CS350 Installation Instructions
This manual contains installation details for the CS350 control panels. It provides the basic programming and installation information required by technicians and engineers.
14 1791 999
1
2
14 1791 999
2
14 1791 999
CONTENTS FEATURES ................................ ................................................. ................................. ................................. .................................. ................................. ................................. ................. 3 KEYPAD INSTALLATION ...................................... ......................................................... ...................................... ...................................... ............................... ............ 4-5 WIRING SPECIFICATIONS .................................. .................................................... ................................... ................................... ................................... .................... ... 5 POWERING UP PANEL ................................... .................................................... .................................. .................................. .................................. ........................... .......... 6 HOW TO PROGRAMME .................................. ................................................... .................................. .................................. .................................. ........................... .......... 7 PROGRAMMING MAP ..................................... ........................................................ ...................................... ..................................... ....................................... ....................... 8 PROGRAMMING FUNCTIONS ............................................ ................................................................... ............................................. ................................ .......... 11 PERIDIAX FEATURE ..................................... ......................................................... ....................................... ....................................... ...................................... .................... 19 PROGRAMMING TEXT .......................................... .............................................................. ....................................... .................................... .............................. ............. 20 RETURNING TO FACTORY DEFAULT ................................................. ........................................................................... ..................................... ........... 21 QUICK CODES ................................. .................................................. ................................... ................................... .................................. .................................... ...................... ... 21 ZONE WIRING OPTIONS ................................. .................................................. ................................. ................................. .................................. ......................... ........ 22 WIRING OF SIRENS ................................ ................................................ ................................ ................................. ................................. ................................... ................... 23 WIRING OF OUTPUTS RELAYS ............................. ............................................ .............................. .............................. ............................... ............................... .............................. .................. ... 24 DIGITAL COMMUNICATORS ............................................. ..................................................................... ............................................ .................... 24 FIRE DETECTORS ................................... ..................................................... ..................................... ..................................... ................................. ............... 24 LIST WITH SHORT CODES ................................... ..................................................... ..................................... ..................................... ................................ .............. 25 DEFAULT CHART .................................... ....................................................... ..................................... .................................... ..................................... ............................. .......... 26 PROBLEM SOLVING .................................... ...................................................... .................................... .................................... .................................... ......................... ....... 27 TECHNICAL SPECIFICATION .......................................... ............................................................... .......................................... ..................................... ................ 29 MAIN PANEL WIRING DIAGRAM ..................................... ........................................................ ....................................... ....................................... ................... 30
Features FEATURES The CS350 is a microcomputer based alarm control panel operating from remote keypads, and has the following features: l
Facility for up to 4 CD3008 remote keypads... one CD3008 is supplied with the panel.
l
6 freely programmable dual zones.
l
Auxiliary tamper input.
l
Supervised bell tamper input.
l
Digital communicator fault input... reprogrammable to include remote engineer reset.
l
New perimeter system capability which provides local alarms for perimeter zone activations. This can reduce false alarms considerably. Exremely useful with inertia shock sensors.
l
4 freely programmable open collector outputs.
l
2 freely programmable high current outputs (eg. to control sirens).
l
LCD with freely programmable zone names... up to 12 characters.
l l
Battery input monitored. Four user codes.
See Programming Functions on page 14 for zone (Input) and page 15 for output types. 14 1791 999
3
Keypad Installation
3
CD3008
LIFT
2 PUSH
PUSH IN CLIP WITH SCREW DRIVER AND LIFT UP LID
REMOVE SCREW IF FITTED
1
Figure 1.
CD3008 ADJUSTMENT DISPLAY-CONTRAST
DIPSWITCHES FOR KEYPAD ID
CABLE ENTRY FROM TOP MOUNTING HOLE
MIN
MAX
ON
1
MOUNTING HOLE
PUSH CLAMP GENTLY TO REMOVE PCB
SD
2
3
4
CABLE ENTRY FROM BACK
SPARE SCREW TO FIX COVER ONTO BASE
D C B A
MOUNTING HOLE CABLE ENTRY FROM BOTTOM
Figure 2.
4
14 1791 999
Keypad Installation
SW1 MIN
MAX
ON 1
SD
2
3
4
ON
Control panel Terminal 5 D C B A
15 14 13 12
OFF 1
2
3
4
1
Keypad 1 (all off)
2
3
4
Keypad 2
ON OFF 1
CD3008
2
3
4
Keypad 3
Figure 3.
1
2
3
4
Keypad 4
Figure 4.
Wiring Specifications Connect the additional keypads either using a STAR or MULTIDROP configuration. MULTIDROP STAR
the keypads are 'daisy chained' together, each keypad being connected in parallel to the one before it. each keypad is wired back separately to the control panel terminals.
Any combination of the above wiring methods is allowed with the restriction that the total cable length on each of the wiring loops (either multidrop or star) is restricted to 100m. The following diagram shows how 4 RKPs may be connected using both methods.
Figure 5.
14 1791 999
5
Powering Up Panel
Connection of the control panel and the remote keypad in the following sequence allows the engin eer to establish that the control panel is working correctly. Connection sequence: 1. Before installing the remote keypad (RKP) at it's designated position, it may be connected at the control panel, to enable the engineer to commission the system. 2. Check that the ID for the RKP is set correctly... one keypad has to have ID1 (refer to Diagram 2). 3. Connect the RKP to the panel as shown in Diagram 3. 4. Replace the cover of the RKP and ensure that the tamper switch in the panel is closed. 5. Apply mains power to the panel. The system will power up in armed state (Factory Programme Setting). If any zones are open at power up, the audibles will activate. The panel defaults to the language select prompt when switched on for the first time [ UK/IRL Press é 1]. Enter [ é] and [1] to select English language. Note that this also happens after returning to factory default. See page 21 for more details. 6. Enter the Default User Security Code [1][1][2][2] at the keypad to disarm the system. The keypad display shows DISARMING and the audibles, if sounding, will stop. Display then shows any zones which are open and caused it to alarm. If [0] key is pressed at this stage, the display will show FINISHED? . Enter ACCEPT [ü] to finish with operator menu. 7. The display shows Time/Date and the system is now disarmed. 8. Enter [1][2][7][8] (Default Engineer Code) to enter Engineer Mode and to change programme parameters. See the Programming Map and Programming Functions for operational details. How to programme is detailed on page 7. 9. Each time the system is powered down the panel memorizes it's current state, i.e. whether armed, disarmed, partguard, etc. and will restore to that state when powered-up again.
6
14 1791 999
HOW TO PROGRAMME All programmed features can be changed. The structure and position of the programming options are illustrated in the Programming Map on the next page. Features and options are grouped togeth er and allocated to 6 main menu blocks:
1 MAINTENANCE
4 ZONES
2 TIMERS
5 OUTPUTS/REMOTES
3 USERS
6 MISCELLANEOUS
Once in Engineer Mode, the blocks can be accessed by 'stepping' through the menu blocks and accepting the option shown in the display. The keys used for programme selections are defined as follows: [ê] [é] [ü] [X]
stepping forward to next block or programming option returning to previous block or programming option enter programming block - enter programming option - confirm changes - accept option quit programming block - quit programming option - reject changes
PROGRAMMING EXAMPLE Adding Additional Keypads After have installed the additional keypads - mind the correct dipswitch ID setting - go to the Engineer Programming Mode and proceed as follows: 1. Use the [ê] key till OUTPUTS/REMOTES is displayed then enter [ü] . 2. Use the [ê] key till INSTALL REMOTE is displayed then enter [ü] . 3. The display shows the keypads connected, eg. REMOTE k k ✱ ✱ . Confirm [ü] these changes when they are correct. If not correct, verify the wiring to the keypad and dipswitch ID settings. The keypad must be powerless when changing dipswitch settings. 4. The display now shows INSTALL REMOTE . Quit programming blocks [X] till GOODBYE is displayed. Now accept [ü] to leave the Engineer Programming Mode.
14 1791 999
7
CS350 PROGRAMMIMG MAP V1.0 1
MAINTENANCE
1
Engineer Log
Display Log Clear Log Maintenance Menu
2
Output Test
nn Low or nn High
3
Show Open Zones
All Closed or nn Zone
4
Walk Test
Walk Test nn
5
LED Test
Testing LEDs
Main Menu
2
1
Entry Time nn
2
Exit Time nn
3
Split Time OFF/ON
4
Bell Times
5
Time hh:mm
Time hh:mm
6
Date dd/mm/yy
Date dd/mm/yy
7
Summertime
Forward Date Backward Date Summertime ON/OFF Timers Menu
TIMERS
Main Menu
3
2
1
Change Codes xx Code Unused New Code Verify Error
xx Code In Use
Code Privilege
01 Fs Us . . . . . . OK 02 . . . . . . . . . . . OK 03 . . . . . . . . . . . OK 04 . . . . . . . . . . . OK Leave this
USER ATTRIBUTES
USERS
8
Bell Cutout nn Bel Delay nn All Bells Cut ON/OFF Dig Cutout ON/OFF Perim.Bell Cutout nn Timers Menu
3
Engineer Code
New Code Verify Error
4
Duress Code
New Code Verify Error
5
Code Count nn
6
êêOpen Zones ON/OFF Main Menu
Mn=Manager In=Inhibit Ps=Part Set Us=Unset Fs=Full Set
14 1791 999
CS350 Programming Map
4
ZONES
1
Zone Type
01 Alarm 0x . . . . . . . . . . . . 06 . . . . . . . . . . . . Leave this
2
Zone Attributes
01 In 0x . . . . . . . . . . . . 06 . . . . . . . . . . . . Leave this
3
Shock Zones
nn Gross. x Pls y nn Wrong Type
4
Zone Name
5
Loop Type : Alarm Loop Type : Dual
ZONE TYPES Unused Tamper PA Key Fire Exit/Entry Alarm Keypad Lock Key Inf=Infinite Entry Exit Trm=Exit Terminator ZONE ATTRIBUTES Ls=Local Alarm Shock La=Local Alarm Contact In=Inhibit 24=24 hours Pg=Partguard So=Soak Test Ac=Access Ch=Chime KEY ZONE ATTRIBUTES Fs=Full Set Ps=Part Set Us=Unset Pu=Pulsed Qs=Quick Set
Main Menu
5
OUTPUTS / REMOTES
1
2
Output Type
Install Remote
01 Disarm/Arm 0x . . . . . . . . . . . . 06 . . . . . . . . . . . .
Remote kk** k=CD3008
Main Menu
14 1791 999
OUTPUT TYPES Disarm/Arm Alarm P.A. Fire Tamper Latch Fire Detect Reset Buzzer Int.Bell Ext.Bell Partguard System Clear Trouble Perim.Alarm Unused Clear
9
CS350 Programming Map
6
1
Arm/Disarm Menu
User Walk ON/OFF Forced Arm Opts Rearm Options ArmedDisplay ON/OFF Exit Fault Buzzer/Bell Final Door ON/OFF Miscellaneous Menu
2
P.A. Menu
P.A. Silent/Bells PA, LF Silent/Bells éê PA ON/OFF Miscellaneous Menu
3
Partgd/Chime
Timed Partgd ON/OFF Access>EE/Access Partgd Digi ON/OFF Latched Chime ON/OFF Int.Bell Chime ON/OFF Miscellaneous Menu
4
Eng. Reset Menu
Reset Code/FTC or Code Only P.A. Reset ON/OFF Tamper Reset ON/OFF Alarm Reset ON/OFF Clear Engineer Reset Miscellaneous Menu
5
Warnings
PF Buzzer ON/OFF LF Buzzer ON/OFF Miscellaneous Menu
6
Factory Prog Menu
Engineer Lock ON/OFF Miscellaneous Menu
7
Change Language
English Nederlands Francais Italiano
8
SysClear Inputs
System Clear Mains ON/OFF System Clear Battery ON/OFF System Clear Fuse ON/OFF System Clear Accs+EE ON/OFF Miscellaneous Menu
MISCELLANEOUS
Main Menu
No Forced Arming Keep Inhibits Clear when closed Clear after exit
Always rearm Never rearm Rearm 1 to 8 Times
GOODBYE
10
14 1791 999
CS350 Programming Functions 1. MAINTENANCE MENU 1.1 Engineer Log 1.1.1 Display Log Use this function to consult the 40 event log
Engineer Log
1.1.2 Clear Log Will clear all events in the Engineer Log 1.2 Output Test Use the [é ] and [ê ] keys to select the desired output. Use the [ ü] key to toggle the output polarity. Will return to its programmed status when you move to the next output.
Output Test
1.3 Show Open Zones Will show any zone which is open. This is a useful test function.
Show open zones
1.4 Walk Test Used to test individual inputs. Triggering the input will activate the interior bell for 4 seconds,as well as latch and walk test outputs.
Walk Test
1.5 Led Test This option will perform a sequential test of all keypad LED's
Led Test
2. TIMERS 2.1 Entry Time Programmable between 0 to 99 seconds.
Entry Time
2.2 Exit Time Programmable between 0 to 99 seconds.
Exit Time
2.3 Split Entry Time When this option is set and the entry time is exceeded, th en only the interior bells will sound. Only after the additional entry time expired, which is half the time programmed in 2.1, will a full alarm be created. 2.4 Bell Times 2.4.1 Bell Cutout Programmable between 0-99 minutes for exterior bell. When a time limit is required for interior bell then see 2.4.3.
Split Entry Time
Bell Times
2.4.2 Bell Delay Programmed delay in minutes for interior and exterior bells which becomes operational only when the system is set and no digi fault condition prevails (negative to terminal 20). 2.4.3 All Bells Cut Select for ON if interior bell must be timed for duration of 'Bell Cutout' time 14 1791 999
11
CS350 Programming Functions 2.4.4 Digi Cutout Select for ON if the output type 'Alarm' must reset with the Bell cutout time. If set to OFF then this output resets when the system is disarmed.
Bell Times
2.4.5 Perimeter Bell Cutout Programmed alarm time in minutes for the 'Perim.Alarm' output type. The exterior bell and Perimeter bell output types will reset after this time alarm expired. See also Peridiax feature on page 19. Time 2.5 Time Programme time in Hours and Minutes:
hh:mm Date
2.6 Date Programme date:
dd / mm / yy
2.7 Summertime 2.7.1 Forward date Date at which clock is advanced with 1 hour (start of summertime). 2.7.2 Backward date Date at which clock is returned with 1 hour (start of wintertime). 2.7.3 Summertime ON/OFF Select for ON if automatic correction to summertime is required. 3. Users 3.1 Change Codes Programme here user code 01 to 04. Use from 4 up to 6 digits with the exception of '0'. Deleting a code is achieved by entering [ü] after appearance of [New code _ ]. Code 4 can be used with a code counter (see 3.5). Factory default code for user code01is [1122].
Change Codes
Code Privileges
3.2 Code Privileges Allocate operational functions to each code. Attribute . Mn
Function change codes, time, date, read engineeer memory, access to chime function . In inhibit zones . Ps part set of system . Us unset of system . Fs full set of system 3.3 Engineer Code Programme here new Engineer code. Factory default is [1278]. 12
Engineer Code
14 1791 999
CS350 Programming Functions 3.4 Duress Code Programme here the code which will disarm the panel and activate the Personal Attack output. The output restores after entering a user code.
Duress Code
Code Count 3.5 Code Count Programme the amount of times code 4 can be introduced. When set to '99' code 4 is always operational. Setting to '0' disables the code. Open Zones 3.6 êêOpen Zones On/Off When this option is programmed to 'On' then a keyswitch user will be able to view any open zones by pushing twice the [ê ] button. Quick Codes Off 3.7 Quick codes On/Off When this option is programmed to 'On' it is possible to fast arm the panel. The following three keystroke sequences are possible : [0] [ê] [4] Arms system with exit time. [0] [ê] [5] Arms system immediately (no exit time). [0] [ê] [7] Arms system partially (Part Set). Zone Type 4. ZONES 4.1 Zone Type Define here the typical function of each input. TYPE FUNCTION . Unused Input is not operational . Tamper Input is 24Hrs operational. Activation of input causes 'internal bell' alarm in disarmed state and full alarm in armed state. The input is automatically bypassed after an alarm till the second valid entry of a user code. output : tamper, alarm, int.bell, ext.bell, system clear, fire reset . P.A. Input is 24Hrs operational. Silent or audible Personal Attack alarm is determined in function 6.2.1. output : P.A., system clear, fire reset . Key Input is 24Hrs operational to arm/disarm system. The exact operation will be determined by the attributes allocated in function 4.2. Use Pulse keyswitches if more than one input is to be used as Key zone. output : disarm/arm, buzzer, latch . Fire Input is 24Hrs operational. Activation of zone will cause the sirens to pulse on and of. The input is automatically bypassed after an alarm till the second entry of a valid user code. output : fire, interior bell, exterior bell, system clear, fire reset 14 1791 999
13
CS350 Programming Functions TYPE . Exit/Entry
FUNCTION
Zone Type
Input is bypassed during exit time when arming the system. If after the exit time the zone is still open, the panel will not arm and act as programmed in function 6.1.5. During the entry procedure the entry timeris started which allows disarming. output : buzzer, alarm, interior bell, exterior bell, fire reset
. Alarm
Input is only active when the system is armed and it will act according to its programmed attributes. outputs : alarm, interior bell, exterior bell, system clear, fire reset
. Keypad Lock opening this input will disable access to the keypad. . Key Infinite creates an infinite exit time. Only after opening and closing this zone will the panel arm after four seconds. Re-activation starts an infinite entry time. . Exit
The exit time stops and system arms 4 seconds after Terminator closing the input. Zone Attributes
4.2 Zone Attributes Attributes define the operation of the zone type. Some types have attributes inherent to them. Others can not be changed which will be displayed by [No Option]. ATTRIBUTE FUNCTION . In Allows inhibiting of alarm and exit/entry zones . 24 Creates a 24Hrs zone. Only applicable for Alarm types. . Pg Partguard . Zone is inhibited during partguard protection. . So Soak Test . The related input will not activate any alarm output but only log its events. . Ac Access zone. Follows the exit/entry input. Will create a direct alarm when triggered prior to the exit/entry input, except if programmed for Access/EE and the panel is in Partguard mode (see function 6.3.2.). . Ch Chime. Input activates buzzer/ interior bell when in disarmed state. . Ls Local Shock . Shock sensor alarm triggers 'perimeter' output instead of 'alarm' output. See also Peridiax programming on p.19. . La Local Alarm. Both shock sensor and/or contact activation will trigger the perimeter output. See also Peridiax programming on p.19.
14
Key Zones
14 1791 999
CS350 Programming Functions KEY ZONE ATTRIBUTES . Fs . Ps . Us . Pu
. Qs
Full set . Keyswitch fully arms system. Part set . Keyswitch partially arms system. Unset .Keyswitch disarms system. Pulse.Keyswitch used must be a pulse type. Allows arming/disarming with multiple keyswitches in a system. Quick set . Keyswitch arms panel without exit time.
4.3 Shock Zones Input 1 to 4 can be programmed to analyse enertia shocks (e.g. GS610). Two types of attack can be calibrated for. Heavy attacks ( 'gross' level) and small repetitive attacks ('pulse' count). The pulse count ismonitored after the first triggering in a window of 30s with 1s intervals. 4.4 Zone Names Programme here personalised names for each input. (See page. 20 for example.) 4.5 Loop Type Inputs can be configured to detect alarm contact activations only ('Alarm') or alarm and tamper violations within the same loop ('Dual').
Zone Attributes
Shock Zones
Zone Names
Loop Type : Alarm
Output Type
5. OUTPUTS / REMOTES 5.1 Output Type Define here the typical function of each output (1 to 6). TYPE FUNCTION . Disarm/Arm Reflects the control panel's arm/disarm status. . Alarm Switches with intrusion and tamper alarm (Tamper only when armed). . PA Switches with PA alarm and / or Duress alarm. . Fire Switches with a fire alarm. . Tamper Switches with a 24Hrs and / or a tamper alarm. . Latch Switches after exit time and / or walk test. Resets with disarm or start of entry time. Used withlatching sensors. . Fire Reset Switches with second entry of a valid user code after an alarm or after leaving the user log. . Buzzer Follows the buzzer operation of the keypad. . Interior Bell Follows the interior bell status. . Exterior Bell Follows the exterior bell alarm time. . Partguard Switches when control panel is part set. . System Clear Reflects the system status according to the optionsprogrammed in function 6.8. . Trouble Indicates a system error : E²PROM error, line fault, RKP fault, low battery, mains failure. The RKP will display the cause of trouble. 14 1791 999
15
CS350 Programming Functions TYPE . A Alarm
. Unused
FUNCTION Switches with a perimeter alarm for the duration as programmed in function 2.4.5. In this case the exterior bell follows the A Alarm. Output is not used.
5.2 Install Remotes Only one keypad is installed when the panel is powered-up from factory default. Additional keypads must be initialised by the panel before they become active. When selecting [ ü] install remotes, the display will show the keypads which it recognizes, for example two keypads: [Remote kk**]. Now enter [ü] again to initialize the other keypad(s). 6. MISCELLANEOUS 6.1 Arm / Disarm Menu Programming of options associated with arming / disarming. 6.1.1 User Walk On/Off When an input is open during arming of the panel, the interior bell will give a short activation each time a zone is closed.
. . .
.
Output Type
Install Remotes
Arm/Disarm Menu
6.1.2 Forced Arm Opts Determine here the' forced arming' conditions. Input(s) and code(s) must have the 'In' attribute to be able to force arming of the panel. Forced arming can be achieved in three ways. a) Go to the [Forced Arm ] menu in the user mode and accept. b) Arm the panel and enter [éé] when the display shows [Open Zone(s)]. c) Arm the panel with a keyswitch while a 'forced arm' option has been programmed. Option Operation No forced arming Forced arming is not possible. Keep inhibits Open zones are omitted till the panel is disarmed. Clear when closed Open zones are omitted till they close again. From that moment on they can detect again. Clear after exit Open zones are omitted till the exit time has expired, after which they can detect again.
6.1.3 Rearm Options Define the condition of retriggering of bells. Option Operation . Always Rearm The same input when activated, will al ways retrigger sirens. . Never Rearm The same input will not re-trigger the sirens. . Rearm 1 to 8 times Limits the number of re-triggerings as programmed. 16
14 1791 999
CS350 Programming Functions
6.1.4 Armed Display On / Off Determines if the display will show the armed status or time & date when armed.
Armd/Disarm Menu
6.1.5 Exit Fault Buzzer/Bell Deterines if the buzzer only or buzzer + interior bell will activate with an exit fault. 6.1.6 Final Door On / Off After introducing the code, the panel will arm 4s. after having opened and closed the exit zone or access zone even before the exit time has expired. P.A. Menu 6.2 P.A. Menu 6.2.1 P.A. Silent/Bells Programme if a PA alarm must be silent or loud. 6.2.2 PA,LF Silent/Bells Programme if a PA alarm must be silent or loud when a phone line fault is present. 6.2.3 éê PA On/Off Programme if the keypad panic buttons are operational or not. Partguard/Chime 6.3 Partguard / Chime 6.3.1 Timed Partguard On/Off Define if the panel is armed with or without exit time. 6.3.2 Access zones with Partguard Define if an access zone becomes an entry/ exit zone when partially armed or not. 6.3.3 Partguard Digi On/Off Define if the alarm output operates when partially armed or not. 6.3.4 Latched Chime On/Off If Latched Chime is set to On, the chime will remain operational each time the system is disarmed untill manually canceled by user. 6.3.5 Interior Bell Chime On/Off Define if the interior bell follows the chime function or not. Engineer reset 6.4 Engineer reset menu Define the conditions which will call for an engineer reset. When a panel asks for [Call Engineer nn], were nn is a number, the user can't arm his panel. 6.4.1 Reset Code/FTC input or Code only When made negative,Input 20 (Fail To Communicate or Digi Fault) may be used to clear engineer reset. When only a code is allowed to reset, programme for [Reset Code Only]. 14 1791 999
17
CS350 Programming Functions
6.4.2 P.A. Reset On/Off Define if PA alarm requires engineer reset or not.
P.A. Menu
6.4.3 Tamper Reset On/Off Define if Tamper alarm requires engineer reset or not. 6.4.4 Alarm Reset On/Off Define if Alarm type input (including Tamper when armed) requires engineer reset or not. 6.4.5 Clear Engineer Reset Clear an engineer reset request. [Reset Cleared !] will be displayed. Warnings 6.5 Warnings 6.5.1 PF Buzzer On/Off Define if a 230V mains failure must trigger the buzzer output. 6.5.2 LF Buzzer On/Off Define if a Digi Fault (via input 20) must trigger the buzzer output. Engnr. Lock Off 6.6 Engineer Lock Define if an engineer code is required to factory default the panel. See also the chapter returning to factory default. Change Language 6.7 Change Language Change the language used by the panel to Dutch, Fren ch or Italian. 6.8 System Clear Inputs Define the parameters which will determine the function of the System Clear output.
System Clear Inputs
6.8.1 System Clear Mains On/Off Will a 230V mains failure switch the output off or not. 6.8.2 System Clear Battery On/Off Will a battery failure switch the output off or not. 6.8.3 System Clear Fuse On/Off Will a fuse failure switch the output off or not. 6.8.4 System Clear Access + EE On/Off Will an open access or EE zone switch the output off or not.
18
14 1791 999
Peridiax Feature The CS3503 control panel has been equipped with Aritech's new Perimeter and Dialler eXtended programming option. How It Works When the panel is armed and not in alarm state, activating a perimeter zone will cause a PerimeterAlarm or Local Alarm. This means that both internal and external bells sound for a programmable number of minutes (perimeter bell time). l A Perimeter Alarm digi output will turn on and reset at the end of the perimeter bell cutout time. l The main alarm digi will not turn on. Engineer reset and rearm option are not activated by Perimeter-Alarm. l l Perimeter-Alarms that occur during exit time, after silent PA etc. are treated like normal alarms. Perimeter-Alarms that occur during bell delay/cutout will merely set Perimeter-Alarm digi output. l The output functionality is fixed... both bells go for the Perimeter-Time when a Perimeter-Alarm l happens. Typical Application Example WIRING
Figure 6. PROGRAMMING AND OPERATION PROGRAMMING Zone Attribute Shock Option
OPERATION Contact Activation Inertia Activation
NO La NO La La La
'Perimeter' Alarm 'Full' Alarm 'Perimeter' Alarm 'Perimeter' Alarm
Ls No Ls Ls No Ls
For programming see Programming Map:
Zones
è
Timers è
'Full' Alarm 'Full' Alarm 'Perimeter' Alarm 'Perimeter' Alarm
Zone attributes Ls for Shock (Zone 1-4) La for Contacts(Zone 1-6) Bell times è perim. bell cutout ON/OFF
WEAPON AGAINST FALSE ALARMS Consider, for example, the situation where the inertia sensor and magnetic contact are wired in series and mounted on a window. When only the zone attributes Ls is added , then the panel will cause a local alarm for inertia sensor activations and a full alarm when the window opens. 14 1791 999
19
Programming Text Literal text is available for programming customized zone and user names. The keypad digits each represent a set of characters. KEYPAD CHARACTER SET ABC
DEF
GHI
JKL
MNO
PQR
STU
VWX
YZ
CURSOR LEFT
CURSOR RIGHT
HOME
The [9] key has a blank space and punctuations (eg. full stop, comma, etc.).
The [0] key has a blank space. SCROLL UP
SCROLL DOWN
HOW TO PROGRAM NAMES Function keys used:
ê key Move to next character. é key Move to previous character. 4
key . Confirm to reprogram current text . Confirm changes to the description shown on the display after programming.
X
key . Restart the programming of a name . Return to previous menu section.
EXAMPLE Reprogram zone 1 01 zone to 01 Door . Enter engineer mode [0][1][2][7][8] l l - display shows 01 zone Jump to zones - zone name [4][4] - display shows 01 _ Confirm to reprogram 4 l Start programming capital letter'D' [2] - display shows 01 2 l Repeat steps till 'D' appears [2]+[2]+.. - display shows 01 D l - display shows 01 D_ Move to next character ê Repeat programming sequence for all characters. l l Confirm new name when the last character shows on the display 4 you can now proceed with the next name ê or return to the previous menu section X .
20
14 1791 999
Returning to Factory Default Without Engineer Lock programmed 1.
Remove all power from the panel. Mains and the battery.
2.
Remove the plug-on link (JP1) on the panel.
3.
Restore the mains power.
4.
The Display will prompt for the Language Default prefered. The display will change every two seconds. UK/IRL Press é1 NL Toets é2 F Taper é3 I Ins. é4
4.
Enter at Keypad 1 the default operators code [0][1][1][2][2].
5.
Enter at Keypad 1 the default engineer's code [0][1][2][7][8].
6.
Replace the plug-on link and reconnect the battery.
With Engineer Lock programmed 1.
Enter Engineer Mode using EXISTING Engineer code at Keypad 1.
2.
Select 'Factory Prorgram Menu' from the miscellaneous section and scroll down to 'Default Settings'. Enter accept ✔ .
NOT E: . When the existing engineer code is unknown, then the control panel must be returned to the factory for reprogramming. . The panel always powers up in Armed condition.
Quick Codes
The use of operator "Quick Codes" can be enabled or disabled by setting "Quick Code" to ON or OFF in the Use Menu. The quick 0 0 0
codes are as follows: 4 Normal Set. 5 Alarm Set (No Buzzer). 7 Alarm Partguard Set.
¯ ¯ ¯
14 1791 999
21
Zone Wiring Options General The main control panel inputs are set up as standard EOL (4K7) zones which are freely programmable to whichever type is required. However, by selecting option 'dual' from the 'zones' menu all main control panel zone inputs can be programmed to give ALARM and TROUBLE indication ON THE SAME ZONE (Fig. 7.). Wiring 1.
The ALARM devices are wired as normal and a 4K7 resistor is fitted in PARALLEL with the complete loop.
2.
The TAMPER switches/devices are wired as normal and a 4K7 resistor is fitted in series with this loop.
Principles of Dual Operation All devices closed ....... loop resistance is 4K7 TAMPER device open loop is open circuit ALARM device open ... loop resistance is 9K4 (ie EOL resistor PLUS parallel resistor)
Example 1 Four wire application for powered motion sensors
Figure 7. Example 2 Multiple sensors wired in a single zone
Figure 8. 22
14 1791 999
Wiring of Aritech Sirens
AS290 / AS390 +
BEACON CONTACTS
4K7
TAMPER LOOP
+
-
SPEAKER
- + - + 1 2 3 4 5 6 7 8 9 10
16 17 3
INPUT POWER (13.0-14.2)
2
SIREN HOLD-OFF VOLTAGE (*)
5
BEACON HOLD-OFF VOLTAGE (*)
7
*) Program Internal (5) and External (7) Bell outputs for positive (+) trigger
TAMPER SWITCH BATTERY
(black) (red) + JUMPERS CUT-OFF TIMER: (minutes)
J2 J1 CUT-OFF TIMER
J1 3’: 5’: 10’: 20’:
J2
✲ = cut
link
✲ ✲
✲ ✲
Figure 9.
14 1791 999
23
Wiring of Outputs
Principle of operation from outputs. Output as shown is 'High'. When programmed for '-' trigger the output will switch to '-' with an alarm condition.
Figure 10.
Wiring to Digital Communicator
Figure 11.
Wiring of Fire Detectors
Figure 12. 24
14 1791 999
List with Short Codes A Armed display on ................................ 61 4 B Bell cut-out time, program ...................24 1 mm Bell delay, program ............................ 24 2 mm Bell option, exit fault ........................... 61 5 Bells cut option, all ............................. 24 3 Buzzer option, line fault ...................... 65 2 Buzzer option, power failure ............... 65 1 C Change of hour backward .................. 27 2 Change of hour forward ...................... 27 1 Chime option, latched ........................ 63 4 Chime, internal bell on ........................ 63 5 D Date, program curren ................. 26 DD MM YY E Engineer code, program ..................... 33 Engineer lock select ........................... 66 2 Engineer reset clear ........................... 64 5 Engineer reset PA .............................. 64 2 Engineer reset tamper ....................... 64 3 Engineer reset (Alarm) ....................... 64 4 Entry time, program ............................ 21 SS Exit time, program .............................. 22 SS F Factory default program select .......... 66 N Final door set ...................................... 61 6 Forced arm select ............................... 61 2 I Input attibute, program ....................... 42 NN Input name, program .......................... 44 NN Input option, A/T dual ......................... 45 Input type, program ............................ 41 NN Input values, program inertia .............. 43 NN Input walk test .................................... 14 NN Inputs, show open .............................. 13 Install new remotes ............................ 52 L Log, clear ............................................ 112 Log, display the .................................. 111
14 1791 999
O Output type, program ..........................51 NN Output, test .......................................... 12 NN P PA at keypad, select ........................... 62 3 PA option, lien fault silent .................... 62 2 PA option, silent .................................. 62 1 Partguard, access to exit on ............... 63 2 Partguard, digi options ........................63 3 Partguard, timed/instant ...................... 63 1 R Rearm options select .......................... 61 3 S Split entry time, program .....................23 SS Shock perimeter select ........................46 T Time, program current ......................... 25 HH MM U User attributes, change ....................... 32 N User code, program ............................. 31 N User walk test, select .......................... 61 1 Key to Abbreviations: HH Enter number of hours mm Enter number of minutes N Enter number of User Code NN Enter number of output/zone SS Enter number of seconds DD Enter number of days YY Enter year MM Enter month
HOW TO WORK WITH SHORT CODES ✔ keys to access Instead of using the programming options, it is possible to directly jump to the menu section required. Immediately after you enter the engineer code, keyin one of the digit sequences as indicated in the Short Code List. -
¯
25
Default Chart
No. 1 2 3 4 5 6
ZONE TYPES Default Required Exit/Entry Alarm Alarm Alarm Alarm Alarm
No. 1 2 3 4 5 6
OUTPUT TYPES Default Required Arm/Disarm Partguard Latch Tamper Int. Bell Ext. Bell
TIMERS Description Default Required Exit time 30 sec. Entry time 30 sec. Split ent. time off Bell delay 0 min. Bell cut off 30 min. OTHER OPTIONS Function Default Required Buzzer for line ON fault Buzzer for powON er failure Latched chime OFF Chime rings Int. OFF bell Current date 01Jan92 Current time 00 00 Engineer lock Engineer reset Code+FTC option Engineer reset OFF Select
Type So Alarm Tamper PA Fire E/E
No. 1 2 3 4 Duress Ud code Eng.
ZONE ATTRIBUTES In Pg Ch 24 Ac l
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
l
x
l
x
x
x
CODES & PRIVILEGES Default Fa Ps Us In Mn Cn x 1122 l l l l Unused x Unused x Unused l Unused x x x x x x Unused x x x x x x x x x x x 1278 x Pu Qs Fs Ps Us Key
l
OTHER OPTIONS cont'd Function Default Required Exit fault of buz- BUZZER zer/bell Final door set OFF Forced arming OFF Inputs alarm or ALARM dual Keyswitch PULSED option KEY PA at keypad OFF PA with line fault BELLS bells or silent PA activations BELLS bells or silent Partguard OFF acces to E/EE Partguard OFF activates digi Partguard INSTANT time/instant Auto rearm NEVER option
x = Not Available (for attributes and privileges charts) 26
l
l
= Default 14 1791 999
Problem Solving
Bells do not ring at bell test.
Alarm zone does not activate system.
1. Check bell fuse. 2. Disconnect bell cable from control panel and connect across battery observing correct polarity. If wiring is correct the bell should ring. Arm system and remove wires from the terminal block. If the system does not activate, disarm and enter Engineer Mode. 1. Check if bell delay time is programmed for [00] ('Timers Menu' at 'Bell Times'). 2. Check if zone is not in soak test ('Zones Menu' at 'Zone Attributes'). 3. If PA zone, check that it is programmed as audible ('Miscellaneous Menu' at 'PA Menu').
Alarm zone name will 1. Enter Engineer mode and open panel. not clear from the 2. Disconnect the alarm zone wires from the terminal block and replace with display when attempta 4K7 resistor. ing to arm the system. 3. Enter 'Show Open Zones' in 'Maintenance Menu' and observe that the zone name in question does not come up on the display. This proves that the panel is functioning correctly. 4. Check the zone wiring to ensure that the circuit is closed and that there are no shorts on the cables. Reconnect the wires back to the panel and retest. Control panel activates 1. during a short power 2. failure. 3. load System returns to factory setting when mains and battery powre are removed.
Check that the battery is connected correctly. Check that the battery fuse is not blown. Ensure that the battery is fully charged and is large enough to carry the of the system.
Check that jumper is on link LK1 on the main control panel.
System activates Before leaving engineer mode check that no PA, FIre, Medical, or Tamper when leaving engineer zones are open. Use 'Show Open Zones' menu to do this. mode. System does not activate when Tamper Check that the internal sounder is connected. opens during day NOTE: the external bell only sounds on tamper fault when the system is (ie when system is armed. If using dual loops, check that the zone type is programmed for disarmed). DUAL (in 'Zones' menu) and that the Tamper devices are wired in series with the EOL resistor.
14 1791 999
27
Problem Solving
Alarm zones cannot be inhibited.
Bell fuse blows when bells are sounding.
Check that the 'In' attribute is set for this zone number ('Zone Attribute' in 'Zones' menu). Check that the user code has 'In' privilege ('Code Privileges' in 'Users' menu). Check that there is no short circuit in bell wiring. Disconnect bell wires from terminal and, observing correct polarity, connect across battery. If bells ring, wiring is correct. The load of the bells is greater than the fuse rating, inserting a higher value fuse may damage the panel. Spread the load of the bells across the bell outputs or fit a relay and use the auxiliary power output to provide some of the current.
PA is activating when Ensure that the operator is not entering the duress code when switching off alarm is switched off. the system. 'No panel data' shows This happens when the keypad is not receiving correct data from the panel. on the display. Check wiring to the keypad, especially for swapped wires. Check that the address is correctly set on the keypad.
28
14 1791 999
Technical Specification
Power Input
230 V AC ±10%, 50Hz, 14.5 VA
Current Consumption
CS350 CD3008
Output Voltage
13.8 V DC ±5%
Quiescent: 30mA Quiescent: 30mA
Alarm: 50mA Alarm: 50mA
Normal Surge 800mA 2A 800mA 2A
Signalling Output
Internal bell External bell
Programmable Outputs
50 mA each
Loop characteristics
6 inputs, configurable as double-pole loops using 4K7 resistors. Response time: 300 ms.
Battery Backup
12 V lead acid rechargeable battery (not supplied) Float charging method at 13.8 V ±5%, 800mA max. charging current. 6.5 Ah recommmended
Auxiliary Power Output
13.8 V DC fused at 800mA.
Note: if the combined current is greater than 800mA for the above devices, the load will be shared by the standby battery.
14 1791 999
29
CS350 WIRING DIAGRAM Y
S O
NI
.
G .L
R
O.
T
E
T C T A F
. C . N
. C . N
E S
. C . N
. C . N
. C . N
. C . N
D C B A 4
+ 3 2 1
-
✆
+ + +
+ -
Figure 13. 30
14 1791 999
14 1791 999
31
