diagrama hidraulico 320D caterpillarDescription complète
diagrama hidraulico 320D caterpillar
Descripción completa
DIAGRAMA ELECTRICO CAT C15 BITURBODescripción completa
Descripción completa
Diagrama del sistema eléctrico CAT 16M3Full description
Cat 6cr 320b Diagrama ElectricoDescription complète
Esquema Eléctrico de motores y su lógica de reparaciónDescripción completa
cat c18Full description
Descripción: cat c18
fFull description
engine cat c18Full description
Dumbele
Full description
ELE PartituraFull description
Descripción completa
Descripción: manual de partes c18
apostila de estalações eletrica maritimaDescrição completa
INTERACTIVE SCHEMATIC Bookmarks
*This document is best viewed at a screen resolution of 1024 X 768. To set your screen resolution do the following: RIGHT CLICK on the DESKTOP. Select PROPERTIES. CLICK the SETTINGS TAB . MOVE THE SLIDER under SCREEN RESOLUTION until it shows 1024 X 768. CLICK OK to apply the resolution.
The Bookmarks panel will allow you to quickly navigate to points of interest.
EC-C2 EC-C3
*Due to different monitor sizes and PDF reader preferences there may be some variance in linked schematic locations
Click here to save a copy of this interactive schematic to your desktop
E-C60 E-C61
VIEW ALL CALLOUTS EC-C1
Click on any text that is BLUE BLUE and and underlined. These are hyperlinks that can be used to navigate the schematic and machine views.
When only one callout is showing on a machine view, clicking on this button will make all of the callouts visible. This button is located in the top right corner of every machine view page.
ELECTRICAL SYMBOLS
HOTKEYS (Keyboard Shortcuts)
BASIC HYDRAULIC COMPONENTSYMBOLS
T
FUNCTION
KEYS
Zoom In
“CTRL” / “+”
Zoom Out
“CTRL” / “-”
Fit to Page
“CTRL” / “0” (zero)
Hand Tool
“SPACEBAR” (hold down)
Find
“CTRL” / “F”
Search
“CTRL” / “SHIFT” / “F”
Pressure Switch
Temperature Switch
Level Switch
Flow Switch
Circuit Breaker
Click here to view the Schematic Symbols and Definitions page
Pump or Motor
Variability
Fluid Conditioner
Spring (Adjustable)
UENR3226-01 October 2016
C18 SCAC Marine Radiator Genset Electrical System JHL1-740 DTP1-461
Line Restriction Variable and Pressure Compensated
2-Section Pump
Attachment
Pump: Variable and Pressure Compensated
Bidirectional
VARIABLE DISPLACEMENT NON- COMPENSATED
CYLINDERS
Four-Way
Unidirectional
Bidirectional
CONTROL A B
A B
P T
P T
Single Acting
FIXED DISPLACEMENT DISPLACEMENT
Shifted Position
Normal Position
MOTORS
Double Acting
Infinite Position
CHECK
ACCUMULATORS Basic Symbol
Spring Loaded
Shuttle
Unidirectional
Bidirectional
VARIABLE DISPLACEMENT NON- COMPENSATED
Pilot Controlled
Spring Loaded Gas Charged
Unidirectional
Bidirectional MAIN AUX.
PILOT CONTROL
ROTATING SHAFTS
RELEASED PRESSURE
Unidirectional
External Return
Internal Return
Bidirectional
REMOTE SUPPLY PRESSURE
Simplified
Complete
Internal Supply Pressure
Hydraulic Pneumatic Energy Triangles
COMBINATION CONTROLS LINES
Solenoid
Solenoid or Manual
Solenoid and Pilot
Solenoid and Pilot or Manual
Servo
Thermal
Detent
Crossing
MANUAL CONTROL
Push-pull Lever
Manual Shutoff
General Manual
MEASUREMENT
Joining
Pressure
Temperature
Flow
FLUID STORAGE RESERVOIRS
Push Button
Pedal
Spring
Vent Vented ed
Pres Pressu suri rize zed d
Retu Return rn Abov Above e Flui Fluid d Leve Levell
Retu Return rn Belo Below w Flui Fluid d Leve Levell
ELECTRICAL SYMBOLS
HYDRAULIC SYMBOLS - ELECTRICAL
M
G
T
Transducer (Fluid)
Transducer (Gas / Air)
Generator
Electric Motor
Pressure Switch
Pressure Switch (Adjustable)
Temperature Switch
Electrical Wire
Pressure Switch
Temperature Switch
BASIC ELECTRICAL COMPONENT SYMBOLS Fuse: A component in an electrical circuit that will open the circuit if too much current flows through it.
Level Switch
Flow Switch
Circuit Breaker
HARNESS AND WIRE SYMBOLS Wire, Cable, or Harness Assembly Identification: Includes Harness Identification Letters and Harness Connector Serialization Codes (see sample).
Switch (Normally Open): A switch that will close at a specified point (temp, press, etc.). The circle indicates that the component has screw terminals and a wire can be disconnected from it. Switch (Normally Closed): A switch that will open at a specified specified point (temp, press, etc.). No circle indicates that the wire cannot be disconnected from the component.
1
Part Number: for Number: for Connector Plug
2
Ground (Wired): This indicates that the component is connected to a grounded wire. The grounded wire is fastened to the machine. Plug
Ground (Case): This indicates that the component component does not have a wire connected to ground. It is grounded by being fastened to the machine. Reed Switch: A Switch: A switch whose contacts are controlled controlled by a magnet. A magnet closes the contacts of
L-C12 3E-5179
AG-C4 111-7898
Receptacle Pin or Socket Number
Harness Identification Letter(s): (A, B, C, AA, AB, AC, ...) Harness Connector Serialization Code: The Code: The "C" stands for "Connector" and the number indicates which connector connector in the
FRONT VIEW VIEW ALL CALLOUTS
COOLANT TEMP SENSOR OIL PRESSURE SHUTDOWN
ENGINE OIL PRESS SENSOR
FUEL PRESS POST FILTER
FUEL TEMP SENSOR
A-C20
OIL TEMPERATURE SENSOR
*SOME COMPONENTS REMOVED FOR CLARITY
START AIR PRESSURE
LEFT SIDE VIEW VIEW ALL CALLOUTS
COOLANT LEVEL
COOLANT WATER
SENSOR
ECM
PRESSURE
AFTERCOOLER
A-C23 TO AIR TEMP SENSOR
INTAKE
CAM SPEED TIMING
A-C19
MANIFOLD
CONNECTS TO
AIR TEMP
INTAKE MANIFOLD AIR PRESS SENSOR SENSOR
SENSOR
ARC SUPPRESSOR
SERVICE TOOL
A-C18
CONNECTOR
A-C17 A-C2
A
A-C16
VIEW OF AREA “A” (ROTATED FOR CLARITY)
E-C2
L-C2
CDVR GEN TERMINAL STRIP
FUSE BLOCK CRANK SPEED
RESISTOR
STARTER SUPPRESSOR
ENGINE OIL
TERMINATING
AIR
TIMING
AIR START START
GROUND
SPEED SENSOR
LEVEL SWITCH 3-WAY *SOME COMPONENTS REMOVED FOR CLARITY