Analysis Beam on Elastic FoundationDescripción completa
bidang enginnering
• To determine the compressive strength of the wooden cubes • To observe the anisotropic behavior of the wood. • To determine the modulus of elasticity and modulus of stiffness.Deskripsi lengkap
woodFull description
beamFull description
analisis
Beam
Flexural or Bending Test Complete Lab ReportDeskripsi lengkap
Flexural or Bending Test Complete Lab Report
One of the factors in assessing the applicability of wire or cable on the lunar surface is its flexibility under extreme cold conditions. Existing wire specifications did not address their …Descrição completa
Flexural or Bending Test Complete Lab ReportFull description
REality Bending
Full description
Description complète
Bending WoodFull description
6. To Perform Perform Bending Test Test on Wooden Beam (26-11-2008) Apparatus 10 ton Buckton UTM, Deflection Gauges, Wooden Beam, Measuring Tape
Objective •
•
To study the bending or flexural behavior of the beam To determine the Modulus of Elasticity and Modulus of Rupture of the wood.
Related Theory Shear Force The sum of all the forces acting perpendicular to the section or forces which tend to slides two part of the section on each other.
Elastic Curve A line representing the deformed form of the center line of the beam is known as Elastic Curve.
Flexural Stress Stresses produced by the bending moment is known as Flexural Stress.
Stresses Internal resistance of the material against loading is known as Stress.
Flexural Equation It is the fundamental relationship between the Bending moment and geometry of deformation.
Flexural Formula It gives a relationship in bending moment and flexural stresses.
Modulus of Rupture •
•
It is the energy absorbed per unit volume when the specimen is loaded from zero to failure. It is the maximum tensile stress which can be developed in the beam before failure. 1 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73
Adil Ad il
Difference between Modulus of Rupture & Modulus of Toughness •
•
Modulus of Toughness can be determined by tension or compression test (axial tests) and it is for any type of member. But Modulus of Rupture is only for a member having flexural or bending.
Loading Arrangement for Experiment Loading arrangement for this certain experiment is “Two point Arrangement”. This is to produce only bending, it will not cause any shear force in the beam.
Two point Arrangement Two equal loads acting at the equal distance from the supports is known as two point loading system. In such a system the shear force acting between the loads l oads
2 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73
Adil Ad il
is zero and bending moment between the loads is constant
3 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73
Adil Ad il
Load is being applied on wooden bean in 10ton Buckton UTM
Wooden Beam after the Fracture
Procedure 1. First of all measure the breath and height of the wooden sample 2. 3. 4. 5.
through the measuring tape. Fix the wooden beam sample in 10 ton Buckton UTM. Fix the dial gauges under the beam as shown figure the figure above, according to the distances shown. Now apply the load gradually on the beam and note down the amount of deflection against each loading. Note down all the deflection up to failure of specimen and finally find the Modulus of Elasticity, Modulus of Rupture from their respective formulae.
Precautions 1. Apply the loads gradually so that we can read the deflection against
each reading easily. 2. Remove the gauges before the failure load, otherwise they may get damages. 4 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73
Adil Ad il
3. Stay away from the machine or otherwise the particles may hurt
5 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73
Adil Ad il
Calculations of Modulus of Rupture and Modulus of Elasticity b= 50 mm, mm, h= 50 50mm mm,,
l=10 l=1000 00mm mm
Breaking Load (Pmax):
1.15 tons = 11281.5 N
Modulus of Rupture =
=
Modulus of Elasticity = Slope of Straight line in graph i.e.
= 1534.4
Comments Wooden beam should be fracture symmetrically from the both sides because we have applied symmetrical load by Two Point Load System, but we can see from the sketch of wooden beam after fracture, it did not fracture in that manner. This can be due to some weakest plane in the way of fracture. On the right side of the beam it fractured perfectly.
6 Bendi Bending ng Test Test on wood wooden en Beam Beam Javed 07Civil73