List of DIN Standards
Logo of DIN German Institute for Standardization
The list gives an overview of the naming system of the DIN standards with standard number, part of s additives. It also tells about standards, their titles, as well as their validity and possible replacement a addition to Contents 1 Identification of standard number and date of issue 2 List by number 2.1 DIN 1-999 2.2 DIN 1000-1999 2.3 DIN 2000-2999 2.4 DIN 3000-3999 2.5 DIN 4000-4999 2.6 DIN 5000-5999 2.7 DIN 6000-6999 2.8 DIN 7000-7999 2.9 DIN 8000-9999 2/10 DIN 10000-14999 2/11 DIN 15000-17999 2/12 DIN 18000-18298
2/13 DIN 18299-18459 German construction contract procedures - Part C: General technical specificat contracts (ATV) 2/14 DIN 18500-18999 2/15 DIN 19000-19999 2/16 DIN 20000-29999 2/17 DIN 30000-39999 2/18 DIN 40000-49999 2/19 DIN 50000-59999 2/20 DIN 60000-69999 2/21 DIN 70000-99999 2/22 DIN EN 1-999 2/23 DIN EN 1000-1999
2/24 2/25 2/26 2/27 2/28 2/29 2/30 2/31 2:32 2:33 2:34
DIN EN 2000-9999 DIN EN 10000-19999 DIN EN 20000-59999 DIN EN 60000-99999 DIN EN 100000 from DIN EN ISO 1-9999 DIN EN ISO 10000-99999 DIN IEC DIN ISO and ISO / IEC DIN VDE LN standards (aviation)
2:35 VG standards (for "defense equipment", the German Federal Office of Defense Technology and P published) 3 Weblink Designation of standard number and date of issue [ Edit ] At the standard number can be seen which originates a standard:
DIN: (. Eg DIN 33430 ) DIN standard, published exclusively or mainly of national importance or as a pr supranational document.
DIN CEN / TS or DIN CLC / TS: (. Eg DIN CLC / TS 50459-1): Unchanged German adopting a European T Specification.
DIN CWA: (. Eg DIN CWA 14248) Unchanged German takeover of a CEN - or CENELEC Workshop Agree Rule).
EN: (. Eg DIN EN 14719) German takeover of a European Standard (EN). European standards must, if t are unchanged by the members of CEN and CENELEC.
DIN EN ISO: (. Eg DIN EN ISO 9921): Under the auspices of ISO or CEN resulting standard, which will be organizations.
DIN EN ISO / IEC: (. Eg DIN EN ISO / IEC 7810) German standard based on a European standard, which International Standard ISO / IEC.
DIN EN ISP: (. Eg DIN EN 10608-6 ISP): German standard based on a European standard, which is base standard profile. ISO: (. Eg ISO 10002): Unchanged German takeover of an ISO standard. DIN IEC: (. Eg DIN IEC 60912): Unchanged German takeover of IEC norm.
DIN VDE Subjects Electrical, Electronic and Information Technology jointly by DIN and VDE by the DKE of DIN VDE standards .
Attention Are DIN standards behind the label "DIN" with another letter - except "VDE" - re have their own numbering system, for example: DIN 3 standard dimensions, but with DIN extinguishers.
A standard part is with a hyphen and the number of the standard part denoted (z. B. Part 1 of EN 3 as it was "part 1" advertised or "T. 1 "(abbreviated. Eg DIN 14093 Part 1); Today, this supplement is adve standard s The issue date of detection is the calendar month in exact figures for a colon quoted, eg DIN 1301-1. shown on the title page with name ausgeschriebenem month of October of 2002.
Until about 1969 maintained a standard to slight changes in their issue date of, the change was noted small Malkreuz; z. B. means "in March 1953xx" that issued in March 1953 standard has been revised t "cross expenditur
By 1940 standards had some subjects between the word "DIN" and the number one letter code, for. E mining, HNA for shipbuilding, LON for the locomotive and Kr for the automotive industry. After the intr standard numbers
List by Numbers [ Edit ] See also: Category: DIN in alphabetical order of the numbers Notices The list is not exhaustive. In order to guarantee the timeliness of the standards listed here she continuously takes the Beuth Ver The standard titles are out in force at the time of issue of the relevant standard spelling. DIN 1-999 [ Edit ] see list of standards DIN 1 to DIN 499 (the preparation also lists historical standard editions) see list of standards DIN 500 to DIN 999 (the preparation also lists historical standard editions) DIN 1000-1999 [ Edit ] DIN 1000 steel structures - version, replaced by DIN 18800-7 DIN 1013 Hot rolled round steel Part 1 of general application, February 2004 replaced by DIN EN 10060 Part 2 for a specific purpose, in February 2004 replaced by DIN EN 10060 DIN 1014 Hot-rolled square steel Part 1 Steel bars for general purpose February, replaced in 2004 by DIN EN 10059 Part 2 bars, for a specific purpose, in February 2004 replaced by DIN EN 10059 DIN 1015 steel bars, hot rolled steel hexagon February, replaced in 2004 by DIN EN 10061 DIN 1016 Flat products made of steel, hot-rolled strip, hot rolled sheet, November 1996 replaced by D DIN 1017 steel bar, hot rolled flat steel Part 1 of general application, February 2004 replaced by DIN EN 10058 Part 2 for a specific purpose, in February 2004 replaced by DIN EN 10058 DIN 1018 steel bars, hot rolled steel half round and half round flat steel, March 2005 withdrawn withou
DIN 1019 steel bars; Hot rolled bulb flats, weights, dimensions, tolerances, static values, December 19 EN 10067 DIN 1022 steel bars, hot rolled steel angle isosceles sharp edges (LS-steel) DIN 1024 steel bars, hot rolled round-edged T-steel, January 1996 replaced by DIN EN 10055 DIN 1025 Hot rolled I-beam Part 1 I-series Part 2 IPB series Part 3 IPBl series Part 4 IPBv series Part 5 IPE-series DIN 1026 Hot-rolled steel U-profile Part 1 with inclined flange
Part 2 with parallel flanges DIN 1027 steel bars, hot rolled round-edged Z-steel DIN 1028 Hot-rolled, isosceles circular edge angle steel, Nov. replaced in 1998 by DIN EN 10056-1 DIN 1029 Hot-rolled, round-edged unequal angle steel, Nov. replaced in 1998 by DIN EN 10056-1 DIN 1041 locksmith hammers DIN 1042 Sledge Hammers, Demolition Hammers Cross DIN 1045 structures from concrete , reinforced concrete and prestressed concrete Part 1 Design and construction, January 2011 replaced by DIN EN 1992-1-1 and EN 1992-3 Part 2 Concrete - Specification, performance, production and conformity - Application rules for DIN EN Part 3 Construction - National Annex to DIN EN 13670 Part 4 Supplementary rules for the production and conformity of precast Part 100 brick ceilings DIN 1048 Testing concrete Part 1 fresh concrete Part 2 hardened concrete in structures and components Part 4 Determination of compressive strength of hardened concrete in structures and components Part 5 hardened concrete, separately prepared specimens DIN 1052 Preparation and execution of timber structures (part 1-3 withdrawn, now DIN EN 1995-1-1) Part 1 Design and construction Part 2 Mechanical connections Part 3 wooden houses in panel construction - Design and construction Part 10 Supplementary Provisions DIN 1053 masonry (withdrawn, now DIN EN 1996-1-1) Part 1 Design and construction Part 2 Masonry strength classes on the basis of aptitude tests Part 3 reinforced masonry - Design and construction Part 4 Precast Part 11 Simplified method for detection of unreinforced masonry Part 12 The construction and design of unreinforced masonry Part 13 Detailed design method for unreinforced masonry Part 14 Design and construction of masonry made of natural stone Part 100 calculation based on the semi-probabilistic safety concept DIN 1054 Building - Verification of the safety of earthworks and foundations DIN 1055 Actions on structures Part 1 Densities and weights of building materials, structural elements and stored materials Part 2 Soil Characteristics Part 3 equity and imposed load in building Part 4 Wind loads Part 5 Snow and ice Part 6 Actions on Silos and tanks Part 7 of the effects of temperature
Part 8 Actions during execution Part 9 Unusual effects Part 10 actions due cranes and machinery Part 100 Basis of structural design, safety concept and design rules DIN 1069 waterslides - Safety requirements and test methods DIN 1072 Road and foot bridges; Loads Supplement 1 road and foot bridges; Load assumptions; Explanations DIN 1076 Engineering structures in connection with roads, inspection and testing DIN 1089 Refractories for coke ovens Part 1 silica bricks - Requirements and testing Part 2 firebricks - Requirements and testing Part 3 mortar for silica and fireclay bricks; Requirements and testing DIN 1100 hard materials for cementitious hard aggregate screeds - Requirements and test methods
DIN 1101 wood-wool slabs and multi-layer lightweight panels as insulating products for building (inval replaced by DIN EN 13168 and DIN V 4108-10) DIN 1101 Domestic fireplaces for solid fuels - Emission Testing (SPEC) DIN 1159 loops with one side cut tip DIN 1164 Special cement Part 10 Composition, specifications and conformity evaluation for cement with low effective alkali con Part 11 Composition, specifications and conformity evaluation for cement with short setting
Part 12 Composition, specifications and conformity evaluation for cement with an increased proportion constituents DIN 1193 hammers made of steel - Technical delivery conditions DIN 1195 eye dimensions for hammers and forging tools DIN 1229 unit weights for tops and manhole tops for traffic areas DIN 1236 Concrete elements and buckets for operations; Class A and Class B Part 1 construction, installation and compilations Part 2 concrete parts Part 3 buckets DIN 1249 sheet glass in building DIN 1259 glass DIN 1289 Feuergeschränk for tile; Stoke-hole Füllfeuerung DIN 1301 units Part 1 unit name, unit characters Part 1, Supplement 1, unit Similar Names and Emblems Part 2 Commonly employed parts and Multiples Part 3 conversions for no longer applicable units DIN 1302 General mathematical symbols and concepts DIN 1304 Symbols DIN 1305 mass, weight value, force, weight, force, weight, load DIN 1306 density DIN 1310 Composition of mixed phases (gas mixtures, solutions, mixed crystals); Terms, Symbols
DIN 1311 vibrations and vibration systems DIN 1312 Geometrical orientation DIN 1313 sizes DIN 1314 print Basic concepts, units DIN 1315 angle DIN 1318 volume level DIN 1319 Measurement Technology DIN 1320, Acoustics DIN 1324 Electric Field DIN 1325 Field DIN 1332 symbols acoustics DIN 1333 figures DIN 1335 Geometrical Optics - descriptions and definitions DIN 1338 Formula spelling and math typesetting DIN 1339 units magnetic variables DIN 1340 Gaseous fuels and other gases; Types, components, using DIN 1342 viscosity; Newtonian fluids DIN 1343 reference state, standard state, standard volume DIN 1349 passage of optical radiation by media Part 1 An optically clear materials, quantities, symbols and units Part 2 optically opaque materials, concepts DIN 1353 abbreviations of terms Part 1 Elemental abbreviations, April 1997 replaced by DIN ISO 5261 Part 2 for semi-finished April 1997 replaced by DIN ISO 5261 DIN 1355 time
Part 1 calendar week numbering , date, time; November 1994 back without replacement; Successor t DIN 1356 illustration of lines and hatching in drawings Part 1 Types, content and general rules for representation Part 6 of buildings and construction Part 10 drawings reinforcement drawings, in June 1996 replaced by DIN ISO 3766 and DIN ISO 4066 DIN 1357 units of electrical quantities DIN 1412 Twist Drill High Speed ??Steel - Anschliffformen DIN 1421 branches and numbering in texts DIN 1422 publications in science, technology, business and administration Part 1 of Manuscripts and typescripts Part 2 Design of fair copies for Reprographic Processes Part 3 Typographic Design Part 4 design of research reports DIN 1434 bolts DIN 1440 slices , implementing medium, for bolts, Oct. replaced in 1992 by DIN EN 28738
DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN
1441 1443 1444 1448 1449 1450 1451 1455 1460 1463 1464 1469 1474 1478 1479 1480 1481 1501
slices, Model coarse, for bolts pin without head, Oct. replaced in 1992 by DIN EN 22340 Clevis pins with head, Oct. replaced in 1992 by DIN EN 22341 Conical shaft ends with male thread Conical shaft ends with internal thread fonts; legibility DIN font manuscript (replaces DIN 1451 Supplement 5) May 2001 withdrawn without replacement Conversion of cyrillic alphabets Slavic languages Thesaurus loose-leaf publications (-werke); Additional deliveries shape and arrangement Paßkerbstifte with neck Grooved pins plug, Oct. replaced in 1992 by DIN EN 28741 Turnbuckles made of steel tube or round steel Hexagon turnbuckles Turnbuckles, forged (open form) spring pins (Adapter sleeves), heavy duty, August 1993 replaced by DIN EN 28752 periodicals; Order feature withdrawn without replacement on the outer envelope, August 19
DIN 1502 Rules for the shortening of words in titles and for the shortening of the publication titles of M withdrawn without replacement
Supplement 1 reduction in the title of journals and similar publications; Abbreviations of words from la Latin and Cyrillic characters, October 1989 withdrawn without replacement DIN 1503 design of scientific journals and trade magazines, January 1987 withdrawn without replacem DIN 1504 literature maps, Feb. 1995 withdrawn without replacement DIN 1505 Title Information Document Part 1 withdrawn titles intake of literature, pre-standard, March 2007 without replacement Part 2 Citation Part 3 directories cited documents (bibliographies)
Part 4 title information of documents: remote recording tracks of audio-visual materials, pre-standard, replacement DIN 1541 Cold-rolled sheet and High-alloy steel, since 1992, replaced by DIN EN 10131 DIN 1543 Hot-rolled from 3 to 150 mm thickness, since 1992, replaced by DIN EN 10029 DIN 1544 Cold-rolled steel strip, November 1996 replaced by DIN EN 10140
DIN 1570 Hot-rolled ribbed steel spring; Dimensions, weights, tolerances, static values; January 2004 10092-2 DIN 1587 Hexagon domed cap nuts, high DIN 1588 rail vehicles; Kick handle units; Design notes DIN 1596 Light Saddles steel einlaschig suit with possibility for rail vehicles DIN 1683 Rough steel castings - General tolerances, machining allowances; Not for new designs DIN 1686 Rough castings of gray iron - General tolerances, machining allowances; Not for new design DIN 1687 Rough castings of heavy metal alloys Part 1 sand castings - General tolerances, machining allowances
Part 3 die casting, general tolerances, machining allowances Part 4 die casting; General tolerances, machining allowances DIN 1688 Rough castings of light alloys Part 1 sand castings - General tolerances, machining allowances; Not for new designs Part 3 die casting, general tolerances, machining allowances Part 4 die casting; General tolerances, machining allowances DIN 1700 non-ferrous metals , Nomenclature of Designation, May 2000 withdrawn without replacemen DIN 1702 nickel anodes
DIN 1705 copper-tin and copper-tin-zinc alloy castings (cast tin bronze and gunmetal) - Casting Decem 1998 by DIN EN 1982 DIN 1707 solders , composition, application, technical specifications, March 1994 replaced by DIN EN DIN 1708 copper - cathodes and Gußformate May, replaced in 1998 by DIN EN 1976 and DIN EN 1978 DIN 1709 copper-zinc casting alloys (cast brass and cast brass Special) - Casting December, replaced 1982 DIN DIN DIN DIN DIN DIN
1714 1716 1718 1729 1732 1754
copper-aluminum casting alloys (cast-aluminum bronze) - Casting December, replaced in 19 copper-lead-tin casting alloys (cast tin-lead bronze) - Casting December, replaced in 1998 b copper alloys - Terms and definitions magnesium alloys Welding consumables for aluminum and aluminum alloys Copper tubes and pipes, nahtlosgezogen, July 2002 replaced by DIN EN 12449 and DIN EN 1
DIN 1769 rectangular bars of aluminum and aluminum alloys, drawn with sharp edges, September 19 EN 754-5 DIN 1770 rectangular bars of aluminum and aluminum alloys, pressed January, replaced in 1987 by D DIN 1786 installation copper tubes, nahtlosgezogen, May 1996 replaced by DIN EN 1057 DIN 1787 copper - semi-finished products DIN 1804 locknuts; ISO metric fine thread DIN 1810 hook key DIN 1814 Wrench, adjustable DIN 1816 Cross hole nuts; ISO metric fine thread DIN 1850 Slide Bushings DIN 1871 Gaseous fuels and other gases DIN 1897 Extra short twist drills with straight shank DIN 1910 Welding Part 1: Definitions, classification of welding processes, Nov. 2002 replaced by DIN ISO 857-1 Part 2: welding, welding of metals, procedures, Nov. 2002 replaced by DIN ISO 857-1 Part 3: welding, welding of plastics, process Part 4: Arc welding, process, Nov. 2002 replaced by DIN ISO 857-1 Part 5: metal welding, resistance welding, process, Nov. 2002 replaced by DIN ISO 857-1 Part 10: Mechanized arc welding processes, terms, Nov. 2002 replaced by DIN ISO 857-1 Part 11: Materials-related terms for metal welding Part 12: Manufacturing-related terms for metal welding, Nov. 2002 replaced by DIN ISO 857-1
DIN 1912 Graphical representation; Welding, soldering Part 1: Concepts and terms for welded joints, fugues, stitching, June 1999 replaced by DIN EN 12345 Part 2: Working positions, seam inclination angle seam rotation angle, in June 1997 replaced by DIN E
Part 2: Supplement 1: working position, inclination angle seam, seam rotation angle, determining the the tube (example), June 1997 replaced by DIN EN ISO 6947 Part 4: Concepts and Terms for Lötstöße and Seams Part 5: symbols, dimensioning, ISO 2553, 1984 edition modified December, replaced in 1987 by DIN E
Part 5 Supplement 1: symbols, dimensioning, application examples of symbols for seam types accordi December 1987 replaced by DIN EN 22553 DIN 1940 internal combustion engines; Reciprocating engines, terms, symbols, units DIN 1942 acceptance tests on steam generators (for determination of efficiencies ) DIN 1943 Thermal acceptance tests in steam turbines (VDI steam Rules) DIN 1944 acceptance tests on centrifugal pumps (centrifugal pumps VDI-rules), replaced by DIN EN IS DIN 1945 displacement compressors DIN 1946 Ventilation and air conditioning Part 1 terminology and graphical symbols January, replaced in 2004 by DIN EN 12792 Part 2 Health Technical Requirements May 2005 replaced by DIN EN 13779 Part 3 air-conditioning of passenger cars and trucks Part 4 HVAC systems in hospitals (VDI ventilation rules) Part 6 residential ventilation; Requirements, performance, acceptance (VDI ventilation rules) Part 7 HVAC systems in laboratories (VDI ventilation rules)
DIN 1952 Measurement with orifice plates, nozzles and Venturi tubes in full flow-through tubes of circu (VDI Durchflußmeßregeln) (Replaced with DIN EN ISO 5167-1) DIN 1960 General requirements for the award of construction contracts (see also VOB, Part A ) DIN 1961 Terms and conditions for the execution of works (see also VOB, Part B ) DIN 1986 Drainage systems for buildings and land Part 3 rules for operation and maintenance Part 4 Fields of application of sewage pipes and fittings of different materials Part 30 maintenance Part 100 Additional regulations for DIN EN 752 and DIN EN 12056 DIN 1988 Standard for drinking water installations (TRWI) Part 1 General (retired) Part 2 Planning and execution; Components, apparatus, materials (withdrawn) Part 2, Supplement 1 set of standards and other rules about materials, components and equipment Part 3 Determination of the pipe diameter (withdrawn) Part 3, Supplement 1 Calculation examples (withdrawn) Part 4 Protection of drinking water (in conjunction with DIN EN 1717 Protection of Drinking Water) (wit Part 5 pressure boosting and reduction (withdrawn) Part 6 fire fighting and fire protection systems (withdrawn) Part 7 Prevention of corrosion and scale formation (withdrawn) Part 8 operation of the plants (withdrawn) Part 100 Protection of drinking water, drinking water quality; DVGW code of practice
Part 200 Installation Type A (closed system) - Planning, components, equipment, materials; DVGW cod Part 300 Determination of the pipe diameter; DVGW code of practice Part 500 pressure boosting systems with variable speed pumps; DVGW code of practice
Part 600 drinking water installations in connection with fire fighting and fire protection systems; DVGW DIN 1989 Rainwater harvesting systems Part 1 design, implementation, operation and maintenance Part 3 rainwater storage DIN 1996 Testing of Bituminous Materials for Road Building and Related / Testing of asphalt Part 2 sampling Part 9 Swelling Test Part 11 Determination of Marshall stability and Marshall flow Part 13 with a flat punch indentation Part 14 Determination of particle size distribution of asphalt extracted from minerals Part 15 Determination of the softening point, according to Wilhelmi Part 16 Determination of the tendency to separate Part 17 Determination of dimensional stability under heat (deformation value by Nüssel) Part 18 ball drop test according to Herrmann Part 19 Determination of ductility and adhesion in the joint model Rabe DIN 1999 Separator systems for light liquids Part 7 Proseparate detergent; Requirements, testing (pre-standard) Part 100 requirements for the application of separation in accordance with DIN EN 858-1 and EN 858-2
Part 101 Additional requirements for separation in accordance with DIN EN 858-1, EN 858-2 and DIN 1 liquids with parts of biodiesel or fatty acid methyl esters (FAME) DIN 2000-2999 [ Edit ] DIN 2000 Central drinking water supply Guidelines for drinking water planning, construction and oper DIN 2001 drinking water supply from small units and non stationary plants
Part 1 small systems - Guidelines for drinking water, planning, construction, operation and maintenan DVGW code of practice
Part 2 Non stationary units - Guidelines for drinking water, planning, construction, operation and main equipment; DVGW code of practice DIN 2023 metal packaging - fitted lids, round Part 1 dimensions, materials, labeling Part 2 core teachings Part 3 capping DIN 2025 doses for sausages DIN 2032 metal packaging; Screw Caps Blackplate DIN 2046 bucket for sauerkraut and pickles, cylindrical; withdrawn without replacement DIN 2092 Disc springs , Calculation DIN 2093 Disc springs, dimensions, quality requirements DIN 2096 Helical compression springs made of round wire and rod Part 1 Quality requirements for hot formed compression springs
Part 2 Quality Requirements for Mass Production DIN 2098 Cylindrical helical springs made from round wire (withdrawn) Part 1 Dimensions for Cold formed compression springs with 0.5 mm wire diameter Part 2 sizes for cold formed springs below 0.5 mm wire diameter DIN 2101 typewriter platen roller rocker arm for typewriters DIN 2107 Typewriter font sizes, spacing, line spacing base (type body type lever for typewriters) DIN 2108 Typewriters (naming the machine types and concepts and classification) DIN 2112 Alphanumeric keyboards ; Key arrangements for hand-operated typewriter. DIN 2127 Alphanumeric keyboards; Key arrangement for electromechanically driven typewriters DIN 2137 Alphanumeric Keyboards DIN 2172 Reamers Part 1 Technical delivery conditions for reamers with shank Part 2 Technical delivery conditions for slip-reamers
DIN 2194 Cylindrical helical springs made of round wire and rod - Cold-formed torsion springs (torsion standard DIN 2197 Taps - Technical delivery conditions for ground Taps speed steel DIN 2201 Machine tools; Taper shanks with driver for taper size 3 to 6 and metric taper size 80 to 200 DIN 2207 for tool shanks Frässpindelköpfe according to DIN 2201 - Connecting dimensions DIN 2211 drive elements; Narrow V-belt pulleys Part 1 dimensions, material Part 2 Examination of the grooves DIN 2215 Endless belts - Classical V-belts - Dimensions DIN 2216 Finite V-belts; Mass DIN 2217 drive elements; V-belt pulleys Part 1 dimensions, material Part 2 Examination of the grooves DIN 2269 Verification of geometrical parameters - Pins DIN 2275 feeler gauges
DIN 2279 Geometrical product specifications (GPS) - Lessons for ISO metric screw threads - gauging o thread; Overview, labeling, marking, application DIN 2280 Geometrical product specifications (GPS) - thread plug gauges for ISO metric screw threads application from 1 mm to 40 mm nominal thread diameter DIN 2281 Geometrical product specifications (GPS) - Thread Gutlehrdorne
Part 1 Gutarbeitslehren, testing and setting gauges for ISO metric screw threads of general application mm nominal thread diameter
Part 2 Gutarbeitslehren, testing and setting play for ISO metric screw threads of general application fr mm nominal thread diameter DIN 2282 Verification of geometrical parameters - Thread Gutlehrenkörper
Part 1 Gutarbeitslehren, testing and setting gauges for ISO metric screw threads of general application mm nominal thread diameter
Part 2 Gutarbeitslehren, testing and adjusting body for ISO metric screw threads of general application mm nominal thread diameter
Part 3 Gutarbeitslehren and check plugs for ISO metric screw threads over 40 mm up to 250 mm nom for use in precision engineering DIN 2283 Geometrical product specifications (GPS) - Committee thread plug gauges
Part 1 Committee working gauges, testing and setting plug for metric ISO thread for general applicatio mm nominal thread diameter
Part 2 Committee working gauges, testing and setting play for ISO metric screw threads of general ap mm to 200 mm nominal thread diameter
Part 3 Committee working gauges and check plugs for ISO metric screw threads over 40 mm up to 25 thread diameter for use in precision engineering DIN 2284 Verification of geometrical parameters - thread Committee gauge body
Part 1 Committee working gauges, testing and setting gauges for ISO metric screw threads of general mm to 40 mm nominal thread diameter
Part 2 Committee working gauges, testing and setting play for ISO metric screw threads of general ap mm to 200 mm nominal thread diameter
Part 3 Committee working gauges and check plugs for ISO metric screw threads over 40 mm up to 25 thread diameter for use in precision engineering DIN 2330 concepts and terms; General principles DIN 2332 Naming of internationally equivalent concepts DIN 2340 Short forms for terms and names DIN 2342 terms of terminology teaching ; Part 1 Basic Concepts DIN 2345 translation tasks ; December 2006 withdrawn without replacement (see also DIN EN 15038) DIN 2353 soldering compression fittings with cutting ring - Complete fittings and survey DIN 2391 Seamless precision steel tubes, since 2003, replaced by DIN EN 10305-1 DIN 2395 welded precision steel tubes with rectangular and square cross-section, replaced by DIN EN DIN 2401 Pressure and temperature data Part 1 terms, pressure ratings, September 1997 replaced by DIN EN 764-1 DIN 2403 Colour codes for pipelines DIN 2405 pipes in refrigeration and cooling equipment - Marking
With DIN 2413 Seamless steel pipes for oil and water hydraulic systems - Calculation rules for pipes a dynamic loads DIN 2425 Plans for public utilities, water management and for transmission lines Part 1 pipe network plan of public gas and water supply Part 2 pipe network plan for district heating Part 3 plans for pipelines, DVGW code of practice Part 4 channel network plan public sewers Part 5 maps and plans of the Water Part 6 maps and plans for water engineering, the flood and coastal protection DIN 2429 Graphical symbols for technical drawings, Piping Part 1 General Part 2 Functional display DIN 2430 Piping for pigging systems Part 1 pipes and elbows
Part 2 tube connections Part 3 checks before commissioning DIN 2440 medium weight threaded pipe , Replaced by DIN EN 10255 DIN 2441 Heavy threaded barrel, Replaced by DIN EN 10255 DIN 2442 threaded pipes with Quality Specifications, nominal pressure from 1 to 100 DIN 2444 galvanized steel tubes, since 1998, Replaced by DIN EN 10240 DIN 2445 Seamless steel tubes for dynamic loads Part 1 hot-finished tubes for hydraulic systems 100 bar to 500 bar Part 2 precision steel tubes for hydraulic systems 100 bar to 500 bar DIN 2448 Seamless steel tubes, since 2003 Replaced by DIN EN 10220 DIN 2458 Welded steel tubes, boiler tubes, Replaced by DIN EN 10220 DIN 2462 Seamless tubes of stainless steels Part 1 Dimensions, masses per unit length, in June 1996 Replaced by DIN EN ISO 1127 DIN 2463 Welded tubes made of austenitic stainless steels Part 1 Dimensions, masses per unit length, in June 1996 Replaced by DIN EN ISO 1127 DIN 2470 gas lines made of steel pipes with maximum operating pressure up to 16 bar Part 1 requirements for components DIN 2501 flanges Part 1 connection dimensions, Nov. 2007 Replaced by EN 1092-1 / 2 DIN 2507 screws and nuts for pipelines, January 2000 Replaced by EN 1515-1 DIN 2509 bolts DIN 2510 Bolted connections with Reduced shank Part 1: Overview, Scope and installation examples Part 2 Metric thread with great game, nominal dimensions and limits of size Part 3 bolts Part 4 studs Part 5 hex nuts Part 6 cap nuts Part 7 expansion sleeves Part 8 threaded holes for studs DIN 2512 flanges - tongue and groove PN 10 - PN 160, June 2002 Replaced by EN 1092-1 DIN 2513 Flanges - nose and tongue PN 10 - PN 100, June 2002 Replaced by EN 1092-1 DIN 2514 flanges - lead with recess and return PN 10 - PN 100, June 2002 Replaced by EN 1092-1 DIN 2519 steel flanges - Technical delivery June 2002 Replaced by EN 1092-1 DIN 2526 flanges - forms the sealing surfaces, Nov. 2007 Replaced by EN 1092-1 DIN 2527 Blind flanges, PN 06 - PN 100, June 2002 Replaced by EN 1092-1 DIN 2558 Oval threaded flanges, smooth - PN6 DIN 2559 Weld preparation
Part 1 Guidelines for joint preparation, fusion welding of butt joints in steel pipes, May, 2004. Replaced 9692-1 Part 2 Customize the inside diameter for Circumferential welds on seamless pipes
Part 3 Customize the inside diameter for Circumferential welds on welded pipes Part 4 Customize the inside diameter for Circumferential welds on seamless tubes of stainless steels DIN 2565 with threaded flanges approach, PN 06, June 2002 Replaced by EN 1092-1 DIN 2566 with threaded flanges approach, PN 10, June 2002 Replaced by EN 1092-1 DIN 2567 with threaded flanges approach, PN 40, June 2002 Replaced by EN 1092-1 DIN 2573 Flanges, clogged for soldering or welding PN 6, June 2002 Replaced by EN 1092-1 DIN 2576 Flanges, clogged for soldering or welding PN 10, June 2002 Replaced by EN 1092-1
Connectors Data slide for boiler tubes
DIN 2605 fittings for welding, pipe bends, Part 1 Decreased utilization, June 2008 Replaced by EN 10253-2 / 4 Part 2 Full utilization, June 2008 Replaced by EN 10253-2 / 4 DIN 2607 pipe bends - Made of copper for welding DIN 2609 steel fittings for welding Part 1 Decreased utilization, June 2008 Replaced by EN 10253-2 / 4 Part 2 Full utilization, June 2008 Replaced by EN 10253-2 / 4 DIN 2615 pipe fittings, tees Part 1 Decreased utilization, June 2008 Replaced by EN 10253-2 / 4 Part 2 Full utilization, June 2008 Replaced by EN 10253-2 / 4 DIN 2616 pipe fittings, reducers, concentric and eccentric, June 2008 Replaced by EN 10253-2 / 4 DIN 2617 pipe fittings, caps, dimensions, June 2008 Replaced by EN 10253-2 / 4 DIN 2618 steel fittings for welding; Saddles, nominal pressure 16 September 1997 WITHDRAWN witho DIN 2627 Welding neck PN 400, June 2002 Replaced by EN 1092-1 DIN 2628 Welding neck PN 250, June 2002 Replaced by EN 1092-1 DIN 2629 Welding neck PN 320, June 2002 Replaced by EN 1092-1 DIN 2630 Welding neck nominal pressure 1 and 2.5, Replaced by EN 1092-1 DIN 2631 Welding neck nominal pressure 6, Replaced by EN 1092-1 DIN 2632 Welding neck nominal pressure 10 Replaced by EN 1092-1 DIN 2633 Welding neck nominal pressure 16 Replaced by EN 1092-1 DIN 2634 Welding neck nominal pressure 25 Replaced by EN 1092-1 DIN 2635 Welding neck nominal pressure 40 Replaced by EN 1092-1 DIN 2636 Welding neck nominal pressure 64 Replaced by EN 1092-1 DIN 2637 Nominal pressure welding neck 100, Replaced by EN 1092-1 DIN 2638 Welding neck PN 160, Nov. 2007 Replaced by EN 1092-1 DIN 2641 Loose flanges - Vorschweißbördel - Smooth league PN 6, June 2002 Replaced by EN 1092-1 DIN 2642 Loose flanges - Vorschweißbördel - Smooth league PN 10, June 2002 Replaced by EN 1092-1 DIN 2655 Loose flanges - Smooth league PN 25, June 2002 Replaced by EN 1092-1
DIN 2656 Loose flanges - Smooth league PN 40, June 2002 Replaced by EN 1092-1 DIN 2673 Loose flanges with welding PN 10, June 2002 Replaced by EN 1092-1 DIN 2695 Diaphragm Seals welding and weld ring gaskets for flanged connections DIN 2696 flange with sealing lens DIN 2796 flange with threaded collars, stress. Issue June 1948 WITHDRAWN Standard DIN 2805 Flange with Vorschweißbunden, stress. Withdrawn Edition May 1948 standard DIN 2827 Hose assemblies of stainless steel for chemical substances DIN 2848 Flanged steel pipes and flanged fittings made of steel and cast iron lining - PN 10, PN 25 an DIN 2856 solder fitting , Replaced by DIN EN 1254 DIN 2860 handling systems DIN 2867 for solder fittings Part 1 angleFrom red brass, May 1984 WITHDRAWN without replacement DIN 2873 Flanged steel pipes and flanged fittings made of steel with enamel - PN 10 and PN 25
DIN 2874 Flanged steel pipes and flanged fittings made of steel and cast iron liner made of PTFE or PF delivery conditions
DIN 2875 flanged pipes and flanged fittings made of steel with a lining of hard or soft rubber - Technic conditions DIN 2880 Application of cement mortar lining for cast iron pipes, steel pipes and fittings DIN 2950 DIN EN 10242 Malleable Replaced by DIN 2980 steel threaded pipe, August 2000 Replaced by DIN EN 10241 DIN 2981 steel threaded pipe - long thread, August 2000 Replaced by DIN EN 10241 DIN 2982 steel threaded pipe - pipe nipple - barrel nipple, August 2000 Replaced by DIN EN 10241 DIN 2983 steel threaded pipe - bow, August 2000 Replaced by DIN EN 10241 DIN 2986 steel threaded pipe - sockets, August 2000 Replaced by DIN EN 10241 DIN 2987 steel threaded pipe Part 1 Cross - T - angle, August 2000 Replaced by DIN EN 10241 Part 2 T - angle - Reduced, August 2000 Replaced by DIN EN 10241 DIN 2988 steel threaded pipe - paragraph sleeves, August 2000 Replaced by DIN EN 10241 DIN 2990 steel threaded pipe - double nipple with hexagon - Reducer, August 2000 Replaced by DIN E DIN 2991 steel threaded pipe - Plugs - Caps, August 2000 Replaced by DIN EN 10241 DIN 2993 steel threaded pipe - pipe fittings, August 2000 Replaced by DIN EN 10241 DIN 2999 Whitworth pipe threads for tubes and fittings (6 parts), March, 2005 Replaced by DIN EN 102 DIN 3000-3999 [ Edit ] DIN 3110 ended spanner - Test torques nach series C DIN 3113 Combination spanner with same size each - Test torques series A and C DIN 3114 Einmaulschlüssel - Test torques nach series C DIN 3122 with male square drive parts for hand-operated sockets DIN 3123 connectors with male square for hand-operated sockets DIN 3124 sockets with square drive for Hexagon, manually operated DIN 3140 dimensions and tolerances for optical items (2.2000 Replaced by DIN ISO 10110-1 ... 12) Part 1: Presentation, dimension-registration, materials Part 2: bubbles
Part 3: Schlieren Part 4: Tensions Part 5: form errors Part 6: Centering Part 7: Surface defects Part 8: Surface finish Part 9: Surface Coatings Part 10: defects of surface coatings Part 11: representation in tabular form (draft) May Replaced in 1998 by ISO 10110-10 DIN 3158 Refrigerant Valves - Safety requirements - testing - Identification DIN 3159 Flange for Refrigerant fittings to ND 25 DIN 3160 passage shut-off valves for Refrigerant circuits, nominal pressure 25 DIN 3161 Eck shut-off valves for Refrigerant circuits, nominal pressure 25 DIN 3162 Protective caps for valves for Refrigerant circuits, nominal pressure 25 DIN 3163 through control valves for Refrigerant circuits, nominal pressure 25 DIN 3164 position indicator for valves in Refrigerant circuits DIN 3202 Lengths of Valves Part 1 flanged, December 1995 Replaced by DIN EN 558-1 Part 4 valves with female thread connection Part 5 valves with Rohrverschraubungsanschluß DIN 3211 fittings Part 1 terms and definitions, April 1995 Replaced by DIN EN 736-1 DIN 3220 hand wheels, flat - Hub hole with a tapered square DIN 3223 activation key for fittings DIN 3230 Technical specifications for valves Part 1 inquiry, order and delivery, in June 2003 Replaced by DIN EN 12266-1 Part 2 General requirements, June 2003 Replaced by DIN EN 12266-1 and DIN EN 12570 Part 3 compilation of Possible tests, June 2003 Replaced by EN 12266-1 / 2 Part 4 valves for drinking water, requirements and testing Part 5 valves for gas lines and gas equipment, requirements and tests Part 6 fittings for flammable liquids, requirements and testing DIN 3236 Durchflußschauglasarmaturen with seal in the force shunt Part 1 Without lining Part 2 By Email lining DIN 3237 Durchflußschauglasarmaturen with seal in the main load Part 1 Without lining Part 2 with plastic liner Part 3 With rubber lining DIN 3247 Suction strainers with flange without backflow preventer DIN 3280 Valves for domestic water installations; Unions nominal pressure 10 (with cone seal); Survey DIN 3319 hand-wheels, dished - Hub hole with a tapered square
DIN 3320 safety valves; Safety Shut Part 1 terms, sizing, marking; April 2009 retired, DIN EN ISO 4126 and DIN EN 794 recommended Part 3 lengths of safety valves with flanged to PN 40 and up to DN 250 DIN 3321 underground hydrants PN 16 DIN 3322 fire hydrants PN 16 DIN 3334 Heating mixer with flange, ND 6 max. 110 ° C - Three-way mixing valve, four-way mixer, dim
DIN 3335 Heating mixer with female thread, ND 6 max. 110 ° C; Three-way mixing valve, four-way mi . To DIN 3336 Heating mixer with welding ends, ND 6 max 110 ° C; Three-way mixing valve, four-way DIN 3338 Connections of rotary actuators to valves - clutch size for the dog clutches (Form C) DIN 3339 Valves - Materials for housing parts
DIN 3341 disk valves for displacement compressors - Suction, pressure valves - Main dimensions, mat DIN 3352 slideshow Part 1: General Information Part 5 steel gate valves with internal or external spindle thread isomorphic series DIN 3354 flaps Part 1: General Information, march Replaced in 1998 by DIN EN 593 Part 2 valves , Tightly closing, resilient seated, cast iron, with flanges, march Replaced in 1998 by DIN
Part 3 valves, tightly closing, resilient seated, steel and cast steel, flanged or butt weld ends March Re DIN EN 593
Part 4 valves, tight fitting, steel and cast steel, metal seated, with flanges or welding ends March Repl EN 593
Part 5 WITHDRAWN butterfly valves, tightly closing, centric, for clamping or flanging with soft sealing March 1999 without replacement DIN 3356 valves Part 1: General Information Part 2 stop valves made of cast iron, Jan. 2003 Replaced by DIN EN 13789 Part 3 shut-off valves non-alloy steel, Jan. 2003 Replaced by DIN EN 13709 Part 4 stop valves temperature steels, Jan. 2003 Replaced by DIN EN 13709 Part 5 shut off valves stainless steels, Jan. 2003 Replaced by DIN EN 13709 Part 6 WITHDRAWN shut off valves cryogenic steels, draft August 1983 without replacement DIN 3357 Ball Valves Part 1: General Information for ball valves made of metallic materials Part 2 steel ball valves with full bore, July 2006 Replaced by DIN EN 1983 Part 3 steel ball valves with Reduced bore, July 2006 Replaced by DIN EN 1983 Part 4 ball valves made of non-ferrous metals with full bore, February 2007 Replaced by DIN CEN / TS Part 5 ball valves made of nonferrous metals, Reduced bore, February 2007 Replaced by DIN CEN / TS Part 6 ball valves, WITHDRAWN from cast iron with full bore, without replacement in May 1997 Part 7 ball valves, WITHDRAWN from cast iron with Reduced bore, without in May 1997 replacement DIN 3358 Connections of linear actuators to valves - Interface dimensions for flanged
DIN 3360 gas appliances; Domestic cooking appliances burning gas Part 4 Heizherde DIN 3360 Domestic cooking appliances burning gas Part 13 covers on the devices DIN 3363 gas appliances for commercial kitchen equipment Part 3 ceramic-Kochfelder For herd; Requirements and testing DIN 3383 Hose assemblies and connection fittings Part 1 Safety gas hose assemblies, safety connection fittings Part 2 Hose assemblies for rigid connection Part 4 Safety gas connection valves and fittings for laboratory hoses and hose assemblies DIN 3384 Hose assemblies of stainless steel - Safety requirements, testing, marking DIN 3389 Insulating for service lines in the gas and water supply; Ready made ??insulating, requireme DIN 3394 Automatic control valves Part 1 actuators to back up, blowing and rules for surrounding pressures above 4 bar to 16 bar Part 3 actuators to blow, class 0 for surrounding pressures up to 4 bar DIN 3401 oiler and oil jars; Main dimensions DIN 3404 Flat grease nipple DIN 3411 Staufferbüchsen; light duty
DIN 3440 Temperature control and limiting for thermo-technical systems (heating), March, 2003 Repla DIN 3444 caps for pipe fittings with welded and threaded ends
DIN 3476 accessories and fittings for raw and drinking water - Corrosion protection by EP internal coat coatings (P) or liquid varnishes (F) - Requirements and tests
DIN 3489 Air Couplers - Dog clutch claw 42 mm distance, without locking nut - external thread, intern trousers and connect coupling, rotating claw coupling, sealing ring
DIN 3502 valves for drinking water installations in land and buildings - Valves straight through - slopin valve) shell; DVGW code of practice
DIN 3512 valves for drinking water installations in land and buildings - Valves straight through - shell u valve) DIN 3535 Gaskets for gas supply
Part 5 sealing materials, rubber, cork and synthetic fibers for gas fittings and gas appliances; Safety r testing
Part 6 Gasket materials based on fibers, graphite or polytetrafluoroethylene (PTFE) for gas valves, gas pipes DIN 3567 Pipe Clamps for northwest 20 to 500 DIN 3570 U-bolts DIN 3581 gas pipelines; Street Cap size 1 DIN 3582 gas pipelines; Street Cap size 2 DIN 3760 Radial shaft seals Withdrawn DIN 3770 O-rings, September 1993 without replacement DIN 3771 O-Rings DIN 3780 seals; Gland diameter and associated package widths, construction sheet
DIN 3840 fitting housing - Strength calculation for internal pressure, Oct. 2004 Replaced by DIN EN 12 DIN 3852 stud - ports for pipe fittings, valves Part 1 locking screws with metric fine pitch thread, design dimensions Part 2 design dimensions for metric fine thread DIN 3853 Solderless and brazed tube fittings - threaded stud to the union nuts - Construction Journal DIN 3859 Pipe fittings Part 1 Technical delivery conditions Chapter 2 Assembly instructions for solderless fittings with cutting rings nach DIN 2353 and DIN EN IS DIN 3861 Solderless pipe connections - Cutting Rings - Styles DIN 3863 tube fittings - Ball Bushings - design and bore shapes U and Y DIN 3870 Solderless and brazed tube fittings - Union nuts series LL DIN 3871 Solderless and brazed pipe fittings, fittings times DIN 3900 soldering compression fittings with cutting ring - screw-series LL with tapered thread DIN 3901 soldering compression fittings with cutting ring - screwed with parallel thread for screw-type DIN 3955 soldering compression fittings with cutting ring - Taper shaft for PTO Form A DIN 3960 concepts and parameters for spur gears (spur gears) and gear pairs (cylinder gear) with inv DIN 3962 Tolerances for Cylindrical Gear Teeth Part 1 tolerances for Deviations of individual determinants Part 2 Tolerances for flank line Deviations Part 3 tolerances for split-range Deviations DIN 3964 center distance education and Achslagetoleranzen of housings for spur gear DIN 3971 concepts and parameters for bevel gears and bevel gear pairs DIN 3972 reference profiles of gear cutting tools for involute splines nach DIN 867 DIN 3975 concepts and parameters of cylindrical worm gear pairs with intersecting axes perpendicula Part 1 worm and worm wheel Part 2 variations DIN 3979 Tooth Damage on Gear Trains, description, characteristics, causes DIN 3990 Calculation of load capacity of spur gears Part 1 Introduction and general influence factors Part 2 Calculation of pitting Part 3 Calculation of tooth Part 5 endurance limits and material qualities Part 6 Fatigue account DIN 3998 Denominations on Gears and Gear Pairs Part 1: General terms Part 2 track gears and gear pairs (cylinder and cylinder gear wheels) Part 3 bevel gears and bevel gear pairs, hypoid gears and Hypoidradpaare Part 4 worm and wheel DIN 4000-4999 [ Edit ] DIN 4000 Tangible article characteristics (various standard parts) DIN 4002 Properties and Their scopes for product data exchange
Chapter 1 Basics Part 2 Definitions and conceptual information model Part 3 Content and data-technical definition of feature attributes Part 4 Terminology rules for attributes for elements Part 5 units for quantitative characteristics Part 6 of content and information technology definition of the structure Part 7 rules for the formation of the scope of application hierarchy Part 16 Content and data-technical definition of attributes for elements of units and sizes Part 100 features under www.DINsml.net Part 101 application classes under www.DINsml.net DIN 4017 Subsoil - Calculation of basic bearing capacity of shallow foundations DIN 4020 Geotechnical investigations for civil engineering purposes DIN 4021 Subsoil - exploration by trial pits and boreholes; sampling Replaced January 2007 by DIN EN DIN 4022 subsoil and groundwater, short description, naming and description of soil and rock
Part 1 layers directory and drilling without continuous recovery of nucleated samples , January 2007 R ISO 14688-1, ISO 14689-1, DIN EN ISO 22475-1 Part 2 layers directory for drilling in rock (hard rock) , January 2007 Replaced by DIN EN ISO 22475-1
Part 3 layers directory for drilling with continuous production of cored samples in soil (loose rock) , Jan by DIN EN ISO 22475-1
DIN 4023 Geotechnical investigation and testing - Graphical representation of the results of drilling an outcrops DIN 4024 machine foundations Part 1 flexible structures did support machines with rotating masses Part 2 stiffness (rigid) foundations for machinery with periodic excitation DIN 4030 assessment concrete aggressive water, soil and gases Chapter 1 Basics and limit Part 2 sampling and analysis of water and soil samples DIN 4033 drainage and sewerage, and guidelines for execution DIN 4034 Manholes concrete, steel fiber and reinforced precast concrete Part 2 slots for wells and percolation Part 10 manhole bases masonry for underground drainage and sewerage - Requirements and tests DIN 4040 Grease separators Part 100 requirements for the application of separation in accor dance with DIN EN 1825-1 and EN 182 DIN 4044 Hydro Mechanics in Hydraulic Engineering; Terms DIN 4045 Wastewater Engineering, Basic Concepts DIN 4046 Water supply; term; DVGW code of practice DIN 4047 agricultural water; Terms Part 1 development of irrigation waters, drainage Part 2 flood protection, coastal protection, pumping stations Part 3 soil science, soil classification and soil analysis Part 4 bogs and bog soils Part 5 improvement and maintenance of water
Irrigation Part 6 Part 7 erosion control Part 9 drainage, drainage Part 10 properties of soil as plant habitat ; March 2002 Replaced by DIN 4047-3 DIN 4048 Hydraulic Engineering , Terms Part 1 dams Part 2 hydropower plants DIN 4049 Hydrology (Hydrology) Part 1 Basic Concepts Part 2 terms of water quality Part 3 terms for the quantitative hydrology DIN 4050 Wastewater Engineering (terms and definitions) , Replaced by DIN 2425-4 DIN 4052 Concrete elements and buckets for road gullies Part 1: General requirements and installation Part 2 compilations and designations Part 3 concrete parts Part 4 buckets DIN 4054 Waterway terms DIN 4055 water pipes; Surface box for underground hydrants; DVGW code of practice DIN 4056 water pipes; Surface boxes for shut-off valves, DVGW code of practice DIN 4060 pipe joints of sewers and drains with elastomer seals - containment requirements and tests Elastomeric seals DIN 4063 signs for civil defense DIN 4065 gas pipelines; Signs DIN 4066 signs for fire brigade DIN 4067 water; Signs, local water distribution and water pipelines DIN 4068 sewage; Signs DIN 4069 local gas distribution lines; Signs DIN 4073 Planed boards and planks of pine, Part 1 degree since March 2005. WITHDRAWN without replacement DIN 4074 sorting of timber by strength Part 1 softwood lumber Part 2 Quality Conditions for Building Logs (softwood) Part 3 devices to support the visual grading of sawn timber; Requirements and testing Part 4 demonstrate the suitability of the apparatus-supported timber sorting Part 5 hardwood lumber DIN 4076 terms and symbols used on the wooden area Part 1 wood species , Replaced by DIN EN 13556 DIN 4084 Building - Ground failure calculations DIN 4085 Soil - Calculation of earth pressure DIN 4094 building, field investigations
Part 1 CPTs October 2013 Replaced by DIN EN ISO 22476-1 Part 2 Bohrlochrammsondierung Part 3 probing January 2003 Replaced by DIN EN ISO 22476-2 Part 4 wing shear tests Part 5 hole expansion tests in March 2013 Replaced by DIN EN ISO 22476-4 / 5/7 DIN 4095 drainage for the protection of civil structures, planning, design and execution DIN 4102 Fire behavior of building materials and components DIN 4103 Non-load bearing partitions Part 1 requirements, testing Part 2 partitions made of gypsum blocks Part 4 substructure in wood type DIN 4107 Geotechnical Measurements Chapter 1 Basics Part 2 extensometer and convergence measurements Part 3 Inclinometer and deflectometer Part 4 pad pressure measurements DIN 4108 Thermal protection and energy conservation in buildings Part 2 Minimum requirements for thermal protection
Part 3 Air Conditioned moisture protection, requirements, calculation methods and guidelines for plan Part 4 air tightness of buildings - Requirements, planning and design Recommendations, examples. Part 7 air tightness of buildings, requirements, design and construction and Recommendations. Examp Part 8 Prevention of mold growth in residential buildings Part 10 related requirements for thermal insulation materials - Factory made thermal insulation produ DIN 4109 Sound insulation in buildings DIN 4123 Excavations, foundations and underpinnings in the area of ??existing buildings DIN 4124 Excavations and trenches, Slopes, working space widths sheeting, DIN 4126 Verification of stability of diaphragm walls DIN 4128 grouted piles (in-situ concrete and composite piles) with small diameter
DIN 4140 Insulation work on industrial installations in the industry and building equipment - Execution insulations DIN 4149 Buildings in German earthquake areas - Design loads, analysis and structural design of build DIN 4150 shocks in Construction Part 1 Prediction of vibration parameters Part 2 Effects on persons in buildings Part 3 effects to buildings DIN 4159 brick ceiling and cast panels - static mitwirkend DIN 4160 brick ceiling - not static mitwirkend DIN 4172 dimensional coordination in building construction DIN 4185 terms and symbols for screening Part 1 Woven cloth Part 2 perforated plates
Part 3 Cloth-like screens, wedge wire screens and grates DIN 4212 runways of reinforced concrete and prestressed concrete; Design and construction
DIN 4220 Soil Site Assessment - Identification, classification and derivation of soil parameters (normat scaling) DIN 4226 Aggregates for concrete and mortar Part 1 Normal and heavyweight aggregates April 2003 Replaced by DIN EN 12620 Part 2 Lightweight aggregates April 2003 Replaced by DIN EN 12620
Part 3 surcharge for concrete; Examination of aggregates of dense or porous structure , in February 20 4226-1 / 2 Part 100: Recycled aggregates DIN 4261 Small wastewater treatment systems Part 1 The equipment for sewage treatment Part 2 small wastewater treatment plants with vented purification stage , October 2005 Replaced by E Part 3 systems without wastewater aeration - Operation and Maintenance , May, 2004. Replaced by D Part 4 plants with wastewater aeration - Operation and maintenance , October 2005 Replaced by DIN Part 5 Infiltration of aerobic biologically Treated wastewater
Part 101 systems without wastewater aeration - Principles for factory production control and external 2005 Replaced by DIN EN 12566-3 DIN 4262 pipes and fittings for underground drainage of trafficked and civil engineering Part 1 pipes, fittings and Their joints made from PVC-U, PP and PE Part 3 pipes and fittings made of concrete and its compounds DIN 4301 ironworks slag and ferrous slag in construction DIN 4312 industrial turbines, steam turbines and gas expansion; Basis for the construction of industria DIN 4342 gas turbines; standard conditions, standard services, information on operating values DIN 4420 and working scaffolds - Head Scaffolding Safety requirements Part 1 scaffolds - Performance requirements, general design, structural design Part 3 Selected types of scaffolding constructions and Their basic versions DIN 4421 scaffolds - analysis, design and implementation
DIN 4426 Safety requirements for workplaces and accesses - Design and execution (equipment for ma Constructed facilities) DIN 4512 Photographic sensitometry
Part 1 Determination of the sensitivity of black and white negative material for imagewise recordings by ISO 6: 1996-02 Part 3 Determination of the optical density of scattering permeable layers , 1. 1993 Replaced by DIN 4 Part 4 Determination of the sensitivity of color reversal films , 2002-06 Replaced by DIN ISO 2240: 199 Part 5 Determination of the sensitivity of color negative films , 2002-06 Replaced by DIN ISO 5800: 19 Part 6 Sensitometric light sources and light sources. Part 7 Determination of optical density, terms, symbols and markings Part 8 Determination of the optical density; Geometric conditions for measurements in transmission Part 9 Determination of the optical density; Spectral conditions Part 10 Determination of optical density; Geometric conditions for reflection measurements at DIN 4567 Ladders - Design for ladders for special professional use
DIN 4620 spring steel, hot-rolled, with rounded narrow sides of leaf springs ; January, 2004 Replaced b DIN 4701 heat consumption of buildings , Parts 1, 2 and 3 are Replaced by DIN EN 12831 DIN 4702 boiler Part 1 Definitions, requirements, testing, marking Part 2 Rules for Heating tests Part 3 special gas boiler with burner without fan Part 4 boilers for wood, straw and similar fuels; Definitions, requirements, testing Part 6 boilers using gaseous fuels Part 8 Determination of the standard efficiency and the standard emission factor DIN 4703 Space Heater Part 1 Dimensions of member radiators Part 3 Conversion of standard thermal output DIN 4704 Thermal testing of heating appliances DIN 4709 Determination of the standard efficiency for micro-CHP units up to 70 kW of rated load
DIN 4710 Statistics meteorological data to calculate the energy requirements for heating and air cond Germany DIN 4719 residential ventilation - Requirements, performance testing and labeling of air handling unit
DIN 4724 Plastics piping systems for hot water underfloor and radiator connection - Crosslinked mediu polyethylene (PE-MDX)
DIN 4734 Decorative Fireplaces for liquid fuels - Decorative appliances generate using of ethanol-base fuel a flame Part 1 : Terms in the private household sector DIN 4747 district heating systems
Part 1 Safety equipment for substations, stations and domestic systems to be connected to hot-water DIN 4751 boiler equipment , Replaced by DIN EN 12828 DIN 4752 Hot water heating systems with flow Temperatures higher than 110 ° C
DIN 4753 Water heaters and water heating systems for drinking and process water - Requirements, m and testing DIN 4754 Heat transfer systems with organic liquids - Safety requirements and testing DIN 4755 Oil firing installations - Technical regulation installation (TRÖ) - Inspection DIN 4760 form Deviations; Concepts, classification system DIN 4791 heating system; Electrical connector between burner and heat generator DIN 4807 Expansion vessels Part 1 terms, statutory in provisions; Testing and marking
Part 5 Closed expansion vessels with diaphragm for drinking water installations; Requirements, testing labeling; Technical Rules of DVGW DIN 4815 Rubber and plastics hoses for LPG Part 1 tubes with and without inserts Part 2 hoses Part 3 hoses for filling and draining vehicle tanks
Part 4 hoses and hose assemblies for fuel gas installations in vehicles
Part 5 Safety trousers connections and hose connections for removal from liquid pipeline systems - Sa testing and marking DIN 4844 Graphical symbols - Safety colors and safety signs Part 1 Design principles for safety signs in workplaces and public areas Part 2 Overview of safety signs Part 3 Evacuation Maps , December 2010 Replaced by ISO 23601 DIN 4892 Inch - millimeters; Conversion Tables DIN 4893 millimeters - inches; Conversion tables ... DIN 4895 orthogonal coordinate system Part 1: General terms Part 2 differential operators of vector analysis DIN 4896 Simple electrolyte solutions; Symbols DIN 4902 Industrial trucks, hand vehicles and trailers, running gear, symbols, terms, Explanations DIN 4924 sands and gravels for well - Requirements and tests DIN 4926 fountain heads of steel - DN 400 to DN 1200 DIN 4943 Graphical layout and documentation of wells and ground water monitoring wells DIN 4971 Straight turning tool with cutting board made of hard metal DIN 4972 Curved turning tool with cutting board made of hard metal DIN 4973 internal turning tool with cutting board made of hard metal DIN 4974 indoor Eckdrehmeißel with cutting board made of hard metal DIN 4975 peak turning tool with cutting board made of hard metal DIN 4976 width turning tool with cutting board made of hard metal DIN 4977 Remote forehead turning tool with cutting board made of hard metal DIN 4978 Remote Eckdrehmeißel with cutting board made of hard metal DIN 4980 remote side turning tool with cutting board made of hard metal DIN 4981 with nose cutting tool insert of cemented carbide DIN 4991 business forms, framework models for commercial documents (invoices examined as., And o DIN 5000-5999 [ Edit ] DIN 5004 business forms - Unit Conversion DIN 5005 Paper and board - Ringbucheinlagen - hole diameter, hole center distances for the A4 and A DIN 5007 Order of character strings Part 1: General rules for the preparation (ABC Rules) Part 2 Heading rules for the alphabetical order of names DIN 5008writing and design rules for text processing examined. as thedate format and spelling of num DIN 5009 Diktierregeln Communication Withdrawn DIN 5012 letter, October 2008 without replacement Withdrawn DIN 5013 pendant letter, October 2008 without replacement DIN 5030 Spectral measurements Part 1 concepts, quantities, measures Part 2 radiators for spectral irradiance measurements; Selection Criteria
Part 3 Spectral separation; Terms and labeling features Part 5 physical detectors for spectral measurement of radiation; term, characteristics, selection criteri DIN 5031 Optical radiation physics and illuminating engineering Supplement 1 table of contents quantities, symbols and units as well as the index to DIN 5031-1 and Part 1 quantities, symbols and units of radiation physics Part 2 evaluation of radiation by recipient Part 3 quantities, symbols and units of lighting technology Part 4 efficiencies Part 5 temperature terms Part 6 pupil light intensity as a measure of retinal illumination Part 7 Designation of the wavelength ranges Part 8 Radiation terms and constants Part 9 luminescence terms Part 10 Photobiologically effective radiation, quantities, symbols and actions DIN 5032 Photometry Part 1 Photometric method Part 2 operating electrical lamps and measuring the CORRESPONDING sizes Part 3 measurement conditions for gas lights Part 4 measurements on lamps Part 6 photometer, Terms, characteristics and Their classification, Oct. 2004 Replaced by DIN EN 1303 Part 7 Classification of illuminance and luminance measuring instruments Part 8 Data Sheet for illuminance measuring instruments DIN 5033 color measurement Part 1 Basic Concepts of colorimetry Part 2 tristimulus system Part 3 colorimetric Part 4 spectral Part 5 equals method Part 6 tristimulus method Part 7 measuring conditions for object colors Part 8 measuring conditions for light sources Part 9 standard for calibration for colorimetry and photometry DIN 5034 daylight indoors Part 1: General requirements Part 2 Basics Part 3 Calculation Part 4 Simplified determination of minimum window sizes for living rooms Part 5 measurement Part 6 Simplified determination of dimensions Suitable for skylight openings in roof areas DIN 5035 Artificial lighting Part 1 Definitions and general requirements, September 2002 Replaced by DIN EN 12665
Part 2 Guideline values ??for workplaces indoors and outdoors, October 2007 Replaced by EN 12464-1 Part 3 Interior lighting with artificial light; Lighting in hospitals
Part 4 Interior lighting with artificial light; Specific Recommendations for lighting in educational establ 2007 WITHDRAWN without replacement, since March, 2003 Largely superseded in DIN EN 12464-1 Part 5 Interior lighting with artificial light, Emergency lighting, August 1999 Replaced by EN 1838 Part 6 lighting measurement and evaluation
Part 7 Interior lighting with artificial light; lighting in rooms with computer workstations and workplace support Part 8 Task lights; Requirements, Recommendations and testing DIN 5036 Radiometric and photometric properties of materials Supplement 1 Table of Contents and Index Part 1 terms, key figures Part 3 methods of measurement for photometric and spectral radiometric characteristics Part 4 Classification DIN 5037 Photometric evaluation of projectors
Supplement 1. Simplified evaluation for film, television and stage spotlight with Rotationally symmetr
Supplement 2 simplified evaluation for film, television and stage lights witheachother to one or two ve symmetrical light distribution DIN 5038 rules on objective photometry (invalid) DIN 5039 light bulbs, lamps - Concepts and Classification DIN 5040 lamps for lighting purposes Part 1 Photometric Characteristics and Classification Part 2 interior lights, Concepts and Classification Part 3 outdoor lights, Concepts and Classification Part 4 lighting headlights; Terms and photometric evaluation variable DIN 5042 combustion gas lamps and lights Part 1 Classification, terms Part 2 Ceramic mouthpieces, dimensions Part 3 gas mantle, dimensions Part 4 gas mantle for street lighting; Requirements and tests Part 5 pilot burner, hanging arrangement, Form A Part 6 pilot burner, vertical arrangement Part 7 fixed nozzles Part 8 nozzles and union nuts for air regulation DIN 5043 Radioactive luminescent pigments and fluorescent colors Part 1 measurement conditions for the luminance and designation of the pigments Part 2 measurement conditions for the luminance and names of fluorescent colors DIN 5044Stationary traffic lights; Lighting of roads for vehicular traffic; General quality characteristics DIN 5045 meter for DIN volumes; Guidelines (invalid) DIN 5060 Packaging - closure of the tube end DIN 5065 Packaging - Plastic closures for metallic tubes
DIN 5090 Packaging - Packaging Bottles DIN 5107 chisel hammer; Cold Chisel DIN 5108 Masonry Hammers DIN 5111 stems wooden hammers to 2 kg DIN 5112 stems wooden hammers over 2 kg Screw DIN 5117 DIN 5128 rubber hammers DIN 5131 hatchets DIN 5132 Beilstiele DIN 5133 chipping hammer DIN 5134 saw blades for wood Part 1 Technical delivery conditions for Band Saw Blades Part 2 Technical delivery conditions for saw blades Part 4 Technical specification for circular saw blades made of tool steel Part 5 Technical specification for circular saw blades with carbide cutting of DIN 5135 wooden stems mallet to 2 kg DIN 5136 Hammers - Technical delivery conditions DIN 5138 Beitelgriffe DIN 5139 Stechbeitel DIN 5145 Planing DIN 5146 scrub plane DIN 5157 set Taps - Two-piece set for pipe threads G 1/16 to G 4 and Rp 1/16 to Rp 4 DIN 5194 Tapered Vierkantschäfte to Bohrwindenwerkzeugen for wood DIN 5200 screws and nuts - angle screwdriver for slotted screws - Dimensions and requirements DIN 5228 flat scraper, Replaced by DIN 8350 DIN 5235 Adjusting pliers DIN 5254 pliers for retaining rings for shafts DIN 5256 pliers for retaining rings for Bores DIN 5340 terms of physiological optics DIN 5381 Identification colors DIN 5401 Rolling bearing parts, balls DIN 5402 Rolling bearing parts Sheet 1 cylindrical rollers Sheet 2 rolls (Withdrawn) Sheet 3 needle rollers DIN 5406 Rolling bearings - Mother fuses, lock washer , Retaining clamp DIN 5412 Cylindrical Roller Bearings DIN 5415 Rolling bearings - Adapter sleeves DIN 5416 Rolling bearings - Withdrawal DIN 5418 Rolling bearings; Dimensions for the mounting DIN 5419 felt rings, felt strips, grooves for rolling bearing housing
DIN 5425 tolerances for the installation of bearings DIN 5426 Rolling bearings - running noise of rolling bearings Part 1 Method for measuring the body sound DIN 5450 standard atmosphere (invalid) DIN 5464 splines wedge flanks - Heavy series DIN 5471 Machine tools; spline shaft and spline profiles with 4 splines, internal centering, dimensions DIN 5472 Machine tools; Spline Shafts and Spline Bore Profiles with 6 splines, internal centering, dime DIN 5473 logic and set theory; Symbols and concepts DIN 5474 characters of mathematical logic DIN 5475 complexes sizes DIN 5477 percent, per mille DIN 5478 standards in graphs DIN 5480 Involute spline shafts Part 1 Basic Concepts Part 2 pressure angle 30 °, overview
Part 3 Pressure angle 30 °, nominal dimensions, measurements, modules 0.5; 0.6; 0.75; 0.8 and 1 Ma DIN 5480-2: 2005-06
Part 4 pressure angle 30 °, nominal dimensions, metrics, module 1.25 March, 2005 Replaced by DIN 5
Part 5 pressure angle 30 °, nominal dimensions, measurements, Module 1.5, March, 2005 Replaced by 06
Part 6 pressure angle 30 °, nominal dimensions, measurements, Module 2 May, 2005. Replaced by DIN
Part 7 pressure angle 30 °, nominal dimensions, measurements, Module 2.5, March, 2005 Replaced by 06
Part 8 pressure angle 30 °, nominal dimensions, measurements, Module 3, March, 2005 Replaced by D
Part 9 pressure angle 30 °, nominal dimensions, measurements, Module 4, March, 2005 Replaced by D
Part 10 pressure angle 30 °, nominal dimensions, measurements, Module 5, May, 2005. Shall be Repla 2005-06
Part 11 pressure angle 30 °, nominal dimensions, measurements, modules, 6 May, 2005. Replaced by 06 Part 12 pressure angle 30 °, nominal dimensions, measurements, modules 8 May, 2005. Replaced by
Part 13 pressure angle 30 °, nominal dimensions, measurements, modules, 10 May, 2005. Replaced b 06 Part 14 pressure angle 30 °, Flankenpassungen, tolerances, March, 2005 Replaced by DIN 5480-1: 200 Part 15 testing and teaching at side fit Modules 2.5 Part 16 pressure angle 30 °, hobs, shaper cutters, broaches DIN 5481 splines with notched edges DIN 5482 gear hub spline involute profiles and profiles Part 1 dimensions, in February 1987 WITHDRAWN without replacement
Part 2 WITHDRAWN profiles for hobs, February 1987 without replacement
Part 3 Zahnlücken- and tooth thickness measurement WITHDRAWN without replacement with measuri cylinder, February 1987 DIN 5483 Time-dependent variable DIN 5485naming principles of physical quantities; Compound words with property and basic words DIN 5486 spelling of matrices DIN 5487 Fourier transform DIN 5488 nominations for time-dependent Processes (February 1964 invalid) DIN 5489 sense of direction and sign in electrical engineering DIN 5490 use of words related, specific, Relatively standardized and Reduced. (In July 2002 Replaced DIN 5491 Mass Transfer DIN 5493 Logarithmic quantities and units Part 1: General principles, quantities and units of Information Theory, July, 2004. Replaced by DIN IEC Part 2 Logarithmic ratios, degree level in Napier and decibel Part 2, Supplement 1, Logarithmic ratios, levels, characters Note on benchmarks and measuring cond DIN 5494 size systems and systems of units (invalid) DIN 5496 thermal radiation of volume sources DIN 5498 Chemical Thermodynamics; symbol (invalid) DIN 5499 calorific value and the calorific value; Terms DIN 5510 Fire protection of rail vehicles Part 1 hazard levels, fire safety measures and certification Part 2 Fire behavior and fire side effects of materials and parts - Classification, requirements and test Part 4 Structural design of vehicles; Safety requirements Part 5 Electrical equipment; Safety requirements
Part 6 Accompanying measures; Function of emergency, information systems, fire alarm systems, fire Safety requirements DIN 5699 Chain Strap for conveyors DIN 5902 tabs for grooveless bottom rails - Dimensions and types of steel DIN 6000-6999 [ Edit ] DIN 6063 threads, Mainly for plastic containers Part 1 Dimensions of buttress threads Part 2 trapezoidal thread, dimensions DIN 6075 Packaging - bottles Part 1 Vichyform 1 Part 2 Vichyform 2 DIN 6080 packaging, reusable wine bottles, 0.75 l burgundy form DIN 6094 Part 3 Packaging - mouth - hole Mouthpieces
Part 5 Product image - Packaging - Mouthpieces - Mouth Pieces for champagne and sparkling wine bot cork stoppers and crown caps Part 8 Packaging - Mouthpieces - Male thread Part 10 Packaging - Mouth Pieces for wide-mouth glass containers - Wulstrandmundstücke
Part 12 Packaging - Mouth Pieces for bottles - Schraubmundstücke 7.5 R for bottles with internal press Part 13 Packaging - Mouthpieces - 2-speed and 3-speed thread Mouthpieces Part 14 Product image - Packaging - Mouth Pieces for bottles - Schraubmundstück 8 G for bottles with DIN 6096 Packaging - 0.75 liter bottle of champagne and sparkling wine DIN 6099 Packaging - crown corks DIN 6106 Packaging - Glass containers - side and bottom cams DIN 6110 Packaging - Reusable jars with a nominal volume of 212 ml, 425 ml, 580 ml, 720 ml DIN 6111 Packaging - Aerosols - for multiple use with not to separate the Intended equipment
DIN 6120 Marking of packaging and packaging materials for recycling purposes - packaging materials packaging Part 1 symbols Part 2 additional designation DIN 6129 Packaging - bottles and tubes made of glass Part 1 General tolerances fully Automatically manufactured bottles Part 2 volume DIN 6130 packaging, Bottles and hollow plastic, general tolerances for weight and volume DIN 6141 Packaging - Containers with lid of fiber (fiber drums) with base and lid made of steel DIN 6160 Anomaloscopes to diagnose red-green color vision defects DIN 6162 deterministic mining the iodine color DIN 6163 colors and color limits for signal lights Part 1 General Part 2 Stationary signal lights on maritime and inland waterways Part 3 signal lights on road vehicles and trams Part 4 signal lights of the train Part 5 Stationary signal lights in public transport Part 6 signal lights on vessels DIN 6164 DIN color chart Supplement 50 color values ??for standard illuminant C Part 1 of the system DIN color chart on the 2 ° standard observer Part 2 specification of color patterns DIN 6167 Description of yellowing of almost white or nearly colorless materials DIN 6169 color reproduction Part 1: General terms Part 2 color rendering properties of light sources in lighting Part 4 Method of Specifying color reproduction in color photography Part 5 Method of Specifying object-based color reproduction in color printing Part 6 Method of Specifying color reproduction in television technology with image capture devices Part 7 Method of Specifying color reproduction in color television film scanning Part 8 Method of Specifying color-based color reproduction in color printing DIN 6170 anaglyph stereoscopy Part 1 Definitions
DIN 6171 colors for traffic signs and traffic control Part 1 color ranges under daylight DIN 6172 metamerism index pairs of samples at change in illuminant DIN 6173 colormatching Part 1 General colormatching Part 2 lighting conditions for average artificial daylight
DIN 6174 Colorimetric evaluation of color coordinates and color differences in the CIELAB color space uniform DIN 6175 color tolerances for automotive coatings Part 1 Unilackierungen Part 2 effect coatings DIN 6176 Colorimetric evaluation of color differences of surface colors nach the formula DIN99 DIN 6198 packaging; Bottles; Euro Form 2 DIN 6199 beer bottle Steinieform 12:33-liter, May, 2004 WITHDRAWN without replacement DIN 6270 combustion engines for general purposes Supplement 1 conversion factors for continuous power at the operating point with respect to the refer
Supplement 2 conversion factors for the specific fuel consumption at operating location opposite the r DIN 6280 Reciprocating internal combustion engines - Generating sets with reciprocating internal com Part 1: General terms Part 2 power design and nameplate Part 3 operating limits for the motor, generator sets and behavior Part 4 speed control and speed characteristics of reciprocating internal combustion engines; Terms Part 5 performance of synchronous generators for the operational unit Part 6 performance of asynchronous operation for the unit Part 7 switching and control devices for the operational unit; Requirements Part 8 performance in the aggregate operational; Terms Part 9 Acceptance Test Part 10 small power generating sets; Requirements and testing DIN 6304 Tommy screws with fixed toggle DIN 6306 Tommy screws with Wi-gag DIN 6331 Hexagon nuts 1,5 d with collar DIN 6340 Washers for clamping devices DIN 6349 three-jaw chuck - Technical delivery conditions DIN 6403 measuring tapes made of steel with winder frames or winder cases DIN 6437 hoe handles Part 1 dimensions, requirements, testing Part 2 lessons DIN 6438 Hand Metal Shears DIN 6439 Trowels DIN 6440 Trowels DIN 6441 plaster trowels
DIN 6444 wood borers; Auger bits DIN 6445 wood borers, drills with ring handle DIN 6450 pin punch DIN 6451 Cross Chisel DIN 6453 Chisel DIN 6458 Drift DIN 6464 wood borers; Auger DIN 6465 scale hammer DIN 6473 Hand saws for metal; Hacksaws DIN 6475 Fäustel Withdrawn DIN 6481 Kistenraspel (replacement for Erfa 6481), standard DIN 6494 Hand saws for metal - Langsägeblätter DIN 6495 Machine saw blades for metal - Blades for hacksaws DIN 6600 containers (tanks) of steel for the storage of water polluting liquids - Proof of compliance DIN 6601 Resistance of materials from containers (tanks) of steel against liquids (positive liquid list) DIN 6607 corrosion protection of underground storage tanks (tanks); Requirements, testing, DIN 6618 Vertical vessels (tanks) of steel Part 1 walled, for the above ground storage of water polluting flammable and non-flammable liquids
Part 2 double wall, without leak detection fluid for the above ground storage of water polluting flamm flammable liquids
Part 3 double walled with leak detection fluid for the above ground storage of water polluting flammab flammable liquids
Part 4 double wall, without leak detection fluid, with external vacuum suction, for above ground storag liquids DIN 6624 overhead tank (tanks) of steel from 1000 to 5000 liters Part 1 walled, for the above ground storage of water polluting flammable and non-flammable liquids Part 2 double, for the above ground storage of water polluting flammable and non-flammable liquids DIN 6625 Round steel tanks for the above ground storage of liquids with a flash point greater than 55 Part 1 of construction and testing Part 2 calculation DIN 6626 Manholes steel tanks for the underground storage of water polluting flammable and non-flam
DIN 6627 shaft collars for brick Manholes for tanks for the underground storage of water polluting flam flammable liquids DIN 6644 packaging, container with lid made ??of steel Part 2 tension ring lever locks Part 4 removable head, stackable, with corrugated beads DIN 6646 Packaging - Drums and containers made of steel - Case Handle DIN 6650 beverage dispensing system Part 1: General requirements Part 2 material requirements Part 3 Safety requirements for construction and installation parts Part 4 Hygiene requirements for construction and installation parts
Part 5 test Part 6 requirements for cleaning and disinfection Part 7 Hygienic Requirements for the Construction of beverage dispensing systems Part 8 Requirements Conducted water systems Part 9 requirements for freestanding water systems DIN 6651 Pneumatic Tube - Modes of operation DIN 6654 Pneumatic tube systems - Graphical symbols DIN 6700 Welding of railway vehicles and parts (6 parts), January 2008 Replaced by DIN EN 15085-1 . DIN 6730 Paper and board - Vocabulary DIN 6738 Paper and board - life classes DIN 6771 Technical drawings
DIN 6773 Heat treatment of ferrous materials - presentation and disclosure of heat-treated parts in dr 2010 Replaced by ISO 15787 DIN 6775 characters pipes for ink drawing instruments (Micro Standard - Test method for ink pen and Part 1 dimensions, marking, June 1990 Replaced by DIN ISO 9175 -1 Part 2 Requirements and test of line widths, June 1990 Replaced by ISO 9175-2 DIN 6776 Technical drawings, lettering, Nov. 2000 replaces by DIN EN ISO 3098 Part 1 characters Part 1, Supplement 1, support networks for type A Part 1, Supplement 1, support networks for type B DIN 6779 principles for technical products DIN 6789 Documentation Scheme DIN 6796 Conical spring washers for screw connections DIN 6797 ratchets May 2003 WITHDRAWN without replacement Serrated lock washers DIN 6798, May 2003 WITHDRAWN without replacement DIN 6799 lock washers (Retaining washers) for shafts DIN 6800 dose measurement method of the test method for photon and electron radiation Part 1 General information on dosimetry of photon and electron radiation after the test method Part 2 dosimetry of high-energy photon and electron radiation with ionization chambers Part 4 Film dosimetry Part 5 thermoluminescence DIN 6802 Neutron Dosimetry Part 1 Special Definitions and Terms
Part 2 conversion factors to calculate the local and personal dose from neutron fluence correction fact protection and Part 3 neutron measurement techniques in radiation protection Part 4 method for personal dosimetry with albedo dosimeters Part 6 Procedure for deterministic mining the absorbed dose with ionization chambers DIN 6809 Clinical dosimetry Part 1 radiation quality of photons - And electron radiation Part 2 brachytherapy enclosed with gamma-emitting radioactive material Part 3 of Diagnostic Radiology
Application of Part 4 X-rays with peak Voltages between 10 and 100 kV in radiotherapy and soft tissue Part 5 use of X-rays with peak Voltages of 100 to 400 kV in radiotherapy Part 6 Application of high-energy photon and electron radiation in percutaneous radiotherapy DIN 6812 Medical X-ray equipment up to 300 kV - Rules of construction for structural radiation protect DIN 6814 terms of radiological technology Part 1 Applications Part 2 Radiation Physics Part 3 dose quantities and unit doses Part 4 radioactivity Part 5 Radiation Protection Part 6 Diagnostic application of X-rays in medicine Part 8 radiotherapy DIN 6827 Logging in medical use of ionizing radiation Part 1 therapy with electron accelerators and X-ray and gamma irradiation facilities Part 2 Diagnosis and therapy with unsealed radioactive materials Part 3 brachytherapy with sealed radioactive sources Part 5 Radiologic Findings Report DIN 6830 X-ray films for use with fluorescent intensifying screens in medical diagnostics Part 1 Sensitometric of fluorescence radiation of calcium tungstate intensifying screens Part 2 Determination of the sensitivity of the average gradient and the veil DIN 6847 medical electron accelerator equipment Part 2 Rules of construction for structural radiation protection Part 5 constancy tests of characteristic features Part 6 Electronic image receptor (EPID) - constancy test DIN 6853 Medical remote-controlled, operated Automatically afterloading equipment Part 2 Radiation protection rules for the establishment Part 3 Requirements for radiation sources Part 5 constancy testing apparatus of quality characteristics DIN 6855 consistency testing nuclear medicine instruments DIN 6858 quality control multimodality imaging Part 1 constancy test PET / CT DIN 6868 Image quality assurance in diagnostic radiology operations (consistency check) DIN 6873 treatment planning systems Part 5 constancy tests of quality characteristics DIN 6875 Special irradiation facilities Part 1 Percutaneous stereotactic irradiation, characteristic features and special test methods Percutaneous stereotactic radiation Part 2 - constancy tests Part 3 fluence-modulated radiotherapy - Of identification, test methods and rules for clinical use Part 4 fluence-modulated radiotherapy - constancy tests DIN 6876-operation of medical magnetic resonance systems DIN 6883-voltage connections with suit; Flat Keys, Dimensions and Application
DIN 6885 type fastenings without taper, keyways , Grooves, Part 1 tall form Part 2 high form for machine tools, Dimensions and Application Part 3 low shape, dimensions and application DIN 6886-voltage connections with suit, wedges, grooves, Dimensions and Application DIN 6887-voltage connections with suit; Nose wedges, grooves, Dimensions and Application
DIN 6888 type fastenings without taper; Woodruff , Dimensions and Application (replacement for DIN partly LON 522). DIN 6892 type fastenings without taper, Keys, calculation and design DIN 6916 Round washers for high-strength bolts in steel structures, June 2005 Replaced by DIN EN 14 DIN 6918 washers, square, wedge shape for high-bolting of profiles in steel structures DIN 6930 stamped steel Part 1 Technical delivery conditions Part 2 General tolerances DIN 6935 Cold bending of flat steel products DIN 7000-7999 [ Edit ] DIN 7052 separation of liquid Mixtures by distillation and rectification DIN 7079 round, metal fused glass plates for pressure load Part 1 For versions with return
DIN 7080 Sight Glass plates made of borosilicate glass for compressive stress without limitation in the range
DIN 7081 Long glass plates made of borosilicate glass for compressive stress without limitation in the range DIN 7150 Geometrical product specifications (GPS) - system of limits and fits Part 2 Limit gauges and gauging for smooth cylindrical work pieces
DIN 7151 ISO standard tolerances for linear dimensions of 1 to 500 mm nominal size, November 1990 ISO 286-1 DIN 7154 Dimensions of fits in fits, unit bore (diameter up to 500 mm) DIN 7155 Dimensions of fits in the system unit shaft (Ø 500 mm) DIN 7157ISO fits; Tolerances, dimensions, fitting tolerances Supplement of fits; Tolerance zones Select by ISO / R 1829 DIN 7160 Dimensions for External dimensions (waves), November 1990 Replaced by DIN ISO 286-2 DIN 7161 Dimensions for internal dimensions (holes), November 1990 Replaced by DIN ISO 286-2 DIN 7168 General tolerances, linear and angular dimensions, shape and position, not for new design, April 1991 DIN 7172 Dimensions of fits (ø 500 mm to 10,000 mm) DIN 7182 measurements, dimensions, tolerances and fits Part 1 Basic concepts, December 1990 Replaced by DIN ISO 286-1 Part 3 interference fits, concepts, July 1988 Replaced by DIN 7190 DIN 7190 interference fits - The calculation and design rules DIN 7200 Punches DIN 7209 Glass Cutter
DIN 7210 Weber pliers (Replaced Erfa 7210, 7211, 7212; standard WITHDRAWN) DIN 7216 Painters spatulas DIN 7226 Scraper DIN 7235 Hand saws for wood; Issue saas, saas fine DIN 7239 Latthammer DIN 7245 Hand saws for wood - stretching saws, saw blades for Frame Saws DIN 7250 grains DIN 7254 Masonry Chisels DIN 7256 Spitzmeißel DIN 7258 Hand saws for wood; Issue saws, jig saw DIN 7261 Workshop filing, shapes, lengths, cross-sections DIN 7262 Sharpening Files, shapes, lengths, cross-sections DIN 7263 Rasps and cabinet files, shapes, lengths, cross-sections DIN 7283 Key Files, shapes, lengths, cross-sections DIN 7284 Files and rasps; Technical delivery conditions DIN 7287 axes and hatchets made of steel; Technical delivery conditions DIN 7294 Axes DIN 7295 ax handles DIN 7331-tubular rivets, two-piece DIN 7332 eyelets for sailcloth DIN 7353 stamps for metal DIN 7355 standard hoists; Steel winches DIN 7405 staple24/6 for office staplers, Staple, clip rod DIN 7444 screws and nuts - Flip Key Ring - Technical specifications DIN 7462 Mallets DIN 7527 steel forgings and machining allowances admissible Part 1 Variations for Open-die Forged wheels Part 2 Variations for Open-die Forged perforated discs Part 3 Deviations for seamless free-form forged rings Part 4 Deviations for seamless open the forged sockets Part 5 Deviations for the open forged, rolled and welded rings Part 6 machining allowances and tolerances for the open forged bars DIN 7603 sealing rings DIN 7604 locking screws with hexagon socket, light version, cylindrical thread DIN 7711 hard rubber; Types DIN 7715 rubber parts, Dimensional tolerances Part 1 articles of hard rubber Part 5 plates and plate products made of soft rubber (elastomer) DIN 7716 products from rubber and rubber - Requirements for storage, cleaning and maintenance DIN 7726 Foams; Concepts and classification DIN 7753 Endless narrow V-belts for Engineering / Automotive Engineering
Part 1 Dimensions Part 2 Calculation of the drives, power values Part 3 dimensions of the belt and pulley groove profiles Part 4 fatigue test DIN 7756 valve threads DIN 7800 tires for bicycles DIN 7815 drop center rims Part 1 for bicycles DIN 7820 tapered rims for motor vehicles and trailers - rim diameter designation 15, 20 and 24 DIN 7864 Elastomeric sheets for waterproofing Part 1 requirements, testing DIN 7865 Elastomeric joint sealing tapes for joints in concrete Part 1 forms and dimensions Part 2 Requirements and testing Part 3 Field of application DIN 7867 V-ribbed belts and discs DIN 7868 Rubber and plastics covered rollers Part 1 Hardness specifications Part 2 surface features Part 3 dimensional, running and shape tolerances DIN 7898 equipment for outdoor sports facilities and halls - Table Tennis Part 1 dimensions, requirements and test methods for tables March, 2005 Shall TO BE REPLACED DIN Part 2 table tennis tables, Nets and posts, dimensions, requirements, testing, June 2005 Replaced by D DIN 7901 Gymnastic equipment Part 1 bars for school gymnastics Part 2 bars for competitions DIN 7902 Gymnastic equipment; turn horses DIN 7903 Gymnastic equipment; Stretching devices Part 1 plug Reck Part 2 Versenkreck Part 3 step stretching Part 4 Horizontal Bar for competitions DIN 7904 Gymnastic equipment; turn bucks, dimensions, requirements, testing DIN 7905 Gymnastic equipment; Hanging rings Part 1 swing rings with adjustment DIN 7906 Gymnastic equipment; Balance Beam DIN 7908 Gymnastic equipment; vaulting boxes: Safety requirements and testing DIN 7909 Gymnastic equipment Gymnastics Bank DIN 7910 Gymnastic equipment; Wall bars DIN 7911 Gymnastic equipment, climbing equipment Part 1 grid conductors, requirements and testing
Part 2 rope climbing facilities DIN 7912 Gymnastic equipment; Gymnastics Part 1 Gymnastics Clubs Part 2 Hoop DIN 7913 Gymnastic equipment; Procedure for the assessment of mats and floor exercise area Part 1 examination of the hardness and damping Part 2 Testing of anti-security DIN 7914 Gymnastic equipment; Matting Part 1 Turnmatte (Aufsprungmatte) Part 2 soft floor mats; Dimensions, safety requirements and testing DIN 7915 Gymnastic equipment Part 1 springboard for school gymnastics DIN 7916 Gymnastic equipment; Floor Exercise areas Part 1 floor exercise mat DIN 7917 Gymnastic equipment; Changing room benches, requirements, testing DIN 7918 Gymnastic equipment; Trampolines Part 1 Bounce Trampoline, requirements Part 2 mx 5.20 of 3.05 meters, Dimensions, requirements and testing DIN 7926 Children games Part 1 concepts safety requirements, testing Part 2 swings, safety requirements, test Part 3 slides, security requirements, testing Part 4 cable cars, dimensions, safety requirements, test Part 5 carousels, concepts safety requirements, testing DIN 7954 fittings; RolledHinges DIN 7968 Hexagon fit bolts with hexagon nut for steel structures DIN 7969 countersunk head screw with hexagon nut for steel structures DIN 7971 cylinder head tapping screws with slot, November 1995 Replaced by DIN ISO 1481 DIN 7975 sheet metal screw connections, Application, typical values ??for core hole diameter DIN 7978 Taper pins with internal thread, Oct. Replaced in 1992 by DIN EN 28736 DIN 7984 screws with internal hexagon, low head DIN 7985 Pan head screws with cross recess. November 1994 Replaced by DIN EN ISO 7045 DIN 7989 washers for steel structures Part 1 Class C Part 2 Product grade A DIN 7990 Hexagon head bolts with hexagon nut for steel structures DIN 7991 countersunk screws with hexagon socket, march Replaced in 1998 by DIN EN ISO 10642 DIN 7992 Hammer screws with large head DIN 7993 round wire snap rings and snap-ring grooves for shafts and Bores DIN 8000-9999 [ Edit ] DIN 8000 Determinants and error and hobs for spur gears with involute basic concepts
DIN 8061 pipes made of unplasticized polyvinyl chloride (PVC-U) - General quality requirements and t DIN 8062 pipes made of unplasticized polyvinyl chloride (PVC-U) - Dimensions DIN 8074 pipes made of polyethylene (PE) - PE 80, PE 100 - Dimensions; Text in German and English
DIN 8075 pipes made of polyethylene (PE) - PE 80, PE 100 - General quality requirements and testing; English
DIN 8076 pressure pipes made of thermoplastic materials - metal and plastic clamp connector for pipe polyethylene (PE) - General quality requirements and testing DIN 8077 pipes made of polypropylene (PP) - PP-H, PP-B, PP-R, PP-RCT - Dimensions DIN 8078 pipes made of polypropylene (PP) - PP-H, PP-B, PP-R, PP-RCT - General quality requirements DIN 8079 pipes Chlorinated polyvinyl chloride (PVC-C) - Dimensions DIN 8080 pipes Chlorinated polyvinyl chloride (PVC-C) - General quality requirements and testing DIN 8119 bridges for truck scales; Loads Part 1 weighbridges; Bridge sizes, maximum capacity up to 20 tons Part 2 weighbridges, truck scales - bridge sizes, maximum load up to 60 t Part 3 weighbridges, rail scales, combined rail and truck scales - bridge sizes, maximum load of up to Part 4 weighbridges; Loads for floor scales and sunken into the floor scales Part 6 weighbridges; Design loads for rail weighbridges and combined rail and truck scales
DIN 8127 weights of accuracy classes E1, E2, F1, F2, M1, M1-2, M2, M3 and M2-3 - Metrological and te requirements (OIML R 111-1: 2004) DIN 8131 Automatic Gravimetric Filling - Metrological and technical requirements - Tests (OIML R 61-1 DIN 8164 bush chain DIN 8165 Conveyor chains with solid pins Part 1 type FV-fold chain, two-chain beach; Not for new designs Part 2 type FV, fixing lugs, terminal degree; Not for new designs Part 3 type FVT Carrying chains with Increased plates; Not for new designs DIN 8167 Conveyor chains with solid pins Part 1 ISO Type M, fold chain, two-beach necklace Part 2 ISO Type M, mounting straps, connection dimensions Part 3 ISO-type MT; Carrying chains with raised tabs DIN 8187 roller chains, European design Part 1 single, double, triple roller chains Part 2 Simple roller chains with attachments, mounting dimensions Part 3 single roller chains with extended pins, connecting dimensions DIN 8188 Roller chains, American Series Part 1 single, double and triple roller chains Part 2 Simple roller chains with attachments, mounting dimensions Part 3 single roller chains with extended pins, connecting dimensions DIN 8263 jewels of fine mechanics, Caps tone for appliances, flat DIN 8350 Scraper DIN 8416 dust collector for commercial use - Safety requirements and testing DIN 8513 brazing alloys , Replaced by DIN EN 1044
DIN 8516 Solderswith rosin-based flux cores; Composition, technical specifications, testing, November by DIN EN ISO 12224-1
DIN 8521 safety devices to prevent prevention gas blowback for the use of gases of public gas supply to a maximum working pressure of 0.1 bar, do not flame-safe Part 2 security requirements, testing DIN 8526 Testing of soldered joints; Spaltlötverbindungen, shear test, creep shear test DIN 8541 hoses for welding, cutting and allied Processes Part 2 hoses with sheathing for fuel gases, oxygen and other non-flammable gases Part 3 oxygen hoses with and without sheathing to special requirements; Safety requirements and tes DIN 8552 Weld preparation - joint preparation of copper and copper alloys Part 3 gas welding and arc welding DIN 8580 manufacturing method DIN 8585 Manufacturing Processes forming under tensile Part 1 General; Classification, subdivision, terms Part 2 lengths; Classification, subdivision, terms Part 3 sizes; Classification, subdivision, terms Part 4 depths; Classification, subdivision, terms DIN 8589 manufacturing process Slicing Part 0 General; Classification, subdivision, terms Part 1 Turn; Classification, subdivision, terms Part 2 drilling countersinking, reaming; Classification, subdivision, terms Part 3 milling; Classification, subdivision, terms Part 4 planing, slotting; Classification, subdivision, terms Part 5 rooms; Classification, subdivision, terms Part 6 saas; Classification, subdivision, terms Part 7 Files, rasps; Classification, subdivision, terms Part 8 Bürstspanen; Classification, subdivision, terms Part 9 cockroaches, chisels; Classification subdivision, terms Part 11 grinding with a rotating tool; Classification, subdivision, terms Part 12 Volume loops; Classification, subdivision, terms Part 13 Hubschleifen; Classification, subdivision, terms Part 14 Honing; Classification, subdivision, terms Part 15 lapping; Classification, subdivision, terms Part 17 Gleitspanen; Classification, subdivision, terms DIN 8593 Manufacturing Processes joining Part 0 General; Classification, subdivision, terms Part 1 assembly; Classification, subdivision, terms Part 2 stuffing; Classification, subdivision, terms Part 3 pressing, pressing, Classification, subdivision, terms Part 4 by joining archetypes; Classification, subdivision, terms Part 5 joining by forming; Classification, subdivision, terms Part 6 joining by welding; Classification, subdivision, terms
Part 7 joining by soldering; Classification, subdivision, terms Part 8 bonding; Classification, subdivision, terms
DIN 8605 Machine tools; Lathes with Increased accuracy, Swing up to 500 mm, length up to 1500 mm conditions DIN 8606 Machine tools; Lathes of Normal Accuracy, Swing up to 800 mm, acceptance conditions
DIN 8607 Machine tools; Lathes of Normal Accuracy, Swing diameter over 800 up to 1600 mm, accept DIN 8609 Machine tools; Vertical lathes, acceptance conditions Part 1: General introduction Single column vertical lathes Part 2, acceptance conditions Part 3 double column vertical lathes, acceptance conditions DIN 8610 Machine tools; turret lathes, hand operated, acceptance conditions, withdrawal without repl DIN 8611 Machine tools; Horizontal lathes Part 1 single spindle, acceptance conditions Part 2 front operated, acceptance conditions Part 3 lathes, acceptance conditions DIN 8615 Machine tools; Milling Machines Part 1 WITHDRAWN with horizontal spindle and height-adjustable console, acceptance conditions, with Part 2 WITHDRAWN vertical-spindle height-adjustable console, acceptance conditions, without replace Part 3 with horizontal spindle and fixed table, acceptance conditions Part 4 with vertical spindle and fixed table, acceptance conditions DIN 8620 Machine tools; horizontal drilling milling machines with table and fixed state, Part 3 turntables, acceptance conditions DIN 8625 Machine tools; radial drilling machines with movable boom Part 1 acceptance conditions DIN 8626 Machine tools; Vertical Drilling Part 1 drill presses, acceptance conditions Part 2 column drills, acceptance conditions DIN 8630 Machine tools; Cylindrical grinding machines with movable worktable; Acceptance condition DIN 8634 Machine tools; Centerless external cylindrical grinding machines; Acceptance conditions DIN 8659 Machine tools; Lubrication of machine tools Part 1 lubrication instructions Part 2 Selection of lubricants for metal cutting machine tools DIN 8743 Packaging machinery and equipment - Time-Related Terms, characteristics and calculation b DIN 8757 Millstones, horizontally Continuously; Issue August 1948 WITHDRAWN Standard DIN 8782 beverage bottling equipment, bottling lines and Terms for individual units DIN 8783 beverage bottling equipment; Studies on filling installations DIN 8784 beverage bottling equipment; minimum information and order-related information DIN 8806 band saw blade DIN 8901 Refrigerating systems and heat pumps - protection of soil, groundwater and surface water environmental requirements and testing
DIN 8902 Sight Glass plates made of soda-lime glass for compressive stress without limitation in the l range DIN 8903 Long sight glasses of soda-lime glass for compressive stress without limitation in the low tem DIN 8905 tubes for refrigeration systems with hermetic and semi-hermetic compressorsPart 1 outside diameter up to 54 mm; Technical delivery conditions Part 3 Additional technical delivery conditions for capillary restrictor tubes DIN 8906 Refrigeration, Soldering compression fittings with flanged pipe, PN 40 DIN 8912 Refrigeration; Union nuts, plugs for solderless tube fittings with rolled pipe, PN 40 DIN 8915 Mobile refrigeration equipment - Safety requirements and testing
DIN 8927 Open compressors for refrigerators; standard conditions on measurement, testing, data cha sheets and nameplates DIN 8930 Refrigerating systems and heat pumps - Terminology Part 5 Contracting DIN 8941 symbols, units and indices for refrigeration DIN 8948 desiccant for drying Refrigerants - Testing DIN 8956 Commercial freezers for deep frozen foodstuffs; Definitions, requirements, testing DIN 8958 performance testing of cooling equipment for insulated Means Part 1 transport refrigeration system with forced air cooler Part 2 transport refrigeration systems with eutectic elements, dry ice and cryogenic, liquid gas Part 3 transport cooler with dry ice (Draft) Part 4 gas cooling equipment with direct evaporation (Draft) Part 5 gas cooling system with indirect evaporation (draft) DIN 8960 Refrigerant - Requirements and abbreviations DIN 8964 circuit parts for refrigeration system Part 1 exams Part 2 Permanently closed system; Requirements Part 3 Closed systems; Requirements
DIN 8971 Single-stage condensing units for refrigeration; standard conditions for performance data; E characteristic information in datasheets and nameplates
DIN 8973 motor-compressors for refrigerators; standard conditions for performance data; Examination information in datasheets and nameplates DIN 8974 Duration switching hermetic motor compressor test for refrigeration systems; Test condition DIN 8975 refrigeration systems - Safety principles for design of equipment and installation Part 1 Interpretation DIN 8976 performance test of compressor chillers DIN 8978 Wear testing of Refrigerant compressors DIN 8979 High Temperature Testing Engine compressors in refrigeration systems DIN 8994 piano action; Dimensions DIN 9088 Aerospace - storage times of elastomer-based products DIN 9020 mass breakdown for aircraft heavier than air Part 2 mass main groups and mass terms Part 3 group mass Lineup
DIN 9300 Aerospace; Concepts, quantities and symbols for flight mechanics Part 1 motion of the aircraft relative to the air Part 2 movements of the aircraft and the atmosphere relative to the Earth Part 3 Derivatives of forces, moments and Their Beiwerten 5 sizes and measurements Part 6 geometry of the aircraft Part 7 points and airline flight operations areas DIN 10000-14999 [ Edit ]
DIN 10106 Microbiological examination of meat and meat products; Determination of Enterococcus fa Enterococcus faecium; Spatula method (Reference method)
DIN 10109 Microbiological examination of meat and meat products; Determination of aerobically grow bacteria; Spatula method (Reference method) DIN 10113 Determination of surface colony count on fitment and utensils in the food sector Part 1 Quantitative swab method Part 2 Semiquantitative swab method Part 3 Semiquantitative method with culture media laminated taking up equipment (squeeze method)
DIN 10122 Analysis of foodstuffs - Enumeration of microorganisms by impedance method - Determina colony count DIN 10192 Microbiological analysis of milk - Enumeration of bacteria Part 5 spatula DIN 10510 process DIN 10511 DIN 10512 DIN 10514 DIN 10516 DIN 10518
Food hygiene - Commercial dishwashing with multi-tank conveyor dishwashers - Hygiene r
Food hygiene - Commercial glass washing machines with glasses - Hygiene requirements, Food hygiene - Commercial dishwashing with single-tank dishwashers - Hygiene requireme Food hygiene - training hygiene food hygiene - cleaning and disinfection Food hygiene - Production and direct sale of ice cream to the consumer - Hygiene requirem
DIN 10521 Food hygiene - Independent budget line water filter - Household water filter on the basis o and activated carbon
DIN 10522 Food hygiene - Commercial cleaning of reusable boxes and reusable containers for unpack requirements, testing DIN 10523 Food hygiene - Pest control in the food industry DIN 10524 Food hygiene - Work wear in food business; text in German, English and French DIN 10526 Food hygiene - Retained samples in mass catering DIN 10527 Food hygiene - Sale of perishable foodstuffs from vending machines - Hygiene requiremen DIN 10528 Food hygiene - Guidance for the selection of materials used in contact with food stuffs - Ge DIN 10529 dosing for oral administration of powdered or liquid finished drugs in livestock Part 1 dosing for powdery proprietary medicinal products for application about powdery feed Part 2 dosing for liquid proprietary medicinal products for administration via drinking water
DIN 10766 Analysis of coffee and coffee products; The water content of green coffee, Dioxandestillatio titration DIN 10950 Sensory analysis - General principles
DIN 10955 Sensory analysis - Testing of packaging materials and packaging for food DIN 10956 sensory analysis - Universal testing glasses and lids - Requirements and application guide DIN 10959 Sensory analysis - Determination of sensitivity of taste DIN 10960 sensory analysis - Test lenses for wine DIN 10967 Sensory analysis - Investigation of profiles Part 1 Conventional profiles Part 2 consensus profiles Part 3 Free Choice profiles Part 4 test plan DIN 11540 peat and peat products for horticulture and landscaping - Test methods, properties, technic DIN 11622 silage and liquid manure tank Part 1 rating, design, texture; General requirements
Part 2 rating, design principles - Silage and liquid manure containers made of reinforced concrete, pre concrete, concrete blocks and concrete hollow blocks Part 4 rating, design, texture, Above-ground silage and liquid manure tanks made ??of steel Part 22 concrete shuttering blocks DIN 11850 Pipes for food, chemical and pharmaceutical industry - tubes of stainless steel - Dimension DIN 11851 Stainless steel fittings for food and chemical industry - Tube Fittings for expanding and wel
DIN 11852 Fittings for the food and chemical industries - Fittings of stainless steel - Tees, elbows and r DIN 11864 Stainless steel fittings for aseptic , Chemical and pharmaceutical Part 1 Aseptic tube fittings, standard type Part 2 aseptic flange connection, standard version Part 3 Aseptic clamp connection, standard version DIN 11865 fittings made of stainless steel for aseptic, chemical and pharmaceutical DIN 11866 stainless steel tubes for aseptic, chemical and pharmaceutical industry DIN 12116 Testing of glass - Resistance to a boiling aqueous hydrochloric acid solution - Testing and cl DIN 12242 Laboratory glassware; Conical ground for interchangeable links Part 1 dimensions, tolerances DIN 12244 Laboratory glassware; Spherical Joints for interchangeable links Part 1 dimensions, tolerances DIN 12245 Laboratory glassware; Cone sleeves taper 1: 10, sanded or roughly, dimensions, tolerance DIN 12249 Laboratory glassware; Connectors with NS sections DIN 12252 Laboratory glassware; Plugs with conical ground DIN 12254 Laboratory Equipment made of plastics; Stoppers for conical ground sockets DIN 12256 Laboratory glassware; Leak testing of tapered ground joints, spherical ground connections DIN 12257 Laboratory glassware; Adaptors DIN 12263 terminals for spherical ground connections DIN 12264 Laboratory glassware; Connectors with spherical joint
DIN 12330 laboratory equipment made of quartz glass (silica glass) and quartz (fused silica); Cup of q glass) DIN 12331 Laboratory glassware; Cup
DIN 12336 Laboratory glassware; Evaporating dishes with flat bottom DIN 12337 Laboratory glassware; Crystallizing without spout DIN 12338 Laboratory glassware; Crystallizing with spout DIN 12340 Laboratory glassware; low doses hinged DIN 12341 Laboratory glassware, glasses Watch DIN 12392 Laboratory glassware; reaction flask DIN 12394 Laboratory glassware; distillation flask DIN 12600 Volumetric for laboratory use; Conformity assessment and attestation of conformity DIN 12602 Laboratory glassware; Soxhlet extractors, with cone sections DIN 12604 Laboratory glassware; Hot-extractors with cone sections DIN 12605 Laboratory glassware - weighing bottles DIN 12790Laboratory glassware; hydrometer foundations for construction and adjustment DIN 12791 Laboratory glassware - Density hydro meters Part 1: General requirements Part 2 standard sizes, designation Part 3 Use and examination DIN 12876 Electrical Laboratory Instruments - Laboratory Thermostats and laboratory baths Part 1 Definitions and classification Part 2 Determination of the characteristics of heating and cooling thermostat Part 3 Determination of the characteristics of laboratory baths
DIN 12878 Electrical laboratory equipment; Adjustable liquid-glass contact thermometers and controll safety requirements and testing DIN 12880 Electrical laboratory equipment - Heat and Incubators DIN 12889 laboratory equipment; Three feet DIN 12890 laboratory equipment; Spatula DIN 12892 Laboratory Equipment made ??of metal; stand bases DIN 12893 Laboratory Equipment made ??of metal; Support rods DIN 12894 Laboratory Equipment made of metal - Clamps DIN 12895 Laboratory Equipment made of metal; Tripod sockets Part 1 Double sockets, fixed and rotatable base Part 2 Hook Connector DIN 12897 Laboratory Equipment made ??of metal, lifts, safety requirements test, DIN 12898 Laboratory taps; Hose DIN 12899 Emergency safety Part 3 of showers for farms and terminals DIN 12927 Laboratory equipment - Suction boxes with air recirculation - Requirements, tests DIN 12950 laboratory facilities; Safety Cabinets for microbiological and biotechnological work; Part 1 Safety requirements and testing, Oct. Replaced in 1991 by DIN 12950-10
Part 2 retention capacity of safety cabinets Class 1 and Class 2, microbiological testing, Oct. Replaced 12950-10
Part 3 product protection of safety cabinets Class 2; Microbiological testing (Draft), March 1990 Replac
Part 4 contamination protection in safety cabinets Class 2; Microbiological testing (Draft), March 1990 12950-1 Part 10 requirements, testing, September 2000 Replaced by DIN EN 12469 DIN 13024 stretcher Part 1 With fixed poles; Dimensions, requirements, testing Part 2 With foldable spars; Dimensions, requirements, testing DIN 13050 Rescue - Vocabulary DIN 13061 shin guards for soccer players
DIN 13071 restraint systems for patients in the hospital room - Definitions, requirements, testing, Feb WITHDRAWN without replacement DIN 13080 Division of hospitals into functional areas and functional sections DIN 13090 plug and plug connections for medical devices Part 4 Lock fittings for endoscopes DIN 13155 emergency medical suitcase DIN 13157 First Aid Kit - First Aid Kit C (Small first aid kit) DIN 13160 First Aid Kit - medical bags (Or medical totes, for the civil protection / MCI case) WITHDRAW DIN 13164 First Aid Kit - First Aid Kit B (car kits) DIN 13169 First Aid Kit - First Aid Kit E (Large first aid kit) DIN 13182 Medical instruments - bile duct terminals by Lahey and after Gray DIN 13201 street lighting Part 1 Selection of lighting classes; German version CEN / TR 13201-1: 2004 DIN 13232 emergency equipment DIN 13233 Doctor's Emergency Case for infants and young children, May 2011 Replaced by DIN 13232 DIN 13260 Supply Systems for Medical Gases DIN 13303 Stochastics Part 1 Probability Theory, Common basic concepts of mathematical and descriptive statistics; Vocabul Part 2 Mathematical Statistics, Vocabulary and symbols DIN 13304 representation of symbols on Einzeilendruckern and visual display units (1996 WITHDRAWN DIN 13312 Navigation - Terms, abbreviations, symbols, graphic symbols DIN 13317 rigid body mechanics; Concepts, quantities, symbols DIN 13320 Acoustics; Spectra and transmission curves, Concepts, representation DIN 13343 linear viscoelastic substances; Concepts, constitutive equations, basic functions DIN 13345 thermodynamics and kinetics of chemical reactions; symbol units DIN 13601 diphtheria serum - terms, unit, testing, marking (invalid) DIN 14010 specifications for the statistical monitoring of fires DIN 14011 promoting extinguishing water from the fire water extraction point to the fire DIN 14033 Abbreviation for firefighters DIN 14034 Graphical symbols for fire-brigade DIN 14035 Roof labeling for firefighting vehicles; Execution DIN 14090 land for firefighters DIN 14092 Fire stations Part 1 Planning Basics
Part 3 Feuerwehrturm Part 7 workshops DIN 14093 Respiratory protection exercise facilities Part 1 Planning Basics DIN 14094 Fire Fighting - Escape ladder Part 1 Escape ladder with and without falling protection, holding device, platform Part 2 escape routes on flat and sloping roofs DIN 14095 Fire Department plans for buildings DIN 14096 Fire Safety Regulations DIN 14142 First Aid Kit - First aid kit for fire vehicles DIN 14151 Rescue blankets Part 1: General requirements, test Part 2 Sprungtuch 8 - Requirements, testing, Part 3 leap pad 16; Requirements, testing, DIN 14210 fire water pond DIN 14220 extinguishing water fountain DIN 14230 underground water tank DIN 14244 extinguishing water suction connections - Floor and underfloor DIN 14301 D-pressure suction coupling PN 16 aluminum alloy DIN 14302 C-pressure coupling PN 16 aluminum alloy DIN 14303 B-clutch pressure PN 16 aluminum alloy
DIN 14318 B coupling with metal sealing surface PN 16, made of aluminum alloy and B-Deck capsule, aluminum alloy
DIN 14319 A tight coupling with metal sealing surface PN 16, made of aluminum alloy and A-Deck cap iron or aluminum alloy DIN 14321 C-suction coupling PN 16, made of aluminum alloy DIN 14322 B-Suction coupling PN 16 aluminum alloy DIN 14323 A pressure-suction coupling PN 16, made of aluminum alloy DIN 14341 CD-adapter PN 16 aluminum alloy DIN 14342 BC adapter PN 16 aluminum alloy DIN 14343 AB adapter PN 16 aluminum alloy DIN 14345 distributor DCD-C, B-CBC and CBC-BB, PN 16 DIN 14375 standpipe PN 16 Part 1 standpipe 2 B DIN 14406 portable fire extinguisher April Replaced in 1992 by DIN EN 3 DIN 14420 fire pumps In November 2002 Replaced by EN 1028-1 Part 2 Tragkraftspritzen DIN 14421 pressure gauges (gauge) for fire pumps
DIN 14424 Firefighting equipment - Explosion-proof portable transfer pump with electric motor - Requ testing
DIN 14427 Firefighting equipment - Explosion-proof portable hazardous transfer pump with electric m testing,
DIN 14461 fire-hose connection devices Part 1 wall hydrant with semi-rigid pants Part 2 Filling station and output Means for extinguishing water pipes "dry" Part 3 Landing valves PN 16 Part 4 Building supply PN 16 of fire extinguishing pipe Part 5 tapping valve PN 16 for fire mains Part 6 Dimensions of cabinets and installation of fire hose with flat hoses nach DIN EN 671-2 DIN 14462 extinguishing water facilities - Design and installation of fire hose systems and fire water li DIN 14463 firewater systems - remote controlled filling and draining devices Part 1 For hose reel system Part 2 For water extinguishing systems with empty and pressure pipework; Requirements and test me Part 3 Air Valves PN 16 of fire extinguishing pipe DIN 14489 sprinkler systems; General principles DIN 14494 deluge systems, fixed, with open nozzles DIN 14495 sprinkling of aboveground tanks for storage of flammable liquids in case of fire DIN 14497 Small fire extinguishing systems - Requirements, testing, DIN 14502 Fire trucks(General Requirements), for the part 1 see DIN EN 14502-1 Part 2 Additional in provisions to DIN EN 1846-2 and EN 1846-3 (Proposal for a European standard) Part 3 colors and special markings DIN 14503 Fire Department trailers, uniaxially 2003 Replaced by DIN 14521 DIN 14505 Wechsellader vehicles (WLF) DIN 14507 Einsatzleitwagen Part 1 General requirements for Einsatzleitwagen Part 2 Einsatzleitwagen 1 (ELW 1) Part 3 Einsatzleitwagen 2 (ELW 2) Part 4 Einsatzleitwagen 3 (ELW 3) WITHDRAWN, Part 5 Kommandowagen (KdoW), until 1999 called ELF-K DIN 14520 portable pump trailer 1992 WITHDRAWN DIN 14521 Fire Fighting - pendant with sparkling water cannons DIN 14530 firetrucks, For parts 1-3 see DIN EN 14530
Part 5 Löschgruppenfahrzeug 10 (LF 10) Previously 2002-2012 Löschgruppenfahrzeug 10/6 (LF 10/6) o Löschgruppenfahrzeug 10/6 (HLF 10/6), formerly (until 2002)Löschgruppenfahrzeug 8/6 (LF 8/6) Part 7 Löschgruppenfahrzeug 8 (LF 8)
Part 8 Löschgruppenfahrzeug 20 for Civil Protection (LF 20 KatS) Previously Löschgruppenfahrzeug 16 (LF 16-TS) Part 9 Löschgruppenfahrzeug 16 (LF 16) Part 10 Löschgruppenfahrzeug 24 (Prestandard 1987-1991) In 1991 WITHDRAWN
Part 11 Löschgruppenfahrzeug 20 (LF 20) to 2005 Löschgruppenfahrzeug 16/12 (LF 16/12), 2005-2012 Löschgruppenfahrzeug 20/6 ((H) LF 20/16) called Part 16 portable pump vehicle (TSF) Part 17 portable pump vehicle with water (TSF-W)
Part 18 Tanklöschfahrzeug 2000 (TLF 2000), since October 2011, formerly (until 1991) Tanklöschfahrze Part 20 Tanklöschfahrzeug 16/25 (TLF 16/25), 2005 WITHDRAWN
Part 21 Tanklöschfahrzeug 4000 (TLF 4000) 2005 - April 2011 Tanklöschfahrzeug 20/40 (TLF 20/40 or w extinguishing agents TLF 20/40 SL) Previously Tanklöschfahrzeug 24/50 (TLF 24/50) Part 22 Tanklöschfahrzeug 3000 (TLF 3000), until April 2011 fire truck 16/24 with troop crew (TLF 16/2 Part 24 Small Fire Truck (Germany) Fundamentally revised (KLF), 2012 Part 25 Mean fire engine called (MLF), in September 2012 Season firetruck 10/6 (10/6 StLF) Part 26 assistance Löschgruppenfahrzeug 10 (HLF 10) Part 27 assistance Löschgruppenfahrzeug 20 (HLF 20) DIN 14555 Rüst - And Trolleys Part 1: General requirements Part 2 Rüstwagen 1 (RW 1) WITHDRAWN in 2002 on Part 3 Rescue Vehicle , Up to 2002 Rescue Vehicle 2 (RW 2) Part 4 Rüstwagen 3 (RW 3), 2002 what WITHDRAWN Part 10 Trolley (GW), 1974 - May 1990 (WITHDRAWN) Part 11 Trolley oil (GW-oil), August 1978 - May 1990 (WITHDRAWN)
Part 12 Trolley dangerous (GW-G), since 2005 October 1990 - October 1997 Trolley Dangerous 2 (GW-G April 2005 Trolley Dangerous 3 (GW-G 3) Part 13 Trolley dangerous 1 (GW-G 1), April 1992 - October 1997 (in favor of part 14 is Retracted) Part 14 Trolley dangerous 1 (GW-G 1) October 1992 - April 2005 (WITHDRAWN) Part 21 trolley Logistics 1 (GW-L 1), since 2012 Part 22 devices for logistic 2 (GW-L 2), since 2012 DIN 14565 Hose Reel 2000 troop occupation (Tr SW 2000), 2005 Replaced by DIN 14555-22 DIN 14572 exhaust pipes and exhaust pant connectors DIN 14584 Fire trucks - Mechanically propelled traction devices - Requirements, testing, DIN 14610 Audible warning devices at preferential Wegbenutzern DIN 14623 Signs for orientation at automatic fire detectors DIN 14662 Firefighting equipment - Fire brigade display panel for fire alarm systems DIN 14675 fire alarm systems
DIN 14676 Smoke alarms for homes, apartments and rooms with similar purposes - Installation, Opera Maintenance DIN 14677 maintenance of electrically controlled hold-open systems for fire and smoke barriers DIN 14701-2 rise aerial appliances; turntable ladders (DL) Mechanically propelled 2006 Replaced by D DIN 14702 turntable ladder DL 16-4 with manual drive WITHDRAWN, DIN 14703 attachments conductors (AL), WITHDRAWN in 2007 DIN 14710-1 Hook ladder made of wood with folding hooks 2001 Replaced by DIN EN 1147 DIN 14711 connector manager In 2001, Replaced by DIN EN 1147 DIN 14713 folding ladder In 2001, Replaced by DIN EN 1147 DIN 14714 two-piece extension ladder In 2001, Replaced by DIN EN 1147 DIN 14715 three-part extension ladder in 2001 Replaced by DIN EN 1147 DIN 14811 Fire Hoses - pressure hoses and hose assemblies for pumps and vehicles
DIN 14822 Coupling wrench for firefighting equipments Part 1 coupling key BC Part 2 Clutch key ABC DIN 14853 crowbar DIN 14920 Fire Department leash - Requirements, testing, treatment DIN 14921 Fire Department Canvas Bag DIN 14922 Fire Department multipurpose bag DIN 14924 fireman with dust bag DIN 14925 Fire Fighting; Locking device DIN 14961 vessels of firefighters: Barque (MPE) and rescue boat (RTB) DIN 14962 Boat Trailer [Trailer] for firefighters watercraft DIN 15000-17999 [ Edit ] DIN 15001 Cranes; Terms, Part 1 Classification by type Part 2 Classification by use DIN 15002 hoists, lifting equipment designations DIN 15003 hoists, lifting equipment loads and forces, concepts DIN 15012 hoists; Symbols for operator controls of control devices DIN 15018 Cranes; Principles for steel structures Part 1 calculation Part 2 Principles of structural design and execution Part 3 Calculation of mobile cranes DIN 15019 Cranes; Stability Part 1 of jurisdiction for all cranes except trackless mobile cranes and floating cranes except Part 2 Stability for trackless mobile cranes, and test load calculation DIN 15020 hoists; Principles for Rope Drives Part 1 Design and construction Part 2 monitoring in use DIN 15021 hoists; Capacities DIN 15022 Cranes; Heights, working speeds DIN 15023 Cranes; gantry cranes Cranes and with cantilever overhangs DIN 15024 Series cranes and hoists; track center dimensions for double girder trolleys DIN 15025 Cranes; operation sense and arrangement of controls in crane cabins DIN 15026 hoists; marking danger areas DIN 15030 hoists; Acceptance testing of cranes, principles DIN 15049 crane with electric hoist or similar lifting gear, wheels with bearings DIN 15050 cranes with manual surgery; Wheels with roller bearings DIN 15053 Cranes; transmission, connection dimensions, Umgrenzungsmaße, output torque DIN 15055 Metallurgical equipment and cranes; Pressure oil interference fits, Application, dimensions, DIN 15057 Cranes; cap, fitting dimensions DIN 15058 hoists; Achshalter
DIN 15061 Cranes; Groove profiles Part 1 Groove profiles for pulleys Part 2 groove profiles for cable drums DIN 15062 Cranes; Sheaves Part 1 rows selection and assignment of proper diameter and overall width dimensions Part 2 dimensions for hubs and bearings DIN 15063 hoists, pulleys, technical specifications DIN 15069 hoists; Thrust washers DIN 15070 Cranes; Basis of calculation for wheels DIN 15071 Cranes; Calculation of bearing stress on the wheels DIN 15072 Cranes; Tread profile of the wheels and assignment of crane rails for impeller diameter DIN 15073 Cranes; Wheels, overview ; DIN 15074 Cranes sprocket wheels with flanges, with slide bearing, without DIN 15075 Cranes; Wheels with flanges, with slide bearing, with ring gear ; DIN 15076 Cranes sprocket wheels with flanges and tires, with slide bearing without, DIN 15077 Cranes; Wheels with flanges and tires, with slide bearing, with ring gear DIN 15078 Cranes; Wheels with flanges, with roller bearings, without gear DIN 15079 Cranes; Wheels with flanges, with roller bearings, with gear DIN 15080 Cranes; Wheels with flanges and tires, with roller bearings, without gear DIN 15081 Cranes; Wheels with flanges and tires, with roller bearings, with gear DIN 15082 Cranes; Wheels Part 1 can be flanged sprockets Part 2 wheels with roller bearings, pressed on sprockets DIN 15083 Cranes; Wheels, tires Machined DIN 15084 Cranes; Wheels with roller bearings, locking lid DIN 15085 hoists, Wheels, technical specifications DIN 15086 Cranes; Wheels with roller bearings, flattening of the inner bushings DIN 15090 Cranes; Fuel and idler wheel; Compilation DIN 15091 Cranes; Fuel and idler wheel; impeller shafts DIN 15092 Cranes; Fuel and idler wheel; Cap DIN 15093 Cranes; Fuel and idler wheel; Wheels DIN 15094 Cranes; Fuel and idler wheel, bearing rings Basket DIN 15095 Cranes; Fuel and idler wheel, lock washers, bushings, nipples DIN 15100 Series lifting equipment; Appointments DIN 15105 Lifting hooks for lifting appliances; Hook fastenings DIN 15106 Lifting hooks for lifting appliances; hook safety latch for single hooks DIN 15112 balancers; Safety requirements and testing DIN 15141 transport chain; Pallets; Four-way wooden pallets window Part 4 brewery pallets 1000 mm x 1200 mm DIN 15142 Material Handling Equipment, box pallets, post pallets Part 1 Main dimensions and stackers
DIN 15146 four-way flat wooden pallets Part 4 800 mm × 600 mm DIN 15147 flat pallets of wood; Quality Conditions DIN 15170 industrial trucks, trailer hitches; Connecting dimensions, requirements, testing DIN 15172 powered industrial trucks, tug and towing trucks, traction, trailer DIN 15185 with bearing guided industrial trucks Part 1: Requirements floor, warehouse and other requirements Part 2: Personal protection in the use of industrial trucks in narrow aisles; Safety requirements and tes DIN 15190 freight container; Inland Container Part 101 main dimensions, corner fittings, testing Part 102 enclosed, DIN 15201 Continuous handling Part 1 terms Part 2 accessory equipment, Names, image examples DIN 15207 Continuous handling equipment - Idlers for belt conveyors Part 1 Main dimensions of the support rollers conveyors for bulk materials Part 2 Main dimensions of the support rollers for cargo conveyor DIN 15209 Continuous handling equipment; buffer rings for ring buffer rollers for belt conveyors DIN 15210 Continuous handling equipment, support rings for supporting ring rollers for belt conveyors DIN 15221 Facility Management Part 1 Definitions Part 2 Guide to prepare Facility Management agreements Part 3 Guidelines for quality in Facility Management Part 4 Taxonomy, Classification and Structures in Facility Management Part 5 Guide for Facility Management Processes Part 6 Size Measurement in Facility Management Part 7 Guidelines for Performance Benchmarking DIN 15231 Continuous handling equipment, elevator, flat cup DIN 15232 Continuous handling equipment, elevator, flat round cup DIN 15233 Continuous handling equipment, Elevator, agents cup depth DIN 15234 Continuous handling equipment, Elevator, depth mug with a flat rear wall DIN 15235 Continuous handling equipment, Elevator, depth mug with a curved rear wall DIN 15236 Continuous handling equipment; Elevator Part 1 cup attachment to belts Part 2 cup attachment to round steel chains DIN 15237 Continuous handling equipment; Plate screws and cup washers for mounting components DIN 15261 Continuous handling equipment; Screw Conveyors Part 1 connection dimensions Part 2 screw blade DIN 15262 Continuous handling equipment; Screw conveyors for bulk; Principles of calculation DIN 15306 lifts - Lifts for Residential buildings - Dimensions, car dimensions, door dimensions
DIN 15309 lifts - Lifts for non-residential buildings and bed lifts - Dimensions, car dimensions, door dim DIN 15313 Lifts - clamps, shims for guide rails DIN 15315 cable lock, September 2006 Replaced by DIN EN 13411-7 DIN 15400 Lifting hooks for lifting appliances; Mechanical properties, materials, capacity and stress DIN 15401 Lifting hooks for lifting appliances; Simply hook Part 1 blanks Part 2 finished parts with threaded shank DIN 15402 Lifting hooks for lifting appliances; Double hook Part 1 blanks Part 2 finished parts with threaded shank DIN 15403 Lifting hooks for lifting appliances; Round thread DIN 15404 Lifting hooks for lifting appliances; Technical delivery conditions for hooks Part 1 Technical delivery conditions for forged hooks Part 2 Technical delivery conditions for laminated hooks DIN 15405 Lifting hooks for lifting appliances; monitoring in the use of hooks Part 1 hooks for lifting appliances; Monitoring the use of forged hooks Part 2 hooks for lifting appliances; monitoring in the use of laminated hooks DIN 15406 Lifting hooks for lifting appliances; scribing open the forged hook DIN 15407 hooks for cranes; Lamellar single hook for iron and steel ladles Part 1 compilation, main dimensions Part 2 items DIN 15408 Cranes; Zweirollige bottom blocks; Compilation DIN 15409 Cranes; Vierrollige bottom blocks; Compilation DIN 15410 Series lifting equipment; bottom blocks for electric hoists, einrollig and zweirollig; Compila DIN 15411 hoists, load hook suspensions for bottom blocks DIN 15412 Bottom blocks for lifting appliances; Trusses Part 1 blanks Part 2 finished parts DIN 15413 Bottom blocks for lifting appliances; Load hook nuts DIN 15414 Bottom blocks for lifting appliances; Securing pieces DIN 15417 Cranes; Under bottles; Sheaves of the form D with plain bearing DIN 15418 Cranes; Under bottles; Sheaves of the form C with ball bearings without inner sleeve Part 1 sheaves of the form C with ball bearings without inner sleeve Part 2 spacer sleeves for sheaves of the form C with ball bearings without inner sleeve Part 3 cap for sheaves of the form C with ball bearings without inner sleeve DIN 15421 Cranes; Under bottles; Sheaves of the form B with ball bearings and internal sleeve Part 1 of Form B pulleys with ball bearings and internal sleeve Part 2 inner sleeves and spacer sleeves for sheaves of the form B with ball bearings and internal sleev Part 3 cap for sheaves of the form B with ball bearings and internal sleeve DIN 15422 Cranes; Under bottles; Sheaves of the form A with cylindrical roller bearings and inner bus Part 1 sheaves of the form A with cylindrical roller bearings and inner bushings
Part 2 inner sleeves and spacer sleeves for sheaves of the form A with cylindrical roller bearings and i Part 3 cap for sheaves of the form A with cylindrical roller bearings and internal sleeve DIN 15428 hoists, lifting equipment, technical specifications DIN 15429 hoists, lifting equipment, monitoring in use DIN 15450 Cranes; Calculation of propeller shafts for driving run sets DIN 15451 Cranes; Drive shafts Part 1 connection dimensions Part 2 Flange DIN 15452 Cranes; Flanges for propeller shafts DIN 15453 Cranes; Drive shafts, instructions for installation, maintenance, transportation and storage DIN 15460 crane baskets for building materials; Safety requirements DIN 15551 safety film-to 35 mm (formerly DIN KIN 51) DIN 15560 projector for film, television, stage and photographic
Part 1 lighting devices (preferably headlight) for light bulbs from 0:25 kW to 20 kW and 0,125 kW met kW to; Optical Systems, Equipment Part 2 Fresnel (Fresnel)
Part 6 Graphical symbols for studio lighting, studio lights, stage lights and spotlights on the stage ligh plan template
Part 24 headlight and lighting fasteners, headlights base plate, pipe clip and cones, lights sleeve for p luminaires and lamps Part 25 connectors and adapters Part 26 attachment points for headlights Part 27 hand-operated stands, safety requirements and testing Part 38 Einschiebevorrichtungen, color wheels, color transparencies, color wheel frame, color film fram Part 40 color filters for stage and studio lights; Colorimetric Characteristics Part 45 support structures, for spotlights and components; Terms Part 46 Movable holding - construction and safety requirements Part 47 safety regulations for grid ceilings Part 100 Special networks and special connector at 250/400 V Part 104 Daylight headlight system up to 4000 W rated power and associated special connector DIN 15563 special sockets for film and television studios Part 3 single-pole sockets without special protective conductor for phase and neutral conductors, ~ 40 Part 4 Single-pole special sockets for the protective conductor DIN 15564 special plug for film and television studios Part 3 single-pole special plug without protective conductor for phase and neutral conductors, ~ 400/2 Part 4 Single-pole special plug for the protective conductor DIN 15905 sound engineering in theaters and multi-purpose halls Part 1 Requirements for own, co-productions and foreign productions Part 2 cables for sound engineering and video technology use; Requirements DIN 15905 Event Production-tone technique Part 5 Measures to preventDefault the risk of hearing loss of the audience by high sound exposure of sound systems
DIN DIN DIN DIN DIN DIN DIN DIN
15906 16085 16086 16160 16167 16168 16174 16175
Conference Venues Überdruckmeßgeräte with devices for electric alarm toxic Electric Pressure Gauges - Pressure transmitters, pressure gauges - terms and specification thermometer; Terms Machine glass thermometers with round case, size 160, just type; Dimensions and nomina Machine glass thermometers with round case, angle size 160, Type 90 °; Dimensions and n Machine glass thermometers with round case, size 250, just type; Dimensions and nomina Machine glass thermometers with round case, angle size 250, Type 90 °; Dimensions and n
DIN 16176 Machine glass thermometers with round case, angle size 250, Type 135 °; Dimensions and DIN 16181 Machine glass thermometers with V-shaped case, size 110, just type; Dimensions and nom
DIN 16182 Machine glass thermometers with V-shaped case, angle size 110, Type 90 °; Dimensions an DIN 16185 Machine glass thermometers with V-shaped case, size 150, just type; Dimensions and nom
DIN 16186 Machine glass thermometers with V-shaped case, angle size 150, Type 90 °; Dimensions an DIN 16189 Machine glass thermometers with V-shaped case, size 200, just type; Dimensions and nom DIN 16230 Measurement and control rules; recording medium in strip form for writing instruments
DIN 16235 Measurement and control rules; Electrical measuring instruments; Color cages for multi-sig locking positions DIN 16257 Nominal positions and position symbols for measuring instruments DIN 16261 cocks PN 16 with threaded port sleeves and collars-pin connection for pressure gauges DIN 16262 cocks PN 6 and PN 16 with Spannmuffen- and pin connection for pressure gauges DIN 16263 cocks PN 16 with Spannmuffen-, pin and test connection for pressure gauges DIN 16271 Shut-off valves PN 250 and PN 400 with test connection for pressure gauges (gauge) DIN 16281 holder for measuring instruments and fittings DIN 16282 Siphons for pressure gauges and accessories DIN 16283 clamping sleeves for pressure gauges and accessories DIN 16284 nipple connections for pressure gauges and accessories DIN 16286 screw plugs with connection thread G 1/2 B nach DIN EN 837-1 DIN 16287 sealing and protective caps for Prüfanschlusszapfen on fittings for pressure gauges DIN 16511 proofreading marks DIN 16514 printing technology; Terms for the high-pressure DIN 16518 classification headings by genus and categories DIN 16519 Testing of prints and printing inks Part 2 Preparation of standard pressure for optical testing DIN 16521 printing technology; Lines in the set of production; Mass DIN 16524 Testing of printing inks and printing technology - Resistance to various physical and chemi Part 5 autoclave retortability Part 6 Behaviour of labels for beverage bottles against hot alkaline solution, Laugendurchdringung an Part 7 Behaviour of labels for beverage bottles against hot alkaline solution, alkali resistance DIN 16526 inks for the printing technology - Identification of properties for sheet-fed offset printing in
DIN 16527 Printing Part 1 control box, control, control fire; Basic concepts Part 3 checkboxes; Application in pressure DIN 16528 printing technology; Terms for the low-pressure DIN 16529 printing technology; Terms for the planographic printing DIN 16536 Testing of printing inks and printing technology - color density measurement on printing Part 1 Definitions and measurement procedure DIN 16547 screen angles in color halftone reproduction DIN 16549 Graphic technology - Prepress Part 1 mark for correct image and additional information DIN 16551 Envelopes - Vocabulary DIN 16552 rulings for handwriting Part 1 General lineation DIN 16553 Printing and Graphic Technology; Passport system DIN 16555 office work place - Space for communication work places in office buildings - Requirements DIN 16557 Electronic data interchange for administration, commerce and transport (EDIFACT) Part 3 General Introduction for uniform message types (UNSMs)
Part 4 Rules for Award of UN / EDIFACT transfer files using the eXtensible Markup Language (XML) usin Definitions (DTDs)
Part 5 rules to generate XML schema files (XSD) from EDI (FACT) -Anwendungsbeschreibungen (ISO / T DIN 16716 pressing, molding - Guide bushes made of steel DIN 16726 Plastic Sheeting - Examinations DIN 16740 Textile glass; Textile glass fabrics for electrical purposes, technical delivery DIN 16741 Textile glass; Textile glass fabric tapes with fixed selvedges for electrical purposes, technic DIN 16742 plastic Molding - Tolerances and acceptance conditions DIN 16747 roughness of forming Surfaces of pressing tools and injection molds for plastic molding DIN 16759 pressing, molding - Centering DIN 16760 Pressed, for molding Part 1 Edited undrilled plates DIN 16761 pressing, molding - Guide pillars DIN 16764 Tool Specification Sheet Part 3 Hot Runner Systems and Hot Halves DIN 16765 pressing, molding - Electrical connections for hot runner molds and mold heating DIN 16766 for molding - temperature control for liquid media Part 1 nipple and installation spaces, the tool side DIN 16769 pressing and injection molds - Components for gating systems - Definitions DIN 16780 plastic molding materials; Thermoplastic molding compounds of polymer Mixtures Part 1 Classification and designation Part 2 Preparation of test specimens and determination of properties DIN 16781 plastic molding materials; polyoxymethylene (POM) molding and extrusion materials Part 2 Preparation of test specimens and determination of properties
DIN 16782 plastic molding materials; Polytetrafluoroethylene (PTFE) molding and extrusion materials Part 1 Classification and designation Part 2 Preparation of test specimens and determination of properties DIN 16830 Window profiles of high impact resistant polyvinyl chloride (PVC-HI) Test methods Part 1 Part 2 white; Requirements Part 3 profiles coated with colored Surfaces; Requirements Part 4 profiles with coated, colored Surfaces; Test methods DIN 16831 Pipes and Pipe Fittings for pressure pipes of polybutene (PB) Part 1 angle of injection for socket welding, Dimensions Part 2 tees from molded for socket welding Part 3 sleeves and caps, injection molding for socket welding, Dimensions Part 4 Reducers injection for socket welding, Dimensions Part 5 General quality requirements and testing Part 6 electrofusion fittings, Dimensions Part 7 bushings, flanges, gaskets in injection molding for socket welding, Dimensions
DIN 16832 pipe joints and fittings for pressure piping systems made of chlorinated polyvinyl chloride ( Part 1 Dimensions Part 2 General quality requirements and testing
DIN 16833 Pipes made of Polyethylene of raised temperature resistance (PE-RT) - PE-RT Type I and Typ quality requirements and testing
DIN 16834 Pipes made of Polyethylene of raised temperature resistance (PE-RT) - PE-RT Type I and Typ Dimensions DIN 16836 Multilayer Pipes - polyolefin-aluminum composite pipes - General requirements and tests DIN 16837 multilayer pipes - multi-layer plastic composite pipes - General requirements and tests
DIN 16838 Thermoplastics materials for fittings - Polyphenylene (PPSU) - General quality requirements German and English
DIN 16839 Thermoplastics materials for fittings - Polysulfone (PSU) - General quality requirements and German and English
DIN 16840 Thermoplastics materials for fittings - Polyvinylidene fluoride (PVDF) - General quality requ testing; Text in German and English
DIN 16841 Plastics piping systems - testing of pipes and pipe components - Determination of creep m bending test
DIN 16842 pipes made of polyethylene (PE) - HDPE for pressure applications - General quality requirem and tests; Text in German and English
DIN 16867 pipes, fittings and joints of glass-reinforced polyester resin (UP-GF) for use in chemical pipe delivery conditions DIN 16868 tubes made of glass fiber reinforced polyester resin (UP-GF) Part 1 Wrapped filled; Mass Part 2 Wrapped filled; General quality requirements and testing DIN 16869 tubes made of glass fiber reinforced polyester resin (UP-GF), centrifuged, filled Part 1 Dimensions
Part 2 General quality requirements and testing
DIN 16872 Pipes and Pipe Fittings for pipes made ??of thermo plastics; Flanges made ??of glass fiber r resin (UP-GF); Mass
DIN 16873 Pipes and fittings made of unplasticized polyvinyl chloride (PVC-U) for cable ducting - Dime delivery conditions
DIN 16874 Pipes made of high density polyethylene (HDPE) for buried telecommunication - Dimension delivery
DIN 16875 Pipes and fittings made of unplasticized polyvinyl chloride (PVC-U) for buried ducting - Dim technical delivery
DIN 16876 Pipes and fittings made of high density polyethylene (HDPE) for buried cable ducting - Dim technical delivery DIN 16878 Pipes and fittings of polypropylene (PP) for buried cable ducting - Dimensions and technica DIN 16887 testing of pipes made ??of thermoplastic material; Determination of the long-term hydrost DIN 16889 Determination of the chemical resistance factor for thermoplastic plastics pipes Part 1 polyolefin pipes DIN 16892 Pipes of crosslinked polyethylene high density (PE-X) - General quality requirements and te DIN 16893 Pipes of crosslinked high density polyethylene (PE-X) - Dimensions DIN 16894 Pipes of crosslinked medium density polyethylene (PE-MDX) - General quality requirements DIN 16895 Pipes of crosslinked medium density polyethylene (PE-MDX) - Dimensions
DIN 16901 plastic Molding, Tolerance and acceptance conditions for linear dimensions, November 200 without replacement DIN 16903 threaded inserts for plastic Molding (and die-cast) Part 1 open Part 2 is closed, with disc Part 3 closed Part 4 heavy duty DIN 16906 Testing of plastic sheets and plastic films - sample and specimen - collection, pretreatment DIN 16922 produced using plastics flexible web-shaped sheet material; Technological classification DIN 16928 pipes made ??of thermoplastic materials, Pipe fittings, piping components, installation, Ge
DIN 16940 Plastics - Extruded tubes made of plasticized polyvinyl chloride (PVC-P) - Tolerances on dim tolerances DIN 16941 Extruded profiles made of thermoplastic plastics - General tolerances on dimensions, shap DIN 16945 Resins, reagents and reaction resins; Test methods DIN 16946 reactive resin molded materials, casting resin molding Test methods Part 1 Part 2 types DIN 16960 welding of thermoplastic plastics Part 1 Principles
DIN 16964 tubes made ??of glass fiber reinforced polyester resin (UP-GF), wound; General quality req testing DIN 16965 tubes made of glass fiber reinforced polyester resin (UP-GF) wound, Part 1 tube type A; Mass Part 2 pipe type B; Mass
Part 4 pipe type D; Mass Part 5 tube type E; Mass DIN 16966 fittings and joints made of glass fiber reinforced polyester resin (UP-GF) Part 1 Fittings, General quality requirements and testing Part 2 sheets; Mass Part 4 tees, stub; Mass Part 5 reducers; Mass Part 6 bushings, flanges, gaskets; Mass Part 7 bushings, flanges, flange and laminated joints; General quality requirements and testing Part 8 laminated joints; Mass DIN 17007 standard numbers Part 4 systematics of the main groups 2 and 3: non-ferrous metals DIN 17014 heat treatment ( hardening ) Of metals Supplement 2 Foreign language translation of technical terms, February 2008 WITHDRAWN without re Part 3 short notice for heat treatments DIN 17022 Heat treatment of ferrous materials - Methods of heat treatment Part 1 Hardening, Austempering, annealing and tempering of components Part 2 hardening and tempering of tools Part 3 hardening Part 4 nitriding and Nitrocarburizing Part 5 Surface hardening DIN 17052 Heat treatment furnaces Part 1 Requirements for temperature uniformity
DIN 17103 forgings made of weldable fine grain structural steels - Technical delivery conditions, Oct. 1 DIN EN 10222-1 DIN 17175 Seamless tubes of heat-resistant steels, technical specifications, Replaced by DIN EN 1021 DIN 17221 Hot rolled steels for quenched and tempered springs; April 2003 Replaced by DIN EN 1008 DIN 17222 Cold-rolled steel strip for springs, May 2000 TO BE REPLACED DIN EN 10132-1 and DIN EN DIN 17223 Round spring steel wire Part 1 Patented cold drawn spring wire of non alloy steels; December 2001 Replaced by DIN EN 10270
Part 2 oil hardened and tempered spring steel wire alloy and alloy steels; December 2001 Replaced by DIN 17224 spring wire and spring strip of stainless steels; February, 2003 Replaced by EN 10151 and
DIN 17280 Cryogenic steels - Technical delivery conditions for sheet, strip, wide flats, mold steel, stee December 1999 Replaced by DIN EN 10028, DIN EN 10223 and DIN EN 10269 DIN 17410 permanent magnet materials February 2001 Replaced by DIN IEC 60404-8-1 DIN 17440 Stainless steels, September 2005 Replaced by DIN EN 10088-3
DIN 17455 Welded circular tubes of stainless steels for general requirements, December 2002 Replace 2 and DIN EN 10312
DIN 17456 Seamless circular tubes of stainless steels in general for requirements, February 2006 Rep 10297-2
DIN 17457 Welded circular tubes of austenitic stainless steels with special requirements, March, 2005 10217-7 DIN 17471 resistance materials DIN 17640 Part 1 lead alloys for general use DIN 17740 Nickel in semis - composition DIN 17741 Low-alloyed nickel alloys - Composition DIN 17742 Wrought nickel alloys with chromium - composition DIN 17743 Wrought nickel alloys with copper - composition DIN 17744 Wrought nickel alloys with molybdenum and chromium - composition DIN 17745 Wrought alloys of nickel and iron - composition DIN 17750 strips and sheets of nickel and nickel alloys - Properties DIN 17751 Pipes made of nickel and nickel alloys - Properties DIN 17752 rods of nickel and nickel alloy wrought - Features DIN 17850 titanium; Chemical composition DIN 17851 titanium alloys; Chemical composition DIN 17860 strips and sheets of titanium and titanium alloys - Technical specification DIN 17861 Seamless circular tubes of titanium and titanium alloys; Technical delivery conditions DIN 17862 Titanium and titanium alloys of bars - Technical specification DIN 17863 wires made of titanium
DIN 17864 forgings made of titanium and titanium alloys wrought forgings (hammer and drop forging specifications DIN 17865 castings made ??from titanium and titanium alloys, investment casting, Kompaktguß DIN 17866 Welded circular tubes of titanium and titanium alloys; Technical delivery conditions DIN 17869 material properties of titanium and titanium alloys; Additional Information DIN 18000-18298 [ Edit ] DIN 18000 Modular order in Construction
DIN 18004 applications of building products in structures - Test methods for aggregates nach DIN V 20 20000-104 (pre-standard) DIN 18005 Noise abatement in town Chapter 1 Basics and Important Notes Part 1, Supplement 1, method of calculation; Acoustic orientation values ??forurban planning Part 2 noise maps, Cards representation of noise emissions DIN 18007 Demolition - Definitions, Processes, applications DIN 18008 Glass in building - Design and construction rules Part 1 Definitions and General Principles (Draft) Part 2 line-mounted glazing (Draft) DIN 18011 shelves, spacing and movement areas in housing, in January 1991 WITHDRAWN without re DIN 18012 home port facilities in buildings - Spatial and space requirements - Design principles DIN 18013 niches for meter panels (electricity meters) DIN 18014 Foundation Earth DIN 18015 Electrical installations in residential buildings
Part 1 Planning Basics Part 2 of the nature and extent of minimum equipment Part 3 Wiring and disposition of resources DIN 18017 ventilation of bathrooms and toilets without outside windows Part 1 individual duct systems without fans Part 3 with fan DIN 18022 kitchens, bathrooms and toilets in housing, planning principles, WITHDRAWN without repla DIN 18024 barrier-free building Part 1 streets, squares, roads, public transport, recreation areas and playgrounds; Planning Basics Part 2 Publicly accessible buildings and workplaces, design principles; 2010 Replaced by DIN 18040-1 DIN 18025 barrier-free apartments Part 1 homes for wheelchair users; Planning Basics Part 2 Planning Basics DIN 18032 Sport halls - Halls for gymnastics, games and multi-purpose use Part 1 Principles for planning Part 2 Sports Flooring, Requirements, tests (pre-standard) Part 3 examination of the impact resistance Part 4 double-layered curtains Part 5 Telescopic tribunes Part 6 Structural measures for installation and anchoring of sports equipment DIN 18034 Playgrounds and outdoor play areas - Requirements and information on planning and oper DIN 18035 Sports Facilities Part 1 outdoor facilities for games and athletics, planning and Dimensions Irrigation Part 2 Part 3 drainage Part 4 lawns Part 5 threshing floor Surfaces Part 6 plastic Surfaces Part 7 Synthetic turf areas Part 8 athletics facilities DIN 18040 accessible buildings - Design principles Part 1 Publicly accessible buildings Part 2 apartments DIN 18041 Acoustic quality in small to medium-sized rooms DIN 18055 Windows; joint permeability, water tightness and mechanical stress; Requirements and tes DIN 18057 Concrete windows - Dimensioning, requirements, testing DIN 18065 building stairs - Definitions, rules, key dimensions DIN 18090 Lift - elevator shaft and turning -Falttüren for lift wells with walls of fire resistance class F 9 DIN 18091 elevators; Shaft-sliding doors for lift wells with walls of fire resistance class F 90 DIN 18092 elevators, vertical sliding doors for service lifts in lift shafts with walls of fire resistance clas
DIN 18093 Fire barriers; installation of fire doors in solid walls of masonry or concrete; Of anchors, anc installation DIN 18095 smoke protection doors Part 1 Definitions and requirements Part 2 type testing for durability and impermeability Part 3 Application of test results DIN 18100 Doors, Wall openings for doors; Dimensions nach DIN 4172 DIN 18104 Mechanical safety devices - Burglar aftermarket products for windows and doors DIN 18111 door frames - steel frames Part 1 standard frames for rebated doors in masonry walls Part 2 standard frames for rebated doors in stud frame walls Part 3 special frames for rebated and rebated door leaves Part 4 installation of steel frames DIN 18121 investigation and testing - Water content Part 1 by determined by oven drying Part 2 Determination by rapid methods DIN 18122 Soil, investigation and testing - state boundaries (consistency limits) Part 1 Determination of flow and plastic limit Part 2 Determination of shrinkage limit DIN 18123 Soil, investigation and testing - Determination of particle size distribution
DIN 18124 Soil, investigation and testing - Determination of density - Capillary, wide mouth pycnomet DIN 18125 Soil, investigation and testing - Determination of density of soil Part 1 laboratory tests Part 2 field trials
DIN 18126 Soil, investigation and testing - Determination of density of non-cohesive soils for maximum compactness DIN 18127 Soil, investigation and testing - Proctor DIN 18128 Soil - investigation and testing - Determination of loss on ignition DIN 18129 Soil, investigation and testing - Determination of lime content DIN 18130 Soil - investigation and testing; Determination of water permeability Part 1 laboratory tests Part 2 field trials DIN 18132 Soil, testing procedures and testing equipment - Determination of water absorption DIN 18134 Soil - experimental and testing equipment - plate load test DIN 18135 Soil - investigation and testing - oedometer attempt DIN 18136 Soil - investigation and testing - Unconfined compression test DIN 18137 Soil, investigation and testing - Determination of shear strength Part 1 Concepts and general testing conditions Part 2 triaxial test Part 3 Direct shear test Part 4 wing shear tests
DIN 18150 Materials and components for domestic chimneys, fittings made ??of lightweight concrete, Part 1 requirements Part 2 examination and monitoring DIN 18156 materials for ceramic tiling by the thin-bed method DIN 18157 Installation of ceramic tiling by the thin-bed method Part 1 hydraulic hardening thin-bed mortar Part 2 dispersion adhesives Part 3 Epoxy resin DIN 18158 ground clinker tiles
DIN 18159 foamed plastics as in-situ in the construction industry; Urea-formaldehyde resin in-situ for Part 2 application, properties, execution, testing, DIN 18180 Gypsum plasterboards - Types and Requirements DIN 18181 plasterboard in buildings - processing DIN 18182 Accessories for use with gypsum boards Part 1 profiles made of sheet steel Part 2 screws drywall, staples and nails DIN 18183 partitions and wall linings made of gypsum boards with metal substructures Part 1 planking with plasterboard DIN 18190 waterproofing membranes for waterproofing of buildings; Geomembrane with metal strip i Part 4, by definition, designation, requirements
DIN 18192 Bonded polyester fleece used as inlay for bitumen and polymer in bitumen sheets, definitio requirements, testing DIN 18195 Structure_sealing Part 1 Principles, definitions, attribution of waterproofing types Part 2 substances Part 3 requirements on the ground and working of materials Part 4 waterproofing against ground moisture and non-accumulating seepage water under floor slabs and execution Part 5-proofing against non-pressing water on floors and in wet areas; Design and construction Part 6 seals against pressing from the outside water and seepage water; Design and construction Part 7 seals against pressing water from the inside; Design and construction Part 8 seals on joints Part 9 Penetrations, transitions, connections and terminations Part 10 protective layers and protective measures Part 100 Proposed amendment to the DIN 18195 Part 1 to 6 (Draft) Part 101 Proposed amendment to the standard DIN 18195-2 to 18195-5 DIN (Draft) DIN 18196 Earthworks and foundations - Soil classification for civil engineering purposes
DIN 18200 Verification of conformity for building products - Factory production control, external monit certification of products DIN 18201 Tolerances in building construction, concepts, principles, application, testing
DIN 18202 Tolerances in building construction - Buildings DIN 18203 Tolerances in building construction Part 1 Prefabricated parts made of concrete, reinforced concrete and prestressed concrete Part 2 Pre-fabricated steel parts Part 3 components made of wood and wood-based materials DIN 18205 MRP in Construction
DIN 18215 form panels of wood, concrete and reinforced concrete structures for; standard dimensions thickness 21 mm DIN 18216 form anchor for concrete formwork; Requirements, testing, use DIN 18217 Concrete Surfaces and form worksurface DIN 18218 fresh concrete pressure on vertical formwork DIN 18225 Industrial, traffic ways in industrial DIN 18230 Structural fire protection in industrial Part 1 analytically required fire resistance Part 2 Determination of the burning behavior of materials in storage arrangement - Combustion factor Part 3 values ??calculated is DIN 18232 Smoke and heat control systems (uA RWA ) Part 1 terms, task Part 2 Natural smoke extraction system (NRA), design, performance and installation Part 4 heat extraction (WA); Test methods Part 5 Mechanical smoke extraction system (MRA); Requirements, design Part 6 Requirements for individual components and qualification records (pre-standard) Part 7 heat extraction from meltable materials - assessment procedures and Installation (draft) DIN 18234 Structural fire protection in industrial DIN 18250 Locks - Locks for fire and smoke protection doors DIN 18251 Locks - Mortise Part 1 Mortise locks for rebated doors Part 2 mortice lock for metal frame doors Part 3 Mortise as multi-point lock DIN 18252 profile cylinder for door locks DIN 18257 Building hardware - Security plates - Definitions, measurements, requirements, marking DIN 18262 Adjustable anti-supporting spring tape for fire doors DIN 18263 Building hardware - Door closer with hydraulic damping Part 1 Top door closer with crank drive and spiral spring Part 4 door closers with automatic opening (vane type) DIN 18264 Building hardware; Hinges with spring DIN 18265 Building hardware; Swing door hinges with spring DIN 18267 Window handles - Lockable, sealable and lockable window handles DIN 18268 Building hardware; Hinges; band reference line DIN 18272 Fire barriers; Hinges for fire doors; Spring band-structure and band
DIN 18273 Building hardware - door handle sets for fire doors and smoke control doors - Definitions, m requirements and tests
DIN German construction contract procedures 18299-18459 - Part C: General technical specifications contracts (ATV) [ edit ] DIN 18299 General rules for construction work of any kind DIN 18300 Earthwork DIN 18301 Drilling DIN 18302 on the Strengthening of holes (formerly: Well construction work) DIN 18303 Verbauarbeiten DIN 18304 ramming, vibrating and pressing jobs (formerly: Pile driving) DIN 18305 Groundwater lowering DIN 18306 Underground drainage DIN 18307 pressure pipework outside buildings (formerly pressure pipework in the ground) DIN 18308 drainage works DIN 18309 grouting DIN 18310 Security works at water, dikes and coastal dunes WITHDRAWN, DIN 18311 dredging DIN 18312 underground construction work DIN 18313 diaphragm walls with supportive fluids DIN 18314 shotcrete DIN 18315 Road construction - top layers without binders DIN 18316 Road construction - Track with hydraulic binders DIN 18317 Road construction - asphalt surfacings DIN 18318 Road construction - plaster and slab pavements, and surrounds DIN 18319 Pipe Jacking Works DIN 18320 Landscaping works DIN 18321 Jet grouting works DIN 18322 cable laying works DIN 18323 ordnance clearance work DIN 18325 railway works DIN 18326 renovation of drainage channels DIN 18330 brickwork DIN 18331 Concrete and reinforced concrete DIN 18332 Natural stonework DIN 18333 Betonwerksteinarbeiten DIN 18334 Carpentry and timber construction DIN 18335 steelwork DIN 18336 Waterproofing DIN 18338 Roofing and roof sealing works DIN 18339 Plumbing DIN 18340 Trockenbauarbeiten DIN 18345 thermal insulation composite systems DIN 18349 Repair work on concrete
DIN 18350 plaster and stucco DIN 18351 rainscreen facades DIN 18352 Tile laying works DIN 18353 Estricharbeiten DIN 18354 Gußasphaltarbeiten DIN 18355 joinery DIN 18356 Parkettarbeiten DIN 18357 fitting work DIN 18358 fitting shutters DIN 18360 Metal construction work DIN 18361 glazing work DIN 18363 painting and decorating work - Coatings DIN 18364 Corrosion protection of steel and aluminum DIN 18365 covering work DIN 18366 wallpapering DIN 18367 wood blocks DIN 18379 Air conditioning systems DIN 18380 Heating systems and central water heating system DIN 18381 Gas, water and drainage systems inside buildings DIN 18382 low and medium voltage systems with nominal Voltages up to 36 kV DIN 18384 lightning protection systems DIN 18385 conveyors, elevators, escalators and moving walkways DIN 18386 Building Automation DIN 18421 Insulation works on technical installations DIN 18451 Scaffolding work DIN 18459 demolition and dismantling DIN 18500-18999 [ Edit ] DIN 18500 cast stone DIN 18501 Concrete paving blocks DIN 18502 paving stones stone DIN 18503 pavers DIN 18515 External wall cladding Part 1 Tiles fixed with mortar - Principles for design and construction Part 2 Anmauerung on footprints - Principles for design and construction DIN 18516 External wall cladding ventilated, Part 1 requirements, principles of testing Part 3 natural stone, requirements, LAYOUT Part 4 toughened safety glass - requirements, design, testing, Part 5 concrete blocks - Requirements, Design DIN 18530 Massive ceiling constructions for roofs; Planning and execution DIN 18531 roof waterproofing - Waterproofing of roofs unused
Part 1 Definitions, requirements, design principles Part 2 substances Part 3 Design, handling of materials, execution of sealings Part 4 Maintenance DIN 18540 Sealing of outside wall joints in building using joint sealants DIN 18541 water stops made of thermoplastic material for sealing joints in situ concrete Part 1 Definitions, shapes, dimensions, marking Part 2 requirements for materials, testing and monitoring
DIN 18542 Sealing of outside wall joints with impregnated joint sealing tapes made of cellular plastics sealing tapes - Requirements and testing DIN 18545 Sealing glazing with sealants Part 1 Requirements for Glasfalze Part 2 Sealants, designation, requirements, testing Part 3 glazing systems DIN 18550 plaster and plaster systems - design (pre-standard) DIN 18551 shotcrete - National rules for series DIN EN 14487 and rules for the design of sprayed conc DIN 18554 Testing of masonry Part 1 Determination of compressive strength and modulus of elasticity DIN 18555 Testing of mortars Containing mineral binders Part 3 hardened mortar; Determination of flexural strength, compressive strength and density
Part 4 hardened mortar; Determination of the longitudinal and transverse strain and deformation char masonry mortars in the static compression test Part 6 hardened mortar; Determining the adhesive strength Part 7 fresh mortar; Determination of the water retention capacity after the filter plate method Part 9 hardened mortar; Determination of compressive strength joints DIN 18558 plasters; Definitions, requirements, design DIN 18560 Screeds in the construction industry Part 1: General requirements, testing and implementation Part 2 screeds and screeds heated on insulation (floating screeds) Part 3 bonded screeds Part 4 screeds on separating layer Part 7 Heavy duty screeds (industrial screeds)
DIN 18581 Instructions for factory production control for CE Marking (AoC 2+) masonry mortars after q examination
DIN V 18599 Energy performance of buildings - Calculation of the net, final and primary energy dema cooling, ventilation, lighting and drinking water (pre-standard on the basis of the 2002/91 / EC and Ee Energy Saving Ord Part 1 General balance method, concepts, zoning and evaluation of energy Part 2 energy demand for heating and cooling of building zones Part 3 Effective energy requirements for air conditioning energy Part 4 useful and final energy demand for lighting Part 5 Final energy demand of heating systems
Part Part Part Part Part
6 Final energy demand of residential ventilation systems and air heating systems for housing 7 Final energy demand of air-handling and air conditioning systems for residential 8 useful and final energy demand of domestic hot water systems 9 final and primary energy demand of combined heat and power plants 10 Boundary conditions of use, climatic data
Part V to DIN 100 DIN V 18599-1 changes to 18599-10 (Shall be included in a new version of DIN 1859 of 2011 and there are only Partially part of the energy performance of buildings nach EnEV ) DIN 18650 Building hardware - Automatic door systems Part 1 Product Requirements and test methods Part 2 security of automatic door systems DIN 18702 characters of Surveying cracks, large scale maps and plans DIN 18710 Engineering Surveying Part 1: General requirements Part 2 uptake Part 3 Stakeout Part 4 Monitoring DIN 18723 Field procedures for testing geodetic and surveying instruments accuracy Part 1 General Part 2 levels Part 3 Theodolites Part 4 optical distance meter Part 5 Lotinstrumente Part 6 Electro-optical distance meter for near Part 7 surveying gyroscope Part 8 rotary laser DIN 18799 Fixed ladders for construction works Part 1 Ladders with two uprights, safety requirements and testing Part 2 ladders with a central stringer, safety requirements and testing DIN 18800 steel construction Part 1 Design and construction Part 2 cases stability, buckling of members and frames Part 3 cases stability, plate buckling Stability Part 4 cases, shell buckling Part 5 Composite structures of steel and concrete - Design and construction Part 7 execution and qualification DIN 18801 steel construction, design, construction, manufacturing DIN 18807 Trapezoidal sheeting in building Part 1: General requirements and determination of load bearing capacity by calculation Part 3 steel trapezoidal profiles, stress analysis and structural design Part 9 aluminum trapezoidal sheeting and Their connections; Application and design
DIN 18820 Laminates of textile glass-reinforced polyester and Unsaturated phenacrylic resins for struc UP, GF-PHA)
Part 1 Design, preparation and properties Part 2 Physical characteristics of the rule laminates Part 3 protections for the base laminate Part 4 testing and quality control DIN 18851 Large Cooking Appliances - Ovens - Requirements and test methods DIN 18852 catering equipment - Brat and grills - Requirements and testing
DIN 18854 catering equipment - roasting and baking ovens floors, pastry ovens (Patisserie) - Requirem DIN 18855 catering equipment Part 1 Double cooking kettle and electric boiler with pressure-free cooking space - Requirements and t Part 2 pressure cooking kettles, requirements and testing DIN 18856 catering equipment - Fryers - Requirements and testing DIN 18857 catering equipment Part 1 Tilting pans; Requirements and testing Part 2 frying pans status, requirements and testing Part 3 tilt Druckgarpfannen, requirements and testing Part 4 stand-Druckgarpfannen, requirements and testing DIN 18858 catering equipment - Salamander and Gyros Grills - Requirements and testing DIN 18860 Equipment for commercial kitchens - Working tables Part 1 Openwork tables; Requirements and testing Part 2 desks with Schrankunterbauten; Requirements and testing DIN 18861 commercial kitchens - Dishwashing facilities and sinks Part 1 Sink; Requirements and testing Part 2 sinks; Requirements and testing Part 3 wash hand basin, requirements and testing Part 4 Sinks, requirements and testing Part 5 handwashing Ausgussbeckenkombination, requirements and testing DIN 18862 catering equipment - Machines for roasting and grilling; Requirements and testing Part 1 Kurzzeitbratstücke Part 2 Langzeitbratstücke
DIN 18863 catering equipment - Machines and apparatus for cooking and preparation under steam pr Requirements and testing DIN 18864 Equipment for commercial kitchens - Thermal container for food transport DIN 18865 catering equipment - distribution equipment Part 1 dimensions, requirements, testing Part 2 hot issues Part 3 output tables (Neutral devices) Part 4 heated or unheated structures Part 5 Tray slides Part 6 installation stackers (heated or unheated) Part 7 Cold output devices (refrigerators) Part 8 bodies cooled,
Part 9 cabinet interiors in standard and hygienic design DIN 18870 catering equipment - Limits for flue gas losses DIN 18871 commercial kitchens - Thermal equipment Part 1 dish warming cabinets - Requirements and test methods Part 2 Heated pool - Requirements and testing Part 3 water baths - Requirements and testing Part 4 pasta cookers, requirements and testing DIN 18872 commercial kitchens - Refrigeration technology equipment Part 1 refrigerated and frozen tables; Requirements and testing Part 2 cooling troughs; Requirements and testing Part 3 refrigerated display cases in the output area; Requirements and testing Part 4 refrigerators and freezers; Requirements and testing Part 5 Blast chillers and blast freezers; Requirements and testing DIN 18873 Methods for the determination of the energy consumption of large kitchen appliances Part 1 combi steamer Part 2 Commercial hot beverage maker Part 3 fryers Part 4 hot air circulating ovens Part 5 Tilting pans and skillets Stand Part 6 tilt Druckgarpfannen and stand-Druckgarpfannen Part 7 deck ovens Part 8 regeneration Part 9 cooking zones Part 10 Ice Makers
DIN 18889 Memory coal-water heater, without pressure for 1 atm test pressure; Concepts, constructio performance, testing DIN 18890 for solid fuel burning stoves Part 10 Low-smoke combustion
DIN 18893 Space heating capacity of individual fireplaces; approximation method for the determinatio size DIN 18894 fireplaces for solid fuels - Pellet Stoves - Requirements, testing and marking DIN 18896 fireplaces for solid fuels - Technical rules for the installation requirements for a user manua DIN 18897 fireplaces for solid fuels - Room sealed furnaces Part 1 space heaters DIN 18900 wooden pole design; Design and construction DIN 18902 stoneware pieces for the house construction, bowls, plates, trays, Dimensions, requiremen DIN DIN DIN DIN
18908 18915 18916 18917
floors for stables; Slatted floors of precast reinforced concrete or wood; Dimensions, loads, Vegetation technology in landscaping - floor work Vegetation technology in landscaping - plants and planting Vegetation technology in landscaping - lawn and seeding
DIN 18918 Vegetation technology in landscaping - Biological methods - Stabilization by seeding and p of living and non living materials and components, combined construction methods DIN 18919 Vegetation technology in landscaping - development and maintenance maintenance of gre
DIN 18920 Vegetation technology in landscaping - Protection of trees, plantations and vegetation area construction DIN 18951 Earth Building Regulations 1971 WITHDRAWN without replacement DIN 18960 user cost in building construction DIN 19000-19999 [ Edit ] DIN 19001 accessory shoe for mounting camera accessories; Connecting dimensions DIN 19002 camera lenses Part 1 Connection dimensions for plug-and schraubares Accessories DIN 19003 connector flash, flash cable, plug nipple, Part 1 connection dimensions, requirements DIN 19004 Phototechnik; Cable release, cable release sleeve, connecting dimensions DIN 19010 A photoelectric exposure meter Part 1 scales, calibration Part 2 Automatic exposure control in photographic cameras Part 3 Lightning exposure meters DIN 19011 flashlight sources Part 1 Determination of GN and Performance Part 2 electronic flash with automatic exposure control Part 3 ratios for the spectral distribution DIN 19012 flash bulbs, flash lamp assemblies using dedicated reflectors; Photometric data
DIN 19015 time measurement of central locking; term, exposure times, measuring arrangements; Syn
DIN 19016 time measurement of focal plane shutters; term, exposure times, measuring arrangements contacts DIN 19017 Exposure Value; Concepts and reference point, exposure correction DIN 19021 Rating of silent image throwers throw light bulbs Part 2 Temperature measurements on slide projectors Part 3 temperature measurement at work projectors DIN 19030 Filter for Recording, copying and reproduction purposes; Printing filters Part 3 intake filter, filter names Part 4 printing filters; Determining the filter values Part 5 printing filters; Remove scales on color copiers DIN 19045 projection of silent and motion picture Part 1 projection and viewing conditions for all kind of Projection Part 2 Prefabricated Screens
Part 3 minimum dimensions for the smallest elements, line widths, font and glyph size in original tem Part 4 reflection and transmission properties of screens; Distinguishing sizes, screen type, measureme Part 5 Teaching and home projection for resting and motion picture Safety requirements for the made-
Part 6 of teaching and home projection for resting and motion images, symbols and Infosign Part 7 measurement method for deterministic mining the imaging properties of slide projectors Part 8 light measurements When Projecting images with a projector and a separate screen Part 9 light measurements When Projecting images with projection units DIN 19046 projection technology, stage and theater projection for standing, walking and jogging imag Part 1 General Part 2 oblique projection Onto flat screens, projection devices and overhead presentations Part 2, Supplement 1 oblique projection Onto flat screens, working documents for practical use Part 2, Supplement 2 DIN-alignment slide A to align the image Stage, Size 13 × 13 Part 2 Supplement 3 DIN-alignment slide A to align the image Stage, Size 18 × 18 Part 2 Supplement 4 DIN-alignment slide B to apply the projection Part 3 stage lighting and projection of the stage statements DIN 19051 test templates for the micrograph Part 20 test shots made to establish the conditions for drawing movie Part 21 test shots made to establish the conditions for the filming of records, literature and newspape DIN 19052 microfilm technology; Drawing movie Part 1 microfilm 35 mm, dimensions Part 2 microfilm 35 mm, recording techniques Part 3 microfilm 35 mm, reduction and enlargement Part 4 Shooting in part on microfilm 35 mm Part 6 microfilm 35 mm; Minimum requirements for enlargements DIN 19053 microfilm card for film 35 mm DIN 19057 microfilm technology; Filming of newspapers, shot on 35 mm film DIN 19058 color microfilm - recording technology, producing original line art and halftone templates r DIN 19059 microfilm; Symbols for microfilming Part 2 Application and Overview Part 2, Supplement 1 templates for practical application DIN 19078 microfilm technology; Microfilm readers Part 1 Requirements for trans mitted light microfilm readers Part 4 Minimum information datasheets DIN 19204 Durchflußmeßtechnik, display areas, due to the divisions and numbering of the scales for fl DIN 19207 Measurement of fluid flow restrictor devices - Threaded connection and Accessories DIN 19211 Measurement of fluid flow restrictor devices - Compensation vessels DIN 19214 Flow Measurement - Primary Flow
Part 1 orifice plates with flange taps, nominal diameter 50 to 500, nominal pressure 10 to 100 - seal s
Part 2 orifice plates with flange taps, nominal diameter 10 to 400, nominal pressure 10 to 100 - and se (Withdrawn) Part 3 orifice plates with flange taps, nominal diameter 10 to 400, nominal pressure 64-400 - seal lens Part 4 orifice plates with flange taps; Measured sections, nominal diameter 10 to 200 (for + ückgezog
Part 5 throttle device with Meßflanschen; Length of the extraction socket and mounting dimensions fo of the space required (Withdrawn)
DIN 19216 Durchflußmeßtechnik - mounting arrangements for flow measurement using the differentia
DIN 19217 measuring systems for liquids other than water - Definitions, requirements and testing (OIM DIN 19221 regulation and control technology - Symbols DIN 19222 I & C - Definitions (currently draft standard DIN V 19222) DIN 19223 Control technology - Rules for the designation of measuring instruments DIN 19225 naming and classification of regulators (2009 Replaced by DIN IEC 60050-351) DIN 19226 Control Engineering and Control Engineering (2009 Replaced by DIN IEC 60050-351) DIN 19227 control, Graphical symbols and Identifying letters for process control Part 1 Presentation of tasks Part 2 illustrate details DIN 19235 Measurement and control rules, reporting of operating conditions DIN 19237 Control technology (terms) DIN 19242 Measurement and control rules; Performance Test of Time Computer Systems; Time measu Part 1 testMethod Part 2 test function: Multiplication Part 3 test function: Conditional jump Part 4 Test function: sine calculation Part 5 test function: Matrix inversion Part 6 test function: find a bit pattern Part 7 test function: interrupt treatment with program start Part 8 test function: I / O-operation on peripheral memory (Random Access Memory) Part 9 Test Function: Digital input and output Part 10 test function: Dialogue on the terminal Part 11 test function: synchronization with message traffic between two tasks Part 12 test function block by reading and writing to files (Random Access Memory) Part 13 test function: data transmission with interference-free transmission path Part 14 test function: generation of executable code and program start DIN 19244 Telecontrol equipment and remote control systems Part 3 interfaces (electrical characteristics); IEC 60870-3: 1989; German version HD 546.3 S1: 1991 Part 4 requirements for the performance (IEC 60870-4: 1990); German version HD 546.4 S1: 1992 DIN 19260 pH measurement - Common Terms DIN 19261 pH measurement - measurement method using potentiometric cells - Vocabulary DIN 19262 socket and plug shielded for pH Electrodes DIN 19263 pH measurement - pH Electrodes DIN 19265 pH / ORP measurement - pH / ORP transmitter - Requirements DIN 19266 pH measurement - reference buffer solutions for calibration of pH measuring equipment
DIN 19267 pH measurement - Technical buffer solutions, preferably for calibration and adjustment of t measuring equipment
DIN 19268 pH measurement - pH measurement of Aqueous solutions with pH Electrodes pH glass elec estimation of measurement uncertainty
DIN 19277 Graphic symbols of process control DIN 19302 Packaging materials - paper for general packaging - Requirements, testing, DIN 19303 Cardboard - Terms and grade classifications DIN 19306 Paper - Stationery Part 1: General technical delivery Part 2: Technical delivery conditions for offset paper, coated and uncoated, white Part 3: Technical delivery conditions for gravure paper, coated and uncoated Part 4: Technical delivery conditions for newsprint DIN 19307 cardboard and paper - office paper, uncoated, uncoated - Requirements, testing, DIN 19516 Toilet Seats - Requirements and test methods DIN 19522 Cast iron drainage pipes and fittings without socket (SML)
DIN 19523 requirements and test methods for deterministic mining the high-pressure jet resistance an pipe for drains and sewers
DIN 19527 Leaching of solid materials - Batch test for examination of the leaching of organic substanc solid ratio of 2 l / kg DIN 19528 elution of solids - percolation process to joint examination of the leaching of inorganic and
DIN 19529 Leaching of solid materials - Batch test for examination of the leaching of inorganic materi solid ratio of 2 l / kg DIN 19531 Pipes and fittings made of unplasticized polyvinyl chloride (PVC-U) for drains within buildin Part 10 Fire behavior, control and installation Recommendations
DIN 19534 Pipes and fittings made of unplasticized polyvinyl chloride (PVC-U) with spigot and socket f sewerage Part 3 quality control and construction
DIN 19535 Pipes and fittings made of high density polyethylene (HDPE) for hot water resistant sewers buildings Part 10 Fire behavior, quality control and installation Recommendations DIN 19537 pipes, fittings and Manholes of high density polyethylene (HDPE) for drainage and sewerag Part 3 lifting stations; Dimensions and technical delivery
DIN 19538 Pipes and fittings of chlorinated polyvinyl chloride (PVC-C) for hot water resistant sewers (H Part 10 Fire behavior, quality control and installation Recommendations DIN 19541 water seals for special purposes - Requirements and test methods DIN 19551 wastewater treatment plants - Rectangular pool Part 1 settling basins for thyroid, suction and flight scrapers, designs, main dimensions, equipment Part 3 sand traps with suction and Schildräumer, designs, main dimensions, equipment
DIN 19552 wastewater treatment plants - Round Pool - settling tank with shield and suction scraper an designs, main dimensions, equipment DIN 19553 wastewater treatment plants - Trickling filter with rotary distributor - Main dimensions and
DIN 19554 wastewater treatment plants - computational structure with straight rake as Mitstrom- and - Main dimensions, equipment DIN 19555 crampons for single-barrel manhole steps - crampons for installation in concrete DIN 19556 wastewater treatment plants - channelsWithData shut-off - Main dimensions
DIN 19557 wastewater treatment plants - mineral fillers and extenders made of plastic for trickling filt testing, delivery, introduction
DIN 19558 wastewater treatment plants - drainage devices, overflow weir and baffle, drain pipes subm Principles, main dimensions, configuration examples DIN 19559 Flow of wastewater in open channels and gravity lines Part 1: General Information Part 2 venturi channels DIN 19560 Pipes and fittings of polypropylene (PP) for hot water resistant sewers (HT) inside buildings Part 10 Fire behavior, quality control and installation Recommendations DIN 19561 Pipes and fittings made of styrene copolymer for hot water resistant sewers (HT) inside bu Part 10 Fire behavior, quality control and installation Recommendations
DIN 19565 pipes, fittings and shafts made ??of glass fiber reinforced polyester resin (UP-GF) for under sewerage; Finished Manholes Part 5 dimensions and technical delivery, Replaced in March 2013 by DIN EN 15383 DIN 19569 wastewater treatment plants - Principles for the structures and technical equipment Part 2 Specific principles for Means for separating and concentrating solid materials Part 3 Specific principles for equipment for aerobic biological wastewater treatment Part 4 Specific principles for frameless shut-off Part 5 Specific principles for plants for anaerobic treatment of wastewater Part 7 Fäkalschlammübernahmestation Part 8 Specific principles for plants for wastewater treatment with fixed bed filters and biological filter Part 9 Mechanical sludge dewatering Part 10 Specific principles for plants for sewage sludge drying of Part 11 dosing DIN 19571 wallpaper 500 x 500 for road gullies, Class C 250, channel-like Part 1 compilation Part 2 items DIN 19572 fixtures for boarding in walk-shafts - Requirements, testing, DIN 19580 Drainage channels for traffic areas - Durability, unit weight and evaluation of conformity DIN 19583 wallpaper 500 x 500 for road gullies, Class C and Class D 250400 Part 1 compilation Part 2 items DIN 19584 Manhole covers for Manholes, Class D 400 Part 1 compilation Part 2 items
DIN 19585 drainage facilities; Technical delivery conditions for objects cast material, concrete and con with cast material DIN 19590 essays for road gullies, Class A 15 square Part 1 compilation Part 2 items DIN 19593 essays for road gullies, class B 125, square Part 1 compilation
Part 2 items DIN 19594 wallpaper 300 x 500 for road gullies, Class C 250 Part 1 compilation Part 2 items DIN 19596 manhole covers, classes A 15 and B 125, round Part 1 compilation Part 2 frame Part 3 covers DIN 19605 fixed-bed filters for water treatment - Structure and Components DIN 19606 chlorination for water treatment - is planning construction and operational DIN 19624 precoat filter for water treatment DIN 19626 Chemicals used for treatment of water Intended for human consumption - Calcium chloride DIN 19627 Ozone generator for water treatment DIN 19628 Mechanical filters in drinking water installations - Application of Mechanically filters acting 1
DIN 19630 guidelines for the construction of water pipelines; DVGW code of practice of March 2000 Re DIN 19633 ion exchange, adsorption resins and Hybridadsorber for water treatment - Technical delive DIN 19635 dosing in drinking water installations Part 100 requirements for application of dosing nach DIN EN 14812 DIN 19636 Water Softeners (cation exchanger) in the Trinkwasserinstallatio Part 100 requirements for application of water softening systems nach DIN EN 14743 DIN 19643 treatment of swimming pool water Part 1: General requirements Part 2 Combinations of Processes with fixed bed and precoat Part 3 process Combinations with ozonation Part 4 Combinations of methods with ultrafiltration
DIN 19645 Preparation of Spülabwässern from plants for treatment of swimming pool water (currently Located) DIN 19648 Meters for cold water Part 1 Eckwasserzähler Part 2 standpipe water meter Part 3 standpipe water meter DIN 19650 Irrigation - Hygienic Concerns of irrigation water DIN 19653 irrigation equipment - Graphical symbols, symbols, representations, terms, DIN 19655 Irrigation - tasks, basics, planning and procedures DIN 19657 backups of waters, coastal dunes and dikes; Guidelines DIN 19658 Wrap-pipes made of polyethylene (PE) and hoses for irrigation systems Part 2 hoses with textile reinforcement, dimensionally stable, Dimensions and technical delivery cond Part 3 hoses with textile reinforcement, dimensionally unstable; Dimensions and technical delivery co DIN 19660 landscape conservation measures at the Natural Resources and water construction DIN 19661 Hydraulic Structures
Part 1 crossing structures; trans mitted As and mouth Structures Part 2 sole Buildings - Crashes, Crash stairs, ramps sole, sole slip, support thresholds, window sills, thr DIN 19662 Soil quality - Field tests - Determination of resistance to penetration of soils with the Hand DIN 19663 torrents, Concepts, design and construction DIN 19666 Sickerrohr- and Versickerrohrleitungen - General requirements DIN 19667 Drainage of landfills - Design, construction and operational DIN 19682 Soil quality - Field tests Part 1 Determination of soil color Part 2 Determination of Soil Part 5 Determination of moisture condition of the soil Part 7 Determination of infiltration rate with the double cylinder infiltrometer Part 8 Determination of water permeability with the hole-drilling method Part 9 Determination of air permeability Part 10 Description and assessment of soil structure Part 12 Determination of the degree of peat decomposition Determination part 13 of the carbonates, sulfides the, the pH and the iron (II) ion DIN 19683 Soil quality - Physical laboratory tests Part 9 Determination of water permeability in water-saturated soil sample rings soil samples Part 13 Determination of substance fraction, pore fraction and the void ratio Part 14 Determination of substance proportion of peat soils Part 16 Determination of aggregate stability after the screening process so DIN 19684 Methods of soil investigations for agricultural engineering - Chemical laboratory tests Part 3 Determination of loss on ignition and Glührückstands Part 6 Determination of iron oxalatlöslichem Part 7 Determination of soluble ferrous iron Easily Part 9 Determination of sulfides and polysulfides phytopathogenic in the ground Part 10 Investigation and assessment of water in irrigation DIN 19686 Vegetation Ecological data collection in the field of land management for tasks DIN 19687 Soil quality - Calculation of seepage rate from the soil
DIN 19695 transportation and storage of concrete, reinforced concrete and prestressed concrete pipes associated Manholes DIN 19698 waste analysis - Sampling of fixed and random solid waste Part 1 Guidance for the segment-oriented collection of samples from unknown heaps DIN 19700 dams Part 10 Common specifications Part 11 dams Part 12 Detention basin Part 13 barrages Part 14 pumped storage reservoir Part 15 Sedimentationsbecken DIN 19702 Solid structures in hydraulic engineering - Bearing capacity, serviceability and durability
DIN 19703 locks of inland waterways - Principles for dimensions and equipment DIN 19704 Hydraulic steel Part 1 Basis of calculation Part 2 Structural Through education and production Part 3 Electrical Equipment DIN 19706 Soil quality - Determination of the erosion hazard of soil by wind DIN 19707 Soil quality - classification of the nutrient status of soils DIN 19708 Soil quality - Determination of the erosion hazard of soil water by using the USLE DIN 19711 Hydro Geological characters DIN 19712 River dikes DIN 19720 base plates in concrete for road caps; Dimensions, shapes DIN 19731 Soil quality - use of soil material DIN 19732 Soil quality - Determination of the locational shift potential of substances nichtsorbierbaren DIN 19738 Soil quality - resorption of organic and inorganic pollutants from contaminated soil materia DIN 19739 Air and soil quality - Measurement of atmospheric deposition of organic trace substances; method Part 1 Sampling devices, requirements, installation, application Part 2 Determination of polycyclic aromatic hydrocarbons DIN 19741 Soil quality - Determination of contents of platinum group elements (platinum, palladium, materials and sludges
DIN 19745 Soil quality - the basis for the determination of water content by time-domain Reflektomet Domain Transmissometry (TDT)
DIN 19746 Soil quality - Determination of mineral nitrogen (nitrate and ammonium) in soil profiles (Nm method)
DIN 19747 investigation of solids - Sample preparation, preparation and processing of chemical, biolo examinations DIN 19752 hydroelectric plants; Rules for planning and operational DIN 19802 Cast iron fittings for asbestos cement pressure pipes; stem ends for GAZ-pieces DIN 19850 fiber cement pipes and fittings for drainage Part 1 Dimensions of pipes, branches and bow Part 2 dimensions of pipe connections Part 3 bays; Dimensions and technical delivery DIN 19901 Separator systems for light liquids and fats - Proof of ultimate and serviceability limit DIN 20000-29999 [ Edit ] DIN 20000 Application of building products in structures Part 5 Strength graded structural timber with rectangular cross section Part 401 rules for the use of bricks nach DIN EN 771-1: 2011-07 DIN 20002 pipes for the mining industry; Steel tubes with loose flanges and plain collars Part 1 nominal pressure 10 Part 2 nominal pressure 6 Part 3 nominal pressure 40 DIN 20003 pipes for the mining industry; fittings with loose flanges and plain collars
Part 1 nominal pressure 10 Part 2 nominal pressure 6 Part 3 nominal pressure 40 DIN 20004 pipes for the mining industry Part 1 Einschaltringe for nominal pressure PN 10 and PN 40 Part 2 wedge rings for nominal pressure PN 10 and PN 40 DIN 20006 pipes for the mining industry; Flat washers for steel pipes nach DIN 20002 and DIN 20003 DIN 20012 Blasversatzrohre DIN 20013 Gaskets for Blasversatzrohre DIN 20018 hoses with textile inserts Part 1 Maximum working pressure PN 10/16 Part 2 Maximum working pressure PN 40 Part 3 Maximum working pressure PN 100 Part 4 test DIN 20021 Hydraulic fluid power - Hoses with layer - supplement to DIN EN 853 and DIN EN 857 DIN 20029 pant-end fittings; taper gauges, taper 1: 3 DIN 20030 pant-end fittings; flow cock with tap handle, Dimensions, materials, requirements DIN 20033 pant-end fittings; Kegeltülle with union nut DIN 20035 pant end fittings, Flanged; nominal pressure 16 DIN 20036 pant-end fittings; Connecting nipple with standard thread DIN 20037 pant-end fittings; nipple; Mass DIN 20038 pant-end fittings; Verbindungstüllen DIN 20039 pant-end fittings - Hose Clamps DIN 20040 pant-end fittings; Nipple valve; nominal pressure 16 DIN 20042 water valve, nominal pressure 40 - Dimensions and requirements DIN 20043 connectors for hydraulic hose assemblies - Dimensions, requirements, testing DIN 20044 connectors Type S for hydraulic hose assemblies - Dimensions, requirements, testing DIN 20066 Hydraulic fluid power - Hose assemblies - Dimensions, requirements DIN 20097 gear for coal plow and chain conveyors underground; Signs gear ratios DIN 20109 Kreuzhacke DIN 20110 tamping pickaxe DIN 20112 Spitz Scratch DIN 20115 pit Hatchets DIN 20119 slides blades DIN 20120 Sand Buckets DIN 20121 piercing blades DIN 20123 edge blades DIN 20124 socket blades DIN 20125 filling blades DIN 20127 spade DIN 20128 flat edge blades
DIN 20129 leaf blades DIN 20135 Treibfäustel DIN 20136 mallet DIN 20142 hacksaws U-bolts and two handles DIN 20151 shovel handle 1300; Dimensions, requirements, testing, marking DIN 20152 Grip Handles for shovels and spades, shapes, dimensions, requirements, testing, marking DIN 20163 blasting operations DIN 20164 Explosive - Explosive Weather Part 1 Requirements, testing, marking DIN 20165 Blasting supplies - Intrinsically safe detonators (Permitted detonators) - Requirements and
DIN 20166 Blasting supplies - Intrinsically safe detonation cords (weather Detonating cords) - Safety r testing DIN 20180 Pulley for clothes in pithead baths DIN 20182 node chain for clothes in pithead baths - Not tested, non-calibrated DIN 20301 rock drilling - definition, units and symbols DIN 20302 Gesteinsbohreinrichtungen; Terms DIN 20311 drill pipes for large hole drilling in mining than 100 mm diameter DIN 20314 Thread drill pipe 100 mm diameter for large hole drilling in mining DIN 20316 rock drilling - threaded connections for thin-walled rotary drilling equipment - Dimensions, DIN 20317 rock drilling - Round screw connections for Schlagbohrgestänge - Dimensions, design DIN 20350 Cutting mining and tunneling machines; Shanks of cutting tools and Their installation dime DIN 20361 rock drilling - drill bushings - Connecting dimensions, material, design DIN 20367 rock drilling - Round screw connections for rotary drilling equipment - Dimensions, design DIN 20369 Demolition Hammer, Flat and Abschermeißel without and with shank DIN 20371 rotary hammers; Connection pin for hammer drill support DIN 20372 ROCK DRILLING; flush pipe; Connecting dimensions, material, design DIN 20374 Demolition Hammer; Lessons for chisel DIN 20375 Demolition Hammer, Pointed chisel shank without DIN 20376 Demolition Hammer, Pointed chisel with shank DIN 20377 rock drilling - Spülbohrstangen - Bohrstangenprofile, shanks, cone DIN 20378 rotary hammers; Taper gauges for Bohrstangen- and wellhead cone DIN 20379 rock drilling Part 1 percussive with inner cone for Spühlbohren Part 2 percussive with female thread for Spühlbohren DIN 20400 Round threads for mining; thread with great load-bearing depth DIN 20401 buttress thread - pitch 0.8 mm to 2 mm - Dimensions DIN 20449 turnouts and crossovers for underground mines; Overview, concepts DIN 20450 Simple underground track; 20 m radius, 1: 5 inclination; Geometric Dimensions DIN 20452 Part 1 Simple underground tracks with loose heel; 20 m radius, 1: 5 inclination, 600 mm gauge; Comp Part 2 Simple underground tracks with spring switch blade; 20 m radius, 1: 5 inclination, 600 mm gau
DIN 20453 Part 1 Switches for simple underground tracks with loose heel; 20 m radius, 1: 5 inclination, 600 mm g Part 2 switches for simple underground tracks with spring switch blade; 20 m radius, 1: 5 inclination, 6 DIN 20454 Crossings for simple underground track points; 20 m radius, 1: 5 inclination, 600 mm gaug DIN 20455 Radlenkervorrichtungen for simple underground track points; 20 m radius, 1: 5 inclination, DIN 20458 Simple underground tracks; 20 m radius, 1: 5 inclination; Geometric Dimensions DIN 20460 Simple underground track; 30 m radius, 1: 6 inclination; Geometric Dimensions DIN 20462 Part 1 Simple underground tracks with loose heel; 30 m radius, 1: 6 inclination, 600 mm gauge; Comp Part 2 Simple underground tracks with spring switch blade; 30 m radius, 1: 6 inclination, 600 mm gau DIN 20463 Part 1 Switches for simple underground tracks with loose heel; 30 m radius, 1: 6 inclination, 600 mm g Part 2 switches for simple underground tracks with spring switch blade; 30 m radius, 1: 6 inclination, 6 DIN 20464 Crossings for simple underground track points; 30 m radius, 1: 6 inclination, 600 mm gaug DIN 20465 Radlenkervorrichtungen for simple underground track points; 30 m radius, 1: 6 inclination, DIN 20468 Simple underground tracks; 30 m radius, 1: 6 inclination; Geometric Dimensions DIN 20470 Simple underground track; 50 m radius, 1: 7 inclination; Geometric Dimensions DIN 20472 Part 1 Simple underground tracks with loose heel; 50 m radius, 1: 7 inclination, 600 mm gauge; Comp Part 2 Simple underground tracks with spring switch blade; 50 m radius, 1: 7 inclination, 600 mm gau DIN 20473 Part 1 Switches for simple underground tracks with loose heel; 50 m radius, 1: 7 inclination, 600 mm g Part 2 switches for simple underground tracks with spring switch blade; 50 m radius, 1: 7 inclination, 6 DIN 20474 Crossings for simple underground track points; 50 m radius, 1: 7 inclination, 600 mm gaug DIN 20475 Radlenkervorrichtungen for simple underground track points; 50 m radius, 1: 7 inclination, DIN 20478 Simple underground tracks; 50 m radius, 1: 7 inclination; Geometric Dimensions DIN 20499 tracks in underground mines - General Rules DIN 20500 pit lanes, track gauges and rails; Overview and Selection DIN 20501 pit lanes; S rails 30, splice plate 30 Fl DIN 20506 Clamp for mounting rails on steel materials DIN 20536 standard turnout with spring switch blade; radius of 120 m, slope 1: 9, track-gauge 900 mm DIN 20537 switch device for easy points; radius of 120 m, slope 1: 9, track-gauge 900 mm DIN 20539 wheel guide for easy points; radius of 120 m, slope 1: 9, track-gauge 900 mm DIN 20548 wheelsets for railway vehicles for underground mines; Rules for measuring DIN 20549 trace dimensions for pit lanes, Terms and tolerances DIN 20550 small trolley, Compilation, main dimensions, design DIN 20551 Tram - end cap, coat, framebuffer plate DIN 20552 small trolley; Buffer support web DIN 20553 tapered roller bearing sets of wheels for trolleys - unsprung execution DIN 20555 tapered roller bearing sets of wheels for trolleys, externally jump execution DIN 20556 tapered roller bearing sets of wheels for trolleys, internally jump execution
DIN 20560 Central tram; Dimensions, design DIN 20570 United tram; Dimensions, design DIN 20575 track promotion - cars for underground mines Part 1 requirements DIN 20579 buffer springs for trams Part 1 calculation Part 2 requirements DIN 20581 Tram; Flap clutch DIN 20583 Tram - Shackles coupling DIN 20586 rail fastenings in mining for rails 30E1 33E1 and on wooden sleepers DIN 20590 fixtures on chassis for mining DIN 20592 monorails for mining Part 1 shipping container; Dimensions and requirements Part 2 anchor devices for transport containers; Dimensions and requirements DIN 20593 Monorails for mining - Rails Part 1 Straight rails for the profile I 140 E Part 2 curved rails and connecting bars for the profile I 140 E Part 3 Straight rails and rail links to the profiles I 140 V and I 250 Part 4 curved rails and connecting bars for the profiles I 140 V and I 250 DIN 20594 branch hooks for the mining industry for weight forces up to 30 kN; Requirements and test DIN 20597 monorails for mining; disk with teeth DIN 20599 monorails for mining; position of the pull cable, roller block holder, gauge for trolleys DIN 20600 mining trains - profiles for wheels of locomotives and wagons DIN 20601 pit lanes; Tires of the wheels of locomotives
DIN 20609 lights on mine locomotives, Head Lights, design features, lighting requirements, measuring measurements DIN 20610 lights on mine locomotives; Light for parking light; Design features, lighting requirements DIN 20619 monorails for mining; Cable drum with a hanger; Dimensions and requirements DIN 20620 with forcibly guided rail tracks in underground mines Part 1 Overview, Structure and terms Part 2 monorails; Structure and terms Part 3 rail corridor tracks; Structure and terms
DIN 20622 Monorails for mining - Permissible trailer loads for railway suspensions and Their abutment profile I 140 E DIN 20625
Part 1 forcibly guided rail systems for mining; Drawbar couplings for rope-driven and self-powered rail 30 DIN 20629 Monorails for mining - hanging rails Part 1 for cable-operated monorails Part 2 for self-powered monorail conveyors Part 3 Basis of calculation DIN 20633 Monorails for mining - turnbuckles, bothsides with fork ends
DIN 20635 Monorails for mining - shackle hangers DIN 20636 Monorails for mining - branch hooks; Requirements and tests DIN 20637 Monorails for mining - round steel chains for suspensions, tested, long-limbed DIN 21151 Shaft sinking - pulleys for flat winding ropes - Safety requirements and testing DIN 21164 Shaft sinking - guide carriage - Safety requirements and testing DIN 21181 Shaft sinking - Debris kibbles Part 1 Debris kibbles with strap suspension Part 2 Debris kibbles with suspension two ring chain DIN 21186 Shaft sinking - pulley block for load hoisting in shafts DIN 21187 Shaft sinking - chain slings for load hoisting in shafts DIN 21194 cable end in radial insert ball bearings for guide ropes - Safety requirements and testing DIN 21198 Shaft sinking - Shaft solders DIN 21258 Lubricating and friction hoist ropes in Tränkungsstoffe for mines - Safety requirements and DIN 21315 pit logs; Sustainability of stamps and caps; Calculation DIN 21316 pit logs, Stamp, caps DIN 21317 pit logs, sticks, tips DIN 21318 pit logs, wood box (wood pillars) DIN 21319 pit logs; Bolt DIN 21320 pit logs; Technical Quality and Delivery DIN 21321 pit sawn timber; Timber DIN 21324 pit sawn timber; Pillar blocks DIN 21325 pit sawn timber - timber sleepers DIN 21326 pit sawn timber, boards, planks DIN 21327 pit sawn timber, Running boards, planks and scantlings stand for stages DIN 21328 pit sawn timber; Rinds DIN 21329 pit sawn timber; Technical Quality and Delivery DIN 21341 trace slats of wood DIN 21346 square head bolts for track slats DIN 21371 Between harnesses; Compilations DIN 21376 Part 1 guide shoes for funding and balances with roller guides in mining Part 2 guide shoes for funding and balances with sliding mining DIN 21377 Stainless steel railing for funding mining DIN 21381 Between harnesses; Tabs for round thimbles DIN 21382 Between harnesses; Outer plates, inner plates DIN 21383 Between harnesses; Bolt DIN 21386 Between harnesses; Thimbles for round cables DIN 21388 Between harnesses; universal joint pieces DIN 21389 Between harnesses; Clamping Thimbles DIN 21390 Thimbles for flat ropes DIN 21500 shaft lining in mining - Design and dimensioning
DIN 21521 rock bolts for mining and tunneling Part 1 Definitions Part 2 General requirements for steel-bolts, tests, test procedures DIN 21522 anchor plates for the mining and tunneling DIN 21530 for mining expansion Part 1 General Part 2 dimensions, designation and static values Part 3 requirements Part 4 exams Part 5 Identification of upgrade parts DIN 21531 Rigid arch supports Part 1 sheets B 5.4 to B 20.2 Part 2 sheets B to B 21.7 63 DIN 21546 mine roof; Longwall; Identification DIN 21548 rails for mining operations DIN 21549 mine roof; Terms for roof supports DIN 21550 mine roof; Steel caps for individual temples; Examination requirements DIN 21551 mine roof; Steel caps for individual temples; Lengths DIN 21555 mine roof; Graphical symbols for control of powered roof DIN 21556 mine roof; Props valves; Identification DIN 21557 mine roof; Pressure relief valves for roof supports; Identification DIN 21561 mine roof; Head plate for single temple; Connecting dimensions DIN 21577 Mixtures DIN 21603 DIN 21605 DIN 21606 DIN 21610 DIN 21612 DIN 21613 DIN 21614 DIN 21615 DIN 21625 DIN 21626 DIN 21631 DIN 21632 DIN 21633 DIN 21634 DIN 21635 DIN 21636 DIN 21637
Risks of explosion of coal dust in coal mines - testing and evaluation of coal dust-air Mixtur
for mining - ventilation ducts made of sheet steel with collars and loose flanges for mining - Flexible plastic for exhaust and forced ventilation - Spiral air ducts for mining - Flexible plastic for blowing ventilation - air ducts Flat for mining - Flexible plastic - Requirements and tests for mining - Sheath material for Flexible plastic - Requirements, testing, for mining - fittings made of sheet steel - bead flange for mining - transition pieces of sheet steel - flange to flange for mining - transition pieces of sheet steel - bead flange electric fans Potentially explosive atmospheres for use in mines of coal Combined fans Potentially explosive atmospheres for use in mines of coal Weather in mining - Doors for the infrastructure - without pressure reduction weather door Weather in mining - wing doors for haulage - without pressure reduction weather doors Weather in mining - wing doors for haulage - Non pressure balanced double-leaf doors Wea Weather in mining - Weather swing doors for haulage Weather in mining - Weather locks - Construction and Operational Weather in mining - Gurtfördererschleusen - Dimensions, designation, requirements and te Weather in mining - wing doors for haulage - Pressure balanced double-leaf doors Weather
DIN 21638 Weather in mining - Doors for the track - Pressure balanced double-leaf doors Weather DIN 21639 Weather in mining - track locks - balanced mechanical ventilation doors DIN 21640 in mining; Air cylinder for Unbalanced ventilation doors Part 1 Dimensions, requirements, marking DIN 21772 Gears - Cylindrical gears with involute gears and cylinder gear - Definition of Deviations DIN 21773 Gears - Cylindrical involute gears and cylinder gear - check dimensions for the tooth thickn DIN 21800 characters "hammer and chisel" (mining icon) DIN 21802 characters of mine rescue and gas protection weirs DIN 21901 Mine Plan; Structure and Overview of standards; General principles Part 2 interface for computer-assisted takeover of characters of the mining Rißwerkes DIN 21902 Mine plans - Structure of mining Rißwerkes Part 2 completion of planned works DIN 21903 Mine plans - format and folds DIN 21904 Mine Plan; Writings DIN 21905 Mine Plan; Graphical Basics DIN 21906 Mine Plan; Page layouts DIN 21907 Mine plans - sheet design DIN 21908 Mine Plan; Colors DIN 21909 Mine plans - survey points and lines DIN 21910 for mining - Flexible plastic - Requirements and tests DIN 21911 Mine plans - day objects and contour lines DIN 21913 Mine Plan; Civil Engineering Part 1 mines Part 2 reduction, offset and storage Part 3 Conclusion of mine workings Part 4 hazard and protection areas Part 6 Safekeeping of mining produced hollows Part 7 Bay image DIN 21914 Mine plans - holes and caverns Part 1 Holes Part 2 Solkavernen DIN 21915 Mine plans - Technical Equipment DIN 21916 Mine plans - Operational safety Part 1 Ventilation and Meteorology Part 2 fire for days Part 3 fire prevention under the DIN 21917 Mine plans - mountain and ground movements Part 2 geomechanical monitoring stations DIN 21918 Mine plans - Mineral deposits Part 1 Concepts and Classification Part 2 widths
DIN 21919 Mine plans - Stratigraphy Part 1 General organization Part 2 Regional and local subdivisions - Coal Part 3 Regional and local subdivisions; Lignite DIN 21920 Mine plans - petrography Part 1 General Characters - sediment Part 2 Magmatite Part 3 Metamorphic and other Gesteinsumbildungen Part 4 minerals Part 5 coal industry Part 7 of potash and rock salt mining DIN 21921 Mine plans - Tectonics and shape description of rock strata DIN 21961 Markscheidewesen - spigot, slip-on for Hängetheodolite - Connecting dimensions DIN 22005 Investigations of raw material in the coal industry Part 1 Overview Part 2 terms Feedstock DIN 22011 Investigations of raw material in the coal industry; Processing of test holes
DIN 22012 Investigations of raw material in the coal industry; Macro petrographic approach and inclus country rock DIN 22013 Investigations of raw material in the coal industry; Channel sample; Removal and Untersuc
DIN 22014 Investigations of raw material in the coal industry; Rohkohlenprobe from the conveyed at o Removal and examination scheme
DIN 22015 Investigations of raw material in the coal industry; Macroscopic response and uptake of the overburden DIN 22017 Investigations of raw material in the coal industry - Flotationsanalyse
DIN 22018 Investigations of raw material in the coal industry; Determination of particle density distrib and Sinkanalyse DIN 22019 Investigations of raw material in the coal industry Part 1 Determination of particle size distribution, grain size distribution of> 20 microns by sieve analy
DIN 22020 Investigations of raw material in the coal industry - Microscopic examination of hard coal, c Part 1 Definitions, overview and application of the method Part 2 production of grains cuts and cuts piece Part 3 Maceralanalysen of grains cuts Part 4 Mikrolithotypenanalyse of grains cuts Part 5 of Vitrinite reflectance measurements
DIN 22021 Investigations of raw material in the coal industry; Division of the host rocks due to micros identify technological properties DIN 22022 Solid fuels - Determination of trace elements
Part 1: General rules, sampling and sample preparation; Preparation of the test sample for determinis process) Part 2 ICP-OES
Part 3 flame AAS technique Part 4 atomic absorption spectroscopy using the hydride or cold vapor technique Part 5 atomic absorption spectroscopy using the graphite furnace technique Part 6 evaluation and reporting of test results DIN 22024 Investigations of raw material in the coal industry; Determination of Tensile splitting streng DIN 22100 equipment and materials from synthetic for use in underground mines Part 1 Conveyor belts - Hygiene requirements, testing, marking Part 3 Spiral air ducts - Safety requirements, testing, marking Part 4 Flat air ducts - Safety requirements, testing, marking Part 5 tubes, tube isolations and hoses - Safety requirements, testing, marking Part 6 films, coated / uncoated fabrics, materials and lagging mats - Safety requirements, testing, mar Part 7 Safety requirements, testing, marking DIN 22101 Belt conveyors for bulk foundations calculation and interpretation DIN 22102 textile conveyor belts for bulk materials Part 1 Dimensions, requirements, marking Examination Part 2 Part 3 Non detachable belt splices DIN 22107 bearing roller assemblies for belt conveyors DIN 22109 textile conveyor belts for the coal industry Part 1 conveyor belts with to insert for underground; Dimensions, requirements Rubber conveyor belts Part 2 with two plies for underground; Dimensions, requirements Rubber conveyor belts Part 4 with two liners for above ground; Dimensions, requirements Part 5 Marking Part 6 tests DIN 22110 test method for conveyor Part 2 endurance trial, deterministic mining the term of splices of textile conveyor belts Part 3 Determination of the time strength for conveyor (dynamic test method) DIN 22111 Belt conveyors for underground coal mining - Lightweight shoring DIN 22112 supporting role: Dimensions, requirements, testing DIN 22114 Belt conveyors for underground coalmining - Heavy Shoring DIN 22115 Belt conveyors for the coal mining - coatings on Idlers - Requirements and test methods
DIN 22116 Belt conveyors for the coal mining - pressure rollers with a nominal diameter 159 mm - Dim requirements, marking DIN 22117 Conveyor belts for the coal industry; Determination of the oxygen-characteristic value DIN 22118 textile conveyor belts for the coal industry; Fire Testing DIN 22120 squeegee made of elastomers for belt conveyor in coal mines
DIN 22121 textile conveyor belts for the coal industry - Non detachable belt splices for conveyor belts deposits; Dimensions, requirements, marking
DIN 22122 Continuous handling equipment - trough ability of conveyor belts - Determination of the pr with a conveyor belt rests on the support rollers; Requirements, testing, DIN 22123 Conveyor belts - Gurtbreitenbezogener Eindrückrollwiderstand of conveyor belts - Requirem DIN 22129 steel cord conveyor belts to the underground coal mining
Part 1 dimensions, requirements Part 2 labeling Part 3 tests Part 4 splices; Dimensions, requirements DIN 22131 steel cord conveyor belts for general Conveying Technology Part 2 labeling Part 3 tests DIN 22200 Continuous handling equipment, conveyors link; Principles of calculation DIN 22252 round steel chains for conveyors and mining equipment in mining DIN 22253 connectors Chain - U-locks - Dimensions, requirements, testing DIN 22255 flat chains for conveyors in mining DIN 22256 Sprockets for chain conveyors and mining equipment - Dimensions, requirements, testing DIN 22257 for chain conveyors scratch; Outer chain belt, Dimensions, requirements, testing DIN 22258 chainlinks Part 1 flat locks Part 2 Kenter locks Part 3 block locks DIN 22259 drivers for chain conveyors in mining DIN 22261 excavators, spreaders and auxiliary equipment in opencast lignite mines Part 1 construction, commissioning and testing Part 2 Basis of calculation Part 3 welded joints, shock types, review groups, test instructions Part 4 Mechanical brakes for winches Part 5 Mechanical brakes and overload protection for slewing Part 6 Examination of ropes and rope terminations DIN 22270 Continuous Surface Miner (CSM) - Security DIN 22400's cabs for carriers; Förderhäspeln and winches in the mining industry DIN 22405 traction sheave feed for carriers and Förderhäspel in mining DIN 22406 Traction-type hoisting winch for manhole and inclined conveyors; Brake calculation DIN 22410 conveyor pulleys for round ropes
DIN 22416 Flame-proof and explosion-proof electrical equipment for the mining industry; Dreikantvers requirements and testing DIN 22417 Flame-proof and explosion-proof electrical equipment; Key shapes for three-point socket w DIN 22418 Flame-proof and explosion-proof electrical equipment and testing DIN 22419 Flame-proof and explosion-proof electrical equipment Part 1 Safety requirements and testing Part 2 spacers for introductions; Safety requirements and testing Part 3 flanges for entries; Safety requirements and testing DIN 22424 Flame-proof and explosion-proof electrical equipment DIN 22425 Flame-proof and explosion-proof electrical equipment DIN 22433 lighting in the coal mining - terms
for the mining industry; Screw caps; for mining - Tutorials for cables
for the mining industry; Three head for the mining industry; Dreikantmut
DIN 22434 lighting in the coal mining - Lighting design basics Part 1: General requirements Part 2 Longwall with shield support Part 3 transition regions longwall / route Part 4 Belt Conveyors Part 5 material transfer points Part 6 range tunneling Part 7 Füllörter Part 8 sites Part 9 areas with rail operational Part 10 workshops and special rooms DIN 23004 coal preparation Part 1 Overview Part 2 Procedural terms DIN 23005 hard coal; Description and evaluation of Rohstoffeigenschften for processing DIN 23006 hard coal - Assessment of preparation equipment and procedures Part 1: General rules, mass balances Part 2 Classification Part 3 sorting Part 4 solid-water separation Part 5 Grinding and Unlocking accidental crushing Equalization Part 6 DIN 23007 Preparation of hard coal - waste water treatment for industrial water - Definitions, requirem DIN 23008 hard coal; flotation; Definitions, requirements, testing DIN 23009 hard coal, heavy materials; Definitions, requirements, testing DIN 23011 hard coal; Treatment plants Part 2 flow sheets Part 3 Graphical symbols for flow sheets Part 4 Technical agreements in the definition of warranties Part 5 Procedural monitoring Establishing and Maintaining Part 6 of operating laboratories Part 7 machines Technical Supervision Part 8 Procedural requirements for treatment facilities DIN 23301 safety shoes for underground mining DIN 23307 buttocks leather for mining ( ass leather ) DIN 23311 Knee pads for mining Part 1 of rubber Part 2 of plastic
DIN 23320 flame protective clothing for the mining industry - Protective clothing for miners' Gasschut departments Part 1 Safety requirements and tests
Part 2 One-piece suits (Combinations) Two-piece suits Part 3 DIN 23323 Badepantinen for mining DIN 23327-around lower leg protectors for mining DIN 23328 clothing for the mining industry - fabrics for industrial Suits DIN 23330 Safety signs for the mining industry DIN 23341 Clothing for mining - Two-piece overalls (jacket and trousers) DIN 23342 clothing for the mining industry - men's undershirt quarter-length sleeves DIN 23343 Clothing for mining - mining shirt DIN 23344 Clothing for mining - Men's Slip DIN 23345 clothing for the mining industry - men's underpants 1/1 long DIN 23346 Clothing for mining - Work Socks DIN 23400 extricator for mining (grinding basket) - Safety requirements and testing DIN 23405 Association containers and first aid equipment for the mining industry DIN 24041 perforated plates - Dimensions DIN 24063 actuators (Einrückorgane) for pneumatic tools, terms, safety requirements and testing DIN 24080 Earth-moving machinery, hydraulic excavators, crawler cranes terms DIN 24100 quarrying and construction; Mechanical crushing Part 1 Procedure Technical terms Part 2 machines terms, size specifications DIN 24117 quarrying and construction - boom for concrete pumps - Principles of calculation and stabil DIN 24118 quarrying and construction - concrete delivery lines - Dimensions and calculation DIN 24166 fans; Technical delivery conditions DIN 24189 test air filters for internal combustion engines and compressors; Test methods DIN 24193 ducting for ventilation systems Part 1 - angle flanges Series 1 Part 2 - Angle flanges Series 2 DIN 24201 Furnaces; reheating furnaces and heat treatment; Terms DIN 24250 centrifugal pumps; Naming and numbering of components DIN 24251 multistage centrifugal pumps, drainage pumps at rated speed is 1500 l / min, with head up DIN 24259 pumps, base plates for machines Part 1 Dimensions DIN 24271 central lubrication technology - Vocabulary Part 1 classification Part 2 Graphical symbols for technical drawings Part 3 Technical parameters and units DIN 24273 Pumps and pump units for liquids - Material and construction tests DIN 24289 Reciprocating positive displacement pumps and aggregates Part 1 Technical specifications Part 2 Technical specifications, data for a datasheet DIN 24290 jet pumps, Concepts and Classification
DIN 24291 jet pumps, Nomenclature of components DIN 24296 Pumps and pump units for liquids - Spare Parts - selection and procurement DIN 24299 nameplates for pumps Part 1 General requirements DIN 24311 Hydraulic fluid power, hydraulic proportional valves, Words, symbols, units DIN 24320 Flame-resistant fluids - liquids pressure categories HFAE and HFAS - Properties and requirem DIN 24336 Hydraulic fluid power, hydraulic cylinder 100 bar, connection dimensions
DIN 24339 Hydraulic fluid power, hydraulic reservoirs made ??of steel; Dimensions, requirements, tes 63-1250 DIN 24340 Hydraulic valves Part 2 holes and connecting plates for the mounting of directional control valves DIN 24343 Hydraulic fluid power, hydraulics, maintenance and inspection list for hydraulic systems DIN 24374 Surface Technology; Determination of the characteristic curves for the pump Part 1 pneumatically driven piston pump DIN 24375 Surface Technology; flat spray nozzles for spray guns luftloszerstäubende; Dimensions, tes DIN 24420 Parts DIN 24446 Safety of machinery - Vehicle wash - Safety requirements and testing DIN 24450 machines for processing of plastics and rubber; Terms DIN 24480 Die Casting Machines Part 1 machine types, terms, Part 2 modules terms Part 3 machine parts, concepts Part 4 characteristics, terms DIN 24482 horizontal cold chamber die casting machines, Sizes, main dimensions DIN 24500 Rolling Mills Part 1 Overview of the terms Part 3 Designation of rolling mills Part 4 Determination of the rolling mills and rollerdrives Part 5 terms of cooling and lubrication systems for rolling Part 6 terms of cooling Means for rolling Part 7 terms of directing Means and routes Part 8 terms of installations for stacking Part 9 terms of facilities for unstacking Part 10 terms of the facilities for wrapping, collecting, bundling, binding and packaging Part 11 terms of transport and guides Part 12 terms of the separators Part 13 scrap processing facilities terms of Part 14 terms of descaling in hot rolling mills Part 15 terms in other entities DIN 24531 gratings as stages Part 1 gratings made of metallic materials
Part 2 metal planks made of metallic materials Part 3 plastic gratings DIN 24534 Chain Block
DIN 24536 metallurgical plant and rolling mill equipment, Graphical symbols for stone bolts and head plates in technical drawings DIN 24537 gratings for flooring Part 1 gratings made of metallic materials Part 2 metal planks made of metallic materials Part 3 plastic gratings DIN 24539 metallurgical plant and rolling mill equipment, anchor plates for anchor bolts DIN 261 Part 1 single anchor plates, Dimensions, designation, installation depths Part 2 double-anchor plates, Dimensions, designation, installation depths DIN 24540 rod and tube presses for non-ferrous metals and Their this Part 1 General Part 2 application "alloy", press size, tool allocation Part 3 application "heavy metal", press size, tool allocation DIN 24541 metallurgical plant and rolling mill equipment, pipes Recess for anchor plates, Dimensions DIN 24550 Hydraulic fluid power - Hydraulic Filters Part 1 terms, nominal surrounding pressures, nominal sizes, mounting dimensions Part 2 filter elements and filter housing; assessment criteria, requirements Part 3 filter elements for line filters; Overall dimensions Part 4 filter elements for return-line filter; Overall dimensions Part 5 mounted return line filters, connection dimensions Part 6 Prüffiltergehäuse; Mass Part 7 replaceable filters; assessment criteria, requirements Part 8 replacement filters, filter and connection dimensions DIN 24554 Hydraulic fluid power, hydraulic cylinder 160 bar compact; Connecting dimensions DIN 24555 Hydraulic fluid power; Rod ends with narrow spherical bearings; Connecting dimensions DIN 24556 Hydraulic fluid power; Fork Rear axle bracket and holder; Connecting dimensions DIN 24557 Hydraulic fluid power; Breather filter Part 2 connecting dimensions DIN 24564 Hydraulic fluid power - Components for hydraulic systems Part 1 Characteristics Part 2 parameters for electrical displacement measuring system for hydraulic cylinders
DIN 24567 Hydraulic fluid power - Round hydraulic reservoirs made of steel - Dimensions, requiremen Nominal sizes from 1,000 to 20,000
DIN 24602 Magazine pallets of metal; nominal sizes from 400 mm × 600 mm; use in automated flexib DIN 24900 symbols for mechanical engineering Part 12 sewing machines Part 20 Plastics and Rubber Machinery Part 23 die casting machines
DIN 24901 Graphical symbols for technical drawings for mechanical engineering Part 3 shredders; Presentation in flow images Part 4 compressors, fans, Presentation in flow images DIN 24902 Graphical symbols for public information Part 11 elevators Part 20 plastic machines DIN 24950 Fluid Power Part 1 pant lines, concepts DIN 24970 service machines - Ticket machines - Vocabulary DIN 24971 service machines - Ticket machines - Housing dimensions, attachment, materials DIN 24972 service machines - Ticket machines - Requirements for operating and display elements DIN 24973 service machines; Requirements for assemblies for cash processing
DIN 24974 service machines - Ticket machines - Requirements for identification, providing information DIN 24975 service machines - Ticket machines - General requirements for the Gebrauchstauglichtkeit DIN 24976 service machines, ticket machines; Tickets DIN 25003 Railway applications - Classification of rail vehicles - Overview, terms, definitions DIN 25005 rail vehicles - Representation Rules - direction of orientation, component identification DIN 25008 rail vehicles - Principles for the determination of the vehicle mass - Terms, symbols, values DIN 25043 Railway applications - Measuring of new railway vehicles Part 1 Measurement Basics Part 2 measuring operations on car bodies of coaches and railcars, with CD-ROM Part 3 measuring operations on car bodies of locomotives and powerheads, with CD-ROM Part 4 Measurement and calculation of forces acting at the interface between body and running gear, Part 5 Measuring methods at chassis frame, with CD-ROM Part 6 Measuring methods at bolster / cross bar of the chassis Part 7 Measuring methods at complete bogies under compression, with CD-ROM Part 8 Measuring Processes for bodies put on running gear DIN 25108 commuter rail vehicles; Connection and installation dimensions for electromagnetic rail bra DIN 25112 commuter rail vehicles; Wheel tire profile Part 1 width 95 and 110 mm Part 2 profile B, width 95 and 115 mm Part 3 profiles C, 135 mm wide DIN 25124 manipulators of manhole covers , Part 1 to Part 3 DIN 25150 rail vehicles, Interiors, Design requirements for cleaning DIN 25192-head bolts for rail vehicles DIN 25193 rail vehicles - clamp screws with ISO metric thread - Product grade C DIN 25195 rail vehicles - ribs screws with ISO metric thread - Product grade C DIN 25200 bolts and nuts for railway vehicles - Overview DIN 25201 Design guide for railway vehicles and Their components - Bolted joints Part 1 classification, categories of screw connections
Part 2 Design - Mechanical Applications Part 3 Construction - Electrical Applications Part 4 Securing screw connections Part 5 corrosion protection Part 6 connection dimensions Part 7 installation DIN 25250 rail vehicles - car seat - Main dimensions, finishes DIN 25252 rail vehicles; Selbstentladewagen with side panel flaps; Square wave for closure DIN 25255 rail vehicles - Square key for semi-trailers - Dimensions DIN 25256 rail vehicles - Closing aid for articulated vehicles - Dimensions DIN 25401 terms of nuclear technology Part 1 Physical and chemical fundamentals Part 2 reactor design Part 4 nuclear materials Part 5 Fuel Technology Part 7 safety of nuclear installations DIN 25403 criticality in the processing and handling of nuclear fuel Part 1 Principles Part 2 Kritikalitätsdaten for uranium metal 235 light-water Mixtures Part 3 Kritikalitätsdaten for plutonium-239 metal light-water Mixtures Part 4 Kritikalitätsdaten for uranium dioxide light-water Mixtures Part 5 Kritikalitätsdaten for plutonium-239 dioxide light-water Mixtures Part 6 Kritikalitätsdaten for plutonium nitrate-239 light-water Mixtures Part 7 Kritikalitätsdaten for low-enriched uranium dioxide bar grating in water Part 8 Kritikalitätsdaten uranyl nitrate for (100% uranium 235) -Leichtwasser Mixtures DIN 25404 nuclear technology; Symbols DIN 25405 considerations for the safe design of thermal reactors with respect to the Reaktivitätsverha DIN 25407 Shielding walls against ionizing radiation DIN 25410 Nuclear facilities - Surface cleanliness of components DIN 25412 Laboratory equipment - glove boxes Part 1 dimensions and requirements Part 2 leak tests DIN 25413 classification of Abschirmbetonen nach proportions of elements Part 1 of neutron radiation shielding Part 2 of gamma radiation shielding DIN 25415 decontamination of radioactive contaminated Surfaces; Method for testing and evaluation DIN 25419 event flow analysis; Method, graphical symbols and evaluation DIN 25420 construction of hot cells concrete Part 1 Requirements for hot cells for the remote-controlled surgery Part 2 requirements for process and storage cells
Part 3 Requirements for radiation shielding windows for concrete walls of different densities; Mounting Part 4 requirements for radiation shielding windows for concrete walls of density 2.3 g / cm 3 different
DIN 25422 preservation and storage of radioactive materials - Requirements for storage devices and T facilities for radiation, fire and theft protection DIN 25424 Fault Tree Analysis DIN 25425 radionuclide Part 1 Rules for construction Supplement 1 embodiments Part 3 rules for preventive fire protection Part 4 rules for the protection of persons
Supplement 1 Notes on the preparation of a radiation protection instructions for the handling of radioa radionuclide Supplement 2 Notes for shielding photon and beta radiation DIN 25426 Sealed radioactive sources Part 3 leak test in the context of production and type testing Part 4 leak testing whileworking DIN 25430 Safety marking in radiation protection DIN 25432 pipe penetrations through the reactor containment vessel DIN 25433 labeling of fuel for power reactors DIN 25435 Periodic inspections of the components of the primary circuit of light water reactors Part 1 Mechanized Ultrasonic Testing Part 2 magnetic particle and liquid penetrant Part 3 Pressure Test Part 4 visual inspection Eddy current inspection Part 6 of steam generator tubes heating Part 7 radiographic examination DIN 25440 classification of rooms in the controlled area in nuclear installations and facilities nach loca DIN 25448 failure modes and effects analysis ( FMEA ), November 2006 Replaced by DIN EN 60812
DIN 25449 reinforced and prestressed concrete components in nuclear installations - security concept construction DIN 25450 Ultrasonic equipment for manual testing DIN 25453 test method for shielding in nuclear power plants DIN 25455 treatment of radioactively contaminated gases in nuclear power plants with light water rea DIN 25456 Neutronenfluenzmessung Part 1 Determination of the fluence of fast neutrons with activation and fission detectors Part 2 Determination of the fluence of fast neutrons with iron-activation detectors Part 3 Determination of the fluence of fast neutrons with nickel-activation detectors Part 4 Determination of the fluence of fast neutrons with niobium activation detectors Part 5 Determination of the fluence of fast neutrons with copper activation detectors Part 6 Determination of the fluence of fast neutrons with thorium-split detectors DIN 25457 Activity measurement methods for the release of radioactive materials and nuclear facilitie Chapter 1 Basics
Part 4 Contaminated and activated metal scrap Part 6 rubble and buildings Part 7 floor Surfaces DIN 25460 Passive fire protection for hot cells DIN 25462 in situ gamma spectrometry for nuclide environmental contamination measurement DIN 25463 calculation of the decay heat of the nuclear fuel from light water reactors Part 1 Nichtrezyklierte nuclear fuel Part 2 uranium-plutonium mixed oxide (MOX) for pressurized water reactors -Kernbrennstoff DIN 25466 for radioactive - Rules for the design and testing
DIN 25471, taking into account the criticality Brennelementabbrands in the storage and handling of fu nuclear power plants with light water reactors DIN 25472 criticality at the disposal of spent nuclear fuel DIN 25474 administrative measures to comply with the criticality safety in nuclear facility, other than DIN 25475 Nuclear facilities - Operational monitoring Part 1-borne noise monitoring to detect loose parts
Part 2 vibration monitoring for early detection of changes in the vibrational behavior of the primary ci water reactors DIN 25476 primary coolant cleaning systems in nuclear power plants with light water reactors DIN 25478 use of computing systems the assessment of criticality DIN 25480 Part 1 components for contamination protection boxes, Neck, rings for remote handling, windows and DIN 25483 method for environmental monitoring with integrated Festkörperdosimetern
DIN 25485 calculation of the decay heat power in nuclear fuels of high temperature reactors with sph DIN 25488 components for hot cells Part 1 Requirements for the remote control oriented design Part 2 Requirements for radiation resistance, corrosion resistance and ease of decontamination DIN 25489 Determination of uranium and plutonium isotopic composition and the; Mass spectrometric
DIN 25490 Determination of uranium content of uranium hexafluoride nuclear grade, Uranylfluoridlösu nitrate, uranium oxide, uranium dioxide powder and tablets; Gravimetric method DIN 25491 Determination of bulk density and vibration density of nuclear fuel powder
DIN 25492 Determination of uranium content in nuclear fuel; Potentiometric method nach the modifie method
DIN 25493 Nuclear facilities - Protection of metallic component Surfaces from damage by fitting produ packings, packaging material and thermal insulation
DIN 25494 Determination of the density and the proportions of open and closed porosity of uranium d Siedewasserverfahren and penetration buoyancy method DIN 25495 Determination of density and total porosity of uranium dioxide pellets; Mercury displaceme DIN 25496 HVAC components in nuclear plants DIN 25499 Determination of plutonium after oxidation to the hexavalent form; Spectrophotometric me DIN 25525 rail vehicles - Wood Joints DIN 25570/2 tools for rail vehicles - Tubes - overview, selection, application, bending radii
DIN 25700 surface contamination measurements on motor vehicles and Their loads in radiation prote emergency situations DIN 25701 Determination of the solubility of plutonium from unirradiated mixed oxide nuclear fuel in n DIN 25703 Determination of uranium and plutonium content in nitric acid solutions; The wavelength röntgenfluoreszenzspektrometrisches method
DIN 25704 Determination of plutonium content in nitric and sulfuric acid solutions; Potentiometric titra dichromate DIN 25705 Ceramography of sintered nuclear fuel pellets DIN 25706 Passive radon measurements Part 1 Kernspurmeßverfahren Part 2 Aktivkohlemeßverfahren DIN 25707 Determination of oxygen / uranium ratio in uranium dioxide nuclear fuel DIN 25708 Determination of Metallic Impurities in nuclear fuel optical emission with inductively couple DIN 25709 Determination of densification for UO 2 - and UO 2 / Gd 2 O 3 - fuel pellets
DIN 25710 Determination of equivalent hydrogen content in Urandioxidpulvern and pellets of UO 2 , ( Pu) O 2 by the carrier gas method DIN 25711 ?-spectrometric determination of 232 U isotope content in uranium-Containing Solutions of
DIN 25712, taking into account the criticality of the fuel burn During transport and storage of spent lig in containers DIN 26012 tank cars; arrangement of the filling and emptying of petroleum tank cars DIN 26016 tank cars and tank containers; stop-valves with flange, installation and connection dimens
DIN 26017 tank cars and tank containers; stop-valves with thread connection, installation and connec accessories DIN 26029 tank cars; ventilation holes and screw plug Part 1 pressure gas tank cars with bottom discharge Part 2 tank car tank with inclined DIN 26030 Tank wagons and wagons for powdered materials; grounding device DIN 26032 tank cars; Code for hazardous materials; Danger panel mounting frame DIN 26050 Interfaces of tank systems - Petrol station interface Part 1 General requirements and Petrol station Part 2 component pump Part 3 component price transparency Part 4 component tank gauging Part 5 component tankers Electronics Part 6 component fuel terminal
DIN 26053 Trusted measurement technique for tank vehicles for the delivery of heating oil, diesel fue users DIN 26054 corrugated pipes trousers made of non-metallic materials for chemical substances
DIN 26055 hose assemblies for use in the pharmaceutical and biotechnological industry with hoses of materials Part 1 tubes made of PTFE and derivatives Silicone rubber hoses Part 2 Part 3 Elastomeric hoses with or without liner
DIN 26281 Rolling bearings - Dynamic load ratings and rating life calculation of the modified nominal for bearings (ISO / TS 16281: 2008 + Cor 1: 2009) DIN 27000 specifications for bar-coded ID cards in Conjunction with slot readers DIN 27151 rail vehicles - National freight wagons - Requirements DIN 27167 Electrical and Air Technical equipment of rail vehicles; Battery boxes; Main dimensions, des DIN 27170 electrical and climate technical facilities of railway vehicles - Cabinets Part 1 pitch dimensions Part 2 requirements Part 3 Installation notes DIN 27200 State of railway vehicles - Terms and definitions for the reliable state DIN 27201 State of railway vehicles - Basic principles and production technology Part 1 Procedure for preparation and modification of maintenance programs Part 2 Proof of maintenance Part 3 Workshop drive Part 4 Treatment of railway vehicles for dangerous events Part 5 Checking of wheel and wheelset forces of railway vehicles Part 6 welding Part 7-destructive testing Part 9 Measure Part 10 Thermal Spraying Part 11 Procedure for preparation of fault tolerance concept Part 12 fixed to the railway vehicle related systems Requiring monitoring DIN 27202 State of railway vehicles - Vehicle and special equipment Part 1 vehicle body Part 2 draw gear and buffers Part 3 steps, hand rails, handrails, ladders, railings Part 4 vehicle transitions Part 5 Movable components of vehicle bodies and doors (except doors of passenger spaces) Part 6 load securing and transport protection devices Part 7 Conclusions Part 8 cargo containers / tanks Part 9 plants containment substances hazardous to water and container and piping for flammable liqu Part 10 measuring vehicle body DIN 27204 State of railway vehicles - Running gear Part 3 axle box Radsatzlagerführung Part 4 steel suspension Part 5 elastomer suspension Part 6 air suspension Part 7 bogie and accessories Part 8 tilting DIN 27205 State of railway vehicles - Brake
Part 1 block brake, mechanical part Part 2 disc brake, mechanical part Part 3 Ventilated wave brake discs Part 4 Non-vented brake discs wave Part 5 wheel brake Part 6 magnetic brake Simple unfired pressure vessels Part 7 for air Part 8 Tightness and efficiency Part 9 Function of driver's brake valves, actuators and Display to driver Part 10 Function of emergency and emergency brake
Part 11 function and tightness of the brake for direct braking on powered traction unit and indirect bra vehicles Part 12 Function and tightness of the motor vehicle brake in railway vehicles DIN 28000 Chemical apparatus - Documentation in the life cycle of process plants Part 1 Registration of the essential and supplementary documentation Part 2 content of the documentation Part 3 Flow diagrams and plant identification DIN 28004 flow diagrams of process plants Part 1 terms, flow chart types, information content of March 2001 Replaced by DIN EN ISO 10628 Part 2 Graphical version of March 2001 Replaced by DIN EN ISO 10628 Part 3 Graphical symbols of March 2001 Replaced by DIN EN ISO 10628 Part 4 designation, June 2003 Replaced by DIN 6779-13 and DIN EN ISO 10628 DIN 28005 Tolerances for vessels Part 1 container of metallic materials Part 2 containers made of enameled steel, DIN 28006 Tolerances for Reactors Part 1 stirred vessel made of metallic materials Part 2 Reactors enamelled steel, DIN 28007 tolerances for columns Part 1 columns of metallic materials Part 2 columns made of steel, enamelled DIN 28008 tolerances and tolerances for shell and tube heat exchangers DIN 28011 Dished Heads - dished shape DIN 28013 Dished Heads - catenary shape DIN 28015 columns; Soil and packed columns; middle part, for exchange column elements, design dim DIN 28016 columns; Appointments DIN 28017 Permanent Means of access to technical apparatus Part 1 Stages Part 2 Railings for platforms Part 3 ladders Part 4 descent fuses
DIN 28018 pressure vessel steel, enamelled - container for plants 0.063 m 3 to 10 m 3 DIN 28019 pressure vessel steel, enamelled - Tanks for Storing 12.5 m 3 to 125 m 3 DIN 28020 Horizontal Pressure Vessels 0.63 m 3 to 25 m 3 - Dimensions DIN 28021 Stationary pressure vessels - container for storage, 6.3 m 3 to 100 m 3 - Dimensions DIN 28022 Stationary pressure tanks - tanks for process plants 0.063 m 3 to 25 m 3 - Dimensions DIN 28025 connectors made of stainless steel DIN 28030 flange for vessels and equipment Part 1 Apparateflanschverbindungen Part 2 flanges, tolerances DIN 28031 welding flanges for non-pressure vessels and equipment DIN 28032 welding flanges for pressure vessels and apparatus (black), September 2013 Replaced by D DIN 28033 flange connections for equipment - Welding flanges: concerning pressurized equipment DIN 28034 flange connections for equipment - Welding neck: concerning pressurized equipment DIN 28036 welding flanges for pressure vessels and apparatus (White), September 2013 Replaced by
DIN 28038 welding flanges with cyl. Approach for pressure vessels and apparatus (White), September DIN 28033 DIN 28040 flange connections for devices - Gaskets DIN 28058 Lead in apparatus Part 1 Homogeneous lead-lining Part 2 constructions of lead semi-finished products DIN 28070 chemical ovens with liner; Principles for the construction of furnaces DIN 28071 chemical ovens with liner; Principles for the lining DIN 28080 Saddles for horizontal machines DIN 28081 feet apparatus Part 1 of tube - Dimensions Part 2 of profiled steel; Mass Part 3 of tube foot shape B; maximum weight forces of dished Part 4 of profiled steel; maximum moments in the vessel wall Resulting from weight forces apparatus DIN 28082 Skirted for apparatus Part 1 With easy foot ring; Mass Part 2 foot ring with claws and double crown lands; Mass DIN 28083 claws Part 1 dimensions, maximum weight forces Part 2 maximum moments on the vessel wall Resulting from gravitational forces via claws Form A DIN 28084 support rings and ring bearer on equipment Part 1 strength calculation Part 2 versions, dimensions, thickness determination Part 3 Dimensions and weights for maximum operating reactors Non-alloy and stainless steels DIN 28085 trunnions on equipment for installation; Dimensions and maximum forces DIN 28086 eyebolts on equipment for installation; Dimensions and maximum forces DIN 28087 support straps on equipment for installation; Dimensions and maximum forces
DIN 28090 Static gaskets for flanged connections Part 2 Gaskets made ??from sheets; Special test procedures for quality assurance Part 3 Gaskets made ??from sheets; Test method for the determination of chemical resistance DIN 28091 Technical delivery conditions for gasket sheets Part 1 Gasket materials; General requirements Part 2 sealing materials based on fibers (FA); Requirements and testing Part 3 sealing materials based on PTFE (TF); Requirements and testing Part 4 sealing materials based on expanded graphite (GR); Requirements and testing
DIN 28105 chemical apparatus - vessels with two dished ends - definition, nominal volume, nominal d dimensions DIN 28115 connectors made of carbon steel - PN 10 to PN 40 DIN 28117 block flanges for apparatus - Connecting dimensions PN 10 to PN 40 DIN 28120 Round sight glasses with socket in the main load circuit DIN 28121 Circular sight glasses with version in force shunt
DIN 28122 blank flanges with casing of stainless steel for nominal sizes DN 125 to DN 500 and PN-sta DIN 28124 manhole covers Part 1 For non-pressurized container Part 2 For pressure vessels, steel Part 3 For pressure, disguised Part 4 manipulators DIN 28125 snap fasteners Part 1 round; nominal sizes DN 150 to DN 600 Part 2 oval, 350 mm × 450 mm Part 3 round, with protective ring and surface protection; nominal size DN 500 and DN 600 DIN 28127 current funnel for half coils of containers DIN 28128/2 coils for process plant equipment DIN 28130 Chemical Plant - Overview of components of stirred tank with agitator DIN 28131 stirrer and baffles for agitator vessels; forms, terms and main dimensions DIN 28132 agitators, agitator diameter DIN 28134 Chemical apparatus; suspension springs; for clamp couplings for vertical agitator shafts DIN 28135 thrust washers for disc clutches on vertical agitator shafts DIN 28136 Reactors Part 1 Main dimensions Part 2 arrangement and size of the nozzle for agitator vessels made of carbon and stainless steel Part 3 arrangement and size of the nozzle for agitator vessels made of steel enamelled, Part 11 arrangement and size of the cover piece for stirred tank made of steel, enamelled shape with volume; Not for new designs
Part 14 nozzle assembly for H stirred vessel made ??of steel, enameled, shape BE d 1 = 2400 mm to 3 assembly for K Reactors enamelled steel, CE form d 1 = 2400 mm to 3600 mm; Not recommended for DIN 28137 Rührwerkflansche
Part 1 For Reactors made of carbon and stainless steel Part 2 of Form E for agitator vessels made of steel enamelled, DIN 28138 Mechanical seals for agitator shafts Part 1 Made of carbon or stainless steel - operating data, installation dimensions Part 2 Made of steel enamel - operating data, installation dimensions Part 3 valves for sealing fluids, cooling, inspection and assembly and designation system for mechani DIN 28139 stub for enameled equipment Part 1 Form H main flanges for clamp screws; Mass Part 2 of the form M manhole, handhole socket, mounting hole with clamp screws; Connecting dimens Part 3 of Form S neck with split loose flange; Connecting dimensions DIN 28140 connectors for outlet fittings on containers Part 1 Made of carbon steel, stainless steel, and steel lined, Connection dimensions PN 10 Part 2 from steel, enamelled; Connection dimensions PN 10 DIN 28141 mounting flanges for containers and vessels made of carbon and stainless steel DIN 28144 Rührerverbindung for two-part stirrer made of steel, enamelled - Dimensions DIN 28145 Welded enamelled parts for stirred tank made of steel,
Part 1 fixture for baffle type S for container nominal diameter 2400-3600 mm; Connecting dimensions designs Part 3 arrangement and size of eyebolts Part 4 support rings Part 5 Dämmkragen at the bottom outlet Gantry Part 6 Part 8 feet DIN 28146 baffles made of steel, enamelled, for Reactors - Mounting dimensions DIN 28147 thermometer tubes of steel, enamelled, for agitator vessels; installation dimensions DIN 28148 PTFE-coated seals for agitator vessels made of enameled steel, DIN 28150 loose flange, split, for enameled stub; nominal pressure PN 10 DIN 28151 connector for stirred tank shell steel enamel - nozzle assembly DIN 28152 clamp screws for enameled equipment Part 1 degree classification Part 2 Technical delivery conditions DIN 28153 cap for light duty enamelled steel, Part 1 nominal sizes 350 × 450, 500 and 600 Part 2 Diameters from 100 to 250 DIN 28154 shaft end for stirrer made of carbon and stainless steel, for mechanical seals; Mass DIN 28155 connectors for stirrer shafts made ??of carbon and stainless steel; Couplings in the stirred DIN 28156 shaft end for stirrer made of carbon and stainless steel, for stuffing; Mass DIN 28157 impeller, steel, enamelled, one-piece; Mass DIN 28158 anchor, enameled steel, one-piece; Mass DIN 28159 shaft end for one piece of steel stirrer enamel - Dimensions DIN 28160 support rings for agitator vessels made of carbon and stainless steel - Altitude
DIN 28161 requirements stirring drives - speed, direction of rotation storage, concentricity, expansion mechanical seal DIN 28162 Part 1 Rührwerklaternen for stirring drives with mechanical seal DIN 28178 swirl tubes - Dimensions and materials DIN 28179 U-steel tubes for tubular heat exchangers - Technical delivery conditions DIN 28180 Seamless steel tubes for tubular heat exchangers - Dimensions and materials DIN 28181 Welded steel tubes for tubular heat exchangers - Dimensions and materials
DIN 28182 and tube heat exchangers - tube subdivisions, diameter of the holes in tube sheets, Umlen support plates DIN 28183 and tube heat exchangers - Appointments DIN 28184 and tube heat exchanger with two fixed shelves Part 1 inner tube 25, triangular pitch 32 - number and arrangement of the inner tubes Part 2 inner pipe 25 square pitch 32 - number and arrangement of the inner tubes DIN 28185 fittings for tube heat exchangers DIN 28187 and tube heat exchangers - tube / tubesheet attachments DIN 28190 and tube heat exchanger with welded floating head - Examples for tubing and floating hea DIN 28191 and tube heat exchangers with flanged floating head - Examples for tubing and floating he DIN 28192 Elastic bulkhead seals for shell and tube heat exchangers DIN 28400 vacuum technology, designation and definitions Part 1: General terms Part 2 Vacuum Pumps Part 3 vacuum gauges Part 5 vacuum drying and freeze-drying Part 6 analysis technique for surface layers Part 7 vacuum metallurgy Part 8 vacuum systems, components and accessories DIN 28401 Vacuum technology - Symbols - Overview DIN 28403 vacuum technology; quick links; Small flange connections DIN 28404 vacuum technology; Flanges; Mass
DIN 28416 vacuum technology; Calibration of vacuum gauges in the range of 10-3 to 10-7 mbar, Gen pressure reduction through continuous flow DIN 28426 vacuum technology; Acceptance specifications
Part 1 for Rotationsverdrängervakuumpumpen, blocking and rotary vane vacuum pumps and rotary pi medium vacuum range Part 2 for rotary piston vacuum pumps, Roots vacuum pumps in fine vacuum
DIN 28427 vacuum technology; Acceptance specifications for diffusion pump and steam jet vacuum p vapor surrounding pressures <1 mbar DIN 28428 vacuum technology; Acceptance specifications for turbo molecular pumps DIN 28429 vacuum technology, ion getter pumps Acceptance specifications for
DIN 28430 vacuum technology; Meßregeln for steam jet vacuum pumps and steam jet compressors; P vapor
DIN DIN DIN DIN DIN DIN
28431 28432 28460 28461 28462 28463
vacuum technology; acceptance specifications for liquid ring vacuum pumps vacuum technology; Acceptance specifications for diaphragm vacuum pumps Flanges for tank trucks; Welding flanges for aluminum tubes Flanges for tank trucks; Smooth welded steel tubes Flanges for tank trucks, tank truck for threaded couplings Flanges for tankers fittings; Gaskets
DIN 28601 Pipes and fittings made of ductile cast iron - screw-gland joints - Assembly, sockets, screw rings
DIN 28602 Pipes and fittings made of ductile cast iron - bolted-gland joints - Assembly, sockets, stuffin head bolts and nuts DIN 28603 Pipes and fittings made of ductile cast iron - socket joints - Assembly, sockets and seals DIN 28650 fittings made of ductile cast iron - 30 ° bends, EN-pieces, MI pieces, IT equipment - applica DIN 29900 Part 2 Aerospace; Single core cables with aluminum conductor, 600 V, 150 ° C, Technical delivery cond DIN 29921 Aerospace; Screw rivets in steel with hexagonal head and thread lock DIN 29924 Aerospace; Screw rivets in steel with 100 ° countersunk head and thread lock DIN 29963 Aerospace; Expansionsklebfolien for load-bearing parts, technical specifications DIN 29965 Aerospace; carbon fibers; Kohlenstoffilamentgarne; Technical delivery conditions DIN 29970 Aerospace - Honeycomb cores of polyamide paper, phenolic resin bonded - Technical delive DIN 29971 Aerospace; Unidirektionalgelege prepreg of carbon fibers and epoxy resin; Technical delive DIN 29972 Aerospace; Foams; panels; Technical delivery conditions
DIN 29978 Aerospace - Honeycomb cores, hexagonal expanded from aluminum alloy, corrosion-resista or perforated; Technical delivery conditions DIN 29995 Aerospace; Beizscheibenprüfung of remelted steels, nickel and cobalt alloys DIN 30000-39999 [ Edit ] DIN 30052 Name of the wheel arrangement for rail vehicles DIN 30295 Rounded acme thread Part 1 nominal dimensions Part 2 thread limit dimensions and Allowances Permissible Deviations and Permissible Wear of Thread DIN 30386 hex nuts - Rounded acme thread DIN 30387 approach Nuts - Metric thread Rounded acme thread DIN 30389 Hexagon and castle nuts with round thread, turnbuckle and Hitch drivetrains DIN 30630 Technical drawings - General tolerances in mechanical engineering - tolerance rule and Ov DIN 30642 Signs - Vocabulary DIN 30643 Signs - abrasion and smudge resistance of labels on signs - Requirements and testing DIN 30645 Technical delivery conditions for signs Part 1 Anodized Signs (anodising) Part 2 Etched Signs DIN 30646 Self-adhesive labels - Technical delivery conditions for signs of plastic, aluminum foil and p DIN 30650 Odoriermittelbehälter for transport and storage; Safety requirements and testing DIN 30658 material for the subsequent offer sealing of underground gas mains Part 1 movie Sleeving and Fabric Tubing for subsequent offer sealing of gas pipelines; Safety requirem
Part 2 material for the subsequent offer sealing of connections of buried gas lines; Safety requirement DIN 30660 sealant for gas and water supply, and water heating systems - non-hardening sealant and polytetrafluoroethylene (PTFE) tapes for metallic threaded joints in domestic installations DIN 30664 hoses for gas burners for laboratories without casing and armouring Part 1 Safety requirements and tests DIN 30665 gas appliances, gas burners for laboratories (laboratory burners) Part 1 Safety requirements and testing DIN 30670 polyethylene coatings of steel pipes and fittings - Requirements and tests
DIN 30672 organic coatings for the corrosion protection of buried soils and water pipelines for continu Temperatures up to 50 ° C without cathodic protection - Tapes and shrinkable materials DIN 30674 coating for pipes made of ductile cast iron Part 3 zinc coating with topcoat Part 5 polyethylene foil envelope DIN 30675 External corrosion protection of buried pipelines Part 1 protection measures and applications in steel pipelines Part 2 protective measures and areas in pipes made of ductile cast iron DIN 30677 External corrosion protection of buried fittings Part 1 envelope (outer coating) for normal requirements Part 2 envelope of thermosets (outer coating) for Increased requirements DIN 30678 sheath of steel pipes with polypropylene DIN 30690 components in systems of gas supply Part 1 Requirements for components in gas supply systems Part 2 requirements for metallic materials for control valves for gas appliances DIN 30692 membranes for gas distribution and installation Part 2 Requirements and test of reinforced diaphragm material DIN 30693 pant rupture protection for hoses in liquefied petroleum gas systems DIN 30694 gas equipment for LPG in vehicles, cooking, baking, grilling, refrigerators and freezers Part 4 requirements and testing DIN 30695 Portable furnaces with liquefied gas furnaces DIN 30697 LPG-fired portable air heaters with heat exchangers Part 3 Safety requirements, testing, marking DIN 30699 propane / butane gas lamps; Requirements and testing DIN 30701 Municipal vehicles - General requirements DIN 30702 Municipal vehicles Part 5 terms for suction vehicles and high pressure flushers DIN 30704 machines for street cleaning - sweeping, washing vehicles and Combinations thereof DIN 30705 Suction vehicles and high pressure flushers Part 1 channel and gully cleaning vehicles, tanks-Cleaning Vehicles Part 4 high pressure flushers DIN 30706 terms of municipal engineering Part 1 waste DIN 30707 machines for winter maintenance
Part 2 Requirements for winter service vehicles with snow plows Part 3 Specifications for vehicles and equipment DIN 30710 Safety identification of vehicles and equipment DIN 30714 plate brushes for street cleaning vehicles; Mass DIN 30716 roller brush machines for street cleaning and road maintenance services - Dimensions DIN 30720 for container-bucket Part 1 tank with a capacity up to 10 m 3 Part 2 containers having a nominal capacity of 15 m 3 and 20 m 3 DIN 30722 Roller contact tipper, Ro Part 1 Roller contact tipper vehicles up to 26 t, ro system 1570 steel Part 2 Roller contact tipper vehicles up to 32 tons, Ro System 1570 steel Part 3 Roller contact tipper vehicles up to 12 tons, Ro System 900 steel Part 4 Abrollbehälter for transport by road and rail DIN 30723-bucket, Absetzkippeinrichtungen - sizes, requirements DIN 30728 Graphical symbols for communal purposes Part 3 street cleaning vehicles, winter maintenance vehicles Part 4 pit and sewer cleaning vehicles Part 5 Attachments with boom DIN 30730 Mobile compactors --bucket and Roller contact tipper; requirements, connection dimension
DIN 30734 unicameral exchange silo (free-fall) for dry bulk sedimentation and roll-off vehicles - conne requirements DIN 30735 containers with a maximum width of 1520mm for bucket system - Dimensions, material, d
DIN 30737 waste containers - Mobile discharge system containers with hinged lid and a volume of 2.5 beds with lid opening device DIN 30739 containers for infectious waste with a capacity of 30 l to 60 l DIN 30741 waste containers Part 1 bins for hazardous waste with a volume of 800 l for solid hazardous waste Part 2 bins for hazardous waste with a volume of 1000 l for liquid hazardous waste DIN 30742 Waste disposal technology - Waste containers for liquid and solid hazardous waste Part 1 container with a volume of 60 l to 240 l of metallic materials
DIN 30743 Waste disposal technology - help with loading the storage and transport of waste containe waste
DIN 30745 Electronic identification of waste containers by transponder technology using frequencies b in German and English DIN 30760 Mobile waste containers - Waste containers with two wheels and a nominal capacity of 60 diamond lifting DIN 30781 transport chain Part 1 Basic Concepts Part 2 classification of transport and transport routes DIN 30783 Modular order in the transport chain; Dimensional Coordination in the horizontal Part 1 Definitions, principles DIN 30784 transport chain; transport chain for money and values
Part 1 Dimensional Coordinates Part 2 cassettes; Dimensions and requirements for stackability Part 3 magazines for ATMs, coordination degree requirements for interfaces DIN 30786 Transportation loads - Data collection of dynamic mechanical loads Part 1: General principles and overview of the standard structure Part 2 values ??collections DIN 30791 transport chain; Ticket Part 2 terms DIN 30795 Information on public transport
Part 1 Information for the sale of tickets - General requirements for the arrangement and design of inf controls
Part 2 information for the sale of tickets from stationary machines with selection buttons - arrangeme information and controls
Part 3 Information for the sale of tickets from stationary machines with numeric keypad - arrangemen information and controls
Part 4 information for the ticket sales from mobile machines with selection buttons - arrangement and information and controls
Part 5 Information on the sale of tokens for time tickets from stationary terminals - arrangement and l and controls
Part 6 Prior information at stops on the sale of tickets by the driver - the layout and design of the infor Part 7 information for the sale of tickets of interoperable machine, arrangement and layout of informa DIN 30800 transport chain; handling equipment in the transport chain Part 1 transport chains for bulk rail transport; Descriptions and join criteria Part 2 Assignment of bulk materials and bulk freight wagons Part 3 handling procedures and interfaces in bulk rail transport; Assignment of terminals and bulk Car
DIN 30801 handling equipment in the transportation chain - Loading of bulk freight wagons - Interface loading equipment DIN 30802 handling equipment in the transportation chain - Unloading of Bulk Car Part 1 interfaces wagons / unloading Part 2 interfaces Trichterseitenentladewagen / unloading Part 3 interfaces Trichtermittenentladewagen / unloading DIN 30803 handling equipment in the transportation chain - Defrosting / antifreeze protection for hopp
DIN 30823 Bulk containers - Rigid IBC - Metal, rigid plastics and composite IBCs; Dimensions, design r labeling, DIN 30910 Sintermetalle - material data sheets (WLB) Part 1 Notes on the WLB Part 2 sintered metal filter for Part 3 sintered metals for bearings and parts with sliding properties Part 4 sintered metals for molded parts Part 6 sinter forging steels for Molding DIN 30911 Sintered metals; Sint-test standards (SPN) Part 0 Notes to the SPN
Part 6 Examination of the filter characteristics Part 7 examination of the soft magnetic properties DIN 30912 Sintered metals; Sint guidelines (SR) Part 1 Mechanical machining of sintered parts DIN 30950 melting hardening - General Process Description DIN 30960 melting hardening with additional materials - Schmelzhärtungs statement (SHA) - form DIN 30965 Laser Technology - Laser Härtbarkeitsversuch
DIN 30999 hard metals - Rockwell hardness test (scales A and 45N) - Calibration of reference blocks o testing and calibration of hardness testing machines DIN 31000 (VDE 1000: 2011-05) General principles for the safe design of products DIN 31001 Safety-oriented design of technical products; Protective devices; Terms Part 1 safety distances for adults and children, March 2009 Replaced by DIN EN ISO 13857 DIN 31051 Fundamentals of Maintenance DIN 31216 Spring Fastener Part 2 parts and friction plates DIN 31300 Graphical symbols for watches DIN 31302 clocks, pendulum rods DIN 31623 for indexing the contents of documents Part 1 Definitions, principles Part 2 DC marshaling indexing with descriptors Part 3 Syntactic indexing with descriptors DIN 31625 Extended character set for African languages DIN 31628 Bibliographic character sets; Character set levels for the data input DIN 31630 registers creation Part 1 terms, formal design of printed registers DIN 31631 Category catalog for documents Part 1 Concepts and presentation Part 2 Systematic part Part 3 indicator for processing control of categories Part 4 codes for entries to categories of data Part 5 treatment of data categories with an entry or multiple entries in data formats Part 6 Category catalog for the description of institutions Part 7 Category catalog for the description of projects DIN 31634 Information and documentation - Romanization of the Greek alphabet DIN 31635 Information and documentation Urdu and Pashto DIN 31636 Information and documentation DIN 31638 Bibliographic order rules DIN 31644 Information and documentation DIN 31645 Information and documentation
- Romanization of Arabic alphabet for Arabic, Ottoman Turk - Conversion of the Hebrew alphabet
- Criteria for Trusted Digital Repositories - Guidelines for the transfer of information in digital reposi
DIN 31646 Information and documentation - Requirements for the long-term management of persiste (Persistent Identifier)
DIN 31651 plain bearings Part 1 symbols, classification Part 2 icon, application DIN 31653 plain bearings, thrust bearings in stationary hydrodynamic operational Part 1 Calculation of Axialsegmentlagern Part 2 functions for the calculation of Axialsegmentlagern Part 3 Operation Guide values ??for the calculation of Axialsegmentlagern DIN 31654 plain bearings, thrust bearings in stationary hydrodynamic operational Part 1 Calculation of axial tilting pad bearings Part 2 functions for the calculation of axial tilting pad bearings Part 3 Operation Guide values ??for the calculation of axial tilting pad bearings DIN 31655 plain bearings, journal bearings Hydrostatic plain in stationary operational Part 1 Calculation of oil-lubricated plain bearings without intermediate grooves Part 2 parameters for the calculation of oil-lubricated plain bearings without intermediate grooves DIN 31656 plain bearings, journal bearings Hydrostatic plain in stationary operational Part 1 Calculation of oil-lubricated bearings with intermediate grooves Part 2 parameters for the calculation of oil-lubricated bearings with intermediate grooves DIN 31657 Plain bearings - Hydrodynamic plain journal bearings in stationary operational Part 1 Calculation of multi-surface and tilting pad bearings Part 2 functions for the calculation of multi-surface bearings Chapter 3 Functions for calculation of tilting pad bearings Part 4 operating guideline for the calculation of multi-surface and tilting pad bearings DIN 31661 plain bearings, Terms, characteristics and causes of changes and damages
DIN 31665 plain bearings; Testing of bearing metals; Corrosion resistance of bearing metals by lubrica conditions DIN 31670 plain bearings; Quality assurance of bearings Part 8 Examination of geometrical Deviations and surface roughness on shafts, collars and trace slices DIN 31690 plain bearings, plain bearings Housing; Plummer DIN 31691 oil level; requirements, connection dimensions, ports DIN 31692 plain bearings Part 1 lubrication and lubrication monitoring Part 2 Temperature Monitoring Part 3 vibration monitoring Part 4 Electrical isolation bearings Part 5 Checklist for checking the oil leaks DIN 31693 plain bearings, plain bearings Housing; Seitenflanschlager DIN 31694 plain bearings, plain bearings Housing; Mittenflanschlager DIN 31696 plane thrust bearing, thrust bearings segment, mounting dimensions DIN 31697 plane thrust bearing, thrust ring bearings, mounting dimensions DIN 31698 plain bearings; Fits DIN 31699 plain bearings, Waves, collars, track wheels; Shape and position tolerances and surface rou
DIN 32503 Protective caps for operating pressure gauges (gauge) with case diameter 63 mm, for weld allied Processes DIN 32506 solderability for soldering Part 1 wetting tests Part 2 Hubtauchprüfung for samples of copper alloys; Testing assessment Part 3 Hubtauchprüfung for tin samples; Testing assessment
DIN 32508 micro-soldering and -Schweißgeräte own hydrogen / oxygen generation - Mechanical and g requirements, testing, marking DIN 32509 Manually operated valves for welding, cutting and allied Processes - Types, safety requirem
DIN 32510 Thermal cutting - Burning drilling with oxygen lances in mineral materials - Methods basics minimum equipment DIN 32511 Welding - electron beam process for material treatment - Terms for Processes and equipme DIN 32513 soft solder pastes Part 1 composition, technical specifications DIN 32516 Thermal cutting - cutting thermal properties of metallic components - General principles an DIN 32520 Graphical symbols for welding Part 1 General symbols, foundations Part 3 Graphical symbols for fusion welding arc DIN 32525 Welding consumables - Testing of welding consumables by Means of weld Part 4 test piece for deterministic mining the hardness of surfacing DIN 32527 Heating for welding, brazing, cutting and allied Processes - Definitions, Processes DIN 32532 welding - laser method for material processing - terms for Processes and devices
DIN 32533 Welding - electron beam process for material processing - beam parameter product - Meas focus diameter and angle of divergence DIN 32535 ??Thermal spraying - Schichtzugversuch DIN 32539 Flame cleaning of steel and concrete Surfaces DIN 32540 laser ablation - Thermal removing with laser beam - Definitions, influence factors, procedu DIN 32561 Production equipment for microsystems - Tray - Dimensions and tolerances DIN 32563 Production equipment for microsystems - Classification system for micro-components DIN 32564 manufacturing equipment for microsystems - Vocabulary Part 1 General terms of micro system technology Part 2 basic technologies and production Part 3 handling, storage and transport DIN 32566 Production equipment for microsystems - specification of a mask support ring for deep X-ra DIN 32605 cuticle scissors, curved, Dimensions, materials DIN 32606 nail scissors, curved, Dimensions, materials DIN 32607 Embroidery scissors; Dimensions, material DIN 32608 Household scissors; Dimensions, materials DIN 32609 Pocket Scissors, Dimensions, material DIN 32611 hair scissors, Dimensions, material DIN 32612 tailor scissors, Dimensions, material DIN 32613 scissors; Appointments
DIN DIN DIN DIN
32619 32620 32622 32623
Smoking trolleys; Terms of quality and safety requirements hose clamp; Tensioner and belt aquarium glass - Safety requirements and testing Hospital Cots metal and plastics - Safety requirements and testing
DIN 32625 Quantities and units in chemistry; Amount of substance and derived quantities, April 2006 without replacement DIN 32629 fabric portions; term, marking; February, 2004 WITHDRAWN without replacement DIN 32633 Chemical analysis - method of standard additions - methods, evaluation, with CD-ROM DIN 32635 Spectrophotometric analysis of solutions, terms, symbols, units DIN 32640 Chemical elements and simple inorganic compounds; April 2008 WITHDRAWN without repl DIN 32641 Chemical formulas; April 2006 WITHDRAWN without replacement DIN 32642 Symbolic description of chemical reactions
DIN 32645 Chemical analysis - limit, detection and quantitation limit under repeatability conditions - T evaluation
DIN 32646 Chemical analysis - detection and quantification limit as performance characteristics - dete collaborative trial under control conditions, terms, meaning Procedure DIN 32649 Graphical symbols for operations in the laboratory; Basic operations DIN 32650 Analysis schedules; Graphical Representation
DIN 32676 Fittings for food, chemical and pharmaceutical industry - Clamp connections for stainless s for butt welding DIN 32677 beverage dispensing systems - wiring connection parts for beverage dispensing system DIN 32705 classification systems; Creation and development of classification systems DIN 32706 Information and documentation - Romanization of the Armenian alphabet DIN 32707 Information and documentation - Romanization of the Georgian alphabet DIN 32711 polygonal profiles P3G DIN 32712 polygon profile P4C DIN 32732 Mechanically operated combustion air flaps; Safety requirements, testing and marking DIN 32736 Property Management - Concepts and Services DIN 32742 and office systems - fax Part 2 Basic requirements Part 3 minimum information DIN 32744 and office systems - magnetic stripe on savings accounts Part 1 Mechanical and electromagnetic properties and Their examination Part 2 position and recording DIN 32745 and office systems; letter opening equipment; minimum information DIN 32747 system for Further Processing of mail and data processing documents - inserters Part 1 Definitions and classification Part 2 minimum information DIN 32749 and office systems, Letter Folders, minimum information DIN 32750 and office systems; Magnetic tape cassettes for voice recorders with magnetic tape 4 Part 1 cassette for winding drive; Dimensions and properties Part 2 cassette for Tonwellenantrieb; Dimensions and properties
DIN 32752 and office systems - Testing of ribbons Part 1 Preparation of standard imprints A and measurement of specular Part 2 General tests Part 3: Preparation of standard imprints B and determination of color transfer and correction capability DIN 32755 and office systems; Ribbons Part 1 coil with 30 mm and 35 mm diameter for ribbons of 13 mm width Part 2 coils with 40 mm and 54 mm diameter for ink ribbons of 13 mm and 14.3 mm width Part 3 coil with 82 mm diameter for writing tapes of 13 mm width DIN 32756 and office systems - correction tapes, cores, bobbins - Definitions, dimensions, designs DIN 32757 and office systems - destruction of information carriers Part 2 machines and equipment - Minimum information DIN 32758 and office systems; Calculating machines; Keyboard for electronic calculators DIN 32780 Protective clothing
Part 100 Protection against electromagnetic fields in the frequency range 80 MHz to 1 GHz; Requireme methods DIN 32781 Protective clothing - Protective suits against pesticides DIN 32786 Bank documents; Magnetic stripe on savings accounts, the structure and content of the ma DIN 32835 Technical product documentation - Facility Management Part 1 Definitions and Methodology Part 2 usage documentation DIN 32869 Technical product documentation - Three-dimensional CAD models Part 1 requirements for the presentation Part 3 functional elements DIN 32876 examination of geometrical parameters - Electrical length measurement Part 1 Analog Input the Measured quantity; Definitions, requirements, testing Chapter 2 digital recording of the Measured quantity; Definitions, requirements, testing DIN 32877 Optoelectronic distance, profile and shape measurement
DIN 32878 Drehwinkelmeßsysteme with memory and incremental acquisition of the Measured quantit requirements, testing DIN 32891 round steel chains - grade 2, non-calibrated tested, DIN 32895 round steel chains for loading wagons and manure spreaders, calibrated tested, DIN 32896 chain links for wagons and manure spreaders DIN 32911 Graphic symbols and signs to inform passengers of cable cars and ski lifts DIN 32912 Graphic symbols and signs for information of skiers on ski slopes DIN 32913 trails; Classification, basic graphic symbols and signs to inform cross-country skiers DIN 32914 signs for lifts, slopes and trails; Requirements
DIN 32932 home fitness equipment, pedal crank training equipment; Concepts safety requirements, t 1997 is Replaced by DIN EN 957-5
DIN 32935 home fitness equipment, non-stationary tension and compression-training equipment; Safe testing DIN 32937 measurement and test equipment - plan, manage and deploy measurement and test equip DIN 32974 Acoustic signals in public areas - Requirements
DIN 32975 Designing visual information in the public domain for accessible use DIN 32976 Braille - Requirements and Measurements DIN 32977 disability-oriented design Part 1 Terminology and general principles DIN 32980 Assignment of the 8-dot Braille font for 7-bit code DIN 32981 additional devices for the visually impaired to road traffic facilities (SVA) DIN 32982 8-dot Braille for information processing - identifiers, names and assignment to the 8-bit co
DIN 32983 Vehicle-lifting devices for wheelchairs and other mobility impaired persons - Additional safe testing DIN 32984 soil indicators in the public transport DIN 32985 Vehicle Ramps for wheelchair users and mobility impaired people - Safety requirements an DIN 33402 Human body measurements Part 1 Definitions, measurement methods Part 2 ergonomics Part 3 of motion at different basic postures and movements DIN 33403 climategate in the workplace and in the work environment Part 2 Influence of climate on the heat balance of the human Part 3 Assessment of the climate in the warm and hot working areas based on selected climate indice Part 5 Ergonomic design of cold workplaces DIN 33404 Danger signals for workplaces Part 3 Auditory danger signals; Unified emergency; Safety requirements and testing DIN 33406 workplace dimensions in the production area - definition, types of employment, workplace DIN 33407 Work Analysis - Features DIN 33408 body outline template for seating Part 1 For seats Supplement 1 Application Examples DIN 33409 Safety Fair labor organization - hand signals for marshalling DIN 33411 body forces of man Part 1 terms, contexts determinants Part 3 maximum achievable static moments of action of male working people on hand wheels Part 4 maximum static action forces (Isodynen) Part 5 maximum static action forces, values DIN 33414 Ergonomic design of Waiting Part 4 classification scheme, arrangement principles DIN 33415 assembly-line work - definition, characteristics DIN 33416 Graphical representation of the human figure in typical postures DIN 33417 Description of location, position and direction of movement of objects DIN 33419 General principles of ergonomic testing of product designs and industrial products DIN 33430 requirements for procedures and Their use in vocational proficiency assessments DIN 33450 Graphical symbol for observation with regard to opto-electronic devices (video Info charact DIN 33466 Guide for trails
DIN 33821 safety relief for gas supply systems with operating surrounding pressures up to 100 bar
DIN 33822 gas pressure regulators and safety devices of the gas installation for inlet surrounding pres DIN 33830 heat pumps; Ready to connect heating absorption heat pumps Part 1 Definitions, requirements, testing, marking Part 3 Cryogenic Safety, testing Part 4 performance testing DIN 33831 heat pumps; Ready to connect heating heat pumps with internal combustion engine-driven Part 1 Definitions, requirements, testing, marking Part 2 Requirements for gas equipment and testing Part 3 performance and Funktionsprüfbedingungen Part 4 performance testing of air / water heat pumps DIN 33852 and office systems - Correction Tapes Part 1 refreshingly different deletion; Dimensions, classification, requirements, testing Part 2 covering deletion, Dimensions, requirements, testing DIN DIN DIN DIN
33858 33859 33865 33866
and office systems; Deleting sensitive data stored on magnetic media; Extinguishers, requ and office systems - Identification cards - National numbering system, registry and applica Information Technology - Plotters - Evaluating the throughput of monochrome plotter Information technology - Text and office systems; A color display devices
Part 1 Method of Specifying image reproduction of color devices with digital and analog test charts; Cl foundations Part 2 Method of Specifying image reproduction of color devices with analog input and analog output display devices: "analog-analog" (copier), design and application
Part 3 Method of Specifying image reproduction with digital input and analog output as a hard copy in reproduction devices: "digital - analog" (printer); Design and application
Part 4 Method of Specifying image reproduction of color devices with analog input and digital output f reproduction devices: "analog-digital" (scanner), design and application
Part 5 Method of Specifying image reproduction of color devices with digital input and analog output a image reproduction devices: "digital-analog" (monitors), design and application
DIN 33868 Information technology - Office equipment - office machines; minimum information in data class 1 and class 2 (ISO / IEC 11160-1: 1996, modified)
DIN 33869 Information technology - Office equipment - office machines; minimum information in data class 3 and class 4 (ISO / IEC 11160-2: 1996, modified) DIN 33870 Remanufactured Toner Cartridges DIN 33871 Information technology - Office machines, inkjet print heads and ink tanks for inkjet printer Part 1 Preparation of refilled inkjet print heads and ink tanks for inkjet printers Part 2 requirements and characteristics of compatible ink cartridges (4-color system) for inkjet printer DIN 33872 Information technology - Office machines - Method of Specifying color reproduction with YE Part 1 Classification, terms and principles on CD-ROM Part 2 Test charts for output properties - testing of distinctness of 5 and 16 step color series, only on C DIN 34820 Plain washers with chamfers for steel construction DIN 34821 screws with internal serration with thread to head
DIN DIN DIN DIN DIN DIN DIN DIN DIN
34822 with flange screws with internal serration with thread to head 34823 oval head with internal serration 34824 Innenvielzahn for screws 34827 screws with hexagon socket 34828 welding ends for turnbuckles 37080-operated controls for brake pads; Overview and arrangement 37081-operated controls for brake pads, support, spring plate 37082-operated controls for brake pads; Compression spring, spring pin 38030 rail vehicles - Compressed air equipment for rail vehicles - Pressure Gauges
DIN 38402 German standard methods for examination of water, waste water and sludge - General info Part 1 Details of analysis results (A 1) Part Part Part Part Part Part Part Part Part Part Part Part Part
6 Determination of minimum frequency of monitoring for water Constituents in discharges (emiss 11 samples of wastewater (A 11) 12 sampling from standing waters (A 12) 13 sampling from aquifers (A 13) 15 samples from streams (A 15) 16 sampling of sea water (A 16) 18 samples of water from mineral and thermal springs (A 18) 20 samples from tidal waters (A 20) 24 Guidance on sampling of suspended solids (A 24) 30 pre-treatment, homogenization and division of heterogeneous water samples (A 30) 41 proficiency testing, planning and organization (A 41) 42 testing methods for process validation, evaluation (A 42) 45 testing methods for the external quality control of laboratories (A 45)
Part 51 calibration of analytical methods, evaluation of analytical results and linear calibration functio determination of performance characteristics (A 51) Part 60 Analytical Quality Assurance for the chemical and physico-chemical water analysis (A 60)
Part 71 equivalence of two analytical methods based on the comparison of analytical results and Thei Procedure for quantitative traits with continuous spectrum of values ??(A 71)
DIN 38404 German standard methods for examination of water, waste water and sludge - Physical an parameters (group C) Part 3 Determination of absorption in the range of UV-radiation, Spectral absorption coefficient (C 3) Part 4 Determination of the temperature (C 4) Part 6 Determination of the redox potential (C 6) Part 10 Calculation of calcite saturation of water (C 10) Part 13 Determination of tritium (C 13)
Part 14 Determination of total alpha activity concentration alpha alpha in drinking water, ground wate (C14)
Part 15 Determination of residual beta activity concentration (C A, Rfi ) in drinking water, ground wate wastewater (C 15)
Part 16 Determination of radionuclides in drinking water, ground water, surface water and wastewater spectrometry (C16)
Part 18 Determination of radium-226 activity concentration in drinking water, ground water, surface w (C 18) DIN 38405 German standard methods for examination of water, waste water and sludge; anions (grou Part 1 Determination of the chloride ions (D 1) Part 4 Determination of fluoride (D 4) Part 5 Determination of sulfate ions (D5) Part 7 Determination of cyanides in low polluted water by ion chromatography or potentiometric titrat Part 9 Photometric determination of nitrate (D 9) Part 13 Determination of cyanides (D 13) Part 17 Determination of borate ions (D 17) Part 21 Photometric determination of Dissolved silica (D 21) Part 23 Determination of selenium by atomic absorption spectrometry (AAS) (D 23) Section 24 Photometric determination of chromium (VI) by 1.5-Diphenylcarbazide (D 24) Section 26 Photometric determination of Dissolved sulfide (D 26) Part 27 Determination of sulfide released Easily (D 27) Section 29 Photometric determination of nitrate with sulfosalicylic acid (D 29), ISO 7890-3: 1988, mod Part 32 Determination of antimony by atomic absorption spectrometry (D 32) Part 33 Determination of iodide by photometry (D 33) Part 35 Determination of arsenic - Method using graphite furnace atomic absorption spectrometry (GF DIN 38406 German standard methods for examination of water, waste water and sludge; cations (grou Part 1 Determination of iron (E 1) Part 2 Determination of manganese (E 2) Part 3 Determination of calcium and magnesium, Complexometric method (E 3) Part 5 Determination of ammonium-nitrogen (E 5) Part 6 Determination of lead by atomic absorption spectrometry (AAS) (E 6) Part 7 Determination of copper by atomic absorption spectrometry (AAS) (E 7) Part 8 Determination of zinc - Method using atomic absorption spectrometry (AAS) using acetylene fla Part 11 Determination of nickel by atomic absorption spectrometry (AAS) (E 11) Part 13 Determination of potassium by atomic absorption spectrometry (AAS) using acetylene flame t Part 14 Determination of sodium by atomic absorption spectrometry (AAS) using acetylene flame to-a Part 16 Determination of 7 metals (zinc, cadmium, lead, copper, thallium, nickel, cobalt) by voltamme Part Part Part Part Part
17 18 21 24 26
Determination Determination Determination Determination Determination
of of of of of
uranium - Method using adsorptive stripping voltammetry in basic, raw and d Dissolved silver by atomic absorption spectrometry in a graphite furnace (E 1 heavy metals nine (Ag, Bi, Cd, Co, Cu, Ni, Pb, Tl, Zn) after enrichment by ext cobalt by atomic absorption spectrometry (AAS) (E 24) thallium by atomic absorption spectrometry (AAS) in a graphite furnace (E 2
DIN 38407 German standard methods for examination of water, waste water and sludge; Together det (group F) Gas chromatographic determination Part 2 of low volatile halogenated hydrocarbons (F 2)
Gas chromatographic determination Part 3 of polychlorinated biphenyls (F 3)
Part 7 determination of 6 polycyclic aromatic hydrocarbons (PAH) in drinking and mineral water by hig layer chromatography (HPTLC) (F 7) Part 8 determination of 6 polycyclic aromatic hydrocarbons (PAH) in water by high performance liquid (HPLC) with fluorescence detection (F 8) Part 9 Determination of benzene and some derivatives by gas chromatography (F 9)
Part 11 Determination of selected organic plant treatment agents by Automated Multiple Developmen (11 F)
Part 14 Determination of phenoxy by gas chromatography and mass spectrometry after solid-liquid ex derivatization (F 14) Part 16 Determination of aniline derivatives by gas chromatography (F 16) Part 17 Determination of selected nitroaromatic compounds by gas chromatography (F 17)
Part 22 Determination of glyphosate and aminomethyl phosphonic acid (AMPA) in water by high-perfo chromatography (HPLC), post-column derivatization and fluorescence detection (F 22)
Part 27 Determination of selected phenols in groundwater and seepage water, Aqueous extracts and p
Part 30 Determination of trihalomethanes (THM) in swimming pool water using headspace gas chroma
Part 34 etermination selected plant treatment agents, biocides and degradation products; Method usi chromatography (GC-MS) after solid-phase microextraction (SPME) (F 34)
Part 35 Determination of selected phenoxy acid plant and Further treatment agents - Method using hi liquid chromatography and mass spectrometry (HPLC-MS / MS) (F 35)
Part 39 Determination of selected polycyclic aromatic hydrocarbons (PAH) - Method using gas chroma spectrometric detection (GC-MS) (F 39)
Part 41 Determination of selected volatile organic compounds in water - Method using gas chromatog spectrometry (GC-MS) by headspace solid-phase microextraction (HS-SPME) (F 41)
Part 42 Determination of selected polyfluorinated compounds (PFCs) in water - Method using high per chromatography and mass spectrometry (HPLC-MS / MS) after solid-liquid extraction (F 42)
DIN 38408 German standard methods for examination of water, waste water and sludge - Gaseous co Part 3 Determination of ozone (G 3) Part 5 Determination of chlorine dioxide (G 5)
DIN 38409 German standard methods for examination of water, waste water and sludge; Summary of substances (group H) Part 1 Determination of total dry residue filtrate, and residue on ignition (H 1) Part 2 Determination of filterable matter and the residue on ignition (H 2) Part 6 hardness of water (H 6) Part 7 Determination of the acid and base capacity (H 7) Part 9 Determination of the volume fraction of settleable solids in water (H 9) Part 10 Determination of the mass concentration of settleable solids in water (H 10) Part 15 Determination of hydrogen peroxide (hydrogen peroxide) and its Adducts (H 15) Part 16 Determination of phenol index (H 16) Part 20 Determination of disulphine-active substances (H 20)
Part 22 Determination of Dissolved adsorbable organically bound halogens in very saline water by sol (SPE-AOX) (H22) Part 23 Determination of bismuth substances (H23) Part 26 Determination of bismuth Komplexierungsindex I BiK (H26) Part 41 Determination of Chemical Oxygen Demand (COD) in the range above 15 mg / l (H 41) Part 44 Determination of Chemical Oxygen Demand (COD) in the range 5 to 50 mg / l (H 44) Part 46 Determination of purgeable organic carbon (POC) (H 46) Part 56 Gravimetric determination of volatile lipophilic substances by solvent extraction (H 56)
DIN 38412 German standard methods for examination of water, waste water and sludge - Method with Part 3 toxicity test to deterministic mine the Dehydrogenasenaktivitätshemmung in activated sludge ( Part 11 Determination of the effect of water on small crustaceans Constituents (Daphnia short-term te
Part 13 Determination of oxygen production and oxygen consumption in the water with the SPG and S method (L 13) (biogenic aeration rate)
Part 14 Determination of oxygen production with the light-dark bottle method under laboratory condit (oxygen production potential) Part 16 Determination of chlorophyll-a content of surface water (L 16) Part 26 degradation and elimination test for surfactants to simulate municipal sewage treatment plan Part 27 Determination of the inhibitory effect of sewage on the oxygen consumption of Pseudomonas (Pseudomonas Sauerstoffverbrauchshemmtest) (L 27) Part 30 Determination of acute toxicity of non-wastewater to daphnia dilution series (L 30)
Part 33 Determination of the non-toxicity of waste water tolerance of green algae (Scenedesmus chlor test) dilution series (L 33)
Part 37 Determination of the inhibitory effect of water on the growth of bacteria (Photobacterium phos Multiplication Inhibition Test) (L 37)
DIN 38413 German standard methods for examination of water, waste water and sludge; individual co Part 1 Definition of hydrazine (P 1) Part 2 Determination of vinyl chloride (chloroethene) by gas chromatographic headspace analysis (P 2 Part 4 Determination of carbon disulfide (P 4)
Part 6 Determination of acrylamide - Method using high performance liquid chromatography and mass (HPLC-MS / MS) (P 6)
Part 8 Determination of Dissolved chelating nitrilotriacetic acid (NTA), ethylenediaminetetraacetic acid Diethylentrinitrilopentaessigsäure (DTPA) with liquid chromatography (LC) (P 8) DIN 38414 German standard methods for examination of water, waste water and sludge; Sludge and Part 4 Determination of leachability by water (S 4) Part 6 Determination of the oxygen consumption rate (S 6) Part 8 Determination of anaerobic digestion (S 8) Part 9 Determination of Chemical Oxygen Demand (COD) (S 9) Part 11 Sampling of sediments (S 11) Part 12 Determination of phosphorus in sludge and sediments (S 12) Part 13 detection of Salmonella in decontaminated sludge (S 13)
Part 14 Determination of selected polyfluorinated compounds (PFCs) in sludge, compost and soil - Met performance liquid chromatography and mass spectrometry (HPLC-MS / MS) (S 14) Part 15 Determination of the specific residual beta activity a R? in mud, sediment and suspended mat Part 17 Determination of extractable organically bound strippable and halogens (S 17) Part 18 Determination of adsorbed organically bound halogens (AOX) (S 18) Part 19 Determination of steam-volatile organic acids (S 19) Determination of 6 polychlorinated biphenyls part 20 (PCB) (S 20)
Determination part 21 of 6 polycyclic aromatic hydrocarbons (PAHs) by Means of high performance liq (HPLC) and fluorescence detection (S 21) Part 22 Determination of freeze-residue and production of freeze mass of sludge (S 22)
Determination part 23 of 15 polycyclic aromatic hydrocarbons (PAH) by high performance liquid chrom and fluorescence detection (S 23) Part 24 Determination of polychlorinated dibenzodioxins (PCDDs) and polychlorinated dibenzofuran (P Part 35 Determination of arsenic - Method using graphite furnace atomic absorption spectrometry (GF DIN 40000-49999 [ Edit ]
DIN 40015 frequency ranges and wavelength ranges DIN 40020 terms of wave propagation DIN 40030 rated Voltages fed DC motor via controllable power converter with direct mains connection DIN 40041 reliability; Terms DIN 40081 guidelines for reliability Part 11 electronic components, lot by lot and periodic inspections DIN 40101 symbols DIN 40103 Electrical properties elongated conductor DIN 40108 Power Systems (concepts, quantities, symbols) DIN 40110 AC quantities Part 1 Two-wire circuits Part 2 multi-wire circuits DIN 40146 terms of message transmission DIN 40148 gain , Level DIN 40150 terms to the order of functional and structural components DIN 40200 par value, design and value. Ä. DIN 40400 electric thread E-threaded, Edison screw z. B. for light bulbs DIN 40401 Thread gauges for electric thread D fuses Part 1 thread ring gauges Part 2 Thread Plug Gauges and Thread Gutlehrenkörper DIN 40430 PG threaded conduit threads DIN 40431 Steel conduit thread Part 1 thread gauges, thread ring gauges and ring gauges Committee Part 2 thread gages, thread plug gauges and Gutlehrdorne DIN 40432 set Taps - Two-piece set for steel conduit thread Pg 7 to Pg 48
DIN 40433 machine tap with Reduced shank (overflow drills) for steel conduit thread Pg 7 to Pg 48 DIN 40434 Round steel conduit for this thread Pg 7 to Pg 48
DIN 40435 Machine taps for tapped holes (EG) for wire thread inserts for ISO metric thread nach DIN 8 Recording threads EC M2 to M52 EC and recording fine threads EC M8 × 1 to EC M48 x 3 - Dimensions DIN 40501 aluminum for electrical engineering Part 2 tubes, rods and profiles, technical specifications
DIN 40540 lead-acid batteries - Traction batteries 24 V, 48 V, 80 V with cells nach DIN EN 60254-2 for Potentially explosive atmospheres for use in (Group II, Category 2 and Category 3) - Dimensions, weig DIN 40603 laminate products, sheets and strip of synthetic resin laminated wood DIN 40604 vulcanised fiber Part 1 plates, sheets, strip, foil Part 2 tubes and rods DIN 40612 Mica products for electrical engineering, sheets, strips, Dimensions DIN 40613 Mica products for electrical engineering; Insulating discs for commutators, dimensions Part 2 form parts for commutators gap mica mica, dimensions DIN 40614 Mica products for electrical engineering; Wide lanes and bands Dimensions DIN 40618 laminate products; Molded flat tubes made ??of laminated paper or hard tissue DIN 40680 Ceramic parts for electrical engineering Part 1 General tolerances for dimensions Part 2 General tolerances for form DIN 40686 Surfaces of ceramic parts for electrical engineering Part 1 General Part 4 Testing of solderable metal pads Part 5 Examination of brazeable metal pads Part 6 high and low voltage insulators Part 7 insulating parts DIN 40705 high-voltage switchgear; Colours of exposed cables, electrical Supplement high voltage switchgear; Colours of exposed cables, electrical DIN 40719 Circuit documents Part 1 Definitions, classification, May 1995 Replaced by DIN EN 61082-1 ??and -3 Part 2 Marking of electrical equipment, december 2000 replaces by DIN EN 61346-1 and -2 Part Part Part Part Part Part Part Part Part
2 Bbl.1 marking of electrical equipment, Alphabetical examples December 2000 replaces by DIN 3 rules for circuit diagrams of electrical engineering, May 1995 Replaced by DIN EN 61082-1 ??an 4 Rules for block diagrams of electrical engineering, May 1995 Replaced by DIN EN 61082-1 ??an 5 wiring, October 1996 Replaced by DIN EN 61082-4 6 rules for function diagrams, December 2002 Replaced by DIN EN 60848 7 Rules for maintenance-friendly design, in May 1995 Replaced by DIN EN 61082-1 ??and -2 9 type of wiring diagrams, May 1995 Replaced by DIN EN 61082-3 10 Design of layout plan in October 1996 Replaced by DIN EN 61082-4 60 Design of functional plans for measuring and control from February 1992 Replaced by DIN 407
DIN 40729 accumulators, galvanic secondary elements; Basic concepts
DIN 40734 lead-acid batteries - Fixed closed cells with positive grid plates - Cells in plastic containers, dimensions, weights DIN 40736 lead-acid batteries; Fixed cells with tubular positive plates; Cells in plastic containers Part 1 Capacities, main dimensions, weights Part 2 Capacities, main dimensions, weights DIN 40737 lead-acid batteries - Stationary batteries with positive tubular plates Part 3 Sealed batteries in plastic block boxes, Capacities, main dimensions, weights
DIN 40738 lead-acid batteries; Fixed cells with large positive surface plates, Engeinbau; Rated Capaci dimensions, weights DIN 40739 lead-acid batteries - Stationary vented batteries with positive grids - Capacities, main dime
DIN 40740 lead-acid batteries, Stationary batteries and accessories; Ceramic funnel plugs, ceramic pl indicator
DIN 40741 lead-acid batteries - Stationary valve regulated batteries with positive grid plates and Imm for industrial applications Part 1 Capacities, main dimensions, weights
DIN 40742 lead-acid batteries - Stationary valve regulated batteries with positive tubular plates and e Immobilized - Capacities, main dimensions, weights
DIN 40744 lead-acid batteries - Stationary valve regulated batteries with positive tubular plates and e Immobilized in plastic boxes block - Capacities, main dimensions, weights DIN 40763 nickel-cadmium batteries, nickel-cadmium cells closed with positive and negative plates fib Part 2 cells in plastic containers, discharge, discharge voltage, discharge times DIN 40768 steel accumulators; Sealed nickel-cadmium rechargeable batteries 6 V and 12 V of button planes, main dimensions and technical values DIN 40771 closed nickel-cadmium accumulators Part 1 Cells in plastic containers with pocket plates - Rated Capacities - Main dimensions Part 2 Cells in plastic containers with fiber structure plates - Rated Capacities - Main dimensions Part 3 cells in steel and plastic containers; installation types, dimensions DIN 40900 Graphical symbols for circuit diagrams Part 1-13 August 1997 Replaced by DIN EN 60617-1 ... 13 Bbl.1 Index, May 1994 WITHDRAWN without replacement DIN 41009 Electrical Communication Engineering; Mounting positions of components and counting of connections DIN 41015 Electrical Communication Engineering; Pawls and ratchet strip; Requirements, testing, DIN 41071 pointer for electric clocks Part 1 wedge-pointer Part 2 hole pointer DIN 41072 hand shafts for electric clocks; Connecting dimensions DIN 41073 pointer fittings for electric clocks; Connecting dimensions DIN 41074 suspension of electric clocks for interior DIN 41075 visibility for electric clocks DIN 41077 Two-pole plug for polarized slave clocks; Connecting dimensions DIN 41078 wall brackets for slave clocks and watches individual; Connecting dimensions
DIN 41079 fortifications of adverse movements of dials; Connecting dimensions DIN 41080 Time Service Part 1 Basic concepts, general terms Part 2 naming and structure of time servers (central clocks) Part 3 Terms and appointment of master clocks Part 4 terms, wording and structure of the slave clocks Part 5 definition, classification, naming and structure of the timer Part 6 terms and classification of individual watches DIN 41090 dials and hands for electric clocks; Overview and classification DIN 41091 dials for electric clocks Part 1 minute marker dials Part 3 hours dash dials Part 4 figures dials DIN 41092 pointer for electric clocks Baton Part 3 DIN 41096 Electric sirens for changing voltage rating of 125 to 500V Part 1 Main dimensions and technical values Part 2 Technical delivery conditions Part 3 rating plate Part 4 Canopy DIN 41097 pipe stand for electric sirens 125 to 500 V AC Part 1 rule execution with and without intermediate isolation protection, compilation of items Part 4 skylight Part 6 Accessories for electric sirens; catwalk and out board DIN 41098 Switch box for electric sirens for Voltages up to 380 V Part 1 Main dimensions and wiring diagram Part 2 Technical delivery conditions Part 3 rating plate DIN 41115 Cylindrical metal housing for electrical fließgepreßt, DIN 41116 Part 1 Cylindrical metal housing for electrical engineering with threaded pin fließgepreßt, DIN 41215 relays and related terms DIN 41300 Small transformers Part 1 Characteristic data, M, EI, SM and SE-cores (EI-waste) DIN 41301 Magnetic materials for transformers DIN 41307 small transformers, transformers and chokes; Accessories Part 3 Pressure piece for cores type E?, U? and 3 U? Part 4 stirrup for cores type UI and 3UI Part 5 Mounting Plates for cores type E, ED, EE, EF and EK; printed circuit magnetic axis horizontal DIN 41328 Methods of measurement for electrolytic capacitors Part 1 of the core resistance measurement of electrolytic capacitors multiple
Part 4 Measurement of DC voltage capacity DIN 41426 nominal values ??of resistors and capacitors DIN 41429 Colour coding of resistors and capacitors DIN 41488 Electrical division dimensions for cabinets Part 2 Low-voltage switchgear Part 3 High Voltage Switchgear up to row 20 N (24 kV) DIN 41494 Design for electronic equipment Part 3 devices stacking, dimensions Part 8 482.6 mm construction; Components of control panels, installation conditions, measurements DIN 41543 Contacts page for images and Oszillographenröhren; Main dimensions, inclusions DIN 41569 Miniature fuses; Miniature fuses, 3 kV, confused DIN 41570 Miniature fuses; Miniature fuses, 1.2 kV, confused DIN 41571 Miniature fuses; Miniature fuses 250 V, confused Part 2 medium time-lag (M) Part 3 was (T) DIN 41576 Miniature fuses; Miniature fuses indicator fuses 250 V, confused Part 1 Fast (F) Part 2 medium time-lag (M) DIN 41577 Miniature fuses; Miniature fuses indicator fuses 250 V, distinctive Part 1 Fast (F) Part 2 medium time-lag (M) DIN 41591 shaft ends for electromechanical components DIN 41593 Dimensions for threaded sockets for Electrically operated wave-mechanical components w DIN 41609 electron tubes; Electrode terminals, numbering labeling, DIN 41611 Solderless connections Part 4 clamp connections; Definitions, requirements, testing Part 9 winding insulation displacement connections, Terms, characteristics, specifications, tests
DIN 41612 connectorsfor printed circuits, indirect mating, 2.54 mm; several parts, in February 1999 R 60603-2 DIN 41615 connectors for plug-in technology, rectangular, pin diameter 1 mm and 1.6 Part 1 Common construction features, design overview Part 3 crimp dimensions of types C and D Part 5 ratings, requirements, tests DIN 41617 connectors for printed circuits, indirect mating, spacing 2.5 mm Part 1 Common construction features, design and liabilities; Dimensions of types L, M, N, and S Part 2 lessons, ratings, requirements, tests DIN 41618 connector contact strips with blade contacts 2.5 mm × 1 mm Part 1 Main dimensions Part 3 passport and catch parts Part 4 bolt housing and pans for plug contact strips to DIN 41618 and DIN 41622 DIN 41620 connectors for printed circuits (flat contacts, Single)
Part 1 female connectors, printed circuit boards DIN 41622 connector contact strips with blade contacts 3 × 1 mm Part 1 Dimensions DIN 41626 special contacts for multipole connectors Part 1 high power contacts (Type H) Dimensions, ratings, requirements, tests Part 2 Concentric contacts (type C), Dimensions, ratings, requirements, tests DIN 41631 stage rotary switch 41 mm × 54 mm; 13er- and 26er-sharing; Dimensions, ratings, require DIN 41632 stage rotary switch 28 mm × 39 mm; 12-sharing; Dimensions, ratings, requirements, tests
DIN 41633 stage rotary switch 17 mm in diameter, 10s and 12-pitch solder connections Axial; Dimens requirements, tests DIN 41634 stage rotary switch 17 mm diameter, 12-pitch solder connections radial Part 1 Main dimensions DIN 41635 Lever, design, installation dimensions, connection types; Switching principle DIN 41636 switches for Telecommunications Part 1 Climatic test classes, Measurements and Testing Part 2 dimensions, ratings, requirements, tests, Type A Part 3 dimensions, ratings, requirements, tests, Type B Part 4 dimensions, ratings, requirements, tests, Type E Part 5 dimensions, ratings, requirements, tests, Type D Part 6 dimensions, ratings, requirements, tests, Type F DIN 41640 Measurement and Testing for electromechanical components Part 54 test 23a: feedback resistor Part 80 test A: contact force, resilient female contacts DIN 41641 Tools for solderless electrical connections; Hand crimping tools Part 1 Definitions, requirements, testing Part 2 Dimensions DIN 41649 connector for shifting and testing, 2 mm diameter, for printed circuits Part 1 Dimensions and installation instructions Part 2 ratings, requirements, tests DIN 41650 specification for connectors Part 1 connectors for printed circuits
Part 2 Rectangular Connectors for frequencies below 3 MHz; General requirements and guide for the p specifications Part 11 connectors for printed circuits, design of detail specifications Part 12 Rectangular Connectors for frequencies below 3 MHz; Design of detailed specifications DIN 41652 connectors for plug-in technology, trapezoidal, round contacts ? 1 mm Part 1 Common construction features and dimensions; Design Overview Part 2 ratings, requirements, tests Part 3 Dimensions of type A; Solder joint for free wiring Part 5 dimensions of the type C, crimp terminals for free wiring DIN 41653 standard framework for teaching function for NF-connector; Calculation, General requireme DIN 41673 Miniature fuses; G-fuse base, 6.3 A, 250 V, flat, with screw cap, confused for fuse-links
DIN 41681 Miniature fuses, Fuse holder, 500 V to 3 kV, for confusable G-fuse links, fuse holder, G-scre
DIN 41682 Electrical Communication Engineering; Miniature fuses, Fuseholders, 6 A, 60 V, for confusa contact blade DIN 41683 Miniature fuses; Miniature fuses 6 kV, confused DIN 41684 Miniature fuses, miniature fuses, 10 kV, confused DIN 41686 Miniature fuses; Miniature fuses 500 V, confusingly slow medium (M), Fast (F) DIN 41698 Electrical Communication Engineering, Plugs, requirements, testing DIN 41700 Electrical Communication Engineering; Three-prong plug DIN 41701 Electrical Communication Engineering; Four-pin plug DIN 41714 Electrical Communication Engineering; connectors with circular contact arrangement 2-, 4Part 1 designs, dimensions DIN 41715 Electrical Communication Engineering; Connectors for telecommunications terminal units ( Part 1 Common features design overview Part 2 ratings, requirements, tests Part 3 types A, B, C, and R Part 4 Dimensions of types D, E, F, and S Part 5 Dimensions of types G, H and T DIN 41746 Stabilized Power Supplies Part 2 Guidelines for datasheet specifications, equipment with AC output DIN 41750 converter (terms) DIN 41751 converter; Semiconductor converters sentences and -Stromrichtergeräte, cooling methods DIN 41752 converter; Semiconductor converters appliances; performance characteristics DIN 41755 overlays on a DC voltage Periodic overlays Part 1 Definitions, measurement methods DIN 41756 converter; Load of converters Part 2 types of loads in DC Part 3 types of loads with AC DIN 41762 converter; Performance characteristics for Semiconductor converters sets Single crystal semiconductor converters Part 2 sets DIN 41772 converter; Semiconductor rectifier equipment, forms and symbols of the characteristics DIN 41773 converter Part 1 semiconductor rectifier equipment with IU characteristic for charging lead-acid batteries, guide
Part 2 semiconductor rectifier equipment with IU characteristic for charging of nickel / cadmium batte DIN 41774 converter; Semiconductor rectifier equipment with W-characteristic for charging lead-acid Requirements
DIN 41775 converter; Semiconductor rectifier equipment with W-characteristic for the loading of nicke nickel / iron batteries, demands DIN 41776 converter; Semiconductor rectifier equipment with I-characteristic for charging batteries; R DIN 41782 rectifier diodes DIN 41786 thyristors terms DIN 41850 Integrated circuits movie; Materials
Part 2 methods for the assessment of conductive pastes Part 3 methods for the assessment of dielectric pastes DIN 41855 Optoelectronic semiconductor devices
DIN 41868 housing for semiconductor devices, housing type 10, main dimensions, in May 1998 WITHD replacement DIN 41869 housing for semiconductor devices Part 1 housing type 23, main dimensions, March 1986 WITHDRAWN without replacement Part 2 housing type 34, main dimensions, November 1998 WITHDRAWN without replacement Part 3 housing type 11, main dimensions, July 1988 WITHDRAWN without replacement Part 4 housing type 12, main dimensions, November 1998 WITHDRAWN without replacement Part 5 Housing Type 13 main dimensions, November 1998 WITHDRAWN without replacement Part 6 housing type 14, main dimensions, September 1986 Replaced by DIN 41870-13 Part 7 Housing Type 15 main dimensions, November 1998 WITHDRAWN without replacement
DIN 41873 Housing for semiconductor devices and integrated circuits; Housing Type 5, main dimensio WITHDRAWN without replacement
DIN 41876 housing for semiconductor devices, Housing Type 18 main dimensions, in May 1998 WITHD replacement DIN 41881/2 conductor devices Part 2 Requirements and testing, metal case with ceramic insulator
DIN 41900 high frequency power capacitors with rated Voltages above 1 kV and reactive powers over parameters DIN 42013 spring washers for axial employment of ball bearings in small motors DIN 42020 shaft ends with tolerance ring small electric motors DIN 42021 stepper motors Part 1 attachment dimensions, name plate, electrical connectors Part 2 terms, symbols, units and characteristics DIN 42026 magnet segment for small engines Part 1 information dimension Part 2 principle of a device for dimensional inspection Part 4 limits visible error DIN 42027 servo motors; Classification, overview DIN 42028 plug connectors with push-on connections for small engines Part 1 Design and dimensions DIN 42111 Contactless snap switch Part 1 terms, Climatic test classes, test and measurement procedures Part 2 dimensions, ratings, requirements, tests, Type A
DIN 42112 push button switch with tactile feedback for printed circuits; Type A (12.5 x 12.5) mm, type Part 1 dimensions, ratings, requirements, tests DIN 42115 Membrane Switch Part 1 General, Terms, characteristics, specifications, tests Part 2 membrane keyboards without pressure point; Characteristics, requirements, testing
Part 3 Folientastfelder; Characteristics, requirements, testing DIN 42400 marking of terminals DIN 42402 connector name for Transformers and Reactors DIN 42403 connector designation for Power DIN 42405 Identification of equipment terminals Time service equipment and systems DIN 42508 Transformers - Oil Filled Power Transformers of 3150 kVA to 80000 kVA and U m up to 123 k DIN 42513 transformers, Transformers and Components labeling for Reactors (BKT) DIN 42534 transformers, bushings for indoor and outdoor, series voltage 45 kV up to 1000 A DIN 42537 transformers, bushings for outdoor U m 36 kV, 12.5 and 25 kA Part 1 compilation Part 2 items Part 3 mounting DIN 42538 transformers, bushings for attachment DIN 42544 transformers; pass valves, three-way valves; Requirements DIN 42545 transformers; Oil boom DN 25; Requirements and testing DIN 42547 transformers and inductors; rating plates; Execution DIN 42548 residual oil drain for transformers DIN 42552 Transformers - Oil level indicator with plug DIN 42553 transformers; Vents snow protection; Filling DIN 42558 transformers; Stoppers for vent and drain oil DIN 42561 transformers; Roll Part 2 load> = 10 t Part 3 pitches and gauges DIN 42568 transformers, outlet valve DN 15 and DN 32 for sampling and drain DIN 42600 transducer for 50 Hz Part 1 rows 0.5 to 45 N, U m 0.6 to 52 kV; General Guidelines Part 2 U m 0.6 to 52 kV; CT U m = 0.8 kV; Main dimensions Part 3 rows 0,5, 1 N to 45 N; VT series 10 N to 30 N, interior design with Gießharzisolation, main dime Part 4 U m 0.6 to 52 kV; support current transformer U m 12 kV, small design, main dimensions, indoo Part 5 U m 0.6 to 52 kV; support current transformer U m 12 to 36 kV, large design, main dimensions, Part 7 U m 0.6 to 52 kV; Voltage transformer U m 12 kV; Small design, main dimensions, indoor type Part 8 U m 0.6 to 52 kV; support current transformer U m 12 and 24 kV, Sleek design, main dimension Part 9 U m 0.6 to 52 kV; Voltage transformer U m 12 and 24 kV, Sleek design, main dimensions, indoo DIN 42601 transducer 50 Hz, U m from 72.5 kV and above - Basic requirements DIN 42673 AC motors with squirrel-cage rotors, surface cooled (standard motors) DIN 42676 AC motors with squirrel-cage rotors, internally cooled (standard motors) DIN 42801 connector pin for equipotential bonding conductors Part 2 bonding lines; Jack DIN 42802 connectors, non-protected for electrical Medicine DIN 42923 clamping rails for electrical machines DIN 42925 entries in the terminal box for three-phase squirrel cage motors with rated Voltages of 400
DIN 42961 nameplates (motors, transformers, etc.) DIN 42973 power series of electrical machines DIN 43021 cars and vehicles; Carbon brushes, dimensions and tolerances DIN 43051 cars and vehicles; carbon brush holders, connection dimensions DIN 43053 cars and vehicles; Insulators for Carbon Brush Holder DIN 43054 cars and vehicles; Pressure pads for carbon brush holder DIN 43070 cars and vehicles; Carbon Brush Holders Part 1 controls and audits Part 2 measurement and testing instructions DIN 43101 cars and vehicles; Electric rail vehicles Part 1 designations Overview Part 2 classification and terms Part 3 nominations for Power Trains Part 4 designation for high voltage devices Part 5 nominations for transformers Part 6 nominations for traction motor parts Part 7 nominations for auxiliaries Part 8 nominations for electrical equipment of the switching and control device Part 9 nominations for Monitoring and Safety Devices Part 10 nominations for lights and electrical heating appliances for rail vehicles Part 11 names for controllers Part 12 nominations for current bridges Part 13 nominations for electrical equipment and parts for the design and function Part 14 nominations for electrical appliances, items for structure and function Part 16 terms for components of power electronics
DIN 43102 cars and vehicles; Traction motors and auxiliary machinery; designation of the facet-definin of rotation DIN 43119 rotary bolt with ring groove for contact wire clamp for overhead lines Part 2 rotary bolt with thread DIN 43120 Electric railways; Bügelsplint for contact wire clamp DIN 43136 tension wires for overhead contact system DIN 43137 Electric railways, wires for ground and power return DIN 43138 Flexible cables for overhead contact lines and return lines DIN 43139 drums for contact wires DIN 43147 Electric Trains Part 1 dropper clamp for grooved contact wires and supporting cables Part 2 trailer clip for carrying cables 35 mm 2 , 70 mm 2 to 185 mm 2 Part 3 hanger clamp, sliding hanger clamp for supporting cables DIN 43148 Wedge sockets DIN 43530 accumulators; Electrolyte and water refilling Part 1 General
Part 2 electrolyte for lead-acid batteries Part 4 water and refill water for lead-acid batteries and alkaline batteries DIN 43600 transport wheels for switching devices and transducers DIN 43601 pitches and gauges of transport rollers of switching devices and transducers DIN 43605 connector for hydraulic pressure gauge port on high voltage equipment - Dimensions, requ
DIN 43607 Three-pole circuit breakers and switch-disconnectors for indoor installations; Rated voltage (normal) current 400-1250 A; Main dimensions DIN 43620 High and low voltage fuses with contact knives Part 1 NH fuse-links for AC 500 to 660 V and 440 V DC NH fuse bases Part 3 NH fuse-links for AC 500 to 660 V and 440 V DC
Part 6 NH bus-mounting fuse bases, fuse disconnectors NH-mounting fuse switch disconnectors and N on busbars up to 660 V AC DIN 43624 high-voltage fuses, rated Voltages 3 / 3.6 to 30/36 kV, single-pole fuse bases DIN 43625 high-voltage fuses; Rated voltage 3.6 up to 36 kV; Dimensions for fuses DIN 43627 Cable House connection boxes for HRC fuses size 00 up to 100 A 500 V and size 1 to 250 A DIN 43628 fuse boxes for cable protection fuses DIN 43670 aluminum bus bars; Rated for continuous current DIN 43671 Copper busbars; Rated for continuous current DIN 43673 busbars drilling and screw caps Part 1 busbars with rectangular cross-section Part 2 busbars with U-shaped cross-section DIN 43675 connectors for connecting bolt Part 1 flat connectors 400 to 3150 A, of transformer and wall penetrations less than 60 kV Part 2 flat connectors of transformer bushings for outdoor; U m 24 and 36 kV, 5 and 8 kA Part 5 octagonal fittings, over 10000 A, transformer bushings DIN 43684 switchgear; Mosaic images, partitions
DIN 43718 Measurement and control rules; bezels and front plates for measurement and control devic
DIN 43719 Measurement and control rules; Mechanical screen systems for the installation of instrume equipment
DIN 43735 Control technology - Electrical temperature - Replaceable inserts for resistance thermomet thermocouples DIN 43751 Measurement and control rules; Digital measuring devices Part 1 General requirements on terms, tests and data sheet specifications Part 2 instruments for measuring analog quantities, terms, tests and data sheet specifications Part 3 instruments for measuring digital quantities, terms, tests and data sheet specifications Part 4 instruments for the measurement of time-related variables, terms, tests and data sheet specific DIN DIN DIN DIN
43764 43765 43766 43767
Measurement Measurement Measurement Measurement
and and and and
control rules; Electrical temperature, thermometer with interchangeable control; Electrical temperature; Screw-in thermometers with G 1/2 control rules; Electrical temperature; Screw-in thermometers with G 1 control rules; Electrical temperature; Weld-in thermometer
DIN 43769 Measurement and control rules; Electrical temperature, thermometer without additional th
DIN 43772 Control technology - Metal thermowells and neck tubes for machine glass thermometers, d thermocouples and resistance thermometers - Dimensions, materials, testing DIN 43780 Indicating Measuring Instruments, Replaced by DIN EN 60051 DIN 43790 principles governing the design of line scales and pointers DIN 43802 scales of measuring instruments DIN 43807 Electrical Meters (panel meter)
DIN 43834 Measurement and control rules; Attachment for measurement and control devices for pane Fastener; Mounting holes in the unit DIN 43835 Attachment for Indicating measuring instruments; Fastener cone at housing, mounting arra DIN 43853 meter boards; Main dimensions, connection dimensions DIN 43854 sealing screws for electricity meters DIN 43855 Electricity meters; Signs DIN 43856 electricity meter tariff switching devices DIN 43857 electricity meters in molded insulation for direct connection of up to 60 A current limit Part 1 Dimensional phase meter Part 2 Dimensional Three-phase meter Part 3 main dimensions of the terminal cover for AC meter Part 4 main dimensions of the terminal cover for three-phase meter Part 5 main dimensions of the terminal cover for accessories DIN 43860 support equipment to the electricity meter nach DIN 43857 Part 2 Part 1 mounting bracket Part 2 ripple control receiver DIN 43865 counter DIN 43870 meter locations DIN 43871 Consumer units for built-in appliances up to 63 A DIN 43880 Installing Devices - dimensions and related mounting dimensions DIN 44013 reference equivalent diameter (Objective Bezugsdämpfungsmeßplatz OBDM); Configuratio DIN 44070 thermistor NTC thermistor DIN 44080 thermistor PTC DIN 44081 thermistor, thermistor, thermal machine protection, climate application class HFF DIN 44082 Thermistors; Three of a Kind PTC; Thermal machine protection; Climatic application class H
DIN 44300 information processing. The standard has been INITIALLY then WITHDRAWN in total and ind Replaced by the standard ISO / IEC 2382nd Part 1: General terms Part 2: Information representation Part 3: Data Structures Part 4: Programming Part 5: Structure of digital computing systems Part 6: Storage Part 7: x Part 8: processing functions
Part 9: processing operations DIN 44401 symbols in datasheets for electron tubes DIN 44402 Measurements of the electrical properties of electron tubes Part 1 Guidelines for measuring method Part 6 conditions to measure the noise figure Part 7 methods of measuring hiss and hum Part 8 Measurement of equivalent noise resistance Part 14 measurement of emission current from hot cathodes for high-vacuum tubes Part 16 measurement of electrode fault currents Part 17 measurement methods for picture tubes Part 19 measurement of noise due to mechanical or acoustic excitations Part 20 measuring the cross modulation of AM-AM transfer Part 21 measurement methods for cold-cathode display tubes DIN 44405 internal graticule for Oszillographenröhren DIN 44531 Electric hot water heater; Rules for connection instructions
DIN 44534 Electric hot water heater, hot water tank without thermal insulation (boiler), Hanging arran liters, testing
DIN 44535 Electric hot water heater, hot water tank without thermal insulation (boiler), Hanging arran liters, requirements DIN 44536 electric water; hot water heaters to 5 liters; Hanging arrangement, performance character Part 1 Definitions Part 2 exams Part 3 requirements DIN 44543 Domestic grills; Terms DIN 44544 Domestic grills; Examination DIN 44545 Domestic grills; Requirements DIN 44549 Electrical domestic hot plates; performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements
DIN 44550 electric cookers for household purposes; Automatic hotplates and automatic glass ceramic performance characteristics, tests
DIN 44551 electric cookers for household purposes; Automatic hotplates and automatic glass ceramic performance characteristics, requirements DIN 44558 Domestic-egg cooker, performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements DIN 44561 Electrical household ironing machines; Terms DIN 44562 Electrical household ironing machines; Examination DIN 44563 Electrical household ironing machines; Requirements DIN 44704 handles for power tools
DIN 44717 hand-held power tools; Suction; Connecting dimensions DIN 44766 resistance welding transformers Part 2 hanging transformers; Dimensions, characteristics Part 3 transformers with flange; Dimensions, characteristics DIN 44767 appliance coupler for the primary port of resistance welding transformers, 200 A, 550 V DIN 44770 Pneumatic welding cylinder, double acting, without damping, doubly charged Part 1 connection dimensions DIN 44771 connector angle 45 ° and 90 °, for resistance welding equipment DIN 44858 Electrical domestic cookers, timer, timers and timer; performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements DIN 44871 Electrical heating elements and heating elements Part 1 Definitions DIN 44872 Testing of Elektromagnesia DIN 44874 Electrical tubular heater with metal casing Part 1 calculation, design and requirements Part 2 diameter 6.5 mm and 8.5 mm; Connections Part 3 of diameter 6.5 mm and 8.5 mm; Determining the effects of aging and overload behavior DIN 44875 Electrical tubular heater with metal casing; Application DIN 44876 hex nipple pipe for electric radiator with metal cover DIN 44879 hex nut low, for nipple and screw heads for electrical tubular heating elements with metal DIN 44897
Part 1 Electric hot water heater, mixer taps open storage and boiler, for assembly on the table, conne allowable pressure losses DIN 44899 Electric Hot Water Heater Part 4 Calculation of the wall thickness of closed containers up to 50 liters nominal capacity, safety re Part 5 Guidelines for the calculation of the wall thickness of closed containers about 50 to 2000 liters Part 6 Nominal capacity to 1,000 liters; Conditions for low-noise design DIN 44901 electric water; hot water tank, standing arrangement 200 to 1000 liters Part 1 Shipping Dimensions for closed storage Part 2 Rated input DIN 44902 Electric hot water heater, hot water tank, hanging arrangement Part 1 5 to 15 liters, connection dimensions Part 2 30 to 150 liters; Connecting dimensions Part 3 of 5 to 150 liters Rated input Part 4 port values ??for open water heater DIN 44904 harness for electric stoves; Dimensions, requirements and testing DIN 44921 Electrical heating elements with metal cover Part 1 Dimensions Part 2 high-performance cartridge heaters; Mass
Part 3 requirements DIN 44922 Electrical Screw
Part 1 by screwing G 1 1/2 B and tubular heaters with metal sheath diameter 6.5 and 8.5 mm; Dimens inputs Part 2 with the screw head and the immersion heater with metal casing; Mass Part 3 requirements DIN 44926 Ceramic parts for electric heating elements Part 1 multi-hole tubes; Mass Part 2 Open multi-hole tubes; Mass Part 3 spiral plate with connecting parts; Mass DIN 44932 insulating beads DIN 44954 Electrical Appliances, Can opener, performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements DIN 44973 Domestic humidifier; performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements DIN 44974 Domestic fans; performance characteristics Part 1 Definitions Part 2 exams Part 3 requirements DIN 45020 designations and definitions in the field of wave propagation DIN V 45025 criteria in the field of radar technology
DIN 45401 acoustics, electro acoustics, standard frequencies for measurements, August 1997 Replace DIN 45500 home studio equipment ( Hi-Fi ) Part 1 General, in February 1996 Replaced by DIN EN 61305-1 Part 2 WITHDRAWN minimum requirements for FM receivers (tuners), May 1999 without replacement Part WITHDRAWN 3 Minimum requirements for record players, Apr. 1999 without replacement
Part WITHDRAWN 4 Minimum requirements for magnetic tape recorders for recording and playback, M replacement WITHDRAWN Part 5 Minimum requirements for microphones, May 1999 without replacement Part 6 Minimum Requirements amplifier, February 1996 Replaced by DIN EN 61305-3 Part WITHDRAWN 7 Minimum requirements speaker, May 1999 without replacement Part WITHDRAWN 8 Minimum requirements for Combinations and systems, May 1999 without replacem
Part WITHDRAWN 9 minimum requirements for Magnettonbänder 4 and 6 for sound recording, without replacement Part WITHDRAWN 10 Minimum Requirements for headphones, May 1999 without replacement DIN 45540 sound recording and playback, audio equipment; Measurement record, record frequency DIN 45621 language for the hearing test
Part 1 input and multi-syllabic words Part 2 sets DIN 45630 Fundamentals of sound measurement DIN 45631 Calculation of loudness level and loudness of the sound spectrum; Zwicker method DIN 45635 Noise levels at machines; Air enveloping surface method Part 1 Followed procedure for 3 Accuracy classes Part 8 frame method Part 11 combustion engines Part 12 Electrical Switchgear Part 14 air-cooled heat exchangers (air cooler) Part 15 of turbomachinery units in thermal power plants for electricity Part 16 machine tools Part 22 torches Part 23 Gear Part 25 oxyfuel and plasma torch and machines Part 26 hydraulic pumps Part 31 shredders Part 33 Construction 34 part Actuated fastening tools Part 37 machines for processing plastics and rubber Part 38 fans Part 40 machine sets in hydroelectric power plants and water pumping equipment Part 41 Hydraulic Power Units Part 45 continuous conveyor Part 46 cooling towers Part 47 chimneys Part 49 Surface treatment plants Part 50 Fittings Part 51 cameras for motion events Part 52 diesel locomotives pits and diesel-powered rail corridor tracks Pit Part 53 diesel cats Part 54 Pit tyred vehicles Part 55 shunting trolleys with friction wheel and / or gear drive Part 56 air heaters, air heaters, fan parts of air treatment apparatus Part 57 outboard motors Part 60 silent and motion picture projectors Part 61 cranes Part 62 Machines and equipment for the production of bricks, plates, pipes and precast concrete Portion 1601 machine tools for metal working lathes Particular requirements for Portion 1602 machine tools for metal working, Particular requirements for the forging Portion 1603 machine tools for metal working, Particular requirements for multi-purpose presses
DIN 45640 exterior noise measurements on vessels on inland waters Part 2 enveloping surface method for the determination of sound power level DIN 45641 Averaging of sound DIN 45642 Measurement of traffic noise DIN 45643 Measurement and assessment of aircraft noise DIN 45645 Determination of rating levels from measurements Part 1 noise levels in the vicinity Part 2 Determination of the rating level at the workplace activities below the level range of hearing im DIN 45657 Sound Level Meter - Additional requirements for special measuring tasks DIN 45661 Vibration Measurement - Definitions DIN 45662 Vibration measuring - General requirements and test DIN 45667 Classification methods for evaluation of vibration random DIN 45669 Measurement of vibration immission Part 1 vibration meter - Requirements and tests Part 2 measurement methods DIN 45672 vibration measurements in the vicinity of railway tracks Part 1 measurement method Part 2 ratings DIN 45673 Mechanical vibration - Resilient elements in railway routes Part 1 Definitions, classification, test methods Part 2 Determination of static and dynamic characteristics in tracks Part 5 Laboratory test procedures for fiber mats Part 6 Laboratory test procedures for footings of concrete sleepers Part 7 Laboratory test procedures for resilient elements of mass-spring system Part 8 Laboratory test procedures for continuous elastic rail supports DIN 45676 Mechanical input impedance and transfer functions of the human body DIN 45677 Mechanical input impedance of the human hand-arm system DIN 45678 Mechanical vibration - Articulated trucks - Laboratory evaluation of the vehicle seat vibrati
DIN 45679 Mechanical vibration - Measurement and evaluation of the grip and feed forces for assesin of the hand-arm system DIN 45680 Measurement and assessment of low-frequency noise levels in the vicinity
DIN 45681 Acoustics - Determination of tonal components of noise and determination of a tone adjust assessment of Geräuschimissionen DIN 45682 sound immission DIN 45684 Acoustics - Determination of aircraft noise exposure at airfields Part 1 calculation method Part 2 Determination of acoustic and flight operational parameters
DIN 45687 Acoustics - Software products for the calculation of the sound propagation outdoors - Quali test
DIN 45688 Particular requirements for the competence of testing laboratories for noise and vibration i pollution control DIN 45691 Noise allotment
DIN 45692 Measurement simulation of auditory perception Focus DIN 46200 Conductor connection bolt up to 1600 A, Execution and assignment of the current strength DIN 46202 connector pin for switching devices, sensors and surge from 52 kV DIN 46206 connectors for electrical equipment Part 2 flat connectors> = 40 A, main dimensions and assignment Part 3 flat connectors for devices from 52 kV; Main dimensions assignment, DIN 46211 Punched cable lugs for copper conductors DIN 46215 Punched hole with solder lugs DIN 46216 Stamped solder lugs with slot DIN 46218 Punched Leitungsösen; Crown molding DIN 46220 Straight cable lugs, pressed, cast for copper conductors DIN 46221 angle cable lugs, pressed, cast for copper conductors DIN 46225 Punched claw lugs for insulated cables with Isolierungsumfassung DIN 46227 clamp terminals for copper conductors Ferrules DIN 46228 Part 1 tube shape without plastic sleeve Part 2 crimp with and without Isolierungsumfassung Part 3 conductors Including, but Isolierungsumfassung Part 4 Tubes with plastic sleeve DIN 46229 cable lugs, designation of connecting sides DIN 46230 for solderless terminals connections, stick form, without insulating sleeve for copper condu DIN 46231 pin terminals for solderless connections, insulated, for copper conductors DIN 46234 for solderless terminals connections, ring type, without insulating sleeve for copper conduc DIN 46235 cable lugs for crimp connections, link design for copper conductors DIN 46236 Punched claw lugs with Isolierungsumfassung for soldering DIN 46237 for solderless terminals solderless connections, insulated, for copper conductors DIN 46238 spring terminals for telecommunication lines with Kunststoffisolierhülle DIN 46249 connectors flat, not isolated Part 1 requirements, tests DIN 46252 cable lugs for telecommunication lines with Kunststoffisolierhülse DIN 46257 cable lugs, connecting pipe for telecommunication lines with textile and rubber insulation DIN 46260 pin terminals for low voltage Part 1 compilation Part 2 BOM DIN 46262 pin terminals for low voltage Part 1 insulators Part 2 bushing bolts Part 4 rings, clips, washers, pads DIN 46264-through terminal blocks with Gießharzisolator for high voltage DIN 46265-through terminal blocks with ceramic insulator for high voltage Part 1 compilation
Part 2 BOM DIN 46266-through terminal blocks for high voltage Part 1 ceramic insulator Part 2 bushing bolts Part 3 flanges, washers DIN 46267 connector compression, tensile not Part 1 for copper conductors Part 2 aluminum conductors DIN 46268 circular connectors Part 1 round connector sleeves with snap tabs for locking into housing with round connector 3.5 mm Part 2 round pin plug with grid tongues for locking into housing for round receptacles 3.5 mm DIN 46274 connector terminals B DIN 46276 Elastic bands for busbars and flat terminals Part 1-Laminated Flexible Part 2 Laminated High Flexibility DIN 46284 two- and three-pin socket terminal (terminal equipment), 380 V AC 440 V, for conductors u DIN 46285 two- to three-pin socket terminal strips (lamp terminals), 380 V AC 440 V, for conductors u DIN 46288 connector plates for lead terminals DIN 46294 Rectangular Connectors Clamp with 6 terminal studs; Main dimensions DIN 46295 Rectangular Connectors Clamp with 6 slotted bolt Part 1 Main dimensions Part 2 connecting bridges and forcing nuts Part 3 cable lugs DIN 46300 Installation material; Mounting screw for electricity meters and controllers on counter field DIN 46329 cable lugs for crimp connections; ring mold for aluminum conductors DIN 46330 Short receptacles without insulating sleeve Part 1 of connector width 2.4 Part 2 of connector width 2.8 DIN 46339 Connectors with spring-loaded test unit to terminal blocks; Dimensional plug and socket DIN 46340 Receptacles with locking tongue for locking into housing Part 1 of connector width 2.8 Part 3 of connector width 6.3 Part 4 of connector width 9.5 Part 5 of connector width 7.7 DIN 46341 connectors for solderless connections, without insulating sleeve Part 1 for copper conductors DIN 46342 connector flat, straight and angled, with mounting hole Part 1. Receptacles DIN 46343 flat connector with locking tongue for locking into housing Part 1 for faston 2.8 Part 2 faston 4.8
Part 3 for faston 6.3 Part 4 faston 9.5 DIN 46345 Receptacles with flat plug for connector width 6.3 DIN 46346 Receptacles for lateral conductor connection for plug width 6.3 DIN 46380 production and transport of cables and wires - Definitions DIN 46391 coils for the supply of cables, wires and ropes Part 1 Dimensions Part 2 Technical delivery conditions for wooden cable reels Part 3 drums with diameter over 2800 mm; Mass Part 4 Technical delivery conditions for steel coils DIN 46392 coils for the supply of insulated wires Part 1 Dimensions DIN 46395 machine coils DIN 46396 container, container casing inside diameter about 500 mm for the manufacture of cables Part 2 cables and wires DIN 46397 coils for the production of wires Part 11 Spools with rectangular flanges, Dimensions Part 12 Spools with rectangular flanges, technical specifications Part 21 spools with conical flanges, Dimensions Part 22 spools with conical flanges, technical specifications Part 31 test methods DIN 46400 steel flat products with special magnetic properties;
Part 1 electrical sheet and strip, cold rolled non-oriented, final anneal, technical specifications, in Febr by DIN EN 10106 Part 1 Bbl.1 core loss at frequencies above 100 Hz, in February 1996 Replaced by DIN EN 10106
Part 2 electrical sheet and strip, cold rolled non-oriented, not final anneal, technical specifications, in F Replaced by DIN EN 10126 Part 3 electrical sheet and strip, grain oriented; Technical delivery, February 1996 Replaced by DIN EN
Part 4 electrical sheet and strip of alloy steel, cold rolled non-oriented, not final annealed; Technical de 1996 Replaced by DIN EN 10165 DIN 46420 Round Aluminium Wires for Electrical Purposes, Drawn; Mass DIN 46424 switchgear; Pressed U-profiles of aluminum, for tracks DIN 46425 Round Aluminium Wires, drawn accurately set for electrical engineering; Mass DIN 46431 round copper wire, just pulled for electrical engineering; Mass DIN 46452 flat wires for electrical engineering; Semi-finished products for winding wire, dimensions DIN 46453 Winding Wires Part 3 round wires, isolated, single or multiple wound; Testing and measurement techniques Part 6 wires resistance alloys; Determination of the temperature coefficient of the DC resistance DIN 46460 Winding wires, round wires from resistance alloys Part 1 blank; Technical delivery conditions Part 2 enameled Directly solderable, type V; Technical delivery conditions Part 3 enameled, heat resistant with temperature index 180, Type 180 W; Technical delivery condition
DIN 46463 Winding wire, round wire of nickel-resistance alloys, plain; Mass, resistance values, weights DIN 46464 Winding wire, round wire of resistance alloys oxidized insulating; Technical delivery conditi DIN 46465 Winding wire, flat wire of resistance alloys, plain; Dimensions, resistance values
DIN 47100telecommunications lines; Identification of the core, colors of the outer shells, November 19 without replacement DIN 47101 telecommunications lines, design, dimensions, presentation drawings for DIN 47104 Tinsel for telecommunication lines DIN 47223 connector RF 7/16; Impedance 50 ? DIN 47225 RF connector 1/3, impedance 50 ?; Connecting dimensions DIN 47226 RF coaxial connector 1.8 / 5.6, Impedance 50 ?; Connecting dimensions DIN 47227 RF coaxial connector 9/21, hermaphroditic connector, impedance 50 ?; Connecting dimens DIN 47231 RF coaxial connector 4.1 / 9.5, impedance 50 ?; Connecting dimensions DIN 47232 RF coaxial connector 21/48 Part 1 with flange, impedance 50 ?; Connecting dimensions Part 2 with union nut, impedance 50 ?; Connecting dimensions DIN 47233 RF coaxial connector 29/66 Part 1 with flange, impedance 50 ?; Connecting dimensions Part 2 with union nut, impedance 50 ?; Connecting dimensions DIN 47234 RF coaxial connector 43/98, impedance 50 ?; Connecting dimensions DIN 47235 RF connector 2 / 5.5; Impedance 50 ? DIN 47236 connector RF 4/11; Impedance 50 ? DIN 47237 connector RF 8/22; Impedance 50 ? DIN 47280 Part 2 RF connectors for Impedance 50 ?; Connector sizes, overview DIN 47295 RF connector 1.6 / 5.6; Characteristic impedance 75 ohms DIN 47297 RF connector 1.0 / 2.3; Impedance 50 ? DIN 47301 HF-line technology DIN 47302 High Frequency (HF) -Hohlleiter Part 1 rectangular tube, dimensions, frequency range, attenuation Part 2 round pipe dimensions, frequency range, attenuation Part 3 square tube, Mass, damping frequency range, Part 10 waveguide tube requirements DIN 47304 high frequency (HF) -Hohlleiter; waveguide tube tests DIN 47386 Coaxial RF cable 0.8 / 4.5, fully insulated, hochbiegsam, Z = 75 ? DIN 47400 cords for telecommunications equipment; Terms DIN 47409 taper sleeves for telecommunication lines DIN 47410 lines for telecommunication systems and information processing systems; Technical delive
DIN 47411 Telecommunications cord with stranded wire with PVC insulation and textile outer shell, wi protected DIN 47412 Telecommunications cord with stranded wire Part 1 with PVC insulation and PVC outer sheath, core, splash-proof Part 2 with PVC insulation PVC outer sheath without, core, moist air protected
DIN 47413 Telecommunications cord with stranded wire with PVC insulation and textile outer shell; pa protected DIN 47414 Telecommunications cord with stranded wire with PVC insulation and PVC outer sheath, pa DIN 47453 Telecommunications Tinsel cord with textile insulation and textile outer shell, core, for dry DIN 47460 Telecommunications cord with Tinsel, PVC insulated and textile outer shell, wire, moist air p DIN 47461 Telecommunications cord with Tinsel B, with PVC insulation and PVC outer sheath, wire, sp DIN 47462 Telecommunications cord with tinsel, with PVC insulation, wire, braided, splash-proof DIN 47463 Telecommunications cord with Tinsel E, with PVC insulation and PVC outer sheath, wire, sp DIN 47600 Cast Metal Joint Boxes for Power Cables up to 10 kV Part 1 protective sleeves Part 2 inner sleeves Part 3 Correlation of Joint Boxes with Paper insulated cables, assignment of the copper compound Rop Part 4 Internal structure for paper insulated cables Part 5 Installation instructions for paper insulated cables Part 6 Allocation of Joint Boxes with plastic insulated cables 0,6 / 1 kV Part 7 Internal construction for plastic-insulated cable 0,6 / 1 kV
DIN 47606 Cast Metal Joint Boxes for power cables with Individually shielded cores from 10 kV to 30 k DIN 47608 connector blocks with insulation displacement contacts for telecommunication systems Part 2 requirements, testing
DIN 47609 Weatherproof plastic Verzweigerschränke for telecommunication, control and signal cables testing, DIN 47615 cabinets for telecommunications equipment - Dimensions, Sizes DIN 47619 splicing of telecommunication cables Part 1 cable with symmetrical stranding
DIN 47624 clamping sleeves made of plastic for telecommunication cables with metallic fibers and op Requirements and tests DIN 47626 mantle terminals for telecommunication cables; Requirements, testing, DIN 47627 Solderless wire connections in sleeves for telecommunication cables; Requirements, testin DIN 47630 house connecting sleeves cast metal, up to 1000 V Part 1 Dimensions Part 2 Internal construction for distribution cable and drop cable NKBA NKBA Part 3 Installation instructions for distribution cable and drop cable NKBA NKBA Part 4 Internal structure for distribution cable and drop cable NKBA NYCY Part 5 Installation instructions for distribution cable and drop cable NKBA NYCY Part 6 Internal structure for distribution cable and drop cable NAKLEY NYCY Part 7 Installation instructions for distribution cable and drop cable NAKLEY NYCY Part 8 Internal structure for distribution cable and drop cable NYCWY NYCY Part 9 Installation instructions for distribution cable and drop cable NYCWY NYCY Part 10 Internal structure for distribution cable NYY and drop cable NYY Part 11 Installation instructions for distribution cable NYY and drop cable NYY DIN 47634 sleeves of heat-shrinkable plastic for telecommunication cables; Requirements; Exams
DIN DIN DIN DIN DIN DIN
47635 seal grooves and folds for cable fittings of cast metal 47642 cable clamps cast metal, for sets 47643 sleeves Cover for Cable Assembly 47645-shrinkable plastic caps of heat for telecommunication cables; Requirements, testing, 47658 cable branch terminals in the house connecting sleeves for copper and aluminum conducto 47659 Ground terminal for wavy concentric copper conductors up to 150 mm2
DIN 48004 Insulators for overhead power lines; Insulators for supporting insulators with internal fixatio from 10 to 30 kV DIN 48006 Insulators for overhead power lines Part 1 long rod insulators LP pan with caps Part 2 long rod insulators LG with fork caps Part 3 solid core insulators UK DIN 48016 threaded cap for attaching supporting insulators for overhead power lines up to 1000 V DIN 48031 reels for cables DIN 48044 overhead power lines; Straight insulator supports DIN 48045 overhead power lines; Curved insulator supports DIN 48050 overhead power lines; Just insulator support Part 1 conical Part 2 cylindrical DIN 48051 overhead power lines Part 1 Curved insulator supports, rule execution Part 3 Curved insulator supports for screwing DIN 48055 insulator supports for telecommunication overhead lines Part 1 Straight Support Part 2-U supports Part 3 hooks Support Part 4 notches DIN 48062 overhead power lines Part 1 cup caps for insulators Part 2 fork caps for insulators DIN 48065 Part 1 Klöppelösen without protective fittings Mounting for U-bolts Part 2 Klöppelösen with protective fittings Mounting for U-bolts Part 3 Klöppelösen with protective fittings for connecting mounting bolts DIN 48066 joints Part 1 Wishbone Part 2 guy joints DIN 48067 Part 1 Pfannenösen without protective attachment fittings Part 2 Pfannenösen with protective attachment fittings DIN 48068 Protection fitting attachment; Connecting dimensions
DIN 48069 Part 1 double eyelets without protective attachment fittings Part 2 double end fittings with protective attachment DIN 48070 spacer Part 1 spacer Triangle Part 2 trapezoidal and rectangular spacer DIN 48072 Part 1 branch terminals for aluminum cables and steel-aluminum conductors for overhead power lines Part 2 branch terminals for copper wires and copper conductors for overhead power lines DIN 48073 connecting bolts DIN 48074 plates and forks; Connecting dimensions DIN 48075 Part 1 power terminals for aluminum conductors and aluminum-steel cables for overhead power lines Part 2 power terminals for copper and bronze parts for overhead power lines DIN 48077
Part 1 accessories for overhead lines and substations; Terms of accessories for insulators, insulator str Erdseilbefestigungen DIN 48078 Part 1 fork lugs for connection lug-side pin connector Part 2 fork lugs for lug-side U-bolt connection DIN 48083 inserts in pressing for press fits Part 1 Mechanical presses to 15 and to 60 kN nominal compressive force; Connecting dimensions Part 3 Hydraulic Presses to 300, to 450 and up to 1000 kN nominal compressive force; Connecting dim Part 4 dimensions of the hexagonal the DIN 48083 inserts in pressing for press fits Part 1 Mechanical presses to 15 and to 60 kN nominal compressive force; Connecting dimensions Part 3 Hydraulic Presses to 300, to 450 and up to 1000 kN nominal compressive force; Connecting dim Part 4 dimensions of the hexagonal the DIN 48084 Part 1 conductors and terminals in switchgear with rated Voltages from 60 kV; Application DIN 48085 tensile compression connector, Part 1 for copper conductors Part 2 for aluminum conductors Part 3 for aluminum and steel ropes DIN 48087 Portable equipment for earthing and short-circuiting; Spindle shaft for connecting compone DIN 48088 termination site for earthing and short-circuiting devices Part 1 ball stud Part 2 cylinder bolts with groove for earth-side connection Part 3 bracket fixed point for conductors (wires, pipes) Part 4 cup benchmark for conductors (wires, pipes) Part 5 connector for ground lines
DIN 48108 Ceramic parts for electrical engineering; Amended Ask for insulation Part 1 corrugation Part 2 Splitting Part 3 wave profile
DIN 48113 post insulators for switchgear and controlgear for Voltages above 1 kV; Assignment of term strength DIN 48115 umbrellas for construction porcelain; Dimensions, Kriechwegbestimmung DIN 48124 bushings for hydrogen cooled generators Part 1 course cooled feed throughs Part 2 liquid-cooled feed throughs Part 3 gas-cooled feed throughs
DIN 48125 wall penetrations for outdoor-indoor plants, 45N and 45S series to 150N and 150S; Connec dimensions DIN 48138 Support insulators; Connecting dimensions DIN 48139 plate supporting insulators; Connecting dimensions DIN 48140 telecommunications overhead lines; Insulators RMK DIN 48141 telecommunications overhead lines; Insulators RMd DIN 48145 telecommunications overhead lines; Insulator RMü DIN 48150 overhead power lines; Support insulators N, rated voltage less than 1 kV DIN 48152 overhead power lines; Zugisolator Z, rated voltage below 1 kV DIN 48154 Part 1 overhead power lines; Shackle insulators S, insulating Part 2 overhead power lines; Shackle insulators S, Ironing DIN 48156 overhead power lines; Isolierei E, rated voltage less than 1 kV DIN 48170 roof rack for overhead power cables of rated Voltages up to 1000 V; Compilation, items DIN 48172 overhead power cables, rated voltage less than 1 kV; Roof rack introduction head, compila DIN 48173 overhead power cables, rated voltage less than 1 kV; Roof anchors, compilation, items DIN 48174 Part 1 crossmember for wood poles for overhead power cables of rated Voltages up to 1000 V Part 2 crossmembers for roof supports for overhead power cables of rated Voltages up to 1000 V Part 3 cross members for wooden poles and roof rack for overhead power cables of rated Voltages up DIN 48175 umbrella stand-house connections Part 1 standard type, degree of protection IP 40, for overhead power cables of rated Voltages up to 10 Part 2 Special versions, IP 54, for overhead power cables of rated Voltages up to 1000 V DIN 48176 roof rack brace for overhead power lines; Compilation, items DIN 48200 wires for wire ropes Part 1 copper wire Part 2 wires from wrought copper alloys (Bz) Part 7 steel wires copper (copper clad steel) DIN 48201 Part 1 Conductors - Ropes made of copper Part 2 Conductors; Ropes made ??of wrought copper alloys (Bz)
Part 3 Conductors, Steel ropes Part 7 Conductors; Ropes made ??of steel copper (copper clad steel) DIN 48203 Wires and cables Part 1 for copper cables; Technical delivery conditions Part 2 wires and cables for lines of wrought copper alloys (Bz); Technical delivery conditions Part 3 wires and ropes for steel pipelines; Technical delivery conditions Part 7 wires and cables for lines of steel copper (copper clad steel); Technical delivery conditions DIN 48207 Cable conductors; Laying of overhead conductors DIN 48217 connector notch for overhead power lines and railway catenary systems DIN 48300 wires for telecommunication overhead lines DIN 48319-bolts for overhead power lines DIN 48323 and communication overhead power lines; Turnbuckle for anchoring ropes DIN 48324 telecommunications lines and electric power lines below 1 kV, Tie rod, front plate, ring nut DIN 48327 wire splices for telecommunication overhead lines DIN 48328 telecommunication lines and overhead powerlines below 1 kV; Anchor blocks DIN 48342 power and telecommunication overhead lines; Wire rope tension clamp DIN 48345 crampons for wooden poles DIN 48350 and communication overhead power lines; Wood poles DIN 48351 overhead power lines; A mast Part 1 Main dimensions Part 2 bolts, nuts, washers DIN 48353 Part 1 reinforced concrete poles and -querträger for single cables up to 20 kV Part 2 reinforced concrete poles and -querträger; Guidelines for the selection of poles DIN 48500 Power Capacitors; Technical delivery conditions DIN 48699 related labeling of tools for working on live parts DIN 48803 lightning protection system; Arrangement of components and installation dimensions DIN 48830 lightning protection system; Description DIN 49073 socket boxes made of metal or insulating material Part 1 for receiving installation devices up to 16 A 250 V Part 3 for recessed installation and for receiving sockets nach DIN DIN 49440 Bipolar earthed sockets, 10 A DC / AC 16 A, 250 V Part 1 Main dimensions Part 2 Portable multiple outlets, combination of sockets 16 A 250 V and 2.5 A 250 V sockets - Main dim Part 3 two pin connector sockets splash proof, Part 4 lessons for coupling sockets Part 5 for installation in switch boxes; Mass Part 6 for use on Mounting surfaces for coupling sockets and portable socket-outlets; Mass DIN 49441 Bipolar plug with earthing contact Part 2 Bipolar plug with earthing contact splash proof, Part 3 Education for plug external diameter; Tester
DIN 49445 Three-pole sockets with neutral and protective earth contact 16 A AC 400/230 V DIN 49447 Three-pole sockets with neutral and protective earth contact 25 A AC 400/230 V DIN 49670 Lessons for fluorescent lamp sockets with protective tube
DIN 49802 preheating conditions for starterless operated tubular fluorescent lamps; Identical with IEC (Report) DIN 49810 Incandescent Part 3 lamps Shockproof Part 4 lamps for flameproof and explosion proof Hanging Lamps Part 5 lamps for flameproof and explosion proof hand lamps DIN 49812 Incandescent Part 1 tube lights, bulbs lamps Part 2 drops lamps, candle lamps wholesale Part 3 mushroom lamps Part 4 indicator lamps for flameproof and explosion proof indicator lights DIN 49833 Candle Small lamps, Illu-free lamps DIN 49837 lamps for hand and Employment headlights DIN 49838 Part 2 telecommunications lamps with lamp base BA7s DIN 49860 metal halide lamps with daylight-like radiation distribution Part 2 sports lighting DIN 49970 Electric lights, suspension tubes of metal DIN 49972 classification and description of new illuminant (IEC TR 60972: 1989 + A1: 1991) DIN 49978 Electric lights; support pieces DIN 49979 Electric lights; Cut DIN 49980 Electric lights, ceiling hooks, ceiling caps DIN 49982 Electric lights; Pipe Hanger DIN 49984 Electric lights; seal profiles for glass shades with flange nach DIN 49993 DIN 49985 Electric lights; Gasket for lighting glass edge with screws to DIN 49900 DIN 49990 Electric lights; Lighting glass with Schraubrand DIN 49992 Electric lights; Lighting glass with round hole edge DIN 49993 Glow glasses with flange DIN 49999 lighting glass Part 1 round handle, punch and flange edges, connecting dimensions Part 2 round hole edges for Schraubring- and pen holder; Connecting dimensions DIN 50000-59999 [ Edit ] DIN DIN DIN DIN DIN
50017 50018 50021 50049 50050
condensation test climates test to humid atmospheres Containing sulfur dioxide spray tests with different sodium chloride solutions Types of inspection, August 1995 Replaced by DIN EN 10204 Testing of Materials; Burning behavior of materials
Part 1 small burning cabinet Part 2 Big Brennkasten DIN 50051 Testing of Materials; Burning behavior of materials, burners DIN 50055 Lichtmeßstrecke for smoke testing DIN 50100 Testing of materials; Fatigue test, words, symbols, implementation, evaluation DIN 50103 Testing of metallic materials - Rockwell hardness test Part 3 Modified Rockwell method and Bm Fm for sheet steel DIN 50104 pressure test of hollowbodies; Leak test up to A Certain pressure value; General requireme DIN 50106 Testing of Metallic Materials; Compression test DIN 50113 Testing of Metallic Materials; Fatigue test DIN 50115 Testing of Metallic Materials; Charpy impact test; Special sample shape and evaluation DIN 50116 Testing of zinc and zinc alloys; Impact test DIN 50125 Testing of metallic materials - Tensile test pieces DIN 50145 tensile test for metallic materials, April Replaced in 1991 by DIN EN 10002-1 and DIN EN 1
DIN 50150 testing of steel and cast steel; Conversion table forVickers Hardness . Brinell . Rockwell har strength , October 2000 Replaced by DIN EN ISO 18265 DIN 50159 Metallic materials - Hardness testing using the UCI method Test methods Part 1 Part 2 Verification and calibration of hardness testers DIN 50190 Laser Technology - Hardness depth of heat-treated parts Part 3 Determination of the nitriding Part 4 Determination of the fusion hardening depth and the fusion depth DIN 50280 load test of radial bearings; General
DIN 50320 Wear: concepts, systems analysis of wear Processes, structure of the wear area, November without replacement
DIN 50450 Testing of materials for semiconductor technology; Determination of Impurities in carrier g gases Part 1 Determination of water impurity in hydrogen, oxygen, nitrogen, argon and helium by using a Diphosphorpentoxidzelle
Part 2 Determination of the impurity oxygen in nitrogen, argon, helium, neon and hydrogen by Means measuring
Part 3 Determination of Impurities into methane, hydrogen, oxygen, nitrogen, argon, helium and flame with a detector (FID) Part 4 Determination of C 1 -C 3 hydrocarbons in gas chromatography with nitrogen
Part 9 Determination of oxygen, nitrogen, carbon monoxide, carbon dioxide, hydrogen and C 1 -C 3 hy hydrogen chloride with DIN 50451 Testing of materials for semiconductor technology - Determination of trace elements in liqu Part 1 silver (Ag), gold (Au), calcium (Ca), copper (Cu), iron (Fe), potassium (K) and sodium (Na) in nitr
2 part of calcium (Ca), cobalt (Co), chromium (Cr), copper (Cu), iron (Fe), nickel (Ni) and zinc (Zn) in h Means of plasma-excited emission spectrometry
Part 3 of aluminum (Al), cobalt (Co), copper (Cu), sodium (Na), nickel (Ni) and zinc (Zn) in nitric acid b Part 4 Determination of 34 elements in high purity water by inductively coupled plasma mass spectro
Part 5 Guidance on the selection of materials and Their suitability for devices for sampling and sample trace element determination in the range of micrograms per kilogram and nanograms per kilogram DIN 50452 Testing of materials for semiconductor technology - Methods for Teilchenanalytik in liquids Part 1 Microscopic particle determination Part 2 particle determination of optical flow particle counters Part 3 calibration of optical Durchflußpartikelzählern DIN 50453 Testing of materials for semiconductor technology; Determining the etch rates of etching M Part 1 silicon single crystals; Gravimetric method Part 2 silica layers; Optical method DIN 50600 Testing of Metallic Materials; Metallographic micrographs, imaging scales and formats DIN 50905 Corrosion of metals - Corrosion tests Part 1 Principles Part 2 sizes with uniform corrosion surface corrosion Part 3 sizes under non-uniform corrosion and localized corrosion without mechanical stress Part 4 Implementation of chemical corrosion tests without mechanical stress in liquids in the laborator
DIN 50914 test for resistance to intergranular stainless steel corrosion, copper sulfate-sulfuric acid me Replaced in 1998 by DIN EN ISO 3651-2 DIN 50918 Corrosion of metals; Electrochemical corrosion testing DIN 50920 Corrosion of metals; Corrosion tests in flowing liquids Part 1 General
DIN 50923 Electroplated coatings - duplex systems from zinc or zinc alloy coatings with organic coatin materials
DIN 50930 Corrosion of metals - Corrosion of metallic materials in the interior of pipes, tanks and appa by water Part 6 influencing the composition of drinking water DIN 50938 burnishing of components made of ferrous materials - Requirements and test methods DIN 50957 test of electrolytic baths; Galvanisierungsprüfung with the Hull cell, general principles DIN 50958 Electroplated coatings - Modified Corrodkote corrosion test (mod CORR test). DIN 50960 Electroplated coatings Part 2 Drawing specifications DIN 50961 Electroplated coatings - Zinc coatings on iron and steel - Terms, testing and corrosion resis DIN 50962 Electroplated coatings - Chromated zinc alloy coatings on ferrous materials DIN 50965 Electroplated coatings - tin coatings on iron and copper materials DIN 50969 Avoiding production induced hydrogen-induced brittle fracture of high-strength steel comp Part 1 Preventative Measures Part 2 exams DIN 50970 Electrodeposited coatings produced - nickel chemicals for nickel baths - Requirements and
DIN 50971 Electrodeposited coatings produced - chemicals for cyanide and / or alkaline baths - Requir DIN 50972 Electrodeposited coatings produced - copper sulfate for copper baths - Requirements and t DIN 50973 Electrodeposited coatings produced; Acids for electroplating baths; Requirements
DIN 50977 Measurement of coating thickness - Non-contact measurement of the thickness of layers o moving material to be Measured DIN 50978 Testing of metallic coatings; Adhesion of coatings produced by hot-dip galvanizing
DIN 50979 Metallic coatings - Electrodeposited zinc and zinc alloy coatings on ferrous materials with a -free treatment
DIN 50986 Measurement of coating thickness; Wedge cut method for measuring the thickness of pain coatings DIN 51001 Testing of oxidic raw and basic materials - General bases of work for X-ray fluorescence an DIN 51002 Inductively coupled plasma mass spectrometry (ICP-MS) Part 1: General principles and definitions DIN 51003 total reflection X-ray fluorescence analysis (TXRF) - General principles and definitions
DIN 51004 Thermal Analysis (TA); Determination of the melting of crystalline materials Temperatures thermal analysis (DTA) DIN 51005 Thermal Analysis (TA) - Definitions DIN 51006 Thermal Analysis (TA) - thermogravimetric (TG) - Basics DIN 51007 Thermal Analysis (TA), differential thermal analysis (DTA); Basics DIN 51008 Optical emission spectrometry (OES) - Part Part 1: Terms for systems with sparks and low pressure discharges Part 2 terms for systems with flames and plasmas DIN 51009 Optical Atomspektralanalyse - General principles and definitions DIN 51045 Determination of thermal expansion of solids Chapter 1 Basics Part 2 test fired fine ceramic materials using the dilatometer Part 3 test-fired fine ceramic materials using the dilatometer Part 4 testing of fired ordinary ceramic materials Part 5 test unfired ceramic materials ordinary DIN 51061 Testing of ceramic raw materials and Part 2 sampling of ceramic raw materials Part 3 sampling, Refractory bricks DIN 51081 Testing of oxidic raw and basic materials - Determination of mass change During annealing
DIN 51097 Testing of floor coverings; Determination of slip resistance; Naßbelastete barefoot areas; in Inclined plane DIN 51102 Testing of ceramic raw materials and Part 1 Determination of the acid resistance, method with lumpy test material for sewerage stoneware DIN 51103 Testing of ceramic materials; Determination of alkali resistance, test method with granular
DIN 51104 Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temp Determination of compressive strength
DIN 51105 Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temp Determination of bending strength double ring
DIN 51130 Testing of floor coverings - Determination of slip resistance - workrooms and work areas wi walking method - Ramp
DIN 51131 Testing of floor coverings - Determination of slip resistance - Methods for measuring the co friction
DIN 51175 Vitreous and porcelain enamels - Determination of thermo-mechanical properties by Mean methods DIN 51176 Vitreous and porcelain enamels - Preparation and characterization of errors Part 1 chemicals and equipment updates Part 2 thin film updates
DIN 51220 General Requirements for the materials testing machines and for verification and calibratio tensile testing machines ) DIN 51347 Testing of lubricants - Testing in the mixed friction with the Brugger lubricant tester Part 1 General working principles Part 2 method for lubricating oils DIN 51349 Testing of lubricants - Rating of Pistons from engine testing Part 1 General Part 2 petrol engines Part 3 diesel engines DIN 51350 Testing of lubricants - Testing in the four-ball tester Part 1 General working principles Part 2 Determination of welding load of liquid lubricants Part 3 Determination of wearing characteristics of liquid lubricants Part 4 Determination of welding load of consistent lubricants Part 5 Determination of wear characteristics for consistent lubricants Part 6 Determination of shear stability of polymer-Containing DIN 51351 Testing of lubricants - Determination of flocculation point of refrigeration oils with the press DIN 51352 Testing of lubricants; Determination of the aging behavior of lubricating oils Part 2 coke residue, Conradson after aging by passing air in the presence of iron (III) oxides DIN 51353 Testing of insulating oils; Detection of corrosive sulfur; Silver stripe audit
DIN 51360 Testing of cooling lubricants; Determination of the corrosion protection properties of waterfluids Part 1 Herbert corrosion test Part 2 chips / filter paper method DIN 51363 Testing of mineral oils - Determination of phosphorus content of lubricating oils and oil-age Part 2 Wavelength dispersive X-ray fluorescence analysis (XRF) Part 3 Direct determination by optical emission spectroscopy with inductively coupled plasma (ICP OE
DIN 51366 Testing of mineral oil hydrocarbons; Measurement of kinematic viscosity by Cannon-Fenske opaque liquids DIN 51367 Testing of cooling lubricants; Test of resistance to hard water emulsified coolants
DIN 51368 Testing of cooling lubricants; Determination of hydrochloric acid with separable proportion cutting fluids DIN 51369 Testing of metalworking fluids - Determination of pH value of water-mixed metalworking flu DIN 51371 Liquid fuels - Determination of thermal stability of fuel oil EL DIN 51375 Testing of lubricants - Determination of 1,2-ethanediol in engine oils Part 2 gas chromatographic method
DIN 51377 Examination of lubricating oils - Determination of the apparent viscosity of engine lubricati temperature between -5 ° C and -35 ° C - The Cold-Cranking Simulator DIN 51378 Testing of mineral oils; Determination of carbon distribution DIN 51380 Testing of lubricants; Determination of the light ends in used motor oils, gas chromatograp DIN 51385 Lubricants, Coolants; Terms DIN 51389 Testing of lubricants; Mechanical testing of hydraulic fluids in the vane pump Part 1 General working principles Part 2 A method for hydraulic fluids anhydrous DIN 51390 Testing of petroleum products - Determination of silicon content Part 2 Wavelength dispersive X-ray fluorescence analysis (XRF) Part 4 Direct determination by optical emission spectroscopy inductively coupled plasma (ICP-OES) DIN 51391 Testing of lubricants - Determination of additive elements Part 2 Wavelength dispersive X-ray fluorescence analysis (XRF) Part 3 Direct determination of Ca, Mg, Zn and Ba by optical emission with inductively coupled plasma DIN 51396 Testing of lubricants - Determination of wear elements Part 1 Direct determination by optical emission spectroscopy with inductively coupled plasma (ICP OE Part 2 Wavelength dispersive X-ray fluorescence analysis (XRF)
DIN 51398 Testing of lubricants; Determination of the apparent viscosity of gear oils at low temperatu viscometer (Flüssigkeitsbadmethode) DIN 51399 Testing of lubricants - Determination of elemental content of additives, wear and other Imp Part 1 Direct determination by optical emission spectroscopy with inductively coupled plasma (ICP OE DIN 51400 Testing of mineral oils and fuels - Determination of sulfur content (total sulfur) Part 1 General working principles Part 2 combustion by-Grote Krekeler; acidimetric titration; gravimetric determination Part 3 Schöniger combustion; Thorin III-Sulfonazo titration Part 4 combustion after Lingener procedures; titration Visual, Turbidimetric titration Part 7 microcoulometric deterministic mining oxidative process Part 10 Direct determination by optical emission spectroscopy with inductively coupled plasma (ICP O DIN 51401 atomic absorption spectrometry (AAS) - Definitions DIN 51402 testing of exhaust of oil burning Part 1 visual and photometric determination of soot Part 2 flux method for the detection of oil derivatives DIN 51403 Testing of liquid fuels Part 2 Determination of water demulsification of air-turbine fuels with the portable Mikroseparometer
DIN 51405 Testing of mineral oil hydrocarbons related fluids and Solvents for paints and varnishes - An chromatography - General working principles DIN 51408 Testing of mineral oil hydrocarbons - Determination of chlorine content Part 1 Wickbold combustion method Part 2 microcoulometric deterministic mining oxidative process DIN 51412 Testing of petroleum products - Determination of electrical conductivity Part 1 laboratory procedures Part 2 field method
DIN 51422 Testing of petroleum products - Gas chromatographic determination of the degree of purity 1 n-heptane part, iso-octane and Toluene Part 2 cetane and 1-methylnaphthalene DIN 51423 Testing of mineral oils Part 1 Measurement of the relative refractive index with the precision Part 2 Measurement of the relative refractive index with the Abbe refractometer
DIN 51425 Testing of petroleum hydrocarbons and related materials - Hochdruckflüssigchromatograph General working principles DIN 51426 Testing of fuel oil - Spectrophotometric determination of the red dye content in fuel oil
DIN 51430 Testing of fuel oil - Determination of red dye content and Solvent Yellow 124 in domestic fu light fuel oil with unmarked mineral - high performance liquid chromatography (HPLC) DIN 51435 Testing of petroleum products - Determination of boiling - Gas chromatographic method DIN 51436 Testing of petroleum products - Determination of freeze inhibitor in aviation turbine fuels spectrometry
DIN 51437 Testing of benzene and benzene homologues - Determination of non-aromatics, Toluene an benzene - Gas chromatography
DIN 51438 Testing of benzene and benzene homologues - Determination of thiophene in benzene - Ga DIN 51440 Testing of petrol - Determination of phosphorus content Part 1 Wavelength X-ray fluorescence analysis (XRF)
DIN 51444 Testing of petroleum products - Determination of bound nitrogen - combustion method with detector
DIN 51451 Testing of petroleum products and related products - Analysis by infrared spectrometry - G principles
DIN 51453 Testing of lubricants - Determination of oxidation and nitration of used motor oils - Infrared method DIN 51471 Liquid petroleum products - Determination of storage stability of fuel oil EL
DIN 51502 lubricants and related materials; Brief description of lubricants and marking of lubricant re and lubrication DIN 51503 Lubricants - Oils Refrigeration Part 1 Minimum Requirements Part 2 Used Refrigeration Oils
DIN 51506 Lubricants, Lubricating oils VB and VC and without additives and with additives and VDL lu Classification and requirements
DIN 51514 Testing of lubricants - Determination of the miscibility gap of refrigerator oil in the pressure Refrigerants method DIN 51515 Lubricants and governor fluids for turbines - Minimum requirements Part 1 turbine oils TD for normal thermal stress Part 2 turbine oils TG for higher temperature service DIN 51517 Lubricants - Oils Part 1 lubricant C; Minimum requirements Part 2 CL lubricating oils; Minimum requirements Part 3 oils CLP; Minimum requirements
DIN 51519 Lubricants - ISO viscosity classification for industrial liquid lubricants DIN 51520 Lubricants - Coolants - Neat cutting fluids SN; Minimum requirements DIN 51521 Lubricants - Metalworking fluids - Water cooling fluids SE; Requirements DIN 51522 heat transfer media Q - Requirements, testing, DIN 51524 hydraulic fluids - Hydraulic oils Part 1 hydraulic oils HL; Minimum requirements Part 2 HLP hydraulic oils; Minimum requirements Part 3 HVLP hydraulic oils; Minimum requirements DIN DIN DIN DIN
51528 51529 51531 51532
Testing of mineral oils and related products - Determination of thermal stability of unused h Testing of mineral oils and related products - inspection and assessment of used heat trans waxes - Determination of oil content waxes - Determination of melting point (cooling curve)
DIN 51535 Testing of petroleum products - Determination of the deposition tendency in turbochargers supercharged diesel engines DIN 51536 Testing of petroleum products - Determination of freeze inhibitor in aviation turbine fuels spectrometry DIN 51538 Testing of lubricants - Testing of refrigeration oils to ammonia resistance DIN 51558 Testing of mineral oils; Determination of neutralization number Part 1 color indicator titration Part 2 color indicator titration, insulating oils DIN 51559 Testing of mineral oils - Determination of saponification Part 1 saponification 2, Colour indicator titration Part 2 color indicator titration, insulating oils DIN 51562 Viscosity - measurement of kinematic viscosity using the Ubbelohde viscometer Part 1 Design and implementation of measurement Part 2 micro-Ubbelohde viscometer Part 3 Relative change in viscosity with short flow Part 4 viscometer and determination of the measurement uncertainty DIN 51563 Testing constant m DIN 51575 Testing DIN 51576 Testing DIN 51577 Testing
of mineral oils and related materials - Determination of the viscosity-temperature b of petroleum products - Determination of sulfated ash of mineral oil hydrocarbons - determination of salinity of mineral oil hydrocarbons and similar products
Part 4 Determination of chlorine and bromine content; Energy dispersive X-ray fluorescence analysis w spectrometers DIN 51580 Testing of Paraffine and waxes - Determination of cone penetration DIN 51581 Testing of petroleum products - Determination of evaporation loss Part 1. The method of Noack Part 2 gas chromatographic method DIN 51595 Testing of petroleum products - Determination of content of asphaltene - precipitation with
DIN 51599 Testing of lubricants - Determination of Demulgiervermögens (air release) after stirring me Replaced by DIN ISO 6614 DIN 51603 Liquid fuels - Fuel oils Part 1 fuel oil EL, minimum requirements Part 3, fuel oil, minimum requirements Part 4 fuel oils R, minimum requirements Part 5 Oil SA, minimum requirements DIN 51604-FAM test fluid Part 1 of polymer material; Composition and requirements Part 2 Methanolic for polymer materials; Composition and requirements Part 3 methanol-Containing subphase of polymer material; Composition and requirements DIN 51605 Fuels for vegetable oil engines - rapeseed oil fuel - Requirements and test methods DIN 51610 Testing of liquefied gases; Sampling DIN 51612 Testing of liquefied petroleum gas; Calculation of net calorific value DIN 51613 Testing of liquefied petroleum gas; Determination of elemental sulfur and the evaporation DIN 51614 Testing of liquefied petroleum gas; Qualitative test for ammonia, water and brine DIN 51618 Testing of liquefied petroleum gas; Calculation of the density at 15 ° C, 20 ° C and 50 ° C
DIN 51619 Testing of mineral oil hydrocarbons - Determination of composition of LPG - Gas chromatog special consideration of 1,3-butadiene with mass fractions of <= 0,1% (m / m) DIN 51622 liquefied gases, propane, propene, butane, butene, and Mixtures thereof; Requirements DIN 51624 Automotive fuels - gas - Requirements and test methods DIN 51625 Automotive fuels - ethanol fuel - Requirements and test methods DIN 51626 Automotive fuels - Requirements and test methods Part 1 E10 petrol DIN 51627 Automotive fuels - Methods of test
Direct determination of trace Part 6 elements in vegetable oils by optical emission with inductively co OES) DIN 51630 Special spirits - petroleum - Requirements DIN 51631 Special spirits - SPB spirits - Requirements DIN 51632 white spirits Part 1 Normal goods; Requirements and testing Part 2 deflavorized goods; Requirements and testing DIN 51633 benzene and benzene homologues - Requirements DIN 51634 Special spirits; Weather gasoline lamp; Minimum requirements DIN 51635 Special spirits - FAM-Normal petrol - Requirements DIN 51639 Testing of lubricants - Test methods Part 4 Determination of the vegetable oil fraction in used diesel motor oils by infrarotspektrometrische DIN 51640 Testing of liquefied petroleum gas; Calculating the vapor pressure at 40 ° C and 70 ° C DIN 51650 Testing of mineral oils and related products - Quantity Takeoff DIN 51700 Testing of solid fuels - General overview and test methods DIN 51701 Testing of solid fuels - Sampling and sample preparation Part 1 Definitions
Part 2 Implementation of Sampling Part 3 Execution of sample preparation Part 4 devices Part 5 Investigation of Precision DIN 51705 Testing of solid fuels - Determination of bulk density DIN 51717 Testing of solid fuels; Determination of the mechanical strength of coke DIN 51718 Testing of solid fuels - Determination of moisture content and moisture analysis DIN 51719 Testing of solid fuels - Determination of ash content DIN 51720 Testing of solid fuels - Determination of volatile matter DIN 51721 Testing of solid fuels - Determination of carbon and hydrogen - A method accor ding Radma DIN 51722 Testing of solid fuels - Determination of nitrogen content Part 1 semi-micro Kjeldahl method DIN 51723 Testing of solid fuels - Determination of fluorine content DIN 51724 Testing of solid fuels - Determination of sulfur Part 1 of total sulfur Part 2 species DIN 51725 Testing of solid fuels - Determination of phosphorus content DIN 51726 Testing of solid fuels - Determination of carbonate carbon dioxide DIN 51727 Testing of solid fuels - Determination of chlorine content DIN 51729 Testing of solid fuels - Determination of chemical composition of fuel ash Part 8 content of sodium and potassium oxide (Na 2 O, K 2 O) Part 10 X-ray fluorescence analysis (XRF) Part 11 Atomemissionsspektrometrische determination by inductively coupled plasma (ICP-OES) DIN 51731 Texture of wood pellets
DIN 51732 Testing of solid fuels - Determination of total content of carbon, hydrogen and nitrogen - In DIN 51733 Testing of solid fuels - Determination of elemental composition and calculation of the oxyg DIN 51734 Testing of solid fuels - proximate analysis and calculation of the carbon Shooting Up DIN 51735 Testing of solid fuels - Determination of plastic properties of coal with the Gieseler Plastom DIN 51750 Testing of mineral oils; Sampling Part 1 General Part 2 Liquids Part 3 ointment-like-consistent and solid materials
DIN 51755 Testing of mineral oils and other flammable liquids; Determination of flash point in a closed Pensky DIN 51756 Testing of petrol Part 1 Determination of knock characteristics (octane number); General Part 3 Determination of knock characteristics (octane number); Determination with the BASF test eng Part 7 Determination of knock characteristics (octane number) of alcohols and alcohol mixed fuels in t DIN 51757 Testing of mineral oils and related materials - Determination of density DIN 51761 Testing of benzene and benzene homologues - Determination of boiling nach Kraemer-Spilk DIN 51762 Testing of liquid fuels - Determination of sulfuric acid reaction
DIN 51769 Testing of petroleum products
Part 6 Determination of lead content (total lead) of petrol with a mass concentration of lead above 25 dispersive X-ray fluorescence analysis (XRF)
Part 9 Determination of lead content (total lead) of liquid petroleum hydrocarbons with a mass fractio 1000 mcg / kg, Iodmonochloridaufschluß; Extraction with Dithizone photometric and final destination DIN 51773 Testing of liquid fuels - Determination of ignition (cetane number) of Diesel fuels with the B DIN 51774 Testing of liquid fuels
Part 1 Determination of bromine acceptance after the electro metric dead stop method on samples wi acceptance than 0.5 g / 100 g (BA)
Part 2 Determination of bromine acceptance after the electro metric dead stop method on samples wi acceptance to 0.5 g / 100 g (BB) Part 3 Determination of bromine acceptance by the iodometric method (BC) DIN 51777 Testing of mineral oil hydrocarbons and Solvents; Determination of water content by Karl F Part 1 Direct method Part 2 Indirect method DIN 51790 Testing of liquid fuels - Determination of vanadium and nickel content
Part 4 Determination by atomic absorption spectrometry (AAS) or inductively coupled plasma optical e spectroscopy (ICP-OES) after ashing Part 7 X-ray fluorescence analysis using the fundamental parameter method DIN 51791 Testing of lubricants; Determination of additive elements Part 2 Wavelength dispersive X-ray fluorescence analysis (XRF) Part 3 Direct determination of Ca, Mg, Zn and Ba by optical emission with inductively coupled plasma DIN 51794 Testing of petroleum hydrocarbons - Determination of ignition temperature DIN 51797 Testing of liquid fuels Part 3 Determination of the sodium content, deterministic mining, by atomic absorption spectroscopy DIN 51798 Testing of liquid fuels - Determination of crystallization point of pure benzene DIN 51805 Testing of lubricants; Determination of flow pressure of lubricating greases, Kesternich met DIN 51818 Lubricants; Consistency classification for lubricating greases; NLGI grades DIN 51819 Testing of lubricants - Mechanical and dynamic test on the roller bearing lubricant test FE8 Part 1 General working principles
Part 2 methods for lubricating greases, to be employed test bearings, angular contact ball bearings or bearings Part 3 method for lubricating oil, to be used test bearing, Thrust cylindrical DIN 51820 Testing of lubricants; Infrared spectrometric analysis of lubricating greases Part 1 Recording and interpretation of infrared spectra DIN 51825 Lubricants - Lubricating greases K - Classification and requirements DIN 51828 Testing of lubricants and related products - Determination of the rapid biodegradability Part 1 General
DIN 51829 Petroleum products - Determination of additive and wear elements in greases - Wavelength fluorescence analysis DIN 51835 petroleum products Part 1 Determination of the oxidative stability of oils by measuring the chemiluminescence
Part 2 Determination of the oxidative stability of lubricating greases by measuring the chemiluminesc DIN 51851 Testing of gaseous fuels and other gases; Calculation of the Reduced volume of gas DIN 51853 Testing of fuel gases - Sampling DIN 51854 Testing of gaseous fuels and other gases; Determination of ammonia content DIN 51855 Testing of gaseous fuels and other gases - Determination of sulfur compounds Part 1 application, terms Part 4 content of hydrogen sulfide, zinc acetate method Part 6 content of hydrogen sulfide, mercaptan sulfur and sulfur-Kohlenstoffoxidsulfid; Potentiometric m
Gas chromatographic determination Part 7 of the content of sulfur-Containing odorants with electroch
Gas chromatographic determination of Part 8 Dihydrogensulfid, and other sulfur compounds Kohlensto specific detectors
DIN 51857 Gaseous fuels and other gases - Calculation of calorific value, density, relative density and gases and gas Mixtures DIN 51865 Testing of gaseous fuels and other gases - Determination of mercury content Part 1 chemisorption of atomic absorption spectrometry iodine (AAS) Part 2 combustion nach the modified method of Lingen; Atomic absorption spectrometry (AAS) Part 3 absorption in solutions, atomic absorption spectrometry (AAS) DIN 51866 temperature measurement Part 1 Overview of laser spectroscopic method Part 2 Rayleigh scattering and Raman
DIN 51869 Testing of gaseous fuels and other gases - Determination of water content by Karl Fischer -
DIN 51870 Testing of gaseous fuels and other gases; Determination of the density ratio after the weig calculation of the density
DIN 51871 Testing of gaseous fuels and other industrial gases; Determination of water vapor dew poin mirror DIN 51872 Testing of gaseous fuels and other gases; Determination of Constituents Gas chromatographic method Part 4 Capillary gas chromatographic method Part 5
DIN 51899 Gas analysis - measuring programs and evaluation methods for gas chromatography and o methods DIN 51900 Testing calorific value DIN 51901 Testing DIN 51902 Testing DIN 51903 Testing DIN 51904 Testing DIN 51905 Testing DIN 51906 Testing DIN 51907 Testing
of solid fuels and liquid - Determination of calorific value by the bomb calorimeter a of of of of of of of
carbon carbon carbon carbon carbon carbon carbon
materials materials materials materials materials materials materials
-
Determination Determination Determination Determination Determination Determination Determination
of of of of of of of
density nach Xylolverfahren - solids flexural strength by three point method - So ash value - solids moisture content - solids Verkokungsrückstandes; Binding and impreg Toluene-insoluble, Binding and impregnating density with liquid pycnometer - Binding and
DIN 51908 Testing of carbon materials - Determination of thermal conductivity at room temperature b method - solids
DIN 51909 Testing of carbon materials - Determination of linear thermal expansion coefficient - solids DIN 51910 Testing of carbon materials - Determination of compressive strength - solids
DIN 51911 Testing of carbon materials - Determination of the electrical resistivity nach the current-vol materials DIN 51912 Testing of carbon materials - Determination of hydrogen content - solids
DIN 51913 Testing of carbon materials - Determination of density by gas pycnometer (volumetric) usin measurement gas - solids DIN 51914 Testing of carbon materials - Determination of tensile strength - solids DIN 51915 Testing Solid materials DIN 51916 Testing DIN 51917 Testing DIN 51918 Testing
of carbon materials - Determination of the dynamic modulus of elasticity for the re of carbon materials - Determination of the tapped density; Solids of carbon materials - Rockwell hardness test - method with ball; Solids of carbon materials - Determination of bulk density and porosity open
DIN 51919 Testing of carbon method - Solid materials DIN 51920 Testing of carbon DIN 51921 Testing of carbon DIN 51922 Testing of carbon
materials - Determination of the electrical resistivity of the electrode afte
materials - Determination of the Mettler softening point - Binding and im materials - Determination of quinoline insolubles - Binding and impregna materials - Determination of ash value; Binding and impregnating
DIN 51925 Testing of carbon materials - Preparation of test specimens of carbonaceous ramming and bulk density - Binding and impregnating
DIN 51926 Testing of carbon materials - Determination of mesophases in binders by quantitative imag and impregnating DIN 51930 Testing of carbon materials - manufacture of extruded specimens from calcined cokes - sol
DIN 51935 Testing of carbon materials - Determination of coefficient of permeability after vacuum dec as the gas to be Measured; Solids
DIN 51936 Testing of carbon materials - Determination of thermal conductivity at High Temperatures a method - solids DIN 51937 Testing of carbon materials - Determination of degree of anisotropy; Solids DIN 51938 Testing of carbon materials - Determination of particle size distribution by sieving; Solids DIN 51940 Testing of carbon materials - Sampling and sample preparation - solids, solid binding and im DIN 51941 Testing of carbon materials - Determination of chemical composition Part 1: Preparation of test specimens, solids, solid binding and impregnating DIN 51942 Testing of carbon materials - Determination of dynamic Young's modulus by impulse excita DIN 51944 Testing of carbon materials - Determination of flexural strength by the four-point method DIN 51947 carbon materials - Vocabulary DIN 52005 Bitumen and bituminous binders - Determination of ash DIN 52006 Bitumen and bituminous binders - Methods of measuring the effects of water on binder coa Part 1 binder coating of bitumen emulsion Part 2 binder coating of cold bitumen Part 3 binder coating of penetration bitumen DIN 52007 Bitumen and bituminous binders - Determination of viscosity Part 1: General principles and evaluation DIN 52008 Natural stone test methods - Assessment of weathering resistance (eg rust resistance)
DIN 52009 Methods of test for aggregates - Determination of water absorption under pressure DIN 52034Testing of bituminous binder, in the detection of tar bitumen; January 2003 back without re Part 1 General Principles, apparatus, basic procedures Part 2 method with isoperibolem or static-jacket calorimeter Part 3 method with adiabatic jacket DIN 52108 Wear test accor ding Böhme, grinding wheel method DIN 52123 Testing of bitumen and polymer bitumen sheets DIN 52170 Determination of composition of hardened concrete Part 1 Framework, definitions, sampling, dry bulk Part 2 in hydrochloric acid and limestone and / or dolomithaltiger surcharge, sources are not available Part 3 hydrochloric acid supplement, source materials not available Part 4 Salzsäurelöslicher and / or -unlöslicher surcharge, source materials completely or Partially avail DIN 52184 Testing of wood; The swelling and shrinkage DIN 52185 Testing of wood; Determining the compressive strength parallel to the fiber DIN 52186 Testing of wood; Bending test DIN 52187 Testing of wood; Determination of shear strength in the fiber direction DIN 52188 Testing of wood; Determination of tensile strength parallel to the fiber DIN 52189 Testing of wood; Impact test Part 1 Determination of impact bending strength DIN 52210 Building acoustics testing - airborne and impact sound insulation Part 6 Determination of the bay level difference DIN 52230 Determination of burglary of safety glass for vehicle glazing - System Check
DIN 52240 testing of raw materials used in glass production; Chemical analysis of limestone with a mi carbonate Part 1 General information and test report Part 2 pulping process Part 3 Determination of silicon (IV) oxides Part 4 Determination of aluminum oxide Part 5 Determination of the total iron content, calculated is as iron (III) oxides Part 6 Determination of titanium (IV) oxide Part 7 Determination of manganese content calculated is as MnO Part 8 Determination of calcium oxide and magnesium oxide
DIN 52241 testing of raw materials used in glass production; Chemical analysis of dolomite Containing calcium magnesium carbonate Part 1 General information and test report Part 2 pulping process Part 3 Determination of silicon (IV) oxides Part 4 Determination of aluminum oxide Part 5 Determination of the total iron content, calculated is as iron (III) oxides Part 6 Determination of titanium (IV) oxide Part 7 Determination of manganese content calculated is as MnO Part 8 Determination of calcium oxide and magnesium oxide
DIN 52242 Testing of glass and glass raw materials - Determination of chloride DIN 52271 Testing of mineral fiber insulating materials; Behavior at higher Temperatures DIN 52274 Testing of mineral fiber insulating materials; pull-off; Determining vertical to the insulation DIN 52275 Testing of mineral fiber insulation materials Part 2 Determination of linear dimensions and density, pipe bowls DIN 52289 Road vehicles - Safety glazing materials for vehicle glazing - Test of resistance to chemical DIN 52298 Road vehicles - Measurement of the scattered light of safety glass for vehicle glazing Part 1 ring aperture method Part 2 image analysis method DIN 52305 Determination of the deflection angle and the refractive index of safety glass for vehicle gl DIN 52306 ball drop test on safety glazing materials for vehicle glazing DIN 52307 dart drop test on safety glazing materials for vehicle glazing DIN 52308 Boiling test on laminated glass DIN 52310 head form test on safety glazing materials for vehicle glazing DIN 52347 Testing of glass and plastic; Wear test; wheel method with scattered light measurement DIN 52367 particle board - Determination of shear strength parallel to the plane DIN 52376 Testing of plywood; Determination of compressive strength parallel to the plane DIN 52377 Testing of plywood; Determination of the train modulus of elasticity and tensile strength DIN 52450 Testing of inorganic non-metallic materials; Determination of shrinkage and swelling of sm DIN 52451 Testing of sealants for the construction industry Part 1 deterministic mining the change in mass and volume self-leveling sealants DIN 52452 Testing of sealants for building applications - Compatibility of sealants Part 2 Compatibility with chemicals Part 4 compatibility with coating systems DIN 52612 Thermal insulation evaluation; Determination of thermal conductivity with the disk device Part 2 follow-up of Measured values ??for building applications Part 3 thermal resistance of layered materials for building applications DIN 52613 Determination of thermal conductivity by the tube method DIN 52615 Determination of water vapor transmission, September 2001 Replaced by DIN EN ISO 1257
DIN 52980 Photocatalytic activity of Surfaces - Determination of photocatalytic activity by degradation DIN 53012 Viscosity - Newtonian liquids Capillary - Sources of error and corrections DIN 53014 Viscometry; Capillary with circular and rectangular cross-section for the determination of fl Part 1 Principles, concepts, terms, Part 2 Systematic Errors, Causes and corrections DIN 53015 Viscosity - measurement of the viscosity with the ball viscometer Hoeppler DIN 53017 Viscometry; Determination of the temperature coefficient of viscosity of liquids DIN 53019 Viscosity - Measurement of viscosities and flow curves by Means of rotational Chapter 1 Basics and measurement geometry Part 2 Viscometer and evaluation of measurement uncertainty Part 3 measurement errors and corrections
DIN 53100 Metallic coatings - Electrodeposited nickel-chromium and copper-nickel-chromium coatings DIN 53107 Testing of paper and board - Determination of Bekk smoothness DIN 53108 Testing of paper and board - Determination of roughness nach Bendtsen DIN 53109 Testing of paper and board - Determination of abrasion by the wheel method DIN 53114 Paper, board and pulps; Determining the conductivity of Aqueous extracts; ISO 6587: 1980 DIN 53115 Testing of paper - Tear test - Brecht Imset method DIN 53116 Testing of paper - Determination of fat permeability DIN 53118 Testing of paper and board - Determination of equilibrium moisture content in the stack or DIN 53119 Testing of paper - Determination of friction Part 1-recording procedures for data processing papers Part 2 Rutschwinkelprüfgerät DIN 53120 Testing of paper and board - Determination of air permeability Part 1 Mean air permeability Bendtsen Part 2 methods for mean air permeabilities Schopper DIN 53121 Testing of paper and board - Determination of bending stiffness by the beam method
DIN 53122 Testing of plastics and elastomer films, paper, cardboard and other sheet materials - Deter vapor permeability Part 1 Gravimetric method DIN 53123 Testing of paper and board - Determination of bending stiffness Part 1 resonance length method DIN 53124 Paper, board and pulps - Determination of pH in Aqueous extracts DIN 53125 Testing of paper and board - Determination of chloride content in Aqueous extracts DIN 53126 Testing of paper and board - Determination of writability with ink DIN 53127 Testing of paper and board - Determination of water-soluble sulfates in paper and cardboar DIN 53129 Testing of Solid Board - water absorption and thickness swelling, water storage DIN 53131 Testing of paper - Inkjet Media Part 1 Cockle Part 2 drying time Part 3 image quality - optical resolution, optical density, color values, print image disturbances DIN 53133 Testing of board - Determination of water resistance of the bond of corrugated cardboard DIN 53134 Testing of paper and board - Determination of the ring crush resistance DIN 53142 Testing of board - penetration test Part 1 test with the pendulum impact tester Part 2 examination with a linear feed DIN 53145 Testing of paper and board - Measurement Principles for deterministic mining the reflection Part 1 Measurement of non-fluorescent samples Part 2 measurement of fluorescent samples DIN 53146 Testing of paper and board - Determination of opacity DIN 53147 Testing of paper; Determination of transparency DIN 53160 Determination of color transmittance of everyday objects Part 1 test with artificial saliva
Part 2 examination with sweat
DIN 53163 Testing of pigments and fillers; Determining the brightness of extenders and white pigmen
DIN 53164 Testing of pigments and fillers; Determination of relative scattering power of white pigmen processing
DIN 53165 Testing of pigments and extenders - Determination of relative scattering power of white pig pigment volume concentration (PVC) - gray paste method DIN 53170 Solvents for paints and varnishes - Determination of evaporation rate DIN 53171 Solvents for paints and varnishes - Determination of distillation characteristics (boiling and DIN 53172 Solvents for paints and varnishes - Determination of evaporation residue DIN 53173 Solvents for paints and varnishes - Determination of carbonyl
DIN 53175 Binders for paints and coatings; Determination of the solidification point of fatty acids (me Dalican) DIN 53176 Binders for paints and varnishes - Determination of amines number of water-dilutable bind
DIN 53177 connector for coatings - Measurement of dynamic viscosity of liquid resins, resin solutions isosceles Ubbelohde type DIN 53178 Testing of paints; Determination of the content of nitrocellulose lacquers DIN 53181 Binders for paints and coatings; Determination of the melting range of resins nach the cap DIN 53184 Binders for paints and varnishes - Unsaturated polyester - Testing
DIN 53195 Testing of pigments; Determination of residue on sieve with water as washing liquid (manu 2010 Replaced by DIN EN ISO 787-7 DIN 53206 Testing of pigments; Particle size analysis Part 1 Basic Concepts
DIN 53215 Bitumen and bituminous binders - Determination of non-volatile components of bituminous DIN 53219 Paints and varnishes - Determination of the volume of non-volatile fractions DIN 53221 Paints and varnishes - tests of coatings on Recoatability DIN 53235 Testing of pigments - Tests on standard color deep samples Part 1 standard color depths Part 2 set of samples on standard depth
DIN 53236 Testing of coloring materials; Measurement and evaluation conditions for the determinatio for paint, similar coatings and plastics DIN 53240 Determination of hydroxyl Part 1 procedure without Catalyst Part 2 process with Catalyst DIN 53241 Determination of iodine value Part 1 method with Wijs solution DIN 53245 Solvents for paints and varnishes - Alcohols - Supply specification, Further requirements an DIN 53281 Testing of adhesively bonded joints - Sample Preparation DIN 53287 Testing of metal adhesives and metal joints - Determination of resistance to liquids DIN 53290 Testing of sandwiches; Terms DIN 53291 Testing of sandwiches; Pressure test perpendicular to the faces DIN 53292 Testing of sandwiches; Tensile test perpendicular to the faces
DIN DIN DIN DIN DIN
53293 53294 53295 53316 53323
Testing Testing Testing Testing Testing
of of of of of
sandwiches; Bending test sandwiches; Shear test sandwiches; drum peel test leather - Detection of azo dyes in leather Certain leather; Determination of the stress-strain behavior in Wölbversuch
DIN 53325 Testing of leather; ball pressure test for the evaluation of Narbendehnfähigkeit and breakin Lastometer DIN 53340 Testing of leather; Determination of the duration-folding behavior of stiff leathers DIN 53342 Testing of leather; Determination of iron fastness been directed Leather DIN 53344 Testing of leather; Determination of the hydrolytic stability of finished and not finished leat DIN 53345 Testing of leather fatliquoring agents; Analytical Methods Part 1 Sampling Part 2 Identification of ionic charge Part 3 Determination of water-soluble and water Solvents Part 4 Determination of steam-volatile, water-immiscible Solvents Part 5 Determination of fatty substances and minerals Part 6 Determination of pH in Aqueous emulsion or solution Part 7 Determination of residual fat content of Lickerflotten Part 8 test electrolyte stability DIN 53346 Testing of Pelzfettungsmitteln; Analytical method; Examination electrolyte stability DIN 53350 Testing accor ding Ohlsen DIN 53356 Testing DIN 53357 Testing DIN 53359 Testing
of plastic films and plastic textile fabrics topcoated; Determination of the bending s of artificial leather and similar sheet materials; Tear test of plastics and foils; Adhesion test of artificial leather and similar sheet materials - Flex cracking test
DIN 53360 Testing of artificial leather and similar sheet materials; Determination of total elongation (S and permanent elongation
DIN 53362 test of plastic films and textile fabrics (except non-woven fabrics), with or without a coverin determination of flexural rigidity - A method nach cantilever DIN 53363 Testing of plastic films - Tear test using trapezoidal test specimen with incision DIN 53366 Testing of plastic films and plastic sheeting - Determination of blocking force DIN 53369 Testing plastic foils; Determination of shrinkage force DIN 53370 Testing of plastic films - Determination of thickness by mechanical scanning DIN 53377 Testing of plastic films - Determination of dimensional change DIN 53380 Testing of plastics - Determination of gas permeability Part 1 Volumetric method for testing of plastic films Part 2 Manometric method for testing of plastic films Part 3 Specific oxygen carrier gas method for testing of plastic films and plastic Molding
Part 4 Kohlenstoffdioxidspezifisches infrared absorption method for the measurement of plastic films a DIN 53381 Testing of plastics; Determination of thermodynamic stability of polyvinyl chloride (PVC) Dehydrochlorination Part 1
DIN 53383 Testing of plastics; Testing the oxidation stability by oven aging, high density polyethylene Part 2 Infrared spectroscopic (IR) Determination of carbonyl content DIN 53390 Testing of glass fiber reinforced plastics; Bending test on unidirectional glass fiber reinforce DIN 53393 Testing of glass fiber reinforced plastics; Behavior When exposed to chemicals
DIN 53394 Testing of plastics; Determination of monomeric styrene in the reaction resin molded mate Unsaturated polyester resins, methods using Wijs solution Part 2 Testing of Plastics; Determination of monomeric styrene in the reaction resin molded materials Unsaturated polyester resins; Gas chromatographic method DIN 53399 Testing of fiber reinforced plastics Part 2 Shear test on flat specimens DIN 53400 Testing of Plasticizers; Determination of physical and chemical parameters of Plasticizers
DIN 53402 Determination of the acid number of heavy fuel oils and lubricating oils, June 1998 Replace 3682 DIN 53408 Testing of plastics; Determining the dissolution temperature of polyvinyl chloride (PVC) in P
DIN 53419 Extruded profiles of hard polyvinyl chloride (PVC hard); Behavior with methylene chloride ( test) DIN 53428 Testing of Foams; Determination of the effect liquids, vapors, gases and solids DIN 53435 Testing of plastics; bending test and impact test specimens on Dynstat DIN 53436 Generation of thermal decomposition products from materials in air stream for toxicologica Part 1 decomposition apparatus and determination of test temperature Part 2 thermal decomposition method Part 3 methods for inhalation toxicity Part 4 process for the thermal decomposition of liquids Part 5 method for deterministic calculations to mine the toxicity DIN 53438 Testing of combustible materials; response to ignition by a burner Part 1: General Information Part 2 edge exposure Part 3 surface exposure DIN 53442 Testing of plastics; Fatigue test in the bending area of flat specimens DIN 53452 bending test DIN 53455 Testing of plastics; tensile test May 1996 Replaced by DIN EN ISO 527-1 ... 3 DIN 53463 Testing of plastics; Fatigue test in the bending area of flat specimens
DIN 53464 Testing of plastics; Determination of Shrinkage Properties of Preßstoffen from hot-curable m DIN 53465 Testing of plastics; Determining the closing time for curable molding compounds
DIN 53470 Testing of molding compounds; press tool for the production of standardized samples from compounds DIN 53474 Testing of plastics, rubber - Determination of chlorine content (digestion Wickbold) DIN 53477 Testing of plastics; Determination of particle size distribution of molding materials by dry-s DIN 53479 Determination of density DIN 53483 Testing of Insulating Materials; Determination of Dielectric Properties Part 1 Definitions, General Information
Part 2 examination at the specified frequency of 50 Hz, 1 kHz, 1 MHz Part 3 measuring cells for fluids for frequencies up to 100 MHz
DIN 53497 Testing of plastics; hot storage experiment on molded parts from thermoplastic molding Co external mechanical impacts DIN 53498 Testing of plastics; storage of hot stampings from curable molding compounds DIN 53504 Testing in a tensile test DIN 53506 Testing DIN 53508 Testing DIN 53512 Testing
of rubber - Determination of tensile strength, tensile strength, elongation at break of rubber and elastomers; Determination of needle tear of rubber and elastomers - Artificial aging of rubber - Determination of rebound resilience (Pushed swing)
DIN 53513 Testing of rubber and elastomers; determination of the visco-elastic properties of elastome vibrations outside the resonant DIN 53523 Testing of rubber and elastomers; Examination with the shear disc viscometer Mooney Part 2 requests to the device Part 3 Determination of Mooney viscosity Part 4 Determination of the Scorching Behaviour DIN 53529 Testing of rubber and elastomers; Vulcametry Part 1 General working principles Part 2 Determination of reaction kinetic analysis of Vulkanisationsverlaufes and Vernetzungsisotherme Part 3 Determination of the crosslinking behavior rotor with loose Vulkametern Part 4 Determination of the cross-linking behavior with a rheometer with rotor DIN 53530 Testing of organic materials; separation test at adhesively joined to fabric layers DIN 53531 Testing of rubber and elastomers; Determination of adhesion to rigid materials Part 2 examination between cylinders with conical ends
DIN 53533 Testing of rubber and elastomers; Checking Heat education and Life During the fatigue tes (Flexometerprüfung) Chapter 1 Basics Part 2 rotary flexometer Part 3 compression flexometer DIN 53535 Testing of rubber and elastomers; Foundations for dynamic test procedure DIN 53536 Testing of rubber and elastomers; Determination of gas permeability DIN 53543 Testing of semi-rigid polyurethane (PUR) Integral; material for shoe soles and parts
DIN 53545 Testing of rubber and elastomers; Determining the behavior of elastomers at low Temperat Fundamentals, Methods of test
DIN 53548 Testing of rubber and elastomers; Determination of Einfrierverhaltens of elastomers with m measurements (Gehman test) DIN 53552 Testing of carbon blacks; Determination of Volatile Constituents During the annealing of ca DIN 53579 Testing of Flexible Foams - indentation test on finished parts DIN 53583 Testing of pigments - Determination of fines and abrasion of beaded pigment blacks DIN 53598 Part 1 Statistical analysis of samples with examples from elastomers and plastics testing DIN 53704 Testing of plastics; Determination of free phenol in phenolic Moldings
DIN 53728
Part 3 Testing of Plastics; Determination of the viscosity of polyethylene terephthalate (PETP) or polyb terephthalate (PBTP) in dilute solution DIN 53733 Testing of plastics; Reduction of Plastic Products for Test Purposes
DIN 53741 Testing of plastics; Determination of volatile aromatic hydrocarbons in polystyrene, gas chr method
DIN 53742 Testing of plastics; Determining the content of vinyl acetate copolymer of vinyl chloride an infrared spectrographic method DIN 53743 Testing of plastics; Gas chromatographic determination of vinyl chloride (VC) in polyvinyl c DIN 53746 Testing of plastics; Proof of polyamide DIN 53748 Chemical analysis of phenol-formaldehyde resins, phenolic molding compounds and Mould DIN 53752 Testing of plastics; Determination of the coefficient of thermal expansion DIN 53754 Testing of plastics; Determination of abrasion on the friction wheel DIN 53765 Testing of plastics and elastomers; Thermal analysis; differential scanning calorimetry (DSC DIN 53766 Testing of equipment and containers made of glass fiber reinforced plastics Part 1 Determination of bond strength Stirnzugversuch DIN 53769 Testing of pipes made of glass fiber reinforced plastics Part 1 Determination of adhesive shear strength of pipeline components CORRESPONDING pipe type B Part 2 resistance to internal pressure tests on pipes Part 3 short-term and long-term stiffness test on pipes Part 6 internal pressure Schwellversuche of pipes and pipe components DIN 53770 pigments and extenders - Determination of soluble in hydrochloric acid Part 1 Preparation of acid extracts Part 2 content of antimony Part 3 content of arsenic Part 4 barium content Part 5 content of lead Part 6 of cadmium Part 7 chromium content Part 8 content of chromium (VI) Part 9 of cobalt Part 10 copper content Part 11 of manganese Part 12 nickel content Part 13 of mercury Part 14 levels of selenium Part 15 of zinc Part 16 Determination of 12 elements by inductively coupled plasma atomic emission spectrometry DIN 53771 Testing of coloring materials in plastics; Determination of resistance of coloring materials t DIN 53778 abrasion resistance of colors DIN 53779 Determination of electrical conductivity and the electrical resistivity of Aqueous extracts DIN 53780 pigments and extenders - Determination of water-soluble components - content of chromiu
DIN 53781 Paints and varnishes - Methods of test for resistance of coatings against ionizing radiation DIN 53800 Textiles - Determination of commercial mass Part 1 Determination of dry matter by drying in a stream of hot air Part 2 Determination of the mass trade and trade fineness DIN 53803 Sampling Part 1 statistical principles of sampling with simple division Part 2 Practical implementation Part 3 statistical principles of sampling with cross classification nach two equal point of Part 4 statistical principles of sampling with cross classification nach two hierarchical criteria DIN 53804 Statistical evaluations Part 1 Continuous Features Part 2 countable (discrete) features Part 3 Ordinal Part 4 attribute characteristics DIN 53805 Testing of textiles; Determination of length of fibers, concepts and general principles DIN 53806 Testing of textiles; Determination of fiber length of cotton nach the crest of a batch process DIN 53808 Testing of textiles - Determination of length of fibers Part 1 single fiber measurement method DIN 53811 Testing of textiles; fiber diameter measurement in micro projection of the longitudinal view DIN 53814 Testing of textiles; Determination of the water retention capacity of fibers and yarn cutting DIN 53815 Testing of textiles; Terms for the simple tensile test DIN 53818 Testing of textiles - Error in spun yarns and twisted yarns and primary products - Vocabular DIN 53829 Testing of textiles; Determining the regularity of threads Part 1 examination of power and length on a moving test, basics DIN 53830 Testing of textiles; Determination of fineness of yarns and threads Part 3 Simple and plied yarns, textured yarns; section method Part 4 elasto Including wrap yarn from elastofibers; section method DIN 53834 Part 2 Testing of textiles; Simple tensile test on yarns and threads in the oven-dry condition DIN 53835 Testing of textiles; determination of the elastic behavior Chapter 1 Basics Part 2 yarns and plied Elastomeric repeated tensile load between constant extension limits Part 3 yarns and threads, single strain between constant extension limits Part 4 Yarns and twists, single strain between constant force limits Part 13 Textile fabrics, single strain between constant extension limits Part 14 of knitted fabrics, single strain between two force limits DIN 53840 Testing of textiles; Determination of textured filament yarns of Kräuselkennwerten Part 1 dtex filament yarns with a linear density to 500 Part 2 filament yarns having a linear density over 500 DIN 53842 Testing of textiles Part 1 knot tensile test for single and plied yarns
DIN 53843 Testing of textiles Part 1 Schlingenzugversuch; Yarns Part 2 Schlingenzugversuch of textile fibers DIN 53852 Testing of textiles; Determination of Garnlängenverhältnissen in woven and knitted fabrics DIN 53856 Testing of Textiles - Determination of the mass fractions of warp and weft DIN 53859 Testing of textiles; Tear test fabrics Part 5 Trapezoidal Tear test DIN 53860 Testing of textiles; Examining the Ausbeulneigung of textile fabrics Part 1 elbow method, static load DIN 53861 Testing of textiles Part 3 camber-changing and burst test, tables for test evaluation DIN 53863 Testing of textiles Part 1 abrasion tests of textile fabrics, General Part 2 scrubbing tests of textile fabrics, rotary abrasion test DIN 53864 Testing of textiles; Determination of the bending stiffness method accor ding Schlenker DIN 53865 Testing of Textiles - Determination of fiber migration tendency - Tumbler method DIN 53866 Testing of textiles; Shrinkage behavior of yarns and threads Part 4 Determination of Shrinkage WITHDRAWN into vapor without replacement Part 12 Determination of shrinkage force in gaseous and liquid media; section method
DIN 53867 Testing of textiles; Determination of pilling; Examination under the flapping wing process ( pilling tester) DIN 53902 Testing of surfactants, foaming power of determination Part 1 perforated disks impact method, January 2000 Replaced by DIN EN 12728 Part 2 Modified Ross-Miles method DIN 53923 Testing of textiles; Determination of water absorption of textile fabrics DIN 53924 Testing of Textiles - Determination of wicking textile fabrics to water (capillary rise method
DIN 53930 Testing of textiles; Determination of resistance of textiles against damage caused by micro and sample pretreatment DIN 53931 Testing of textiles; Determination of resistance of textiles against mold, mold test DIN 53941 Testing of Textiles - Determination of micronaire value of cotton fibers DIN 53943 Testing of textiles; maturity of cotton fibers Part 1 Definitions Part 2 Determination of the degree of ripeness, microscopic method, swelling with sodium hydroxide DIN 53944 Testing of textiles; Determination of clamping length and uniformity factor of cotton DIN 53978 tetrachloro ethylene (Perchlorethylene) - Requirements and tests DIN 54005 Test for color fastness of textiles; Determination of water fastness of dyeings and prints (m
DIN 54015 Test for color fastness of textiles; Withdrawn determination of the peroxide wash fastness o without replacement
DIN 54016 Test for color fastness of textiles; Withdrawn determination of hypochlorite wash fastness o without replacement
DIN 54034 Test for color fastness of textiles; Determination of hypochlorite bleach fastness of dyeings
DIN 54046 Test for color fastness of textiles; Colour fastness to chlorination wool
DIN 54056 Test for color fastness of textiles; determination of color fastness of dyeings and prints to s storage
DIN 54113 Non-destructive testing - Radiation protection rules for the technical application of X-ray eq Part 1 General safety requirements Part 2 Safety requirements and testing for manufacturing, construction and operational
Part 3 formulas and diagrams for calculation of radiation protection for X-ray equipment up to a tube v
DIN 54115 Non-destructive testing - Radiation protection rules for the technical application of sealed r Part 1 Stationary and non-stationary variable handling in the gamma radiography Part 3 Organisation of radiation protection During handling and transport of gamma radiography Part 4 production and testing of portable radiation devices for gamma radiography Part 5 Bautechnische radiation protection arrangements for Gammaradiografie Part 6 inspection, maintenance and functional testing of radiation devices in the gamma radiography
Part 7 Storage of radioactive sources - Requirements for storage devices and Their installation facilitie and theft protection DIN 54123-destructive testing; Ultrasonic method for testing of welding, rolling and explosion DIN 54130-destructive testing; Magnetic flux leakage method, General DIN 54136-destructive testing; Magnetic Streuflußprüfung with scanning probes Chapter 1 Basics DIN 54140-destructive testing; Inductive method Part 3 Presentation and general properties of coil system DIN 54141-destructive testing; Eddy current testing of pipes Part 1 General information on testing with through coils after the Einfrequenzmethode Part 2 control method for deterministic mining the properties of eddy current testing of system with co Part 3 Performance of eddy current testing DIN 54145 Non-destructive testing - Electromagnetic detection method Part 1 Passive Magnetic Part 2 Active electromagnetic induction method DIN 54150-destructive testing; Impression methods for surface examination (Replica-technique) DIN 54161 Non-destructive testing - Qualification of NDT Prüfwerkern
DIN 54162 Non-destructive testing - Qualification and certification of personnel for thermo graphic tes special bases for level 1, 2 and 3 DIN 54180 Non-destructive testing - shearography Part 1 General principles Part 2 devices DIN 54190 Non-destructive testing - Thermographic testing Part 1 General principles Part 2 devices Part 3 terms
DIN 54191 Non-destructive testing - Thermographic inspection of electrical equipment DIN 54192 Non-destructive testing - Active thermography
DIN 54204 Testing of textiles; Quantitative analysis of binary Mixtures, wool with other fibers, potassiu solution method DIN 54209 Testing of textiles; Quantitative analysis of binary Mixtures, degummed mulberry silk with zinc chloride method DIN 54212 Testing of textiles; Quantitative analysis of binary Mixtures, casein fibers with other fibers,
DIN 54221 Testing of textiles; Quantitative analysis of binary Mixtures, polyamide 6 6 or polyamide 6 fibers, hydrochloric acid method DIN 54231 Textiles - Detection of disperse dyes DIN 54232 Textiles - Determination of the content of compounds on the basis of chlorobenzene and ch DIN 54233 Testing of Textiles - Determination of metals Part 1 Determination of metals using microwave digestion Part 2 Determination of extractable metals with hydrochloric acid Part 3 Determination of extractable metals with acid synthetic perspiration solution Part 4 Determination of extractable metals with synthetic saliva solution DIN 54270 Testing of textiles; Determination of the intrinsic viscosity of celluloses Chapter 1 Basics Part 2 cueing method Part 3 EWNN mod (NaCl) method DIN 54274 Testing of textiles; Quantitative determination of the amino terminal groups in polyamide fi DIN 54275 Testing of textiles; Determination of pH of fibrous material, extrapolation DIN 54278 Testing of textiles - Coatings and attendant materials Part 1 Definition of the soluble substances in organic Solvents DIN 54279 Testing of textiles; Determination of urea / bisulphite solubility of wool DIN 54280 Testing of textiles; Determination of acidity of wool DIN 54281 Testing of textiles; Determination of alkali solubility of wool DIN 54282 Testing of textiles; Determination of the acetic acid content in acetate or triacetate DIN 54285 Testing of textiles; Determination of size content DIN 54286 Testing of textiles; Determination of Cysteinsäuregehaltes in Wollhydrolysaten DIN 54287 Testing of textiles; Determination of the alkali content of wool DIN 54288 Testing of textiles; Quantitative determination of sulfur in viscose fibers
DIN 54289 Testing of surfactants and textile auxiliaries; Testing the effect of dyeing polyester textile d for disperse dyes with Part 1 examination of the accelerating effect Part 2 Determination of the achievable color yield
DIN 54290 Testing of surfactants and textile auxiliaries; Testing the effect of leveling agents in the dye textile disperse dyes with under high-temperature conditions Part 1 examination of Migrierwirkung Part 2 examination of the restraining effect Part 3 examination of the braking effect DIN 54295 Textile dyeing - Vocabulary
DIN 54310 Testing of textiles; Separation of fixed interlining fabric's outer fabric, Mechanical separatio DIN 54332 Testing of textiles; Determination of burning behavior of textile floor coverings DIN 54333 Testing of textiles; Determination of burning behavior; Horizontal method Part 1 ignition edge exposure DIN 54334 Testing of textiles; Determination of burning behavior, ignition timing to on edge DIN 54335 Testing of textiles; Determination of burning behavior, 45 ° method, ignition edge exposure DIN 54341 testing seats for rail vehicles for public transport; Determination of burning behavior with a DIN 54345 Testing of textiles; Electrostatic behavior Part 1 Determination of electrical resistance values Part 3 Instrumental determination of charging textile floor coverings Part 4 Determination of the electrostatic charging of textile fabrics Part 5 Determination of electrical resistance in strips of textile fabrics DIN 54355 Testing of pulp; Determination of resistance of pulp against sodium hydroxide solution (alk DIN 54356 Testing of pulp; Determination of alkali solubility of pulp DIN 54357 Testing of pulp; Determination of Kappa Number DIN 54360 Pulps - Laboratory beating - Jokro mill process DIN 54361 Testing of pulp; Determination of Pentosangehaltes, furfural method
DIN 54363 Testing of pulp and paper; Determination of levels of iron, manganese, copper, calcium and determined by atomic absorption spectroscopy (AAS) DIN 54370 Testing of paper and board - Determination of residue on ignition DIN 54372 Testing of pulp and paper; Determination of calcium and magnesium content; Titrimetric d DIN 54373 Testing of pulp, paper and paperboard; Determination of acid-insoluble fraction in the Resid DIN 54377 Testing of pulp and paper; Determination of the content of silicon (IV) oxides Part 1 Gravimetric method Part 2 Photometric method DIN 54378 Testing of paper and cardboard; Determination of surface colony count (OKZs) DIN 54379 Testing of paper and cardboard; Determination of the total colony count (TVC) DIN 54383 Testing of paper and cardboard; Determination of clostridial spores
DIN 54386 Testing of paper, board and pulps; Photometric Determination of copper content with batho Determination by nitric acid digestion DIN 54400 Ion exchange - Terminology DIN 54401 Testing of ion exchangers - Sampling DIN 54402 Testing of ion exchangers - Determination of total capacity of anion exchangers DIN 54403 Testing of ion exchangers - Determination of total capacity of cation DIN 54406 Testing of ion exchangers - Determination of resistance to osmotic and hydro mechanical s DIN 54407 Testing of ion exchangers - Determination of particle size distribution DIN 54408 Testing percentage DIN 54410 Testing DIN 54413 Testing DIN 54455 Testing DIN 54456 Testing
of ion exchangers - Determination of bulk density, moisture content and the equilib of of of of
ion exchangers - Determination of density ion exchangers - Determination of water-extractable organic carbon metal adhesives and metal joints; Torsionsscher trial structural adhesives and -klebungen - Air resistance test
DIN 54457 Structural adhesives - Testing of adhesive bonds - Tracked peel test
DIN 54458 Structural adhesives - Determination of flow and application behavior of viscoelastic adhes oscillation rheometry DIN 54459 Structural adhesives - Testing of adhesive bonds - Manufacture of lapshears coil coated ste DIN 54461 Structural adhesives - Testing of adhesive bonds - Bending peel test
DIN 54500 Testing of paper - Determination of density-related light scattering and light absorption coe papers
DIN 54514 Testing of paper and board - Determination of initial wet strength (Initial Wet Web Strength DIN 54515 Testing of paper and board - Determination of water repellency DIN 54516 Testing of paper and board - Determination of resistance gap DIN 54517 Testing of paper and board - Determination of wet expansion DIN 54518 Testing of paper and board - strip crush resistance DIN 54519 Testing of board - Determination of edgewise crush resistance of solid board DIN 54530 Paper and board - Testing of cores from core board Part 10 Determination of roughness DIN 54540 Testing of hygiene products - Tissue and nonwoven Part 5 Determination of wet expansion Part 9 Determination of moisture content DIN 54600 Testing of paper and cardboard; Testing for antimicrobial additives Part 1 Determination of disulfide tetramethyl thiuram disulfide (TMTD) Part 8 Determination of methylene-bis-thiocyanate DIN 54603 Testing of paper and board - Determination of the content of glyoxal DIN 54604 Testing of paper and cardboard; Determination of strength Part 1 Enzymatic determination of native starch DIN 54605 Testing of pulp, paper and paperboard; AAS Determination of cadmium DIN 54800 Testing of plastics; Production of polyvinylchloride (PVC) pastes for test purposes
DIN 54801 Testing of plastics; Determination of the apparent viscosity at high shear rates of polyvinyl pastes with the capillary viscometer Severs
DIN 54802 Testing of plastics - Determination of plasticizer absorption and plasticizer absorption rate vinyl chloride (VC) polymer Part 1 planetary mixer method Part 2 Static method DIN 54811 Testing of plastics; Determination of the flow behavior of polymer melts with a capillary rhe
DIN 54813 Testing of plastics; Examination of bundles of textile glass-reinforced thermosetting plastic tensile strength in bending shear tests DIN 54815 pipes from filled polyester resin molding material Part 1 dimensions, material, marking Part 2 requirements, testing DIN 54836 Testing of combustible materials; Determination of ignition temperature
DIN 54837 Testing of materials, components and component sections for rail vehicles - Determination using a gas burner
DIN 54841 warning device made of plastic for buried cables and pipelines Part 3 Detectable track tape Part 5 cable cover DIN 55003 Graphical symbols for NC machine tools, retired without replacement DIN 55058 spindle heads for adjusting sleeves; Connecting dimensions DIN 55170 single-column table eccentric presses; Sizes DIN 55181 machine tools; Mechanical sided presses, single acting with nominal forces from 400 kN to
DIN 55184 machine tools; Mechanical C-frame presses, installation space for tools, Sizes, mounting pl inlaid rings DIN 55185 machine tools; Mechanical double column presses with nominal speed almost forces from Sizes
DIN 55189 machine tools; Determination of characteristic values ??for stamping of sheet metal proces Part 1 Mechanical Presses Part 2 Hydraulic presses DIN 55200 machine tools; T-groove spacing; Mass DIN 55201 machine tools; Pallets for machine tools Part 1 nominal sizes up to 800 mm; Form A Part 2 nominal sizes from 1000 mm, Form B DIN 55301 design of statistical tables DIN 55303 Statistical analysis of data DIN 55350 terms of quality and statistics Supplement 1, structure and overall index Part 11 terms of quality management Part 12 feature related terms and definitions Part 13 terms of the accuracy of investigation and determination of results Part 14 terms of sampling Part 15 keywords for patterns
Part 16 terms of quality assurance; Terms Relating to quality assurance systems (draft), October 1989 without replacement Part 17 terms of the quality inspection types Part 18 concepts Relating to certificates on the results of quality inspections; Quality inspection certifi Part 21 concepts of statistics, random variables and probability distributions Part 22 concepts of statistics, probability distributions Special Part 23 concepts of statistics; Descriptive Statistics Part 24 concepts of statistics; Inferential statistics Part 31 concepts of acceptance sampling Part 33 terms of statistical process control (SPC) Part 34 limit of detection, limit of detection and detection capability, September 2004 Replaced by DIN DIN 55402 marking for shipment of packages Part 2 Guideline for export packing DIN 55405 Packaging - Terminology - Terms
DIN 55406 Packaging - Special Technical delivery and subscription and conditions of use for one- or tw screw caps made of polyethylene (PE) and polypropylene (PP) and 28 mm closure system made of alu DIN 55407 of packaging - General technical delivery and purchase conditions (ATLB) Part 2 error catalog DIN 55409 Packaging - Test method for the determination of opening forces on peelable packaging Part 1 Flexible Packaging Part 2 Rigid Packaging DIN 55423 transport chain for meat and meat products Part 1 Rigid, stackable reusable transport and storage bins made ??of plastic, Dimensions, weights, de Part 2 Rigid, stackable reusable transport and storage bins made ??of plastic; Requirements and tests Part 5 range of polyethylene, 800 mm × 1200 mm × 160 mm; Dimensions, weights Part 6 range of polyethylene, 800 mm × 1200 mm × 160 mm; Construction, requirements and testing DIN 55428 Packaging materials - cardboard Part 1 requirements, testing Part 2 wet strength; Requirements, testing, DIN 55429 packaging; Cardboard boxes, cardboard or paperboard Part 2 dimensions, tolerances, testing the extent DIN 55437 Testing of board - creases Part 1 Laboratory Moderate production of Laboratory Creasing Part 2 Determination of Rillbarkeitsbereiches by visual assessment of the corrugations Part 3 Determination of technical quality DIN 55440 Packaging testing; Crush Test Part 1 test with constant feed speed DIN 55441 Packaging test - Impact test Part 2 Free Fall of plastic bottles DIN 55445 Packaging test; Examination of seams of sacks Part 1 Determination of the fracture life of stitching on paper bags Part 2 Determination of the fracture life of stitching on plastic bags Part 3 Scoring System DIN 55446 packaging, packaging materials, packaging and shipping finished packages; Sampling for t DIN 55450 packaging; Bags and bags of paper; Shape DIN 55455 packaging, tote bags and tote bags made ??of paper; Shape DIN 55457 Packaging test - Containers made of polyolefin Part 1 resistance to stress cracking; Temperature process Part 2 resistance to stress cracking; Pressure-temperature method DIN 55461 IBCs; Flexible IBCs Part 2 Dimensions DIN 55468 Packaging materials - Corrugated Board Part 1 requirements, testing Part 2 wet strength, requirements, testing DIN 55471 polystyrene foam for packaging
Part 1 requirements, testing Part 2 Calculation and design of packaging Moldings
DIN 55475 Packing aids - Tapes from power - Not reinforced or reinforced, water or heat activatable; R testing DIN 55477 Packing aids, tapes of plastic, non-reinforced and reinforced; Requirements and testing DIN 55479 Packaging - closure types of boxes of tapes and tape DIN 55480 packaging; Aluminum cans, with screw cap, round DIN 55481 polyethylene foam for packaging Part 1 requirements, tests DIN 55482 polyurethane foam for packaging Part 1 requirements, tests DIN 55483 Rubberized fibers and / or hair for packaging Part 1 requirements, testing DIN 55505 aerosol containers; Determining the cap seat height DIN 55507 aerosol containers; Working Surfaces of clinching pliers DIN 55510 Packaging - Dimensional coordination in packaging Chapter 1 Basics Part 2 Terminology Part 3 rules and dimensions DIN 55525 threads Mainly for plastic and glass containers with screw cap uniform; Buttress thread; Ma DIN 55529 Packaging - Determining the sealed seam strength of sealings made of flexible packaging DIN 55531 foils for packaging - aluminum composite films DIN 55560 Reclosable child-resistant packages; Screw caps with plastic push-turn system (axial pressu Part 1 Mechanical trick system scan WITHDRAWN without replacement
DIN 55600 Testing of pigments - Determination of the significance of color differences of surface color formula DIN 55601 Testing of pigments; Determining of opacity value of dried pigmented paints from wedge-s
DIN 55603 Testing of pigments - Determination of relative tinting strength and residual color differenc pigments in white Reductions nach the brightness method
DIN 55607 pigments and extenders - dispersing pigments in powder coatings and Their colorimetric e application DIN 55608 pigments and extenders - Determination of water absorption value
DIN 55609 pigments and extenders - Determination of water-soluble sulfates, chlorides and nitrates b chromatography DIN 55610 Testing of pigments and solvent soluble dyes; Determination of unsulfonated primary arom DIN 55625 fillers for plastics Part 4 chalk, requirements and test methods Part 5 Natural crystalline calcium carbonate, requirements and test methods Part 6 Precipitated calcium carbonate, requirements and test methods Part 7 dolomite, requirements and test methods Part 10 adhesions of natural platy, carbonate-talc and chlorite - Requirements and test methods Part 23 of phlogopite; Requirements and test methods
Part 24 magnesium hydroxide; Requirements and test methods DIN 55626 fillers and pigments for paper and board - Specifications and test methods Part 4 chalk Part 5 Natural crystalline calcium carbonate Part 6 Precipitated calcium carbonate
DIN 55633 Paints and varnishes - Corrosion protection of steel structures by powder coating systems powder coating systems and execution of the coating DIN 55634 Coating materials and coating - Corrosion protection of supporting thin-walled steel compo DIN 55651 Solvents for paints and varnishes - Abbreviation DIN 55652 Solvents for paints and varnishes - Determination of acidity in the track area
DIN 55658 Paints and varnishes - Practical determination of the content of non-volatile and volatile co coating process DIN 55659 Paints and varnishes - Determination of pH Part 1 pH Electrodes with glass membrane Part 2 pH Electrodes with ISFET technology DIN 55660 Paints and varnishes - Wettability Part 1 Definitions and General Principles Part 2 Determination of surface free energy of solid surfaces by measuring the contact angle Part 3 Determination of the surface tension of liquids with the pendant drop method Part 4 Determination of the polar and disperse portions of the surface tension of liquids from interfacia
Part 5 Determination of the polar and dispersive component of the surface tension of liquids from con measurements on a solid body with pure disperse component of the surface energy
DIN 55662 Paints and varnishes - coatings for the automotive industry - Test of resistance to pressure test) DIN 55663 Paints and varnishes - Artificial weathering Including acidic DIN 55665 Paints and varnishes - Natural weathering of coatings - Examination of the corrosion protec
DIN 55667 Paints and varnishes - Determination of electrical conductivity and the electrical resistivity by DIN EN ISO 15091 DIN 55670 Paints and varnishes - coatings on pores and cracks with high voltage
DIN 55671 Coating materials and binders for paints - foil method for the rapid determination of the co components DIN 55672 gel permeation chromatography (GPC) Part 1 of tetrahydrofuran (THF) as eluent to Part 2 of N, N-dimethylacetamide (DMAC) as the eluent Part 3 water as eluent
DIN 55673 Paints and varnishes and Their raw materials - Nahinfrarotspektrometrische Analysis - Gen principles
DIN 55682 Solvents for paints and varnishes - Determination of water-dilutable coating Solvents in ma chromatographic method
DIN 55683 Solvents for paints and varnishes - Determination of solvent in organic Solvents Containing materials - Gas chromatographic method DIN 55685 Solvents for paints and varnishes - Alcohols - Gas chromatographic determination of the de
DIN 55686 Solvents for paints and varnishes - Esters of acetic acid - Gas chromatographic determinat purity DIN 55687 Solvents for paints and varnishes - Ketones - Gas chromatographic determination of the de
DIN 55688 Solvents for paints and varnishes - ethylene glycol - Gas chromatographic determination o
DIN 55689 Solvents for paints and varnishes - Propylene glycol ethers - Gas chromatographic determi of purity DIN 55699 processing of thermal insulation composite systems DIN 55900 Coatings for radiators Part 1 Definitions, requirements and tests for primers and industrially Applied primers Part 2 Definitions, requirements and testing for topcoats and industrially produced finishing coats DIN 55901 drying agents for paints and varnishes - Determination of the metal content of multi-metal DIN 55902 Pigments - Zinc chromate pigments, requirements and test methods DIN 55903 Pigments - Strontium chromate pigments, requirements and test methods DIN 55908 Pigments - Zinc (zinc oxide) - Analytical Methods DIN 55910 Pigments - Lithopone - Requirements and testing DIN 55912 Pigments - titanium dioxide pigments Part 2 analysis method DIN 55913 pigments; Iron oxide pigments Part 1 Technical delivery conditions Part 2 Analyzes methods DIN 55916 pigments; red lead; Technical delivery conditions DIN 55923 pigments; Aluminum aluminum pigments and pigment pastes for paints; Technical delivery DIN 55935 binders for paints, varnishes, adhesives and inks; Rosin; Requirements and testing DIN 55938 binders for paints - paint soybean oil - Requirements and testing DIN 55939 Binders for paints and varnishes - Castor oil - Requirements and testing DIN 55940 Binders for paints and varnishes - ricinene oil - Requirements and testing DIN 55943 colorants - Vocabulary DIN 55944 Colouring materials - Classification nach coloristic and chemical aspects DIN 55945 coatings and varnishes - Additional terms to DIN EN ISO 4618 DIN 55967 raw materials for paints - Glycerin - Requirements and testing DIN 55977 Testing of coloring matter; Determination of the sparingly soluble in Solvents share
DIN 55978 Testing of coloring matter; Determination of relative color strength in solutions; Spectropho DIN 55979 Testing of pigments; Determining the number of pigment carbon black DIN 55980 Determination of the color cast of nearly white samples DIN 55981 Determination of relative color cast from almost white samples DIN 55982 Testing of pigments; determination of the lightening of white pigments, paste method Supplement 1 example of the implementation by the gray paste method DIN 55983 Testing of pigments; Comparison of the color of white pigments in Purton system DIN 55984 Testing of pigments; Determining of opacity value of white and light gray media Supplement 1 example of performing a procedure with a white Alkydharzlack
Supplement 2 exemplifies the implementation of the method with a plasticized polyvinyl chloride (PVC DIN 55985 Testing of pigments (Part 1) comparison of the color of colored pigments in Purton system Part 2 Comparison of the color pigments in Purton system; Black pigments
DIN 55986 Testing of pigments; Determination of relative tinting strength and residual color difference Reductions; Colorimetric method DIN 55987 Testing of pigments; Determining of opacity value of pigmented media; colorimetric metho DIN 55988 Determination of the transparency value (glazing) of pigmented and non-pigmented; Color DIN 55991 Paints and varnishes - Coatings for nuclear facilities Part 1 Requirements and test methods Part 2 identity testing of coating materials Part 3 Planning and execution of coating work DIN 55992 deterministic mining a measure of the dust of pigments and fillers Part 1 rotation method Part 2 case method DIN 55996 Paints and varnishes - Determination of stone impact resistance of coatings Part 1: Multi-impact testing, Replaced by DIN EN ISO 20567-1: 2007-04 DIN 55997 Solvents for paints and varnishes - demineralized water - Requirements and testing
DIN 55998 Solvents for paints and varnishes - Propylene glycol ethers - Supply specification, Further r testing
DIN 55999 Solvents for paints and varnishes - ethylene glycol ethers - Supply specification, Further re testing DIN 56905 Event Production Equipment, Stage Lighting - Bipolar stage plugs 63 A, 250 V, 50/60 Hz DIN 56912 and show laser show laser systems - Safety requirements and testing DIN 56920 theater technology Part 1 terms for theater and stage species Part 2 terms for Buildings Part 3 terms for stage technology facilities Part 4 terms for lighting equipments Part 5 terms for electrical installations DIN 56921 Theatre engineering, stage machinery - Flying systems Part 1 manual counterweight flying with a load capacity up to 500 kg DIN 56922 Theatre engineering, stage surgery; Theatre drill (drill stage) DIN 56923 Theatre engineering, stage surgery; Beaten plug hinges DIN 56924 booths for simultaneous transmission Part 1 stationary Part 2 portable
DIN 56926 Theatre engineering, stage operation - Quick link with lock nut - Dimensions, requirements 2009 Replaced by DIN 56927
DIN 56927 Theatre engineering, stage operation - Safety rope to secure objects up to 60 kg - Dimensi requirements and testing DIN 56930 Stage Technology - Stage lighting control systems
Part 1 Definitions, requirements Part 2 control signal DIN 56950 Event Production Equipment - Machinery - Safety requirements and testing DIN 56955 Event technology - loads in stages and secondary areas - traffic loads DIN 57510 VDE Specification for rechargeable batteries and battery systems DIN 57532 transformers and reactors Part 21 transformers and inductors occasion occasion [VDE Specification] DIN 58122 Quantities, units and symbols; Overview for teaching Supplement 1 Notes for Teaching DIN 58124 Satchel - Requirements and testing DIN 58220 visual acuity Part 3 examination of reports
Part 5 General eye test (used for occupational medical examinations nach the trade association princi G 37) Part 6 traffic-related eye test Part 7 Mesopic contrast sensitivity with and without glare, for road-traffic related testing (draft) DIN 58230 Medical instruments - Catlings DIN 58231 Medical instruments - Hemostatic Forceps nach Halstead DIN 58232 Medical instruments - Hemostatic Forceps cooker and cooker Ochsner DIN 58233 Medical instruments - Hemostatic Forceps by Overholt Geißendörfer DIN 58234 Medical instruments - Hemostatic Forceps Rochester-Pean DIN 58235 Medical instruments - Hegar Needle Holder Mayo Part 1 Without carbide inserts Part 2 with carbide inserts DIN 58236 Medical instruments - Mathieu Needle Holder Part 1 Without carbide inserts Part 2 with carbide inserts DIN 58237 Medical instruments - splinter tweezers Feilchenfeld DIN 58238 Medical Instruments Part 1 Anatomical tweezers, straight Part 2 Curved DIN 58239 Medical Instruments - Surgical Forceps Part 1 Straight Part 2 Curved DIN 58240 Medical instruments - Retractor Israel DIN 58241 Medical instruments - Hemostatic Forceps Crile DIN 58242 Medical instruments - artery forceps Dandy DIN 58243 Medical instruments - Intestinal Clamps cooker DIN 58244 Medical instruments - Intestinal Clamps Mayo-Robson DIN 58245 Medical instruments - Backhaus Towel Clamps DIN 58246 Medical instruments - Peritoneumklemme Mikulicz
DIN 58247 Medical instruments - Retractor Roux DIN 58248 Medical instruments - Retractor by Jansen DIN 58249 Medical instruments - Retractor accor ding Weitlaner DIN 58250 Medical instruments - Operations scalpels DIN 58251 Medical instruments - scalpels Bergmann DIN 58252 Medical Instruments Part 1 Just surgical scissors without carbide inserts DIN 58253 Medical Instruments Part 1 Bent-surgical scissors without carbide inserts DIN 58254 Medical instruments - Inzisionsscheren DIN 58255 Medical instruments - tweezers to Great Part 1 Straight Part 2 Broken Bow DIN 58256 Medical instruments - Needle holder Tönnis DIN 58257 Medical instruments - Needle holder Crile DIN 58259 Medical instruments - Needle holder Masson DIN 58260 Medical instruments - Ligature Needles by Deschamps DIN 58262 Medical instruments - Mouth Gag Jennings DIN 58263 Medical instruments - for Spread Heister DIN 58264 Medical instruments - Rib Spreaders Finochietto DIN 58265 Medical instruments - Needle holder Finochietto DIN 58266 Medical instruments - Needle holder Crile-Wood Part 1 Without carbide inserts Part 2 with carbide inserts DIN 58267 Medical instruments - Mathieu Needle Holder with internal lock DIN 58270 Medical instruments - Knee Curved Tweezers DIN 58271 Medical instruments - bayonet-shaped forceps DIN 58272 Medical instruments - Fine Tweezers DIN 58273 Medical instruments - Fixation DIN 58274 Medical instruments - Iris Forceps DIN 58275 Medical instruments - Chalazionpinzetten DIN 58276 Medical instruments - Adson Forceps DIN 58277 Medical instruments - wound clamp forceps watch box DIN 58278 Medical instruments - Cilienpinzette DIN 58279 Medical instruments - first aid kit scissors DIN 58280 Medical instruments - Iris scissors without carbide inserts DIN 58281 Medical Instruments Part 1 Strabismusschere carbide inserts without DIN 58282 Medical instruments - Tenotomieschere Stevens DIN 58285 Medical instruments - Retractor Volkmann DIN 58286 Medical instruments - Retractor type Kocher
DIN 58287 Medical instruments - Retractor Körte DIN 58288 Medical instruments - Retractors Langenbeck DIN 58289 Medical instruments - abdominal wall and liver Mikulicz hook with curved blade DIN 58290 Medical instruments - Retractor Bergmann DIN 58291 Medical instruments - Retractor Simon and nach Martin DIN 58292 Medical instruments - Trachealhaken DIN 58293 Medical instruments - Trachealhaken by Bose DIN 58294 Medical instruments - Lidhalter after Desmarres DIN 58295 Medical instruments - Bone Hook Volkmann DIN 58296 Medical instruments - Raspatories by Semb DIN 58297 Medical instruments - Rippenraspatorien by Doyen DIN 58298 Medical instruments - Materials, finish and testing DIN 58299 grooves for surgical instruments, profile angle, partitions DIN 58300 Final kinds of surgical instruments DIN 58312 Medical instruments - Rippenkontraktor DIN 58313 Medical instruments - Cotton Carriers, just DIN 58314 Medical instruments - laryngeal cotton swab after fine DIN 58315 Medical instruments - Retractor Cushing DIN 58316 Medical instruments - Abdominal Patel, flexible DIN 58317 Medical instruments - Elevator by Henke DIN 58318 Medical instruments - Elevators Langenbeck DIN 58319 Medical instruments - Elevator Williger DIN 58320 orthopedics, orthopedic and technical aids and remedies Part 1: Overview, classification Part 2 names and items of lower limb prostheses DIN 58324 orthopedics, floor buffer DIN 58345 Refrigerators for drugs - Definitions, requirements, testing DIN 58355 membrane filter Part 1 examination of the specific flow rate of liquids for flat filter Part 2 examination in bladder pressure Part 3 bacteria retention capacity for flat filters - Requirements and testing Part 4 test particle emission Part 6 Test for extractables DIN 58356 membrane filter elements Part 1 Requirements and testing of the bacteria retention capacity Part 2 pressure hold test Part 3 examination of the specific flow rate of liquids Part 7 Test of sterilization in the steam flowing Part 8 Examination of sterilization with steam Part 9 Test for endotoxins Part 10 Determination of non-volatile extractables - limiting concentration in the filtrate
Part 11 Determination of non-volatile extractables by dip method Part 12 integrity testing of hydrophobic membrane filter elements with water
DIN 58369 transfusion, infusion - Einmalaufhängevorrichtung for transfusion bottles and infusion bottl testing, DIN 58371 Blood Bank Refrigerators - Definitions, requirements, testing DIN 58375 Plasma storage - Definitions, requirements, testing DIN 58395-temperature applications of lubricants for precision engineering and optical equipment DIN 58396 Lubricating greases for precision engineering and optical equipment Part 2 Minimum Requirements DIN 58397 optical engineering - Testing of lubricating greases for precision engineering and optical eq Part 1 Evaporation loss Part 2 spreading behavior DIN 58400 for involute spur gears reference profile in the precision engineering DIN 58405 helical gear precision engineering Part 1 Scope, definitions, determinants, classification Part 2 Getriebepassungsauswahl, tolerances, Deviations Part 3 details in drawings, calculation examples Part 4 tables DIN 58411 hobs for spur gears precision engineering with modules 0.1 to 1 mm DIN 58412 reference profiles for gear cutting precision engineering; involute to DIN 58400 and DIN 86 DIN 58413 tolerances for precision engineering hobs DIN 58420 Master gears for testing spur gears precision engineering, hubs and teeth DIN 58425 circular arc gears for Precision Engineering Part 1: Overview, symbols, terms, Part 2 tooth profile Part 3 Calculation and design of wheel and pinion Part 4 Permitted Deviations and tolerances for wheel and pinion Part 5 profiles for gear milling cutters Part 6 indications on drawings Part 7 tables, charts, DIN 58450 lens screws with slot; Scale screws DIN 58460 stud for precision engineering DIN 58461 shoulder bolt with collar for Precision Engineering DIN 58462 stud with groove for Precision Engineering DIN 58463 shoulder bolt with collar and groove for fine mechanics DIN 58464 stud with head for precision engineering DIN 58466 Dimensional layout for parts for precision engineering DIN 58467 connectors with straight pins for Precision Engineering DIN 58469 shoulder bolts with thread for Precision Engineering DIN 58470 stud with hexagon and a thread for Precision Engineering DIN 58471 stud with hexagon, thread and groove for fine mechanics
DIN 58472 with shoulder bolt head and thread for Precision Engineering DIN 58500 names of witnesses tear DIN 58502 drawing sets; Requirements, testing, DIN 58505 purpose compass for precision drawing instruments (P) DIN 58506 Dividers for precision drawing instruments (P) DIN 58507-use bow compass for precision drawing instruments (P) DIN 58508 part circle for precision drawing instruments (P) DIN 58509 bow compass for precision drawing instruments (P) DIN 58510 Graphite Mine inserts for precision drawing instruments (P) DIN 58511 tensile spring inserts for precision drawing instruments (P) DIN 58512 lace inserts for precision drawing instruments (P) DIN 58513 Extension rod for precision drawing instruments (P) DIN 58515 needles for drawing instruments DIN 58516 case needles for drawing instruments DIN 58518 tensile springs for precision drawing instruments (P) DIN 58519 drawing pens, swedish style, for precision drawing instruments (P) DIN 58520 Screws for drawing instruments Part 1 T-bolts Part 2 Kegelsenkschrauben DIN 58521 knurled nuts for drawing instruments DIN 58522 graphite mines for drawing instruments DIN 58530 screws for drawing instruments DIN 58531 clamping screws for drawing instruments DIN 58532 drawing instruments - Extension rod for large use part-circle DIN 58537 drawing sets; Proportional dividers DIN 58538 drawing sets, Giant bow compass and great use part circle DIN 58540 standard for use compasses drawing instruments (S) DIN 58541 Divider for standard drawing instruments (S) DIN 58542 Reversible pair of dividers for standard drawing instruments (S) DIN 58543 part circle for school drawing instruments (S) DIN 58544 standard bow compass for drawing instruments (S) DIN 58545 inserts for graphite mines or needles for standard drawing instruments (S) DIN 58546 tensile spring inserts for standard drawing instruments (S) DIN 58548 standard extension rod for drawing instruments (S) DIN 58551 Means drives for drawing instruments DIN 58552 threaded bushings for drawing instruments DIN 58553 needle holder for drawing instruments DIN 58556 Quick Set and Bit Quick Set DIN 58600 Respiratory protective devices - End the connection between regulator for compressed air in pressure-design and facepiece for German firefighters
DIN 58610 Respiratory protective devices - Full face masks connected with head protection for use as for firefighters
DIN 58620 Respiratory protective devices - gas filters and combined filters for protection against carb Requirements, testing, marking
DIN 58621 Respiratory protective devices - reactor filter for protection against radioactive methyl iodi particles - Requirements, testing, marking big DIN 58629 Optics and optical instruments - Vocabulary for microscopy Part 1 light microscopy
DIN 58639 Respiratory protective devices for self-rescue - Breathing apparatus with oxygen with hood Requirements, testing, marking DIN 58647 Respiratory protective devices for self-rescue Part 7 Filter Escape Devices; Requirements, testing, marking DIN 58651 Respiratory protective devices - breathing apparatus Part 2 momentary push oxygen protective devices for light work; Requirements, testing, marking DIN 58652 Respiratory protective devices - breathing apparatus Part 1 Short duration-chemical (KO2) protection devices for light work; Requirements, testing, marking Part 2 Chemical oxygen (KO2) protection devices for work and rescue; Requirements, testing, marking Part 3 Short duration-chemical (NaClO 3) protection devices for light work; Requirements, testing, mar Part 4 Chemical oxygen (NaClO 3) protection devices for work and rescue; Requirements, testing, mar DIN 58653 Meteorological equipment - minimum thermometer DIN 58654 Meteorological equipment - Maximum thermometer DIN 58655 Meteorological equipment - Soil thermometer 20-310 mm DIN 58660 Meteorological equipment - Thermometer 370 for psychrometer DIN 58661 Meteorological equipment - Thermometer 280 for psychrometer DIN 58664 Meteorological equipment - ground-deep thermometer, 500 mm and 1000 mm DIN 58681 jewelry label Part 1 label for jewelry series DIN 58682 gold plating for jewelry, terms, labeling DIN ISO 58700 fits; Tolerance range for precision engineering Part 1 tolerance zones, Nennabmaße Part 2 Recommended fits DIN 58722 optical engineering - terms of optical engineering Part 1 working procedures Part 2 Equipment DIN 58623 optical engineering - Diamond Facettierwerkzeuge DIN 58624 optical engineering - spherometer - Meßringe DIN 58940 Medical microbiology - Susceptibility testing of microbial pathogens to antimicrobial agents Part 1 Definitions Part 2 drug carriers for the agar diffusion test; Text in German and English Part 3 agar diffusion test; Text in German and English Part 4 Evaluation classes of the minimum inhibitory concentration
Part 6 Determination of the minimum inhibitory concentration (MIC) by the agar dilution method; Text English
Part 7 Determination of minimum bactericidal concentration (MBC) with the Mikrobouillondilutionsmet German and English
Part 9 regression analysis to correlate inhibition zone Diameters (HHD) and minimum inhibitory conce in German and English Part 10 criteria for the evaluation of the in vitro efficacy of novel chemotherapeutic agents Coding part 20 of Antibacterial Agents Part 31 Supplementary Procedures for susceptibility testing; Text in German and English Part 82 microdilution; Specific requirements for testing of fastidious bacteria Part 83 microdilution; Specific requirements for the testing of strictly anaerobic bacteria Part 84 microdilution; Specific requirements for testing of fungi to antifungal agents DIN 58950 Sterilization - Steam sterilizers for pharmaceutical products Part 1 terms; Text in German and English Part 2 equipment requirements; text in German and English Part 3 tests; Text in German and English Part 6-operation; Text in German and English Part 7 requirements for equipment and construction requirements; Text in German and English DIN 58953 Sterilization - Sterile Part 1 Definitions Part 6 Microbial barrier testing of packaging materials for sterilized medical devices
Part 7 Use of sterilization paper, nonwoven fabrics, woven textile materials, paper bags and sealable p Part 8 Logistics of sterile medical devices Part 9 Use of sterilization DIN 58959 Quality management in medical microbiology Part 1 Requirements for the QM-system Part 2 Requirements for sample collection, transport and acceptance of specimens Part 3 Requirements for the sample order and report of findings Part 4 requirements for light microscopy Part 6 Requirements for control strains Part 7 General requirements for the use of control strains Part 8 requirements for the use of control strains for testing swabs, transportation, dipping and blood Part 9 requirements for the use of control strains for testing culture media Part 10 requirements for the use of control strains for testing reagents, dyes and biological materials Part 11 requirements for the use of control material for testing ready-made tests and test kits Part 12 requirements for the use of control material for testing immunological reagent kits Part 14 requirements for the use of control strains for susceptibility testing of aerobic bacteria Part 15 requirements for the use of control strains for susceptibility testing of anaerobic pathogens Part 16 requirements for the use of control strains for susceptibility testing of special bacteria Part 17 requirements for the use of control strains for the examination of mycobacteria; Text in Germa Part 18 requirements for the use of control strains for the examination of mycoplasma Part 19 requirements for the use of control strains in the study of fungi Part 20 requirements for the use of control materials in the study of protozoa and highly organized mi
DIN 58970 Laboratory centrifuges Part 1 Definitions, testing, marking Part 2 centrifuge tubes for RZB to 4000 DIN 59145 Spring steel, hot-rolled, with semicircular short sides; January, 2004 Replaced by DIN EN 10
DIN 59146 Spring steel, hot-rolled, with a rectangular cross-section and rounded edges for leaf spring Replaced by DIN EN 10092-1
DIN 59200 Flat products made of steel - Hot-rolled wide flats - Dimensions, mass, tolerances, toleranc limit Deviations of mass
DIN 59220 steel flat products - Hot-rolled with patterns - weights, dimensions, tolerances on dimensio shape and limit Deviations of mass
DIN 59410 hollow sections of structural steel, Hot finished square and rectangular steel tubes, dimens Deviations in December 1997 Replaced by DIN EN 10210-2
DIN 59411 hollow sections for steel construction; Cold FORMED welded square and rectangular steel t weights, tolerances, December 1997 Replaced by DIN EN 10219-2 DIN DIN DIN DIN DIN DIN
59413 Cold rolled steel sections, Permissible dimensional, shape and weight Deviations, Decembe EN 10162 59755 Pipes made ??of nickel and wrought nickel alloys, cold finished, Dimensions, tolerances 59760 round bars of wrought nickel and nickel alloys, hot rolled - Dimensions, Dimensional toleran 59765 round bars of wrought nickel and nickel alloys drawn - Dimensions, Dimensional tolerances 60000-69999 [ Edit ]
DIN 60000 Textiles - Basic concepts DIN 60001 Textile fibers DIN 60455 Identification of equipment terminals DIN 60905 Tex system Chapter 1 Basics Part 3 rounding calculated is subtleties DIN 60917 Knitted machines; Comparison of subtleties and needle pitches (invalid) DIN 61010 Textiles - Upholstery fabrics for the home DIN 61101 weaves Part 1: General concepts, basic weaves DIN 61106 system for forming pattern repeats DIN 61110 loom harness indents, Concepts and Classification DIN 61200 felts; Hardness DIN 61211 prepared in Nähwirkanlagen fabric - Technological Classification, terms DIN 61400 sewing machines - Stitch types - Classification and terminology (ISO 4915: 1991, modified) DIN 61506 One-piece overalls for men; Combinations and boiler suits DIN 61512 Work Overalls for Men DIN 61513 Work Overalls for Women DIN 61535 Work Coats for men; Short and long form
Part 1 Minimum Requirements and tests (the proposal for a European standard), March, 2004. Replace DIN 61551 Geosynthetics - Determination of burst strength
DIN 61577 stitch widths for sewing on two- and four-hole buttons DIN 61603 use sizes of sheets Part 1 bedding for adults DIN 61631 surgical dressings; Gauze DIN 61632 surgical dressings; Ideal binding DIN 61633 surgical dressings, bandages stockinette DIN 61634 surgical dressings; Flexible Bandage DIN 61650 swabs DIN 61651 Machine-cleaning cloths DIN 61704 operations in the textile finishing industry for fabric, knitted or crocheted DIN 61712 winders for textile fabrics DIN 61750 bases of the shipping Packaging for textiles DIN 61751 bases of the sales units of textiles Part 1 Crocheted and knitted underwear sleepwear Including Part 2 Knitted men's and children's socks, knitted tights DIN 61752 Lege dimensions for sales units of textiles Part 1 household linen and dowry Part 2 handkerchiefs Part 3 ready-made curtains Part 4 Workwear Part 5 smocks and aprons Part 8 wipes Part 9 tapestries DIN 61850 glass and textile processing aids; Terms DIN 61853 Textile glass, textile glass mats for plastics reinforcement Part 1 Technical delivery conditions Part 2 classification and application DIN 61854 Textile glass; Textile glass fabric for reinforcing plastics; filament fabric and woven roving Part 1 Technical delivery conditions Part 2 types DIN 62055 Knitted or crocheted fabrics; Polstoffe; Terms DIN 62130 circular knitting machines; Terms DIN 62136 Textile machinery and accessories - Needle and sinker lubricating oils for knitting machines Part 1 Minimum requirements of mineral oil based Part 2 Minimum requirements synthetic oil based DIN 62150 bearded needles for circular knitting machines RL, system around DIN 62151 bearded needles for circular knitting machines RL, shaft flat and stretched DIN 62154 boards for flat knitting machines RL; Terms DIN 62155 boards for warp knitting machines RL; Terms DIN 62500 and warp preparation equipment for warp preparation - Vocabulary DIN 63201 Graphical symbols for textile machinery
DIN 63202 Textile machinery and accessories - Safety Signs - Warning Signs DIN 64083 flyers for the cotton spinning; Concepts, principles of construction DIN 65000 Aerospace - subject groups directory of aerospace standards Part 1 basic standards, materials, semi-finished products, standard parts Part 2 Electrical Engineering Part 7 air cargo and ground equipment DIN 65002 Aerospace; Electrical, circular; Technical delivery conditions DIN 65004 Aerospace; Machine screws with cruciform recess, with long thread
DIN 65013 Aerospace; Screws from high-strength steel and corrosion resistant Ni and Co-based mater tensile strength of 1 800 MPa - Technical delivery conditions
DIN 65016 Aerospace; Self-locking nuts with Reduced backup moment with a maximum operating tem or equal to 425 ° C - Technical Specification DIN 65021 Aerospace; Sheets, plates and strips of steel, nickel and cobalt alloys; Technical delivery co
DIN 65030 Aerospace; Soldering compression fittings with cutting ring - Technical delivery conditions;
DIN 65033 Aerospace; Forgings of aluminum and magnesium alloys; Technical specification; Not for ne forgings of aluminum alloys DIN 65034 Aerospace; Casting from steel, nickel and cobalt alloys; Technical specification; Not for new
DIN 65035 Aerospace; Raw materials, forgings and rings of steel, nickel and cobalt alloys; Technical sp new designs of tested material, forgings and steel rings DIN 65038 Part 1 Aerospace; Rods made ??of steel, nickel and cobalt alloys; Technical delivery conditions Part 2 Aerospace; rods of steel, nickel and cobalt alloys for aviation equipment; Technical delivery con DIN 65039 Aerospace; Plates, sheets and strip of titanium and titanium alloys; Technical delivery cond
DIN 65040 Aerospace; rods, rings, forging stock and forgings of titanium and titanium alloys; Technica DIN 65046 Aerospace; Methods of test for surface protective coatings; coating materials Part 1 Introduction and Abbreviations Part 2 samples, sample preparation, drying Part 3 trials as delivered Part 4 tests of coatings Part 5 Coating resistance tests Part 6 Chemical and galvanic coatings - Not for new designs DIN 65080 Aerospace; Pickling of aluminum and aluminum alloys alkaline; Identification number 0110 DIN 65083 Aerospace; Heat treatment of castings of titanium and titanium alloys DIN 65084 Aerospace; Heat treatment of titanium and titanium-wrought DIN 65090 Aerospace; Textile glass, pre-impregnated filament of E-glass (prepreg), technical specifica
DIN 65092 Aerospace; Testing of Aircraft equipment under environmental conditions; Checking the ins and dielectric strength of electrical appliances; Identical with ISO 2678: 1985 DIN 65099 Aerospace; Classification of special workshop Part 1 Overview Part 2 process group A; Urformen
Part 3 process group B; Reshape Part 4 process group C; Separate Part 5 process group D; Put Part 6 process group E; Coating Part 7 process group F; material propertyChange Part 8 process group G; Check Part 9 process group H; Cause of material, design work environment, transport DIN 65142 Aerospace; prepreg plies (prepreg); The bond strength DIN 65144 Aerospace; Thermally sprayed structures; Technical delivery conditions DIN 65145 Part 1 Aerospace; supply device for flash warning lights Part 2 Aerospace; supply device for flash warning lights; Technical delivery conditions DIN 65147 Aerospace; carbon fibers; Fabric of carbon filament Part 1 Dimensions, masses Part 2 Technical delivery conditions DIN 65148 Aerospace; Testing of fiber-reinforced plastics; interlaminar shear strength Determine the i DIN 65149 Aerospace; Steel screws for non-structural elements, M 3 and M 4, Technical specifications DIN 65202 Aerospace; O-rings made ??from elastomers - Dimensions
DIN 65220 Aerospace; Anniet nut bars with self-locking nuts withMJ thread- Set parent division or OPT aluminum; Classification: 1100 MPa / 120 ° C
DIN 65300 Aerospace; universal joints, needle bearings, with long-term lubrication for rotary shafts; Te conditions DIN 65304 Aerospace; Seals - Technical delivery conditions DIN 65306 Aerospace; inserts for composite materials, with clearance hole stainless steel
DIN 65307 Aerospace; inserts for composite materials, with MJ thread, closed, light weight, screw-lock resistant steel; Text in German and English
DIN 65308 Aerospace; inserts for composite materials, with MJ thread, open type, screw-locking, corro Text in German and English
DIN 65309 Aerospace; inserts for composite materials, with MJ thread, closed type, screw-locking, corr Text in German and English
DIN 65313 Aerospace; Pan head screws with ribbed cruciform recess and MJ thread, threaded to head resisting steel; Tensile strength 1100 MPa, for Temperatures up to 425 ° C
DIN 65314 Aerospace; countersunk bolts fitting with ribbed cruciform recess with MJ thread, short thre tensile strength 1100 MPa, for Temperatures up to 235 ° C
DIN 65316 Aerospace; countersunk bolts fitting with ribbed cruciform recess and MJ thread, short thre resisting steel; Tensile strength 1100 MPa, for Temperatures up to 425 ° C
DIN 65317 Aerospace; Countersunk screws with ribbed cruciform recess and MJ thread, short thread, s strength 1100 MPa, for Temperatures up to 235 ° C
DIN 65318 Aerospace; Pan head screws with ribbed cruciform recess and MJ thread, short thread, stee 1100 MPa, for Temperatures up to 235 ° C
DIN 65319 Aerospace; flat-head fitting bolts with ribbed cruciform recess and MJ thread, short thread, steel; Tensile strength 1100 MPa, for Temperatures up to 425 ° C
DIN 65320 Aerospace; flat-head fitting bolts with ribbed cruciform recess and MJ thread, short thread, strength 1100 MPa, for Temperatures up to 235 ° C DIN 65321 Aerospace; panels, windows and Moldings made ??of acrylic glass; Technical delivery cond
DIN 65324 Aerospace; flat-head fitting bolts with ribbed cruciform recess and MJ thread, short thread, Tensile strength 1100 MPa, for Temperatures up to 315 ° C
DIN 65330 Aerospace; hexagon head bolts with MJ thread, short thread of steel; Tensile strength 1100 Temperatures up to 235 ° C
DIN 65338 Aerospace; Hexagon fit bolts with MJ thread, short-contrasting thread, in titanium alloy; Ten MPa, for Temperatures up to 315 ° C
DIN 65339 Aerospace; Hexagon fit bolts with MJ thread short, thread, corrosion resisting steel in - tens MPa, for Temperatures up to 425 ° C
DIN 65342 Aerospace; Anchor nuts with MJ thread, with counterbore, self-locking, two lug, Reduced se class: 1100 MPa / 315 ° C / 425 ° C
DIN 65375 Aerospace; Fibre reinforced plastics; Testing of unidirectional laminates; Compression test t fiber direction DIN 66000 Information processing; Mathematical signs and symbols of switching algebra DIN 66001 symbols for data flow diagrams and flow charts DIN 66002 Handwritten representation of the number 0 and the capital letter O DIN 66003 Information Processing, 7-bit code DIN 66004 coding on data carriers; Representation of the 7-bit code and the 8-bit code on punched ca DIN 66005 Space-saving representation of Purely numerical data on magnetic tape with 9 tracks 12-D DIN 66006 representation of ALGOL / ALCOR programs on paper tape and punched cards DIN 66007 font CMC 7 for machine magnetic character recognition, December 1999 Replaced by DIN DIN 66008 A font for automatic optical character recognition DIN 66009 B font for the automated optical character recognition DIN 66020 interfaces in telephone networks DIN 66021 data transmission DIN 66025 Program structure for NC machines DIN 66027 FORTRAN DIN 66030 Information Technology - Presentation of unit names in systems with limited character stoc DIN 66071 steel rake DIN 66072 porcelain dinnerware for the commercial sector; Mass DIN 66074 Shoe sizes Chapter 1 Basics of a multivariable system (Mondo Point system) Part 2 step length Part 3 Weitenstufung for women's and men's footwear DIN 66075 devices for catering DIN 66080 Classification of burning behavior of textile products; Principle DIN 66083 parameters for the burning behavior of textile products - Textile fabrics for workwear DIN 66084 Classification of burning behavior of upholstery composites DIN 66090 Textile floor coverings Part 1 Requirements for construction, fire behavior
DIN 66111 sedimentation analysis, basics DIN 66115 particle size analysis; Sedimentation in the gravitational field; Pipette method DIN 66118 visual analysis, basics
DIN 66132 Determination of the specific surface area of solids by nitrogen; one-point difference metho Dümbgen DIN 66133 Determination of pore volume distribution and specific surface area of ??solids by mercury
DIN 66134 Determination of pore size distribution and specific surface area of ??mesoporous solids by A process nach Barrett, Joyner and Halenda (BJH) DIN 66135 Particle Measurement - micropore analysis by gas adsorption Chapter 1 Principles and methods of measurement Part 2 determination of the micropore volume and the specific surface area by Isothermenvergleich Part 3 Determination of the micropore volume by Dubinin and Radushkevich Part 4 Determination of the pore distribution nach Horvath-Kawazoe and Saito-Foley DIN 66137 Determination of density of solids Chapter 1 Basics Part 2 Gaspyknometrie Part 3 gas buoyancy method DIN 66138 isothermal measurement of sorption of vapors of solids DIN 66139 pore size analysis - Preparation of pore size distributions DIN 66142 presentation and labeling of separations disperse goods Part 3 selection and determination of characteristic values ??When operating divisions DIN 66143 representation of grain (particle) size distributions - Potentenznetz DIN 66144 representation of grain (particle) size distributions - Logarithmic Normal Distribution Netwo DIN 66145 size distributions representation of grain (particle) - RRSB network DIN 66160 measuring disperse systems, concepts DIN 66161 particle size analysis , Symbols, units DIN 66165 particle size analysis, sieve analysis Chapter 1 Basics Part 2 Implementation DIN 66201 Process Control Systems Part 1 terms; July 1998 Replaced by DIN V 19233 DIN 66215 CLDATA DIN 66230 Information processing; Withdrawn program documentation, June, 2004 without replaceme DIN 66231 Information processing; Withdrawn program development documentation, June, 2004 with DIN 66232 Information processing; Withdrawn data documentation, June, 2004 without replacement DIN 66234 workstations Part 1 Geometric design of the characters, february Replaced in 1998 by DIN EN 29241-3 Part 2 visibility of characters on screens in February 1998 Replaced by DIN EN 29241-3 Part 3 WITHDRAWN grouping and formatting of data, without in February 1998 replacement
Part 3, Supplement 1, grouping and formatting of data; Withdrawn without replacement instructions a February 1998 Part 5 encoding information, february Replaced in 1998 by DIN EN 29241-3
Part WITHDRAWN 5 Supplement 1 encoding information, use of graphics February 1998 excluding rep Withdrawn Part 5 Supplement 2 encoding information, color Combinations, february 1998 excluding re Part 6 of the workplace, April 2002 Replaced by DIN EN 29241-3 Part WITHDRAWN 6, Supplement 1 design of the workplace, examples, April 2002 excluding replacem
The ergonomically designed operator Part 7 compartment - lighting and arrangement, April 2002 Repl 29241-3 Part 8 principles of ergonomic design of dialogue, May 1996 Replaced by DIN EN ISO 9241 -10 Part 9 February measuring method, Replaced in 1998 by DIN EN 29241-3 Part WITHDRAWN 10 minimum information for display devices, Aug 2001 Own DIN 66241 Information processing; decision table specification Means DIN 66253 Information technology - Programming language PEARL Part 2 PEARL 90 Part 3 multi-computer PEARL DIN 66255 PL / I DIN 66256 PASCAL DIN 66257 terms for NC machines DIN 66258 interfaces for data transmission DIN 66261 Nassi-Shneiderman diagram , A design method for structured programming DIN 66264 multiprocessor control system (MPST)
DIN 66265 interfaces of a core for transaction-oriented application system (TAS KDCS-core); the acron "Compatible Data Communication Interface" DIN 66271 software defects and Their evaluation by suppliers and customers DIN 66272 Rate of software products - Quality characteristics and guidelines for Their use DIN 66273 Information processing; Measuring and Evaluating the performance of computer systems Part 1 measurement and assessment techniques Part 1, Supplement 1, measurement and assessment techniques; Introduction to the method Part 2 standard load type A Part 3 standard load type B Part 4 standard load type C DIN 66285 requirements for standard software (eg functions on this page, efficiency, maintainability) DIN 66291 chip cards with digital signature application / function nach Act / SigV Part 1 application interface Part 2 personalization services Part 3 personalization commands Part 4 Basic security services DIN 66303 Information technology, 8-bit code DIN 66304 computer assisted construction DIN 66349 interface for parallel Meßdatenübermittlung; BCD interface DIN 66399 and office systems - destruction of data carriers Chapter 1 Basics and Terminology Part 2 Requirements for machines to destroy disks DIN 67500 illumination of lock systems, requirements, calculation and measurement
DIN 67510 Photoluminescent pigments and products Part 1 measuring and marking the manufacturer Part 2 Measurement of photoluminescent products at the site of application Part 3 Ground-level photoluminescent safety guidance system Part 4 Products for photoluminescent safety guidance system; and Markings DIN 67519 Actinismin the optical range; Concept measurement application DIN 67520 Retroreflective materials for traffic safety and photometric requirements for reflective mate DIN 67523 Lighting of pedestrian crossings (sign 293 StVO) with additional lighting Part 1 General quality characteristics and guide values Part 2 Calculation and measurement DIN 67524 lighting of road tunnels and underpasses Part 1 General quality characteristics and guide values Part 2 Calculation and measurement DIN 67526 sports lighting Part 3 Guidelines for daylighting DIN 67527 Photometric properties of traffic signal lights Part 1 Stationary signal lights on the road DIN 67530 Reflectometer as a Means for gloss assessment of plane paint and plastic Surfaces
DIN 68100 Tolerance system for wood working and wood processing - Concepts, series of tolerances, s swelling DIN 68101 Deviations fundamentals and tolerance zones for wood processing DIN 68119 wood shingles DIN 68120 wood profiles; Basic shapes DIN 68121 Timber profiles for windows and doors Part 1 dimensions, quality requirements Part 2 General principles DIN 68125 Part 1 of plinths European (except Nordic) wood Part 2 plinths of northern softwood DIN 68126 lining with shadow groove Part 1 Dimensions DIN 68127 acoustic boards DIN 68128 balcony boards DIN 68140 finger joints of wood Part 1 WITHDRAWN finger jointed softwood for load-bearing components, replacement DIN 68141 wood adhesives - Testing of properties of adhesives for load-bearing timber structures DIN 68150 wooden dowel Part 1 dimensions and technical delivery DIN 68163 fastening elements for the manufacture of wooden pallets; Nails DIN 68201 average loss in wood; Definitions and calculation method DIN 68255 Schnittholzpaketierung
DIN 68330 veneers; Terms DIN 68340 handles of wood for impact tools; Technical delivery conditions DIN 68345 screw connection for handles and brooms; threaded cap and threaded insert DIN 68346 Brooms, brushes; Identification of Besteckungsmaterialien DIN 68361 orchard ladders made of wood - Dimensions, requirements and testing DIN 68362 Wood for ladders and steps - Quality requirements DIN 68363 Fruit Tree aluminum ladders - Dimensions, requirements and testing DIN 68364 characteristics of wood species - Density, modulus of elasticity and strength DIN 68365 timber for carpentry work - Appearance grading - Softwood DIN 68368 hardwood lumber for stair - Quality Conditions DIN 68702 Holzpflaster DIN 68705 Plywood Part 2 rod and rod plywood for general purposes DIN 68706 interior doors made of wood and wood-based materials Part 1, door skins, Definitions, dimensions, requirements Part 2 door frames; Definitions, dimensions, installation DIN 68762 Chipboardfor special purposes in building; Definitions, requirements, testing DIN 68764 particleboard; Strangpreßplatten for the construction industry Part 1 WITHDRAWN concepts, properties, testing, monitoring, July 2007 without replacement Withdrawn Part 2 planked Strangpreßplatten for the panel construction, July 2007 without replacemen DIN 68800 wood protection Part 1 General Part 2 Preventive constructional measures in buildings Part 3: Preventive protection of wood with wood preservatives Part 4 control and restoration of wood destroying fungi and insects Part 5 preventive chemical protection of wood materials, Replaced by DIN 68800-3 DIN 68858 Hardware for furniture, drawer runners, drawers and pull-outs, requirements and testing DIN 68861 furniture Surfaces Part 1: Behaviour at chemical strain Part 2: behavior at abrasion Part 4: Response to scratches Part 6: Behaviour at cigarette burns Part 7: Behaviour in dry heat Part 8: Reaction with moist heat DIN 68871 Furniture designations DIN 68874 Furniture Shelves and shelf bearers Part 1 Requirements and testing in Furniture Part 2 Requirements and test the bottom support DIN 68876 housework swivel, height adjustable; Safety requirements and testing DIN 68877 Swivel chair; Safety requirements and testing DIN 68878 chairs for domestic use - Characteristics - Requirements and test methods
DIN 68930 Kitchen furniture - usability - Requirements and testing DIN 68935 coordination dimensions for bathroom furniture, appliances and sanitary objects DIN 69001 machine tools; Multiple Spindle Heads DIN 69002 Machine tools - short spindles Part 1 General description basics Part 2 dimensions and parts list, description Part 3 items
DIN 69010 Transfer Center - machine interface frame - multi-spindle heads and other assemblies, size DIN 69051 machine tools; Ball Screws Part 2 nominal diameter and nominal leads Part 5 Connection dimensions for ball screw nuts DIN 69056 machine tools; Guide rails Part 1 dimensions for rectangular cross-section, form A; technical delivery conditions DIN 69063 Machine Tools - recordings for taper shanks For Part 1 Form A and Form C nach DIN 69893, connection dimensions Part 2 For type B and type D nach DIN 69893; Connecting dimensions Part 5 for type E to DIN 69893-5; Connecting dimensions Part 6 For Form F nach DIN 69893; Connecting dimensions DIN 69090 MQL machining technology Part 1: Terms and definitions Part 2 machine Part 3 tools and tooling systems DIN 69170 Mounted Points DIN 69513 machine tools; units, middle units for rotary table units and sizes DIN 69514 machine tools; units, rotary indexing table units Part 1 Form A and B sizes Part 2 Form C; Sizes DIN 69521 machine tools; units, middle units for transfer machines, sizes DIN 69522 machine tools; Units; Sites units for stand-units; Sizes DIN 69523 machine tools; units, units for sites carriage units; Sizes DIN 69524 machine tools; units, console units and sizes DIN 69525 machine tools; Units; Stand-units; Sizes DIN 69526 machine tools; Units; Carriage upright units; Sizes DIN 69572 machine tools; Units; Carriage units; Sizes DIN 69611 machine tools; units, support units for multi-spindle heads nach DIN 69001; Connecting dim DIN 69638 machine tools; Groove profiles and Nutenteilungen; Mass DIN 69639 machine tools; Cam to actuate series limit switches; Mass DIN 69641 machine tools; Units; Spindle units; Sizes DIN 69642 machine tools; Units; Rotating spindle units and sizes DIN 69643 machine tools; Units; Spindle units; Sizes
DIN 69718 Part 1 machine tools; External cylindrical grinding machines, concepts and terms DIN 69844 ANS end mills with straight shank Part 1 Dimensions Part 2 Technical delivery conditions DIN 69864 backplates for two-sided conical grinding wheels for hand grinders; Mass DIN 69871 NC shanks for automatic tool change Part 1 Form A, Form AD, type B and type with media DIN 69872 Pull studs for collet DIN 69873 volumes for tools and clamping devices; Dimensions of media and Their installation space DIN 69880 Tool holders with cylindrical shank Part 10 Type AK; Axial drive being coupled, Part 11 support for angle adjustment DIN 69881 toolHolder with prism Part 1 prism, prism recording; Technical delivery conditions Part 2 Form A with square cross Recording Part 3 of Form B with square longitudinal recording Part 4 Form C with square multi-shot Part 5 Form D with cylinder attachment DIN 69882 Tool holders with hollow taper shank to DIN 69893-1 Part 1 labeling scheme Technical delivery conditions Part 2 of Form A, arbor for cutters with transverse or longitudinal groove - Dimensions Part 3 of Form B, arbor with enlarged diameter for milling cutters contact with transverse groove - Dim Part 4 Form C, for parallel recording with side pulling face - Dimensions Part 5 Form D, for parallel recording with inclined flat - Dimensions Part 6 Form E, chuck for collets with setting angle 8 ° - Dimensions Part 7 of Form F, expansion chuck - Dimensions Part 8 Form G, shrink fit chucks - Dimensions DIN 69888 Auswuchtanforderungen of rotating tool systems DIN 69890 Modular tools; cantilever length of the recording modules Part 1 Acquisition Modules for spindle heads with taper 7: 24 nach DIN 2079 DIN 69893 Hollow taper shanks with flange contact Part 1 taper shanks type A and type C; Dimensions and design Part 2 taper shank type B; Dimensions and design Part 5 taper shanks type E; Dimensions and design Part 6 taper shanks type F; Dimensions and design Part 7 taper shanks type T for stationary tools; Dimensions and design
DIN 69894 taper shanks Verwechselsicherung - Form C, nach DIN 69893-1, and pictures for hollow tap nach DIN 69063-1: Shattered Dimensions
DIN 69895 central coolant supply for HSK - coolant pipe with threaded bushing taper shanks, DIN 698 69893-5 and type e to - Dimensions DIN 69900 Project Management - Network Analysis; Descriptions and terms
DIN 69901 project and project management Chapter 1 Basics Part 2 Processes, process model Part 3 methods Part 4 data, data model Part 5 terms DIN 69905 project economy - Project management - Vocabulary, Replaced by DIN 69901-1, DIN 69901 DIN 69909 multi-project management - management of project portfolios, programs and projects Chapter 1 Basics Part 2 Processes, process model DIN 70000-99999 [ Edit ]
DIN 70000 Road vehicles, vehicle dynamics and driving behavior; Terms DIN 70003 vibration stress; Measurement of characteristics of automotive components DIN 70005 vehicles Part 1 Graphical symbols for control devices and tacho graphs DIN 70006 Safety and Advice for vehicles Part 1 Safety and Advice for commercial vehicles DIN 70010 System of road vehicles, motor vehicles Terms for, Combinations of vehicles and trailers DIN 70011 superstructures for passenger cars; terms and concepts DIN 70014 vehicles for the transport of swap bodies Part 1 connection dimensions DIN 70019 Closure devices for removable tank and inland container; Minimum requirements DIN 70020 Road vehicles; Automotive Engineering Part 1: Road vehicles, motor vehicle; Terms of dimensions Part 2: Weights, WITHDRAWN without replacement in January 2006 Part 3: Test, maximum speed, acceleration and elasticity, mass, terms, Miscellaneous Part 5: tires and wheels, terms and conditions of measurement Part 6: Benefits, in April 1997 Replaced by DIN ISO 1585 Part 7: Engine mass of internal combustion engines in cars are driven did Exclusively by internal comb DIN 70024 terms for spare parts for motor vehicles and Their trailers Part 1 controls, display and control devices Part 3 brake equipment DIN 70027 Road vehicles, wheel alignment; Particulars to be chassis data, measurement conditions DIN 70028 Cars - measuring the stopping distance with ABS braking straight DIN 70030 motor vehicles; Determination of fuel consumption Part 1 cars, retired in May 1998 Part 2 trucks and buses DIN 70070 diesel engines - NOx reducing agent AUS 32 - Quality requirements
DIN 70073 Road vehicles - stability of vehicles with tipping bodies - air suspension semi-trailer with re construction
DIN 70852 locknuts; Mass
DIN 70907 Piston rings for mechanical engineering; Test of quality characteristics; Concepts, methods Supplements to DIN ISO 6621 Part 2
DIN 70908 Piston rings for mechanical engineering; Quality conditions; Visual cues, marking; Supplem 6621 Part 5 DIN 70952 Tab washers for nuts nach DIN 70852 DIN 71405 hissing valves, taps hissing; Connecting dimensions; Automotive Engineering DIN 71412 Taper type grease nipple (formerly Kegelwulstschmierköpfe) DIN 71420 Central lubrication; Survey DIN 72552 terminal designation in motor vehicles Part 1 Purpose, Principles, requirements Part 2 meanings Part 3 Applications in connection diagrams Part 4 Overview Part 5 System and function names (Withdrawn draft) DIN 72609 construction lights, with ball caster and Accessory Shoe (invalid) DIN 72616 reflectors (invalid) DIN 72616 round reflectors DIN 72701 horns, invalid DIN 72701 Sounders; Serve horns for low voltage DIN 72758 Dimmer Part 1 Electrical dimmer switch, without and with horn push button for motorcycles and motorcycles (i Part 2 Mechanical dimmer switch, without and with horn push button for motorcycles and motorcycles Part 3 foot dimmer switch for rise and screws (invalid) DIN 72759 Brake Light Switch Part 1 brake light rotary switch. (Invalid) Part 2 brake light switch, mechanical, rated voltage up to 24V Part 3 hydraulic brake light switch. WITHDRAWN September 1990 (invalid) Part 5 brake light switch, pneumatic Part 6 brake light switch, hydraulic with metric ISO thread M12 x 1 DIN 73021 Designation of the direction of rotation of the cylinder and the ignition of motorcar DIN 73378 Pipes made of polyamide for motor vehicles DIN 73411 coolant lines in motor vehicles - Hoses and hose bend Part 1 dimensions, materials, labeling Part 2 requirements, testing DIN 74074 saddle pads Part 1 saddle covers for motorcycles Part 2 saddle pads for the front calipers for motorcycles DIN 74310 air brake systems; Hoses Part 1 dimensions, material, marking Part 2 requirements, tests DIN 74313 soldering compression fittings
Part 1 Straight Male, Type A and B Part 2 Just stub, Form C and D DIN 74315 soldering compression fittings - angle nozzle DIN 74317 soldering compression fittings - T-connector DIN 74319 soldering compression fittings - Cross nozzle DIN 74323 air brake systems, coiled tubing DIN 74324 air brake systems - tubes and pipes made of polyamide Part 1 Requirements and tests DIN 74704 Snake valve body DIN 75079 emergency medical vehicles (NEF) - Definitions, requirements, testing DIN 75200 Determination of burning behavior of materials used in automotive interior trim DIN 75201 fogging test of materials used in vehicle interiors DIN 75203 Fully automatic central lubrication system for commercial vehicles DIN 75204 Road vehicles, traffic accident reconstruction and injury mechanism Part 1: Terms of accident reconstruction Part 2 concepts to various types of tracks and track features Part 3 features for data collection DIN 75220 aging of automotive components in solar simulation system DIN 75302 Roof rack for cars; Safety requirements, testing DIN 75400 closure devices of safety belts in cars DIN 75405 Fire Extinguisher Brackets for passenger cars; Requirements, testing, DIN 75406 mounts for first aid material in passenger cars; Requirements, testing, DIN 75407 warning triangle brackets in passenger cars; Requirements, testing, DIN 75410 Securing of loads on road vehicles
Part 1 Lashing points on utility vehicles for the carriage of goods and having a maximum mass not exc Minimum requirements DIN 76033 tow ropes for passenger cars; Requirements, testing, monitoring DIN 76051 Part 1 chocks for motor vehicles and trailers Part 2 wheel chocks for farm vehicles; Functional dimensions DIN 77200 security services - Requirements DIN 77700 Wage Tax Services DIN 77800 quality requirements for providers of residential shape assisted living for the elderly DIN 79012 Thread for bicycles and mopeds - Theoretical values, thread limit dimensions (draft) DIN 79105 BMX bicycles; Concepts safety requirements, testing, DIN 81208 maneuvering of ships Part 1: General concepts, quantities and test conditions Part 2: Flow test Part 3: Ausschwingversuch Part 4: Acceleration trial Part 5: Turning circletest
Part 6: Three test from standstill Part 7: Reverse attempt Part 8: Schlängelversuch (Z-test) Part 9: Sine test Part 10: Spiral attempt by Bech Part 11: Spiral attempt by Dieudonné Part 12: stop test Part 13: Traversierversuch Part 14: Wedel attempt; Text in German and English Part 15: Mäanderversuch Part 16: overshoot attempt in the vertical plane Part 17: Test for deterministic mining the lift and torque-free travel Part 18: Test for deterministic mining the critical velocity Part 23: rotation experiment with spotlights Part 24: Attempt to change course Part 25: evasion trial Part 26: Person Overboard trial DIN 81249 Corrosion of metals in sea water and sea atmosphere Part 1 Definitions, principles; Text in German and English Part 2 Free corrosion in seawater Part 3 galvanic corrosion in seawater; Text in German and English Part 4 Corrosion in sea atmosphere DIN 82101 Components for lifting towing, lashing - Shackle straight - Carbon steel quality DIN 83202 Ladders on ships Part 1 Lightweight, Part 2 Moderate Type Part 3 Heavy design Part 4 holder (draft) DIN 86008 steel tubes for marine pipelines Part 1 selection and overview of seamless and welded pipes, January 1998 WITHDRAWN without repla
Part 2 selection and overview of seamless and welded precision steel tubes, January 1998 WITHDRAW replacement DIN 86056 tube grommets with union nut and ring for pipes made of steel or copper and wrought cop DIN 86057 Welding flanges for Implementing nozzle DIN 86059 implementation neck flanges, steel tubes, nominal pressure 10 DIN 86061 connector sockets with pipe flange for steel pipes, nominal pressure 10 DIN 86064 connector sockets with pipe flange and welding flange, steel tubes, nominal pressure 10 DIN 86066 Cast steel check valves for Einschweißkrümmer - DN 50 to DN 150, flange PN 10 DIN 86720 V-flat slide made of bronze with head and flanges DN 20 to DN 100, PN 16 DIN 86735 oil-water separators - Tank system for bilge water on seagoing vessels DIN 87101 check valves, self-closing, vertical design, DN 50 to DN 150, PN 1 - PN 10 flanges nach
DIN 87151 filters; Cast iron strainer, NW 40 to 200, nominal pressure 2.5, with Flanschanschlußmaßen pressure 10 Part 1 compilation and connection dimensions Part 2 BOM DIN 87152 cast iron strainer; Housing Part 1 straight through Part 2 Angular shape DIN 87153 cast iron strainer; Cover DIN 87154 cast iron strainer; Baskets DIN 87155 cast iron strainer; Sealing rings DIN 87160 Suction strainers made of metal, DN 20 to DN 200 Part 1 compilation Part 2 items DIN 87303 square drive with tapered and parallel sides for valves for shipboard DIN 87308 Operating parts for valves for shipboard use - Crank handles with square hole with tapered DIN 87310 multi-purpose key with female square and flat edge DIN 87311 Handradschlüssel DIN 87312 flat edge-mortise locks for top filling and Peilrohrleitungen DIN 87314 square mortise for drain fittings DIN 87340 Drill pipe remotes; nominal sizes of Component Parts DIN 87341 Drill pipe remotes; Installation DIN 87343 Drill pipe remotes; Einschweißgelenke DIN 87344 Drill pipe remotes; Aufsteckgelenke DIN 87346 Drill pipe remotes; Stock DIN 87349 Drill pipe remotes; Kegelradtriebe DIN 87350 Drill pipe remotes; Swivel angle drives DIN 87351 Drill pipe remotes; Spindle extensions, plug-on pipe sockets, square Einschweißzapfen DIN 87352 Drill pipe remotes; Protective covers for pivoting angle drives DIN 87371 Drill pipe remotes; drill pipe holder DIN 87373 Drill pipe remotes, Bushings, waterproof DIN 87374 Drill pipe remotes, keypads Weld on deck, with wave square pin DIN 87380 Drill pipe remotes; Aufsteckgelenke, disengageable DIN 87381 Drill pipe remotes; Stem Extensions Straight square, slip-on pipe sockets, square Einschwe DIN 87382 Drill pipe remotes; Bushings with angle drive, waterproof DIN 87383 Drill pipe remotes; Between control points DIN 87384 Drill pipe remotes, control points on the wall, folding DIN 87721 Drain Fittings Part 1 compilation, installation Part 2 drain plugs, welding plates DIN 87901 air valves for pumps DIN 92111 Guidelines for Tropical tests
DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN
95360 elastomer spring elements - Technical Specification 95361 elastomer spring elements - rails 95362 elastomer spring elements, hollow prismatic 95363 elastomer spring elements, cylindrical, Forms A to F 95364 elastomer spring elements - Buffer, forms A to G 95365 elastomer spring elements - Hats Camp - Forms A to K 95366 elastomer spring elements - Pot bearings with and without breakaway, forms A to G 95367 elastomer spring elements - Roof-bearing forms A and B 95368 elastomer spring elements - cone-bearing forms A to C 95369 elastomer spring elements - cap stock form A 96110 Medical instruments - Technical specification for reference samples 96166 Medical instruments - hook grip for wire saw after Gigli EN 1-999 [ Edit ]
DIN EN 1 Stoves for liquid fuels with vaporizing burners and flue connection DIN EN 2 Fire classes DIN EN 3 Portable fire extinguishers DIN EN 14 Dimensions of bed blankets DIN EN 19 Industrial valves - Marking of metallic valves DIN EN 26 Gas-fired instantaneous water heaters for sanitary use with atmospheric burners DIN EN 31 Floor-standing wash basins - Connecting dimensions DIN EN 32 Wall-mounted washbasins - Connecting dimensions DIN EN 33 Floor-standing WC pans with cistern - Connecting dimensions DIN EN 34 Toilet bowls, wall hung with cistern - Connecting dimensions DIN EN 35 Floor-standing bidets with inlet from above - Connecting dimensions DIN EN 36 Wall-mounted bidets with inlet from above - Connecting dimensions DIN EN 37 Floor-standing WC pans with independent water supply - Connecting dimensions DIN EN 38 wall hung WC pans with independent water supply - Connecting dimensions DIN EN 40 Lighting columns Part 1 Definitions and nomenclature Part 2 General requirements and dimensions DIN EN 54 Fire alarm systems Part 1 Introduction Part 2 fire alarm panels Part 3 Fire alarm devices - Sounders Part 4 power supplies Part 5 heat detectors; Point detectors Part 7 Smoke detectors - Point detectors using scattered light, trans mitted light or ionization Part 10 Flame detectors; Point detectors Part 11 Manual fire alarm Part 12 Smoke detectors - Line detectors using optical beam to
Part 13 Compatibility assessment of system components Part 16 Voice alarm control Part 17 Short circuit isolators Part 18 input / output devices Part 20 Aspirating Part 21 transmission facilities for fire and fault messages Part 23 Fire alarm devices - Visual Signaling Part 24 components for voice alarm systems - Loudspeakers Use part 25 components, the high frequency compounds DIN EN 58 Bitumen and bituminous binders - Sampling bituminous binders DIN EN 59 glass fiber reinforced plastics; Determination of hardness with the Barcol hardness tester EN 71 Toy Safety Part 1 Mechanical and physical properties Part 2 Flammability Part 3 Migration of Certain elements Part 4 Experimental sets for chemistry and related activities Part 5 Chemical toys (sets) other than experimental sets Part 6 Graphical symbol for age warning notice to Part 7 Finger paints; Requirements and test methods Part 8 swings, slides and similar activity toys for domestic use (indoor and outdoor) Part 9 Organic chemical compounds - Requirements Part 10 Organic chemical compounds - Sample preparation and extraction Part 11 Organic chemical compounds - Analytical Methods DIN EN 73 wood preservatives; Accelerated aging of Treated wood prior to biological testing; Evaporat DIN EN 74 Couplers, spigot pins and base plates for use in falsework and scaffolds Part 1 tubes - Requirements and test methods Part 2 Special couplers - Requirements and test methods Part 3 Plain base plates and spigot pins - Requirements and test methods DIN EN 76 Packaging for prepackaged foods of Certain; volume of packaging made ??of glass and met DIN EN 80 Wall-hung urinals - Connecting dimensions DIN EN 81 Safety rules for the construction and installation of lifts DIN EN 84 Wood preservatives - Accelerated aging of Treated wood prior to biological testing - Leachin DIN EN 88 Pressure regulators and associated safety devices for gas appliances Part 1 Pressure regulators for inlet surrounding pressures up to and Including 50 kPa Part 2 Pressure regulators for inlet surrounding pressures above 500 mbar up to and Including 5 bar DIN EN 89 gas-fired storage water heaters for sanitary use DIN EN 107 test methods for windows; Mechanical tests DIN EN 111 Wall mounted wash hand basins - Connecting dimensions, October 2011 Replaced by EN 3
DIN EN 113 Wood preservatives - Test method for deterministic mining the protective effectiveness ag destroying basidiomycetes - Determination of the effectiveness DIN EN 115 Safety of escalators and moving walkways
Part 1 Design and Installation DIN EN 116 diesel and domestic heating fuels - Determination of cold filter plugging
DIN EN 117 Wood preservatives - Determination of the toxic values ??against Reticulitermes species ( (laboratory method)
DIN EN 118 Wood preservatives - Determination of preventive action against Reticulitermes species (E (laboratory method) DIN EN 120 woody materials; Determination of formaldehyde content; extraction method called perfo DIN EN 124 tops and manhole tops for pedestrian areas - Design requirements, testing, marking, qual DIN EN 125 Flame supervision devices for gas appliances - Thermo-electric flame DIN EN 126 Multifunctional controls for gas appliances DIN EN 130 test methods for doors; Examination of the stiffness of the door leaves by repeated torsio DIN EN 131 Heads Part 1 terms, types, functional sizes Part 2 Requirements, testing, marking Part 3 User Information Part 4 single- or multi-joint ladders DIN EN 132 Respiratory protective devices - Definitions of terms and pictograms DIN EN 133 Respiratory protective devices - Classification DIN EN 134 Respiratory protective devices - Nomenclature of components DIN EN 135 Respiratory protective devices - List of equivalent terms DIN EN 136 Respiratory protective devices - Full face masks - Requirements, testing, marking
DIN EN 137 Respiratory protective devices - contained open-circuit compressed air (SCBA) with a full f Requirements, testing, marking
DIN EN 138 Respiratory protective devices - fresh air hose breathing apparatus with full face mask, ha mouthpiece assembly - Requirements, testing, marking DIN EN 140 Respiratory protective devices - Half masks and quarter masks - Requirements, testing, m DIN EN 142 Respiratory protective devices - Mouthpiece assemblies - Requirements, testing, marking DIN EN 143 Respiratory protective devices - Particle filters - Requirements, testing, marking DIN EN 144 Respiratory protective devices - Gas cylinder valves Part 1 threaded connections for insert Part 2 threaded connection at the outlet connection Part 3 threaded connections at the output port for diving gases Nitrox and oxygen
DIN EN 145 Respiratory protective devices - breathing apparatus compressed oxygen or compressed o type - Requirements, testing, marking DIN EN 148 Respiratory protective devices - Threads for face pieces Part 1 connection thread Part 2 central threaded connection Part 3 threaded connection M 45 × 3
DIN EN 149 Respiratory protective devices - Filtering half masks to protect against particles - Requirem marking
DIN EN 152 Wood preservatives - Determination of the protective effectiveness of a preservative treat stain - Laboratory method
DIN EN 153 Methods of measurement of energy consumption of electric mains operated and related p refrigerators, freezers, freezers and Their Combinations DIN EN 161 Automatic shut-off valves for gas burners and gas appliances DIN EN 166 Personal eye protection DIN EN 167 Personal eye protection - Optical test methods DIN EN 168 Personal eye-protection - Non-optical test methods DIN EN 169 Personal recommended use DIN EN 170 Personal DIN EN 171 Personal DIN EN 172 Personal DIN EN 174 Personal DIN EN 175 Personal
eye protection - Filters for welding and related techniques - Transmittance requir
eye protection - Ultraviolet filters - Transmittance requirements and recommende eye protection - Infrared filters - Transmittance requirements and recommended eye protection - sun protection filters for industrial use eye protection - Ski goggles for downhill skiing protection - Equipment for eye and face protection During welding and allied Pro
DIN EN 179 Building hardware - Emergency exit locks with handle or push pad for use on escape route and test methods DIN EN 196 Methods of testing cement Part 1 Determination of strength Part 2 Chemical analysis of cement Part 3 Determination of setting time and soundness Part 5 Examination of pozzolanic cements of Pozzolanicity Part 6 Determination of fineness Part 7 Methods of taking and preparing samples of cement Part 8 hydration - Solution method Part 9 of hydration - Semi-adiabatic method Part 10 Determination of water-soluble chromium (VI) in cement DIN EN 197 cement Part 1 Composition, specifications and conformity criteria for common cements Part 2 of conformity assessment DIN EN 198 Sanitary appliances - Baths made from crosslinked cast acrylic sheets - Requirements and DIN EN 200 Sanitary tapware - Single taps and mixers (PN 10) - General technical specifications DIN EN 201 Plastics and rubber machines - Injection molding machines - Safety requirements DIN EN 204 Classification of thermoplastic wood adhesives for non-structural applications DIN EN 205 Adhesives - Wood adhesives for non-structural applications - Determination of shear stren DIN EN 206 concrete Part 1 Specification, performance, production and conformity, July 2014 Replaced by DIN EN 206 Part 9 Supplementary rules for self-compacting concrete (SCC), July 2014 Replaced by DIN EN 206 DIN EN 207 Personal eye protection - Filters and eye-protectors against laser radiation (laser eye-prote DIN EN 208 Personal eye protection - Eye protectors for adjustment work on lasers and laser systems
DIN EN 212 Wood preservatives - General guidance for sampling and sample preparation of wood pres Treated timber for analysis DIN EN 215 Thermostatic radiator valves - Requirements and testing
DIN EN 225 atomizing oil burners - Connecting dimensions for oil burner pumps and oil burner motors Part 1 oil burner pumps Part 2 oil burner motors DIN EN 226 atomizing oil burners; Connecting dimensions between burners and heat generators DIN EN 228 Automotive fuels - Unleaded petrol - Requirements and test methods DIN EN 230 burner control systems for oil burners, September 2012 Replaced by DIN EN 298 DIN EN 232 Baths - Connecting dimensions DIN EN 233 Wallcoverings in roll form - Specification for finished paper, vinyl and plastic wallcoverings DIN EN 234 Wallcoverings in roll form - Specification for wallcoverings for subsequent offer treatment DIN EN 235 Wallcoverings - Vocabulary and symbols
DIN EN 237 Liquid petroleum products - petrol - Determination of low lead by atomic absorption spect Concentrations DIN EN 238 Liquid petroleum products - petrol - Determination of benzene content by infrared spectro DIN EN 241 Liquid petroleum products - Determination of sodium content - Atomic Absorption Spectro DIN EN 246 Sanitary tapware - General specifications for flow regulator DIN EN 247 Heat exchangers - Terminology DIN EN 248 Sanitary tapware - General specification for electrodeposited Ni-Cr coatings
DIN EN 249 Sanitary appliances - Shower trays made from crosslinked cast acrylic sheets - Requireme methods
DIN EN 250 Respiratory equipment - Self-contained diving apparatus with compressed air - Requireme DIN EN 251 shower trays; Connecting dimensions
DIN EN 252 Wood preservatives; Field test method for deterministic mining the relative protective effe preservative in ground contact
DIN EN 253 District heating pipes - Pre-insulated bonded pipe systems for Directly buried hot water ne System Consisting of steel service pipes, polyurethane thermal insulation and outer casing of polyeth DIN EN 257 Mechanical thermostats for gas appliances DIN EN 259 Wallcoverings in roll - high claimable wallcoverings Part 1 requirements Part 2 Determination of puncture resistance DIN EN 263 Sanitary appliances - Crosslinked cast acrylic sheets for baths and shower trays for domes DIN EN 266 Wallcoverings in roll; Specification for textile wallcoverings DIN EN 267 Automatic forced draft burners for liquid fuels
DIN EN 269 Respiratory protective devices - Powered fresh air hose breathing apparatus Incorporating Requirements, testing, marking DIN EN 274 Waste fittings for sanitary appliances Part 1 requirements Test methods Part 2 Part 3 quality monitoring DIN EN 275 Wood preservatives; Determination of the protective effectiveness against marine organis DIN EN 277 Sacks for the transport of food for the food aid - Sacks made of woven polypropylene fabr DIN EN 280 Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Sa
DIN EN 283 swap body; Examination DIN EN 284 swap bodies - Non-stackable swap bodies of class C - Dimensions and general requiremen DIN EN 285 Sterilization - Steam sterilizers - Large sterilizers DIN EN 286 Simple unfired pressure vessels for air or nitrogen Part 1 pressure vessels for general purposes Part 2 pressure vessels for air braking and auxiliary systems for motor vehicles and Their trailers Part 3 steel pressure vessels for air braking and auxiliary pneumatic equipment for railway vehicles Part 4 pressure vessels of aluminum alloys for air braking and auxiliary pneumatic equipment for railw DIN EN 287 testing of welders - Fusion welding Part 1 Steels Part 6 cast iron DIN EN 289 Plastics and rubber machines - Presses - Safety requirements DIN EN 293 Oil pressure atomizing nozzles; minimum requirements, tests
DIN EN 294 Safety distances to prevent prevention danger zones being reached by the upper limbs, Ju by DIN EN ISO 13857 DIN EN 295 stoneware pipe systems for drains and sewers Part 1 Specifications for pipes, fittings and connections Part 2 Evaluation of conformity and sampling Part 3 test methods Part 4 requirements for adapters, connectors and flexible couplings Part 5 Requirements for perforated pipes and fittings Part 6 Requirements for components for Manholes and inspection shafts Part 7 Requirements for pipes and joints for pipe jacking DIN EN 70 kW DIN EN DIN EN DIN EN
297 boilers for gaseous fuels - Boilers of the type B with atmospheric burners of nominal heat 298 burner control for burners and appliances burning gaseous fuels or liquid 299 Oil pressure atomizing nozzles 300 plates of long, flat, Oriented beach (OSB) - Definitions, classification and requirements
DIN EN 301 Adhesives for load-bearing timber structures - phenolic resins and amino - Classification a requirements DIN EN 302 Adhesives for load-bearing timber structures - Test methods Part 1 Determination of longitudinal tensile shear strength Part 2 Determination of resistance to delamination
Part 3 Determination of the effect of acid damage to wood fibers by temperature and humidity cycling tensile strength Part 4 Determination of the effects of wood shrinkage on the shear strength Part 5 Determination of the maximum waiting time at reference conditions Part 6 Determination of the pressing time at reference conditions Part 7 Determination of service life at reference conditions DIN EN 303 boiler Part 1 boilers with forced draft burners, Terms, general requirements, testing and marking Part 2 boilers with forced draft burners; Special requirements for boilers with atomizing oil burners
Part 3 central heating boilers burning gas - Assembly Comprising a boiler and burner blower
Part 4 boilers with forced draft burners; Special requirements for boilers with forced draft oil burners w kW and a maximum operating pressure of 3 bar, Terms, special requirements, testing and marking
Part 5 boilers for solid fuels, manually and Automatically stoked, nominal heat output up to 500 kW - T requirements, testing and marking
Part 6 boilers with forced draft burners; Specific requirements for the domestic hot water of operation boilers with atomizing oil burners of nominal heat output not exceeding 70 kW
Part 7 central heating boilers for gaseous fuels with a smaller jet burner with a nominal heat output th KW DIN EN 304 boilers - Test code for heating boilers with atomizing oil burners DIN EN 305 Heat exchangers - Definitions and general requirements for the test to mine deterministic DIN EN 306 heat exchanger - measurements and accuracy in the determination of performance
DIN EN 307 heat exchangers - Guidelines for the preparation of the installation and operating instruct maintenance instructions for Obtaining the performance of heat exchangers of all types
DIN EN 308 Heat exchangers - Methods of measuring the performance criteria of air / air and air / flue system DIN EN 309 Particle boards - Definition and classification DIN EN 310 Wood-based panels - Determination of flexural modulus and flexural strength DIN EN 311 Wood-based panels - Surface soundness - Test methods DIN EN 312 Chipboard - Requirements DIN EN 313 Plywood - Classification and terminology Part 1 classification Part 2 Terminology DIN EN 314 Plywood - Bonding quality Test methods Part 1 Part 2 requirements DIN EN 315 Plywood - Tolerances DIN EN 316 Fibreboard - Definition, classification and symbols DIN EN 317 chipboard and fibreboard; Determination of swelling in thickness after immersion in water DIN EN 318 Wood-based panels - Determination of dimensional changes associated with changes in re DIN EN 319 particleboard and fibreboard - Determination of tensile strength perpendicular to faces DIN EN 320 particleboard and fibreboard - Determination of resistance to axial withdrawal of screws DIN EN 321 woody materials; Determination of moisture resistance under cyclic test DIN EN 322 woody materials; Determination of moisture content DIN EN 323 woody materials; Determination of bulk density DIN EN 324 woody materials; Determination of dimensions of boards Part 1 Determination of thickness, width and length Part 2 Determination of planarity and edge straightness DIN EN 325 Wood-based panels - Determination of dimensions of test pieces DIN EN 326 Wood-based panels - Sampling, cutting and inspection Part 1 Sampling and cutting of test pieces and expression of test Part 2 Initial type testing and factory production control
Part 3 of Inspection of isolated lot of panels DIN EN 327 Heat exchangers - Forced convection air condensers - Test methods for Establishing the p DIN EN 328 Heat exchangers - Methods of measuring the performance criteria of fan air coolers
DIN EN 330 Wood preservatives; Field experiment to deterministic mine the relative effectiveness of a for use under a coating and no ground contact: L-connection method DIN EN 331 Manually operated ball valves and stopcocks closed bottom for domestic gas installations DIN EN 334 gas pressure regulators for inlet surrounding pressures up to 100 bar
DIN EN 335 Durability of wood and wood products - use classes: Definitions, Application to solid wood DIN EN 336 Structural timber - Dimensions, tolerances DIN EN 338 Structural timber - Strength classes DIN EN 340 Protective clothing - General requirements DIN EN 341 Personal fall protection equipment - Descender devices for rescue DIN EN 342 Protective clothing - clothing and garments for protection against cold DIN EN 343 Protective clothing - Protection against rain DIN EN 344 Safety, protective and occupational footwear for professional use Requirements and test methods Part 1, October 2004 Replaced by DIN EN ISO 20344 ... DIN EN ISO 20
Part 2 Additional requirements and test methods, Oct. 2004 Replaced by DIN EN 15090, DIN EN ISO 20 17249 DIN EN 345 Safety footwear for professional use Part 1 specification, Oct. 2004 Replaced by DIN EN ISO 20345 Part 2 Additional specification, Oct. 2004 Replaced by DIN EN 15090, DIN EN ISO 20345 and DIN EN IS DIN EN 346 Protective footwear for professional use Part 1 specification, Oct. 2004 Replaced by DIN EN ISO 20346 Part 2 Additional specification, Oct. 2004 Replaced by DIN EN ISO 20346 DIN EN 347 occupational footwear for professional use Part 1 specification, Oct. 2004 Replaced by DIN EN ISO 20345 Part 2 Additional specification, Oct. 2004 Replaced by DIN EN ISO 20347 DIN EN 349 Safety of machinery - Minimum gaps to avoid crushing of parts of the body DIN EN 350 Durability of wood and wood products - Natural durability of solid wood Part 1 Principles of testing and classification of the natural durability of wood Part 2 Guide to natural durability and treatability of selected wood species of importance in Europe DIN EN 351 Durability of wood and wood products - Treated with wood preservatives solidwood DIN EN 352 Hearing protectors DIN EN 353 Personal protective equipment against case Part 1 case arresters Including a rigid anchor line Part 2 Guided type event arresters Including a flexible anchor DIN EN 354 Personal protective equipment against falls - Lanyards DIN EN 355 Personal protective equipment against falls - shock absorber DIN EN 356 Glass in building - Security glazing - Testing and classification of resistance against manua
DIN EN 357 Glass in building - Fire resistant glazed transparent or translucent glass products - Classifi resistance
DIN EN 358 Personal retaining straps DIN EN 360 Personal DIN EN 361 Personal DIN EN 362 Personal DIN EN 363 Personal DIN EN 364 Personal
protective equipment for work positioning and prevention of falls - Belts and con protective protective protective protective protective
equipment equipment equipment equipment equipment
against against against against against
falls falls falls falls falls
-
Hörsicherungsgeräte Harnesses Fasteners Personal falling Systems Test methods
DIN EN 365 Personal protective equipment against falls - General requirements for instructions for use periodic Überprung, IH, labeling and packaging
DIN EN 367 Protective clothing; Protection against heat and flame; Test method: Determination of hea exposure to flame
DIN EN 370 Wood preservatives; determination based on the slip prevention suppressive activity agai punctatum (De Geer) DIN EN 374 Protective gloves against chemicals and micro-organisms Part 1 Terminology and performance requirements Part 2 Determination of resistance to penetration Part 3 Determination of resistance to permeation by chemicals
DIN EN 377 lubricants for use in devices and the associated control devices for fuel gases except thos for Use in Industrial Processes DIN EN 378 Refrigerating systems and heat pumps - Safety and environmental requirements Part 1 Basic requirements, definitions, classification and selection criteria Part 2 design, manufacture, testing, marking and documentation Part 3 site and personal protection Part 4 operation, maintenance, repair and recovery DIN EN 379 Personal eye protection - Automatic welding filters DIN EN 380 Timber structures; test methods; General principles for testing under static loads DIN EN 381 Protective clothing for users of hand-held chainsaws Part 1 Test rig for testing resistance to cutting by a chainsaw Part 2 Test method for leg protection Part 3 Methods of test for footwear Part 4 test methods for protective gloves for chain saws Part 5 Requirements for leg protection Part 7 requirements for protective gloves for chain saws Part 8 test methods for protective gaiters for chain saws Part 9 requirements for protective gaiters for chain saws Part 10 Test methods for upper body protectors Part 11 requirements for upper body protectors DIN EN 382 sheets of fibreboard; Determination of surface absorption Part 1 Test methods for fibreboard nach the dry method Part 2 Test method for hard disks
DIN EN 383 Timber structures - Test methods - Determination of embedding strength and foundation v type fasteners
DIN EN 384 Structural timber - Determination of characteristic values ??of mechanical properties and DIN EN 385 finger joints in timber - Performance requirements and minimum production requirements DIN EN 386 Glued laminated timber - Performance requirements and minimum production requiremen
DIN EN 387 Glued laminated timber - Large finger joints - Performance requirements and minimum pr requirements DIN EN 388 Protective gloves against mechanical risks DIN EN 390 Glulam - Dimensions - Tolerances DIN EN 391 Glued laminated timber - Delamination of adhesive joints DIN EN 392 Glued laminated timber - Shear test of glue lines DIN EN 397 Industrial safety helmets
DIN EN 402 Respiratory protective devices - Automatic tion contained open-circuit compressed air (SC mask or mouthpiece assembly for escape - Requirements, testing, marking
DIN EN 403 Respiratory protective devices for self-rescue - Filtering devices with hood for escape from testing, marking
DIN EN 404 Respiratory protective devices for self-rescue - filter self-rescuer with mouthpiece assemb against carbon monoxide
DIN EN 405 Respiratory protective devices - Filtering half masks with valves to protect against gases o particles - Requirements, testing, marking DIN EN 407 Protective gloves against thermal risks (heat and / or fire)
DIN EN 408 Timber structures - Structural timber and glued laminated timber - Determination of some mechanical properties DIN EN 409 Timber structures - Test methods - Determination of the yield moment of dowel type faste DIN EN 410 Glass in building - Determination of luminous and solar technical characteristics of glazing DIN EN 413 Masonry cement Part 1 Composition, specifications and conformity criteria Test methods Part 2 DIN EN 415 Safety of packaging machines Part 1 Terminology and classification of packaging machines and related equipment Part 2 packaging machines for preformed rigid containers Part 3 form, fill and seal machines Part 4 palletizer and Depalletizer Part 5 wrapping machines Pallet wrapping machines Part 6 Part 7 multiple packing machines Part 8 strapping machines
Part 9 Noise measurement methods for packaging machines, packaging lines and associated equipme 2 and 3 DIN EN 416 gas heater - dark radiator with a forced draft burners for domestic use Part 1 Safety Part 2 Rational use of energy
DIN EN 417 Non-refillable metallic cartridges for liquefied gas with or without a valve for use with port manufacture, inspection, testing and marking
DIN EN 418 Safety of machinery, emergency stop equipment, functional aspects, principles, March 20 EN ISO 13850 DIN EN 419 luminous radiant burners without a fan for commercial and industrial applications Part 1 Safety Part 2 Rational use of energy DIN EN 420 Protective gloves - General requirements and test methods DIN EN 421 Protective gloves against ionizing radiation and radioactive contamination DIN EN 422 Plastics and rubber machines - Blow molding machines - Safety requirements DIN EN 424 Resilient floor coverings - Determination of the effect of the simulated movement of a furn DIN EN 425 Resilient and laminate floor coverings - Castor chair test DIN EN 432 Resilient floor coverings - Determination of shear strength DIN EN 437 Test gases - Test surrounding pressures - Appliance categories
DIN EN 438 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually Part 1 Introduction and general information Part 2 Determination of properties
Part 3 Classification and specifications for laminates with a thickness less than 2 mm provided for bon Part 4 Classification and specifications for compact laminates with a thickness of 2 mm and greater
Part 5 Classification and specifications for laminates for floors with a thickness of less than 2 mm prov substrates to a Part 6 Classification and specifications for compact laminates for use outdoors with a thickness of 2 m Part 7 Compact laminate and HPL composite panels for wall and ceiling finishes for interior and exteri Part 8 Classification and specifications for design laminates Part 9 Classification and specifications for alternative core laminates structure DIN EN 442 radiators and convectors Part 1 Technical specifications and requirements Part 2 Test methods and rating Part 3 of conformity assessment DIN EN 443 Fire Helmets for fire fighting in buildings and other structures DIN EN 444 Non-destructive testing; Basics for radiographic testing of metallic materials using X-rays DIN EN 445 Grout for prestressing tendons - Test methods DIN EN 446 Grout for prestressing tendons - Grouting DIN EN 447 Grout for prestressing tendons - General requirements
DIN EN 448 District heating pipes - Pre-insulated bonded pipe systems for Directly buried hot water ne assemblies of steel service pipes Consisting, polyurethane thermal insulation and outer casing of poly
DIN EN 449 requirements for liquefied petroleum gas appliances - Domestic flueless space heaters (in catalytic combustion heaters) DIN EN 450 Fly ash for concrete Part 1 Definition, specifications and conformity criteria Part 2 of conformity assessment DIN EN 451 test methods for fly ash
Part 1 Determination of free calcium oxide content Part 2 Determination of fineness by wet sieving DIN EN 452 Swap bodies - Swap bodies of Class A - Dimensions and general requirements DIN EN 453 Food processing machinery - Dough mixers - Safety and hygiene requirements DIN EN 454 Food processing machinery - Planetary mixers - Safety and hygiene requirements DIN EN 455 Medical gloves for single use Part 1 Requirements and testing for leaks Part 2 Requirements and testing for physical properties Part 3 Requirements and testing for biological evaluation Part 4 Requirements and testing for shelf life determination DIN EN 457 Safety of machinery; Auditory danger signal December 2005 Shall TO BE REPLACED DIN E DIN EN 458 Hearing protectors - Recommendations for selection, use, care and maintenance DIN EN 459 Building lime Part 1 Definitions, specifications and conformity criteria Test methods Part 2 Part 3 of conformity assessment
DIN EN 460 Durability of wood and wood products - Natural durability of solid wood - Guide to the dur are for wood to be used in hazard classes
DIN EN 461 Specification for dedicated liquefied petroleum gas appliances - Flueless non-domestic sp exceeding 10 kW DIN EN 462 Non-destructive testing; Image quality of radiographs Part 1 Image quality indicators (wire type); Determination of image quality value Part 2 Image quality indicators (step / hole type); Determination of image quality value Part 3 Image quality classes for ferrous metals Part 4 Experimental determination of image quality values ??and image quality tables Part 5 Image quality indicators (duplex wire type), determination of image blur
DIN EN 464 Protective clothing - Protection against liquid and gaseous chemicals, aerosols and solid p liquid - Test method: Determination of leak-tightness of gas-tight suits (internal pressure test) DIN EN 469 Protective clothing for firefighters - Performance requirements for protective clothing for fi DIN EN 470 Protective clothing for use in welding and allied Processes Part 1 General requirements, January 2008 Replaced by DIN EN ISO 11611 DIN EN 471 high visibility clothing - Test methods and requirements DIN EN 472 Pressure gauges - Vocabulary DIN EN 474 Earth-moving machinery - Safety Part 1: General requirements Part 2 Requirements Grading Part 3 Requirements for loaders Part 4 Requirements for backhoe loaders Part 5 Requirements for hydraulic excavators Part 6 Requirements for dumpers Part 7 Requirements for scrapers Part 8 Requirements for graders
Part 9 requirements for Rohrverleger Part 10 requirements for grave milling Part 11 Requirements for earth and landfill compactors Part 12 requirements for cable excavator DIN EN 476 General requirements for components used in drains and sewers
DIN EN 477 profiles unplasticized polyvinyl chloride (PVC-U) for manufacture of windows and doors - D puncture resistance of main profiles by dart
DIN EN 478 profiles unplasticized polyvinyl chloride (PVC-U) for manufacture of windows and doors - D behavior after storage at 150 ° C - Test methods
DIN EN 479 profiles unplasticized polyvinyl chloride (PVC-U) for manufacture of windows and doors - D thermal shrinkage DIN EN 480 Admixtures for concrete, mortar and grout - Test methods Part 1 Reference concrete and reference mortar for testing Part 2 Determination of setting time Part 4 Determination of the water discharge of the concrete (bleeding) Part 5 Determination of capillary absorption Part 6 infrared investigation Part 8 Determination of the solids content Part 10 Determination of water soluble chloride content Part 11 Determination of air void characteristics in hardened concrete Part 12 Determination of the alkali content of admixtures Part 13 Reference masonry mortar for testing of admixtures for masonry mortar Part 14 Determination of the corrosion behavior of steel in concrete - Electrochemical test at constant Part 15 Reference test method for testing concrete and viscosity modifying admixtures DIN EN 481 Workplace atmospheres; Determination of particle size distribution of airborne particles fo
EN 482 Workplace exposure - General requirements for the performance of procedures for the measur substances DIN EN 483 boilers for gaseous fuels - Boilers of type C with a nominal heat input not exceeding 70 kW
DIN EN 484 requirements for liquefied petroleum gas appliances - LPG powered hotplates, Including T grill for outdoor use DIN EN 485 Aluminium and aluminum alloys - Sheet, strip and plate Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Dimensional and shape tolerances for hot-rolled products Part 4 Dimensional and shape tolerances for cold-rolled products DIN EN 486 Aluminium and aluminum alloys - Extrusion ingots - Specifications DIN EN 487 Aluminium and aluminum alloys - Rolling ingots - Specifications
DIN EN 488 District heating pipes - Pre-insulated bonded pipe systems for Directly buried hot water ne assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
DIN EN 489 District heating pipes - Pre-insulated bonded pipe systems for Directly buried hot water ne steel service pipes, polyurethane thermal insulation and outer casing of polyethylene DIN EN 490 Concrete roofing tiles and fittings for roof covering and wall cladding - Product specificatio
DIN EN 491 Concrete roofing tiles and fittings for roof covering and wall cladding - Test methods DIN EN 492 Fibre-cement slates and fittings - Product specification and test methods DIN EN 494 Fibre-cement slates and fittings - Product specification and test methods DIN EN 495 sheets for waterproofing - Determination of behavior During folding at low Temperatures Part 5 Plastic and rubber sheets for roof waterproofing
DIN EN 497 requirements for liquefied petroleum gas appliances - LPG-powered multipurpose cooking outdoors
DIN EN 498 Specification for dedicated liquefied petroleum gas appliances - Barbecues for outdoor us included DIN EN 500 Mobile road construction machinery - Safety Part 1 Common requirements Part 2 Specific requirements for road milling Part 3 Specific requirements for soil-stabilizing machines and recycling machines Part 4 Specific requirements for compaction machines Part 6 Specific requirements for paver DIN EN 501 Roofing products from metal sheet - Specification for fully supported roofing products of z DIN EN 502 Roofing products from metal sheet - Specification for fully supported roofing products of s DIN EN 504 Roofing products from metal sheet - Specification for fully supported roofing products of c DIN EN 505 Roofing products from metal sheet - Specification for fully supported roofing products of s DIN EN 506 Roofing products from metal sheet - Specification for self-supporting products of copper o DIN EN 507 Roofing products from metal sheet - Specification for fully supported roofing products of a
DIN EN 508 Roofing products from metal sheet - Specification for self-supporting products of steel, alu steel sheet Part 1 steel Part 2 aluminum Part 3 Stainless Steel DIN EN 509 Decorative Gas Appliances with fuel effect DIN EN 510 Specification for protective clothing for use where there is a risk of entanglement with mo DIN EN 511 Protective gloves against cold DIN EN 512 fiber cement products - Pressure pipes and joints
DIN EN 513 profiles unplasticized polyvinyl chloride (PVC-U) for manufacture of windows and doors - D weather resistance and weather resistance to artificial weathering
DIN EN 514 profiles unplasticized polyvinyl chloride (PVC-U) for manufacture of windows and doors - D strength of welded corners and T-joints DIN EN 515 Aluminium and aluminum alloys, semi-finished products; Terms of material conditions DIN EN 516 Prefabricated accessories for roofing - Installations for roof access - Walkways, treads and DIN EN 517 Prefabricated accessories for roofing - Roof safety hooks DIN EN 520 Gypsum plasterboards - Definitions, requirements and test methods
DIN EN 521 Specification for dedicated liquefied petroleum gas appliances - Portable steam-pressure l gas appliances DIN EN 523 Steel strip sheaths for prestressing tendons - Definitions, specifications and conformity DIN EN 524 Steel strip sheaths for prestressing tendons - Test methods
Part Part Part Part Part Part
1 2 3 4 5 6
Determination Determination reverse bend Determination Determination Determination
of shape and dimensions of the bending behavior of transverse load of tensile strength of tightness (Determination of water loss)
DIN EN 525 gas-fired air heaters without heat exchangers with forced convection to heat rooms for no nominal heat input not exceeding 300 kW DIN EN 526 Inland navigation vessels; gangways to 8 m in length; Requirements, types DIN EN 527 Office furniture - desks Part 1 Dimensions Part 2 Mechanical safety requirements DIN EN 528 storage and retrieval machines - Safety requirements DIN EN 529 Respiratory protective devices - Recommendations for selection, use, care and maintenan DIN EN 530 Abrasion resistance of protective clothing material - Test methods DIN EN 534 Corrugated bitumen sheets - Product specification and test methods DIN EN 536 Road construction - Asphalt mixing plants - Safety requirements DIN EN 538 Clay roofing tiles for discontinuous laying - Test of bending resistance DIN EN 539 tiles for discontinuous laying - Determination of physical properties Part 1 examination of the waterproofing Part 2 Test for frost resistance DIN EN 541 Aluminium and aluminum alloys - Rolled products for cans, closures and lids - Specificatio DIN EN 542 Adhesives - Determination of density DIN EN 543 Adhesives - Determination of bulk density of powder and granule adhesives DIN EN 544 asphalt shingles with mineral-deposit and / or plastic insert - Product specification and tes
DIN EN 545 pipes, fittings, accessories made of ductile iron and Their joints for water pipelines - Requ methods DIN EN 546 Aluminium and aluminum alloys - Foil Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Tolerances Part 4 Special property requirements DIN EN 547 Safety of machinery - Human body measurements Part 1 Principles for deterministic mining the dimensions required for whole body access into machine Part 2 bases for the dimensions required for access openings Part 3 Anthropometric DIN EN 549 elastomer materials for seals and Diaphragms for gas appliances and gas equipment DIN EN 556 Sterilization of medical devices - Requirements for medical devices to be designated "STE Part 1 Requirements for medical devices thathave been sterilized in the final package Part 2 Requirements for aseptically processed medical devices
DIN EN 558 Industrial valves - lengths of metal valves for installation in flanged pipe systems - PN and valves
Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Tolerances Part 4 Special property requirements DIN EN 560 Gas welding equipment - Hose connections for equipment for welding, cutting and allied P DIN EN 561 Gas welding equipment - Hose couplings with shut-off valves for welding, cutting and allie DIN EN 564 Mountaineering equipment - Accessory cord - Safety requirements and test methods DIN EN 565 Mountaineering equipment - Tape - Safety requirements and test methods DIN EN 566 Mountaineering equipment - Slings - Safety requirements and test methods DIN EN 567 Mountaineering equipment - Rope clamps - Safety requirements and test methods DIN EN 568 Mountaineering equipment - Ice anchors - Safety requirements and test methods DIN EN 569 Mountaineering equipment - Pitons - Safety requirements and test methods DIN EN 570 Aluminium and aluminum alloys - slugs made to the extrusion of semi-finished products DIN EN 571 Non-destructive testing - Penetrant Part 1 General principles DIN EN 573 Aluminium and aluminum alloys - Chemical composition and form of wrought products Part 1 Numerical designation system Part 2 designation system with chemical symbols Part 3 Chemical composition and form of products DIN EN 574 Safety of machinery - Two-hand control devices - Functional aspects - Principles DIN EN 575 Aluminium and aluminum alloys - Master alloys produced by melting - Specifications DIN EN 576 Aluminium and aluminum alloys - unalloyed aluminum ingots - Specifications DIN EN 577 Aluminium and aluminum alloys - Liquid metal - Specifications
DIN EN 580 Plastics piping systems - Pipes of unplasticized polyvinyl chloride (PVC-U) - Test method fo DICHLOROMETHANE at a specified temperature (DCMT) DIN EN 581 Outdoor furniture - Seating and tables for camping, domestic and contract use Part 1 General safety requirements Part 2 Mechanical safety requirements and test methods for seating Part 3 Mechanical safety requirements and test methods for tables DIN EN 582 Thermal spraying; Determination of the tensile bond strength DIN EN 583 Non-destructive testing - Ultrasonic examination Part 1: General principles Part 2 Sensitivity and range adjustment Part 3 transmission technique Part 4 Examination for discontinuities perpendicular to the surface Part 5 specification and sizing of discontinuities Part 6 Runtime diffraction technique as a method for detection and sizing of discontinuities DIN EN 586 Aluminium and aluminum alloys - Forgings Part 1 Technical delivery conditions Part 2 Mechanical properties and additional property requirements Part 3 Dimensional and shape tolerances
DIN EN 588 Fibre cement pipes for drains and sewers Part 1 pipes, pipe joints and fittings for gravity lines Manholes and inspection chambers Part 2 DIN EN 589 Automotive fuels - LPG - Requirements and test methods DIN EN 590 Automotive fuels - diesel fuel - Requirements and test methods DIN EN 593 Industrial valves - Metallic flaps
DIN EN 594 Timber structures - Test methods - Racking strength and stiffness wall panels of wall elem construction
DIN EN 595 Timber structures - Test methods - Test of trusses for the determination of strength and de DIN EN 596 Timber structures - Test methods - Testing of walls in timber panel construction with soft s DIN EN 597 Furniture - Assessment of the ignitability of mattresses and upholstered bed bases Part 1 ignition source: smoldering cigarette Part 2 Ignition source: burning match Comparable gas flame
DIN EN 598 pipes, fittings, accessories made of ductile cast iron and Their joints for sewerage applicat and test methods
DIN EN 599 Durability of wood and wood-based products - Efficacy of wood preservatives as by determ tests Part 1 specification nach the category of Use Part 2 Classification and labeling DIN EN 601 Aluminium and aluminum alloys - Castings - Chemical composition of castings for use in c
DIN EN 602 Aluminium and aluminum alloys - Wrought products - Chemical composition of semi-finish production of products Intended to come into contact with foodstuffs DIN EN 603 Aluminium and aluminum alloys - Extruded or rolled forging Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Dimensional and shape tolerances DIN EN 604 Aluminium and aluminum alloys - Cast forging stock Part 1 Technical delivery conditions Part 2 Dimensional and shape tolerances DIN EN 606 barcoding - Labels for transport and handling of steel products DIN EN 607 Eaves gutters and accessories made of PVC-U - Definitions, requirements and test DIN EN 609 Agricultural and forestry machinery - Safety of log splitters Part 1 Wedge splitters Part 2 Screw splitters DIN EN 610 Tin and tin - tin ingots DIN EN 611 Tin and tin - tin alloy and pewter Part 1 tin alloys Part 2 path DIN EN 613 convection heaters for gaseous fuels DIN EN 614 Safety of machinery - Ergonomic design principles Part 1 Terminology and general principles
Part 2 Interactions between the design of machinery and work tasks DIN EN 615 fire - Extinguishing media - Requirements for dry powder (not for Dry powder fire class D) DIN EN 617 Continuous handling equipment and systems - Safety and EMC requirements for facilities bulk materials in silos, bunkers bins, and hoppers
DIN EN 618 Continuous handling equipment and systems - Safety and EMC requirements for mechani materials except fixed belt conveyors
DIN EN 619 Continuous handling equipment and systems - Safety and EMC requirements for mechani loads
DIN EN 620 Continuous handling equipment and systems - Safety and EMC requirements for fixed bel materials
DIN EN 621 gas-fired forced convection air heaters with to heat rooms for non-domestic use of nomina exceeding 300 kW, without a fan to assist transportation of combustion air and / or combustion produ DIN EN 622 Fiberboard - Requirements Part 1: General requirements Part 2 Requirements for hardboards Part 3 Requirements for medium boards Part 4 requirements for soft boards Part 5 requirements for plates nach the dry method (MDF) DIN EN 623 Advanced technical ceramics - Monolithic ceramics; General and textural properties Part 1 examination for the presence of defects by dye Part 2 Determination of density and porosity Part 3 Determination of particle size and particle size distribution (intercept method) Part 4 Determination of surface roughness Part 5 Determination of the volume fraction of phases by evaluation of micrographs
DIN EN 624 Specification for dedicated LPG appliances - Room sealed LPG space heating equipment fo vehicles and boats
DIN EN 625 gas-fired boilers - Specific requirements for the domestic hot water surgery of combinatio heat input not exceeding 70 kW DIN EN 626 Safety of machinery - Reduction of risks to health from hazardous substances Emitted by Part 1 Principles and specifications for machinery manufacturers Part 2 Methodology leading to verification procedures DIN EN 627 Specification for data logging and monitoring of lifts, escalators and moving walkways DIN EN 629 Transportable gas cylinders - 25E taper thread for connection of valves to gas cylinders Part 1 specification, December 2010 Replaced by DIN EN ISO 11363-1 DIN EN 631 Materials and articles in contact with food; Food container Part 1 Dimensions of container Part 2 Dimensions of accessories and conditions DIN EN 633 cement-bonded particle boards, definition and classification DIN EN 634 cement-bonded particle boards - Requirements Part 1: General requirements Part 2 Requirements for Portland cement (PC) bonded particle boards for use in dry, humid and exterio DIN EN 635 Plywood - Classification by surface appearance
Part 1 General Part 2 Hardwood Part 3: Softwood Part 5 methods of measurement and specification of the characteristics and error DIN EN 636 Plywood - Specifications
DIN EN 637 Plastics piping systems - Glass-reinforced plastics components - Determination of the leve using the gravimetric method DIN EN 639 General requirements for pressure pipes, concrete, Including joints and fittings
DIN EN 640 reinforced concrete pressure pipes and concrete pressure pipes with distributed reinforcem jacket), Including joints and fittings DIN EN 641 reinforced concrete pressure pipes with metal jacket, Including joints and fittings
DIN EN 642 prestressed concrete pressure pipes, with and without metal jacket, Including joints, fittin requirements for prestressing steel for pipes DIN EN 643 Paper and board - European list of standard grades of recovered paper and board DIN EN 645 Paper and board Intended to come into contact with food; Preparation of a cold water extr
DIN EN 646 Paper and board Intended to come into contact with foodstuffs - Determination of color fa and board DIN EN 647 Paper and board Intended to come into contact with food; Preparation of a hot water extra
DIN EN 648 Paper and board Intended to come into contact with foodstuffs - Determination of color fa brightened paper and cardboard
DIN EN 649 Resilient floor coverings - Homogeneous and heterogeneous polyvinyl chloride floor cover
DIN EN 650 Resilient floor coverings - Polyvinyl chloride floor coverings on jute backing or polyester no woven polyester with polyvinyl chloride backing - Specification DIN EN 651 Resilient floor coverings - Polyvinyl chloride floor coverings with foam layer - Specification DIN EN 652 Resilient floor coverings - Polyvinyl chloride floor coverings with cork-based backing - Spe
DIN EN 655 Resilient floor coverings - Tiles of agglomerated composition cork with polyvinyl chloride w Specification DIN EN 656 for gas boiler - boiler type B with a rated thermal input exceeding 70 kW but less than 300 DIN EN 657 Thermal spraying - Concepts and Classification DIN EN 659 Protective gloves for firefighters DIN EN 660 Resilient floor coverings - Determination of wear resistance Part 1 Stuttgart test Part 2 Frick-Taber test DIN EN 661 Resilient floor coverings - Determination of water spreading DIN EN 662 Resilient floor coverings - Determination of curling on exposure to moisture DIN EN 663 Resilient floor coverings - Determination of the decorative depth DIN EN 664 Resilient floor coverings - Determination of loss of volatiles DIN EN 665 Resilient floor coverings - Determination of plasticizer delivery DIN EN 666 Resilient floor coverings - Determination of gelation
DIN EN 669 Resilient floor coverings - Determination of dimensional stability of linoleum tiles Caused b humidity DIN EN 671 Fixed firefighting systems - Hose
Part 1 pant reels with semi-rigid pants Part 2 wall cabinets with flat pants Part 3 Maintenance of pants reels with semi-rigid hose reel shorts and pants with flat DIN EN 672 Resilient floor coverings - Determination of apparent density of agglomerated cork DIN EN 673 Glass in building - Determination of Wärmedurchgangskoeffzienten (U value) - Calculation DIN EN 674 Glass in building - Determination of thermal transmittance (U value) - Method using hot p DIN EN 675 Glass in building - Determination of thermal transmittance (U value) - Heat flow meter me DIN EN 676 Automatic forced draft burners for gaseous fuels
DIN EN 677 gas-fired heating boilers - Specific requirements for condensing boilers of nominal heat in kW DIN EN 678 Determination of the dry density of autoclaved aerated concrete DIN EN 679 Determination of autoclaved aerated concrete compressive strength of DIN EN 680 Determination of shrinkage of autoclaved aerated concrete DIN EN 681 Elastomeric seals - Material requirements for pipe joint seals used in water supply and dra Part 1 Vulcanized rubber Part 2 Thermoplastic Elastomers Part 3 Cellular materials of vulcanized rubber Part 4 Seals made of cast polyurethane
DIN EN 682 Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas hydrocarbons DIN EN 683 Aluminium and aluminum alloys - material for heat exchanger (fin stock) Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Dimensional and shape tolerances DIN EN 684 Resilient floor coverings - Determination of seam strength DIN EN 686 Resilient floor coverings - Specification for Linoleum with and without a foam backing DIN EN 687 Resilient floor coverings - Specification for linoleum and corkment backing DIN EN 688 Resilient floor coverings - Specification for Corklinoleum EN 689 Workplace atmospheres - Guidance for the assessment of exposure by inhalation to chemical comparison with limit values ??and measurement DIN EN 690 Agriculture - Manure spreaders - Safety DIN EN 691 Safety of woodworking machines Part 1 Common requirements DIN EN 692 Machine tools - Mechanical presses - Safety DIN EN 693 Machine tools - Safety - Hydraulic presses DIN EN 694 Fire Hoses - Rigid hoses for fixed systems DIN EN 695 Kitchen sinks - Connecting dimensions
DIN EN 702 Protective clothing - Protection against heat and flame - Test method: Determination of co transmission through protective clothing or its materials DIN EN 703 Agricultural machinery - loading, mixing and / or chopping and distributing silage - Securi
DIN EN 705 Plastics piping systems - Pipes and fittings made of glass-reinforced thermosetting plastic regression analysis and its application
DIN EN 706 Agricultural machinery - Vine shoot tipping - Security DIN EN 707 Agricultural machinery - Slurry tankers - Safety
DIN EN 709 machinery for agriculture and forestry - Pedestrian controlled tractors with mounted rotar driving wheel hoes - Security DIN EN 710 Safety of machinery - Safety requirements for foundry molding machines and equipment associated equipment DIN EN 711 Inland navigation vessels - Railings for decks - Requirements, types
DIN EN 712 Thermoplastics piping systems, high tensile mechanical connections between pressure pi method for the resistance to pull-out under constant load
DIN EN 713 Plastics piping systems; Mechanical joints between fittings and pressure pipes from polyo for tightness under internal pressure and bending
DIN EN 714 piping systems made of thermo plastics - Non-locked joints with Elastomeric seals betwee fittings - Test methods for leak under internal hydrostatic pressure without end thrust
DIN EN 715 piping systems made ??of thermo plastics; Tension connections between pressure pipes a Diameters; Methods of test for tightness under internal pressure using water and axial load DIN EN 716 Furniture - Children's cots and folding cots for domestic use Part 1 Safety requirements Test methods Part 2 EN 717 Wood-based panels - Determination of formaldehyde release Part 1 Formaldehyde emission by the chamber method Part 2 Formaldehyde release by the gas analysis method Part 3 Formaldehyde release by the flask method
DIN EN 718 Resilient floor coverings - Determination of mass per unit of gain or back of floor covering chloride DIN EN 720 Transportable gas cylinders - Gases and gas Mixtures Part 1 Properties of Single-gases DIN EN 721 Leisure accommodation vehicles - Requirements for safety ventilation DIN EN 722 Leisure accommodation vehicles - fueled with liquid fuel heating systems Part 1 caravans and mobile homes
DIN EN 723 Copper and copper alloys - Determination of carbon content on the inner surface of coppe burning DIN EN 725 Advanced technical ceramics - Methods of test for ceramic powders Part 1 Determination of Impurities in alumina powder Part 2 Determination of Impurities in barium titanate Part 3 Determination of the oxygen content in non-oxide powders by hot carrier gas extraction Part 4 Determination of the oxygen content in aluminum nitride by X-ray fluorescence analysis (XRF) Part 5 Determination of particle size distribution Part 8 Determination of tapped bulk density Part 9 Determination of bulk density Part 10 Determination of compression properties Part 11 Determination of compression behavior in natural sintering Part 12 Chemical analysis of zirconia DIN EN 726 Identification card systems - Requirements for smart cards and terminals for telecommun
Part Part Part Part Part Part Part
1 2 3 4 5 6 7
System Overview security framework application-independent requirements on the map application-independent, cards relevant requirements for terminal equipment payment methods Features security module
DIN EN 727 Plastics piping and ducting systems - Pipes and fittings made of thermoplastic - Determina softening temperature (VST)
DIN EN 728 Plastics piping and ducting systems - Pipes and fittings made of polyolefin - Determination induction time DIN EN 730 Gas welding equipment - Safety devices Part 1 With integrated flame arrestor Part 2 Without integrated flame DIN EN 732 Specification for dedicated liquefied petroleum gas appliances - Absorption refrigerators
DIN EN 733 centrifugal pumps with axial inlet PN 10 with bearing bracket - Nominal power, main dime system DIN EN 734 side channel pumps PN 40 - Nominal power, main dimensions, designation system DIN EN 735 connection dimensions for centrifugal pumps - Tolerances DIN EN 736 Fittings - Terminology Part 1 Definition of basic designs Part 2 Definition of the fitting parts Part 3 Definition of terms
DIN EN 741 Continuous handling equipment and systems - Safety requirements for systems and comp pneumatic conveying of Their bulk materials
DIN EN 744 Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to the method DIN EN 746 Industrial thermo-processing equipment Part 1: General safety requirements for industrial thermo-processing equipment Part 2 security requirements for combustion and fuel handling systems Part 3 Safety requirements for the generation and use of atmosphere gases Part 4 Particular safety requirements for hot dip galvanizing Part 5 Particular safety requirements for salt bath heat treatment equipment and systems Part 6 Particular safety requirements for equipment the liquid phase treatment (draft) Part 7 Particular safety requirements for vacuum thermo-processing equipment (Draft) Part 8 Particular safety requirements for quenching DIN EN 747 Furniture - Bunk beds and loft beds Part 1 requirements for safety, strength and durability Test methods Part 2 DIN EN 748 Playing field equipment - Football goals - Functional and safety requirements, test method DIN EN 749 Playing field equipment - Handball goals - Functional and safety requirements, test metho DIN EN 750 Playing field equipment - Hockey goals - Functional and safety requirements, test method
DIN EN 751 Sealing materials for metallic threaded joints in contact with gases of the 1st, 2nd and 3rd water Part 1 Anaerobic sealant Part 2 non-hardening sealant Part 3-sintered PTFE tapes DIN EN 752 drainage systems outside buildings DIN EN 754 Aluminium and aluminum alloys - bar and tube Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Round bars, tolerances on shape and dimensions Part 4 Square bars, tolerances on shape and dimensions Part 5 Rectangular bars, tolerances on shape and dimensions Part 6 Hexagonal bars, tolerances on shape and dimensions Part 7 Seamless tubes, tolerances on shape and dimensions Part 8 Porthole tool tubes, tolerances on shape and dimensions DIN EN 755 Aluminium and aluminum alloys - Extruded bars, tubes and profiles Part 1 Technical delivery conditions Part 2 Mechanical properties Part 3 Round bars, tolerances on shape and dimensions Part 4 Square bars, tolerances on shape and dimensions Part 5 Rectangular bars, tolerances on shape and dimensions Part 6 Hexagonal bars, tolerances on shape and dimensions Part 7 Seamless tubes, tolerances on shape and dimensions Part 8 Porthole tool tubes, tolerances on shape and dimensions Part 9 profiles, Dimensional and shape tolerances
DIN EN 761 Plastics piping systems - Glass-reinforced thermosetting plastics pipes (GRP) pipes - Deter creep in the dry state DIN EN 764 Pressure Equipment Part 1 Terminology - pressure, temperature, volume, nominal diameter Part 2 sizes, symbols and units Part 3 Definition of the parties Part 4 Preparation of technical delivery conditions for metallic materials Part 5 Certificates for metallic materials and compliance with the material specification Part 7 Safety systems for unfired pressure equipment DIN DIN DIN DIN DIN DIN DIN
EN EN EN EN EN EN EN
765 766 767 768 769 770 771
Sacks for the transport of food for Sacks for the transport of food for Sacks for the transport of food for Sacks for the transport of food for Sacks for the transport of food for Sacks for the transport of food for Specification for masonry units
the the the the the the
food food food food food food
aid aid aid aid aid aid
-
Sacks made Sacks made Sacks made Sacks made Sacks made Paper sacks
Polyolefingeweben other tha of jute of jute / polyolefin blends of cotton fabric with inner ba of cotton / polyolefin blends
Part 1 brickwall Part 2 calcareous sandstone Concrete masonry units Part 3 (Dense and light-weight aggregates) Aerated concrete blocks Part 4 Part 5 cast stone Part 6 natural stones DIN EN 772 Methods of test for masonry units Part 1 Determination of compressive strength Part 2 Determination of the percentage hole proportion of bricks (using paper impression)
Part 3 Determination of net volume and percentage share of perforated bricks by hydrostatic weighing (Unterwasserwägung) Part 4 stone Part 5 Part 6 Part 7
Determination of the density and the bulk density and total porosity and the open porosity of b
Determination of the active soluble salts of bricks Determination of flexural strength of concrete masonry Determination of water absorption of bricks for Feuchteisolierschichten by storage in boiling wa
Part 9 Determination of the hole and net volume and the percentage hole proportion of sand-lime bric sand filling Part 10 Determination of moisture content of calcium silicate and autoclaved aerated concrete mason
Part 11 Determination of capillary absorption of concrete masonry, aerated concrete, manufactured st stone as well as the initial water absorption of bricks Part 13 Determination of net and gross dry density of masonry units (except for natural stone) Part 14 Determination of moisture induced deformation of concrete masonry and concrete blocks Part 15 Determination of water vapor permeability of aerated concrete blocks Part 16 Determination of dimensions Part 18 Determination of frost resistance of sand-lime bricks Part 19 Determination of moisture expansion of large horizontally perforated bricks Part 20 Determination of flatness of bricks Part 21 Determination of cold water absorption of bricks and sand-lime bricks
DIN EN 774 Garden equipment - Portable powered hedge trimmers - Safety, January 2010 Replaced by DIN EN 777 radiant tube heater systems for multi-burner commercial and industrial applications Part 1 System D - Safety Part 2 System E - Safety Part 3 System F - Safety Part 4 System H - Safety
DIN EN 778 gas-fired forced convection air heaters with to heat rooms for domestic use with a nomina exceeding 70 kW, without a fan to assist transportation of combustion air and / or combustion produc DIN EN 779 Particulate air filters for general ventilation - Determination of the filtration performance
DIN EN 786 Garden equipment - Electrically powered hand-held and hand-held lawn trimmers and law Mechanical safety DIN EN 787 Sacks for the transport of food for the food aid - bags of polyethylene movie
DIN EN 788 Sacks for the transport of food for the food aid - Tubular bag-pack of laminated movie DIN EN 789 Timber structures - Test methods - Determination of mechanical properties of wood-based DIN EN 790 Inland navigation vessels - Stairs with inclination angles of 45 ° to 60 ° - Requirements, ty DIN EN 791 Drilling equipment - safety DIN EN 792 Hand-held non-electric power tools - Safety requirements Part 13 tackers DIN EN 794 Lung ventilators Part 3 Particular requirements for emergency and transport ventilators DIN EN 795 Personal fall protection equipment - Anchor devices
DIN EN 802 Plastics piping and ducting systems - injection molded thermoplastic plastics fittings for p systems - Test method for maximum deformation by crushing
DIN EN 803 Plastics piping systems - injection molded thermoplastic plastics fittings for plug socket jo piping - Test method for resistance to short-term internal pressure without end thrust
DIN EN 804 Plastics piping systems - Injection-molded pieces with Klebmuffenverbindungen for pressu Test method for resistance to hydrostatic short-term internal pressure DIN EN 805 Water supply - Requirements for water supply systems and components outside buildings DIN EN 806 Technical rules for drinking water installations (TRWI) Part 1 General Part 2 Planning Part 3 Calculation of the internal pipe diameter - Simplified procedure Part 4 installation Part 5 Operation and Maintenance DIN EN 809 Pumps and pump units for liquids - Common safety requirements DIN EN 818 Short link chain for lifting purposes round - Safety Part 1 General conditions of acceptance Part 2 medium tolerance chain for chain slings - Grade 8 Part 3 Medium tolerance chain for chain slings - Grade 4 Part 4 chain slings - Grade 8 Part 5 chain slings - Grade 4 Part 6 Chain slings - Specification for information for use and maintenance to be provided by the man Part 7 Fine tolerance hoist chain, Grade T (Types T, DAT and DT) DIN EN 821 Advanced technical ceramics - Monolithic ceramics - Thermophysical properties Part 1 Determination of thermal change in length Part 2 Measurement of thermal diffusivity by the laser flash (or Wärmepuls-) method Part 3 Determination of the specific heat capacity DIN EN 822 Thermal insulating products for building applications - Determination of length and width DIN EN 823 Thermal insulating products for building applications - Determination of thickness DIN EN 824 Thermal insulating products for building applications - Determination of squareness DIN EN 825 Thermal insulating products for building applications - Determination of flatness DIN EN 826 Thermal insulating products for building applications - Determination of compression beha DIN EN 827 Adhesives - Determination of the solids content by appointment and to constant mass
DIN EN 828 Adhesives - Wettability - Determination by measurement of contact angle and surface free Surfaces
DIN EN 832 Thermal performance of buildings - Calculation of energy requirements for heating - Resid 2003 Replaced by DIN EN 832, DIN EN ISO 13790, DIN EN ISO 13790
DIN EN 834 Heat cost allocators for the consumption value acquisition of room heating radiators - App electrical energy supply
DIN EN 835 Heat cost allocators for the consumption value acquisition of room heating radiators - App electrical energy supply by Means of evaporation DIN EN 836 Garden equipment - Powered lawnmowers - Safety DIN EN 837 Pressure gauges Part 1 Pressure gauges with Bourdon tubes; Dimensions, metrology, requirements and testing Part 2 Selection and installation Recommendations for pressure gauges Part 3 Pressure gauges with capsule plate and springs; Dimensions, metrology, requirements and test
DIN EN 838 Workplace exposure - measurement of gases and vapors using diffusive samplers - Requir methods EN 840 Mobile waste bins Part 1 container with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and de
Part 2 Containers with 4 wheels with a capacity up to 1300 l with flat lid (s), for trunnion and / or comb Dimensions and design
Part 3 Containers with 4 wheels with a capacity up to 1300 l with dome lid (s), for trunnion and / or co Dimensions and design
Part 4 Containers with 4 wheels with a capacity up to 1700 l with flat lid (s), for wide trunnion or BG an lifting devices - Dimensions and design Part 5 Performance requirements and test methods Part 6 health and safety requirements DIN EN 841 bar coding - Symbology, description of formats DIN EN 842 Safety of machinery - Visual danger signals - General requirements, design and testing DIN EN 843 Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temp Part 1 Determination of flexural strength Part 2 Determination of flexural modulus, shear modulus and Poisson's ratio Part 3 Determination of the parameters of subcritical crack growth from bending strength tests at con Part 4 Vickers hardness test, Knoop and Rockwell Part 5 Statistical analysis Part 6 Guideline for fractographic investigation Part 7 C-ring tests Part 8 Guidelines for Conducting overload tests DIN EN 844 Round and sawn timber - Terminology Part 1 General terms common to round timber and sawn timber Part 2 General terms Relating to round timber Part 3 General terms Relating to sawn timber Part 4 Terms Relating to moisture content Part 5 Terms Relating to dimensions of round timber Part 6 Terms Relating to dimensions of sawn timber
Part 7 Terms Relating to anatomical structure of timber Part 8 Terms Relating to features of round timber Part 9 Terms Relating to features of sawn timber Part 10 Terms Relating to stain and fungal attack Part 11 criteria to insect attack Part 12 Additional terms and general index DIN EN 845 Specification for ancillary components for masonry Part 1 Wall ties, tension straps, hangers and brackets Part 2 if Part 3 bed joint reinforcement steel DIN EN 846 Methods of test for ancillary components for masonry Part 2 Determination of bond strength of prefabricated bed joint reinforcement Part 3 Determination of shear strength of the welds in prefabricated bed joint reinforcement Part 4 Determination of strength and load-deformation characteristics of tapes Part 5 Determination of tensile and compressive load capacity and stiffness of wall ties (couplet test) Part 6 Determination of tensile and compressive load capacity and stiffness of wall ties (one-sided tes Part 7 Determination of shear strength and stiffness of masonry connectors (couplet test in mortar joi Part 8 Determination of bearing capacity and the load-deformation characteristics of Balkenauflagern Part 9 Determination of flexural and shear resistance of falls Part 10 Determination of bearing capacity and the load-deformation characteristics of consoles Part 11 Determination of dimensions and the elevation of falls Part 13 Determination of impact resistance, abrasion resistance and corrosion resistance of organic co
Part 14 Determination of initial shear strength of the bond between the prefabricated part of a Partiall supplemented fall and the masonry located above the lintel DIN EN 847 Tools for woodworking - Safety requirements Part 1 milling and planing tools, circular saw blades Part 2 Requirements for the shank milling cutters Part 3 grips DIN EN 848 Safety of woodworking machines - One side molding machines with rotating tool Part 1 vertical spindle molding machines Part 2 Single spindle hand fed / integrated Part 3 NC drilling and milling machines DIN EN 851 Aluminium and aluminum alloys - Circle and circle for the manufacture of kitchen ware - S DIN EN 853 Rubber hoses and hose assemblies - Hydraulic hoses with wire mesh liner - Specification DIN EN 854 Rubber hoses and hose assemblies - Hydraulic hoses with textile insert - Specification DIN EN 855 plastics hoses and hose assemblies - plastic hydraulic hoses with textile insert - Specificat DIN EN 856 Rubber hoses and hose assemblies - Hydraulic hoses with wire spiral inlay - Specification DIN EN 857 Rubber hoses and hose assemblies - Compact hydraulic hoses with wire mesh liner - Spec DIN EN 858 Separator systems for light liquids (eg. As oil and gasoline) Part 1 of design, performance and testing, marking and quality control Part 2 Selection of nominal size, installation, operation and maintenance
DIN EN 859 Safety of woodworking machines - Hand fed surface planing DIN EN 860 Safety of woodworking machines - One side molding machines thickness planers DIN EN 861 Safety of woodworking machines - Surface planing and thicknessing machines
DIN EN 862 Packaging - Child-resistant packaging - Requirements and test methods for non-reclosable pharmaceutical products DIN EN 863 Protective clothing - Mechanical properties - Test method: Puncture resistance DIN EN 867 Non-biological systems for use in sterilizers
Part 5 Specification for indicator systems and test pieces for performance testing for small sterilizers T DIN EN 868 for terminally sterilized medical packaging devices Part 2 Sterilization wrap - Requirements and test methods
Part 3 paper for making paper bags (specified in EN 868-4) and for the production of pouches and ree 868-5) - Requirements and test methods Part 4 Paper bags - Requirements and test methods Part 5-sealable pouches and reels of porous materials and plastic film-construction - Requirements an Part 6 paper for low temperature sterilization Processes - Requirements and test methods Part 7 Adhesive coated paper for low temperature sterilization Processes - Requirements and test met Part 8 Reusable sterilization containers for steam sterilizers nach EN 285 - Requirements and test met Uncoated nonwoven materials Part 9 of polyolefin - Requirements and test methods Adhesive coated nonwoven materials Part 10 of polyolefin - Requirements and test methods DIN EN 869 Safety of machinery - Safety requirements for pressure metal diecasting DIN EN 872 Water quality - Determination of suspended solids - Method by filtration through glass fibe
DIN EN 877 pipes and fittings made of cast iron, Their joints and accessories for the dewatering of bui Requirements, test methods and quality assurance DIN EN 878 Chemicals used for treatment of water Intended for human consumption - Aluminium sulf
DIN EN 881 Chemicals used for treatment of water Intended for human consumption - Aluminium chlo aluminum hydroxide (monomeric) and Aluminiumhydroxidchloridsulfat (monomeric) DIN EN 882 Chemicals used for treatment of water Intended for human consumption - Sodium alumin
DIN EN 883 Chemicals used for treatment of water Intended for human consumption - Polyaluminiumc Polyaluminiumchloridhydroxidsulfat
DIN EN 885 Chemicals used for treatment of water Intended for human consumption - Polyaluminiumh
DIN EN 886 Chemicals used for treatment of water Intended for human consumption - Polyaluminiumh Aluminum sulfate, iron (III) - DIN EN 887 Chemicals used for treatment of water Intended for human co DIN EN 888 Chemicals used for treatment of water Intended for human consumption - Iron (III) chlorid DIN EN 889 Chemicals used for treatment of water Intended for human consumption - Iron (II) sulfate DIN EN 890 Chemicals used for treatment of water Intended for human consumption - Iron (III) sulpha Chloride-sulphate of iron (III) - DIN EN 891 Chemicals used for treatment of water Intended for human DIN EN 892 Mountaineering equipment - Dynamic mountaineering ropes - Safety requirements and te DIN EN 893 Mountaineering equipment - Crampons - Safety requirements and test methods DIN EN 894 Safety of machinery - Ergonomics requirements for the design of displays and control actu Part 1: General principles for human interactions with displays and control actuators
Part 2 ads Part 3 actuators Part 4 Location and arrangement of displays and control actuators DIN EN 896 Chemicals used for treatment of water Intended for human DIN EN 897 Chemicals used for treatment of water Intended for human DIN EN 898 Chemicals used for treatment of water Intended for human DIN EN 899 Chemicals used for treatment of water Intended for human DIN EN 900 Chemicals used for treatment of water Intended for human DIN EN 901 Chemicals used for treatment of water Intended for human DIN EN 902 Chemicals used for treatment of water Intended for human
consumption consumption consumption consumption consumption consumption consumption
-
Sodium hydrox Sodium carbon Sodium Sulfuric acid Calcium hypoch Sodium hypoch Hydrogen perox
DIN EN 903 Water quality; Determination of Anionic Surfactants by measuring the methylene blue ind 1: 1984, modified) DIN EN 908 Agricultural and forestry machinery - Irrigation Machines with hose reel - Security DIN EN 909 Agricultural and forestry machinery - Centre pivot and moving lateral irrigation machines DIN EN 911 Plastics piping systems - Relationship with Elastomeric seals and mechanical connections thermoplastic materials - Methods of test for tightness under external hydrostatic pressure DIN EN 912 Timber fasteners - Specifications for dowels Particular type of wood DIN EN 913 Gymnastic equipment - General safety requirements and test methods
DIN EN 914 Gymnastic equipment - Ingots and combined uneven bars / ingots - Requirements and tes safety DIN EN 915 Gymnastic equipment - Uneven Bars - Requirements and test methods Including safety DIN EN 916 Gymnastic equipment - Vaulting boxes - Requirements and test methods Including safety
DIN EN 917 Plastics piping systems - Thermoplastics fittings - Test method for resistance to internal pr
DIN EN 920 Paper and board Intended to come into contact with foodstuffs - Determination of dry mat Aqueous extract of DIN EN 923 Adhesives - Terms and definitions DIN EN 924 Adhesives - Solvent-based and solvent-free adhesives - Determination of flash point DIN EN 926 equipment for paragliding - paragliders Part 1 Requirements and test methods for structural strength Part 2 Requirements and test methods for classifying flight safety characteristics DIN EN 927 and varnishes - Coating materials and coating systems for exterior wood Part 1 Classification and selection Part 2 Performance requirements Part 3 outdoor exposure Part 5 Assessment of water permeability Part 6 Artificial weathering of wood coatings with fluorescent UV lamps and water DIN EN 929 Inland navigation vessels; Pushed convoys; Pole mount for Detachable signal masts
DIN EN 930 machines for the manufacture of footwear, leather and imitation leather goods - Roughing and trimming machines - Safety requirements DIN EN 931 machines for the production of shoes - Lasting machines - Safety requirements DIN EN 932 Tests for general properties of aggregates
Part 1 sampling procedure Part 2 methods for reducing laboratory samples Part 3 Procedure and terminology for simplified petrographic description Part 5 Common equipment and calibration Part 6 definitions for the repeatability and reproducibility DIN EN 933 Tests for geometrical properties of aggregates Part 1 Determination of particle size distribution - Sieving Part 2 Determination of particle size distribution, test sieves, nominal size of Aperture Part 3 Determination of particle shape - flakiness Part 4 Determination of particle shape - shape index Part 5 Determination of percentage of crushed and broken into coarse aggregate particles Surfaces Part 6 flow coefficient of aggregates Part 7 Determination of shell content; percentage of shells in coarse aggregates Part 8 Assessment of fines - Sand equivalent test Part 9 Assessment of fines - Methylene blue test Part 10 Assessment of fines - Grading of fillers (air jet sieving) Part 11 division of the Constituents of coarse recycled aggregate DIN EN 934 Admixtures for concrete, mortar and grout Part 1 Common requirements Part 2 Concrete admixtures - Definitions, requirements, conformity, marking and labeling Part 3 Admixtures for masonry mortar - Definitions, requirements, conformity, marking and labeling Part 4 Additives for prestressing tendons Grout for - Definitions, requirements, conformity, marking an Part 5 Admixtures for sprayed concrete - Definitions, requirements, conformity, marking and labeling Part 6 Sampling, conformity control and evaluation of conformity
DIN EN 935 Chemicals used for treatment of water Intended for human consumption - Aluminium iron (monomeric) and aluminum-iron (III) hydroxidchlorid (monomeric) DIN EN 936 Chemicals used for treatment of water Intended for human consumption - carbon dioxide DIN EN 937 Chemicals used for treatment of water Intended for human consumption - Chlorine DIN EN 938 Chemicals used for treatment of water Intended for human consumption - Sodium chlorite DIN EN 939 Chemicals used for treatment of water Intended for human consumption - hydrochloric ac DIN EN 940 Safety of woodworking machines - woodworking machinery DIN EN 941 Aluminium and aluminum alloys - Circle and circle for general applications - Specifications DIN EN 942 Timber in joinery - General requirements DIN EN 943 Protective clothing against liquid and gaseous chemicals, aerosols and solid particles Inclu
Part 1 Performance requirements for ventilated and non-ventilated 'gas-tight' (Type 1) and 'non-gas-tig chemical protective suits Part 2 Performance requirements for gas-tight (Type 1) chemical protective suits for emergency teams DIN EN 947 swing doors - Determination of the resistance to vertical load DIN EN 948 swing doors - Determination of the resistance to static torsion
DIN EN 949 windows, doors, turning and blinds, curtain walling - Determination of the resistance of do with a soft and heavy impactor DIN EN 950 door panels - Determination of the resistance to hard thrust
DIN EN 951 Door leaves - Measurement procedure for the determination of the height, width, thicknes DIN EN 952 Door leaves - General and local flatness - Measurement
DIN EN 953 Safety of machinery - Guards - General requirements for the design and construction of fix guards as DIN EN 957 Stationary training equipment Part 1 General safety requirements and test methods Part 2 Strength training equipment, additional specific safety requirements and test methods Part 4 Strength workout benches, additional specific safety requirements and test methods
Part 5 Stationary exercise bicycles and crank training equipment for the upper body, additional specifi requirements and test methods Part 6 Treadmills, additional specific safety requirements and test methods Part 7 Rowing machines, additional specific safety requirements and test methods Part 8 stepper, stair climbing and climbers - Additional specific safety requirements and test methods Part 9 Elliptical trainers, additional specific safety requirements and test methods
Part 10 Training bicycles with a fixed wheel or without freewheel, additional specific safety requiremen
DIN EN 958 Mountaineering equipment - Energy absorbing systems for use in climbing climbing - Safe test methods DIN EN 959 Mountaineering equipment - Rock anchors - Safety requirements and test methods DIN EN 960 probes for testing of protective helmets DIN EN 966 airborne sports
DIN EN 969 pipes, fittings, accessories and Their joints for ductile cast iron gas pipelines - Requiremen DIN EN 972 Tannery machines - rolling machines - Safety requirements
DIN EN 973 Chemicals used for treatment of water Intended for human consumption - Sodium chlorid ion exchangers DIN EN 974 Chemicals used for treatment of water Intended for human consumption - Phosphoric acid DIN EN 975 timber - Appearance grading of hardwood Part 1 oak and beech Part 2 Poplar DIN EN 976 Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the of liquid petroleum based fuels Part 1 Requirements and test methods for single wall tanks Part 2 transportation, handling, storage and installation of single-walled tanks DIN DIN DIN DIN DIN
EN EN EN EN EN
977 978 981 984 985
Underground tanks of glass-reinforced plastics (GRP) pipes - Test arrangement for one-sid Underground tanks of glass-reinforced plastics (GRP) pipes - Determination of the factor ? Safety of machinery - System of auditory and visual danger and information signals Textile floor coverings - Determination of Nutzschichtgewichts needled floor coverings Textile floor coverings - Castor chair test
DIN EN 986 Textile floor coverings - Tiles - Determination of dimensional change due to the effects of and temperature conditions and vertical surface deformation
DIN EN 988 Zinc and zinc alloys - Specifications for rolled flat products for the construction industry
DIN EN 989 Determination of the bond behavior between reinforcing bar and autoclaved aerated conc Ausdrückprüfung
DIN EN 990 test methods for verification of corrosion protection of reinforcement in autoclaved aerate lightweight aggregate concrete
DIN EN 991 Determination of dimensions of prefabricated reinforced components of autoclaved aerate lightweight aggregate concrete DIN EN 992 Determination of the dry density of lightweight aggregate concrete DIN EN 993 Methods of test for dense shaped refractory products Part 1 Determination of bulk density, apparent porosity and total porosity Part 2 Determination of density Part 3 tests for carbon-Containing products Part 4 Determination of gas permeability Part 5 Determination of cold crushing strength Part 6 Determination of flexural strength at room temperature Part 7 Determination of flexural strength at elevated Temperatures Part 9 Determination of the pressure flow behavior Part 10 Determination of permanent change in dimensions on heating Part 11 Determination of thermal resistance Part 12 Determination of the cone equivalent (refractoriness) Part 13 requirements for reference cones for laboratory use Part 15 Determination of thermal conductivity by the hot-wire (parallel) method Part 16 Determination of resistance to sulfuric acid Part 17 Determination of bulk density of granular materials by the mercury displacement method und Part 18 Determination of bulk density of granular materials by the water displacement method under Part 19 Determination of thermal expansion by a differential method DIN EN 995 Textile floor coverings - Determination of the deformability of backings ("cold flow") DIN EN 996 Piling equipment - Safety requirements DIN EN 997 WC pans with integral trap DIN EN 998 Specification for mortar for masonry Part 1 plaster Part 2 mortar DIN EN 1000-1999 [ Edit ] DIN EN 1001 Durability of wood and wood products - Terminology Part 1 List of equivalent terms Vocabulary Part 2
DIN EN 1004 Rolling towers made of prefabricated elements - Materials, dimensions, design loads and DIN EN 1005 Safety of machinery - Human physical performance Part 1 Definitions Part 2 Manual handling of in connection with machines and machine parts
Part 3 Recommended force limits for machinery surgery Part 4 Evaluation of working postures and movements in relation to machinery Part 5 risk assessment for short-cycle handling at high frequencies
DIN EN 1006 Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of sampl assessment of properties DIN EN 1007 Advanced technical ceramics - Ceramic composites; Method for testing the fiber reinforc Part 1 Determination of size content Part 2 Determination of fineness Part 3 Determination of fiber diameter and -querschnitts Part 4 Determination of tensile properties of fibers at room temperature
Part 5 Determination of distribution of tensile strength and elongation of fibers in the fiber bundle at r Part 6 Determination of tensile properties of filaments at high temperature Part 7 Determination of distribution of tensile strength and elongation of fibers in the fiber bundle at h
DIN EN 1008 Mixing water for concrete - Specification for sampling, testing and assesing the suitabilit water accumulating in concrete production, as mixing water for concrete
DIN EN 1010 Safety of machinery - Safety requirements for the design and construction of printing an machines Part 1 Common requirements Part 2 Printing and varnishing machines Including pre-press Part 3 Cutting Machines Part 4 Bookbinding, paper converting and finishing machines Part 5 Wellpappenerzeugungs-, flat and corrugated board processing machines With EN 1011 Welding - Recommendations for welding of metallic materials Part 1 General guidance for arc welding Part 2 of ferritic steels arc welding Part 3 arc welding of stainless steels Part 4 arc welding of aluminum and Alumiumlegierungen Part 5 welding of clad steels Part 6 laser welding Part 7 of electron beam welding Part 8 welding of cast iron DIN EN 1012 compressors and vacuum pumps - Safety requirements Part 1 Compressors Part 2 Vacuum Pumps
DIN EN 1013 Light Transmitting profiled plastic sheeting for single interior and exterior applications on ceilings - Requirements and test methods DIN EN 1014 Wood preservatives - creosote (creosote) and creosoted timber - Sampling and analysis Part 1 Procedure for sampling creosote Part 2 for a sample of creosote from creosoted timber for subsequent offer analysis Part 3 Determination of benzo [ a ] pyrene in creosote Part 4 Determination of water-extractable phenols in the creosote
DIN EN 1015 Methods of test for mortar for masonry Part 1 Determination of particle size distribution (by sieve analysis) Part 2 sampling of mortars and preparation of test Part 3 Determination of consistence of fresh mortar (by flow table) Part 4 Determination of consistence of fresh mortar (by Eindringgerät) Part 6 Determination of bulk density of fresh mortar Part 7 Determination of air content of fresh mortar Part 9 Determination of workable life and correction of fresh mortar Part 10 Determination of dry bulk of hardened mortar Part 11 Determination of flexural and compressive strength of hardened mortar Part 12 Determination of adhesive strength of hardened rendering and plastering mortars Part 17 Determination of water-soluble chlorides of fresh mortar Part 18 Determination of capillary absorption of hardened mortar (hardened mortar) Part 19 Determination of water vapor permeability of hard plaster mortars mortars from Part 21 Determination of the compatibility of deposits rendering mortars with substrate EN 1017 Chemicals used for treatment of water Intended for human consumption - calcined dolomite DIN EN 1018 Chemicals used for treatment of water Intended for human consumption - Calcium carbo DIN EN 1019 Chemicals used for treatment of water Intended for human consumption - sulfur dioxide
DIN EN 1020 gas-fired forced convection air heaters with for non-domestic use of nominal heat input n kW, Incorporating a fan to assist transportation of combustion air and / or combustion products DIN EN 1021 Furniture - Assessment of the ignitability of upholstered furniture Part 1 Ignition source smoldering cigarette Part 2 A a match Comparable gas flame ignition source DIN EN 1022 Domestic furniture - Seating - Determination of stability DIN EN 1023 Office furniture - space planning elements Part 1 Dimensions Part 2 Mechanical safety requirements Examination Part 3 DIN EN 1024 Clay roofing tiles for discontinuous laying - Determination of geometric characteristics DIN EN 1026 Windows and doors - Air permeability - Test methods DIN EN 1027 Windows and doors - Water tightness - Test methods DIN EN 1028 Fire fighting pumps - Fire-fighting centrifugal pumps with primer Part 1 Classification - General and safety requirements Part 2 Determination of conformity with the general and safety requirements
DIN EN 1032 Mechanical vibration - Testing of mobile machinery in order to deterministic mine the vib value
DIN EN 1034 Safety of machinery - Safety requirements for the design and construction of paper mak machines Part 1 Common requirements Part 2 debarking drums Part 3 rewinder slitter and Part 4 pulper and Their loading facilities
Part 5 sheeter Part 6 calender Part 7 wove paper Part 8 grinding plants Part 13 Machines for de-wiring bales and units Part 14 Reel splitter Part 16 paper and board machines Part 17 tissue machines Part 21 coater Part 22 defibrillator Part 26 roll wrapping machine Part 27 role transport system DIN EN 1035 Tannery machines - Moving platen machinery - Safety requirements DIN EN 1036 Glass in building - Mirrors from silver float glass for indoor use Part 1 Definitions, requirements and test methods Part 2 Conformity assessment - Product standard DIN EN 1037 Safety of machinery - Prevention of unexpected start
DIN EN 1038 Identification card systems - Telecommunications Applications - phones with payment fu cards DIN EN 1040 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation activity (based test) of chemical disinfectants and antiseptics - Test method and requirements (phase DIN EN 1041 Information Supplied by the manufacturer of medical devices DIN EN 1045 Brazing - flux for brazing - Classification and technical delivery DIN EN 1047 storage units - Classification and methods of test for resistance to fire Part 1 Data cabinets and diskette inserts Part 2 Data rooms and data containers
DIN EN 1048 Heat exchangers - Air cooled liquid chillers "dry cooling towers" - Test methods for Estab performance DIN EN 1049 textiles; Tissue; Construction inspection method Part 2 Determination of the number of threads per unit length DIN EN 1050 Safety of Machinery, Principles for Risk Assessment, December 2007 Replaced by DIN EN DIN EN 1052 Methods of test for masonry Part 1 Determination of compressive strength Part 2 Determination of flexural strength Part 3 Determination of the initial shear strength (adhesive shear strength) Part 4 Determination of shear strength at a moisture barrier Part 5 Determination of Biegehaftzugfestigkeit Part 10 Supplementary Provisions
DIN EN 1053 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - T watertightness DIN EN 1054 Plastics piping systems - Thermoplastics piping systems for drains for draining domestic method for gas tightness of connections
DIN EN 1055 Plastics piping systems - Thermoplastics piping systems for waste water systems inside method for resistance to elevated temperature
DIN EN 1057 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary a DIN EN 1058 Wood-based panels - Determination of characteristic 5 -% - values ??and characteristic m DIN EN 1060 Non-Invasive Blood Pressure Monitors Part 3 Supplementary requirements for electro-mechanical blood pressure measuring systems Part 4 Methods of measuring the accuracy of automated non-invasive blood pressure monitors
DIN EN 1062 Paints and varnishes - Coating materials and coating systems for mineral substrate and c Part 1 classification Part 3 Determination of water permeability Part 6 Determination of carbon dioxide diffusion rate (permeability) Part 7 Determination of crack bridging properties Part 11 Method of conditioning before testing DIN EN 1063 Glass in building - Security glazing - Testing and classification of resistance to fire DIN EN 1064 Medical computer science - Standard communication protocol - Computer-assisted electr DIN EN 1065 props steel extractor - product definition, design and assessment by calculation and test DIN EN 1067 Adhesives - Examination and preparation of samples for testing DIN EN 1068 Medical computer science - Registration of coding schemes DIN EN 1069 Water Slides Part 1 Safety requirements and test methods Part 2 Notes DIN EN 1071 Advanced technical ceramics - Methods of test for ceramic coatings Part 1 Determination of film thickness with a contact profilometer Part 2 Determination of coating thickness by the crater Part 3 Determination of adhesion and forms of mechanical failure by a scratch test Part 4 Determination of chemical composition by electron probe microanalysis (EPMA) Part 6 Determination of resistance to abrasive wear of layers by Means of micro-abrasion test Part 9 Determination of fracture strain Part 10 Determination of coating thickness by cross sectioning Part 12 vibrational weartest Part 13 Determination of wear rate by the pin-on-disk test DIN EN 1073 Protective clothing against radioactive contamination
Part 1 Requirements and test methods for ventilated protective clothing against radioactive contamin particles
Part 2 Requirements and test methods for non-ventilated protective clothing against radioactive conta particles DIN EN 1074 Valves for water supply - Fitness for purpose requirements and Appropriate verification t Part 1: General requirements Part 2 shut-off valves Part 3 backflow preventer
Part 4 ventilation valves with float Part 5 Control Valves Part 6 hydrants DIN EN 1075 Timber structures - Test methods - connections with nail plates
DIN EN 1076 Workplace exposure - Measurement of gases and vapors using pumped samplers - Requ methods DIN EN 1077 Helmets for alpine skiers and snowboarders DIN EN 1078 Helmets for pedal cyclists and for users of skateboards and roller skates DIN EN 1080 Impact protection helmets for young children DIN EN 1081 Resilient floor coverings - Determination of electrical resistance DIN EN 1082 Protective clothing - Gloves and arm guards protecting against cuts and stabs by hand k Part 1 chain mail gloves and arm guards Part 2 Gloves and arm guards made of material other than chain mail Part 3 Impact cut test for fabric, leather and other materials DIN EN 1083 Power-operated brushing tools Part 1 Definitions and Nomenclature Part 2 Safety requirements DIN EN 1085 wastewater treatment - dictionary
DIN EN 1086 Sacks for the transport of food for the food aid - Recommendations for the selection of th bag sacks with respect to the product to be packaged DIN EN 1087 Particle board - Determination of moisture resistance Part 1 Boil test DIN EN 1088 Safety of machinery - Interlocking devices associated with guards - Principles for design DIN EN 1089 Transportable gas cylinders - Gas cylinder identification (excluding liquefied petroleum g Part 3 color coding DIN EN 1090 Execution of steel structures and aluminum structures Part 1 conformity assessment of structural components Part 2 Technical rules for the Execution of steel structures Part 3 Technical rules for the execution of aluminum structures DIN EN 1091 Vacuum sewerage systems outside buildings
DIN EN 1092 Flanges and Their joints - Circular flanges for pipes referred by, valves, fittings and acces designated Part 1 steel flanges Part 2 Cast iron Copper alloy flanges Part 3 Part 4 aluminum alloy flanges DIN EN 1093 Safety of machinery - Evaluation of the emission of airborne hazardous substances Part 1 Selection of test methods Part 2 tracer gas method for measuring the emission rate of a pollutant givenName Part 3 test method for measuring the emission rate of a pollutant givenName Part 4 Capture efficiency of at exhaust system - tracer method Part 6 Separation efficiency by mass, diffuse outlet
Part 7 Separation efficiency by mass, ducted outlet Part 8 Pollutant concentration parameter substance, test method Part 9 of the pollutant concentration parameter, room method Part 11 Cleaning Index DIN EN 1094 Refractory products for insulating purposes Part 1 Terminology, classification and test methods for high temperature insulation wools Part 2 Classification of shaped products Part 4 Determination of bulk density and total porosity of shaped products Part 6 Determination of permanent change in dimensions of shaped products on heating DIN EN 1096 Glass in building - Coated glass Part 1 Definitions and classification Part 2 Requirements and test methods for coatings of classes A, B and S Part 3 Requirements and test methods for coatings of Class C and D Part 4 Evaluation of conformity / Product standard DIN EN 1097 Tests for mechanical and physical properties of aggregates Part 1 Determination of the resistance to wear (micro-Deval) Part 2 method for the determination of resistance to fragmentation Part 3 Determination of bulk density and voids Part 4 Determination of the voids of dry compacted filler Part 5 Determination of water content by oven-drying Part 6 Determination of bulk density and water absorption Part 7 Determination of bulk density of filler - pycnometer method Part 8 Determination of the polished stone value Part 9 Determination of resistance to wear from studded tires - Nordic test Part 10 Determination of Wassersaughöhe
DIN EN 1101 Textiles - Burning behavior of curtains and drapes - Detailed procedure to deterministic m of vertically oriented specimens (small flame)
DIN EN 1102 Textiles - Burning behavior of curtains and drapes - Detailed procedure to deterministic m spread properties of vertically oriented specimens DIN EN 1103 Textiles - Fabrics for apparel - Detailed procedure to deterministic mine the burning beha
DIN EN 1104 Paper and board Intended to come into contact with foodstuffs - Determination of the tra antimicrobial Constituents DIN EN 1106 Manually operated taps for gas appliances DIN EN 1107 Flexible sheets for waterproofing - Determination of dimensional stability Bitumen sheets for roof Part 1 waterproofing Part 2 plastic and rubber sheets for roof waterproofing
DIN EN 1108 Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination stability under cyclic temperature change
DIN EN 1109 Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination
DIN EN 1110 Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination at elevated temperature
DIN EN 1111 Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
DIN EN 1112 sanitary fittings - sanitary fittings for showers for water supply systems of type 1 and typ technical specification
DIN EN 1113 Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 General technical specification DIN EN 1114 Plastics and rubber machines - extruder and extrusion lines Part 1 Safety requirements for extruders Part 3 safety requirements for deductions DIN EN 1116 Kitchen Furniture - Coordination sizes for kitchen furniture and kitchen appliances DIN EN 1117 Heat exchangers - Liquid cooled condensers Refrigerant - Test methods for Establishing t DIN EN 1118 Heat exchangers - Refrigerant cooled liquid chillers - Test methods for Establishing the p
DIN EN 1119 Plastics piping systems - joints for pipes and fittings made of glass-reinforced thermosett pipes - Test method for leaks and damage resistance of non-pressure-resistant flexible joints with Elas elements
DIN EN 1120 Plastics piping systems - Pipes and fittings made of glass-reinforced thermosetting plasti Determination of the resistance to chemical action of the inside of a section in the deformed state DIN EN 1121 Doors - Behaviour between two different climates - Test methods DIN EN 1122 Plastics - Determination of cadmium - wet digestion method DIN EN 1123 Pipes and fittings of Longitudinally welded galvanized steel pipes with spigot and socket Part 1 requirements, testing, quality control Part 2 Dimensions Part 3 Dimensions and special requirements for vacuum drainage systems and for drainage systems i DIN EN 1124 Pipes and fittings of Longitudinally welded stainless steel pipes with spigot and socket fo Part 1 requirements, testing, quality control Part 2 System S - Dimensions Part 3 System X - Dimensions Part 4 components for vacuum drainage systems and drainage systems on ships
DIN EN 1125 Building hardware, panic exit devices operated by a horizontal bar, for use on escape rou and test methods DIN EN 1127 Explosive atmospheres - Explosion protection Part 1 Basic concepts and methodology Part 2 Basic concepts and methodology for mining DIN EN 1128 cement bonded particle boards - Determination of impact resistance with a hardbody DIN EN 1129 Furniture - Foldaway beds - Safety requirements and test methods Part 1 Safety requirements Test methods Part 2 DIN EN 1130 Furniture - Cribs and cradles for domestic use Part 1 Safety requirements Test methods Part 2 DIN EN 1131 Fruit and vegetable juices - Determination of the relative density DIN EN 1132 Fruit and vegetable juices - Determination of pH DIN EN 1133 Fruit and vegetable juices - Determination of the formalin
DIN EN 1134 Fruit and vegetable juices - Determination of sodium, potassium, calcium and magnesium spectrophotometry By (AAS) DIN EN 1135 Fruit and vegetable juices - Determination of ash content DIN EN 1136 Fruit and vegetable juices - Determination of phosphorus content; Spectrophotometric m
DIN EN 1137 Fruit and Vegetable Juices - Enzymatic Determination of citric acid (citrate); Spectrophoto determination of NADH
DIN EN 1138 Fruit and vegetable juices - Enzymatic determination of L-malic acid (L-malate); Spectrop determination of NADH
DIN EN 1139 Fruit and vegetable juices - Enzymatic determination of D-isocitric acid; Spectrophotome NADPH
DIN EN 1140 Fruit and vegetable juices - Enzymatic determination of levels of D-glucose and D-fructos Spectrophotometric Determination of NADPH DIN EN 1141 Fruit and vegetable juices - Spectrophotometric Determination of proline DIN EN 1142 Fruit and vegetable juices - Determination of sulphate content DIN EN 1143 storage units - Requirements, classification and methods of test for resistance to burglar Part 1 safes, safes for ATMs, strongroom doors and strong rooms Part 2 deposit system
DIN EN 1146 Respiratory protective devices - contained open-circuit compressed air with a hood for es Requirements, testing, marking DIN EN 1147 Portable ladders for fire service use
DIN EN 1148 Heat exchangers - water / water heat exchangers for district heating - Test method for Es performance DIN EN 1149 Protective clothing - Electrostatic properties Part 1 Test method for measurement of surface resistivity Part 2 Test method for measurement of the electrical resistance through a material (vertical resistance Part 3 Test methods for measurement of charge decay Part 5 performance requirements for materials and construction requirements DIN EN 1150 Protective clothing - Visibility clothing for non-professional use - Test methods and requir
DIN EN 1151 Pumps - Centrifugal Pumps - Circulation pumps having a rated power up to 200 W for he domestic hot water for domestic use Part 2 Geräuschprüfvorschrift (vibro-acoustic) for measurement of fluid-borne noise and sound DIN EN 1154 Building hardware - door closing devices with controlled closing - Requirements and test
DIN EN 1155 Building hardware - Electrically powered hold-open devices for swing doors - Requiremen DIN EN 1158 Building hardware - Door co-- Requirements and test methods DIN EN 1159 Advanced technical ceramics - Ceramic composites - Thermophysical properties Part 1 Determination of thermal expansion Part 2 Determination of thermal diffusivity Part 3 Determination of the specific heat capacity DIN EN 1160 Installation and equipment for liquefied natural gas - General characteristics of liquefied DIN EN 1161 Feather and down - Test methods - Determination of moisture content DIN EN 1162 Feather and down - Test methods - Determination of the number of oxygen DIN EN 1163 Feather and down - Test methods - Determination of oil and fat content
DIN EN 1164 Feather and down - Test methods - Determination of the turbidity of at Aqueous extract DIN EN 1165 Feather and down - Test methods - Determination of water-soluble chlorides DIN EN 1167 Feather and down - Test methods for measuring the sizes filled with feathers and / or dow DIN EN 1168 Precast concrete products - Hollow core slabs DIN EN 1169 Precast concrete products - General rules for factory production control of glass fiber rein DIN EN 1170 Precast concrete products - Test method for glass fiber reinforced concrete Part 1 deterministic mining the consistency of the matrix; Setting test Part 2 Determination of the fiber content in fresh GFB; washout Part 3 Determination of the fiber content in fresh GFB During the injection process Part 4 Determination of flexural strength; Simple Biegezugprüfung Part 5 Determination of flexural strength; Full Biegezugprüfung Part 6 Determination of water absorption by immersion method and the dry density Part 7 Determination of the moisture-dependent changes in length Part 8 of durability testing in the climate cycle test DIN EN 1171 Industrial valves - slide made of cast iron DIN EN 1172 Copper and copper alloys - Sheet and strip for building DIN EN 1173 Copper and copper alloys - state names DIN EN 1175, VDE 0117 Safety of industrial trucks - Electrical requirements Part 1 General requirements for trucks with battery-electric drive Part 2 General requirements for trucks with internal combustion engines Part 3 Particular requirements for electric power transmission systems of trucks with internal combust DIN EN 1176 playground equipment and playground Surfaces Part 1 General safety requirements and test methods Part 2 Additional specific safety requirements and test methods for swings Part 3 Additional specific safety requirements and test methods for slides Part 4 Additional specific safety requirements and test methods for cableways Part 5 Additional specific safety requirements and test methods for carousels Part 6 Additional specific safety requirements and test methods for rocking Part 7 Instructions for installation, inspection, maintenance and operational Part 10 Additional specific safety requirements and test methods for fully enclosed play equipment Part 11 Additional specific safety requirements and test methods for spatial network DIN EN 1177 Shock-absorbing playground surfacing - Determination of critical drop height DIN EN 1179 Zinc and zinc alloys - primary zinc
DIN EN 1183 Materials and articles in contact with foodstuffs - Test methods for thermal shock and the resistance DIN EN 1184 Materials and articles in contact with foodstuffs - Test methods for translucency of ceram DIN EN 1185 starches and starch derivatives - Determination of sulfur content - Acidimetrisches meth DIN EN 1186 Materials and articles in contact with foodstuffs - Plastics Part 1 Guidelines for the selection of conditions and test methods for overall migration Part 2 Test methods for overall migration into olive oil by total immersion Part 3 Test methods for overall migration into food simulants Aqueous by total immersion
Part Part Part Part Part Part Part Part Part Part
4 Test methods for overall migration into olive oil by cell 5 Test methods for overall migration into food simulants by Aqueous cell 6 Test methods for overall migration into olive oil using a pouch 7 Test methods for overall migration into food simulants Aqueous using a pouch 8 Test methods for overall migration into olive oil by article filling 9 Test methods for overall migration into food simulants Aqueous article by filling 10 Test methods for overall migration into olive oil (modified method for use in incomplete extrac 11 Test methods for overall migration into Mixtures of 14 C-labeled synthetic triglycerides 12 Test methods for overall migration at low Temperatures 13 Test methods for overall migration at High Temperatures
Part 14 Test methods for "substitute tests" for overall migration from plastics Intended to come into co foods, sodium iso-octane using test media and 95% ethanol
Part 15 Alternative test methods to migration into fatty food simulants by rapid extraction into iso-oct ethanol DIN EN 1191 Windows and doors - Resistance - Test method DIN EN 1192 Doors - Classification of strength requirements DIN EN 1194 Timber structures - Glued laminated timber - Strength classes and determination of char DIN EN 1195 Timber structures - Test methods - Load-bearing behavior Flooring
DIN EN 1196 gas-fired air heaters for domestic and non-domestic use - Supplementary requirements f heaters DIN EN 1197 Chemicals used for treatment of water Intended for human consumption - mono zinc pho DIN EN 1198 Chemicals used for treatment of water Intended for human consumption - monosodium DIN EN 1199 Chemicals used for treatment of water Intended for human consumption - disodium DIN EN 1200 Chemicals used for treatment of water Intended for human consumption - Trisodium pho DIN EN 1244 Adhesives - Determination of color and / or color change on exposure to light of Klebaufs DIN EN 1270 Playing field equipment - Basketball equipment - Functional and safety requirements, tes DIN EN 1315 Dimensions sorting Part 1: hardwood roundwood Part 2: Needle roundwood DIN EN 1316 hardwood roundwood quality sorting Part 2 Poplar DIN EN 1335 Office furniture - Office work chair Part 1 dimensions, Determination of dimensions Part 2 security requirements Part 3 safety checks DIN EN 1337 Structural bearings Part 4 roller bearings DIN EN 1338 Concrete paving blocks - Requirements and test methods DIN EN 1340 Concrete curb - Requirements and test methods DIN EN 1341 Slabs of natural stone for external paving - Requirements DIN EN 1342 Setts of natural stone for external paving - Requirements and test methods DIN EN 1343 Kerbs of natural stone for external paving - Requirements and test methods
DIN EN 1348 Adhesives for tiles - Determination of shear adhesion strength of cementitious mortar fo
DIN EN 1400 items for infants and young children - pacifier for infants and young children - Safety req methods
DIN EN 1505 Ventilation for buildings - Ductwork and fittings made of sheet metal with a rectangular c Dimensions DIN DIN DIN DIN DIN DIN DIN
EN EN EN EN EN EN EN
1506 1507 1530 1562 1610 1627 1643
Ventilation for buildings - Ductwork and fittings made of sheet metal with round cross-se Ventilation for buildings - Sheet metal air ducts Rectangular - Requirements for strength Door leaves - General and local flatness - Tolerance classes malleable Construction and testing of drains and sewers windows, doors, shutters - Burglar resistance - Requirements and classification Valve proving systems for automatic shut-off valves for gas burners and gas appliances
DIN EN 1717 Protection of drinking water from contamination in drinking water installations and gene devices DIN EN 1777 High rise aerial appliances for fire departments and rescue . aerial work platforms (HP) and testing DIN EN 1789 Medical vehicles and Their equipment - Road ambulances DIN EN 1822 filters (EPA, HEPA and ULPA) Part 1 Classification, performance testing, marking Part 2 Aerosol production, measuring equipment, particle counting Part 3 examination of the flat sheet filter media Part 4 leakage of filter elements (scan method) Part 5 the efficiency of filter element DIN EN 1837 Safety of machinery - Integrated lighting DIN EN 1838 Lighting - Emergency Lighting DIN EN 1839 Determination of explosion limits of gases and vapors
DIN EN 1841 Adhesives - Test methods for adhesives for floor and wall coverings - Determination of di of a linoleum floor covering in contact with adhesive on DIN EN 1846 Fire trucks with aerial ladder or platform ( High rise aerial appliances ) DIN EN 1854 Pressure sensing devices for gas burners and gas appliances DIN EN 1860 Appliances, solid fuels and firelighters for barbecuing Part 1 Grills for solid fuels; Requirements and test methods Part 2 barbecue charcoal charcoal and barbecue briquettes - Requirements and test methods Part 3 firelighters for barbecue charcoal and barbecue charcoal briquettes; Requirements and test me Part 4 grills for single use (disposable barbecues) in the use of solid fuels, requirements and test meth DIN EN 1925 Determination of water absorption coefficient by capillarity DIN EN 1926 Determination of compressive strength DIN EN 1974 Food processing machinery - Slicing machines - Safety and hygiene requirements DIN EN 1990 ( Euro Code 0) Basis of structural design DIN EN 1991 (Euro Code 1) Actions on structures
Part 1 General actions Part 1-1 Densities, self-weight and imposed loads for buildings Part 1-2 Fire Actions on structures Part 1-3 snow loads Part 1-4 wind loads Part 1-5 temperature effects Part 1-6 Actions during Execution Part 1-7 Unusual effects Traffic loads on bridges Part 2 Part 3 Actions induced by cranes and machinery Part 4 Actions on silos and tanks DIN EN 1992 (Euro Code 2) Design of Prestressed Concrete Structures Reinforced and Part 1: General rules Part 1-1 General rules and rules for buildings Part 1-2 Structural fire design case Part 2 Concrete bridges - Design and construction rules Part 3 silos and containers concrete structures DIN EN 1993 (Euro Code 3) Design of steel structures Part 1: General rules Part 1-1 General rules and rules for buildings Part 1-2 Structural fire design case Part 1-3 Supplementary rules for cold-formed members and sheeting Part 1-4 Supplementary rules for stainless steels of Part 1-5 Plated structural elements Part 1-6 strength and stability of shells Part 1-7 Plated structural elements of plane loading Part 1-8 Design of joints Part 1-9 fatigue Part 1-10 grades choices in terms of fracture toughness and through-thickness properties Part 1-11 Design of structures with tension steel Part 1-12 Additional rules for the extension of EN 1993 up to steel grades S700 Part 2 steel bridges Part 3 towers, masts and chimneys Part 3-1 towers and masts Part 3-2 chimneys Part 4 silos, tanks and pipelines Part 4-1 silos Part 4-2 container structures Part 4-3 pipes Part 5 Piling Part 6 runways
DIN EN 1994 (Euro Code 4) Design of composite steel and concrete structures Part 1: General rules Part 1-1 General rules and rules for buildings Part 1-2 Structural fire design case Part 2 General rules and rules for bridges DIN EN 1995 (Euro Code 5) Design and construction of wooden buildings Part 1: General rules Part 1-1 General rules and rules for buildings Part 1-2 Structural fire design case Part 2 bridges DIN EN 1996 (Euro Code 6) Design of masonry structures Part 1: General rules Part 1-1 General rules for reinforced and unreinforced masonry Part 1-2 Structural fire design case Part 2 Planning, selection of materials and execution of masonry Part 3 Simplified calculation methods for unreinforced masonry structures DIN EN 1997 (Euro Code 7) analysis and design in geotechnical engineering Part 1: General rules Part 2 of the ground investigation and testing DIN EN 1998 (Euro Code 8) Design of structures for earthquake resistance Part 1 General rules, seismic actions and rules for buildings Part 2 bridges Part 3 Assessment and retrofitting of buildings Part 4 silos, tanks and pipelines Part 5 Foundations, retaining structures and geotechnical aspects Part 7 is silent missing Part 6 towers, masts and chimneys Part 1: General rules DIN EN 1999 (Euro Code 9) Calculation and Design of aluminum structures Part 1: General rules Part 1-1 General rules Part 1-2 Structural fire design case Part 1-3 fatigue-stressed structures Part 1-4 Cold-formed profiled sheets Part 1-5 shell structures Part 2 fatigue-prone structures DIN EN 2000-9999 [ Edit ] DIN EN 2367 Aerospace; Cotter pins from steel EN 2573 DIN EN 3475 Aerospace series - Cables, electrical, aerospace, use - Test methods Part 100 General
Part 201 Visual inspection Part 202 mass Part 203 Dimensions Part 301 Conductor resistance Part 302 electric strength Part 303 Insulation Resistance Part 304 surface resistance Part 305 Overload Section 306 of the conductor continuity Part 307 corona extinction voltage Part 401 Accelerated aging Part 402 shrinkage and exfoliation Part 403 blocking and delamination Part 404 Thermal Shock Part 405 bending at room temperature Part 406 is wound with cold Part 407 flammability Part 408 fire resistance Part 409 aging in a closed, airtight space Part 410 Thermal service life Part 411 resistance to liquids Part 413 test Wrapping Part 414 DSC method Part 415 Rapid temperature changes 416. Thermal resistance Part 418 Thermal service life for conductors Part 501 notch strength Part 502 tear resistance Part 503 abrasion resistance Twist Part 504 Part 505 tensile strength of the individual wires and conductors Part 506-uniformity of the coating Part 507 adhesion strength of the coating Part 508 layer thickness of the coating Part 509 solderability Part 510 tensile strength and elongation of extruded insulation, protective covers and Coats Part 511 wear line to line Part 512 flexural fatigue strength Part 513 deformation resistance Part 601 smoke density Part 602 toxicity
Part 603 arc resistance, damp Part 604 arc resistance, dry Part 605 Behaviour after short circuit, moist Part 701 to strip and adhesive strength of the insulation on the conductor 702 Zurückschiebbarkeit part of the braid Part 703 Durability of manufacturer identification Part 704 flexibility Part 705 contrast measurement Part 706 UV laser marking Part 801 operating capacity Part 802 capacity difference Part 803 capacity deviation Part 804 propagation speed Part 805 impedance Damping part 806 Part 807 coupling resistance Part 808 crosstalk
DIN EN 3476 Aerospace series - Steel FE-PL1501 (30CrMo12) - Lufterschmolzen - Annealed - Forging s mm
DIN EN 3479 Aerospace series - Steel FE-PM1802 (X5CrNiCu15-5) - consumable electrode remelted - S precipitation Treated - plates - 6 mm
DIN EN 3480 Aerospace series - Steel FE-PA3601 (X6CrNiTi18-10) - Lufterschmolzen - Annealed - plate mm - 500 MPa ? Rm ? 700 MPa DIN EN 4108 Aerospace - ring inserts, open, interlocked with square drive
DIN EN 4219 Aerospace series - hexagon domed cap nuts, self-locking with plastic hood with normal a stainless steel DIN EN 9200 Aerospace series - Programme Management - Project Management policy for a specificat DIN EN 10000-19999 [ Edit ] DIN EN 10001 Definition and classification of pig iron DIN EN 10002 tensile test for metallic materials, December 2009 Replaced by DIN EN ISO 6892 DIN EN 10021 General technical delivery conditions for steel products DIN EN 10024 I-sections with taper flanges DIN EN 10025 Hot rolled products of structural steels Part 1: General technical delivery Part 2 Technical delivery conditions for non-alloy structural steels Part 3 Technical delivery conditions for normalized / normalized rolled weldable fine grain Part 4 Technical delivery conditions for thermomechanical rolled weldable fine grain Part 5 Technical delivery conditions for structural steels Part 6 Technical delivery conditions for flat products of high yield strength steels in the quenched and DIN EN 10027 Designation systems for steels
Part 1 Short name Part 2 number system DIN EN 10029 Hot rolled steel plates 3 ??mm thick or above; Tolerances and tolerances on shape EN 10045 Metallic materials; Charpy impact test. DIN EN 10055 Hot rolled steel equal tee with rounded edges and transitions DIN EN 10056 and unequal leg angles from Isosceles steel Part 1 Dimensions Part 2 Dimensional and shape tolerances DIN EN 10058 Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape an DIN EN 10059 Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape DIN EN 10060 Hot rolled round steel bars - Dimensions and tolerances on shape and tolerances DIN EN 10061 Hot rolled hexagon steel bars - Dimensions and tolerances on shape and tolerances DIN EN 10079 Definition of steel products DIN EN 10088 Stainless steels Part 1 List of stainless steels Part 2 Technical delivery conditions for sheet and strip of corrosion resisting steels for general purpose
Part 3 Technical delivery conditions for semi-finished products, bars, rods, wire, drawn wire, sections a corrosion resisting steels for general purposes Part 4 Technical delivery conditions for sheet and strip of corrosion resisting steels for construction
Part 5 Technical delivery conditions for bars, rods, wire, drawn wire, sections and bright products of co steels for construction DIN EN 10090 Valve steels and alloys for internal combustion engines DIN EN 10095 Heat resistant steels and nickel alloys DIN EN 10106 Cold-rolled non-oriented electrical steel sheet and strip delivered in the state DIN EN 10108 Round steel wire rod for cold FORMED nuts and bolts
DIN EN 10111 Continuously hot-rolled strip and sheet of low carbon steels for cold forming - Technical
DIN EN 10131 Cold-rolled flat products and coating with electrolytic zinc or zinc-nickel coating of low c strength steels for cold forming - Tolerances on shape and dimensions
DIN EN 10142 Continuously hot-dip galvanized strip and sheet of low carbon steels for cold forming - T conditions, September 2004 Replaced by DIN EN 10327 DIN EN 10143 Continuously hot-dip coated steel sheet and strip - Tolerances on shape and dimensions DIN EN 10152 electrolytically zinc coated cold rolled steel flat products for cold forming - Technical de DIN EN 10162 Cold rolled steel sections - Technical delivery conditions - Dimensional and shape tolera DIN EN 10163 Delivery requirements for surface condition of hot-rolled steel products (plates, wide fla DIN EN 10169 Continuously organic coated (coil coated) steel flat products Part 1 General information (definitions, materials, tolerances, test methods) Part 2 products for building exterior applications Part 3 Products for building interior DIN EN 10204 Metallic products Types of inspection documents DIN EN 10218 Steel wire and wire products Test methods Part 1
Part 2 wire Dimensions and tolerances DIN EN 10220 Seamless and welded steel tubes, general tables of dimensions and masses per unit le DIN EN 10226 Pipe threads where pressure tight on the threads Part 1 Taper external threads and parallel internal threads - Dimensions, tolerances and designation Part 2 Taper external threads and tapered internal threads - Dimensions, tolerances and designation Part 3 examination of limit gauges DIN EN 10241 Steel Fittings Threaded DIN EN 10242 Malleable DIN EN 10255 carbon steel tubes Suitable for welding and threading DIN EN 10270 Steel wire for springs Part 1 Patented cold drawn unalloyed spring steel wire Part 2 oil hardened and tempered spring steel wire Part 3 Stainless spring steel wire DIN EN 10278 Dimensions and tolerances of bright steel products DIN EN 10279 Hot rolled U-profile steel - Tolerances and tolerances on shape and limit Deviations of m DIN EN 10283 Corrosion resistant steel castings DIN EN 10291 Metallic materials - Uniaxial creep testing in tension - Method of test
DIN EN 10292 Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold delivery conditions DIN EN 10305 Steel tubes for precision applications - Technical delivery Seamless cold drawn tubes Part 1 Welded cold drawn tubes Part 2 Part 3 welded rolled tubes Seamless cold drawn tubes Part 4 for hydraulic and pneumatic power systems Welded cold sized square and rectangular tubes Part 5 cross-section Welded cold drawn tubes Part 6 for hydraulic and pneumatic power systems DIN EN 10326 Continuously hot-dip coated strip and sheet of structural steels - Technical delivery con
DIN EN 10327 Continuously hot-dip coated strip and sheet of low carbon steels for cold forming - Tech conditions
DIN EN 10336 Continuously hot-dip coated and electrolytically coated strip and sheet of multiphase st forming, technical specifications DIN EN 12004 Adhesives for tiles - Requirements, evaluation of conformity, classification and designat DIN EN 12056 Gravity drainage systems inside buildings Part 1: General requirements, design Part 2 waste water systems, planning and calculation Part 3 Roof drainage, layout and calculation Part 4 Wastewater lifting plants, layout and calculation Part 5 Installation and testing, instructions for operational, maintenance and use DIN EN 12057 Natural stone products - Modular tiles - Requirements DIN EN 12058 Natural stone products - Slabs for floors and stairs - Requirements DIN EN 12067 gas-air ratio controls for gas burners and gas appliances Part 1: Pneumatic version, June 2011 Replaced by DIN EN 88-1
Part 2: Electronic version DIN EN 12077 Cranes safety - health and safety requirements Part 2: Limiting and Indicating devices
DIN EN 12097 Ventilation for buildings - Ductwork - Requirements for ductwork components to Facilita ductwork systems DIN EN 12193 Light and lighting - Sports lighting DIN EN 12198 Safety of machinery - Assessment and reduction of the risk of radiation Emitted by mac Part 1: General principles Part 2 measurement methods for radiation emission Part 3 Reduction of radiation by attenuation or screening DIN EN 12208 Windows and doors - Water tightness - Classification DIN EN 12220 Ventilation for buildings - Ductwork - Dimensions of circular flanges for general ventilat
DIN EN 12237 Ventilation for buildings - Ductwork - Strength and leakage of air ducts of circular crossmetal DIN EN 12266 Industrial valves - Testing of metallic valves Part 1 Pressure tests, test procedures and acceptance criteria - Mandatory requirements Part 2 tests, test procedures and acceptance criteria; Additional requirements DIN EN 12373 Aluminium and aluminum alloys - Anodizing Part 1 Method for Specifying decorative and protective anodic oxidation coatings on aluminum Part 2 Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetri Part 3 Determination of thickness of anodic oxidation coatings; Non-destructive measurement beam m
Part 4 Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot tes treatment Part 5 Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
Part 6 of quality of sealed anodic oxidation test by deterministic mining the loss of mass after immers solution without prior acid treatment Part 7 Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass chromic acid solution with prior acid treatment Part 8 Determination of the comparative resistance of colored anodic oxidation coatings to ultraviolet
Part 9 Measurement of wear resistance and wear index of anodic oxidation coatings by abrasion test u tester to
Part 10 Measurement of mean specific abrasion resistance of anodic oxidation coatings by abrasion te test apparatus to
Part 11 Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angle or 85 °
Part 12 Measurement of reflectance characteristics of aluminum Surfaces using monitor integrating sp Part Part Part Part Part
13 14 15 16 17
measurement of the reflection characteristics of aluminum Surfaces with simplified or precisio Visual determination of image clarity of anodic oxidation coatings; Measuring grid method Assessment of resistance of anodic oxidation coatings to cracking by deformation Check for continuity of thin anodic oxidation coatings; Copper sulfate test Determination of electrical breakdown voltage
Part 18 assessment system for pitting corrosion; chart method Part 19 assessment system for pitting corrosion; Grid method DIN EN 12390 Testing hardened concrete Part 1 shape, dimensions and other requirements for specimens and molds Part 2 production and storage of specimens for strength tests Part 3 Compressive strength of test specimens Part 4 Determination of compressive strength; Specification for testing machines Part 5 flexural strength of test specimens Tensile splitting strength Part 6 of test specimens Density of hardened concrete Part 7 Part 8 of water under pressure Part 9 Freeze-thaw resistance - Scaling (pre-standard DIN CEN / TS 12390-9) DIN EN 12407 Natural stone test methods - Petrographic examination DIN EN 12440 Natural stone - Criteria for designation DIN EN 12445 gates; Safety in use of power operated doors; Test methods DIN EN 12453 gates; Safety in use of power operated doors; Requirements DIN EN 12464 Light and lighting - Lighting of work places Part 1 Work indoors Part 2 Outdoor workplaces DIN EN 12469 Biotechnology - Performance criteria for microbiological safety cabinets DIN EN 12566 Small wastewater treatment systems for up to 50 PT Part 1 Prefabricated septic pits Part 3 Packaged and / or site assembled domestic wastewater treatment plants for water Part 4 kits in situ from septic tanks Part 5 filtration systems for pre-treated domestic wastewater (Draft) Part 6 made systems for the Further treatment of the effluent from septic tank effluent (Draft) Part 7 The factory prefabricated units for cleaning a third part (Draft)
DIN EN 12568 Foot and leg protectors - Requirements and test methods for penetration-resistant inse caps DIN EN 12570 Industrial valves - Method for sizing the operating element DIN EN 12604 gates; Mechanical aspects; Requirements DIN EN 12605 gates; Mechanical aspects; Test methods DIN EN 12627 Industrial valves - welding ends for steel valves DIN EN 12644 Cranes - Information for use and testing Part 1 Operating instructions Part 2 labeling DIN EN 12665 ??Light and lighting, Basic terms and criteria for Specifying lighting requirements DIN EN 12670 terminology of natural stones - Petrographic designation DIN EN 12792 Ventilation for buildings - Symbols, terminology and graphical symbols DIN EN 12828 Safety equipment for heat generation plants DIN EN 12831 heating load of buildings (heating load)
DIN EN 12845 Fixed firefighting systems - Automatic sprinkler systems - Design, installation and main DIN EN 12952 Water-tube boilers and auxiliary installations DIN EN 12975 Thermal solar systems and components DIN EN 12999 Cranes - Cranes DIN EN 13000 Cranes - Mobile cranes DIN EN 13001 Cranes - General design Part 1: General principles and requirements Part 2 load effects DIN EN 13031 Greenhouses - Design and construction Part 1 Agricultural Greenhouses DIN EN 13032 Light and lighting - Measurement and presentation of photometric data of lamps and lig Part 1 Measurement and file format Part 1 Cor 1 Measurement and file format Part 2 Presentation of data for workplaces indoors and outdoors Part 2 Cor 1 Presentation of data for workplaces indoors and outdoors Part 3 representation of data for emergency lighting of work places DIN EN 13135 Cranes - Equipment Part 1 Cranes - Safety - Design - Requirements for equipment - Part 1: Electrical Equipment Part 2 Cranes - Equipment - Part 2: Non-electrotechnical equipment DIN EN 13155 Cranes - Lose Lastaufnahmemittel DIN EN 13157 Cranes - Safety - Hand powered lifting DIN EN 13162 Thermal insulation products for buildings - Factory made mineral wool (MW) DIN EN 13163 Thermal insulation products for buildings - Factory made products of expanded polystyr DIN EN 13164 Thermal insulation products for buildings - Factory made products of extruded polystyre DIN EN 13165 Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) DIN EN 13166 Thermal insulation products for buildings - Factory made products of phenolic foam (PF) DIN EN 13167 Thermal insulation products for buildings - Factory made products of cellular glass (CG) DIN EN 13168 Thermal insulation products for buildings - Factory made wood wool (WW) DIN EN 13169 Thermal insulation products for buildings - Factory made products of expanded perlite ( DIN EN 13170 Thermal insulation products for buildings - Factory made products of expanded cork (IC DIN EN 13171 Thermal insulation products for buildings - Factory made wood fiber (WF) DIN EN 13180 Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexi DIN EN 13201 street lighting Part 1 Selection of lighting classes Part 2 Quality features Part 3 Calculation of performance Part 3 Corrigendum 1 Calculation of performance Part 4 methods for measuring the quality characteristics of road lighting equipment DIN EN 13300 Paints and varnishes - Water-borne coating materials and coating systems for walls and DIN EN 13306 Terms of service DIN EN 13348 Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum
DIN EN 13373 Determination of geometric characteristics of rocks DIN EN 13374 Temporary Edge Protection Systems - Product requirements, test methods
DIN EN 13432 Packaging - Requirements for packaging recoverable through composting and biodegra and evaluation criteria for the classification of packaging; .cf.Biodegradable material . Biodegradability
DIN EN 13494 Thermal insulation products for building applications - Determination of tensile bond str adhesive mortar and thermal insulation as well as the base coat and heat insulation
DIN EN 13496 Thermal insulation products for building applications - Determination of the mechanical fiber fabric
DIN EN 13497 Thermal insulation products for building applications - Determination of impact resistan thermal insulation composite systems (ETICS)
DIN EN 13498 Thermal insulation products for building applications - Determination of the resistance t external thermal insulation composite systems (ETICS)
DIN EN 13499 Thermal insulation products for buildings - External thermal insulation composite system expanded polystyrene - Specifications
DIN EN 13500 Thermal insulation products for buildings - External thermal insulation composite system mineral wool - Specifications DIN EN 13523 Coil coated metals - Test methods Part 0 General introduction and list of test methods Part 1 layer thickness Part 2 shine Part 3 color distance Part 4 pencil hardness Part 5 Resistance to rapid deformation (impact test) Part 6 Adhesion after indentation (cupping test) Part 7 resistance to cracking on bending (T-bend test) Part 8 resistance to salt spray Part 9 resistance to immersion in water Part 10 Resistance to fluorescent UV radiation and condensation of water Part 11 Resistance to Solvents (rubbing test) Part 12 Resistance to scratching Part 13 Resistance to accelerated aging due to heat Part 14 chalks (accor ding method helmets) Part 15 metamerism Part 16 Resistance to abrasion Part 17 adhesive strength of peelable films Part 18 stain resistance Part 19 sample plates and method of atmospheric exposure Part 20 Adhesion of foam Part 21 Evaluation of outdoor exposed panels Part 22 color distance; Visual comparison Part 23 Colour stability in humid atmospheres Containing sulfur dioxide Part 24 blocks and stacking strength
Part 25 Resistance to moisture Part 26 Resistance to condensation Part 27 resistance to wet packing (cataplasm test) Part 29 Resistance to pollution DIN EN 13537 Requirements for Sleeping DIN EN 13557 Cranes - Controls and control stations DIN EN 13586 Cranes - Access DIN EN 13706 Specifications for pultruded profiles Part 1 Name Part 2 Test methods and general requirements Part 3 Special requirements DIN EN 13755 Water absorption at atmospheric pressure DIN EN 13779 Ventilation for non-residential buildings - Performance requirements for ventilation and systems and room cooling systems DIN EN 13830 Curtain walling - Product standard DIN EN 13852 Cranes - Offshore cranes Part 1 offshore cranes for general use Part 2 Floating Cranes DIN EN 13859 Flexible sheets for waterproofing - Definitions and characteristics of underlays tracks Part 1 underlays sheets for roofing Part 2 underlays for walls DIN EN 14043 automatic turntable ladders (Fire) DIN EN 14044 sequential aerial ladders / Platforms (HAB) DIN EN 14073 office furniture, office cabinets Part 2 Safety requirements Part 3 Test method for the determination of stability and strength of the structure
DIN EN 14079 Non-active medical devices - Performance requirements and test methods for absorben absorbent cotton and viscose DIN EN 14126 Infection Protection DIN EN 14142 Postal services Part 1 Components of postal addresses Part 2 Country-specific templates DIN EN 14153 Training of recreational scuba divers Part 1 Supervised diver Part 2 self divers Part 3 Dive Leader DIN EN 14175 Deductions Part 1 Definitions Part 2 requirements for safety and performance Part 3 examination procedures Part 4 on-site test methods Part 5 Recommendations for installation and maintenance (English version)
Part 6 prints with variable airflow Part 7 deductions for high thermal and acid loads (Special application fume cupboards)
DIN EN 14214 Automotive fuels - Fatty acid methyl ester (FAME) for diesel engines - Requirements and ( biodiesel ) DIN EN 14238 Cranes - Manually controlled manipulators DIN EN 14241 Chimneys - Requirements and test material for Elastomeric seals and sealing materials DIN EN 14411 Ceramic tiles - Definitions, classification, characteristics and marking DIN EN 14413 Recreational diving services - Safety related minimum requirements for the Training of Part 1 Level 1 Part 2 Level 2 DIN EN 14439 Cranes - Safety - Tower cranes DIN EN 14467 Recreational diving services - Requirements for recreational scuba diving service of DIN EN 14468 Table Tennis Part 1 of table tennis tables, functional and safety requirements, test methods Part 2 posts net assemblies - Requirements and test methods DIN EN 14470 Fire safety storage cabinets Part 1 Safety cabinets for flammable liquids Part 2 Safety cabinets for pressurized gas cylinders DIN EN 14492 Cranes - Power driven winches and hoists Power driven winches Part 1 Part 2 Power driven hoists DIN EN 14502 Cranes - Equipment for lifting persons Part 1 Suspended baskets Part 2 Elevating control stations DIN EN 14530 Plastics - Unsaturated polyester free-flowing molding compounds (PMC-UP) Part 1 Designation system and basis for specifications Part 2 Preparation of test specimens and determination of properties Part 3 Requirements for selected molding compounds DIN EN 14583 Workplace atmospheres - Volumetric bioaerosol sampling devices for - Requirements an DIN EN 14597 Temperature control devices and temperature for heat generating systems DIN EN 14604 smoke detector
DIN EN 14605 Protective clothing against liquid chemicals - Performance requirements for chemical pr with liquid-tight (Type 3) or spray-tight (Type 4) connections between the parts of clothing, Including i protection fo DIN EN 14634 Glass packaging - crown mouthpiece 26 H 180 - Dimensions DIN EN 14635 Glass packaging - crown mouthpiece 26 H 126 - Dimensions DIN EN 14719 Pulp, paper and board - Determination of diisopropylnaphthalene (DIPN) by solvent extr DIN EN 14798 Glass packaging - Manual Kronenkorköffner - Dimensions DIN EN 14877 plastic Surfaces in outdoor sports - Requirements DIN EN 14887 Glass packaging - Corkscrew - General requirements DIN EN 14985 Cranes - boom cranes DIN EN 15038 Translation Services - Service Requirements
DIN EN 15052 Resilient, textile and laminate floor coverings - Assessment and requirements on emiss organic compounds (VOC) (currently draft) DIN EN 15056 Cranes - Requirements spreader for container handling DIN EN 15085 Welding of railway vehicles DIN EN 15090 Footwear for firefighters DIN EN 15193 Energy performance of buildings - Energy requirements for lighting DIN EN 15241 Ventilation for buildings - Calculation methods for energy losses due to ventilation and buildings DIN EN 15242 Ventilation for buildings - Calculation methods for the determination of air flow rates in infiltration
DIN EN 15251 input parameters for the indoor environment for the design and evaluation of the energ buildings - indoor air quality, thermal environment, lighting and acoustics DIN EN 15330 for sports areas - Primarily designed for outdoor synthetic turf and needle felts Surface DIN EN 15376 Automotive fuels - Ethanol as a blending component for petrol - Requirements and test DIN EN 15423 Ventilation for buildings - Fire protection of ventilation systems in buildings DIN EN 15543 Glass packaging - Bottle Stoppers - Schraubmundstücke for bottles for non-carbonated DIN EN 15635 Steel static storage systems - Application and maintenance of storage facilities DIN EN 15800 Cylindrical helical springs made of round wire - Quality specifications for cold coiled com DIN EN 15883 washer disinfectorsPart 1: General requirements, definitions and test methods
Part 2 Requirements and tests for washer-disinfectors Employing thermal disinfection for surgical instr equipment, containers, utensils, glassware, etc. Part 3 Requirements and tests for washer-disinfectors Employing thermal disinfection for human waste Part 4 requirements and tests for washer-disinfectors Employing chemical disinfection for thermolabile
Part 5 Test soils and methods for cleaning Demonstrating efficacy (ISO / TS 15883-5: 2005); German v 15883-5: 2005
Part 6 Requirements and tests for washer-disinfectors Employing thermal disinfection for non-invasive devices and healthcare equipment DIN EN 16001 Energy management systems - Requirements with guidance for use DIN EN 16063 Packaging - Plastic Containers - Designation of plastic closure mouthpieces DIN EN 16064 Packaging - Plastic Containers - Plastic closure mouthpiece 30/25 H (18.5) DIN EN 16065 Packaging - Plastic Containers - Plastic closure mouthpiece L 30/25 (16.8) DIN EN 16066 Packaging - Plastic Containers - Plastic closure mouthpiece 26.7 (pitch 6.35) DIN EN 16067 Packaging - Plastic Containers - Plastic closure mouthpiece 26.7 (pitch 9.00) DIN EN 16068 Packaging - Plastic Containers - Plastic closure mouthpiece 38 DIN EN 16094 laminate flooring - Test methods for deterministic mining the micro-scratch resistance ( DIN EN 16287 Glass packaging - Schraubmundstücke for bottles with internal pressure - MCA 1 Mouth DIN EN 16288 Glass packaging - Schraubmundstücke for bottles with internal pressure - MCA 3 Mouth DIN EN 16289 Glass packaging - Schraubmundstücke for bottles with internal pressure - MCA 7.5 RF m DIN EN 16290 Glass packaging - Schraubmundstücke for bottles with internal pressure - MCA 7,5 R Mo DIN EN 16291 Glass packaging - Schraubmundstücke for bottles with internal pressure Part 1 Multi-MCA 2 Mouthpiece
Part 2 disposable MCA 2 Mouthpiece DIN EN 16292 Glass packaging - Schraubmundstücke - Flattened threads DIN EN 16293 Packaging - Glass packaging - Deep BVS finishes for silent wines DIN EN 16352 Logistics - Specifications for the reporting of crime DIN EN 20000-59999 [ Edit ] DIN EN 22553 Symbolic representation of welded joints and brazed DIN EN 27888 Water quality; Determination of electrical conductivity DIN EN 28601 date formats, September 2006 Replaced by DIN ISO 8601
DIN EN 28676 Hexagon head bolts with thread to the head; Fine thread M 8 × 1 to × 52 3 M (Product March 2001 Replaced by DIN EN ISO 8676 DIN EN 29692 Weld preparation DIN EN 45020 standardization and related activities - General Vocabulary (ISO / IEC Guide 2: 2004) DIN EN 50005 Industrial low-voltage switchgear; Terminal markings and direction indicators, General R
DIN EN 50020 Electrical apparatus for Potentially explosive atmospheres - Intrinsic safety "i"; August 2 DIN EN 60079-11 DIN EN 50523 for household use - Interworking Part 1 Functional Specification Part 2 data structures
DIN EN 50581 (VDE 0042-12) Technical documentation for the evaluation of electrical and electronic e regard to the restriction of hazardous substances DIN EN 50090 Electronic Systems for Home and Building (ESHG) Part 2 System Overview Part 2-1 Architecture Part 2-2 (VDE 0829-2-2) General technical requirements Part 2-3 (VDE 0829-2-3) requirements to functional safety for products did are Intended for installation Part 3 Applications of Part 3-1 Introduction to the application structure Part 3-2 application process ESHG class 1 Part 3-3 HBES Interworking model and common HBES data types Part 4 Independent medialayer Part 4-1 Application layer for HBES Class 1 Part 4-2-transport layer, network layer and general parts of data link layer for HBES Class 1 Part 4-3 Communication over IP (EN 13321-2) Part 5 Media and media dependent layers Part 5-1 Signalling on low-voltage electrical ESHG for Class 1 Part 5-2 Network based on HBES Class 1, two-wire cables (twisted pair) Part 5-3 signal transmission via radio Part 7-1 System Management - management procedures Part 8 of conformity assessment of products Part 9-1 Installation Requirements - wiring of two-wire lines ESHG class 1
DIN EN 50102 (DIN EN 62262, VDE 0470-100) protection provided by enclosures for electrical equipm against external mechanical impacts (IK code)
DIN EN 50107 fluorescent tube and pilot tube system with an open circuit voltage exceeding 1 kV but Part 1: General requirements Part 2 Requirements for earth fault protection devices and open circuit protection devices DIN EN 50110 (VDE 0105) Operation of electrical installations Part 1 (VDE 0105-1) Part 2 (VDE 0105-2) (national annexes) DIN EN 50117 coaxial cable Part 1 (VDE 0887-1) Generic specification Part 2 Sectional specification for cables for cable distribution Part 2-1 (VDE 0887-2-1) house wiring cable in the range of 5 MHz - 1000 MHz Part 2-2 (VDE 0887-2-2) outer cable in the range of 5 MHz - 1000 MHz Part 2-3 (VDE 0887-2-3) distribution and trunk cables for systems ranging from 5 MHz - 1000 MHz Part 2-4 (VDE 0887-2-4) House installation cable in the range of 5 MHz - 3000 MHz Part 2-5 (VDE 0887-2-5) outer cable in the range of 5 MHz - 3000 MHz Part 3 (VDE 0887-3) specification for drop cables
Part 3-1 (VDE 0887-3-1) Sectional specification for cables for telecommunications applications; Thumb communication systems Part 4 (VDE 0887-4) Sectional specification for distribution and trunk cables
Part 4-1 (VDE 0887-4-1) Sectional specification for cables BCT cabling in accor dance with EN 50173 in the range from 5 MHz to 3000 MHz Part 5 (VDE 0887-5) specification for house wiring cables for systems for frequencies from 5 MHz to 21 Part 6 (VDE 0887-6) specification for drop cables for systems for frequencies from 5 MHz to 2150 MHz
DIN EN 50128 Railway applications - Communication, signaling and processing systems - Software for protection systems DIN EN 50131 Alarm systems - Intrusion and hold-up systems Part 1 System Requirements Part 2-2 intruder alarm Part 2-3 Requirements for microwave detectors (DIN CLC / TS 50131-2-3) Part 2-4 Requirements for combined passive infrared and microwave detectors (DIN CLC / TS 50131-2 Part 2-5 Requirements for combined passive infrared and ultrasonic detectors (DIN CLC / TS 50131-2-5 Part 2-6 Requirements for opening detector (magnetic contacts) (DIN CLC / TS 50131-2-6) Part 3 Alarm Panel Part 4 signal generator Part 5-3 Requirements for using communication devices, the radio frequency techniques Part 6 power supplies Part 7 Application Rules Part 8 foggers / manure system for security applications DIN EN 50132 CCTV surveillance system for security applications DIN EN 50133 Alarm systems - Access control systems for use in security applications
Part 1 System Requirements Part 2-1 General requirements for system components Part 7 Application Rules DIN EN 50155 (VDE 0115-200) Railway applications - Electronic equipment used on rolling stock DIN EN 50172 safety lighting systems DIN EN 50173 Information technology - Generic cabling systems Part 1: General requirements Part 1, Supplement 1 cabling guide to help 10GBASE-T Part 2 office building Part 3 Industrial premises Part 4 apartments Part 4, Supplement 1 Implementation of BCT-network applications with cabling in accor dance with EN Part 5 datacenters DIN EN 50174 Information technology - Cabling installation DIN EN 50191 (VDE 0104) installation and operational of electrical test equipment DIN EN 50272 Safety requirements for secondary batteries and battery installations Part 1 (VDE 0510-1) General Safety Part 2 (VDE 0510-2) Stationary batteries Part 3 (VDE 0510-3) traction batteries for electric vehicles Part 4 (VDE 0510-104) batteries for portable devices DIN EN 50285 Energy efficiency of electric lamps for household use - Measurement DIN EN 50286 (VDE 0682-301) Electrical insulating protective clothing for use on low voltage installat DIN EN 50294 (VDE 0712-294) method for the measurement of total input power of ballast-lamp circu
DIN EN 50311 (VDE 0115-450) Railway applications - Rolling stock - DC Supplied electronic ballasts fo DIN EN 55022 (VDE 0878-22) Information technology equipment - Radio disturbance characteristics of measurement DIN EN 60000-99999 [ Edit ]
DIN EN 60044 Transducers Part 1: CT Part 2: Inductive voltage transformer (2012-05 Replaced by EN 61869-3) Part 3: Combined converter Part 6: CT requirements for protection purposes for transmission transient transmission behavior Part 7: Electronic voltage converter Part 8: Electronic Current Transformer DIN EN 60051 Direct acting Indicating measuring instruments and Their accessories - Gauges with an DIN EN 60061 Lamp caps and holders together with gauges for the control of interchangeability and s Part 1 lamp socket (IEC 60061-1) Part 2 Lampholders (IEC 60061-2) DIN EN 60062 Labeling of resistors and capacitors included date of manufacture, Replacing DIN 41314 DIN EN 60064 lamps for domestic and similar general lighting purposes - Performance requirements (
DIN EN 60081 Double-capped fluorescent lamps - Performance requirements (IEC 60081) DIN EN 60155 (VDE 0712-101) glow starter for fluorescent lamps (IEC 60155) DIN EN 60188 mercury vapor discharge lamps - Performance requirements (IEC 60188) DIN EN 60192 low pressure sodium lamps - Performance requirements (IEC 60192) DIN EN 60204 Safety of machinery - Electrical equipment of machines Part 1 General requirements DIN EN 60255 measuring relays and protection equipment Part 1: General requirements Part 5 Insulation coordination for measuring relays and protection equipment; Requirements and tests
Part 5, Supplement 1 Insulation coordination for measuring relays and protection equipment; Requirem Notes to the norm Part 8 Overload Relays
Part 11 Voltage dips, short-interruptions, voltage fluctuations and changes in the share connection for supply
Part 21-1 vibration, shock, bump and seismic tests on measuring relays and protection equipment; Se tests (sinusoidal)
Part 21-2 vibration, shock, bump and seismic tests on measuring relays and protection equipment; Se continuous shock tests Part 21-3 tests Part 22-1 Part 22-2 Part 22-3 Part 22-4 Part 22-5
vibration, shock, bump and seismic tests on measuring relays and protection equipment; Se Electrical Electrical Electrical Electrical Electrical
disturbance disturbance disturbance disturbance disturbance
tests tests tests tests tests
- Test for immunity to 1 MHz interference - tests with electrostatic discharge - Test for immunity to electromagnetic fields - Test for immunity to electrical nearly transient / burst for measuring relays and protection equipment; Immunity test S
Part 22-6 Electrical disturbance tests for measuring relays and protection equipment; Immunity to Con disturbances, induced by radio-frequency fields
Part 22-7 Electrical disturbance tests for measuring relays and protection equipment - Test for immun frequency interference Part 24 standard format for the exchange of transient data of electrical power grids Part 25 tests of electromagnetic radiation for measuring relays and protection equipment Part 26 requirements for electromagnetic compatibility Part 27 requirements for product safety Part 151 functional requirements for over / under current protection DIN EN 60384 Fixed capacitors for use in electronic equipment Part 1 Generic specification (VDE 0565-1) Part 2 ... 25 various specifications DIN EN 60400 (VDE 0616-3) Lampholders for tubular fluorescent lamps and starters (IEC 60400) DIN EN 60439 Low-voltage switchgear and controlgear assemblies Part 1 Type-tested and Partially type-tested assemblies Part 2 Particular requirements for busbar trunking
Part 3 Particular requirements for switchgear and low-voltage controlgear assemblies, Whose non-auth access; Distribution Boards
Part 4 Special requirements for construction sites (ACS)
Part 5: Special requirements for switchgear and low-voltage controlgear assemblies are installed did a places outdoors; Cable distribution cabinets (KVS) in power supply networks DIN EN 60529 (VDE 0470-1) protection provided by enclosures (IP Code) (IEC 60529) DIN EN 60598 lights Part 1 (VDE 0711-1) General requirements and tests (IEC 60598-1) Part 2 Particular requirements Part 2-2 (VDE 0711-2-2) Recessed Lighting (IEC 60598-2-2) Part 2-3 (VDE 0711-2-3) lamps for street and road lighting (IEC 60598-2-3) Part 2-4 (VDE 0711-2-4) portable luminaires for general use (IEC 60598-2-4) Part 2-5 (VDE 0711-2-5 :) headlights (IEC 60598-2-5) Part 2-6 (VDE 0711-206) lights with built-in transformers for filament lamps (IEC 60598-2-6) Part 2-7 Portable garden lamps (IEC 60598-2-7) Part 2-8 (VDE 0711-2-8) Hand lamps (IEC 60598-2-8) Part 2-9 (VDE 0711-2-9) photo and movie recording lamps (not professional application) (IEC 60598-2 Part 2-10 (VDE 0711-2-10) portable luminaires for children (IEC 60598-2-10) Part 2-11 (VDE 0711-2-11) Aquarium Lights (IEC 60598-2-11) Part 2-12 (VDE 0711-2-12) AC outlets Night Lights (IEC 60598-2-12) Part 2-13 (VDE 0711-2-13) ground luminaires (IEC 60598-2-13) Part 2-18 (VDE 0711-2-18) lighting for pools and similar applications (IEC 60598-2-18) Part 2-19 (VDE 0711-2-19) Air Leading lights (safety requirements) Part 2-20 (VDE 0711-2-20) light chains (IEC 60598-2-20) Part 2-22 (VDE 0711-2-22) Luminaires for emergency lighting Part 2-23 (VDE 0711-2-23) Low voltage lighting systems for filament lamps (IEC 60598-2-23) Part 2-24 (VDE 0711-2-24) Lamps with limited surface temperature (IEC 60598-2-24) Part 2-25 (VDE 0711-2-25) lamps for use in clinical areas of hospitals and health care buildings (IEC 60 DIN EN 60601 Medical electrical equipment, safety DIN EN 60603 connectors for printed circuits for frequencies below 3 MHz
Part 1 Generic specification: General requirements and guide for the preparation of detail specification assessment (IEC 60603-1)
Part 2 Detail specification for quality Reviewed indirect connectors for printed circuits, 2.54 mm (0.1 in mounting features (IEC 60603-2)
Part 3 Indirect connectors for printed circuits with 2.54 mm (0.1 in) contact spacing and offset connec distance (IEC 60603-3)
Part 4 Indirect connectors for printed circuits with 1.91 mm (0.075 in) contact spacing and offset conn distance (IEC 60603-4) Part 5 connector for direct and indirect Plug connector for double-coated circuit boards with 2.54 mm spacing (IEC 60603-5) Part 6 Direct connectors and connectors for printed circuits with 2.54 mm (0.1 in) contact spacing for coated circuit boards with 1.6 mm (0.063 in) nominal thickness (IEC 60603-6)
Part 7 Detail specification for connectors with Assessed quality, 8P, Including Both fixed and free conn features plug (IEC 60603-7)
Part 7-1 Detail specification for shielded, free and fixed connectors, 8-pin, plug with common characte quality (IEC 60603-7-1) Part 7-3 Detail specification for shielded, free and fixed connectors, 8 pin, for data transmissions with 100 MHz (IEC 48B / 1707 / CDV)
Part 7-4 Detail specification for unshielded, free and fixed connectors, 8 pin, for data transmissions up 60603-7-4)
Part 7-7 Detail specification for shielded, free and fixed connectors, 8-pin, for data transmissions up to 60603-7-7)
Part 8 Indirect connectors for printed circuits; 2.54 mm (0.1 in) Cross section of the male contacts 0.63 (IEC 60603-8) Part 9 Indirect connectors for printed circuits, back panels and cable connection, 2.54 mm (0.1 in) (IEC Part 10 Indirect connectors for printed circuits with 2.54 mm (0.1 in), inverted design (IEC 60603-10)
Part 12 Detail specification for dimensions, general requirements and tests for a number of sockets fo integrated circuits (IEC 60603-12) Part 13 Detail specification for quality Reviewed indirect connectors for printed circuits with 2.54 mm connectors for IDC termination (ID) (IEC 60603-13)
Part 14 Detail specification for circular connectors for low frequency audio and video applications: suc and audiovisual equipment (IEC 60603-14) DIN EN 60617 Graphical symbols for diagrams DIN EN 60662 sodium vapor high pressure lamps (IEC 60662) DIN EN 60721 Classification of environmental conditions Part 1 Preferred values ??for predictors Part 3 classes of environmental parameters and Their severities Part 3-0 Introduction Part 3-1 long-term storage Part 3-2 Transport Part 3-3 Stationary use at weather protected, Part 3-4 Stationary use at non-weather-protected Part of 3-5 and use in land vehicles Part 3-6 use on ships Part 3-7 Transportable use Part 3-9 micro climates within products DIN EN 60730 Automatic electrical automatic control devices for household and similar use ( VDE 063 Part 1: General requirements Part 2 Particular requirements (various standards) DIN EN 60751 Industrial platinum resistance thermometers and platinum temperature sensors DIN EN 60825 Safety of laser products Supplement 1. National wording of signs for laser radiation Supplement 9 Compilation of maximum permissible exposure to incoherent optical radiation Supplement 10 Application guidelines and explanatory notes to IEC 60825-1 Supplement 14: A Guide for Users Part 1 Equipment classification and requirements Part 2: Safety of optical fiber communication systems (OFCS)
Part 2, Supplement 1 Safety of optical fiber communication systems (OFCS), construction sheet 1 Part 4 Laser guards Part 12 Safety of free space optical communication systems for information transmission DIN EN 60848 GRAFCET specification language for sequential function charts control DIN EN 60870 Telecontrol equipment and systems (IEC 60870) Part 1: General considerations, Technical Report Part 2 Operating conditions Part 3 interfaces (electrical characteristics) Part 4 requirements for the performance Part 5 About conference proceedings Part 6 telecontrol protocols DIN EN 60901 Single-capped fluorescent lamps - Performance requirements (IEC 60901) DIN EN 60921, VDE 0712-11 ballasts for tubular fluorescent lamps - Performance requirements (IEC 60
DIN EN 60923 VDE 0712-13 Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluo Performance requirements (IEC 60923)
DIN EN 60925, VDE 0712-21 dc Supplied electronic ballasts for tubular fluorescent lamps - Performanc 60925)
DIN EN 60927, VDE 0712-15 Auxiliaries for lamps - Starting devices (other than glow starters) - Perfor (IEC 60927)
DIN EN 60929, VDE 0712-23 AC Supplied electronic ballasts for tubular fluorescent lamps - Performan 60929) DIN EN 60947 Low Voltage Switchgear DIN EN 60968, VDE 0715-6: 2000-04 ballasted lamps for general lighting services - Safety requiremen DIN EN 60969 Self-ballasted lamps for general lighting services - Performance requirements (IEC 6096 DIN EN 61000 EMC Electromagnetic Compatibility Part 1 Overview of IEC 61000-4 series Part 2 Test for immunity to electrostatic discharge Part 3 Test for immunity to radio frequency electromagnetic fields Part 4 Test for immunity to electrical nearly transient / burst Part 5 Test for immunity to voltage surges Immunity to Conducted disturbances Part 6, induced by radio-frequency fields
Part 7 General guidelines for methods and apparatus for measurement of harmonics and interharmon networks and connected devices Part 8 Test for immunity to magnetic fields with power frequencies Part 9 immunity test Pulse magnetic field Part 10 Immunity test damped oscillatory magnetic field Part 11 Immunity Test Voltage dips, short-interruptions and voltage variations Part 12 Immunity test damped sinusoidal oscillations
Part 13 Test of immunity to the AC power connector to harmonics and interharmonics Including mains the signal transmission on low-voltage electrical Part 14 Immunity test voltage fluctuations Part 15 Flicker - Functional Description We design specification
Part Part Part Part Part Part Part Part Part Part Part Part
16 17 18 20 21 23 24 25 27 28 29 30
testing for immunity to Conducted, common mode disturbances in the frequency range 0 Hz t Immunity Test AC Ripple on dc input power port Immunity Test oscillating waves measurement of the emission and immunity in transverse electromagnetic wave guides procedures for examination in the reverberation chamber test methods for equipment for protection against HEMP and other radiated emissions test methods for protective devices for HEMP Conducted disturbances - Basic EMC testing for immunity of equipment and systems against HEMP disturbances Immunity Test asymmetry of the supply voltage Immunity Test fluctuations in energy-related frequency Immunity Test Voltage dips, Kurzzeitunterbechungen and voltage variations on DC power inpu Method for measuring voltage quality
Part 33 immunity test for equipment with input current> 16 A per phase Voltage dips, short-interrupti variations
DIN EN 61010 Safety requirements for electrical equipment for measurement, control and laboratory Part 1: General requirements Part 2-010 Particular requirements for laboratory equipment for the heating of materials Part 2-020 Particular requirements for laboratory centrifuges Part 2-032 Particular requirements for hand-held and hand-manipulated current sensors for electrical Part 2-040 Particular requirements for sterilizers and washer disinfectors used to treat medical-materi Part 2-051 Particular requirements for laboratory equipment for mixing and stirring Part 2-061 Particular requirements for laboratory atomic spectrometers with thermal atomization and
Part 2-081 Particular requirements for automatic and semi-automatic laboratory equipment for analys purposes Part 2-101 Particular requirements for in vitro diagnostic (IVD) medical devices Part 031 Safety requirements for hand-held probe assemblies for electrical measurement and testing
DIN EN 61048 (VDE 0560-61) Auxiliaries for lamps - Capacitors for fluorescent lamp and other dischar General and safety requirements (IEC 61048)
DIN EN 61049, VDE 0560-62 capacitors for discharge lamps plants, Especially fluorescent lighting syst requirements (IEC 61049) DIN EN 61131 Programmable Logic Controllers (PLC) Part 1 General information (IEC 61131-1) Part 2 Equipment requirements and tests (IEC 61131-2) Part 3 Programming Languages ??(IEC 61131-3) Chapter 5 Communication (IEC 61131-5) Part 7 fuzzy control programming (IEC 61131-7)
DIN EN 61140 (VDE 0140-1) Protection against electric shock - Common aspects for installation and e 61140) DIN EN 61167 metal halide lamps (IEC 61167) DIN EN 61195, VDE 0715-8 Double-capped fluorescent lamps - Safety requirements (IEC 61195) DIN EN 61199, VDE 0715-9 Single-capped fluorescent lamps - Safety requirements (IEC 61199)
DIN EN 61228 UV lamps for tanning purposes - Methods of measurement and description (IEC 61228)
DIN EN 61305 Hi-Fi devices and systems for home use - Methods of measuring and Specifying the per characteristics Part 1 General Part 2 FM radio reception parts Part 3 amplifier Part 5 speakers Part 5, Supplement 1 hearing tests for Speakers - Particular test and paired comparison
DIN EN 61346 Industrial systems, installations and equipment and industrial products - Structuring pri reference designations Part 1: General rules Part 2 Classification of objects and codes for classes DIN EN 61347 Auxiliaries for lamps Part 1 (VDE 0712-30) General and safety requirements (IEC 61347-1) Part 2 Particular requirements Part 2-1 (VDE 0712-31) Particular requirements for starting devices (other than glow starters) (IEC 613
Part 2-2 (VDE 0712-32) Particular requirements for dc or ac Supplied electronic convertors for filamen 2)
Part 2-3 (VDE 0712-33) Particular requirements for ac Supplied electronic ballasts for fluorescent lamp Part 2-4 (VDE 0712-34) Particular requirements for dc Supplied electronic ballasts for general lighting
Part 2-5 (VDE 0712-35) Particular requirements for dc Supplied electronic ballasts for lighting public tr 2-5)
Part 2-6 (VDE 0712-36) Particular requirements for dc Supplied electronic ballasts for lighting of aircra
Part 2-7 (VDE 0712-37) Particular requirements for dc Supplied electronic ballasts for emergency light Part 2-8 (VDE 0712-38) Specific requirements for ballasts for fluorescent lamps (IEC 61347-2-8)
Part 2-9 (VDE 0712-39) Specific requirements for ballasts for discharge lamps (excluding fluorescent la 9)
Part 2-10 (VDE 0712-40) Special requirements for electronic inverters and converters for high-frequen start tubular discharge lamps (neon tubes) (IEC 61347-2-10) Part 2-11 (VDE 0712-41) Special requirements for electronic circuits used with luminaires (IEC 61347-2
Part 2-12 (VDE 0712-42) Particular requirements for dc or ac Supplied electronic ballasts for discharge fluorescent lamps) (IEC 61347-2-12)
Part 2-13 (VDE 0712-43) Particular requirements for dc or ac Supplied electronic control gear for LED m 2-13) DIN EN 61355 Classification and designation of documents for plants, systems and facilities DIN EN 61439 Low-voltage switchgear and controlgear assemblies Part 1 General requirements Part 2 power switchgear and controlgear assemblies Part 3 Installation distributors for use by unskilled persons (IVL) Part 5 switchgear assemblies in public power distribution networks
Busbar trunking systems Part 6 (busways) DIN EN 61499 function blocks for Industrial Control System (IEC 61499) Part 1 Architecture Part 2 requirements for software tools Part 4 rules for standardized profiles DIN EN 61508 Functional safety of electrical / electronic / programmable electronic systems (VDE 080 Part 0 (VDE 0803 Supplement 1) Functional safety and IEC 61508 (IEC / TR 61508-0) Part 1 (VDE 0803-1) General requirements (IEC 61508-1)
Part 2 (VDE 0803-2) requirements for safety-related electrical / electronic / programmable electronic s 2) Part 3 (VDE 0803-3) software requirements (IEC 61508-3) Part 4 (VDE 0803-4) Terms and Abbreviations (IEC 61508-4) Part 5 (VDE 0803-5) Examples and methods for the determination of safety integrity levels (IEC 61508 Part 6 (VDE 0803-6) Guidelines on the application to IEC 61508-2 and IEC 61508-3 (IEC 61508-6) Part 7 (VDE 0803-7) Overview of techniques and measures (IEC 61508-7) DIN EN 61549, VDE 0715-12 Special lamps (IEC 61549) DIN EN 61672 Electroacoustics - Sound Level Meters Part 1 requirements (IEC 61672-1) Part 2 type tests (IEC 61672) Part 3 Periodic determination (IEC 61672-3)
DIN EN 61669 Electroacoustics - Instruments for measuring characteristics of hearing aids to the hum 2001)
DIN EN 61724 Performance monitoring of photovoltaic systems - Guidelines for measurement, data ex (IEC 61724: 1998) DIN EN 61725 Analytical representation for solar radiation profiles days (IEC 61725: 1997) DIN EN 61800 Adjustable speed electrical power drive
Part 1 (VDE 0160 Part 101) General Requirements- down for the design of low-voltage DC drive system
Part 2 (VDE 0160 Part 102) General Requirements- down for the design of low-voltage DC drive system frequency - (IEC 61800-2) Part 3 (VDE 0160 Part 103) EMC requirements and specific test methods (IEC 61800-3)
Part 4 (VDE 0160 Part 104) General requirements; Specification for the Design of AC drive systems tha not exceeding 35 kV (IEC 61800-4) Part 5-1 (VDE 0160 Part 105) safety requirements; Electrical, thermal and energy (IEC 61800-5-1) DIN EN 61850 Communication networks and systems in substations (IEC 61850) Supplement 1. Introduction and Overview Part 3 General requirements Part 4 system and project management Chapter 5 Communication requirements for functions and device models
Part 6 language for the description of the configuration for communication in substations with intellige devices (IEDs) Part 7 Basic communication structure for station- and feeder equipment
Part Part Part Part
7-1 7-2 7-3 7-4
Principles and models Abstract communication service interface (ACSI) Common data classes Compatible logical and data classes
Part 7-410 Communication networks and systems for automation in the electrical power supply - Part power plants - Communication for monitoring, regulation and control (IEC 61850-7-410) Part 7-420 communication systems for distributed power supply - Logical node
Part 8-1 Specific Communication Service Mapping (SCSM) - pictures on MMS (ISO 9506-1 and ISO 9506 8802-3
Part 9-1 Specific Communication Service Mapping (SCSM) - Sampled values ??over serial simplex mult connection Part 9-2 Specific Communication Service Mapping (SCSM) - Sampled values ??over ISO / IEC 8802-3 Part 10 compliance audit DIN EN 61920 Non-Line-infrared applications (IEC 61920: 2004) DIN EN 61947 Electrical projection - Measurement and documentation of key performance Part 1 fixed resolution projectors Part 2 projectors variable resolution DIN EN 61966 Multimedia systems and equipment - Colour measurement and management Part 2 color management Part 2-1 Default RGB color space, sRGB (IEC 61966-2-1) Part 2-2 Extended RGB color space, scRGB (IEC 61966-2-2) Part 2-4 Extended YCC color space for video applications - xvYCC (IEC 61966-2-4) Part 2-5 Optional RGB color space - opRGB (IEC 61966-2-5) Part 3 units with cathode ray tubes (IEC 61966-3) Part 4 apparatus with liquid crystal displays (IEC 61966-4) Part 5 devices with plasma displays (IEC 61966-5) Part 6 Electronic projectors for front projection (IEC 61966-6) Part 7 Color Printer Part 7-1 Reflective prints - RGB inputs (IEC 61966-7-1) Part 8 Multimedia Color Scanner (IEC 61966-8) Part 9 Digital Cameras (IEC 61966-9) DIN EN 61988 plasma screens Part 1 Terminology and letter symbols (IEC 61988-1) Part 2 measurement methods Part 2-1 Optical (IEC 61988-2-1) Part 2-2 Opto-Electrical (IEC 61988-2-2) Part 3-1 Mechanical interface (IEC 61988-3-1) Part 4 environmental, durability and mechanical test methods (IEC 61988-4) DIN EN 62031 (VDE 0715-5) LED modules for general lighting - Safety requirements (IEC 62031)
DIN EN 62034 (VDE 0711-400) Automatic test systems for battery powered emergency lighting for es 62034) DIN EN 62035, VDE 0715-10 discharge lamps (excluding fluorescent lamps) - Safety requirements (IEC
DIN EN 62079 Preparation of instructions - Structuring, content and presentation (Withdrawn and Rep DIN EN 62106 Specification of the Radio Data System (RDS) DIN EN 62264 Integration of enterprise computing and control systems Part 1 Models and terminology (Draft standard DIN IEC 62264-1) Part 2 attributes of the object model (Draft standard DIN IEC 62264-2) Part 3 activity models for operational production management DIN EN 62304 Medical Device Software - Software Life Cycle Processes DIN EN 62563 Medical electrical equipment - Medical image display systems Part 1 valuation methods (IEC 62563-1: 2009) DIN EN 80000 Quantities and Units Part 6 electromagnetism DIN EN 80601 Medical electrical equipment, safety DIN EN 82045 Document Management Part 1 Principles and methods (IEC 82045-1: 2001) Part 2 metadata and reference information models (IEC 82045-2: 2004) DIN EN 82079 Preparation of instructions - Structuring, content and presentation DIN EN 88528 generating sets with reciprocating internal combustion engines Part 11 Dynamic, uninterruptible power supply - Performance requirements and test methods DIN EN 100000 from [ Edit ] DIN EN 100012 Basic Specification: X-ray of the electronics components
DIN EN 300366 Private Integrated Services Network (PISN) - signaling between telecommunication sy characteristics "recall"
DIN EN 383001 Telecommunications and Internet together leading services and protocols for next-gen (TISPAN) - interaction between Session Initiation Protocol (SIP) and transmission control protocol indep ISDN User Part DIN EN ISO 1-9999 [ Edit ] DIN EN ISO 1 reference temperature for geometrical product specification and testing
DIN EN ISO 60 Determination of apparent density of molding material can be poured from a did specifi density )
DIN EN ISO 61 Plastics - Determination of apparent density of molding materials can not be poured did funnel ( packing density ) DIN EN ISO 62 Plastics - Determination of water absorption DIN EN ISO 75 Plastics - Determination of temperature of deflection Part 1 General method Part 2 Plastics and ebonite Part 3 Highly resistant thermosetting laminates and long-fiber-reinforced plastics DIN EN ISO 90 terms and procedures for deterministic mining the dimensions and volume Part 1 Falzdeckeldosen Part 2 Resealable metal packaging
Part 3 aerosol cans DIN EN ISO 105 Textiles - Tests for color fastness Part A01 General test specifications Part A04 method for the instrumental assessment of staining of Adjacent fabrics Part A05 Instrumental assesing change in color to mine the deterministic Graumaßstabszal Part A08 vocabulary of colorimetry Part B01 Colour fastness to light: Daylight Part B02 Colour fastness to artificial light: Xenon arc light Part B03 Colour fastness to weathering: weathering outdoors Part B04 Colour fastness to artificial weathering: Xenon arc light Part B05 detection and assessment of photochromism Part B06 color fastness and aging to artificial light at High Temperatures: Xenon arc lamp Part B07 Colour fastness to light of textiles wetted with artificial sweat Part B08 verification of blue light fastness types of wool fabric 1 to 7 Part B10 Artificial weathering - Exposure to filtered xenon-arc radiation Part C06 Colour fastness to domestic and commercial laundering laundry Part C07 color fastness of wet, pigment printed textiles to brush
Part C08 Colour fastness to domestic and commercial laundering using a non-phosphate reference de a low temperature bleach activator
Part C09 color fastness against oxidative bleaching in the household and commercial laundering using reference detergent Incorporating a low temperature bleach activator Part C10 Colour fastness to washing with soap or soap and soda Part C12 Colour fastness to industrial laundering Part D01 fastness to dry cleaning solvent with Perchlorethylene Part D02 determination of rubbing fastness: Organise solvent Part E01 Colour fastness to water Part E02 Colour fastness to sea water Part E03 Colour fastness to chlorinated water (swimming-pool water) Part E04 Colour fastness to perspiration Part E05 Colour fastness to spotting: Acid Part E06 Colour fastness to spotting: Alkali Part E07 Colour fastness to spotting: Water Part E09 Colour fastness to boiling water (potting) Part E12 Colour fastness to Walken: Alkaline Walke Part E16 Colour fastness to water stains on upholstery fabrics Part G02 Colour fastness to combustion gases Part G03 Colour fastness to ozone in the atmosphere Part J01 basis for the measurement of body colors Part J03 Calculation of color differences
Part J05 method for deterministic mining the instrumental Farbinkonstanz a sample when changing th (CMCCON02) Part P02 Colour fastness to pleating: Dampfplissieren
Part X12 Colour fastness to rubbing Part X16 Colour fastness to rubbing, small areas Part X18 deterministic mining The Possibility of yellowing by phenol Part Z06 migration assessment of dyes and pigments Part Z07 Determination of solubility and solution stability of water-soluble dyes DIN EN ISO 128 Technical Drawings, General principles of presentation DIN EN ISO 139 Textiles - Standard atmospheres for conditioning and testing DIN EN ISO 140 Acoustics - Measurement of sound insulation in buildings and of building elements Part 4 Measurement of airborne sound insulation between rooms Part 5 Measurement of airborne sound insulation of facade elements and facades of buildings Part 7 measurements of impact sound insulation of floors in buildings Part 14 Guidelines for special situations and conditions Part 18 of the measurement Caused by rainfall to parts sound in the test DIN EN ISO 148 Metallic materials - Charpy impact test Charpy Test methods Part 1 Part 2 Examination of testing machines (pendulum impact) DIN EN ISO 150 Rohleinöl, linseed oil and linseed oil for paints - Specifications and test DIN EN ISO 172 Plastics - Phenolic plastic Molding - Detection of free ammonia DIN EN ISO 175 Plastics - Methods of measuring the performance against liquid chemicals DIN EN ISO 176 Plastics - Determination of plasticizer levy - activated carbon process DIN EN ISO 177 Plastics - Determination of migration of Plasticizers DIN EN ISO 178 Plastics - Determination of flexural properties DIN EN ISO 179 Plastics - Determination of Charpy impact properties Part 1 Non-instrumented impact test Instrumented impact testing Part 2 DIN EN ISO 180 Plastics - Determination of Izod -Schlagzähigkeit
DIN EN ISO 182 Plastics - Determination of the tendency of compounds and products based on vinyl c and copolymer to make hydrochloric acid and other acidic products at elevated Temperatures Part 2 pH meter method Part 3 conductivity method Part 4 Potentiometric method DIN EN ISO 204 Metallic materials - Uniaxial creep testing in tension - Test methods
DIN EN ISO 216 Writing paper and Certain classes of printed matter - Trimmed sizes - A and B series a machine direction DIN EN ISO 225 Fasteners - Screws and nuts - Dimensions DIN EN ISO 228 pipe thread DIN EN ISO 252 Conveyor belts - Ply adhesion between the components - Test methods DIN EN ISO 266 Acoustics - standard frequencies DIN EN ISO 276 binders for paints - linseed stand oil - Requirements and test methods DIN EN ISO 277 Binders for paints and varnishes - Raw processing oil - Requirements and test method DIN EN ISO 283 textile conveyor belts - Tensile strength at full belt thickness, elongation at break and broad-based strength - Test methods
DIN EN ISO 284 Conveyor belts - Electrical conductivity - Specification and test methods DIN EN ISO 286 Geometrical product specifications (GPS) - ISO system for linear dimensions Part 1 Basis of tolerances, fits and Deviations Part 2 Tables of standard tolerance grades and limit Deviations for holes and shafts DIN EN ISO 287 Paper and board - Determination of moisture content of a lot - drying method DIN EN ISO 291 Plastics - Standard atmospheres for conditioning and testing DIN EN ISO 293 Plastics - Compression molded test specimens of thermoplastic materials DIN EN ISO 294 Plastics - Injection molding of test specimens of thermoplastic materials Part 1: General principles, and molding of multipurpose and bar test specimens Part 2 Small tensile bars Part 3 Small plates Part 4 Determination of molding
Part 5 Plastics - Injection molding of test specimens of thermoplastic materials - Part 5: Preparation of for investigating anisotropy DIN EN ISO 295 Plastics - Pressing of test specimens of thermosetting materials
DIN EN ISO 305 Plastics - Determination of thermal stability of polyvinyl chloride (PVC), related chlorin homopolymer and copolymer and Their molding compounds - Discoloration method DIN EN ISO 306 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST DIN EN ISO 307 Plastics - Polyamide - Determination of viscosity
DIN EN ISO 308 Plastics - Phenolic molding materials - Determination of acetone-soluble fraction (app the molding Compositions unprocessed) DIN EN ISO 340 Conveyor belts - Fire behavior in laboratory testing - Requirements and test methods DIN EN ISO 354 Acoustics - Measurement of sound absorption in a reverberation room DIN EN ISO 376 Metallic materials - Calibration of force-measuring devices for the testing of uniaxial t DIN EN ISO 377 Steel and steel products - Location and preparation of samples and test pieces for me DIN EN ISO 385 Laboratory glassware - Burettes DIN EN ISO 389 Acoustics - Reference zero for the calibration of audiometric equipment Part 1 Reference equivalent threshold sound pressure levels for pure tones and supra-aural headphon Part 2 Reference equivalent threshold sound pressure levels for pure tones and insert earphones Part 3 Reference equivalent threshold force levels for pure tones and bone conduction receiver Part 4 reference level for narrow-band masking noise Part 5 Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 k Part 6 Reference equivalent threshold sound pressure levels for acoustic short-term test signal Part 7 Bezugshörschwellen under free-field and diffuse-field conditions Part 8 Reference equivalent threshold sound pressure levels for pure tones and circumaural earphone Part 9 preference measurement conditions for the determination of reference hearing threshold levels DIN EN ISO 407: Protective gloves against thermal risks (heat and / or fire) DIN EN ISO 439 Steel and iron - Determination of total silicon content - Gravimetric method DIN EN ISO 445 pallets for handling of goods - Terminology
DIN EN ISO 463 Geometrical product specifications (GPS) - Dimensional measuring equipment - Desig characteristics of mechanical dial gauges DIN EN ISO 472 Plastics - List of technical terms
DIN EN ISO 483 Plastics - Small chambers for conditioning and testing at constant relative humidity Aq DIN EN ISO 489 Plastics - Determination of refractive index DIN EN ISO 505 Conveyor belts - Determination of tear resistance of textile conveyor belts DIN EN ISO 520 grains and legumes - Determination of the 1000 grain mass DIN EN ISO 527 Plastics - Determination of tensile properties Part 1 General principles Part 2 Test conditions for molding and extrusion Part 3 Test conditions for films and sheets Part 4 Test conditions for isotropic and anisotropic fiber-reinforced plastic composites Part 5 Test conditions for unidirectional fiber-reinforced plastic composites DIN EN ISO 534 Paper and board - Determination of thickness, density and specific volume DIN EN ISO 535 Paper and board - Determination of water absorption capacity DIN EN ISO 536 Paper and board - Determination of grammage DIN EN ISO 542 Oilseeds - Sampling
DIN EN ISO 544 Welding consumables - Technical delivery conditions for welding filler metals and fluxe dimensions, tolerances and designation
DIN EN ISO 580 Plastics piping and ducting systems - injection molded thermoplastic plastics fittings assessment of the effects due to heat exposure DIN EN ISO 583 textile conveyor belts - Total thickness and thickness of the constituent elements - Tes DIN EN ISO 584 Plastics - Unsaturated polyester resins - Determination of reactivity at 80 ° C (Conven DIN EN ISO 585 Plastics - Unplasticized cellulose acetate - Determination of moisture content DIN EN ISO 591 titanium dioxide pigments Part 1 Requirements and test methods DIN EN ISO 595 Reusable medical glass syringes or syringes made of glass and metal Part 2 construction, functional requirements and tests DIN EN ISO 604 Plastics - Determination of pressure characteristics
DIN EN ISO 636 Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non steels - Classification DIN EN ISO 638 paper, board and pulps - Determination of dry matter content - drying method DIN EN ISO 642 steel - end quench test (Jominy test) DIN EN ISO 643 steel - Micrographic determination of the apparent grain size DIN EN ISO 648 Laboratory glassware - Volumetric pipettes DIN EN ISO 658 Oilseeds - Determination of content of Impurities DIN EN ISO 659 Oilseeds - Determination of oil content (Reference method) DIN EN ISO 660 Animal and vegetable fats and oils - Determination of acid value and acidity DIN EN ISO 661 Animal and vegetable fats and oils - Preparation of test sample DIN EN ISO 662 Animal and vegetable fats and oils - Determination of moisture and volatile matter DIN EN ISO 663 Animal and vegetable fats and oils - Determination of percentage of insoluble Impurit DIN EN ISO 664 Oilseeds - Reduction of laboratory sample to the test sample DIN EN ISO 665 Oilseeds - Determination of moisture and volatile matter DIN EN ISO 669 Resistance welding - Resistance welding equipment - Mechanical and electrical requir DIN EN ISO 676 Spices and condiments - Botanical nomenclature
DIN EN ISO 683 for heat treatment steels, alloy steels and free-cutting steels Part 17 bearing steels DIN EN ISO 703 Conveyor belts - flexibility in the transverse direction (trough ability) - Test methods DIN EN ISO 707 Milk and milk products - Guidance on sampling DIN EN ISO 712 Cereals and cereal products - Determination of moisture content - Reference method DIN EN ISO 717 Acoustics - Rating of sound insulation in buildings and of building elements Part 1 airborne sound insulation Part 2 Impact sound insulation DIN EN ISO 734 Oilseed meals - Determination of oil content Part 1 extraction method with hexane (or petroleum ether) Part 2 rapid extraction method DIN EN ISO 748 Hydrometrie - Flow measurement in open channels by Means of flow velocity meters o DIN EN ISO 772 Hydrometry - Vocabulary and symbols DIN EN ISO 780 Packaging - Pictorial marking for handling of goods DIN EN ISO 787 General methods of test for pigments and fillers Part 7 Determination of residue on sieve - Water method - Handspülverfahren Part 11 Determination of tamped volume and tapped density (1995) Part 13 Determination of water-soluble sulfates, chlorides and nitrates Part 14 Determination of the resistivity of the Aqueous extract Part 25 Comparison of the color of white, black and colored pigments in full shade systems - colorimet DIN EN ISO 801 Pulps - Determination of commercial mass of delivery items Part 1 sheet pulp in bales Part 3 big bales DIN EN ISO 835 Laboratory glassware - Graduated pipettes DIN EN ISO 844 Rigid cellular plastics - Determination of compression properties DIN EN ISO 845 Cellular rubbers and plastics - Determination of bulk density DIN EN ISO 846 Plastics - Determination of the action of microorganisms on plastics
DIN EN ISO 862 Packaging - Child-resistant packaging - Requirements and test methods for non-reclos non-pharmaceutical products DIN EN ISO 868 Plastics and ebonite - Determination of indentation hardness with a durometer (Shore DIN EN ISO 877 Plastics - weathering Part 1 General Guide Part 2 weathering and irradiating behind window glass Part 3 Accelerated weathering with concentrated solar radiation DIN EN ISO 887 Plain washers for metric bolts and nuts for general applications - General Overview DIN EN ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel Part 2 Nuts with specified property classes - Coarse thread and fine thread Part 5 screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine Part 6 Nuts with specified proof load values; Fine thread, August 2012 Replaced by DIN EN ISO 898-2 DIN EN ISO 899 Plastics - Determination of creep Part 1 Tensile creep
DIN EN ISO 945 microstructure of cast iron Part 1 Graphite classification by visual analysis DIN EN ISO 1043 Plastics - Symbols and abbreviations Part 1 Basic polymers and Their special characteristics Part 2 fillers and reinforcing agents Part 3 plasticizer Part 4 flame retardants
DIN EN ISO 1101 Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of fo location and run
DIN EN ISO 1302 Geometrical product specifications, specification of surface texture in technical prod
DIN EN ISO 1456 Metallic and other inorganic coatings - Electrodeposited coatings of nickel, nickel plu plus nickel and copper plus nickel plus chromium DIN EN ISO 1463 Metallic and oxide - layer thickness measurement - Microscopic method DIN EN ISO 1513 Paints and varnishes - and preparation of samples DIN EN ISO 1514 Paints and varnishes - Standard panels DIN EN ISO 1518 Paints and varnishes - Determination of scratch resistance Part 1 method with constant load Part 2 method with Continuously Increasing load DIN EN ISO 1519 Paints and varnishes - Bend test (cylindrical mandrel) DIN EN ISO 1520 Paints and varnishes - Cupping test DIN EN ISO 1522 Paints and varnishes - Pendulum damping test DIN EN ISO 1524 Paints and varnishes and printing inks - Determination of fineness (graininess)
DIN EN ISO 2064 Metallic and other inorganic coatings - Definitions and conventions: concerning the m thickness DIN EN ISO 2178 Non-magnetic coatings on magnetic substrate - Measurement of coating thickness -
DIN EN ISO 2360 Non-conductive coatings on non-magnetic metallic basis materials - Measurement of Eddy current method
DIN EN ISO 2361 Electroplated nickel coatings on magnetic and non-magnetic substrate - Measureme thickness - Magnetic method DIN EN ISO 2409 Paints and varnishes - Cross-cut test DIN EN ISO 2808 Paints and varnishes - Determination of film thickness DIN EN ISO 3098 Technical product documentation, fonts Part 0 ground rules Part 2 Latin alphabet, numerals and symbols Part 3 Greek alphabet Part 4 Diacritical and special characters in the Latin alphabet Part 5 CAD signature of the Latin alphabet and numbers and signs Part 6 Cyrillic alphabet DIN EN ISO 3166 codes for the names of countries and Their subdivisions Part 1 codes for country names
DIN EN ISO 3497 Metallic coatings - coating thickness measurement - X-ray fluorescence method DIN EN ISO 3543 Metallic and non-metallic coatings - thickness measurement - Beta backscatter meth DIN EN ISO 3668 Paints and varnishes - Visual comparison of the color of coatings
DIN EN ISO 3682 Binders for paints and varnishes - Determination of acid value - Titrimetric method, J by DIN EN ISO 2114
DIN EN ISO 3740 guidelines on the application of the basic standards for the determination of sound p sources
DIN EN ISO 3744 Acoustics - Determination of sound power levels of noise sources using sound pressu engineering method 2 for at Essentially free field over a reflecting DIN EN ISO 3882 Metallic and other inorganic coatings - Review of methods for coating thickness mea DIN EN ISO 4014 Hexagon head screws with shank DIN EN ISO 4017 Hexagon head bolts with thread to the head DIN EN ISO 4063 Manual arc welding
DIN EN ISO 4287 Geometrical product specifications (GPS) - Surface texture: Profile method - Terms, d surface texture parameters
DIN EN ISO 4288 Geometrical product specifications (GPS) - Surface texture: Profile method - Rules an assessment of surface texture DIN EN ISO 4762 screws with hexagon socket DIN EN ISO 4892 Plastics - Methods of exposure to laboratory light equipment Part 1 General Guide Xenon arc lamps Part 2 Part 3 UV lamps DIN EN ISO 5436 Geometrical product specifications (GPS) - Surface texture: Profile method; Normal Part 1 Material Measures Part 2 Normal software DIN EN ISO 6270 Paints and varnishes - Determination of resistance to moisture Part 1 Continuous condensation Part 2 Procedure for exposing test specimens in condensation
DIN EN ISO 6385 Ergonomic principles in the design of work systems (Replaced since 2004, DIN 33400 26385 the Following: 1990-12) DIN EN ISO 7092 Plain washers - Small series, Product grade A DIN EN ISO 7093 Plain washers - Large series Part 1 Product grade A Part 2 Product grade C DIN EN ISO 8256 Plastics - Determination of tensile impact
DIN EN ISO 8402 quality management concepts (German / English / French) in January 2001 Replaced Supplement 1, Quality Management, comments on terms. Withdrawn without replacement in February DIN EN ISO 8676 Hexagon head bolts with thread to the head and metric fine pitch thread, product gr DIN EN ISO 9000 Quality Management Systems , Fundamentals and vocabulary DIN EN ISO 9001 quality management system requirements DIN EN ISO 9004 Quality management systems Guidelines for performance improvements
DIN EN ISO 9241 Ergonomic requirements for office work with visual display terminals Part 1: General introduction Part 2 Requirements for work tasks - Principles Part 3 Requirements for visual displays Part 4 requirements for keyboards Part 5 requirements for workplace design and posture Part 6 requirements for the work environment Part 7 Requirements for visual display with reflections Part 8 Requirements for Displayed colors Part 9 Requirements Input Devices - Keyboards except Part 11 requirements for serviceability - Principles Part 12 information representation Part 13 user guide Part 14 dialoging using menus Part 15 dialoging with command languages Part 16 dialoging by direct manipulation Part 17 dialoging using screen forms Part 110 Dialogue principles (replaces the previous Part 10) Part 151 guidelines for designing user interfaces for the World Wide Web Part 171 guidelines for software accessibility Part 300 Introduction to requirements and measurement techniques for electronic visual displays Part 302 Terminology for electronic visual displays Part 303 requirements for electronic visual displays Part 304 test method for power users Part 305 Optical laboratory test methods for electronic visual displays Part 306 on-site assessment methods for electronic visual displays Part 307 analysis and compliance test methods for electronic visual displays Part 309 displays with organic light emitting diodes Part 400 Principles and requirements for physical input devices Part 410 Design criteria for physical input devices DIN EN ISO 9509 Water quality - Toxicity test for deterministic mining the inhibition of nitrification in a DIN EN ISO 9921 Ergonomics - Assessment of speech communication DIN EN ISO 9999 Technical aids for disabled persons DIN EN ISO 10000-99999 [ Edit ]
DIN EN ISO 10075 Ergonomic principles related to mental workload Part 1 General terms and definitions Part 2 design principles Part 3 Principles and requirements: concerning methods for measuring and assesing mental workload DIN EN ISO 10545 Ceramic tiles Part 1 sample acceptance and bases for the adoption
Part 2 Determination of dimensions and surface finish Part 3 Determination of water absorption, apparent porosity, apparent relative density and bulk densit Part 4 Determination of flexural strength and fracture load Part 5 Determination of impact resistance by measurement of coefficient of restitution Part 6 Determination of resistance to deep abrasion for unglazed tiles Part 7 Determination of resistance to surface abrasion for glazed tiles Part 8 Determination of linear thermal expansion Part 9 Determination of thermal resistance Part 10 Determination of Moisture expansion Part 11 Determination of the resistance to crazing for glazed tiles Part 12 Determination of frost resistance Part 13 Determination of chemical resistance Part 14 Determination of resistance to staining Part 15 Determination of the release of lead and cadmium Part 16 Determination of small color differences DIN EN ISO 10628 Flow diagrams for process plants - General rules
DIN EN ISO 10848 Acoustics - Laboratory measurement of the flanking transmission of airborne and im between adjoining rooms Part 1 Framework Document Part 2 application on lightweight components, When The compound has little influence Part 3 Application to lightweight components, if the compound has significant influence Part 4 All other cases DIN EN ISO 11199 crutches for beidarmige handling Part 1 Walking frames Part 2 Rollators Part 3 walker DIN EN ISO 11609 Dentistry - toothpastes - Requirements, test methods and marking DIN EN ISO 12100 Safety of machinery - Basic concepts - risk assessment and risk reduction DIN EN ISO 13406 Ergonomic requirements for work with visual displays based on flat panels Part 1 Introduction Part 2 Ergonomic requirements for flat screens DIN EN ISO 13407 -centered design Processes for interactive systems DIN EN ISO 13485 Medical devices - Quality management systems - Requirements for regulatory purp DIN EN ISO 13802 Plastics - Verification of pendulum impact - Charpy, Izod and tensile impact DIN EN ISO 13850 Safety of machinery - Emergency stop - Principles for design DIN EN ISO 14121 Safety of machinery - Risk assessment Part 1 Summary DIN EN ISO 14122 Permanent Means of access to machinery Part 1 Choice of fixed Means of access between two levels Part 2 Working platforms and walkways Part 3 stairs . stepladders and railings
Part 4 Fixed ladders DIN EN ISO 14583 flathead screws with hexagon socket DIN EN ISO 14644 Cleanrooms and associated controlled room areas Part 1 Classification of air cleanliness Part 2 Specifications for testing and monitoring to prove continued compliance with ISO 14644-1 Part 3 test methods Part 4 design, implementation and start-up Part 5 operating Part 6 Terminology Part 7 SD Module (clean air hoods, Gloveboxes, isolators and mini-environments) Part 8 Classification of airborne molecular contamination Part 9 Classification of particulate surface cleanliness (currently draft) DIN EN ISO 14688 Geotechnical investigation and testing - Identification and classification of soil Part 1 Name and description Part 2 Basics of Soil classifications DIN EN ISO 14689 Geotechnical investigation and testing - Identification and classification of rock Part 1 Name and description DIN EN ISO 14971 Medical devices - Application of risk management to medical devices DIN EN ISO 15502 household refrigerator / freezers - Characteristics and test methods DIN EN ISO 15536 ??Ergonomics - Computer manikins and body outline template Part 1: General requirements Part 2 examination of the functions and validation of measurements of Compuer manikin systems DIN EN ISO 15854 Dentistry - Casting and baseplate waxes DIN EN ISO 15883 washer disinfectorsPart 1: General requirements, definitions and test methods
Part 2 Requirements and tests for washer-disinfectors Employing thermal disinfection for surgical instr equipment , Containers, utensils, glassware, etc. Part 3 Requirements and tests for washer-disinfectors Employing thermal disinfection for human waste Part 4 requirements and tests for washer-disinfectors Employing chemical disinfection for thermolabile Part 5 Test soils and methods for Demonstrating cleaning effect (currently DIN ISO / TS 15883-5)
Part 6 Requirements and tests for washer-disinfectors Employing thermal disinfection for non-invasive devices and healthcare equipment (currently draft)
DIN EN ISO 16911 Stationary source emissions - Manual and automatic determination of velocity and Part 1 Manual Reference Method Part 2 Continuous measurement methods DIN EN ISO / IEC 17025 General requirements for the competence of testing and calibration laboratori DIN EN ISO 19011 Guidelines for Audits of quality management and / or environmental management DIN EN ISO 20344 Personal protective equipment - Test methods for footwear DIN EN ISO 20345 Personal protective equipment - Safety Footwear DIN EN ISO 20346 Personal protective equipment - safety shoes DIN EN ISO 20347 Personal protective equipment - Occupational Shoes
DIN EN ISO 20567 Paints and varnishes - Determination of stone impact resistance of coatings Part 1 multi-impact test Part 2 Single impact test with a guided impact body Part 3 Single impact test with free flying impact body DIN EN ISO 22475 Geotechnical investigation and testing - Sampling methods and groundwater meas Part 1 Technical Principles of execution Part 2 Qualification criteria for enterprises and personnel Part 3 Conformity assessment of enterprises and personnel by a certification body DIN EN ISO 22476 Geotechnical investigation and testing - Field testing Part 1 CPTs with electrical transducers and systems for measuring the pore water pressure Part 2 probing Part 3 Standard Penetration Test Part 4 Pressiometerversuch by Ménard Part 5 Experiment with the flexible dilatometer Part 6 experiment with the self-drilling pressure meter (in preparation) Part 7 page compression test Part 8 experiment with the Verdrängungspressiometer (in preparation) Part 9 wing shear test Part 10 weight exploratory Part 11 Flachdilatometerversuch Part 12 CPTs with mechanical transducers Part 13 stress test with shallow foundations (in preparation) DIN EN ISO 81714 Design of graphical symbols for the applications of technical product documentatio Part 1 Basic Rules DIN IEC [ Edit ] DIN IEC 60038 IEC standard voltages DIN IEC 60050 International Electrotechnical Vocabulary
DIN IEC 60912 Nuclear instrumentation - ECL (emitter coupled logic) -Signalverbindungen on front pan DIN IEC 62198 Risk Management for Projects - Application Guide DIN IEC 62481 digital living network alliance (DLNA) Interoperability Guidelines for devices in the hom Part 2 media formats DIN ISO and ISO / IEC [ Edit ]
DIN ISO 6 Photographer - system of black and white negative films and Their processing for shooting s of ISO speed DIN ISO 43 Aerospace - jacking points on the aircraft DIN ISO 272Fasteners; Wrench sizes for hexagon bolts and nuts ISO 281 bearings; Dynamic load ratings and rating life Supplement 1 factor a (DIN) and calculation of the expanded adjusted life Supplement 2 to ISO 281/1 Explanations: 1977
Supplement 3 Estimating of the contamination or pollution level for rolling bearings in closed industria DIN ISO 286 limits and fits Part 1 Basis of tolerances, fits and Deviations Part 2 Tables of standard tolerance grades and limit Deviations for holes and shafts DIN ISO 517 Photography - opening ratios and related variables in camera lenses - Designations and m DIN ISO 1302 Technical drawings, details of the surface texture, June 2002 Replaced by DIN EN ISO 13 DIN ISO 1585 Road vehicles - Method for deterministic mining the net output of engines ISO 1629 Rubber and latices, classification designation, DIN ISO 1940 Mechanical vibration - Balance quality requirements for rotors in a constant (rigid) state Part 1 Specification and verification of balance tolerances Part 2 variations in balancing DIN ISO 2108 Information and documentation - International Standard Book Number (ISBN) DIN ISO 2240 Photography - Camera color reversal films - Determination of ISO speed DIN ISO 2768 General tolerances Part 1 Tolerances for linear and angular dimensions without individual tolerance indications Part 2 tolerances for features without individual tolerance indications DIN ISO 2859 Acceptance sampling based on the number of defective units or defects (attribute testin Part 1 by acceptance quality limit (AQL) ordered sampling plan for the examination of a series of lots
Part 2 After the rückzuweisenden quality level (QL) ordered sampling plan for the examination of indiv on the number of defective units Part 3 skip lot procedures Part 4 methods for the assessment of quality-declared levels DIN ISO 2936 screws and nuts - angle screwdriver for screws with hexagon socket DIN ISO 3166 codes for the names of countries and Their subdivisions Part 2 Code for names of countries under module only Part 3 Code for formerly used names of countries DIN ISO 3297 Information and Documentation, International Standard Serial Number (ISSN) DIN ISO 3302 Rubber - Tolerances for products Part 1 dimensional tolerances Part 2 of geometric dimensioning and tolerancing DIN ISO 3310 Test sieves - Technical requirements and testing Part 1 Test sieves of metal wire cloth Part 2 Test sieves of perforated metal sheets Part 3 Test sieves of electroformed sheets DIN ISO 4219 Air quality - Determination of gaseous sulfur compounds in ambient air - Sampling equip DIN ISO 5455 Technical drawings, standards DIN ISO 5800 Photography - color negative films for breastfeeding photography - Determination of ISO DIN ISO 6411 Technical drawings Simplified representation of center holes DIN ISO 7000 Graphical symbols on equipment - Index and Overview DIN ISO 7331 ski poles for alpine skiing - Safety requirements and tests DIN ISO 8601 Data elements and interchange formats - Information interchange - Representation of d
DIN ISO 9175 character tubes for hand-held devices Ink Pen Part 1 Definitions, dimensions, designation and marking Part 2 WITHDRAWN Construction, requirements and testing, July 2006 without replacement DIN ISO 9276 representation of the results of particle size analysis Part 1: Graphical representation Part 2: Calculation of average particle sizes / -durchmessern And moments from particle size distribut Part 4: Characterization of a separation process Part 6: The description and quantification of particle shape and morphology DIN ISO 10002 Quality management - Customer satisfaction - Guidelines for complaints handling in O DIN ISO 10005 Guidelines for Quality Plan DIN ISO 10007 Guidelines for configuration management DIN ISO 10110 Preparation of drawings for optical elements and systems Supplement 1. Comparison of ISO 10110 - DIN 3140; Index Part 1 General Part 2 material error - stress birefringence Part 3 flaws - bubbles and inclusions Part 4 material error - inhomogeneities and streaks Part 5 form errors Part 5, Supplement 1 matching error, pass error checking with sample glasses Part 6 centering, Part 7 surface defects Part 8 surface quality Part 9 surface treatments and coatings Part 10 shown in tabular form Part 11 General tolerances for values ??without tolerances Part 12 Aspheric Surfaces Part 14 tolerances for wavefront deformations Part 17 damage threshold for laser radiation
ISO / IEC 10561Information technology - Text and office systems - Printers Class 1 and Class 2; Method mining the printer power DIN ISO 10602 Photography - Processed black and white films from the silver-gelatin type - Specificati DIN ISO 10957 Information and documentation - International standard music number (ISMN)
DIN ISO 11798 Information and documentation - aging resistance of fonts, printing and copying on pa and test methods DIN ISO 13321 particle size analysis - Photon correlation spectroscopy DIN ISO 14887 Sample Preparation - Method for dispersing powders into liquids DIN ISO 15489 Information and documentation - Records management Part 1 General DIN ISO 16016 Protection notices for Restricting the use of documents and products DIN ISO 23601 safety signs - escape plan DIN ISO 29990 Learning services for the education and training - Basic requirements for service DIN ISO 80601 Medical electrical equipment
DIN ISO / IEC 2022 Information technology - Character code structure and extension techniques
DIN ISO / IEC 27001 Information technology - Security techniques - Information security management Requirements DIN ISO / IEC 27002 Information technology - Security techniques - Guidelines for information security
ISO / IEC 28360 Information technology - Office equipment - Determination of chemical emission rates equipment DIN VDE [ Edit ] lake List of DIN VDE Standards LN Standards (aviation) [ edit ] LN LN LN LN
7-1 straight pins 9092 profiles tubes; Dimensions, static values 9118-2 rivet holes; Reductions and Durchzugswarzung 71412 Cone grease nipple with metric thread, latest edition September 1970
VG standards (for "defense equipment", the German Federal Office of Defense Technology and Procure edited) [ edit ] VG 58260 Medical instruments - Ligature Needles by Deschamps, current June 1994 edition VG 72632 Tarnscheinwerfer Part 1 splash proof, current edition December 1991 VG 81208 maneuvering of ships Part 20 runout test Part 21 oblique towing test, current edition August 1991 Part 22 wind tunnel test VG 81244 boatbuilding wood Part 1 medium strength and elasticity values ??for solid wood, latest edition August 1991 Part 2 Allowable stress, safety factors Part 3 Application and Processing Part 4 pretreatment, quality requirements, quality assurance VG 81259 Cathodic protection of ships; External protection by impressed current Part 1 Definitions cost bases, arrangement demands on the coating, the latest edition January 1994 Part 2 Electrical installation, monitoring, current edition January 1994 Part 3 anodes, Shield, Electrodes, measurement, current edition January 1994 VG 84519 eyeplates for slips toppers, design fundamentals, current January 2009 edition VG 85057 glands, current edition February 1990 VG 85092 upholstered furniture for bed and bunk beds, latest edition September 2009 VG 85305 Replenishment at sea; double tube clamps, current June 1994 edition VG 85494 Replenishment at sea; Counter-points, current edition July 1992
VG 85528 ??Cable plans for submarines - Identifier for the connection of cable shields, current Decem VG 95034 Technical Documents - reference to use rights, a February 2007 issue VG 95821 application of standards and other rules - liability, ranking, current edition 06.2009
VG 96936 conduits, pipes, guard channels Part 10 Metallic braid hoses and braided conductor, detail specification, date October 2007 edition
Part 10 Supplement 1 Metallic braid hoses; Cross-reference list for standardization of types, current D edition Part 11 conduits, shielded, specification details, latest edition September 1996
Part 11 Supplement 1, conduits, shielded; Cross-reference list for standardization of types, current edi 1996 VG 96953 Erdungsmaterial Part 9: Earth screws, detail specification, date May 2010 Issue