AS-11.65.051_main_fr_KDL16S

KONE KSS 280 Series Signalization Maintenance instruction

REPAIR INSTRUCTION FOR KONE KSS 280 SERIES SIGNALIZATION

D

t f ra

© 2012 KONE Corporation KONE KSS 280 Maintenance 2013-05-02 (A) AS-12.20.027 instruction Series Signalization

All rights reserved.

© 2012 KONE Corporation All rights reserved.

1 (78)

AS-12.20.027 (A) 2013-05-02


TABLE OF CONTENTS 1

ABOUT THIS DOCUMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Purpose of this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Signs and symbols used in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

KSS 280 SERIES SIGNALIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3

SAFETY AND MAINTENANCE TARGETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Maintenance method safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Basic rules preventing ESD hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Environmental Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Customer experience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 14 14 14 15

4

REPLACING LANDING COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Safety measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Connecting the ESD wrist strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Replacing landing components, buttons and key switches . . . . . . . . . . . . . . . . . . . .

16 16 16 17 18

5

REPLACING COP COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Safety measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 KSS-L multiboard (KSSLMUL) replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 KSSFRE board replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 Key switch replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7 COP button assembly (KSSLCBBX) replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8 COP pressel replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 25 25 25 27 35 42 49 56

6

CONFIGURING AND TESTING KSS 280 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Accessing maintenance mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Configuring COP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Testing COP and landing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64 64 64 67 72

7

ADJUSTING GONG VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

8

COP SOFTWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

9

APPROVALS AND VERSION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

10

FEEDBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

D


t f ra

2 (78)

3 3 3 3 4 6

AS-12.20.027 (A) 2013-05-02


1

ABOUT THIS DOCUMENT

1.1

Purpose of this document This document describes how to replace, test and configure KSS 280 signalization components.

1.2

Audience

D

t f ra

This document is intended to be used by people who are familiar with elevator maintenance and installation and have received proper training on methods and safety as specified by KONE.

1.3

Abbreviations COP

Car Operating Panel

DOB

Door Open Button

ESD

Electrostatic Discharge

LCE

Lift Controller and Electrification

PCB

Printed Circuit Board

RDF

Recall Drive Feature

LCS

Landing call station


3 (78)

AS-12.20.027 (A) 2013-05-02


1.4

Signs and symbols used in this document Warning signs are typically used in places where a safety hazard may exist. The cause of hazard can be, for example, machine, tool, equipment, unprotected roof edge or work activity. Sign

Description General warning sign

t f ra

Risk of electro-static discharge

D

Mandatory signs are typically used in places where an action is mandatory, for example wearing protective equipment or switching electrical power off. Sign

Description Turn main power switch off.

Lock and tag the main switch.

Wear safety gloves.

Remove the screw.

Loosen the screw. Do not remove it.


4 (78)

AS-12.20.027 (A) 2013-05-02


Sign

Description Tighten the screw to full tightness.

t f ra Unplug.

D


Connect.

5 (78)

AS-12.20.027 (A) 2013-05-02


1.5

Related documents For more information see: – AM-01.03.002 Take 5 - Electrical safety when working on elevators, escalators and autowalks – AM-12.20.005 KONE signalization system (KSS) installation – AR-12.20.026 KSS 280-Series signalization – AS-01.01.004 Take care, end user safety focal points in elevator maintenance – AS-01.03.101 On-site maintenance safety manual – AS-12.02.001 Instruction for handling ESD sensitive devices – SO-10.15.001 Elevator features

D


t f ra

6 (78)

AS-12.20.027 (A) 2013-05-02


2

KSS 280 SERIES SIGNALIZATION Cables with diameters from 0.32 mm (AWG 28) to 1.3 mm (AWG 16) are suitable for all connectors.

Hall indicators Hall lantern

Car operating panels Hall display

3004583.wmf

KSH 280

D

3004584.wmf

KSI 286 Landing call stations

t f ra 3004518.wmf

3004517.wmf

KSJ 280

KSJ 290 (NA)

3004519.wmf

3004586.wmf

3004520.wmf

3004588.wmf

KSL 280

KSL 281


3004589.wmf

KSL 284 KSF 284 (NA) 7 (78)

3004614.wmf

KSL 286

KSC 296, KSC 286 AS-12.20.027 (A) 2013-05-02


Table 1: Hall lantern assembly Illustration 1. 2. 3. 4. 5. 6.

D

Description Faceplate assembly Speaker Control board Back plate Mounting bracket Fixing screw (optional)

t f ra

Table 2: Hall lantern indicator assembly Illustration 1. 2. 3. 4. 5. 6.


8 (78)

Description Faceplate assembly Speaker Control board Back plate Mounting bracket Fixing screw (optional)

AS-12.20.027 (A) 2013-05-02


Table 3: Landing call station assembly - Simplex Illustration KSL280

1

2

1. 2. 3. 4. 5. 6.

D 4

Description Buttons Lens assembly Button spring Control board Back plate Mounting bracket

t f ra 6

5

3 3010169.wmf


9 (78)

AS-12.20.027 (A) 2013-05-02


Illustration KSL284

1

1. 2. 3. 4. 5. 6.

2

D 3

Description Buttons Key switch Lens assembly Control board Back plate Mounting bracket

t f ra

4

6

5

3010173.wmf


10 (78)

AS-12.20.027 (A) 2013-05-02


Illustration KSL281

1

1. 2. 3. 4. 5.

D 2

Description Buttons Lens assembly Control board Back plate Mounting bracket

t f ra 5

3

4

3010171.wmf


11 (78)

AS-12.20.027 (A) 2013-05-02


Table 4: Landing call station assembly - Duplex Illustration KSL281 - Duplex

1

D

t f ra

1. 2. 3. 4. 5.

Description Buttons Lens assembly Control board Back plate Mounting bracket

5

4

3

2

3010172.wmf


12 (78)

AS-12.20.027 (A) 2013-05-02


Illustration KSL286- Duplex

1

D 2


t f ra

3

1. 2. 3. 4. 5. 6.

Description Buttons Key switches Lens assembly Control board Back plate Mounting bracket

6

4

5

3010174.wmf

13 (78)

AS-12.20.027 (A) 2013-05-02


3

SAFETY AND MAINTENANCE TARGETS Refer to AS-01.03.101On-site Maintenance Safety Manual for general safety precautions and personal safety issues.

3.1

Maintenance method safety

t f ra

Note the following safety items when working with KSS 280 series signalization: – General KONE safety regulations must be followed during the work. All normal safety measures required in elevator maintenance must be implemented. Local safety regulations must also be followed. – Refer to AM-01.03.002 Take 5 - Electrical safety when working on elevators, escalators and autowalks. The Take 5 safety initiative is designed for installation, servicing, maintenance and modernisation work done on the elevators.

3.2

D

Basic rules preventing ESD hazards

1. Disconnect all power supplies. 2. Earth yourself before touching components. 3. Do not unpack the spare parts before installation. 4. Do not touch the components on the board unnecessarily. 5. Hold the PC-board from its edges. 6. The old component must be handled in the same way as the new one. 7. Do not wear combinations of clothing that can create static charges. Refer to AS-12.02.001.

3.3

Environmental Issues Hazardous waste material must be taken care of according to the local regulations and KONE Environmental Strategy. Refer to AS-01.01.190 Environmental excellence-Maintenance for more information on environmental issues.


14 (78)

AS-12.20.027 (A) 2013-05-02


3.4

Customer experience The focus of your work must always be customer satisfaction. To reach and exceed the customers’ expectations, be polite, constructive and co-operative, and communicate clearly. Remember that for customers, you represent KONE, so ensure that you handle or at least communicate all customer requests and feedback to the correct persons. For more information on how to deliver best-in-class customer experiences through behavior and communication, see the KONE Ambassador program in KONE intranet (search for Ambassador) or contact your supervisor.

D


t f ra

15 (78)

AS-12.20.027 (A) 2013-05-02


4

REPLACING LANDING COMPONENTS

4.1

Tools Use standard maintenance tools.

4.2

Safety measures

D

t f ra

Step Action 1 Take the elevator out of use.

2 3

Illustration/Note Travel in the car to the floor with MAP or machine room (control cabinet). Inform the building users with maintenance signs or stickers according to local practises. Place warning and information signs and safety fences as required.

Ensure that nobody is in the elevator car. Switch off the main power. Lock and tag the main switch.


16 (78)

AS-12.20.027 (A) 2013-05-02


4.3

Connecting the ESD wrist strap This section describes discharging the static charge through the ESD wrist strap to the earthing point. Step Action Illustration/Note 1 Place the working pad on the working area. 2 Connect the crocodile clip at the end of See the picture below. the cable to the earthing point. 3 Attach the wrist strap around your wrist. Ensure that the wrist strap makes good contact with your skin. 4 Connect the wrist strap to the press stud on the work pad.

D

t f ra 3010230.wmf


17 (78)

AS-12.20.027 (A) 2013-05-02


4.4

Replacing landing components, buttons and key switches Replace landing call station buttons only with similar buttons. You do not need to reconfigure the signalization after any landing component replacement. Step 1

Action

D

Note / Illustration

t f ra

3004526.wmf

3010313.wmf

NOTE! Allen screw (size 2.5 mm) is optional.

3010170.wmf

Allen screw size: 2.5 mm


18 (78)

AS-12.20.027 (A) 2013-05-02


Step 2

Action

Note / Illustration

t f ra 3004530.wmf

3

D

3004531.wmf

3004532.wmf

3004533.wmf


19 (78)

AS-12.20.027 (A) 2013-05-02


Step 4

Action

Note / Illustration

NOTE! Do not damage the components or surroundings.

t f ra 3004534.wmf

D

3004535.wmf

3004536.wmf

3004537.wmf


20 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 5 Replace the damaged part with a new part.

D

Note / Illustration

t f ra

3010168.wmf

CAUTION! If you are replacing the buttons, carefully twist the buttons to remove them from the mid part.


21 (78)

AS-12.20.027 (A) 2013-05-02


Step 6

Action

Note / Illustration

t f ra 3004544.wmf

7

D

3004543.wmf

3004591.wmf

3004545.wmf

8

3004546.wmf

3004547.wmf


22 (78)

AS-12.20.027 (A) 2013-05-02


Step 9

Action

Note / Illustration

t f ra

3004548.wmf

D

3010166.wmf

NOTE! Verify that the plastic clip locks the display. The screw is optional with hall lanterns.

3004551.wmf

10

Remove the ESD kit.


23 (78)

AS-12.20.027 (A) 2013-05-02


5

REPLACING COP COMPONENTS Illustration

2 3

4

D

Description 1. Back plate 2. KSS-L multiboard (KSSLMUL) 3. Display 4. Cabinet panel 5. Button faceplate 6. Button assembly (KSSLCBBx) 7. KSSLFRE board

t f ra 1

7

5

6


3004554.wmf

24 (78)

AS-12.20.027 (A) 2013-05-02


5.1

Tools – – – –

5.2

Standard maintenance tools Allen key, 3 mm Screwdriver, Phillips Work stool, KM265173

Safety measures

t f ra

Follow the KONE and local safety regulations.

5.3

Preparations

D

It is recommended to perform the maintenance work at the nearest floor to the MAP or machine room (control panel), because the power must be switched on / off during the maintenance work. Step Action 1 Take the elevator out of service.

2 3 4 5

Illustration/Note Travel in the car to the floor with MAP or machine room (control cabinet). Inform the building users with maintenance signs or stickers according to local practises. Place warning and information signs and safety fences as required.

Ensure that nobody is in the elevator car. Switch RDF on. Drive the car to suitable level for accessing the car roof. Switch off the main power. Lock and tag the main switch.


25 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 6 Open the landing doors and disconnect the car roof emergency battery.

D 7 8 9 10

Illustration/Note

t f ra 3010231.wmf

Close the landing doors and ensure that they are locked properly. Switch on the main power. Drive the elevator back to floor level with RDF and open the doors. Switch off the main power. Lock and tag the main switch.


26 (78)

AS-12.20.027 (A) 2013-05-02


5.4

KSS-L multiboard (KSSLMUL) replacement

5.4.1

Lifting COP from wall Step Action 1 Open the security fixing screw. 2 Slide the COP out of the fixing bracket by lifting it up.

Illustration/Note

t f ra

CAUTION! Do not damage the cables.

D

3004556.wmf 3004555.wmf


27 (78)

AS-12.20.027 (A) 2013-05-02


5.4.2

Connecting ESD wrist strap This section describes discharging the static charge through the ESD wrist strap to the earthing point. Step Action Illustration/Note 1 Place the working pad on the working area. 2 Connect the crocodile clip at the end of See the picture below. the cable to the earthing point. 3 Attach the wrist strap around your wrist. Ensure that the wrist strap makes good contact with your skin. 4 Connect the wrist strap to the press stud on the work pad.

D

t f ra 3010232.wmf


28 (78)

AS-12.20.027 (A) 2013-05-02


5.4.3

Opening the COP Step Action 1 Disconnect the COP cables.

2 3

4

Illustration/Note

t f ra

Place the COP horizontally on a flat surface (work stool). Loosen the side screws and remove the cabinet panel.

D

3004557.wmf

Release the locking of upper and button faceplate.

3004558.wmf

5

Remove the button faceplate. CAUTION! Open the button faceplate carefully and unplug the cables from the connectors. The cables are short. Do not damage the cables. 3010233.wmf

6

Unscrew (*) and remove the display.

*

3004560.wmf


29 (78)

AS-12.20.027 (A) 2013-05-02


5.4.4

Replacing KSS-L multiboard (KSSLMUL) Step Action 1 Disconnect all KSSLMUL cables.

2 3

D

Note / Illustration Mark the cable positions if required.

t f ra

3010234.wmf

Unscrew and remove the KSSLMUL board. Install the new KSSLMUL board with screws.

3004562.wmf

* 3004561.wmf

Ensure the correct alignment of the KSSMUL end resistor and jumper connectors through the back plate hole (*). CAUTION! Electrostatic discharge (ESD) can damage the drive board. For more information on working with ESD sensitive device, see AS-12.20.001.


30 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 4 Connect the cables.

5.4.5

Closing the COP

D

Note / Illustration

t f ra

Step Action 1 Install the display to the back plate with screws (*), if removed.

3010235.wmf

Illustration/Note Route the cables to the button section so they are not caught between the parts.

*

3010236.wmf


31 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 2 Connect the button board cables.

3

t f ra

Install the button faceplate.

D

Illustration/Note

3010237.wmf

Ensure that the cables are not caught between the parts.

3004568.wmf

4

Tighten the top and bottom screws to lock the upper and button faceplate in place.

3004570.wmf


32 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 5 Install the cabinet panel and tighten the side screws to lock it in place.

6

D

Lift the COP on car wall.

Illustration/Note CAUTION! Tighten the screws carefully. The screw counterpart inside the COP breaks easily.

t f ra

3004571.wmf

3004572.wmf

7

Connect the COP cables.

8 9

Remove the ESD kit. Slide the COP on the fixing bracket by pushing it down. Tighten the security fixing screw.

10


33 (78)

AS-12.20.027 (A) 2013-05-02


5.4.6

Returning elevator to service Step Action 1 Switch on the main power. 2 3

4

Illustration/Note The system copies the COP configuration to the replaced part(s) automatically.

Move the car with RDF to suitable level for accessing the car roof. Switch off the main power. Lock and tag the main switch.

D

t f ra

Open the landing door and connect the car roof emergency battery. Connect wires (red to plus, blue to minus). CAUTION! Wrong connection will destroy the LCECCB board.

3010243.wmf

5 6 7 8 9

10

Close the landing doors and ensure that they are locked properly. Switch on the main power. Drive the elevator back to floor level with RDF and open the doors. Switch RDF off. Test that all components work correctly: – If the button board is replaced, check that the elevator serves all levels with COP buttons. – If the KSSLMUL is replaced, verify the display operation and floor markings (perform section 6.4 Testing COP and landing components) and check that the elevator serves all levels with COP buttons. Return the elevator to service.


34 (78)

If the configuration is missing (COP does not operate correctly), switch the main power off and back on to recopy the configuration. For more information on how to manually copy the configuration, see section 6.3 Configuring COP.

AS-12.20.027 (A) 2013-05-02


5.5

KSSFRE board replacement

5.5.1

Lifting COP from wall Step Action 1 Open the security fixing screw. 2 Slide the COP out of the fixing bracket by lifting it up.

Illustration/Note

t f ra


D

3004556.wmf 3004555.wmf


35 (78)

AS-12.20.027 (A) 2013-05-02


5.5.2


D

t f ra 3010232.wmf


36 (78)

AS-12.20.027 (A) 2013-05-02


5.5.3


2 3

4

Illustration/Note

t f ra


D

3004557.wmf


3004558.wmf

5



37 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 6 Unscrew (*) and remove the display.

Illustration/Note

*

5.5.4

D

Replacing KSSFRE board

Step 1 2 3 4

t f ra

Action Disconnect all the KSSLFRE cables. Remove the KSSLFRE board. Install the new KSSLFRE board. Connect the cables.

3004560.wmf

Note / Illustration Mark the cables.

3010164.wmf


38 (78)

AS-12.20.027 (A) 2013-05-02


5.5.5

Closing the COP Step Action 1 Install the display to the back plate with screws (*), if removed.

2

D


t f ra

*

3010236.wmf

Connect the button board cables.

3010237.wmf

3



3004568.wmf


39 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 4 Tighten the top and bottom screws to lock the upper and button faceplate in place.

5

t f ra

Install the cabinet panel and tighten the side screws to lock it in place.

D

Illustration/Note

3004570.wmf

CAUTION! Tighten the screws carefully. The screw counterpart inside the COP breaks easily.

3004571.wmf

6


3004572.wmf


40 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 7 Connect the COP cables.

8 9 10

5.5.6

Illustration/Note


Returning elevator to service

D

t f ra

Step Action 1 Switch on the main power. 2 3

4




3010243.wmf

5 6 7 8

Close the landing doors and ensure that they are locked properly. Switch on the main power. Drive the elevator back to floor level with RDF and open the doors. Switch RDF off.


41 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 9 Test that all components work correctly: – If the button board is replaced, check that the elevator serves all levels with COP buttons. – If the KSSLMUL is replaced, verify the display operation and floor markings (perform section 6.4 Testing COP and landing components) and check that the elevator serves all levels with COP buttons. 10 Return the elevator to service.

D

5.6

Key switch replacement

5.6.1

Lifting COP from wall

Illustration/Note If the configuration is missing (COP does not operate correctly), switch the main power off and to recopy the configuration. For more information on how to manually copy the configuration, see section 6.3 Configuring COP.

t f ra

Step Action 1 Open the security fixing screw. 2 Slide the COP out of the fixing bracket by lifting it up.

Illustration/Note


3004556.wmf 3004555.wmf


42 (78)

AS-12.20.027 (A) 2013-05-02


5.6.2


D

t f ra 3010232.wmf


43 (78)

AS-12.20.027 (A) 2013-05-02


5.6.3


2 3

4

Illustration/Note

t f ra


D

3004557.wmf


3004558.wmf

5


6

Unscrew (*) and remove the display.

*

3004560.wmf


44 (78)

AS-12.20.027 (A) 2013-05-02


5.6.4

Replacing key switches Step Action Note / Illustration 1 Disconnect the keyswitch cable from the Mark the connector. KSSLFRE board. 2 Unscrew the keyswitch ring and remove the keyswitch. 3 Install the new keyswitch. 4 Connect the cable to KSSLFRE.

D


t f ra

45 (78)

3010164.wmf

AS-12.20.027 (A) 2013-05-02


5.6.5


2

D


t f ra

*

3010236.wmf


3010237.wmf

3



3004568.wmf


46 (78)

AS-12.20.027 (A) 2013-05-02



5

t f ra


D

Illustration/Note

3004570.wmf


3004571.wmf

6


3004572.wmf


47 (78)

AS-12.20.027 (A) 2013-05-02



8 9 10

5.6.6

Illustration/Note



D

t f ra


4




3010243.wmf

5 6 7 8



48 (78)

AS-12.20.027 (A) 2013-05-02



D


t f ra

5.7

COP button assembly (KSSLCBBX) replacement

5.7.1



Illustration/Note


3004556.wmf 3004555.wmf


49 (78)

AS-12.20.027 (A) 2013-05-02


5.7.2

Connecting ESD wrist strap This section describes discharging the static charge through the ESD wrist strap to the earthing point. Step Action Illustration/Note 1 Place the working pad on the working area. 2 Connect the crocodile clip at the end of See picture below. the cable to the earthing point. 3 Attach the wrist strap around your wrist. Ensure that the wrist strap makes good contact with your skin. 4 Connect the wrist strap to the press stud on the work pad.

D

t f ra 3010232.wmf


50 (78)

AS-12.20.027 (A) 2013-05-02


5.7.3


2 3

4

Illustration/Note

t f ra


D

3004557.wmf

Release the locking of the button faceplate.

3010302.wmf

5



51 (78)

AS-12.20.027 (A) 2013-05-02


5.7.4

Replacing COP button assembly (KSSLCBBX) Step Action 1 Unscrew and remove the button assembly.

2

D

Note / Illustration

t f ra

3004563.wmf

Install the new button assembly and tighten the screws.

CAUTION! Electrostatic discharge (ESD) can damage the drive board. For more information on working with ESD sensitive device, see AS-12.20.001.


52 (78)

AS-12.20.027 (A) 2013-05-02


5.7.5


D


t f ra

*

3010236.wmf

2


3


3010237.wmf


3004568.wmf


53 (78)

AS-12.20.027 (A) 2013-05-02



5

t f ra


D

Illustration/Note

3004570.wmf


3004571.wmf

6


3004572.wmf


54 (78)

AS-12.20.027 (A) 2013-05-02



8 9 10

5.7.6

Illustration/Note



D

t f ra


4




3010243.wmf

5 6 7 8



55 (78)

AS-12.20.027 (A) 2013-05-02



D

5.8

COP pressel replacement

5.8.1



t f ra


Illustration/Note


3004556.wmf 3004555.wmf


56 (78)

AS-12.20.027 (A) 2013-05-02


5.8.2


D

t f ra 3010232.wmf


57 (78)

AS-12.20.027 (A) 2013-05-02


5.8.3


2 3

4

Illustration/Note

t f ra


D

3004557.wmf

Release the locking of the button faceplate.

3010302.wmf

5



58 (78)

AS-12.20.027 (A) 2013-05-02


5.8.4

Replacing COP pressels Step Action 1 Unscrew and remove the button assembly.

Note / Illustration

t f ra

CAUTION! Electrostatic discharge (ESD) can damage the drive board. For more information on working with ESD sensitive device, see AS-12.20.001.

2

D

3004564.wmf

Replace the COP pressel using a small screw driver. NOTE! Do not drop the spring under the pressel.

3004566.wmf


59 (78)

3004565.wmf

AS-12.20.027 (A) 2013-05-02


5.8.5


D


t f ra

2


3


*

3010236.wmf

3010237.wmf


3004568.wmf


60 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 4 Tighten the top ( if removed) and bottom screws to lock the upper and button faceplate in place.

5

t f ra


D

Illustration/Note

3004570.wmf


3004571.wmf

6


3004572.wmf


61 (78)

AS-12.20.027 (A) 2013-05-02



8 9 10

5.8.6

Illustration/Note



D

t f ra


4




3010243.wmf

5 6 7 8



62 (78)

AS-12.20.027 (A) 2013-05-02



D



t f ra

63 (78)

AS-12.20.027 (A) 2013-05-02


6

CONFIGURING AND TESTING KSS 280 Configure and test the signalization with the COP maintenance mode (indicated by T or C). Maintenance mode contains: – Test menu (“T”) – Configuration menu (“C”)

6.1

Tools No tools needed.

6.2

D

t f ra

Accessing maintenance mode

Step Action 1 Press DOB button and the lower / leftmost call button on the COP for ten seconds until “Spanner” icon starts to blink.


64 (78)

Note / Illustration

AS-12.20.027 (A) 2013-05-02


Step Action 2 Press the lower/leftmost call button for five seconds until: – "Spanner" icon stops blinking and continues to stay on. – "--" sign appears right side of the "Spanner" icon. – "T" sign appears on the leftmost position of the indicator.

3

D

Note / Illustration Maintenance mode is accessed.

t f ra

Press the lower/leftmost call button to toggle between Test (T) and Configuration (C) menu.


65 (78)

AS-12.20.027 (A) 2013-05-02


Step Action 4 Press DOB shortly to enter either "T" or "C" menu.

D


Note / Illustration

t f ra

66 (78)

AS-12.20.027 (A) 2013-05-02


6.3

Configuring COP Re-configuration is necessary when: – Adding, replacing or removing components to the COP panel – Changing or adding an option or floor in the system Table 5: Configuration codes Code 00 01 02

6.3.1

t f ra

Name Re-configure button Re-configure COP Clear all the configuration

D

Configuration overview

Description Re-configure a single button or switch Re-configure the whole COP (Side) Clear all the configurations stored in KSSLCBBx and KSSLMUL (the COP must be re-configured from scratch).

Each COP button and switch has its own ID number for elevator LON network. The signalization system identifies each COP button and switch by their individual ID number. The ID numbers of COP buttons and switches are stored in the configuration table located on the KSSLMUL board.


67 (78)

AS-12.20.027 (A) 2013-05-02


Table 6: COP configuration example Car call button 0 1 2 4 Dummy floor 6 7 8 9 10 DOB DCB PIN code OSS key switch PRC key switch Car Call locking Group 1 switch FRD switch ATC switch OCL switch OCV switch

D

ID code for LON 1 2 3 5 7 8 9 10 11 113 114 117 217 219 193 193 223 225 227

t f ra

Landing buttons do not have ID numbers and cannot be reconfigured.


68 (78)

AS-12.20.027 (A) 2013-05-02


6.3.2

Using configuration menu (C) In configuration menu, the two digit configuration codes appear on the right side of the "Spanner" icon starting from 00. Step Action 1 Press the lower/leftmost call button shortly to increase the configuration code by one unit.

D 2

Note / Illustration Reset back to 00 when sub-menu code is greater than 02.

t f ra

Press the DOB button shortly to enter the selected configuration sub-menu.


69 (78)

AS-12.20.027 (A) 2013-05-02


6.3.3

Configuring COP button or switch Step Action 1 In configuration sequence 00, press the COP button or cycle key/toggle switch shortly: • The floor/feature ID (2 digits) is displayed on the right side of the "Spanner" icon.

2

3

D

Note / Illustration Pressing the COP button shortly under reconfiguration, shows the logic floor ID.

t f ra

* 00 Button / Key switch not configured / dummy 01 Logic floor 1 02 Logic floor 2 03 .... 40 Logic floor 40

Press the COP button for one second to enter the reconfiguration mode of the button. Press/activate shortly the button under reconfiguration to decrease the button/ switch logic ID. Press the DOB button shortly to increase the logic ID.

The COP beeps when entering the reconfiguration mode. COP direction arrow up light lits when the ID is over 99. Arrows up and down lit when the ID is over 199.

* "A" TTC A-side floor "C" TTC C-side floor

4

Press the COP button for one second to save the new configuration and exit from the configuration sub-menu. The COP beeps when exiting.


70 (78)

AS-12.20.027 (A) 2013-05-02


6.3.4

Configuring COP location Step Action 1 In configuration sequence 01, pressing the left/lowermost call button increases the COP Deck value. – The two digit deck value is displayed on the right side of the "Spanner" icon. – The side value (A, B, C, D) is displayed on the right side of the position indicator.

2

D

Note / Illustration Pressing the COP button shortly under reconfiguration, increases the logic floor ID.

t f ra

* 00 Deck value (COP number) not configured 01 COP 1 Deck number 02 COP 2 Deck number

Press the DOB button shortly switch the COP side between A, B, C and D.

* "A" TTC A-side floor "C" TTC C-side floor

3

Press the left/lowermost call button for one second to save the new configuration and exit the configuration menu.


71 (78)

AS-12.20.027 (A) 2013-05-02


6.3.5

Clearing COP configuration

Clear all the configuration in KSSLCBBx and KSSLMUL (the COP must be re-configured from scratch). Step Action 1 In configuration sequence 02,"C" starts to blink on the right side of the position indicator. Press the leftmost/lowermost call button for one second to clear the configuration.

6.4

D

Note / Illustration

t f ra

Testing COP and landing components The following tests are available. Table 7: Test codes Code 00

Name Inspection test


Description Each segment and icon in COP switches on and when pressing pressels or using key switches, COP displays the respective ID and the buzzer or speaker beeps.

72 (78)

AS-12.20.027 (A) 2013-05-02


6.4.1

Using test menu (T - Inspection test)

In test menu, the two digit test codes appear on the right side of the "Spanner" icon starting from 00. Step Action 1 Press the DOB button shortly to confirm the selected test code (00) and to start the inspection test. – See that each segment and icon in the COP switches on/off. – Press each button and use all key switches and check that they are registered. When registered, the button or keyswitch ID displays in COP and the COP beeps.

D

2

6.4.2

Note / Illustration

t f ra

De-activate the maintenance mode by pressing DOB for 10 seconds.

Deactivating maintenance mode

The maintenance mode is deactivated as follows: – –

If the COP is inactive for more than five minutes. By pushing for DOB for 10 seconds.


73 (78)

AS-12.20.027 (A) 2013-05-02


7

ADJUSTING GONG VOLUME Step Action 1 Select the main menu “7” in the user interface of the LCE controller, for miscellaneous parameters. 2 Select the submenu for the volume adjustment. 3 Adjust the parameter value of the submenu with up and down keys of the user interface. 4 Press ACCEPT. 5 Switch the LCE controller power off and on.

D


Note / Illustration For buttons without sound signal the value should be set to 0.

t f ra

74 (78)

7_82 Gong Volume 7_83 Gong Volume at main floor The value range is from 0 (OFF) to 10 (MAXIMUM). This saves the new values. This downloads the new values in the signalization devices.

AS-12.20.027 (A) 2013-05-02


8

COP SOFTWARE UPDATE COP software update is done through SD card located in KSSLMUL board. Step Action 1 Remove the COP from the back plate. 2 Disconnect the power cable. 3 Remove KSSLMUL board from the COP to access SD card socket. 4 Insert the SD card to the SD card socket (1). 5 Connect the power cable. 6 Push reset button S2. The software is now loaded to the PCB. The COP starts to work normally. 7 Remove the SD card.

D

Illustration/Note For more information on removing the COP and KSSLMUL board, see sections 5.4.3 Opening the COP and 5.4.4 Replacing KSS-L multiboard (KSSLMUL).

t f ra

S2

3004587.jpg

1

8

Assemble the COP back.


For more information on closing the COP and returning the elevator to service, see sections 5.4.5 Closing the COP.

75 (78)

AS-12.20.027 (A) 2013-05-02


9

APPROVALS AND VERSION HISTORY Compiled by:

Information Product Author / Petri Ahola

Checked by:

Senior Maintenance Specialist / Jukka Lindberg Product Change Manager / Luca Andreone

Approved by:

Maintenance Method Director / Werner Ettrich

Translation approved by: /

t f ra

Issue Date Description of Change 2012-06-20 First issue. A 2013-05-02 Maintenance mode access method updated. Key switch replacement added. Pictures updated according to the latest design.

D


76 (78)

Ref CR

Approved by Seppo Valliovuo

AS-12.20.027 (A) 2013-05-02


10

FEEDBACK Click one of the star buttons in the PDF version to rate the document and report errors or suggest improvements. This opens your default e-mail client. Users of printed documents can send feedback directly to [email protected]. Excellent

Good

D Average

t f ra

Acceptable

Insufficient


77 (78)

AS-12.20.027 (A) 2013-05-02


KONE Corporation KONE Training and Documentation P.O. Box 679 FI-05801 Hyvinkää, Finland

D


t f ra

78 (78)

AS-12.20.027 (A) 2013-05-02

AS-11.65.051_main_fr_KDL16S

Recommend Documents