7 Segment Display

7-Segment Display Interfacing and Programming 5.1

Introduction

Till now you have learn what is an embedded system, basic memory architecture of a microcontroller, how to implement assembly language and use of some softwares like pinnacle 52, keil-C and flash magic; we also have come across how to interface LEDs from a microcontroller and how to generate different pattern through it. now its time to move forward and learn one more step ahead towards the completion of our 6-weak training. so here today we will learn about 7-Segment display; How to interface and program it; and some of the applications of it. 5.2

7-Segment Display

A 7-Segment display is a useful electronic component use to produce numeric, alphabetic and some non-alphabetic symbols using a specific arrangement of LEDs as shown in figure here. A 7-Segment display has 10-Pins representing each a, b, c, b, e, f, g and h LEDs respectively along with two extra pins for GND and VSS. following shown an original 7-Segment display device along with its pin diagram. LED h is also denoted by symbol dp.

As we have studied in LED interfacing a 7-segment display is also interfaced in same way as it is also made of LEDs. So we can interface LEDs in three ways bu here difference is that 7-Segment displays comes in two types by manufacturers i.e. "Common Anode" and "Common Cathode"; the logics are shown in figure below.

and

and thus which logic is o implement is on the bases of these specifications provided by manufacturer. interfacing in our case has been shown below. 5.3

7-Segment Display Interfacing

We interface 7-Segment display with port zero of microcontroller; and to do so we connect P0.0 to P0.7 to Pin a to dp (h) of 7-Segment display respectively; and connect Vss terminal of display to 5V Power supply and GND pin to ground. the configuration is shown in figure below.

5.4

Cascading seven segment display

Here we have a question in mind that if we want to interface more then one 7-Segment display with microcontroller what we will do??? as we are using one port for one 7-segment display if we use all the four ports for four 7-Segment display??? isn't it less efficient??? The answer of all these questions are hidden under this topic "CASCADING" cascading refers to connecting similar or non-similar component from the same connections with a reference of enabling and disabling each components according to specification. For cascading four 7-Segment display we use the following schem where all the a to f (dp) pins of 7-segment display are connected paralleled to the port zero of microcontroller along with common ground and Vss pin of all the four 7-segments are use for enabling and disabling them so are connected to port two of microcontroller along with NOT Gate in order to " " and thus clearing or sending "0" on pins of port two cause enabling the display and signal "1" cause disabling it.

5.5

7-Segment Display Programming

Programming a 7-Segment display is so easy as to program a LED array but here pattern should be generate in a manner so as it appears as a meaningful character and with cascaded mode we also need to send "clear" (0) or "set bit" (1) signal on respected pins of port two in order to enable or disable respected 7Segment display. The signals on Port zero which can generate meaningful characters on 7-Segment display are listed in table below.

Example Lets write a program to show character "3" on 7-Segment display.



Showing character "3" on 7-Segment display ;**************************************** ;** Showing character "3" on 7-Segment display ** ;**************************************** org 0000h

;Origin

main: clr sbit sbit sbit

;Main subroutine P2.0 P2.1 P2.2 P2.3

mov P0,11110010b

;Enabling Display-1 ;Disabling Display-2 ;Disabling Display-3 ;Disabling Display-4 ;Sending LED pattern of character "3" at port

zero jmp $ end

;End

OUTPUT

5.6

Generating counting from 0 to 9

0 to 9 Counter

;************************************* ;************ 0 to 9 Counter ************* ;************************************* org 0000h

;Start

main: clr sbit sbit sbit

P2.0 P2.1 P2.2 P2.3

;Main Subroutine ;Enabling Display-1 ;Disabling Display-2 ;Disabling Display-3 ;Disabling Display-4

mov P0,#0FCh call delay zero

mov P0,#60h call delay

mov P0,#0DAh character "2" to Port zero call delay

;Sending character "0" to Port zero ;Calling Delay Function ;Sending pattern of character "1" to Port ;Calling Delay Function ;Sending pattern of ;Calling Delay Function

mov P0,#0F2h ;Sending pattern of character "3" to Port zero call delay ;Calling Delay Function mov P0,#66h ;Sending pattern of character "4" to Port zero call delay ;Calling Delay Function mov P0,#0B6h character "5" to Port zero call delay

;Sending pattern of

mov P0,#0BEh character "6" to Port zero call delay

;Sending pattern of

;Calling Delay Function


mov P0,#0E0h ;Sending pattern of character "7" to Port zero call delay ;Calling Delay Function mov P0,#0FEh ;Sending pattern of character "8" to Port zero call delay ;Calling Delay Function mov P0,#0F6h

;Sending pattern of

character "9" to Port zero call delay


jmp main

;Infinite Loop

delay:

;Delay Function

mov 40h,#0FFh

;Move FFh to memory location with address

40h

L1: ;Label "L1" mov 41h,#99h ;Move 99h to memory 41h djnz 41h,$ ;Jump here till 41h becomes zero djnz 40h,L1 ;Jump to "L1" till 40h becomes zero ret ;return end

;End

OUTPUT

5.7

Generating counting from 0 to 9 [using array]

0 to 9 Counter using Array ;************************************* ;******** 0 to 9 Counter using Array********* ;************************************* org 0000h main: clr sbit sbit sbit

P2.0 P2.1 P2.2 P2.3

mov a,#00h Up:

;Enabling Display-1 ;Disabling Display-2 ;Disabling Display-3 ;Disabling Display-4

mov 30h,a mov dptr,#arr movc a,@a+dptr mov P0,a call delay mov a, 30h inc a jmp Up jmp main arr: db db db db db db db db db db

11111100b 01100000b 11011010b 11110010b 01100110b 10110110b 10111110b 11100000b 11111110b 11110110b

delay: mov 40h,#0FFh L1: mov 41h,#99h djnz 41h,$ djnz 40h,L1 ret end

OUTPUT

5.8

Generating two digit numbers

Two digit number ;************************************* ;*********** Two digit number ************ ;************************************* org 0000h main: clr sbit sbit sbit

P2.0 P2.1 P2.2 P2.3

mov P0,#01100000b call delay clr sbit sbit sbit

P2.1 P2.0 P2.2 P2.3

mov P0,#11011010b call delay jmp main delay: mov 40h,#50h L1: mov 41h,#99h djnz 41h,$ djnz 40h,L1 ret end

OUTPUT

5.9

Generating two four bit numbers alternatively

Alternating two four digit numbers ;************************************ ;***** Alternating two four digit numbers ***** ;************************************ org 0000h main: mov 30h,#0FFh UP1: clr sbit sbit sbit

P2.0 P2.1 P2.2 P2.3


P2.1 P2.0 P2.2 P2.3


P2.2 P2.1 P2.0 P2.3


P2.3 P2.1 P2.2 P2.0

mov P0,#01100110b call delay

djnz 30h,UP1 jmp $ mov 30h,#0FFh UP2: clr sbit sbit sbit

P2.0 P2.1 P2.2 P2.3


P2.1 P2.0 P2.2 P2.3


P2.2 P2.1 P2.0 P2.3


P2.3 P2.1 P2.2 P2.0

mov P0,#11111110b call delay djnz 30h,UP2 jmp $ jmp main delay: mov 40h,#30h L1: mov 41h,#99h djnz 41h,$

ret

djnz 40h,L1

end

OUTPUT

Program to implement 7-Segment Display with 8051 microcontroller By ankur bhardwaj embedded What is 7 Segment Display?

7 Segment Display is an array of 8 LEDs connected or arranged in a special pattern together to form or display the digits from 0-9 and Dot functions also. The 7segments are arranged as a rectangle of two vertical segments on each side with one horizontal segment on the top, middle, and bottom. Additionally, the seventh segment bisects the rectangle horizontally. There are also fourteen-segment displays and sixteen-segment displays. It is composed of 7 LEDs assigning specific alphabet to each and 1 LED acts as a dot in the display. Every LED is assigned a name from 'a' to 'h' and is identified by its name. Seven LEDs 'a' to 'g' are used to display the numerals while eighth LED 'h' is used to display the dot/decimal. Concept: A 7-segment is generally available in ten pin package. While eight pins correspond to the eight LEDs, the remaining two pins (at middle) are common and internally shorted. These segments come in two configurations, namely, Common cathode (CC) and Common anode (CA). In CC configuration, the negative terminals of all LEDs are connected to the common pins. The common is connected to ground and a particular LED glows when its corresponding pin is given high. In CA arrangement, the common pin is given a high logic and the LED pins are given low to display a number.

Common Cathode and Common Anode Configuration

Configuration:

This below table specify how 7-segment will display the digit when one of the LED is OFF or ON accordingly.

Packaging of 7-Segment Display:

Seven-segment displays can be packaged in a number of ways. Three typical packages are shown above.

1. On the left we see three small digits in a single 12-pin DIP package. The individual digits are very small, so a clear plastic bubble is molded over each digit to act as a magnifying lens.

The sides of the end bubbles are flattened so that additional packages of this type can be placed end-to-end to create a display of as many digits as may be needed.

2. The second package is essentially a 14-pin DIP designed to be installed vertically.

Note that for this particular device, the decimal point is on the left. This is not true of all sevensegment displays in this type of package.

One limitation of the DIP package is that it cannot support larger digits. To get larger displays for easy reading at a distance, it is necessary to change the package size and shape.

3. The package on the right above is larger than the other two, and thus can display a digit that is significantly larger than will fit on a standard DIP footprint. Even larger displays are also available; some digital clocks sport digits that are two to five inches tall.

Interfacing with 8051

The circuit diagram shown above is of an AT89S51 microcontroller based 0 to 9 counter which has a 7 segment LED display interfaced to it in order to display the count. This simple circuit illustrates two things. How to setup simple 0 to 9 up counter using 8051 and more importantly how to interface a seven segment LED display to 8051 in order to display a particular result. The common cathode seven segment display D1 is connected to the Port 1 of the microcontroller (AT89S51) as shown in the circuit diagram. R3 to R10 are current limiting resistors. S3 is the reset switch and R2,C3 forms a debouncing circuitry. C1, C2 and X1 are related to the clock circuit. The software part of the project has to do the following tasks.   

Form a 0 to 9 counter with a predetermined delay (around 1/2 second here). Convert the current count into digit drive pattern. Put the current digit drive pattern into a port for displaying.

    

B ui ld awe b site

We b p age de si gn

P cb Layou ts

Th i sVide o

P ro je cts

Code #include "REG52.h" #define SEG P2 sbit C1=P0^0; // BIT DEFINATION long int i; void main() { C1=C2=C3=1; while(1) { SEG=0x06; C1=0; for(i=0;i<256;i++); C1=1; SEG=0x5B; C1=0; for(i=0;i<256;i++); C1=1; SEG=0x4F; C1=0; for(i=0;i<256;i++); C1=1; } }

Explanation of Code: - This code implements single seven segment LED display with common cathode to 8051 microcontroller. Connect common cathode pin to any port pin of microcontroller as we define it C1

in code. Now, ON/OFF that pin to view the character on display. Mark the values accordingly to extract the HEX value and pass it to the port to seven segment to display character

Seven segment based digital clock with time set option using 8051 microcontroller (AT89C51) MC009       

Summary Description Circuit Diagram Video Code Code2 Components

This digital clock not only displays time (on four seven segment displays) but also provides the user an option to set the time. For this the user has to first press the reset switch after which he/she can select and set a particular digit by incrementing its value. To run the clock with the set time, the user needs to press the start button. The seven segment and switches are interfaced with microcontroller AT89C51.



This idea to provide option for setting time can be implemented in conjunction with the digital clock circuit. The control options for time setting are provided by means of tactile switches which are made active low. This circuit uses four such switches for following functions.

Switch 1 (S1) :

Reset

(to initiate the time set option)

Switch 2 (S2) :

Select

(to select the segment where value is to be changed)

Switch 3 (S3) :

Increment

(to increase the value at selected segment)

Switch 4 (S4) :

Start

(to start the clock with the set time options)

As soon as S1 is pressed, the running clock stops and it goes into the reset mode where the first segment is activated. The segment to be set can be selected in cyclic order each time S2 is pressed. After selecting the desired segment, its value can be changed by using S 3. Once the digits and hence the time is set, S 4 is pressed to start the clock again. The seven segments are interfaced to port P2 of the microcontroller through its data pins (a h). The enable pins are connected to pins 1-4 of port P1 (P1^0 – P1^3). The switches S1-S4 are connected as following to provide ground to the corresponding pins of port P 1: S1

:

P1^4

S2

:

P1^5

S3

:

P1^6

S4

:

P1^7



// Program to make a clock with time setting functionality. #include sbit dig_ctrl_4=P1^0; //Declare the control pins of the seven segment sbit dig_ctrl_3=P1^1; sbit dig_ctrl_2=P1^2; sbit dig_ctrl_1=P1^3; sbit reset=P1^4; // Reset pin to reset the clock. sbit start=P1^7; //Start pin to start the clock after the time is set. sbit incr=P1^6; //Increment pin to increase the digits during time setting. sbit set=P1^5; // Set pin to set the time. int sel_seg_to_incr=0; int ret_seg_to_incre=0; int recnt_incr_seg; unsigned char dig_disp=0; int min2=0; int min1=0; int sec2=0; int sec1=0; char dig_val[10]={0x40,0xF9,0x24,0x30,0x19,0x12,0x02,0xF8,0x00,0x10}; // to store values corresponding to digits 0 to 9 void delay(int a) //Function to provide a time delay of approx. 1 second using Timer1. { int i; for(i=0;i
dig_ctrl_3=1; dig_ctrl_2=0; dig_ctrl_1=0; recnt_incr_seg=2; ret_seg_to_incre=2; P2=dig_val[min1]; delay(20); } case 3: if(set==0) //Select the sec 2 digit { dig_ctrl_4=0; dig_ctrl_3=0; dig_ctrl_2=1; dig_ctrl_1=0; recnt_incr_seg=3; ret_seg_to_incre=3; P2=dig_val[sec2]; delay(20); } case 4: if(set==0) //Select the sec1 digit { recnt_incr_seg=1; dig_ctrl_4=0; dig_ctrl_3=0; dig_ctrl_2=0; dig_ctrl_1=1; ret_seg_to_incre=4; P2=dig_val[sec1]; delay(20); recnt_incr_seg=1; } } } return(ret_seg_to_incre); } void increase(int a) //Function to set the minute or seconds digit { while(incr==0) { switch(a) { case 1: // To set the min2 digit. P2=dig_val[min2]; //Display the value of min2 delay(15); min2++; if(min2==6) min2=0; P2=dig_val[min2]; delay(5); break; case 2: //To set the min1 digit. P2=dig_val[min1]; delay(15); min1++; if(min1==10)

min1=0; P2=dig_val[min1]; delay(5); break; case 3: // To set the sec2 digit. P2=dig_val[sec2]; delay(15); sec2++; if(sec2==6) sec2=0; P2=dig_val[sec2]; delay(5); break; case 4: //To set the sec1 digit. P2=dig_val[sec1]; delay(15); sec1++; if(sec1==10) sec1=0; P2=dig_val[sec1]; delay(5); break; } } } void resetfn() // This function brings the clock to reset or set mode. { IE=0x80; //Disable timer0 interrupt to stop the display of the clock sel_seg_to_incr=1; recnt_incr_seg=1; dig_ctrl_4=1; dig_ctrl_3=0; dig_ctrl_2=0; dig_ctrl_1=0; P2=dig_val[min2]; delay(5); while(1) { if(start==0) //check if start pin is pressed { TMOD=0x11; //reset the timer0 TL0=0xf6; TH0=0xFf; IE=0x82; //enabling again the timer0 interrupt to start displaying of the clock TR0=1; break; // break loop and return to main program } if(set==0) //if set pin is pressed call set function sel_seg_to_incr=setfn(); if(incr==0) // if incr pin is pressed call incr function increase(sel_seg_to_incr); } } void display() interrupt 1 // function to display the values on seven segmnet. For more details refer seven segment multiplexing.

{ TL0=0x36; //reloading timer0 TH0=0xf6; P2=0xFF; dig_ctrl_1 = dig_ctrl_3 = dig_ctrl_2 = dig_ctrl_4 = 0; dig_disp++; dig_disp=dig_disp%4; switch(dig_disp) { case 0: P2=dig_val[sec1]; dig_ctrl_1 = 1; break; case 1: P2= dig_val[sec2]; dig_ctrl_2 = 1; break; case 2: P2= dig_val[min1]; dig_ctrl_3 = 1; break; case 3: P2= dig_val[min2]; dig_ctrl_4 = 1; break; } } void main() //main function the programs begins from here { set=1; //delaring set, reset, start and incr as input pins reset=1; start=1; incr=1; TMOD=0x11; //enabling timer0 TL0=0xf6; //loading timer0 TH0=0xFf; IE=0x82; //initialize timer0 interrupt TR0=1; //triggering timer0 while(1) //forward counting of clock { while(min2<6) { while(min1<10) { while(sec2<6) { while(sec1<10) { if(reset==0) resetfn(); delay(20); sec1++; } sec1=0; sec2++; } sec1=0;

sec2=0; min1++; } sec1=0; sec2=0; min1=0; min2++; } min2=0; } }

Decimal Counter Using Two 7-segment displays and an 8051. Introduction The purpose of this lab is to implement a decimal counter which counts from 0 to 99. You will have to write a C program for the 80X51 micro-controller. You will then compile your C program using C51 compiler and burn it unto an 8051 stand alone chip. You will also have to do some wiring in this lab. The 8051 chip requires some connections to function properly, and the 7-segment displays need to be wired to the 8051. Schematics are provided below. Before you can write your C program, you have to understand how the 7-segment displays work. The 7-segment displays used in the lab are the LSD5061-11 display. Each of the segment corresponds to a pin (see below for the pinout). In order to light up a particular segment, it's pin must be set to 0V. Since these pins are connected to the 8051, we simply set the corresponding pin on the 8051 to '0'. To turn a segment off, the pin must be set to 5V. This is done by setting the corresponding pin on the 8051 to "1". Instead of going through each of the seven pins and setting them to '1' or '0' each time we want to display a number, we will use a lookup table unsigned char LookupTable[11] = { }. The location of the entry in the table corresponds to the correct pin settings to display that number. Simply, LookupTable[0] returns the correct pin settings to display a "0" on the 7-segment display. Now we have to figure out the correct entries into the table. We know that in order to display a "0" on the 7-segment display we need to turn on segments s1, s2, s3, s4, s5, and s6. To turn a segment on, we set the corresponding pin to "0". Segment s7 will need to be turned off. To turn off this segment we set the corresponding pin to "1". Therefore, the pins will need to be assigned the following values: P2^0 = 0; P2^1 = 0; P2^2 = 0; P2^3 = 0; P2^4 = 0; P2^5 = 0; P2^6 = 0; P2^7 = 1; P2^8 = 1; //don't care what this value is since it is not used We set it to 1 because the 8051 pins are by default 1 The bit pattern desired is 1100 0000 (remeber that pin 8 is the highest bit). We then convert the values into hexadecimal 1100 -> C and 0000 -> 0. We fill in the table with this value 0xC0. The "0x" is needed before the actual value to indicate to the compiler that it is a hexadecimal value. Now when we call LookupTable[0] it will return the proper configuration to display a "0" on the 7-segment display. You will need to fill in the rest of the values (1-9). LookupTable[10] will indicate an error has occured, at this location segment s7 will be on,

the remaining segments will be off. (If you want, you can also look at the 7-segment display datasheet.)

Segment number

LSD5061-11 Pin number

8051 pin number (One's place display)

8051 pin number (Ten's place display)

s1

pin 1

P2.0

P3.0

s2

pin 2

P2.1

P3.1

s3 s4

pin 4 pin 6

P2.2 P2.3

P3.2 P3.3

s5

pin 7

P3.4

P2.4

s6

pin 9

P2.5

P3.5

s7

pin 10

P2.6

P3.6

Assignment In this lab :    

You will implement a decimal counter using the C programming language for the 8051 micro-controller and display the count (0 to 99) on two 7-segment displays. You will then burn your program on the 8051. Make necessary connections the 8051 chip and the two 7-segment displays. Verify the correctness of your circuit.

Apparatus Required 1. 2. 3. 4. 5.

330 resistors (4) 7-segment display (2) 5V power supply 8051 chip 12MHz crystal (clock)

Schematic

Program #pragma SMALL DB #include /* P0, P1, P2 and P3 are predefined port names and are bit addressable */ unsigned char SetDisplay(unsigned char value){ unsigned char LookupTable[11] = { 0xC0, ... }; /* check to see if "value" is in bounds,

if not return an error */ if( ) { /* return appropriate value */; } else { /* return error value */; } } /* Delay function */ void delay() { int i, j; for(i=0; i<1000; i++) for(j=0; j<100; j++) i = i + 0; } void main(void){ unsigned char count = 0;

/* value held in one's place */

while(1) { /* determine and display the one's place */ /* determine and dipslay the ten's place */ /* update the counter (remember to keep it within bounds)*/ delay(); } }

Procedure Hardware 1. Wire up the circuit as shown in the schematic. 2. Pinouts are also available:  8051  7-segment display Software 1. Map your network drive to P:\\Peart\cs122 2. Run the batch file cs122.bat 3. Create a directory for your program on the C: drive (i.e. C:\Temp\counter)

4. Using a text editor (i.e. notepad, etc...) type in the program provided and add any necessary code to your program. 5. Compile your program to generate object file count.obj 6.

c51 count.c

7. Link the object file to create your executable file count.omf. bl51 count.obj to count.omf

8. Create a hex file, count.hex, used to burn your program unto the 8051 chip 9.

oh51 count.omf

10. Copy your hex file to a floppy 11.

copy count.hex A:\count.hex

Burning A Chip - Programmer: MP-51 1. 2. 3. 4. 5. 6.

Place the chip to be programmed on the slot making sure that the correct side is up Use the arrow keys on the keyboard to choose options Choose Type -> 51Controller -> PC89C52U Choose File -> Load and enter the pathname of your hex file (i.e. A:\counter.hex) Choose Command -> Program -> DeviceMemory -> Program Device Memory The chip will be programmed. Remove it from the chip from the socket. It is now ready to be plugged into your board.

Testing Your Program 1. Make sure that your chip has the power and ground connections as specified by the schematic. 2. Connect pin 9 to ground. 3. Supply power to your board (make sure the power supply is set to 5V, if it is higher you will damage the 8051 chip.) 4. Pulse pin 9 to power then return it to ground. 5. Your program should now be running. Test to see if it is working correctly. 6. If your program is not working as desired you will have to modfiy your program, then compile and download unto the chip again.

7 Segment Display

Recommend Documents