An American National Standard British Standard 4458
Designation: D 2500 – 05
Designation: 219/82
Standard Test Method for
Cloud Point of Petroleum Products 1 This standard is issued under the fixed designation D 2500; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript supers cript epsilon (e) indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.
1. Scope Scope* *
methanol methan ol or eth ethano anoll in the presence presence of a cat cataly alyst st to yie yield ld mono-esters and glycerin. The fuel typically may contain up to 14 different types of fatty acids that are chemically transformed into fatty acid methyl esters (FAME). biodiesel blend , n—a ble 3.1.2 biodiesel blend nd of bio biodie diesel sel fuel wit with h petroleum-based diesel fuel designated BXX, where XX is the volume % of biodiesel. 3.1.3 cloud point , n—in petroleum products and biodiesel fuels, the temperature of a liquid specimen when the smallest observable obser vable cluster of hydro hydrocarb carbon on cryst crystals als first occurs upon cooling under prescribed conditions. 3.1.3.1 Discussion—To many observers, the cluster of wax crystals looks like a patch of whitish or milky cloud, hence the name of the test method. The cloud appears when the temperature of the specimen is low enough to cause wax crystals to form. For many specimens, the crystals first form at the lower circumferential wall of the test jar where the temperature is lowest. The size and position of the cloud or cluster at the cloud point varies depending on the nature of the specimen. Some samples samp les will form lar large, ge, easi easily ly obse observabl rvable, e, clus clusters ters,, whil whilee others are barely perceptible. 3.1.3.2 Discussion—Upon cooling to temp temperat eratures ures lower than the cloud point, clusters of crystals will grow in multiple directions; for example, around the lower circumference of the test jar, towards the center of the jar, or vertically upwards. The crysta cry stals ls can develop develop int into o a rin ring g of clo cloud ud alo along ng the bottom bottom circumference, followed by extensive crystallization across the bottom of the test jar as temperature decreases. Nevertheless, the cloud point is defi defined ned as the temperat temperature ure at whi which ch the crystals first appear, not when an entire ring or full layer of wax has been formed at the bottom of the test jar. 3.1.3.3 Discussion—In general, general, it is eas easier ier to det detect ect the cloud point of samples with large clusters that form quickly, such as paraffinic samples. The contrast between the opacity of the cluster and the liquid is also sharper. In addition, small brightly-reflective spots can sometimes be observed inside the cluster when the specimen is well illuminated. For other more difficult samples, such as naphthenic, hydrocracked, and those sample sam pless who whose se col cold d flow beh behavi avior or hav havee bee been n che chemic micall ally y altered, the appearance of the first cloud can be less distinct. The rate of crystal growth is slow, the opacity contrast is weak,
1.1 This test method covers only petroleum petroleum prod products ucts and biod bi odie iese sell fu fuel elss th that at ar aree tr tran ansp spar aren entt in la laye yers rs 40 mm in thickness, and with a cloud point below 49°C. NOTE 1—The interlaboratory program consisted of petroleum products of Test Method D Method D 1500 color 1500 color of 3.5 and lower. The precisions stated in this test method may not apply to samples with ASTM color higher than 3.5.
1.2 This sta standa ndard rd does not purport purport to add addre ress ss all of the safe sa fety ty co conc ncer erns ns,, if an anyy, as asso soci ciat ated ed wi with th it itss us use. e. It is th thee responsibility of the user of this standard to establish appro priate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. 2. Referenced Documents 2.1 ASTM Standards: 2 D 1500 Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) E 1 Specification for ASTM Liquid-in-Glass Thermometers 2.2 Energy Institute Institute Standard: Standard: Specifications for IP Standard Thermometers 3 3. Terminology 3.1 Definitions of Terms Specific to This Standard: 3.1.1 biodiesel, n—a fuel comprised of mono-alkyl esters of long chain fatty acids derived from vegetable oils or animal fats, designated B100. 3.1.1.1 Discussion—Bi —Biodi odiese esell is typ typica ically lly pro produc duced ed by a reaction of vegetable oil or animal fat with an alcohol such as
1
Thiss test method Thi method is und under er the jurisdicti jurisdiction on of ASTM Committee Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.07 D02.0 7 on Flow Proper Properties. ties. Currentt edition approved July 1, 2005 Curren 2005.. Publis Published hed August 2005. Origin Originally ally approved in 1966. Last previous edition approved in 2002 as D 2500–02 1. 2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@
[email protected] astm.org. g. For For Annual Annual Book of ASTM volume information, refer to the standard’s Document Summary page on Standards volume Standards the ASTM website website.. 3 Available from Energy Institute, 61 New Cavendish St., London, England WIM 8AR. e
*A Summary of Changes section appears at the end of this standard. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1 Copyright by ASTM Int'l (all rights reserved); Wed Dec 12 12:34:15 EST 2007 Downloaded/printed Downloaded/printed by
D 2500 – 05 6.2 Thermometers, having ranges shown below and conforming to the requirements as prescribed in Specification E 1 or Specifications for IP Standard Thermometers.
and the boundary of the cluster is more diffuse. As the temperature of these specimens decrease below the cloud point, the diffuse cluster will increase in size and can form a general haze throughout. A slight haze throughout the entire sample, which slowly becomes more apparent as the temperature of the specimen decreases, can also be caused by traces of water in the specimen instead of crystal formation (see Note 4). With these difficult samples, drying the sample prior to testing can eliminate this type of interference. 3.1.3.4 Discussion—The purpose of the cloud point method is to detect the presence of the wax crystals in the specimen; however trace amounts of water and inorganic compounds may also be present. The intent of the cloud point method is to capture the temperature at which the liquids in the specimen begin to change from a single liquid phase to a two-phase system containing solid and liquid. It is not the intent of this test method to monitor the phase transition of the trace components, such as water.
Thermometer High cloud and pour Low cloud and pour
6.3 Cork , to fit the test jar, bored centrally for the test thermometer. 6.4 Jacket , metal or glass, watertight, cylindrical, flat bottom, about 115 mm in depth, with an inside diameter of 44.2 to 45.8 mm. It shall be supported free of excessive vibration and firmly in a vertical position in the cooling bath of 6.7 so that not more than 25 mm projects out of the cooling medium. 6.5 Disk , cork or felt, 6-mm thick to fit loosely inside the jacket. 6.6 Gasket , ring form, about 5 mm in thickness, to fit snugly around the outside of the test jar and loosely inside the jacket. The gasket may be made of rubber, leather, or other material that is elastic enough to cling to the test jar and hard enough to hold its shape. Its purpose is to prevent the test jar from touching the jacket. 6.7 Bath or Baths, maintained at prescribed temperatures with a firm support to hold the jacket vertical. The required bath temperatures may be maintained by refrigeration if available, otherwise by suitable freezing mixtures.
4. Summary of Test Method 4.1 The specimen is cooled at a specified rate and examined periodically. The temperature at which a cloud is first observed at the bottom of the test jar is recorded as the cloud point. 5. Significance and Use 5.1 For petroleum products and biodiesel fuels, cloud point of a petroleum product is an index of the lowest temperature of their utility for certain applications.
NOTE 2—The mixtures commonly used for temperatures down to those shown are as follows:
6. Apparatus (see Fig. 1)
Ice and water Crushed ice and sodium chloride crystals Crushed ice and calcium chloride crystals Acetone, methyl or ethyl alcohol, or petroleum naphtha chilled in a covered metal beaker with an ice-salt mixture to −12°C, then with enough solid carbon dioxide to give the desired temperature
6.1 Test Jar , clear, cylindrical glass, flat bottom, 33.2 to 34.8-mm outside diameter and 115 and 125-mm height. The inside diameter of the jar may range from 30 to 32.4 mm within the constraint that the wall thickness be no greater than 1.6 mm. The jar should be marked with a line to indicate sample height 54 6 3 mm above the inside bottom.
10°C −12°C −26°C −57°C
7. Reagents and Materials 7.1 Acetone—Technical grade acetone is suitable for the cooling bath, provided it does not leave a residue on drying. (Warning—Extremely flammable.) 7.2 Calcium Chloride—Commercial or technical grade calcium chloride is suitable. 7.3 Carbon Dioxide (Solid) or Dry Ice—A commercial grade of dry ice is suitable for use in the cooling bath. 7.4 Ethanol or Ethyl Alcohol —A commercial or technical grade of dry ethanol is suitable for the cooling bath. (Warning—Flammable. Denatured, cannot be made nontoxic.) 7.5 Methanol or Methyl Alcohol —A commercial or technical grade of dry methanol is suitable for the cooling bath. (Warning—Flammable. Vapor harmful.) 7.6 Petroleum Naphtha—A commercial or technical grade of petroleum naphtha is suitable for the cooling bath. (Warning—Combustible. Vapor harmful.) 7.7 Sodium Chloride Crystals—Commercial or technical grade sodium chloride is suitable. 7.8 Sodium Sulfate—A reagent grade of anhydrous sodium sulfate should be used when required (see Note 4).
NOTE—All dimensions are in milllimetres. FIG. 1 Apparatus for Cloud Point Test
2 Copyright by ASTM Int'l (all rights reserved); Wed Dec 12 12:34:15 EST 2007 Downloaded/printed by
Temperature Range −38 to +50°C −80 to +20°C
Thermometer Number ASTM IP 5C 1C 6C 2C
D 2500 – 05 8. Procedure
reaches the lowest specimen temperature in the range identified for the current bath in use, based on the ranges stated in Table 1. 8.7 Report the cloud point, to the nearest 1°C, at which any cloud is observed at the bottom of the test jar, which is confirmed by continued cooling.
8.1 Bring the sample to be tested to a temperature at least 14°C above the expected cloud point. Remove any moisture present by a method such as filtration through dry lintless filter paper until the oil is perfectly clear, but make such filtration at a temperature of at least 14°C above the approximate cloud point. 8.2 Pour the sample into the test jar to the level mark. 8.3 Close the test jar tightly by the cork carrying the test thermometer. Use the high cloud and pour thermometer if the expected cloud point is above −36°C and the low cloud and pour thermometer if the expected cloud point is below −36°C. Adjust the position of the cork and the thermometer so that the cork fits tightly, the thermometer and the jar are coaxial, and the thermometer bulb is resting on the bottom of the jar.
NOTE 5—A wax cloud or haze is always noted first at the bottom of the test jar where the temperature is lowest. A slight haze throughout the entire sample, which slowly becomes more apparent as the temperature is lowered, is usually due to traces of water in the oil. Generally this water haze will not interfere with the determination of the wax cloud point. In most cases of interference, filtration through dry lintless filter papers, such as described in 8.1, is sufficient. In the case of diesel fuels, however, if the haze is very dense, a fresh portion of the sample should be dried by shaking 100 mL with 5 g of anhydrous sodium sulfate for at least 5 min and then filtering through dry lintless filter paper. Given sufficient contact time, this procedure will remove or sufficiently reduce the water haze so that the wax cloud can be readily discerned. Drying and filtering should be done always at a temperature at least 14°C above the approximate cloud point but otherwise not in excess of 49°C.
NOTE 3—Liquid column separation of thermometers occasionally occurs and may escape detection. Thermometers should be checked periodically and used only if their ice points are 0 6 1°C, when the thermometer is immersed to the immersion line in an ice bath, and when the emergent column temperature does not differ significantly from 21°C. Alternatively, immerse the thermometer to a reading and correct for the resultant cooler stem temperature.
9. Report 9.1 Report the temperature recorded in 8.7 as the cloud point, Test Method D 2500.
8.4 See that the disk, gasket, and the inside of the jacket are clean and dry. Place the disk in the bottom of the jacket. The disk and jacket shall have been placed in the cooling medium a minimum of 10 min before the test jar is inserted. The use of a jacket cover while the empty jacket is cooling is permitted. Place the gasket around the test jar, 25 mm from the bottom. Insert the test jar in the jacket. Never place a jar directly into the cooling medium.
10. Precision and Bias 10.1 The precision of this test method as determined by statistical examination of interlaboratory results is as follows: 10.1.1 Repeatability—The difference between two test results, obtained by the same operator with the same apparatus under constant operating conditions on identical test material, would in the long run, in the normal and correct operation of this test method, exceed 2°C only in 1 case in 20. 10.1.2 Reproducibility —The difference between two single and independent results obtained by different operators working in different laboratories on identical test material, would in the long run, in the normal and correct operation of this test method, exceed 4°C only in 1 case in 20. 10.1.3 The precision statements were derived from a 1990 interlaboratory cooperative test program. 4 Participants analyzed 13 sample sets comprised of various distillate fuels and lubricating oils with temperature range from -1 to -37°C. Eight laboratories participated with the manual D 2500/IP219 test method. Information on the type of samples and their average cloud points are in the research report. 10.2 Bias—The procedure in this test method has no bias, because the value of cloud point can be defined only in terms of a test method. 10.3 Precision for Biodiesel Products5—The precision of this test method as determined by statistical examination of interlaboratory results is as follows: 10.3.1 Repeatability for Blends of Biodiesel in Diesel —The difference between successive test results obtained by the same operator, using the same apparatus, under constant operating
NOTE 4—Failure to keep the disk, gasket, and the inside of the jacket clean and dry may lead to frost formation, which may cause erroneous results.
8.5 Maintain the temperature of the cooling bath at 0 6 1.5°C. 8.6 At each test thermometer reading that is a multiple of 1°C, remove the test jar from the jacket quickly but without disturbing the specimen, inspect for cloud, and replace in the jacket. This complete operation shall require not more than 3 s. If the oil does not show a cloud when it has been cooled to 9°C, transfer the test jar to a jacket in a second bath maintained at a temperature of −18 6 1.5°C (see Table 1). Do not transfer the jacket. If the specimen does not show a cloud when it has been cooled to −6°C, transfer the test jar to a jacket in a third bath maintained at a temperature of −33 6 1.5°C. For the determination of very low cloud points, additional baths are required, each bath to be maintained in accordance with Table 1. In each case, transfer the jar to the next bath, if the specimen does not exhibit cloud point and the temperature of the specimen TABLE 1 Bath and Sample Temperature Ranges Bath
Bath Temperature Setting, °C
Sample Temperature Range, °C
1 2 3 4 5
0 6 1.5 −18 6 1.5 –33 6 1.5 −51 6 1.5 −69 6 1.5
Start to 9 9 to −6 −6 to −24 −24 to −42 −42 to −60
4 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR: D02–1444. 5 Supporting data (the results of the 2001 interlaboratory cooperative test program) have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR: D02–1524.
3 Copyright by ASTM Int'l (all rights reserved); Wed Dec 12 12:34:15 EST 2007 Downloaded/printed by
D 2500 – 05 conditions, on identical test material would, in the long run, in the normal and correct operation of this test method, exceed 2°C only in 1 case in 20. 10.3.2 Reproducibility for Blends of Biodiesel in Diesel — The difference between two single and independent test results obtained by different operators, working in different laboratories, on identical test material would, in the long run, in the normal and correct operation of this test method, exceed 3°C only in 1 case in 20.
NOTE 7—One of the outcomes of the interlaboratory study was the selection of the sample types, since the ones used in the study contributed to a difficulty in determining the precision statement. Kerosene is a sufficiently different fuel type from biodiesel to cause some slight separation of phases upon cooling when in B20 blends. Also, the particular kerosene sample used was atypical, which complicated the study further. Therefore, data from the blends of kerosene in biodiesel were not used in the precision statement. In addition, the diesel fuel used in the research report was high cloud point material. Due to the cloud point of the base diesel material, this temperature range in the precision statement was limited.
NOTE 6—The precision for blends of biodiesel in diesel samples comprised cloud points from about −2 to +10°C.
NOTE 8—A future interlaboratory cloud study will be done to include a wider range of base biodiesel fuels with various distillate blend stocks.
10.3.3 The precision statements were derived from a 2001 interlaboratory cooperative test program. 5 Participants analyzed eleven sample sets comprised of different blends of two petroleum distillate fuels, diesel and kerosene, with various biodiesel fuels with temperature range from +10 to −45°C. Ten laboratories participated with the manual D 2500/IP219 test method. Information on the type of samples and their average cloud points are in the research report.
10.4 Bias for Biodiesel Products5—The procedure in this test method has no bias, because the value of cloud point can be defined only in terms of a test method. 11. Keywords 11.1 cloud point; petroleum products; wax crystals
SUMMARY OF CHANGES Subcommittee D02.07 has identified the location of selected changes to this standard since the last issue, D 2500–02 1, that may impact the use of this standard. e
(1) Added a discussion to the definition of cloud point (3.1.3). ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or
[email protected] (e-mail); or through the ASTM website (www.astm.org).
4 Copyright by ASTM Int'l (all rights reserved); Wed Dec 12 12:34:15 EST 2007 Downloaded/printed by
