CAMD Assembly

Bench Vice Assembly

1

Bench Vice Assembly In this project, you will create the Bench Vice assembly. Figures B through E shows the views and dimensions of the components of the Bench Vice assembly.

Figure Figure 1 The Bench Vice assembly

Figure 2 Views and dimensions of the base

CAMD_ProE_Assembly

1

MIT College of Engineering, Pune - 411038.

2

Student Project

Figure Figure 3 Views and dimensions of the Vice Vice Jaw

Vice assembly Figure Figure 4 Views and dimensions of various components of the Bench Vice CAMD_ProE_Assembly

2


2

Student Project

Figure Figure 3 Views and dimensions of the Vice Vice Jaw

Vice assembly Figure Figure 4 Views and dimensions of various components of the Bench Vice CAMD_ProE_Assembly

2


Bench Vice Assembly

3

components of the Bench Vice Vice assembly Figures 5 Views and dimensions of various components

CAMD_ProE_Assembly

3


Butterfly Valve Assembly

1

Butterfly Valve Assembly Create the components of the Butterfly Valve Valve assembly and then assemble them, as shown in Figure 1. The dimensions of the components are shown in Figures 2 through 7. Assume the missing dimensions.

Figure Figure 1 The Butterfly Valve assembly

Figure Figure 2 Dimensions of the Body CAMD_ProE_Assembly

4


2

Student Project

Figure 4 Dimensions of the Retainer

Figure 3 Dimensions of the Shaft

Figure 6 Sectional front view of the Arm

Figure 5 Top view of the Arm

Figure 7 Dimensions of the Plate, Nut, and Screw

CAMD_ProE_Assembly

5


V-Block Assembly

1

V-Block Assembly Create all the components of the V-Block assembly and then assemble them, as shown in Figure 1. The dimensions of the components are shown in Figures 2 and 2.

Figure 1 The V-Block assembly

Figure 2 Views and dimensions of the V-Block body CAMD_ProE_Assembly

6


2

Student Project

Figure 3 Views and dimensions of the U-Clamp and Fastener

CAMD_ProE_Assembly

7


Crosshead Assembly

1

Crosshead Assembly In this project, you will create all components of the Crosshead assembly and then assemble them, as shown in Figure 1. Also you will create an exploded state, shown in Figure 2. The dimensions of the components are shown in Figures 3 through 7.

Figure 1 The Crosshead assembly

Figure 2 The exploded state of Crosshead assembly

CAMD_ProE_Assembly

8


2

Student Project

Figure 3 Front view and the right-side view of the Body

Figure 4 Dimensions of Keep Plate

Figure 5 Dimensions of Piston Rod

Figure 6 Dimensions of the Brasses and Bolt CAMD_ProE_Assembly

9


Crosshead Assembly

3

Figure 7 Dimensions of Nut

CAMD_ProE_Assembly

10


Double Bearing Assembly

1

Double Bearing Assembly In this project, you will create the Double Bearing assembly shown in Figure 1. The exploded state of the assembly is shown in Figure 2 and the dimensions of the components of the Double Bearing assembly are shown in Figures 3 through 7.

Figure 1 The completed Double Bearing assembly

Figure 2 The exploded view of the Double Bearing assembly

Figure 3 Top view of the Base

Figure 4 Top view of the Cap

Figure 5 Front view of the Base

Figure 6 Front view of the Cap

CAMD_ProE_Assembly

11


2

Student Project

Figure 7 Dimensions and drawing views of the Bushing and the Bolt

CAMD_ProE_Assembly

12


Fixture Assembly

1

Fixture Assembly Create all the components of the Fixture assembly and then assemble them, as shown in Figure 1. The details of the components of the Fixture assembly are shown in Figures 2 through 5.

Figure 1 The Fixture assembly

Figure 2 Dimensions of the End Plate

CAMD_ProE_Assembly

13


2

Student Project

Figure 3 Dimensions of the Disk

Figure 4 Dimensions of the Support Pin and the Bolt

CAMD_ProE_Assembly

14


Fixture Assembly

3

Figure 5 Dimensions of the Spacer, Center Pin, and the Nut

CAMD_ProE_Assembly

15


Plummer Block Assembly

1

Plummer Block Assembly In this project, you will create the components of the Plummer Block assembly, as shown in Figure 1 and then assemble them. The dimensions of the components are given in Figures 2 through 4.

Figure 1 The Plummer Block assembly

Figure 2 Views and dimensions of the Casting

CAMD_ProE_Assembly

16


2

Student Project

Figure 3 Views and dimensions of the Cap

Figure 4 Views and dimensions of Brasses, Nut, Lock Nut, and Bolt CAMD_ProE_Assembly

17


Press Tool Assembly

1

Press Tool Assembly In this project, you will create the Press Tool assembly shown in Figure 1. The exploded state of the assembly is shown in Figure 2 and the dimensions of the components of the Press Tool assembly are shown in Figures 2 through 5.

Figure 1 The completed Press Tool assembly after assembling the Top Plate with the assembly

Figure 2 The exploded view of the Press Tool as sembly

CAMD_ProE_Assembly

18

Figure 3 Figure showing the Bottom Plate


2

Student Project

Figure 4 Dimensions and views of the Top Plate

Figure 5 Dimensions and views of the Guide Pillar and Guide Bush

CAMD_ProE_Assembly

19


Pulley Support Assembly

1

Pulley Support Assembly Create the components of the Pulley Support assembly and then assemble them, as shown in Figure 1. After creating the assembly, create its exploded view, as shown in Figure 2. The dimensions of the components are given in Figures 4 through 8.

Figure 1 The Pulley Support assembly

Figure 2 Exploded view of the Pulley Support assembly CAMD_ProE_Assembly

20


2

Student Project

Figure 4 Dimensions of the Pulley

Figure 5 Dimensions of the Bushing

Figure 6 Left-side view of the Bracket

Figure 7 Sectioned front view of the

Figure 8 Dimensions of the Washer, Cap Screw, Turn Screw, and Nut CAMD_ProE_Assembly

21


Pulley Support Assembly

3

Figure 3 Parts list for the Pulley Support assembly

CAMD_ProE_Assembly

22


Shock Assembly

1

Shock Assembly In this project, you will create all components of the Shock assembly and then assemble them, as shown in Figure 1. Also create an exploded state of the assembly, as shown in Figure 2. The dimensions of the components are shown in Figures 3 through 10.

Figure 1 The Shock assembly

Figure 2 The exploded state of the Shock Assembly

CAMD_ProE_Assembly

23


2

Student Project

Figure 4 Dimensions for Pivot

Figure 3 Dimensions for Bracket

Figure 5 Dimensions for U-Support

CAMD_ProE_Assembly

24


Shock Assembly

3

Figure 6 Dimensions for Bushing

Figure 7 Dimensions for Self-locking nut

Figure 9 Dimensions for Hexagonal bolt

Figure 8 Dimensions for Washer

Figure 10 Dimensions for Castle nut

CAMD_ProE_Assembly

25


Wheel Support Assembly

1

Wheel Support Assembly Create all the components of the Wheel Support assembly and then assemble them, as shown in Figure 1. The dimensions of the components are shown in Figures 2 through 6.

Figure 1 The Wheel Support assembly

Figure 2 Dimensions of the Base

Figure 9-3 Dimensions of the Support

Figure 4 Front view of the Wheel

Figure 5 Sectioned side view of the Wheel

CAMD_ProE_Assembly

26


2

Student Project

Figure 6 Dimensions of the Shoulder Screw, Bolt, Nut, Bushing, and Washer

CAMD_ProE_Assembly

27


Pipe Vice Assembly

1

Pipe Vice Assembly In this Project, you will create all components of the Pipe Vice assembly, as shown in Figure 1, and then assemble them. The dimensions of the components are given in Figures 2 and 3.

Figure 1 The Pipe Vice assembly

Figure 2 Views and dimensions of the Base

CAMD_ProE_Assembly

28


2

Student Project

Figure 3 Views and dimensions of the Screw, Handle, Movable Jaw, and Handle Screw

CAMD_ProE_Assembly

29


Shaper Tool Head Assembly

1

Shaper Tool Head Assembly Create the Shaper Tool Head assembly, as shown in Figure 1. After creating the assembly, create its exploded view, as shown in Figure 2. The dimensions of the components are given in Figures 3 through 7.

Figure 1 The Shaper Tool Head assembly

Figure 2 The exploded view of the Shaper Tool Head assembly

CAMD_ProE_Assembly

30


2

Student Project

Figure 3 Views and dimensions of the Swivel Plate

CAMD_ProE_Assembly

31



3

Figure 4 Views and dimensions of the Back Plate CAMD_ProE_Assembly

32


4

Student Project

Figure 5 Views and dimensions of the Vertical Slide

CAMD_ProE_Assembly

33



5

Figure 6 Views and dimensions of various components

CAMD_ProE_Assembly

34


Stock Bracket Assembly

1

Stock Bracket Assembly In this project, you will create the Stock Bracket assembly shown in Figure 1. The details of the components of the Stock Bracket assembly are shown in Figures 2 through 8.

Figure 1 The Stock Bracket assembly

Figure 2 Top and front views of the Stock Support Base CAMD_ProE_Assembly

35


2

Student Project

Figure 3 Front and right-side views of the Stock Figure 4 Top and front views of the Adjusting Screw Support Roller Nut

Figure 5 Front and right-side views of the Support Roller Bracket

Figure 6 Views of the Adjusting Nut Handle and Adjusting Screw Guide CAMD_ProE_Assembly

36


Stock Bracket Assembly

3

Figure 7 Views of the Support Adjusting Screw

CAMD_ProE_Assembly

Figure 8 Top and front views of the Thrust Bearing

37


Motor Blower Assembly

1

Motor Blower Assembly In this project, you will create the Motor Blower assembly shown in Figure 1. The exploded view of the assembly is shown in Figure 2. The details of the components of the Motor Blower assembly are shown in Figures 3 through 8.

Figure 1 Motor Blower assembly

Figure 2 Exploded view of the Motor Blower assembly

CAMD_ProE_Assembly

38


2

Student Project

Figure 3 Dimensions of the Upper Housing

Figure 4 Dimensions of the Lower Housing CAMD_ProE_Assembly

39


Motor Blower Assembly

3

Figure 5 Dimensions of the Blower

Figure 6 Dimensions of the Motor

CAMD_ProE_Assembly

40


4

Student Project

Figure 7 Dimensions of the Cover

Figure 8 Dimensions of the Shaft

CAMD_ProE_Assembly

41


Radial Engine Assembly

1

Radial Engine Assembly In this project, you will create the Radial Engine assembly shown in Figures 1 and 2. The Radial Engine assembly will be created in two parts, one will be the subassembly and the other will be the main assembly. The dimensions of the components of the Radial Engine assembly are shown in Figures 3 through 6.

Figure 1 The Radial Engine assembly

Figure 2 The exploded view of the assembly

Figure 3 Views and dimensions of the Piston

CAMD_ProE_Assembly

42


2

Student Project

Figure 4 Views and dimensions of the Articulated Rod

Figure 5 Views and dimensions of the Master Rod

CAMD_ProE_Assembly

43


CAMD Assembly

Recommend Documents