Artigo da última atualização do APGDescripción completa
Full description
Full description
Full description
Descripción completa
case reportFull description
Deskripsi lengkap
case reportDeskripsi lengkap
APG 1
Accessing Personal Genius Training manual by the neurosemantics societyDescrição completa
Accessing Personal Genius Training manual by the neurosemantics society
Accessing Personal Genius Training manual by the neurosemantics society
Full description
bFull description
radarFull description
for 5eDescrição completa
3G OSS Commands EricssonDescripción completa
Ericsson CommandsFull description
Unix komutları
Full description
APG COMMANDS // AP File Processing Fault aploc; hostname cdhdsls afpls -ls NYMSC019 OSSMETRICA | findstr FAILED afpfti -f NYMSC019 OSSMETRICA afpls -ls NYMSC019 OSSMETRICA | findstr FAILED alist exit // AP Proccess Reinitiated, Restarted Aploc; Cluster Res ! Verify all resources are ONLINE, otherwise contact Tier 2 ! Alist ! Pay attention to the Alarm Identifier ! ! Replace after acease command ! Acease 6023:0 Exit * IF alarm repeatedly comes back open a ticket w/Tier 2 and call out.
// Security alarms in APG aploc; ! Inits AP Local mode ! alist net user ! Lists all users on system, email, call user to verify it was them logging in ! acease xxxx:x ! Ceases alarm ! exit ! Exits local mode !
// APG check node status ! Logs in local mode, checks AP state, verifies node your in, checks all resources are ONLINE, and prints alarm list ! Aploc; Prcstate Hostname Cluster Res Alist
CHECK APG STATUS
list ! Aploc; Prcstate Hostname Cluster Res Alist
C:\>cluster node
! Listing status for all available nodes:
C:\>cluster group
! Listing status for all available resource groups:
1. Connect APG 2. Make FMS_CPF_server offline -cluster res FMS_CPF_server/off 3. After making it off, check that the service is offline -cluster res -N:B: Notice that other services served by this server also go offline. FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr
Disk Group Disk Group
GWR1AP0A GWR1AP0A
Disk Group
GWR1AP0A
Offline Offline Offline
CPS_BUAP_loader
Disk Group
GWR1AP0A
Offline
CPS_BUAP_filemgr
Disk Group
GWR1AP0A
Offline
CPS_BUFTPD
Disk Group
GWR1AP0A
Offline
4. Make the service online again -cluster res FMS_CPF_server/on
5. Check that the server is back online but the services under it are still offline.
-cluster res FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr
Disk Group Disk Group Disk Group
GWR1AP0A GWR1AP0A
Online Offline
GWR1AP0A
Offline
CPS_BUAP_loader
Disk Group
GWR1AP0A
Offline
CPS_BUAP_filemgr
Disk Group
GWR1AP0A
Offline
CPS_BUFTPD
Disk Group
GWR1AP0A
Offline
6. Make the services running on this server online one b y one -cluster res CPS_BUSRV/on -cluster res CPS_BUAP_parmgr/on -cluster res CPS_BUAP_loader/on -cluster res CPS_BUAP_filemgr/on -cluster res CPS_BUFTPD/on 7. Make sure the server and its services FMS_CPF_server CPS_BUSRV CPS_BUAP_parmgr
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Ap syst analysis ap-1 node-a (less space i n memory)
cluster res mcs_adh_adm /fail cluster res fms_cpf_server /fail
Clear any AP larms appearing after this stage
cluster res mcs_adh_adm /online cluster res fms_cpf_server /online
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! APG EXTERNAL ALARM RECEIVER FAULT
1ST check for physical alarm Allip:alcat=power in the switch If no alarm, do the following.
TAKE OFF THE RESOURCES OFF MCS_ALEC_ADM MCS_ALDM_ADM
cluster res MCS_ALEC_ADM /off cluster res MCS_ALDM_ADM /off
Then put them on again
cluster res MCS_ALEC_ADM /on cluster res MCS_ALDM_ADM /on
The alarm should clear. If it does not clear, then the SE is required to visit the switch and check physically. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Ceasing hanging APG alarms acease [space] [-o] [specificProblem:indexNumber]
C:\>acease -o 8799:0 Alarm ceased. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! TTFILE TRANSFER FAILURE Log in to APG2 (e.g. GSR4_1) C:\>cdhver INITFTP1
Verify the primary Destination/Dest should be OK
DESTINATION INITFTP1
STATUS OK
NOTIFICATION
-
C:\>afpls - ls
Check the failed files
C:\>afpfti -f ttfile00
Retransfer failted files
How to print commands and alarms logged into APG
alogfind -a 1300 20081201 -b 1700 -g 20081214 -t "alp" to check for alarm printouts
alogfind -a 1300 20081201 -b 1700 -g 20081214 -s "NSSTP" to check for a particular command !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ANY SYB* Command giving Function busy
1.
Cluster RES Check the MCS_ADH_ADM resource Check FMS_CPF_server resource Check CPS_BUSRV resource
Take these resources offline
Cluster res MCS_ADH_ADM off Cluster res FMS_CPF_server off Cluster res CPS_BUSRV off
Put the resources back online
Cluster res MCS_ADH_ADM on Cluster res FMS_CPF_server on Cluster res CPS_BUSRV on
Check again the SYB* Command. If it still gives you function busy, go to 2 below
2.
*** Connected to GSR8 ***
SAE
BLOCK
800 APFMI
CNTRTYP NI MANUAL
NIU 64
NIE
NIR
2
END
SAE
BLOCK
800 APFMI
CNTRTYP NI MANUAL
NIU 100
NIE 2
END
After increasing the SAE, Command SYB* No longer shows busy
