AUTOMOTIVE ENGINE SERVICE TOOLS.pdf

QUICK FINDER INDEX AUTOMOTIVE ENGINE SERVICE TOOLS

T

&E OOLS

Engine Service Tools ................................................................................. Page No. 124 to 151

Page No. 134, 147 Page No. 124 to 131 Page No. 136 to 138 Page No. 135 Page No. 129 to 133 Page No. 132 Page No. 144 to 147 Page No. 140 to 143 Page No. 148, 149 Page No. 151 Page No. 139 Page No. 135 Page No. 130

Engine Fan Service Tools ........................................................................ Page No. 152 to 154

Viscous Fan Wrenches & Holders .............................................. Page No. 152 to 154 Fan Belt Tension Gauges & Service Tools ................................. Page No. 152 to 154 Serpentine Belt Service Tools ..................................................... Page No. 152, 153

Exhaust Service Tools ............................................................................... Page No. 155 to 157 Exhaust Back Pressure Testers & Fume Extractors ................ Page No. 156 Exhaust Pipe Re-shapers & Expanders..................................... Page No. 155, 157 Exhaust Pipe Cutters .................................................................. Page No. 157

Oil Filter Tools .............................................................................................. Page No. 158 to 163 Oil Filter Wrenches & Pliers ....................................................... Page No. 158 to 163 Oil Filter Crushers ....................................................................... Page No. 163

Radiator Service Tools .............................................................................. Page No. 164 to 171

Radiator Pressure Testers & Adaptors ...................................... Page No. 164 to 169 Radiator Coolant Testers ............................................................ Page No. 171 Radiator & Heater Service Tools ................................................ Page No. 169 to 171 Radiator Hose Pinch-Off Pliers .................................................. Page No. 171 Radiator Thermometers & Anti-Freeze Testers ......................... Page No. 170, 171

Carburettor Service Tools ........................................................................ Page No. 172 to 174

Carburettor Adjusting Tools ........................................................ Page No. 172 to 174 Carburettor Leak Detectors ......................................................... Page No. 174 Carburettor Synchronizer ........................................................... Page No. 174 Fuel System Service Tool Kits ..................................................... Page No. 174

Electronic Fuel Injection Tools................................................................ Page No. 175 to 182

Fuel Injection Testers .................................................................. Page No. 175 to 179, 181 Fuel Injection Cleaners ............................................................... Page No. 180, 181 Fuel Injection Adaptors ............................................................... Page No. 178, 179 Fuel Injection Noid & IAC Signal Light Testers ......................... Page No. 182

Diesel Engine Service Tools .................................................................... Page No. 183 to 188

TM

Automotive Engine Service Tools

Engine Cylinder Hones & Ball Hones ......................................... Valve Lifters & Valve Tools - General .......................................... Piston Ring Compressors & Piston Ring Service Tools ........... Ridge Reamers, Cylinder Liner Pullers ...................................... Hydraulic Tappet, Cylinder Head Service Tools & Gauges ...... Dowell Pullers, Torque Angle Gauges ........................................ Timing Chain & Camshaft Service Tools .................................... Harmonic Balancer & Crankshaft Service Tools ....................... Engine Sensor & Switch Sockets ............................................... Engine Lifting & Support Bars, Stands ...................................... Vacuum & Fuel Service Tools ..................................................... Welsh Plug Tools .......................................................................... Valve Seat Cutting Tools ..............................................................

Diesel Injector Sockets & Pullers ............................................... Page No. 183 to 186 Diesel Injector Nozzle Testers & Adaptors ................................ Page No. 188 Diesel Fuel Pump Timing Tools .................................................. Page No. 187 Diesel Cylinder Liner Height Guage .......................................... Page No. 188 Diesel Engine Test Gauges & Adaptors ..................................... Page No. 187 Diesel Glow Plug Pullers ............................................................ Page No. 188 Diesel Compression Gauges & Adaptors .................................. Page No. 214 to 219 See Test Gauge Section Work Safely With Hand Tools - Wear Safety Goggles 123

T

&E OOLS

ENGINE SERVICE TOOLS - VALVE LIFTERS Use with # 4418 or # 4419 Air Holds

No.4057 Deluxe OHV Spring Compressor Our best quality OHV spring compressor features: Heavy-duty construction, shorter overall length for use in confined spaces, removable handle for operation by socket wrench. Spring loaded. Length: 4.3/4"(120mm)

Use with # 4418 or # 4419 Air Holds

No.4078 Cam Action OHV Spring Compressor Cam action compressor removes valve springs on most OHV engines without removing the cylinder head. Tool maintains constant length as spring is compressed. Features extra slim-line construction. Fast, because there is no need to readjust the tool after compressing each spring. Length: 6"(150mm)


Using hexagon screw

No.4140 Overhead Valve Spring Compressor

Professional quality at an economical price. This compressor removes valve springs on most OHV engines without removing the cylinder head. Tool maintains constant length as spring is compressed. Features extra slim-line construction with T-handle. Length: 6"(150mm)

No.4120 Cam Action OHV Spring Compressor l

Use with #4418 or #4419 Air Holds

Makes compressing the spring and removing the keepers a simple job because there is no need to remove the head. Adjustable cam action. Fast, because there is no need to readjust the tool after each spring. Length: 8"(205mm)

No.2-7928 Ford Valve Spring Compressor

No.4129 Valve Spring Compressor l

Using cam lever

Use with #4418 or #4419 Air Holds

Makes compressing the valve spring and removing the keepers a simple job because there is no need to remove the head. Multi hole adjustments on handle, bar and jaws enables an unlimited combination of settings. Hook engages under rocker arm, cam or rocker studs. Length: 12.1/2"(317mm)


You don’t have to remove the head from the engine, it is easier & quicker for valve spring, valve seal, camshaft & retainer service. You can use a 3/8”Drive ratchet or breaker bar to work on 1991 & newer Ford 4.6 Litre 2 valve V-8 engines also 1997 and newer Explorers with 4.0 Litre engines. Length: 7.1/2"(190mm)

Air Fitting for Holding Valves in Place

No.4132 Twin OHC Valve Lifter

New design with centrally locating stem which passes down into spark plug orifice and screws into plug hole thread. Dual function centre pivot stem also serves as an air-hold complete with quick coupler nipple. Furnished with 3 recessed open sided valve spring compressor adaptors: Small Size: 5/8" to 15/16" (16mm to 24mm) Medium Size: 3/4" to 1" (19mm to 25mm) Large Size: 15/16" to 1.13/16" (24mm to 30mm) Includes three different sizes of centre bushings for stem location. Supplied in blow mold case. Length: 8"(205mm)

124

TM

No.4128 Heavy-Duty Car & Motorcycle Valve Lifter l

Suitable for Overhead Cam Engines

Five valve adaptors enable use in restricted and confined spaces with clearance to easily remove valve collets. Adaptor Sizes: 16, 19, 23, 25 and 30mm Forged body for extra strength. Capacity Depth: 220mm Throat Depth: 120mm

Work Safely With Hand Tools - Wear Safety Goggles

ENGINE SERVICE TOOLS - VALVE LIFTERS No.4116 C-Type Valve Lifter

No.4125 Economy Valve Lifter

Light weight C-type lifter works as a one hand tool. Both lifting and releasing of the spring can be done with one hand leaving the other hand free to handle the valve spring keepers. Ratchet locks automatically at any position. This lifter will handle most cars and light trucks. Frame is cold rolled steel with hardened jaws. Set includes #4116-1 Straight and #4116-2 Offset jaws. Maximum Opening: 7"(180mm) Maximum Depth: 7"(180mm) No.4116-1 Replacement Straight Jaw Set to Suit #4116 No.4116-2 Replacement Offset Jaw Set to Suit #4116

Designed for overhead valve engines. Features a rack and pinion mechanism. Compact, rugged, powerful and is simple and fast to use. Two sets of jaws included: #4126 Straight Valve Lifter Jaws #4127 Offset Valve Lifter Jaws Maximum Opening: 7"(180mm) Maximum Depth: 5"(125mm) No.4126 No.4127

T

&E OOLS

Straight Jaw Set To Suit #4125 Valve Lifter Offset Jaw Set To Suit #4125 Valve Lifter

Opening Max: 8"(200mm) Depth Max: 10"(250mm)

Opening Max: 6.7/8"(175mm) Depth Max: 6.1/2"(165mm)

Valve Spring Adaptor Sizes: 1"(25mm) & 1.3/16"(30mm)

Double Ended Adaptor Reverses 1.1/16"(27mm) & 1.1/4"(32mm)

No.J6231 Heavy-Duty Valve Lifter For OHC Engines

No.J6235 Double Acting Valve Lifter For OHC Engines

Designed for large petrol and diesel engines. Unique "direct action" compressor gives improved visibility when used in difficult areas

Designed for use on multi valve petrol and diesel engines with deep seated valves. Also suitable for general use on a wide range of over head cam, over head valve & CVH engines. Universal model with unique dual cam-action, parallel lift, plus automatic locking reversible jaw.

No.4419 Flexible 14mm and 18mm Air Hold Tool

No.A1098 Hand Held Valve Spring Compressor

Use to hold valves into head when replacing valve seals or springs. Flexible hose has 14 and 18mm threads with O-ring seals for quick easy connection. Use with #4057, #4115, #4120, #4123, #4140, #4158 and other valve lifters. Inlet Thread: 1/4"NPT Female. Length: 14"(355mm)

Quick and easy for valve removal and assembly where valve springs require only hand pressure. Ideal for replacement of valve stem seals without removing the cylinder head. Supplied with two recessed adaptors: 21mm and 25mm. Length: 7.7/8"(200mm) No.4121

No.4418 14 & 18mm Air Hold Fitting Set l

Adaptors Fit Standard 1/4" Pipe Air Hose Couplings

Use air holds to apply air pressure to hold valves closed while replacing valve springs. Remove spark plug and screw air hold into port. Fasten air hose fitting and apply pressure. Use with #4057, #4115 ,#4120, #4123, #4140, #4158 valve lifters. Supplied in sturdy vinyl pouch. Lengths: 1.1/2"(40mm), 1.3/4"(44mm) TM

No.4122

Recessed Valve Adaptors

No.4158 CVH Valve Spring Compressor

Made from durable nylon to prevent damage to cylinder heads. They work with standard valve lifters & clamp into valve lifter jaws.

No.4121 Small Recessed Valve Adaptor

Diameter: 1.1/16"(27mm)

Length: 57mm

No.4122 Large Recessed Valve Adaptor Diameter: 1.1/4" (32mm)

Length: 70mm

Use With #4418 or #4419 Air Holds Permits valve stem oil seals and valve spring replacement without the need to remove the cylinder head. Tempered drop forged alloy steel. Length: 4"(100mm) l


125

T

&E OOLS

ENGINE SERVICE TOOLS - VALVE LIFTERS Use with # 4418 or # 4419 Air Holds

No.4117 Universal Valve Lifter Heavy-duty construction, universal application. This valve lifter will compress the stiffest valve springs. Fully adjustable to suit any valve stem length. Slim rugged jaws allow maximum room to remove or replace valve collets. Supplied with #4118 straight and #4119 offset jaws. Maximum Opening: 9"(230mm) Throat Depth: 9"(230mm) No.4118 No.4119

No.4058 OHV Spring Compressor Lever Type 3/8" & 7/16" Studs

Replacement Straight Jaw Set to Suit #4117 Valve Lifter Replacement Offset Jaw Set to Suit #4117 Valve Lifter

No.4150 Air Operated Valve Lifter


Just two fingers do the work! Will compress the heaviest of valve springs. Features controlled release action. Works with shop air 90 to 125psi and develops pressure equal to three times the line pressure. Ideal for all car, truck, tractor, marine & industrial engines. Includes 3 Jaws Sets: #4151, #4152, #4153 Maximum Opening: 8.3/4"(222mm) Throat Depth: 8.7/8"(200mm)

No.4056 Thin Jaw Overhead Valve Spring Compressor

Replacement Jaws:

No.4151 Straight Jaw Set (Small) Spring Diameter: 7/8" to 1.7/8" (22 to 48mm)

No.4152 Offset Jaw Set (Medium)

Removes valve springs on most cars with overhead valves without removing cylinder head.Offset jaws grip springs in parallel compression position. Can be used on high performance engines. Length: 5.3/4"(145mm)

Spring Diameter: 1" to 2" (25 to 50mm)

No.4153 Straight Jaw Set (Large) Spring Diameter: 1.1/2" to 2.1/2" (38 to 65mm)

No.4150-R

Removes and installs valve springs with the heads on or off the engine. Handles 1 to 2"(25 to 50mm) diameter springs. Press down to compress coil spring, then remove valve keepers and release slowly. Fits 3/8" & 7/16" rocker studs. Height: 6.1/2"(165mm) Length: 14.1/2"(368mm)

Air Cylinder Repair Kit Includes 14mm & 18mm Air Hold Adaptors

No.4115 Universal OHV Spring Compressor l

Extra Deep Reach for Overhead Camshaft Engines

This universal valve spring compressor has been developed to remove and install valve springs with the cylinder head still on the engine in the car, or with the cylinder head removed. The multi-point adjustable base of this tool bolts securely to the head while the adjustable lever mechanism pivots from the bar thus compressing the spring. Quick removal and installation of the spring retaining keepers is easily accomplished through the large openings on both sides of the compression tube. Includes air hold adaptors for both diesel and petrol engines. Supplied in blow mold case. Bar Length: 20"(508mm)

126

TM

No.4124 Motor Cycle Valve Lifter Special design for motor cycle overhead cam engines. Compact, rugged, powerful & is simple and fast to use. 3 Recessed valve adaptors included. 19, 23 & 25mm. Maximum Opening: 5.1/2"(140mm) Throat Depth: 4"(100mm)


ENGINE SERVICE TOOLS - VALVE ADJUSTERS

No.4131 Side Valve Spring Compressor Approved for Briggs & Stratton The ideal tool for removing and replacing valve springs on Briggs and Stratton and other small side valve engines. Long and slender, it is adapted to reach into small recesses. Spring steel jaws are adjustable in width to fit the valve springs and have edges so thin they can be easily forced under and over the ends of the valve spring to compress it for removal. Length: 9"(230mm) l

No.4156 Valve Collet Replacer Replaces tapered split collets on recessed valve springs quickly and easily. The spring loaded unit places collets in position on recessed heads instantly. Includes magnet on reverse end to retrieve collets. Length: 8.1/4"(210mm)

T

&E OOLS

No.4123 Bar Type Valve Spring Compressor l Locks onto Over Head Valve Rocker Stud Universal application on overhead valve engines. Use with or without removing cylinder head. Designed for V8 engines and other engines with stud type rocker arms. Fasten tool to stud for lever point to compress valves. Length: 12.9/16"(320mm)

No.4154 Twin Cam Valve Collet Installer Works with multi valve engines eg. (16V & 24V & 32V) Replaces tapered split collets on recessed valve springs quickly and easily. The spring loaded unit places collets in position on recessed heads instantly. Includes magnet on reverse end to retrieve collets. Length: 8.1/4"(210mm) 10mm 12Pt Opening

17mm Hex Drive

No.88250 Shim Style Valve Adjusting Set

No.4625 Honda VTEC 10mm Valve Adjusting Tool

Suits Nissan & Toyota Engines For overhead camshaft engines using spacer shims. Includes two special wedges to suit Toyota and Nissan engines with special pliers for removing and replacing the spacer shims to obtain the correct thickness of shims. Pliers Length: 8"(200mm)

For adjusting valves on Honda & Acura VTEC engines. Long socket raises the adjustment position to where there is more room to work. Holds adjusting screw positively in place while jam nut is tightened. Eliminates miss adjustment typically experienced using conventional tools. Length: 4"(100mm)

No.4955 5Pc. Universal Valve Adjustment Wrench Set

No.4157 3Pc. Valve Keeper Installing Kit

This two in one tool features a window in the socket. The visual contact allows for quicker valve adjustment times as the technician can hold the adjustment screw exactly where he wants it. The unique handle pivots from one side to the other, so the window is always visible. Hex Sizes: 10mm, 12mm, 13mm, 1/2" & 9/16" Lengths: 7.1/2"(190mm)

Magnetic jaws manoeuver the keepers into the valve stem grooves for installation. Easily reaches into recessed spring pocket to retrieve released valve keepers. Retrieves small parts from any recessed or hidden area. Small, medium & large valve keeper installing tools to cover all size valve collets. Lengths: 7.1/2"(190mm)

l

TM


127

T

&E OOLS

ENGINE SERVICE TOOLS - VALVE TOOLS

No.V20 Adjustable Valve Guide Cleaner

No.4932 Valve Stem Seal Removal Pliers

Valve guides cleaned with this tool are really cleaned with no gum,

no carbon and no scale left. Use manually or with 1/4" electric drill. Blades of flat spring stock are extremely flexible and give a fine cutting action. Correct tension for various guide hole sizes is regulated by the adjusting nut. Capacity: 5/16" to 5/8"(8 to 16mm) Length: 8.7/8"(225mm)

Reach down around the valve stem into confined areas of the valve guide for seal removal. Serrated jaws grip firmly onto seals for easy removal. Length: 10"(250mm)

No.4312-S Valve Lapping Tool Set

a

For hand lapping engine valves. Neoprene rubber cups are resistant to oil, gasoline & grease. Set contains 5/8" & 13/16"(16 & 21mm) and 1.1/8" & 1.3/8"(28 & 35mm) double end valve lapping tools.

No.4301 Oscillating Valve Lapper

Available Separately:

Short back and forth strokes constantly advancing the valve to a new seat position thus insuring a perfect seal in the least amount of time. A thrust ball bearing on the spindle gives smooth action. Set Includes: Vacuum cup, slotted valve adaptor & grinding spring. Length Long Stem: 13"(330mm) Length Short Stem: 9"(229mm)

a

No.4311 Vacuum Cup Valve Lapper Cup Sizes: 5/8" & 13/16"(16 & 21mm) Length: 9"(228mm) a

No.4313 Vacuum Cup Valve Lapper Cup Sizes: 1.1/8" & 1.3/8"(28 & 35mm) Length: 9"(228mm)

No.4155 Magnetic Recessed Valve Adaptor l For OHC Applications For use on recessed valve springs on overhead cam applications. Removable magnetic ring grabs split collets easily. Tool fits into jaws of most standard valve lifters. Diameter: 1.1/4"(32mm) Length: 2.1/4"(57mm)

No.4302 Oscillating Valve Lapper Short back and forth strokes constantly advancing the valve to a new seat position thus insuring a perfect seal in the least amount of time. A thrust ball bearing on the spindle gives smooth action. Includes: 7/8"(22mm) & 1.1/8"(28mm) Vacuum cups. Length: 6.3/4"(172mm)

No.4148 30mm Magnetic Recessed Valve Collet Clamp For use on recessed valve springs on overhead cam applications. Removable magnetic ring grabs split collets easily. Fits into jaws of most standard valve lifters. Length: 60mm Diameter: 30mm

No.4931 Valve Stem Seal Installation Kit

Set Contains:

No.4149 33mm Magnetic Recessed Valve Collet Clamp For use on recessed valve springs on overhead cam applications. Removable magnetic ring grabs split collets easily. Fits into jaws of most standard valve lifters. Length: 60mm Diameter: 33mm

128

TM

Valve Stem Seal Removal Pliers Length: 10"(250mm) They reach down around the valve stem for valve guide seal removal. Valve Stem Seal Aligning Guides 1/2"(12.7mm), 9/16"(14.3mm) Valve Stem Seal Installer Assures positive even replacement of seals & comes with 7 screw on seat adaptors & two seal aligning guides. Sizes: 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 8mm, 10mm Supplied in blow mold case. a

a


ENGINE SERVICE TOOLS - VALVE / TAPPET

No.4982 Long Reach Valve Seal Removal Pliers For valve stem sealing rings, the special long slim form allows quick easy and safe removal of valve-stem oil-seals, even on 4-valve cylinder heads. Length: 12"(300mm)

No.4130 Valve Collet Release Slide Hammer

T

&E OOLS

No.4163 Valve Shim Disc Removing Pliers Special design tips on the pliers for removing shim discs on overhead and twin overhead camshaft engines. Length: 11"(275mm)

No.92121 Mitsubishi Hydraulic Valve Lifter Remover

Depresses the valve spring on Mitsubishi DOHC engines for easy removal and replacement of the hydraulic valve lifters. Use on Turbo and Non-Turbo 1.6L 4 cylinder (1989 and later), Use for removing valve springs on overhead valve engines. The slide hammer is used to free the split collets before compressing the 2.0L 4 cylinder (1989 and later), 3.0L 6 cylinder (1991 and later) valve spring. Valve Spring Cap Size: 34mm Length: 13"(330mm) and 3.5L 6 cylinder (1995 and 1996). Length: 11.1/4"(286mm)

No.4925 Universal Valve Stem Seal Remover

Universal slide hammer valve stem remover features expandable jaws that lock into valve stem seals. Slide hammer enables seals to be removed without scoring or damaging bore in cylinder-head. Min Hole Diameter: 21mm Max Hole Diameter: 70mm Length: 12.1/4"(310mm)

No.4164 180mm Valve Adjusting Depressor Special design bar depressor to enable removal and replacement of spacer shims to obtain the correct camshaft height. Suits: Fiat Tipo 1.4DGT. Use in conjunction with #4163 Shim Pliers. Length: 180mm

No.4165 230mm Valve Adjusting Depressor

No.4981 Valve Stem Seal Pliers Peugeot, Citroen etc. For valve stem sealing rings. The special long, slim form allows quick, easy and safe removal of valve-stem oil-seals, on Peugeot, Citroen and many other vehicles. Length: 8.1/2"(215mm)

No.4166 245mm Valve Adjusting Depressor

Special design bar depressor to enable removal and replacement of spacer shims to obtain the correct camshaft height. Suits: Ford, Escort. Use in conjunction with #4163 Shim Pliers. Length: 245mm

No.4956 9/16" Valve Lash Adjuster

Offset valve adjustment wrench with T-handle hex keys makes valve adjustments Special design bar depressor to enable removal and replacement of possible without having to use three hands. spacer shims to obtain the correct camshaft height. Suits: Audi, VW, For use on adjusters fitted with hexagon Volvo. Use in conjunction with #4163 Shim Pliers. Length: 230mm head adjustment nut. Size: 9/16" 12 Point hexagon 3/16" & 7/32" T-handle hex key wrenches

No.4958 Click / Adjust Tappet Adjuster

Select the correct size 3/8" drive socket to fit tappet lock nut, unlock the nut and the slotted screwdriver blade can then adjust the tappet clearance. By holding adjustment with screwdriver handle tighten lock nut with socket and handle. Job can be done without using three hands. Size: 3/8"Drive 6mm Slotted screwdriver blade Length: 5.7/8"(150mm) TM

No.4957 5/8" Valve Lash Adjuster Offset valve adjustment wrench with T-handle hex keys makes valve adjustments possible without having to use three hands. For use on adjusters fitted with hexagon head adjustment nut. Size: 5/8" 12 Point hexagon 3/16" & 7/32" T-handle hex key wrenches


129

T

&E OOLS

ENGINE SERVICE TOOLS - VALVE TOOLS

No.6258 Adjustable Tungsten Carbide Blades Valve Seat Cutting Kit

Precision machined tungsten carbide blades produce valve seats with accurate seat angle, superior seat surface, and a true flat seal with the seats concentric to the valve guide. Contents: 3 Expandable pilots covering a range of 5.5mm thru to 9.5mm 4 Pin "T" Wrench Handle 37 to 46mm 68° & 45° Double Sided Tungsten Carbide Cutter 37 to 44mm 75° & 30° Double Sided Tungsten Carbide Cutter 28 to 35mm 75° & 45° Double Sided Tungsten Carbide Cutter

No.6257 Adjustable Tungsten Carbide Blades Valve Seat Cutting Kit Precision machined tungsten carbide blades produce valve seats with accurate seat angle, superior seat surface, and a true flat seal with the seats concentric to the valve guide. Contents: 5 Expandable pilots covering a range 5.5mm thru to 12.5mm 4 Pin "T" Wrench Handle 52 to 65mm 75° & 60° Double Sided Tungsten Carbide Cutter 46 to 60mm 45° & 30° Double Sided Tungsten Carbide Cutter 44 to 52mm 75° & 30° Double Sided Tungsten Carbide Cutter 37 to 46mm 68° & 45° Double Sided Tungsten Carbide Cutter 37 to 44mm 75° & 30° Double Sided Tungsten Carbide Cutter 28 to 35mm 75° & 45° Double Sided Tungsten Carbide Cutter

No.4930 Valve Stem Seal Installation Kit Set Contains:

1. Valve Stem Seal Removal Pliers Reach down around the valve stem into confined areas of the valve guide for seal removal. 2. Valve Stem Seal Installer assures positive even replacement of seals with ease and comes with 6 screw on seat adaptors. Sizes: 5mm, 6mm, 7mm, 8mm, 10mm, 11.5mm 3. Slide Hammer Valve Stem Seal Installer Supplied complete in blow mold carry case. Length: 16.1/2"(419mm)

Universal Valve Adjustment Tools Two in one tool features a window in the socket. The visual contact allows quicker valve adjustment times as the technician can hold the adjustment screw exactly where he wants it. The handle pivots from one side to the other, so the window is always visible. a

No.4950

Valve Adjustment Tool 10mm

Valve Adjustment Tool Lengths are all 7.1/2"(190mm)

Suits: Nissan, Toyota, Honda, Proton, Mitsubishi, etc. a

No.4951


Suits: Honda, Subaru, Proton, Mitsubishi, etc. a

No.4952

4950 thru 4954

J4950


Suits: Volkswagen, Porsche, etc. a

No.4953 No.4954

a

Valve Adjustment Tool 1/2" Universal Valve Adjustment Tool 9/16" Universal

No.J4950 Valve Adjustment Tool 10 & 12mm Universal

Pneumatic Valve Guide Punches

Use with Air Hammer with Standard .401" Parker Shank

Pneumatic valve guide drivers are used to remove and install replaceable valve guides on aluminium or cast iron heads.

No.1988 No.1990 No.1991 No.1992

130

Pneumatic Valve Guide Punch

1988

Pilot Size To Suit: 1/4" & 6mm

Length: 6"(150mm)


Length: 6"(150mm)


Length: 6"(150mm)

1991


Length: 6"(150mm)

1992



Pneumatic Valve Guide Punch TM

1990


ENGINE SERVICE TOOLS - TAPPET New Improved Model

No.4676 Expanding Collet Hydraulic Tappet Puller Removes hydraulic valve lifters from the top side of engine. Hardened steel jaws grip lifter by expanding into inside groove to pull valve lifters out of bore. Removes most stuck hydraulic valve lifters. Capacity: 1/2" to 3/4"(13 to 19mm) Length: 11"(280mm)

No.4678 Heavy Duty Hydraulic Valve Tappet Puller

T

&E OOLS

Not for use on Frozen or Gummed Lifters

No.4675 Quickie Hydraulic Tappet Remover Removes hydraulic valve lifters from the top side of engine. Hardened steel jaws grip lifter by expanding into inside groove to slide valve lifters out of bore. Capacity: 1/2" to 3/4"(13 to 19mm) Length: 11"(280mm)

No.92120 Ford Lifter Bleed Down Tool

Removes stuck hydraulic valve tappets with heavy duty slide hammer type tool. Jaws spread to clamp recessed area of tappet, use slide hammer to remove. Adapters convert tool to a puller for baked-in tappets. Turn adjusting nut with 5/8" wrench. Capacity: 1/2" to 3/4"(13 to 19mm) Length: 12"(300mm)

This useful tool has been developed to mechanically bleed down the lifters when checking valve clearance on Ford 5.0 Litre V8 engines. It easily attaches to the early cast design, as well as, the later model stamped version rocker arms. Length: 13.3/16"(335mm)

No.4756 Hydraulic Tappet Remover

No.4015 Over-Head Cam Follower Remover

Removes hydraulic valve lifters from the top side of engine. Hardened steel jaws grip lifter by expanding into inside groove to lift valve lifters out of bore. Capacity: 1/2" to 3/4"(13 to 19mm) Length: 11"(280mm)

No.4344 Rocker Stopper Oil Plugs Plug oil holes in ball-joint type rocker arms. Spring steel clips with gaskets stop splashing or squirting of hot oil while you adjust valve clearance. Designed for cars with hollow, oil-fed push rods. Length: 1"(25mm)

No.U1900 19mm Crowsfoot Tappet Adjusting Wrench Designed to allow adjustment of valve clearance without the need to remove the carburettor on Ford OHC and other engines with 3/4" or 19mm nut sizes. Size: 3/4"(19mm) Length: 4"(100mm) TM

Here is the easiest way to remove OHC followers from the cylinder head. Simply insert the remover, spread the jaws and attach a slide hammer, with a shaft size of either 1/2"UNC or 5/8"UNF, pop it out. Capacity: 5/8" to 11/16"(16 to 18mm) Length: 3.3/4"(95mm)

No.4342 Rocker Arm Oil Deflector Set For engines with pressure lubricated push rods. Deflects oil from rocker arm to valve chamber. 16 Individual deflectors in set permit both banks of valves to be adjusted simultaneously. Easily snapped on to rocker arm. Metal storage panel included with set.

No.4016 Rocker Arm Stud Remover & Installer For removal and installation of press fit rocker arm studs with either 5/16" or 3/8" diameter. Fits most GM and Ford vehicles with "press fit" rocker arm studs. This tool provides the correct method for removal and replacement of these difficult to service studs. Length Stud: 4"(100mm) Hex Body: 2.3/4"(70mm)


131

T

&E OOLS

ENGINE SERVICE TOOLS - CYLINDER HEAD

No.4710 Metric Dowel Puller Set At last a tool to handle the near impossible task of removing press fitted dowel pins from cylinder blocks, crankshafts or anywhere dowel pins are fitted. Supplied in blow mold case. Set Includes:


a

No.4710SLIDEH Slide Hammer 3lb(1.4kg) Length: 17.3/4"(450mm) No.4721 Collet Housing Length: 2.3/4"(70mm) No.4711 6mm Collet No.4717 12mm Collet No.4713 8mm Collet No.4718 14mm Collet No.4716 10mm Collet No.4719 16mm Collet

No.4720 Imperial Dowel Puller Set

At last a tool to handle the near impossible task of removing press fitted dowel pins from cylinder blocks, crankshafts or anywhere dowel pins are fitted. Supplied in blow mold case. Set Includes:


No.4710SLIDEH Slide Hammer 3lb(1.4kg) Length: 17.3/4"(450mm) No.4721 Collet Housing Length: 2.3/4"(70mm) No.4722 1/4" Collet No.4726 1/2" Collet No.4723 5/16" Collet No.4727 9/16" Collet No.4724 3/8" Collet No.4728 5/8" Collet No.4725 7/16" Collet Features Flex Arm with Clamp

No.6474 600mm Precision Straight Edge Used for checking warpage on engines and machine parts, etc. Made from high carbon steel and machined to accurate specifications and dimensions for exact measurements. "T" Shaped body with elongated holes prevent any distortion. Supplied in metal storage case. Depth: 1.3/8"(35mm) Width: 5/8"(16mm) Length: 23.5/8"(600mm)

No.5598 3/4"Drive Torque Angle Gauge Use on newly required "Torque to Yield" bolts on aluminium cylinder heads etc, on many late model vehicles. Gives accurate angle measurement as per specified requirements. A must for correct new automotive engine assembly. Range: 0 to 360° in 2°increments Diameter: 3.1/2"(90mm) Features Flex Arm with Clamp

No.5597 No.4345 1/2"Drive Torque Angle Gauge Cylinder Head Holding Stands l Features Flex Arm with Clamp Tapered Pins Fit All Stud Hole Sizes Sturdy stands hold cylinder heads safely and securely while you repair cracks, grind seats, clean carbon or perform valve guide work. There is ample clearance under heads for knurling and reaming valve guides. Two stands per set. Overall Height: 10.1/2"(265mm) l

132

TM

Use on newly required "Torque to Yield" bolts on aluminium cylinder heads etc, on many late model vehicles. Gives accurate angle measurement as per specified requirements. A must for correct new automotive engine assembly. Range: 0 to 360° in 2°increments Diameter: 2.3/4"(70mm)

No.5595 Cylinder Head Torque Angle Gauge Use on newly required "Torque to Yield" bolts on aluminium cylinder heads etc, on many late model vehicles. Gives accurate angle measurement as per specified requirements. A must for correct new automotive engine assembly. Range: 0° to 360° in 1°increments Diameter: 2.3/4"(70mm) Drive: 1/2"Square


ENGINE SERVICE TOOLS - GENERAL

T

&E OOLS

No.4730 Metric Threaded Adaptor Slide Hammer Rail Pin Puller Set 2.1/2lb Slide hammer with six interchangeable threaded pins for extracting pins and studs with threaded holes fitted to many engines etc. The threaded adaptors fit the following sizes: 1: 4mm 2: 5mm 3: 6mm 4: 8mm 5: 10mm 6: 12mm Length: 14"(356mm)

No.4702 Benz & BMW Guide Rail Dowell Pin Puller Can remove even the most stubborn pins from the cylinder head, unlike the short slide hammer previously used to attempt this job. The new designed puller incorporates a thrust bearing to ease the pulling action. This heat treated tool has been tested and proven to be the best solution on many vehicle makes. Supplied with two interchangeable adaptors. Sizes: 6 x 1.0mm & 8 x 1.25mm Length: 5.1/2"(140mm)

No.4928 Universal Camshaft Pulley Rotating Tool

No.6278 BMW Camshaft Sprocket Extractor & Installer

Suitable for timing pulleys with holes from minimum 16mm eg: VW, Audi, Ford, Opel, Peugeot, Renault, Citroen, Rover, Volvo, Japanese Applicable for BMW 4- and 6-Cylinder twincam engines M42, M44, vehicles etc. To prevent pulley on camshaft, injection pump, etc. M50 and M52 with Vanos unit. Required for removing and installing from rotating. Length: 14.1/8"(360mm) the Vanos adjusting unit with disc spring. Length: 6.3/4"(170mm) Suits Lexus & Toyota

No.4160 Auto Valve Tool

280 ft/lb Torque The Auto Valve Tool Required to Seat removes and replaces The Pulley Properly valve keepers on all petrol and diesel overhead valve engines, No.4640 including VW Rabbit, motorcycles, marine and aircraft engines .Use and instead of other valve spring Harmonic Damper Pulley Holding Tool Holds the pulley stationary to remove and install centre bolt on Lexus compressors. Use only with a soft faced hammer. Magnet retains keepers when removing/replacing on the valve stem. and Toyota engines without having to remove the radiator. Suits: Lexus 1990 and later: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, 4.7 V8. Toyota 1992 and later: 3.0 V6, 3.3 V6,4.0 V6, 4.7 V8.

Piston Locating Tools Tool screws into spark plug hole to stop piston in a position nearing top dead centre. Use with #4096 Timing Degree Wheel and rotate engine in reverse to reach piston stop again. Take degree measurements of both stop positions and half the difference of degree readings is exact top dead centre.

No.J4222 30Pc.Crank Pulley Hollow Locking Plate Set Locking Plate Set for locking crankshaft pulleys on Japanese engines. TM

No.4750 14mm Piston Locating Tool Thread: 14mm x 1.25 pitch

Hex Head: 17mm

Thread: 10mm x 1.0 pitch

Hex Head: 14mm

No.4749 10mm Piston Locating Tool


133

T

&E OOLS

ENGINE SERVICE TOOLS - CYLINDER HONES Engine Cylinder Hones 4320 Small Engine Cylinder Hone Ideal deglazing hone for lawn mowers, outboard motors, compact and small stationary engines. Supplied with three 2"(50mm) long 220 grit stones. Capacity: 1.1/4" to 3.1/2"(32 to 90mm) Length: 9"(228mm)

2" Replacement Stones

2" Replacement Stone Sets 3" Replacement Stones

a

4321

Fine Stone Set 3Pc. Length: 2"(50mm)

Grit: 400

Suits: #4320 hone

a

4323

Medium Stone Set 3Pc. Length: 2"(50mm)

Grit: 220

Suits: #4320 hone

a

4322

Coarse Stone Set 3Pc. Length: 2"(50mm)

4325

4320

Grit: 100

Suits: #4320 hone

Standard Engine Cylinder Hone Hone and remove glaze from cylinders. Adjustable spring tension for positive cutting action. Set diameter with special spread limiter. Supplied with three 4"(100mm) long 220 grit stones. Capacity: 2" to 7"(50 to 180mm) Length: 11.1/2"(292mm)

4325

4325-F

Replacement Flexible Shaft for #4325

4330

Large Three Leg Engine Cylinder Hone 11"(280mm) Capacity Hone and remove glaze from cylinders. Adjustable spring tension for positive cutting action. Set diameter with special spread limiter. Supplied with three 4"(100mm) long 220 grit stones. Capacity: 2" to 11.1/2"(50 to 290mm) Length: 15"(381mm) l

4333

Large Two Leg Engine Hone 9"(230mm) Capacity Hone and remove glaze from cylinders. Adjustable spring tension for positive cutting action. Set diameter with special spread limiter. Supplied with two 3"(75mm) long 220 grit stones. Capacity: 3" to 9"(75 to 230mm) Length: 11"(279mm) l

4" Replacement Stones

Engine Cylinder Hone Replacement Stones 4" Replacement Stone Sets a

4326

Fine Stone Set 3Pc. Length: 4"(100mm) Grit: 400 Suits: #4325, #4330, #4333

a

4324

Medium Stone Set 3Pc. Length: 4"(100mm) Grit: 220 Suits: #4325, #4330, #4333

a

4327

Coarse Stone Set 3Pc. Length: 4"(100mm) Grit: 100 Suits: #4325, #4330, #4333

a

3" Replacement Stone Sets 4330

4333

a

4328

Fine Stone Set 3Pc. Length: 3"(75mm) Grit: 400 Suits: #4325, #4333

a

4331 Bottle Brush Type Ball Hones are listed on page 147

Medium Stone Set 3Pc. Length: 3"(75mm) Grit: 220 Suits: #4325, #4333

a

4329

Coarse Stone Set 3Pc. Length: 3"(75mm) Grit: 100 Suits: #4325, #4333

134

TM


ENGINE SERVICE TOOLS - CYLINDER BLOCK

T

&E OOLS

For Dry Sleeve Manual & Hydraulic Sleeve Pullers See Puller Section on Page 311

No.2-1205 Universal Puller for Wet Type Sleeves This puller features adjustable jaws to fit cylinder sleeves 3" to 6.1/2"(75 to 165mm) Cone adjustment positions the puller jaws and they are locked into place when the locking bar is tightened. To aid in breaking "frozen" sleeves loose, the adjustable bridge is positioned on the cylinder block and the bearing-mounted forcing nut is tightened to break the seal. Finally sleeves are removed with the use of the 5lb. 5/8" UNF threaded slide hammer. Length: 18"(457mm)

No.4289 Standard Ridge Reamer

Lathe Action Popular Size No.4288 Spring loaded tungsten carbide cutter maintains Small even cutting pressure Ridge Reamer on cylinder walls. Even l Lathe Action those with ovality wear. l Small Engine Model Smooth cutting is assured Spring loaded tungsten carbide cutter by the fine thread feed. Change from one maintains even cutting pressure on cylinder cylinder to the next without re-adjustment of walls. Fine fit adjustment and can change from the precision spring loaded cutter. one cylinder to the next without re-adjustment. Full instructions included. Capacity: 3" to 5"(75 to 125mm) Capacity: 2" to 3"(50 to 75mm) Length: 5"(127mm) Length: 4"(100mm) No.4288-C Replacement Carbide Cutter No.4289-C Replacement Carbide Cutter

No.4290 Large Ridge Reamer

l

l

l l

Lathe Action Truck Engines

Same features as #4289 with capacity to handle truck and large size cylinder bores Capacity can be extended using #4291 Legs. Full instructions included. Capacity: 4" to 6"(100 to 150mm) Length: 6.3/8"(162mm) No.4290-C Replacement Carbide Cutter

No.4918 Welsh Plug Installing Tool Set This tool speeds up the cumbersome, awkward job of replacing welsh plugs. It drives them into place securely eliminating the need to remove engines, mounts or to cut fire walls. Set Contains:

Part No. 4918-1 4918-2 4918-3 4918-4 4918-5

Available Separately

Description 16" Bent Freeze Plug Driver Coupling Nut 20mm x 35mm Adaptor 25mm x 35mm Adaptor 30mm x 41mm Adaptor

No.4919

Part No. 4918-6 4918-7 4918-8 4918-9 4916

Description 35mm x 45mm Adaptor 40mm x 50.5mm Adaptor 45mm x 60mm Adaptor 50mm x 60mm Adaptor Welsh Plug Puller

Master Freeze Plug Installation Tool Kit

Eliminates the need to remove engines, mounts or to cut into fire walls. All parts are machined from high quality alloy steel with nickle chrome plate finish. Set Contains:

Part No. 4919-1 4919-2 4919-3 4919-4 TM

Description 18" Bent Freeze Plug Driver Coupling Nut 1.3/4" x 2.3/4" Adaptor 1.1/2" x 1.7/8" Adaptor


Part No. 4919-5 4919-6 4919-7 4919-8

Description 1.1/4" x 1.5/8" Adaptor 1" x 1.3/8" Adaptor 3/4" x 1.5/16" Adaptor 8" Straight Freeze Plug Driver

No.4291 Large Ridge Reamer Extension Set These extension legs fitted to #4290 large ridge reamer extend it's capacity to a full 7"(180mm). Capacity: 6" to 7"(150 to 180mm)

No.4916 Welsh Plug Puller Welsh Plug Puller removes frozen plugs up to 2"(50mm) in diameter. Just drill a 17/64" hole and screw in the forcing screw. Use a 5/8" socket or wrench to remove the freeze plug from its housing. Length: 2.3/4"(70mm)


135

T

&E OOLS

ENGINE SERVICE TOOLS - PISTON RING Depress Lever to Open Ring Compressor with Lever Handle

No.4217 Small Engine Piston Ring Compressor Beaded along lower edge to prevent compressor entering cylinder. Utilises dependable friction-type brake to hold rings in compression. Capacity: 1.3/4" to 3.1/2"(45 to 90mm) Depth: 1.1/2"(38mm)

No.4214 Standard Ring Compressor l

Positive Locking Action

No.4216 Large Ring Compressor l

Compressor band takes all rings at once. Self locking friction brake with trigger prevents premature release ensuring smooth operation. Double tension bands of the highest grade spring steel eliminate any bottom flare. Capacity: 2.1/8" to 5"(55 to 125mm) Depth: 4"(100mm)


Compressor band takes all rings at once. Self locking friction brake with trigger prevents premature release ensuring smooth operation. Double tension bands of the highest grade spring steel eliminate any bottom flare. Capacity: 3.1/2" to 7"(90 to 180mm) Depth: 4"(100mm)

No.4215 Diesel Ring Compressor l


Extra deep band takes all rings at once, including skirt rings. Specially designed for heavy-duty skirt ring pistons. Compressor is equipped with four tension bands and friction brake with trigger preventing premature release and ensuring smooth operation. The four tension bands of the highest grade spring steel eliminate any bottom flare. Capacity: 3.1/2" to 7"(90 to 180mm) Depth: 6.1/2"(165mm)

No.CL337 9Pc. Piston Ring Service Set Set Includes: Ring Compressor 55-125mm, 75mm Long

Ring Compressor 90-175mm, 90mm Long Ring Compressor 90-175mm, 100mm Long Piston Ring Expander 50 to 100mm Capacity Piston Ring Groove Cleaner 50 to 130mm Capacity Blade Sizes: 1/16" to 3/16", 2 to 2.5mm, 1.2 to 5.5mm Offset Phillips & Slotted screwdriver.

136

TM

No.4216-S Can Be Used for Compressing Automatic Transmission Pump Seals

No.4216-S Extra-Large Ring Compressor Self locking heavy-duty ratchet pawl prevents premature release. Double tension bands of the highest grade spring steel eliminate any bottom flare. Adjusting screws on ratchet release allow tension and friction to be set for smooth operation. Capacity: 7" to 10"(180 to 255mm) Depth: 3.1/2"(90mm)

No.7082 Universal Piston Pin Remover & Installer

Includes all adaptors to service piston and rod assemblies from 3.1/8" to 4.3/4" diameters and piston pin size of 0.885" to 1.062 diameter. Use with a workshop press to remove and replace piston pins with ease. The anvil support assures that the pressing force is never applied directly to the piston, it floats free, eliminating any possible damage to the assembly. Removes and installs press-fit piston pins of 0.855"dia. to 1.062"dia. Pin Guide Sizes: 21.7mm, 22.7mm, 23.5mm, 24.5mm, 25.1mm, 26.1mm, 26.7mm, 27.6mm


T

&E OOLS

ENGINE SERVICE TOOLS - PISTON RING Piston Ring Compressors "Band Type" 4220 Wrinkle Band Ring Compressor One Single Adjustment Does All Cylinders Compresses piston rings with less ring contact and lower friction, allowing pistons to slide in easier and faster. Cam lever operation requires just one setting adjustment for fast piston to piston change. Ideal for barrel cylinders which install over piston, as the band separates. Capacity: 3" to 5"(75 to 125mm) Depth: 1.1/2"(38mm)

l

4980

Ring-O-Matic Piston Ring Compressor Complete set of bands and pliers, makes repetitive ring installation easier. It speeds up work, reducing labour costs. Without taking the pliers off the band on which you are working, you can operate it from either vertical or horizontal positions. Pliers have fine ratchet mechanism which permits the bands to be contracted by minute graduations. To instantly release bands just depress thumb release lever. Hardened steel bands for durable wear. Supplied in handy fibreboard storage box. Capacity: 2.7/8" to 4.3/8"(73 to 111mm)

4220

Set Contains:

#4980-A Pliers #4980-B Band #4980-C Band #4980-D Band #4980-E Band #4980-F Band #4980-G Band

Length: 10.3/4"(275mm)

2.7/8" to 3.1/8"(73 to 79mm) 3.1/8" to 3.3/8"(79 to 86mm) 3.3/8" to 3.5/8"(86 to 92mm) 3.5/8" to 3.7/8"(92 to 98mm) 3.7/8" to 4.1/8"(98 to 105mm) 4.1/8" to 4.3/8"(105 to 111mm)

Individual & Additional Bands for No.4980 4980-B

Replacement Band for #4980 Size: 2.7/8" to 3.1/8"(73 to 79mm)

x 1.1/2"(38mm) Wide

4980

a

4980-C

Replacement Band for #4980 Size: 3.1/8" to 3.3/8"(79 to 86mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 3.3/8" to 3.5/8"(86 to 92mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 3.5/8" to 3.7/8"(92 to 98mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 3.7/8" to 4.1/8"(98 to 105mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 4.1/8" to 4.3/8"(105 to 111mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 4.3/8" to 4.1/2"(111 to 114mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 4.1/2" to 4.3/4"(114 to 121mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 4.3/4" to 5"(121 to 127mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 5" to 5.1/4"(127 to 133mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 5.1/4" to 5.1/2"(133 to 140mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 5.1/2" to 5.3/4"(140 to 146mm) x 1.1/2"(38mm) Wide Replacement Band for #4980 Size: 5.3/4" to 6" (146 to 152mm) x 1.1/2"(38mm) Wide Replacement Pliers for #4980 Length: 10.3/4"(275mm)

a

4980-D a

4980-E a

4980-F a

4980-G 4980-P a

4980-H a

4980-I a

4980-J a

4980-N a

4980-K a

4980-M a

4980-A

TM

Replacement Bands No's. 4980-B to 4980-P

Hold Tension on Pliers When Releasing Lever to Prolong Ratchet Teeth Life

4980-A


137

T

&E OOLS

ENGINE SERVICE TOOLS - PISTON RING

No.4200 Piston Ring Expander with Stop

Tapered jaws hold the ends of the ring to expand and slip easily over piston. Knurled adjusting knob and slide prevents over-expanding, reducing ring breakage. Handles Piston Ring Widths: 3/64" to 1/4" (1.2 to 6.3mm) on most cars and light trucks. Length: 6.1/2"(165mm)

No.4219 Piston Ring Expander without Stop

Universal application fits both small and large size piston rings. Tapered jaws hold the ends of the ring to expand and slip easily over piston. Handles Piston Ring Widths: 3/64" to 1/4" (1.2 to 6.3mm) on most cars and light trucks. Length: 6.1/2"(165mm)

No.4218 Universal Piston Ring Expander Universal design handles all ring widths to 1/4"(6.3mm) Flat and smooth edge jaws lock onto ring to enhance the gripping power. Eliminates damage and breakage of rings. Length: 6.1/4"(159mm)

No.4202 No.4201 No.4204 Small Piston Ring Expander Standard Piston Ring Expander Large Piston Ring Expander l

Approved for Briggs & Stratton

Replace piston rings without the danger of breakage or distortion. No adjustments needed, expands all ring styles whether square, diagonal or step-cut style. Capacity: 1.1/4" to 2.1/4"(32 to 60mm) Length: 9"(228mm)

l

Suits Most Popular Passenger Car Engines

Replace piston rings without the danger of breakage or distortion. No adjustments needed, expands all ring styles whether square, diagonal or step-cut style. Capacity: 2.3/4" to 4.1/4"(70 to 110mm) Length: 9"(228mm)

l

Suits Most Popular Truck Engines

Replace piston rings without the danger of breakage or distortion. No adjustments needed, expands all ring styles whether square, diagonal or step-cut style. Capacity: 4.1/2" to 7"(115 to 180mm) Length: 10"(255mm)

No.4222 Piston Ring Groove Cleaner l

Supplied with Two Blades: Imperial & Metric

Absolutely the best ring groove cleaner available today. Features fully adjustable depth stop to limit depth of cut and side flanges for slotted and standard pistons. Both metric and imperial cutters feature ring land trimmer as well as five different sized cutters. Spring detent ball controls alignment of blade. Cutters are hardened and ground. Capacity: 2.5/8" to 5"(65 to 130mm) Length: 11.3/4"(298mm)

No.4222-A

Replacement Imperial Cutter for #4222

Includes Sizes: 1/16", 5/64", 3/32", 1/8" & 3/16"

No.4222-M

Replacement Metric Cutter for #4222 TM

File piston rings with this portable rotary filer. Use to accurately size any make or diameter ring. Includes extra hard fine grit carbide coated cutter file. Supplied in blow mold case. Length: 7.3/8"(188mm)

No.4210-B Replacement Carbide Coated Cutter File Work Safely With Hand Tools - Wear Safety Goggles

Includes Sizes: 1.5, 2.5, 3.0, 4.0 & 5.0mm

138

No.4210 Piston Ring Gap Filer

ENGINE SERVICE TOOLS - VACUUM & FUEL

1/2" Drive No.4395 Electric Fuel Pump Gas Tank Retaining Ring Removal Tool

T

&E OOLS

No.4396 GM / Ford Diesel Fuel Cap Wrench

Design allows for easy removal and installation of Ford diesel fuel caps & other filler systems To remove or replace fuel pump retaining rings: Loosen lock nut on using the same configuration. tool and adjust length of tool so slot in ears fits over teeth in plastic Works on fuel caps from 1995 to present. Necessary where access ring. Tighten lock nut and loosen or tighten plastic ring using 1/2" is limited. Length: 4.5/8"(118mm) extension and ratchet wrench. Length: 8.1/4"(210mm)

No.4399 Ford Fuel Pump Wrench For removal and installation of the fuel pumps with a plastic retaining nut. Suits all Ford Falcon models Special 8 slot wrench with 103mm ID for removing and installing XE, XF to current. fuel tank lock-rings on vehicles with CFI & EFI Fuel systems. 1/2" Square Drive. Length: 10.1/2"(265mm) Diameter: 4.1/2"(115mm) Circle Diameter: 6.1/8"(155mm)

No.4408 Fuel Tank Sender Unit Wrench

No.4550 Honda / Acura Fuel Filter Banjo Bolt Socket

J444 0 17 mm

It's not easy removing the hard-to access, specially shaped banjo bolts attaching the fuel line to the fuel filter on 1992 and later Hondas and Acuras. Not only are they hard to get at, but using an open end wrench to remove them can strip the head. Now there's an easy, damage-free way to remove them: our #4550 Socket, specially designed to work on just this bolt style. Opening: 17mm x 22mm 3/8" Square Drive Length: 7/8"(22mm) New Heat Treated Alloy Steel

TUBE

No.4349 Hose Remover Pliers

HOSE BEING REMOVED

Remove vacuum and fuel hoses easily with these unique pliers. The sharp edge jaw grips securely on the tube whilst the smooth jaw pushes off the hose. Works on all hoses from 5/32" to 1/2"(4 to 13mm) diameter. Length: 7"(180mm)

No.4348 Vacuum Line Identifiers l Matches Up Lines & Ports Contains six sets of matching plugs and caps. Coloured sets eliminates incorrect hook-ups. Speeds work on emission controls, engine rebuilding, and cylinder heads. Made of natural rubber. Eliminates the need of referring to service manuals for re-assembly. Supplied with wire storage clip.

TM

J44 44

14m m

Toyota Fuel Pipe Line Nut Wrenches Special single side flare nut wrenches to reach and access the fuel feed pipe line nut fitted to later model Toyota and other vehicles.

No.J4444

14mm Fuel Pipe Line Nut Wrench

Opening: 14mm 6 Point 3/8"Square Drive Length: 3.5/8"(92mm)

No.J4440

17mm Fuel Pipe Line Nut Wrench

Opening: 17mm 6 Point 3/8"Square Drive Length: 3.7/8"(98mm) Extra Large Capacity 1.7/8" (48mm)

No.4347 X-Large Vacuum Hose Remover Pliers Remove vacuum and fuel hoses easily with these unique pliers. The sharp edge jaw grips securely on the tube whilst the smooth jaw pushes off the hose. Works on all hoses from 5/32" to 1.7/8"(4 to 48mm) diameter. Length: 9.1/2"(240mm)

No.4350 Vacuum & Fuel Line Stoppers Stepped design plugs fit all 1/8", 3/16", 1/4", 5/16", 3/8" & 1/2"(3 to 13mm) hoses. Tapered caps close tubes. Use during tune-ups, vacuum tests, fuel pump repairs etc. Bead chain supplied for ease of storing.


139

T

&E OOLS

ENGINE SERVICE TOOLS - CRANKSHAFT

No.9582 Universal Pulley Holder

No.3471 Universal Pulley Holding Tool Designed to trap and hold bolt-on pulleys by gripping on the mounting bolts, works on most applications where studs protrude. It is ideal for removing and replacing thermostatic fan assemblies while eliminating the need for various sized holding wrenches. Length: 22"(560mm)

Features 5mm & 9mm pins which locate into pulley holes to prevent the flywheel & clutch assembly from rotating whilst servicing the motor. Adjustable lock screw enables adjustment to all diameters. Capacity: 1/2" to 9"(13 to 225mm) Length: 13"(330mm)

Camshaft Pulley Holding Tools No.4929 Camshaft Pulley Holding Tool Pin Centres: 3"(75mm) Length: 16"(410mm)

No.3475 Universal Pulley & Camshaft Holding Tool

No.A1081 Adjustable Camshaft Pulley Holder

Pin Centres: 1" to 4"(25mm to 100mm) Length: 16"(410mm) Designed with grooved pins to hold the camshaft pulley stationary while loosening & tightening the centre shaft bolt on overhead cam Supplied with 5 pairs of different size adaptors engines, on transverse mounted V6 engines such as the VG30 used Hook jaws hold bolt-on pulleys by gripping on the mounting bolts. in Nissan Maximas, as well as, the 3VZFE & IMZFE engines used Four sets of grooved pins hold the camshaft pulley stationary on OHC engines, eg: Nissan, Toyota, Mazda etc. Length: 22"(560mm) in Toyota Camrys. The rear pulleys on these models are in very close proximity to the shock tower making removal & replacement difficult without these locking devices.

No.4645 Honda Crankshaft Pulley Holding Tool

No.J1807 Camshaft Drive Belt Pulley Puller Special puller designed for pulling camshaft pulley wheels on 4 & 6 cylinder, V6 and V8 engines on VW and Audi petrol engines. Body Length: 5.1/4"(133mm) 1/2"Drive

120mm Long

No.4639 Honda Universal Crankshaft Pulley Holding Wrench Holds the harmonic balancer pulley from rotating when removing the pulley bolt. There is a hole in the centre of the tool to allow the use of a socket and extension to break loose or tighten the pulley bolt. Suits Honda models: Accord, Civic, CRV, Insight, Odysey, Prelude, S2000, Integra, Legend, NSX etc.

Suits Honda No.4650 Crankshaft & Harmonic Balancer Holder Set

For removal & installation of crankshaft pulley attaching bolt. Special sliding dowel assembly adjusts to fit into holes in crankshaft pulley. Prevents crankshaft & engine movement when held with breaker bar. Hole in centre allows access to crankshaft pulley bolt with socket. Fits most Honda engines, including Accord, Civic, CRX, CRV, Insight, Prelude S2000, Integra, Legend, NSX. Length: 26"(660mm)

140

TM

For removal and installation of crankshaft pulley attaching bolt. Special sliding dowel assembly adjusts to fit into holes in crankshaft pulley. Prevents crankshaft and engine movement when held with breaker bar. Hole in centre allows access to crankshaft pulley bolt with socket. Fits Accord, Civic, CRX & Prelude. Facilitates timing belt change. Length: 7.3/4"(197mm)

No.4635 Crankshaft Pulley Holding Tool

Suits Honda Prelude and some Honda Acura V6 engines. For removal and installation of crankshaft pulley attaching bolt. Hexagonal shape mates with hole in crankshaft pulley. Shallow 1" (25.4mm) overall depth fits tight into the engine compartment areas. Length: 8.1/2"(216mm)

No.J1860 Universal Grooved Pulley Puller Puller has adjustable arms to pull most ribbed & groove type engine pulleys fitted to late model engines. Suitable for use on crankshafts, alternators, air conditioning compressors, water pump pulleys, etc. Maximum Spread: 6.1/2"(165mm)


T

&E OOLS

ENGINE SERVICE TOOLS - CRANKSHAFT

No.4366 Mazda Crankshaft Holding Tool

For holding the crankshaft stationary so that crankshaft centre bolt can be removed or tightened. Bolts directly to the crankshaft using pulley attaching bolts. Use with 1/2"drive socket bar for holding when tightening or loosening the crankshaft centre bolt. Suits: Mazda 1986-91 323 1.6Litre engines Mazda 1990-91 Miata 1.6Litre engines Length: 4.3/4"(120mm)

No.7521 Flywheel Holder / Turner

Hook tool into flywheel teeth to rotate crankshaft. Spring tension helps tool engagement on flywheel. Uses are engine assembly, transmissions, etc. which require the crankshaft to be in a specific position. Length: 14.1/4"(360mm)

No.4709 Ford Rear Main Seal Installer

Ensures that the rear main seal is set to the correct depth on the crankshaft. Fits over the seal and by alternately tightening the two bolts the seal is pulled into place quickly, easily, and with no damage to the rear main seal. Works on Ford with 2.0 & 2.3L 4-cylinder engines; 3.0 & 3.8L V-6 engines; and 4.6 and 5.0L V-8 engines. Diameter: 4.1/4"(108mm)

No.4708 Rear Main Bearing Oil Seal Deluxe Kit

No.A1093 Subaru Impreza Crankshaft Pulley Remover & Replacer

Removes and replaces crankshaft pulley on Subaru Impreza engines. Pin Spread Diameter: 55mm x 55mm Length: 30.1/2"(770mm)

No.J4200 Ford Front Crankshaft Hub Bolt Remover Removes & installs front crankshaft pulleys, permitting in-chassis replacement of timing belts. Suits Ford Escort/Lynx 1.6Litre engines. Size: 3/4"(19mm) x 1/2"Sq. Drive Length: 9.1/2"(241mm)

No.4707 GM V6 3800 Commodore Rear Main Bearing Oil Seal Installer Essential tool needed for installing and replacing rear main bearing oil seal on GM Holden V6 3800 engines. Diameter: 3.7/8"(165mm) 124mm Long

No.4706 GM V6 3800 Commodore Rear Main Bearing Housing Aligner Set

98.5mm Diameter

Essential tool for servicing GM Holden V6 3800 engines when replacing rear main bearing oil seal.

No.4714 Rear Main Bearing Oil Seal Remover & Installer Kit

Eliminates the need to remove engine or crankshaft when replacing either wick or neoprene upper rear Tool removes and installs upper rear main oil seals with engine and main bearing oil seals. Saves many hours. crankshaft in place. It works on both wick and neoprene type seals. Comes complete with worn seal remover and stainless steel "Chinese Finger" type grip won't slip from the seal during installation. "Chinese Finger" seal installer.

No.J1805 Crankshaft Pulley & Drive Belt Pulley Puller

No.A1115 Crankshaft Pulley & Camshaft Pulley Puller

Universal crankshaft & camshaft pulley puller. Used on pulleys with Crankshaft & camshaft pulley puller. Used on pulleys with or without or without tapped holes. Works on many European & Asian vehicles. tapped holes. Universal application. Maximum Spread: 8.5/8"(220mm) Maximum Spread: 8.5/8"(220mm) TM


141

T

&E OOLS

ENGINE SERVICE TOOLS - HARMONIC BALANCER No.A1054-2 Universal Separator for Gears & Pulleys l

Short & Long Forcing Screws with Three Swivel Centre Caps. (Flat, Tapered Large, Tapered Small)

Multi-Purpose 6 Slots / 6 Studs

Extra heavy duty multi-purpose flange puller for removing harmonic balancers, pulleys, timing gears, etc. Applicable for Ford, Toyota, Mitsubishi, etc. Puller has a universal application wherever a short centre screw puller is required. 6 Slot Bolt Circle Diameter:

1.3/4" to 7.1/4"(45mm to 185mm) Weight: 1.5kg Harmonic Balancer Pullers & Replacers

No.9260

Universal Flange Puller Set

Two & three way flange plate with adaptors to pull harmonic balancers, steering wheels, flanges, etc. Includes short & long forcing screw. Bolt sets included: 3 of 3/8" UNC x 4" long 2 of 1/4" UNF x 3" long 3 of 3/8" UNF x 2" long 3 of 5/16" UNC x 2" long 3 of 8x1.25mm x 40mm long 3 of 5/16" UNC x 4.1/2" long 2 of 8x1.25mm x 65mm long 2 of 5/16" UNF x 3.1/2" long 3 of 8x1.25mm x 80mm long 3 of 3/8" UNC x 2" long 3 of 10x1.50mm x 50mm long Bolt Circle Diameters: 1.1/4" to 4.5/8"(32mm to 118mm)

No.T9516 Balancer Puller & Replacer 22mm Forcing Screw New Smaller Diameter Centre Screw to Fit Late Model Holden 3800 V6 Commodore Engines

Univseral Application with Needle Race Thrust Bearing

No.T9515 Balancer Puller & Replacer 13mm Forcing Screw

No.9262 50Pc. Harmonic Balancer Remover & Replacer Set includes nine complete sets of mounting bolts to fit most imperial & metric applications. Two size centre forcing screws with flat, large & small tapered forcing screw swivel caps. Eight imperial & metric threaded replacing adaptors, large hex forcing screw, nut & thrust bearing. Many jobs can be performed without removing the radiator. Bolt Circle Diameters: 1.1/4" to 4.5/8"(32mm to 118mm)

142

TM

Eight imperial & metric threaded adaptors, plus an end cap adaptor. Shouldered bolts to suit 3800cc V6 Commodore engines. The pulling plate, fitted with its needle race thrust bearing removes or replaces the pulley by the position of the thrust nut. Instruction included. Sets include: Adaptors: 7/16", 1//2", 9/16", 5/8" & 3/4" UNF

12 x 1.5mm, 14 x 1.5mm & 16 x 2.0mm Bolt sets included:

3 of 1/4" UNF x 2.1/2" long 3 of 5/16" UNF x 2.1/2" long 3 of 1/4" UNF x 3.1/2" long Bolt Circle Diameters: 1.1/4" to

3 of 3/8" UNC x 2.1/2" long 3 of 10mm x 1mm long 1 of Extension piece 2" long 4.5/8"(32mm to 118mm)


ENGINE SERVICE TOOLS - HARMONIC BALANCER No.9513 Universal Harmonic Balancer Puller Heavy-duty drop forged body pulls harmonic balancers, timing gears, flywheels, pulleys and parts having two or three tapped holes. Bolt Circle Diameters: 1.1/8" to 4.11/16"(28 to 120mm) Bolts Included: 3 of 5/16"UNC x 2" Long 2 of 3/8"UNC x 4" Long 3 of 3/8"UNF x 2" Long 2 of 10 x1.5mm x 50mm

No.J518 2/3 Way Flange Puller Set

T

&E OOLS

No.9514 Harmonic Balancer Replacer Set The built-in thrust assembly allows you to easily press the pulley back into place using a ratchet wrench on the large hex forcing nut. Many jobs can now be performed without removing the radiator. Installer supplied with eight imperial & metric adaptors. Adaptors: 7/16" x 20, 1/2" x 20, 9/16" x 18, 5/8" x 18, 3/4" x 16, 12 x 1.5mm, 14 x 1.5mm 16 x 2.0mm Forcing Screw Cap Fitted with Roller Bearing

No.J9260 Short Screw Harmonic Balancer Puller

Heavy-duty flange puller for use on harmonic balancers, timing gears and parts having two or three tapped holes. Slotted holes in puller work on bolt circle diameters: 1.1/2" to 4.5/8"(38 to 120mm) Bolt Sizes: 3 of 3/8"UNF x 3" Long 3 of 3/8"UNC x 3" Long

Short forcing screw & drop forged body gives access in confined areas. Can also be used on timing gears, flywheels, pulleys & parts having two or three tapped holes. Hex head screws with washers included

No.9526 Adaptor Set to suit Holden

3 of 5/16"UNF x 3"(76mm) 3 of 3/8" UNF x 3"(76mm) Bolt Circle Diameters: 1" to 3.3/4"(25mm to 95mm)

Bolt Sizes:

Shouldered bolts and adaptor for use with any flange puller for removal of harmonic balancer on GM 1990 - current 3.3L and 3.8L V6 engines. Bolt Lengths: 3.1/2" x 1/4"UNF

No.A7006 Universal Flywheel Holding Tool

No.9515 Commodore Harmonic Balancer Aligner l

Suits Commodore 3.8L V6 Engines

Enables crank angle sensor clearance to be preset, thereby eliminating damage when installing the balancer. Length: 4.3/4"(120mm)

No.9512 Harmonic Balancer Puller Suits GM V6 3800 Commodore

Harmonic balancer puller designed specifically for GM V6 3300 & 3800 commodore engines. The shoulder bolts are designed to prevent them from being installed too deeply, protecting crankshaft sensor or interrupter from damage. Fits: 1.1/4" to 4.5/8" bolt circle diameters.

This universal tool is bolted to the flywheel to lock it in place whilst using a torque wrench to tighten the centre screw. It prevents the transmission clutch spring & washer from rotating. Applicable for Honda, Ford, Mitsubishi, Toyota, etc.

No.9516 l

3 Spoke Harmonic Balancer Puller

Suits Chrysler, Mitsubishi, Ford & Holden V8's

Two size rods fit into forcing screw for different crankshaft lengths. Puller has 8 Ton capacity and the compact short legs in most cases eliminates the need for removal of the radiator & A/C condenser for access. Circle Diameter: 7"(180mm)

No.9512-B Bolt Set of Three for #9512 Work Safely With Hand Tools - Wear Safety Goggles TM

143

T

&E OOLS

ENGINE SERVICE TOOLS - TIMING CHAIN Suits Early Model Datsun & Nissan Engines

No.9517 Chrysler Harmonic Balancer Holding Tool

Designed as a holding ring with three pins that fit into the openings of the harmonic balancer. Use with a 1/2"Drive socket bar to hold harmonic balancer in place when tightening or loosening the crankshaft balancer bolt. Also used to hold the balancer when removing it from the engine. Circle Diameter: 5.3/8"(136mm)

No.4555 Nissan Timing Chain Holding Wedge Fits 1968 - 1979 1.6L & 2.0L four cylinder engines. Also fits 1970 - 1983 2.4L, 2.6L & 2.8L inline six cylinder engine on "Z" cars. Keeps timing chain from dropping inside timing cover while cylinder head or camshaft is removed. Length: 9.1/8"(232mm)

Suits Late Model Nissan Engines

No.6269 Volkswagen Camshaft Timing Tool Set

Used to retain and lock the camshaft timing when replacing the timing belt or servicing engine parts. Suits Volkswagen Bora, Golf, Lupo and Polo TDI's. Tool: 2.1/2" x 2"(64mm x 50mm) Pin: 3.3/8"(85mm)

No.J4936 Ford Timing Chain Tensioner Adjusting Tool Used for removal and installation of timing chain tensioners on Ford 3.9L & 4.0L 6 cylinder engines. Models EA Falcon and on. Pitch Circle Diameter: 1"(25mm) Pin Diameter: 3/16"(5mm) Hex Head: 3/4"(19mm)

41mm

No.4575 Nissan Timing Chain Holding Wedge Tapered wedge is used to keep timing chain from dropping inside timing cover while cylinder head or camshaft is removed. Safety hook supplied to prevent wedge from dropping inside the engine. Length: 4.7/8"(124mm) A

B

No.4935 Ford Timing Chain Adjuster

Used to remove tensioner and reset chain tension on Ford Falcon 6 cylinder engines. Models EA and on. Length: A 4.1/2"(114mm) Length: B 2"(50mm)

46mm

No.4936 Timing Chain Tensioner Tool Used on overhead cam engines with timing chains including: Mazda, Mitsubishi, Chrysler, Nissan, 1/2" Drive crowfoot wrenches give access to engine timing belt Toyota & most Asian vehicles. The tool holds the timing chain in tensioners on GM and Asian vehicles. Lengths: 3.1/2"(90mm) place while removing cylinder head, servicing camshaft gears, etc. lever designed tool applies smooth tension on timing chain. No.6265 41mm Timing Belt Tensioner 1.2L,1.3L, Cam The special long hook is required on some vehicles to release the 1.4L, 1.6L, 1.6D, 1.8L engines, '87 and onwards chain tensioner. O-ring on adjustment nut holds socket onto tool. Eliminates using bulky wood blocks which obstruct cylinder head No.6267 46mm Timing Belt Tensioner removal. Length: 10.3/8"(264mm) Hook Length: 16.1/2"(420mm) 1.6L, 1.7D, 1.8L, 2.0L engines, up to '87

Engine Timing Belt Tensioner Adjusters

No.4948 Toyota Timing Belt Tensioner Compressor For 1995 and later T-100, Tacoma, and 4Runner. Turn square to compress tensioner, then install locking pin. Lengths: 5.1/2"(140mm)

144

TM

No.6466 3-in-1 Bosch Timing Tool M8, M10, M12 Combination tool suitable for use on Bosch VE type fuel injection pumps and also for new pump with M10 service port. Also fits Kiki and Nippon Denso pumps. Includes adaptors and control rods. Adaptors supplied with 8mm threads plus M10 and M12 adaptors. M10 adaptor is new and is suitable for service ports commonly found on VW/Audi, Volvo, Renault and Ford Transit.


ENGINE SERVICE TOOLS - TIMING & CAMSHAFT No.4096 TDC Timing Degree Wheel

360° Timing Degree Wheel is designed for finding top dead centre and checking camshaft timing. Three holes allow the wheel to securely fasten to the engine crankshaft. Use in conjunction with a dial gauge or #4749, #4750 Piston Locating Tool for correct intake and exhaust valve timing settings. Diameter: 12.5/8"(320mm)

T

&E OOLS

Suits: 4.6 Litre 5.4 Litre V8 Engines & 6.8 Litre V10 Engines

No.4924C

Ford Cam Positioning Tool

For setting the camshaft timing on 1991 thru to current 4.6 litre twin valve engines, 5.4 litre V8 & 6.8 litre V10 engines. Two locking plates & two cam positioning tools that install onto the camshaft to prevent it from rotating when adjusting the cam timing. Length: 8.1/4"(210mm)

No.6268 Mazda / Ford Engine Locking Plate Locking plate for camshaft setting. Suits Ford 1.6L, 1.8L & twin cam 16 valve petrol engines. Used for finding crankshaft TDC location on Ford 1.3L & 1.4L engines plus Puma1.7L engines. Use with TDC pin for Mazda 121, 1.3L petrol engines. Supplied with warning tag. Length: 8.3/4"(222mm)

No.98700 Mitsubishi / Hyundai / Chrysler Timing Belt Tensioner Allows for easy adjustment of the camshaft spur belts having idler pulleys with pin holes. Protruding pins grip the centre of the idler pulley and rotate it around its off-center retaining bolt. This rotation then allows for camshaft spur belt tension adjustment. 1/4"Drive for use with torque wrench. Made from heat treated alloy steel. Pin Dia: 3/16"(5mm)

No.4287 Camshaft Locking Bar Set

Camshaft setting and locking plate with timing pins. Suits Zetec engines found in Ford Focus, Mondeo & Cougar from 1998 to current. Also covers Ford 1.6L, 1.8L & twin cam 16 valve petrol engines. Crankshaft TDC locator for Ford 1.25L & 1.4L engine plus the Puma 1.7L engine. TDC pin also supplied for Mazda 121 1.25L petrol engines. Supplied with warning tag. Length: 8.3/4"(222mm)

No.6282 Holden / Astra / Opel Twin Cam Locking Tool For Twin Cam ECOTEC 16v Engines

The twin cam locking tool acts as a second pair of hands, helping to retain camshafts in their timing position to ensure the engine timing is retained during timing belt removal & renewal. Suit the Holden Astra / Opel ECOTEC 16 valve 1.8L engines. Length: 2.1/2"(64mm)

No.6275 4 Pin Twin & Quad Cam Locking Tool No.6273 Mercedes Benz Camshaft Alignment Tool

Holds the camshaft at 40° to TDC position for both Left and Right hand side. Suit: Mercedes C, E, S, SL, M-Class, SLK, G-Wagon. Length: 11.1/2"(292mm)

Retains camshafts in their timing position to ensure the engine timing is retained during timing belt removal & renewal. Use also on diesel engines which have their cam & injection pump sprockets in close location. Can be used the same way to retain diesel timing position. Dimensions: 3.1/2" x 4.3/4"(89mm x 120mm) Adjustable

No.6266 Twin & Quad Cam Locking Tool

Adjusts from 100 to 220mm

No.A2123 Universal Camshaft Alignment / Locking Tool Use sockets to lock onto camshaft central screw. Adjustable to fit most twin camshafts. Special design aligns and locks camshaft for removal or installation of the cylinder head guide rail pins. TM

Suits Twin Cam & Quad Cam Engines

The twin cam locking tool acts as a second pair of hands, helping to retain camshafts in their timing position to ensure the engine timing is retained during timing belt removal & renewal. Use also on diesel engines which have their cam and injection pump sprockets in close location. The locking tool can be used the same way to retain diesel timing position. Dimensions: 3.1/4" x 4.1/2"(82mm x 115mm) Adjustable


145

T

&E OOLS

ENGINE SERVICE TOOLS - TIMING & CAMSHAFT

No.6276 GM Diesel Engine Camshaft Locking Tool

No.6274 Audi / VW Camshaft Locking Tool

Specially designed for locking Suitable for VW / Audi 1.4 / 1.6L petrol engines. e.g. VW Lupo, Polo, camshaft on later model General Motors Golf IV, Bora, Audi A2. Locks timing gears during engine repairs. diesel engines. Length: 5" x 2.1/4"(127mm x 57mm) Diameter: 4.1/8"(105mm)

No.A1136 BMW Camshaft Alignment Tool

A1019

A1021

Includes inlet and exhaust camshaft gauges, bracket with bolt, camshaft alignment pin applicable to BMW N62 & N73 engines.

A1033

No.A1156 BMW Camshaft Alignment Tool

No.A1088 BMW Camshaft Alignment Tool Kit Camshaft alignment tool kit comprises of blocks, locking plates and pins for setting camshaft timing on BMW models M40 to M70. Contains: A1033 Timing Blocks & Pin To suit BMW M42 & M50 A1021 Timing Blocks & Pin To suit BMW M60 & M62 A1019 Timing Plate & Pin To suit BMW M40 & M70

This tool is a gauge for fixing the camshaft in TDC position. Use to dismantle and assemble intake and exhaust camshafts. Applicable BMW N42 & N46 engines. Suits: Ecotec V6 Multi-Valve Engines General Motors Opel & Vauxhall

No.6289 Audi Cam Alignment Tool

Special tool designed to lock the camshaft into position to prevent it from rotating when adjusting cam timing. Suits: Later model Audi vehicles

No.6279

Engine Timing / Locking Tool Set

Camshaft Timing Gauge Right Hand Camshaft Locking Tool (red) Left Hand Camshaft Locking Tool (green) Contains:

Crankshaft Locking Tool Belt Holding Wedge

No.6280 8Pc. Camshaft Timing Lock Tool set 8Pc set used to retain and lock the camshaft timing when replacing timing belt or servicing engine parts. Set contains: #6281 thru to #6287 as listed in table below. Individual Sizes:

Part No 6281 6282 6283 6284 6288 6285 6286 6287

146

6281

6282

6283

6284


Description

Timing Timing Timing Timing Timing Timing Timing Timing

Locking Tool Locking Tool Locking Tool Locking Tool Locking Tool Locking Tool Locking Tool Locking Tool TM

Application Vectra / Astra / Vauxhall Holden / Astra / Opel Saab / Vauxhall / Opel Saab / Vectra / Opel Rover / BRM / MGF VW, Bora, Golf, Polo, Passat Citroen / Peugeot / Fiat / Ford Isuzu & Vauxhall diesel engines

6288

6285

6286

6287


ENGINE SERVICE TOOLS - GENERAL No.4960 Timing Belt Pulley Rotating Tool

T

&E OOLS

Fit belt between the two grooves to easily rotate the engine with the leverage supplied by the extra long handle. Groove Opening: 3/8"(10mm) Length: 13.3/8"(340mm)

No.J9955 Oil Pan Separator Tool

No.4943 18mm Engine Mount Crowsfoot Wrench

Wide tapered, ground blade wedges between metal surfaces to break gasket seals on engine sumps, transmissions, or any difficult to separate gasket joints. Blade Width: 1.7/8"(48mm) Length: 3.1/8"(80mm)

Designed for quick R&R of the front motor mount on late model Ford vehicles. This new time saving tool turns a 2-3 hour motor mount replacement job into about a 20 minute process. Size: 18mm x 12Pt x 1/2"Square Drive Length: 13"(330mm)

Suits Serpentine Belt Pulleys

Ensures Oil is Present to Internal Engine Components on the First Start of a New or Rebuilt Engine

No.J1810 Universal Grooved Pulley Puller Set

No.2-6492 New Engine Pre-lube Pump

Puller has four sets of interchangeable and adjustable legs to pull most ribbed and groove type engine pulleys fitted to late model engines. Suitable for use on crankshafts, alternators, air conditioning compressors and water pump grooved pulleys. Maximum Spread: 7.3/4"(195mm)

Engine pre-lube pump primes the oil pump and fills the oil galleries and internal engine components with clean new oil. Pump connects to engine at the oil pressure sensor on most Australian and import engines. Oil pressure sensor adaptors are included to suit most engines. Capacity: 2.5 Litres

Removes & Inserts Camshaft Bearings in all Engines from Compact Cars to Heavy Trucks

No.J1800

Universal Cam Shaft Bearing Tool

The expander has a neoprene sleeve over which the split driving plugs are mounted and expanded to size. This tool has two sets of rubber sleeves supplied with it for each expanding driver. The brown sleeves are used when driving thin wall bearings (.065"). The black sleeves should be used when driving thick wall bearings (.090"). Range: 1.1/8" to 2.11/16"(28 to 68mm)

Bar Length: 28.1/2"(724mm) Part No. No.J1800-1 No.J1800-2 No.J1800-3 No.J1800-4 No.J1800-5 No.J1800-EXA No.J1800-Black No.J1800-Brown

Description #1 Expanding Driver #2 Expanding Driver #3 Expanding Driver #4 Expanding Driver #5 Expanding Driver Expander Unit Black Sleeve Set Brown Sleeve Set

Bottle Brush Cylinder Ball Hones Available in 180 Grit Medium & 240 Grit Fine Use with light grade oil only. Hone and remove glaze from cylinders with flexible stone type abrasive ball ends. Ball ends create a perfect cross hatch pattern to enable piston rings to bed correctly against cylinder walls. Available in sizes listed in tables below. Brush Lengths: 3"(76mm)

Cylinder Brush Ball Hones - Medium Grit: Part No. FBH101-1 FBH102-1 FBH103-1 FBH104-1 FBH105-1 FBH106-1 FBH107-1 FBH108-1 FBH109-1 FBH110-1 TM

Grit 180 grit 180 grit 180 grit 180 grit 180 grit 180 grit 180 grit 180 grit 180 grit 180 grit

Size Inch 2.1/2" to 2.1/4" 2.3/4" to 2.1/2" 3" to 2.3/4" 3.1/4" to 3" 3.1/2" to 3.1/4" 3.3/4" to 3.1/2" 4" to 3.3/4" 4.1/4" to 4" 4.1/2" to 4.1/4" 5" to 4.1/2"

Size mm 64 to 57mm 70 to 64mm 76 to 70mm 83 to 76mm 89 to 83mm 95 to 89mm 102 to 95mm 108 to 102mm 114 to 108mm 127 to 114mm

Cylinder Brush Ball Hones - Fine Grit: Part No. FBH101-2 FBH102-2 FBH103-2 FBH104-2 FBH105-2 FBH106-2 FBH107-2 FBH108-2 FBH109-2 FBH110-2

Grit 240 grit 240 grit 240 grit 240 grit 240 grit 240 grit 240 grit 240 grit 240 grit 240 grit

Size Inch 2.1/2" to 2.1/4" 2.3/4" to 2.1/2" 3" to 2.3/4" 3.1/4" to 3" 3.1/2" to 3.1/4" 3.3/4" to 3.1/2" 4" to 3.3/4" 4.1/4" to 4" 4.1/2" to 4.1/4" 5" to 4.1/2"

Size mm 64 to 57mm 70 to 64mm 76 to 70mm 83 to 76mm 89 to 83mm 95 to 89mm 102 to 95mm 108 to 102mm 114 to 108mm 127 to 114mm


147

T

&E OOLS

ENGINE SERVICE TOOLS - SENSOR SOCKETS

No.5569 Distributor Adjusting Screwdriver

Extra long 3mm In-Hex screwdriver for adjusting distributors etc. on later GM and Ford vehicles. Size: 3mm In-Hex Length: 12"(305mm) Opening: 7/8"(22mm) Single hex

No.4013 Vacuum Switch Socket 7mm Slot allows socket to fit over the connectors on vacuum switches. Universal applications for most vehicles. Made from heat treated alloy steel. Drive: 3/8"Square Size: 7/8"(22mm) Length: 2.3/4"(70mm)

1/2"Drive Heavy-Duty

No.4112 Oxygen Sensor & Vacuum Switch Socket

Socket removes & replaces PVS & TVS valves vacuum switches & oxygen sensors on vehicles with computerized engine management systems. Socket incorporates slot for sensor wire clearance. Made from alloy steel. Drive Size: 3/8"Square drive internal 7/8"(22mm) Hex external Length: 3.1/2"(90mm)

No.2-7231 Oxygen Sensor Socket

Works on all domestic & imported vehicles with oxygen sensors. Slot in socket's side allows for wire clearance. The outside rib gives added strength, yet doesn't restrict access to sensors. Size: 7/8"(22mm) Single hex 1/2"Square Drive Length: 4"(100mm)

See Page 186 for Additional Disel Injector Sockets

12

No.4595 Coolant Temperature Sensor Socket

Fits Nissan cars & trucks with 3.0L V6 engines. For easy removal and installation of coolant temperature sensors. Size: 19mm 12 Point x 3/8"Square Drive Length: 1.5/8"(42mm) Depth: 1"(25mm)

11

10 3

13

Special 6 point split offset crowsfoot socket for replacing lambda probes. Universal application suits most engines including Ford, BMW, OPEL, VW / AUDI, etc. Size: 7/8"(22mm) Single Hex 1/2"Drive Length: 2.3/4"(70mm) Depth: 1.3/16"(30mm)

148

TM

8

5

2

9 1

6

14

7

No.J4295 Injector & Sensor Switch Socket Set Master set of fourteen 1/2"Drive injector & sensor switch sockets that feature special cut-away in the deep wall to allow access to remove & replace injectors without damaging fuel lines. Set Contains fourteen specialty sockets that fit injectors on most diesel engines including: VW, Audi, Opel, GM, BMW, Ford, Mercedes, Volvo, Rover, Seat, Chrysler, Alfa Romeo, MAN, etc. Set is supplied in blow mold case. Individual Sizes:

No.4094 Open-End Hexagon Socket for Lambda Probes

4

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Part No 4031 4032 4033 4034 4035 4036 4037 4025 4038 4039 4040 4041 4110 4109

Drive 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 3/8" 3/8"

Size 17mm 19mm 20mm 21mm 22mm 22mm 22mm 27mm 27mm 27mm 28mm 30mm 7/8"(22mm) 7/8"(22mm)


Description 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 6Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 6Pt. Open Split Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket 12Pt. Open Side Sensor / Injector Socket Offset Oxygen Sensor Wrench Shallow Offset Oxygen Sensor Wrench

Length 80mm 80mm 80mm 80mm 80mm 110mm 150mm 80mm 110mm 80mm 80mm 80mm 85mm 60mm


ENGINE SERVICE - SENSOR SOCKETS & CHASERS No.4014 14mm Oil Pressure Sending Unit Wrench

T

No.4017 17mm Oil Pressure Sending Unit Wrench

For easy removal and replacement of oil pressure sending units without removing the manifold. For use on oil pressure sending units on vehicles equipped with an oil pressure gauge. Opening: 14mm Open End x 3/8"Drive Length: 4"(100mm)

For easy removal and replacement of oil pressure sending units without removing the manifold. For use on oil pressure sending units on vehicles equipped with an oil pressure gauge. Opening: 17mm Open End x 3/8"Drive Length: 4"(100mm)

No.4012 Dual Size Oil Pressure Switch Socket

No.4113 1.3/16"(30mm) Oil Pressure Sending Switch Socket

Specially designed and shaped dual sized socket to fit most oil pressure switches on vehicles equipped with warning lights. Use with a 3/8"drive socket bar or a 7/8"wrench. Dual Openings: 1"(25mm) & 1.1/16"(27mm) Length: 2.1/8"(55mm) Extra Deep 93mm Long!

No.4019 1" & 1.1/16" Deep Oil Pressure Switch Socket

Specially designed and shaped dual sized deep socket to fit most oil pressure switches on vehicles equipped with warning lights. Use with a 1/2"drive socket bar. Dual Openings: 1"(25mm) and 1.1/16"(27mm) Length: 3.5/8"(93mm)

No.4490 18 x 1.5mm Oxygen Sensor Thread Chaser Cleans threads in oxygen sensor holes. Use with 3/4" hex socket or 3/8" square drive. Size: M18 x 1.5 Also works on 18mm spark plug threads Length: 2"(98mm) IMPORTANT: Use anti-seize

No.4492 2Pc. Lambda Sensor Thread Chaser Used to repair damaged lambda-probe mounting threads on the manifold when exchanging the lambda-probe. Includes:

18 x 1.5mm Thread Restoring Tap 12 x 1.5mm Thread Restoring Tap Length: 2"(50mm) IMPORTANT: Use anti-seize TM

&E OOLS

For late model GM's with oil pressure sending units on vehicles equipped with dash gauges. The sending unit is approximately 3.1/4" long and cannot be reached with deep sockets. Length: 3.1/2"(90mm) x 3/8"Drive

No.4110 Offset Oxygen Sensor Wrench l

Works in The Most Confined Spaces

This wrench has been designed for use with most all oxygen sensors no matter what size electrical connectors they have. Easily removes the oxygen sensor located in the exhaust manifold. Size: 7/8"(22mm) Single hex 3/8"Square Drive Length: 3.1/2"(83mm)

No.4109 3/8"Drive Short Oxygen Sensor Wrench This wrench has been designed for use with most all oxygen sensors no matter what size electrical connectors they have. Easily removes the oxygen sensor located in the exhaust manifold. Size: 7/8"(22mm) Single Hex Length: 2.1/8"(54mm)

No.B1145 Forged Oxygen Sensor Socket

22mm Double Hex

Fully forged & reinforced body to remove the most stubborn oxygen sensors 26.5mm without rounding off. The flare nut type 12 point 22mm double hex opening with an 8 point 3/8" drive for servicing the vacuum switch & oxygen sensor on computer controlled engines. Length: 3.5/8"(93mm)


8 Point 3/8"Drive

149

T

&E ENGINE SERVICE - OIL PUMP & TIMING HOLDING TOOLS OOLS IMPORTANT: Use anti-seize

A

B F

C

E

D G

No.J4298 Injector / Sensor Switch Socket Set

Injector & Sensor sockets: D) #4019 1 & 1.1/16" Oil Switch Skt A) #4042 29mm Sensor Skt, E) #4013 22mm Sensor Skt B) #4112 22mm Vacuum Skt, F) #4110 7/8" Offset Sensor Skt C) #4038 27mm Injector Skt, G) #4109 7/8" Offset Sensor Skt

No.4920 3Pc. Oil Pump Primer Set Oil pump primers protect new and rebuilt engines from premature wear caused by a dry start. Set includes #4923, GM V6 and V8 engines. #4921 1/4"Hex, #4922 5/16"Hex Ford oil pump primers. Lengths: 9.3/4"(248mm)

No.4949A BMW Visco-Fan Reaction Wrench Used to provide a reaction point to dismantle Visco-Coupled cooling fan on BMW 4-cylinder and 6-cylinder diesel engines. Hole Distance: 1.3/4"(44mm) Length: 16"(406mm)

No.4949B BMW Visco-Fan Reaction Wrench Used to provide a reaction point to dismantle Visco-Coupled cooling fan on BMW 4-cylinder and 6-cylinder diesel engines. Hole Distance: 1.1/2"(38mm) Length: 16"(406mm)

IMPORTANT: Use anti-seize


Use with an Electric Drill


No.4922 Ford Oil Pump Primer 5/16"Hex

Use primer to protect a freshly rebuilt or modified engine from premature wear caused by a dry start. Design includes a machined aluminium collar that simulates the distributor and helps to eliminate damaging side loading of the oil pump drive while priming. Length: 9.3/4"(248mm)

No.4921 Ford Oil Pump Primer 1/4"Hex

Use primer to protect a freshly rebuilt or modified engine from premature wear caused by a dry start. Design includes a machined aluminium collar that simulates the distributor and helps to eliminate damaging side loading of the oil pump drive while priming. Length: 9.3/4"(248mm)




Use with an Electric Drill No.4923 GM V6 & V8 Oil Pump Primer

Use primer to protect a freshly rebuilt or modified engine from premature wear caused by a dry start. Design includes two machined aluminium collars that simulate the distributor and helps to eliminate damaging side loading of the oil pump drive while priming. Length: 9.3/4"(248mm)

150

TM

No.4959 Oil Pump Screen Installer

Special tool designed for installation of oil pump screens fitted to many engines having a standard size pickup screen tube. Prevents damage of difficult to fit oil pump screen tubes. Length: 8.3/4"(222mm)

No.4926 Timing Adjustment Holding Tool

VW, Polo, Beetle, Golf Bora Length: 30.1/4" (770mm)

No.4927 Timing Adjustment Holding Tool

VW, Polo, Beetle, Golf Bora Length: 27.1/2" (700mm)


ENGINE SERVICE TOOLS - ENGINE LIFTING No.4026 FWD Engine Tilting Tool Fits front wheel drive vehicles with engine torque struts used on most transverse mounted engines. Replaces existing torque strut dog bone and allows the engine to be tilted forward. Provides easy access to spark plugs, distributor caps, ignition coils, rack and pinion steering gear, power steering hoses, etc. located between engine and engine firewall. Safely holds engine in place while working in confined areas. Made of high strength heat treated alloy steel. Multiple bolt holes provide fit on most vehicles. Length: 7"(178mm)

No.2-1805 2000lb Load-Rotor Positioning Sling Engines, transmission, etc. can be leveled whilst lifting by turning the 5/8" hex drive end with a socket or wrench. Forged swivel hooks at each end with brackets. Capacity: 2000lb(900kg) Chain: 1/4" Diameter Length: 56.1/2"(2.2m)

No.2-1806 4000lb Load-Rotor Positioning Sling

Engines, transmission, etc. can be leveled whilst lifting by turning the 5/8" hex drive end with a socket or wrench. Forged swivel hooks at each end with brackets. Capacity: 4000lb(1800kg) Chain: 5/16" Diameter Length: 66"(1.7m)

T

&E OOLS

No.4340 Engine Lifting Chain l

Capacity: 1/2 Ton(500kg)

For easy lifting and removal of automotive engines, transmissions or other heavy units. Easily adjustable for proper balance. Keyhole loop provides exclusive Link-Lock feature assuring safe lifting. Half ton load tested 28"(70cm) chain and lugs are made from heat treated alloy steel. Length: 32"(812mm) No.2-1805 2000lb(900kg) Capacity No.2-1806 4000lb(1800kg) Capacity

No.B7100 Engine Lifting Brackets This pair of lifting brackets with 1/2"(13mm) holes, bolt directly to the component for easy lifting. The large chain links make hook-up a simple and secure operation. Hole Diameter: 1/2"(13mm) Lifting Capacity: 4000lb(1800kg)

No.4300 Heavy-Duty Adjustable Sling For lifting and positioning engines, transmissions, etc. Each chain can be adjusted independently for length. plate design enables chain to be "short-hooked" for correct tilt. Heavy duty safety hooks are fitted to both ends. Capacity: 4000lb(1785kg) Chain: 5/16"(8mm) Diameter Length: 65"(1.6m)

No.ES1500 1500lb Engine Stand Overhaul and repair of engines can be performed with speed when the unit is conveniently held and positioned at work bench height. An engine can be rotated a full 360° with an easy turn of the handle. Locking pin secures work at different positions. Smooth rolling wheels and swivel casters provide ease of mobility. Capacity: 1,500lb(680kg) Suitable for Passenger Car & Light Commercial Truck Engines Weight: 44.5kg TM

No.EH2202A Transverse Engine Support Bar

For use when undertaking sub frame and suspension repairs, servicing gear boxes etc. Avoids tying up expensive lifting equipment when awaiting for replacement parts. Rubber feet protect paintwork and are adjustable to any angle. Heavy-duty double box frame construction. Maximum Span: 5ft.3"(1.6m) Maximum Load Capacity: 500kg

No.A1117 Gear Type Universal K/D Rack

Universal engine stand features a gear type drive that allows the engine to rotate 360° to offer every angle of position for engine maintenance. Four wheels with brake mechanism make it stable during engine or transmission overhaul. Size: 1.145m L x 1m W x 0.92m H Capacity: 1500lb(680kg) Optional:

A1117-2 Slop Oil Pan Size: 1010mm x 1020mm

Size: 1010mm L x 850mm W x 1000mm H


151

T

&E OOLS

ENGINE FAN SERVICE TOOLS Ford Fan Clutch Tool Sets

Consists of two extra slim wrenches and holding device for removal and replacement of the viscous fan clutch assembly on Ford Falcon, Fairlane, etc. Suits both 6 & 8 cylinder engines. Elongated slots in holding bar hold firmly on three stud heads. The 32 x 36mm wrenches are offset to give knuckle clearance. Short Handle Wrenches Offset

Long Handle Wrenches Straight

Clutch Assembly

No.4938-S Ford Fan Clutch Tool Set

No.4938-L Ford Fan Clutch Tool Set

Short Handle Wrenches Offset

Long Handle Wrenches Straight

No.4938-1 Ford Viscous Fan Wrench Set Offset

No.4938-3 Ford Viscous Fan Wrench Set Long

Contains: 32mm and 36mm Offset wrenches. Universal holding tool. Contains: 32mmand 36mm Straight wrenches. Universal holding tool. Length: Wrenches 11"(280mm) Holding Tool: 17.3/4"(450mm) Length: Wrenches 15.1/4"(385mm) Holding Tool: 17.3/4"(450mm)

32mm Offset wrench for 6 cylinder Ford. 36mm Offset wrench for 8 cylinder Ford.

Lengths: 11"(280mm)

32mm Long straight wrench for 6 cylinder Ford. 36mm Long straight wrench for 8 cylinder Ford. Lengths: 11"(280mm)

Clutch Holding Tool to Hold Fan Clutch Stationary Use Wrenches to Turn Fan Clutch Nut

No.J2090 U.S. Ford Viscous Fan Wrench & Holder

No.4938-2 Ford Viscous Fan Holding Bar

For the removal of Thermo-Viscous fans on U.S. Ford, BMW and Elongated slots fit over and grip firmly on three of the stud heads other vehicles. holding the viscous fan clutch assembly. Length: 17.3/4"(450mm) Wrench Opening: 36mm Holding Bar Opening : 2.5/16"(59mm)

No.4939 Fan V-Belt Tension Gauge No.4937 Fan V-Belt Installer & Remover l Safe, Fast & Convenient Keeps hands away from moving parts. Steel and neoprene tool derails and installs V-belts quickly and safely. Eliminates loosening bolts or stretching belts. Designed for use with #3554 Remote Starter Switch for maximum safety. Length: 3.1/2"(89mm)

No.4940

Gauge measures and shows when V-belt is at proper tension. Properly tensioned belt maximizes belt life, increases engine efficiency and assures minimum wear on parts. Complete instructions included in package. Length: 3.1/2"(89mm)

Serpentine Belt Wrench Kit

This Serpentine Belt Wrench Kit is designed to release the tension on spring loaded idler pulleys. These tools allow direct access to the tensioner without having to remove engine accessories or frame components. Ratcheting wheel allows quick and easy positioning of the wrench driving end to allow the user to access the tensioner from any angle. The universal two wrench kit will service 90% of all vehicles with spring loaded tensioner pulleys. Set contains:

No.4941 No.4942

Serpentine Belt Wrench 13mm, 14mm, 18mm 1/2"Drive Length: 15"(385mm) Serpentine Belt Wrench 15mm, 16mm, 3/8" 1/2"Drive Length: 15"(385mm)

No.4945

"Belt-It" Belt Installation Tool

This time saving tool gives the technician the control and reach when installing serpentine belts in all applications. The tool was also designed to help install V-belts and timing belts that tend to be placed in areas that are difficult to reach. The two pin design gives the technician convenient belt push/pull capability and the handle gives the technician the twisting control to install belts in difficult areas. Length: 24"(610mm)

152

TM


ENGINE FAN SERVICE TOOLS

No.J4105

T

&E OOLS

14Pc. Serpentine Belt Tool Set

This set provides the required leverage and clearance to release spring tension on the tensioner pulley to remove & replace almost inaccessible serpentine belts. Set Includes: One: Long Handle 18"(460mm), Two: Handle Extensions 4"(100mm), 6"(150mm), Two Square Drive Adaptors: 3/8" & 1/2" Three Crowsfoot Wrenches: 13, 14, 15mm, Five Shallow Sockets: 13, 14, 15, 16, 18mm One: 3/8" x 16UNC Fixing Bolt

No.91210 Nissan / Mercedes / Mercury Fan Belt Wrench Special hex-key wrench with 1/2"drive adaptor, used for loosening the quest air conditioner idler pulley tensioner lock-nut for A/C belt adjustment or replacement. Length: 19"(485mm)

No.A1022B BMW Viscous Fan Pulley Holder Dual size holding tool used to provide a reaction point to dismantle Visco-Coupled cooling fan on BMW 4-cylinder and 6-cylinder diesel engines. Hardness: HRC 40°- 45° Length: 15.3/4"(400mm)

65mm Opening

No.J6263 Mercedes Benz Viscous Fan Hub Wrench Special 65mm open end wrench used for the removal and replacement of the radiator fan hub on Mercedes Benz engines. Suits: M103 - 6 cylinder, M104 - 6 cylinder 24 valve M119 - 8 cylinder 32 valve M120 - 12 cylinder 48 valve Length: 15.3/4"(400mm)

No.4946 BMW / Ford / Opel Viscous Fan Holding Tool Essential tool to prevent fan hub from rotating when removing retaining nut. Unique swivel locking head for universal applications. Suits: BMW 316, 520, 525, 530, 730 & 735 Ford: Capri, Sierra, Granada, Vauxhall, Opel, Carlton, Manta, Senator Length: 16"(406mm)

Suits 4 Cylinder "E" & "C" Class Mercedes Engines M111

No.J4262 Mercedes Benz Viscous Fan Reaction Wrench Required to remove the radiator fan hub. The reaction wrench is bolted to the front face of the hub. Use when the pulley V belt is not in place and cannot be used to lock the hub. Hole Diameter: 11.7mm Length: 15.3/4"(400mm)

No.J4938 GM Fan Clutch Wrench

This specially designed tool is used to loosen and tighten the fan clutch on 1996 and later GM trucks and vans. The unique design works with both 10mm & 13mm pulley bolt heads. The tool enables the mechanic excellent control to hold the water pump pulley stationary while using an open end wrench to loosen the fan clutch. Length: 16"(406mm)

No.4938-5 2 Way Viscous Fan Wrench For removal of Thermo-Viscous fans on BMW, Ford, Opel, Mercedes. Sizes: 32mm & 36mm Length: 13" (330mm) TM

No.2-6068 Ford Diesel Fan Clutch Wrench

Has a 1.7/8"(48mm) opening with special offset handle for use on the viscous fan lock-nut fitted to Ford vans and pickups with 7.3 Litre direct-injected turbo charged (DIT) diesel engines. 1/2"Drive fitted to the end of the wrench for extra leverage. Length: 14.1/4"(360mm)

No.J4263 Mercedes Benz Viscous Fan Reaction Bar This tool allows the removal and replacement of the viscous coupling on the cooling fan fitted to Mercedes Benz engines. Length: 11.1/4"(285mm)

No.4933 Bussab Quest Fan Belt Service Wrench Special designed wrench for adjusting the fan belt on Nissan, Bussab Quest. Length: 9.3/4"(248mm)


153

T

&E OOLS

ENGINE FAN SERVICE TOOLS

No.4934 10Pc. Viscous Fan Clutch Wrench Set Set includes five wrenches and five holding tools to give a broad coverage of GM, Ford, Chrysler and other vehicles that use a fan clutch. Wrenches will reach into confined quarters to get the job done heat treated to withstand high toque needed to remover fan clutches. 1/2" square drive enables use of breaker bar to apply extra torque.

No.J7017 Fan Belt Tightening Tool

Holding Tool Sizes:

1.7/16"(36mm) Open End 1/2" Drive 2.1/8" (54mm) Open End 1/2" Drive 2.1/4" (57mm) Open End 1/2" Drive 2.3/8" (60mm) Open End 1/2" Drive 3" (76mm) Open End 1/2" Drive 3.1/4" (82mm) Open End 1/2" Drive

Wrench Sizes:

1.7/16" (36mm) Open End 1/2" Drive 1.9/16" (40mm) Open End 1/2" Drive 1.7/8" (48mm) Open End 1/2" Drive 2.13/16"(72mm) Open End Wrench

Makes belt tightening an easy one person job. Works on most alternators and some other belt driven accessory units. Drive: 1/2"Square Length: 8.1/4"(210mm)

No.J6265 Mercedes & BMW Fan Service Wrench Kit

10Pc. Set includes all the wrenches and holding tools for removal and replacement of lock nuts on thermo viscous fans found on Mercedes-Benz, BMW, Ford and many other vehicles. Made from heat treated alloy steel to enable the wrenches to be thin yet strong enough to handle the toughest job. Wrench Sizes:

65mm, 32mm, 36mm, 40mm Wrenches All 15"(380mm) Long with 1/2"Drive 8mm Hex Key Wrench 8mm & 10mm In-Hex Wrenches Mercedes Benz Reaction Bar.

No.7522 V-Belt Pulley Holding Tool Ideal for removing and installing any type of groove pulley. Adjustable notch V type belt, securely holds pulley from rotating whilst undoing fasteners. Maximum Capacity: 8"(200mm) Diameter Length: 20"(508mm)

No.J4266 Reaction Wrench VW, Golf, Passat, Audi Reaction wrench is used to lock the pulley on the water-pump on VW Polo, Golf, Passat & Audi 80/A4. 1/2" Drive in the tools handle enables further extension to be used. Length: 10"(255mm)

154

TM

No.4939-A Fan V-Belt Tension Gauge Designed for tensioning drive belts on passenger cars, light and heavy trucks. Correct tension levels are important in maintaining belt life and performance. Easy to use, just hold against the back of belt and click. Instructions included with product. Length: 4.5/8"(117mm)

No.4939-B Fan V-Belt Tension Gauge ( for Notched Belts )

Designed for tensioning notched drive belts on passenger cars, light and heavy trucks. Correct tension levels are important in maintaining belt life and performance. Easy to use, just hold against the back of belt and click. Instructions included with product. Length: 4.3/4"(120mm)

No.J4265 Reaction Wrench VW, Audi Reaction wrench is used for locking of deep-drawn water-pump pulleys on VW and Audi engines, as used when air conditioning is also built in. Diameter: 2.1/2"(65mm) Length: 12"(305mm)


T

&E OOLS

ENGINE - EXHAUST SERVICE TOOLS No.7706 Exhaust & Tailpipe Stretcher Pipe stretcher is a convenient, inexpensive alternative to hydraulic pipe expanders. Stretches all types of exhaust pipe including stainless steel. Use with impact wrench to quickly stretch pipes for connection. Two collet sets fit pipes from 1.5/8" to 2.1/2" Can be used on the car. Length: 7.1/2"(190mm)

No.7715 Exhaust Doughnut Removing Pliers Removes exhaust systems from rubber style hangers on tailpipes, intermediate pipes and mufflers. Features self-locating forcing pin, and "cushioned", slip-resistant handles at 25 degree offset for easy access in restricted areas. Length: 11"(280mm) Adjustable Three Rollers for Service on Both Large & Small Diameter Exhaust & Tail Pipes

No.7718 Exhaust Doughnut Hook Puller Set Removes and replaces rubber ring style hangers used on late model cars. Simply hook tool through rubber mounting ring and stretch until released from hook on muffler, pipe or frame. Reverse procedure for installation. Length: 8.3/4"(220mm)

No.7702 Exhaust Tailpipe Reshaper Reshapes damaged exhaust pipe ends in seconds, remove clamp grooves, round out crushed or bent pipes to assure a tight fit eliminating exhaust leaks. Three expanding rollers makes this frustrating job easy requiring only a 70 degree turning circle to remove grooves and restore the exhaust tailpipe shape. Capacity: 1.5/8" to 3.1/16"(41 to 78mm) Length: 10.1/2"(266mm)

No.7719 Exhaust Spring Clamp Remover / Installer Essential for safe, controlled removal of clamps attaching exhaust to manifold. Special design provides leverage required to expand the strong spring steel clamps. Length: 6"(150mm) Application: VW, Audi

No.WH707B Exhaust Fume Extractor Air operated exhaust fume extractor is designed to operate in any workshop and is ideal alternative to fixed, space consuming, expensive systems. Suitable for use on cars, vans, motorcycles, and light commercials, it allows the garage mechanic to work on the vehicle with the engine running, without causing pollution of the air or contravening the current workshop regulations. Height and elevation is fully adjustable. Mounded on robust metal stand with adjustable suction settings. Working pressure: 5 to 8 bar Dimensions: 250mm x 280mm x 1230mm Weight: 9.14kg

No.7699 E / Zee Pull Exhaust Pipe Separator Simple and easy way to separate fused and previously clamped exhaust pipes and mufflers. The separating bolts have 1/2"Drive socket ends that will separate the two holding clamps easing the pipes apart from each other. Size: 2" to 2.1/4"(50mm to 58mm) TM

Optional Accessories:

No.213036 Dual Exhaust Hose Connector No.229001 3 Metre Extended Hose


155

T

&E OOLS

ENGINE - EXHAUST SERVICE TOOLS Exhaust Back Pressure Testers 7389 Back Pressure Test Adaptor Kit

7389

New test kit aids in diagnosing clogged or restricted exhaust systems. Allows comparing back pressure readings ahead and behind of suspected restriction. Kit includes small hole punch for use with an air hammer, five x 5/16" x 1/2" self tapping bolts and a test adaptor. Use self tapping bolts to plug hole after test is completed. Pressure gauge not included. Length: 7.1/2"(190mm) Note: Do not install directly into catalytic converter or muffler.

4390

4390

Exhaust Back Pressure Gauge for #7389 Kit

15psi Pressure Gauge for use with #7389 Back Pressure Test Adaptor Set. Indludes hose and connector fitting.

72408

Exhaust Back Pressure Accessory Kit

l

Washers, Inserts & Sealing Screws

Pack of 25 each, washers, inserts, sealing screws. Replacement pack for #7389 Exhaust Back Pressure Adaptor Kit.

4438

Exhaust Back Pressure Tester Sensor Type Adaptor fits into oxygen sensor hole enabling back pressure of mufflers and catalytic converters to be read on 0 to 15psi easy to read gauge. Suits most Australian, Asian, European and US Vehicles. Range: 0 to 15psi (0 to 1bar) Gauge Diameter: 2.1/2"(65mm) Supplied in blow mold case.

72408 4438

4439

3 Way Exhaust Back Pressure Kit This three way tester allows quicker accurate testing of exhaust blockages in catalytic converters, mufflers etc. 1. "Oxygen Sensor" adaptor includes 12mm & 13mm threads. Flange & gasket also included for cars with flange type sensors. 2. To test through the "exhaust pipe" threaded inserts, an installing tool, sealing screws and washers are included. Testing can be done on either side of the catalytic converter and muffler to pinpoint the blockage. 3. For testing through the "Air Induction System", four rubber adaptors & quick coupler plugs are included to use at the air induction inlet pipe fitting. Range: 0 to 15psi (0 - 1bar) Gauge Diameter: 2.1/2"(65mm) Supplied in blow mold case.

Exhaust Pipe Removers 4947 Exhaust Pipe Remover

4439

Insert between tailpipe and muffler joint, and split open which ever is outside. Rusted and corroded connections are no problem. The handle keeps your hands away from the hammer. Drop forged alloy steel. Length: 8"(200mm)

4947

7712 7712

7717

7717

156

TM

Exhaust Doughnut Remover / Replacer Removes and replaces rubber ring style hangers used on late model cars. Simply hook tool through rubber mounting ring and stretch until released from hook on muffler pipe or frame. Reverse procedure for installation. Length: 12"(300mm)

Exhaust Manifold Spreader

l For re-installing the manifold on small block engines

A simple way to expand a warped manifold so all bolt holes are accurately aligned. Helps prevent cross-threading of manifold bolts. Works best when used in pairs. Install before removing manifold to prevent mis-alignment. Range: 2.1/2" to 4"(65 to 100mm) Body Diameter: 3/4"(19mm) Length: 3.1/4"(82mm)


T

&E OOLS

ENGINE - EXHAUST SERVICE TOOLS Exhaust Pipe Reshapers

a

Heavy-duty alloy steel construction allows for strength and durability. Removes clamp grooves, rounded out pipes, and reshapes damaged exhaust tubing. Features extra long extended drive bar for easy expansion. a

J2001 a

J2002

a

J2003

a

J2001

Small Exhaust Pipe Reshaper

J2002

Capacity: 1.1/8" to 1.11/16"(28mm to 43mm) Length: 5"(125mm)

Medium Exhaust Pipe Reshaper

Capacity: 1.1/2" to 2.7/16"(38mm to 60mm) Length: 6.3/4"(171mm)

Large Exhaust Pipe Reshaper

Capacity: 2.1/8" to 3.7/16"(54mm to 88mm) Length: 8.3/4"(222mm)

J2003

Exhaust Pipe Reshapers Impact Type

Reshapes damaged exhaust pipe ends in seconds, remove clamp grooves, round out crushed or bent pipes to assure a tight fit eliminating exhaust leaks. Lightweight feature makes this frustrating job easy on or off the car. No holding fixture necessary. Impact resistant Delren® head for dead-blow driving with hammer. Supplied in plastic pouch with instructions. A

7703

Small Pipe Reshaper Impact Type

7703

Fits Pipe Sizes: 1.3/8" to 1.15/16"(35 to 50mm) Length: 6"(150mm)

a

7704

Medium Pipe Reshaper Impact Type

Fits Pipe Sizes: 1.13/16" to 2.1/2"(45 to 65mm) Length: 6.1/2"(165mm)

a

7705

7704

Large Pipe Reshaper Impact Type

Fits Pipe Sizes: 2.7/16" to 3.3/16"(60 to 80mm) Length: 6.3/4"(171mm)

7705

Exhaust Pipe Cutters 7707 Exhaust Pipe Cutting Pliers

7707

New design features increased diameter cutting wheels to suit new thick wall exhaust pipes. Cutting wheel on each roller for quicker cutting. Effective in hard to reach areas. Includes storage pouch. Capacity: 3/4" to 3.1/4"(19 to 83mm) Length: 10"(250mm)

a

7708

Replacement Cutter Chain for #7707

7700

Exhaust Pipe Cutter

Superior design to easily cut exhaust pipes without using gripping pressure. Simply hook chain to desired diameter, tighten chain by turning the knurled handle and swivel tool to cut. Tool has wide guide rollers between each cutter to ensure proper tracking. Supplied in sturdy vinyl storage pouch. Capacity: 3/4" to 3"(19 to 75mm) Length: 10"(250mm)

a

7701

7700


7722

Large Exhaust Pipe Cutting Pliers

New design features increased diameter cutting wheels to suit new thick wall exhaust pipes. Cutting wheel on each roller for quicker cutting. Effective in hard to reach areas. Extra large 6"(150mm) chain for cutting large exhaust pipes, large oil filters, etc. Includes storage pouch. Capacity: 3/4" to 6"(19 to 150mm) Length: 13.1/2"(340mm)

7722-C TM

Extra Large Capacity Cuts up to 6"Diameter Pipes 7722



157

T

&E OOLS

ENGINE - OIL FILTER WRENCHES Heavy-Duty

Standard-Duty

No.4297 Strap Type Oil Filter Wrench The rugged nylon strap can handle any filter up to 6"(150mm) diameter. The more leverage applied the tighter it grips. Handle can be turned with 1/2" drive bar or 3/4"(19mm) open end wrench. Capacity: 0 to 6"(0 to 150mm) Length: 6"(150mm)

No.4299 Strap Type Oil Filter Wrench Heavy-duty "Cordura" strap for high torque requirements. Features double ended forged body with 3/8"drive & 1/2"drive ends. Handles extra large size filters. Capacity: 0 to 12"(0 to 300mm) Length: 4"(100mm)

No.4278 Standard Spider Filter Wrench l l

Works Both Left & Right Hand Fits the Small Asian Filters thru to Large US Filters

Reversible style enables removal or installation of filters in hard to reach places. Features huge size range. For use when access to filter is only from the end. Three positive legs adjust to grip filter firmly. Drive Size: 3/8"Sq(1/2"Dr adaptor included) Capacity: 2.1/8" to 4.1/4"(55mm to 110mm)

No.4273 Filter Wrench Small Cup Type

No.4279 Spider Filter Wrench Works both left & right hand Reversible style enables removal or installation of filters in hard to reach places. Features huge size range. For use when access to filter is only from the end. Three positive legs adjust to grip filter firmly. Drive Size: 3/8"Sq. (1/2"Dr. adaptor included) Capacity: 2.1/2" to 4.3/4"(65 to 120mm) l

No.4274 Filter Wrench Medium Cup Type

Fits new Toyota filters plus most extra small filters. For use when access to filter is only from the end. Cam action design for easy adjustment and a firm positive grip of the filter. Drive Size: 3/8"Square Capacity: 2.3/8" to 3.1/8"(60 to 80mm)

Fits new Toyota filters plus most extra medium filters. For use when access to filter is only from the end. Cam action design for easy adjustment and a firm positive grip of the filter. Drive Size: 3/8"Square Capacity: 3.1/8" to 3.7/8"(80 to 98mm)

No.4276 Small Spider Filter Wrench

No.4277 Large Spider Filter Wrench

Features huge size range. For use when access to filter is only from the end. Three long knurl faced legs adjust to grip filter firmly. Drive Size: 3/8"Square (1/2"Dr Adaptor included) Capacity: 1.5/8" to 4.3/4" (41 to 120mm)

Features huge size range. For use when access to filter is only from the end. Three long knurl faced legs adjust to grip filter firmly. Drive Size: 3/8"Square (1/2"Dr Adaptor included) Capacity: 2.3/8" to 5.3/8" (60 to 135mm)

No.J4300 Chain Type Strap Wrench Features huge size range. Heavy-duty chain enables ratcheting action making it possible to re-grip without removal from filter. Also will handle all shapes, round, square, hexagon, octagon etc. Capacity: 5/8" to 5"(16 to 125mm) Length: 3.3/4"(95mm)

158

TM

No.A2094 Two Way Oil Filter Wrench Heavy duty forged steel two way oil filter wrench with serrated jaws to grip the filter securely. Spring loaded cam action reverses the drive direction for either removal or replacement. For use when access to filter is only from the end. Drive Size: 3/8"Square Capacity: 2.3/8" to 3.1/8"(60 to 80mm)


T

&E OOLS

ENGINE - OIL FILTER WRENCHES

No.4252 Extra Small Swivel Filter Wrench

No.4251 Small Swivel Filter Wrench

Dimples on band give a positive grip Unique band design will not crush filters Capacity: 2.3/8" to 2.7/8"(60mm to 73mm)


l

l

l

l

No.4255 Large Swivel Filter Wrench

No.4253 Standard Swivel Filter Wrench



l

l

l

l

Three Position Adjustment

Adjustable Filter Wrenches l l

Adjustable Oil Filter Pliers

Dimples on band give a positive grip Unique band design will not crush filters

Swivel oil filter wrench with notched links on the band. Simply set to one of the three notches to cover most sizes. These oil filter wrenches offer a wide universal range.

Heavy-duty forged pliers provide a secure hold on the most stubborn, tight filters. Features short handles for easy access in confined areas. Three position slip joint makes adjustment with greater range. Chrome alloy steel with plastisol coated handles.

No.4257 Adjustable Swivel Filter Wrench

No.4283

12" Adjustable Oil Filter Pliers

No.4260 Adjustable Swivel Filter Wrench

No.4283-10

10" Adjustable Oil Filter Pliers

Capacity: 2.3/4" to 4.1/4"(70 to 110mm)

Capacity: 3.7/8" to 4.3/4"(98 to 120mm)

Capacity: 3.11/32" to 4.5/8"(85mm to 115mm)

Capacity: 2.11/32" to 3.9/16"(60mm to 90mm)

Length: 12"(300mm)

Length: 10"(250mm)

Five Position Groove Joint

No.4284 Adjustable Oil Filter Pliers

Heavy-duty forged pliers feature five position tounge and groove box joint adjustment. Makes for fast and easy adjustment with greater range. Chrome alloy steel with plastisol coated handles. Capacity: 2.1/8" to 5"(55mm to 125mm) Length: 11.3/8"(290mm)

No.4305 18" Adjustable Oil Filter Pliers

Heavy-duty forged pliers provide a secure hold on the most stubborn tight filters. Features long handles for easy access in confined areas. Three position slip joint makes adjustment fast and easy with greater range. Chrome alloy steel with plastisol coated handles. Capacity: 3.1/4" to 7"(95mm to 180mm) Length: 18"(450mm)

Chain Oil Filter Wrenches Adjustable offset handles with double width chains for more surface grip on the filter. Vanadium steel with high tensile chains.

No.4271 Standard Chain Oil Filter Wrench Capacity: 2.3/8" to 4.1/8"(60mm to 105mm) Length: 13.3/4"(350mm)

No.4272 Large Chain Oil Filter Wrench Capacity: 2.3/8" to 6.3/8"(60mm to 160mm) Length: 20.1/2"(520mm)

3/8"Drive Band Type Oil Filter Wrenches For inaccessible areas disassemble band at pivot bolt, wrap around filter reassemble and remove filter.

No.4262 3/8"Drive Small Oil Filter Wrench Capacity: 2.3/4" to 3.1/8"(70 to 80mm)

No.4264 3/8"Drive Medium Oil Filter Wrench Capacity: 3.1/16" to 3.7/16"(75 to 85mm)

No.4266 3/8"Drive Large Oil Filter Wrench Capacity: 3.7/16" to 3.3/4"(85 to 95mm) TM


159

T

&E OOLS


Suits "Ryco" Octagonal End Cap Filters

No.4286 Strap Type Truck Filter Wrench

The heavy duty webbing strap can handle any filter up to 12"(300mm) diameter. No.HC9000 The support pad helps to grip the "Ryco" 8 Flute Filter Wrench Set Set Contains: filter without crushing it. The more leverage applied the tighter it grips. No.HC8077 77mm x 8 Flute Cup Type Filter Wrench Suits Ryco: Z63, Z68 & Z131A etc. Use with any 1/2" drive bar. Capacity: 12"(300mm) No.HC8078 93mm x 8 Flute Cup Type Filter Wrench Strap Length: 40"(1015mm) Suits Ryco: Z89A & Z170 etc.

No.HC8079 85mm x 8 Flute Cup Type Filter Wrench

4286-STR Strap & Pin for #4286

Suits Ryco: Z130A, Z142A & Z256B etc.

No.4301B Heavy Duty Oil Filter Wrench

No.4285 Locking Grip Oil Filter Pliers

Heavy duty oil filter wrench features huge size range. For use when access to filter is only from the end. Three long knurl faced legs adjust to grip filter firmly. 1/2" Square Drive Capacity: 3.3/4" to 6.1/2"( 95 to 165mm )

These multi-purpose locking pliers will lock and grip oil filters or any irregular shaped object for quick positive tightening or removal. They can be adjusted and fastened for applications at any angle. Capacity: 2.1/8" to 4.1/2"(55 to 120mm) Length: 10"(250mm)

No.4298 5Pc. Oil Filter Wrench Set Made from alloy steel, wrench can with-stand up to 85ft/lb. of torque. The fluted cup style grips firmly on the flutes eliminating crushing of the filter. Five cup style 3/8" Drive wrenches to suit Mazda, Nissan, Toyota etc. a

Set Contains:

Part No. HC7630 HC75614A HC9315


Diameter 76mm 75.6mm 93mm

Flutes 30 14 15

Description Part No. Mazda, Nissan, Toyota etc. HC6514 Mazda, Nissan, Toyota etc. HC7614 Mazda, Nissan, Toyota etc.

Diameter Flutes Description 14 65mm Mazda, Nissan, Toyota etc. 14 76mm Mazda, Nissan, Toyota etc.

1/2"Drive Truck Oil Filter Wrenches These heavy-duty truck oil filter wrenches are designed for the high torque requirements of truck filters. The 1.1/2"(38mm) wide, & 3"(75mm) extra deep tough steel band with unique clamping design will remove the toughest filters without crushing. All sizes 1/2"Square Drive. New Design Features Heavy-Duty Rivets

1.1/2"(38mm) Wide Bands

4280 H/Duty Oil Filter Wrench Capacity: 4.1/8" to 4.3/4" (105 to 120mm)

4281 H/Duty Oil Filter Wrench

4280

4281

4282

Capacity: 4.1/2" to 5.1/4" (115 to 135mm)

4282 H/Duty Oil Filter Wrench Capacity: 5" to 5.3/4"

(125 to 145mm)

3"(76mm) Wide Bands

4280W H/Duty Oil Filter Wrench Capacity: 4.1/8" to 4.3/4" (105 to 120mm)

4281W H/Duty Oil Filter Wrench

4280W

4281W

4282W

Capacity: 4.1/2" to 5.1/4" (115 to 135mm)

4282W H/Duty Oil Filter Wrench Capacity: 5" to 5.3/4"

160

TM

(125 to 145mm)


ENGINE - OIL FILTER WRENCHES No.4292 9Pc. Euro Cup Style Oil Filter Wrench Set

T

&E OOLS

Made from alloy steel, wrench can with-stand up to 85ft/lbs of torque. The fluted cup style grips firmly on the flutes eliminating crushing of the filter. Nine wrenches to suit European vehicles, plus 21mm offset wrench. Set Contains:


Part No. Diameter Flutes HC2706A 6 Flutes 27mm HC3206A 6 Flutes 32mm HC3606A 6 Flutes 36mm HC7614A 76mm 14 Flutes HC75614A 75.6mm 14 Flutes HC8616A 86mm 16 Flutes HC7612A 76mm 12 Flutes HC9315A 93mm 15 Flutes HC4228K -

Drive 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" -

Vehicle Mercedes Mercedes, GM Mercedes, VW, Cooper S New Mercedes New Mercedes Volvo Honda, Opel, Ducato, Renault Volvo, VW, Audi, Nissan, Porsche 21mm Offset Wrench Handle

Includes: 21mm Offset Oil Filter Wrench

No.4307 9Pc. Truck Oil Filter Wrench Set

Made from alloy steel, wrench can with-stand up to 85ft/lbs of torque. The fluted cup style grips firmly on the flutes eliminating crushing of the filter. Seven cup type wrenches to suit truck applications, adjustable strap type wrench, plus 21mm offset wrench. Set Contains:


Part No. Diameter HC3606B 36mm HC7614B 76mm HC10615B 106mm HC10715B 107mm HC10815B 108mm HC10818B 108mm HC13518B 135mm HC4226K 0-160mm HC4228K -

Flutes 6 Flutes 14 Flutes 15 Flutes 15 Flutes 15 Flutes 18 Flutes 18 Flutes -

Drive 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" -

Vehicle Mercedes, Scania Mercedes, VW Man, Scania, Iveco Volvo, Iveco, Renault, Scania Volvo, Iveco, Renault, Scania Renault Transporter Man Trucks Universal Strap Wrench 21mm Offset Wrench Handle

Includes: Universal Oil Filter Strap Wrench 21mm Offset Oil Filter Wrench

No.4303 7Pc. Oil Filter Wrench Set

Pressed from Chrome Vanadium steel, wrench can with-stand up to 85ft/lbs of torque The 6 point shallow shape enables the sockets to fit into confined areas. Six pressed sockets to suit later European applications. Includes 1/2" x 3/8" reducing adaptor. Set Contains:

Part No. HC2406 HC2706A HC3006 HC3206A HC3606A HC3806


Diameter 24mm 27mm 30mm 32mm 36mm 38mm

Opening 6 Point 6 Point 6 Point 6 Point 6 Point 6 Point

Drive 3/8" 3/8" 3/8" 3/8" 3/8" 3/8"

Vehicle GM Cadillac, BMW Mercedes, A Class 5.9 L. Cummins fuel filter Vauxhall / Opel Vectra Ford Diesel, Mercedes Vauxhall / Opel Vectra

Includes: No.24803 1/2" Female x 3/8" Male Reducing Adaptor

No.4298B 5Pc. Oil Filter Wrench Set Forged from Chrome vanadium steel, wrench can with-stand up to 85ft/lbs of torque The 6 point shallow shape enables the sockets to fit into confined areas. Five forged sockets to suit later European applications. Set Contains:

Part No. 4221 4223 4225 4226 4227 TM


Diameter 24mm 27mm 32mm 36mm 38mm

Opening 6 Point 6 Point 6 Point 6 Point 6 Point

Drive 3/8" 3/8" 3/8" 3/8" 3/8"

Vehicle GM Cadillac, BMW Mercedes, A Class Vauxhall / Opel Vectra Ford Diesel, Mercedes Vauxhall / Opel Vectra


161

T

&E OOLS


No.5200 Mitsubishi Canter Oil Filter Wrench

101mm Diameter with 15 Flutes Oil Filter Wrench designed for removal and replacement of oil filters fitted on Mitsubishi Canter engines. Made from heat treated steel with fully welded construction. Drive Size: 1/2"Square Opening: 101mm x 15 Flutes

No.4294 16Pc. Cup Style Oil Filter Wrench Set Fourteen wrenches to fit the following eighteen sizes, plus 1/2" x 3/8" Adaptor. Set Contains:

Part No. HC6606 HC7608 HC7612 HC7476 Stepped

HC7614 HC8616 HC8618 HC9210


Diameter 66mm 76mm 76mm 74mm 76mm 76mm 86mm 86mm 92mm

Flutes 6 8 12 15 15 14 16 18 10

Part No. Diameter Flutes HC9315 93mm 15 HC9345 93mm 45 HC9618 96mm 18 HC10615 106mm 15 HC10815 108mm 15 HC10818 108mm 18 4278 3 Leg Spider Filter Wrench 24803 1/2" x 3/8" Adaptor

No.4295 15Pc. Cup Style Oil Filter Wrench Set

Fourteen wrenches to fit the following eighteen sizes, plus 1/2" x 3/8" Adaptor. Set Contains:

Part No. HC6514 HC6814 HC7314 HC7476 Stepped

HC7614 HC8015 HC9315 HC9336



Flutes 14 14 14 15 15 14 15 15 36

Part No. HC6567 Stepped

HC8082 Stepped

HC9015 HC7577 Stepped

HC7630 HC10015


Flutes 14 14 15 15 15 15 15 30 15

No.4296 30Pc. Cup Style Oil Filter Wrench Set Set contains 28 cup style oil filter wrenches, spider adjustable filter wrench plus 1/2"Drive x 3/8"Drive Male Adaptor. Set Contains:

Part No. HC7815 HC6567 HC6514 HC6814 HC7415 HC6606 HC7608 HC7314 HC7476 HC7577 HC7612 HC7630 HC9336 HC7614

162


Flutes Diameter 15 78mm 65mm, 67mm 14 14 65mm 14 68mm 15 74mm 6 66mm 8 76mm 14 73mm 74mm, 76mm 15 75mm, 77mm 15 12 76mm 30 76mm 36 93mm 14 76mm TM

Part No. HC10815 HC10818 HC10615 HC10015 HC8616 HC9015 HC8082 HC9210 HC9345 HC9315 HC8618 HC8015 HC9615 HC9515

Diameter Flutes 108mm 15 108mm 18 106mm 15 100mm 15 86mm 16 90mm 15 80mm, 82mm 15 92mm 10 93mm 45 93mm 15 86mm 18 80mm 15 96mm 15 95mm 15


T

&E OOLS

ENGINE - OIL FILTER CRUSHER & WRENCHES Cup Style Oil Filter Wrenches Individual Sizes Made from alloy steel, withstand up to 85ft/lbs of torque. The fluted cup style grips firmly on the flutes eliminating crushing of the filter. Individual Sizes:

Part No. HC2406 HC2706A HC3006 HC3206A HC3606A HC3606B HC3806 HC6414 HC6514 HC6567 HC65714 HC6606 HC66514 HC6814 HC7314 HC7415 HC7476 HC7577 HC75614A HC7612 HC7612A HC7608 HC7614 HC7614B HC7630 HC76514 HC7815 HC8015 HC8082 HC8414 HC8618 HC8616 HC8616A HC88515 HC9015 HC9210 HC9345 HC9315 HC9315A HC9336 HC9515 HC9618 HC9915 HC10015 HC10615B HC10715B HC10815B HC10818B HC13518B


Diameter 24mm 27mm 30mm 32mm 36mm 36mm 38mm 64mm 65mm 65 & 67mm 65.7mm 66mm 66.5mm 68mm 73mm 74mm 74 & 76mm 75 & 77mm 75.6mm 76mm 76mm 76mm 76mm 76mm 76mm 76.5mm 78mm 80mm 80 & 82mm 84mm 86mm 86mm 86mm 88.5mm 90mm 92mm 93mm 93mm 93mm 93mm 95mm 96mm 99mm 100mm 106mm 107mm 108mm 108mm 135mm

Flutes 6 Flutes 6 Flutes 6 Flutes 6 Flutes 6 Flutes 6 Flutes 6 Flutes 14 Flutes 14 Flutes 14 Flutes 14 Flutes 6 Flutes 14 Flutes 14 Flutes 14 Flutes 15 Flutes 15 Flutes 15 Flutes 14 Flutes 12 Flutes 12 Flutes 8 Flutes 14 Flutes 14 Flutes 30 Flutes 14 Flutes 15 Flutes 15 Flutes 15 Flutes 14 Flutes 18 Flutes 16 Flutes 16 Flutes 15 Flutes 15 Flutes 10 Flutes 45 Flutes 15 Flutes 15 Flutes 36 Flutes 15 Flutes 18 Flutes 15 Flutes 15 Flutes 15 Flutes 15 Flutes 15 Flutes 18 Flutes 18 Flutes

Description 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Dual Size Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Dual Size Oil Filter Wrench 3/8"Drive Dual Size Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Dual Size Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench, Hex Adaptor 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 3/8"Drive Cup Style Oil Filter Wrench 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor 1/2"Drive Cup Style Oil Filter Wrench 1/2"Drive Cup Style Oil Filter Wrench, Hex Adaptor

No.WH312A Car & Truck Oil Filter Crusher

Cup Style Fluted Oil Filter Wrenches Adaptor Type Cup Style Fluted Oil Filter Wrench

AFTER

BEFORE

Air Pressure Valve

Air Safty Switch

TO&E OLS

The Professional Advantage q q q

Heavy-Duty Oil Filter Crusher

WH312A

This heavy- duty pneumatically operated heavy vehicle oil filter crusher will handle filters up to 11"(280mm) in height and 5.1/2"(140mm) diameter. The filters are reduced to only 20% of their original size and after pre-draining, 95% of the residual oil is removed. Automatic cycle operation: Simply load the filter, push the button and walk away. A shield protects the operator and a security switch prevents operation if shield is in the open position. Unique safety door ensures that the filter crusher will not operate unless the door is completely closed. Use waste oil drum under stand. Power: Compressed Air 100 to 120psi Dimensions: 320mm x 330mm x 770mm TM


163

T

&E OOLS

RADIATOR PRESSURE TESTER SETS

Radiator Pressure Tester Sets Sets provide both manual and automatic pressurization of the entire cooling system. The Automatic Air Inlet Pump includes shut-off valve, preset regulator valve, pressure relief valve, colour coded pressure gauge and quick release fittings. The hand pump is constructed from high impact, stronger than steel Polymer to prevent against glycol corrosion. Adaptors suit most passenger and light commercial vehicles and are colour coded for easy identification. Three special adjustable depth seat adaptors cover most conventional radiator tank necks.

Includes Both Hand Pump & Automatic Air Inlet Pump

Constructed from High Impact, Stronger than Steel Polymer to Prevent Against Glycol Corrosion

Includes all Adaptors with Mark *

Includes all Adaptors with Mark *

No.RT-919A Radiator Tank Pressure Test Set

No.RT-919C Deluxe Radiator Tank Pressure Test Set D

C

D D

B

C

A

B

A A

No.RT-919J Radiator Cap Pressure Tester

B

No.RT-919F Truck Radiator Pressure Test Set The kit comes with four tapered adaptors that can quickly expand to make the correct seal on truck radiator necks. The range provides coverage for most Japanese, American & European trucks, tractors, farm equipment etc. Quick release couplers make pump hook up an easy operation. Hand pump is constructed from high impact, stronger than steel polymer to prevent against glycol corrosion. Gauge Pressure: 35psi Gauge Dia.: 1.7/8"(48mm) Set Contains: A B C D

No.RT919-81 No.RT919-82 No.RT919-83 No.RT919-84

Expanding Taper Adaptor Expanding Taper Adaptor Expanding Taper Adaptor Expanding Taper Adaptor

Available Separately Range: 16mm to 35mm Range: 25mm to 40mm Range: 35mm to 50mm Range: 45mm to 60mm

Accessories & Replacement Parts

No.RT919-T1 Automatic Air Inlet Pump 164

TM

No.RT919-P1 Hand Pump

B C D E F G H I

C

F

G

H

I

A

Set Contains: A

E


No.RT919-51 Radiator Cap Adaptor Toyota, Lexus & many late mode Asian vehicles. Cap Size: 31mm Dia. x 10mm Reach No.RT919-52 Radiator Cap Adaptor Toyota, Subaru, Nissan, Mitsubishi & Honda vehicles. Cap Size: 32mm Dia. x 16mm Reach No.RT919-53 Radiator Cap Adaptor Standard bayonet style caps. Cap Size: 1.5/8" Dia. x 3/4" Reach No.RT919-54 Radiator Cap Adaptor Audi, Porche, Renault & VW. Cap Thread Size: 45 x 3mm Internal No.RT919-55 Radiator Cap Adaptor Citroen, Fiat, Peugeot, Renault & Volvo. Cap Thread Size: 48 x 3mm Internal No.RT919-56 Radiator Cap Adaptor Opel, Holden, Camira, VW, Ford. Cap Thread Size: 52 x 3mm Internal No.RT919-57 Radiator Cap Adaptor Volvo & Renault. Cap Thread Size: 44 x 3mm Internal No.RT919-58 Radiator Cap Adaptor BMW 1998 to current. Cap Thread Size: 53 x 4mm Internal No.RT919-59 Radiator Cap Adaptor Mercedes Benz etc. Cap Thread Size: 62 x 4mm Internal

No.RT-919G Replacement Gauge 1.7/8"(48mm) Diameter 35psi Pressure Gauge

No.RT1001 Replacement Female Coupler

With automatic drain filter.


RADIATOR PRESSURE TESTER ADAPTORS

* *

* *

* *

No.RT919-02 No.RT919-03 No.RT919-04 Radiator Tank Adaptor Radiator Tank Adaptor Radiator Tank Adaptor

T

&E OOLS * *

No.RT919-05 Radiator Tank Adaptor

Suits: Audi A4, A5, A6. Suits: Opel, Holden, Camira, Suits: BMW. Tank Thread 52 x 3mm Internal VW, Ford. Tank Thread 52 x 3mm Internal Suits: BMW Size: 58 x 3mm External Tank Thread Size: 52 x 3mm Ext. Size: 63 x 3mm External Tank Thread Size: 52 x 4mm Ext.

* *

No.RT919-06 Radiator Tank Adaptor Suits: Volvo, Citroen, Renault,

* *

No.RT919-07 Radiator Tank Adaptor

Peugeot.

Suits: Audi, Porche, VW. Tank Thread Size: 48 x 3mm Ext. Tank Thread Size: 45 x 3mm Ext.

* *

Use with #RT919-08 Adjustable Bridge for all necks from 27mm diameter and up.

* *

No.RT919-08 No.RT919-09 Bridge for Adjustable 50mm Adjustable Seat Seats Adjustable bridge clamp for use with 27mm, 35mm, 50mm adjustable seats.

Use with #RT919-08 Adjustable Bridge for all necks from 50mm diameter and up.

* *

* *

* *

No.RT919-10 No.RT919-11 35mm Adjustable Seat 27mm Adjustable Seat Use with #RT919-08 Adjustable Bridge for all necks from 35mm diameter and up.

* *

No.RT919-12 31mm Tank Adaptor Suits: Toyota, Lexus and many

late model Asian vehicles. Tank Size: 31mm dia. x 10mm

No.RT919-13 32mm Tank Adaptor Suits: Toyota, Subaru, Nissan,

Mitsubishi and Honda.

reach filler necks. Use with #RT919-08 Bridge

Tank Size: 32mm filler necks.

Top seal only.

* No.RT919-44 Small Radiator Neck Bracket

For use with #RT919-08 bridge on small radiator necks. Helps to support the clips around the top of the radiator neck.

*

No.RT919-19 No.RT919-20 No.RT919-40 Radiator Tank Adaptor Radiator Tank Adaptor Radiator Tank Adaptor (Black) Mercedes Benz (Green) Ford

Suits: Ford Falcon EA model with

Suits: ML30 Mercedes. Thread Size: 54 x 3mm

* *

Suits: Ford. Thread Size: 51 x 3mm

* *

No.RT919-41 No.RT919-43 Radiator Tank Adaptor Radiator Tank Adaptor Suits: Toyota, Lexus, Honda and

Suits: Toyota, Subaru, Nissan,

many late model Asian vehicles. Tank Size: 31mm dia. x 10mm reach filler necks.

Tank Size: 32mm dia. x 16mm

TM

Mitsubishi and Honda. reach filler necks.

threaded radiator cap. Tank Thread Size: 55 x 3mm Ext.

*

No.RT919-45 Radiator Tank Adaptor Suits: Standard bayonet style

filler necks. Tank Size: 1.5/8"dia.

*

No.RT919-60 Radiator Tank Adaptor Suits: Mercedes Benz etc. Tank Thread Size: 62 x 4mm Ext.


165

T

&E OOLS

RADIATOR PRESSURE TESTER SETS

Includes 12 Adaptors No.G02 to No.G13 Shown on Page No.167 Except No.G06-F No.GO6-F BA Falcon Adaptor is Available as an Optional Extra

No.GT3 Radiator Pressure Tester No.GT1 Deluxe Radiator Pressure Tester Set

This radiator pressure tester is the quick, accurate way to tell instantly if a cooling system or radiator cap is defective. There's no guesswork. You can see exactly where repair or replacement is needed. Features an all metal body construction with a 24"(600mm) flexible hose and built-in manual pressure release valve. The easy to read colour coded 3"(75mm) diameter gauge is calibrated to specific system pressure scales. Capacity: 35psi (2.5bar) in 1psi increments. Set includes: 12 adaptors #G02 to #G13, plus #4101 Thermometer.

This radiator pressure tester is the quick, accurate way to tell instantly if a cooling system or radiator cap is defective. You can see exactly where repair or replacement is needed. Fast efficient system testing without the need of many different adaptors. The expandable rubber adaptor allows the tester to attach to most passenger & light commercial vehicles via the bayonet & threaded filter necks on radiator & header tanks. Features an all metal body construction with a 24"(600mm) flexible hose and built-in manual pressure release valve. The easy to read colour coded 3"(75mm) diameter gauge is calibrated to specific system pressure scales. Set Contains: Standard bayonet tank adaptor, 31x16mm & 32x10mm Asian adaptors, Radiator Expanding adaptor and 3 rubber spacers, hand pump and thermometer.

Includes All (Nylon) Adaptors Shown on Page No.167 Plus G03 G04 & G05

Expands From 1.1/16" to 2"(27 to 50mm)

Also Includes 4103 Thermometer & GTW Adaptor Wrench

No.GT4 Radiator Expanding Adaptor No.GT5 Universal Radiator Pressure Tester Set

This new set is made from composite nylon material and offers the most comprehensive range of adaptors at an economical price.

No.GT7 Universal 5/16",3/8" In line Radiator Adaptor Set This in line adaptor enables you to connect your radiator tester directly in line to the tank reservoir. Use when the correct adaptor is not available.

166

TM

Fast efficient system for testing without the need of many different adaptors. The expanding rubber adaptor together with the three extra bushes allows the tester to attach to reservoir and tanks on most passenger & light commercial vehicles. Capacity: 1.1/16" to 2"(27 to 50mm) Length: 5"(125mm) a

No.GT4BUSH

Four Replacment Rubber Bushes for GT4 Expanding Adapter

No.G01 Hand Pump (Alloy) No.G01N Hand Pump (Nylon)

Length: Hand Pump: 9.1/4"(235mm) Diameter: Gauge: 3"(76mm)

No.GTH No.GTG

Hose: 24"(610mm)

Replacement Hose for G01 Hand Pump Replacement Gauge for G01 Hand Pump


RADIATOR PRESSURE TESTER ADAPTORS

No.G02 Truck Bayonet Tank Adaptor Fits all popular trucks with large 2.11/16" diameter "B" size filler neck.

No.G03 Standard Bayonet Tank Adaptor For use to check 3/4"deep standard bayonet filler neck.

No.G04 Small Diameter Tank Adaptor

No.G05 Extra Small Diameter Tank Adaptor

Suits: Toyota, Lexus, and many Nissan, Peugeot, Subaru, Suzuki, late model Asian vehicles. Size: 31mm dia. x 10mm reach Toyota. Size: 32mm dia.x16mm Suits: Honda, Mazda, Mitsubishi,

No.G07 (Alloy) No.G06 (Alloy) No.G06-F (Alloy) No.G07N (Nylon) No.G06N (Nylon) Threaded Tank Adaptor Ford BA Tank Adaptor Threaded Tank Adaptor Suits: Commodore, Camira, Opel, Suits: Ford BA to current models: Suits: Alfa Romeo, Audi, Citroen,

Jaguar, Range Rover, Saab etc. Size: 52 x 3mm Female Thread

T

&E OOLS

No.G08 (Alloy) No.G08N (Nylon) Threaded Tank Adaptor

Falcon, Fairmont, Fairlane, LTD. Fiat, Jeep,Peugeot, Renault, Saab Suits: Volkswagen 1992 to current Volvo etc. Size: 45 x 3mm Thread Size: 57 x 3mm Male Thread Size: 52 x 2.5mm

No.G12 (Alloy) No.G09 (Alloy) No.G10 (Alloy) No.G11 (Alloy) No.G12N (Nylon) No.G09N (Nylon) No.G10N (Nylon) No.G11N (Nylon) Threaded Tank Adaptor Threaded Tank Adaptor Threaded Tank Adaptor Threaded Tank Adaptor Suits: Ford, International, GM & Suits: BMW, Volkswagen etc. Size: 63 x 3mm Male Thread

Suits: BMW 1998 to current. Size: 53 x 4mm Female Thread

Suits: Audi, Porsche, VW etc. Size: 48 x 3mm Female Thread

Rover. Size: 53 x 3mm Female Thread

No.G13 (Alloy) No.G02A (Nylon) No.G13N (Nylon) No.G14 (Nylon) No.G15 (Nylon) 32x16mm Cap Adaptor Threaded Tank Adaptor Threaded Tank Adaptor Threaded Tank Adaptor Suits: 32mm diameter x 16mm Suits: Mercedes Benz etc. Size: 62 x 4mm Female Thread

Suits: Ford Size: 53 x 3mm Female Thread

No.G02B (Nylon) 31x10mm Cap Adaptor

No.GTW Adaptor Wrench

Suits: 31mm diameter x 10mm

Fits all adaptors enables you to reach caps. Toyota, Lexus, and tighten and loosen adaptors many late model Asian vehicles. without over torqueing. TM

Suits: Mazda Size: 50 x 2.5mm Female Thread

reach caps. Toyota, Subaru, Nissan, Mitsubishi and Honda.

No.GTR Replacement Seals

No.4103 Large Radiator Temperature Gauge

Replacement seals and O rings to suit all adaptors.

Gauge Diameter : 2"(50mm) Range: 0 to 400°F (0 to 220°C)


167

T

&E OOLS

RADIATOR PRESSURE TESTER & ADAPTORS Stant Radiator Pressure Tester 12270 Stant Radiator Pressure Tester

The #12270 pressure tester is the quick, accurate way to tell instantly if a cooling system or radiator cap is defective. There's no guesswork. You can see exactly where repair or replacement is needed. Features an all metal body construction with a 14"(355mm) flexible hose and built-in manual pressure release valve. The easy to read colour coded 2"(50mm) diameter gauge is calibrated to specific system pressure scales. Supplied in its PVC carry case with one #12559 spacer to drop in 1"deep filler necks for testing, one #12552 Cap Adaptor to check 3/4"deep caps and a full instruction manual. Capacity: 30psi(200kpa) in 1psi increments.

a

Stant Radiator Pressure Tank & Cap Adaptors

12552

Set No.12270

a

12450

a

12453

12453

Set No.12450 a

12015

a

12016

a

12552

12017

12015

a

12018

a

12019

a

12016

12017

12018

12021

a

12023

Stant Replacement Cap Adaptor

For use to check 3/4"deep caps (both ends are 3/4"deep). Included in #12270 set.

Stant Truck Adaptor Kit

Includes both cap and radiator neck adaptors and one 7/8" rubber plug (#12451). Fits all popular trucks with large 2.11/16"diameter "B" size filler neck.

Stant Filler Neck Adaptor Kit

Includes #12452 rubber gasket and the truck "B" size filler neck adaptor. Part of #12450 kit.

Stant Truck Threaded Tank Adaptor

Suits: White, GMC etc.

Stant Threaded Tank Adaptor

Suits: Audi, Porsche & Volkswagen.

Stant Threaded Cap Adaptor

Suits: Audi, Porsche & Volkswagen.


Suits: Volvo, Saab & Renault.


Suits: BMW 1987 and earlier.

Size: 2.1/2" x 10tpi Size: 48 x 3mm Size: 48 x 3mm Size: 45 x 3mm Size: 52 x 3mm

Stant Small Diameter Cap Adaptor

Suits: Small 32mm dia. x 16mm reach

Size: 32 x 16mm caps. Toyota, Subaru, Nissan, Mitsubishi & Honda.


Suits: Commodore, Camira,

Size: 52 x 3mm

Jaguar, Range Rover, etc. a

12019

12021

12023

12024

a

12025

Stant Extra Small Cap Adaptor

Suits: 31mm dia. x 10mm reach caps.

Size: 31 x 10mm Toyota, Lexus & many late model Asian vehicles.

Stant Extra Small Tank Adaptor

Suits: 31mm dia. x 10mm reach filler necks. Size: 31 x 10mm

Toyota, Lexus and many late model Asian vehicles. a

12024

12025

12026

12026

a

12027


Suits: U.S. Ford & GM '93 - on.

Size: 52 x 2.5mm

Stant Small Diameter Tank Adaptor

Suits: Small 32mm dia. x 16mm reach filler Size: 32 x 16mm

necks. Toyota, Subaru, Nissan, Mitsubishi & Honda. a

12028

12028

12027

168

TM

12030

a

12030


Suits: Volkswagen 1992 to current.


Suits: BMW 1998 to current.

Size: 57 x 3mm Size: 53 x 4mm


T

&E OOLS

RADIATOR PRESSURE TESTER ADAPTORS Stant Accessories & Replacement Parts 12452

Stant Truck Rubber Gasket Suits: #12453 adaptor. Replacement for #12450 kit.

a

12559

12559

12452

Stant Replacement Rubber Spacer 1/4"Spacer for testing 1"deep filler necks.

a

12451

12451

Stant Truck Rubber Spacer Suits: #12450 Truck adaptor kit. (7/8"Thick)

a

12553

Stant Replacement Check Valve

a

12555

Stant Replacement Pump Seal

12556

Stant Replacement Plastic Knob

12702

Stant Replacement Pressure Gauge

a a

12703

No.12031 Adaptor Gasket Replacement Pack

Stant Head Attachment Repair Kit For #12270 Radiator Pressure Tester.

12701

12031

12553

12556

12702

Stant Radiator Conversion Kit Includes: Head, gauge and hose assembly

to convert #ST255 to #12270 (ST270)

12704

12555

12703

12704

12701

Stant Replacement Head & Hose Assembly For #12270 & #ST255 Radiator Pressure Tester.

12031

Stant Adaptor Gasket Replacement Pack Renew sealing integrity with this 12 piece gasket set.

Coolant Refiller Sets RT-919K

KO43

Radiator Coolant Refiller Set

Quick & easy way to refill coolant during radiator cooling system bleeding process. Supplied with 3 different types of radiator tank adaptors for quick connection. Length: 9.1/4"(235mm) Diameter: 6.3/8"(162mm)

KO41 KO50 RT-919K Set

a

Set Contains:

KO43 KO41 KO50


Filling Process

Mitsubishi, Nissan, Mazda Adaptor Honda, Lexus, Toyota Adaptor Standard bayonet fitting Adaptor

RT-919K1 Universal Coolant Filling Tool Set Quick & easy way to refill coolant during radiator cooling system bleeding process. Supplied with 5 universal radiator tank adaptors for quick connection.

RT-919HA Universal Coolant Filling Adaptor Set

RT-919K1 Set

Five piece replacement universal adaptor set as included with RT-919K1 Universal Coolant Filling Tool Set.

Prevents Air Locks & Overheating!

Coolant Evacuator Set 12275 Coolant Evacuator & System Tester After draining the radiator the tester will evacuate all the air from the system. Within two to three minutes the gauge will read that vacuum is held and there are no leaks. Coolant then can be refilled into the coolant system without creating any air locks. Supplied with interchangeable sleeves and tapered cones to fit all radiator necks. Length: 6.1/2"(165mm) Gauge Diameter: 1.1/2"(38mm)

12275GAUGE Replacement Gauge for #12275 Coolant Evacuator & Test System TM

Filling Process

Vacuum & Test

12275


Coolant Refilling

169

T

&E OOLS

RADIATOR SERVICE TOOLS & GAUGES

No.4101 Universal Automotive Thermometer Simply check radiator temperature with this 1"(25mm) diameter stainless steel constructed gauge. Also used on all automotive air conditioning systems. Comes with handy pocket storage case. Gauge Diameter: 1"(25mm) Range: 0 to 220°F(-18° to 110°C) Length: 5"(125mm)

No.4103 Large Radiator Temperature Gauge Simply check radiator temperature with this large diameter stainless steel constructed gauge. Also used on all automotive air conditioning systems. Comes with handy pocket storage case. Gauge Diameter: 1.3/4"(45mm) Range: 0 to 220°F(-18° to 110°C) Length: 5"(125mm)

Fits 1/2", 5/8", 3/4"(13mm, 16mm and 19mm) Heater Hoses Uses compressed Air & Standard Garden Hose Fitting

No.4356 Radiator Back Flusher

Pressurised air and water cleans cooling systems and heater cores without disassembly. No need to use caustic solutions. The radiator pressure cap remains in place to prevent over boosting. Saves costly replacement of the most stubbornly clogged heater cores. Corrosion resistant aluminium construction. Length: 5"(127mm)

No.7566 Radiator Hose Tool Speed up the removal and installation of radiator hoses. Just place the #7566 between the hose and connector to start hose into place. Made from hardened forged alloy steel. Length: 7.1/4"(185mm)

No.5727 Radiator Hose Clamp Socket Suits thumb screw aircraft type hose clamps. Features two different size slots in end. Fits over thumb screws on hose clamps for tightening or loosening. Made from alloy steel & chrome plated. Drive Size: 1/4"Square US Federal Stock No.: 5120-00-542-4751 Length: 1"(25mm)

No.4093 Digital Temperature Thermometer Large LCD display, measures a wide range of temperature. On / Off, auto power off, C° / F° conversion, stainless steel spindle with steel clip for holding the thermometer when measuring hot object. Range: -40 to 200°C (-40 to 392°F) Accuracy: +- 1°C

No.5724 Heater Hose Disconnect Tool Removes heater hoses with 5/8" and 3/4" quick disconnect couplings from rear heater core on 1987 to current Dodge Caravan and Chrysler Voyager vans. Also gets into difficult access areas next to firewall on 1986 to current Ford Aerostar vans. Length: 20"(500mm)

No.4105 Universal Radiator Petcock Socket Used to open and close petcocks used in radiators, engine blocks, liquid storage tanks, etc. Can be used with 1/4"drive ratchet or 7/8"wrench. O-ring holds socket or wrench in place, allows one hand operation for use in confined areas. Prevents damage to ears on petcock. Two slot design allows for use on all types of petcocks. Length: 1.1/4"(32mm) Slot Openings: 10mm & 5mm

Do Not Open Cap if Radiator is Hot as Hot Fluid Can Erupt & Cause Burns

No.4235 Radiator Service Tool Set No.4239 Radiator Cap Wrench Pliers

TM


No.4249 Heater Hose Slitter Length: 6"(150mm) No.4105 Radiator Petcock Socket Length: 1.1/4"(32mm) No.5727 Hose Clamp Socket Length: 1"(25mm) Work Safely With Hand Tools - Wear Safety Goggles

Quickly and safely removes all standard size radiator caps. Simply engage the wrench over the cap, press down and turn to release the cap.

170

Set of three service tools to aid in radiator removal and replacement. Contains: Heater Hose Slitter, Universal Radiator Petcock Socket, Radiator Hose Clamp Socket.

RADIATOR HOSE PINCH-OFF PLIERS

T

&E OOLS

Parallel Opening 36mm


No.4256 10"(250mm) Hose Pinch-Off Pliers


Eliminates the need to drain radiator or engine block. Jaws remain Eliminates the need to drain radiator or engine block. Jaws remain parallel throughout clamping range. Automatic locking ratchet system parallel throughout clamping range. Automatic locking ratchet system Maximum Opening: 1.17/16"(36mm) Jaw Length: 2.1/2"(65mm) Maximum Opening: 15/16"(23mm) Jaw Length: 2.1/2"(65mm)



No.2-4510 3Pc. Hose Pinch-Off Plier Set

Eliminates the need to drain radiator or engine block. Jaws remain parallel throughout clamping range. Automatic locking ratchet system Set of three hose pinch off pliers. Jaw Length: 2.1/2"(65mm) Maximum Opening: 1.7/8"(48mm) Includes #4254 8", #4256 10" and #4258 12" Hose Pinch-Off Pliers

No.4236 Radiator Hose Shark Tooth Pliers Remove or install radiator and heater hoses. Grips hoses securely and provides leverage to twist and remove or install the hose. Slip joint opening four large size radiator hoses. Length: 11.1/2"(290mm)

No.4250 10" Radiator Hose Pinch-Off Pliers Eliminates the need to drain radiator or engine block when servicing cooling system components, therefore saving expensive glycol based inhibitors. Pliers squeeze hoses shut, jaws swivel for parallel clamping, automatic locking ratchet. Jaw Length: 2.1/2"(65mm) Opening: 1.1/8"(28mm)

No.4102 Anti-Freeze Coolant Tester Sixth Ball Shows Over Protection Features Rugged Safety Shield The #4102 is a professional bead-type glycol specific gravity tester. Fast and easy to use, number of floating beads measures degree of protection. Temperature compensating for testing with engine hot or cold. Accurate to -34°F (-37°C) Complete with vinyl pocket protector case imprinted with instructions & specifications.

l

No.4259 12" Radiator Hose Pinch-Off Pliers Eliminates the need to drain radiator or engine block when servicing cooling system components, therefore saving expensive glycol based inhibitors. Pliers squeeze hoses shut, jaws swivel for parallel clamping, automatic locking ratchet. Jaw Length: 2.1/2"(65mm) Opening: 1.3/4"(45mm)

l

No.4107 Propylene Glycol Anti-Freeze Coolant Tester New professional model automotive anti-freeze coolant tester with propylene base. Five floating discs accurately measure protection at any temperature. Discs are temperature compensated. l 1 Disc floating = +20°F ( -7°C) l 2 Discs floating = +10°F (-12°C) l 3 Discs floating = -5°F (-21°C) l 4 Discs floating = -26°F (-32°C) l 5 Discs floating = -50°F (-46°C) TM

Super Tough Plastic Body & Plastic Dics Length: 11"(280mm) Floating Discs Show Degree of Protection


171

T

&E OOLS

No.5390 Carburettor Base Wrench Offset 10 & 12mm thin jaw open end wrench is especially designed to fit hard to reach carburettor base nuts on most late model vehicles. Length: 6.1/2"(165mm)

No.5377 Carburettor Linkage Adjusting Tool Fits both 1/8" & 5/32"(3mm to 4mm) linkages. Designed especially for precise bending of linkage rods to adjust carburettor setting. Eliminates using pliers & possible damage. Made from heat treated steel and has inside angled slot at each end for extra leverage on hard to reach linkage rods. Length: 6.1/2"(165mm)

CARBURETTOR ADJUSTMENT TOOLS

No.5392 Carburettor Base Wrench

No.5150 Carburettor Throttle Adjustment Tool

Flexible shaft adjusts RPM without disturbing original carburettor setting. Can be used without removing air cleaner. Tool holds Extra thin wall 10 & 12mm, 12 point ring spanner designed to reach under carburettor setting whilst you do tune-up, timing or air conditioning service. bodies to remove and replace anchor nuts. Length: 12"(300mm) Length: 8.1/4"(210mm)

No.5154 Universal Carburettor Feet Durable nylon feet hold carburettor steady and level on workbench. Allows free movement of linkage and throttle plates. Four feet snap together for easy storage. Length: 2.1/4"(57mm)

No.5570 5Pc. Carburettor Adjusting Tool Set

Heavy duty flexible shaft for easy access. "Double D", 1/4" & 4.5mm Single Hex & 3/32" In-hex adaptors. Bits store inside handle cavity. For adjusting idle mixture screws on most vehicles. Length: 15.1/2"(394mm)

5577 5576

5579

5578

No.5574 4Pc. Carburettor Adjusting Tool Set Contains four carburettor adjusting tools #’s 5576, 5577, 5578 & 5579 for adjusting idle mixture screws on most vehicles. Supplied in vinyl wallet. Lengths: 9.1/4"(235mm)

172

TM

No.5576 "Double D" Carburettor Adjuster

No.5578 Straight Slot Carburettor Adjuster

Used for mixture and idle adjustments on Rochester Quadrajet and Varajet carburettors with "Double D" adjustment screws. Size: 4mm x 6mm "Double D" Length: 9.1/4"(235mm)

Adjusts idle mixture screws on a wide range of early model vehicles. Tip Size: 8mm x 1mm Slotted Length: 9.1/4"(235mm)

No.5577 4.5mm Hex Carburettor Adjuster

No.5579 3/32" In-Hex Carburettor Adjuster

Socket end adjusts idle mixture screw on late model Fords, Chrysler and Asian vehicles. Size: 4.5mm Single Hex Socket Length: 9.1/4"(235mm)

Adjusts idle mixture screw on late model US and Japanese vehicles. Size: 3/32" In-Hex Bit Length: 9.1/4"(235mm)


T

&E OOLS

CARBURETTOR ADJUSTMENT TOOLS

Double "D" Tip

No.6431 Universal Carburettor Depth Gauge Essential when setting to exact specifications. Scales are engraved in both metric & imperial. l Measures all three adjustments on carburettors accurately. 1: Float level, 2: Float drop, 3: Pump rod travel. l Easy to read gauge with stainless steel rule makes depth measurements in small holes and slots. l Doubles as a protractor. l Permits easy setting of protractor angle to 30-45-60 degrees on both sides. Length: 6"(152mm)

1/4"Drive Sockets are Double D & Single Hex

No.5373 GM Computer Controlled Carburettor Sockets

For GM Varajet, Dualjet and Quadrajet carburettors. For adjusting the lean screw, idle air bleed screw, mixture control solenoid, TPS and main metering jets. Sizes: 2mm, 2.5mm, 7mm, 10mm

No.5357 Double "D" & Fish Tail Carburettor Adjusting Tool Extremely handy miniature adjuster with Double "D" end used for mixture and idle adjustments on Mikuni carburettors fitted on Mitsubishi and Toyota vehicles. The fish tail end suits Nikki and Hitachi carburettors fitted on Nissan and Subaru vehicles. Double "D" Opening: 6mm across flats Fish Tail Wings: 8mm OD Length: 2"(50mm) A

B

Double "D" Tip

Shrouded Slotted Tip

No.5376 Rochester Carburettor Adjusting Set Suits Rochester Four Barrel Carburettors This kit allows for adjustment, removal and installation of previously fixed tuning components on Rochester four barrel carburettors. For "Double D" adjustment screws. Length: 13"(330mm) l

No.XT1014 Distributor / Carburettor Adjusting Tool The 1/8" hex bit is used for Delco-Remy external adjustment distributors. The non slip shrouded slotted screwdriver adaptor is used for adjusting carburettors where obstructions hamper visual operations. Slotted Tip Size: 7mm x 1.1mm Hex Bit Size: 1/8" Length: 11"(280mm)

No.5379 Stromberg Carburettor Main Jet Tool Kit This two piece set enables installation and removal of both the main jet and access plug without having to remove carburettor from the vehicle. Length: A: 4"(100mm) Length: B: 1.1/2"(38mm)

No.5380 7Pc. Universal Carburettor Adjusting Set

5381 *

The 21"(535mm) long shaft with a 3.1/2"(90mm) flexible section permits bending of the tool to reach the most difficult of locations found on carburettors, distributors and fuel injection systems. Slim 1/4" drive head is small enough to slip between wires and other obstructions. Set includes all adaptors below marked with (*) Adjuster Length: 21"(535mm)

Available Separately No.5381 * 21"(535mm) Flexible 1/4" Drive Adjusting Tool No.5398 Shrouded Slotted Screwdriver Adaptor 9/32"(7mm) No.5382 * Shrouded Slotted Screwdriver Adaptor 5/16"(8mm) No.5397 Shrouded Slotted Screwdriver Adaptor 7/16"(11mm) 5398 5382 * 5397 5383 * No.5383 * 1/8" In-Hex Bit Adaptor GM No.5384 * 3/32" In-Hex Bit Adaptor Ford No.5385 * "Double D" Adaptor Rochester Quadrajet & Varijet No.5386 Slotted Screw Starter Adaptor 9/32"(7mm) No.5387 Magnet Adaptor, Length: 1.3/4"(43mm) Dia: 1/2"(13mm) No.5393 Slotted Screwdriver Adaptor 5/32"(4mm) No.5394 * 4.5mm Socket Adaptor (GM) No.5396 * 3mm In-Hex Bit EFI Throttle Adjuster (118mm Long) 5386 5387 5393 5385 * TM

5384 *

5394 *


5396 *

173

T

&E OOLS

CARBURETTOR ADJUSTMENT TOOLS & GAUGES

Pumps up to 30psi Has a multitude Of Uses

No.4430 Carburettor Synchronizer

For 2, 3 or 4 Carburettor Synchronization

Four individual vacuum & fuel pump pressure gauges complete with hoses and all the necessary brass fittings to enable you to check the balance and synchronization of multiple carburettors. Gauges are mounted on a fixed metal plate for easy reading. Gauge Readings: 0-30Hg(0-70cmHg) Vacuum 0-14psi(0-1.1kg/cm2) Pressure Gauge Diameter: 3.1/2"(89mm)

No.T29612 Carburettor & Electronic Fuel Injection Service Set

No.4431 Carburettor Leak Detection Tester

This kit covers most popular carburettors and fuel injection systems. Contains:

Bosch K-Tronic mixture adjustment bottom fitting, Stromberg CD and CDS tamperproof mixture adjustment on Ford CVH, Weber 0.8 x 4mm blade, Stromberg dual purpose tool, Asian and Mikuni Toyota venturi Nikki & Hitachi, Datsun & Subaru. Float needle valve spanner, Bosch L-Tronic mixture adjuster. Supplied in plastic storage case.

Unique pressure gauge with hand operated pump that enables you to test pop off pressure on carburettor seats for correct settings. By simply depressing the plunger you can pump to any pressure required up to 30psi(200kpa). Diaphragm system device gauge will ensure long and accurate usage. Gauge Diameter: 2.1/2"(65mm)

To remove PRESS & HOOK

PULL Tool holds pin or clip securely

Also great for "E" Clips

No.4357 Carburettor Pin Clip Tool Fast easy removal and installation of carburettor linkage pins. Also can be used for "E" clips and other small parts. Length: 6.7/8”(175mm)

No.T29600 Carburettor & EFI Fuel System Tool Set

For use on a wide range of models: Ford Weber, Asian, Mikuni, Nikki and Hitachi carburettors and K & L Jetronic fuel Injection. Each tool fits into the special handle and an extension piece gives improved access past air filters etc.

No.5021 Stubby Screwdriver Bit Holder Set

Extra short handle with internal 1/4" hex bit drive & 5 insert bits #1, #2 Phillips & 5/32", 7/32", 9/32" Slotted Supplied in vinyl pouch.

No.2-7182 Multi-Purpose Carburettor Adjusting Tool

Services Rochester DualJet, QuadraJet and VaraJet carburettors. Adjust lean / rich mixture screws on VaraJet carburettors. Adjust lean / rich mixture (solenoid) screw and stop screw on DualJet and QuadraJet carburettors. Large end of tool breaks seal of rich mixture stop screw on DualJet and QuadraJet carburettors. Length: 7/8"(22mm) Openings: 10.5 x 3mm Double "D" Length: 8.7/8"(225mm)

No.5020 1/4" Stubby Bit Holder Only Work Safely With Hand Tools - Wear Safety Goggles 174 TM

T

&E OOLS

ELECTRONIC FUEL INJECTION TOOLS 4436

Injector Harness Terminal Connector Release Tools

This pair of tools is designed to provide access to electrical connectors for easy disconnecting. Push and pull tools provide easy connection and removal regardless of component location. Length: 6.1/4"(160mm)

J7216

Tool Blade Electrical Component Wire Harness Connector Tool Blade

Pull Style

Electrical Component Wire Harness Connector

4436

Injector Harness Remover

The J7216 removes and installs injector wiring harness without damaging the connections. This tool saves time by not having to remove excess parts when the injector cannot be reached. Length: 9"(230mm)

J7216

J4404-4 Deluxe Fuel Line Disconnect Tool Set

3Pc. External Disconnect Tool Set to suit: VT & later Commodore, AU & later Falcon, TJ & later Magna, GM Opel & Vectra. Lengths: 1.1/4"(32mm) Plus: 7Pc. Internal Disconnect Tool Set Sizes: 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 7/8". Length: 1"(25mm) Works on all spring lock fuel line couplings fitted to today's EFI engines, also used on air conditioning lines.

J7810

4404

J4404-4

Chrysler Fuel Line Disconnect Tool

Double ended offset specially shaped Chrysler fuel line disconnect tool. Works on Chrysler 1994 and later models fitted with quick connect fuel lines. Length: 15.1/2"(395mm)

J7810

Fuel Line Disconnect Tool Set

This set is used for uncoupling quick release fittings on fuel lines. Suits: Ford, Chrysler, Renault, GM, Opel, Holden, Fiat and many other makes with quick release fittings. Sizes: 5/16"(8mm) 3/8"(10mm) + Angle Tip Length: 4.1/2"(115mm)

4412

4404

Fuel Line Disconnect Tool

This tool fits any 5/16"(8mm) or 3/8"(10mm) fuel line found on GM, Ford, Chrysler, Asian and European vehicles. Length: 4.1/8"(105mm)

4412

SFT265 Stant EFI Fuel System Tester

Thread the cap of the #SFT265 in the filler neck of tank and pump pressure to a minimum of 50in. H20 as indicated on gauge. Within two minutes you will know if the system is leak free. Works for both petrol and diesel engines. Pump is all steel construction. Gauge Diameter: 2.3/4"(70mm) Gauge Capacity: 60in H20

2-3398

3391

SFT265

EFI Pulse Tester

Performs a cylinder balance test on injectors for suspect performance. It fires individual injectors in 1/2 second increments in three different ranges: 1, 50 and 100 pulses for 500, 10 and 5 milliseconds. Power light and output light tell you when test is in activation. Includes wiring harness, injector adaptor, complete with instructions.

Fuel Injection System Tester Adaptor

Connects between multimeter / tester and wire harness connector to injector solenoid. Enables an in-line test hook up for testing resistance, voltage drop, current, pulse width, and scope pattern. TM

3391 2-3398

For Bosch Style EFI Connectors


175

T

&E OOLS

FUEL INJECTION TESTERS & ACCESSORIES Fuel Injection Test Sets 4413 Basic In-Line Fuel Injector Tester

This economy tester is used on fuel injection systems having Schrader type test valves or any other system where tester can Tee into the line. The kit comes complete with 100psi (7bar) gauge, manifold, hoses, clamps, spread clamps plus instructions. Suits: Bosch-AFC, Australian, European & Japanese MPI systems & GM - Bendix except TBI. Contents: 21002 Dual scale gauge 2.1/2"(65mm) 0 to100psi (0 to7bar) 71302 Small Parts Kit with Manifold and hose connections 71301 Standard Schrader Hose 71303 Small Schrader Hose 71304 M6 x 1.0 Hose Assembly (Honda)

4416

4413 Set

4416 Set

Universal In-Line Fuel Injector Tester

3.1/2" dual gauge (1lb. increments) includes all the metric adaptors five quick release Banjo bolt adaptors with seals & Schrader shut off valves. Also includes quick release in-line fittings plus both small & large quick release Schrader type test valves. Qty Contents: 74441 3.1/2" 100psi (7bar) Gauge & 16" hose assembly.......... 1 (No relief valve or tubing) 71317 Manifold with Quick release coupler............................... 1 41311 Quick coupler with 1/4" hose barb.................................. 1 35021 1/4" ID. x 2"(6 x 50mm) Hose....................................... 1 35031 5/16" ID. x 3"(8 x 75mm) Hose....................................... 1 41152 Hose Clamps.................................................................. 2 71318 Adaptor for standard Schrader valve.............................. 1 71319 Adaptor for small Schrader valve (Ford)......................... 1 74431 Adaptor, Banjo Bolt 6 x 1.0mm with shut off valve...... 1 74432 Adaptor, Banjo Bolt 8 x 1.0mm with shut off valve...... 1 74433 Adaptor, Banjo Bolt 10 x 1.0mm with shut off valve...... 1 74434 Adaptor, Banjo Bolt 12 x 1.25mm with shut off valve...... 1 74435 Adaptor, Banjo Bolt 12 x 1.5mm with shut off valve...... 1 52995 Blow Molded Plastic Case.............................................. 1 52010 Laminated Instruction Manual & Specification Chart ..... 1 A

4415

Throttle Body Injection Systems Kit

Contents: 21002

4415 Set with Gauge

72308-K Set without Gauge

72308 36032 41576 60236 60238 60239 72304 72305 72306 72309 74434 41152 52001

Qty 2.1/2" 60psi (4bar) Gauge & 16" Hose Assembly........... 1 Quick Release Connecting Hose Assembly................... 1 3/8" I.D. x 3"(75mm) Hose............................................. 2 Bent tubing with 3/8"UNF inverted flare nut.................... 2 Adaptor, 16 x 1.5mm Female & 3/8" tube fitting............. 2 Adaptor, 14 x 1.5mm Female & 3/8" tube fitting............. 2 Female Adaptor, 5/8"UNF & 16 x 1.5mm....................... 2 Straight tubing with 3/8" inverted flare nut..................... 2 Bent tubing with 3/8" inverted flare & 16 x 1.5mm nut... 2 Adaptor, 16 x 1.5mm male & 3/8" tube fitting................. 2 Adaptor, 14 x 1.5mm male & 3/8" tube fitting................. 2 Adaptor, banjo bolt 12 x 1.25mm with nylotron washer.. 1 Hose Clamps.................................................................. 2 Sturdy Plastic Case........................................................ 1

72308-K

Throttle Body Injection Kit (without gauge) #4415 Throttle Body Injection Systems Kit is available with #41312 quick coupler and without gauge to use with #4416 or any deluxe kit with expanded gauge. (Not Illustrated)

4450 Flow Meter Common Rail Diagnostic Set

4450 Set

176

TM

This flow meter measures rapidly and effectively the amount of fuel that each and every injector returns to the deposit tank. This in turn diagnoses the injector status and if any damage is present. Features: 1: Direct measurement of return flow of the injector. 2: Measurement of return flow using external flow meter. 3: Simultaneous measurement of up to six injectors. Full instructions with drawings and diagrams are included. Supplied in blow mold case for transportation purposes.


FUEL INJECTION TESTERS & ACCESSORIES Fuel Injection Test Sets 4414 Bosch CIS/K-Jetronic Systems Kit Contents: 21002

71408 71406 71404 60410 60440 71405 52001

T

Qty 2.1/2" 100psi (7bar) Gauge & 16" Hose Assembly........ 1 Quick Release Connecting Hose and Valve Assembly... 1 Long adaptor, 8 x 1.0mm male & 12 x 1.5mm male....... 1 Short adaptor, 8 x 1.0mm male & 12 x 1.5mm male....... 2 Adaptor, 8 x 1.0mm female & 12 x 1.5mm male............. 1 Adaptor, 10 x 1.0mm female & 12 x 1.5mm male........... 1 Adaptor, 10 x 1.0mm male & 12 x 1.5mm male.............. 1 Sturdy Plastic Case......................................................... 1

&E OOLS 4414 Set

71408-K

Bosch CIS/K-Jetronic Systems Kit (without gauge) #4414 Bosch CSI/K-Jetronic Injection Systems Kit is available with #41312 quick coupler and without gauge to use with #4416 or deluxe kit with expanded gauge.

Master Fuel Injection Test Sets 4445 Master EFI Fuel Injection Tester Kit Including TBI Systems Kit includes all the fittings for most Australian, American, European and Asian systems. The uniquely designed 3.1/2"(90mm) gauge has an expanded 1lb. Incremental dual dial for accurate reading, with a 100psi and 7Bar scale. Set includes a relief valve and 6ft(1.8m) of tubing to relieve the pressure and fuel safely. It also allows checking for sufficient fuel flow. Quick coupler connection. Includes all adaptors, hoses, fittings, Banjo bolts etc. to cover EFI systems on most Australian, American, European & Asian vehicles. Instruction manual included. l

4446

4445 Set

Two Gauge Master Fuel Injection Test Set Latest designed Master Fuel Injection Test Set features a large 3.1/2" gauge with dual readings 0 to 145psi (0 to 1000kpa) plus a low pressure 2.1/2" gauge with dual scale readings 0 to 15psi (0 to 1.0kg/cm2) The low pressure gauge enables accurate readings below 15psi. Both gauges are fitted with rubber protective boots. All adaptors, gauges and hose assemblies feature a quick coupling system for fast and efficient test connections. Includes a heavy duty release valve with bleed off hose to relieve the fuel pressure safely. It also checks for sufficient fuel flow. Includes all the necessary banjo bolts, quick release threaded adaptors, Schrader valves and hair pin adaptors needed for hook-ups on today's latest vehicles. Includes a laminated instruction book, plus a repair kit of spare copper washers, seals and neoprene o-rings. All components neatly stored in the storage tray, and sturdy blow mold storage case.

4446 Set

Tests for CIS, CISE, K-Jetronic, GM TBI, In-line & End-Of-Line Banjo Fuel Bolt Hook-Ups

74447

4ft Extension Hose with Quick Coupler

Extension hose (1/8"NPT thread) with coupler to suit all EFI sets.

4450-AC Accessory Kit For Flow Meter Common Rail Diagnostic Set

Set includes eighteen flow meter hose right angle adaptors fitted with O-rings & 6 flow meter hose connection fittings to work with #4450 Flow Meter Common Rail Diagnostic Set. Supplied in blow mold case.

TM


74447

4450-AC Set

177

T

&E OOLS

FUEL INJECTION TESTERS & ACCESSORIES Fuel Injection Adaptors, Hose Assemblies & Replacement Parts

#74438 Deluxe Gauge Hose & Bleed Off Valve

#74440 Standard Gauge Hose & Bleed Off Valve

3.1/2" 100psi(7bar) gauge with 1lb increments.

2.1/2" 100psi (7bar) gauge,16" hose with quick coupler.

#74433

#74434

Banjo Fuel Bolt Adaptor Size: 10 x 1mm Thread #71315

Banjo Fuel Bolt Adaptor Size: 12 x 1.25mm Thread #71316

(for 4413 Kit)

#71329

Multi-Vehicle Pressure Manifold

Hose Assembly Audi, VW, Volvo #71308

#71317

T-Manifold with Quick Release Coupler Use on in-line applications

Isuzu I-Tec Systems Adaptor M14 x 1.5 3/8" Inverted Flare Male and Female connections. #71302

#71301

Standard Schrader Hose Assembly (from 4413)

Small Parts Kit (from 4413)

#74485

#74493

3/8" Quick Disconnect Hose Assembly for GM #74442

3/8" Quick Disconnect Hose Assembly with Standard Schrader Test Port #74851

60 PSI Gauge & Hose for #4415 TBI Injection Systems #41327

5Pc. Banjo Fuel Bolt Adaptors Includes metric sizes, Honda, Nissan, Mitsubishi, Toyota & Asian vehicles. #74435

Banjo Fuel Bolt Adaptor Size: 12 x 1.5mm Thread #71318

Standard Schrader Valve Adaptor with Quick Release Male Coupler #71330

Hose Assembly Toyota, Geo #74471

M14 x 1.5 Banjo Bolt for CIS Systems #71303

Small Schrader Hose Assembly (from 4413) #74492

5/16" Quick Disconnect Hose Assembly with Standard Schrader Test Port #74852

#60772

TM


#74432


Ford EFI Spring Lock Adaptor GM & Ford CFI Suits: Falcon, Fairlane, LTD Hair Pin Adaptor F-150 Pick-up, 99 onwards Suits GMH & EA Falcon & on Laser, Mondeo, Telstar, Festiva #71319

#71305

Small Schrader Valve Adaptor with Quick Release Male Coupler #72308

Volvo Adaptor, 14mm LH - Jetronic #74484

Connecting Hose for GM TBI 5/16" Quick Disconnect Hose with 3/8" Inverted Flare Ends Assembly for Chrysler, Ford #74446

#74458

Bleed Off Valve and Tube Assembly 1.8m

Economy Bleed Off Valve and Tube Assembly 1.8m

#71304

#71408

M6 x 1.0 Hose Assembly (Honda) from 4413 Kit #74424

3.1/2" Expanded Gauge Assembly For Master Sets #74853

Hose & Valve Assemblyfor Bosch CIS #74425

Hose Assembly with Bleeder Hose & Valve #74459

Small Schrader Right Quick Coupler with Male Dead Head Pressure Adaptor Standard Schrader Right Suit 1/4", 5/16", 3/8" ID Hose Angle Adaptor with Coupler Angle Adaptor with Coupler Standard Schrader Fitting #74469

Female Quick Coupler Plug Male Quick Coupler Plug Conversion Adaptor for OTC Conversion Adaptor for OTC Conversion Adaptor for OTC

178

#74431

(for 4413 Kit)

Ford EFI Spring Lock Adaptor Ford CFI 5/16" Adaptor with Small Schrader Test Port with Small Schrader Test Port #79710

#74417

#71306

11mm O-Ring Adaptor for Nissan and Infiniti

#71321

16mm O-Ring Adaptor for Hyundai & Mitsubishi


FUEL INJECTION TESTERS & ACCESSORIES Fuel Injection Adaptors & Replacement Parts #41303 (3/16" Barb) #41301 (1/4" Barb)

Quick Couplers with Barb #41312 (1/8"npt) #41313 (1/4”npt)

Quick Coupler Plugs with Male Thread #36032

3/8"I.D. x 3" Length Fuel Hose #10401

2" Long Nipple 1/8"npt x 1/8"npt Male

#11302

#41304 (1/8"npt) #41306 (1/4"npt)

Quick Couplers with Female Thread #74437

O-Rings, Washers and Valves Repair Kit

Quick Couplers with Male Thread #42439

Instruction Manual and Specification Chart

#41310 (3/16" Barb) #41311 (1/4" Barb)

Quick Coupler Plugs with Barb #34021

1/4" I.D. x 2" Length Fuel Hose

Quick Coupler Plugs with Female Thread #35031

5/16" I.D. x 3" Length Fuel Hose

#11041

#11042

#41753

Stainless Steel Hose Clamp for In-line Kit

1/8"npt Female x 1/4"npt Male Reducing Bush

1/8"npt Female x 3/8"npt Male Reducing Bush

Valve Core for EFI Fittings

#10402

#10403

#10404

#11301

Street Elbow Reducing Nipple Reducing Adaptor Female Coupling 1/8"npt x 1/8"npt Female 1/8"npt Male x 1/8"npt Female 1/4"npt Male x 1/8"npt Male 1/4"npt Female x 1/8"npt Male

#12200

#12202

#12203

T-Block Adaptor Street Elbow Adaptor Adaptor 1/4"npt Female x 1/8"npt Male 1/8"npt Female x 1/8"npt Male 1/8"npt Male x 3/8"SAE Male 1/8"npt Male x 1/4"SAE Male

#12204

#12225

Inverted Flare Fitting 1/4"Female x 1/8"npt Male

Inverted Flare Fitting 3/8"Female x 1/8"npt Male

#19703

#41604

#41576

Bleed Off Valve Tee Piece #71405

Bent Tube with 3/8" Bent Tube Inverted Flare Nut x M16 x with 3/8" Inverted Flare Nut 1.5 Nut, 3/8" O-Ring Flare #71406 #72309

Male Run Tee 1/8"NPT #71404

#41315 (1/8"npt) #41314 (1/4"npt)

#41152

#11501

1" Long Nipple 1/8"npt x 1/8"npt Thread

#41307 (1/8"npt) #41305 (1/4"npt)

T

&E OOLS

#12226

Inverted Flare Fitting 1/4"Male x 1/4"npt Male

#12301

#19702

Inverted Flare Nut 3 Way Tee Piece 3/8"SAE Male x 1/8"npt Female 3 x 1/8"npt Female Threads #72305

#60410

M8 x 1.0 Female Adaptor with M12 x 1.5 Male Thread #60440

M8 x 1.0 Male Adaptor x M10 x 1.0 Male Adaptor x M8 x 1.0 Male 3" Adaptor x M14 x 1.5 Adaptor with 3/8" M10 x 1.0 Female Adaptor M12 x 1.5 Male with O-Ring M12 x 1.5 Male with O-Ring M12 x 1.5 Male with O-Ring O-Ring Flare 3/8"Tube Fitting with M12 x 1.5 Male Thread #74426 #72306 #60236 #60238 #60239

M12 x 1.0 Adaptor Honda, Pulse Dampener TM

M16 x 1.5 Adaptor with M16 x 1.5 Female Fitting 3/8" O-Ring Flare x 3/8"Tube with 3/8" Tube End

M14 x 1.5 Female Fitting with 3/8" Tube End

3/8" Inverted Flare Union with M16x1.5 Female Thread


179

T

&E OOLS

FUEL INJECTION CLEANERS & ACCESSORIES Fuel Injection Cleaners & Accessories TU470 Fuel Injection Canister Cleaner Kit

Uses shop air and injector cleaning fluid to provide an effective, fast method of cleaning injectors. Built in adjustable pressure regulator to adjust system pressure to manufacturers specifications. Gauge Diameter: 2.1/2"(64mm)

2-7000

Pro Inject-R-Kleen Fluid

Clean injectors mean cleaner running, more efficient engines with lower emissions. This fluid restores injectors to the original spray pattern and reduces intake and port deposits. Use with #TU470 Canister Contents: 16oz (455ml) Not for use as a fuel additive. (Do not pour into fuel tank)

2-7000

QS-2104-S Pressure Pack Can Adaptor with Quick Release Coupler To Suit #QS-2103 & #QS-2104 Fuel Injection Cleaner & Test Kits Enables aerosol pressure canisters to be adapted to either kit.

QS-2104-S

74459

74459

3M & Champion Adaptor

Allows T&E’s adaptors to be used with 3M & Champion cleaners.

74454

TU470 74454

OTC Conversion Adaptor Allows T&E’s adaptors to be used with OTC’s canister cleaner.

EC900A EFI System Cleaner

BEFORE

AFTER

EC900A

All in one self contained fuel system cleaner. The fuel injection system can be cleaned then the engine can be decarbonized without disconnecting the machine. The EC900 temporarily replaces the fuel system. The control panel allows the setting of duration time or the fuel injector cleaning and maintains correct fuel pressure. Just set the controls and the cleaning will be done whilst you perform other tasks. Removes built up gum deposits and soft carbon. Traditional combustion system cleaners cannot clean up carbon residue and oil on engine surfaces completely and can actually cause residue. No dangerous electrical connections, operates from workshop air supply. The fuel system cleaner comes as a beautifully presented, excellently engineered upright cart and rolls on two large diameter wheels and two swivel casters for ease of movement. A front opening door with shelves allows for storage of fittings, hoses, accessories, fluid, solvent and tools. Complete with hoses and couplers. Dimensions: 37" x 15" x 14"(940mm x 381mm x 356mm)

EC900DL

EC900DL

180

TM

Accessory Kit for EC900A EFI System Cleaner

Includes all hoses and quick coupler connections to fit most popular electronic fuel injection systems. Also includes pressure gauge, banjo fittings, disconnect and hose clamp tools. Supplied in specially designed storage case. Gauge Diameter: 3"(75mm)


T

&E OOLS

FUEL INJECTION & CARBON CLEANING KITS Fuel Injection Cleaner & Tester Sets QS-2103 Fuel Injection Cleaner & Test Kit For Use with Aerosol Pressure Canister Only

Restore lost power and performance by cleaning the deposits from fouled fuel injectors and restore the injectors to the original spray pattern. Kit includes all the hose fittings, adaptors and banjo fittings to enable connection of cleaner / tester to suit most hook-ups on EFI vehicles. Complete instructions and hook-up diagrams included. Cleaning agent aerosol canisters are available from 3M and other cleaning agent manufacturers. Gauge Diameter: 1.1/2"(32mm)

QS-2104 Fuel Injection Cleaner & Tester Kit Includes 16oz Canister for Injector Cleaning Fluid

Restore lost power and performance by cleaning the deposits from fouled fuel injectors and restoring the injectors to the original spray pattern. Most popular electronic fuel injection kit supplied with all hose fittings, adaptors and banjo fittings to suit most hook ups on EFI vehicles. Liquid filled gauge. Hoses have quick release fittings. Supplied with 16oz canister for use with any recognised injector cleaning fluid. Complete instructions & hook-up diagrams included. Gauge Diameter: 1.1/2"(32mm)

QS-2103

Engine Carbon Cleaning & Testing Sets QS-2105 Engine Carbon Cleaning Kit With Canister The Engine Carbon Cleaning Kit enables you to decarbonize and test the engine through connection to the vacuum line. Cleans and tests the following: 1. Intake Manifolds & Ports 2. Valves, Inlet & Exhaust 3. Combustion Chambers 4. Test Vacuum System Pressure

a

QS-2104

Simply connect tapered tip of blue hose to the vacuum hose of the vehicle. Read vacuum of -50CmHc range. Turn control valve on red hose to allow cleaning agent to run into vacuum system of vehicle to clean combustion chambers, valves, manifolds & ports. Gauge Diameter: 1.1/2"(32mm)

QS-2105-1

Engine Carbon Cleaner Kit Without Canister The Engine Carbon Cleaning Kit enables you to decarbonize and test the engine through connection to the vacuum line. Cleans and tests the following: 1. Intake Manifolds & Ports 2. Valves, Inlet & Exhaust 3. Combustion Chambers 4. Test Vacuum System Pressure Simply connect the tapered tip of blue hose to the vacuum hose of the vehicle. Read vacuum of -50CmHc range. Turn control valve on red hose to allow cleaning agent to run into vacuum system of vehicle to clean combustion chambers, valves, manifolds & ports. Gauge Diameter: 1.1/2"(32mm)

TM

QS-2105

QS-2105-1


181

T

&E OOLS

FUEL INJECTION NOID-LIGHT TESTERS Fuel Injection Noid-Light Sets Instantly checks all EFI harnesses for power. Simply plug Noid-Light into disassembled injector harness & turn ignition on. Flashing pulse indicates normal pulse voltage, steady or no light reveals electrical problem.

3210

3210 Set

Deluxe Noid-Light Set

Set Contains: #3201 Noid-Light

#3202 Noid-Light #3205 Noid-Light

3212

3220

3212 Set

#3203 Noid-Light #3204 Noid-Light #3206 Noid-Light

Deluxe Noid-Light & GM IAC Signal Lights

The EFI system and idle air control can be checked quickly to see if that’s where the problem lies. Bright LEDs flash, verifying that command signals are reaching the IAC motor. Includes all six noid-lights and 2 GM signal lights.

Deluxe Noid-Light & IAC Signal Lights with Fibre Optic Extension

Includes New GM PFI / BOSCH-2

Includes fibre optic extension lead for viewing from the drivers seat while testing. Includes all 7 noid lights & 2 GM signal lights.

3209

Contains:

Bosch Combination Noid-Light Set No.3202 Multipoint Fuel Injection (PFI) No.3201 Throttle Body Fuel Injection (TBI) On Card

Individual Fuel Injection Noid-Lights

3201

Bosch EFI Noid-Light

Suits Bosch port fuel injection harnesses with round pins. a

3202

Bosch EFI Noid-Light Suits Bosch EFI harnesses with flat pins.

a

3203

3209 Set

3220 Set

TBI Noid-Light Suits GM and other throttle body injection harnesses.

a

3204

Ford Probe Noid-Light Suits Ford injection harnesses with probe type connections.

a

3201

3202

3203

3205

Geo TBI Noid-Light Suits Geo TBI harnesses with flat pins.

a

3206

GM SCPI Noid-Light Suits 1996-on SPCI Sequential central port injection systems.

a

3204

3205

3206

3207

GM PFI Bosch 2 Noid-Light Suits Bosch 2 Port Fuel Injection systems with round pins.

J3050 IAC Signal Light Testers

3207

For checking the electronic control module signal that provides direction to the idle air control motor on GM vehicles with throttle body or port fuel injection systems.

J6260 Fibre Optic Noid-Light Extension Cable

J6260

Noid-light is inserted into the cup of extension cable. Connect to the vehicle wiring harness. The fibre optic cable is secured with the suction cup to the windscreen. Observe the flashing noid-light through the lens of the fibre optic cable. Length: 6ft(1.8m)

J3050 Set

4390 4390-1

4390-2 4390-3

Set Contains:

4390-1

4390-4

TM

4390-2


Spark Plug Cap Puller Suits: VW, Bora, Golf, New Beetle, Passat, Polo, Touran, Lupo, 4-Zyl, FSI, Phaeton & T4. Spark Plug Cap Puller Suits: VW, Bora, Golf, Passat, Sharan, Touareg, Phaeton & T5. Spark Plug Cap Puller Suits: VW 8,12 Cylinder engines. Spark Plug Cap Puller Suits: VW, Audi injection engines.

4390-3 4390-4 Work Safely With Hand Tools - Wear Safety Goggles

4390

182

4Pc. Ignition Spark Plug Cap Puller Set

To remove and disengage spark plugs (power final stage) on VW and Audi injection engines.

T

&E OOLS

CUMMINS DIESEL SERVICE TOOLS

No.CRW13M 13mm Cummins Injection Pump Wrench 13mm, 12 Point box wrench is used to service the injection pump mounting bolts found on 5.9L Cummins engines. Length: 8.1/4"(210mm)

No.2-5040 Cummins Injector Remover & Installer Tool Set

No.CRW716 7/16" Cummins Fuel Pump Wrench 7/16", 12 Point box end for servicing fuel pump bolts on NH Series Engines equipped with Cummins air compressors. Length: 8.1/4"(210mm)

No.2-5042 Cummins Injector Puller

Used for removing or installing fuel injectors on Cummins L10 and N14 electronically controlled engines. Two installing adaptors help prevent damage to the injector's electronic solenoid. Instructions included. Supplied in blow mold storage case. Length: 11"(280mm)

Used on a variety of injectors found in Cummins diesel engines: L-10, PDT and PTD Top Stop 855NH. The two jaw design firmly grips the injector while it is being removed by the slide hammer. Special adaptor for pulling STC injectors is included. Instructions included. Supplied in blow mold storage case. Length: 13.1/4"(336mm)

No.2-5043 Cummins Fuel Injector Remover

No.J7119 Compressor Drive Gear Puller

Kit contains a fuel injector connector tube remover and fuel injector puller. The fuel injector connector tube must be removed before removal of the injector, or both will be damaged. Application: 1998-1/2-newer Dodge pickups and vans with 5.9L 24-valve Cummins diesel turbo engine.

Here’s the solution to removing the coupling from Cummins, Compact and Bendix air compressors found on many Cummins 855 cu.In. In-line 6 cylinder engines. Split collet fits over the coupler and mechanical force does the work. Length: 6"(150mm)

No.2-7471 Cummins Engine Barring Socket The spline end is inserted into the flywheel Suits Cummins B & C Series Engines housing until it engages into the ring gear. Attach a 1/2"square drive ratchet or breaker bar to rotate engine to bring pistons to top dead centre for injector timing. Drive: 1/2"Square Length: 3.3/4"(95mm) Use with a 1/2" UNF Threaded Slide Hammer

No.B217793 Cummins Fuel Injector Puller Adaptor

No.2-7161 Cummins Engine Turning Tool The long offset bar with pins to engage into flywheel makes easy work of cranking over the Cummins 855 cubic inch diesel engines. Designed for use when bringing pistons to top dead centre for injector timing. Length: 29"(730mm)

No.A1175 Volvo Engine Camshaft Rotator

Genuine Volvo #9996956

Used to rotate engine and camshaft Removes injectors from Cummins "B" & "C" engines. for setting the timing on Volvo diesel Threads: 12mm x 1.5mm Injector Thread Length: 5.3/4"(145mm) truck engines. Can be used on: Crankshaft Pulleys Timing Gears Water Pump Pulleys Accessory Drive Pulleys

No.9527 Cummins Accessory Drive Pulley Puller

No.2-5071 Cummins Water Pump Pulley Remover and Installer

This cross block puller and replacer is designed for use on L10 & M11 Cummins Ideal for servicing crankshaft pulleys, gears & timing gears on a wide engine water pumps. range of gasoline and diesel engines including Cummins accessory Installer has thrust bearing to provide friction free pulley replacement. Spread: 1.1/2" to 5.1/4"(38mm to 133mm) drive and water pumps. Spread: 1.1/2" to 5"(38mm to 125mm) TM


183

T

&E OOLS

CUMMINS & FORD DIESEL SERVICE TOOLS

A

B

No.J7120 Cummins Drive Pulley Puller & Installer Set Two piece set for removal & installation of the accessory drive pulley on Cummins NH & NTC 855cu.in.diesel engines. Length: A: 5.1/4"(133mm) Length: B: 5.1/2"(140mm)

No.4397 Ford Diesel 7.3L Fuel Cap Remover / Replacer Allows for easy removal and installation of Ford 7.3Litre diesel fuel caps and other diesel fuel systems using the same type of configuration. Length: 3.3/8"(85mm) Slot Opening: 5mm

No.B215751 Mack Fuel Injector Nozzle Puller Adaptor Special threaded adapter for use on Mack Midliner engines. Use in conjunction with 2-7455 Nozzle Puller.

No.2-7945 Cummins Diesel Timing Tool Set

From '94-'97, Dodge used a 5.9L Cummins diesel engine with an in-line pump on its pickups, which requires this tool set to properly synchronize the engine & injector timing. Gauge Diameter: 1.1/2"(38mm)

No.9586 Ford Diesel Vacuum Pump Pulley Remover Jaws Use with the No.J7185 Power steering pump alternator pulley remover for easy pulley removal on newer Ford diesel engines. Works on Ford's 6.9L(1984-87) and 7.3L (1988 and newer) diesel engines.

No.2-5023 Ford Injector Seat Cleaner Length: 2.1/4"(57mm)

No.B218163 Ford Fuel Injector Puller Adaptor Used with a 1/2"x 20 UNF threaded shaft slide hammer. The adaptor will easily remove injectors from Ford 6.6 & 7.8 litre diesel engines with 14mm x 1.5mm injector threads. Threads: 1/2"x 20 UNF Threaded shaft 14mm x 1.5mm Injector thread Length: 2.1/4"(57mm)

Carbon buildup on injector seat surfaces prevents proper seating of new injectors. Clear away carbon deposits, avoid improper seating. Thread Size: 24mm x 2.6mm Length: 2.5/8"(67mm) A B

No.J7460 Ford Diesel Injection Pump Mounting Wrench Specially designed wrenches to get at the hard-to-reach mounting bolts holding the fuel injection pump to the engine. Suits 6.9 & 7.3 diesel engines (1983 - current ). Length: A: 7.1/4"(185mm) Length: B: 8.1/2"(216mm)

No.9585 Ford / Navistar Diesel Air Pump Pulley Puller For removing the air pump pulley on Ford/Navistar diesel engines. Fits over pulley flange. Length: 3.5/8"(92mm)

No.4448 Bosch / Lucas Diesel Injector Puller No.2-6067 Ford Diesel Injector Remover Installer Kit Used to remove and install injectors from Ford diesel engines without causing damage to the injector or the cylinder head. Suits 1994 to current Ford 3/4 & 1 Ton light trucks and vans with 7.3Litre direct injection turbocharged (DIT) diesel engine.

184

TM

Diesel Injector Puller with 8mm, 12mm and 14 mm threaded double end adaptors fitted to each end of the shaft. Assists in removal of stubborn Bosch and Lucas diesel nozzle injectors. Slide hammer action releases injectors that are difficult to remove. Adaptor Sizes: 8mm x 1.0mm, 12mm x 1.25mm, 14mm x 1.5mm Slide Hammer Weight: 2.2lb(1kg) Length: 8.1/4"(210mm) Supplied in blow mold case.


DIESEL SERVICE TOOLS - GENERAL

No.4133 6Pc. Glow Plug Socket Set

T

&E OOLS

No.2-7155A Mack Injector Nozzle Puller

3/8" Drive deep, thin universal joint sockets for removal and replacement of all popular glow plugs fitted to diesel engines.

Special leg collars slip over the studs of the injector hold down bolts with the forcing screw threading onto the injector body to easily pull No.4133-1 8mm x 72mm Long No.4133-4 12mm x 72mm Long the nozzle without damage. Includes four different size threaded No.4133-2 9mm x 72mm Long No.4133-5 14mm x 72mm Long injector adaptors plus a special adaptor for Mack Midliner engines. No.4133-3 10mm x 72mm Long No.4133-6 16mm x 72mm Long Length: 8"(205mm) Set Includes:


No.2-7455 Mac Fuel Injector Nozzle Puller

Removes and installs injector nozzles on Mac E-6 4 VH and E-9 4 VH four valve engines. Puller threads directly into the nozzle holder and the forcing screw pulls out the injector while the cylinder guide holds it steady. Includes gauge to ensure proper injector depth during installation. Length: 10.1/2"(267mm)

No.2-7121 Fuel Injector Nozzle Puller Designed to remove pencil-type fuel injector nozzles used in agricultural and construction engines. The jaws engage around the injector and the slide hammer action gives a straight even pull. Used on Case, Caterpillar, GM, John Deere, Waukesha, White diesel engines. Length: 11"(280mm) 4046

4047

No.2-7117 Caterpillar Fuel Injector Nozzle Puller Designed to remove pencil-type fuel injector nozzles used on Caterpillar engines. Bridge and forcing screw applies a straight and even pull to remove injectors without damage. Used on Caterpillar models 1100/3208 diesel engines. Length: 7"(180mm)

No.2-6083 GM Injection Pump Timing Wrench Turns the injection pump to set pump timing. Needed anytime the pump is removed when valve service is required. Wrench pins fit into holes on moulting flange of pump. Wrench enables you to service hard to reach injection pumps on GM diesel engines fitted to vans and trucks. Length: 9.1/4"(235mm)

No.4447 Diesel Engine Glow Plug Pliers

Diesel glow plug pliers have specially machined jaws with a long reach to remove and replace recessed glow plug leads, fitted on later model European diesel vehicles. Suits: Audi, BMW, Mercedes Benz & VW Length: 11.1/2"(290mm) TM

4048 4049

No.4045 4Pc. Diesel Injection Valve Sockets Contains: Four lug type injection sockets to suit European engines.

4046 4 Pin Injector Socket 4048 2 Lug Injector Socket

4047 4 Pin Uni. Injector Socket 4049 4 Lug Injector Socket

No.J7461 Fuel Injector Pump Rotating Tool The tool securely grips the front of the fuel injection pump so you can rotate it while fine tuning the system. Works on Stanadyne rotary fuel pumps found on International 6.9 & 7.3 litre engines. Length: 10.3/4"(275mm)

No.WH101A Diesel Injection System Priming Device Essential for reintroduction of fuel into fuel pump following maintenance such as fitting of new diesel filter or following drainage of fuel tank. Must be used whenever fuel system is disturbed. Length: 13"(330mm)


185

T

&E OOLS

DIESEL INJECTOR & GLOW PLUG SOCKETS See Page 148 for #J4295 14Pc. Injector & Sensor Switch Socket Set

No.J5060 30mm Detroit Diesel Injector Socket 1.3/16"(30mm) Double hex deep wall thin socket with 3/8" square drive and 7/8" external hex permits easy access in confined areas. Prevents damage to injector nozzle and its related components. Opening: 1.3/16"(30mm) Drive: 3/8"Square & 7/8"Hex Length: 3.1/8"(80mm)

No.4023 22mm Diesel Injector Socket

No.4025 27mm Open Side Diesel Injector Socket Special cut-away in deep socket to allow access to remove and replace injectors without damage to fuel lines. For removal and replacement of injectors on BMW 524 TD, Ford, VW and Mercedes diesel engines. Length: 3.1/4"(80mm)

No.4027 22mm Open Side Diesel Injector Socket

Special thin wall, deep broached opening 22mm x 1/2" drive socket for removing and replacing diesel injectors. Length: 3.1/2"(90mm)

Speical cut-away on both sides of the socket to allow access for removal and replacement of diesel injectors without damage to the fuel lines. Length: 3.1/4"(80mm)



Special cut-away in deep socket to allow access to remove and replace injectors without damage to fuel lines. For removal and replacement of injectors on diesel engines. Length: 3.1/4"(80mm)

Special cut-away in deep socket to allow access to remove and replace injectors without damage to fuel lines. For removal and replacement of injectors on diesel engines. Length: 3.1/4"(80mm)

No.2-7458 Bosch Injector Nozzle Socket

This multipurpose tool is used for removing or installing No.A1071 Bosch injector nozzles. The inner 17mm (two flats) socket Mercedes / MAN / Scania Truck Diesel holds the nozzle stationary and the 24mm 12Pt. outer Injection Valve Socket socket tightens or loosens the nozzles's gland nut. For Use on Bosch KDEL 21mm injector nozzles John Deere diesel engines. For removal and installation of diesel injection valve on MAN Length: 3"(75mm) Sizes: 17mm(Two Flats) & 24mm 12Pt. Hexagon 422 / 403, Mercedes Benz & Scania trucks. Length: 3"(75mm) 4040

4025

4027 4036

No.4020 Diesel Injector Remover Bars

These bars will pry the most stubborn injectors from the cylinder head without having to remove it from the motor. Bars are made of high grade alloy steel and are heat treated for strength. Supplied in sturdy vinyl storage pouch. Length: 12"(300mm)

No.2-6005 Diesel Glow Plug Removal

Remove damaged and stuck glow plugs on diesel engines without having to remove the cylinder head. includes 10mm and 12mm split nuts that provide added threads for pulling. Install spacer on the split nut to give solid base for extraction. Holding split nut with a wrench the glow plug is screwed from the head.

186

TM

4025

4040

No.4030

4027

4036

4Pc. Diesel Injector Socket Set

For use on: Alfa Romeo, Chrysler, BMW, Ford, VW, Mercedes, Audi, Opel, Vauxhall, Seat, Volvo, Rover, MAN and Scania. Set Contains:

Part No. 4036 4027 4025 4040


Description 22mm Open Side 6Pt. Injector Socket 22mm Open 2 Sides 12Pt. Injector Socket 27mm Open Side 12Pt. Injector Socket 28mm Open Side 12Pt. Injector Socket

Length 110mm 80mm 80mm 80mm


DIESEL TIMING & OIL PRESSURE GAUGES A

Diesel Fuel Pump Timing Tool

2-In-1 Diesel Fuel Pump Timing Tool

Suitable for use on Bosch "VE" Kikki & Nippon Denso type pumps with 8mm & 12mm pump threads, fitted to cars & light commercial vehicles. Timing tool is used in conjunction with a dial test indicator.

T

&E OOLS

Dial Test Indicator with 8mm shank

6453

a

6453

A

6454

Diesel Timing Tool

(Without Gauge)

Diesel Timing Tool

(Gauge Included)

Contact Diameters: 3/16"(5mm) Contact Lengths: 1.1/2"(38mm) & 2"(50mm) Gauge Diameter: 2"(50mm) Mounting Shank: 8mm

6466

6454

3-in-1 Bosch Timing Tool M8, M10, M12 Suitable for use on Bosch VE type fuel injection pumps. Also fits Kiki & Nippon Denso pumps. Includes adaptors & control rods: 8 x 1.0mm, 10 x 1.0mm & 12 x 1.25mm threaded adaptors.

6450

6466

Diesel Fuel Pump Timing Set This precision measuring instrument is designed for resetting the timing position on diesel engines with the following fuel pumps: Bosch, EP/VE Rotory, Kikki, Nippon Denso, Cav Roto Diesel, Top Entry fuel pumps. Applicable diesel engines: Alfa Romeo, Audi, BMW, Daihatsu, Fiat, Ford, Isuzu, Iveco, Lancia, Land Rover, Mazda, Mitsubishi, Nissan, Renault, Rover and VW etc. Gauge Diameter: 1.1/2"(38mm)

Engine & Transmission Oil Pressure Testers 4505 Diesel Transmission Modular Shift Tester

A

Allows transmission modulator shift pressure to be tested. Has large easy to read 3.1/2"(90mm) gauge. Range: 30inHg (76cmHg) Vacuum. Increments: 1inHg

4508

6450

Diesel Engine Pressure Tester Allows quick & convenient testing on fuel pump, filters, return lines, air cleaner restriction, crankcase pressure & engine oil pressure. Combines both vacuum & pressure readings that are required for diesel engine service. Instructions included. Convenient bar mounted gauge set includes: 2.1/2"(65mm) Dia. Compound Gauge Readings: 0 to 30InHg (0 to 100kpa vacuum) 0 to 15psi (0 to 100kpa pressure) 4.1/2"(115mm) Dia. Magnehelic® Gauge Readings: 0 to 60 InH2O and 0 to 15psi 2.1/2"(65mm) Dia. Pressure Gauge Readings: 0 to160psi, (0 to 1100kpa) Nylon lines are provided with 1/8" compression fittings on the end for convenient hook-up. Supplied in blow mold case.

a

a

a

a

4509

4505

4508

Diesel Engine Pressure Adaptor Set Range of adaptors needed for connecting the #4508 Diesel Engine Pressure Tester. Set supplied in plastic storage case. Adaptors included in set:

#1

#2

4509-1 Fuel Pressure at Fuel Filter Adaptor 4509-2 Fuel Pump Suction Test Adaptor 4509-3 Fuel Return Line Pressure Adaptor #4 4509-3U Fuel Return Line Pressure Adaptor 4509-4 Air Cleaner Restriction Adaptor 4509-7 Injection Pump Transfer Pressure Adaptor #7 4509-8 Engine Oil Pressure Adaptor Work Safely With Hand Tools - Wear Safety Goggles TM

#3

#3U

#8

Set No.4509

187

T

&E DIESEL INJECTOR NOZZLE & SERVICE TOOLS - GENERAL OOLS

No.2-4202 Diesel Nozzle Tester Adaptor Set

No.2-4205 Diesel Nozzle Injector Tester & Cleaner

This set expands the #2-4205 Nozlrater to troubleshoot a wide range of diesel engine injector nozzles. Includes adaptors for servicing Audi, GM, Mercedes Benz, Nissan, Toyota & VW Rabbit diesel engines. Adaptors included: A36352 Fuel line assembly, A23617, A23621, A23622, B201917, A23693 Adaptors.

With this tester you can test for leakage, "pop-off" pressure, spray pattern, and chatter. Injectors can be cleaned during the process to ensure correct spray pattern is restored. Injector adaptors are included to suit many American, European and Asian diesel cars and trucks. Gauge Diameter: 2.1/2"(63mm) Reservoir: 1500ml

Manifold Adaptor Set Used with #2-4205 Nozlrater for Caterpillar Engines

No.2-4201 Diesel Nozzle Tester Adaptor Set

This universal adaptor set includes seventeen adaptors that connect to #2-4205 Nozlrater testing unit. They suit most popular diesels found on cars, trucks, farm and construction equipment.

Individual Fittings for #2-4201 Diesel Nozzle Adaptor Set

No.2-4203 Diesel Nozzle Tester Manifold Adaptor Set

No. A36352

This special adaptor set is for Caterpillar high and low pressure capsule type nozzles, and high pressure pencil type nozzles on 1100 and 3200 series Caterpillar engines. Complete with adaptors, low pressure gauge (1000psi), cap plug and moulting brackets. For use with #2-4205 Nozlrater Tester.

A23622

A23626

Adaptor nut, 12 x 1.5mm female R.H. thread to 1/2" x 20 female L.H. thread Adaptor nut, 14 x 1.5mm female R.H. thread to 1/2" x 20 female L.H. thread Adaptor nut, 18 x 1.5mm female R.H. thread to 1/2" x 20 female L.H. thread Adaptor nut, 9/16" x 18 female R.H. thread to 1/2" x 20 female L.H. thread Adaptor nut, 5/8" x 18 female R.H. thread to 1/2" x 20 female L.H. thread

B201912

Adaptor R.H. thread to 1/2" x 20 female L.H. thread

B201913

A23621

Adaptor nut, 9/16" x 24 female R.H. thread to 1/2" x 20 female L.H. thread Straight adaptor, 1/2" x 20 male L.H. thread (Ermeto 24° and 90° seat) to 9/16" x 18 male R.H. thread Straight adaptor, 3/8" x 24 male R.H. thread (Ermeto 24° and 90° seat) to 9/16" x 18 male R.H. thread 90° Adaptor, 9/16" x 18 male R.H. thread(Ermeto 24°) to 9/16" x 18 female R.H. thread (Ermeto 24°) Straight adaptor, 9/16" x 18 male R.H. thread Ermeto 24° to 1/2" x 20 male L.H. thread (60° seat)

B208370

Banjo adaptor 9/16" x 18 male R.H. thread 24° seat

B201916

Adaptor, 9/16" x 18" male R.H. thread to 9/16" x 18 female R.H. thread ferrule. 90° Adaptor, 9/16" x 18 male R.H. thread to 9/16" x 18 female R.H. thread Straight adaptor, 14 x 1.5mm male R.H. thread (male 60° seat) to 9/16" x 18 male R.H. thread female Ermeto 24°) Straight adaptor, 1/2" x 20 male R.H. thread Ermeto 24° to 9/16" x 18 male R.H. thread female Ermeto 24°

A23623 A23624 B201917

No.2-7106 Cylinder Liner Height Gauge

This set lets you meet those exacting specifications necessary for optimum diesel engine performance. It accurately measures cylinder bore flatness and depth. The hold-down bar correctly seats the liner for accurate measurement of liner protrusion. The easy-to-read dial is in .001 inch graduations,1.000" range. Gauge Diameter: 1.1/2"(38mm)

A23693 A23692 A23617

B208369 A38279 A43468

No.4449 Glow Plug Puller & Reamer Kit

Description Fuel line assembly 9/16" x 18 RH thread with on pipe

No.B208629 Nozzle Tester Calibration Fluid

For Use in diesel injection pump testers 1: Cleans passageway between pre-combustion chamber & cylinder. and injector nozzle testers. 2: Reams & cleans bore between glow plug & combustion chambers. #2-4205 Nozlrater. 3: Extractor for timing chain tensioner on Mercedes and BMW cars. Size: 1 US Gallon(4 Litres)

188

TM


AUTOMOTIVE ENGINE SERVICE TOOLS.pdf

Recommend Documents