Learning to understand P&ID for oil & gas industry.Full description
Full description
Two comparators of a quad OPAMP IC is used to form a window comparator for sensing low / high input voltage while their 'OR' logic wired output drives a relay to cut-off the load beyond a specified...Full description
Full description
Two comparators of a quad OPAMP IC is used to form a window comparator for sensing low / high input voltage while their 'OR' logic wired output drives a relay to cut-off the load beyond a specified...
test voltagesDescription complète
Full description
Basic Philippine Law on LibelFull description
this is a basic guide on learning the language ILOKANO.Full description
Full description
notesFull description
Full description
test voltagesDescripción completa
VOLTAGE TRANSFORMER
VOLTAGE TRANSFORMER
Definitions A device used to step down voltage from high value (primary voltage) to a low value (secondary voltage). Low value voltage is easy to measure, no need to develop high voltage measuring equipment. The secondary voltage is substantially proportional to the primary voltage and differs in phase from it by an angle which is approximately zero for an appropriate direction of the connections.
VOLTAGE TRANSFORMER
How Transformer Works When an electric current passes through a long, hollow coil of wire then there will be a strong magnetic field inside the coil and a weaker field outside it. The lines of the magnetic field pattern run through the coil, spread out from the end and go round the outside and in at the other end.
VOLTAGE TRANSFORMER
How Transformer Works
VOLTAGE TRANSFORMER
How Transformer Works With a hollow coil the lines form complete rings. If there is an iron core in the coil it becomes magnetised, and seems to make the field become much stronger while the current is on.
VOLTAGE TRANSFORMER
How Transformer Works The iron core of a transformer is normally a complete ring with two coils wound on it. One is connected to a source of electrical power and is called the 'primary coil'; the other supplies the power to a load and is called the 'secondary coil'. The magnetisation due to the current in the primary coil runs all the way round the ring. The primary and secondary coils can be wound anywhere on the ring, because the iron carries the changes in magnetisation from one coil to the other. There is no electrical connection between the two coils. However they are connected by the magnetic field in the iron core.
VOLTAGE TRANSFORMER
How Transformer Works When there is a steady current in the primary there is no effect in the secondary, but there is an effect in the secondary if the current in the primary is changing. A changing current in the primary induces an e.m.f. in the secondary. secondary. If the secondary is connected to a circuit then there is a current flow.
VOLTAGE TRANSFORMER
How Transformer Works
VOLTAGE TRANSFORMER
How Transformer Works The iron core is itself a crude secondary (like a coil of one turn) and changes of primary current induce little circular voltages in the core. Iron is a conductor and if the iron core were solid, the induced voltages would drive wasteful secondary currents in it (called 'eddy currents'). So the core is made of very thin sheets clamped together, with the face of each sheet coated to make it a poor conductor. The edges of the sheets can be seen by looking at the edges of a transformer core.
VOLTAGE TRANSFORMER
How Transformer Works
VOLTAGE TRANSFORMER
Function 1.
Protection Voltage transformer connected to protection equipment (protection relay). The protection relay can be set to identify whether the the input voltage (voltage transformer’s secondary voltage) indicate that fault occur in i n the system.
2.
Measurement Voltage transformer connected to measurement equipment (voltmeter, energy meter).
VOLTAGE TRANSFORMER
Construction Type Single Phase
VOLTAGE TRANSFORMER
Construction Type Single Phase
VOLTAGE TRANSFORMER
Construction Type Single Phase Two Winding
VOLTAGE TRANSFORMER
Construction Type Three Phase
VOLTAGE TRANSFORMER
Construction Type Three Phase
VOLTAGE TRANSFORMER
Construction Type Three Phase
VOLTAGE TRANSFORMER
Construction Type
VOLTAGE TRANSFORMER
Connection to Measurement or Protection Devices Measurement or protective devices are load to transformer.. The circuit connection shall be in parallel. transformer
the
voltage
Current transformer not connected to the load when installed to the switchgear shall be left open circuit. Open circuit is a condition when the voltage transformer is not connected to its load. Shorting the secondary terminal to ground during operation will damaged the voltage transformer (or burst). bu rst).
VOLTAGE TRANSFORMER
Connection of Voltage Transformer v
v
Single Line Transformer
Diagram
For
2
Winding
v
v
Single Line Diagram 3 Winding Transformer
VOLTAGE TRANSFORMER
Typical Voltage Transformer Connection
VOLTAGE TRANSFORMER
Typical Voltage Transformer Connection
VOLTAGE TRANSFORMER
Typical Voltage Transformer Connection
VOLTAGE TRANSFORMER
Typical Current Transformer Description 132kV/110V/110V A.C 3 3 3
-
Voltage Ratio
CL.: 0.2
-
Accuracy Class
100VA/Phase 100V A/Phase
-
Rated Burden
V.F .F.: .: 1.9, 30s
-
Voltage Factor
VOLTAGE TRANSFORMER
Term & Definitions Rated Primary Voltage The value of primary voltage which specified by manufacturer (shall be based on customer/purchaser requirements). E.g. 132kV, 275kV, 33kV etc. Rated Secondary Voltage The value of secondary voltage which specified by manufacturer or customer. E.g. 110V A.C. Rated Burden The burden assigned by manufacturer at which the voltage transformer performs with specified accuracy. Burden is a load connected across the secondary of voltage transformer expressed in VA.
VOLTAGE TRANSFORMER
Term & Definitions Accuracy Class The class assigned to the voltage transformer with the specified limits of ratio error and phase angle error error.. Accuracy Class: 5, 0.5, 0.2 For metering. Accuracy Class :3P, 5P For protection Rated Voltage Factor (V.F) The upper limit of operating voltage (primary voltage) where voltage transformer should be able to withstand during operation.
VOLTAGE TRANSFORMER
Term & Definitions Rated Voltage Factor Depending on the system in which the VT is to be used, the rated voltage factors to be specified are different. The table below is adopted from International standards.
VOLTAGE TRANSFORMER
Term & Definitions Turns Ratio The ratio between the number of actual turns of wire in each coil is the key in determining the type of transformer and what the output voltage will be. The ratio between output voltage and input voltage is the same as the ratio of the number of turns between the two windings. The relationship between the number of turns in the secondary and the number of turns in the primary is commonly called the Turn Ratio or Voltage Ratio.
VOLTAGE TRANSFORMER
Testing Polarity Check To prove that a V.Ts has been manufactured and installed with the correct polarity. Insulation Resistance Dielectric insulation tests such as power frequency withstand voltage test on primary and secondary windings for one minute and insulation resistance test.
VOLTAGE TRANSFORMER
Testing Accuracy Test & Ratio Test Injection from primary winding and measurement at the secondary winding (at the terminal). Gas Pressure Indication (GIS V.T) V.T) Gas pressure low 1st stage and 2nd stage indication to control room by reducing the gas pressure inside the V.T V.T compartment.
VOLTAGE TRANSFORMER
V.T Loading Lo ading Calculation 1)
Identi Ide ntify fy equ equipme ipment nt con connec nected ted to the vo volta ltage ge tran transfo sforme rmerr.
2)
Identify Identi fy the cab cable le loo loop p leng length th fro from m volt voltage age tra transf nsform ormer er terminal’s to the connected equipment.
3)
Calc Ca lcul ulat ate e all all th the e con conne nect cted ed lo load ad..
VOLTAGE TRANSFORMER
Typical Installation Inside The T he Gas Insulated Switchgear Sw itchgear
