 02A (2012-11-11, RL25TD). • • •
FBBA layout has been updated throughout the document. Configuration 1+1+1 A or I (BW 10MHz or 20MHz) using two RF Modules is also supported by FZNC. Information regarding needed FBBA modules in configuration 1+1+1 O (BW 10MHz or 20MHz) with beamforming has been corrected.
Changes between issue 01 (2012-03-22, RL15TD) and issue 02 (2012-06-25, RL25TD). • •
Section Flexi Multiradio BTS modules used in configurations has been updated. Section TD-LTE Configurations has been updated: – RL25TD-specific configurations have been added – RL15TD-specific configurations have been removed
Issue 01 (2012-03-22, RL15TD) is the first version of the document.
DN09116085
Id:0900d805809c7388 Confidential
5
Summary of changes
6
Creating TD-LTE Configurations
Id:0900d805809c7388 Confidential
DN09116085
Creating TD-LTE Configurations
Flexi Multiradio BTS modules used in configurations
1 Flexi Multiradio BTS modules used in configurations This section presents the following modules used in configurations: • •
Flexi Multiradio 10 BTS System Module (FSM) Flexi Multiradio BTS RF Modules
For information about cabling the modules, see Cabling Flexi Multiradio 10 BTS LTE. Pay attention to the order in which the cables are connected.
1.1
Flexi Multiradio BTS System Module Flexi Multiradio 10 BTS System Module (FSMF) is used. The indicated optical interfaces are crucial for configurations.
g
Note that: •
•
Flexi Baseband Module (FBBA) is optional, but needed in some configurations. In such cases, the FBBA need is stated. When using only one FBBA, install it in the left-hand side slot and connect it to BB EXT1 port on FSMF core. When using two FBBAs, connect the second one to BB EXT2. The EIF2/RF/6 interface can be used in two modes: as a transport interface or as a RP3-01 interface. The latter is for creating configurations.
EIF2/RF/6
RF/EXT1...3 BB EXT1 BB EXT2
RF/EXT BB EXT Figure 1
DN09116085
FBBA
RF/EXT BB EXT
Flexi Multiradio 10 BTS System Module
Id:0900d805809c7386 Confidential
7
Flexi Multiradio BTS modules used in configurations
1.2
Creating TD-LTE Configurations
Flexi Multiradio BTS RF Modules Flexi Multiradio BTS RF Modules FZHA and FZNC are used. ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
Figure 2
OPT 3 OPT 4
EAC
FZHA RF Module ANT1
ANT2
ANT3
DC IN OPT 1 OPT 2
Figure 3
OPT 3 OPT 4
EAC
FZNC RF Module
g
Note: Antenna numbers on the actual FZNC RF Module differ from those on Figure 3 FZNC RF Module. The actual antenna connectors (from left to right) are ANT1 to ANT8, although the FZNC is a six-pipe module. Thus, in the software implementation the connectors are presented in the same way as in the figure.
1.3
Flexi Multiradio BTS Remote Radio Head (RRH) Flexi Multiradio BTS RRHFZNI is used.
ANT3
ANT2 OPT2
Figure 4
8
ANT4
GPS
48V DC 20A MAX
OPT1
EAC
LMP
BF
ANT1
FZNI Remote Radio Head
Id:0900d805809c7386 Confidential
DN09116085
Creating TD-LTE Configurations
TD-LTE configurations
2 TD-LTE configurations 2.1 2.1.1
FZHA-only configurations 1 L (BW 10MHz or 20MHz) with beamforming
To antenna
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
9
TD-LTE configurations
2.1.2
Creating TD-LTE Configurations
1+1 L (BW 10MHz or 20MHz) This configuration requires one FBBA module.
Sector 2 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
DC IN OPT 1 OPT 2
10
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.1.3
TD-LTE configurations
1+1+1 L (BW 10MHz or 20MHz) with beamforming This configuration requires two FBBA modules.
To antenna
Sector 2 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
To antenna
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
To antenna
Sector 3 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
11
TD-LTE configurations
2.2 2.2.1
Creating TD-LTE Configurations
FZNC-only configurations 1 O (BW 10MHz or 20MHz) with beamforming
To antenna Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
12
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.2.2
TD-LTE configurations
1+1 O (BW 10MHz or 20MHz) Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 2 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
13
TD-LTE configurations
2.2.3
Creating TD-LTE Configurations
1+1+1 O (BW 10MHz or 20MHz) with beamforming This configuration requires one FBBA module.
Sector 2 ANT1
ANT2
ANT3
ANT4
ANT5
To antenna ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
To antenna ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 3 ANT1
ANT2
ANT3
ANT4
ANT5
To antenna ANT6 BF CAL
DC IN OPT 1 OPT 2
14
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.2.4
TD-LTE configurations
1+1+1 M+N (BW 10MHz or 20MHz) This configuration requires one FBBA module.
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 2 Sector 3 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
15
TD-LTE configurations
2.2.5
Creating TD-LTE Configurations
1+1+1+1 A or I (BW 10MHz or 20MHz) This configuration requires two FBBA modules.
Sector 1 ANT1
ANT2
Sector 2 ANT3
ANT4
ANT5
ANT6 BF CAL
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 3 ANT1
ANT2
Sector 4 ANT3
ANT4
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
For 10 MHz For 20 MHz
16
Id:0900d805809c736e Confidential
DN09116085
Creating TD-LTE Configurations
2.2.6
TD-LTE configurations
1+1+1+1+1 A or I (BW 10MHz) This configuration requires two FBBA modules.
Sector 1 ANT1
ANT2
Sector 2 ANT3
ANT4
Sector 3 ANT5
ANT6 BF CAL
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 4 ANT1
ANT2
Sector 5 ANT3
ANT4
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
17
TD-LTE configurations
2.2.7
Creating TD-LTE Configurations
1+1+1+1+1 A or I (BW 20MHz) This configuration requires two FBBA modules.
Sector 1 ANT1
ANT2
Sector 2 ANT3
ANT4
Sector 3 ANT5
ANT6 BF CAL
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 4 ANT1
ANT2
Sector 5 ANT3
ANT4
DC IN OPT 1 OPT 2
18
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.2.8
TD-LTE configurations
1+1+1+1+1+1 A and I (BW 10MHz) This configuration requires two FBBA modules.
Sector 1 ANT1
ANT2
Sector 2 ANT3
ANT4
Sector 3 ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 4 ANT1
ANT2
Sector 5 ANT3
ANT4
Sector 6 ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
19
TD-LTE configurations
2.2.9
Creating TD-LTE Configurations
1+1+1+1+1+1 A or I (BW 20MHz) This configuration requires two FBBA modules.
Sector 1 ANT1
ANT2
Sector 2 ANT3
ANT4
Sector 3 ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 4 ANT1
ANT2
Sector 5 ANT3
ANT4
Sector 6 ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
20
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.3
TD-LTE configurations
FZHA and FZNC configurations These configurations can be deployed on both FZHA and FZNC modules. Use the respective antenna connectors, that is: ANT1 to ANT6 on both modules.
2.3.1
1 Omni A or I (BW 10MHz or 20MHz)
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
21
TD-LTE configurations
2.3.2
Creating TD-LTE Configurations
1+1 A or I (BW 10MHz or 20MHz)
Sector 1
Sector 2
ANT1
ANT3
ANT2
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
22
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.3.3
TD-LTE configurations
1+1 A or I (BW 10MHz or 20MHz) Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6 BF CAL
ANT4
ANT5
ANT6 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 2 ANT1
ANT2
ANT3
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
23
TD-LTE configurations
2.3.4
Creating TD-LTE Configurations
1+1+1 A or I (BW 10MHz or 20MHz) This configuration requires one FBBA module.
Sector 1
Sector 2
ANT1
ANT3
ANT2
ANT4
Sector 3 ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
For 20MHz
24
Id:0900d805809c736e Confidential
DN09116085
Creating TD-LTE Configurations
2.3.5
TD-LTE configurations
1+1+1 A or I (BW 10MHz or 20MHz) This configuration requires one FBBA module.
Sector 1
Sector 2
ANT1
ANT3
ANT2
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 3 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
DN09116085
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
25
TD-LTE configurations
2.3.6
Creating TD-LTE Configurations
1+1+1 A or I (BW 10MHz or 20MHz) This configuration requires one FBBA module.
Sector 1 ANT1
ANT2
ANT3
ANT4
ANT5
ANT6
ANT7
ANT8 BF CAL
ANT6
ANT7
ANT8 BF CAL
ANT6
ANT7
ANT8 BF CAL
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 2 ANT1
ANT2
ANT3
ANT4
ANT5
DC IN OPT 1 OPT 2
OPT 3 OPT 4
EAC
Sector 3 ANT1
ANT2
ANT3
ANT4
ANT5
DC IN OPT 1 OPT 2
26
OPT 3 OPT 4
Id:0900d805809c736e Confidential
EAC
DN09116085
Creating TD-LTE Configurations
2.4 2.4.1
TD-LTE configurations
FZNI configurations 1 M (BW 10MHz or 20MHz)
Sector 1
ANT3
ANT2
LMP
OPT2
BF
1+1 M (BW 10MHz or 20MHz)
ANT3
ANT2
DN09116085
ANT4
ANT1
GPS
LMP
ANT3
ANT2 OPT1
OPT2
Id:0900d805809c736e Confidential
ANT4
GPS
EAC
OPT2
48V DC 20A MAX
OPT1
EAC
LMP
BF
ANT1
Sector 2
48V DC 20A MAX
Sector 1
BF
2.4.2
ANT4
GPS
EAC
OPT1
48V DC 20A MAX
ANT1
27
TD-LTE configurations
2.4.3
Creating TD-LTE Configurations
1+1+1 M (BW 10MHz or 20MHz) This configurations requires one FBBA module.
ANT4
ANT1
GPS
LMP
ANT3
ANT2 OPT1
OPT2
ANT4
GPS
EAC
48V DC 20A MAX
OPT2
BF
ANT3
ANT2 OPT1
EAC
LMP
BF
ANT1
Sector 2
48V DC 20A MAX
Sector 1
Sector 3
ANT3
ANT2 OPT2
28
Id:0900d805809c736e Confidential
ANT4
GPS
48V DC 20A MAX
OPT1
EAC
LMP
BF
ANT1
DN09116085
