BW211-212D-40 Operation Instruction E 04.2008 00815881.d08.pdf

Operating instructions Maintenance instructions

BW 211 / 212 / 213 D-40 BW 211 / 212 / 213 PD-40 S/N 101 582 42 . . . . S/N 101 582 43 . . . . S/N 101 582 44 . . . . S/N 861 583 00 . . . . S/N 101 582 47 . . . . S/N 101 582 48 . . . . S/N 101 582 49 . . . .

Single drum roller

Catalogue number

008 158 81

04/2008

Foreword

BOMAG machines are products from the wide range of BOMAG compaction equipment. F oreword

BOMAG’s vast experience in connection with state-of-the-art production and testing methods, such as lifetime tests of all important components and highest quality demands guarantee maximum reliability of your machine.

You should only operate the machine after you have been instructed and in compliance with these instructions. Strictly observe the safety regulations. Please observe also the guidelines of the Civil Engineering Liability Association ”Safety Rules for the Operation of Road Rollers and Soil Compactors” and all relevant accident prevention regulations.

This manual comprises: l

Safety regulations

l

Operating instructions

l

Maintenance instructions

l

Trouble shooting

For your own personal safety you should only use original spare parts from BOMAG. In the course of technical development we reserve the right for technical modifications without prior notification. These operating and maintenance instructions are also available in other languages.

Using these instructions will l

help you to become familiar with the machine.

l

avoid malfunctions caused by unprofessional operation.

Compliance with the maintenance instructions will l

enhance the reliability of the machine on construction sites,

l

prolong the lifetime of the machine,

l

reduce repair costs and downtimes.

Apart from that, the spare parts catalogue is available from your BOMAG dealer against the serial number of your machine. Your BOMAG dealer will also supply you with information about the correct use of our machines in soil and asphalt construction. The above notes do not constitute an extension of the warranty and liability conditions specified in the general terms of business of BOMAG GmbH. We wish you successful work with your BOMAG machine.

BOMAG GmbH will not assume liability for the function of the machine

BOMAG GmbH

l

if it is handled in a way not complying with the usual modes of use,

l

if it is used for purposes other than those mentioned in these instructions.

Printed in Germany Copyright by BOMAG

No warranty claims can be lodged in case of damage resulting from l

operating errors,

l

insufficient maintenance and

l

wrong fuels and lubricants.

Please note! This manual was written for operators and maintenance personnel on construction sites. Always keep this manual close at hand, e.g. in the tool compartment of the machine or in a specially provided container. These operating and maintenance instructions are part of the machine.

BW 211/212/213 D-40

BOMAG

3

Foreword

Please fill in ............................ Machine type (Fig. 1) ............................ Serial No. (Fig. 1 and 2) ............................ Engine type (Fig. 3) ............................ Engine No. (Fig. 3)

i

Note

Fig. 1

Fill in the above listed data when receiving the machine. Upon receipt of the machine our organization will instruct you about correct operation and maintenance. Please observe strictly all safety regulations and notes on potential dangers!

Fig. 2

Fig. 3

4

BOMAG

BW 211/212/213 D-40

Table of Contents

Technical Data Safety regulations Indicators and Controls

3.1 3.2 3.3 3.4

Operation

Maintenance

BW 211/212/213 D-40

7 15 23

General notes Description of indicators and control elements Display and control elements BTM Description of indicating and control elements BTM 3.5 Line diagram (EVIB) 3.6 Description of line diagram (EVIB) 3.7 Bar diagram (EVIB)

38 40 42 43

4.1 General notes 4.2 Tests before starting to operate 4.3 Disarming the anti-theft protection 4.4 Starting the engine 4.5 Starting with jump wires 4.6 Driving the machine 4.7 Switching the vibration on and off 4.8 Operating the parking brake, stopping the machine 4.9 Shutting the engine down 4.10 Emergency exit 4.11 Adjusting the steering wheel 4.12 Adjusting the seat 4.13 Operating the hood 4.14 Towing in case of an engine failure 4.15 Transport 4.16 BTM 05 settings before start-up 4.17 Measuring pass with BTM 4.18 Finishing compaction of a track 4.19 Printing measuring data after completing compaction 4.20 Changing the paper roll in the measuring value printer 4.21 Changing the printer ribbon in the measuring value printer

46 46 47 48 50 50 52 53 54 55 55 56 56 57 59 61 64 67 68 69 70

5.1 5.2 5.3 5.4 5.5 5.6 5.7

72 73 76 77 78 81 81

General notes on maintenance Fuels and lubricants Table of fuels and lubricants Running-in instructions Maintenance chart Check the engine oil level Check, clean the water separator BOMAG

26 26 36

45

71

5

Table of Contents

Trouble shooting

6

5.8 Checking the fuel level 82 5.9 Checking the hydraulic oil level 83 5.10 Checking the coolant level 83 5.11 Checking the dust separator on the oil bath air filter 84 5.12 Checking the tire pressure 85 5.13 Clean the cooling fins on engine and hydraulic oil cooler 85 5.14 Check the oil level in the drive axle 86 5.15 Checking the oil level in left/right wheel hubs 87 5.16 Checking the oil level in the vibration bearing housings 87 5.17 Changing engine oil and oil filter cartridges 89 5.18 Draining the fuel tank sludge 90 5.19 Service the battery 91 5.20 Check condition and tension of refrigerant compressor V-belt, replace the Vbelt 92 5.21 Service the air conditioning 93 5.22 Check, adjust the valve clearance 97 5.23 Checking / replacing the ribbed V-belt 99 5.24 Change the fuel filter cartridge 100 5.25 Change the fuel pre-filter cartridge 101 5.26 Check the engine mounts 102 5.27 Change the oil in the drive axle 103 5.28 Changing the oil in the wheel hubs 104 5.29 Changing the oil for the vibration bearings 105 5.30 Retighten the fastening of the axle on the frame 106 5.31 Tightening the wheel nuts 106 5.32 Checking the ROPS 107 5.33 Cleaning the oil bath air filter 107 5.34 Changing the hydraulic oil and the breather filter 109 5.35 Changing the hydraulic oil filter 110 5.36 Changing the coolant 111 5.37 Checking the injection valves 113 5.38 Cleaning, changing the dry air filter cartridge 115 5.39 Adjusting the scrapers 117 5.40 Adjusting the parking brake 118 5.41 Changing the tires 119 5.42 Changing the fresh air filter in the cabin 120 5.43 Tightening torques 120 5.44 Engine conservation 121 123

6.1 General notes 6.2 Engine

124 125

BOMAG

BW 211/212/213 D-40

1 Technical Data

BW 211/212/213 D-40

BOMAG

7

Technical Data

Fig. 4

Dimensions in mm

A

B

D

H

H2

K

L

O1

O2

S

W

BW 211 D-40

2960

2250

1500

2268

2972

490

5840

60

60

25

2130

BW 211 PD-40

2960

2250

1480

2268

2972

490

5840

60

60

25

2130

*

Weights Operating weight (CECE) with ROPS and cabin Axle load, drum (CECE) Rear axle load (CECE) Static linear load Travel characteristics Travel speed (1) Travel speed (2) Max. gradability (depending on soil) Engine Engine manufacturer Type Cooling Number of cylinders Rated power DIN ISO 3046 Rated speed Fuel

8

BW 211 D-40

BW 211 PD-40

kg

9500

10500

kg kg kg/cm

5750 3750 27

6750 3750 -

km/h km/h %

0 ... 6 0 ... 10 45

0 ... 6 0 ... 10 49

kW

Deutz BF4M 2012C Water 4 98


2300 Diesel

2300 Diesel

1 rpm

BOMAG

BW 211/212/213 D-40

Technical Data

*

BW 211 D-40 12 hydrostatic 2

BW 211 PD-40 12 hydrostatic 2

hydrostatic hydr.-mech.


Steering Type of steering Steering operation

articulated hydrostatic


Vibration Vibrating drum Drive system Frequency Amplitude

Hz mm

1 hydrostatic 30/36 1,8/0,9

1 hydrostatic 30/36 1,64/0,82

Tires Tire size Air pressure

bar

23.1-26/12 PR TL C7 1,4

23.1-26/12TL R1 1,4

Litres Litres Litres Litres

10 250 60 16

10 250 60 16

Electrical equipment Drive system Driven axles

V

Brakes Service brake Parking brake

Filling capacities Engine Fuel Hydraulic oil Coolant *

The right for technical modifications remains reserved

BW 211/212/213 D-40

BOMAG

9

Technical Data

Fig. 5

Dimensions in mm

A

B

D

H

H2

K

L

O1

O2

S

W

BW 212 D-40

2960

2250

1500

2268

2972

490

5840

60

60

25

2130

BW 212 PD-40

2960

2250

1480

2268

2972

490

5840

60

60

25

2130

*


10

BW 212 D-40

BW 212 PD-40

kg

10900

11350

kg kg kg/cm

7150 3750 33,6

7600 3750 -

km/h km/h %

0 ... 6 0 ... 10 45

0 ... 6 0 ... 10 49

kW



2300 Diesel

2300 Diesel

1 rpm

BOMAG

BW 211/212/213 D-40

Technical Data

*









Hz mm


1 hydrostatic 30/36 1,64/0,82


bar

23.1-26/12 PR TL C7 1,4

23.1-26/12TL R1 1,4


10 250 60 16

10 250 60 16


V




BW 211/212/213 D-40

BOMAG

11

Technical Data

Fig. 6

Dimensions in mm

A

B

D

H

H2

K

L

O1

O2

S

W

BW 213 D-40

2960

2250

1500

2268

2972

490

5840

60

60

35

2130

BW 213 PD-40

2960

2250

1480

2268

2972

490

5840

60

60

25

2130

*


12

BW 213 D-40

BW 213 PD-40

kg

12420

12870

kg kg kg/cm

7820 4600 36,7

8270 4600 -

km/h km/h %

0 ... 6 0 ... 10 45

0 ... 6 0 ... 10 49

kW



2300 Diesel

2300 Diesel

1 rpm

BOMAG

BW 211/212/213 D-40

Technical Data

*









Hz mm


1 hydrostatic 30/36 1,64/0,82


bar


V



23.1-26/12 PR TL C7 23.1-26/12TL R1 1,4

1,4

10 250 60 16

10 250 60 16



BW 211/212/213 D-40

BOMAG

13

Technical Data

14

BOMAG

BW 211/212/213 D-40

2 Safety regulations

BW 211/212/213 D-40

BOMAG

15

Safety regulations

General

Unintended use

This BOMAG machine is built in accordance with the latest technical standard and the valid technical rules and regulations. There is, however, a risk of danger for persons and property if:

Dangers may, however, arise from the machine if it is used by untrained personnel in an unprofessional way or if it is used for purposes other than those mentioned in these instructions.

l

the machine is used for purposes other than those it is intended for

Starting and operation of the machine in an explosive environment is prohibited.

l

the machine is operated by untrained personnel

l

the machine is modified or converted in an unprofessional way

l

the applicable safety regulations are not observed.

Each person involved in operation, maintenance and repair of the machine must therefore read and apply these safety regulations. This should be confirmed by obtaining the signatures of the customer, if necessary. Furthermore the following regulations and instructions are obviously also valid: l

applicable accident prevention instructions

l

generally acknowledged safety and road traffic regulations

l

country specific safety regulations. It is the duty of the operator to know and observe these regulations. This applies also for local regulations and the regulations for various types of manual work. If the recommendations in this manual differ from the regulations valid in your country, you must strictly observe the regulations in your country.

Intended use This machine must only be used for: l

compaction of bituminous materials, e.g. road surface layers. (AC and AD machines only)

l

medium and heavy compaction tasks in earth work (road sub-bases)

l

This machine must only be operated with fully functional safety equipment.

l

The machine should be checked by an expert once every year.

16

Do not work with vibration on hard concrete, on a cured concrete layer or heavily frozen ground.

Who is allowed to work with the machine? The machine must only be operated by trained and authorized persons which are at least 18 years of age. The responsibilities for the operation of the machine must be clearly specified and complied with. Persons under the influence of alcohol, medication or drugs must not operate, service or repair the machine. Maintenance and repair tasks require specific knowledge and must therefore only be carried out by trained and qualified personnel.

Conversions and alterations to the machine Unauthorized conversions to the machine are prohibited for safety reasons. Original parts and accessories have been specially designed for this machine. We wish to make expressly clear that we have not tested or authorized any original parts or special equipment not supplied by us. The installation and/or use of such products can impair the active and/or passive driving safety. The manufacturer expressly excludes any liability for damage resulting from the use of non-original parts or accessories.

Safety notes in the operating and maintenance instructions: Danger Sections marked like this point out possible dangers for persons. !

BOMAG

BW 211/212/213 D-40

Safety regulations

Caution Sections marked like this point out possible dangers for the machine or for parts of the machine. !

i

Note

Sections marked like this provide technical information concerning the optimal economical use of the machine.

Towing the machine Since the machine is not fitted with a towing hitch, the machine cannot be towed with a tow bar. If the machine has to be towed urgently out of the danger zone because of other risks, this must only be done on level ground or uphill using chains and ropes. For this purpose towing ropes of sufficient tensile strength must be fastened on the lifting eyes. After releasing the brake the machine can only be braked by the towing vehicle.

Environment Sections marked like this highlight activities for the safe and environmental disposal of fuels and lubricants as well as replaced parts.

Before releasing the brake block the machine with chocks to prevent unintended rolling.

Checking the Roll Over Protection Structure (ROPS)

Observe all environment protection regulations.

Information and safety stickers/decals on the machine Keep stickers/decals complete (see spare parts catalogue) and fully legible and observe their meaning.

i

Note

On machines with cabin the ROPS is an integral part of the cabin. The machine frame must not be distorted, bent or cracked in the area of the ROPS fastening points. The ROPS must not show any signs of corrosion, damage, hairline cracks or open fractures.

Replace damaged or illegible stickers/decals immediately.

Loading the machine Use only strong and stable loading ramps. The ramp inclination must be lower than the gradability of the machine. Secure the machine against turning over or slipping off.

The ROPS must not rattle about during driving. This would mean that it is not properly fastened. All bolted connections must be in accordance with the prescribed specifications and correctly tightened (observe the tightening torque values). Screws and nuts must not be damaged, bent or deformed. With the cabin installed check also the condition of the cabin mounts (rubber elements and screws).

Secure the machine on the transport vehicle against rolling off, slipping and turning over. Persons are highly endangered if l

they step or stand under loads being lifted

l

they remain in the drive range of the machine during a demonstration or during loading.

Neither must any additional parts be welded or bolted on, nor must any holes be drilled without the permission of the manufacturer, since this may impair the strength of the structure.

Starting the machine

The machine must not swing about when lifted off the ground.

Before starting

Use only safe lifting gear of sufficient load bearing capacity.

Operation of the machine is only permitted when sitting in the operator's seat.

Attach the lifting gear only to the specified lifting points.

Use only machines which have been properly serviced at regular intervals.

BW 211/212/213 D-40

BOMAG

17

Safety regulations

Become acquainted with the equipment, the control elements, the working mode of the machine and the area you will be working in.

Never start the engine by bridging the electrical connections on the starter, because the machine would probably start to move immediately.

Use your personal protective outfit (hard hat, safety boots etc.).

Starting in closed rooms

Check before mounting the machine if:

Exhaust gases are toxic! Always ensure an adequate supply of fresh air when starting in closed rooms!

l

there are persons or obstructions beside or under the machine

l

the machine is free of any oily and combustible material

Driving the machine

l

all handrails, steps and platforms are free of grease, oils, fuels, dirt, snow and ice

l

the engine compartment hood is closed and locked

If a machine has turned over and the cabin door is jammed, the right hand cabin window can be used as an escape door.

Persons in the danger area

Before taking up work, also after breaks, you should always convince yourself that the danger zone is free of persons or obstructions, especially when driving in reverse.

To climb onto the machine use steps and handrails. Check before starting, whether:

Give warning signals, if necessary. Stop work immediately if persons remain in the danger zone, despite the warning.

l

the machine shows any obvious defects

l

all protective devices are properly secured in their place

l

steering, brakes, control elements, lighting and warning horn are in order

Do not step or stand in the articulation area of the machine when the engine is running. Danger of squashing!

l

the seat is correctly adjusted

Driving

l

the mirrors (if available) are clean and correctly adjusted.

In events of emergency and in case of danger actuate the emergency stop switch immediately. Do not use the emergency stop switch as service brake.

Do not start the machine if any gauges, control lights or controls are defective.

Restart the machine only after the danger that caused the actuation of the emergency stop switch has been eliminated.

Do not take any loose objects with you or fasten them to the machine. On machines with ROPS you should always wear your seat belt!

If the machine has contacted high-voltage power lines:

Starting

l

do not leave the operator’s stand

Start and operate the machine only from the operator's seat

l

For starting set all control levers to "neutral position".

warn others from coming close to or touching the machine

l

Do not use any starting aids such as Start Pilot or ether.

if possible drive the machine out of the danger zone

l

have the power switched off

Operate the machine only from the operator’s stand.

After starting check all gauges. Starting with jump leads

Keep the cabin doors closed.

Connect plus with plus and minus with minus (ground cable) - always connect the ground cable last and disconnect it first! Wrong connections may cause severe damage in the electric system.

18

Do not adjust the driver’s seat while driving. Do not climb onto or off the machine while the machine is driving.

BOMAG

BW 211/212/213 D-40

Safety regulations

and the related risk of severe or even fatal accidents.

Change the travel direction only at standstill. Do not use the machine to transport persons. In case of unusual noises and development of smoke perform trouble shooting and have the fault corrected.

You should therefore always drive straight up or down a slope.

Always keep a sufficient distance to excavation walls and embankments and do not use working methods that could impair the stability of the machine.

Match the speed to the working conditions.

Do not work with vibration on hard concrete, cured bitumen layers or extremely frozen ground.

Keep away from edges and embankments.

Behaviour in traffic Always give way to loaded transport vehicles. Switch the lights on if the visibility is poor.

Always keep a sufficient distance when passing through subways, under bridges, tunnels, electric power lines etc.

Checking the effect of vibration

Driving on inclinations and slopes

When compacting with vibration you must check the effect on nearby buildings and underground supply lines (gas, water, sewage, electric power), if necessary stop compaction work with vibration.

Do not drive on gradients exceeding the maximum gradability of the machine.

Do not activate the vibration on hard (frozen, concrete) ground. Danger of bearing damage!

On slopes drive extremely careful and always directly up or down the slope. Change to a lower gear before starting to drive.

Parking the machine Park the machine on level and firm ground.

Wet and loose soils considerably reduce the ground adhesion of the machine on inclinations and slopes. Higher risk of accident!

Before leaving the machine:

Inclination

l

straighten the articulated joint to allow easy access to and from the machine.

l

return the travel lever to neutral position

l

apply the parking brake

l

shut the engine down and pull the ignition key out.

l

lock the cabin

l

secure the machine against unauthorized use.

Do not jump off the machine, use access steps and hand rails. Always secure parked machines, which could be in the way, with appropriate measures. Parking on slopes and gradients Fig. 7

The tipping angle was measured in static condition on level, hard ground with the machine stopped, no steering and without vibration.

Secure the machine against rolling, place metal chocks in front of and behind the drums.

Filling the fuel tank

With loose soil, acceleration/deceleration, running vibration, steering or attached accessoriies the tipping angle may be considerably lower.

Do not inhale fuel fumes.

Driving across slopes should therefore be strictly avoided, because of the high risk of tipping over

Do not refuel in closed rooms.

BW 211/212/213 D-40

Refuel only after shutting the engine and the auxiliary heater down. No open fire, do not smoke.

BOMAG

19

Safety regulations

Do not spill any fuel. Catch running out fuel, do not let it seep into the ground.

Catch running out hydraulic oil and dispose of environmentally.

Wipe off spilled fuel. Keep fuel free of dirt and water.

Always catch and dispose of biological hydraulic oils separately.

Leaking fuel tanks can cause explosions. Ensure tight fit of the fuel tank filling cover, replace it if necessary.

Do not start the engine after draining off the hydraulic oil.

Fire protection measures Make yourself acquainted with the location and the operation of fire extinguishers. Observe fire warning and fire fighting installations.

Maintenance

Once all work is completed (with the system depressurized!) check all connections and fittings for tight and leak-free fit. Changing hydraulic hoses All hydraulic hoses must be inspected visually at regular intervals. Hydraulic hoses must be changed immediately if:

Observe the maintenance tasks described in the operating and maintenance instructions, including the exchange of parts.

l

the outer layer is worn down to the metal lining (e.g. chafing, cuts, cracks)

l

embrittlement of the outer layer (development of cracks in the hose material)

l

deformation under pressurized and depressurized condition, which are not in accordance with the normal shape of the hydraulic hose

l

deformation in bends, e.g, squeezes, kinks, layer separation, formation of blisters

l

leakages.

l

non-observance of the installation requirements

Do not perform maintenance work with the machine driving or the engine running.

l

separation of the hydraulic hose from the fitting

Park the machine on horizontal, level and stable ground.

l

corrosion of the fitting, which impairs the function and the strength.

l

Do not mix up hoses by mistake.

l

damage or deformation of the fitting, which impairs the function and strength of the hose/ hose connection.

For service and repair work in the engine compartment support the engine compartment hood. Maintenance work must only be carried out by qualified and authorized personnel. When performing maintenance work above body height use the access steps on the machine or any other safe ladders and working platforms. Do not use machine parts as access steps. Keep unauthorized persons away from the machine.

Pull the key out of the ignition switch. Lock the articulated joint with the articulation lock. Working on hydraulic lines Always relieve the pressure in the hydraulic circuit before working on hydraulic lines. Hydraulic oil escaping under pressure may penetrate through the skin and cause severe injury. In case of being injured by hydraulic oil you should immediately seek medical advice, as otherwise this may lead to serious infections. When adjusting the hydraulic system do not stand behind or in front of the drum/wheels.

Working on the engine Shut the engine down before opening the engine compartment hood. Drain the engine oil at operating temperature danger of scalding!

Do not change the setting of high pressure relief valves. Drain hydraulic oil at operating temperature - danger of scalding!

20

Only genuine BOMAG hydraulic hoses ensure that the correct type of hose (pressure range) is used at the right place.

Wipe off spilled oil, catch running out oil and dispose of environmentally.

BOMAG

BW 211/212/213 D-40

Safety regulations

Store used filters and other oily materials in a separate, specially marked container and dispose of environmentally. Do not leave any tools or other objects, which could cause damage, in the engine compartment.

Catch running out fuel, do not let it seep into the ground and dispose of environmentally. Working on wheels and tires Explosion like bursting of tires and parts of rims and tires can cause severe or even deadly injuries.

Idle speed and full load speed must not be changed, since this would have a negative effect on the exhaust gas values and cause damage to engine and drive.

Assemble tires only with the appropriate knowledge and tools. If necessary have the tires assembled in a special workshop.

Turbo chargers work with high speeds and high temperatures. Keep hands, tools and materials away from the intake and outlet openings of the turbo charger and do not touch any hot surfaces.

Ensure correct tire pressure and do not exceed the highest specified pressure.

Check and replace the coolant only when the engine is cold. Catch running out coolant and dispose of environmentally. Working on electrical equipment Before working on electrical equipment disconnect the battery and cover it with insulating material. Do not use any fuses with higher ampere ratings or repair a fuse with a piece of wire. Fire hazard!

Check wheels and tires every day for specified pressure, cuts, bulges, damaged wheel rims, missing wheel studs and nuts. Do not drive with damaged tires or wheels. Anti-stick emulsions for tires must only be mixed using water and concentrated anti-stick agent according to the specifications of the manufacturer of the anti-stick agent. Observe the regulations for the protection of the environment. Cleaning Do not clean the machine while the engine is running.

Always disconnect the battery before starting to wled on the machine.

Do not use gasoline or other combustible substances for cleaning purposes.

Working on the battery When working on the battery do not smoke, do not use open fire. Do not let acid come in contact with skin and clothes. If being injured by acid flush off with clear water and seek for medical advice. Metal objects (e.g. tools, rings, wrist watches) must not contact the battery poles - danger of short circuit and burns!

When using steam cleaning equipment do not subject electrical components and insulating materials to the direct water jet, but cover them beforehand. l

Do not guide the water jet into the exhaust or into the air filter.

After maintenance work

When recharging maintenance free batteries remove the plugs to avoid the accumulation of explosive gases. When using an external battery to start the machine follow the respective instructions.

Reinstall all protective devices after completing the maintenance work.

Repair Attach a warning tag to the steering wheel if the machine is defective.

Dispose of old batteries environmentally.

Repairs must only be performed by qualified persons who have been instructed for this purpose. Use our repair instructions.

Switch the charging current off before removing the charge clamps. Ensure good ventilation, especially when charging the battery in a closed room. Working on the fuel system

No open fire, do not smoke, do not spill any fuel.

Exhaust gases are highly dangerous! Always ensure an adequate supply of fresh air when starting in closed rooms!

Do not inhale fuel fumes.

BW 211/212/213 D-40

BOMAG

21

Safety regulations

Test Depending on the type of application and the operating conditions vibratory equipment has to be examined by a specialist whenever required, but at least once every year.

22

BOMAG

BW 211/212/213 D-40

3 Indicators and Controls

BW 211/212/213 D-40

BOMAG

23

Indicators and Controls

Fig. 8

24

BOMAG

BW 211/212/213 D-40


1

Ignition switch

2

Instrument cluster

11 Rotary momentary contact switch for engine speed

3

Vent for heating and ventilation, driver

12 Rotary switch for direction indicators left/right*

4

Vent for heating and ventilation, footwell

13 Rotary switch for hazard light system 1

5

Push button vibration

14 Rotary switch for light system (StVZO)1

6

Travel lever

7

Rotary switch vibration, high/low frequency

8

Potentiometer for speed limitation control

9

Emergency stop push button

10 Push button for warning horn

BW 211/212/213 D-40

15 Rotary switch for working lights 1 16 Steering wheel adjustment lever

*

BOMAG

Optional equipment

25


3.1

General notes

3.2

Description of indicators and control elements

Please read this section thoroughly before operating this machine if you are not yet conversant with the indicators and control elements. All functions are described in detail hereunder. Paragraph 4 Operation contains only concise descriptions of the individual operating steps.

Fig. 9

No. 1 = Ignition switch Position "P"/"0" = ignition off, the key can be pulled out, engine not running. Position "I"

i

= ignition on, all control and warning lights on the fault monitoring board light up for a moment. The lighting can be switched on.

Note

The engine can only be started when the travel lever is in braking position. The ignition switch is provided with a lock against repetitive starting. To repeat the starting procedure you must first turn the ignition switch back to "0"-position. Position "II"

!

= turn further against spring pressure, the engine starts, return the ignition key to position "I" when the engine starts

Caution

Run the engine warm for a short while before starting to work. Do not let the engine run at idling speed for longer than 10 minutes. Do not shut the engine down all of a sudden from full speed, but let it idle for a while for temperature equalization.

26

BOMAG

BW 211/212/213 D-40


i yellow = Lights when the hydraulic oil filter is dirty, the warning buzzer sounds. The engine is shut down after 2 minutes. Check hydraulic system, replace hydraulic oil filter. j green

= Flashes when the direction indicator switch is actuated.

k red

= Lights when the parking brake is activated.

l

= Counts the operating hours while the engine is running. All maintenance work must be performed according to the indicated operating hours.

m

= Fuel tank filling level

Fig. 10

No. 2 = Instrument cluster

i

No. 3 = Vents for air conditioning, heating and ventilation, driver

Note

With the ignition switch in position I all gauges and instruments are switched on for 3 seconds.

No. 4 = Vents for air conditioning, heating and ventilation, footwell*

a yellow = Lights when there is water in the fuel prefilter. The warning buzzer sounds. Drain the water separator. b yellow = Lights when the air intake is pre-heated (cold start) c yellow = Lights when the driver's seat is not occupied. If the machine is travelling the warning buzzer will sound, engine is shut down after 4 seconds. d red

e red

= Lights in case of too low engine oil pressure. The warning buzzer sounds. Check engine oil level, repair the engine if necessary. = Lights in case of too low coolant level. The engine is shut down after 2 minutes. Fill up coolant. Seal leakages

f yellow = Lights if the battery is not being charged. Check V-belt, if necessary repair the generator.

Fig. 11

No. 5 = Push button for vibration l

Select or actuate the frequencies with the vibration selector switch.

l

Switch the vibration on or off by pressing the push button.

g yellow = Lights if the air filter cartridge is soiled. Clean or replace cartridge as necessary. h red

= Lights if engine overheats. The warning buzzer sounds. Switch off vibration, run engine with idle speed or shut down engine if necessary, clean engine oil cooler and radiator, if necessary repair engine. *

BW 211/212/213 D-40

BOMAG

Optional equipment

27


Fig. 12

Fig. 14

No. 6 = Travel lever

No. 8 = Rotary switch for speed range selection

Position "middle" = Braking position service brake Position "middle, right" = Parking brake, to start the engine Position "I"

= Forward travel

Position "II"

= Backwards travel

i

Position "turtle" = Working speed Position "rabbit"

= Transport speed

Note

If the engine speed drops under load when driving on steep gradients, take the travel lever slightly back towards neutral. This relieves the hydraulic system and reduces the load on the diesel engine.

Fig. 15

No. 9 = Emergency stop switch The engine will be shut down and the brake will close. Danger Danger of accident! !

Fig. 13

No. 7 = Rotary switch for vibration Position "Middle" = Vibration off

Operate only in emergency situations during operation, do not use as a service brake. The machine should only be started again after the danger, that caused the actuation of the emergency stop switch, has been removed. operate

Position "Right" = low amplitude, high frequency Position "Left" = high amplitude, low frequency

28

BOMAG

= push the button completely down, it will automatically lock in end position.

BW 211/212/213 D-40


unlock

= turn the button clockwise and release it.

to drive

= move the travel lever first to braking position, then start the engine and choose the travel direction.

Caution Always drive and vibrate with max. engine speed! Control the travel speed with the travel lever. !

For safety reasons the travel system of the machine will only be enabled after the travel lever has been shifted back to braking position.

Fig. 18

No. 12 = Rotary switch for direction indicators left / right* Position "middle" = Direction indicators disabled

Fig. 16

Position "left or right" = Front and rear direction indicators for the corresponding side of the machine light up, the control light in the instrument cluster flashes.

No. 10 = Push button for warning horn

Fig. 17

No. 11 = Rotary momentary contact switch for engine speed Electric engine speed adjustment Position left

Fig. 19

= Idle speed position

No. 13 = Rotary switch for hazard light system **

i

Note Position "left"

Normal position for engine start. Position right

= Full throttle position, operating position for driving and vibration

BW 211/212/213 D-40

* **

BOMAG

= Hazard light switched off, control lights off.

Optional equipment Optional equipment

29


Position "right" = Hazard light switched on, control light 1 in instrument cluster lights up.

Fig. 22

No. 16 = Lever, steering wheel adjustment Fig. 20

No. 14 = Rotary switch for light system (StVZO)* Position "left"

Danger Danger of accident! !

= Light off

Position "middle" = Sidelights on, with ignition switch in position "I" or "P"

Do not adjust the steering wheel while driving. pull up

= adjust height of steering wheel

press down

= adjust inclination of steering wheel

Position "right" = Travel light on, with ignition switch in position "I".

Fig. 23

No. 17 = 2-pole socket Fig. 21

No. 15 = Rotary switch for working Position "left"

lights**

Current only with the ignition switch in position "I" or when the engine is running.

= Light off

Position "right" = Working lights on, with ignition switch in position "I".

* **

30

Optional equipment Optional equipment

BOMAG

BW 211/212/213 D-40


Fig. 24

Fig. 25

No. 18 = Fuses in electric installation box

a = toggle switch for flashing beacon

F03, 15A

= Vibration

F05, 15A

= Socket

F07, 15A

= Hazard light*

F09, 10A

= Parking tail light, left*

F10, 10A

= Parking tail light, right*

F11, 15A

= Head lights, StVZO*

F13, 30A

= Starting

F14, 15A

= Engine solenoid

F18, 10A

= Working head lights, relay*

F19, 15A

= Working head lights, front, left*

F22, 15A

= Working head lights, rear*

F23, 10A

= Warning horn

F24, 10A

= Monitoring, gauges

F25, 10A

= Solenoid valve brake/travel

F39, 15A

= Cab*

F70, 15A

= Indicator*

F105, 20A

= Engine speed control

!

b = toggle switch for front windscreen wiper/ washer up

= windscreen wiper moves to end position and stops.

down

= Switches on wiping of front windscreen.

Push button

= Front windscreen is sprayed during wiping.

c = toggle switch for rear windscreen wiper/ washer up

= windscreen wiper moves to end position and stops.

down

= Switches on wiping of rear windscreen.

Push button

= Rear windscreen is sprayed during wiping.

d = toggle switch for rear windscreen heating

Danger

Fire hazard! Do not use fuses with higher ampere ratings and do not bridge fuses.

Fig. 26 *

Optional equipment

BW 211/212/213 D-40

No. 19 = Fuse box, cabin

BOMAG

31


i

Note

Danger Fire hazard!

The light goes out.

Do not use fuses with higher ampere ratings and do not bridge fuses.

g = Rotary switch for cabin heater (temperature selector switch)

(1), 15A = (F43) wiper/washer, rear

Position ’’Off“

(2), 15A = (F44) wiper/washer, front

Position blue range

!

(3), 10A = (F130) relay for rear windscreen heating, reading light

Position red range

(4), 25A = (F31) cabin fan (5), 10A = (F41) flashing beacon

= cabin heater switched off. = temperature selection for air conditioning. = Temperature selection for cabin heater.

(6), 15A = (F144) cab socket (7), 15A = (F143) rear windscreen heating (8), 5A

= (F42) potential 30, cab light

Fig. 28

No. 21 = Cabin light Fig. 27

No. 20 = Control panel for ventilator, air conditioning, heating e = Rotary switch for cabin ventilator Position ’’Off“

= cabin ventilator switched off.

Position 1, 2 and 3 = ventilator stages of different strengths f = Push button for air conditioning* press

i

= air conditioning switched on.

Note

The lights above the push buttons light up. With rotary switch (g) the air conditioning unit can be regulated within the blue range. press again *

32

= air conditioning switched off.

Optional equipment

BOMAG

BW 211/212/213 D-40


After the filter service reset the indicator to "zero" by pressing the push button.

i = reading and dashboard light j = toggle switch for reading and dashboard light k = toggle switch for cabin light l = cabin light

Fig. 31

No. 24 = Service indicator hydraulic oil filter

Fig. 29

No. 22 = Main fuse for battery 80A

=

l

Check the service indicator at operating temperature and with the engine running.

l

If necessary press the pin in.

Pin remains pressed in

(F00)

Pin pops out

i

Note

= hydraulic oil filter element o.k. = replace the hydraulic oil filter element

The main fuse is located in the battery compartment

Fig. 32

No. 25 = Fuel gauge shows the fuel level in the fuel tank.

Fig. 30

No. 23 = Air filter service indicator With the service indicator the real degree of filter contamination can even be checked when the engine is stopped. The filter must be service when the yellow piston reaches the inscription "Service" in front of the red background.

BW 211/212/213 D-40

BOMAG

33


Fig. 33

No. 26 = Anti-theft

Fig. 34

protection*

No. 27 = EVIBdisplay**

prevents unauthorized starting of the engine. Keypad = Input of user and service code (maintenance).

is a compaction measuring unit for continuous display of the load bearing characteristics (MN/m2) during the compacting pass. EVIB value

i

Note

Enter the user code with the ignition switched off! After entering the user code you should start the engine within 30 seconds.

Increase

= higher load bearing capacity

Constant

= end of compaction

i

Note

Modular upgrading to BTM plus / BTM prof and/or BCM 05 possible.

After entering the service code the anti-theft protection remains switched off. red LED display flashes slowly = anti-theft protection active. LED display lights green = every time a digit of the user or service code is entered.

i

Note

After shutting down the engine it can be restarted within a period of 12 seconds, in any other case the user code needs to be entered again.

*

34

Optional equipment

**

BOMAG

Optional equipment

BW 211/212/213 D-40


BW 211/212/213 D-40

BOMAG

35


3.3

*

Display and control elements BTM*

Optional equipment

Fig. 35

36

BOMAG

BW 211/212/213 D-40


1

EVIBdisplay

11 not used

2

Display for jump operation

12 not used

3

Push button F5 START

13 not used

4

Push button F6 STOP

14 not used

5

Push button F7 PRINT (only BTM prof)

15 not used

6

Push button F8 DELETE

16 not used

7

Vibration frequency display

17 Travel speed display

8

Rotary switch setting of nominal value

18 Amplitude display

9

Push button F14 nominal value increase

19 Printer for measuring values (only BTM prof)

10 Push button F13 nominal value decrease

BW 211/212/213 D-40

20 Fault light

BOMAG

37


3.4

i

To print out the measuring data saved during the last pass press button F7 PRINT.

Description of indicating and control elements BTM

short actuation = Line diagram long actuation ≥5 sec. = Bar chart Control field F7 goes out and the measuring value printer starts to print out measuring data.

Note

The BTM plus can be upgraded to BTM prof and/ or BCM 05.

i

Surface covering dynamic compaction control (SCCC) The BOMAG compaction measuring systems EVIB-meter (BEM) and Terrameter BTM plus/prof are integrated in the work process for continuous and surface covering evaluation of compaction and load bearing capacity of soils and non-bonded bearing courses.

No. 6 = Button F8 DELETE press

No. 7 = Frequency display with vibration switched on this instrument shows the frequency (rotating speed) of the exciter shaft.

No. 1 = EVIB-display Display of the dynamic soil stiffness in MN/m2.

No. 8 = Rotary switch P3 pre-setting of nominal values

No. 2 = Display for jump operation

red symbol

= All stored faults are deleted.

! Caution If the increase of the measuring value is to be calculated on a track press button F8 DELETE only when changing the track.

The EVIB-value, designated as vibration modulus, with the unit MN/m2 is directly linked with the deformation modules EV1 or EV2 known from the plate load test acc. to DIN 18134.

yellow symbol

Note

After the printing process has finished any amount of diagrams can be printed out by pressing the same button F7 (PRINT).

= Drum jumps

The desired maximum dynamic stiffness modulus EVIB [MN/m 2] can be pre-selected in 6 stages (45, 80, 100, 120,150 and Max.).

= Drum jumps excessively or tumbles

The selected value is shown on the screen in field „P3“

Select a smaller amplitude, if necessary!

No. 9 = Button F14 increase of nominal value

No. 3 = Button F5 START

With each actuation of the button the presetting is raised by one stage.

press

= Starts recording of measuring values

The selected value is shown on the screen in field „P3“

Control field "F5" flashes green on the screen.

No. 10 = Button F13 reduction of nominal value

No. 4 = Button F6 STOP press

= Stops recording of measuring values

With each actuation of the button the presetting is reduced by one stage.

The green control field "F7" PRINT on the screen lights up.

i

Note

Depending on the measuring result the green control field "F5" CONTINUE or the red control field "F6" FINISHED will light up. No. 5 = Button F 7 Print*

38

*

BOMAG

only with BTM prof

BW 211/212/213 D-40


The selected value is shown on the screen in field „P3“ No. 11 = Button F11 is not used No. 12 = Button F12 is not used No. 13 = Button F11 is not used No. 14 = Rotary switch P1 is not used No. 15 = Button F10 is not used No. 16 = Button F9 is not used No. 17 = Travel speed display Shows the travel speed of the machine. No. 18 = Amplitude display This gauge shows the current vertical amplitude of the machine. No. 19 = Printer for measuring values* To print out the measuring data saved during the last pass press button (7) "PRINT". No. 20 = Fault light Infor the BOMAG After Sales Service if it lights up.

BW 211/212/213 D-40

BOMAG

39


3.5 *

Line diagram* (EVIB)

only BTM prof

Fig. 36

40

BOMAG

BW 211/212/213 D-40


1

Pass-No.

2

Travel direction

11 EVIB-change 12 Medium frequency

3

Machine equipment (BTM 05/BTM-E)

13 Mean travel speed

4

Software status of the measuring equipment

14 Track length

5

Machine number

15 Raster division in longitudinal direction

6

Machine type

7

Amplitude

16 Marking (thick line) excessive jumping, tumbling of the drum

8

Maxiumum EVIB value

17 Longitudinal raster line

9

Miniumum EVIB value

18 Measuring value raster line

10 Mean EVIB-value

BW 211/212/213 D-40

19 Diagram line 20 Marking (thin line) jumping of the drum

BOMAG

41


3.6

Description of line diagram (EVIB)

Graduation of the measuring track (track length in printout) into fixed sections.

*

No. 16 = Marking of jump information Indicates excessive jumping/tumbling of the drum on the marked track section (thick line).

No. 1 = Pass Total number of measured passes on this track.

i

No. 2 = Travel direction

Note

Select a smaller amplitude, if necessary!

No. 3 = Machine equipment No. 4 = Software status of the measuring equipment

No. 17 = Longitudinal raster line

No. 5 = Machine number

No. 19 = Diagram line

No. 6 = Machine type

Shows the EVIB-value at any point of the rolled track. The raster line enables the location related assignment of the EVIB-value and the location of a fault (over or under compaction).

No. 18 = Measuring value raster line

No. 7 = Amplitude This gauge shows the vertical amplitude the machine has worked with on this track.

No. 20 = Marking of jump information

No. 8 = Maxiumum EVIB value

Indicates jumping of the drum on the marked track section (thin line).

No. 9 = Miniumum EVIB value No. 10 = Mean EVIB-value This gauge shows the vertical amplitude the machine is currently working with on this track. No. 11 = EVIB-change EVIB-change in %. This always refers to the previous pass in the same direction of travel. No. 12 = Medium frequency No. 13 = Mean travel speed shows the mean value of speed driven during this pass.

i

Note

Always shows the same travel speed in order to avoid a falsification of the measuring results. No. 14 = Track length Measured track length between START and STOP. No. 15 = Raster division in longitudinal direction Is used to pinpoint individual measuring values on the measuring curve.

i

Note

The raster lines mark measuring track sections of 5 m length. *

42

only BTM prof

BOMAG

BW 211/212/213 D-40


3.7

Bar diagram* (EVIB)

The bar diagram differs from the line diagram only by the graphic representation of measuring values. In the bar diagram the mean values of 5 m sections are shown as bars. In addition, the EVIB changes of the individual 5 m sections are specified in percent after the second pass in the same travel direction.

*

only BTM prof

BW 211/212/213 D-40

BOMAG

43


44

BOMAG

BW 211/212/213 D-40

4 Operation

BW 211/212/213 D-40

BOMAG

45

Operation

4.1

General notes

Please read section 3 Indicators and Control Elements thoroughly before operating the machine if you are not yet fully familiar with the indicators and control elements of the machine.

4.2

Tests before starting to operate

The following tests must be performed before each work day or before a longer work period.

All indicators and control elements are described in detail in this chapter.

!

Danger

Danger of accident! Please observe strictly the safety regulations in chapter 2 of these operating and maintenance instructions! Park the machine on level ground.

l

Check: l

Fuel tank and fuel lines for leaks

l

Bolted connections for tight fit

l

Function of the steering

l

Check the machine for cleanliness and damage

l

availability of the appropriate operating and maintenance instructions,

l

check if the machine has been properly serviced.

i

Note

For a description of the following work refer to the section "maintenance every 10 operating hours" engine oil level

l

i

Note

Hydraulic systems, which are filled with Panolin HLP Synth. 46, the same oil must be used for filling up. In case of any other ester based oil consult the lubrication service department of the respective oil manufacturer. l

Check the hydraulic oil level, top up if necessary.

l

Check the coolant level, top up if necessary.

!

Danger

Fire hazard! Do not refuel in closed rooms l

46

BOMAG

Check the fuel level, top up if necessary.

BW 211/212/213 D-40

Operation

Check water separator in the fuel system, drain if necessary.

l

l

Adjust the scrapers if necessary

l

Tire pressure. Pressure see technical data.

Caution Ensure equal pressure in both tires. !

4.3

Disarming the anti-theft* protection

Before starting the engine the anti-theft protection must be disarmed by entering a code while the ignition is still off. Caution If the anti-theft protection is disarmed with the ignition switched on, the diesel engine will run in limp home program! !

Fig. 37

i

Note

With the anti-theft protection armed light emitting diode a (Fig. 37) flashes slowly in red. Slowly enter the six-digit user code while the ignition is switched off.

l

i

Note

With each digit of the code the light emitting diode lights green. l

Press the confirmation key ’’VAL“.

l

The anti-theft protection is now disarmed and the engine must be started within the next 30 seconds.

i

Note

After the engine has been shut down restarting is possible within 12 seconds. After this the anti-theft protection will be armed again. The red LED flashes at intervals of one second. *

BW 211/212/213 D-40

BOMAG

Optional equipment

47

Operation

After entering the service code (for maintenance work) the anti-theft protection remains disarmed.

4.4 !

Starting the engine

Danger

Danger of accident! Always wear your seat belt.

Fig. 38 l

Check, whether the travel lever (Fig. 38) is engaged to the right in brake position.

Fig. 39 l

48

BOMAG

Turn the rotary vibration selector switch (Fig. 39) to position "0", vibration off.

BW 211/212/213 D-40

Operation

Fig. 40 l

Check, whether the emergency stop switch (Fig. 40) is unlocked.

Fig. 43

All control and warning lights (Fig. 43) in the fault monitoring board light up for a moment. The battery control (d) and brake warning lights (g) light up, the engine oil pressure warning light (b) flashes. ! Caution Perform the starting process for maximum 20 seconds without interruption and pause for a minute between starting attempts.

If the engine has not started after two attempts perform trouble shooting.

Fig. 41 l

Turn rotary switch (Fig. 41) to position "Min" (idle speed).

Fig. 44 l

Turn the ignition key to position "II" (Fig. 44), the starter will crank the engine.

l

As soon as the engine ignites return the ignition key to position "I".

Fig. 42 l

Turn the ignition key (Fig. 42) to position "I".

BW 211/212/213 D-40

Caution Do not allow the engine to run longer than 10 minutes with idle speed. !

BOMAG

49

Operation

4.5

Starting with jump wires

4.6 !

Driving the machine

Danger

Danger of accident! Wet and loose soils considerably reduce the ground adhesion of the machine on inclinations and slopes. Soil conditions and weather influences impair the gradability of the machine. Do not drive up and down inclinations exceeding the maximum gradability of the machine (see technical data). Do not drive without wearing your seat belt. Fig. 45

Always give way to loaded transport vehicles! Before starting to drive make sure that the drive range is absolutely safe.

Caution A wrong connection will cause severe damage in the electric system. !

l

Bridge the machine only with a 12 Volt auxiliary battery.

l

When jump starting with an external battery connect both plus poles first.

l

Then connect the ground cable first to the minus pole of the current supplying auxiliary battery and then to engine or chassis ground, as far away from the battery as possible (Fig. 45).

l

Start as described under 'Starting the engine'.

l

Once the engine is running switch on a powerful consumer (working light, etc.). !

Caution

If no powerful consumer is switched on voltage peaks may occur when separating the connecting cables between the batteries, which could damage electrical components. l

After starting disconnect the negative poles (ground cable) first and the positive poles after.

l

Switch off the consumer.

50

! Caution Always keep the cabin door closed while driving with the machine. With the door opened and the machine fully articulated extreme oscillations of the machine may damage the door.

i

Note

The machine is equipped with a seat contact switch (safety feature). If the driver gets up from his seat while driving, the signal horn is activated and the machine is slowed down to standstill after four seconds. When the driver sits down again the machine will continue the travel. Before resuming operation sit down on the seat, engage the travel lever in "0"-position (brake position), then operate the travel lever again to the desired travel direction.

BOMAG

BW 211/212/213 D-40

Operation

Fig. 46 l

Fig. 49

Close the cabin door (Fig. 46).

l

Select the desired travel speed range (Fig. 49).

Fig. 47 l

Sit on the driver's seat (Fig. 47) and fold down the armrest.

Fig. 50 l

Turn the rotary switch (Fig. 50) to "Max" position (full throttle).

Fig. 48 l

Fasten your seat belt (Fig. 48).

Fig. 51

"Start engine", see previous sections.

l

l

BW 211/212/213 D-40

BOMAG

Push the travel lever (Fig. 51) to the left out of braking position and move it slowly to the desired travel direction.

51

Operation

i

Note

Shift the travel lever out of "0"-position slowly to forward or reverse, the machine will drive forward or reverse at a speed which corresponds with the displacement of the travel lever. Returning the travel lever towards neutral will brake the machine and in "0"-position of the travel lever the machine will stop. Danger Danger of accident! !

When stopping on inclinations and slopes pull the travel lever to the right and lock it in braking position.

4.7

!

Switching the vibration on and off

Danger

Risk of damage! When compacting with vibration you must check the effect of nearby buildings and underground supply lines (gas, water, sewage, electric power), if necessary stop compaction with vibration. Do not activate the vibration on hard (frozen, concrete) ground. Danger of bearing damage!

Important notes on travel operation Caution When changing the travel direction hold the travel lever for a moment in "0"-position, until the machine has stopped, before actuating to the new travel direction. !

Do not operate jerkily! When driving up and down inclinations move the travel lever slowly back towards neutral to brake the machine. If the engine speed drops when driving up extreme inclinations move the ravel lever slightly back, if necessary change to the lower speed range.

Fig. 52 l

Switch to working speed (Fig. 52) (turtle).

Pre-selecting the vibration

Fig. 53 l

52

BOMAG

Pre-select amplitude/frequency with the rotary switch (Fig. 53).

BW 211/212/213 D-40

Operation

Switch the vibration on

4.8

Operating the parking brake, stopping the machine

Fig. 54

Turn the rotary switch (Fig. 54) to position "Max" (full throttle).

l

Fig. 56

Caution Switch the vibration on only at max. engine speed. !

Return the travel lever (Fig. 56) slowly to "neutral"-position and engage it to the right parking brake position.

l

The machine is automatically braked by the hydrostatic drive and parking brake closes.

i

Note

The parking brake also closes automatically when shutting the engine down.

Fig. 55 l

Press the push button (Fig. 55) in the travel lever while driving, the drum will vibrate.

Switching the vibration off l

Press the push button again and after work switch the rotary vibration switch to position "0".

BW 211/212/213 D-40

BOMAG

53

Operation

4.9

Shutting the engine down

! Caution Straighten the articulated joint to provide easier access to the machine.

Fig. 59

Turn the ignition switch (Fig. 59) to position "0" or "P" and pull the ignition key out.

l

i

Note

The parking brake closes automatically when shutting the engine down. Fig. 57

Return the travel lever (Fig. 57) slowly to "neutral"-position and engage it to the right in braking position.

l


Secure the machine against unauthorized use, pull the ignition key out, lock the cabin door.

Fig. 58

Turn rotary switch (Fig. 58) to position "Min" (idle speed).

l

i

Note

Do not shut the engine down all of the sudden from full speed, but let it idle for a while for temperature equalization.

54

BOMAG

BW 211/212/213 D-40

Operation

4.10 Emergency exit If the machine should turn over and the cabin door is closed, the right hand side cabin window can be used as an emergency exit.

4.11 Adjusting the steering wheel*

Fig. 60 l

Adjustment of steering wheel in height, pull lever (Fig. 60) up and move the steering wheel to the desired height.

l

Adjustment of steering wheel inclination, press lever down and adjust the inclination of the steering wheel. !

Danger

Danger of accident! After the adjustment make sure that the steering wheel adjustment is securely locked in place.

*

BW 211/212/213 D-40

BOMAG

Optional equipment

55

Operation

4.12 Adjusting the seat !

4.13 Operating the hood

Danger

!

Danger

Danger of accident!

Danger of accident!

Do not adjust the seat while driving.

If the hood needs to be opened further for maintenance or repair work, support it safely.

Bottom position

Fig. 61

To adjust the seat in longitudinal direction disengage the lever 1 (Fig. 61) and slide the seat forward or back.

Fig. 62

l

To adjust the weight actuate the lever (3).

l

Unlock the lock (Fig. 62).

l

To adjust the inclination of the backrest actuate the lever (2) and tilt the backrest forward or back.

l

To open the hood press in the button and turn the handle.

l

Fig. 63 l

Pull the support out of the bracket and support the hood (Fig. 63).

Top position l

56

BOMAG

Push the hood to top position.

BW 211/212/213 D-40

Operation

4.14 Towing in case of an engine failure !

Danger

Secure the machine with wheel chocks against unintentional rolling. Danger of accident! When using towing ropes tow the machine only uphill. Fig. 64 l

Pull the spring pin (Fig. 64) out of the bracket.

l

Secure the hood i´n the protection tube with spring plug.

When towing downhill you must use a rigid towing device. The machine cannot be steered. l

Secure the machine with wheel chocks against unintentional rolling.

Fig. 65 l

Attach chains (Fig. 65) or towing ropes to the lifting hooks.

! Caution Towing speed 1 km/h, max. towing distance 500 m.

l

BW 211/212/213 D-40

BOMAG

Open the tailgate.

57

Operation

After towing Caution Before detaching the tow bar block the machine with chocks to prevent unintended rolling. !

l

Turn the high pressure relief valve cartridges tightly back in.

l

Turn all brake releasing screws of the axle evenly back out, until they are light moving again.

Fig. 66

Slacken the middle hexagon on both valves (Fig. 66) for approx. 2 to 3 turns.

l

Caution Do not turn the valves out completely. !

Fig. 68 l

Turn the brake releasing screws (Fig. 68) back in again, until they abut against the brake piston.

Fig. 67 l

To release the brake turn counter nuts 1 (Fig. 67) approx. 8 mm back.

l

Turn the brake releasing screws (2) completely in against the stop. !

Caution

From this stop turn the screw in for maximum another turn to release the brake! Turn the screws in evenly on both sides.

Fig. 69

l

Turn the screws in alternately for ¼ turn at a time.

l

Unscrew the brake releasing screws (Fig. 69) for two turns and tighten the counter nuts.

l

Repeat this measure on the opposite wheel side.

l

Repeat this adjustment procedure on the opposite wheel side.

58

BOMAG

BW 211/212/213 D-40

Operation

i

Note

If necessary replace the seal ring under the counter nut if it is leaking. For this purpose completely unscrew the brake releasing screw, replace the seal ring and lubricate the screw with silicone grease. Reinstall the screw with a new seal ring and adjust the protrusion as described above.

4.15 Transport !

Danger

Danger of accident! Use only stable loading ramps of sufficient load bearing capacity. Make sure that persons are not endangered by the machine tipping or sliding off. Lash the machine down, so that it is secured against rolling, sliding and turning over. Do not stand or step under loads being lifted. Always use shackles on the lifting points for loading, tying or lifting the machine.

Fig. 70 l

Pull the spring pin (Fig. 70) out.

l

Engage the articulation lock and secure it with the spring pin.

Fig. 71 l

BW 211/212/213 D-40

BOMAG

Engage the articulation lock and secure it with the spring pin (Fig. 71).

59

Operation

Fig. 72 l

l

Lash the machine on the transport vehicle (Fig. 72), use the four lashing eyes on front and rear frame for this purpose.

Fig. 74

Position of centre of gravity (Fig. 74).

l

Support the front frame to avoid overstressing of the rubber buffers.

Machine

L

H

BW 211 - 214-4

1150±260

860±70

i

Note

The tolerances account for all possible options, such as cabin, additional weight etc. Weights: See technical data.

!

Danger

Danger of accident! The machine cannot be steered if the articulation lock is applied. l

Fig. 73 l

60

After transport release the articulation lock again and store it in the receptacle.

For lifting use also the four lifting eyes (Fig. 73) and appropriate lifting gear.

BOMAG

BW 211/212/213 D-40

Operation

4.16 BTM 05* settings before start-up Changing the units system

Fig. 77

Press key "F4" (Fig. 77).

l

i

Note

The screen page to select the unit system appears on the screen. Fig. 75

Turn the ignition key (Fig. 75) to position "I".

l

i

Note

The control unit shows the start screen.

Fig. 78 l

Press key "F5" (Fig. 78) and choose the units system.

Imperial 0

= metric units

Imperial 1

= imperial units

Fig. 76

Press key ’’?“ (menu) (Fig. 76).

l

i

Note

The menu appears on the screen.

*

Optional equipment

BW 211/212/213 D-40

BOMAG

61

Operation

Fig. 79

Fig. 81

After the desired change press key "F14" (Fig. 79). The "Save" symbol on the screen lights up green for a moment as confirmation.

l

i

Turn the ignition key to position "I" (Fig. 81).

l

i

Note

The control unit shows the start screen.

Note

After releasing key "F14" the system returns automatically to the start screen and restarts.

Fig. 82

Press key ’’?“ (menu) (Fig. 82).

l

Fig. 80

Switch the ignition off and on again (Fig. 80).

l

i

i

Note

The menu appears on the screen.

Note

Both Asphalt Manager control unit and printer have been set to the new units system.

Setting the printer language*

i

Note

With a printer* connected the language in the printout can be changed via the Asphalt Manager control unit. *

62

Optional equipment

BOMAG

BW 211/212/213 D-40

Operation

Fig. 83

Fig. 85

Press key "F6" (Fig. 83).

l

i

l

Note

Press key "F14" to save the language setting (Fig. 85). The "Save" symbol on the screen lights up green for a moment as confirmation.

The printer language screen page appears.

Fig. 86 l

Fig. 84

Use keys "F11" or "F12" to choose the desired printer language (Fig. 84).

l

i

Press key "ESC" (Fig. 86) to return to the start screen.

Note

The screen shows country flags, which represent the associated language.

BW 211/212/213 D-40

BOMAG

63

Operation

4.17 Measuring pass with BTM* General notes

i

Note

The soil measuring values (EVIB) recorded during different passes can only be compared if the recording of measuring values took place in operating mode "Manual" with the same amplitude, frequency and travel speed and on exactly the same track. Measuring values must only be compared for passes performed in the same direction.

Fig. 88 l

Control field F5 (Fig. 88) lights green.

The following description describes an measuring pass in forward. Measuring passes in reverse must be performed accordingly.

Measuring pass

Fig. 89 l

Turn the ignition key (Fig. 89) to position „II engine start.

Fig. 87 l

Turn the ignition key (Fig. 87) to position "I"

The BTM plus/prof performs a self-test.

*

64

Optional equipment

BOMAG

BW 211/212/213 D-40

Operation

Fig. 91 l

Pre-select working speed (Fig. 91) .

Fig. 90

Mark the track to be compacted (Fig. 90).

l

!

Caution

Since the transducer unit is mounted on the left hand side of the drum, it is necessary to arrange the tracks so that track 1 is processed first, followed by further tracks offset to the left. Fig. 92

i

l

Note

Maximum track length 150 m.

Turn the rotary switch (Fig. 92) for engine speed to position "MAX".

Forward: Mark 1

= Start of track

Mark 2

= End of track

i

Note

The operator may also remember the start and the end of the track by means of distinct points.

Fig. 93 l

Shift the travel lever (Fig. 93) fully to position „I“.

The machine accelerates up to the pre-adjusted travel speed.

BW 211/212/213 D-40

BOMAG

65

Operation

Caution Differences in the travel speeds falsify the measuring result! !

Fig. 96 l

When the end of the track, mark 2, is reached, press the button F6 “STOP” (Fig. 96).

l

Stop the machine.

Fig. 94

Switch the vibration on (Fig. 94).

l

i

Note

The first forward pass is finished. Caution Before reaching mark 1 the nominal exciter shaft speed must have been reached and a valid Evib-value should be displayed. !

Control field F5 lights green. This means, that the compaction is not yet completed. One or several passes are still required.

Fig. 95 l

When mark 1 is reached, press button F5 “START” (Fig. 95).

Control field to the left of F5 lights green. The EVIB- display shows the present value.

66

BOMAG

BW 211/212/213 D-40

Operation

4.18 Finishing compaction of a track

Fig. 97

Drive forward and reverse passes on a track until the green control field to the left of F5 (Fig. 97) goes out and the red control field F6 below lights up after pressing the stop button F6.

l

Fig. 98 l

Repeat the complete compaction process on the next track (Fig. 98) to record measuring values.

The compaction process on this track is finished. Criterion for a finished track: Compared with the previous track the increase of the EVIB-value in the same travel direction was less than 10%. This criterion is also fulfiled if the EVIB decreases.

i

Note

Another pass on this track does not make any sense, because an increase in load bearing capacity is hardly possible with this machine. l

If necessary print out the measuring data for this track (see following section).

BW 211/212/213 D-40

BOMAG

67

Operation

4.19 Printing measuring data after completing compaction* i

Note

Measuring data can be printed after completion of any pass. Always check the paper provision before starting work. Change the paper roll if a red stripe appears on the paper.

Fig. 100 l

If no further printouts of this track are needed, press the button F8 “DELETE” (Fig. 100) when the red control lamp F6 “FINISHED” lights up.

The red control field F6 “FINISHED” goes out and the green control field F5 “CONTINUE” lights up. BTM plus/prof is ready to compact the next track.

Fig. 99

At the end of the measurement press push button F7 "PRINT" (Fig. 99).

l

short actuation = Line diagram long actuation ≥5 sec. = Bar chart Control field F7 goes out and the measuring value printer starts to print out measuring data.

i

Note

After the printing process has finished any amount of diagrams can be printed out by pressing the same button F7 (PRINT).

*

68

only BTM prof

BOMAG

BW 211/212/213 D-40

Operation

4.20 Changing the paper roll in the measuring value printer* i

Note

Use a new paper roll if a red stripe appears on the paper.

Fig. 103 l

Insert a new paper roll (Fig. 103).

l

Feed the paper into the guide (1) on the printer.

l

Actuate the toggle switch (2) in direction of arrow, until the paper comes out of the printer.

l

Reassemble the cover.

Fig. 101 l

Unscrew the star handles (Fig. 101) and remove the cover.

Fig. 102 l

*

Remove shaft 1 (Fig. 102) with the rest of the paper roll (2).

only BTM prof

BW 211/212/213 D-40

BOMAG

69

Operation

4.21 Changing the printer ribbon in the measuring value printer* i

Note

In case of faint or poorly legible diagrams the printer ribbon needs to be replaced.

Fig. 104 l

Unscrew the star handles (Fig. 104) and remove the cover.

Fig. 105 l

Lift the tongue at point 1 (Fig. 105) and take the printer ribbon (2) out of the printer.

l

Insert the new printer ribbon into the printer, then press in the tongue (1) on the right.

l

Tension the printer ribbon by turning the rotary button (3) in direction of arrow.

l

Reassemble the cover.

*

70

only BTM prof

BOMAG

BW 211/212/213 D-40

5 Maintenance

BW 211/212/213 D-40

BOMAG

71

Maintenance

l

Do not let the suction hose disturb the sludge on the bottom of the drum.

l

Do not draw off fuel from near the bottom of the fuel drum.

When servicing the machine pay careful attention to all applicable safety instructions.

l

Thorough maintenance of the machine ensures maximum reliability and prolongs the lifetime of important components. The necessary effort can by no means be compared with the problems and malfunctions that could occur if this is not observed.

Fuel left in the fuel drum is not suitable for the engine and should only be used for cleaning purposes.

Notes on the engine performance

5.1

General notes on maintenance

The terms left/right are always related to travel direction forward.

Combustion air and fuel injection rates of the diesel engine have been carefully adjusted and determine the engine's performance and temperature level as well as the quality of the exhaust gas.

l

Clean machine and engine thoroughly before starting maintenance work.

l

For maintenance work park the machine on level ground.

If your machine has to operate permanently in "thin air" (at high altitudes) and with full power, you should consult the after sales service of BOMAG or the service department of the engine manufacturer.

l

Maintenance work must generally be carried out with the engine shut down.

Notes on the hydraulic system

l

Depressurize hydraulic lines before working on them.

l

Disconnect the battery and cover it with insulation material before starting to work on electrical components.

l

Always attach the articulation lock (transport lock) before starting to work in the articulation area of the machine.

Environment Catch running out oils, coolant and fuel and do not let them seep into the ground or into the sewage system. Dispose of oils, coolant and fuels environmentally.

Notes on the fuel system

During maintenance work in the hydraulic system cleanliness is of utmost importance. Make sure that no dirt or other impurities can enter into the system. Small particles can flute valves, cause pumps to seize and block restrictors and pilot bores, thereby causing costly repairs. l

If during the daily oil level check the oil level is found to have dropped, check all lines, hoses and components for leakages.

l

Seal external leaks immediately. If necessary inform the responsible service department.

l

Do not store drums with hydraulic oil outside, or at least keep them under a cover. During weather changes water may penetrate through the bunghole.

l

Always fill the hydraulic system using the filling and filtering unit (BOMAG part-no. 007 610 01). This unit is equipped with a fine filter, which filters the hydraulic oil and prolongs the lifetime of the system filter.

l

Clean fittings, filler caps and their immediate surrounding area before removing them, so that no dirt can fall in.

l

Do not leave the tank opening unnecessarily open, cover it so that no dirt can fall in.

The lifetime of the diesel engine is decisively depending on the cleanliness of the fuel. l

l

l

72

Keep the engine free of dirt and water as this could damage the injection elements of the engine. Zinc lined drums are not suitable for storing fuel. The fuel drum should rest for a longer period of time before drawing off fuel.

BOMAG

BW 211/212/213 D-40

Maintenance

Notes on the cooling system On water cooled engines the preparation and monitoring of the coolant is of utmost importance, as otherwise engine failures caused by corrosion, caviation and freezing may occur.

5.2

Engine oil Quality

The coolant is a mixture of water and a cooling system protection agent. The cooling system must be permanently monitored. Apart from the coolant level inspection this includes also the inspection of the concentration of cooling system protection agent.

Lubrication oils are classified according to their performance and quality class. Oils according to other comparable specifications may be used. Approved engine oils Deutz DQC II ACAE E3/96/E5-02 API CH-4/CG-4 DHD DHD-1

The concentration of the cooling system protection agent can be checked with commercially available test instruments (glycomat). !

Fuels and lubricants

Danger

Health hazard! The mixing of nitride based cooling system protection agents with amine based agents will cause the generation of highly toxic nitrosamines.

DQC III E4-99 -

The exact assignment of the approved oil qualities and oil change intervals can be taken from the following section "Lubrication oil change intervals". Consult your local service station if in doubt. Oil viscosity Multi-purpose oils should be generally used.

Environment Cooling system protection agents must be disposed of environmentally.

Since lubrication oil changes its viscosity with the temperature, the ambient temperature at the operating location of the engine is of utmost importance when choosing the viscosity class (SAEclass) . Optimal operating conditions can be achieved by using the opposite oil viscosity chart (Fig. 106) as a reference. Occasionally falling short of the temperature limits will impair the cold starting ability, but will not cause any engine damage. In order to keep the occurring wear as low as possible, occassional exceeding of the limits should not happen over a longer period of time.

BW 211/212/213 D-40

BOMAG

73

Maintenance

and for ambient temperatures higher than -10 °C. When using fuels with a sulphur content of more than 0.5% to 1% or under ambient temperatures below -10 °C the oil change intervals specified in the table must be halved. For fuels with a sulphur content of more than 1% you should consult the responsible service agency.

Fuels Quality You should only use commercially available brand diesel fuel with a sulphur content below 0.5% and ensure strict cleanliness when filling in. A higher sulphur content has a negative effect on the oil change intervals. Use only winter-grade diesel fuel under low ambient temperatures. The fuel level should always be topped up in due time so that the fuel tank is never run dry, as otherwise filter and injection lines need to be bled. When using fuels with a Cetan number < 49 poor starting and white smoke can be expected, in particular in connection with low ambient temperatures. Fig. 106

With their better temperature and oxidation stability synthetic lubrication oils offer quite a few benefits.

The following fuel specifications are permitted: DIN/EN 590; DIN 51 601; Nato Codes: F-54, F-75; BS 2869: A1 and A2; ASTM D 975-78: 1-D and 2D.

Oil change intervals

l

DIN/EN 590

l

BS 2869

l

ASTM D 975-78: 1-D and 2-D.

l

Nato Codes: F-54, F-34, F44 und XF63

The longest permissible time a lubrication oil should remain in an engine is 1 year. If the following oil change intervals are not reached over a period of 1 year, the oil change should be performed at least once per year, irrespective of the operating hours reached. ACEA*

Winter fuel Danger Fire hazard! !

E3-96/E5-02 E4-99

= 500 operating hours

Diesel fuels must never be mixed with gasoline.

API** CG-4/CH-4

= 500 operating hours

Caution These intervals apply only when using a diesel fuel with maximum 0.5 % sulphur by weight !

* **

74

For winter operation use only winter diesel fuel, to avoid clogging because of paraffin separation. At very low temperatures disturbing paraffin separation can also be expected when using winter diesel fuel.

European Engine Oil Sequences American Petroleum Institute

BOMAG

BW 211/212/213 D-40

Maintenance

In most cases a sufficient cold resistance can also be achieved by adding flow enhancing fuel additives. Consult the engine manufacturer. Operation with rape seed oil methyl ester (RME „Bio Diesel“) Due to the extreme quality differences of RMEWfuels available on the market, which are caused by the non-existence of a standardization, BOMAG does generally not approve any RME-fuels. If this is neglected the warranty will become null and void! However, if you still intend to operate the machine with RME-fuels you should observe the following information: l

Reduced engine power (approx. 7%), higher fuel consumption.

l

The quality of RME-fuel should be in compliance with DIN draft 51606.

l

Avoid longer periods of standstill (formation of resin, corrosion in injection system)

l

RME-fuel can damage the paint finish of the machine.

l

Fuel dilution of engine oil, therefore shortening of oil change intervals to half.

l

Rubber parts, such as leak fuel return lines, seats will be damaged in the long run and need to be replaced on a regular basis or should be replaced by parts made of fluorinated rubber. However, fluorinated rubber is not resistant against normal diesel fuel.

l

Environment Cooling system protection agents must be disposed of environmentally.

Hydraulic oil The hydraulic system is operated with hydraulic oil HV 46 (ISO) with a kinematic viscosity of 46 mm 2/s at 40°C. For topping up or for oil changes use only high-quality hydraulic oil, type HVLP according to DIN 51524, part 3, or hydraulic oils type HV according to ISO 6743/3. The viscosity index (VI) should be at least 150 (observe information of manufacturer). Bio-degradable hydraulic oil On request the hydraulic system can also be filled with ester based biodegradable hydraulic oil (Panolin HLP Synth. 46). The biologically quickly degradable hydraulic oil meets all demands of a mineral oil based hydraulic oil according to DIN 51524. In hydraulic systems filled with Panolin HLP Synth. 46 always use the same oil to top up. When changing from mineral oil based hydraulic oil to an ester based biologically degradable oil, you should consult the lubrication oil service of the oil manufacturer for details. Check the filter more frequently after this change. Caution Oil change bio-degradable hydraulic oil: !

Perform regular oil analyses for content of water and mineral oil.

If the fuel filter is clogged the filter change intervals must be shortened accordingly.

Coolant, anti-freeze agent

Replace the hydraulic oil filter element every 500 operating hours.

Use only soft tap water (drinking water) to prepare the coolant mix.

Oil for drive axle

As a protection against frost, corrosion and boiling point anti-freeze agents must be used under any climatic conditions.

For the drive axle use only multi-purpose transmission oil of API-class GL5 with viscosity class SAE 90.

The proportion of cooling system protection agent must be between min. 35% and max. 45% to the water.

The additives in this oil ensure low wear lubrication under all operating conditions.

Lubrication grease ! Caution Do not mix different coolants and additives of any other kind.

BW 211/212/213 D-40

For lubrication use only EP-high pressure grease, lithium saponified (penetration 2).

BOMAG

75

Maintenance

5.3

Table of fuels and lubricants

Assembly

Fuel or lubricant Summer

Winter

Quantity approx. Attention Observe the level marks

Engine

Engine oil ACEA: E3-96/E5-02 or

approx. 8,5 litres without oil filter

API: CG-4/CH-4 SAE 10W/40 (-20 °C to +40 °C) SAE 15W/40 (-15 °C to +40 °C) Fuel Diesel Hydraulic system

Winter diesel fuel

Hydraulic oil (ISO), HV46, kinem. viscosity

approx. 150 litres approx. 60 litres

46 mm2/s at 40 °C Vibration bearings

Engine oil SAE 15W/40

approx. 0,8 litres

Drive axle

Gear oil SAE 90, API GL5

approx. 9,5 litres

Wheel hubs

Gear oil SAE 90, API GL5

approx. 1,9 per side

Air conditioning system Tires (only BW 213)

Engine cooling system

76

Refrigerant R134A Water

approx. 1400 g approx. 295 litres

Calcium chloride (CaCl2) or magnesium chloride (MgCl2)

approx. 100 kg

Cooling system protection agent

approx. 16 litres

BOMAG

BW 211/212/213 D-40

Maintenance

5.4

Running-in instructions

The following maintenance work must be performed when running in new machines or overhauled engines: ! Caution Up to approx. 250 operating hours check the engine oil level twice every day.

Depending on the load the engine is subjected to, the oil consumption will drop to the normal level after approx. 100 to 250 operating hours. After a running-in time of 30 minutes l

Retighten the V-belt

After 250 operating hours l

Retighten bolted connections on intake and exhaust tubes, oil sump and engine mounts.

l

Retighten the bolted connections on the machine.

l

Retighten all wheel fastening screws with the specified tightening torque.

l

Changing engine oil and oil filter

l

1. Oil change vibration bearings

l

Oil change in drive axle

l

Oil change in wheel hubs

After 500 operating hours l

BW 211/212/213 D-40

BOMAG

2. Oil change vibration bearings

77

Maintenance

Dipstick mark

5.7

Check the water separator

X

5.8

Check the fuel level

X

5.9

Check the hydraulic oil level

5.10 Check the coolant level

X

Inspection glass

X

Inspection glass

X

5.11 Check the dust separator

X

5.12 Check the tire pressure

X

5.13 Clean the cooling fins on engine and hydraulic oil cooler

X

5.14 Check the oil level in the drive axle

X

5.15 Check the oil level in the wheel hubs

X

5.16 Check the oil level in the vibration bearings

X

5.17 Change engine oil and oil filter cartridge*

min. 1x per year

5.18 Drain the sludge from the fuel tank 5.19 Service the battery

X

X X

Pole grease

X

5.20 Check, replace the refrigerant compressor V-belt

X

5.21 Service the air conditioning

X

5.22 Check, adjust the valve clearance

as required

Check the engine oil level

every 3000 operating hours

5.6


Remark


Maintenance work


No.


every 10 operating hours, daily

Maintenance chart

Running-in instructions after 250 operating hours

5.5

Intake = 0,3 mm

X

Exhaust = 0,5 mm 5.23 Check, replace the ribbed V-belt

X

5.24 Change the fuel filter cartridge

78

X

BOMAG

BW 211/212/213 D-40

5.25 Change the fuel pre-filter cartridge

as required

X

5.26 Check the engine mounts

X

X

5.27 Oil change in drive axle

min. 1x per year

X

X

5.28 Oil change in wheel hubs

min. 1x per year

X

X

5.29 Oil change vibration bearings**

see foot note, min. X 1 x per year

X

5.30 Retighten the fastening of the axle on the frame

X

5.31 Tighten the wheel nuts

X

5.32 Check the ROPS

X X

5.33 Clean the oil bath air filter

min. 1x per year

5.34 Change hydraulic oil and breather filter***

at least every 2 years

X

5.35 Change the hydraulic oil filter***


X

5.36 Change the coolant


X

5.37 Check the injection valves 5.38 Service the combustion air filter





Remark


Maintenance work

every 10 operating hours, daily

No.

Running-in instructions after 250 operating hours

Maintenance

X

X min. 1x per year, safety cartridge at least every 2 years

X

5.39 Adjusting the scrapers

X

5.40 Adjust the parking brake

X

5.41 Change the tires

X

5.42 Change the fresh air filter in the cabin

X

5.43 Tightening torques

X

5.44 Engine conservation

X

BW 211/212/213 D-40

BOMAG

79

Maintenance

* Oil change intervals depend on quality of oil and fuel (sulphur content) ** Oil change intervals after 250 h, after 500 h, after 1000 h, and then every 1000 h. *** Also in case of repair in the hydraulic system.

80

BOMAG

BW 211/212/213 D-40

Every 10 operating hours

Every 10 operating hou rs

5.6 !

Check the engine oil level

5.7

Danger

Danger of injury!

!

Danger

Danger of injury!

Support the engine hood for all maintenance and repair work.

i

Check, clean the water separator

Support the engine hood for all maintenance and repair work.

Note

The machine must be parked horizontally with the engine shut down.

i

Note

The service intervals for the water separator depend on the water content in the fuel and can therefore not be determined precisely. After taking the engine into operation you should therefore check the water separator every day for signs of water. If a to high quantity is drained off, the filter must be refilled with fuel. See chapter "maintenance as required", bleeding the fuel system. Environment Catch running out fuel and dispose of environmentally.

Fig. 107 l

Pull the dipstick (Fig. 107) out, wipe it off with a lint-free, clean cloth and reinsert it until it bottoms.

l

Pull the dipstick back out again.

l

If the oil level is below the "MAX" mark fill in oil.

l

If the oil level is above the “Max” mark determine the cause and drain the oil off.

Caution Before longer work periods you should always top the oil up to the "MAX"-mark. !

For quality and quantity of oil refer to the table of fuels and lubricants.

BW 211/212/213 D-40

Fig. 108 l

Slacken the drain plug (Fig. 108) for a few turns and catch running out fuel / water.

l

Tighten the drain plug again and check for leaks, if necessary replace the seal ring.

BOMAG

81


5.8 !

Checking the fuel level

Danger

Fire hazard! When working on the fuel system do not use open fire, do not smoke, do not refuel in closed rooms, do not inhale any fuel fumes.

Caution Dirty fuel can cause engine failures or even damage to the engine. !

If necessary fill in fuel through a screen filter. l

If necessary top up fuel (diesel or winter diesel).

For quality of fuel refer to the table of fuels and lubricants.

Fig. 109

Check the fuel level on the fuel gauge (Fig. 109).

l

i

Note

Never drive the fuel tank empty, because this would required bleeding of the entire fuel system. l

Clean the area around the filler opening.

Fig. 110 l

82

Open the fuel tank cover (Fig. 110).

BOMAG

BW 211/212/213 D-40


5.9

Checking the hydraulic oil level

5.10 Checking the coolant level !

!

Danger

Danger of scalding!

Caution

In mit Panolin HLP Synth. 46, the same oil must be used for filling up. In case of any other ester based oil consult the lubrication service department of the respective oil manufacturer.

Top up coolant only when the engine is cold.

Fig. 112

Check the coolant level (Fig. 112).

l

Fig. 111

Check the oil level in the inspection glass (Fig. 111) on the hydraulic oil tank.

l

Normal level approx. 3 cm below the upper edge of the inspection glass. Minimum level

Caution If during the daily coolant level check the coolant level is found to have dropped, check all lines, hoses and engine for leakages. !

l

To top up unscrew the lid and fill in coolant up to the MAX-mark.

For quality of coolant refer to the table of fuels and lubricants in chapter 5.2.

middle of inspection glass. Caution If during the daily oil check the oil level is found to have dropped, check all lines, hoses and components for leakages. !

l

If necessary fill in hydraulic oil through the filler neck.

For quality and quantity of oil refer to the table of fuels and lubricants.

BW 211/212/213 D-40

BOMAG

83


5.11 Checking the dust separator on the oil bath air filter*

Fig. 113 l

*

84

If the dust reaches the mark loosen the clamp (Fig. 113), take the cover off and clean the bowl.

Option

BOMAG

BW 211/212/213 D-40


Every 250 oper ating hours

5.12 Checking the tire pressure

5.13 Clean the cooling fins on engine and hydraulic oil cooler

! Caution Always close the valves with the dust cap.

Danger Danger of injury! !

Perform cleaning work only after the engine has cooled down and with the engine stopped. Caution Do not damage any cooling fins on the cooler core when cleaning. !

i Fig. 114

Check the tire pressure with a pressure gauge and the tire inflation valve 1 (Fig. 114) in top position.

l

Note

Dirt on fan blades and oil cooler reduce the cooling effect. Dirt deposits in these areas are substantially supported by oil and fuel on these surfaces. For this reason you should always seal any oil or fuel leaks in the vicinity of the cooling fan or the oil cooler and clean the cooling surfaces after.

Nominal value see "Technical Data".

Cleaning with compressed air

i

Note

Ensure even pressure in all tires. l

Screw the valve caps back on.

Fig. 115

i

Note

Start to blow out from the exhaust side. l

BW 211/212/213 D-40

BOMAG

Blow the cooler (Fig. 115) out with compressed air.

85


Cleaning with cold cleansing agent Caution Protect electrical equipment such as generator, regulator and starter against the direct water jet. !

l

Spray the engine with a suitable cleansing agent, e.g. cold cleanser, let it soak in for a while and spray it off with a strong water jet.

l

Run the engine warm for a while to avoid corrosion.

5.14 Check the oil level in the drive axle Park the machine on level ground.

l

Fig. 116

Unscrew the oil level inspection plug (Fig. 116) and check the oil level.

l

i

Note

The second level inspection plug as at the back. After filling in oil wait until the oil has evenly distributed inside the axle. The oil level must reach the bottom edge of the level bore. l

Top up oil, if necessary.

For quality of oil refer to the table of fuels and lubricants. l

86

BOMAG

Turn the level inspection plug tightly back in.

BW 211/212/213 D-40


5.15 Checking the oil level in left/ right wheel hubs

5.16 Checking the oil level in the vibration bearing housings i

Note

Check the oil level only at operating temperature after running the vibration for about 1/2 hour.

Fig. 117 l

Move the machine until the oil level inspection plug 1 (Fig. 117) is in horizontal position.

l

Clean and unscrew the plug. Fig. 118

The oil level must reach the bottom edge of the bore. l

l

Move the drum so that the oil level control plug (Fig. 118) on the left hand side is in lowest position.

l

Unscrew the control plug (1).

Top up oil, if necessary.

For quality of oil refer to the table of fuels and lubricants. l

Screw the plug back in tightly.

l

Repeat this inspection on the other side.

Some oil should drip out of the level bore l

If necessary unscrew the oil filler plug (2) and fill in some oil through the filler bore (2), until it starts to run out from the level inspection bore.

For quality of oil refer to the table of fuels and lubricants.

BW 211/212/213 D-40

l

Screw the oil filler (2) and control plug (1) back in.

l

Repeat this procedure on the opposite side.

BOMAG

87


88

BOMAG

BW 211/212/213 D-40


Every 500 oper ating hours

5.17 Changing engine oil and oil filter cartridges !

Caution

The oil change at 500 operating hours refers to the use of fuels with a sulphur content of less than 0.5%. When using fuels with a sulphur content higher than 0.5 % the oil change intervals must be halved (see section 5.2 fuels and lubricants). Fig. 120

Drain the engine oil only when the engine is warm. Danger Danger of scalding! !

When draining off hot oil. Environment Catch running out oil and dispose of environmentally together with the engine oil filter cartridge.

l

Thoroughly clean the outside of the filter cartridge (Fig. 120).

l

Unscrew the filter cartridge using an appropriate filter wrench.

l

Clean the sealing face on the filter carrier from any dirt.

l

Slightly oil the rubber seal on the new filter cartridge.

Fig. 121 l

Turn the new filter cartridge (Fig. 121) on by hand, until the seal contacts.

l

Tighten the filter element for another half turn.

Fig. 119 l

Unscrew the drain plug (Fig. 119) and catch running out oil.

l

Turn the drain plug tightly back in.

BW 211/212/213 D-40

BOMAG

89


5.18 Draining the fuel tank sludge !

Danger

Fire hazard! When working on the fuel system do not use open fire, do not smoke. Do not spill any fuel. Catch running out fuel, do not let it seep into the ground.

Fig. 122

Do not inhale any fuel fumes.

Fill in new engine oil (Fig. 122).

l

For quality and quantity of oil refer to the table of fuels and lubricants. Tighten the oil filler cap properly.

l

!

Caution

Before starting crank the engine with the starter motor until the oil pressure warning light goes out. l

After a short test run check the oil level on the dipstick, if necessary top up to the top dipstick mark.

l

Check filter cartridge and drain plug for leaks after a short test run.

l

Shut the engine down and wait for about 15 minutes, so that all oil can flow back into the oil sump.

l

Check the oil level again , if necessary fill up to the Max.-mark.

90

Fig. 123 l

Unscrew the drain plug (Fig. 123) from the bottom of the fuel tank and drain off approx. 5 litres of fuel.

l

Screw the drain plug back in with a new sealing ring.

BOMAG

BW 211/212/213 D-40


Caution Exhausted batteries (batteries with formation of sulphate on the plates are not covered under warranty!

5.19 Service the battery !

!

Danger

Danger of cauterisation ! Danger of explosion!

l

Open the engine hood and remove the covering

When working on the battery do not use open fire, do not smoke! The battery contains acid. Do not let acid come in contact with skin or clothes! Wear protective clothing! Do not lay any tools on the battery! Environment Dispose of the old battery environmentally.

i

Note

Maintenance free batteries also need care. Maintenance free only means that the fluid level does not need to be checked. Each battery suffers under self-discharge, which may, in not checked occasionally, even cause damage to the battery as a result of exhaustive discharge.

Fig. 124 l

Remove the battery (Fig. 124) and clean the battery compartment.

l

Clean the outside of the battery.

l

Clean battery poles and pole clamps and grease them with pole grease (Vaseline).

l

Check the fastening of the battery.

l

On serviceable batteries check the acid level, if necessary top up to the filling mark with distilled water.

The following therefore applies for the service life: l

l

Switch off all consumers (e.g. ignition, light, inside light, radio). Check open-circuit voltage of the battery at regular intervals. At least once per month.

Reference values: 12.6 V = fully charged; 12.3 V = 50% discharged. l

Charging voltage recommendation

Recharge the battery immediately after an open-circuit voltage of 12.25 V or less is reached. Do not perform boost charging.

The open-circuit voltage of the battery occurs approx. 10 hours after the last charging process or one hour after the last discharge. l

After each charging process allow the battery to rest for one hour before taking it into service.

l

For resting periods of more than one month you should always disconnect the battery. Do not forget to perform regular open-circuit voltage measurements.

BW 211/212/213 D-40

Fig. 125

BOMAG

91


5.20 Check condition and tension of refrigerant compressor V-belt, replace the V-belt

Tensioning the V-belt

Danger Danger of injury! !

Work on the V-belt must only be performed with the engine shut down.

Checking the V-belt Fig. 127 l

Slightly slacken the fastening screws 1, 2 and 3 (Fig. 127).

l

Press the compressor in direction of arrow, until the correct V-belt tension is reached.

l

Retighten all fastening screws.

Changing the V-belt

Fig. 126 l

l

92

Inspect the entire circumference of the V-belt (Fig. 126) visually for damage and cracks. Replace damaged or cracked V-belts. Check with thumb pressure whether the V-belt can be depressed more than 10 to 15 mm (0.4 – 0.6 inches) between the V-belt pulleys, retighten if necessary.

l

Slightly slacken the fastening screws 1, 2 and 3.

l

Press the compressor against the direction of arrow completely against the engine.

l

Take the old V-belt off.

l

Fit the new V-belt to the V-belt pulleys.

l

Tension the V-belt as previously described.

! Caution Check the V-belt tension after a running time of 30 minutes.

BOMAG

BW 211/212/213 D-40


5.21 Service the air conditioning*

Checking the refrigerant level Start the engine.

l

Cleaning the condenser ! Caution A soiled condenser results in a considerable reduction of air conditioning power.

Under extremely dusty conditions it may be necessary to clean the condenser several times per day. If, during operation of the air conditioning system, the warning buzzer sounds switch the air conditioning off and clean the condenser. Fig. 129

In case of formation of foam have the air conditioning system inspected by the service department.

Switch the air conditioning (Fig. 129) on.

l


Do not clean with a hot water jet. Heat will cause extreme overpressure, which could cause damage or explosion of the system. Use access steps and grips to mount and dismount the machine.

Fig. 130 l

Choose a cooling temperature with the rotary switch for cabin heater (Fig. 130) in the blue section.

l

Open the air outlet nozzles.

l

Check, whether the outflowing air is noticeably cooler.

i Fig. 128 l

Unscrew the condenser fastening screws (Fig. 128) and fold the condenser forward.

l

Clean the condenser fins on front and back with compressed air or cold water .

*

Note

The adjusted temperature must be below the actual temperature inside the cabin, so that the compressor will be switched on. l

Open the hood.

Optional equipment

BW 211/212/213 D-40

BOMAG

93

Every 500 operating hours Checking the moisture level of the drying agent

Fig. 131

Check whether the white float (Fig. 131) inside the inspection glass of the drier/collector unit floats right at the top.

l

Fig. 133

Check the moisture indication pearl (Fig. 133) inside the inspection glass of the drier/collector unit.

l

i

Note

The refrigerant level is correct.

orange

= drying agent o.k.

colorless = moisture level of drying agent too high. Inform the service department. Replace drier/ collector unit, check air conditioning system.

l

Caution Have the drier/collector unit replaced by the service department every year before the operating season. !

Fig. 132

If the white float (Fig. 132) inside the inspection glass of the drier/collector unit floats at the bottom, inform the service department.

l

i

Note

The refrigerant level is not correct. l

94

Refrigerant must be filled up, if necessary check the air conditioning system for leaks.

Checking the condition of the drier/collector unit Caution According to the regulation for pressure reservoirs all pressure reservoirs must be repeatedly inspected by a specialist. In this sense repeated inspections are external examinations, normally on pressure reservoirs in operation. In connection with this inspection the drier/collector unit must be visually examined twice every year. During these inspections special attention must be paid to corrosion and mechanical damage. If the reservoir is not in proper condition it must be replaced for safety reasons, as a precaution to protect operators and third parties against any danger !

BOMAG

BW 211/212/213 D-40

Every 500 operating hours arising from the handling and operation of pressure reservoirs. !

Danger

Danger of injury! In case of mechanical damage or corrosion on this drier/collector unit this unit must be replaced, to avoid bursting and further damage.

Fig. 134 l

Check the drier/collector unit (Fig. 134) for mechanical damage or rust.

BW 211/212/213 D-40

BOMAG

95


96

BOMAG

BW 211/212/213 D-40

Every 1000 operating hours Every 1000 operating hours

5.22 Check, adjust the valve clearance !

Caution

Before checking the valve clearance let the engine cool down for at least 30 minutes. The engine oil temperature must be less than 80 °C. After a short test run check the engine for leaks.

Valve adjustment schematic

Fig. 136

Crankshaft position 1 (Fig. 136) (4 cylinder engine) l

Crank the engine with the starter or a spanner by the V-belt pulley until both valves on cylinder 1 are “overlapping”.

Overlapping means: Exhaust valve not yet closed, intake valve starts to open. l

Perform the adjustment of the valve by following the adjustment diagram "crankshaft position 1", black mark.

l

For control purposes mark the respective rocker arm with while chalk once the corresponding valve is adjusted.

Fig. 135

Valve 1 (Fig. 135) white = not adjustable Valve (2) black = adjustable

Fig. 137

Crankshaft position 2 (Fig. 137) (4 cylinder engine)

BW 211/212/213 D-40

l

Turn the crankshaft one revolution (360°) further.

l

Perform the adjustment of the valve by following the adjustment diagram "crankshaft position 2", black mark.

BOMAG

97

Every 1000 operating hours Check the valve clearance l

Adjusting the valve clearance

Loosen the crankcase ventilation valve and swing it to the side.

Fig. 140 l

Slightly slacken the counter nut. Adjust setscrew 7 (Fig. 140) with a screwdriver, until the feeler gauge (6) can be inserted and pulled out with little resistance after retightening the counter nut.

l

Perform tests and adjustments on all other adjustable valves.

l

Check the gasket of the valve cover, replace it if necessary.

l

Reassemble the cylinder head cover.

l

Swivel the ventilation valve back to correct position and fasten it.

l

Fasten the air filter again and ensure correct fit of combustion air hoses and clamps.

Fig. 138 l

Remove the valve cover (Fig. 138).

l

Crankshaft position as per "valve adjustment schematic".

Fig. 139 l

Check valve clearance 2 (Fig. 139) between rocker arm (1) and valve (3) with a feeler gauge.

Intake valve

= 0,3 mm

Exhaust valve = 0,5 mm The feeler gauge must fit with little resistance. l

98

If the gap is too narrow or too wide for the feeler gauge, the valve must be adjusted.

BOMAG

BW 211/212/213 D-40

Every 1000 operating hours Changing the ribbed V-belt

5.23 Checking / replacing the ribbed V-belt !

Danger

Danger of injury! Work on the V-belt must only be performed with the engine shut down.

Checking the wear limit of the ribbed Vbelt Fig. 142

Unscrew the fastening screws (Fig. 142) and slide the fan forward.

l

Fig. 141 l

Check the distance between the tongue of the moveable tensioner arm and the fixed tensioner housing (Fig. 141).

l

If measurement "a" is smaller than 3 mm, replace the ribbed V-belt.

Fig. 143 l

Release the idler pulley (Fig. 143) in direction of arrow until the ribbed V-belt is free.

l

Pull the ribbed V-belt first to the smallest pulley.

l

Install the new ribbed V-belt.

l

Release the idler pulley against the direction of arrow until the V-belt is tensioned.

l

Measure the V-belt tension, tighten if necessary.

i

Note

Retighten the new fan V-belt after a running time of 20 minutes.

BW 211/212/213 D-40

BOMAG

99

Every 1000 operating hours 5.24 Change the fuel filter cartridge !

Danger

l

Fill the filter cartridge with clean diesel fuel.

l

Turn the new filter cartridge on by hand, until the seal contacts.

l

Tighten the filter element for another half turn.

l

Check the filter cartridge for leaks after a short test run.

Fire hazard! When working on the fuel system do not use open fire, do not smoke and do not spill any fuel. Catch running out fuel, do not let it seep into the ground. Do not inhale any fuel fumes.

Fig. 144 l

Loosen and unscrew the fuel filter cartridge (Fig. 144) using an appropriate filter wrench.

l


Fig. 145 l

100

Slightly oil the rubber seal (Fig. 145) on the new filter cartridge.

BOMAG

BW 211/212/213 D-40

Every 1000 operating hours 5.25 Change the fuel pre-filter cartridge !

Danger

Fire hazard! When working on the fuel system do not use open fire, do not smoke and do not spill any fuel. Catch running out fuel, do not let it seep into the ground. Fig. 148

Do not inhale any fuel fumes.

Fig. 146 l

Unscrew the fuel filter cartridge (Fig. 146) using an appropriate filter wrench.

l


l

Apply a thin coat of oil to the rubber seal of the water separator 1 (Fig. 148).

l

Screw the water separator on by hand (2), until the seal contacts.

l

Tighten the water separator for another half turn (3).

l

Fill the filter cartridge with clean diesel fuel (4).

l

Apply some oil to the rubber seal of the filter element (5) and screw it on by hand, until the seal contacts.

l

Tighten the filter element for another half turn (6).

l

Check the filter cartridge for leaks after a short test run.

i

Note

Air in the fuel system causes irregular running of the engine, a drop in engine power, stalls the engine and makes starting impossible. Therefore bleed the fuel system after changing the fuel prefilter.

Fig. 147 l

Unscrew the water separator from the filter cartridge (Fig. 147).

BW 211/212/213 D-40

BOMAG

101

Every 1000 operating hours 5.26 Check the engine mounts

Fig. 149 l

Slacken the bleeding screw (Fig. 149) on the fuel pre-filter for 2 to 3 turns.

l

Operate the hand pump manually, until fuel flows out of the slackened bleeding screw (Fig. 149) without air bubbles.

Fig. 150 l

Tighten fastenings of intake and exhaust manifolds (Fig. 150) on the cylinder heads.

Then tighten the bleeding screw while pumping.

l

Check sockets and clamps between air filter, exhaust turbocharger and charge air line as well as the lubrication air line for tight fit and leaks.

l

Retighten the fastening screws for oil sump and engine mounts.

l

102

BOMAG

BW 211/212/213 D-40

Every 1000 operating hours 5.27 Change the oil in the drive axle i

Note

On other axle versions drain and filler plugs are of slightly different design. Perform the oil change accordingly. Caution Drain oil only at operating temperature. !

Fig. 152

l

Fill in oil through the oil level inspection bores (Fig. 152), until it has reached the bottom edge of the bore.

l

Environment Catch old oil and dispose of environmentally. Park the machine on level ground.

i

Note

The second level inspection plug as at the back. After filling in oil wait until the oil has evenly distributed inside the axle. For quality and quantity of oil refer to the table of fuels and lubricants. l

Retighten the filler and level inspection plug.

Fig. 151 l

Clean and unscrew all level inspection and drain plugs (Fig. 151).

l

Drain and catch all oil.

l

Clean the drain plug and turn it back in with a new seal ring.

BW 211/212/213 D-40

BOMAG

103

Every 1000 operating hours 5.28 Changing the oil in the wheel hubs !

For quality and quantity of oil refer to the table of fuels and lubricants. l

Turn the plug tightly back in.

Caution

Drain oil only at operating temperature. Change the oil on both sides of the axle. Environment Catch old oil and dispose of environmentally.

Fig. 153 l

Move the drive wheel, until the plug (Fig. 153) is in bottom position.

l

Clean and unscrew the plug.

l

Drain and catch all oil.

Fig. 154 l

Move the drive wheel, until the plug (Fig. 154) is in horizontal position on the housing.

l

Fill in oil, until it reaches the bottom edge of the bore.

104

BOMAG

BW 211/212/213 D-40

Every 1000 operating hours 5.29 Changing the oil for the vibration bearings !

Caution

Change the oil at operating temperature. For this purpose run the machine approx. half an hour with vibration. Environment Catch running out oil and dispose of environmentally.

Fig. 156 l

Unscrew the level plug 1 (Fig. 156) at the bottom of the drum and fill in oil through the filler bore (2), until it starts to run out through the level bore.

For quality and quantity of oil refer to the table of fuels and lubricants. l

Screw the oil filler (2) and control plug (1) back in.

l

Repeat the oil change on the opposite side.

l

Check the oil level again at operating temperature (after running the vibration for approx. 0.5 hours).

Fig. 155 l

Move the drum until the drain plug 1 (Fig. 155) is in lowest position.

l

Unscrew the drain plug, drain all oil off and catch it.

l

Once the oil has run out clean the drain plug and screw it tightly back in.

BW 211/212/213 D-40

! Caution Overfilling causes overheating of the vibration bearings!

BOMAG

105

Every 1000 operating hours 5.30 Retighten the fastening of the axle on the frame

5.31 Tightening the wheel nuts

Fig. 158 Fig. 157 l

106

l

Check all fastening nuts on axle mounting bolts (Fig. 157) for tight fit.

BOMAG

Tighten the wheel nuts (Fig. 158) in a crosstype pattern.

BW 211/212/213 D-40

Every 1000 operating hours 5.32 Checking the ROPS i

5.33 Cleaning the oil bath air filter *

Note

On machines with a fitted cabin the ROPS (roll over protection structure) is integrated in the cabin. Please observe also the respective section in the safety regulations in this manual.

Fig. 160

Fig. 159

Check the cabin, especially the ROPS (Fig. 159) for cracks, corrosion, damage and missing fastening elements.

l

i

l

Loosen the quick locks (Fig. 160), take the filter bowl off and empty it.

l

Clean the filter mesh by repetitive dipping into diesel fuel.

l

Clean the filter bowl with diesel fuel and fill in engine oil up to the level mark.

l

reinstall the filter bowl.

Note

Unusual movements and noises (vibrations) during operation indicate damage or loose fastening elements. l

Check the fastening screws for the cabin (ROPS) to the operator's platform for tight fit.

l

Check the suspension buffers for the operator's stand for tight fit.

l

Check the condition and the fastening of the seat belt.

*

BW 211/212/213 D-40

BOMAG

Option

107


108

BOMAG

BW 211/212/213 D-40


5.34 Changing the hydraulic oil and the breather filter i

Note

See also section 5.1 "Notes on the Hydraulic System". Caution Apart from the normal oil change intervals the hydraulic oil must also be changed after major repairs in the hydraulic system. !

Fig. 161

Change the hydraulic oil only at operating temperature.

l

Unscrew the plug (Fig. 161) and drain the hydraulic oil off.

Clean the area around the hydraulic oil tank, the filler opening and the breather filter.

l

Check the sealing ring (1), replace if necessary and screw the plug tightly back in.

Do not use any detergents to clean the system. Do not start the engine after draining the hydraulic oil. Change the hydraulic oil filter element with every hydraulic oil change.

!

Danger

Danger of scalding! Danger of scalding by hot oil. Environment Catch running out oil and dispose of environmentally.

i

Fig. 162 l

Take the filler cap (Fig. 162) off.

l

Fill in hydraulic oil through the screen.

Note

The hydraulic oil filter element should only be changed after the test run.

i

Note

We recommend to use the filling and filtering unit (part-no. 079 930 35) with fine filter to fill the hydraulic system. This filters the hydraulic oil, prolongs the service life of the hydraulic oil filter and protects the hydraulic system. l

Check the oil level in the inspection glass.

Nominal value: approx. 3 cm below the upper edge of the inspection glass

BW 211/212/213 D-40

BOMAG

109

Every 2000 operating hours For quality and quantity of oil refer to the table of fuels and lubricants.

i

Note

The breather filter for the hydraulic tank is located in the filler cap and must therefore be replaced with the filler cap. l

5.35 Changing the hydraulic oil filter

Close the tank with the new filler cap.

!

Danger

Danger of scalding! There is a danger of scalding by hot oil when unscrewing the filter. Caution If the filter has to be changed together with the hydraulic oil, the filter should in any case be changed after the oil change and the test run. !

Do not use the oil in the filter bowl. Environment Catch running out oil, dispose of oil and filter element environmentally.

i

Note

The filter element must be changed with every hydraulic oil change and after major repairs in the hydraulic system.

Fig. 163 l

Unscrew the cap nut 4 (Fig. 163) and take the filter bowl (5) with the filter element (3) off.

l

Examine the sealing face on the filter element thoroughly for any visible dirt.

Caution Visible impurities can be an early indicator for a premature failure of system components and !

110

BOMAG

BW 211/212/213 D-40

Every 2000 operating hours a possible malfunction of parts. In such a case perform trouble shooting and, if necessary, replace or repair defective components. Negligance may damage the complete hydraulic system. Do not clean or reuse the filter element. l

Take the old filter element (3) out and clean the filter bowl and the thread.

l

Reinstall the filter bowl with the new filter element, check the condition of the O-rings (1) and (2), replace if necessary.

l

After a test run check the filter for leaks.

5.36 Changing the coolant !

Danger

Danger of scalding! Change the coolant only when the engine is cold. Environment Catch running out coolant and dispose of environmentally.

Fig. 164 l

Switch the shut-off valve for the cabin heater to "warm".

Fig. 165

BW 211/212/213 D-40

l

Unscrew the drain plug, drain all coolant off and catch it.

l

Screw the plug back in after all coolant has been drained off.

BOMAG

111


Fig. 166 l

Screw the lid off and fill in coolant up to the MAX-mark.

For quality of coolant refer to section 5.2, fuels and lubricants. l

Start the engine and run it up to operating temperature.

l

Allow the engine to cool down and check the coolant level again, top up if necessary.

112

BOMAG

BW 211/212/213 D-40


5.37 Checking the injection valves i

Note

This work must only be performed by authorized service personnel. The injection valves must be replaced every 12000 operating hours.

BW 211/212/213 D-40

BOMAG

113


114

BOMAG

BW 211/212/213 D-40

As required As r equired

5.38 Cleaning, changing the dry air filter cartridge !

Caution

Perform cleaning, maintenance and repair work only with the engine shut down. Do not start the engine after removing the filter element.

Fig. 168

Unclip three clamps on the housing cover and take off the cover (Fig. 168).

l

Fig. 167

Servicing of the dry air filter is necessary when the yellow piston (Fig. 167) has reached the inscription "Service" in front of a red background, but at the latest after 2 years. After completion of the filter service reset the indicator back to "Zero" by pressing the button.

Fig. 169

Pull the main filter element (Fig. 169) with light turning movements.

l

Removing the main filter element l

Fully open the engine hood.

Cleaning the main filter element !

Caution

If necessary, the main filter element may be cleaned up to five times. It must be renewed at the latest after a maximum utilization period of two years. The number of cleaning intervals of the main filter element can be marked on the safety element with a ball pen or a felt pen. Cleaning does not make sense if the main filter element is covered with a sooty deposit. Use a new filter cartridge.

BW 211/212/213 D-40

BOMAG

115

As required Cleaning the dust bowl

Incorrectly handled inserts may be ineffective because of damage (e.g. cracks) and cause damage to the engine. Replace the safety cartridge if the main filter element is defective! Additional cleaning intervals between two filter services signalized by the fault monitoring board are not necessary.

Fig. 171 l

Pull the internal part (Fig. 171) out and remove the dust from the cover.

l

Reinsert the inner part.

Caution When assembling the inner part make sure that the notch in the cover engages in the opening of the inner part. !

Fig. 170

i

Note

For cleaning purposes fit a tube to the compressed air gun (Fig. 170), the end of which should be bent for approx. 90°. The length should reach down to the bottom of the cartridge. Blow the cartridge out with compressed air (max. 5 bar) from inside to outside by moving the tube up and down inside the cartridge, until it if free of dust.

l

Examine the filter cartridge with a torch for cracks and holes in the paper bellows.

l

Installing the main filter element Slide the main filter element carefully into the housing.

l

When closing the housing cover the main filter element is automatically forced in the correct position. Reinstall the service covers.

l

Changing the safety filter element Caution The safety filter element must not be cleaned and should not be used again after it has been removed. !

Caution Do not continue to run the machine with a damaged main filter element. If in doubt use a new main filter element. !

Break the seal only to replace the safety filter element. The safety filter element must be replaced: if the main filter element is defective, after five service intervals of the filter cartridge, at the latest after 2 years,

116

BOMAG

BW 211/212/213 D-40

As required if the warning light comes on again after servicing the main filter cartridge. Remove the housing cover and pull the main filter element off.

l

smooth drum only

Fig. 172

Fig. 173

Perforate the seal of the safety filter element from inside to outside using a suitable tool (Fig. 172) and pull both latches up.

l

Grip the safety element by both latches and pull it out with slight turning movements.

l

l

Push in a new safety filter element.

l

Reassemble main filter element and cover.

Caution Make sure that the cover locks engage correctly. !

5.39 Adjusting the scrapers

l

Check the condition and adjustment of the front and rear scrapers, adjust or replace the scraper rubber if necessary.

l

To adjust the scrapers 1 (Fig. 173) loosen the fastening screws (2) in the slots and push the scraper bracket towards the drum until the scraper touches.

l

Retighten the fastening screws.

padfoot drum only

Fig. 174

BW 211/212/213 D-40

l

Check condition and adjustment of scrapers 2 (Fig. 174), adjust or replace the teeth if necessary.

l

To adjust the scrapers (2) slacken the fastening screws (1) in the slots and move the scrap-

BOMAG

117

As required er towards the drum, leaving a gap of approx. 25 mm. l

5.40 Adjusting the parking brake

Retighten the fastening screws. ! Caution Have adjustment work on the brake performed by a specialist! Always adjust both sides.

l

Secure the machine with chocks against unintentional rolling.

l

Start the diesel engine to release the brake.

Fig. 175 l

Unlock the travel lever (Fig. 175) by pushing it to the left, but do not actuate it to position "I" or "II".

The parking brake is released

Fig. 176

118

l

Unscrew the locking plate 2 (Fig. 176).

l

Turn the square (1) in anti-clockwise direction against the end stop.

BOMAG

BW 211/212/213 D-40

As required 5.41 Changing the tires !

Danger

Danger of accident! Observe all safety notes for the lifting of loads. l

Place a jack (min. 5 t bearing capacity) under the rear frame and jack the machine up so that the wheel can turn freely.

l

Unscrew the wheel nuts and take the wheel off.

Fig. 177 l

To adjust the clearance turn the square 1 (Fig. 177) three revolutions back in clockwise direction.

l

Screw the locking plate back on.

l

Pull the plug off the brake valve and try to drive.

The machine must be braked.

Fig. 178

BW 211/212/213 D-40

l

Attach the wheel (Fig. 178) and tighten the wheel nuts crosswise with 550 Nm (405 ft. lb.).

l

Check the tire pressure, see technical data.

BOMAG

119

As required 5.42 Changing the fresh air filter in the cabin

5.43 Tightening torques

Fig. 180

Fig. 179 l

l

Unscrew the fastening screws for the filter bracket (Fig. 179) and take the filter out. Insert the new filter and reassemble the filter bracket.

* Strength classes for screws with untreated, nonlubricated surface. Screw quality designations are stamped on the screw heads. 8.8 = 8G 10.9 = 10K 12.9 = 12K Axle - frame

l

M 22x1.5

= 710 Nm

Wheel nuts

l

M 22x1.5

= 550 Nm

The values result in a 90% utilization of the screw yield point at a coefficient of friction μ total = 0,14. When using lubricant MOS2 the specified tightening torques do not apply.

i

Note

Self-locking nuts must always be replaced once they have been unscrewed.

120

BOMAG

BW 211/212/213 D-40

As required 5.44 Engine conservation If the engine is to be shut down for a longer period of time (e.g. over winter), please consult the service department of the engine manufacturer for further details.

BW 211/212/213 D-40

BOMAG

121

As required

122

BOMAG

BW 211/212/213 D-40

6 Trouble shooting

BW 211/212/213 D-40

BOMAG

123

Trouble shooting 6.1

General notes

The following work must only be carried out by qualified and trained personnel or by the sales service. Please observe strictly the safety regulations in chapter 2 of these operating and maintenance instructions. Faults occur frequently due to the fact, that the machine has not been properly operated or serviced. Therefore, whenever a fault occurs, read through these instructions on correct operation and maintenance. If you cannot locate the cause of the fault or eliminate it yourself by following the trouble shooting charts, you should contact our customer service departments at our branch office or dealers. Danger Danger of injury! !

Keep away from rotating parts of the engine.

124

BOMAG

BW 211/212/213 D-40

Trouble shooting 6.2

Engine

Faults

Possible cause

Remedy

The engine does not start

Starter defective or pinion not engaging

Have examined by a specialist

Fuel tank empty

Fill and bleed the tank

Temperature below starting limit

Use winter fuel and engine oil acc. to the ambient temperature.

Fuel filter clogged, in winter due to paraffin separation.

Change the filter. use winter fuel

Fuel lines leaking

Check all line connections for leakages and tighten the fittings.

Battery discharged or not connected

Tighten the pole clamps, check the cable connections

Injection valves or injection pump defective


Battery power too low, battery clamps loose or oxidized, causing the starter to turn too slowly

Have the battery checked, clean the terminal clamps, tighten them and cover them with acid free grease

Especially during winter: the use of too viscous engine oil

Use engine oil suitable for the ambient temperature

Fuel supply restricted, in winter fuel system clogged due to paraffin separation

Change the fuel filter. Check the line connections for leaks and tighten the fittings. Use winter fuel in the cold season.

Incorrect valve clearance

Adjust the valve clearance

Injection valve defective


Injection lines leaking

Check the lines for leakages

Turbo charger defective


Dry air filter dirty

clean, replace if necessary

Excessive play in the throttle cable

Adjust the throttle cable, change it if necessary

The engine starts poorly and works irregularly with poor power

BW 211/212/213 D-40

BOMAG

125

Trouble shooting Faults

Possible cause

Remedy

Excessive exhaust smoke

Engine oil level too high

Drain the oil to the upper dipstick mark


clean, replace if necessary

Exhaust gas turbo-charger defective


Poor compression due to burned or broken compression rings or incorrect valve clearance

Have compression rings and pistons examined by a specialist, adjust the valve clearance



Cooling fins on radiator extremely soiled (the warning light "engine oil temperature" lights)

Clean the cooling fins



Engine oil level too low

Top up engine oil to the upper dipstick mark

Filling capacity of the injection pump not correctly adjusted

Have adjusted by a specialist

Cooling air flow restricted

Clean the cooling air duct

V-belt loos or broken

Tension or replace the V-belt

Engine oil level too high

Drain the engine oil down to the upper dipstick mark


clean, change if necessary

Exhaust gas turbo-charger defective


Charge air hose leaking

Check fastening and connections





Engine oil level too low (control light "engine oil pressure" lights, the warning buzzer sounds)

Top up oil

Leakages in the lubrication system

Shut the engine down immediately, check fittings on oil lines, lubrication oil filter and oil cooler for leaks, if necessary tighten the fittings.

Generator speed too low

Check the V-belt tension, replace the Vbelt if necessary

The generator does not charge the battery, because generator or regulator is defective

Have examined by a specialis

Engine overheats, shut down immediately!

Poor engine power

Engine oil pressure too low

The charge control light lights during operation, the warning buzzer sounds

126

BOMAG

BW 211/212/213 D-40

Trouble shooting

BW 211/212/213 D-40

BOMAG

127

Trouble shooting

128

BOMAG

BW 211/212/213 D-40

BW211-212D-40 Operation Instruction E 04.2008 00815881.d08.pdf

Recommend Documents