C5 Config BSI

INFO’ DIAG DIAGNOSTIC TOOLS

CITROËN

LEXIA PROXIA CD 41

CITROËN SELLING DEALERS:

AFTER SALES DIVISION

-

PDI technicians

-

Campaign co-ordinators

N° 421

AUTHORISED REPAIRERS: -

Service Managers

19/12/2008

- Consultant technicians THE CONTENTS OF THIS BULLETIN SHOULD BE MADE KNOWN TO ALL PERSONNEL WHO, DIRECTLY OR INDIRECTLY, USE LEXIA / PROXIA DIAGNOSTIC TOOLS.

TITLE: Manual configuration of the BSI ECU on CITROËN C5 (X7).

CONCERNING: The operations for configuring a BSI ECU: •

Following the replacement of an ECU,

•

Following the downloading of an ECU,

•

Checking the configuration.

IMPORTANT: Incorrect configuration will affect the operation of the vehicle. Follow the internet configuration procedure described in this document and limit the use of manual configuration just to the cases quoted in the INFO'DIAG.

Page 1 / 31

CONTENTS

1

Introduction………………………………….....………………………………………..3

2

Preliminaries………………………………………...……………………………………3 2.1 Safety advice………………………………………………………………………….3 2.2 Technical advice……….…..………………………………………………………..3

3 Operations to be carried out…………........………….….......………………………....4 3.1

Operations to be carried out before removal, downloading or

configuration of the BSI……………………………………........................................5

4

3.2

Operations to be carried out to configure the BSI…………………………..6

3.3

Operations to be carried out after the configuration of the BSI…………8

Checking of configuration……………………………………………………………..9 4.1

Notes on the configuration tables…………………………………....………..10

4.2

Configuration menus…………………………………………………………….10

4.3

Customer options…………………….…………………………………………..11

4.4

Configuration……………………….……………………………………………..12

4.5

ECUs present………………………………….………………………………….29

4.6

« VIN code » menu………………………………………………………………31

Page 2 / 31

1

INTRODUCTION Configuration is a sensitive operation, which has direct consequences on the correct operation of the vehicle. Incorrect configuration can have an impact on: •

Safety (deactivation of vehicle protection devices),

•

Overall functioning of the vehicle (complete loss of or damage to vehicle functions)

•

Vehicle diagnostics (returning of fault codes which may cause the diagnostic tool methods to fail, and lead to the unjustified removal of parts).

You are therefore requested to perform the configuration operation following the instructions on this INFO’DIAG in order to ensure customer satisfaction by returning their vehicle in a perfect operational state.

2

PRELIMINARIES The instructions below must be followed to guarantee safety linked to vehicle operation and well-being.

2.1 Safety advice Before starting the engine: •

Check that the electronic parking brake is activated,

•

If the gearbox is automatic, check that the gear lever is in position «P » (Park),

•

If the gearbox is manual, check that the gear lever is in neutral.

2.2 Technical advice The BSI must be correctly configured before initialising the BSI, initialising the keys or starting the engine.

Page 3 / 31

3

OPERATIONS TO BE CARRIED OUT This chapter describes the steps to be followed to configure a BSI. •

If the configuration is being carried out following the replacement of a BSI, or following the downloading of the BSI: follow chapters 3.1, 3.2 and 3.3.

•

If the configuration is being carried out independently of a BSI replacement, or the downloading of a BSI (checking the correct configuration of a vehicle for example): follow chapters 3.1 and 3.2 only. Chapter 3.1

Operation to be carried out before removal, downloading or configuration of the BSI: Printing of customer options configuration values È Chapter 3.2 Operations to be carried out to configure the BSI: È A) Configuration by internet È B) Choice of maintenance plan È C) Manual configuration of customer options È D) Checking of certain parameters with manual configuration È Chapter 3.3 Operations to be carried out after the configuration of the BSI: Initialisation of BSI (or initialisation of keys or synchronisation of high frequency remote controls)

Page 4 / 31

3.1 Operations to be carried out before removal, downloading or configuration of BSI Before removing the faulty BSI ECU, or downloading or configuring the ECU, establish communication with this ECU on the vehicle using the LEXIA or PROXIA diagnostic tool. Print the screen « Customer Options » from the diagnostic tool, showing the configuration parameter values (or note these values down manually). To do so, carry out the following operations: LEXIA or PROXIA 1

Connect the diagnostic tool on the vehicle.

2

Select "Diagnosis"

3

Enter the vehicle details, then its RPO number

4

Start the "Global Test"

5

Select the menu « BSI », then validate using key « * ».

6

Select the item « Configuration ».

7

Select the item « Manual configuration ».

8

Select the menu « CUSTOMER OPTIONS ».

9

Print the diagnostic tool screen showing the configuration parameter values, or note down these values by hand

10

Return to the Global Test by successive presses on the « Return » key.

Once this operation has been completed, you may replace or download the BSI, if required to do so.

Page 5 / 31

3.2 Operations to be carried out to configure the BSI A) Configuration by internet LEXIA

PROXIA

11

Select the menu « BSI », then validate using key « * ».

12


13

Select the item « Configuration by internet ».

14

Once the configuration parameters screen has appeared, validate using key « * ».

15

The list of configuration menus appears. Validate using key « F5 » to launch configuration by internet.

Check the accuracy of the vehicle’s VIN, then validate using key « * ».

To allow an internet connection, make the connections indicated on Once the tool has received the configuration data, return 16 the diagnostic tool then validate to the Proxia tool by validating with the « return » key. using key « * » to start configuration by internet. Successively select the menus: - « CONFIGURATION », - « ECUs PRESENT », - « VIN code ».

17

The list of configuration parameters appears. Validate using the key « * »

In the « CONFIGURATION » menu, select the submenus: - « Vehicle definition – Equipment – Driving information », - « Air conditioning – Cabin heating», - « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser – Alarm », - « Fuel gauge law – Oil level gauge law ». In each sub-menu and in the ECUs present menu, validate using the « F5 » key to configure the parameters returned by the tool.

18

Return to the main menu of the BSI (« identification », « fault reading », etc.) with successive presses on the « return » key.

NOTE: If the configuration by internet does not work (presence of a message on the tool showing the error code linked to the phrase « it is pointless to repeat the operation »), carry out a manual configuration by replacing the internet configuration (based on the configuration tables in chapter 0), before continuing with the INFO’DIAG procedure from section B). NOTE: A monitoring of configuration failures is carried out centrally to correct any configuration malfunctions by internet. Page 6 / 31

B) Choice of maintenance plan LEXIA

PROXIA

19

Select the item « Maintenance – Operational Switch on the ignition. Select the item mode of BSI », « Maintenance – Operational mode of BSI », then validate with key « * ». then validate with key « * ».

20

Select the item « Maintenance », then validate with key « * ».

21

Select the item « Choice of maintenance plan (new vehicle preparation) ».

22

Follow the instructions given by the diagnostic tool: reply to the questions asked by the diagnostic tool.

23

Once the choice of maintenance plan procedure has been carried out, return to the main menu of the BSI (« identification », « fault reading »…) with successive presses on the « return » key.

C) Manual configuration of customer options Manually configure the «customer options » parameters, using the print-outs or notes previously made (chapter 3.1). LEXIA or PROXIA 24


25

Select the item « Manual configuration ».

26

Select the « CUSTOMER OPTIONS » menu.

27

Check (and modify if necessary), the values of each parameter, according to the values on the print-outs or notes.

28


D) Checking of certain parameters with manual configuration It is necessary to check certain configuration parameters (since the central base providing vehicle data may not be completely up to date). The parameters to check manually are shaded in grey in chapter 4. LEXIA or PROXIA Successively select the « CONFIGURATION », « ECUs PRESENT », and « VIN code » menus. In the « CONFIGURATION » menu select the sub-menus: - « Vehicle definition – Equipment – Driving information »,

29 - « Air conditioning – Cabin heating»,

- « Lighting – Signalling – Visibility – Rear view mirrors », - « Locking – Doors and tailgate – Immobiliser – Alarm », - « Fuel gauge law – Oil level gauge law ».

30

In each sub-menu and in the « ECUs present » and « VIN code » menus, check (and modify if necessary), the parameter values shaded in grey in the configuration tables (see chapter 4)

31

Return to the Global Test with successive presses on the « Return » key. Page 7 / 31

3.3 Operations to be carried out after the configuration of the BSI Operations to be carried out only if replacing or downloading a BSI: •

If the BSI has been replaced: initialise the new BSI ECU on the vehicle (« BSI initialisation »).

•

If the BSI has been downloaded, initialise the BSI ECU (« BSI initialisation »), or the keys, or simply synchronise the high frequency remote controls, depending on what is indicated in the procedure accompanying the recall campaign.

To carry out the initialisation operations, ALL of the customer’s keys and the confidential code card are required. LEXIA

PROXIA

32

Select the item « BSI », then validate using key « * ».

33

Select the item « Initialisation ».

34

Select the « BSI Initialisation » menu (or « Initialisation of keys »).

Select the « BSI Initialisation » menu (or « Initialisation of keys »).

35

Validate using key « * ».

36

Follow the instructions given by the diagnostic tool screens, in particular those displayed in the band at the bottom of the screen.

37


Once steps n° 32 to n° 37 have been completed, carry out the following operations to check that the vehicle is able to start. LEXIA

PROXIA

38

Select the item « BSI », then validate using key « * ».

39

Select the « Parameter Measures » menu of the BSI.

40

Select the sub-menu « Immobiliser ».

Select the item « pre-defined parameter screens », then select the sub-menu « Immobiliser ».

41

Check that the parameter « BSI matched to engine ECU » has the value « Yes ».

42

Check that the parameter « Engine ECU locked » has the value « No ».

43

Check that the parameter « Number of keys initialised » has the value « xx », where « xx » corresponds to the total number of the customer’s vehicle keys.

44

For each key, check that the parameter « Transponder label recognised » has the value « Yes ».

45

Return to the main menus screen of the tool (« diagnosis », « downloading», etc.) with successive presses on the « return » key. The diagnostic tool may be disconnected.

Page 8 / 31

4

CHECKING OF THE CONFIGURATION 4.1 Notes on the configuration tables The display of configuration parameters is conditional on their being present in the BSI software. The parameters will be displayed by the diagnostic tool partially or totally depending on the BSI software version. An underlined configuration value corresponds to the value to be programmed on all the vehicles.

Configuration notes: (1): Means that you have to programme the parameter according to the absence or presence of the option or to the vehicle definition. If the option or the vehicle definition is easily identifiable, the instruction is not accompanied by any particular text. (2): Means that you have to programme the value indicated in the column « Value to be configured ». This value is valid for all vehicles. It is prohibited to programme any other value. (3): Means that this parameter is programmed automatically when you use the procedure « CHOICE OF MAINTENANCE Plan (PRE-DELIVERY INSPECTION) »

Page 9 / 31

4.2

Configuration menus

After you have selected the menu « Manual configuration », the following menus are available: Menus

Pages

Customer options

11

Configuration

12

ECUs present

29

VIN code

31

NOTE: The parameters of the « Customer options » menu are also present in the configuration menu, it is therefore not necessary to configure these if the configuration of the parameters of the « Configuration » menu have been or will be carried out.

Page 10 / 31

4.3 Customer Options Configuration parameter

Multiplexed folding electric rear view mirrors Presence of rear screen wiping in reverse gear Type of deflation detection

Type of daytime-running lamps

Detection of driver's seat belt not fastened

Values to be configured No Yes Absent Present Absent Direct without display of pressures No daytime-running lamps Dedicated daytimerunning lamps

Comments Driver's door control pad with screenprinted . button Driver's door control pad with screenprinted button

.

Configure Present if a rear wiper is fitted. With rubber wheel valves. With metallic wheel valves. (1)

No

Value not to be configured except on the express request of the customer (deactivation of the alert for detection of driver’s seat belt not fastened).

Yes

(2)

No

For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Yes

For all vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

No

For all vehicles with the exception of vehicles destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Yes


Lighting by default of daytimerunning lamps

Simultaneous lighting of daytimerunning lamps and sidelamps

Page 11 / 31

4.4 Configuration Once the « Configuration » menu is selected, the following screen appears. Menus A

Contents VEHICLE DEFINITION – EQUIPMENT – DRIVER’S INFORMATION

Pages 13

B

AIR CONDITIONING – CABIN HEATING

20

C

LIGHTING – SIGNALLING – VISIBILITY – REAR VIEW MIRRORS

23

D

LOCKING – DOORS AND TAILGATE – IMMOBILISER – ALARM

26

E

FUEL GAUGE LAW - OIL GAUGE LAW

28

The content of each Menu is listed in the following chapters.

Page 12 / 31

4.4.1 Menu: vehicle definition – equipment – driving information (menu A) Configuration parameter (A)

Value to be configured

Comments All countries other than:

Overspeed alert for the Arabian peninsula

Absent

Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar. Countries Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.

Present Passenger’s seat position memorisation control unit option Automatic gearbox option Right-hand-drive vehicle Variable damping suspension option

Absent Absent Present No Yes Absent Present

(2)

(1) (1) Configure « present » for vehicles fitted with hydropneumatic suspension with 3.0L petrol (XFV) or 2.7 L diesel (UHZ) engine. For engines:

Absent Engine oil temperature sensor option

1.8 L petrol (6FY),

•

2.0 L petrol (RFJ),

•

2.2 L diesel (4HP, 4HT).

For engines: Present

Absent Presence of the telematic unit (RT3/RT4)

•

Present

•

3.0 L petrol (XFV),

•

1.6 L diesel (9HZ),

•

2.0 L diesel (RHR),

•

2.7 L diesel (UHZ).

•

Without audio equipment,

•

RD4 radio/CD/MP3.

•

Telematic unit (RT4/RT5),

•

Telematic unit (NG4),

•

Radio navigation (RNEG).

Presence of water-indiesel-fuel sensor

Present

(1) The presence of the sensor for detecting water in the diesel fuel filter is visible thanks to the blue 3way connector on the diesel fuel filter.

Presence of air pump

Absent

(2)

Multifunction screen option

Present

(2)

Absent

Key: Parameter to be systematically checked after configuring by internet Page 13 / 31

Configuration parameter (A) Origin of the waterin-diesel-fuel information Driving position memorisation option Presence of a trailer relay unit (BSR) Presence and type of vehicle cruise control


Comments

Engine ECU

(2)

Absent

Driver's seat with manual adjustment.

Present

Driver's seat with electric adjustment and memory.

No Yes Cruise control and speed limiter

Depending on the presence of a towbar. (2) For engines:

Engine ECU Origin of the oil temperature information

No Yes Absent

Type of parking assistance

Parking assistance with visual information Parking assistance with sound information Type of deflation detection

1.8 L petrol (6FY),

•

2.0 L petrol (RFJ),

•


For engines: Engine Relay Unit

Presence of a parking assistance button

•

Rear Front and rear and available parking space No Yes No Yes Absent

•

3.0 L petrol (XFV),

•

1.6 L diesel (9HZ),

•

2.0 L diesel (RHR),

•

2.7 L diesel (UHZ).

Depending on the presence of the button (or the presence of sensors on the bumpers, front and rear) Without ultra-sonic sensors on the bumpers. With 4 ultra-sonic sensors on the rear bumper only. With 4 ultra-sonic sensors on the front and rear bumpers. Depending on the absence or presence of ultrasonic sensors on the rear bumper. Depending on the absence or presence of ultrasonic sensors on the rear bumper. With rubber wheel valves.

Direct without With metallic wheel valves. display of pressures

Type of detection of presence of fuel cap

No detection

If particle filter absent.

By the BSI

If particle filter present.

Piloting of the diesel

No particle filter

If particle filter absent.


Configuration parameter (A) fuel additive pump

Value to be configured Control by wire

Presence of available parking space warning lamp Total time before next maintenance

If particle filter present.

Standard

For vehicles except those fitted with a 2.0 L petrol (RHR) or 1.8 L petrol (6FY) engine.

Controlled

For vehicles fitted with a 2.0 L petrol (RHR) or 1.8 L petrol (6FY) engine.

Type of alternator Presence of available parking space button

Comments

No Yes No

(1)

(2) (3)

12 or 24 months

12 months for « severe » use of the vehicle. 24 months for « normal » use of the vehicle.

0 km

Configure 0 km for vehicles with an RPO number ≥ 11480 (14th April 2008) or for vehicles which have had their first service.

2500 km

Configure 2500 km for vehicles with an RPO number < 11480 and which have not had their first service.

Threshold for first service

Maintenance Speedometers in kilometres - CASE N°1 threshold (marketing) (3) For severe use and engines: 15 000 km

•

2.0 L petrol (RFJ),

•

1.6 L diesel (9HZ).

(3) For normal use and engines: •

2.0 L petrol (RFJ),

•

1.6 L diesel (9HZ).

For severe use and engines: 20 000 km

•

1.8 L petrol (6FY),

•

3.0 L petrol (XFV),

•

2.0 L diesel (RHR),

•

2.2 L diesel (4HP, 4HT),

•

2.7 L diesel (UHZ).


Configuration parameter (A)


Comments (3) For normal use and engines:

30 000 km

•

1.8 L petrol (6FY),

•

3.0 L petrol (XFV),

•

2.0 L diesel (RHR),

•


•

2.7 L diesel (UHZ).

Speedometers in miles - CASE N°2 (3) For severe use and engines: 16 000 km

•

2.0 L petrol (RFJ),

•

1.6 L diesel (9HZ).

(3) For normal use and engines: •

2.0 L petrol (RFJ),

•

1.6 L diesel (9HZ).

For severe use and engines: 20 000 km

•

1.8 L petrol (6FY),

•

3.0 L petrol (XFV),

•

2.0 L diesel (RHR),

•


•

2.7 L diesel (UHZ).

(3) For normal use and engines:

32 000 km

Duration before 1st service

00 months

(2)

Kilometre threshold for forcing of customer mode

250 km

(2)

Memorisation of faults

Authorised

Presence of an electric secondary brake Electrically adjustable rear seats

No Yes Absent

•

1.8 L petrol (6FY),

•

3.0 L petrol (XFV),

•

2.0 L diesel (RHR),

•


•

2.7 L diesel (UHZ).

(2) (3) (1) (2)




Presence of the welcome function for the driver

No

With manual adjustment of the height and reach of the steering wheel.

Yes

With electrical adjustment of the height and reach of the steering wheel.

Comments

For engines: Engine relay unit (BSM) Origin of the oil pressure information

Number of switches for non-fastening of seatbelts Sensor for detection of presence of a front passenger Detection of nonfastening of the driver's seatbelt

5

(2)

Absent

(2)

Yes

(2)

Detection of nonfastening of the front passenger’s seat belt

Yes

(2)

Presence of a red warning lamp for the Steering Assistance alert Presence of an orange warning lamp for the Steering Assistance alert Tolerance on value set for the cruise control / speed limiter Lane Departure Warning System option

3.0 L petrol (XFV),

•

1.6 L diesel (9HZ),

•

2.0 L diesel (RHR),

•

2.7 L diesel (UHZ).

For engines:

Engine ECU

Presence of a radio RD4

•

No Yes

•

1.8 L petrol (6FY),

•

2.0 L petrol (RFJ),

•


(1)

No

Mechanical power steering.

Yes

Hydraulic power steering.

Yes

(2)

3 km/h

(2)

Absent

(1) Depending on presence of a button for deactivation of the function.

Present



Value to be configured No

Presence of a fuel pump

Comments All diesel engines except: •

On engines: Yes

Presence of a boot relay unit

No

(2)

Type of vehicle

Saloon Estate

(1)

Presence of HeadUp display

No

(2)

Presence of a mobile deflector

No

(2)

Presence of HandsFree Kit Presence of CD changer

2.7 L diesel (UHZ).

No Yes Absent Present

•

Petrol,

•

2.7 L diesel (UHZ).

(1) (1)

Detection of nonfastening of middle rear passenger’s seat belt

Yes

(2)

Detection of nonfastening of rear LH passenger’s seatbelt

Yes

(2)

Detection of nonfastening of rear RH passenger’s seatbelt

Yes

(2)

No

(1) Depending on the presence of a bass box in the boot.

Presence of an audio equaliser amplifier Sound alert for parking assistance emitted by switch module under steering wheel

Yes No

With radio/CD/MP3/RD4 or telematic unit (RT4, RT5, NG4) or radio navigation (RNEG).

Yes

Without audio equipment.




Display of fuel consumption without overconsumption due to regeneration of the particle filter

No

Time of response by the engine ECU to the BSI during operation of cruise control Display of the rear seat belt fastening alert on opening of a rear door or switching on the ignition Retention of braking (by the ESP) for 2 seconds when starting on a gradient Battery charge estimation function Presence of massaging front seats Presence of a Built-in Hydraulic Interface (BHI)

(2)

0.6 s

•

All engines except 1.6 L Diesel (9HZ),

•

1.6L diesel (9HZ) engine and BSI software version ≥ 6.30.

•

1.6L diesel (9HZ) engine and BSI software version = 5.50.

1.2 s

Yes

(2)

No

Handbrake with warning lamp.

Yes

Electric secondary brake.

Present, performed by the Battery (2) charge status control unit No Yes

(1)

No

Metal suspension.

Yes

Hydropneumatic suspension

No

Presence of power steering

Yes

Presence of services module

No Yes

Presence of a navigation system (NG4) Presence of a radio RD4 Presence of HandsFree Kit

Comments

No Yes No Yes No Yes

With mechanical power steering. With hydraulic power steering, (presence of an electro-pump) (1) Configure « yes » if a telematic unit (NG4) with emergency call button is present. (1) (1) (1)




Presence of CD changer

No Yes

(1)

Presence of massaging front seats

No Yes

(1)

Comments

4.4.2 Menu: air conditioning – cabin heating (menu B) Configuration parameter (B) Presence of the pollution sensor Presence of humidity sensor in the cabin

Type of sunlight sensor

Value to be configured No

For Mono-zone Automatic Air Conditioning.

Yes

For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side).

No

(2)

Mono-zone sunlight sensor

Type of air mixing Bi-zone Mono-zone

Type of additional heating

For Mono-zone Automatic Air Conditioning.

For Bi-zone Automatic Air Conditioning (separate Bi-zone sunlight adjustment of the temperature and air distribution on the sensor left-hand side and right-hand side). Mono-zone

Type of air distribution

Comments

For Mono-zone Automatic Air Conditioning. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). For Mono-zone Automatic Air Conditioning.

Bi-zone

For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side).

Absent

For petrol engines.

Heating elements Autonomous burner

For a diesel engine without additional heating. For a diesel engine with additional heating.


Configuration parameter (B)

Value to be configured Programmable burner 1,19

Comments For a diesel engine with programmable additional heating. For engines: •

3 L petrol (engine plate XFV).

For engines: 1,24 Aircon compressor drive ratio

•

1.8 L petrol (engine plate 6FY),

•

2.0 L petrol (engine plate RFJ).

For engines: • 1.6 L diesel (engine plate 9HZ),

1.28

• 2.0 L diesel (engine plate RHR), • 2.2 L diesel (engine plate 4HP and 4HT).

1.34 Mono-zone Presence and type of blown air sensor Presence of electric sun blind

Bi-zone No

For engines: •

2.7 L diesel (engine plate UHZ).

For Mono-zone Automatic Air Conditioning. For Bi-zone Automatic Air Conditioning (separate adjustment of the temperature and air distribution on the left-hand side and right-hand side). (2)




Comments

Temperate (-17°C to +37°C)

For vehicles destined for the following countries, territories or departments: South Africa, Barbados, Belgium, Bermuda, Cyprus, Spain, Metropolitan France, United Kingdom, Greece, Grenada, Guadeloupe, Guyana, Ireland, Italy, Jamaica, Luxembourg, Malta, Martinique, Mauritius, New Caledonia, New Zealand, Netherlands, French Polynesia, Portugal, Reunion, St. Martin, St. Lucia, Seychelles, Tahiti, Trinidad & Tobago.

Cold (-25°C to +37°C)

For vehicles destined for the following countries: Albania, Germany, Austria, Azerbaijan, Bosnia, Bulgaria, Croatia, Denmark, Estonia, Hungary, Iceland, Latvia, Lithuania, Macedonia, Poland, Romania, SerbiaMontenegro, Slovakia, Slovenia, Switzerland, Czech Republic.

Very cold (-30°C to +37°C)

For vehicles destined for the following countries: Armenia, Belarus, Finland, Georgia, Kazakhstan, Kirghizistan, Moldavia, Norway, Uzbekistan, Russia, Sweden, Turkmenistan, Ukraine.

Hot (-17°C to +45°C)

For vehicles destined for the following countries: Algeria, Angola, Antigua & Barbuda, Argentina, Aruba, Australia, Bahamas, Bangladesh, Benin, Bolivia, Botswana, Brazil, Brunei , Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Sierra Leone, Chile, Colombia, Comoros, Congo, South Korea, Costa Rica, Ivory Coast, Cuba, Djibouti, Egypt, El Salvador, Ecuador, Ethiopia, Fiji, Gabon, Gambia, Ghana , Guatemala, Guinea, Haiti, Honduras, Hong Kong, India, Indonesia, Iraq, Iran, Israel, Japan, Jordan, Kenya, Laos, Lebanon, Liberia, Libya, Macao, Madagascar, Malaysia, Malawi, Mali, Morocco, Mauritania, Mayotte, Mexico , Mozambique, Namibia, Nicaragua, Niger, Nigeria, Uganda, Pakistan, Palestine, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Central African Republic, Dominican Republic, Rwanda, Senegal, Singapore, Somalia, Sudan, Sri Lanka, Surinam, Syria, Tajikistan, Taiwan, Tanzania, Chad, Thailand, Togo, Tonga, Tunisia, Turkey, Myanmar, Uruguay, Venezuela, Vietnam, Yemen, Zambia, Zimbabwe.

Very hot (-17°C to +50°C)

For vehicles destined for the following countries: Saudi Arabia, Bahrain, United Arab Emirates, Kuwait, Oman, Qatar.

Type of climate




Presence of heated seats

No Yes

Type of aircon pressure sensor

Pressure sensor 30 bars

Comments Depending on presence or absence of heated seat controls. (2)

4.4.3 Menu: lighting – signalling – visibility – rear view mirrors (menu C) Configuration parameter (C) Sunlight sensor option

Rain sensor option

Value to be configured Absent Present Absent Present

Comments Configure Present if the vehicle is fitted with a wipers stalk with « auto » position. Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.

Headlamp wash option

Absent Present

(1)

Automatic lighting of instrument panel and multifunction screen depending on external brightness

Absent

(2)

Automatic lighting of hazard warning lamps in the event of impact

Absent

(2)

Absent Present

Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.

Automatic lighting of hazard warning lamps under heavy deceleration

Present

(2)

Presence of front foglamps

No Yes

(1)

Guide-me-home lighting option


Configuration parameter (C)


Multiplexed folding electric rear view mirrors

No

Rear view mirrors indexed to reverse gear

Yes No Yes

Comments Driver's door control pad with screenprinted button . Driver's door control pad with screenprinted button . Depending on whether the rear view mirrors are equipped with electric folding or not.

Presence of rear screen wiping in reverse gear

Absent Present

Configure Present if a rear wiper is fitted.

Lighting of hazard warning lamps on pressing the emergency call button

Absent

(2)

Single filament halogen bulbs

(1)

Type of headlamps

Discharge bulbs

Type of daytimerunning lamps

Presence of a rain and sunlight sensor with wipers with regulated speed Presence of a lighting stalk with four positions Presence of a stalk with one-touch activation of automatic wipe

No daytimerunning lamps Dedicated daytimerunning lamps

(1)

No Yes

Configure Present if the vehicle is fitted with a wipers stalk with « auto » position.

No Yes

(1)

No Yes

Configure yes if the vehicle is fitted with a wipers stalk with « auto » position.


Configuration parameter (C)


Activation of automatic lighting of headlamps via the personalisation menu

No

Presence of a third button on the high frequency remote control for switching on the lights

Lighting of daytimerunning lamps by default

Simultaneous lighting of daytime-running lamps and sidelamps

Comments

(2)

No Configure « No » for vehicles fitted with a motorised boot. Yes

No

For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Yes


No

For all vehicles except those destined for the Nordic countries (Netherlands, Denmark, Sweden, Finland, Norway and Iceland)

Yes


Presence of parking lamps

No

(2)

Presence of headlamp height correctors

No

(2) Configure this parameter to « No » even if the vehicle is fitted with headlamp height correctors

Presence of the light pack unit

No Yes

Configure yes if the vehicle is fitted with « light bars » under the fascia.

Type of bend lighting

Static lighting controlled by the BSI Dynamic lighting: directional headlamps

Presence of rear screen wiping in reverse gear

Absent Present

If the vehicle is fitted with halogen bulbs.

If the vehicle is fitted with discharge bulbs.

Configure Present if a rear wiper is fitted.


4.4.4 Menu: locking – doors and tailgate - immobiliser - alarm (menu D) Configuration parameter (D)


Opening of the boot using the high frequency remote control option

Absent

If standard tailgate.

Present

If motorised boot tailgate.

Deadlocking Type of locking Normal locking Number / type of sun roof Type of child lock Passenger door lock

Inviolability mode Anti-pinch function on windows and sun roof Presence of a multiplexed sun roof Opening of the rear screen using the high frequency remote control option Presence of electronically controlled fuel flap When actioning unlocking by high frequency remote control

With a locking control with Deadlocking (to check carry out a Deadlocking actuator test). With a locking control with normal locking (to check carry out a Deadlocking actuator test).

No sun roof 1 sun roof

(1)

blind Electric Mechanical Absent Present No alarm

Type of alarm

Comments

(1) Left-hand drive vehicle. Right-hand drive vehicle. Without ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)

Standard alarm

With ultra-sonic detectors (on the roof console or on the windscreen aperture pillars)

Alarm for Belgium

For vehicles destined for Belgium with ultra-sonic detectors (on the roof console or on the windscreen aperture pillars).

Active

(2) (3)

Present on all openers

(2)

Absent

(2)

No

(2)

Absent

(2)

Simultaneous unlocking of all of the Vehicle with normal unlocking. doors Unlocking of driver’s door only

Vehicle with deadlocking.


Configuration parameter (D)


Type of fitting of alarm

Factory fitted alarm

Type of motorised boot tailgate

Presence of specific high frequency receptor (Japan)

Comments (2)

No motorised boot tailgate (1) Multiplexed motorised boot tailgate Absent

(2)


4.4.5 Menu: fuel gauge law – oil gauge law (menu E) Configuration parameter (E) Type of fuel Tank capacity Gauge resistance for empty tank Gauge resistance for full tank Fuel gauge law - alert level Fuel gauge law selection of the vehicle

Oil gauge law – engines

Value to be configured Petrol Diesel

Comments (1)

71 litres

For petrol engines.

72 litres

For diesel engines.

330 ohms

For petrol engines.

332 ohms

For diesel engines.

58 ohms

(2)

7 litres

For diesel engines.

8 litres

For petrol engines.

9 litres

For petrol and alcohol engines.

Petrol vehicles Diesel vehicles Type of engine: XFV (3.0L petrol) Type of engine: 9HZ (1.6L diesel) Type of engine: RHR (2.0L diesel) Type of engine: 4HP, 4HT (2.2L diesel) Type of engine: UHZ (2.7L diesel) Type of engine: 6FY (1.8L petrol) Type of engine: RFJ (2.0L petrol)

(1)

(1)

For engines: Engine relay unit (BSM) Origin of the oil level information

•

3.0 L petrol (XFV),

•

1.6 L diesel (9HZ),

•

2.0 L diesel (RHR),

•

2.7 L diesel (UHZ).

For engines: Engine ECU

•

1.8 L petrol (6FY),

•

2.0 L petrol (RFJ),

•



4.5 ECUs present Value to be configured

Comments

Steering wheel with fixed central controls

Present

(2)

Airbag

Present

(2)

High frequency receptor

Absent

(2)

Engine relay unit (BSM)

Present

(2)

Rain / sunlight sensor

Absent Present

(1)

Driver's door module

Present

(2)

Built-In Systems Interface

Present

(2)

Alarm

Absent Present

Parking assistance

Absent Present

Instrument panel

Present

Calculator

Absent Audio equipment Present Lane wandering alert

Absent Present

NaviDrive telematic unit

Absent Present Absent

Display Present

Depending on presence of ultra-sonic sensors on the roof console or the windscreen aperture pillar. Depending on the absence or presence of 4 ultra-sonic sensors in the rear bumper. (2) Without radio type RD4. With a telematic unit (RT3, RT4 or NG4). With radio navigation (RNEG). With radio type RD4 (CD or CD/MP3). Depending on presence of a switch for activation of the function. Depending on presence of a NaviDrive telematic receiver (RT3 or RT4), of a telematic unit (NG4) or of radio navigation (RNEG). With telematic unit (RT3, RT4 or NG4) or with radio navigation (RNEG). Without telematic unit (RT3, RT4 or NG4) or with radio navigation (RNEG). Depending on the presence of a trailer relay unit (this equipment is necessary if the vehicle is fitted with a towbar).

Trailer relay unit

Absent Present

Air conditioning

Present

(2)

Driver’s seat memorisation control unit

Absent Present

(1)


Calculator CD changer

Hands-Free Kit


Comments

Absent Present

(1)

No Yes

Configure « Yes » for vehicles with an RD4 radio (or radio navigation (NG4) without service module) and hands-free kit. To check for the presence of a handsfree kit, press on the « Menu » button of the radio, note the presence of the following icon on the right of the multifunction screen.

Windscreen wipers

Present

(2)

Audio amplifier

Absent Present

(1)

Steering angle sensor

Present

(2)

Engine ECU

Present

(2)

Automatic gearbox / piloted manual gearbox

Absent Present

(1)

ABS / ESP ECU

Present

(2)

Absent

Vehicle with rubber wheel valves.

Present

Vehicles with metallic wheel valves.

Tyre under-inflation detection

Variable damping

Absent Present

Configure « present » for vehicles fitted with hydropneumatic suspension with 3.0L petrol (XFV) or 2.7 L diesel (UHZ) engine.

Suspension

Absent Present

Configure « present » for vehicles fitted with hydropneumatic suspension.

Electric parking brake

Absent Present

(1)

Absent

Vehicles with mechanical power steering.

Present

Vehicles with hydraulic power steering (presence of an electro-pump).

Power steering


Calculator


Comments

Absent

Vehicles with halogen headlamps.

Present

Vehicles with Xenon headlamps.

Present

(2)

Directional headlamps

Yaw / lateral acceleration sensor Additional heating Motorised boot unit

Absent Present Absent Present

(1) (1)

Seat belt not fastened warning lamp (TNB)

Present

(2)

Battery charge status unit

Present

(2)

4.6 Menu: «VIN code » Enter the vehicle’s VIN code (17 characters).


C5 Config BSI

Recommend Documents