Contents
User's Manual Reasons to choose Steelmate -----------------------
2
17. Valet (service mode)---------------------------------- 11
Important notice ------------------------------------------
2
18. Emergency override ---------------------------------- 11
Brief look at transmitters ------------------------------
3
19. Turbo timer mode (F1, F19, F21)------------------ 12
About LCD screen ---------------------------------------
4
20. Transmitter operation range indication----------- 12
Battery indicator ------------------------------------------
4
21. Rearming automatically------------------------------ 12
Transmitter charging ------------------------------------
4
22. Ultrasonic sensor (optional)------------------------- 12
System operating-----------------------------------------
5
23. Tamper alert--------------------------------------------- 12
Status indication -----------------------------------------
6
24. Personal code setting--------------------------------- 12
Functions ---------------------------------------------------
7
24.1. How to enter the personal code------------ 13
1. Arming operation ----------------------------------------
7
2. Passive arming ------------------------------------------
7
3. Disarming operation------------------------------------
7
learning -------------------------------------------------- 13
4. Silent arming/disarming--------------------------------
8
26. System programming -------------------------------- 14
5. Mute arming----------------------------------------------
8
6. Car searching (locating)-------------------------------
8
Installation Manual
7. Remote sensor bypass------------------------------
8
System programming table --------------------------- 16
8. Central door lock/unlock (F3/F4/F15/F25) ---
8
Installation instruction---------------------------------- 21
9. Dome light delay-----------------------------------------
9
Door lock wiring diagrams ---------------------------- 24
10. Remote panic ------------------------------------------
9
Optional relay wiring diagrams----------------------- 25
11. Time/ alarm time/W-mode setting -----------------
9
Hood/trunk pin switch relay wiring diagrams--- 25
12. Low battery indicator -------------------------------
9
Wiring diagram--------------------------------------------- 26
13. Trunk release ------------------------------------------
9
Troubleshooting ------------------------------------------ 27
14. Arming without transmitters------------------------- 10
Warranty ----------------------------------------------------- 28
15. Anti-hijack mode --------------------------------------- 10
Steelmate warranty card-------------------------------- 28
24.2. How to change the personal code--------- 13
Car alarm system
25. Transmitter and transponder (optional) code
User's Manual
16. Transponder card (optional) ------------------------ 10
1
Reasons to choose Steelmate
Important notice
1. Professional manufacturer with German quality standards.
* Please install the system by an authorized engineer.
2. Complete range of products, you can easily choose your favorite product.
* Keep the product and the transmitters away from water.
Brief look at transmitters
Arm Antenna
CH3 CH2
* It is highly recommended to read this manual carefully before using this unit.
3. There are agents/distributors in more than 80 countries to supply local service.
* This product will help you reduce the possibility of losing the car by discouraging theft. It is not a substitute for owner’s vigilance. Please take the valuables with you when leaving the car.
4. More than 100 engineers in the company, you can enjoy the latest technology. 5. More than 300 patents.
* When the transmitter’s operating distance is shorter or its indicator light turns dark, please recharge the 2-way LCD transmitter or change the battery of 1-way transmitter ASAP.
6. Products have international approvals, high quality guaranteed. 7. Leading manufacturer in automotive industry, ISO9001, ISO/TS16949, ISO14001 and OHSAS18001 certified.
F button CH2 button Charging socket
CH3 button
Arm
Disarm Power ON/OFF
The LCD transmitter needs to be turned on before the first use, the factory setting is OFF. Turn LCD transmitter ON: press and hold button for 3 seconds till the transmitter is turned on with melody. Turn LCD transmitter OFF: press and hold button for 5 seconds till the transmitter is turned off with a beep. Transmitter will be shut down when the battery is used up. If the transmitter cannot be turned on, please charge it first.
LCD transmitter is OFF.
2
Disarm
Press button for about 3 seconds till the transmitter is turned on with melody.
3
The backlight will turn on, the icons will light up.
About LCD screen
Battery indicator
System operation
The battery status of the LCD transmitter will be shown on the LCD display.
Button
Button function
Button function optional
Lock doors & arm the system
Press and hold for 2 seconds to arm in mute mode (with siren turned off for one arm cycle)
Unlock doors & disarm the system
Stop alarm
CH2
Press and hold for 2 seconds to activate channel CH2
Press twice to cancel the turbo timer
CH3 then CH2
Press to activate channel CH3 Arm with the 1st-stage of shock sensor bypassed
then CH2 then CH2
Arm with both sensors bypassed
When the battery indicator is empty, the transmitter needs to be charged immediately. The transmitting range will be affected when the battery is low. Battery is full Battery is low Battery is empty.
Transmitter charging Signal bar
Parking lights flashing
Arming with door locked
1st-stage shock sensor bypass
Disarming with door unlocked
Shock sensor bypass
Arming in mute mode
Hoodopened
CH2 then
Silent arming
CH2 then
Silent disarming
CH2 + CH3
Press and hold for 2 seconds for panic mode
Arming mode
Charge the transmitter when the battery is low according to the description below. The transmitter's battery can be charged discontinuously.
Trunk released
+ + CH2
Press and hold for 2 seconds for antihijack mode Press and hold for 2 seconds for car locating
Press and hold for 2 seconds and then press CH2 for mute arm with the first stage of shock sensor bypassed
Press and hold for 2 seconds and then press CH2 twice for mute arm with both sensors bypassed
Press both buttons in armed status for mute arming
Press and hold for 2 seconds twice in 7 seconds to cancel passive arming for one cycle
2-way transmitter
Key
Clock alarm
Ignition ON
System busy
Transmitter vibration
Time/Clock and W-function
Anti-hijack
W-mode ON
Valet mode
Door opened
Insert the charger’s plug into transmitter’s battery charging socket.
4
Insert the charger into the vehicle’s cigarette lighter socket.
F (2-way transmitter)
Press and hold for 5 seconds for Time/Alarm time/W-mode setting
F and (2-way transmitter)
Vibration on/off mode
F and CH3 (2-way transmitter)
Turn on/off W-mode CLOCK SETUP: CH2 = Increase, CH3= Decrease, F = Next, Start = Beep with button press, hold F for 1 second = Exit
5
Status indication
Functions
LED indicator flashing table 1) Fast flashing---passive arming mode
Parking lights flashing table 1) 1 flash --- system armed
2) Slowly flashing ---armed mode
2) 2 flashes --- system disarmed
3) No flash----system disarmed
3) 3 flashes --- system armed with door, hood or trunk opened
4) Turn on solid --- valet mode
4) 4 flashes --- warning about system triggered after disarming
5) 1 flash ... pause --- the first stage shock sensor triggered
1. Arming operation To arm the system, press transmitter button : * The siren will chirp once. * The parking lights will flash once. * The doors will be locked. * The LED will start flashing. The system is armed with engine immobilized. LCD transmitter will beep once and display as below:
If the door or trunk is not closed properly after arming the system, the siren will chirp 3 times with the parking lights flashing, and transmitter will beep 3 times with door icon flashing. 2. Passive Arming F23-- set passive arming ON/OFF, F24-- set door lock/unlock in passive arming When passive arming function is on, after 30 seconds (plus F6 arming delay time), the system will be armed automatically if the car is parked with all the doors closed, the sire will chirp once and the parking lights will flash once. The LED will flash.
5) 5 flashes --- car searching
6) 2 flashes ... pause--- the second stage shock sensor triggered 7) 3 flashes ... pause --- trunk/hood triggered, INST 1 / INST 2 = INST 1
Note: opening the door resets the passive arming timer.
8) 4 flashes ... pause ---door triggered (door (-) or door (+))
When passive arming function is on, press and hold button + twice for 2 sec in 7 seconds after the car is parked with all doors closed, it will cancel passive arming for one cycle. If anti-hijack is activated, it will also be cancelled for one cycle.
While armed, the system will be triggered if: * The door is opened. * The trunk/hood is opened. * The ignition is turned on. * The shock sensor detects an impact. * An optional sensor is triggered. If triggered by the door or trunk/hood input or ignition ON, the siren will sound and the parking lights will flash for 30 seconds.
9) 1 long flash and 3 short flashes---transponder registration confirmed Siren short chirps table 1) 1 chirp --- system armed 2) 2 chirps --- system disarmed 3) 3 chirps --- system armed with door or trunk opened.
Factory setting: passive arming OFF. Note: if the ignition on or trunk is opened in 30 seconds, the passive arming will be cancelled for one cycle. 3. Disarming operation To disarm the system press transmitter button * The siren will chirp twice. * The parking lights will flash twice. * The doors will unlock. The LCD transmitter will beep twice and display as below:
If the shock sensor detects a light impact to the vehicle, the system will chirp and the parking lights will flash 5 times to warn away the potential intruder. A heavy impact will trigger the alarm system or an optional sensor is disturbed, the siren will chirp and the parking lights will flash for 30 seconds.
4) 4 chirps --- warning about system triggered after disarming 5) 5 chirps --- car searching/locating
6
7
F4/1: Doors will not be unlocked when the ignition turns off.
4. Silent arming/disarming Press transmitter button , then press button or , the system will arm or disarm without siren chirp(s).
7. Remote sensor bypass To arm the system and bypass the 1-stage of the shock sensor: press button , then press button in 3 seconds, the siren chirps once and the 1-stage of the shock sensor will be ignored for one cycle.
5. Mute arming Press and hold transmitter button for 2 seconds to arm in mute mode * The siren will not chirp for one cycle * The parking lights will flash once. * The doors will lock. When the system is triggered, the siren will not chirp. The LCD transmitter will show as below:
To arm the system with both sensors bypassed: press button , then press button twice in 4 seconds, the siren chirps twice and both sensors will be ignored for one cycle. The operation of remote sensor bypass in mute arming mode is the same. 8. Central door lock/unlock (F3/F4/F15/F25). F3/1: Doors will not be locked when ignition turns on. F3/2: Doors will be locked automatically when ignition is turned on. F3/3: If you program F15/2 for speedometer input, doors will be locked automatically when the car speed reaches the pre-set speed. F3/4: If you program F25 for "door +" or "door -", and connect wires to footbrake signal wires, doors are locked when the foot brake is pressed.
6. Car searching (locating) Press and hold transmitter button + for 2 seconds, the siren will chirp and parking lights will flash 5 times.
Note: If one of the doors are not closed properly, the doors will not be locked.
8
F4/2: Doors will be unlocked automatically when the ignition turns off.
once, the hour digit will flash, then press button , the flashing icon will change in the sequence below: time/hour time/minute alarm on/off alarm/hour alarm/minute W-mode setting exit.
During driving, press button the doors
Press " " to increase (+) or press " decrease (-).
or
to lock or unlock
" to
9. Dome light delay This function is specifically designed for the vehicle with dome light function. The system will enter the arming mode after the dome light turns off. Arming delay time can be set by F6.
Press and hold button exit setting.
for 1 second to save and
10. Remote panic: In the event of an emergency (panic) situation, the siren can be triggered for 30 seconds to attract attention. Press and hold transmitter button + for 2 seconds to activate the panic function: * The siren will chirp sharply. * The parking lights will flash.
"W-mode" means the time of transmitter sending signals to system can be programmed.The "set" icon will be shown on the LCD transmitter.
W-mode: Press + button together shortly to turn W-mode on/off. According to F21, CH6 can be activated.
12. Low battery indicator The battery status of the LCD transmitter will be shown on the LCD display. When the battery indicator is empty, the transmitter needs to be charged immediately.
Press and hold transmitter button + for 2 seconds or press valet switch (if a personal code is set, you should enter the personal code) to exit.
13. Trunk release Press or button to open the trunk. The shock sensor will bypass when the trunk is opened, and return to normal when the trunk is closed.
11. Time/ alarm time/W-mode setting Press button + to turn on/off the LCD transmitter's vibration mode. Press and hold button for 5 seconds to activate time /alarm time /W-mode setting mode. Press button once, the LCD transmitter beeps
The vehicle must equip with trunk release motor and select or output for trunk release during installation.
9
14. Arming without transmitters Press valet switch once, then press and hold it again for 3 seconds. The siren will chirp once, the LED will flash rapidly. The system will be armed after all doors are closed and send the signals to LCD transmitter. If F24 is on, then the doors will be locked. This function is only for one operation. 15. Anti-hijack mode Anti-hijack mode will be activated automatically or by transmitter (Function F16/F17/F18). Five anti-hijack modes can be programmed: 1) Anti-hijack off. 2) Active: press and hold transmitter button + for 3 seconds to activate the anti-hijack function. 3) Full-time: anti-hijack function will be activated as soon as ignition is turned on. 4) Passive activated with door opened: During driving, opening the door will activate anti-hijack function. 5) Passive activated by speed: the pre-set speed will activate the anti-hijack function.
engine will be blocked periodically. 3) 40 seconds later, the siren will chirp with parking lights flashing rapidly until the car battery is used up, the engine will be blocked completely.
If door is opened and stays open, then the system will delay transponder card searching for 4 minutes. One more minute later, if transponder card is not found, the engine will be blocked.
If you place the transponder card in the working range after 40 seconds when anti-hijack function is activated, you need to deactivate anti-hijack, by valet switch or enter personal code.
To deactivate the anti-hijack function: 1) In 40 seconds, press valet switch once. 2) 40 seconds later, to deactivate the anti-hijack function depends on the setting of F12. I. F12 is "Valet" - turn ignition OFF/ON and press valet switch once in 10 seconds. II. F12 is "Personal code" - enter personal code by valet switch [24.1].
II. To change this protection mode, change F25 for "door +" or "door -" and connect corresponding door trigger wire to the footbrake wire.
17. Valet (service mode) To activate Valet mode: Disarm system, turn ignition on for more than 3 seconds then turn off, press the valet switch once in 5 seconds. The LED will turn on solid. The siren will chirp once every time when the ignition is turned off in valet mode.
16. Transponder card (optional) Please program transponder card into the memory of the system before use.
3 modes of transponder card can be programmed (Function F13) 1) F13/1 Transponder card is deactivated. 2) F13/2 Transponder card is activated with engine block function: I. Once ignition is turned on, the system starts to search transponder card in 1 minute. If the system finds transponder card, the LED indicator flashes (1 long + 3 short) and the system will send signal to the LCD transmitter.
ACC off can stop alarm temporarily. Once ACC is turned on, the system will alarm and block the engine. Once the anti-hijack mode is activated: 1) In 20 seconds, the anti-hijack icon flashes on the transmitter, the siren does not chirp. 2) 20 seconds later, the siren will chirp and the
If system can not find transponder card in 1 minute, the engine will be blocked.
10
The following will happen: * If door is opened, the system will search transponder card when the footbrake is pressed. * If the footbrake is pressed and transponder card is not found in 1 minute, engine will be blocked. * If door is opened, the system will search transponder card in 4 minutes when the footbrake is not pressed. * If transponder card is registered successfully with door closed, pressing footbrake will not activate transponder card searching, opening door will activate transponder card searching.
In valet mode, doors lock/unlock and panic functions can be operated by transmitter. To deactivate valet mode: Turn ignition on for more than 3 seconds then turn off, press valet switch in 5 seconds. 18. Emergency override If the transmitter is lost or fails to operate, the system can be disarmed by using the emergency override feature. To override the system depends on F12.
3) F13/3 Transponder card is activated with antihijack function: once ignition is turned on, system will search transponder card. If system does not find transponder card in 1 minute it will activate anti-hijack.
F12 -"Valet": Opening the door with key ( the siren will chirp). Turn ignition on, press valet switch once in 10 seconds. F12 -"Personal code": Enter the personal code [24.1]. If wrong personal code was input three times, you need to wait for more than 3 minutes to enter personal code again.
If you place the transponder card in the working range in 40 seconds when anti-hijack function is activated, anti-hijack will be stopped.
11
19. Turbo timer mode (F1, F19, F21) The time can be programmed (F1). Turbo timer works after the engine runs for more than 60 seconds. If the turbo timer mode is on, when you take out the key, the engine will keep running, the parking lights will flash once every 2 seconds. The remaining time will be shown on LCD transmitter.
transmitter shows that the transmitter is within the operation range of the system. The signal icon will disappear in 2 minutes when the LCD transmitter is out of the operation range and cannot receive the signal from the system. At the same time, 2 beeps will be heard when any LCD transmitter button is pressed.
Turbo timer mode keeps the engine running after arriving at you destination for a programmable period of 1, 3, 10, 15 or 30 minutes (F1). This allows the system to cool down the turbo after you have left the vehicle.
When a transmitter sends signal to the system, the system only send feedback signal to the transmitter. 21. Rearming automatically When the system is disarmed by pressing button and the doors are not opened in 20 seconds (plus F6 arming delay time), the system will rearm with the doors locked automatically (door lock or unlock is determined by F5). The siren will beep once with parking lights flash.
To activate turbo timer mode, "turbo timer output" (F19/2 or F21/2) needs to be set. * Turn off the key, the engine will keep running. * The LCD transmitter will beep 3 times and the display will show: * The parking lights will flash once every 2 seconds to indicate the turbo timer mode is on. * The engine will turn off after the programmed time runs out.
22. Ultrasonic sensor (optional) When the ultrasonic sensor is triggered by detecting an object movement inside the vehicle, the siren will alarm for 30 seconds with parking lights flashing. The engine will be immobilized. 23. Tamper alert If the alarm was triggered while you are away from the vehicle, the siren will chirp 4 times with the parking lights flash on disarming for tamper indication. The LED will flash the zone that was triggered.
To cancel turbo timer mode: a) Take the key out b) Press button twice c) Siren will chirp twice and the parking lights will flash once.
24. Personal code setting Personal code can be programmed (F12). The factory setting personal code is 11.
20. Transmitter operation range indication In armed mode, the signal icon on the operated LCD
12
24.1. How to enter the personal code: Disarm system, turn ignition off and wait for 5 seconds, then turn ignition ON/OFF/ON. Press and release the valet switch the number of times according to the first digit of personal code in 10 seconds. (eg. The first digit of factory setting personal code is 1, press and release the valet switch once).
10 seconds, the siren will chirp accordingly. Turn ignition on, the siren will send out one short and one long chirp to confirm the new personal code is set successfully. If the changing is not successful, please disarm the system and repeat the procedure mentioned above. 25. Transmitter and transponder (optional) code learning To learn new transmitters, the learning procedures will be different depending on the settings of F12:
Turn ignition OFF/ON. Press and release the valet switch the number of times according to the second digit of personal code in 10 seconds.
F12 - valet Switch off the power of the transponder card (if available)
Turn ignition OFF/ON. When the input personal code is correct, the system will send out a "short" chirp and a "long" chirp.
Disarm system, turn ignition on. Press valet switch 3 times, the siren will chirp once. Press and hold button on the first transmitter till one chirp is heard, and then LED will start to flash slowly. Press and hold button on the second transmitter till one chirp is heard, and then LED will start to flash slowly. Only 2 transmitters can be programmed for the system.
24.2. How to change the personal code: After the correct personal code is entered, turn ignition off in 5 seconds. Press valet switch 5 times, the siren will send out one short and one long chirp to confirm entering the setting mode. Press transmitter button once in 5 seconds (the siren will chirp once). Press valet switch the number of times according to the first digit of the personal code (from 1 to 9) in 10 seconds, the siren will chirp accordingly. Press transmitter button once in 10 seconds (the siren will chirp once). Press valet switch the number of times according to second digit of personal code (from 1 to 9) in
Switch on the power of transponder card, the transponder card will be programmed successfully with one chirp. Turn ignition off to exit or 10 seconds later to exit automatically.
13
F12 - personal code Switch off the power of the transponder card (if available) Follow the steps of "How to enter the personal code" [24.1], the siren will chirp once to confirm if personal code is correct. Press valet switch 3 times, the siren will chirp once. Only 2 transmitters can be programmed for the system. Switch on the power of transponder card. The siren will chirp once to confirm transponder card is programmed (If available). Turn ignition off to exit or 10 seconds later to exit automatically.
System will enter the F1 programming mode (LED will flash once after one pause). In programming mode, the number of times LED flashes is corresponding to the function number. To change function setting, press transmitter button (1~5 times). According to the different function settings, the siren will send out 1/2/3/4/5 chirps. Press valet switch to go to next function. If you do not press any button in 10 seconds, system will exit programming mode. F12 - Personal code: function programming Enter the personal code [24.1]. Siren chirp will confirm if personal code is correct. Press valet switch 3 times in 3 seconds. Siren will chirp once. Turn ignition off in 3 seconds. Siren will chirp once. Turn ignition on in 3 seconds. Siren will chirp once. System will enter the F1 programming mode (LED will flash once after a pause).
26. System programming F1-F10 can be programmed and it is independent of F12. F12 - valet F1-F25 can be programmed. F12 - personal code F1-F10 can be programmed without personal code. F11-F25 can be programmed only after entering personal code. System will exit programming mode if there is no button pressed in 10 seconds.
Car alarm system Installation Manual
In the programming mode, the number of the LED flashes is corresponding to the function number in system programming table. To change function setting, press transmitter button . According to the different function settings, the siren will send out 1/2/3/4/5 chirps.
F12-valet: function programming Disarm system, turn ignition on, press valet switch 3 times in 3 seconds. Siren will chirp once. Turn ignition off in 3 seconds. Siren will chirp once. Turn ignition on in 3 seconds. Siren will chirp once.
Press valet switch to program next function. If you do not press any button in 10 seconds, system will exit programming mode.
14
15
System programming table Continued
Function Description
System programming table Function Description
1 chirp Press button once
2 chirps Press button twice
3 chirps Press button 3 times
F1
Turbo timer
1 min
3 min
F2
Limitation of false alarm
Off
On
F3
Ignition locking
Off
On
F4
Ignition unlocking
Off
On
F5
Auto rearm
Off
On with unlocking
On with locking
F6
Arming delay
5 sec
35 sec
60 sec
F7
Door locking/ unlocking pulse
0.5 sec
1 sec
3.5 sec
F8
F9
CH2 output
10 min
4 chirps
5 chirps Press button 5 times
Press button 4 times
15 min
30 min
Footbrake
Speed locking locking (Ref.F25)
1 sec unlock pulse ×2
button CH2 again to stop
Press button CH3, Press button CH3, Press button CH3 Press button CH3, Press button CH3, signal "-" 3.5 sec 0.4 sec, signal "-" signal "-" 0.4 sec, signal "-" 1 sec, pause 0.3 sec, pause 0.5 sec, 12 sec
CH3 output signal "-" 1 sec
CH4 output
When armed, signal "-" 1 sec
When armed, When armed, When disarmed, When armed, signal "-" 10 sec signal "-" 15 sec signal "-" 30 sec signal "-" 20 sec
Restore factory setting
Off
2 chirps
4 chirps
5 chirps
On
F12
Valet/Personal mode setting for programming
Valet mode
F13
Transponder card
Off
On
F14
Ignition warning in disarmed mode
Off
On
F15
INST2 (-) extra input trigger
F16
Anti-hijack by transmitter
Off
On
F17
Anti-hijack by ignition on
Off
On
On by driver side door opening (-)
F18
Anti-hijack by ignition on
Off
On by driver side door opening (+)
On by speed
F19
INST2 (-) extra input trigger
Personal code On while antihijack activated
Speedometer input (-)
Turbo timer output (-) To be continued
To be continued
16
3 chirps
Programming the function F12- F25 depends on the mode of F12, "valet mode" or "personal code mode" are available.
Press button CH2 Press button CH2 Press button CH2, Signal "-" when signal "-" 30 sec signal "-", press ignition on signal "-" 1 sec
signal "-" 0.4 sec signal "-" 1 sec
F10
F11
1 chirp
17
Continued
Function Description
1 chirp
2 chirps
F20
CH5 output
F21
When disarmed, CH6 output: two blue/black signal "-" 20 sec wires
F22
Window/ sunroof closer
F23
Passive arming
Off
On
F24
Door lock if passive arming on
Off
On
F25
STOP (-/+) function of door trigger
3 chirps
4 chirps
5 chirps
Pager (-)
Off
Off
Turbo timer (-)
10 sec
W-trigger (start W-trigger (start W-trigger (start and stop by for 1 sec by for 1/0.5/1 sec real time) real time) by real time) 15 sec
22 sec
30 sec
F3/4: the doors will be locked when footbrake is pressed (by F25) automatically. The system will not lock the doors if any door is opened when the ignition is turned on.
to turn on device, such as releasing trunk. F8/2: the blue wire will output signal (-) for 30 seconds to roll up windows. F8/3: the blue wire will output signal (-), press CH2 button again to stop output signal (-). F8/4: the blue wire will always output signal (-) after ignition on.
F4 Ignition unlocking F4/1: the doors will not be unlocked when ignition is off; F4/2: the doors will be unlocked automatically when ignition is off;
F9 CH3 output Press transmitter button CH3 to activate this feature: F9/1: the green/red wire will output signal (-) 1 second to turn on device, such as releasing trunk. F9/2: the green/red wire will output signal (-) for 3.5 seconds. F9/3: the green/red wire will output signal (-) for 12 seconds F9/4: the green/red wire will output signal (-) for 0.4 seconds, pause 0.3 seconds and then output signal (-) for 0.4 seconds again. F9/5: the green/red wire will output signal (-) for 1 second, pause 0.5 seconds and then output signal (-) for 1 second again.
F5 Auto rearm Automatically rearms the system in case of accidental disarming. Select among auto rearm off, auto rearm without door locking and auto rearm with door locking.
Door (+)
Door (-) The shaded options are factory setting
Note: F1 Turbo timer Turbo timer function will be activated after ignition is on for more than 1 minute (F19/2 or F21/2 need to be programmed). It will keep a turbo vehicle engine running for 1, 3, 10, and 15 or 30 minutes according to F1 after you remove the key.
input, keeping the other zones protected until the next time the system is armed. F3 Ignition locking F3/1: the doors will not be locked automatically when ignition is on; F3/2: the doors will be locked automatically when ignition is on; F3/3: the doors will be locked when the car's speed reach the pre-set speed (with F15/2)
F2 Limitation of false alarm If the same input triggers the system 6 times during a single arming cycle, the system will bypass that
18
F6 Arming delay This optional arming delay mode allows system to delay arming for 5, 35 or 60 seconds. This mode is designed for vehicle with dome light delay. F7 Door lock/ unlock pulse Select between a 0.5 second lock/0.5 second unlock, 1 second lock/1 second unlock for standard vehicles, 3.5 seconds lock/3.5 seconds unlock for vacuum lock system, 1 second lock/1 second unlock 2 times for some Japanese vehicles.
F10 CH4 output: F10/1~4: When the system is armed, the Green/White wire can output signal (-) for different time to activate other devices: 1 second, 10 seconds, 15 seconds or 30 seconds. F10/5: when the system is disarmed, the Green/White wire will output signal (-) for 20 seconds.
F8 CH2 output Press transmitter button CH2 to activate this feature: F8/1: the blue wire will output signal (-) for 1 second
19
Installation instruction
F11 Restore factory setting: This option allows the system to restore the factory setting rapidly.
F16 Anti-hijack by transmitter To activate the anti-hijack by pressing transmitter button and together when ignition is on.
F12 Valet/Personal mode setting for programming There are two modes of F12: Valet mode and Personal code mode. When F12 is in Valet mode, you can program the functions/features of F12~25 through Valet switch. When F12 is in Personal code mode, you can program the functions/features of F12~25 by input personal code.
F17 Anti-hijack by ignition on To activate the anti-hijack by ignition on or by a door opening (-) while the ignition is on. F18 Anti-hijack by ignition on To activate the anti-hijack by a door opening (+) while the ignition is on or by the speedometer trigger. F19 Arm (-) F19/1: The output (-) of Black/White wire is reverse to the armed output (-) (Orange wire). That means, when the Orange wire outputs signal (-), the Black/White wire will not output signal (-), when the Orange wire does not output signal (-), the Black/White wire will output signal (-). F19/2: Black/White wire will output signal (-) for turbo timer.
F13 Transponder card The transponder card is an additional upgrade accessory. F13/1 Turn off the transponder card detection. F13/2 Turn on the transponder card detection. If the transponder card is not found, the engine will be immobilized. F13/3 Turn on the transponder card detection and anti-hijack will be activated automatically when the transponder card is not detected.
F20 CH5 output F20/1: The output (-) of Gray wire is reverse to the armed output (-) (Orange wire). F20/2: The Gray wire will output a signal (-) to trigger a pager when the alarm system is triggered.
F14 Ignition warning in disarmed mode In disarmed mode, when ignition is on, the ignition icon ( ) will show on the LCD transmitter.
F21 CH6 output: two blue/black wires Select between turbo timer and W-mode. F21/1: output signal (-) for 20 seconds after disarmed. This option is recommended to trigger the headlight output.
F15 INST2 (-) extra input trigger Select between an INST2 extra input (-) or a speedometer input (-).
20
F21/2: output signal (-) for turbo timer according to the time of the F1 setting. F21/3/4/5: The channel will activate according to the W-mode setting. Select among 1 start and stop by real time (according to the Wmode setting to start and stop); 2 start for 1 second by real time (according to the w-mode setting to start for 1 second signal); 3 start for 1/0.5/1 sec by real time (according to the w-mode setting start for 1 second and pause for 0.5 second then a 1 second signal)
Before you begin the installation * Read the INSTRUCTIONS!
F22 Window/sunroof closer This option suits for vehicle with automatic window/sunroof close function. Select for 10 seconds, 15 seconds, 22 seconds or 30 seconds to close the window/sunroof.
Mounting ECU Mount the ECU under the dash where it will be difficult for a potential thief to locate the module, and away from moving parts such as brake pedals, etc.
F23 Passive arming The system will arm automatically 30 seconds after the car is parked and all doors are closed.
Antenna module For optimum range and performance, the antenna module should be located high up on the front windshield glass. For example: behind the rearview mirror.
* Always use a multi-meter when verifying vehicle wiring. * Before mounting the product, verify with the customer's desired location for the valet switch and LED. * Always look before drilling. Make sure you will not cause damage to vehicle hoses, electrical looms or physical damage to vehicle.
F24 Door lock if passive arming on All doors will lock while passive arming.
Note: Window tints or Films may decrease the range of the system. The mounting surface for the antenna should be clean and dry.
F25 STOP (-/+) function of door trigger F25/1: no change to the door trigger F25/2: door trigger (+) wire (violet) will be defined not for door trigger, e.g. it can be defined as a footbrake trigger (+). F25/3: door trigger (-) wire (brown) will be defined not for door trigger, e.g. it can be defined as a footbrake trigger (-).
Mounting siren Mount the siren in a suitable place under the hood, away from hot and moving engine parts. Make sure the siren cannot be accessed from underneath the
21
vehicle or through the grill. Face the siren down so that water cannot accumulate inside the siren bell. Protect wires running through the firewall using either tape or split loom tubing.
* BLUE/ RED WIRE - INST2 input (-).
* YELLOW WIRE -- IGN1, +12V ignition input.
a. Connect to hood pin switch or trunk switch. b. Connect to speed sensor of "VAZ" vehicle (F15. F3).
Connect to a main ignition wire at the ignition switch harness. This wire shows +12V when the ignition is on and while cranking. The voltage must not drop when the car is starting. IGN1(+)
* RED WIRE -- +12V Battery input. Connect the red
Mounting shock sensor Secure the shock sensor to the steering column, thick wire harness or a dash brace, using a wire tie.
fused wire on the main harness to a constant +12V source. * BROWN WIRE -- Negative door trigger (-). Connect
Make sure that the adjustment screw is accessible for later testing and adjustment.
to the door switch circuit wire that shows ground when the door is open.
20-Pin main harness * BLACK WIRE -- Ground input (-). Connect to a solid chassis ground that is clean and free of paint or dirt.
* WHITE WIRE --Parking lights output (+). Connect to the vehicle's parking lights wire. * VIOLET WIRE -- Positive door trigger (+). Connect
* ORANGE WIRE -- Armed output (-) 500mA. Connect to a relay for optional circuit defeat (See installation diagrams). The ORANGE wire provides a ground 40 seconds when the unit is armed to activate a fuel pump disable relay or other device (i.e. window control module, etc.).
4-Pin White Connector A: Plug-in connector port for 2-stage shock sensor. Contact of additional relay to control turbo timer mode for channel ARM (-), CH6 or "TRIGGER" of channel CH2.
* GREEN / RED WIRE -- CH3 output (-) 1A. Please refer to the System programming table F9.
* BLUE / BROWN WIRE - INST1 input (-). Connect
* GRAY WIRE - CH5 output (-) 500mA. (F20).
to hood pin switch or trunk switch. The BLUE / BROWN wire provides a ground when the hood or trunk opened.
* BLACK / WHITE WIRE - ARM (-) 500mA. * BLUE / BLACK WIRE - CH6 output (-) 1A. ( F21). * YELLOW / BLACK WIRE -- IGN2, +12V ignition input. Connect to the wire going to the starter. The voltage of this wire output can keep engine running according to the Turbo timer.
22
Output ignition wire from car ignition lock
* GREEN / WHITE WIRE - CH4 output (-) 500mA. * BLUE WIRE - CH2 output (-) 500mA. (F8).
Connect to the siren's red wire. Connect the siren's black wire to ground.
Wire that supplies+12 V to car ignition lock
2-Pin Connector: Plug-in connector port for valet switch. Mount switch in an area that is easily accessible from the driver's seat. The switch should be well hidden. It should be placed so passengers or stored items (such as in a glove box or central console cannot accidentally hit it.
IGN2(+)
to the door switch circuit wire that shows +12V when the door is open. This type of door circuit is usually found on Ford vehicles. (F10).
* WHITE / BLACK WIRE -- Siren wire output 5A(+).
Ignition contact of car ignition lock
Plug in connectors 2-Pin Connector: Plug-in connector port for LED. Mount LED in an area where it may be easily seen from either side of the vehicle.
4-Pin White Connector B: Plug-in connector port for optional ultrasonic sensor.
6-Pin door lock connector * BLUE / WHITE WIRE -- Lock relay N/O (87). * YELLOW WIRE -- Lock relay Common (30). * GREEN WIRE -- Lock relay N/C (87a). * ORANGE WIRE -- Unlock relay N/O (87). * WHITE WIRE -- Unlock relay common (30). * BLUE WIRE -- Unlock relay N/C (87a).
23
Door lock wiring diagrams
Optional relay wiring diagrams
ADDING ACTUATORS
NEGATIVE PULSE LOCK SYSTEM
L UL
(-) DOOR LOCK (-) DOOR UNLOCK
GREEN
NC
YELLOW
COM
BLUE/WHITE GREEN
NC
YELLOW
COM
BLUE/WHITE BLUE
NO NC
WHITE
COM
ORANGE
NO
NO
BLUE
NC
WHITE
COM
ORANGE
NO
+12V
Hood / trunk pin switch relay wiring diagrams
POSITIVE PULSE LOCK SYSTEM
VACUUM LOCK SYSTEM
REVERSE POLARITY LOCK SYSTEM VACUUM PUMP
UL
GREEN
NC
YELLOW
COM
BLUE/WHITE BLUE
NO NC
WHITE
COM
ORANGE
NO
GREEN
NC
YELLOW
COM
BLUE/WHITE
NO
BLUE
NC
WHITE
COM
ORANGE
NO
GREEN
NC
YELLOW
COM
BLUE/WHITE
CUT
BLUE
L
X
(+) DOOR UNLOCK CUT
NO
COM
ORANGE
NO
Blue
V
NC
WHITE
X
UL
To hood / trunk release
L
(+) DOOR LOCK
X
L
Hood / trunk pin switch
CUT
UL +12V +12V +12V
24
25
Wiring diagram
Troubleshooting
Fault 1. The continuous chirping of the siren cannot be stopped by transmitter after the installation of ECU.
Blue / Brown
Causes The plug is improperly inserted. The wire is improperly connected. The transmitter does not match the ECU. The siren is damaged. The fuse of the ECU is broken
INST1(-)
White / Black 20
Blue / Red
Door trigger wire is not connected properly. Door switch has problem. The siren is damaged.
2. Parking lights do not flash after disarming the system and opening the door, or the siren does not chirp when the door is opened without disarming.
5A
INST2(-)
3. When the car parks on roadside and armed, there are false alarms by passing heavy vehicles.
The sensitivity of the sensor is too high.
4. The central door lock does not work normally or does not work at all. Sensor (optional)
15A
Brown
Parking lights 7.5A
CH3 output (-)
Green / Red Green / Red Yellow
IGN2 (+)
Yellow / Black
CH6 output (-)
The siren is damaged. The wire connection between the siren and ECU has problem.
6. The siren chirps sharply in 10 seconds after arming and the same situation happened after disarming and re-arming it again.
The sensor is damaged. The doors or trunk is not closed. The door's pin switch has problem or wiring has problem.
7. Transmitter is ineffective or the control distance decreased significantly.
The installation location of the antenna is wrong. The wiring of the antenna to ECU has problem. Tall building, radio tower or high frequency electromagnetic wave may affect the remote range. Low power of the battery. The frequency of the transmitter has been changed. The transmitter is broken or damaged.
Door trigger (+)
Black / White
IGN1 (+)
5. The siren does not chirp when the alarm system is triggered. Door trigger (-) 7.5A
Arm (-)
The motor of central lock is damaged. The wiring of central lock system is wrong. Fuse is broken.
Green / White
CH4 output (-)
CH2 output (-)
Blue 5A
Gray
Blue / Black Blue / Black
26
CH5 output (-)
27
Warranty
Steelmate warranty card
I. The unit is warranted for a limited period from the date of purchase. In the unlikely event of a defect arising in this product when used in accordance with the manufacturer's instructions, the parts would be repaired or replaced free of charge.
User: Tel: Vehicle Reg No.:
It is required to show warranty card when making any warranty claims.
Product Model No.:
The model and serial number on unit must be the same as the information on the warranty card.
Serial No.: II. This warranty is non-transferable and is automatically void if: Date of Installation:
The original purchaser has not completed the warranty card.
Name of the Retailer:
The unit's serial number is defaced, missing or altered.
Signed by Retailer:
The unit has been modified or used in a manner contrary to its intended purpose. The unit has been damaged by accident, unreasonable use, neglect, improper installation or service. III. The warranty does not cover damage to the unit caused by installation or removal of the unit.
28