2007 NEMA & IEC Motors Selection Guide

2007 AC Motors Selection and Pricing Guide

Catalog D81.2, U.S./Canada

2007 AC NEMA & IEC Motors Selection and Pricing Guide

low voltage Siemens Energy & Automation, Inc. 3333 Old Milton Parkway Alpharetta, GA 30005

Siemens Canada, Ltd. 2185 Derry Road West Mississauga, ON L5N7A6

1-800-964-4114 [email protected]

Phone: 905-819-5800 Customer Interaction Centre: 888-303-3353

www.sea.siemens.com/motors

www.siemens.ca

NEMA & IEC

©2006 Siemens Energy & Automation, Inc. Siemens is a registered trademark of Siemens AG. All products mentioned may be trademarks or registered trademarks of their respective companies. Specifications subject to change without notice.

NMSP-00370-1106 5M1106BP

Printed in USA

Table of Contents High quality and the highest efficiency.

NEMA MOTORS Introduction

Table of Contents NEMA Motor Features at a Glance Wide Selection of Motors Cancellation Charges & Change Notices

1-1–1-3 1-4–1-9 1-10 1-11

HIGH | Efficient Motors General Purpose – ODP

DP10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1–2-3

General Purpose – TEFC

GP10A (Cast Aluminum Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 GP10A – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5–2-6 GP10A – C-Face, Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . .2-6–2-7 GP10A – C-Face, Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7–2-8 GP10 (Cast Iron Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9 GP10 – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10–2-11 GP10 – C-Face, Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . .2-11–2-12 GP10 – C-Face, Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12–2-13 RGZP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14 RGZP – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15–2-17 RGZP – C-Face, Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . .2-17–2-18 RGZP – C-Face, Vertical with Drip Cover, Footless . . . . . . . . . . . . . . . . . . . . . . .2-18 Severe Duty – TEFC SD10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19 SD10 - Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-20–2-21 SD10 - C-Face, Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21–2-22 RGZPSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-23 RGZPSD – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24–2-25 RGZESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-26 RGZESD – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-27–2-31 RGZESD – C-Face, Vertical with Drip Cover, Footless . . . . . . . . . . . . . . . .2-31–2-33 Severe Duty – Multi-Speed RGZESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-34 RGZESD – 1 Winding Variable Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-35 RGZESD – 1 Winding Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-36 RGZESD – 2 Winding Variable Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-37 RGZESD – 2 Winding Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-38 Hazardous Duty RGZZESD – (I,D,II,F&G,1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-39–2-43 RGZZVESD – C-Face, Vertical with Drip Cover, Footless . . . . . . . . . . . . . . . . . .2-44 RGZZESD – (I,C&D,1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-45–2-47 Automotive Duty RGZEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48–2-49 Brake RGZESDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-50–2-52 NEMA Design C RGZTESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-53–2-54 P-Base – Vertical Solid Shaft – Normal Thrust Severe Duty – TEFC RGZVESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-55–2-57 Hazardous Duty RGZZVESD (I,D,1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-58–2-60 P-Base – Vertical Solid Shaft – Medium Thrust Severe Duty – TEFC RGZVMTESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-61–2-63 Hazardous Duty RGZZVMTESD (I,D,1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-64–2-66 P-Base – Vertical Solid Shaft – In-Line Thrust Severe Duty – TEFC RGZVILESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-67–2-69 Hazardous Duty RGZZVILESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-70–2-72 P-Base – Vertical Hollow Shaft – High Thrust Severe Duty – TEFC HSRGZVESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-73–2-74

PREMIUM | Efficient Motors (NEMA Premium®) General Purpose - TEFC

That’s what Siemens delivers to the motors industry. A global technology leader, Siemens is committed to providing cutting-edge innovations and the finest motors possible for the future and beyond.

Severe Duty – TEFC

GP100A (Cast Aluminum Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 GP100A – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2–3-3 GP100A – C-Face, Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . .3-3–3-4 GP100A – C-Face , Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4–3-5 GP100 (Cast Iron Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6 GP100 – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7–3-8 GP100 – C-Face, Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . .3-8–3-9 GP100 – C-Face, Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9–3-10 SD100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

2007 Low Voltage AC Motors Selection and Pricing Guide

1-1

Table of Contents

Table of Contents

SD100 – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12 SD100 – C-Face, Horizontal, Footless . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13–3-14 RGZEESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15 RGZEESD – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16–3-20 RGZEESD – C-Face, Vertical with Drip Cover, Footless . . . . . . . . . . . . . . .3-20–3-22 Severe Duty / IEEE841 – TEFC

SD100 IEEE841 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23 SD100 IEEE841 – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . .3-24–3-25 RGZEESDX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-26 RGZEESDX – Horizontal, Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . .3-27–3-31

INVERTER | Duty Motors

IEC Metric Motors

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1–4-2 Severe Duty - TEFC/TEBC RGZESDI – Variable Torque / Costant Torque . . . . . . . . . . . . . . . . . . . . . . . .4-3–4-7 RGZESDI – 10:1 Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8–4-10 RGZESDI – 1000:1 Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11–4-13 Hazardous Duty

P-Base – Vertical Solid Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15 P-Base – Vertical Hollow Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16 TEFC – NEMA Premium Efficient (RGZEESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17–8-18 TEFC – IEEE 841 – NEMA Premium Efficient (RGZEESDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-19–8-20 TEFC – NEMA Premium Efficient & IEEE 841 – C-Face with and without Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-21–8-22 TEFC – NEMA Premium Efficient & IEEE 841 – D-Flange with and without Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-23–8-24 TEFC – Inverter Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-25 TEFC – Inverter Duty – TEBC with or without Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-26 TEFC – Inverter Duty – with Lake Shore SL56 & Internally Mounted Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-27 TEFC – Inverter Duty – with Dynapar HS35 Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-28 TEFC – Inverter Duty – with Lake Shore 8500 Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-29 TEFC – Recommended Sheave Diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-30

RGZZESDI (I,D,II,F&G,1) – 6:1 VT or 6:1 CT . . . . . . . . . . . . . . . . . . . . . . .4-14–4-16 RGZZESDI (I,C&D,II,F&G,1) – 6:1 VT or 6:1 CT

. . . . . . . . . . . . . . . . . . . .4-17–4-19

Introduction IEC Motor Features at a Glance General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1

Improved | Efficient Motors EFF2 Aluminum Frame

1LA7 B3 Foot Mounted B5 Flange, Footless B14 Flange, Footless

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . .10-2–10-5 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . .10-6–10-7 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . .10-8–10-9

EFF2 Cast Iron Frame

1LA6 B3 Foot Mounted

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-10 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . . . . . .10-11

EFF2 Explosion Proof

1MJ6 B3 Foot Mounted IMJ7 B3 Foot Mounted

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12 50 Hz & 60 Hz . . . . . . . . . . . . . . . .10-13–10-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . . . . . .10-15

EFF1 Aluminum Frame

1LA9 B3 Foot Mounted B5 Flange, Footless B14 Flange, Footless

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-16 50 Hz & 60 Hz . . . . . . . . . . . . . . . .10-17–10-18 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . . . . . .10-19 50 Hz & 60 Hz . . . . . . . . . . . . . . . . . . . . . .10-20

EFF1 Cast Iron Frame

1LG6 B3 Foot Mounted

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-21 50 Hz & 60 Hz . . . . . . . . . . . . . . . .10-22–10-23

Lead Time Stock Motor Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1 Custom Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Modifications | Accessories Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1 Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2–6-17

Typical Performance Data Technical Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1 General Purpose – ODP – High Efficient (DP10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2–7-3 General Purpose & Severe Duty TEFC – High Efficient (GP10A/GP10/SD10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4 General Purpose & Severe Duty – TEFC – High Efficient (RGZP/RGZPSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5–7-6 Severe & Hazardous Duty – TEFC – High Efficient (RGZESD/RGZZESD/RGZESDB) . . . . . . . . . . . . . . . . . . . . . . . . .7-7–7-8 Severe Duty – TEFC – Multi-Speed – 1 Winding Variable Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9 Automotive Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-10 NEMA Design C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11 Severe & Hazardous Duty – P-Base – Vertical Solid Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-12–7-13 Severe Duty – P-Base – Vertical Hollow Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-14 General Purpose & Severe Duty – TEFC – NEMA Premium Efficient (GP100A/GP100/SD10) . . . . . . . . . . . . . . . . . . .7-15 Severe Duty – TEFC – NEMA Premium Efficient (RGZEESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-16–7-17 Severe Duty / IEEE 841 – TEFC – NEMA Premium Efficient (SD100 IEEE841) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18 Severe Duty / IEEE 841 – TEFC – NEMA Premium Efficient (RGZEESDX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19–7-20 Severe Duty – TEFC – Inverter Duty – Variable Torque / Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21–7-22 Severe Duty – TEFC – Inverter Duty - 10:1 Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23–7-24 Severe Duty – TEFC & TEBC – Inverter Duty - 1000:1 Constant Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-25–7-26 Hazardous Duty – Inverter Duty – 6:1 Variable Torque or 6:1 Constant Torque . . . . . . . . . . . . . . . . . . . . . . . .7-27–7-28

High | Efficient Motors

Delivery Time Stock and Custom Build Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

Special Options Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-1 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-2–12-10

Typical Performance 1LA7 1LA6 1MJ6/1MJ7 1LA9 1LG6

Dimensions ODP – General Purpose (DP10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 ODP – General Purpose C-Face with Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 ODP – General Purpose D-Flange with Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 TEFC – General Purpose – Cast Aluminum Frame (GP10A/GP100A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4–8-5 TEFC – General Purpose – Cast Iron Frame (GP10/GP100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6–8-7 TEFC – Severe Duty (SD10/SD100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-8–8-9 TEFC – High Efficient – (RGZP/RGZPSD/RGZESD/RGZTESD/RGZZESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10 TEFC – High Efficient – C-Face with and without feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11 TEFC – High Efficient – D-Flange with and without feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12 TEFC – Automotive Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13 TEFC – Brake & Brake Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14 1-2

2007 Low Voltage AC Motors Selection and Pricing Guide

50 Hz & 60 Hz 50 Hz & 60 Hz 50 Hz & 60 Hz 50 Hz & 60 Hz 50 Hz & 60 Hz

. . . . . . . . . . . . . . . . . .13-1–13-2 . . . . . . . . . . . . . . . . . . . . . . .13-3 . . . . . . . . . . . . . . . . . .13-4–13-6 . . . . . . . . . . . . . . . . . .13-7–13-8 . . . . . . . . . . . . . . . . .13-9–13-10

Dimensions 1LA7 1LA6 1MJ6/1MJ7 1LA9 1LG6 1LA6/1LA7/1LA9/1MJ6 1LG6/1MJ6/1MJ7

B3 Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-1 B3 Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-2 B3 Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-3 B3 Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-4 B3 Foot Mounted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-5 B5-B14 Flange w/o feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-6 B5 Flange w/o feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-7 2007 Low Voltage AC Motors Selection and Pricing Guide

1-3

Siemens GPA, GP & SD Series NEMA Motors Features at a Glance High Efficient

Mechanical Data

Electrical Data

GP10A See Page 2-4

1-4

NEMA Premium® Efficient GP10 See Page 2-9

SD10 See Page 2-19

GP100A See Page 3-1

GP100 See Page 3-6

SD100 See Page 3-11

SD100 IEEE841 See Page 3-23

Enclosure

General Purpose - TEFC

General Purpose - TEFC

Severe Duty - TEFC

General Purpose - TEFC

General Purpose - TEFC

Severe Duty - TEFC

Severe Duty / IEEE 841 (2001) - TEFC

Efficiency

High

High

High

Exceeds NEMA Premium

Exceeds NEMA Premium

Exceeds NEMA Premium

Exceeds NEMA Premium

HP Range

1-20

1-20

1-20

1-20

1-20

1-20

1-20

Frame Size

143T-256T

143T-256T

143T-256T

143T-256T

143T-256T

143T-256T

143T-256T

Frequency

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

Power

3 - Phase

3 - Phase

3 - Phase

3 - Phase

3 - Phase

3 - Phase

3 - Phase

Voltage

208-230/460 & 575

208-230/460 & 575

208-230/460 & 575

208-230/460 & 575

208-230/460 & 575

208-230/460 & 575

460 & 575

Service Factor (sine wave) 1.15

1.15

1.15

1.15

1.15

1.15

1.15

Electrical Design

NEMA design B

NEMA design B

NEMA design B

NEMA design B

NEMA design B

NEMA design B

NEMA design B

Stator Windings

Copper - random wound

Copper - random wound

Copper - random wound

Copper - random wound

Copper - random wound

Copper - random wound

Copper - random wound

Insulation

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31 Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Temperature Rise

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.05F, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Warranty

18 Months

18 Months

3 Years

18 Months

18 Months

3 Years

5 Years

Frame

Cast aluminum with bolted feet

Cast iron

Cast iron

Cast aluminum with bolted feet

Cast iron

Cast iron

Cast iron

End Shields

Cast aluminum

Cast iron

Cast iron

Cast aluminum

Cast iron

Cast iron

Cast iron

Conduit Box

Cast aluminum

Cast aluminum

Cast iron

Cast aluminum

Cast aluminum

Cast iron

Cast iron

Lead Seal Gasket

Neoprene (o-rings)

Neoprene

Neoprene

Neoprene (o-ring)

Neoprene

Neoprene

Neoprene

Fan Cover

Plastic

Plastic

Cast iron

Plastic

Plastic

Cast iron

Cast iron

Cooling Fan

Bi-directional - polypropylene

Bi-directional - polypropylene

Bi-directional - polypropylene

Bi-directional - polypropylene

Bi-directional - polypropylene

Bi-directional - polypropylene

Bi-directional - polypropylene

Rotor

Die cast aluminum

Die cast aluminum

Die cast aluminum

Die cast copper

Die cast copper

Die cast copper

Die cast copper, Alum. for 8 pole motors

Shaft

High strength carbon steel (C1045)

High strength carbon steel (C1045)

High strength carbon steel (C1045)

High strength carbon steel (C1045)

High strength carbon steel (C1045)

High strength carbon steel (C1045)

High strength carbon steel (C1045)

Bearing Type

Lubricated for life

Lubricated for life

Double Shielded

Lubricated for life

Lubricated for life

Double Shielded

Single Shielded

Non-regreasable

Non-regreasable

Regreasable inlet & outlet

Non-regreasable

Non-regreasable

Regreasable inlet & outlet

Regreasable inlet & outlet

Bearing Inner Cap

No

No

Cast iron

No

No

Cast iron

Cast iron

Shaft Seal / Slinger

V-ring slinger - DE only

V-ring slinger - DE only

V-ring slinger - DE and ODE

V-ring slinger - DE only

V-ring slinger - DE only

V-ring slinger - DE and ODE

Inpro/Seal® Bearing Isolator DE & ODE

Lubrication

Polyurea

Polyurea

Polyurea

Polyurea

Polyurea

Polyurea

Polyurea

Lube Inlet Fittings

NA

NA

Alemite

NA

NA

Alemite

Alemite

Lube Relief Fittings

NA

NA

Plug

NA

NA

Plug

Pressure relief

Condensation Drain

Drain holes - lowest point (2)

Drain holes - lowest point (2)

T - drains - lowest point (2)

Drain holes - lowest point (2)

Drain holes - lowest point (2)

T-drains - lowest point (2)

T-drains - lowest point (2)

Hardware

Zinc plated

Zinc plated

Zinc plated

Zinc plated

Zinc plated

Zinc plated

Zinc plated

Lifting Eyebolt

Motors > 75 lbs

Motors > 75 lbs

Motors > 75 lbs

Motors > 75 lbs

Motors > 75 lbs

Motors > 75 lbs

Motors > 75 lbs

Nameplate

Aluminum - engraved

Aluminum - engraved

Stainless steel - engraved

Aluminum - engraved

Aluminum - engraved

Stainless steel - engraved

Stainless steel - embossed

Paint

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Epoxy enamel - RAL 9023 Gray

Vibration

0.15 IPS

0.15 IPS

0.08 IPS (2, 4, 6 pole) 0.06 IPS (8 pole)

0.15 IPS

0.15 IPS

0.08 IPS

0.06 IPS

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

1-5

Siemens DP & RG Series NEMA Motors Features at a Glance

Mechanical Data

Electrical Data

High Efficient DP10 See Page 2-1

RGZP See Page 2-14

Enclosure

General Purpose - ODP

General Purpose - TEFC

Severe Duty - TEFC

Efficiency

High

High

High

HP Range

1-500

1-200

Frame Size

140-440

140-440

Frequency

60 Hertz

Power Voltage

3 - Phase 208-230/460 to 100HP (400 frame) 460 only 100HP (440 frame) and above

RGZPSD See Page 2-23

RGZESD See Page 2-26

RGZZESD See Page 2-39

RGZESDI See Page 4-3

RGZZESDI See Page 4-14

RGZEESD See Page 3-15

RGZEESDX See Page 3-26

Severe Duty - TEFC

Hazardous Duty - TEFC

Severe / Inverter Duty - TEFC

Hazardous / Inverter Duty - TEFC

Severe Duty - TEFC

Severe Duty / IEEE 841 (2001) - TEFC

High

High

High

High

NEMA Premium

NEMA Premium

1-200

1-400

1-300

1-400

1-200

1-400

1-400

140-440

140-S440

140-440

140-S440

140-440

140-S440

140-S440

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

60 Hertz

3 - Phase 230/460

3 - Phase 230/460

3 - Phase 230/460

3 - Phase 230/460

3 - Phase 460

3 - Phase 460

3 - Phase 230/460

3 - Phase 460

460 only 100HP and above

460 only 100HP and above

460 only 25HP and above

460 only 25HP and above

460 only 25HP and above

Service Factor (sine wave) Electrical Design

1.15 NEMA design B

1.15 NEMA design B

1.15 NEMA design B

1.15 NEMA design B

1.0 NEMA design B

1.15 (sine wave), 1.0 (VFD) NEMA design B (except for derates)

Stator Windings

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Insulation

Class F, meets NEMA MG1-2003, Class F, meets NEMA MG1-2003, Class F, meets NEMA MG1-2003, Class F, meets NEMA MG1-2003, Part 31 (140-400) and Part 30 (440) Part 30 Part 30 Part 31

Class F

1.0 NEMA design B (except for derates)

1.15 NEMA design B (except as noted)

1.15 NEMA design B (except as noted)

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Class F, meets NEMA MG1-2003, Part 31

Temperature Rise (sine wave) Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF Class B @ 1.0SF, Class F @ 1.15SF Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF

Class B @ 1.0SF & Class F @ 1.15SF

Class B @ 1.0SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Warranty Frame End Shields

18 Months Cast Iron Cast Iron

18 Months Cast Iron 140-250 Aluminum 280-440 Cast Iron

18 Months Cast Iron Cast Iron

3 Years Cast Iron Cast Iron

3 Years Cast Iron Cast Iron

3 Years Cast Iron Cast Iron

3 Years Cast Iron Cast Iron

3 Years Cast Iron Cast Iron

5 Years Cast Iron Cast Iron

Conduit Box

140-400 Steel 440 Cast Iron

140-250 Aluminum 280-400 Steel, 440 Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Lead Seal Gasket Fan Cover

Neoprene Not Applicable

Neoprene 140-365 Polycarbonate 400-440 Cast Iron

Neoprene Cast Iron

Neoprene Cast Iron

Cast Iron

Neoprene Cast Iron

Cast Iron

Neoprene Cast Iron

Neoprene Cast Iron

Cooling Fan

Not Applicable

Bi-directional, Polypropylene

Bi-directional, Polypropylene

140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze

Bi-directional, Polypropylene

Bi-directional, Polypropylene

Bi-directional, Polypropylene

140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze

140-440 Bi-directional, Polypropylene S440 Locked & Keyed Bronze

Rotor

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Shaft Bearing Type

High Strength Carbon Steel (C1045) 140-280 Lubricated for Life 320-440 Double Shielded

High Strength Carbon Steel (C1045) High Strength Carbon Steel (C1045) High Strength Carbon Steel (C1045) 140-250 Lubricated for Life Single Shielded Single Shielded 280-440 Single Shielded

High Strength Carbon Steel (C1045) High Strength Carbon Steel (C1045) Single Shielded Single Shielded

High Strength Carbon Steel (C1045) Single Shielded

High Strength Carbon Steel (C1045) Single Shielded

High Strength Carbon Steel (C1045) Single Shielded

Bearing Inner Cap Shaft Seal / Slinger

320-440 Stationary Bearing Caps

440 Stationary Bearing Caps 280-440 V-Ring Slinger DE

Lubrication

140-400 Lithium 440 Polyurea

Lube Inlet Fittings Lube Relief Fittings

Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea

Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea

Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea

Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger DE Polyurea

Stationary Bearing Caps V-Ring Slinger DE & ODE

Stationary Bearing Caps Inpro/Seal® Bearing Isolator DE & ODE

Polyurea

400-440 Stationary Bearing Caps 140-250 Shaft Seal DE 280-440 V-Ring Slinger Polyurea

Polyurea

Polyurea

320-440 Alemite

280-440 Alemite

Alemite

Alemite

Alemite

Alemite

Alemite

Alemite

Alemite

Plug

280-440 Plug

Plug

Plug

Plug

Plug

Plug

Plug

Pressure Relief

140-360 Hole 400-440 T-Drain

T-Drain

T-Drain

400-440 Only

T-Drain

400-440 Only

T-Drain

T-Drain

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-180 Provisions 210-440 Included

Zinc Plated 140-440 Included

Zinc Plated 140-440 Included

Condensation Drain

1-6

NEMA Premium® Efficient

Hardware Lifting Eyebolt

Zinc Plated 180-440 Included

Nameplate Paint

Stainless Steel - Engraved Aluminum - Engraved 140-400 Polyurethane - RAL 9023 Gray Epoxy Enamel - RAL 5001 Blue 440 Epoxy Enamel - RAL 9023 Gray

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Engraved Epoxy Enamel - RAL 5001 Blue

Stainless Steel - Embossed Epoxy Enamel -RAL 5001 Blue

Vibration

0.15 IPS

0.08 IPS

0.08 IPS

0.08 IPS

0.06 IPS

0.06 IPS

0.08 IPS

0.06 IPS

0.08 IPS

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

1-7

Siemens Vertical P-Base NEMA Motors Features at a Glance High Efficient

Mechanical Data

Electrical Data

HRGZVESD See Page 2-73

1-8

Enclosure Efficiency Thrust HP Range Frame Size Frequency Power Voltage

Severe Duty - TEFC High High 25-250 284TP-449TP 60 Hertz 3 - Phase 230/460 460 only 100HP and above Service Factor (sine wave) 1.15 Electrical Design NEMA design B Stator Windings Copper - Random Wound Insulation Class F, meets NEMA MG1-2003, Part 31 Temperature Rise Class B @ 1.0SF, Class F @ 1.15SF Warranty 3 Years Frame Cast Iron End Shields Cast Iron Conduit Box Oversized Cast Iron Lead Seal Gasket Neoprene Fan Cover Cast Iron Cooling Fan 284-449TP Bi-directional, Polypropylene Drip Cover Steel Rotor Die Cast Aluminum Shaft Hollow - High Strength Carbon Steel (C1045) Bearing Type (DE) 284-449TP open ball bearing

Bearing Type (ODE)

284-449TP angular contact thrust bearing

Bearing Inner Cap Shaft Seal / Slinger

Stationary Bearing Caps 284-449TP V-Ring Slinger

Lubrication Lube Inlet Fittings Lube Relief Fittings Condensation Drain Hardware Lifting Lugs Nameplate Paint Vibration

Polyurea Alemite Plug T-Drain Zinc Plated 284-449TP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

2007 Low Voltage AC Motors Selection and Pricing Guide

RGZVESD See Page 2-55

RGZZVESD See Page 2-58

Severe Duty - TEFC High Normal 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 143-256HP open ball bearing 284-365HP single shielded ball bearing 404-405HP double shielded ball bearing 444-449HP open ball bearing 143-365HP open ball bearing 404-405HP double shielded ball bearing 444-449HP single shielded ball bearing

Hazardous Duty - TEFC High Normal 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.0 NEMA design B Copper - Random Wound Class F Class B @ 1.0SF 3 Years Cast Iron Cast Iron Oversized Cast Iron None Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel(C1045) 143-256HP open ball bearing 284-365HP single shielded ball bearing 404-405HP double shielded ball bearing 444-449HP open ball bearing 143-365HP open ball bearing 404-405HP double shielded ball bearing 444-449HP single shielded ball bearing

Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449HP only) Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

RGZVMTESD See Page 2-61

RGZZVMTESD See Page 2-64

RGZVILESD See Page 2-67

RGZZVILESD See Page 2-70

Severe Duty - TEFC High Medium 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.15 NEMA design B Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class B @ 1.0SF, Class F @ 1.15SF 3 Years Cast Iron Cast Iron Oversized Cast Iron Neoprene Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel (C1045) 143-256HP open ball bearing 284-365HP double shielded ball bearing 404-449HP angular contact thrust bearing

Hazardous Duty - TEFC High Medium 1-250 143HP-449HP 60 Hertz 3 - Phase 230/460 460 only 25HP and above 1.0 NEMA design B Copper - Random Wound Class F Class B @ 1.0SF 3 Years Cast Iron Cast Iron Oversized Cast Iron None Cast Iron 143-449HP Bi-directional, Polypropylene Steel Die Cast Aluminum Solid - High Strength Carbon Steel (C1045) 143-256HP open ball bearing 284-365HP double shielded ball bearing 404-449HP angular contact thrust bearing

Severe Duty - TEFC Hazardous Duty - TEFC High High In-Line In-Line 3-250 3-250 182LP-449LP 182LP-449LP 60 Hertz 60 Hertz 3 - Phase 3 - Phase 230/460 230/460 460 only 25HP and above 460 only 25HP and above 1.15 1.0 NEMA design B NEMA design B Copper - Random Wound Copper - Random Wound Class F, meets NEMA MG1-2003, Part 31 Class F Class B @ 1.0SF, Class F @ 1.15SF Class B @ 1.0SF 3 Years 3 Years Cast Iron Cast Iron Cast Iron Cast Iron Oversized Oversized Cast Iron Cast Iron Neoprene None Cast Iron Cast Iron 182-449LP Bi-directional, Polypropylene 182-449LP Bi-directional, Polypropylene Cast Iron Cast Iron Die Cast Aluminum Die Cast Aluminum Solid - High Strength Carbon Steel (C1045) Solid - High Strength Carbon Steel (C1045) 182-256LP open ball bearing 182-256LP open ball bearing 284-449LP double shielded ball bearing 284-449LP double shielded ball bearing

143-256HP angular contact thrust bearing 284-365HP angular contact thrust bearing and four-point ball bearing 404-449HP double sheilded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

143-256HP angular contact thrust bearing 284-365HP angular contact thrust bearing and four-point ball bearing 404-449HP double sheilded ball bearing Stationary Bearing Caps 143-256HP Shaft Seal 284-365HP None 404-449HP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449HP only) Zinc Plated 143-449HP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

182-449LP duplex angular contact thrust bearing

182-449LP duplex angular contact thrust bearing

Stationary Bearing Caps 182-256LP Shaft Seal 284-365LP None 404-449LP V-Ring Slinger Polyurea Alemite Plug T-Drain Zinc Plated 182-449LP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

Stationary Bearing Caps 182-256LP Shaft Seal 284-365LP None 404-449LP V-Ring Slinger Polyurea Alemite Plug U.L. Listed (404-449LP only) Zinc Plated 182-449LP Included Stainless Steel - engraved Epoxy Enamel - RAL 5001 Blue 0.08 IPS

2007 Low Voltage AC Motors Selection and Pricing Guide

1-9

Note: A minimum charge of $100 will be assessed for any order cancellation for modified or custom motors.

Stock Motors: • •

No charges will be incurred if an order is cancelled prior to shipment. A stock motor is returnable (freight paid by purchaser) immediately after shipment if returned in “new” condition (original, undamaged packaging) for a minimum restocking charge of 20% of the motor net price.

Non-Stock Motors: •

For non-stock motors, the following graph will apply to determine cancellation charges after the order is received and entered at the factory. Completion progress will be determined by a Siemens Customer Service Representative. A charge of 15% of the total net motor price will be assessed if an order is cancelled after it has been released for engineering and drafting whether or not the drawings have been completed and/or submitted for approval.

To meet your cost of ownership and motor management needs, Siemens offers several levels of energy efficiency in many of its motors: • High • NEMA Premium • Inverter Duty

Total Customer Support When you’re looking for a motor, look for a highly trained specialist to help you match the right motor to your specific needs. Siemens sales engineers share the knowledge, training and experience to help you solve performance or installation challenges to ensure that you will receive the best value for your investment.

90%

Availability

70% 60% 50% 40% 30% 20% 10% 0% 0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

% OF COMPLETION

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Siemens has hundreds of distributor stocking locations throughout North America with a wide selection of NEMA motor sizes and ratings. Motors are available same day from a local source you can trust.

These distributors are supported by multiple stocking centers and our customer service centers in Little Rock and Cincinnati. Need something special? Our modification centers have complete motor modification capabilities to help you get the exact motor you need, when you need it.

80%

HIGH EFFICIENT P-Base Vertical

Our customer service center takes pride in putting our customers first. Whether it’s an expedited shipment, tracking your order, or making sure your motor is properly installed, these professionals won’t be satisfied until you are.

100%

% OF SELLING PRICE

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

CANCELLATION CHARGES

HIGH EFFICIENT Definite Purpose

CHANGE NOTICE All change notices applied to in-process orders logged into the Siemens customer service department and requiring a product change will be subject to a $100 net charge plus the applicable modification adder. Delivery dates will be adjusted according to the type of change/modification requested. This policy does not pertain to commercial changes such as “ship to” or “bill to” addresses.

1-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

1-11

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

These advanced motor designs are manufactured in a state-of-the-art ISO 9001 certified facility. Here, our manufacturing technicians subject each motor to more than 100 separate quality inspections before it leaves our plant. . . and before it is good enough to be offered to you.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

The quality of our motors begins with the design experience we have gained through more than 100 years of manufacturing and applying motors. We build on this experience every day with new designs that incorporate the latest materials and techniques to provide even higher levels of performance, operating efficiency and reliability.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Providing value also means having the right motor for the job. At Siemens, we offer hundreds of motor types, sizes, ratings and modifications. And, as you read these words, we are adding to this list as part of our commitment to become your single source for motors.

CANCELLATION CHARGES & CHANGE NOTICES

HIGH EFFICIENT Severe Duty

Iron-clad Quality

HIGH EFFICIENT General Purpose

Wide Selection

The Right Efficiency for Your Application

Introduction

Siemens

Siemens

General Purpose - ODP Motors DP10

HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty HIGH EFFICIENT P-Base Vertical

Lubrication – Lithium-based lubrication is used for 140-400 frame motors. Frame 440 motors use a specially formulated, high-temperature-tested, polyurea-based grease to provide more than four times the lubrication life of other polyurea greases.

Corrosion Resistance – Cast iron construction, zinc-plated hardware, polyurethane finish paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

Rotor – Die cast aluminum rotor bars with integrally cast end rings and cooling fins. Optimum slot design contributes to higher torque, low temperature rise and quiet operation. Each rotor is dynamically balanced for extended bearing life, and includes a high-strength carbon steel (C1045) shaft for maximum rotor performance.

Bearings – Oversized, lubricated for life (140-280 frames) and oversized, regreasable (320-440 frames), with inlet grease fitting and relief port plug for ease of routine maintenance. In addition, frames 320-440 are fitted with stationary bearing caps (DE only for 320 frames).

Oversized Conduit Box – Larger than industry standards, diagonally-split, neoprene-gasketed to the frame and rotatable in 90º increments for quick and easy connections. Also includes a ground lug and non-wicking, clearly and permanently marked leads. Sheet steel for 140-400 frames, cast iron construction for 440 frames.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

1-12

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-1

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction for exceptional structural integrity. Lifting eyebolts are included with 180-440 frame motors.

Cooling – Type DP10 motors are designed and built with excellent ventilation and heat dissipation qualities.

HIGH EFFICIENT Hazardous Duty

Features for Long Life:

Insulation – Inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise provides an extra margin of thermal life. This insulation system is suitable for operation with variable frequency drives.

HIGH EFFICIENT Multi Speed

• 1 to 500 HP • 1.15 service factor, 40ºC ambient • 3600, 1800, 1200 or 900 RPM • 3-phase, 60 Hz; 208-230/460 volt operation to 100 HP (400 frame), 460 volt 100 HP (440 frame) and above; 575 volt available (440 frames only) • Meets or exceeds EPAct efficiency standards • Class F insulation, Class B temperature rise • NEMA design B, continuous duty • 143T through 449T frame

HIGH EFFICIENT Severe Duty

Performance Specifications

Stator/Windings – Manufactured with premium electrical-grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross-section reduces resistance and lowers stator losses.

HIGH EFFICIENT General Purpose

These motors are designed for rugged performance and long life in applications where ambient contamination from moisture, dust, dirt or grit is minimal. They are costeffective solutions to power pumps, fans, compressors, material handling and other industrial applications.

HIGH EFFICIENT General Purpose

Introduction

Introduction

Notes

Introduction HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Multiplier Symbol

FL Amps 460V

FL Nom. Weight Stock Eff. (%) (lbs.) Model

HP

RPM

Frame

Voltage

Type

Part Number

RPM

Frame

Voltage

Type

1

1800

143T

208-230/460

DP10

Ball

1LE20021AB214AA3

224

SA-7OD

1.5

82.5

35

✔

75

3600

364TS

208-230/460

DP10

Ball

1LE20023DA314AA3

3260

SA-7OD

87

93

650

✔

1

1200

145T

208-230/460

DP10

Ball

1LE20021AC314AA3

289

SA-7OD

1.9

80

40

✔

75

1800

365TS

208-230/460

DP10

Ball

1LE20023DB214AA3

3027

SA-7OD

89

94.1

705

✔

1.5

3600

143T

208-230/460

DP10

Ball

1LE20021AA214AA3

246

SA-7OD

2.1

82.5

35

✔

75

1800

365T

208-230/460

DP10

Ball

1LE20023CB214AA3

3027

SA-7OD

89

94.1

705

✔

40

✔

75

1200

405T

208-230/460

DP10

Ball

1LE20024AC214AA3

4498

SA-7OD

91

93.6

945

✔

75

✔

100

3600

365TS

208-230/460

DP10

Ball

1LE20023DA414AA3

4482

SA-7OD

115

93.6

710

✔

1800

404TS

208-230/460

DP10

Ball

1LE20024BB314AA3

3901

SA-7OD

117

94.5

850

✔

1800 1200

145T 182T

208-230/460 208-230/460

DP10 DP10

Ball Ball

1LE20021AB314AA3 1LE20021CC114AA3

246 318

SA-7OD SA-7OD

2.1 2.6

84 85.5

HP

Part Number

SA-7OD

2.7

84

40

✔

1LE20021AB414AA3

271

SA-7OD

2.8

84

40

✔

100

1800

404T

208-230/460

DP10

Ball

1LE20024AB714AA3

3901

SA-7OD

117

94.5

850

✔

1LE20021CC314AA3

325

SA-7OD

3.5

86.5

85

✔

100

1200

444T

460 PWS

DP10

Roller

1RA04446DEC1

5699

SA-7OD

116

94.1

1185

✔

Ball

1LE20021AA414AA3

325

SA-7OD

4

85.5

40

✔

100

900

445T

460

DP10

Roller

7760

SA-7OD

126

93.6

1300

DP10

Ball

1LE20021CB114AA3

282

SA-7OD

4.2

87.5

75

✔

125

3600

404TS

460

DP10

Ball

1LE20024BA312AA3

5514

SA-7OD

144

94.5

855

✔

DP10

Ball

1LE20022AC114AA3

451

SA-7OD

4.4

87.5

115

✔

125

1800

405TS

460

DP10

Ball

1LE20024BB412AA3

4487

SA-7OD

144.5

94.5

930

✔

208-230/460

DP10

Ball

1LE20021CA214AA3

395

SA-7OD

6.4

87.5

75

✔

125

1800

405T

460

DP10

Ball

1LE20024AB812AA3

4487

SA-7OD

144.5

94.5

930

✔

184T

208-230/460

DP10

Ball

1LE20021CB314AA3

355

SA-7OD

6.7

87.5

85

✔

125

1200

445T

460 PWS

DP10

Roller

1RA04456DEC1

6933

SA-7OD

145

94.1

1300

✔

1200

215T

208-230/460

DP10

Ball

1LE20022AC214AA3

625

SA-7OD

7.1

87.5

130

✔

125

900

447T

460

DP10

Roller

8573

SA-7OD

152

94.1

1680

7.5

3600

184T

208-230/460

DP10

Ball

1LE20021CA414AA3

470

SA-7OD

8.9

88.5

85

✔

150

3600

405TS

460

DP10

Ball

1LE20024BA412AA3

7131

SA-7OD

171.5

94.5

940

✔

7.5

1800

213T

208-230/460

DP10

Ball

1LE20022AB114AA3

514

SA-7OD

9.5

89.5

115

✔

150

1800

444TS

460 PWS

DP10

Ball

1RA04444DEC2

6451

SA-7OD

190

95

1185

✔

7.5

1200

254T

208-230/460

DP10

Ball

1LE20022BC114AA3

797

SA-7OD

10.5

89.5

210

✔

150

1800

444T

460 PWS

DP10

Roller

1RA04444DEC1

6451

SA-7OD

190

95

1185

✔

3600

213T

208-230/460

DP10

Ball

1LE20022AA714AA3

591

SA-7OD

12.5

89.5

115

✔

150

1800

444T

460 Y/D

DP10

Roller

1RA04444DEG1

6451

SA-7OD

190

95

1185

✔

130

✔

150

1200

445T

460 PWS

DP10

Roller

1RA04456DFC1

7636

SA-7OD

174

94.5

1300

✔

900

447T

460

DP10

Roller

9672

SA-7OD

188

94.1

1680

3600

444TS

460 Y/D

DP10

Ball

1RA04442DEG2

9377

SA-7OD

223

94.5

1185

✔

2

3600

145T

208-230/460

DP10

Ball

1LE20021AA314AA3

2

1800

145T

208-230/460

DP10

Ball

2

1200

184T

208-230/460

DP10

Ball

3

3600

145T

208-230/460

DP10

3

1800

182T

208-230/460

3

1200

213T

208-230/460

5

3600

182T

5

1800

5

10

1800

215T

208-230/460

DP10

Ball

1LE20022AB214AA3

601

SA-7OD

13

89.5

256T

208-230/460

DP10

Ball

1LE20022BC214AA3

925

SA-7OD

13.5

89.5

240

✔

3600

215T

208-230/460

DP10

Ball

1LE20022AA814AA3

802

SA-7OD

18.5

90.2

130

✔

200

15

1800

254T

208-230/460

DP10

Ball

1LE20022BB114AA3

792

SA-7OD

19

91

210

✔

200

1800

445TS

460 PWS

DP10

Ball

1RA04454DEC2

7865

SA-7OD

235

95

1300

✔

15

1200

284T

208-230/460

DP10

Ball

1LE20022CC114AA3

1261

SA-7OD

20.3

90.2

322

✔

200

1800

445T

460 PWS

DP10

Roller

1RA04454DEC1

7865

SA-7OD

235

95

1300

✔

20

3600

254T

208-230/460

DP10

Ball

1LE20022BA714AA3

943

SA-7OD

24

90.2

210

✔

200

1800

445T

460 Y/D

DP10

Roller

1RA04454DEG1

7865

SA-7OD

235

95

1300

✔

20

1800

256T

208-230/460

DP10

Ball

1LE20022BB214AA3

986

SA-7OD

25

91

240

✔

200

1200

447T

460 PWS

DP10

Roller

1RA04476DGC1

9975

SA-7OD

232

94.5

1680

✔

20

1200

286T

208-230/460

DP10

Ball

1LE20022CC214AA3

1695

SA-7OD

26

90.2

393

✔

200

900

449T

460

DP10

Roller

10355

SA-7OD

253

94.5

2000

25

3600

256T

208-230/460

DP10

Ball

1LE20022BA814AA3

1150

SA-7OD

30

91

240

✔

250

3600

445TS

460 Y/D

DP10

Ball

1RA04452DPG2

10032

SA-7OD

277

94

1300

✔

25

1800

284TS

208-230/460

DP10

Ball

1LE20022DB114AA3

1162

SA-7OD

31

92.4

312

✔

250

1800

445TS

460 PWS

DP10

Ball

1RA04454DRC2

8863

SA-7OD

315

94

1300

✔

25

1800

284T

208-230/460

DP10

Ball

1LE20022CB114AA3

1162

SA-7OD

31

92.4

312

✔

250

1800

445T

460 PWS

DP10

Roller

1RA04454DRC1

8863

SA-7OD

315

94

1300

✔

25

1200

324T

208-230/460

DP10

Ball

1LE20023AC114AA3

1951

SA-7OD

31

91.7

495

✔

250

1800

445T

460 Y/D

DP10

Roller

1RA04454DYG1

8863

SA-7OD

315

94

1300

✔

30

3600

284TS

208-230/460

DP10

Ball

1LE20022DA314AA3

1307

SA-7OD

36

91

322

✔

250

1200

449T

460 PWS

DP10

Roller

1RA04496DRC1

9810

SA-7OD

288

95

2000

✔

30

1800

286TS

208-230/460

DP10

Ball

1LE20022DB214AA3

1357

SA-7OD

36.5

92.4

385

✔

300

3600

447TS

460 Y/D

DP10

Ball

1RA04472DPG2

11781

SA-7OD

335

93

1680

✔

385

✔

300

1800

447TS

460 PWS

DP10

Ball

1RA04474DRC2

9832

SA-7OD

364

94.1

1680

✔

545

✔

300

1800

447T

460 PWS

DP10

Roller

1RA04474DRC1

9832

SA-7OD

364

94.1

1680

✔

1200

449T

460

DP10

Roller

11392

SA-7OD

351

94.1

2000

13494

SA-7OD

389

93.6

1680

11500

SA-7OD

433

94.5

1680

11500

SA-7OD

433

94.5

1680

15354

SA-7OD

442

94.1

2000

14500

SA-7OD

495

94.5

2000 2000

30 30

1800 1200

286T 326T

208-230/460 208-230/460

DP10 DP10

Ball Ball

1LE20022CB214AA3 1LE20023AC214AA3

1357 1970

SA-7OD SA-7OD

36.5 37

92.4 91.7

40

3600

286TS

208-230/460

DP10

Ball

1LE20022DA414AA3

1778

SA-7OD

48

91.7

393

✔

300

40

1800

324TS

208-230/460

DP10

Ball

1LE20023BB114AA3

1692

SA-7OD

49

93

490

✔

350

3600

447TS

460 Y/D

DP10

Ball

40

1800

324T

208-230/460

DP10

Ball

1LE20023AB114AA3

1692

SA-7OD

49

93

490

✔

350

1800

447TS

460

DP10

Ball

40

1200

364T

208-230/460

DP10

Ball

1LE20023CC114AA3

2790

SA-7OD

50

93

650

✔

350

1800

447T

460

DP10

Roller

50

3600

324TS

208-230/460

DP10

Ball

1LE20023BA314AA3

2155

SA-7OD

59

92.4

495

✔

400

3600

449TS

460 Y/D

DP10

Ball

50

1800

326TS

208-230/460

DP10

Ball

1LE20023BB214AA3

1941

SA-7OD

61

93

535

✔

400

1800

449TS

460

DP10

Ball

50

1800

326T

208-230/460

DP10

Ball

1LE20023AB214AA3

1941

SA-7OD

61

93

535

✔

400

1800

449T

460

DP10

Roller

14500

SA-7OD

495

94.5

50

1200

365T

208-230/460

DP10

Ball

1LE20023CC214AA3

3511

SA-7OD

52

93

710

✔

450

3600

449TS

460 Y/D

DP10

Ball

1RA04492DXG2

15654

SA-7OD

487

95

2000

✔

60

3600

326TS

208-230/460

DP10

Ball

1LE20023BA414AA3

2582

SA-7OD

70

93

545

✔

500

3600

449TS

460 Y/D

DP10

Ball

1RA04492DYG2

17018

SA-7OD

570

94.8

2000

✔

60

1800

364TS

208-230/460

DP10

Ball

1LE20023DB114AA3

2380

SA-7OD

72

93.6

640

✔

60

1800

364T

208-230/460

DP10

Ball

1LE20023CB114AA3

2380

SA-7OD

72

93.6

640

✔

60

1200

404T

208-230/460

DP10

Ball

1LE20024AC114AA3

3742

SA-7OD

73

93.6

855

✔

DOE#CC014A (140-400 frames) DOE#CC032A (440 frames)

✔

Notes: 1. 575V available upon request for 440 frames only. 2. Shaded ratings are not in the scope of EPAct regulations.

DOE#CC014A (140-400 frames) DOE#CC032A (440 frames)

2007 Low Voltage AC Motors Selection and Pricing Guide

2-3

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

1RA04492DPG2

✔

NEMA PREMIUM General Purpose

2-2

1RA04472DXG2

HIGH EFFICIENT P-Base Vertical

1200

15

HIGH EFFICIENT Definite Purpose

10

150

HIGH EFFICIENT Hazardous Duty

289

100

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

List Price $

DE Bearing

Multiplier Symbol

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

FL Nom. Weight Stock Eff. (%) (lbs.) Model

Stock/Modifiable

List Price $

10

HIGH EFFICIENT P-Base Vertical

FL Amps 460V

DP10

DE Bearing

1.5

NEMA PREMIUM General Purpose

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT General Purpose

DP10

1.5

NEMA PREMIUM Severe Duty

General Purpose - ODP Motors

Introduction

General Purpose - ODP Motors

Introduction HIGH EFFICIENT General Purpose

GP10A (Cast Aluminum Frame)

GP10A (Cast Aluminum Frame)

The new GP10A series of TEFC motors is ideal for material handling, pump, fan, compressor and other general purpose industrial applications.

Performance Specifications

Frame & End Shields - Die cast aluminum construction for exceptional heat dissipation and structural integrity, equipped with bolt-on feet and condensation drain holes. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Polycarbonate fan covers are provided on all frame sizes.

•

Rotor - A unique offset rotor bar design provides improved efficiency. Large cross section bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Bearings - Lubricated for life, oversized, complete with external bearing protection. Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

Oversized Conduit Box - Cast aluminum construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - Die cast aluminum construction, structural foam fan and fan cover, zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist corrosion. Modifiable - Siemens GP10A motors are available with a variety of modifications and kits.

1

3600

143T

208-230/460

GP10A

Ball

1LE21011AA114AA3

267

GPA1

1.4

80

32

✔

1

3600

143T

575

GP10A

Ball

1LE21011AA113AA3

267

GPA1

1.12

80

32

✔ ✔

1

1800

143T

208-230/460

GP10A

Ball

1LE21011AB214AA3

267

GPA1

1.5

82.5

34

1

1800

143T

575

GP10A

Ball

1LE21011AB213AA3

267

GPA1

1.2

82.5

34

✔

1

1200

145T

208-230/460

GP10A

Ball

1LE21011AC314AA3

333

GPA1

1.6

80

35

✔

1

1200

145T

575

GP10A

Ball

1LE21011AC313AA3

333

GPA1

1.28

80

35

✔

1

900

182T

208-230/460

GP10A

Ball

1LE21011CD114AA3

521

GPA1

2.1

81.5

57

✔

1

900

182T

575

GP10A

Ball

1LE21011CD113AA3

521

GPA1

1.64

81.5

57

✔

1.5

3600

143T

208-230/460

GP10A

Ball

1LE21011AA214AA3

274

GPA1

2

82.5

33

✔ ✔

1.5

3600

143T

575

GP10A

Ball

1LE21011AA213AA3

274

GPA1

1.6

82.5

33

1.5

1800

145T

208-230/460

GP10A

Ball

1LE21011AB314AA3

295

GPA1

2.2

84

38

✔

1.5

1800

145T

575

GP10A

Ball

1LE21011AB313AA3

295

GPA1

1.76

84

38

✔

1.5

1200

182T

208-230/460

GP10A

Ball

1LE21011CC114AA3

355

GPA1

2.4

85.5

54

✔

1.5

1200

182T

575

GP10A

Ball

1LE21011CC113AA3

355

GPA1

1.92

85.5

54

✔

1.5

900

184T

208-230/460

GP10A

Ball

1LE21011CD314AA3

565

GPA1

3

82.5

71

✔

1.5

900

184T

575

GP10A

Ball

1LE21011CD313AA3

565

GPA1

2.4

82.5

71

✔

2

3600

145T

208-230/460

GP10A

Ball

1LE21011AA314AA3

319

GPA1

2.6

84

35

✔

2

3600

145T

575

GP10A

Ball

1LE21011AA313AA3

319

GPA1

2.08

84

35

✔

2

1800

145T

208-230/460

GP10A

Ball

1LE21011AB414AA3

320

GPA1

3

84

40

✔ ✔

2

1800

145T

575

GP10A

Ball

1LE21011AB413AA3

320

GPA1

2.4

84

40

2

1200

184T

208-230/460

GP10A

Ball

1LE21011CC314AA3

393

GPA1

3.1

86.5

65

✔

2

1200

184T

575

GP10A

Ball

1LE21011CC313AA3

393

GPA1

2.48

86.5

65

✔

2

900

213T

208-230/460

GP10A

Ball

1LE21012AD114AA3

650

GPA1

3.3

84

75

✔

2

900

213T

575

GP10A

Ball

1LE21012AD113AA3

650

GPA1

2.64

84

75

✔

3

3600

182T

208-230/460

GP10A

Ball

1LE21011CA114AA3

355

GPA1

3.7

85.5

56

✔

3

3600

182T

575

GP10A

Ball

1LE21011CA113AA3

355

GPA1

2.96

85.5

56

✔

3

1800

182T

208-230/460

GP10A

Ball

1LE21011CB114AA3

367

GPA1

4

87.5

59

✔

3

1800

182T

575

GP10A

Ball

1LE21011CB113AA3

367

GPA1

3.2

87.5

59

✔

3

1200

213T

208-230/460

GP10A

Ball

1LE21012AC114AA3

505

GPA1

4

87.5

85

✔ ✔

3

1200

213T

575

GP10A

Ball

1LE21012AC113AA3

505

GPA1

3.36

87.5

85

3

900

215T

208-230/460

GP10A

Ball

1LE21012AD214AA3

931

GPA1

4.8

85.5

89

✔

3

900

215T

575

GP10A

Ball

1LE21012AD213AA3

931

GPA1

3.84

85.5

89

✔ ✔

5

3600

184T

208-230/460

GP10A

Ball

1LE21011CA314AA3

463

GPA1

6.2

87.5

62

5

3600

184T

575

GP10A

Ball

1LE21011CA313AA3

463

GPA1

4.96

87.5

62

✔

5

1800

184T

208-230/460

GP10A

Ball

1LE21011CB314AA3

419

GPA1

6.7

87.5

66

✔

5

1800

184T

575

GP10A

Ball

1LE21011CB313AA3

419

GPA1

5.36

87.5

66

✔

5

1200

215T

208-230/460

GP10A

Ball

1LE21012AC214AA3

753

GPA1

6.8

87.5

100

✔

5

1200

215T

575

GP10A

Ball

1LE21012AC213AA3

753

GPA1

5.44

87.5

100

✔

5

900

254T

208-230/460

GP10A

Ball

1LE21012BD114AA3

1362

GPA1

8.8

86.5

157

✔

5

900

254T

575

GP10A

Ball

1LE21012BD113AA3

1362

GPA1

7.04

86.5

157

✔

7.5

3600

213T

208-230/460

GP10A

Ball

1LE21012AA114AA3

605

GPA1

9

88.5

96

✔

7.5

3600

213T

575

GP10A

Ball

1LE21012AA113AA3

605

GPA1

7.2

88.5

96

✔

7.5

1800

213T

208-230/460

GP10A

Ball

1LE21012AB114AA3

586

GPA1

9.5

89.5

102

✔

7.5

1800

213T

575

GP10A

Ball

1LE21012AB113AA3

586

GPA1

7.6

89.5

102

✔

7.5

1200

254T

208-230/460

GP10A

Ball

1LE21012BC114AA3

1010

GPA1

10.5

89.5

163

✔

7.5

1200

254T

575

GP10A

Ball

1LE21012BC113AA3

1010

GPA1

8.4

89.5

163

✔

7.5

900

256T

208-230/460

GP10A

Ball

1LE21012BD214AA3

1422

GPA1

13

87.5

189

✔

7.5

900

256T

575

GP10A

Ball

1LE21012BD213AA3

1422

GPA1

10.4

87.5

189

✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-4

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-5

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Part Number

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Type

HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

• •

Voltage

FL Nom. Eff. (%)

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Multi Speed

•

Frame

Multiplier FL Symbol Amps*

HIGH EFFICIENT Hazardous Duty

Features for Long Life

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31 making all motors suitable for operation with variable frequency drives.

RPM

List Price $

HIGH EFFICIENT Multi Speed

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800, 1200 or 900 RPM 3 phase, 60 Hz; 208-230/460 and 575 volt operation Meets or exceeds EPAct efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 143T through 256T frame

HP

DE Bearing

HIGH EFFICIENT Severe Duty

• • • •

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Price $

FL Multiplier FL Nom. Symbol Amps* Eff. (%)

Weight (lbs.)

Stock Model

HP

RPM

Frame

Voltage

Type

Stock/Modifiable

DE Bearing

Part Number

List Price $

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model ✔

C-Face, Horizontal, Foot Mounted - continued

Horizontal, Foot Mounted - continued 10

3600

215T

208-230/460

GP10A

Ball

1LE21012AA214AA3

713

GPA1

11.5

89.5

113

✔

5

3600

184TC

208-230/460

GP10A

Ball

1LE21011CA314EA3

546

GPA1

6.2

87.5

62

10

3600

215T

575

GP10A

Ball

1LE21012AA213AA3

713

GPA1

9.2

89.5

113

✔

5

3600

184TC

575

GP10A

Ball

1LE21011CA313EA3

546

GPA1

4.96

87.5

62

10

1800

215T

208-230/460

GP10A

Ball

1LE21012AB214AA3

713

GPA1

12.5

89.5

114

✔

5

1800

184TC

208-230/460

GP10A

Ball

1LE21011CB314EA3

502

GPA1

6.7

87.5

66

10

1800

215T

575

GP10A

Ball

1LE21012AB213AA3

713

GPA1

10

89.5

114

✔

5

1800

184TC

575

GP10A

Ball

1LE21011CB313EA3

502

GPA1

5.36

87.5

66

10

1200

256T

208-230/460

GP10A

Ball

1LE21012BC214AA3

1187

GPA1

13.5

89.5

175

✔

5

1200

215TC

208-230/460

GP10A

Ball

1LE21012AC214EA3

836

GPA1

6.8

87.5

100

10

1200

256T

575

GP10A

Ball

1LE21012BC213AA3

1187

GPA1

10.8

89.5

175

✔

5

1200

215TC

575

GP10A

Ball

1LE21012AC213EA3

836

GPA1

5.44

87.5

100

15

3600

254T

208-230/460

GP10A

Ball

1LE21012BA114AA3

979

GPA1

18

90.2

168

✔

5

900

254TC

208-230/460

GP10A

Ball

1LE21012BD114EA3

1471

GPA1

8.8

86.5

157

15

3600

254T

575

GP10A

Ball

1LE21012BA113AA3

979

GPA1

14.4

90.2

168

✔

5

900

254TC

575

GP10A

Ball

1LE21012BD113EA3

1471

GPA1

7.04

86.5

157

15

1800

254T

208-230/460

GP10A

Ball

1LE21012BB114AA3

956

GPA1

19

91

166

✔

7.5

3600

213TC

208-230/460

GP10A

Ball

1LE21012AA114EA3

689

GPA1

9

88.5

96

15

1800

254T

575

GP10A

Ball

1LE21012BB113AA3

956

GPA1

15.2

91

166

✔

7.5

3600

213TC

575

GP10A

Ball

1LE21012AA113EA3

689

GPA1

7.2

88.5

96

20

3600

256T

208-230/460

GP10A

Ball

1LE21012BA214AA3

1211

GPA1

23.5

90.2

179

✔

7.5

1800

213TC

208-230/460

GP10A

Ball

1LE21012AB114EA3

670

GPA1

9.5

89.5

102

20

3600

256T

575

GP10A

Ball

1LE21012BA213AA3

1211

GPA1

18.8

90.2

179

✔

7.5

1800

213TC

575

GP10A

Ball

1LE21012AB113EA3

670

GPA1

7.6

89.5

102

20

1800

256T

208-230/460

GP10A

Ball

1LE21012BB214AA3

1150

GPA1

25

91

185

✔

7.5

1200

254TC

208-230/460

GP10A

Ball

1LE21012BC114EA3

1119

GPA1

10.5

89.5

163

20

1800

256T

575

GP10A

Ball

1LE21012BB213AA3

1150

GPA1

20

91

185

✔

7.5

1200

254TC

575

GP10A

Ball

1LE21012BC113EA3

1119

GPA1

8.4

89.5

163

7.5

900

256TC

208-230/460

GP10A

Ball

1LE21012BD214EA3

1531

GPA1

13

87.5

189

✔

7.5

900

256TC

575

GP10A

Ball

1LE21012BD213EA3

1531

GPA1

10.4

87.5

189

10

3600

215TC

208-230/460

GP10A

Ball

1LE21012AA214EA3

797

GPA1

11.5

89.5

113

10

3600

215TC

575

GP10A

Ball

1LE21012AA213EA3

797

GPA1

9.2

89.5

113

C-Face, Horizontal, Foot Mounted 1

3600

143TC

208-230/460

GP10A

Ball

1LE21011AA114EA3

326

GPA1

1.4

80

32

1

3600

143TC

575

GP10A

Ball

1LE21011AA113EA3

326

GPA1

1.12

80

32

1

1800

143TC

208-230/460

GP10A

Ball

1LE21011AB214EA3

326

GPA1

1.5

82.5

34

1

1800

143TC

575

GP10A

Ball

1LE21011AB213EA3

326

GPA1

1.2

82.5

34

1

1200

145TC

208-230/460

GP10A

Ball

1LE21011AC314EA3

391

GPA1

1.6

80

35

1

1200

145TC

575

GP10A

Ball

1LE21011AC313EA3

391

GPA1

1.28

80

35

1

900

182TC

208-230/460

GP10A

Ball

1LE21011CD114EA3

604

GPA1

2.1

81.5

57

1

900

182TC

575

GP10A

Ball

1LE21011CD113EA3

604

GPA1

1.64

81.5

57

1.5

3600

143TC

208-230/460

GP10A

Ball

1LE21011AA214EA3

332

GPA1

2

82.5

33

3600

143TC

575

GP10A

Ball

1LE21011AA213EA3

332

GPA1

1.6

82.5

33

1800

145TC

208-230/460

GP10A

Ball

1LE21011AB314EA3

353

GPA1

2.2

84

38

1.5

1800

145TC

575

GP10A

Ball

1LE21011AB313EA3

353

GPA1

1.76

84

38

1.5

1200

182TC

208-230/460

GP10A

Ball

1LE21011CC114EA3

439

GPA1

2.4

85.5

54

1.5

1200

182TC

575

GP10A

Ball

1LE21011CC113EA3

439

GPA1

1.92

85.5

54

1.5

900

184TC

208-230/460

GP10A

Ball

1LE21011CD314EA3

648

GPA1

3

82.5

71

1.5

900

184TC

575

GP10A

Ball

1LE21011CD313EA3

648

GPA1

2.4

82.5

71

3600

145TC

208-230/460

GP10A

Ball

1LE21011AA314EA3

377

GPA1

2.6

84

35

3600

145TC

575

GP10A

Ball

1LE21011AA313EA3

377

GPA1

2.08

84

35

2

1800

145TC

208-230/460

GP10A

Ball

1LE21011AB414EA3

378

GPA1

3

84

40

2

1800

145TC

575

GP10A

Ball

1LE21011AB413EA3

378

GPA1

2.4

84

40

2

1200

184TC

208-230/460

GP10A

Ball

1LE21011CC314EA3

476

GPA1

3.1

86.5

65

2

1200

184TC

575

GP10A

Ball

1LE21011CC313EA3

476

GPA1

2.48

86.5

65

900

213TC

208-230/460

GP10A

Ball

1LE21012AD114EA3

733

GPA1

3.3

84

75

900

213TC

575

GP10A

Ball

1LE21012AD113EA3

733

GPA1

2.64

84

75

3

3600

182TC

208-230/460

GP10A

Ball

1LE21011CA114EA3

439

GPA1

3.7

85.5

56

3

3600

182TC

575

GP10A

Ball

1LE21011CA113EA3

439

GPA1

2.96

85.5

56

3

1800

182TC

208-230/460

GP10A

Ball

1LE21011CB114EA3

451

GPA1

4

87.5

59

3

1800

182TC

575

GP10A

Ball

1LE21011CB113EA3

451

GPA1

3.2

87.5

59

1200

213TC

208-230/460

GP10A

Ball

1LE21012AC114EA3

589

GPA1

4

87.5

85

1200

213TC

575

GP10A

Ball

1LE21012AC113EA3

589

GPA1

3.36

87.5

85

3

900

215TC

208-230/460

GP10A

Ball

1LE21012AD214EA3

1015

GPA1

4.8

85.5

89

3

900

215TC

575

GP10A

Ball

1LE21012AD213EA3

1015

GPA1

3.84

85.5

89

2007 Low Voltage AC Motors Selection and Pricing Guide

208-230/460

GP10A

Ball

1LE21012AB214EA3

797

GPA1

12.5

89.5

114

215TC

575

GP10A

Ball

1LE21012AB213EA3

797

GPA1

10

89.5

114

10

1200

256TC

208-230/460

GP10A

Ball

1LE21012BC214EA3

1296

GPA1

13.5

89.5

175

✔

10

1200

256TC

575

GP10A

Ball

1LE21012BC213EA3

1296

GPA1

10.8

89.5

175

15

3600

254TC

208-230/460

GP10A

Ball

1LE21012BA114EA3

1088

GPA1

18

90.2

168

✔

15

3600

254TC

575

GP10A

Ball

1LE21012BA113EA3

1088

GPA1

14.4

90.2

168

15

1800

254TC

208-230/460

GP10A

Ball

1LE21012BB114EA3

1064

GPA1

19

91

166

✔

15

1800

254TC

575

GP10A

Ball

1LE21012BB113EA3

1064

GPA1

15.2

91

166

✔ ✔

20

3600

256TC

208-230/460

GP10A

Ball

1LE21012BA214EA3

1320

GPA1

23.5

90.2

179

20

3600

256TC

575

GP10A

Ball

1LE21012BA213EA3

1320

GPA1

18.8

90.2

179

20

1800

256TC

208-230/460

GP10A

Ball

1LE21012BB214EA3

1259

GPA1

25

91

185

20

1800

256TC

575

GP10A

Ball

1LE21012BB213EA3

1259

GPA1

20

91

185

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

C-Face, Horizontal, Footless ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-6

215TC

1800

✔

1

3600

143TC

208-230/460

GP10A

Ball

1LE21011AA114GA3

341

GPA1

1.4

80

32

1

3600

143TC

575

GP10A

Ball

1LE21011AA113GA3

341

GPA1

1.12

80

32

1

1800

143TC

208-230/460

GP10A

Ball

1LE21011AB214GA3

341

GPA1

1.5

82.5

34

1

1800

143TC

575

GP10A

Ball

1LE21011AB213GA3

341

GPA1

1.2

82.5

34

1

1200

145TC

208-230/460

GP10A

Ball

1LE21011AC314GA3

407

GPA1

1.6

80

35

1

1200

145TC

575

GP10A

Ball

1LE21011AC313GA3

407

GPA1

1.28

80

35

1

900

182TC

208-230/460

GP10A

Ball

1LE21011CD114GA3

630

GPA1

2.1

81.5

57

1

900

182TC

575

GP10A

Ball

1LE21011CD113GA3

630

GPA1

1.64

81.5

57

1.5

3600

143TC

208-230/460

GP10A

Ball

1LE21011AA214GA3

348

GPA1

2

82.5

33

1.5

3600

143TC

575

GP10A

Ball

1LE21011AA213GA3

348

GPA1

1.6

82.5

33

1.5

1800

145TC

208-230/460

GP10A

Ball

1LE21011AB314GA3

368

GPA1

2.2

84

38

1.5

1800

145TC

575

GP10A

Ball

1LE21011AB313GA3

368

GPA1

1.76

84

38

1.5

1200

182TC

208-230/460

GP10A

Ball

1LE21011CC114GA3

464

GPA1

2.4

85.5

54

1.5

1200

182TC

575

GP10A

Ball

1LE21011CC113GA3

464

GPA1

1.92

85.5

54

1.5

900

184TC

208-230/460

GP10A

Ball

1LE21011CD314GA3

674

GPA1

3

82.5

71

1.5

900

184TC

575

GP10A

Ball

1LE21011CD313GA3

674

GPA1

2.4

82.5

71

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-7

NEMA PREMIUM Severe Duty

3 3

1800

10

✔

NEMA PREMIUM General Purpose

2 2

10

✔

HIGH EFFICIENT P-Base Vertical

2 2

✔

✔

HIGH EFFICIENT Definite Purpose

1.5 1.5

✔

✔

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

GP10A (Cast Aluminum Frame)

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

GP10A (Cast Aluminum Frame)

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Voltage

Type

Part Number

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model ✔

C-Face, Horizontal, Footless - continued 2

3600

145TC

208-230/460

GP10A

Ball

1LE21011AA314GA3

393

GPA1

2.6

84

35

2

3600

145TC

575

GP10A

Ball

1LE21011AA313GA3

393

GPA1

2.08

84

35

2

1800

145TC

208-230/460

GP10A

Ball

1LE21011AB414GA3

393

GPA1

3

84

40

2

1800

145TC

575

GP10A

Ball

1LE21011AB413GA3

393

GPA1

2.4

84

40

2

1200

184TC

208-230/460

GP10A

Ball

1LE21011CC314GA3

502

GPA1

3.1

86.5

65

2

1200

184TC

575

GP10A

Ball

1LE21011CC313GA3

502

GPA1

2.48

86.5

65

2

900

213TC

208-230/460

GP10A

Ball

1LE21012AD114GA3

759

GPA1

3.3

84

75

2

900

213TC

575

GP10A

Ball

1LE21012AD113GA3

759

GPA1

2.64

84

75

3

3600

182TC

208-230/460

GP10A

Ball

1LE21011CA114GA3

464

GPA1

3.7

85.5

56

3

3600

182TC

575

GP10A

Ball

1LE21011CA113GA3

464

GPA1

2.96

85.5

56

3

1800

182TC

208-230/460

GP10A

Ball

1LE21011CB114GA3

476

GPA1

4

87.5

59

3

1800

182TC

575

GP10A

Ball

1LE21011CB113GA3

476

GPA1

3.2

87.5

59

3

1200

213TC

208-230/460

GP10A

Ball

1LE21012AC114GA3

614

GPA1

4

87.5

85

3

1200

213TC

575

GP10A

Ball

1LE21012AC113GA3

614

GPA1

3.36

87.5

85

3

900

215TC

208-230/460

GP10A

Ball

1LE21012AD214GA3

1040

GPA1

4.8

85.5

89

3

900

215TC

575

GP10A

Ball

1LE21012AD213GA3

1040

GPA1

3.84

85.5

89

5

3600

184TC

208-230/460

GP10A

Ball

1LE21011CA314GA3

572

GPA1

6.2

87.5

62

5

3600

184TC

575

GP10A

Ball

1LE21011CA313GA3

572

GPA1

4.96

87.5

62

5

1800

184TC

208-230/460

GP10A

Ball

1LE21011CB314GA3

528

GPA1

6.7

87.5

66

5

1800

184TC

575

GP10A

Ball

1LE21011CB313GA3

528

GPA1

5.36

87.5

66

5

1200

215TC

208-230/460

GP10A

Ball

1LE21012AC214GA3

862

GPA1

6.8

87.5

100

5

1200

215TC

575

GP10A

Ball

1LE21012AC213GA3

862

GPA1

5.44

87.5

100

254TC

208-230/460

GP10A

Ball

1LE21012BD114GA3

1510

GPA1

8.8

86.5

157

900

254TC

575

GP10A

Ball

1LE21012BD113GA3

1510

GPA1

7.04

86.5

157

7.5

3600

213TC

208-230/460

GP10A

Ball

1LE21012AA114GA3

714

GPA1

9

88.5

96

7.5

3600

213TC

575

GP10A

Ball

1LE21012AA113GA3

714

GPA1

7.2

88.5

96

7.5

1800

213TC

208-230/460

GP10A

Ball

1LE21012AB114GA3

695

GPA1

9.5

89.5

102

7.5

1800

213TC

575

GP10A

Ball

1LE21012AB113GA3

695

GPA1

7.6

89.5

102

7.5

1200

254TC

208-230/460

GP10A

Ball

1LE21012BC114GA3

1157

GPA1

10.5

89.5

163

7.5

1200

254TC

575

GP10A

Ball

1LE21012BC113GA3

1157

GPA1

8.4

89.5

163

7.5

900

256TC

208-230/460

GP10A

Ball

1LE21012BD214GA3

1570

GPA1

13

87.5

189

7.5

900

256TC

575

GP10A

Ball

1LE21012BD213GA3

1570

GPA1

10.4

87.5

189

10

3600

215TC

208-230/460

GP10A

Ball

1LE21012AA214GA3

822

GPA1

11.5

89.5

113

10

3600

215TC

575

GP10A

Ball

1LE21012AA213GA3

822

GPA1

9.2

89.5

113

10

1800

215TC

208-230/460

GP10A

Ball

1LE21012AB214GA3

822

GPA1

12.5

89.5

114

10

1800

215TC

575

GP10A

Ball

1LE21012AB213GA3

822

GPA1

10

89.5

114

10

1200

256TC

208-230/460

GP10A

Ball

1LE21012BC214GA3

1335

GPA1

13.5

89.5

175

10

1200

256TC

575

GP10A

Ball

1LE21012BC213GA3

1335

GPA1

10.8

89.5

175

3600

254TC

208-230/460

GP10A

Ball

1LE21012BA114GA3

1126

GPA1

18

90.2

168

15

3600

254TC

575

GP10A

Ball

1LE21012BA113GA3

1126

GPA1

14.4

90.2

168

1800

254TC

208-230/460

GP10A

Ball

1LE21012BB114GA3

1103

GPA1

19

91

166

15

1800

254TC

575

GP10A

Ball

1LE21012BB113GA3

1103

GPA1

15.2

91

166

20

3600

256TC

208-230/460

GP10A

Ball

1LE21012BA214GA3

1358

GPA1

23.5

90.2

179

20

3600

256TC

575

GP10A

Ball

1LE21012BA213GA3

1358

GPA1

18.8

90.2

179

20

1800

256TC

208-230/460

GP10A

Ball

1LE21012BB214GA3

1297

GPA1

25

91

185

20

1800

256TC

575

GP10A

Ball

1LE21012BB213GA3

1297

GPA1

20

91

185

Frame & End Shields - Cast iron construction for exceptional structural integrity & corrosion resistance equipped with integrally cast feet and condensation drain holes. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Polycarbonate fan covers are provided on all frame sizes.

•

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

• • •

Rotor - A unique offset rotor bar design provides improved efficiency. Large cross section bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

✔ ✔

Bearings - Lubricated for life, oversized, complete with external bearing protection. Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Oversized Conduit Box - Cast aluminum construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - Cast iron construction, structural foam fan and fan cover, zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. Modifiable - Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Specifications table begins on the next page

✔ ✔ ✔ ✔ ✔ ✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-8

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-9

NEMA PREMIUM Severe Duty

15

Features for Long Life

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31 making all motors suitable for operation with variable frequency drives.

✔ ✔

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800, 1200 or 900 RPM 3 phase, 60 Hz; 208-230/460 and 575 volt operation Meets or exceeds EPAct efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 143T through 256T frame

NEMA PREMIUM General Purpose

15

• • • •

HIGH EFFICIENT P-Base Vertical

900

5

✔

Performance Specifications

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Definite Purpose

5

✔

The new GP10 series of TEFC motors are ideal for material handling, pump, fan, compressor and other general purpose industrial applications.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Frame

Multiplier Symbol

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RPM

List Price $

GP10 (Cast Iron Frame)

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

GP10A (Cast Aluminum Frame) DE Bearing

Introduction

General Purpose - TEFC Motors

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

HP

RPM

Frame

Voltage

Type

Stock/Modifiable DE Bearing

Part Number

List Multiplier FL Price $ Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

1

3600

143T

208-230/460

GP10

Ball

1LE22011AA114AA3

300

GP1

1.4

80

51

✔

10

3600

215T

208-230/460

GP10

Ball

1LE22012AA214AA3

801

GP1

11.5

89.5

150

✔

1

3600

143T

575

GP10

Ball

1LE22011AA113AA3

300

GP1

1.12

80

51

✔

10

3600

215T

575

GP10

Ball

1LE22012AA213AA3

801

GP1

9.2

89.5

150

✔

1

1800

143T

208-230/460

GP10

Ball

1LE22011AB214AA3

300

GP1

1.5

82.5

53

✔

10

1800

215T

208-230/460

GP10

Ball

1LE22012AB214AA3

801

GP1

12.5

89.5

151

✔

1

1800

143T

575

GP10

Ball

1LE22011AB213AA3

300

GP1

1.2

82.5

53

✔

10

1800

215T

575

GP10

Ball

1LE22012AB213AA3

801

GP1

10

89.5

151

✔

1

1200

145T

208-230/460

GP10

Ball

1LE22011AC314AA3

374

GP1

1.6

80

54

✔

10

1200

256T

208-230/460

GP10

Ball

1LE22012BC214AA3

1334

GP1

13.5

89.5

236

✔

1

1200

145T

575

GP10

Ball

1LE22011AC313AA3

374

GP1

1.28

80

54

✔

10

1200

256T

575

GP10

Ball

1LE22012BC213AA3

1334

GP1

10.8

89.5

236

✔

1

900

182T

208-230/460

GP10

Ball

1LE22011CD114AA3

585

GP1

2.1

81.5

86

✔

15

3600

254T

208-230/460

GP10

Ball

1LE22012BA114AA3

1099

GP1

18

90.2

228

✔

1

900

182T

575

GP10

Ball

1LE22011CD113AA3

585

GP1

1.64

81.5

86

✔

15

3600

254T

575

GP10

Ball

1LE22012BA113AA3

1099

GP1

14.4

90.2

228

✔

1.5

3600

143T

208-230/460

GP10

Ball

1LE22011AA214AA3

308

GP1

2

82.5

53

✔

15

1800

254T

208-230/460

GP10

Ball

1LE22012BB114AA3

1073

GP1

19

91

227

✔

1.5

3600

143T

575

GP10

Ball

1LE22011AA213AA3

308

GP1

1.6

82.5

53

✔

15

1800

254T

575

GP10

Ball

1LE22012BB113AA3

1073

GP1

15.2

91

227

✔

1.5

1800

145T

208-230/460

GP10

Ball

1LE22011AB314AA3

331

GP1

2.2

84

58

✔

20

3600

256T

208-230/460

GP10

Ball

1LE22012BA214AA3

1360

GP1

23.5

90.2

241

✔

1.5

1800

145T

575

GP10

Ball

1LE22011AB313AA3

331

GP1

1.76

84

58

✔

20

3600

256T

575

GP10

Ball

1LE22012BA213AA3

1360

GP1

18.8

90.2

241

✔

1.5

1200

182T

208-230/460

GP10

Ball

1LE22011CC114AA3

399

GP1

2.4

85.5

83

✔

20

1800

256T

208-230/460

GP10

Ball

1LE22012BB214AA3

1292

GP1

25

91

246

✔

1.5

1200

182T

575

GP10

Ball

1LE22011CC113AA3

399

GP1

1.92

85.5

83

✔

20

1800

256T

575

GP10

Ball

1LE22012BB213AA3

1292

GP1

20

91

246

✔

1.5

900

184T

208-230/460

GP10

Ball

1LE22011CD314AA3

634

GP1

3

82.5

99

✔

1.5

900

184T

575

GP10

Ball

1LE22011CD313AA3

634

GP1

2.4

82.5

99

✔

1

3600

143TC

208-230/460

GP10

Ball

1LE22011AA114EA3

353

GP1

1.4

80

51

✔

2

3600

145T

208-230/460

GP10

Ball

1LE22011AA314AA3

358

GP1

2.6

84

54

✔

1

3600

143TC

575

GP10

Ball

1LE22011AA113EA3

353

GP1

1.12

80

51

2

3600

145T

575

GP10

Ball

1LE22011AA313AA3

358

GP1

2.08

84

54

✔

1

1800

143TC

208-230/460

GP10

Ball

1LE22011AB214EA3

353

GP1

1.5

82.5

53

2

1800

145T

208-230/460

GP10

Ball

1LE22011AB414AA3

359

GP1

3

84

59

✔

1

1800

143TC

575

GP10

Ball

1LE22011AB213EA3

353

GP1

1.2

82.5

53

2

1800

145T

575

GP10

Ball

1LE22011AB413AA3

359

GP1

2.4

84

59

✔

1

1200

145TC

208-230/460

GP10

Ball

1LE22011AC314EA3

427

GP1

1.6

80

54

2

1200

184T

208-230/460

GP10

Ball

1LE22011CC314AA3

441

GP1

3.1

86.5

94

✔

1

1200

145TC

575

GP10

Ball

1LE22011AC313EA3

427

GP1

1.28

80

54

2

1200

184T

575

GP10

Ball

1LE22011CC313AA3

441

GP1

2.48

86.5

94

✔

1

900

182TC

208-230/460

GP10

Ball

1LE22011CD114EA3

661

GP1

2.1

81.5

86

2

900

213T

208-230/460

GP10

Ball

1LE22012AD114AA3

730

GP1

3.3

84

123

✔

1

900

182TC

575

GP10

Ball

1LE22011CD113EA3

661

GP1

1.64

81.5

86

2

900

213T

575

GP10

Ball

1LE22012AD113AA3

730

GP1

2.64

84

123

✔

1.5

3600

143TC

208-230/460

GP10

Ball

1LE22011AA214EA3

361

GP1

2

82.5

53

3

3600

182T

208-230/460

GP10

Ball

1LE22011CA114AA3

399

GP1

3.7

85.5

85

✔

1.5

3600

143TC

575

GP10

Ball

1LE22011AA213EA3

361

GP1

1.6

82.5

53

3

3600

182T

575

GP10

Ball

1LE22011CA113AA3

399

GP1

2.96

85.5

85

✔

1.5

1800

145TC

208-230/460

GP10

Ball

1LE22011AB314EA3

384

GP1

2.2

84

58

3

1800

182T

208-230/460

GP10

Ball

1LE22011CB114AA3

413

GP1

4

87.5

88

✔

1.5

1800

145TC

575

GP10

Ball

1LE22011AB313EA3

384

GP1

1.76

84

58

3

1800

182T

575

GP10

Ball

1LE22011CB113AA3

413

GP1

3.2

87.5

88

✔

1.5

1200

182TC

208-230/460

GP10

Ball

1LE22011CC114EA3

475

GP1

2.4

85.5

83

3

1200

213T

208-230/460

GP10

Ball

1LE22012AC114AA3

567

GP1

4

87.5

143

✔

1.5

1200

182TC

575

GP10

Ball

1LE22011CC113EA3

475

GP1

1.92

85.5

83

3

1200

213T

575

GP10

Ball

1LE22012AC113AA3

567

GP1

3.36

87.5

143

✔

1.5

900

184TC

208-230/460

GP10

Ball

1LE22011CD314EA3

710

GP1

3

82.5

99

3

900

215T

208-230/460

GP10

Ball

1LE22012AD214AA3

1046

GP1

4.8

85.5

138

✔

1.5

900

184TC

575

GP10

Ball

1LE22011CD313EA3

710

GP1

2.4

82.5

99

3

900

215T

575

GP10

Ball

1LE22012AD213AA3

1046

GP1

3.84

85.5

138

✔

2

3600

145TC

208-230/460

GP10

Ball

1LE22011AA314EA3

411

GP1

2.6

84

54

5

3600

184T

208-230/460

GP10

Ball

1LE22011CA314AA3

520

GP1

6.2

87.5

91

✔

2

3600

145TC

575

GP10

Ball

1LE22011AA313EA3

411

GP1

2.08

84

54

5

3600

184T

575

GP10

Ball

1LE22011CA313AA3

520

GP1

4.96

87.5

91

✔

2

1800

145TC

208-230/460

GP10

Ball

1LE22011AB414EA3

412

GP1

3

84

59

5

1800

184T

208-230/460

GP10

Ball

1LE22011CB314AA3

470

GP1

6.7

87.5

94

✔

2

1800

145TC

575

GP10

Ball

1LE22011AB413EA3

412

GP1

2.4

84

59

5

1800

184T

575

GP10

Ball

1LE22011CB313AA3

470

GP1

5.36

87.5

94

✔

2

1200

184TC

208-230/460

GP10

Ball

1LE22011CC314EA3

517

GP1

3.1

86.5

94

5

1200

215T

208-230/460

GP10

Ball

1LE22012AC214AA3

845

GP1

6.8

87.5

151

✔

2

1200

184TC

575

GP10

Ball

1LE22011CC313EA3

517

GP1

2.48

86.5

94

5

1200

215T

575

GP10

Ball

1LE22012AC213AA3

845

GP1

5.44

87.5

151

✔

2

900

213TC

208-230/460

GP10

Ball

1LE22012AD114EA3

806

GP1

3.3

84

123

5

900

254T

208-230/460

GP10

Ball

1LE22012BD114AA3

1530

GP1

8.8

86.5

218

✔

2

900

213TC

575

GP10

Ball

1LE22012AD113EA3

806

GP1

2.64

84

123

C-Face, Horizontal, Foot Mounted

GP10

Ball

1LE22012BD113AA3

1530

GP1

7.04

86.5

218

✔

3

3600

182TC

208-230/460

GP10

Ball

1LE22011CA114EA3

475

GP1

3.7

85.5

85

208-230/460

GP10

Ball

1LE22012AA114AA3

679

GP1

9

88.5

137

✔

3

3600

182TC

575

GP10

Ball

1LE22011CA113EA3

475

GP1

2.96

85.5

85

7.5

3600

213T

575

GP10

Ball

1LE22012AA113AA3

679

GP1

7.2

88.5

137

✔

3

1800

182TC

208-230/460

GP10

Ball

1LE22011CB114EA3

489

GP1

4

87.5

88

7.5

1800

213T

208-230/460

GP10

Ball

1LE22012AB114AA3

658

GP1

9.5

89.5

143

✔

3

1800

182TC

575

GP10

Ball

1LE22011CB113EA3

489

GP1

3.2

87.5

88

7.5

1800

213T

575

GP10

Ball

1LE22012AB113AA3

658

GP1

7.6

89.5

143

✔

3

1200

213TC

208-230/460

GP10

Ball

1LE22012AC114EA3

643

GP1

4

87.5

143

7.5

1200

254T

208-230/460

GP10

Ball

1LE22012BC114AA3

1134

GP1

10.5

89.5

224

✔

3

1200

213TC

575

GP10

Ball

1LE22012AC113EA3

643

GP1

3.36

87.5

143

7.5

1200

254T

575

GP10

Ball

1LE22012BC113AA3

1134

GP1

8.4

89.5

224

✔

3

900

215TC

208-230/460

GP10

Ball

1LE22012AD214EA3

1122

GP1

4.8

85.5

138

7.5

900

256T

208-230/460

GP10

Ball

1LE22012BD214AA3

1597

GP1

13

87.5

250

✔

3

900

215TC

575

GP10

Ball

1LE22012AD213EA3

1122

GP1

3.84

85.5

138

7.5

900

256T

575

GP10

Ball

1LE22012BD213AA3

1597

GP1

10.4

87.5

250

✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-10

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-11

NEMA PREMIUM Severe Duty

575

213T

✔

NEMA PREMIUM General Purpose

254T

✔

HIGH EFFICIENT P-Base Vertical

900 3600

✔

HIGH EFFICIENT Definite Purpose

5 7.5

✔

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

GP10 (Cast Iron Frame)

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

GP10 (Cast Iron Frame)

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL FL Nom. Amps* Eff. (%)

Weight (lbs.)

Stock Model

5

3600

184TC

208-230/460

GP10

Ball

1LE22011CA314EA3

596

GP1

6.2

87.5

91

5

3600

184TC

575

GP10

Ball

1LE22011CA313EA3

596

GP1

4.96

87.5

91

5

1800

184TC

208-230/460

GP10

Ball

1LE22011CB314EA3

546

GP1

6.7

87.5

94

5

1800

184TC

575

GP10

Ball

1LE22011CB313EA3

546

GP1

5.36

87.5

94

5

1200

215TC

208-230/460

GP10

Ball

1LE22012AC214EA3

921

GP1

6.8

87.5

151

5

1200

215TC

575

GP10

Ball

1LE22012AC213EA3

921

GP1

5.44

87.5

151

5

900

254TC

208-230/460

GP10

Ball

1LE22012BD114EA3

1629

GP1

8.8

86.5

218

5

900

254TC

575

GP10

Ball

1LE22012BD113EA3

1629

GP1

7.04

86.5

218

7.5

3600

213TC

208-230/460

GP10

Ball

1LE22012AA114EA3

755

GP1

9

88.5

137

7.5

3600

213TC

575

GP10

Ball

1LE22012AA113EA3

755

GP1

7.2

88.5

137

7.5

1800

213TC

208-230/460

GP10

Ball

1LE22012AB114EA3

734

GP1

9.5

89.5

143

7.5

1800

213TC

575

GP10

Ball

1LE22012AB113EA3

734

GP1

7.6

89.5

143

7.5

1200

254TC

208-230/460

GP10

Ball

1LE22012BC114EA3

1233

GP1

10.5

89.5

224

7.5

1200

254TC

575

GP10

Ball

1LE22012BC113EA3

1233

GP1

8.4

89.5

224

7.5

900

256TC

208-230/460

GP10

Ball

1LE22012BD214EA3

1696

GP1

87.5

250

7.5

900

256TC

575

GP10

Ball

1LE22012BD213EA3

1696

GP1

10.4

87.5

250

10

3600

215TC

208-230/460

GP10

Ball

1LE22012AA214EA3

877

GP1

11.5

89.5

150

10

3600

215TC

575

GP10

Ball

1LE22012AA213EA3

877

GP1

9.2

89.5

150

13

10

1800

215TC

208-230/460

GP10

Ball

1LE22012AB214EA3

877

GP1

12.5

89.5

151

10

1800

215TC

575

GP10

Ball

1LE22012AB213EA3

877

GP1

10

89.5

151

10

1200

256TC

208-230/460

GP10

Ball

1LE22012BC214EA3

1433

GP1

13.5

89.5

236

10

1200

256TC

575

GP10

Ball

1LE22012BC213EA3

1433

GP1

10.8

89.5

236

15

3600

254TC

208-230/460

GP10

Ball

1LE22012BA114EA3

1198

GP1

18

90.2

228

15

3600

254TC

575

GP10

Ball

1LE22012BA113EA3

1198

GP1

14.4

90.2

228

1800

254TC

208-230/460

GP10

Ball

1LE22012BB114EA3

1172

GP1

19

91

227

1800

254TC

575

GP10

Ball

1LE22012BB113EA3

1172

GP1

15.2

91

227

20

3600

256TC

208-230/460

GP10

Ball

1LE22012BA214EA3

1459

GP1

23.5

90.2

241

20

3600

256TC

575

GP10

Ball

1LE22012BA213EA3

1459

GP1

18.8

90.2

241

20

1800

256TC

208-230/460

GP10

Ball

1LE22012BB214EA3

1391

GP1

25

91

246

1800

256TC

575

Frame

Voltage

Type

Part Number

List Multiplier FL Price $ Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Ball

1LE22012BB213EA3

1391

GP1

20

GP10

Ball

1LE22011AA114GA3

367

GP1

1.4

91

246

80

51

✔ ✔ ✔ ✔ ✔ ✔

2

3600

145TC

208-230/460

GP10

Ball

1LE22011AA314GA3

425

GP1

2.6

84

54

2

3600

145TC

575

GP10

Ball

1LE22011AA313GA3

425

GP1

2.08

84

54

2

1800

145TC

208-230/460

GP10

Ball

1LE22011AB414GA3

426

GP1

3

84

59

2

1800

145TC

575

GP10

Ball

1LE22011AB413GA3

426

GP1

2.4

84

59

2

1200

184TC

208-230/460

GP10

Ball

1LE22011CC314GA3

540

GP1

3.1

86.5

94

2

1200

184TC

575

GP10

Ball

1LE22011CC313GA3

540

GP1

2.48

86.5

94

2

900

213TC

208-230/460

GP10

Ball

1LE22012AD114GA3

829

GP1

3.3

84

123

2

900

213TC

575

GP10

Ball

1LE22012AD113GA3

829

GP1

2.64

84

123

3

3600

182TC

208-230/460

GP10

Ball

1LE22011CA114GA3

498

GP1

3.7

85.5

85

3

3600

182TC

575

GP10

Ball

1LE22011CA113GA3

498

GP1

2.96

85.5

85

3

1800

182TC

208-230/460

GP10

Ball

1LE22011CB114GA3

512

GP1

4

87.5

88

3

1800

182TC

575

GP10

Ball

1LE22011CB113GA3

512

GP1

3.2

87.5

88

3

1200

213TC

208-230/460

GP10

Ball

1LE22012AC114GA3

666

GP1

4

87.5

143

3

1200

213TC

575

GP10

Ball

1LE22012AC113GA3

666

GP1

3.36

87.5

143

✔

3

900

215TC

208-230/460

GP10

Ball

1LE22012AD214GA3

1145

GP1

4.8

85.5

138

3

900

215TC

575

GP10

Ball

1LE22012AD213GA3

1145

GP1

3.84

85.5

138

✔

5

3600

184TC

208-230/460

GP10

Ball

1LE22011CA314GA3

619

GP1

6.2

87.5

91

5

3600

184TC

575

GP10

Ball

1LE22011CA313GA3

619

GP1

4.96

87.5

91

5

1800

184TC

208-230/460

GP10

Ball

1LE22011CB314GA3

569

GP1

6.7

87.5

94

5

1800

184TC

575

GP10

Ball

1LE22011CB313GA3

569

GP1

5.36

87.5

94

✔ ✔ ✔ ✔ ✔ ✔

5

1200

215TC

208-230/460

GP10

Ball

1LE22012AC214GA3

944

GP1

6.8

87.5

151

5

1200

215TC

575

GP10

Ball

1LE22012AC213GA3

944

GP1

5.44

87.5

151

5

900

254TC

208-230/460

GP10

Ball

1LE22012BD114GA3

1664

GP1

8.8

86.5

218

5

900

254TC

575

GP10

Ball

1LE22012BD113GA3

1664

GP1

7.04

86.5

218

7.5

3600

213TC

208-230/460

GP10

Ball

1LE22012AA114GA3

778

GP1

9

88.5

137

7.5

3600

213TC

575

GP10

Ball

1LE22012AA113GA3

778

GP1

7.2

88.5

137

7.5

1800

213TC

208-230/460

GP10

Ball

1LE22012AB114GA3

757

GP1

9.5

89.5

143

7.5

1800

213TC

575

GP10

Ball

1LE22012AB113GA3

757

GP1

7.6

89.5

143

7.5

1200

254TC

208-230/460

GP10

Ball

1LE22012BC114GA3

1268

GP1

10.5

89.5

224

7.5

1200

254TC

575

GP10

Ball

1LE22012BC113GA3

1268

GP1

8.4

89.5

224

7.5

900

256TC

208-230/460

GP10

Ball

1LE22012BD214GA3

1731

GP1

13

87.5

250

✔

7.5

900

256TC

575

GP10

Ball

1LE22012BD213GA3

1731

GP1

10.4

87.5

250

10

3600

215TC

208-230/460

GP10

Ball

1LE22012AA214GA3

900

GP1

11.5

89.5

150

✔

10

3600

215TC

575

GP10

Ball

1LE22012AA213GA3

900

GP1

9.2

89.5

150

10

1800

215TC

208-230/460

GP10

Ball

1LE22012AB214GA3

900

GP1

12.5

89.5

151

✔

10

1800

215TC

575

GP10

Ball

1LE22012AB213GA3

900

GP1

10

89.5

151

3600

143TC

575

GP10

Ball

1LE22011AA113GA3

367

GP1

1.12

80

51

1

1800

143TC

208-230/460

GP10

Ball

1LE22011AB214GA3

367

GP1

1.5

82.5

53

1

1800

143TC

575

GP10

Ball

1LE22011AB213GA3

367

GP1

1.2

82.5

53

1

1200

145TC

208-230/460

GP10

Ball

1LE22011AC314GA3

441

GP1

1.6

80

54

1

1200

145TC

575

GP10

Ball

1LE22011AC313GA3

441

GP1

1.28

80

54

10

1200

256TC

208-230/460

GP10

Ball

1LE22012BC214GA3

1468

GP1

13.5

89.5

236

✔

10

1200

256TC

575

GP10

Ball

1LE22012BC213GA3

1468

GP1

10.8

89.5

236

15

3600

254TC

208-230/460

GP10

Ball

1LE22012BA114GA3

1233

GP1

18

90.2

228

✔

15

3600

254TC

575

GP10

Ball

1LE22012BA113GA3

1233

GP1

14.4

90.2

228

1

900

182TC

208-230/460

GP10

Ball

1LE22011CD114GA3

684

GP1

2.1

81.5

86

1

900

182TC

575

GP10

Ball

1LE22011CD113GA3

684

GP1

1.64

81.5

86

1.5

3600

143TC

208-230/460

GP10

Ball

1LE22011AA214GA3

375

GP1

2

82.5

53

1.5

3600

143TC

575

GP10

Ball

1LE22011AA213GA3

375

GP1

1.6

82.5

53

1800

145TC

208-230/460

GP10

Ball

1LE22011AB314GA3

398

GP1

2.2

84

58

1.5

1800

145TC

575

GP10

Ball

1LE22011AB313GA3

398

GP1

1.76

84

58

1.5

1200

182TC

208-230/460

GP10

Ball

1LE22011CC114GA3

498

GP1

2.4

85.5

83

1.5

1200

182TC

575

GP10

Ball

1LE22011CC113GA3

498

GP1

1.92

85.5

83

1.5

900

184TC

208-230/460

GP10

Ball

1LE22011CD314GA3

733

GP1

3

82.5

99

1.5

900

184TC

575

GP10

Ball

1LE22011CD313GA3

733

GP1

2.4

82.5

99

✔ ✔ ✔

1800

254TC

208-230/460

GP10

Ball

1LE22012BB114GA3

1207

GP1

19

91

227

1800

254TC

575

GP10

Ball

1LE22012BB113GA3

1207

GP1

15.2

91

227

20

3600

256TC

208-230/460

GP10

Ball

1LE22012BA214GA3

1494

GP1

23.5

90.2

241

20

3600

256TC

575

GP10

Ball

1LE22012BA213GA3

1494

GP1

18.8

90.2

241

20

1800

256TC

208-230/460

GP10

Ball

1LE22012BB214GA3

1426

GP1

25

91

246

20

1800

256TC

575

GP10

Ball

1LE22012BB213GA3

1426

GP1

20

91

246

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-12

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-13

NEMA PREMIUM Severe Duty

1.5

15 15

✔

NEMA PREMIUM General Purpose

1

✔

HIGH EFFICIENT P-Base Vertical

GP10

✔

HIGH EFFICIENT Definite Purpose

15 15

20

RPM

DE Bearing

C-Face, Horizontal, Footless - continued

C-Face, Horizontal, Foot Mounted - continued

C-Face, Horizontal, Footless 1 3600 143TC 208-230/460

HP

Stock/Modifiable

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

GP10 (Cast Iron Frame)

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

GP10 (Cast Iron Frame)

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction

RGZP

HIGH EFFICIENT General Purpose

General Purpose TEFC motors are ideal for both indoor and outdoor applications and in operating atmospheres that contain moisture, dust and grit. These industry workhorses are ideal for use in material handling, pump, fan, compressor and other industrial applications.

HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

• • • •

1 to 200 HP 1.15 service factor, 40°C ambient 3600, 1800, 1200 or 900 RPM 3 phase, 60 Hz; 230/460 volt operation under 100 HP, 460 volt 100 HP and above; 575 volt available Meets or exceeds EPAct efficiency standards Class F insulation, Class B temperature rise NEMA Design B, Continuous Duty 143T through 449T frame

Features for Long Life

2007 Low Voltage AC Motors Selection and Pricing Guide

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Larger than industry standards, diagonally-split, gasketed and rotatable in 90° increments for quick and easy connections. Leads are non-wicking and are clearly and permanently marked. Aluminum construction for frames 143T to 256T, steel for frames 284T to 405T and cast iron for 444T frames and larger. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

1

3600

143T

230/460

RGZP

Ball

1LA01432FP21

286

SA-7ST

1.4

75.5

45

✔

1

3600

143T

575

RGZP

Ball

1LA01432FP51

286

SA-7ST

1.1

75.5

50

✔

1

1800

143T

230/460

RGZP

Ball

1LA01444FP21

286

SA-7ST

1.5

82.5

45

✔

1

1800

143T

575

RGZP

Ball

1LA01444FP51

286

SA-7ST

1.2

82.5

50

✔

1

1200

145T

230/460

RGZP

Ball

1LA01456FP21

356

SA-7ST

1.8

80

51

✔

1

1200

145T

575

RGZP

Ball

1LA01456FP51

356

SA-7ST

1.4

80

55

✔

1

900

182T

230/460

RGZP

Ball

1LA01828FP21

557

SA-7ST

1.9

78.5

82

✔

1.5

3600

143T

230/460

RGZP

Ball

1LA01442FP21

293

SA-7ST

2

82.5

45

✔

1.5

3600

143T

575

RGZP

Ball

1LA01442FP51

293

SA-7ST

2

82.5

50

✔

1.5

1800

145T

230/460

RGZP

Ball

1LA01454FP21

315

SA-7ST

2.2

84

55

✔

1.5

1800

145T

575

RGZP

Ball

1LA01454FP51

315

SA-7ST

1.8

84

45

✔

1.5

1200

182T

230/460

RGZP

Ball

1LA01826FP21

380

SA-7ST

2.3

85.5

77

✔

1.5

1200

182T

575

RGZP

Ball

1LA01826FP51

380

SA-7ST

1.8

85.5

85

✔

1.5

900

184T

230/460

RGZP

Ball

1LA01848FP21

604

SA-7ST

2.6

80

86

✔

2

3600

145T

230/460

RGZP

Ball

1LA01452FP21

341

SA-7ST

2.5

84

55

✔

2

3600

145T

575

RGZP

Ball

1LA01452FP51

341

SA-7ST

2

84

49

✔

2

1800

145T

230/460

RGZP

Ball

1LA01464FP21

342

SA-7ST

2.9

84

48

✔

2

1800

145T

575

RGZP

Ball

1LA01464FP51

342

SA-7ST

2.3

84

55

✔

2

1200

184T

230/460

RGZP

Ball

1LA01846FP21

420

SA-7ST

3

86.5

85

✔

2

1200

184T

575

RGZP

Ball

1LA01846FP51

420

SA-7ST

2

86.5

100

✔

2

900

213T

230/460

RGZP

Ball

1LA02138FP21

695

SA-7ST

3.3

82.5

135

✔

3

3600

182T

230/460

RGZP

Ball

1LA01822FP21

380

SA-7ST

3.7

85.5

85

✔

3

3600

182T

575

RGZP

Ball

1LA01822FP51

380

SA-7ST

3

85.5

85

✔

3

1800

182T

230/460

RGZP

Ball

1LA01824FP21

393

SA-7ST

3.9

87.5

85

✔

3

1800

182T

575

RGZP

Ball

1LA01824FP51

393

SA-7ST

3.1

87.5

85

✔

3

1200

213T

230/460

RGZP

Ball

1LA02136FP21

540

SA-7ST

4

87.5

135

✔

3

1200

213T

575

RGZP

Ball

1LA02136FP51

540

SA-7ST

3

87.5

135

✔

3

900

215T

230/460

RGZP

Ball

1LA02158FP21

996

SA-7ST

4.7

84

160

✔

5

3600

184T

230/460

RGZP

Ball

1LA01842FP21

495

SA-7ST

5.8

87.5

100

✔

5

3600

184T

575

RGZP

Ball

1LA01842FP51

495

SA-7ST

4.6

87.5

100

✔

5

1800

184T

230/460

RGZP

Ball

1LA01844FP21

448

SA-7ST

6.5

87.5

85

✔

5

1800

184T

575

RGZP

Ball

1LA01844FP51

448

SA-7ST

5.2

87.5

100

✔

5

1200

215T

230/460

RGZP

Ball

1LA02156FP21

805

SA-7ST

6.8

87.5

160

✔

5

1200

215T

575

RGZP

Ball

1LA02156FP51

805

SA-7ST

5.4

87.5

160

✔

5

900

254T

230/460

RGZP

Ball

1LA02548FP21

1457

SA-7ST

7.5

86.5

245

✔

7.5

3600

213T

230/460

RGZP

Ball

1LA02132FP21

647

SA-7ST

8.8

88.5

135

✔

7.5

3600

213T

575

RGZP

Ball

1LA02132FP51

647

SA-7ST

7

88.5

123

✔

7.5

1800

213T

230/460

RGZP

Ball

1LA02134FP21

627

SA-7ST

9.5

89.5

135

✔

7.5

1800

213T

575

RGZP

Ball

1LA02134FP51

627

SA-7ST

7.6

89.5

135

✔

7.5

1200

254T

230/460

RGZP

Ball

1LA02546FP21

1080

SA-7ST

9.8

89.5

245

✔

7.5

1200

254T

575

RGZP

Ball

1LA02546FP51

1080

SA-7ST

7.8

89.5

245

✔

10

3600

215T

230/460

RGZP

Ball

1LA02152FP21

763

SA-7ST

12

89.5

160

✔

10

3600

215T

575

RGZP

Ball

1LA02152FP51

763

SA-7ST

10

89.5

160

✔

10

1800

215T

230/460

RGZP

Ball

1LA02154FP21

763

SA-7ST

13

89.5

160

✔

10

1800

215T

575

RGZP

Ball

1LA02154FP51

763

SA-7ST

10

89.5

160

✔

10

1200

256T

230/460

RGZP

Ball

1LA02566FP21

1270

SA-7ST

13

89.5

285

✔

10

1200

256T

575

RGZP

Ball

1LA02566FP51

1270

SA-7ST

10

89.5

285

✔

* FL amps are at 460V or 575V depending on the voltage rating of motor.

2-14

Part Number

DOE#CC032A

Shaded ratings will be discontinued when present stock is depleted. Replaced by type GP10

2007 Low Voltage AC Motors Selection and Pricing Guide

2-15

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Type

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Voltage

FL Amps*

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Bearings – Greaseable, oversized single shielded with cast iron inner caps (444T–449T frames), pipe plugs on both the inlet and relief ports (143T–256T frames). Alemite grease fittings on the inlets and pipe plugs on the relief ports (284T–449T frames) for ease of routine maintenance. For added bearing protection, 284T–449T frames are equipped with a drive end shaft V-ring slinger.

Frame

Multiplier Symbol

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction (aluminum endshields 143T–256T frames) for exceptional structural integrity with condensation drain holes (143T–256T frames) or condensation T-drains (284T–449T frames). Lifting eyebolts are included for frames 213T to 449T.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Polycarbonate fan covers are provided on 143T up to 365T frames, and cast iron for frames 404T and larger.

RPM

List Price $

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

• • • •

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system is suitable for operation with variable frequency drives.

HP

DE Bearing

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Performance Specifications

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity.

Stock/Modifiable

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

RGZP

HIGH EFFICIENT General Purpose

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Voltage

Type

Part Number

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

3600

254T

230/460

RPM

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

Horizontal, Foot Mounted - continued 15

HP

DE Bearing

RGZP

Ball

1LA02542FP21

1047

SA-7ST

17

90.2

245

✔

100

3600

405TS

460

RGZP

Ball

1LA04052FP42

7115

SA-7ST

112

93.6

1300

✔

3600

405TS

575

RGZP

Ball

1LA04052FP52

7115

SA-7ST

90

93.6

1300

✔

15

3600

254T

575

RGZP

Ball

1LA02542FP51

1047

SA-7ST

14

90.2

245

✔

100

15

1800

254T

230/460

RGZP

Ball

1LA02544FP21

1022

SA-7ST

19

91

245

✔

100

1800

405T

460

RGZP

Ball

1LA04054FP41

6725

SA-7ST

114

94.5

1300

✔

15

1800

254T

575

RGZP

Ball

1LA02544FP51

1022

SA-7ST

15

91

245

✔

100

1800

405TS

460

RGZP

Ball

1LA04054FP42

6725

SA-7ST

114

94.5

1300

✔

15

1200

284T

230/460

RGZP

Ball

1LA02846FP21

1730

SA-7ST

20

90.2

375

✔

100

1800

405T

575

RGZP

Ball

1LA04054FP51

6725

SA-7ST

91

94.5

1300

✔

15

1200

284T

575

RGZP

Ball

1LA02846FP51

1730

SA-7ST

16

90.2

375

✔

100

1200

444T

460

RGZP

Roller

1LA04446FP41

9250

SA-7ST

117

94.1

1625

✔

20

3600

256T

230/460

RGZP

Ball

1LA02562FP21

1295

SA-7ST

23

90.2

285

✔

100

1200

444TS

460

RGZP

Ball

1LA04446FP42

9250

SA-7ST

117

94.1

1625

✔

20

3600

256T

575

RGZP

Ball

1LA02562FP51

1295

SA-7ST

18

90.2

285

✔

100

1200

444T

575

RGZP

Roller

1LA04446FP51

9250

SA-7ST

94

94.1

1625

✔

20

1800

256T

230/460

RGZP

Ball

1LA02564FP21

1230

SA-7ST

26

91

285

✔

125

3600

444TS

460

RGZP

Ball

1LA04442FP42

9732

SA-7ST

138

94.5

1552

✔

20

1800

256T

575

RGZP

Ball

1LA02564FP51

1230

SA-7ST

21

91

285

✔

125

3600

444TS

575

RGZP

Ball

1LA04442FP52

9732

SA-7ST

110

94.5

1552

✔

20

1200

286T

230/460

RGZP

Ball

1LA02866FP21

2070

SA-7ST

26

90.2

430

✔

125

1800

444T

460

RGZP

Roller

1LA04444FP41

9060

SA-7ST

145

94.5

1625

✔

20

1200

286T

575

RGZP

Ball

1LA02866FP51

2070

SA-7ST

21

90.2

430

✔

125

1800

B444T

460

RGZP

Ball

1LA04444FP4N

9060

SA-7ST

145

94.5

1625

✔

25

3600

284TS

230/460

RGZP

Ball

1LA02842FP22

1574

SA-7ST

29

91

375

✔

125

1800

444TS

460

RGZP

Ball

1LA04444FP42

9060

SA-7ST

145

94.5

1625

✔

25

3600

284TS

575

RGZP

Ball

1LA02842FP52

1574

SA-7ST

23

91

375

✔

125

1800

444T

575

RGZP

Roller

1LA04444FP51

9060

SA-7ST

116

94.5

1625

✔

390

✔

125

1200

445T

460

RGZP

Roller

1LA04456FP41

11056

SA-7ST

145

94.1

1900

✔

1200

445TS

460

RGZP

Ball

1LA04456FP42

11056

SA-7ST

145

94.1

1900

✔

25

1800

284T

230/460

RGZP

Ball

1LA02844FP21

1502

SA-7ST

29

92.4

1800

284T

575

RGZP

Ball

1LA02844FP51

1502

SA-7ST

23

92.4

375

✔

25

1200

324T

230/460

RGZP

Ball

1LA03246FP21

2480

SA-7ST

33

91.7

565

✔

125

1200

445T

575

RGZP

Roller

1LA04456FP51

11056

SA-7ST

116

94.1

1900

✔

25

1200

324T

575

RGZP

Ball

1LA03246FP51

2480

SA-7ST

26

91.7

565

✔

150

3600

445TS

460

RGZP

Ball

1LA04452FP42

12005

SA-7ST

165

94.5

1900

✔

30

3600

286TS

230/460

RGZP

Ball

1LA02862FP22

1861

SA-7ST

34

91

430

✔

150

3600

445TS

575

RGZP

Ball

1LA04452FP52

12005

SA-7ST

132

94.5

1900

✔

30

3600

286TS

575

RGZP

Ball

1LA02862FP52

1861

SA-7ST

27

91

430

✔

150

1800

445T

460

RGZP

Roller

1LA04454FP41

10700

SA-7ST

170

95

1900

✔

30

1800

286T

230/460

RGZP

Ball

1LA02864FP21

1770

SA-7ST

35

92.4

408

✔

150

1800

B445T

460

RGZP

Ball

1LA04454FP4N

10700

SA-7ST

170

95

1900

✔

30

1800

286T

575

RGZP

Ball

1LA02864FP51

1770

SA-7ST

28

92.4

407

✔

150

1800

445TS

460

RGZP

Ball

1LA04454FP42

10700

SA-7ST

170

95

1900

✔

30

1200

326T

230/460

RGZP

Ball

1LA03266FP21

3100

SA-7ST

39

91.7

600

✔

150

1800

445T

575

RGZP

Roller

1LA04454FP51

10700

SA-7ST

136

95

1900

✔

30

1200

326T

575

RGZP

Ball

1LA03266FP51

3100

SA-7ST

31

91.7

600

✔

150

1200

447T

460

RGZP

Roller

1LA04476FP41

12800

SA-7ST

171

95

2174

✔

40

3600

324TS

230/460

RGZP

Ball

1LA03242FP22

2412

SA-7ST

46

91.7

537

✔

150

1200

447TS

460

RGZP

Ball

1LA04476FP42

12800

SA-7ST

171

95

2174

✔

40

3600

324TS

575

RGZP

Ball

1LA03242FP52

2412

SA-7ST

37

91.7

537

✔

150

1200

447T

575

RGZP

Roller

1LA04476FP51

12800

SA-7ST

136

95

2174

✔

40

1800

324T

230/460

RGZP

Ball

1LA03244FP21

2330

SA-7ST

47

93

542

✔

200

3600

447TS

460

RGZP

Ball

1LA04472FP42

15245

SA-7ST

212

95

2280

✔

40

1800

324T

575

RGZP

Ball

1LA03244FP51

2330

SA-7ST

38

93

542

✔

200

3600

447TS

575

RGZP

Ball

1LA04472FP52

15254

SA-7ST

170

95

2280

✔

40

1200

364T

230/460

RGZP

Ball

1LA03646FP21

4105

SA-7ST

52

93

800

✔

200

1800

447T

460

RGZP

Roller

1LA04474FP41

13175

SA-7ST

225

95

2280

✔

800

✔

200

1800

447TS

460

RGZP

Ball

1LA04474FP42

13175

SA-7ST

225

95

2280

✔

92.4

580

✔

200

1800

447T

575

RGZP

Roller

1LA04474FP51

13175

SA-7ST

180

95

2280

✔

40

1200 3600

364T

575

RGZP

326TS

230/460

RGZP

Ball

1LA03646FP51

4105

SA-7ST

Ball

1LA03262FP22

3060

SA-7ST

42 55

93

575

RGZP

Ball

1LA03262FP52

3060

SA-7ST

44

92.4

580

✔

200

1200

449T

460

RGZP

Roller

1LA04496FP41

16000

SA-7ST

224

95

2363

✔

326T

230/460

RGZP

Ball

1LA03264FP21

2860

SA-7ST

58

93

600

✔

200

1200

449TS

460

RGZP

Ball

1LA04496FP42

16000

SA-7ST

224

95

2363

✔

50

1800

326T

575

RGZP

Ball

1LA03264FP51

2860

SA-7ST

46

93

600

✔

200

1200

449T

575

RGZP

Roller

1LA04496FP51

16000

SA-7ST

179

95

2363

✔

50

1200

365T

230/460

RGZP

Ball

1LA03656FP21

4778

SA-7ST

66

93

875

✔

50

1200

365T

575

RGZP

Ball

1LA03656FP51

4778

SA-7ST

53

93

875

✔

1

3600

143TC

230/460

RGZPF

Ball

1LA01432FP27

339

SA-7STD

1.4

75.5

50

✔

60

3600

364TS

230/460

RGZP

Ball

1LA03642FP22

4277

SA-7ST

68

93

709

✔

1

1800

143TC

230/460

RGZPF

Ball

1LA01444FP27

339

SA-7STD

1.5

82.5

45

3600

364TS

575

RGZP

Ball

1LA03642FP52

4227

SA-7ST

54

93

709

✔

✔

60

1

1200

145TC

230/460

RGZPF

Ball

1LA01456FP27

406

SA-7STD

1.8

80

55

1800

364T

230/460

RGZP

Ball

1LA03644FP21

4284

SA-7ST

71

93.6

720

✔

✔

60

1.5

3600

143TC

230/460

RGZPF

Ball

1LA01442FP27

346

SA-7STD

2

82.5

50

1800

364T

575

RGZP

Ball

1LA03644FP51

4284

SA-7ST

57

93.6

800

✔

✔

60

1.5

1800

145TC

230/460

RGZPF

Ball

1LA01454FP27

368

SA-7STD

2.2

84

55

1200

404T

230/460

RGZP

Ball

1LA04046FP21

5690

SA-7ST

74

93.6

1135

✔

✔

60

1.5

1200

182TC

230/460

RGZPF

Ball

1LA01826FP27

456

SA-7STD

2.3

85.5

85

60

1200

404T

575

RGZP

Ball

1LA04046FP51

5690

SA-7ST

59

93.6

1135

✔

✔

2

3600

145TC

230/460

RGZPF

Ball

1LA01452FP27

394

SA-7STD

2.5

84

49

3600

365TS

230/460

RGZP

Ball

1LA03652FP22

5324

SA-7ST

85

93

875

✔

✔

75

2

1800

145TC

230/460

RGZPF

Ball

1LA01464FP27

395

SA-7STD

2.9

84

55

3600

365TS

575

RGZP

Ball

1LA03652FP52

5324

SA-7ST

68

93

875

✔

✔

75

2

1200

184TC

230/460

RGZPF

Ball

1LA01846FP27

496

SA-7STD

3

86.5

100

1800

365T

230/460

RGZP

Ball

1LA03654FP21

5490

SA-7ST

87

94.1

875

✔

✔

75

3

3600

182TC

230/460

RGZPF

Ball

1LA01822FP27

456

SA-7STD

3.7

85.5

85

1800

365T

575

RGZP

Ball

1LA03654FP51

5490

SA-7ST

70

94.1

875

✔

✔

75

3

1800

182TC

230/460

RGZPF

Ball

1LA01824FP27

469

SA-7STD

3.9

87.5

85

1200

405T

230/460

RGZP

Ball

1LA04056FP21

6730

SA-7ST

93

93.6

1300

✔

✔

75

3

1200

213TC

230/460

RGZPF

Ball

1LA02136FP27

616

SA-7STD

4

87.5

135

1200

405T

575

RGZP

Ball

1LA04056FP51

6730

SA-7ST

74

93.6

1300

✔

✔

75

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2-16

2007 Low Voltage AC Motors Selection and Pricing Guide

C-Face, Horizontal, Foot Mounted

* FL amps are at 460V or 575V depending on the voltage rating of motor.

Shaded ratings will be discontinued when present stock is depleted. Replaced by type GP10.

DOE#CC032A

DOE#CC032A

Shaded ratings will be discontinued when present stock is depleted. Replaced by type GP10.

2007 Low Voltage AC Motors Selection and Pricing Guide

2-17

NEMA PREMIUM Severe Duty

326TS

1800

NEMA PREMIUM General Purpose

3600

50

HIGH EFFICIENT P-Base Vertical

50

HIGH EFFICIENT Definite Purpose

25

125

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT P-Base Vertical

Frame

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

NEMA PREMIUM General Purpose

RPM

DE Bearing

RGZP

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Definite Purpose

RGZP

50

NEMA PREMIUM Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Voltage

Type

Part Number

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Horizontal, Foot Mounted - continued 5

3600

184TC

230/460

RGZPF

Ball

1LA01842FP27

571

SA-7STD

5.8

87.5

100

✔

5

1800

184TC

230/460

RGZPF

Ball

1LA01844FP27

524

SA-7STD

6.5

87.5

100

✔

5

1200

215TC

230/460

RGZPF

Ball

1LA02156FP27

881

SA-7STD

6.8

87.5

160

✔

7.5

3600

213TC

230/460

RGZPF

Ball

1LA02132FP27

723

SA-7STD

8.8

88.5

135

✔

7.5

1800

213TC

230/460

RGZPF

Ball

1LA02134FP27

703

SA-7STD

9.5

89.5

135

✔

7.5

1200

254TC

230/460

RGZPF

Ball

1LA02546FP27

1179

SA-7STD

9.8

89.5

245

✔

10

3600

215TC

230/460

RGZPF

Ball

1LA02152FP27

839

SA-7STD

12

89.5

160

✔

10

1800

215TC

230/460

RGZPF

Ball

1LA02154FP27

839

SA-7STD

13

89.5

160

✔

10

1200

256TC

230/460

RGZPF

Ball

1LA02566FP27

1369

SA-7STD

13

89.5

285

✔

15

3600

254TC

230/460

RGZPF

Ball

1LA02542FP27

1146

SA-7STD

17

90.2

245

✔

15

1800

254TC

230/460

RGZPF

Ball

1LA02544FP27

1121

SA-7STD

19

91

245

✔

15

1200

284TC

230/460

RGZPF

Ball

1LA02846FP27

1870

SA-7STD

20

90.2

375

✔

20

3600

256TC

230/460

RGZPF

Ball

1LA02562FP27

1394

SA-7STD

23

90.2

285

✔

20

1800

256TC

230/460

RGZPF

Ball

1LA02564FP27

1329

SA-7STD

26

91

285

✔

20

1200

286TC

230/460

RGZPF

Ball

1LA02866FP27

2210

SA-7STD

26

90.2

430

✔

C-Face, Vertical with Drip Cover, Footless 230/460

RGZPV

Ball

1LA01432FP23

445

SA-7STD

1.4

75.5

50

✔

1

1800 143TCV

230/460

RGZPV

Ball

1LA01444FP23

445

SA-7STD

1.5

82.5

44

✔

1

1200 145TCV

230/460

RGZPV

Ball

1LA01456FP23

515

SA-7STD

1.8

80

55

✔

1.5

3600 143TCV

230/460

RGZPV

Ball

1LA01442FP23

452

SA-7STD

2

82.5

50

✔

1.5

1800 145TCV

230/460

RGZPV

Ball

1LA01454FP23

474

SA-7STD

2.2

84

55

✔

1.5

1200 182TCV

230/460

RGZPV

Ball

1LA01826FP23

539

SA-7STD

2.3

85.5

85

✔

2

3600 145TCV

230/460

RGZPV

Ball

1LA01452FP23

500

SA-7STD

2.5

84

49

✔

2

1800 145TCV

230/460

RGZPV

Ball

1LA01464FP23

501

SA-7STD

2.9

84

55

✔

2

1200 184TCV

230/460

RGZPV

Ball

1LA01846FP23

579

SA-7STD

3

86.5

100

✔

3

3600 182TCV

230/460

RGZPV

Ball

1LA01822FP23

539

SA-7STD

3.7

85.5

85

✔

3

1800 182TCV

230/460

RGZPV

Ball

1LA01824FP23

552

SA-7STD

3.9

87.5

85

✔

3

1200 213TCV

230/460

RGZPV

Ball

1LA02136FP23

699

SA-7STD

4

87.5

135

✔

5

3600 184TCV

230/460

RGZPV

Ball

1LA01842FP23

654

SA-7STD

5.8

87.5

100

✔

5

1800 184TCV

230/460

RGZPV

Ball

1LA01844FP23

607

SA-7STD

6.5

87.5

100

✔

5

1200 215TCV

230/460

RGZPV

Ball

1LA02156FP23

964

SA-7STD

6.8

87.5

160

✔

7.5

3600 213TCV

230/460

RGZPV

Ball

1LA02132FP23

806

SA-7STD

8.8

88.5

135

✔

7.5

1800 213TCV

230/460

RGZPV

Ball

1LA02134FP23

786

SA-7STD

9.5

89.5

135

✔

7.5

1200 254TCV

230/460

RGZPV

Ball

1LA02546FP23

1293

SA-7STD

9.8

89.5

245

✔

3600 215TCV

230/460

RGZPV

Ball

1LA02152FP23

922

SA-7STD

12

89.5

160

✔

1800 215TCV

230/460

RGZPV

Ball

1LA02154FP23

922

SA-7STD

13

89.5

160

✔

10

1200 256TCV

230/460

RGZPV

Ball

1LA02566FP23

1483

SA-7STD

13

89.5

285

✔

15

3600 254TCV

230/460

RGZPV

Ball

1LA02542FP23

1260

SA-7STD

17

90.2

245

✔

15

1800 254TCV

230/460

RGZPV

Ball

1LA02544FP23

1235

SA-7STD

19

91

245

✔

15

1200 284TCV

230/460

RGZPV

Ball

1LA02846FP23

2048

SA-7STD

20

90.2

380

✔

20

3600 256TCV

230/460

RGZPV

Ball

1LA02562FP23

1508

SA-7STD

23

90.2

285

✔

20

1800 256TCV

230/460

RGZPV

Ball

1LA02564FP23

1443

SA-7STD

26

91

298

✔

20

1200 286TCV

230/460

RGZPV

Ball

1LA02866FP23

2388

SA-7STD

26

90.2

430

✔

• • • •

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800, 1200 or 900 RPM 3 phase, 60 Hz; 208-230/460 and 575 volt operation Meets or exceeds EPAct efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 143T through 256T frame

Features for Long Life Frame & End Shields - Cast iron construction for exceptional structural integrity & corrosion resistance, equipped with integrally cast feet and condensation T-drains. Lifting provisions are included for frames 180T to 256T. Unique frame design maximizes cooling. Rotor - A unique offset rotor bar design provides improved efficiency. Large cross section bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings - Regreasable, oversized double shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. All motors are equipped with drive end and opposite drive end shaft V-ring slingers for added bearing protection. Provisions for Inpro/Seal® bearing isolators are standard on both ends.

Oversized Conduit Box - Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - All cast iron construction, structural foam fan, zincplated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable - Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

10 10

• • • •

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31 making all motors suitable for operation with variable frequency drives.

HIGH EFFICIENT P-Base Vertical

3600 143TCV

Performance Specifications

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Definite Purpose

1

The new SD10 series of severe duty TEFC motors meets or exceeds EPAct Efficiency standards. They are ideal for both indoor and outdoor applications and in severe operating atmospheres. These industry workhorses are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

Frame

Multiplier FL Symbol Amps*

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Definite Purpose

RPM

List Price $

SD10

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM General Purpose

RGZP DE Bearing

Introduction

Severe Duty - TEFC Motors

General Purpose - TEFC Motors

2-18

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-19

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Shaded ratings will be discontinued when present stock is depleted. Replaced by type GP10.

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Price $

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

HP

RPM

Stock/Modifiable Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

143T

208-230/460

SD10

Ball

1LE23011AA114AA3

350

SD1

1.4

80

65

✔

7.5

3600

213T

208-230/460

SD10

Ball

1LE23012AA114AA3

736

SD1

9

88.5

156

✔

3600

143T

575

SD10

Ball

1LE23011AA113AA3

350

SD1

1.12

80

65

✔

7.5

3600

213T

575

SD10

Ball

1LE23012AA113AA3

736

SD1

7.2

88.5

156

✔

1

1800

143T

208-230/460

SD10

Ball

1LE23011AB214AA3

336

SD1

1.5

82.5

67

✔

7.5

1800

213T

208-230/460

SD10

Ball

1LE23012AB114AA3

726

SD1

9.5

89.5

163

✔

1

1800

143T

575

SD10

Ball

1LE23011AB213AA3

336

SD1

1.2

82.5

67

✔

7.5

1800

213T

575

SD10

Ball

1LE23012AB113AA3

726

SD1

7.6

89.5

163

✔

1

1200

145T

208-230/460

SD10

Ball

1LE23011AC314AA3

418

SD1

1.6

80

67

✔

7.5

1200

254T

208-230/460

SD10

Ball

1LE23012BC114AA3

1222

SD1

10.5

89.5

253

✔

1

1200

145T

575

SD10

Ball

1LE23011AC313AA3

418

SD1

1.28

80

67

✔

7.5

1200

254T

575

SD10

Ball

1LE23012BC113AA3

1222

SD1

8.4

89.5

253

✔

1

900

182T

208-230/460

SD10

Ball

1LE23011CD114AA3

655

SD1

2.1

81.5

106

✔

7.5

900

256T

208-230/460

SD10

Ball

1LE23012BD214AA3

1879

SD1

13

87.5

279

✔

1

900

182T

575

SD10

Ball

1LE23011CD113AA3

655

SD1

1.64

81.5

106

✔

7.5

900

256T

575

SD10

Ball

1LE23012BD213AA3

1879

SD1

10.4

87.5

279

✔

1.5

3600

143T

208-230/460

SD10

Ball

1LE23011AA214AA3

355

SD1

2

82.5

66

✔

10

3600

215T

208-230/460

SD10

Ball

1LE23012AA214AA3

863

SD1

11.5

89.5

170

✔

1.5

3600

143T

575

SD10

Ball

1LE23011AA213AA3

355

SD1

1.6

82.5

66

✔

10

3600

215T

575

SD10

Ball

1LE23012AA213AA3

863

SD1

9.2

89.5

170

✔

1.5

1800

145T

208-230/460

SD10

Ball

1LE23011AB314AA3

373

SD1

2.2

84

71

✔

10

1800

215T

208-230/460

SD10

Ball

1LE23012AB214AA3

877

SD1

12.5

89.5

170

✔

1.5

1800

145T

575

SD10

Ball

1LE23011AB313AA3

373

SD1

1.76

84

71

✔

10

1800

215T

575

SD10

Ball

1LE23012AB213AA3

877

SD1

10

89.5

170

✔

1.5

1200

182T

208-230/460

SD10

Ball

1LE23011CC114AA3

464

SD1

2.4

85.5

103

✔

10

1200

256T

208-230/460

SD10

Ball

1LE23012BC214AA3

1476

SD1

13.5

89.5

265

✔

1.5

1200

182T

575

SD10

Ball

1LE23011CC113AA3

464

SD1

1.92

85.5

103

✔

10

1200

256T

575

SD10

Ball

1LE23012BC213AA3

1476

SD1

10.8

89.5

265

✔

1.5

900

184T

208-230/460

SD10

Ball

1LE23011CD314AA3

737

SD1

3

82.5

119

✔

15

3600

254T

208-230/460

SD10

Ball

1LE23012BA114AA3

1185

SD1

18

90.2

257

✔

1.5

900

184T

575

SD10

Ball

1LE23011CD313AA3

737

SD1

2.4

82.5

119

✔

15

3600

254T

575

SD10

Ball

1LE23012BA113AA3

1185

SD1

14.4

90.2

257

✔

2

3600

145T

208-230/460

SD10

Ball

1LE23011AA314AA3

422

SD1

2.6

84

68

✔

15

1800

254T

208-230/460

SD10

Ball

1LE23012BB114AA3

1162

SD1

19

91

256

✔

2

3600

145T

575

SD10

Ball

1LE23011AA313AA3

422

SD1

2.08

84

68

✔

15

1800

254T

575

SD10

Ball

1LE23012BB113AA3

1162

SD1

15.2

91

256

✔

2

1800

145T

208-230/460

SD10

Ball

1LE23011AB414AA3

408

SD1

3

84

73

✔

20

3600

256T

208-230/460

SD10

Ball

1LE23012BA214AA3

1467

SD1

23.5

90.2

70

✔

2

1800

145T

575

SD10

Ball

1LE23011AB413AA3

408

SD1

2.4

84

73

✔

20

3600

256T

575

SD10

Ball

1LE23012BA213AA3

1467

SD1

18.8

90.2

70

✔

2

1200

184T

208-230/460

SD10

Ball

1LE23011CC314AA3

517

SD1

3.1

86.5

114

✔

20

1800

256T

208-230/460

SD10

Ball

1LE23012BB214AA3

1433

SD1

25

91

275

✔

2

1200

184T

575

SD10

Ball

1LE23011CC313AA3

517

SD1

2.48

86.5

114

✔

20

1800

256T

575

SD10

Ball

1LE23012BB213AA3

1433

SD1

20

91

275

✔

2

900

213T

208-230/460

SD10

Ball

1LE23012AD114AA3

856

SD1

3.3

84

143

✔

2

900

213T

575

SD10

Ball

1LE23012AD113AA3

856

SD1

2.64

84

143

✔

1

3600

143TC 208-230/460

SD10

Ball

1LE23011AA114GA3

417

SD1

1.4

80

65

✔

3

3600

182T

208-230/460

SD10

Ball

1LE23011CA114AA3

474

SD1

3.7

85.5

105

✔

1

3600

143TC 575

SD10

Ball

1LE23011AA113GA3

417

SD1

1.12

80

65

3

3600

182T

575

SD10

Ball

1LE23011CA113AA3

474

SD1

2.96

85.5

105

✔

1

1800

143TC 208-230/460

SD10

Ball

1LE23011AB214GA3

403

SD1

1.5

82.5

67

3

1800

182T

208-230/460

SD10

Ball

1LE23011CB114AA3

457

SD1

4

87.5

108

✔

1

1800

143TC 575

SD10

Ball

1LE23011AB213GA3

403

SD1

1.2

82.5

67

3

1800

182T

575

SD10

Ball

1LE23011CB113AA3

457

SD1

3.2

87.5

108

✔

1

1200

145TC 208-230/460

SD10

Ball

1LE23011AC314GA3

485

SD1

1.6

80

67

3

1200

213T

208-230/460

SD10

Ball

1LE23012AC114AA3

640

SD1

4

87.5

145

✔

1

1200

145TC 575

SD10

Ball

1LE23011AC313GA3

485

SD1

1.28

80

67

3

1200

213T

575

SD10

Ball

1LE23012AC113AA3

640

SD1

3.36

87.5

145

✔

1

900

182TC 208-230/460

SD10

Ball

1LE23011CD114GA3

754

SD1

2.1

81.5

106

3

900

215T

208-230/460

SD10

Ball

1LE23012AD214AA3

1180

SD1

4.8

85.5

158

✔

1

900

182TC 575

SD10

Ball

1LE23011CD113GA3

754

SD1

1.64

81.5

106

3

900

215T

575

SD10

Ball

1LE23012AD213AA3

1180

SD1

3.84

85.5

158

✔

1.5

3600

143TC 208-230/460

SD10

Ball

1LE23011AA214GA3

422

SD1

2

82.5

66

5

3600

184T

208-230/460

SD10

Ball

1LE23011CA314AA3

595

SD1

6.2

87.5

111

✔

1.5

3600

143TC 575

SD10

Ball

1LE23011AA213GA3

422

SD1

1.6

82.5

66

5

3600

184T

575

SD10

Ball

1LE23011CA313AA3

595

SD1

4.96

87.5

111

✔

1.5

1800

145TC 208-230/460

SD10

Ball

1LE23011AB314GA3

440

SD1

2.2

84

71

5

1800

184T

208-230/460

SD10

Ball

1LE23011CB314AA3

531

SD1

6.7

87.5

114

✔

1.5

1800

145TC 575

SD10

Ball

1LE23011AB313GA3

440

SD1

1.76

84

71

5

1800

184T

575

SD10

Ball

1LE23011CB313AA3

531

SD1

5.36

87.5

114

✔

1.5

1200

182TC 208-230/460

SD10

Ball

1LE23011CC114GA3

563

SD1

2.4

85.5

103

5

1200

215T

208-230/460

SD10

Ball

1LE23012AC214AA3

917

SD1

6.8

87.5

160

✔

1.5

1200

182TC 575

SD10

Ball

1LE23011CC113GA3

563

SD1

1.92

85.5

103

5

1200

215T

575

SD10

Ball

1LE23012AC213AA3

917

SD1

5.44

87.5

160

✔

1.5

900

184TC 208-230/460

SD10

Ball

1LE23011CD314GA3

836

SD1

3

82.5

119

5

900

254T

208-230/460

SD10

Ball

1LE23012BD114AA3

1660

SD1

8.8

86.5

247

✔

1.5

900

184TC 575

SD10

Ball

1LE23011CD313GA3

836

SD1

2.4

82.5

119

5

900

254T

575

SD10

Ball

1LE23012BD113AA3

1660

SD1

7.04

86.5

247

✔

C-Face, Horizontal, Footless

✔ ✔ ✔ ✔ ✔ ✔ ✔

NEMA PREMIUM General Purpose

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-21

NEMA PREMIUM Severe Duty

2-20

HIGH EFFICIENT P-Base Vertical

3600

1

HIGH EFFICIENT Definite Purpose

1

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

SD10

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

SD10

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Type

Part Number

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model ✔

C-Face, Horizontal, Footless - continued 2

3600

145TC

208-230/460

SD10

Ball

1LE23011AA314GA3

489

SD1

2.6

84

68

2

3600

145TC

575

SD10

Ball

1LE23011AA313GA3

489

SD1

2.08

84

68

2

1800

145TC

208-230/460

SD10

Ball

1LE23011AB414GA3

475

SD1

3

84

73

2

1800

145TC

575

SD10

Ball

1LE23011AB413GA3

475

SD1

2.4

84

73

2

1200

184TC

208-230/460

SD10

Ball

1LE23011CC314GA3

616

SD1

3.1

86.5

114

2

1200

184TC

575

SD10

Ball

1LE23011CC313GA3

616

SD1

2.48

86.5

114

2

900

213TC

208-230/460

SD10

Ball

1LE23012AD114GA3

955

SD1

3.3

84

143

2

900

213TC

575

SD10

Ball

1LE23012AD113GA3

955

SD1

2.64

84

143

3

3600

182TC

208-230/460

SD10

Ball

1LE23011CA114GA3

573

SD1

3.7

85.5

105

3

3600

182TC

575

SD10

Ball

1LE23011CA113GA3

573

SD1

2.96

85.5

105

3

1800

182TC

208-230/460

SD10

Ball

1LE23011CB114GA3

556

SD1

4

87.5

108

3

1800

182TC

575

SD10

Ball

1LE23011CB113GA3

556

SD1

3.2

87.5

108

3

1200

213TC

208-230/460

SD10

Ball

1LE23012AC114GA3

739

SD1

4

87.5

145

3

1200

213TC

575

SD10

Ball

1LE23012AC113GA3

739

SD1

3.36

87.5

145

3

900

215TC

208-230/460

SD10

Ball

1LE23012AD214GA3

1279

SD1

4.8

85.5

158

3

900

215TC

575

SD10

Ball

1LE23012AD213GA3

1279

SD1

3.84

85.5

158

5

3600

184TC

208-230/460

SD10

Ball

1LE23011CA314GA3

694

SD1

6.2

87.5

111

5

3600

184TC

575

SD10

Ball

1LE23011CA313GA3

694

SD1

4.96

87.5

111

5

1800

184TC

208-230/460

SD10

Ball

1LE23011CB314GA3

630

SD1

6.7

87.5

114

5

1800

184TC

575

SD10

Ball

1LE23011CB313GA3

630

SD1

5.36

87.5

114

5

1200

215TC

208-230/460

SD10

Ball

1LE23012AC214GA3

1016

SD1

6.8

87.5

160

5

1200

215TC

575

SD10

Ball

1LE23012AC213GA3

1016

SD1

5.44

87.5

160

5

900

254TC

208-230/460

SD10

Ball

1LE23012BD114GA3

1794

SD1

8.8

86.5

247

900

254TC

575

SD10

Ball

1LE23012BD113GA3

1794

SD1

7.04

86.5

247

3600

213TC

208-230/460

SD10

Ball

1LE23012AA114GA3

835

SD1

9

88.5

156

7.5

3600

213TC

575

SD10

Ball

1LE23012AA113GA3

835

SD1

7.2

88.5

156

1800

213TC

208-230/460

SD10

Ball

1LE23012AB114GA3

825

SD1

9.5

89.5

163

7.5

1800

213TC

575

SD10

Ball

1LE23012AB113GA3

825

SD1

7.6

89.5

163

7.5

1200

254TC

208-230/460

SD10

Ball

1LE23012BC114GA3

1356

SD1

10.5

89.5

253

7.5

1200

254TC

575

SD10

Ball

1LE23012BC113GA3

1356

SD1

8.4

89.5

253

7.5

900

256TC

208-230/460

SD10

Ball

1LE23012BD214GA3

2013

SD1

13

87.5

279

7.5

900

256TC

575

SD10

Ball

1LE23012BD213GA3

2013

SD1

10.4

87.5

279

10

3600

215TC

208-230/460

SD10

Ball

1LE23012AA214GA3

962

SD1

11.5

89.5

170

10

3600

215TC

575

SD10

Ball

1LE23012AA213GA3

962

SD1

9.2

89.5

170

10

1800

215TC

208-230/460

SD10

Ball

1LE23012AB214GA3

976

SD1

12.5

89.5

170

10

1800

215TC

575

SD10

Ball

1LE23012AB213GA3

976

SD1

10

89.5

170

10

1200

256TC

208-230/460

SD10

Ball

1LE23012BC214GA3

1610

SD1

13.5

89.5

265

10

1200

256TC

575

SD10

Ball

1LE23012BC213GA3

1610

SD1

10.8

89.5

265

3600

254TC

208-230/460

SD10

Ball

1LE23012BA114GA3

1319

SD1

18

90.2

257

15

3600

254TC

575

SD10

Ball

1LE23012BA113GA3

1319

SD1

14.4

90.2

257

15

1800

254TC

208-230/460

SD10

Ball

1LE23012BB114GA3

1296

SD1

19

91

256

15

1800

254TC

575

SD10

Ball

1LE23012BB113GA3

1296

SD1

15.2

91

256

20

3600

256TC

208-230/460

SD10

Ball

1LE23012BA214GA3

1601

SD1

23.5

90.2

275

20

3600

256TC

575

SD10

Ball

1LE23012BA213GA3

1601

SD1

18.8

90.2

275

1800

256TC

208-230/460

SD10

Ball

1LE23012BB214GA3

1567

SD1

25

91

275

20

1800

256TC

575

SD10

Ball

1LE23012BB213GA3

1567

SD1

20

91

275

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system is suitable for operation with variable frequency drives.

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

•1 to 200 HP •1.15 service factor, 40°C ambient •3600, 1800, 1200 or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 100 HP, 460 volt 100 HP and above; 575 volt available •Meets or exceeds EPAct efficiency standards •Class F insulation, Class B temperature rise •NEMA Design B, Continuous Duty •143T through 449T frame

Features for Long Life Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to 449T. Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Greaseable, oversized single shielded with cast iron inner caps (404T–449T frames). Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T–256T frames have a drive end shaft seal and 284T–449T frames have a drive end shaft V-ring slinger.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90° increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Specifications table begins on the next page

✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2-22

DOE#CC032A 2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-23

NEMA PREMIUM Severe Duty

20

✔

NEMA PREMIUM General Purpose

15

Performance Specifications

✔

HIGH EFFICIENT P-Base Vertical

7.5

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity.

HIGH EFFICIENT Definite Purpose

5 7.5

Severe Duty TEFC motors are ideal for both indoor and outdoor applications and in severe operating atmospheres. These motors are ideal for use in chemical processing, material handling, pump, fan, compressor and other industrial applications.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Voltage

List Price $

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Frame

DE Bearing

RGZPSD

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RPM

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

SD10 HP

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Multiplier Price $ Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

HP

RPM

Stock/Modifiable

Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

1

3600

143T

230/460

RGZPSD

Ball

1LA01432SP21

350

SA-7SD

1.4

75.5

50

✔

50

3600

326TS

230/460

RGZPSD

Ball

1LA03262SP22

3562

SA-7SD

55

92.4

580

✔

1

1800

143T

230/460

RGZPSD

Ball

1LA01444SP21

336

SA-7SD

1.5

82.5

50

✔

50

1800

326T

230/460

RGZPSD

Ball

1LA03264SP21

3264

SA-7SD

58

93

600

✔

1

1200

145T

230/460

RGZPSD

Ball

1LA01456SP21

418

SA-7SD

1.8

80

55

✔

50

1800

326TS

230/460

RGZPSD

Ball

1LA03264SP22

3264

SA-7SD

58

93

600

✔

1

900

182T

230/460

RGZPSD

Ball

1LA01828SP21

655

SA-7SD

1.9

78.5

85

✔

50

1200

365T

230/460

RGZPSD

Ball

1LA03656SP21

5290

SA-7SD

66

93

875

✔

1.5

3600

143T

230/460

RGZPSD

Ball

1LA01442SP21

355

SA-7SD

2

82.5

50

✔

60

3600

364TS

230/460

RGZPSD

Ball

1LA03642SP22

4754

SA-7SD

68

93

709

✔

1.5

1800

145T

230/460

RGZPSD

Ball

1LA01454SP21

373

SA-7SD

2.2

84

55

✔

60

1800

364T

230/460

RGZPSD

Ball

1LA03644SP21

4744

SA-7SD

71

93.6

800

✔

1.5

1200

182T

230/460

RGZPSD

Ball

1LA01826SP21

464

SA-7SD

2.3

85.5

1.5

900

184T

230/460

RGZPSD

Ball

1LA01848SP21

737

SA-7SD

2.6

80

85

✔

60

1800

364TS

230/460

RGZPSD

Ball

1LA03644SP22

4744

SA-7SD

71

93.6

720

✔

100

✔

60

1200

404T

230/460

RGZPSD

Ball

1LA04046SP21

6231

SA-7SD

74

93.6

1135

✔

2

3600

145T

230/460

RGZPSD

Ball

1LA01452SP21

422

SA-7SD

2.5

84

55

✔

75

3600

365TS

230/460

RGZPSD

Ball

1LA03652SP22

5974

SA-7SD

85

93

875

✔

2

1800

145T

230/460

RGZPSD

Ball

1LA01464SP21

408

SA-7SD

2.9

84

61

✔

75

1800

365T

230/460

RGZPSD

Ball

1LA03654SP21

6033

SA-7SD

87

94.1

875

✔

2

1200

184T

230/460

RGZPSD

Ball

1LA01846SP21

517

SA-7SD

3

86.5

100

✔

75

1800

365TS

230/460

RGZPSD

Ball

1LA03654SP22

6033

SA-7SD

87

94.1

850

✔

2

900

213T

230/460

RGZPSD

Ball

1LA02138SP21

856

SA-7SD

3.3

82.5

135

✔

75

1200

405T

230/460

RGZPSD

Ball

1LA04056SP21

7346

SA-7SD

93

93.6

1300

✔

3600

182T

230/460

RGZPSD

Ball

1LA01822SP21

474

SA-7SD

3.7

85.5

85

✔

100 3600

405TS

460

RGZPSD

Ball

1LA04052SP42

7999

SA-7SD

112

93.6

1300

✔

1800

182T

230/460

RGZPSD

Ball

1LA01824SP21

457

SA-7SD

3.9

87.5

85

✔

100 1800

405T

460

RGZPSD

Ball

1LA04054SP41

7435

SA-7SD

114

94.5

1300

✔

3

1200

213T

230/460

RGZPSD

Ball

1LA02136SP21

640

SA-7SD

4

87.5

135

✔

100 1800

405TS

460

RGZPSD

Ball

1LA04054SP42

7435

SA-7SD

114

94.5

1152

✔

3

900

215T

230/460

RGZPSD

Ball

1LA02158SP21

1180

SA-7SD

4.7

84

160

✔

100 1200

444T

460

RGZPSD

Roller

1LA04446SP41

10058

SA-7SD

117

94.1

1625

✔

5

3600

184T

230/460

RGZPSD

Ball

1LA01842SP21

595

SA-7SD

5.8

87.5

100

✔

100 1200

444TS

460

RGZPSD

Ball

1LA04446SP42

10058

SA-7SD

117

94.1

1625

✔

5

1800

184T

230/460

RGZPSD

Ball

1LA01844SP21

531

SA-7SD

6.5

87.5

100

✔

125 3600

444TS

460

RGZPSD

Ball

1LA04442SP42

10600

SA-7SD

138

94.5

1625

✔

5

1200

215T

230/460

RGZPSD

Ball

1LA02156SP21

917

SA-7SD

6.8

87.5

160

✔

125 1800

444T

460

RGZPSD

Roller

1LA04444SP41

9857

SA-7SD

145

94.5

1566

✔

5

900

254T

230/460

RGZPSD

Ball

1LA02548SP21

1660

SA-7SD

7.5

86.5

245

✔

125 1800

444TS

460

RGZPSD

Ball

1LA04444SP42

9857

SA-7SD

145

94.5

1625

✔

7.5

3600

213T

230/460

RGZPSD

Ball

1LA02132SP21

736

SA-7SD

8.8

88.5

135

✔

125 1200

445T

460

RGZPSD

Roller

1LA04456SP41

12252

SA-7SD

145

94.1

1900

✔

7.5

1800

213T

230/460

RGZPSD

Ball

1LA02134SP21

726

SA-7SD

9.5

89.5

157

✔

125 1200

445TS

460

RGZPSD

Ball

1LA04456SP42

12252

SA-7SD

145

94.1

1900

✔

7.5

1200

254T

230/460

RGZPSD

Ball

1LA02546SP21

1222

SA-7SD

9.8

89.5

245

✔

150 3600

445TS

460

RGZPSD

Ball

1LA04452SP42

12840

SA-7SD

165

94.5

1900

✔

7.5

900

256T

230/460

RGZPSD

Ball

1LA02568SP21

1879

SA-7SD

12

87.5

285

✔

150 1800

445T

460

RGZPSD

Roller

1LA04454SP41

11515

SA-7SD

170

95

1900

✔

10

3600

215T

230/460

RGZPSD

Ball

1LA02152SP21

863

SA-7SD

12

89.5

160

✔

150 1800

445TS

460

RGZPSD

Ball

1LA04454SP42

11515

SA-7SD

170

95

1900

✔

10

1800

215T

230/460

RGZPSD

Ball

1LA02154SP21

877

SA-7SD

13

89.5

160

✔

150 1200

447T

460

RGZPSD

Roller

1LA04476SP41

13851

SA-7SD

171

95

2280

✔

10

1200

256T

230/460

RGZPSD

Ball

1LA02566SP21

1476

SA-7SD

13

89.5

285

✔

150 1200

447TS

460

RGZPSD

Ball

1LA04476SP42

13851

SA-7SD

171

95

2174

✔

10

900

284T

230/460

RGZPSD

Ball

1LA02848SP21

2225

SA-7SD

15

91

375

✔

200 3600

447TS

460

RGZPSD

Ball

1LA04472SP42

16261

SA-7SD

212

95

2280

✔

15

3600

254T

230/460

RGZPSD

Ball

1LA02542SP21

1185

SA-7SD

17

90.2

245

✔

200 1800

447T

460

RGZPSD

Roller

1LA04474SP41

14059

SA-7SD

225

95

2110

✔

1800

254T

230/460

RGZPSD

Ball

1LA02544SP21

1162

SA-7SD

19

91

245

✔

200 1800

447TS

460

RGZPSD

Ball

1LA04474SP42

14059

SA-7SD

225

95

2280

✔

1200

284T

230/460

RGZPSD

Ball

1LA02846SP21

1974

SA-7SD

20

90.2

375

✔

200 1200

449T

460

RGZPSD

Roller

1LA04496SP41

17067

SA-7SD

224

95

2600

✔

15

900

286T

230/460

RGZPSD

Ball

1LA02868SP21

3184

SA-7SD

23

91

430

✔

200 1200

449TS

460

RGZPSD

Ball

1LA04496SP42

17067

SA-7SD

224

95

2363

✔

20

3600

256T

230/460

RGZPSD

Ball

1LA02562SP21

1467

SA-7SD

23

90.2

285

✔

1800

256T

230/460

RGZPSD

Ball

1LA02564SP21

1433

SA-7SD

26

91

285

✔

1200

286T

230/460

RGZPSD

Ball

1LA02866SP21

2392

SA-7SD

26

90.2

430

✔

20

900

324T

230/460

RGZPSD

Ball

1LA03248SP21

3830

SA-7SD

31

91

565

✔

25

3600

284TS

230/460

RGZPSD

Ball

1LA02842SP22

1800

SA-7SD

29

91

375

✔

25

1800

284T

230/460

RGZPSD

Ball

1LA02844SP21

1719

SA-7SD

29

92.4

390

✔

25

1800

284TS

230/460

RGZPSD

Ball

1LA02844SP22

1719

SA-7SD

29

92.4

375

✔

25

1200

324T

230/460

RGZPSD

Ball

1LA03246SP21

2890

SA-7SD

33

91.7

565

✔

30

3600

286TS

230/460

RGZPSD

Ball

1LA02862SP22

2110

SA-7SD

34

91

430

✔

30

1800

286T

230/460

RGZPSD

Ball

1LA02864SP21

2006

SA-7SD

35

92.4

408

✔

30

1800

286TS

230/460

RGZPSD

Ball

1LA02864SP22

2006

SA-7SD

35

92.4

408

✔

30

1200

326T

230/460

RGZPSD

Ball

1LA03266SP21

3410

SA-7SD

39

91.7

600

✔

3600

324TS

230/460

RGZPSD

Ball

1LA03242SP22

2769

SA-7SD

46

91.7

537

✔

1800

324T

230/460

RGZPSD

Ball

1LA03244SP21

2658

SA-7SD

47

93

542

✔

40

1800

324TS

230/460

RGZPSD

Ball

1LA03244SP22

2658

SA-7SD

47

93

542

✔

40

1200

364T

230/460

RGZPSD

Ball

1LA03646SP21

4590

SA-7SD

52

93

800

✔

Shaded ratings (all RGZPSD motors) will be discontinued when present stock is depleted. 140-250 frame replaced by type SD 10. 280-440 frames replaced by type RGZESD.

2-24

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-25

NEMA PREMIUM Severe Duty

40 40

NEMA PREMIUM General Purpose

20 20

Shaded ratings (all RGZPSD motors) will be discontinued when present stock is depleted. 140-250 frame replaced by type SD 10. 280-440 frames replaced by type RGZESD.

HIGH EFFICIENT P-Base Vertical

15 15

HIGH EFFICIENT Definite Purpose

3 3

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

RGZPSD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RGZPSD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

High efficiency severe duty TEFC motors are ideal for both indoor and outdoor applications and in severe duty operating atmospheres. These motors are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical.

Performance Specifications • 1 to 400 HP • 1.15 service factor, 40ºC ambient • 3600, 1800, 1200, 900 or 720 RPM • 3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available • Meets or exceeds NEMA efficiency standards • Class F insulation, Class B temperature rise • NEMA Design B, Continuous Duty • 143T through S449 frame

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to S449.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-449T frames have a drive end shaft V-ring slinger.

NEMA PREMIUM General Purpose

Voltage

Type

Part Number

Stock Model

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

1

1800

143T

230/460

RGZESD

Ball

1LA91444YK60

362

SA-7XSD

1.5

82.5

53

✔

1

1800

143T

575

RGZESD

Ball

1LA91444YK00

362

SA-7XSD

1.2

82.5

50

✔

1

1800

143T

200

RGZESD

Ball

1LA91444YK40

362

SA-7XSD

3.5

82.5

50

✔

1

1200

145T

230/460

RGZESD

Ball

1LA91456YK60

449

SA-7XSD

1.8

80

55

✔

1

1200

145T

575

RGZESD

Ball

1LA91456YK00

449

SA-7XSD

1.4

80

55

✔

1

900

182T

230/460

RGZESD

Ball

1LA91828YK60

742

SA-7XSD

1.9

78.5

85

✔

1

900

182T

575

RGZESD

Ball

1LA91828YK00

742

SA-7XSD

1.5

78.5

77

✔

1.5

3600

143T

230/460

RGZESD

Ball

1LA91442YK60

387

SA-7XSD

2

82.5

50

✔

1.5

3600

143T

575

RGZESD

Ball

1LA91442YK00

387

SA-7XSD

1.6

82.5

50

✔

1.5

1800

145T

230/460

RGZESD

Ball

1LA91454YK60

402

SA-7XSD

2.2

84

70

✔

1.5

1800

145T

575

RGZESD

Ball

1LA91454YK00

402

SA-7XSD

1.8

84

55

✔

1.5

1800

145T

200

RGZESD

Ball

1LA91454YK40

402

SA-7XSD

5.1

84

55

✔

1.5

1200

182T

230/460

RGZESD

Ball

1LA91826YK60

507

SA-7XSD

2.3

85.5

85

✔

1.5

1200

182T

575

RGZESD

Ball

1LA91826YK00

507

SA-7XSD

1.8

85.5

85

✔

1.5

900

184T

230/460

RGZESD

Ball

1LA91848YK60

875

SA-7XSD

2.6

80

100

✔

1.5

900

184T

575

RGZESD

Ball

1LA91848YK00

875

SA-7XSD

2.1

80

90

✔

2

3600

145T

230/460

RGZESD

Ball

1LA91452YK60

463

SA-7XSD

2.5

84

55

✔

2

3600

145T

575

RGZESD

Ball

1LA91452YK00

463

SA-7XSD

2

84

55

✔

2

1800

145T

230/460

RGZESD

Ball

1LA91464YK60

442

SA-7XSD

2.9

84

62

✔

2

1800

145T

575

RGZESD

Ball

1LA91464YK00

442

SA-7XSD

2.3

84

59

✔

2

1800

145T

200

RGZESD

Ball

1LA91464YK40

442

SA-7XSD

6.7

84

55

✔

2

1200

184T

230/460

RGZESD

Ball

1LA91846YK60

566

SA-7XSD

3

86.5

100

✔

2

1200

184T

575

RGZESD

Ball

1LA91846YK00

566

SA-7XSD

2.4

86.5

100

✔

2

900

213T

230/460

RGZESD

Ball

1LA92138YK60

1047

SA-7XSD

3.3

82.5

135

✔

2

900

213T

575

RGZESD

Ball

1LA92138YK00

1047

SA-7XSD

2.6

82.5

117

✔

3

3600

182T

230/460

RGZESD

Ball

1LA91822YK60

522

SA-7XSD

3.6

86.5

85

✔

3

3600

182T

575

RGZESD

Ball

1LA91822YK00

522

SA-7XSD

2.9

86.5

85

✔

3

1800

182T

230/460

RGZESD

Ball

1LA91824YK60

490

SA-7XSD

3.9

87.5

85

✔

3

1800

182T

575

RGZESD

Ball

1LA91824YK00

490

SA-7XSD

3.1

87.5

85

✔

3

1800

182T

200

RGZESD

Ball

1LA91824YK40

490

SA-7XSD

9

87.5

85

✔

3

1200

213T

230/460

RGZESD

Ball

1LA92136YK60

691

SA-7XSD

4

87.5

135

✔

3

1200

213T

575

RGZESD

Ball

1LA92136YK00

691

SA-7XSD

3.2

87.5

135

✔

3

900

215T

230/460

RGZESD

Ball

1LA92158YK60

1306

SA-7XSD

4.7

84

160

✔

3

900

215T

575

RGZESD

Ball

1LA92158YK00

1306

SA-7XSD

3.8

84

146

✔

5

3600

184T

230/460

RGZESD

Ball

1LA91842YK60

646

SA-7XSD

5.8

87.5

100

✔

5

3600

184T

575

RGZESD

Ball

1LA91842YK00

646

SA-7XSD

4.6

87.5

100

✔

5

1800

184T

230/460

RGZESD

Ball

1LA91844YK60

573

SA-7XSD

6.5

87.5

100

✔

5

1800

184T

575

RGZESD

Ball

1LA91844YK00

573

SA-7XSD

5.2

87.5

100

✔

5

1800

184T

200

RGZESD

Ball

1LA91844YK40

573

SA-7XSD

87.5

100

✔

5

1200

215T

230/460

RGZESD

Ball

1LA92156YK60

973

SA-7XSD

6.8

88.5

160

✔

5

1200

215T

575

RGZESD

Ball

1LA92156YK00

973

SA-7XSD

5.4

88.5

160

✔

5

900

254T

230/460

RGZESD

Ball

1LA92548YK60

1735

SA-7XSD

7.5

86.5

245

✔

5

900

254T

575

RGZESD

Ball

1LA92548YK00

1735

SA-7XSD

6.0

86.5

225

✔

7.5

3600

213T

230/460

RGZESD

Ball

1LA92132YK60

781

SA-7XSD

8.8

88.5

151

✔

7.5

3600

213T

575

RGZESD

Ball

1LA92132YK00

781

SA-7XSD

7

88.5

135

✔

7.5

1800

213T

230/460

RGZESD

Ball

1LA92134YK60

776

SA-7XSD

9.5

89.5

157

✔

7.5

1800

213T

575

RGZESD

Ball

1LA92134YK00

776

SA-7XSD

7.6

89.5

157

✔

7.5

1800

213T

200

RGZESD

Ball

1LA92134YK40

776

SA-7XSD

21.9

89.5

157

✔

DOE#CC032A

15

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD10.

2007 Low Voltage AC Motors Selection and Pricing Guide

2-27

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

Weight (lbs.)

Horizontal, Foot Mounted

*FL Amps are at 200V, 460V, or 575V depending on the voltage rating of the motor.

2-26

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

NEMA PREMIUM Severe Duty

Frame

FL Amps*

HIGH EFFICIENT P-Base Vertical

Specifications table begins on the next page

RPM

List Multiplier Price $ Symbol

HIGH EFFICIENT Definite Purpose

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31 making all motors suitable for operation with variable frequency drives.

HP

DE Bearing

HIGH EFFICIENT Hazardous Duty

Features for Long Life

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RGZESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

RGZESD

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Hazardous Duty

Type

Part Number

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

1200

254T

230/460

RGZESD

RPM

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

Horizontal, Foot Mounted - continued 7.5

HP

DE Bearing

Ball

1LA92546YK60

1293

SA-7XSD

7.5

1200

254T

575

RGZESD

Ball

1LA92546YK00

1293

SA-7XSD

7.5

900

256T

230/460

RGZESD

Ball

1LA92568YK60

2190

SA-7XSD

7.5

900

256T

575

RGZESD

Ball

1LA92568YK00

2190

SA-7XSD

10

3600

215T

230/460

RGZESD

Ball

1LA92152YK60

913

SA-7XSD

10

3600

215T

575

RGZESD

Ball

1LA92152YK00

913

SA-7XSD

9.8 7.8 12 9.6 12 9.6

245

✔

30

1200

326T

460

RGZESD

Ball

1LA03266SE41

3566

SA-7XSD

39

92.4

669

✔

90.2

245

✔

30

1200

326T

575

RGZESD

Ball

1LA03266SE51

3566

SA-7XSD

31.2

92.4

600

✔

87.5

285

✔

30

900

364T

460

RGZESD

Ball

1LA03648SE41

5598

SA-7XSD

47

91

800

✔

87.5

266

✔

30

900

364T

575

RGZESD

Ball

5598

SA-7XSD

37.6

91

800

89.5

160

✔

40

3600

324T

460

RGZESD

Ball

1LA03242SE41

2948

SA-7XSD

45

93.6

565

✔

89.5

160

✔

40

3600

324TS

460

RGZESD

Ball

1LA03242SE42

2948

SA-7XSD

45

93.6

565

✔

90.2

10

1800

215T

230/460

RGZESD

Ball

1LA92154YK60

935

SA-7XSD

13

89.5

174

✔

40

3600

324TS

575

RGZESD

Ball

1LA03242SE52

2948

SA-7XSD

36

93.6

565

✔

10

1800

215T

575

RGZESD

Ball

1LA92154YK00

935

SA-7XSD

10.4

89.5

160

✔

40

1800

324T

460

RGZESD

Ball

1LA03244SE41

2823

SA-7XSD

47

93.6

565

✔

10

1800

215T

200

RGZESD

Ball

1LA92154YK40

935

SA-7XSD

29.9

89.5

160

✔

40

1800

324TS

460

RGZESD

Ball

1LA03244SE42

2823

SA-7XSD

47

93.6

565

✔

10

1200

256T

230/460

RGZESD

Ball

1LA92566YK60

1580

SA-7XSD

13

90.2

285

✔

40

1800

324T

575

RGZESD

Ball

1LA03244SE51

2823

SA-7XSD

37.6

93.6

565

✔

10

1200

256T

575

RGZESD

Ball

1LA92566YK00

1580

SA-7XSD

10.4

90.2

285

✔

40

1200

364T

460

RGZESD

Ball

1LA03646SE41

4833

SA-7XSD

52

93.6

800

✔

10

900

284T

230/460

RGZESD

Ball

1LA02848SE21

2557

SA-7XSD

15

91

375

✔

40

1200

364T

575

RGZESD

Ball

1LA03646SE51

4833

SA-7XSD

41.6

93.6

800

✔

10

900

284T

575

RGZESD

Ball

1LA02848SE51

2557

SA-7XSD

12

91

375

✔

40

900

365T

460

RGZESD

Ball

1LA03658SE41

6769

SA-7XSD

63

91.7

875

✔

15

3600

254T

230/460

RGZESD

Ball

1LA92542YK60

1254

SA-7XSD

17

90.2

245

✔

40

900

365T

575

RGZESD

Ball

6769

SA-7XSD

50.4

91.7

875

15

3600

254T

575

RGZESD

Ball

1LA92542YK00

1254

SA-7XSD

13.6

90.2

245

✔

50

3600

326T

460

RGZESD

Ball

1LA03262SE41

3814

SA-7XSD

55

93.6

710

✔

245

✔

50

3600

326TS

460

RGZESD

Ball

1LA03262SE42

3814

SA-7XSD

55

93.6

710

✔

245

✔

50

3600

326TS

575

RGZESD

Ball

1LA03262SE52

3814

SA-7XSD

44

93.6

600

✔

1800

326T

460

RGZESD

Ball

1LA03264SE41

3467

SA-7XSD

58

93.6

600

✔

15

1800 1800

254T 254T

230/460 575

RGZESD RGZESD

Ball Ball

1LA92544YK60 1LA92544YK00

1232 1232

SA-7XSD SA-7XSD

19 15.2

91.7 91.7

15

1800

254T

200

RGZESD

Ball

1LA92544YK40

1232

SA-7XSD

43.7

91.7

245

✔

50

15

1200

284T

230/460

RGZESD

Ball

1LA02846SE21

2096

SA-7XSD

20

91

375

✔

50

1800

326TS

460

RGZESD

Ball

1LA03264SE42

3467

SA-7XSD

58

93.6

639

✔

15

1200

284T

575

RGZESD

Ball

1LA02846SE51

2096

SA-7XSD

16

91

375

✔

50

1800

326T

575

RGZESD

Ball

1LA03264SE51

3467

SA-7XSD

46.4

93.6

600

✔

15

900

286T

230/460

RGZESD

Ball

1LA02868SE21

3328

SA-7XSD

23

91

430

✔

50

1200

365T

460

RGZESD

Ball

1LA03656SE41

5549

SA-7XSD

66

93.6

875

✔

15

900

286T

575

RGZESD

Ball

3328

SA-7XSD

18.4

91

430

50

1200

365T

575

RGZESD

Ball

1LA03656SE51

5549

SA-7XSD

52.8

93.6

875

✔

1LA04048SE41

8088

SA-7XSD

67

91.7

1135

✔

8088

SA-7XSD

53.6

91.7

1135

20

3600

256T

230/460

RGZESD

Ball

1LA92562YK60

1553

SA-7XSD

23

90.2

285

✔

50

900

404T

460

RGZESD

Ball

20

3600

256T

575

RGZESD

Ball

1LA92562YK00

1553

SA-7XSD

18.4

90.2

285

✔

50

900

404T

575

RGZESD

Ball

20

1800

256T

230/460

RGZESD

Ball

1LA92564YK60

1535

SA-7XSD

26

91.7

322

✔

60

3600

364T

460

RGZESD

Ball

1LA03642SE41

5017

SA-7XSD

68

93.6

800

✔

20

1800

256T

575

RGZESD

Ball

1LA92564YK00

1535

SA-7XSD

20.8

91.7

285

✔

60

3600

364TS

460

RGZESD

Ball

1LA03642SE42

5017

SA-7XSD

68

93.6

800

✔

20

1800

256T

200

RGZESD

Ball

1LA92564YK40

1535

SA-7XSD

59.8

91.7

285

✔

60

3600

364TS

575

RGZESD

Ball

1LA03642SE52

5017

SA-7XSD

54.4

93.6

800

✔

20

1200

286T

230/460

RGZESD

Ball

1LA02866SE21

2554

SA-7XSD

26

91.7

430

✔

60

1800

364T

460

RGZESD

Ball

1LA03644SE41

4974

SA-7XSD

71

93.6

831

✔

20

1200

286T

575

RGZESD

Ball

1LA02866SE51

2554

SA-7XSD

20.8

91.7

430

✔

60

1800

364TS

460

RGZESD

Ball

1LA03644SE42

4974

SA-7XSD

71

93.6

800

✔

567

✔

60

1800

364T

575

RGZESD

Ball

1LA03644SE51

4974

SA-7XSD

56.8

93.6

800

✔

60

1200

404T

460

RGZESD

Ball

1LA04046SE41

6502

SA-7XSD

74

94.1

1135

✔

20

900

324T

230/460

RGZESD

Ball

900

324T

575

RGZESD

Ball

3600

284T

460

RGZESD

Ball

25

3600

284TS

460

RGZESD

Ball

1LA02842SE41 1LA02842SE42

4068

SA-7XSD

31

91

4068

SA-7XSD

24.8

91

567

1914

SA-7XSD

29

91.7

375

✔

60

1200

404T

575

RGZESD

Ball

1LA04046SE51

6502

SA-7XSD

59.2

94.1

1135

✔

91.7

375

✔

60

900

405T

460

RGZESD

Ball

1LA04058SE41

9239

SA-7XSD

78

91.7

1300

✔

62.4

91.7

1300

1914

SA-7XSD

29

3600

284TS

575

RGZESD

Ball

1LA02842SE52

1914

SA-7XSD

23.2

91.7

375

✔

60

900

405T

575

RGZESD

Ball

1800

284T

460

RGZESD

Ball

1LA02844SE41

1828

SA-7XSD

29

93

477

✔

60

720

444T

460

RGZESD

Roller

25

1800

284TS

460

RGZESD

Ball

1LA02844SE42

1828

SA-7XSD

29

93

375

✔

75

3600

365T

460

RGZESD

Ball

25

1800

284T

575

RGZESD

Ball

1LA02844SE51

1828

SA-7XSD

23.2

93

375

✔

75

3600

365TS

460

RGZESD

25

1200

324T

460

RGZESD

Ball

1LA03246SE41

3096

SA-7XSD

33

92.4

565

✔

75

3600

365TS

575

25

1200

324T

575

RGZESD

Ball

1LA03246SE51

3096

SA-7XSD

26.4

92.4

565

✔

75

1800

365T

25

900

326T

460

RGZESD

Ball

1LA03268SE41

4730

SA-7XSD

38

90.2

600

✔

75

1800

25

900

326T

575

RGZESD

Ball

4730

SA-7XSD

30.4

90.2

600

75

30

3600

286T

460

RGZESD

Ball

1LA02862SE41

2235

SA-7XSD

34

91.7

520

✔

30

3600

286TS

460

RGZESD

Ball

1LA02862SE42

2235

SA-7XSD

34

91.7

465

✔

SA-7XSD SA-7XSD

1LA03652SE41

6300

SA-7XSD

85

94.1

875

✔

Ball

1LA03652SE42

6300

SA-7XSD

85

94.1

875

✔

RGZESD

Ball

1LA03652SE52

6300

SA-7XSD

68

94.1

875

✔

460

RGZESD

Ball

1LA03654SE41

6305

SA-7XSD

87

94.1

875

✔

365TS

460

RGZESD

Ball

1LA03654SE42

6305

SA-7XSD

87

94.1

875

✔

1800

365T

575

RGZESD

Ball

1LA03654SE51

6305

SA-7XSD

69.6

94.1

875

✔

75

1200

405T

460

RGZESD

Ball

1LA04056SE41

7655

SA-7XSD

93

94.5

1300

✔

75

1200

405T

575

RGZESD

Ball

1LA04056SE51

7655

SA-7XSD

74.4

94.5

1300

✔

900

444T

460

RGZESD

Roller

1LA04448SE41

12175

SA-7XSD

94

93

1625

✔

75.2

93

1625

94.1

1300

✔

94.1

1300

✔

30

3600

286TS

575

RGZESD

Ball

1LA02862SE52

2235

SA-7XSD

27.2

91.7

430

✔

75

30

1800

286T

460

RGZESD

Ball

1LA02864SE41

2125

SA-7XSD

35

93

494

✔

75

900

444T

575

RGZESD

Roller

12175

SA-7XSD

494

✔

75

720

445T

460

RGZESD

Roller

17014

SA-7XSD

430

✔

100 3600

405TS

460

RGZESD

Ball

1LA04052SE42

8442

SA-7XSD

100 3600

405TS

575

RGZESD

Ball

1LA04052SE52

8442

SA-7XSD

30 30

1800 1800

286TS 286T

460 575

RGZESD RGZESD

Ball Ball

1LA02864SE42 1LA02864SE51

*FL Amps are at 200V, 460V, or 575V depending on the voltage rating of the motor.

2-28

2007 Low Voltage AC Motors Selection and Pricing Guide

2125 2125

SA-7XSD SA-7XSD

35 28

93 93

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD10.

DOE#CC032A

1900

1900 108 86.4

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-29

NEMA PREMIUM Severe Duty

9239 16035

NEMA PREMIUM General Purpose

25 25

HIGH EFFICIENT P-Base Vertical

20 25

1LA03248SE21

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

Voltage

Multiplier Symbol

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT P-Base Vertical

Frame

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

NEMA PREMIUM General Purpose

RPM

DE Bearing

RGZESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Multi Speed

RGZESD

15

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

HP

RPM

Frame

Stock/Modifiable Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

405TS

460

RGZESD

Ball

1LA04054SE42

7790

SA-7XSD

113

94.5

1300

✔

200 1200 B449T

460

RGZESD

Ball

1LA04496SE4N

17600

SA-7XSD

226

95

2625

✔

100 1800

405T

460

RGZESD

Ball

1LA04054SE41

7790

SA-7XSD

113

94.5

1300

✔

200 1200 449TS

460

RGZESD

Ball

1LA04496SE42

17600

SA-7XSD

226

95

2363

✔

100 1800

405T

575

RGZESD

Ball

1LA04054SE51

7790

SA-7XSD

94.5

1300

✔

200 1200 449T

460

RGZESD

Roller

1LA04496SE41

17600

SA-7XSD

226

95

2600

✔

100 1200

B444T

460

RGZESD

Ball

1LA04446SE4N

10462

SA-7XSD

117

94.5

1740

✔

200 1200 449T

575

RGZESD

Roller

1LA04496SE51

17600

SA-7XSD

180.8

95

2600

✔

100 1200

444TS

460

RGZESD

Ball

1LA04446SE42

10462

SA-7XSD

117

94.5

1566

✔

200

900 449T

460

RGZESD

Roller

1LA04498SE41

20700

SA-7XSD

241

94.5

2600

✔

100 1200

444T

460

RGZESD

Roller

1LA04446SE41

10462

SA-7XSD

117

94.5

1625

✔

200

900 449T

575

RGZESD

Roller

20700

SA-7XSD

192.8

94.5

2600

100 1200

444T

575

RGZESD

Roller

1LA04446SE51

10462

SA-7XSD

94.5

1625

✔

250 3600 449TS

460

RGZESD

Ball

1LA04492SE42

21150

SA-7XSD

267

95.4

2600

✔

100

900

445T

460

RGZESD

Roller

1LA04458SE41

15053

SA-7XSD

94.1

1900

✔

250 1800 449TS

460

RGZESD

Ball

1LA04494SE42

18192

SA-7XSD

281

95.8

2600

✔

100

900

445T

575

RGZESD

Roller

15053

SA-7XSD

94.1

1900

250 1800 B449T

460

RGZESD

Ball

1LA04494SE4N

18192

SA-7XSD

281

95.8

2625

✔

100

720

447T

460

RGZESD

Roller

21107

SA-7XSD

2280

250 1800 449T

460

RGZESD

Roller

1LA04494SE41

18192

SA-7XSD

281

95.8

2482

✔

125 3600

444TS

460

RGZESD

Ball

1LA04442SE42

11035

SA-7XSD

138

94.5

1552

✔

250 1800 449T

575

RGZESD

Roller

1LA04494SE51

18192

SA-7XSD

224.7

95.8

2482

✔

125 3600

444TS

575

RGZESD

Ball

1LA04442SE52

11035

SA-7XSD

110.4

94.5

1600

✔

250 1200 B449T

460

RGZESD

Ball

1LA04496HE4N

19152

SA-7XSD

280

95

2625

✔

125 1800

444TS

460

RGZESD

Ball

1LA04444SE42

10255

SA-7XSD

143

95

1625

✔

250 1200 449TS

460

RGZESD

Ball

1LA04496HE42

19152

SA-7XSD

280

95

2070

✔

125 1800

B444T

460

RGZESD

Ball

1LA04444SE4N

10255

SA-7XSD

143

95

1930

✔

250 1200 449T

460

RGZESD

Roller

1LA04496HE41

19152

SA-7XSD

280

95

2600

✔

125 1800

444T

460

RGZESD

Roller

1LA04444SE41

10255

SA-7XSD

143

95

1625

✔

250 1200 449T

575

RGZESD

Roller

1LA04496HE51

19152

SA-7XSD

224

95

2600

✔

125 1800

444TS

575

RGZESD

Ball

1LA04444SE52

10255

SA-7XSD

114.4

95

1625

✔

250

460

RGZESD

Roller

1LA02508HG41

29500

SA-7XSD

303

94.5

3316

✔

125 1800

444T

575

RGZESD

Roller

1LA04444SE51

10255

SA-7XSD

114.4

95

1625

✔

300 3600 449TS

460

RGZESD

Ball

1LA04492HE42

26319

SA-7XSD

323

95.8

2600

✔

125 1200

B445T

460

RGZESD

Ball

1LA04456SE4N

12850

SA-7XSD

144

94.5

1930

✔

300 1800 449TS

460

RGZESD

Ball

1LA04494HE42

19288

SA-7XSD

346

95.4

2352

✔

125 1200

445TS

460

RGZESD

Ball

1LA04456SE42

12850

SA-7XSD

144

94.5

1737

✔

300 1800 449T

460

RGZESD

Roller

1LA04494HE41

19288

SA-7XSD

346

95.4

2600

✔

125 1200

445T

460

RGZESD

Roller

1LA04456SE41

12850

SA-7XSD

144

94.5

1900

✔

300 1800 B449T

460

RGZESD

Ball

1LA04494HE4N

19288

SA-7XSD

346

95.4

2625

✔

125 1200

445T

575

RGZESD

Roller

1LA04456SE51

12850

SA-7XSD

115.2

94.5

1900

✔

300 1200 S449LS

460

RGZESD

Roller

1LA03006HG41

35702

SA-7XSD

336

95

3442

✔

125

900

447T

460

RGZESD

Roller

1LA04478SE41

16040

SA-7XSD

152

93.6

2280

✔

350 3600 S449SS

460

RGZESD

Ball 1

1LA03502HG42

33060

SA-7XSD

369

95.4

3063

✔

125

900

447T

575

RGZESD

Roller

16040

SA-7XSD

121.6

93.6

2280

350 1800 S449SS

460

RGZESD

Ball

1LA03504HG42

30612

SA-7XSD

390

95.8

3309

✔

125

720

449T

460

RGZESD

Roller

23907

SA-7XSD

2600

350 1800 S449LS

460

RGZESD

Roller

1LA03504HG41

30612

SA-7XSD

390

95.8

3346

✔

150 3600

445TS

460

RGZESD

Ball

1LA04452SE42

13257

SA-7XSD

164

95

1900

✔

350 1200 S449LS

460

RGZESD

Roller

1LA03506HG41

40642

SA-7XSD

395

95

3000

✔

150 3600

445TS

575

RGZESD

Ball

1LA04452SE52

13257

SA-7XSD

131.2

95

1700

✔

400 3600 S449SS

460

RGZESD

Ball 1

1LA04002HG42

37105

SA-7XSD

418

95.4

3217

✔

150 1800

445TS

460

RGZESD

Ball

1LA04454SE42

11922

SA-7XSD

170

95.8

1900

✔

400 1800 S449SS

460

RGZESD

Ball

1LA04004HG42

34365

SA-7XSD

449

95.8

3869

✔

150 1800

B445T

460

RGZESD

Ball

1LA04454SE4N

11922

SA-7XSD

170

95.8

1930

✔

400 1800 S449LS

460

RGZESD

Roller

1LA04004HG41

34365

SA-7XSD

449

95.8

3388

✔

150 1800

445T

460

RGZESD

Roller

1LA04454SE41

11922

SA-7XSD

170

95.8

1900

✔

400 1200 S449LS

460

RGZESD

Roller

43080

SA-7XSD

455

94.5

3050

150 1800

445TS

575

RGZESD

Ball

1LA04454SE52

11922

SA-7XSD

136

95.8

1900

✔

150 1800

445T

575

RGZESD

Roller

1LA04454SE51

11922

SA-7XSD

136

95.8

1900

✔

1

1800 143TCV 230/460

RGZVESD

Ball

1LA91444YK62

521

SA-7XSD

1.5

82.5

57

150 1200

B447T

460

RGZESD

Ball

1LA04476SE4N

14377

SA-7XSD

170

95

2415

✔

1

1200 145TCV 230/460

RGZVESD

Ball

1LA91456YK62

608

SA-7XSD

1.8

80

65

✔

150 1200

447TS

460

RGZESD

Ball

1LA04476SE42

14377

SA-7XSD

170

95

2174

✔

1

900 182TCV 230/460

RGZVESD

Ball

1LA91828YK62

901

SA-7XSD

1.9

78.5

85

✔

150 1200

447T

460

RGZESD

Roller

1LA04476SE41

14377

SA-7XSD

170

95

2280

✔

1.5

3600 143TCV 230/460

RGZVESD

Ball

1LA91442YK62

546

SA-7XSD

2

82.5

50

✔

150 1200

447T

575

RGZESD

Roller

1LA04476SE51

14377

SA-7XSD

136

95

2280

✔

1.5

1800 145TCV 230/460

RGZVESD

Ball

1LA91454YK62

561

SA-7XSD

2.2

84

55

✔

150

900

447T

460

RGZESD

Roller

1LA04478HE41

20400

SA-7XSD

186

94.1

2280

✔

1.5

1200 182TCV 230/460

RGZVESD

Ball

1LA91826YK62

666

SA-7XSD

2.3

85.5

85

✔

150

900

447T

575

RGZESD

Roller

20400

SA-7XSD

148.8

94.1

2280

1.5

900 184TCV 230/460

RGZVESD

Ball

1LA91848YK62

1034

SA-7XSD

2.6

80

100

✔

150

720

449T

460

RGZESD

Roller

25655

SA-7XSD

2600

2

3600 145TCV 230/460

RGZVESD

Ball

1LA91452YK62

622

SA-7XSD

2.5

84

55

✔

200 3600

447TS

460

RGZESD

Ball

1LA04472SE42

16770

SA-7XSD

216

95

2280

✔

2

1800 145TCV 230/460

RGZVESD

Ball

1LA91464YK62

601

SA-7XSD

2.9

84

55

✔

200 3600

447TS

575

RGZESD

Ball

1LA04472SE52

16770

SA-7XSD

172.8

95

2000

✔

2

1200 184TCV 230/460

RGZVESD

Ball

1LA91846YK62

725

SA-7XSD

3

86.5

100

✔

200 1800

B447T

460

RGZESD

Ball

1LA04474SE4N

14501

SA-7XSD

225

95.8

2015

✔

2

900 213TCV 230/460

RGZVESD

Ball

1LA92138YK62

1206

SA-7XSD

3.3

82.5

135

✔

200 1800

447TS

460

RGZESD

Ball

1LA04474SE42

14501

SA-7XSD

225

95.8

2280

✔

3

3600 182TCV 230/460

RGZVESD

Ball

1LA91822YK62

681

SA-7XSD

3.6

86.5

85

✔

200 1800

447T

460

RGZESD

Roller

1LA04474SE41

14501

SA-7XSD

225

95.8

2149

✔

3

1800 182TCV 230/460

RGZVESD

Ball

1LA91824YK62

649

SA-7XSD

3.9

87.5

85

✔

200 1800

447TS

575

RGZESD

Ball

1LA04474SE52

14501

SA-7XSD

180

95.8

2280

✔

3

1200 213TCV 230/460

RGZVESD

Ball

1LA92136YK62

850

SA-7XSD

4

87.5

135

✔

200 1800

447T

575

RGZESD

Roller

1LA04474SE51

14501

SA-7XSD

180

95.8

2280

✔

3

900 215TCV 230/460

RGZVESD

Ball

1LA92158YK62

1465

SA-7XSD

4.7

84

160

✔

90.4

93.6 123 98.4

DOE#CC032A

DOE#CC032A

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD10.

2007 Low Voltage AC Motors Selection and Pricing Guide

2-31

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

*FL Amps are at 460V or 575V depending on the voltage rating of the motor. 1 CW rotation facing opposite drive end

✔

NEMA PREMIUM General Purpose

2-30

C-Face, Vertical with Drip Cover, Footless

HIGH EFFICIENT P-Base Vertical

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

900 S449LS

HIGH EFFICIENT Definite Purpose

100 1800

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

RGZESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RGZESD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

List Multiplier Price $ Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Vertical with Drip Cover, Footless - continued

HP

RPM

Frame

Stock/Modifiable Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

C-Face, Vertical with Drip Cover, Footless - continued

3600

184TCV

230/460

RGZVESD

Ball

1LA91842YK62

805

SA-7XSD

5.8

87.5

100

✔

75

3600 365TSCV

460

RGZVESD

Ball

7023

SA-7XSD

85

94.1

850

5

1800

184TCV

230/460

RGZVESD

Ball

1LA91844YK62

732

SA-7XSD

6.5

87.5

100

✔

75

1800 365TSCV

460

RGZVESD

Ball

7028

SA-7XSD

87

94.1

850

5

1200

215TCV

230/460

RGZVESD

Ball

1LA92156YK62

1132

SA-7XSD

6.8

88.5

160

✔

75

1800 365TCV

460

RGZVESD

Ball

7028

SA-7XSD

87

94.1

850

5

900

254TCV

230/460

RGZVESD

Ball

1LA92548YK62

1948

SA-7XSD

7.5

86.5

245

✔

75

1200 405TCV

460

RGZVESD

Ball

8713

SA-7XSD

93

94.5

1250

7.5

3600

213TCV

230/460

RGZVESD

Ball

1LA92132YK62

940

SA-7XSD

8.8

88.5

135

✔

75

900 444TCV

460

RGZVESD

Ball

13845

SA-7XSD

94

93

1620

7.5

1800

213TCV

230/460

RGZVESD

Ball

1LA92134YK62

935

SA-7XSD

9.5

89.5

135

✔

100 3600 405TSCV

460

RGZVESD

Ball

9500

SA-7XSD

108

94.1

1250

7.5

1200

254TCV

230/460

RGZVESD

Ball

1LA92546YK62

1506

SA-7XSD

9.8

90.2

245

✔

100 1800 405TSCV

460

RGZVESD

Ball

8848

SA-7XSD

113

94.5

1250

7.5

900

256TCV

230/460

RGZVESD

Ball

1LA92568YK62

2403

SA-7XSD

12

87.5

285

✔

100 1800 405TCV

460

RGZVESD

Ball

8848

SA-7XSD

113

94.5

1250

10

3600

215TCV

230/460

RGZVESD

Ball

1LA92152YK62

1072

SA-7XSD

12

89.5

160

✔

100 1200 444TSCV

460

RGZVESD

Ball

12132

SA-7XSD

117

94.5

1620

10

1800

215TCV

230/460

RGZVESD

Ball

1LA92154YK62

1094

SA-7XSD

13

89.5

160

✔

100 1200 444TCV

460

RGZVESD

Ball

12132

SA-7XSD

117

94.5

1620

10

1200

256TCV

230/460

RGZVESD

Ball

1LA92566YK62

1793

SA-7XSD

13

90.2

285

✔

100

460

RGZVESD

Ball

16723

SA-7XSD

123

94.1

1740

10

900

284TCV

230/460

RGZVESD

Ball

2875

SA-7XSD

15

91

375

125 3600 444TSCV

460

RGZVESD

Ball

12075

SA-7XSD

138

94.5

1620

15

3600

254TCV

230/460

RGZVESD

Ball

1LA92542YK62

1467

SA-7XSD

17

90.2

245

✔

125 1800 444TSCV

460

RGZVESD

Ball

11925

SA-7XSD

143

95

1620

15

1800

254TCV

230/460

RGZVESD

Ball

1LA92544YK62

1445

SA-7XSD

19

91.7

245

✔

125 1800 444TCV

460

RGZVESD

Ball

11925

SA-7XSD

143

95

1620

15

1200

284TCV

230/460

RGZVESD

Ball

1LA02846SE23

2414

SA-7XSD

20

91

375

✔

125 1200 445TSCV

460

RGZVESD

Ball

14520

SA-7XSD

144

94.5

1740

15

900

286TCV

230/460

RGZVESD

Ball

3646

SA-7XSD

23

91

450

125 1200 445TCV

460

RGZVESD

Ball

14520

SA-7XSD

144

94.5

1740

20

3600

256TCV

230/460

RGZVESD

Ball

1LA92562YK62

1766

SA-7XSD

23

90.2

285

✔

125

460

RGZVESD

Ball

17710

SA-7XSD

152

93.6

2000

20

1800

256TCV

230/460

RGZVESD

Ball

1LA92564YK62

1748

SA-7XSD

26

91.7

285

✔

150 3600 445TSCV

460

RGZVESD

Ball

15197

SA-7XSD

164

95

1740

20

1200

286TCV

230/460

RGZVESD

Ball

1LA02866SE23

2872

SA-7XSD

26

91.7

430

✔

150 1800 445TSCV

460

RGZVESD

Ball

13592

SA-7XSD

170

95.8

1740

20

900

324TCV

230/460

RGZVESD

Ball

4488

SA-7XSD

31

91

565

150 1800 445TCV

460

RGZVESD

Ball

13592

SA-7XSD

170

95.8

1740

25

3600

284TSCV 460

RGZVESD

Ball

2232

SA-7XSD

29

91.7

375

150 1200 447TSCV

460

RGZVESD

Ball

16047

SA-7XSD

170

95

2000

25

1800

284TSCV 460

RGZVESD

Ball

1LA02844SE44

2146

SA-7XSD

29

93

375

✔

150 1200 447TCV

460

RGZVESD

Ball

16047

SA-7XSD

170

95

2000

25

1800

284TCV

460

RGZVESD

Ball

1LA02844SE43

2146

SA-7XSD

29

93

375

✔

150

460

RGZVESD

Ball

22070

SA-7XSD

186

94.1

2000

25

1200

324TCV

460

RGZVESD

Ball

3516

SA-7XSD

33

92.4

565

200 3600 447TSCV

460

RGZVESD

Ball

18440

SA-7XSD

216

95

2000

25

900

326TCV

460

RGZVESD

Ball

5150

SA-7XSD

38

90.2

640

200 1800 447TSCV

460

RGZVESD

Ball

16171

SA-7XSD

225

95.8

2000

30

3600

286TSCV 460

RGZVESD

Ball

2553

SA-7XSD

34

91.7

450

200 1800 447TCV

460

RGZVESD

Ball

16171

SA-7XSD

225

95.8

2000

30

1800

286TSCV 460

RGZVESD

Ball

1LA02864SE44

2443

SA-7XSD

35

93

430

✔

200 1200 449TCV

460

RGZVESD

Ball

19270

SA-7XSD

226

95

2300

30

1800

286TCV

460

RGZVESD

Ball

1LA02864SE43

2443

SA-7XSD

35

93

430

✔

200

900 449T CV

460

RGZVESD

Ball

22370

SA-7XSD

241

94.5

2300

30

1200

326TCV

460

RGZVESD

Ball

3986

SA-7XSD

39

92.4

640

250 3600 449TSCV

460

RGZVESD

Ball

22820

SA-7XSD

267

95.4

2300

364TCV

900 445TCV

900 447TCV

900 447TCV

900

460

RGZVESD

Ball

6321

SA-7XSD

47

91

830

250 1800 449TSCV

460

RGZVESD

Ball

19862

SA-7XSD

281

95.8

2300

3600

324TSCV 460

RGZVESD

Ball

3368

SA-7XSD

45

93.6

565

250 1800 449TCV

460

RGZVESD

Ball

19862

SA-7XSD

281

95.8

2300

40

1800

324TSCV 460

RGZVESD

Ball

1LA03244SE44

3243

SA-7XSD

47

93.6

565

✔

250 1200 449TSCV

460

RGZVESD

Ball

20822

SA-7XSD

280

95

2300

40

1800

324TCV

460

RGZVESD

Ball

1LA03244SE43

3243

SA-7XSD

47

93.6

565

✔

250 1200 449TCV

460

RGZVESD

Ball

20822

SA-7XSD

280

95

2300

1200

364TCV

460

RGZVESD

Ball

5556

SA-7XSD

52

93.6

830

300 3600 449TSCV

460

RGZVESD

Ball

27989

SA-7XSD

323

95.8

2300

900

365TCV

460

RGZVESD

Ball

7492

SA-7XSD

63

91.7

850

300 1800 449TSCV

460

RGZVESD

Ball

20958

SA-7XSD

346

95.4

2300

50

3600

326TSCV 460

RGZVESD

Ball

4234

SA-7XSD

55

93.6

600

300 1800 449TCV

460

RGZVESD

Ball

20958

SA-7XSD

346

95

2300

50

1800

326TSCV 460

RGZVESD

Ball

1LA03264SE44

3887

SA-7XSD

58

93.6

600

✔

1LA03264SE43

3887

SA-7XSD

58

93.6

600

✔

6272

SA-7XSD

66

93.6

850

50

1800

326TCV

460

RGZVESD

Ball

1200

365TCV

460

RGZVESD

Ball

404TCV

50

900

460

RGZVESD

Ball

9146

SA-7XSD

67

91.7

1100

60

3600

364TSCV 460

RGZVESD

Ball

5740

SA-7XSD

68

93.6

800

60

1800

364TSCV 460

RGZVESD

Ball

1LA03644SE44

5697

SA-7XSD

71

93.6

800

✔

60

1800

364TCV

460

RGZVESD

Ball

1LA03644SE43

5697

SA-7XSD

71

93.6

800

✔

60

1200

404TCV

460

RGZVESD

Ball

7560

SA-7XSD

74

94.1

1100

60

900

405TCV

460

RGZVESD

Ball

10297

SA-7XSD

78

91.7

1250

NEMA PREMIUM General Purpose

40 40

HIGH EFFICIENT P-Base Vertical

30 40

HIGH EFFICIENT Definite Purpose

5

50

Stock Model

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

DE Bearing

RGZESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RGZESD

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-33

NEMA PREMIUM Severe Duty

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD10.

2-32

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Motors

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Performance Specifications

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock.

• 1 to 250 HP • 1.15 service factor, 40ºC ambient • Speeds: – 1 winding, 1800/900 RPM, variable or constant torque – 2 windings, 1800/1200 or 1800/900 RPM, variable or constant torque • 3 phase, 60 Hz; 460 volt; 200, 230 & 575 volt available • Meets or exceeds NEMA efficiency standards • Class F insulation, Class B temperature rise • NEMA Design B, Continuous Duty • 143T through 449T frame

Features for Long Life

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-449T frames have a drive end shaft V-ring slinger.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Low 0.25

RPM 1800/900

Frame 143T

Voltage 460

Type RGZESD

DE Bearing Ball

Part Number LA91431YK701VT

List Price $ 521

Multiplier Symbol SA-7MM

1.5

0.37

1800/900

145T

460

RGZESD

Ball

LA91451YK701VT

559

SA-7MM

2

0.5

1800/900

182T

460

RGZESD

Ball

LA91821YK701VT

641

3

0.75

1800/900

184T

460

RGZESD

Ball

LA91841YK701VT

711

5

1.2

1800/900

184T

460

RGZESD

Ball

LA01845MS41

Weight (lbs.) 50

Stock ✔

60

✔

SA-7MM

90

✔

SA-7MM

105

✔

800

SA-7MM

105

✔

5

1.2

1800/900

213T

460

RGZESD

Ball

LA92131YK701VT

831

SA-7MM

135

✔

7.5

1.9

1800/900

213T

460

RGZESD

Ball

LA02135MS41

1080

SA-7MM

135

✔

7.5

1.9

1800/900

215T

460

RGZESD

Ball

LA92151YK701VT

1125

SA-7MM

160

✔

10

2.5

1800/900

215T

460

RGZESD

Ball

LA02155MS41

1300

SA-7MM

160

✔

10

2.5

1800/900

254T

460

RGZESD

Ball

LA92541YK701VT

1356

SA-7MM

245

✔

15

3.7

1800/900

254T

460

RGZESD

Ball

LA02545MS41

1680

SA-7MM

245

✔

15

3.7

1800/900

256T

460

RGZESD

Ball

LA92561YK701VT

1786

SA-7MM

285

✔

20

5

1800/900

256T

460

RGZESD

Ball

LA02565MS41

2120

SA-7MM

285

✔

20

5

1800/900

284T

460

RGZESD

Ball

LA02845SE41

2226

SA-7MM

375

✔

25

6.2

1800/900

284T

460

RGZESD

Ball

LA02845MS41

2540

SA-7MM

375

✔

25

6.2

1800/900

286T

460

RGZESD

Ball

LA02865SE41

2643

SA-7MM

430

✔

30

7.5

1800/900

286T

460

RGZESD

Ball

LA02865MS41

2975

SA-7MM

430

✔

7.5

1800/900

324T

460

RGZESD

Ball

LA03245SE41

3081

SA-7MM

565

✔

40

10

1800/900

326T

460

RGZESD

Ball

LA03265SE41

4093

SA-7MM

600

✔

50

12

1800/900

364T

460

RGZESD

Ball

LA03645SE41

5027

SA-7MM

831

✔

60

15

1800/900

365T

460

RGZESD

Ball

LA03655SE41

7212

SA-7MM

875

✔

75

19

1800/900

405T

460

RGZESD

Ball

LA04055SE41

9142

SA-7MM

1300

✔

100

25

1800/900

444TS

460

RGZESD

Ball

10331

SA-7MM

1625

125

31

1800/900

445TS

460

RGZESD

Ball

13162

SA-7MM

1900

30

150

37

1800/900

447TS

460

RGZESD

Ball

15887

SA-7MM

2280

200

50

1800/900

449TS

460

RGZESD

Ball

19103

SA-7MM

2600

250

62.5

1800/900

449TS

460

RGZESD

Ball

26378

SA-7MM

2600

Notes: 1. Available in RGZZESD designs. Contact factory for pricing.

Speeds Low Speed High Speed

L1 T1 T6

Lines L2 T2 T4

L3 T3 T5

T4 T5 T6 Open T1 T2 T3 Together

Conn. Y YY

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

High 1

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to 449T.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

HP Continuous

2007 Low Voltage AC Motors Selection and Pricing Guide

2-35

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

NEMA PREMIUM General Purpose

Specifications table begins on the next page

2-34

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

High efficiency severe duty multi-speed motors are ideal for both indoor and outdoor applications, and in severe duty operating atmospheres such as fans, pumps & blowers which require more than one base speed. They meet or exceed NEMA and CSA standards and the operational standards for severe operating environments.

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RGZESD - 1 Winding Variable Torque

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RGZESD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC Multi-Speed Motors

Introduction

Severe Duty - TEFC Multi-Speed Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty

HP Continuous High 1

Low 0.5

RPM 1800/900

Frame 145T

Voltage 460

Type RGZESD

DE Bearing Ball

1800/900

182T

460

RGZESD

Ball

619

SA-7MM

Part Number

List Price $ 562

Multiplier Symbol SA-7MM

Weight (lbs.) 60 90

High Speed Stock HP Continuous 3

Custom Build

Low Speed HP Continuous Syn. RPM DE Bearing Ball

List Price $ 948

Multiplier Symbol SA-7MM

Weight (lbs.) 135

1.5

0.75

2

1

1800/900

182T

460

RGZESD

Ball

695

SA-7MM

90

3

1.5

1800/900

184T

460

RGZESD

Ball

768

SA-7MM

105

5

1800

2.2

1.2

215T

460

RGZESD

Ball

1104

SA-7MM

160

5

2.5

1800/900

213T

460

RGZESD

Ball

896

SA-7MM

135

7.5

1800

3.3

1.9

254T

460

RGZESD

Ball

1576

SA-7MM

245

7.5

RPM 1800

1200 1.3

900 Frame Voltage 0.75 213T 460

Type RGZESD

Part Number

3.7

1800/900

215T

460

RGZESD

Ball

1250

SA-7MM

160

10

1800

4.4

2.5

256T

460

RGZESD

Ball

1931

SA-7MM

285

10

5

1800/900

254T

460

RGZESD

Ball

1586

SA-7MM

245

15

1800

6.7

3.7

284T

460

RGZESD

Ball

2251

SA-7MM

375

15

7.5

1800/900

256T

460

RGZESD

Ball

2022

SA-7MM

285

20

1800

8.9

5

286T

460

RGZESD

Ball

2802

SA-7MM

430

6.2

324T

460

RGZESD

Ball

3381

SA-7MM

565

7.5

20

10

1800/900

284T

460

RGZESD

Ball

2263

SA-7MM

375

25

1800

11

25

12.5

1800/900

286T

460

RGZESD

Ball

2682

SA-7MM

430

30

1800

13

326T

460

RGZESD

Ball

4061

SA-7MM

600

30

15

1800/900

324T

460

RGZESD

Ball

3274

SA-7MM

565

40

1800

18

10

364T

460

RGZESD

Ball

5248

SA-7MM

831

40

20

1800/900

326T

460

RGZESD

Ball

4171

SA-7MM

600

50

1800

22

12.5

365T

460

RGZESD

Ball

6677

SA-7MM

875

50

25

1800/900

364T

460

RGZESD

Ball

5368

SA-7MM

831

60

1800

27

15

404T

460

RGZESD

Ball

10010

SA-7MM

1135

60

30

1800/900

365T

460

RGZESD

Ball

7688

SA-7MM

875

75

1800

33

19

405T

460

RGZESD

Ball

12685

SA-7MM

1300

75

37.5

1800/900

405T

460

RGZESD

Ball

10171

SA-7MM

1300

100

1800

44

25

444T

460

RGZESD

Roller

15381

SA-7MM

1625 1900

50

1800/900

444T

460

RGZESD

Roller

12351

SA-7MM

1625

125

1800

55

31

445T

460

RGZESD

Roller

19678

SA-7MM

125

62.5

1800/900

445T

460

RGZESD

Roller

13578

SA-7MM

1900

150

1800

67

37

447T

460

RGZESD

Roller

23811

SA-7MM

2280

150

75

1800/900

447T

460

RGZESD

Roller

19056

SA-7MM

2280

200

1800

88

50

449T

460

RGZESD

Roller

28911

SA-7MM

2600

200

100

1800/900

449T

460

RGZESD

Roller

22939

SA-7MM

2600

Notes: 1. Available in RGZZESD designs. Contact factory for pricing.

Lines L2 T2 T4

L3 T3 T5

T4 T5 T6 Open T1 T2 T3 Together

Conn. Delta YY

Speeds Low Speed High Speed

L1 T1 T11

Lines L2 T2 T12

L3 T3 T13

Open T11 T12 T13 T1 T2 T3

HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

L1 T1 T6

Notes: 1. Only one of the low speeds may be selected. 2. Available in RGZZESD designs. Contact factory for pricing.

HIGH EFFICIENT Definite Purpose

Speeds Low Speed High Speed

HIGH EFFICIENT Hazardous Duty

100

Stock Model

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

RGZESD - 2 Winding Variable Torque

Custom Build

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

RGZESD - 1 Winding Constant Torque

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-36

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-37

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Definite Purpose

Severe Duty - TEFC Multi-Speed Motors

Introduction

Severe Duty - TEFC Multi-Speed Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty

High Speed

HP Continuous 3

Low Speed HP Continuous Syn. RPM

RPM 1200 1800 2

900 1.5

Frame Voltage Type 213T 460 RGZESD

DE Bearing Ball

Part Number

List Price $ 1041

Multiplier Symbol SA-7MM

Weight (lbs.) 135

5

1800 3.3

2.5

215T

460

RGZESD

Ball

1197

SA-7MM

160

7.5

1800 5 **

3.7 ** 254T

460

RGZESD

Ball

1709

SA-7MM

245

10

1800 6.6 ** 5 **

256T

460

RGZESD

Ball

2096

SA-7MM

285

15

1800 10 **

7.5 ** 284T

460

RGZESD

Ball

2440

SA-7MM

375

20

1800 13 **

10 ** 286T

460

RGZESD

Ball

2802

SA-7MM

430

25

1800 17

12.5

460

RGZESD

Ball

3669

SA-7MM

565

30

1800 20 **

15

326T

460

RGZESD

Ball

4727

SA-7MM

600

40

1800 26.8

20

364T

460

RGZESD

Ball

5701

SA-7MM

831

50

1800 33 **

25

365T

460

RGZESD

Ball

7260

SA-7MM

875

60

1800 40

30

404T

460

RGZESD

Ball

10884

SA-7MM

1135

324T

75

1800 50 **

37.5

405T

460

RGZESD

Ball

13769

SA-7MM

1300

100

1800 66

50

444T

460

RGZESD

Roller

16728

SA-7MM

1625

125

1800 84

62

445T

460

RGZESD

Roller

21415

SA-7MM

1900

150

1800 100

75

447T

460

RGZESD

Roller

25924

SA-7MM

2280

200

1800 133

100

449T

460

RGZESD

Roller

31248

SA-7MM

2600

L1 T1 T11

L3 T3 T13

Performance Specifications

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. Two series- connected normallyclosed Class B thermostats are supplied as standard.

• • • • •

1 to 300 HP 1.0 service factor, 40ºC ambient T3B temperature code 900, 1200, 1800, or 3600 RPM 3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available • Class F insulation, Class B temperature rise • NEMA design B, continuous duty • 143T through 449T frame

Features for Long Life

Open T11 T12 T13 T1 T2 T3

Frame and End Shields – Cast iron frame and end shields for exceptional structural integrity, with sintered condensation drains on 404T – 449T frames. Lifting eyebolts are included for frames 213T to 449T.

HIGH EFFICIENT P-Base Vertical

Bearings – Regreasable, oversized single shielded bearings with cast iron inner caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Frames 143T – 256T are equipped with a shaft seal on the drive end; 284T – 449T frames have a drive end V-ring slinger for added bearing life. Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

HIGH EFFICIENT Definite Purpose

Speeds Low Speed High Speed

Lines L2 T2 T12

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Hazardous Duty

** Class F Insulation, 1.0 Service Factor. Notes: 1. Only one of the low speeds may be selected. 2. Available in RGZZESD designs. Contact factory for pricing.

Stock Model

These high efficiency explosion-proof motors are UL® listed for dust ignition proof environments, and are suitable for use in Class I, Group D, Class II, Groups F & G, Division 1 hazardous areas. They are ideal for use in applications such as chemical processing, mining, foundry, pulp and paper, waste management, and petro/chemical.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD

Custom Build

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

RGZESD - 2 Winding Constant Torque

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Definite Purpose

Hazardous Duty Motors

Introduction

Severe Duty - TEFC Multi-Speed Motors

Specifications table begins on the next page

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-39

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-38

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

List Multiplier Price $ Symbol

Stock/Modifiable FL FL Nom. Amps* Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

1

1800

143T

230/460

RGZZESD

Ball

1MJ91444YP60

534

SA-7XXP

1.5

82.5

65

✔

1

1800

143T

575

RGZZESD

Ball

1MJ91444YP00

534

SA-7XXP

1.2

82.5

60

✔

1

1200

145T

230/460

RGZZESD

Ball

1MJ91456YP60

623

SA-7XXP

1.8

80

70

✔

1

1200

145T

575

RGZZESD

Ball

1MJ91456YP00

623

SA-7XXP

1.44

80

70

✔

1

900

182T

230/460

RGZZESD

Ball

1MJ91828YP60

1153

SA-7XXP

1.9

78.5

113

✔

1

900

182T

575

RGZZESD

Ball

1153

SA-7XXP

1.52

78.5

113

1.5

3600

143T

230/460

RGZZESD

Ball

1MJ91442YP60

560

SA-7XXP

2

82.5

60

✔

575

RGZZESD

Ball

1MJ91442YP00

560

SA-7XXP

1.6

82.5

60

✔

230/460

RGZZESD

Ball

1MJ91454YP60

575

SA-7XXP

2.2

84

70

✔

1.5

1800

145T

575

RGZZESD

Ball

1MJ91454YP00

575

SA-7XXP

1.76

84

75

✔

1.5

1200

182T

230/460

RGZZESD

Ball

1MJ91826YP60

682

SA-7XXP

2.3

85.5

100

✔

1.5

1200

182T

575

RGZZESD

Ball

1MJ91826YP00

682

SA-7XXP

1.84

85.5

100

✔

1.5

900

184T

230/460

RGZZESD

Ball

1MJ91848YP60

1360

SA-7XXP

2.6

80

117

✔

1.5

900

184T

575

RGZZESD

Ball

1360

SA-7XXP

2.08

80

117

2

3600

145T

230/460

RGZZESD

Ball

1MJ91452YP60

638

SA-7XXP

2.5

84

70

✔

2

3600

145T

575

RGZZESD

Ball

1MJ91452YP00

638

SA-7XXP

2

84

70

✔

2

1800

145T

230/460

RGZZESD

Ball

1MJ91464YP60

616

SA-7XXP

2.9

84

70

✔

2

1800

145T

575

RGZZESD

Ball

1MJ91464YP00

616

SA-7XXP

2.32

84

70

✔

2

1200

184T

230/460

RGZZESD

Ball

1MJ91846YP60

772

SA-7XXP

3

86.5

120

✔

2

1200

184T

575

RGZZESD

Ball

1MJ91846YP00

772

SA-7XXP

2.4

86.5

120

✔

2

900

213T

230/460

RGZZESD

Ball

1MJ92138YP60

1632

SA-7XXP

3.3

82.5

153

✔

2

900

213T

575

RGZZESD

Ball

1632

SA-7XXP

2.64

82.5

153

3

3600

182T

230/460

RGZZESD

Ball

1MJ91822YP60

698

SA-7XXP

3.6

86.5

100

✔

3

3600

182T

575

RGZZESD

Ball

1MJ91822YP00

698

SA-7XXP

2.88

86.5

100

✔

3

1800

182T

230/460

RGZZESD

Ball

1MJ91824YP60

695

SA-7XXP

3.9

87.5

100

✔

3

1800

182T

575

RGZZESD

Ball

1MJ91824YP00

695

SA-7XXP

3.12

87.5

100

✔

3

1200

213T

230/460

RGZZESD

Ball

1MJ92136YP60

942

SA-7XXP

4

87.5

160

✔

3

1200

213T

575

RGZZESD

Ball

1MJ92136YP00

942

SA-7XXP

3.2

87.5

160

✔

3

900

215T

230/460

RGZZESD

Ball

1MJ92158YP60

1962

SA-7XXP

4.7

84

171

✔

3

900

215T

575

RGZZESD

Ball

1962

SA-7XXP

3.76

84

171

5

3600

184T

230/460

RGZZESD

Ball

1MJ91842YP60

854

SA-7XXP

5.8

87.5

120

✔

5

3600

184T

575

RGZZESD

Ball

1MJ91842YP00

854

SA-7XXP

4.64

87.5

120

✔

5

1800

184T

230/460

RGZZESD

Ball

1MJ91844YP60

779

SA-7XXP

6.5

87.5

125

✔

5

1800

184T

575

RGZZESD

Ball

1MJ91844YP00

779

SA-7XXP

5.2

87.5

115

✔

5

1200

215T

230/460

RGZZESD

Ball

1MJ92156YP60

1230

SA-7XXP

6.8

88.5

180

✔

5

1200

215T

575

RGZZESD

Ball

1MJ92156YP00

1230

SA-7XXP

5.44

88.5

180

✔

5

900

254T

230/460

RGZZESD

Ball

1MJ92548YP60

2049

SA-7XXP

7.5

86.5

292

✔

5

900

254T

575

RGZZESD

Ball

2049

SA-7XXP

6

86.5

292

7.5

3600

213T

230/460

RGZZESD

Ball

1034

SA-7XXP

8.8

88.5

160

✔

1MJ92132YP60

7.5

3600

213T

575

RGZZESD

Ball

1MJ92132YP00

1034

SA-7XXP

7.04

88.5

160

✔

7.5

1800

213T

230/460

RGZZESD

Ball

1MJ92134YP60

1029

SA-7XXP

9.5

89.5

160

✔ ✔

1800

213T

575

RGZZESD

Ball

1MJ92134YP00

1029

SA-7XXP

7.6

89.5

160

1200

254T

230/460

RGZZESD

Ball

1MJ92546YP60

1598

SA-7XXP

9.8

90.2

265

✔

7.5

1200

254T

575

RGZZESD

Ball

1MJ92546YP00

1598

SA-7XXP

7.84

90.2

265

✔

1MJ92568YP60

87.5

324

✔

87.5

324

7.5

900

256T

230/460

RGZZESD

Ball

7.5

900

256T

575

RGZZESD

Ball

2513

SA-7XXP

2513

SA-7XXP

12 9.6

89.5

180

✔

SA-7XXP

10.4

89.5

180

✔

SA-7XXP

13

90.2

325

✔

1891

SA-7XXP

10.4

90.2

325

✔

3039

SA-7XXP

15

91

410

3039

SA-7XXP

12

91

410

1559

SA-7XXP

17

90.2

265

✔

1MJ92542YP00

1559

SA-7XXP

13.6

90.2

265

✔

Ball

1MJ92544YP60

1536

SA-7XXP

19

91.7

265

✔

RGZZESD

Ball

1MJ92544YP00

1536

SA-7XXP

15.2

91.7

265

✔

230/460

RGZZESD

Ball

1MJ02846XE21

2568

SA-7XXP

20

91

410

✔

284T

575

RGZZESD

Ball

1MJ02846XE51

2568

SA-7XXP

16

91

410

✔

900

286T

230/460

RGZZESD

Ball

3825

SA-7XXP

23

91

460

15

900

286T

575

RGZZESD

Ball

3825

SA-7XXP

18.4

91

460

20

3600

256T

230/460

RGZZESD

Ball

1MJ92562YP60

1864

SA-7XXP

23

90.2

325

✔

20

3600

256T

575

RGZZESD

Ball

1MJ92562YP00

1864

SA-7XXP

18.4

90.2

325

✔

20

1800

256T

230/460

RGZZESD

Ball

1MJ92564YP60

1845

SA-7XXP

26

91.7

325

✔

20

1800

256T

575

RGZZESD

Ball

1MJ92564YP00

1845

SA-7XXP

20.8

91.7

325

✔

20

1200

286T

230/460

RGZZESD

Ball

1MJ02866XE21

3036

SA-7XXP

26

91.7

460

✔

20

1200

286T

575

RGZZESD

Ball

1MJ02866XE51

3036

SA-7XXP

20.8

91.7

460

✔

20

900

324T

230/460

RGZZESD

Ball

4780

SA-7XXP

31

91

589

20

900

324T

575

RGZZESD

Ball

4780

SA-7XXP

24.8

91

589

25

3600

284TS

460

RGZZESD

Ball

1MJ02842XE42

2383

SA-7XXP

29

91.7

410

✔

25

3600

284TS

575

RGZZESD

Ball

1MJ02842XE52

2383

SA-7XXP

23.2

91.7

410

✔

25

1800

284T

460

RGZZESD

Ball

1MJ02844XE41

2295

SA-7XXP

29

93

410

✔

25

1800

284T

575

RGZZESD

Ball

1MJ02844XE51

2295

SA-7XXP

23.2

93

410

✔

25

1200

324T

460

RGZZESD

Ball

1MJ03246XE41

3788

SA-7XXP

33

92.4

589

✔

25

1200

324T

575

RGZZESD

Ball

1MJ03246XE51

3788

SA-7XXP

26.4

92.4

589

✔

25

900

326T

460

RGZZESD

Ball

5761

SA-7XXP

38

90.2

645

25

900

326T

575

RGZZESD

Ball

5761

SA-7XXP

30.4

90.2

645

30

3600

286TS

460

RGZZESD

Ball

1MJ02862XE42

2710

SA-7XXP

34

91.7

460

✔

30

3600

286TS

575

RGZZESD

Ball

1MJ02862XE52

2710

SA-7XXP

27.2

91.7

460

✔

30

1800

286T

460

RGZZESD

Ball

1MJ02864XE41

2598

SA-7XXP

35

93

460

✔

30

1800

286T

575

RGZZESD

Ball

1MJ02864XE51

2598

SA-7XXP

28

93

460

✔

30

1200

326T

460

RGZZESD

Ball

1MJ03266XE41

4268

SA-7XXP

39

92.4

645

✔

30

1200

326T

575

RGZZESD

Ball

1MJ03266XE51

4268

SA-7XXP

31.2

92.4

645

✔

30

900

364T

460

RGZZESD

Ball

6504

SA-7XXP

47

91

865

30

900

364T

575

RGZZESD

Ball

6504

SA-7XXP

37.6

91

865

RGZZESD

Ball

1MJ92152YP60

1169

SA-7XXP

575

RGZZESD

Ball

1MJ92152YP00

1169

SA-7XXP

10

1800

215T

230/460

RGZZESD

Ball

1MJ92154YP60

1191

SA-7XXP

10

1800

215T

575

RGZZESD

Ball

1MJ92154YP00

1191

10

1200

256T

230/460

RGZZESD

Ball

1MJ92566YP60

1891

10

1200

256T

575

RGZZESD

Ball

1MJ92566YP00

10

900

284T

230/460

RGZZESD

Ball

10

900

284T

575

RGZZESD

Ball

15

3600

254T

230/460

RGZZESD

Ball

1MJ92542YP60

15

3600

254T

575

RGZZESD

Ball

15

1800

254T

230/460

RGZZESD

15

1800

254T

575

15

1200

284T

15

1200

15

12 9.6

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2-40

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-41

NEMA PREMIUM Severe Duty

7.5 7.5

✔

13

230/460

215T

NEMA PREMIUM General Purpose

143T 145T

✔

215T

3600

HIGH EFFICIENT P-Base Vertical

3600 1800

180 180

3600

10

HIGH EFFICIENT Definite Purpose

1.5 1.5

89.5 89.5

10

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

List Price $

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Hazardous Duty Motors

Introduction

Hazardous Duty Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Frame

Voltage

Type

Part Number

Multiplier FL Symbol Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

Stock/Modifiable

List Multiplier Price $ Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model ✔

Horizontal, Foot Mounted - continued

40

3600

324TS

460

RGZZESD

Ball

1MJ03242XE42

3637

SA-7XXP

45

93.6

589

✔

125 3600

444TS

460

RGZZESD

Ball

40

3600

324TS

575

RGZZESD

Ball

1MJ03242XE52

3637

SA-7XXP

36

93.6

589

✔

125 3600

444TS

575

RGZZESD

Ball

40

1800

324T

460

RGZZESD

Ball

1MJ03244XE41

3510

SA-7XXP

47

93.6

589

✔

125 1800

444TS

460

RGZZESD

Ball

40

1800

324T

575

RGZZESD

Ball

1MJ03244XE51

3510

SA-7XXP

37.6

93.6

589

✔

125 1800

444T

460

RGZZESD

Roller

40

1200

364T

460

RGZZESD

Ball

1MJ03646XE41

5812

SA-7XXP

52

93.6

865

✔

125 1800

444TS

575

RGZZESD

Ball

40

1200

364T

575

RGZZESD

Ball

1MJ03646XE51

5812

SA-7XXP

41.6

93.6

865

✔

125 1800

444T

575

RGZZESD

Roller

40

900

365T

460

RGZZESD

Ball

7698

SA-7XXP

63

91.7

915

125 1200

445T

460

RGZZESD

Roller

40

900

365T

575

RGZZESD

Ball

7698

SA-7XXP

50.4

91.7

915

125 1200

445T

575

RGZZESD

Roller

50

3600

326TS

460

RGZZESD

Ball

1MJ03262XE42

4521

SA-7XXP

55

93.6

738

✔

125

900

447T

460

RGZZESD

Roller

18056

SA-7XXP

152

93.6

2450

50

3600

326TS

575

RGZZESD

Ball

1MJ03262XE52

4521

SA-7XXP

44

93.6

738

✔

125

900

447T

575

RGZZESD

Roller

18056

SA-7XXP

121.6

93.6

2450

50

1800

326T

460

RGZZESD

Ball

1MJ03264XE41

4167

SA-7XXP

58

93.6

645

✔

150 3600

445TS

460

RGZZESD

Ball

14940

SA-7XXP

164

95

1900

50

1800

326T

575

RGZZESD

Ball

1MJ03264XE51

4167

SA-7XXP

46.4

93.6

645

✔

150 3600

445TS

575

RGZZESD

Ball

14940

SA-7XXP

131.2

95

1900

50

1200

365T

460

RGZZESD

Ball

1MJ03656XE41

6542

SA-7XXP

66

93.6

915

✔

150 1800

445TS

460

RGZZESD

Ball

1MJ04454XE42

13578

SA-7XXP

170

95.8

1900

✔

50

1200

365T

575

RGZZESD

Ball

1MJ03656XE51

6542

SA-7XXP

52.8

93.6

915

✔

150 1800

445T

460

RGZZESD

Roller

1MJ04454XE41

13578

SA-7XXP

170

95.8

1900

✔

50

900

404T

460

RGZZESD

Ball

9340

SA-7XXP

67

91.7

1230

150 1800

445TS

575

RGZZESD

Ball

13578

SA-7XXP

136

95.8

1900

1MJ04442XE42

12674

SA-7XXP

138

94.5

1700

12674

SA-7XXP

110.4

94.5

1700

1MJ04444XE42

11878

SA-7XXP

143

95

1700

✔

1MJ04444XE41

11878

SA-7XXP

143

95

1700

✔

11878

SA-7XXP

114.4

95

1700

11878

SA-7XXP

114.4

95

1700

14614

SA-7XXP

144

94.5

1900

14614

SA-7XXP

115.2

94.5

1900

1MJ04456XE41

1MJ04452XE42

900

404T

575

RGZZESD

Ball

9340

SA-7XXP

53.6

91.7

1230

150 1800

445T

575

RGZZESD

Roller

3600

364TS

460

RGZZESD

Ball

1MJ03642XE42

5911

SA-7XXP

68

93.6

865

✔

150 1200

447T

460

RGZZESD

Roller

60

3600

364TS

575

RGZZESD

Ball

1MJ03642XE52

5911

SA-7XXP

54.4

93.6

865

✔

150 1200

447T

575

RGZZESD

Roller

60

1800

364T

460

RGZZESD

Ball

1MJ03644XE41

5867

SA-7XXP

71

93.6

865

✔

150

900

449T

460

RGZZESD

Roller

22503

SA-7XXP

186

94.1

2535

60

1800

364T

575

RGZZESD

Ball

1MJ03644XE51

5867

SA-7XXP

56.8

93.6

865

✔

150

900

449T

575

RGZZESD

Roller

22503

SA-7XXP

148.8

94.1

2535

60

1200

404T

460

RGZZESD

Ball

1MJ04046XE41

7826

SA-7XXP

74

94.1

1230

✔

200 3600

447TS

460

RGZZESD

Ball

60

1200

404T

575

RGZZESD

Ball

1MJ04046XE51

7826

SA-7XXP

59.2

94.1

1230

✔

200 3600

447TS

575

RGZZESD

Ball

60

900

405T

460

RGZZESD

Ball

10514

SA-7XXP

78

91.7

1335

200 1800

447TS

460

RGZZESD

Ball

60

900

405T

575

RGZZESD

Ball

10514

SA-7XXP

62.4

91.7

1335

200 1800

447T

460

RGZZESD

Roller

75

3600

365TS

460

RGZZESD

Ball

1MJ03652XE42

7220

SA-7XXP

85

94.1

915

✔

200 1800

447TS

575

RGZZESD

Ball

75

3600

365TS

575

RGZZESD

Ball

1MJ03652XE52

7220

SA-7XXP

68

94.1

915

✔

200 1800

447T

575

RGZZESD

Roller

75

1800

365T

460

RGZZESD

Ball

1MJ03654XE41

7225

SA-7XXP

87

94.1

915

✔

200 1200

449T

460

RGZZESD

Roller

75

1800

365T

575

RGZZESD

Ball

1MJ03654XE51

7225

SA-7XXP

69.6

94.1

915

✔

200 1200

449T

575

RGZZESD

75

1200

405T

460

RGZZESD

Ball

1MJ04056XE41

9003

SA-7XXP

93

94.5

1335

✔

200

900

449T

460

75

1200

405T

575

RGZZESD

Ball

1MJ04056XE51

9003

SA-7XXP

74.4

94.5

1335

✔

200

900

449T

575

75

900

444T

460

RGZZESD

Roller

13836

SA-7XXP

94

93

1700

250 3600

449TS

460

RGZZESD

Ball

22381

SA-7XXP

267

95.4

2535

75

900

444T

575

RGZZESD

Roller

13836

SA-7XXP

75.2

93

1700

250 3600

449TS

575

RGZZESD

Ball

22381

SA-7XXP

213.6

95.4

2535

405TS

460

RGZZESD

Ball

405TS

575

RGZZESD

Ball

1MJ04052XE42

9701

SA-7XXP

9701

SA-7XXP

405T

460

RGZZESD

Ball

1MJ04054XE41

9036

SA-7XXP

405T

575

RGZZESD

Ball

1MJ04054XE51

9036

SA-7XXP

100 1200

444T

460

RGZZESD

Roller

1MJ04446XE41

12089

SA-7XXP

100 1200

444T

575

RGZZESD

Roller

12089

SA-7XXP

100

900

445T

460

RGZZESD

Roller

16772

SA-7XXP

100

900

445T

575

RGZZESD

Roller

16772

SA-7XXP

86.4 113 90.4 117 93.6 123 98.4

94.1

1335

94.1

1335

✔

95.8

1900

170

95

2450

16171

SA-7XXP

136

95

2450

✔

✔

18801

SA-7XXP

216

95

2450

18801

SA-7XXP

172.8

95

2450

1MJ04474XE42

16486

SA-7XXP

225

95.8

2450

✔

1MJ04474XE41

16486

SA-7XXP

225

95.8

2450

✔

16486

SA-7XXP

180

95.8

2450

16486

SA-7XXP

180

95.8

2450

19005

SA-7XXP

226

95

2535

Roller

19005

SA-7XXP

180.8

95

2535

RGZZESD

Roller

23829

SA-7XXP

241

94.5

2535

RGZZESD

Roller

23829

SA-7XXP

192.8

94.5

2535

1MJ04496XE41

250 1800

449TS

460

RGZZESD

Ball

19289

SA-7XXP

281

95.8

2535

250 1800

449TS

575

RGZZESD

Ball

19289

SA-7XXP

224.8

95.8

2535

94.5

1335

✔

250 1200

449TS

460

RGZZESD

Ball

22615

SA-7XXP

280

95

2535

1335

✔

250 1200

449TS

575

RGZZESD

Ball

22615

SA-7XXP

224

95

2535

94.5

1700

✔

300 3600

449TS

460

RGZZESD

Ball

29100

SA-7XXP

323

95.8

2535

94.5

1700

300 3600

449TS

575

RGZZESD

Ball

29100

SA-7XXP

258.4

95.8

2535

94.1

1900

300 1800

449TS

460

RGZZESD

Ball

21928

SA-7XXP

346

95.4

2535

94.1

1900

300 1800

449TS

575

RGZZESD

Ball

21928

SA-7XXP

276.8

95.4

2535

✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-43

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

136

SA-7XXP

94.5

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2-42

SA-7XXP

16171

NEMA PREMIUM General Purpose

100 1800 100 1800

108

1MJ04472XE42

13578

HIGH EFFICIENT P-Base Vertical

100 3600 100 3600

1MJ04476XE41

✔

HIGH EFFICIENT Definite Purpose

50 60

✔

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

RPM

List Price $

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Hazardous Duty Motors

Introduction

Hazardous Duty Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Frame

Voltage

Type

Part Number

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Vertical with Drip Cover, Footless 1

1800 143TCV

230/460

RGZZVESD

Ball

1MJ91444YP62

697

SA-7XXP

1.5

82.5

60

✔

1

1200 145TCV

230/460

RGZZVESD

Ball

1MJ91456YP62

785

SA-7XXP

1.8

80

80

✔

These high efficiency explosion-proof motors are UL® listed for hazardous gas environments, and are suitable for use in Class I, Groups C & D, Division 1 hazardous areas. They are ideal for use in applications such as chemical processing, mining, foundry, pulp and paper, waste management, and petro/chemical.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Performance Specifications

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Two series-connected normally-closed Class B thermostats are supplied as standard.

230/460

RGZZVESD

Ball

1MJ91828YP62

1315

SA-7XXP

1.9

78.5

130

✔

230/460

RGZZVESD

Ball

1MJ91442YP62

722

SA-7XXP

2

82.5

70

✔

1.5

1800 145TCV

230/460

RGZZVESD

Ball

1MJ91454YP62

737

SA-7XXP

2.2

84

80

✔

1.5

1200 182TCV

230/460

RGZZVESD

Ball

1MJ91826YP62

845

SA-7XXP

2.3

85.5

130

✔

1.5

900 184TCV

230/460

RGZZVESD

Ball

1MJ91848YP62

1522

SA-7XXP

2.6

80

135

✔

2

3600 145TCV

230/460

RGZZVESD

Ball

1MJ91452YP62

800

SA-7XXP

2.5

84

72

✔

2

1800 145TCV

230/460

RGZZVESD

Ball

1MJ91464YP62

778

SA-7XXP

2.9

84

80

✔

2

1200 184TCV

230/460

RGZZVESD

Ball

1MJ91846YP62

934

SA-7XXP

3

86.5

135

✔

2

900 213TCV

230/460

RGZZVESD

Ball

1MJ92138YP62

1794

SA-7XXP

3.3

82.5

175

✔

3

3600 182TCV

230/460

RGZZVESD

Ball

1MJ91822YP62

860

SA-7XXP

3.6

86.5

130

✔

3

1800 182TCV

230/460

RGZZVESD

Ball

1MJ91824YP62

857

SA-7XXP

3.9

87.5

130

✔

3

1200 213TCV

230/460

RGZZVESD

Ball

1MJ92136YP62

1105

SA-7XXP

4

87.5

175

✔

3

900 215TCV

230/460

RGZZVESD

Ball

1MJ92158YP62

2125

SA-7XXP

4.7

84

195

✔

5

3600 184TCV

230/460

RGZZVESD

Ball

1MJ91842YP62

1016

SA-7XXP

5.8

87.5

135

✔

5

1800 184TCV

230/460

RGZZVESD

Ball

1MJ91844YP62

941

SA-7XXP

6.5

87.5

135

✔

5

1200 215TCV

230/460

RGZZVESD

Ball

1MJ92156YP62

1392

SA-7XXP

6.8

88.5

195

✔

5

900 254TCV

230/460

RGZZVESD

Ball

1MJ92548YP62

2266

SA-7XXP

7.5

86.5

295

✔

Features for Long Life

7.5

3600 213TCV

230/460

RGZZVESD

Ball

1MJ92132YP62

1196

SA-7XXP

8.8

88.5

175

✔

7.5

1800 213TCV

230/460

RGZZVESD

Ball

1MJ92134YP62

1191

SA-7XXP

9.5

89.5

175

✔

7.5

1200 254TCV

230/460

RGZZVESD

Ball

1MJ92546YP62

1816

SA-7XXP

9.8

90.2

295

✔

7.5

900 256TCV

230/460

RGZZVESD

Ball

1MJ92568YP62

2731

SA-7XXP

12

87.5

365

✔

10

3600 215TCV

230/460

RGZZVESD

Ball

1MJ92152YP62

1331

SA-7XXP

12

89.5

195

✔

Frame and End Shields – Cast iron frame and end shields for exceptional structural integrity, with sintered condensation drains on 404T – 449T frames. Lifting eyebolts are included for frames 213T to 449T.

10

1800 215TCV

230/460

RGZZVESD

Ball

1MJ92154YP62

1354

SA-7XXP

13

89.5

195

✔

10

1200 256TCV

230/460

RGZZVESD

Ball

1MJ92566YP62

2108

SA-7XXP

13

90.2

365

✔

15

3600 254TCV

230/460

RGZZVESD

Ball

1MJ92542YP62

1776

SA-7XXP

17

90.2

295

✔

1MJ92544YP62

✔

15

1800 254TCV

230/460

RGZZVESD

Ball

15

1200 284TCV

230/460

RGZZVESD

Ball

1753

SA-7XXP

19

91.7

295

2893

SA-7XXP

20

91

450

3600 256TCV

230/460

RGZZVESD

Ball

1MJ92562YP62

2081

SA-7XXP

23

90.2

365

✔

1800 256TCV

230/460

RGZZVESD

Ball

1MJ92564YP62

2062

SA-7XXP

26

91.7

365

✔

20

1200 286TCV

230/460

RGZZVESD

Ball

3360

SA-7XXP

26

91.7

525

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, oversized single shielded bearings with cast iron inner caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Frames 143T – 256T are equipped with a shaft seal on the drive end; 284T – 449T frames have a drive end V-ring slinger for added bearing life.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

HIGH EFFICIENT P-Base Vertical

20 20

•1 to 300 HP •1.0 service factor, 40ºC ambient •T3C temperature code •900, 1200, 1800, or 3600 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143T through 449T frame

HIGH EFFICIENT Definite Purpose

900 182TCV 3600 143TCV

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-44

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-45

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Hazardous Duty

1 1.5

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RPM

Multiplier Symbol

Class I, Groups C & D, Division 1 RGZZESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

HP

List Price $

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Hazardous Duty Motors

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESD DE Bearing

Introduction

Hazardous Duty Motors

Introduction HIGH EFFICIENT General Purpose

HP

HIGH EFFICIENT Multi Speed

Part Number

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

5189

SA-7MXP

55

93.6

738

4835

SA-7MXP

58

93.6

645

SA-7MXP

66

93.6

915

Horizontal, Foot Mounted - continued

1

1800

143T

230/460

RGZZESD

Ball

774

SA-7MXP

1.5

82.5

60

50

3600

326TS

460

RGZZESD

Ball

1

1200

145T

230/460

RGZZESD

Ball

863

SA-7MXP

1.8

80

70

50

1800

326T

460

RGZZESD

Ball

1

900

182T

230/460

RGZZESD

Ball

1392

SA-7MXP

1.9

78.5

113

50

1200

365T

460

RGZZESD

Ball

7414

1.5

3600

143T

230/460

RGZZESD

Ball

800

SA-7MXP

2

82.5

60

50

900

404T

460

RGZZESD

Ball

10742

SA-7MXP

67

91.7

1230

70

60

3600

364TS

460

RGZZESD

Ball

6783

SA-7MXP

68

93.6

865

100

60

1800

364T

460

RGZZESD

Ball

6739

SA-7MXP

71

93.6

865

60

1200

404T

460

RGZZESD

Ball

9453

SA-7MXP

74

94.1

1230

1.5 1.5

1800 1200

145T 182T

230/460 230/460

RGZZESD RGZZESD

Ball

1MJ01444XC21

1MJ01454XC21

Ball

815 922

SA-7MXP SA-7MXP

2.2 2.3

84 85.5

✔

✔

1MJ03264XC41

1MJ03644XC41

1.5

900

184T

230/460

RGZZESD

Ball

1599

SA-7MXP

2.6

80

117

2

3600

145T

230/460

RGZZESD

Ball

877

SA-7MXP

2.5

84

70

60

900

405T

460

RGZZESD

Ball

12722

SA-7MXP

78

91.7

1335

70

75

3600

365TS

460

RGZZESD

Ball

8092

SA-7MXP

85

94.1

915

120

75

1800

365T

460

RGZZESD

Ball

8097

SA-7MXP

87

94.1

915

75

1200

405T

460

RGZZESD

Ball

10629

SA-7MXP

93

94.5

1335

75

1800 1200

145T 184T

230/460 230/460

RGZZESD RGZZESD

Ball

1MJ01464XC21

Ball

856 1012

SA-7MXP SA-7MXP

2.9 3

84 86.5

2

900

213T

230/460

RGZZESD

Ball

1907

SA-7MXP

3.3

82.5

153

3

3600

182T

230/460

RGZZESD

Ball

937

SA-7MXP

3.6

86.5

100

3

1800

182T

230/460

RGZZESD

Ball

934

SA-7MXP

3.9

87.5

100

3

1200

213T

230/460

RGZZESD

Ball

1218

SA-7MXP

4

87.5

3

900

215T

230/460

RGZZESD

Ball

2238

SA-7MXP

4.7

5

3600

184T

230/460

RGZZESD

Ball

1093

SA-7MXP

5

1800

184T

230/460

RGZZESD

Ball

1019

SA-7MXP

5

1200

215T

230/460

RGZZESD

Ball

1506

5

900

254T

230/460

RGZZESD

Ball

2391

7.5

3600

213T

230/460

RGZZESD

1MJ01824XC21

1MJ01844XC21

Ball

7.5

1800

213T

230/460

RGZZESD

Ball

7.5

1200

254T

230/460

RGZZESD

Ball

1310 1MJ02134XC21

✔

1MJ03654XC41

900

444TS

460

RGZZESD

Ball

16327

SA-7MXP

94

93

1700

100 3600

405TS

460

RGZZESD

Ball

11328

SA-7MXP

108

94.1

1335

160

100 1800

405T

460

RGZZESD

Ball

10663

SA-7MXP

113

94.5

1335

84

171

100 1200

444TS

460

RGZZESD

Ball

13930

SA-7MXP

117

94.5

1700

5.8

87.5

120

100

1900

6.5

87.5

115

SA-7MXP

6.8

88.5

SA-7MXP

7.5

86.5

SA-7MXP

8.8

88.5

✔

1MJ04054XC41

900

445TS

460

RGZZESD

Ball

19287

SA-7MXP

123

94.1

125 3600

444TS

460

RGZZESD

Ball

14515

SA-7MXP

138

94.5

1700

180

125 1800

444TS

460

RGZZESD

Ball

13719

SA-7MXP

143

95

1700

292

125 1200

445TS

460

RGZZESD

Ball

16366

SA-7MXP

144

94.5

1900

160

125

900

447TS

460

RGZZESD

Ball

20764

SA-7MXP

152

93.6

2450

150 3600

445TS

460

RGZZESD

Ball

16781

SA-7MXP

164

95

1900

✔

✔

1305

SA-7MXP

9.5

89.5

160

1940

SA-7MXP

9.8

90.2

265

150 1800

445TS

460

RGZZESD

Ball

15419

SA-7MXP

170

95.8

1900

447TS

460

RGZZESD

Ball

18479

SA-7MXP

170

95

2450

900

256T

230/460

RGZZESD

Ball

2855

SA-7MXP

12

87.5

324

10

3600

215T

230/460

RGZZESD

Ball

1444

SA-7MXP

12

89.5

180

150

900

449TS

460

RGZZESD

Ball

25878

SA-7MXP

186

94.1

2535

200 3600

447TS

460

RGZZESD

Ball

21432

SA-7MXP

216

95

2450

1MJ02154XC21

✔

1800

215T

230/460

RGZZESD

Ball

1467

SA-7MXP

13

89.5

180

10

1200

256T

230/460

RGZZESD

Ball

2233

SA-7MXP

13

90.2

325

200 1800

447TS

460

RGZZESD

Ball

18795

SA-7MXP

225

95.8

2450

10

900

284T

230/460

RGZZESD

Ball

3687

SA-7MXP

15

91

410

200 1200

449TS

460

RGZZESD

Ball

21665

SA-7MXP

226

95

2535

15

3600

254T

230/460

RGZZESD

Ball

1900

SA-7MXP

17

90.2

265

200

15

1800

254T

230/460

RGZZESD

Ball

1878

SA-7MXP

19

91.7

265

15

1200

284T

230/460

RGZZESD

Ball

3053

SA-7MXP

20

91

15

900

286T

230/460

RGZZESD

Ball

4552

SA-7MXP

23

20

3600

256T

230/460

RGZZESD

Ball

2205

SA-7MXP

20

1800

256T

230/460

RGZZESD

Ball

2187

SA-7MXP

20

1200

286T

230/460

RGZZESD

Ball

3520

SA-7MXP

20

900

324T

230/460

RGZZESD

Ball

5545

SA-7MXP

25

3600

284TS

460

RGZZESD

Ball

2867

SA-7MXP

25

1800

284T

460

RGZZESD

Ball

2780

25

1200

324T

460

RGZZESD

Ball

4456

25

900

326T

460

RGZZESD

Ball

30

3600

286TS

460

RGZZESD

Ball

30

1800

286T

460

RGZZESD

Ball

30

1200

326T

460

RGZZESD

30

900

364T

460

40

3600

324TS

460

40

1800

324T

460

RGZZESD

Ball

40

1200

364T

460

RGZZESD

Ball

40

900

365T

460

RGZZESD

Ball

8853

900

449TS

460

RGZZESD

Ball

27166

SA-7MXP

241

94.5

2535

250 3600

449TS

460

RGZZESD

Ball

25514

SA-7MXP

267

95.4

2535

410

250 1800

449TS

460

RGZZESD

Ball

21990

SA-7MXP

281

95.8

2535

91

460

250 1200

449TS

460

RGZZESD

Ball

25782

SA-7MXP

280

95

2535

23

90.2

325

300 3600

449TS

460

RGZZESD

Ball

33173

SA-7MXP

323

95.8

2535

26

91.7

325

300 1800

449TS

460

RGZZESD

Ball

24998

SA-7MXP

346

95.4

2535

26

91.7

460

31

91

589

29

91.7

410

SA-7MXP

29

93

410

SA-7MXP

33

92.4

589

6437

SA-7MXP

38

90.2

645

3195

SA-7MXP

34

91.7

460

3082

SA-7MXP

35

93

460

Ball

4936

SA-7MXP

39

92.4

645

RGZZESD

Ball

7544

SA-7MXP

47

91

865

RGZZESD

Ball

4305

SA-7MXP

45

93.6

589

4178

SA-7MXP

47

93.6

589

6684

SA-7MXP

52

93.6

865

SA-7MXP

63

91.7

915

1MJ02544XC21

1MJ02564XC21

1MJ02844XC41

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

✔

✔

✔

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

2-47

NEMA PREMIUM Severe Duty

1MJ03244XC41

✔

✔

NEMA PREMIUM General Purpose

1MJ02864XC41

✔

✔

HIGH EFFICIENT P-Base Vertical

10

✔

HIGH EFFICIENT Definite Purpose

7.5

150 1200

2-46

Stock Model

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

Type

FL Amps 460V

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Definite Purpose

Voltage

Multiplier Symbol

Class I, Groups C & D, Division 1 RGZZESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT P-Base Vertical

Frame

List Price $

Horizontal, Foot Mounted

2

NEMA PREMIUM General Purpose

RPM

DE Bearing

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Severe Duty

Class I, Groups C & D, Division 1 RGZZESD

2

NEMA PREMIUM Severe Duty

Hazardous Duty Motors

Introduction

Hazardous Duty Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Automotive Duty TEFC motors are approved for use by major U.S. automobile manufacturers. They meet or exceed the requirements per GM7EH, GM7EQ, Ford EM 1, and Chrysler NPEM 100 and previous NEMA U-Frame motor standards. These motors are ideal for applications where automotive approved motors are required, such as pump, fan, compressor, conveyor and other constant speed applications.

Performance Specifications

Features for Long Life

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 182U-256U frames have a drive end shaft seal and 284U-445U frames have a drive end shaft V-ring slinger.

Type

Part Number

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

1

1800

182

460

RGZEAD

Ball

1LA91824YK701AD

379

SA-7AE

1.4

85.5

85

✔

1

1200

184

460

RGZEAD

Ball

1LA91846YK701AD

463

SA-7AE

1.6

81.5

100

✔

1.5

3600

182

460

RGZEAD

Ball

1LA91822YK701AD

438

SA-7AE

1.9

82.5

85

✔

1.5

1800

184

460

RGZEAD

Ball

1LA91844YK701AD

406

SA-7AE

2

86.5

100

✔

1.5

1200

184

460

RGZEAD

Ball

1LA91856YK701AD

511

SA-7AE

2.3

85.5

100

✔

2

3600

184

460

RGZEAD

Ball

1LA91842YK701AD

485

SA-7AE

2.5

84

100

✔ ✔

2

1800

184

460

RGZEAD

Ball

1LA91854YK701AD

428

SA-7AE

2.5

87.5

100

2

1200

213

460

RGZEAD

Ball

1LA92136YK701AD

566

SA-7AE

2.8

86.5

130

✔

3

3600

184

460

RGZEAD

Ball

1LA91852YK701AD

549

SA-7AE

3.7

86.5

100

✔

3

1800

213

460

RGZEAD

Ball

1LA92134YK701AD

492

SA-7AE

4

87.5

130

✔

3

1200

215

460

RGZEAD

Ball

1LA92156YK701AD

701

SA-7AE

4.1

87.5

162

✔

5

3600

213

460

RGZEAD

Ball

1LA92132YK701AD

652

SA-7AE

6

87.5

130

✔

5

1800

215

460

RGZEAD

Ball

1LA92154YK701AD

652

SA-7AE

6.3

88.5

162

✔

5

1200

254U

460

RGZEAD

Ball

1LA92546YK701AD

975

SA-7AE

6.6

89.5

250

✔

7.5

3600

215

460

RGZEAD

Ball

1LA92152YK701AD

770

SA-7AE

8.7

88.5

162

✔

7.5

1800

254U

460

RGZEAD

Ball

1LA92544YK701AD

857

SA-7AE

9.5

89.5

250

✔

7.5

1200

256U

460

RGZEAD

Ball

1LA92566YK701AD

1246

SA-7AE

9.8

90.2

296

✔

10

3600

254U

460

RGZEAD

Ball

1LA92542YK701AD

923

SA-7AE

11

89.5

250

✔

10

1800

256U

460

RGZEAD

Ball

1LA92564YK701AD

1041

SA-7AE

12

89.5

296

✔

10

1200

284U

460

RGZEAD

Ball

1LA02846AE41

1527

SA-7AE

13

90.2

375

✔

15

3600

256U

460

RGZEAD

Ball

1LA92562YK701AD

1175

SA-7AE

17

90.5

296

✔

15

1800

284U

460

RGZEAD

Ball

1LA02844AE41

1430

SA-7AE

18

91.7

375

✔

15

1200

324U

460

RGZEAD

Ball

1LA03246AE41

2056

SA-7AE

19

91

565

✔

20

3600

286U

460

RGZEAD

Ball

1LA02862AE41

1598

SA-7AE

23.5

92.4

430

✔

20

1800

286U

460

RGZEAD

Ball

1LA02864AE41

1756

SA-7AE

25

91.7

430

✔

20

1200

326U

460

RGZEAD

Ball

1LA03266AE41

2513

SA-7AE

26

91.7

600

✔

25

3600

324S

460

RGZEAD

Ball

2051

SA-7AE

25

1800

324U

460

RGZEAD

Ball

1LA03244AE41

2198

SA-7AE

29

93

565

✔

1LA03646AE41

3034

SA-7AE

33

92.4

800

✔

2473

SA-7AE

25

1200

364U

460

RGZEAD

Ball

30

3600

326S

460

RGZEAD

Ball

565

600

30

1800

326U

460

RGZEAD

Ball

1LA03264AE41

2568

SA-7AE

34

93

600

✔

30

1200

365U

460

RGZEAD

Ball

1LA03656AE41

3433

SA-7AE

39

92.4

875

✔

40

3600

364US

460

RGZEAD

Ball

3228

SA-7AE

40

1800

364U

460

RGZEAD

Ball

1LA03644AE41

3386

SA-7AE

46

93.6

800

40

1200

404U

460

RGZEAD

Ball

4407

SA-7AE

50

3600

365US

460

RGZEAD

Ball

50

1800

365U

460

RGZEAD

Ball

50

1200

405U

460

RGZEAD

Ball

60

3600

405US

460

RGZEAD

Ball

60

1800

405U

460

RGZEAD

Ball

60

1200

444U

460

RGZEAD

Roller

75

3600

444US

460

RGZEAD

Ball

75

1800

444U

460

RGZEAD

Roller

75

1200

1LA03654AE41

1LA04054AE41

1LA04444AE41

4075

SA-7AE

3972

SA-7AE

5091

SA-7AE

4848

SA-7AE

4932

SA-7AE

5976

SA-7AE

6369

SA-7AE

6083

SA-7AE

445U

460

RGZEAD

Roller

7087

SA-7AE

100 3600

445US

460

RGZEAD

Ball

8418

SA-7AE

100 1800

445U

460

RGZEAD

Roller

7561

SA-7AE

1LA04454AE41

800 ✔

1135 875 57

93.6

875

✔

1300 1300 68

94.1

1300

✔

1625 1625 89

94.1

1625

✔

1900 1900 114

94.5

1900

✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

2-48

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-49

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Voltage

FL Amps 460V

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion.

Frame

Multiplier Symbol

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

RPM

List Price $

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213U to 445U.

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HP

DE Bearing

HIGH EFFICIENT Hazardous Duty

•1 to 100 HP •1.15 service factor, 40ºC ambient •1.0 service factor, 65ºC ambient •3600, 1800 or 1200 RPM •3 phase, 60 Hz; 460 volt; 200, 230 & 575 volt available •Meets or exceeds NEMA Energy Efficiency standards •Class F insulation, Class B temperature rise •NEMA Design B, Continuous Duty •182U through 445U frame

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RGZEAD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

RGZEAD

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Automotive Duty - TEFC U-Frame Motors

Introduction

Automotive Duty - TEFC U-Frame Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

High efficiency severe duty brake motors are designed for severe operating environments. Brakes are spring-set and electrically released, with either a manually adjustable or selfadjusting design. In addition to foot mounting, Siemens brake motors are also available with C-face or D-flange construction.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Performance Specifications

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

Features for Long Life

Part Number 1LA01444SB21

FL Nom. Weight Eff. (%) (lbs.)

1

1800

143T

230/460

RGZESDB

Ball

1225

SA-7BR

6

1.5

82.5

87

1

1200

145T

230/460

RGZESDB

Ball

1230

SA-7BR

6

1.8

80

97

1

900

182T

230/460

RGZESDB

Ball

1257

SA-7BR

10

1.9

78.5

127

1.5

3600

143T

230/460

RGZESDB

Ball

1220

SA-7BR

6

2

82.5

87

1.5

1800

145T

230/460

RGZESDB

Ball

1265

SA-7BR

6

2.2

84

97

1.5

1200

182T

230/460

RGZESDB

Ball

1265

SA-7BR

10

2.3

85.5

127

1.5

900

184T

230/460

RGZESDB

Ball

1455

SA-7BR

15

2.6

80

143

2

3600

145T

230/460

RGZESDB

Ball

1350

SA-7BR

6

2.5

84

97

2

1800

145T

230/460

RGZESDB

Ball

1290

SA-7BR

10

2.9

84

97

2

1200

184T

230/460

RGZESDB

Ball

1385

SA-7BR

15

3

86.5

1LA01454SB21

1LA01464SB21

2

900

213T

230/460

RGZESDB

Ball

1917

SA-7BR

25

3.3

82.5

173

3600

182T

230/460

RGZESDB

Ball

1400

SA-7BR

10

3.6

86.5

127

3

1800

182T

230/460

RGZESDB

Ball

3

1200

213T

230/460

RGZESDB

Ball

1320

SA-7BR

15

3.9

87.5

128

1561

SA-7BR

25

4

87.5

173

3

900

215T

230/460

RGZESDB

Ball

2176

SA-7BR

25

4.7

84

205

5

3600

184T

230/460

RGZESDB

Ball

1525

SA-7BR

10

5.8

87.5

142

5

1800

184T

230/460

RGZESDB

Ball

1343

SA-7BR

20

6.5

87.5

143

5

1200

215T

230/460

RGZESDB

Ball

1933

SA-7BR

35

6.8

88.5

208

1LA01844SB21

5

900

254T

230/460

RGZESDB

Ball

3055

SA-7BR

50

7.5

86.5

292

7.5

3600

213T

230/460

RGZESDB

Ball

1566

SA-7BR

15

8.8

88.5

173

7.5

1800

213T

230/460

RGZESDB

Ball

1736

SA-7BR

35

9.5

89.5

176

7.5

1200

254T

230/460

RGZESDB

Ball

2613

SA-7BR

50

9.8

90.2

292

7.5

900

256T

230/460

RGZESDB

Ball

3870

SA-7BR

75

12

87.5

345

10

3600

215T

230/460

RGZESDB

Ball

1783

SA-7BR

25

12

89.5

205

10

1800

215T

230/460

RGZESDB

Ball

10

1200

256T

230/460

RGZESDB

Ball

1LA02134SB21

1LA02154SB21

2080

SA-7BR

50

13

89.5

204

3260

SA-7BR

75

13

90.2

345 434

10

900

284T

230/460

RGZESDB

Ball

4767

SA-7BR

105

15

91

15

3600

254T

230/460

RGZESDB

Ball

2387

SA-7BR

35

17

90.2

296

15

1800

254T

230/460

RGZESDB

Ball

2912

SA-7BR

75

19

91.7

300

15

1200

284T

230/460

RGZESDB

Ball

4306

SA-7BR

105

20

91

434 614

1LA02544SB21

15

900

286T

230/460

RGZESDB

Ball

7223

SA-7BR

125

23

91

20

3600

256T

230/460

RGZESDB

Ball

2873

SA-7BR

50

23

90.2

337

20

1800

256T

230/460

RGZESDB

Ball

3625

SA-7BR

105

26

91.7

349

20

1200

286T

230/460

RGZESDB

Ball

6449

SA-7BR

125

26

91.7

614

20

900

324T

230/460

RGZESDB

Ball

8288

SA-7BR

175

31

91

729

25

3600

284TS

460

RGZESDB

Ball

25

1800

284T

460

RGZESDB

Ball

25

1200

324T

460

RGZESDB

Ball

1LA02564SB21

1LA02844SB21

3719

SA-7BR

75

29

91.7

430

4038

SA-7BR

105

29

93

434

7316

SA-7BR

175

33

92.4

729 810

25

900

326T

460

RGZESDB

Ball

9300

SA-7BR

230

38

90.2

30

3600

286TS

460

RGZESDB

Ball

4040

SA-7BR

75

34

91.7

500

30

1800

286T

460

RGZESDB

Ball

6020

SA-7BR

105

35

93

614

30

1200

326T

460

RGZESDB

Ball

8136

SA-7BR

230

39

92.4

810

30

900

364T

460

RGZESDB

Ball

13790

SA-7BR

330

47

91

40

3600

324TS

460

RGZESDB

Ball

5198

SA-7BR

105

45

93.6

619

40

1800

324T

460

RGZESDB

Ball

7043

SA-7BR

175

47

93.6

729

40

1200

364T

460

RGZESDB

Ball

13105

SA-7BR

330

52

93.6

1000

40

900

365T

460

RGZESDB

Ball

14850

SA-7BR

330

63

91.7

1020

1LA02864SB21

✔

✔

✔

143

3

1LA01824SB21

Stock Model

✔

✔

✔

✔

✔

✔

✔

✔

1000

Notes: 1. Standard brake - NEMA 4, 230/460V Coil Voltage, Single Phase. Other voltages available.

2-50

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-51

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Type

FL Amps 460V

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion.

Voltage

Multiplier Brake Symbol (lb-ft)

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-449T frames have a drive end shaft V-ring slinger.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

Frame

List Price $

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to 365T.

Cooling – A bi-directional, non-sparking fan is included on the shaft. Its lowinertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

RPM

DE Bearing

HIGH EFFICIENT Hazardous Duty

•1 to 75 HP* •1.15 service factor, 40ºC ambient •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Meets or exceeds NEMA Energy Efficiency standards •Class F insulation, Class B temperature rise •NEMA Design B, Continuous Duty •6 to 330 ft. lbs. brake torque* •143T through 365T frame * Contact Siemens for additional ratings

HP

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RGZESDB

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

RGZESDB

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Severe Duty - TEFC Brake Motors

Introduction

Severe Duty - TEFC Brake Motors

Introduction HIGH EFFICIENT General Purpose

Stock/Modifiable Part Number

List Price $

Multiplier Symbol

Brake (lb-ft)

RPM

Frame

Voltage

Type

50

3600

326TS

460

RGZESDB

Ball

6064

SA-7BR

105

55

93.6

50

1800

326T

460

RGZESDB

Ball

8037

SA-7BR

230

58

93.6

810

50

1200

365T

460

RGZESDB

Ball

13750

SA-7BR

330

66

93.6

1020

694

60

1800

364T

460

RGZESDB

Ball

12890

SA-7BR

330

71

93.6

1000

75

1800

365T

460

RGZESDB

Ball

14055

SA-7BR

330

87

94.1

1020

Notes: 1. Standard brake - NEMA 4, 230/460V Coil Voltage, Single Phase. Other voltages available.

Performance Specifications

Severe Duty - TEFC Brake Ready Motors HP

Stock/Modifiable Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

Brake (lb-ft)

FL Amps 460V

NEMA Design C motors are specially designed for applications that require high starting torques to break away standing loads such as reciprocating conveyors, crushers and mixers. These motors feature starting torques up to 280% with normal slip and low starting current. Their high efficiency and severe duty design makes them cost effective choices for a variety of applications that require rugged power.

FL Nom. Weight Eff. (%) (lbs.)

Stock Model

Frame

1 1800 1.5 1800

143T 145T

230/460 230/460

RGZESBR RGZESBR

Ball Ball

1LA01444BR21 1LA01454BR21

990 1035

SA-7BR SA-7BR

6 6

1.5 2.2

82.5 84

40 55

✔

2

1800

145T

230/460

RGZESBR

Ball

1LA01464BR21

1055

SA-7BR

10

2.9

84

77

✔

3

1800

182T

230/460

RGZESBR

Ball

1LA01824BR21

1100

SA-7BR

15

3.9

87.5

85

✔

5

1800

184T

230/460

RGZESBR

Ball

1LA01844BR21

1150

SA-7BR

20

6.5

87.5

100

✔

7.5 1800

213T

230/460

RGZESBR

Ball

1LA02134BR21

1440

SA-7BR

35

9.5

89.5

135

✔

✔

1800

215T

230/460

RGZESBR

Ball

1LA02154BR21

1575

SA-7BR

50

13

89.5

160

✔

15

1800

254T

230/460

RGZESBR

Ball

1LA02544BR21

2190

SA-7BR

75

19

91.7

245

✔

20

1800

256T

230/460

RGZESBR

Ball

1LA02564BR21

2490

SA-7BR

105

26

91.7

285

✔

25

1800

284T

230/460

RGZESBR

Ball

1LA02844BR21

2835

SA-7BR

105

29

93

375

✔

30

1800

286T

230/460

RGZESBR

Ball

1LA02864BR21

4230

SA-7BR

125

35

93

408

✔

Features for Long Life Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to 449TS.

HIGH EFFICIENT P-Base Vertical

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-449T frames have a drive end shaft V-ring slinger.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-52

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-53

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Definite Purpose

10

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HIGH EFFICIENT Hazardous Duty

RPM

•5 to 200 HP •1.15 service factor, 40ºC ambient •1800 or 1200 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Meets or exceeds NEMA Energy Efficiency standards •Class F insulation, Class B temperature rise •NEMA Design C, Continuous Duty •184T through 449TS frame

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

Stock Model

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

FL Nom. Weight Eff. (%) (lbs.)

HP

RGZESBR

HIGH EFFICIENT Definite Purpose

FL Amps 460V

RGZTESD

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Severe Duty

RGZESDB DE Bearing

Introduction

Severe Duty - TEFC Design C Motors

Severe Duty - TEFC Brake Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number 1LA01844ST21

List Price $

Multiplier Symbol

FL Amps 460V 6.5

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted 5

1800

184T

230/460

RGZTESD

Ball

5

1200

215T

230/460

RGZTESD

Ball

7.5

1800

213T

230/460

RGZTESD

Ball

7.5

1200

254T

230/460

RGZTESD

Ball

10

1800

215T

230/460

RGZTESD

Ball

10

1200

256T

230/460

RGZTESD

Ball

15

1800

254T

230/460

RGZTESD

Ball

15

1200

284T

230/460

RGZTESD

Ball

20

1800

256T

230/460

RGZTESD

Ball

20

1200

286T

230/460

RGZTESD

Ball

25

1800

284T

460

RGZTESD

Ball

25

1200

324T

460

RGZTESD

Ball

30

1800

286T

460

RGZTESD

Ball

30

1200

326T

460

RGZTESD

Ball

1800

324T

460

RGZTESD

Ball

1200

364T

460

RGZTESD

Ball

50

1800

326T

460

RGZTESD

Ball

50

1200

365T

460

RGZTESD

Ball

60

1800

364T

460

RGZTESD

Ball

60

1200

404T

460

RGZTESD

Ball

1800

365T

460

RGZTESD

Ball

1200

405T

460

RGZTESD

Ball

100 1800

405T

460

RGZTESD

Ball

100 1200

444TS

460

RGZTESD

Ball

125 1800

444TS

460

RGZTESD

Ball

125 1200

445TS

460

RGZTESD

Ball

150 1800

445TS

460

RGZTESD

150 1200

447TS

460

RGZTESD

200 1800

447TS

460

200 1200

449TS

460

SA-7XSD

855

SA-7XSD

1422

SA-7XSD

1030

SA-7XSD

1738

SA-7XSD

1LA02544ST21

1355

SA-7XSD

2306

SA-7XSD

1LA02564ST21

1690

SA-7XSD

2809

SA-7XSD

1LA02844ST41

2015

SA-7XSD

3406

SA-7XSD

1LA02864ST41

2340

SA-7XSD

3923

SA-7XSD

1LA03244ST41 1LA03264ST41 1LA03644ST41 1LA03654ST41

3110

SA-7XSD

5316

SA-7XSD

3815

SA-7XSD

6104

SA-7XSD

5475

SA-7XSD

7152

SA-7XSD

87.5

100

9.5

87.5

157

Performance Specifications ✔

245 12.5

87.5

160

✔

285 19

89.5

245

24

90.2

285

✔

375 ✔

450 29

93

375

35

93

450

✔

565 ✔

600 49

93

565

✔

831 59

93

600

✔

875 73

93

831

✔

1135

6940

SA-7XSD

8421

SA-7XSD

8570

SA-7XSD

11508

SA-7XSD

1625

11281

SA-7XSD

1625

14135

SA-7XSD

1900

Ball

13114

SA-7XSD

1900

Ball

15815

SA-7XSD

2280

RGZTESD

Ball

15951

SA-7XSD

2280

RGZTESD

Ball

19360

SA-7XSD

2600

1LA04054ST41

✔

160

91

93.6

875

✔

•1 to 250 HP •1.15 service factor, 40ºC ambient •Continuous thrust: – Up: 355 to 1,860 lbs. – Down: 380 to 2,800 lbs. •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143HP through 449HP frame

Features for Long Life Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end T-drain, drip cover and lifting lugs are included.

1300 114

94.5

1300

✔

Insulation – Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable ball bearings with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 1 year.

Lubrication – A specially formulated, high temperature tested, polyureabased grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprenegasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens vertical motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT Definite Purpose

75 75

1LA02154ST21

SA-7XSD

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Hazardous Duty

40 40

1LA02134ST21

630 1070

Siemens P-base vertical solid shaft motors are ideal for applications such as centrifugal and turbine pumps.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

Vertical Solid Shaft - Normal Thrust RGZVESD

Stock/Modifiable

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

RGZTESD

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Definite Purpose

Severe Duty - TEFC P-Base Motors

Introduction

Severe Duty - TEFC Design C Motors

HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

Notes: 1. 1-3HP available as custom build.

Specifications table begins on the next page

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-55

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-54

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Cont. Thrust 1 Yr. Life Min. Down (lbs) 355

Stock/Modifiable

Cont. Thrust 1 Yr. Life Min. Multiplier Symbol SA-7EN

FL Nom. Eff. (%) 82.5

HP 1

RPM 1800

Frame 143HP

Voltage 230/460

Type RGZVESD

1

1200

145HP

230/460

RGZVESD

445

415

678

SA-7EN

1.6

82.5

1

900

182HP

230/460

RGZVESD

495

465

1037

SA-7EN

1.9

77

1.5

3600

143HP

230/460

RGZVESD

295

275

643

SA-7EN

1.9

1.5

1800

145HP

230/460

RGZVESD

385

330

578

SA-7EN

1.5

1200

182HP

230/460

RGZVESD

550

510

802

SA-7EN

1.5

900

184HP

230/460

RGZVESD

615

570

1170

SA-7EN

2.6

78.5

2

3600

145HP

230/460

RGZVESD

295

275

678

SA-7EN

2.5

84

2

1800

145HP

230/460

RGZVESD

385

350

655

SA-7EN

2.7

84

2

1200

184HP

230/460

RGZVESD

550

510

923

SA-7EN

3

85.5

100

Part Number

List Price $ 500

FL Amps 460V 1.5

Up (lbs) 380

Weight Stock (lbs.) Model 70

Multiplier Symbol SA-7EN

FL Amps 460V 45

FL Nom. Eff. (%) 92.4

3428

SA-7EN

47

92.4

565 800

HP 40

RPM 3600

Frame 324HP

Voltage 460

Type RGZVESD

Up (lbs) 1205

75

40

1800

324HP

460

RGZVESD

1570

85

40

1200

364HP

460

RGZVESD

2075

1675

5725

SA-7EN

52

92.4

82.5

70

40

900

365HP

460

RGZVESD

2340

1840

7184

SA-7EN

63

90.2

875

2.2

84

75

50

3600

326HP

460

RGZVESD

1215

995

1LA03262NE4B

4268

SA-7EN

55

92.4

710

✔

2.3

84

85

50

1800

326HP

460

RGZVESD

1585

1275

1LA03264NE4B

4065

SA-7EN

58

92.4

710

✔

50

1200

365HP

460

RGZVESD

2095

1660

6750

SA-7EN

66

92.4

875

50

900

404HP

460

RGZVESD

2370

1810

8591

SA-7EN

67

90.2

1290

60

3600

364HP

460

RGZVESD

1410

1080

1LA03642NE4B

5432

SA-7EN

68

92.4

800

✔

60

1800

364HP

460

RGZVESD

1795

1435

1LA03644NE4B

5389

SA-7EN

71

92.4

800

✔

60

1200

404HP

460

RGZVESD

2155

1595

7697

SA-7EN

74

93

1290

60

900

405HP

460

RGZVESD

2410

1770

9742

SA-7EN

78

90.2

1420

75

3600

365HP

460

RGZVESD

1420

1070

1LA03652NE4B

6715

SA-7EN

85

93

875

✔

75

1800

365HP

460

RGZVESD

1815

1415

1LA03654NE4B

6720

SA-7EN

87

93

875

✔

75

1200

405HP

460

RGZVESD

2195

1555

9025

SA-7EN

93

93.6

75

900

444HP

460

RGZVESD

2495

1685

12777

SA-7EN

94

91.7

1740

100

3600

405HP

460

RGZVESD

1475

1015

1LA04052NE4B

8945

SA-7EN

108

93

1420

✔

100

1800

405HP

460

RGZVESD

1915

1315

1LA04054NE4B

8293

SA-7EN

113

93.6

1420

✔

100

1200

444HP

460

RGZVESD

2315

1435

12065

SA-7EN

117

93.6

1740

100 75 75

2

900

213HP

230/460

RGZVESD

615

570

1340

SA-7EN

3.3

81.5

135

3

3600

182HP

230/460

RGZVESD

365

340

1LA01822NE2B

890

SA-7EN

3.6

85.5

85

✔

3

1800

182HP

230/460

RGZVESD

480

430

1LA01824NE2B

785

SA-7EN

3.9

86.5

85

✔

3

1200

213HP

230/460

RGZVESD

785

725

1218

SA-7EN

4

86.5

135

3

900

215HP

230/460

RGZVESD

875

810

1685

SA-7EN

4.7

82.5

160

5

3600

184HP

230/460

RGZVESD

375

330

1LA01842NE2B

1248

SA-7EN

5.8

86.5

100

✔

5

1800

184HP

230/460

RGZVESD

485

425

1LA01844NE2B

1093

SA-7EN

6.5

86.5

100

✔

5

1200

215HP

230/460

RGZVESD

790

720

1715

SA-7EN

6.8

87.5

160

5

900

254HP

230/460

RGZVESD

885

805

2063

SA-7EN

7.5

85.5

245

7.5

3600

213HP

230/460

RGZVESD

525

475

1LA02132NE2B

1548

SA-7EN

8.8

87.5

135

✔

7.5

1800

213HP

230/460

RGZVESD

685

610

1LA02134NE2B

1498

SA-7EN

9.5

88.5

135

✔

Down (lbs) 1005

Part Number 1LA03242NE4B

List Price $ 3402

1290

1LA03244NE4B

Weight Stock (lbs.) Model 565 ✔

1420

900

445HP

460

RGZVESD

2565

1615

15655

SA-7EN

123

93

1930

125

1800

444HP

460

RGZVESD

1975

1255

10857

SA-7EN

143

94.1

1740

125

1200

445HP

460

RGZVESD

2385

1365

14585

SA-7EN

144

93.6

1930

125

900

447HP

460

RGZVESD

2670

1510

17985

SA-7EN

152

92.4

2280

150

1800

445HP

460

RGZVESD

2060

1170

12525

SA-7EN

170

94.5

1930

150

1200

447HP

460

RGZVESD

2400

1350

18125

SA-7EN

170

94.1

2280

1200

254HP

230/460

RGZVESD

1130

1025

2045

SA-7EN

9.8

88.5

245

900

256HP

230/460

RGZVESD

1260

1150

2505

SA-7EN

11.5

86.5

285

10

3600

215HP

230/460

RGZVESD

530

470

1LA02152NE2B

1685

SA-7EN

12

88.5

160

✔

10

1800

215HP

230/460

RGZVESD

690

605

1LA02154NE2B

1685

SA-7EN

12.5

88.5

160

✔

10

1200

256HP

230/460

RGZVESD

1140

1015

2310

SA-7EN

13

88.5

285

150

900

447HP

460

RGZVESD

2730

1450

20451

SA-7EN

186

93

2280

10

900

284HP

230/460

RGZVESD

1275

1140

3045

SA-7EN

15

89.5

485

200

1800

447HP

460

RGZVESD

2115

1115

17120

SA-7EN

225

94.5

2280

15

3600

254HP

230/460

RGZVESD

760

670

1LA02542NE2B

1943

SA-7EN

17

88.5

245

✔

200

1200

449HP

460

RGZVESD

2450

1300

20650

SA-7EN

226

94.1

2600

15

1800

254HP

230/460

RGZVESD

980

870

1LA02544NE2B

2013

SA-7EN

18.7

90.2

245

✔

200

900

449HP

460

RGZVESD

2800

1380

23010

SA-7EN

241

93.6

2600

15

1200

284HP

230/460

RGZVESD

1170

985

2693

SA-7EN

20

89.5

485

250

1800

449HP

460

RGZVESD

2185

1045

19890

SA-7EN

281

94.5

2600

15

900

286HP

230/460

RGZVESD

1310

1100

3703

SA-7EN

23

89.5

520

250

1200

449HP

460

RGZVESD

2520

1230

22710

SA-7EN

280

94.1

2600

20

3600

256HP

230/460

RGZVESD

765

665

1LA02562NE2B

2125

SA-7EN

23

88.5

285

✔

1LA02564NE2B

2295

SA-7EN

26

90.2

285

✔

3273

SA-7EN

26

90.2

520 565

1800

256HP

230/460

RGZVESD

995

855

1200

286HP

230/460

RGZVESD

1190

965

20

900

324HP

230/460

RGZVESD

1330

1080

4522

SA-7EN

31

89.5

25

3600

284HP

460

RGZVESD

785

645

1LA02842NE4B

2289

SA-7EN

29

90.2

485

✔

25

1800

284HP

460

RGZVESD

1020

830

1LA02844NE4B

2558

SA-7EN

29

91.7

485

✔

25

1200

324HP

460

RGZVESD

1795

1535

3830

SA-7EN

33

91

565

25

900

326HP

460

RGZVESD

2000

1720

5184

SA-7EN

38

88.5

710

3600

286HP

460

RGZVESD

795

635

1LA02862NE4B

2478

SA-7EN

34

90.2

520

✔

1800

286HP

460

RGZVESD

1035

815

1LA02864NE4B

2878

SA-7EN

35

91.7

520

✔

30

1200

326HP

460

RGZVESD

1820

1510

4373

SA-7EN

39

91

710

30

900

364HP

460

RGZVESD

2320

1860

6013

SA-7EN

46.8

89.5

800

2-56

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-57

NEMA PREMIUM Severe Duty

30 30

Notes: 1. Derate thrust capacity by 31% to obtain 3 year L10 bearing life. 2. Non Reverse Ratchet available - contact factory.

NEMA PREMIUM General Purpose

20

HIGH EFFICIENT P-Base Vertical

7.5

HIGH EFFICIENT Definite Purpose

100

7.5

20

✔

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Vertical Solid Shaft - Normal Thrust RGZVESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

Vertical Solid Shaft - Normal Thrust RGZVESD

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC P-Base Motors

Introduction

Severe Duty - TEFC P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Performance Specifications •1 to 250 HP •1.0 service factor, 40ºC ambient •T2D temperature code •Continuous thrust: – Up: 355 to 1,860 lbs. – Down: 380 to 2,800 lbs. •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143HP through 449HP frame

Features for Long Life

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable ball bearings with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 1 year. Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Part Number

Multiplier Symbol SA-7EN

FL Amps 460V 1.5

FL Nom. Eff. (%) 82.5

Weight Stock (lbs.) Model 80

HP 1

RPM 1800

1

1200

145HP

230/460

RGZZVESD

445

415

998

SA-7EN

1.6

82.5

1

900

182HP

230/460

RGZZVESD

495

465

1331

SA-7EN

1.9

77

1.5

3600

143HP

230/460

RGZZVESD

295

275

962

SA-7EN

1.9

82.5

1.5

1800

145HP

230/460

RGZZVESD

385

330

896

SA-7EN

2.2

84

85

1.5

1200

182HP

230/460

RGZZVESD

550

510

1124

SA-7EN

2.3

84

130

1.5

900

184HP

230/460

RGZZVESD

615

570

1459

SA-7EN

2.6

78.5

135

2

3600

145HP

230/460

RGZZVESD

295

275

998

SA-7EN

2.5

84

2

1800

145HP

230/460

RGZZVESD

385

350

974

SA-7EN

2.7

84

2

1200

184HP

230/460

RGZZVESD

550

510

1285

SA-7EN

3

85.5

135

2

900

213HP

230/460

RGZZVESD

615

570

1681

SA-7EN

3.3

81.5

175

3

3600

182HP

230/460

RGZZVESD

365

340

1MJ01822NX2B

1214

SA-7EN

3.6

85.5

130

✔

1MJ01824NX2B

✔

3

1800

182HP

230/460

RGZZVESD

480

430

3

1200

213HP

230/460

RGZZVESD

785

725

3

900

215HP

230/460

RGZZVESD

875

810

5

3600

184HP

230/460

RGZZVESD

375

330

1MJ01842NX2B 1MJ01844NX2B

5

1800

184HP

230/460

RGZZVESD

485

425

5

1200

215HP

230/460

RGZZVESD

790

720

85 130 80

85 85

1140

SA-7EN

3.9

86.5

130

1586

SA-7EN

4

86.5

175

2165

SA-7EN

4.7

82.5

195

1617

SA-7EN

5.8

86.5

135

✔ ✔

1459

SA-7EN

6.5

86.5

135

2196

SA-7EN

6.8

87.5

195 295

5

900

254HP

230/460

RGZZVESD

885

805

2550

SA-7EN

7.5

85.5

7.5

3600

213HP

230/460

RGZZVESD

525

475

1MJ02132NX2B

1923

SA-7EN

8.8

87.5

175

✔

7.5

1800

213HP

230/460

RGZZVESD

685

610

1MJ02134NX2B

1974

SA-7EN

9.5

88.5

175

✔

7.5

1200

254HP

230/460

RGZZVESD

1130

1025

2533

SA-7EN

9.8

88.5

295

7.5

900

256HP

230/460

RGZZVESD

1260

1150

3233

SA-7EN

11.5

86.5

365

10

3600

215HP

230/460

RGZZVESD

530

470

1MJ02152NX2B

2165

SA-7EN

12

88.5

195

✔

10

1800

215HP

230/460

RGZZVESD

690

605

1MJ02154NX2B

2165

SA-7EN

12.5

88.5

195

✔

10

1200

256HP

230/460

RGZZVESD

1140

1015

3172

SA-7EN

13

88.5

365

10

900

284HP

230/460

RGZZVESD

1275

1140

3808

SA-7EN

15

89.5

410

15

3600

254HP

230/460

RGZZVESD

760

670

1MJ02542NX2B

2428

SA-7EN

17

88.5

295

✔

15

1800

254HP

230/460

RGZZVESD

980

870

1MJ02544NX2B

2869

SA-7EN

18.7

90.2

295

✔

15

1200

284HP

230/460

RGZZVESD

1170

985

4022

SA-7EN

20

89.5

410

15

900

286HP

230/460

RGZZVESD

1310

1100

4677

SA-7EN

23

89.5

460

20

3600

256HP

230/460

RGZZVESD

765

665

1MJ02562NX2B

2984

SA-7EN

23

88.5

365

✔

20

1800

256HP

230/460

RGZZVESD

995

855

1MJ02564NX2B

3157

SA-7EN

26

90.2

365

✔

20

1200

286HP

230/460

RGZZVESD

1190

965

4613

SA-7EN

26

90.2

460

20

900

324HP

230/460

RGZZVESD

1330

1080

5781

SA-7EN

31

89.5

589

25

3600

284HP

460

RGZZVESD

785

645

1MJ02842NX4B

3565

SA-7EN

29

90.2

410

✔

25

1800

284HP

460

RGZZVESD

1020

830

1MJ02844NX4B

3884

SA-7EN

29

91.7

410

✔

25

1200

324HP

460

RGZZVESD

1795

1535

5641

SA-7EN

33

91

589

25

900

326HP

460

RGZZVESD

2000

1720

6393

SA-7EN

38

88.5

738

30

3600

286HP

460

RGZZVESD

795

635

1MJ02862NX4B

3803

SA-7EN

34

90.2

460

✔

30

1800

286HP

460

RGZZVESD

1035

815

1MJ02864NX4B

4211

SA-7EN

35

91.7

460

✔

30

1200

326HP

460

RGZZVESD

1820

1510

6194

SA-7EN

39

91

738

30

900

364HP

460

RGZZVESD

2320

1860

7898

SA-7EN

46.8

89.5

865

2007 Low Voltage AC Motors Selection and Pricing Guide

2-59

NEMA PREMIUM Severe Duty

2-58

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion.

Type RGZZVESD

List Price $ 816

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

Voltage 230/460

Down (lbs) 355

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. Two series-connected normally closed Class B thermostats are supplied as standard.

Frame 143HP

Up (lbs) 380

HIGH EFFICIENT Definite Purpose

Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end sintered condensation drain, drip cover, and lifting lugs are included.

Cont. Thrust 1 Yr. Life Min.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

Siemens P-base vertical solid shaft explosion-proof motors are UL® listed for use in Class I, Group D, Division 1 hazardous areas and are ideal for applications such as centrifugal and turbine pumps.

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Definite Purpose

Vertical Solid Shaft - Normal Thrust Class I, Group D, Division 1 RGZZVESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT P-Base Vertical

Vertical Solid Shaft - Normal Thrust Class I, Group D, Division 1 RGZZVESD

HIGH EFFICIENT General Purpose

Hazardous Duty P-Base Motors

Introduction

Hazardous Duty - P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

P-base vertical solid shaft high efficiency motors are ideal for applications such as centrifugal and turbine pumps.

Cont. Thrust 1 Yr. Life Min. Down (lbs) 1005

List Part Number Price $ 1MJ03242NX4B 5069

Multiplier Symbol SA-7EN

1MJ03244NX4B

FL Amps 460V 45

FL Nom. Eff. (%) 92.4

HP 40

RPM 3600

Frame 324HP

Voltage 460

Type RGZZVESD

Up (lbs) 1205

Weight Stock (lbs.) Model 589 ✔

40

1800

324HP

460

RGZZVESD

1570

1290

5231

SA-7EN

47

92.4

589

40

1200

364HP

460

RGZZVESD

2075

1675

8135

SA-7EN

52

92.4

865

40

900

365HP

460

RGZZVESD

2340

1840

9047

SA-7EN

63

90.2

915

50

3600

326HP

460

RGZZVESD

1215

995

1MJ03262NX4B

5579

SA-7EN

55

92.4

738

✔

50

1800

326HP

460

RGZZVESD

1585

1275

1MJ03264NX4B

5880

SA-7EN

58

92.4

738

✔

50

1200

365HP

460

RGZZVESD

2095

1660

9180

SA-7EN

66

92.4

915

50

900

404HP

460

RGZZVESD

2370

1810

11369

SA-7EN

67

90.2

1290

60

3600

364HP

460

RGZZVESD

1410

1080

1MJ03642NX4B

7211

SA-7EN

68

92.4

865

✔

60

1800

364HP

460

RGZZVESD

1795

1435

1MJ03644NX4B

7426

SA-7EN

71

92.4

865

✔

60

1200

404HP

460

RGZZVESD

2155

1595

10357

SA-7EN

74

93

1290

60

900

405HP

460

RGZZVESD

2410

1770

11369

SA-7EN

78

90.2

1420

75

3600

365HP

460

RGZZVESD

1420

1070

1MJ03652NX4B

8818

SA-7EN

85

93

915

✔

75

1800

365HP

460

RGZZVESD

1815

1415

1MJ03654NX4B

8928

SA-7EN

87

93

915

✔

75

1200

405HP

460

RGZZVESD

2195

1555

11738

SA-7EN

93

93.6

1420

75

900

444HP

460

RGZZVESD

2495

1685

15188

SA-7EN

94

91.7

1740

100

3600

405HP

460

RGZZVESD

1475

1015

1MJ04052NX4B

10787

SA-7EN

108

93

1420

✔

100

1800

405HP

460

RGZZVESD

1915

1315

1MJ04054NX4B

10389

SA-7EN

113

93.6

1420

✔

100

1200

444HP

460

RGZZVESD

2315

1435

15412

SA-7EN

117

93.6

1740

900

445HP

460

RGZZVESD

2565

1615

18018

SA-7EN

123

93

1930

1800

444HP

460

RGZZVESD

1975

1255

13337

SA-7EN

143

94.1

1740

125

1200

445HP

460

RGZZVESD

2385

1365

17983

SA-7EN

144

93.6

1930

125

900

447HP

460

RGZZVESD

2670

1510

20992

SA-7EN

152

92.4

2450

150

1800

445HP

460

RGZZVESD

2060

1170

15606

SA-7EN

170

94.5

1930 2450

1200

447HP

460

RGZZVESD

2400

1350

22068

SA-7EN

170

94.1

900

447HP

460

RGZZVESD

2730

1450

22899

SA-7EN

186

93

2450

200

1800

447HP

460

RGZZVESD

2115

1115

21043

SA-7EN

225

94.5

2450

200

1200

449HP

460

RGZZVESD

2450

1300

24041

SA-7EN

226

94.1

2650

200

900

449HP

460

RGZZVESD

2800

1380

25719

SA-7EN

241

93.6

2650

250

1800

449HP

460

RGZZVESD

2185

1045

23271

SA-7EN

281

94.5

2650

250

1200

449HP

460

RGZZVESD

2520

1230

26148

SA-7EN

280

94.1

2650

Features for Long Life Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end T-drain, drip cover and lifting lugs are included. Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. This insulation system meets or exceeds NEMA MG1-2003, Part 31 making all motors suitable for operation with variable frequency drives. Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, 143HP – 256HP frames feature drive end open ball bearings and opposite drive end angular contact thrust bearings; 284HP – 365HP frames feature drive end double shielded ball bearings and opposite drive end angular contact thrust bearing plus a four-point contact thrust bearing; 404HP – 449HP frames feature drive end angular contact thrust bearings and opposite drive end double shielded ball bearings with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 1 year.

Lubrication – A specially formulated, high temperature tested, polyureabased grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprenegasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens vertical motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

150 150

•1 to 250 HP •1.15 service factor, 40ºC ambient •Continuous down thrust: 735 to 5160 lbs •Guide bearing locked for 30% momentary upthrust •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143HP through 449HP frame

Notes: 1. Derate thrust capacity by 31% to obtain 3 year L10 bearing life. 2. Non Reverse Ratchet available - contact factory.

2007 Low Voltage AC Motors Selection and Pricing Guide

2-61

NEMA PREMIUM Severe Duty

NEMA PREMIUM General Purpose

2007 Low Voltage AC Motors Selection and Pricing Guide

NEMA PREMIUM General Purpose

Specifications table begins on the next page

2-60

HIGH EFFICIENT Definite Purpose

100 125

✔

Performance Specifications

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Vertical Solid Shaft - Medium Thrust RGZVMTESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM Severe Duty

Severe Duty - P-Base Motors

HIGH EFFICIENT General Purpose

Vertical Solid Shaft - Normal Thrust Class I, Group D, Division 1 RGZZVESD

Introduction

Hazardous Duty P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Cont. Thrust 1 Yr. Life Min. Down (lbs) 915

Custom Build

Cont. Thrust 1 Yr. Life Min. Multiplier Symbol SA-7EN

FL Nom. Eff. (%) 82.5

Weight (lbs.) 70

HP 1

RPM 1800

Frame 143HP

1

1200

145HP

230/460 RGZVMTESD

**

1060

746

SA-7EN

1.6

82.5

1

900

182HP

230/460 RGZVMTESD

**

1150

1141

SA-7EN

1.9

77

1.5

3600

143HP

230/460 RGZVMTESD

**

735

707

SA-7EN

1.9

1.5

1800

145HP

230/460 RGZVMTESD

**

915

636

SA-7EN

1.5

1200

182HP

230/460 RGZVMTESD

**

1390

882

SA-7EN

1.5

900

184HP

230/460 RGZVMTESD

**

1510

1287

SA-7EN

2.6

78.5

2

3600

145HP

230/460 RGZVMTESD

**

735

746

SA-7EN

2.5

84

2

1800

145HP

230/460 RGZVMTESD

**

915

721

SA-7EN

2.7

84

2

1200

184HP

230/460 RGZVMTESD

**

1390

1015

SA-7EN

3

85.5

2

900

213HP

230/460 RGZVMTESD

**

2050

1474

SA-7EN

3.3

81.5

3

3600

182HP

230/460 RGZVMTESD

**

965

979

SA-7EN

3.6

3

1800

182HP

230/460 RGZVMTESD

**

1210

864

SA-7EN

3.9

3

1200

213HP

230/460 RGZVMTESD

**

1870

1340

SA-7EN

3

900

215HP

230/460 RGZVMTESD

**

2050

1854

SA-7EN

Part Number

List Price $ 550

FL Amps 460V 1.5

Up Voltage Type (lbs) 230/460 RGZVMTESD **

Stock Model

Down (lbs) 3090

List Price $ 3742

Multiplier Symbol SA-7EN

FL Amps 460V 45

FL Nom. Eff. (%) 92.4

HP 40

RPM 3600

Frame 324HP

Up Voltage Type (lbs) 460 RGZVMTESD **

75

40

1800

324HP

460

RGZVMTESD

**

3875

3771

SA-7EN

47

92.4

565

85

40

1200

364HP

460

RGZVMTESD

**

4985

6298

SA-7EN

52

92.4

800

82.5

70

40

900

365HP

460

RGZVMTESD

**

5480

7902

SA-7EN

63

90.2

875

2.2

84

75

50

3600

326HP

460

RGZVMTESD

**

3090

4695

SA-7EN

55

92.4

710

2.3

84

85

50

1800

326HP

460

RGZVMTESD

**

3875

4472

SA-7EN

58

92.4

710

100

50

1200

365HP

460

RGZVMTESD

**

4985

7425

SA-7EN

66

92.4

875

75

50

900

404HP

460

RGZVMTESD

**

5410

9450

SA-7EN

67

90.2

1290

75

60

3600

364HP

460

RGZVMTESD

**

3435

5975

SA-7EN

68

92.4

800

100

60

1800

364HP

460

RGZVMTESD

**

4345

5928

SA-7EN

71

92.4

135

60

1200

404HP

460

RGZVMTESD

**

4880

8467

SA-7EN

74

93

1290

85.5

85

60

900

405HP

460

RGZVMTESD

**

5410

10716

SA-7EN

78

90.2

1420

86.5

85

75

3600

365HP

460

RGZVMTESD

**

3435

7387

SA-7EN

85

93

4

86.5

135

75

1800

365HP

460

RGZVMTESD

**

4345

7392

SA-7EN

87

93

4.7

82.5

160

75

1200

405HP

460

RGZVMTESD

**

4880

9957

SA-7EN

93

93.6

Part Number

Weight (lbs.) 565

Stock Model

800

875 875 1420

5

3600

184HP

230/460 RGZVMTESD

**

965

1373

SA-7EN

5.8

86.5

100

75

900

444HP

460

RGZVMTESD

**

5160

14055

SA-7EN

94

91.7

1740

5

1800

184HP

230/460 RGZVMTESD

**

1210

1202

SA-7EN

6.5

86.5

100

100

3600

405HP

460

RGZVMTESD

**

3375

9840

SA-7EN

108

93

1420

113

93.6

1420 1740

215HP

230/460 RGZVMTESD

**

1870

1887

SA-7EN

6.8

87.5

160

100

1800

405HP

460

RGZVMTESD

**

4245

9122

SA-7EN

900

254HP

230/460 RGZVMTESD

**

3260

2269

SA-7EN

7.5

85.5

245

100

1200

444HP

460

RGZVMTESD

**

4485

13272

SA-7EN

117

93.6

7.5

3600

213HP

230/460 RGZVMTESD

**

1300

1703

SA-7EN

8.8

87.5

135

100

900

445HP

460

RGZVMTESD

**

5160

17221

SA-7EN

123

93

1930

7.5

1800

213HP

230/460 RGZVMTESD

**

1630

1648

SA-7EN

9.5

88.5

135

125

1800

444HP

460

RGZVMTESD

**

3920

11943

SA-7EN

143

94.1

1740

7.5

1200

254HP

230/460 RGZVMTESD

**

2980

2250

SA-7EN

9.8

88.5

245

125

1200

445HP

460

RGZVMTESD

**

4485

16044

SA-7EN

144

93.6

1930

7.5

900

256HP

230/460 RGZVMTESD

**

3260

2756

SA-7EN

11.5

86.5

285

125

900

447HP

460

RGZVMTESD

**

3090

19784

SA-7EN

152

92.4

2280

10

3600

215HP

230/460 RGZVMTESD

**

1300

1854

SA-7EN

12

88.5

160

150

1800

445HP

460

RGZVMTESD

**

3920

13778

SA-7EN

170

94.5

1930

10

1800

215HP

230/460 RGZVMTESD

**

1630

1854

SA-7EN

12.5

88.5

160

150

1200

447HP

460

RGZVMTESD

**

4400

19938

SA-7EN

170

94.1

2280

10

1200

256HP

230/460 RGZVMTESD

**

2980

2541

SA-7EN

13

88.5

285

150

900

447HP

460

RGZVMTESD

**

3045

22496

SA-7EN

186

93

2280

10

900

284HP

230/460 RGZVMTESD

**

3250

3350

SA-7EN

15

89.5

485

200

1800

447HP

460

RGZVMTESD

**

3820

18832

SA-7EN

225

94.5

2280

15

3600

254HP

230/460 RGZVMTESD

**

2060

2137

SA-7EN

17

88.5

245

200

1200

449HP

460

RGZVMTESD

**

3600

22715

SA-7EN

226

94.1

2600

15

1800

254HP

230/460 RGZVMTESD

**

2580

2214

SA-7EN

18.7

90.2

245

200

900

449HP

460

RGZVMTESD

**

2910

25311

SA-7EN

241

93.6

2600

15

1200

284HP

230/460 RGZVMTESD

**

2930

2962

SA-7EN

20

89.5

485

250

1800

449HP

460

RGZVMTESD

**

3700

21879

SA-7EN

281

94.5

2600

15

900

286HP

230/460 RGZVMTESD

**

3250

4073

SA-7EN

23

89.5

520

250

1200

449HP

460

RGZVMTESD

**

3600

24981

SA-7EN

280

94.1

2600

20

3600

256HP

230/460 RGZVMTESD

**

2060

2338

SA-7EN

23

88.5

285

20

1800

256HP

230/460 RGZVMTESD

**

2580

2525

SA-7EN

26

90.2

285

20

1200

286HP

230/460 RGZVMTESD

**

2930

3600

SA-7EN

26

90.2

520

20

900

324HP

230/460 RGZVMTESD

**

4930

4974

SA-7EN

31

89.5

565

25

3600

284HP

460

RGZVMTESD

**

2025

2518

SA-7EN

29

90.2

485

25

1800

284HP

460

RGZVMTESD

**

2550

2814

SA-7EN

29

91.7

485

25

1200

324HP

460

RGZVMTESD

**

4465

4213

SA-7EN

33

91

565

25

900

326HP

460

RGZVMTESD

**

4930

5702

SA-7EN

38

88.5

710

30

3600

286HP

460

RGZVMTESD

**

2025

2726

SA-7EN

34

90.2

520

30

1800

286HP

460

RGZVMTESD

**

2550

3166

SA-7EN

35

91.7

520

30

1200

326HP

460

RGZVMTESD

**

4465

4810

SA-7EN

39

91

710

30

900

364HP

460

RGZVMTESD

**

5020

6614

SA-7EN

46.8

89.5

800

HIGH EFFICIENT P-Base Vertical

1200

HIGH EFFICIENT Definite Purpose

5 5

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Vertical Solid Shaft - Medium Thrust RGZVMTESD

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

Custom Build

HIGH EFFICIENT Severe Duty

**Guide bearing is locked for 30% momentary upthrust Notes: 1. Derate thrust capacity by 31% to obtain 3 year L10 bearing life.

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Vertical Solid Shaft - Medium Thrust RGZVMTESD

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-63

NEMA PREMIUM Severe Duty

**Guide bearing is locked for 30% momentary upthrust.

2-62

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty - TEFC P-Base Motors

Introduction

Severe Duty - TEFC P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

•1 to 250 HP •1.0 service factor, 40ºC ambient •T2D temperature code •Continuous down thrust: 735 to 5160 lbs •Guide bearing locked for 30% momentary upthrust •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143HP through 449HP frame

Features for Long Life Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end sintered condensation drain, drip cover and lifting lugs are included.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, 143HP – 256HP frames feature drive end open ball bearings and opposite drive end angular contact thrust bearings; 284HP – 365HP frames feature drive end double shielded ball bearings and opposite drive end angular contact thrust bearing plus a four-point contact thrust bearing; 404HP – 449HP frames feature drive end angular contact thrust bearings and opposite drive end double shielded ball bearings with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 1 year.

2007 Low Voltage AC Motors Selection and Pricing Guide

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Part Number

Multiplier Symbol SA-7EN

FL Amps 460V 1.5

FL Nom. Eff. (%) 82.5

Weight (lbs.) 80

1

1200

145HP

230/460 RGZZVMTESD **

1060

1098

SA-7EN

1.6

82.5

1

900

182HP

230/460 RGZZVMTESD **

1150

1465

SA-7EN

1.9

77

1.5

3600

143HP

230/460 RGZZVMTESD **

735

1058

SA-7EN

1.9

82.5

1.5

1800

145HP

230/460 RGZZVMTESD **

915

985

SA-7EN

2.2

84

85

1.5

1200

182HP

230/460 RGZZVMTESD **

1390

1236

SA-7EN

2.3

84

130

1.5

900

184HP

230/460 RGZZVMTESD **

1510

1604

SA-7EN

2.6

78.5

135

2

3600

145HP

230/460 RGZZVMTESD **

735

1098

SA-7EN

2.5

84

2

1800

145HP

230/460 RGZZVMTESD **

915

1072

SA-7EN

2.7

84

2

1200

184HP

230/460 RGZZVMTESD **

1390

1414

SA-7EN

3

85.5

135

Stock Model

85 130 80

85 85

2

900

213HP

230/460 RGZZVMTESD **

2050

1849

SA-7EN

3.3

81.5

175

3

3600

182HP

230/460 RGZZVMTESD **

965

1335

SA-7EN

3.6

85.5

130

3

1800

182HP

230/460 RGZZVMTESD **

1210

1255

SA-7EN

3.9

86.5

130

3

1200

213HP

230/460 RGZZVMTESD **

1870

1745

SA-7EN

4

86.5

175

3

900

215HP

230/460 RGZZVMTESD **

2050

2382

SA-7EN

4.7

82.5

195

5

3600

184HP

230/460 RGZZVMTESD **

965

1779

SA-7EN

5.8

86.5

135

5

1800

184HP

230/460 RGZZVMTESD **

1210

1604

SA-7EN

6.5

86.5

135

5

1200

215HP

230/460 RGZZVMTESD **

1870

2415

SA-7EN

6.8

87.5

195

5

900

254HP

230/460 RGZZVMTESD **

3260

2805

SA-7EN

7.5

85.5

295

7.5

3600

213HP

230/460 RGZZVMTESD **

1300

2115

SA-7EN

8.8

87.5

175

7.5

1800

213HP

230/460 RGZZVMTESD **

1630

2172

SA-7EN

9.5

88.5

175

7.5

1200

254HP

230/460 RGZZVMTESD **

2980

2786

SA-7EN

9.8

88.5

295

7.5

900

256HP

230/460 RGZZVMTESD **

3260

3557

SA-7EN

11.5

86.5

365

10

3600

215HP

230/460 RGZZVMTESD **

1300

2382

SA-7EN

12

88.5

195

10

1800

215HP

230/460 RGZZVMTESD **

1630

2382

SA-7EN

12.5

88.5

195

10

1200

256HP

230/460 RGZZVMTESD **

2980

3489

SA-7EN

13

88.5

365

10

900

284HP

230/460 RGZZVMTESD **

3250

4188

SA-7EN

15

89.5

410

15

3600

254HP

230/460 RGZZVMTESD **

2060

2670

SA-7EN

17

88.5

295

15

1800

254HP

230/460 RGZZVMTESD **

2580

3156

SA-7EN

18.7

90.2

295

15

1200

284HP

230/460 RGZZVMTESD **

2930

4424

SA-7EN

20

89.5

410

15

900

286HP

230/460 RGZZVMTESD **

3250

5145

SA-7EN

23

89.5

460

20

3600

256HP

230/460 RGZZVMTESD **

2060

3282

SA-7EN

23

88.5

365

20

1800

256HP

230/460 RGZZVMTESD **

2580

3473

SA-7EN

26

90.2

365

20

1200

286HP

230/460 RGZZVMTESD **

2930

5075

SA-7EN

26

90.2

460

20

900

324HP

230/460 RGZZVMTESD **

4930

6360

SA-7EN

31

89.5

589

25

3600

284HP

460

RGZZVMTESD **

2025

3922

SA-7EN

29

90.2

410

25

1800

284HP

460

RGZZVMTESD **

2550

4273

SA-7EN

29

91.7

410

25

1200

324HP

460

RGZZVMTESD **

4465

6205

SA-7EN

33

91

589

25

900

326HP

460

RGZZVMTESD **

4930

7033

SA-7EN

38

88.5

738

30

3600

286HP

460

RGZZVMTESD **

2025

4183

SA-7EN

34

90.2

460

30

1800

286HP

460

RGZZVMTESD **

2550

4632

SA-7EN

35

91.7

460

30

1200

326HP

460

RGZZVMTESD **

4465

6814

SA-7EN

39

91

738

30

900

364HP

460

RGZZVMTESD **

5020

8687

SA-7EN

46.8

89.5

865

2007 Low Voltage AC Motors Selection and Pricing Guide

2-65

NEMA PREMIUM Severe Duty

2-64

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

Frame 143HP

List Price $ 898

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

RPM 1800

Down (lbs) 915

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. Two series-connected normally closed Class B thermostats are provided as standard.

HP 1

Up Voltage Type (lbs) 230/460 RGZZVMTESD **

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

Performance Specifications

Cont. Thrust 1 Yr. Life Min.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT P-Base Vertical

P-base medium thrust vertical solid shaft high efficiency explosion-proof motors are UL® listed for use in Class I,Group D, Division 1 hazardous areas and are ideal for applications such as centrifugal and turbine pumps.

Custom Build

HIGH EFFICIENT Multi Speed

NEMA PREMIUM General Purpose

Vertical Solid Shaft - Medium Thrust Class I, Group D, Division 1 RGZZVMTESD

HIGH EFFICIENT Severe Duty

NEMA PREMIUM Severe Duty

Vertical Solid Shaft - Medium Thrust Class I, Group D, Division 1 RGZZVMTESD

HIGH EFFICIENT General Purpose

Hazardous Duty - P-Base Motors

Introduction

Hazardous Duty - P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Part Number

List Price $ 5576

Multiplier Symbol SA-7EN

FL Amps 460V 45

FL Nom. Eff. (%) 92.4

Weight (lbs.) 589

RPM 3600

Frame 324HP

40

1800

324HP

460

RGZZVMTESD

**

3875

5754

SA-7EN

47

92.4

589

40

1200

364HP

460

RGZZVMTESD

**

4985

8948

SA-7EN

52

92.4

865

40

900

365HP

460

RGZZVMTESD

**

5480

9952

SA-7EN

63

90.2

915

50

3600

326HP

460

RGZZVMTESD

**

3090

6137

SA-7EN

55

92.4

738

50

1800

326HP

460

RGZZVMTESD

**

3875

6469

SA-7EN

58

92.4

738

50

1200

365HP

460

RGZZVMTESD

**

4985

10098

SA-7EN

66

92.4

915

50

900

404HP

460

RGZZVMTESD

**

5410

12506

SA-7EN

67

90.2

1290

60

3600

364HP

460

RGZZVMTESD

**

3435

7933

SA-7EN

68

92.4

865

60

1800

364HP

460

RGZZVMTESD

**

4345

8168

SA-7EN

71

92.4

60

1200

404HP

460

RGZZVMTESD

**

4880

11392

SA-7EN

74

93

1290

60

900

405HP

460

RGZZVMTESD

**

5410

12506

SA-7EN

78

90.2

1420

75

3600

365HP

460

RGZZVMTESD

**

3435

9700

SA-7EN

85

93

75

1800

365HP

460

RGZZVMTESD

**

4345

9821

SA-7EN

87

93

75

1200

405HP

460

RGZZVMTESD

**

4880

12912

SA-7EN

93

93.6

865

915 1420

75

900

444HP

460

RGZZVMTESD

**

5160

16707

SA-7EN

94

91.7

1740

3600

405HP

460

RGZZVMTESD

**

3375

11866

SA-7EN

108

93

1420

100

1800

405HP

460

RGZZVMTESD

**

4245

11428

SA-7EN

113

93.6

1420

100

1200

444HP

460

RGZZVMTESD

**

4485

16953

SA-7EN

117

93.6

1740

•3 to 250 HP •1.15 service factor, 40ºC ambient •Continuous thrust: – Up: 785 to 3,735 lbs. – Down: 735 to 1,550 lbs. – Radial: 930 to 2,140 lbs. •3600, 1800, or 1200 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •182LP through 449LP frame

445HP

460

RGZZVMTESD

**

5160

19821

SA-7EN

123

93

1930

1800

444HP

460

RGZZVMTESD

**

3920

14671

SA-7EN

143

94.1

1740

125

1200

445HP

460

RGZZVMTESD

**

4485

19781

SA-7EN

144

93.6

1930

125

900

447HP

460

RGZZVMTESD

**

23091

SA-7EN

152

92.4

2450

150

1800

445HP

460

RGZZVMTESD

**

3920

17167

SA-7EN

170

94.5

1930

150

1200

447HP

460

RGZZVMTESD

**

4400

24275

SA-7EN

170

94.1

2450

150

900

447HP

460

RGZZVMTESD

**

25189

SA-7EN

186

93

2450

200

1800

447HP

460

RGZZVMTESD

**

23147

SA-7EN

225

94.5

2450

200

1200

449HP

460

RGZZVMTESD

**

26446

SA-7EN

226

94.1

2650

200

900

449HP

460

RGZZVMTESD

**

28292

SA-7EN

241

93.6

2650

250

1800

449HP

460

RGZZVMTESD

**

25599

SA-7EN

281

94.5

2650

250

1200

449HP

460

RGZZVMTESD

**

28763

SA-7EN

280

94.1

2650

Frame & End Shields – Vertical inline solid shaft severe duty motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end T-drain, drip cover and lifting lugs are included. Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable drive end is open ball bearing (182LP – 256LP frames), double shielded ball bearing (284LP – 449LP frames); opposite drive end is a duplex angular contact thrust bearing (143LP – 449LP frames) with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 2 years.

Lubrication – A specially formulated, high temperature tested, polyureabased grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprenegasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens vertical motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

900

125

Features for Long Life

Insulation – Proprietary inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-66

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-67

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Definite Purpose

100

** Guide bearing is locked for 30% momentary upthrust Notes: 1. Derate thrust capacity by 31% to obtain 3 year L10 bearing life.

Performance Specifications

915

100

3820

Stock Model

HIGH EFFICIENT Hazardous Duty

HP 40

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

These motors are ideal for increasing energy savings in applications such as centrifugal and turbine pumps.

Cont. Thrust 1 Yr. Life Min. Down (lbs) 3090

Vertical Solid Shaft - In-Line Thrust RGZVILESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

Custom Build

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Severe Duty - TEFC P-Base Motors

Vertical Solid Shaft - Medium Thrust Class I, Group D, Division 1 RGZZVMTESD Up Voltage Type (lbs) 460 RGZZVMTESD **

Introduction

Hazardous Duty P-Base Motors

Introduction HIGH EFFICIENT General Purpose

Cont. Thrust 2 Yr. Life Min.

HP 3

RPM 3600

Frame 182LP

Up Down Rad. Part List Multiplier Voltage Type (lbs) (lbs) (lbs) Number Price $ Symbol 230/460 RGZVILESD 785 735 930 1LA01822LE2D 1182 SA-7EN

3

1800

182LP

230/460 RGZVILESD

980

910 1160 1LA01824LE2D

Stock/Modifiable

1150

SA-7EN

FL Amps 460V 3.6 3.9

FL Nom. Eff. (%) 85.5 86.5

Weight (lbs.) 133 133

Stock Model ✔ ✔

FL Amps 460V 55

FL Nom. Eff. (%) 92.4

HP 50

RPM 3600

Frame 326LP

Voltage 460

Up Down Rad. Part List Multiplier Type (lbs) (lbs) (lbs) Number Price $ Symbol RGZVILESD 1505 1275 1600 1LA03262LE4D 4706 SA-7EN

Weight (lbs.) 600

50

1800

326LP

460

RGZVILESD 1785 1475 1650 1LA03264LE4D

4359

SA-7EN

58

92.4

600

50

1200

365LP

460

RGZVILESD 2560 2120 2120

6675

SA-7EN

66

92.4

875

Stock Model ✔ ✔

3

1200

213LP

230/460 RGZVILESD 1115 1055 1320

1374

SA-7EN

4

86.5

215

5

3600

184LP

230/460 RGZVILESD

785

735 930 1LA01842LE2D

1306

SA-7EN

5.8

86.5

144

✔

60

3600

364LP

460

RGZVILESD 1840 1510 1475 1LA03642LE4D

5857

SA-7EN

68

92.4

800

✔

5

1800

184LP

230/460 RGZVILESD

980

910 1160 1LA01844LE2D

1233

SA-7EN

6.5

86.5

144

✔

60

1800

364LP

460

RGZVILESD 2330 2060 1850 1LA03644LE4D

5814

SA-7EN

71

92.4

800

✔

5

1200

215LP

230/460 RGZVILESD 1120 1050 1320

1788

SA-7EN

6.8

87.5

160

60

1200

404LP

460

RGZVILESD 2620 2060 2120

7610

SA-7EN

74

93

1290

75

3600

365LP

460

RGZVILESD 1850 1500 1475 1LA03652LE4D

7140

SA-7EN

85

93

875

✔

875

✔

7.5

3600

213LP

230/460 RGZVILESD

785

735 930 1LA02132LE2D

1613

SA-7EN

8.8

87.5

215

✔

980

910 1160 1LA02134LE2D

✔

1800

213LP

230/460 RGZVILESD

1560

SA-7EN

9.5

88.5

215

1200

254LP

230/460 RGZVILESD 1350 1240 1600

2130

SA-7EN

9.8

88.5

245

10

3600

215LP

230/460 RGZVILESD

1755

SA-7EN

88.5

160

10

1800

215LP

230/460 RGZVILESD

10

1200

256LP

15

3600

254LP

1800 1200

254LP

790 985

730 930 1LA02152LE2D

1755

SA-7EN

12.5

88.5

160

230/460 RGZVILESD 1360 1230 1600

2405

SA-7EN

13

88.5

330

230/460 RGZVILESD

2023

SA-7EN

17

88.5

245

945

905 1160 1LA02154LE2D

12

855 1100 1LA02542LE2D

230/460 RGZVILESD 1185 1075 1400 1LA02544LE2D

284LPH 230/460 RGZVILESD 1975 1785 2120

2098 2896

SA-7EN SA-7EN

18.7 20

90.2 89.5

75

1800

365LP

460

RGZVILESD 2345 1945 1850 1LA03654LE4D

7145

SA-7EN

87

93

75

1200

405LP

460

RGZVILESD 2660 2020 2120

8951

SA-7EN

93

93.6

✔

100

3600

405LP

460

RGZVILESD 1905 1445 1475 1LA04052LE4D

9633

SA-7EN

108

93

1300

✔

✔

100

1800

405LP

460

RGZVILESD 2445 1845 1850 1LA04054LE4D

8682

SA-7EN

113

93.6

1300

✔

1300

1200

444LP

460

RGZVILESD 2780 1900 2120

11876

SA-7EN

117

93.6

1740

125

1800

444LP

460

RGZVILESD 2530 1760 1850

11031

SA-7EN

143

94.1

1740

✔

125

1200

445LP

460

RGZVILESD 2850 1830 2120

15335

SA-7EN

144

93.6

1930

375

150

1800

445LP

460

RGZVILESD 2590 1700 1850

12880

SA-7EN

170

94.5

1930

1200

447LP

460

RGZVILESD 2945 1735 2120

17835

SA-7EN

170

94.1

2280

245

20

3600

256LP

230/460 RGZVILESD

850 1100 1LA02562LE2D

2270

SA-7EN

23

88.5

285

✔

150

20

1800

256LP

230/460 RGZVILESD 1200 1060 1400 1LA02564LE2D

2390

SA-7EN

26

90.2

285

✔

200

1800

447LP

460

RGZVILESD 2650 1645 1850

16848

SA-7EN

225

94.5

2280

520

200

1200

449LP

460

RGZVILESD 3040 1640 2120

17866

SA-7EN

226

94.1

2600

375

✔

250

1800

449LP

460

RGZVILESD 2710 1590 1850

18458

SA-7EN

281

94.5

2600

✔

250

1200

449LP

460

RGZVILESD 3735 1550 2120

19328

SA-7EN

280

94.1

2600

20 25

1200 3600

950

286LPH 230/460 RGZVILESD 1990 1770 2120 284LPH 460

1800

284LPH 460

25

1200

324LP

30

3600

286LPH 460

30

1800

286LPH 460

30

1200

326LP

40

3600

324LP

SA-7EN

26 29

90.2 90.2

2665

SA-7EN

29

91.7

RGZVILESD 2010 1750 1875

3988

SA-7EN

33

91

565

RGZVILESD 1470 1310 1475 1LA02862LE4Q

2880

SA-7EN

34

90.2

430

✔

RGZVILESD 1740 1520 1850 1LA02864LE4Q

2998

SA-7EN

35

91.7

430

✔

460

RGZVILESD 2035 1725 1875

4458

SA-7EN

39

91

600

460

RGZVILESD 1490 1290 1600 1LA03242LE4D

3840

SA-7EN

45

92.4

565

✔ ✔

460

RGZVILESD 1725 1535 1850 1LA02844LE4Q

2714

SA-7EN

375

1800

324LP

460

RGZVILESD 1770 1490 1650 1LA03244LE4D

3715

SA-7EN

47

92.4

565

1200

364LP

460

RGZVILESD 2540 2140 2120

5673

SA-7EN

52

92.4

800 HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

40 40

HIGH EFFICIENT Definite Purpose

25

RGZVILESD 1460 1320 1475 1LA02842LE4Q

3410

HIGH EFFICIENT Hazardous Duty

100 ✔

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-68

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-69

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Multi Speed

7.5 7.5

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

Vertical Solid Shaft - In-Line Thrust RGZVILESD

Cont. Thrust 2 Yr. Life Min.

15 HIGH EFFICIENT Hazardous Duty

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Multi Speed

Vertical Solid Shaft - In-Line Thrust RGZVILESD

15

HIGH EFFICIENT Definite Purpose

Severe Duty - TEFC P-Base Motors

Introduction

Severe Duty - TEFC P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

•3 to 250 HP •1.0 service factor, 40ºC ambient •T2D temperature code •Continuous thrust: – Up: 785 to 3,735 lbs. – Down: 735 to 1,550 lbs. – Radial: 930 to 2,140 lbs. •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •182LP through 449LP frame

Features for Long Life Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. A drive end sintered condensation drain, drip cover and lifting lugs are included.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, drive end is open ball bearing (182LP – 256LP frames), double-shielded ball bearing (284LP – 449LP frames); opposite drive end is a duplex angular contact thrust bearing (143LP – 449LP frames) with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 2 years.

2007 Low Voltage AC Motors Selection and Pricing Guide

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

910 1160 1MJ01824LX2D

Weight (lbs.) 130

Stock Model ✔ ✔

3

1800

182LP

230/460 RGZZVILESD 980

1418

SA-7EN

3.9

86.5

135

3

1200

213LP

230/460 RGZZVILESD 1115 1055 1320

1667

SA-7EN

4

86.5

175

5

3600

184LP

230/460 RGZZVILESD 785

735 930 1MJ01842LX2D

1671

SA-7EN

5.8

86.5

135

✔

910 1160 1MJ01844LX2D

✔

5

1800

184LP

230/460 RGZZVILESD 980

1505

SA-7EN

6.5

86.5

135

5

1200

215LP

230/460 RGZZVILESD 1120 1050 1320

2270

SA-7EN

6.8

87.5

195

7.5

3600

213LP

230/460 RGZZVILESD 785

735 930 1MJ02132LX2D

1989

SA-7EN

8.8

87.5

175

✔

7.5

1800

213LP

230/460 RGZZVILESD 980

910 1160 1MJ02134LX2D

✔

7.5

1200

254LP

230/460 RGZZVILESD 1350 1240 1600

10

3600

215LP

230/460 RGZZVILESD 790

10

1800

215LP

230/460 RGZZVILESD 985

10

1200

256LP

15

3600

254LP

15

1800

254LP

15

1200

20 20

2038

SA-7EN

9.5

88.5

175

2619

SA-7EN

9.8

88.5

295

730 930 1MJ02152LX2D

2237

SA-7EN

12

88.5

195

✔

905 1160 1MJ02154LX2D

2237

SA-7EN

12.5

88.5

195

✔

230/460 RGZZVILESD 1360 1230 1600

3269

SA-7EN

13

88.5

365

230/460 RGZZVILESD 945

855 1100 1MJ02542LX2D

2509

SA-7EN

17

88.5

295

✔

230/460 RGZZVILESD 1185 1075 1400 1MJ02544LX2D

2956

SA-7EN

18.7

90.2

295

✔

284LPH 230/460 RGZZVILESD 1975 1785 2120

4136

SA-7EN

20

89.5

410

3600

256LP

230/460 RGZZVILESD 950

850 1100 1MJ02562LX2D

3073

SA-7EN

23

88.5

365

✔

1800

256LP

230/460 RGZZVILESD 1200 1060 1400 1MJ02564LX2D

3254

SA-7EN

26

90.2

365

✔

20

1200

286LPH 230/460 RGZZVILESD 1990 1770 2120

4753

SA-7EN

26

90.2

460

25

3600

284LPH 460

RGZZVILESD 1460 1320 1475 1MJ02842LX4Q

3660

SA-7EN

29

90.2

410

✔

25

1800

284LPH 460

RGZZVILESD 1725 1535 1850 1MJ02844LX4Q

3993

SA-7EN

29

91.7

410

✔

25

1200

324LP

RGZZVILESD 2010 1750 1875

5598

SA-7EN

33

91

589

30

3600

286LPH 460

RGZZVILESD 1470 1310 1475 1MJ02862LX4Q

3907

SA-7EN

34

90.2

460

✔ ✔

460

30

1800

286LPH 460

RGZZVILESD 1740 1520 1850 1MJ02864LX4Q

4333

SA-7EN

35

91.7

460

30

1200

326LP

RGZZVILESD 2035 1725 1875

6143

SA-7EN

39

91

589

460

40

3600

324LP

460

RGZZVILESD 1490 1290 1600 1MJ03242LX4D

5440

SA-7EN

45

92.4

589

✔

40

1800

324LP

460

RGZZVILESD 1770 1490 1650 1MJ03244LX4D

5190

SA-7EN

47

92.4

589

✔

40

1200

364LP

460

RGZZVILESD 2540 2140 2120

8068

SA-7EN

52

92.4

865

50

3600

326LP

460

RGZZVILESD 1505 1275 1600 1MJ03262LX4D

6008

SA-7EN

55

92.4

589

✔

50

1800

326LP

460

RGZZVILESD 1785 1475 1650 1MJ03264LX4D

5834

SA-7EN

58

92.4

589

✔

50

1200

365LP

460

RGZZVILESD 2560 2120 2120

9104

SA-7EN

66

92.4

915

60

3600

364LP

460

RGZZVILESD 1840 1510 1475 1MJ03642LX4D

7757

SA-7EN

68

92.4

865

✔

60

1800

364LP

460

RGZZVILESD 2330 2060 1850 1MJ03644LX4D

7370

SA-7EN

71

92.4

865

✔

60

1200

404LP

460

RGZZVILESD 2620 2060 2120

10268

SA-7EN

74

93

1290

2007 Low Voltage AC Motors Selection and Pricing Guide

2-71

NEMA PREMIUM Severe Duty

2-70

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

Frame 182LP

FL Nom. Eff. (%) 85.5

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

RPM 3600

FL Amps 460V 3.6

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. Two series-connected normally closed Class B thermostats are supplied as standard.

HP 3

Up Down Rad. Part List Multiplier Voltage Type (lbs) (lbs) (lbs) Number Price $ Symbol 230/460 RGZZVILESD 785 735 930 1MJ01822LX2D 1450 SA-7EN

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

Performance Specifications

Cont. Thrust 2 Yr. Life Min.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT P-Base Vertical

P-base in-line vertical solid shaft high efficiency explosion-proof motors are UL® listed for use in Class I, Group D, Division 1 hazardous areas and are ideal for applications such as centrifugal and turbine pumps.

Stock/Modifiable

HIGH EFFICIENT Multi Speed

NEMA PREMIUM General Purpose

Vertical Solid Shaft - In-Line Thrust Class I, Group D, Division 1 RGZZVILESD

HIGH EFFICIENT Severe Duty

NEMA PREMIUM Severe Duty

Vertical Solid Shaft - In-Line Thrust Class I, Group D, Division 1 RGZZVILESD

HIGH EFFICIENT General Purpose

Hazardous Duty - P-Base Motors

Introduction

Hazardous Duty - P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty

Stock/Modifiable

Cont. Thrust 2 Yr. Life Min. Up Down Rad. Voltage Type (lbs) (lbs) (lbs) 460 RGZZVILESD 1850 1500 1475

HP 75

RPM 3600

Frame 365LP

75

1800

365LP

460

RGZZVILESD 2345 1945 1850

Part List Multiplier Number Price $ Symbol 1MJ03652LX4D 9450 SA-7EN 1MJ03654LX4D

8857

SA-7EN

FL Amps 460V 85 87

FL Nom. Weight Stock Eff. (%) (lbs.) Model 93 915 ✔ 93

915

✔

405LP

460

RGZZVILESD 2660 2020 2120

11636

SA-7EN

93

93.6

1335

405LP

460

RGZZVILESD 1905 1445 1475

1MJ04052LX4D

11703

SA-7EN

108

93

1335

✔

100

1800

405LP

460

RGZZVILESD 2445 1845 1850

1MJ04054LX4D

10300

SA-7EN

113

93.6

1335

✔

100

1200

444LP

460

RGZZVILESD 2780 1900 2120

15216

SA-7EN

117

93.6

1740

125

1800

444LP

460

RGZZVILESD 2530 1760 1850

13170

SA-7EN

143

94.1

1740

125

1200

445LP

460

RGZZVILESD 2850 1830 2120

18957

SA-7EN

144

93.6

1930

150

1800

445LP

460

RGZZVILESD 2590 1700 1850

15400

SA-7EN

170

94.5

1930

150

1200

447LP

460

RGZZVILESD 2945 1735 2120

21772

SA-7EN

170

94.1

2450

200

1800

447LP

460

RGZZVILESD 2650 1645 1850

20765

SA-7EN

225

94.5

2450

200

1200

449LP

460

RGZZVILESD 3040 1640 2120

21315

SA-7EN

226

94.1

2650

250

1800

449LP

460

RGZZVILESD 2710 1590 1850

21661

SA-7EN

281

94.5

2650

250

1200

449LP

460

RGZZVILESD 3735 1550 2120

22402

SA-7EN

280

94.1

2650

Performance Specifications •25 to 250 HP •1.15 service factor, 40ºC ambient •Continuous down thrust: 2,600 to 8,000 lbs •30% momentary upthrust •3600, 1800 or 1200 RPM •3 phase, 60 Hz; 230/460 volt operation under 100 HP, 460 volt 100 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •Suitable for part winding start on 100 HP and above •284TP through 449TP frame

Features for Long Life

Cooling – A rugged , metal fan provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable drive end is open ball bearing; opposite drive end is single angular contact thrust bearing (284TP – 449TP frames) with cast iron caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Thrust limits are based on an L10 life of 1 year.

Lubrication – A specially formulated, high temperature tested, grease is used. Specific grease instructions are included on each nameplate. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprenegasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life.

Insulation – Proprietary inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-72

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

2-73

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT Definite Purpose

Frame & End Shields – These motors feature a cast iron frame and end shields for exceptional structural integrity. Each one includes a drive end T-drain, drip cover, lifting lugs, and nonreverse ratchet.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

1200 3600

These motors provide high thrust capacity and are ideal for applications such as irrigation, agriculture, waste water treatment, and turbine pumps.

HIGH EFFICIENT Multi Speed

75 100

Vertical Hollow Shaft - High Thrust HSRGZVESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Multi Speed

Severe Duty - TEFC P-Base Motors

HIGH EFFICIENT General Purpose

Vertical Solid Shaft - In-Line Thrust Class I, Group D, Division 1 RGZZVILESD

Introduction

Hazardous Duty - P-Base Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty

Voltage

Type

25

3600

284TP

230/460

HSRGZVESD

2600

25

1800

284TP

230/460

HSRGZVESD

2600

Part Number 1PM02844PF2V

Multiplier Symbol

FL Amps 460V

2271

SA-7EH

29

91

449

2538

SA-7EH

29

92.4

449 710

List Price

FL Nom. Weight Eff. (%) (lbs.)

Stock Model ✔

GP100A (Cast Aluminum Frame) The new GP100A series of general purpose TEFC motors exceeds NEMA Premium® efficiency standards to signifigantly reduce operating costs and pay for themselves in a short time through energy savings. These industy workhorses are ideal for use in material handling, pump, fan, compressor and other industrial applications.

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses. Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

25

1200

324TP

230/460

HSRGZVESD

3400

3800

SA-7EH

33

91.7

30

3600

286TP

230/460

HSRGZVESD

2900

2457

SA-7EH

34

91

488

30

1800

286TP

230/460

HSRGZVESD

2900

2854

SA-7EH

35

92.4

488

30

1200

326TP

230/460

HSRGZVESD

3400

4337

SA-7EH

39

91.7

660

Performance Specifications

40

3600

324TP

230/460

HSRGZVESD

3400

3543

SA-7EH

46

91.7

710

✔

• 1 to 20 HP • 1.15 service factor, 40°C ambient • 3600, 1800 or 1200 RPM • 3 phase, 60 Hz; 208-230/460 and 575 volt operation • Exceeds NEMA Premium® efficiency standards • Class F insulation, Class B temperature rise @ 1.0SF • NEMA Design B, Continuous Duty • 143T through 256T frame

✔

Features for Long Life

40

1800

324TP

230/460

HSRGZVESD

3400

40

1200

364TP

230/460

HSRGZVESD

4300

3600

326TP

230/460

HSRGZVESD

3400

1800

326TP

230/460

HSRGZVESD

3400

50

1200

365TP

230/460

HSRGZVESD

60

3600

364TP

230/460

HSRGZVESD

1PM03244PF2V

3570

SA-7EH

47

93

710

5962

SA-7EH

52

93

916 660

4441

SA-7EH

55

92.4

4230

SA-7EH

58

93

660

4800

7024

SA-7EH

66

93

1000

4300

5284

SA-7EH

68

93

916

1PM03264PF2V

60

1800

364TP

230/460

HSRGZVESD

4300

5242

SA-7EH

71

93.6

916

60

1200

404TP

230/460

HSRGZVESD

6300

7487

SA-7EH

74

93.6

1250

75

3600

365TP

230/460

HSRGZVESD

4800

6377

SA-7EH

85

93

1000

1800

365TP

230/460

HSRGZVESD

4800

1200

405TP

230/460

HSRGZVESD

6300

100 1800

405TP

460

HSRGZVESD

6300

100 1200

444TP

460

HSRGZVESD

6900

125 1800

444TP

460

HSRGZVESD

6900

125 1200

445TP

460

HSRGZVESD

8000

150 1800

445TP

460

HSRGZVESD

8000

150 1200

447TP

460

HSRGZVESD

8000

200 1800

447TP

460

HSRGZVESD

8000

200 1200

449TP

460

HSRGZVESD

8000

250 1800

449TP

460

HSRGZVESD

8000

250 1200

449TP

460

HSRGZVESD

8000

1PM03654PF2V 1PM04054PFCV 1PM04444PFCV 1PM04454PFCV 1PM04474PFCV 1PM04494PFCV

SA-7EH

87

94.1

1000

SA-7EH

93

93.6

1384

8600

SA-7EH

114

94.5

1384

12512

SA-7EH

117

94.1

1826

11190

SA-7EH

145

94.5

1826

15032

SA-7EH

145

94.1

1870

13665

SA-7EH

170

95

1870

19775

SA-7EH

170

95

2475

19102

SA-7EH

225

95

2475

23041

SA-7EH

226

95

2750

19819

SA-7EH

281

95

2750

22629

SA-7EH

280

95

2750

✔

✔

✔ ✔ ✔

Frame & End Shields - Die cast aluminum construction for exceptional heat dissipation and structural integrity, equipped with bolt-on feet and condensation drain holes. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Polycarbonate fan covers are provided on all frame sizes.

Oversized Conduit Box - Cast aluminum construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - Die cast aluminum construction, structural foam fan and fan cover, zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist corrosion.

Bearings - Lubricated for life, oversized, complete with external bearing protection.

Modifiable - Siemens GP100A motors are available with a variety of modifications and kits.

✔

Rotor - Siemens exclusive, leading edge, die cast copper rotor design provides industry leading efficiencies. Each die cast copper rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

HIGH EFFICIENT P-Base Vertical

HIGH EFFICIENT P-Base Vertical

Notes: 1. Thrust (lbs down) - 1 year L10 Life with 30% momentary up thrust.

6382 8571

✔

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

2-74

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

3-1

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT Definite Purpose

75 75

1PM03644PF2V

✔

HIGH EFFICIENT Hazardous Duty

50 50

1PM02864PF2V

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

RPM Frame

Stock/Modifiable

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Hazardous Duty

HP

Cont. Thrust Down (lbs)

General Purpose - TEFC Motors

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Definite Purpose

Vertical Hollow Shaft - High Thrust HSRGZVESD

Introduction

Severe Duty - TEFC P-Base Motors

HP RPM Frame Voltage Horizontal, Foot Mounted 1 1

Introduction HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty HIGH EFFICIENT Definite Purpose

143T

208-230/460

1

1800

575

1

1200

145T

208-230/460

1

1200

145T

575

1.5

3600

143T

208-230/460

1.5

3600

143T

575

1.5

1800

145T

208-230/460

1.5

1800

145T

575

1.5

1200

182T

208-230/460

1.5

1200

182T

575

2

3600

145T

208-230/460

2

3600

145T

575

2

1800

145T

208-230/460

2

1800

145T

575

2

1200

184T

208-230/460

2

1200

184T

575

3

3600

182T

208-230/460

3

3600

182T

575

3

1800

182T

208-230/460

3

1800

182T

575

3

1200

213T

208-230/460

3

1200

213T

575

Ball

GP100A GP100A

Ball Ball

FL Nom. Eff. (%)

1LE21111AA114AA3

345

GPA2

2.6

87.5

1LE21111AA113AA3 1LE21111AB214AA3

345 345

GPA2 GPA2

2.08 1.5

87.5 86.5

Weight (lbs.) 34 34 47

Stock Model

Voltage

Type

Horizontal, Foot Mounted - continued 20 3600 256T 208-230/460 GP100A

Part Number

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Ball

1LE21112BA214AA3

1564

GPA2

23

92.4

241

✔

✔

256T

575

GP100A

Ball

1LE21112BA213AA3

1564

GPA2

18

92.4

241

✔

✔

20

1800

256T

208-230/460

GP100A

Ball

1LE21112BB214AA3

1485

GPA2

25

93.6

248

✔

20

1800

256T

575

GP100A

Ball

1LE21112BB213AA3

1485

GPA2

20

93.6

248

✔

GP100A

Ball

1LE21111AA114EA3

406

GPA2

2.6

87.5

34

✔

GP100A

Ball

1LE21111AA113EA3

406

GPA2

2.08

87.5

34

1LE21111AB213AA3

345

GPA2

1.2

86.5

47

✔

GP100A

Ball

1LE21111AC314AA3

430

GPA2

1.6

84

48

✔

GP100A

Ball

1LE21111AC313AA3

430

GPA2

1.28

84

48

✔

GP100A

Ball

1LE21111AA214AA3

354

GPA2

1.9

87.5

45

✔

GP100A

Ball

1LE21111AA213AA3

354

GPA2

1.52

87.5

45

✔

GP100A

Ball

1LE21111AB314AA3

380

GPA2

2.1

87.5

48

✔

GP100A

Ball

1LE21111AB313AA3

380

GPA2

1.68

87.5

48

✔

GP100A

Ball

1LE21111CC114AA3

459

GPA2

2.4

87.5

67

✔

GP100A

Ball

1LE21111CC113AA3

459

GPA2

1.92

87.5

67

✔

GP100A

Ball

1LE21111AA314AA3

412

GPA2

2.6

88.5

45

✔

GP100A

Ball

1LE21111AA313AA3

412

GPA2

2.08

88.5

45

✔

GP100A

Ball

1LE21111AB414AA3

413

GPA2

2.8

87.5

48

✔

GP100A

Ball

1LE21111AB413AA3

413

GPA2

2.24

87.5

48

✔

GP100A

Ball

1LE21111CC314AA3

507

GPA2

3

88.5

77

✔

GP100A

Ball

1LE21111CC313AA3

507

GPA2

2.4

88.5

77

✔

GP100A

Ball

1LE21111CA114AA3

459

GPA2

3.8

89.5

71

✔

GP100A

Ball

1LE21111CA113AA3

459

GPA2

3.04

89.5

71

✔

GP100A

Ball

1LE21111CB114AA3

475

GPA2

4

90.2

75

✔

GP100A

Ball

1LE21111CB113AA3

475

GPA2

3.2

90.2

75

✔

GP100A

Ball

1LE21112AC114AA3

652

GPA2

4.3

90.2

110

✔

GP100A

Ball

1LE21112AC113AA3

652

GPA2

3.44

90.2

110

✔

3600

184T

208-230/460

GP100A

Ball

1LE21111CA314AA3

598

GPA2

6.2

90.2

73

✔

3600

184T

575

GP100A

Ball

1LE21111CA313AA3

598

GPA2

4.96

90.2

73

✔

5

1800

184T

208-230/460

GP100A

Ball

1LE21111CB314AA3

541

GPA2

6.7

90.2

79

✔

5

1800

184T

575

GP100A

Ball

1LE21111CB313AA3

541

GPA2

5.36

90.2

79

✔

5

1200

215T

208-230/460

GP100A

Ball

1LE21112AC214AA3

972

GPA2

6.8

90.2

123

✔

5

1200

215T

575

GP100A

Ball

1LE21112AC213AA3

972

GPA2

5.44

90.2

123

✔

7.5

3600

213T

208-230/460

GP100A

Ball

1LE21112AA114AA3

781

GPA2

8.5

91.7

130

✔

7.5

3600

213T

575

GP100A

Ball

1LE21112AA113AA3

781

GPA2

6.8

91.7

130

✔

7.5

1800

213T

208-230/460

GP100A

Ball

1LE21112AB114AA3

757

GPA2

9.5

92.4

137

✔

7.5

1800

213T

575

GP100A

Ball

1LE21112AB113AA3

757

GPA2

7.6

92.4

137

✔

7.5

1200

254T

208-230/460

GP100A

Ball

1LE21112BC114AA3

1304

GPA2

10.5

92.4

244

✔

7.5

1200

254T

575

GP100A

Ball

1LE21112BC113AA3

1304

GPA2

8.4

92.4

244

✔

3600

215T

208-230/460

GP100A

Ball

1LE21112AA214AA3

921

GPA2

11.5

91.7

135

✔

3600

215T

575

GP100A

Ball

1LE21112AA213AA3

921

GPA2

9.2

91.7

135

✔

10

1800

215T

208-230/460

GP100A

Ball

1LE21112AB214AA3

921

GPA2

12.5

92.4

144

✔

10

1800

215T

575

GP100A

Ball

1LE21112AB213AA3

921

GPA2

10

92.4

144

✔

10

1200

256T

208-230/460

GP100A

Ball

1LE21112BC214AA3

1534

GPA2

13.5

92.4

245

✔

10

1200

256T

575

GP100A

Ball

1LE21112BC213AA3

1534

GPA2

10.8

92.4

245

✔

15

3600

254T

208-230/460

GP100A

Ball

1LE21112BA114AA3

1264

GPA2

17

92.4

218

✔

15

3600

254T

575

GP100A

Ball

1LE21112BA113AA3

1264

GPA2

13.6

92.4

218

✔

1800

254T

208-230/460

GP100A

Ball

1LE21112BB114AA3

1234

GPA2

19

93

207

✔

1800

254T

575

GP100A

Ball

1LE21112BB113AA3

1234

GPA2

15.2

93

207

✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3600

143TC

575

1

1800

143TC

208-230/460

GP100A

Ball

1LE21111AB214EA3

406

GPA2

1.5

86.5

47

1

1800

143TC

575

GP100A

Ball

1LE21111AB213EA3

406

GPA2

1.2

86.5

47

1

1200

145TC

208-230/460

GP100A

Ball

1LE21111AC314EA3

491

GPA2

1.6

84

48

1

1200

145TC

575

GP100A

Ball

1LE21111AC313EA3

491

GPA2

1.28

84

48

1.5

3600

143TC

208-230/460

GP100A

Ball

1LE21111AA214EA3

415

GPA2

1.9

87.5

45

1.5

3600

143TC

575

GP100A

Ball

1LE21111AA213EA3

415

GPA2

1.52

87.5

45

1.5

1800

145TC

208-230/460

GP100A

Ball

1LE21111AB314EA3

441

GPA2

2.1

87.5

48

1.5

1800

145TC

575

GP100A

Ball

1LE21111AB313EA3

441

GPA2

1.68

87.5

48

1.5

1200

182TC

208-230/460

GP100A

Ball

1LE21111CC114EA3

546

GPA2

2.4

87.5

67

1.5

1200

182TC

575

GP100A

Ball

1LE21111CC113EA3

546

GPA2

1.92

87.5

67

2

3600

145TC

208-230/460

GP100A

Ball

1LE21111AA314EA3

473

GPA2

2.6

88.5

45

2

3600

145TC

575

GP100A

Ball

1LE21111AA313EA3

473

GPA2

2.08

88.5

45

2

1800

145TC

208-230/460

GP100A

Ball

1LE21111AB414EA3

474

GPA2

2.8

87.5

48

2

1800

145TC

575

GP100A

Ball

1LE21111AB413EA3

474

GPA2

2.24

87.5

48

2

1200

184TC

208-230/460

GP100A

Ball

1LE21111CC314EA3

595

GPA2

3

88.5

77

2

1200

184TC

575

GP100A

Ball

1LE21111CC313EA3

595

GPA2

2.4

88.5

77

3

3600

182TC

208-230/460

GP100A

Ball

1LE21111CA114EA3

546

GPA2

3.8

89.5

71

3

3600

182TC

575

GP100A

Ball

1LE21111CA113EA3

546

GPA2

3.04

89.5

71

3

1800

182TC

208-230/460

GP100A

Ball

1LE21111CB114EA3

562

GPA2

4

90.2

75

3

1800

182TC

575

GP100A

Ball

1LE21111CB113EA3

562

GPA2

3.2

90.2

75

3

1200

213TC

208-230/460

GP100A

Ball

1LE21112AC114EA3

739

GPA2

4.3

90.2

110

3

1200

213TC

575

GP100A

Ball

1LE21112AC113EA3

739

GPA2

3.44

90.2

110

5

3600

184TC

208-230/460

GP100A

Ball

1LE21111CA314EA3

685

GPA2

6.2

90.2

73

5

3600

184TC

575

GP100A

Ball

1LE21111CA313EA3

685

GPA2

4.96

90.2

73

5

1800

184TC

208-230/460

GP100A

Ball

1LE21111CB314EA3

628

GPA2

6.7

90.2

79

5

1800

184TC

575

GP100A

Ball

1LE21111CB313EA3

628

GPA2

5.36

90.2

79

5

1200

215TC

208-230/460

GP100A

Ball

1LE21112AC214EA3

1059

GPA2

6.8

90.2

123

5

1200

215TC

575

GP100A

Ball

1LE21112AC213EA3

1059

GPA2

5.44

90.2

123

7.5

3600

213TC

208-230/460

GP100A

Ball

1LE21112AA114EA3

869

GPA2

8.5

91.7

130

7.5

3600

213TC

575

GP100A

Ball

1LE21112AA113EA3

869

GPA2

6.8

91.7

130

7.5

1800

213TC

208-230/460

GP100A

Ball

1LE21112AB114EA3

845

GPA2

9.5

92.4

137

7.5

1800

213TC

575

GP100A

Ball

1LE21112AB113EA3

845

GPA2

7.6

92.4

137

7.5

1200

254TC

208-230/460

GP100A

Ball

1LE21112BC114EA3

1418

GPA2

10.5

92.4

244

7.5

1200

254TC

575

GP100A

Ball

1LE21112BC113EA3

1418

GPA2

8.4

92.4

244

10

3600

215TC

208-230/460

GP100A

Ball

1LE21112AA214EA3

1009

GPA2

11.5

91.7

135

10

3600

215TC

575

GP100A

Ball

1LE21112AA213EA3

1009

GPA2

9.2

91.7

135

10

1800

215TC

208-230/460

GP100A

Ball

1LE21112AB214EA3

1009

GPA2

12.5

92.4

144

10

1800

215TC

575

GP100A

Ball

1LE21112AB213EA3

1009

GPA2

10

92.4

144

10

1200

256TC

208-230/460

GP100A

Ball

1LE21112BC214EA3

1647

GPA2

13.5

92.4

245

10

1200

256TC

575

GP100A

Ball

1LE21112BC213EA3

1647

GPA2

10.8

92.4

245

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-3

NEMA PREMIUM Severe Duty

15 15

1

NEMA PREMIUM General Purpose

10 10

C-Face, Horizontal, Foot Mounted 1 3600 143TC 208-230/460

HIGH EFFICIENT P-Base Vertical

5

2007 Low Voltage AC Motors Selection and Pricing Guide

Frame

Multiplier Symbol

3600

5

3-2

RPM

List Price $

20

✔

Ball

GP100A

HP

DE Bearing

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT P-Base Vertical

143T

575

GP100A

FL Amps*

HIGH EFFICIENT Hazardous Duty

NEMA PREMIUM General Purpose

1800

143T

208-230/460

Multiplier Symbol

Stock/Modifiable

HIGH EFFICIENT Multi Speed

NEMA PREMIUM Severe Duty

3600

143T

Part Number

List Price $

GP100A (Cast Aluminum Frame)

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

1

3600

Type

DE Bearing

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT General Purpose

GP100A (Cast Aluminum Frame)

Introduction

General Purpose - TEFC Motors

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

15

3600

254TC

208-230/460

GP100A

Ball

1LE21112BA114EA3

1378

GPA2

17

92.4

218

15

3600

254TC

575

GP100A

Ball

1LE21112BA113EA3

1378

GPA2

13.6

92.4

218

15

1800

254TC

208-230/460

GP100A

Ball

1LE21112BB114EA3

1348

GPA2

19

93

207

15

1800

254TC

575

GP100A

Ball

1LE21112BB113EA3

1348

GPA2

15.2

93

207

20

3600

256TC

208-230/460

GP100A

Ball

1LE21112BA214EA3

1678

GPA2

23

92.4

241

20

3600

256TC

575

GP100A

Ball

1LE21112BA213EA3

1678

GPA2

18

92.4

241

20

1800

256TC

208-230/460

GP100A

Ball

1LE21112BB214EA3

1599

GPA2

25

93.6

248

20

1800

256TC

575

GP100A

Ball

1LE21112BB213EA3

1599

GPA2

20

93.6

248

Stock Model ✔ ✔ ✔ ✔

C-Face, Horizontal, Footless 1

3600

143TC

208-230/460

GP100A

Ball

1LE21111AA114GA3

422

GPA2

2.6

1

3600

143TC

575

GP100A

Ball

1

1800

143TC

208-230/460

GP100A

Ball

1

1800

143TC

575

GP100A

1

1200

145TC

208-230/460

1

1200

145TC

1.5

3600

143TC

87.5

34

1LE21111AA113GA3

422

GPA2

2.08

87.5

34

1LE21111AB214GA3

422

GPA2

1.5

86.5

47

Ball

1LE21111AB213GA3

422

GPA2

1.2

86.5

47

GP100A

Ball

1LE21111AC314GA3

507

GPA2

1.6

84

48

575

GP100A

Ball

1LE21111AC313GA3

507

GPA2

1.28

84

48

208-230/460

GP100A

Ball

1LE21111AA214GA3

431

GPA2

1.9

87.5

45

1.5

3600

143TC

575

GP100A

Ball

1LE21111AA213GA3

431

GPA2

1.52

87.5

45

1.5

1800

145TC

208-230/460

GP100A

Ball

1LE21111AB314GA3

457

GPA2

2.1

87.5

48

1.5

1800

145TC

575

GP100A

Ball

1LE21111AB313GA3

457

GPA2

1.68

87.5

48

1.5

1200

182TC

208-230/460

GP100A

Ball

1LE21111CC114GA3

573

GPA2

2.4

87.5

67

575

GP100A

Ball

1LE21111CC113GA3

573

GPA2

1.92

87.5

67

145TC

208-230/460

GP100A

Ball

1LE21111AA314GA3

489

GPA2

2.6

88.5

45

2

3600

145TC

575

GP100A

Ball

1LE21111AA313GA3

489

GPA2

2.08

88.5

45

2

1800

145TC

208-230/460

GP100A

Ball

1LE21111AB414GA3

490

GPA2

2.8

87.5

48

2

1800

145TC

575

GP100A

Ball

1LE21111AB413GA3

490

GPA2

2.24

87.5

48

2

1200

184TC

208-230/460

GP100A

Ball

1LE21111CC314GA3

621

GPA2

3

88.5

77

2

1200

184TC

575

GP100A

Ball

1LE21111CC313GA3

621

GPA2

2.4

88.5

77

3

3600

182TC

208-230/460

GP100A

Ball

1LE21111CA114GA3

573

GPA2

3.8

89.5

71

3

3600

182TC

575

GP100A

Ball

1LE21111CA113GA3

573

GPA2

3.04

89.5

71

3

1800

182TC

208-230/460

GP100A

Ball

1LE21111CB114GA3

588

GPA2

4

90.2

75

3

1800

182TC

575

GP100A

Ball

1LE21111CB113GA3

588

GPA2

3.2

90.2

75

3

1200

213TC

208-230/460

GP100A

Ball

1LE21112AC114GA3

766

GPA2

4.3

90.2

110

3

1200

213TC

575

GP100A

Ball

1LE21112AC113GA3

766

GPA2

3.44

90.2

110

5

3600

184TC

208-230/460

GP100A

Ball

1LE21111CA314GA3

712

GPA2

6.2

90.2

73

5

3600

184TC

575

GP100A

Ball

1LE21111CA313GA3

712

GPA2

4.96

90.2

73

5

1800

184TC

208-230/460

GP100A

Ball

1LE21111CB314GA3

655

GPA2

6.7

90.2

79

5

1800

184TC

575

GP100A

Ball

1LE21111CB313GA3

655

GPA2

5.36

90.2

79

5

1200

215TC

208-230/460

GP100A

Ball

1LE21112AC214GA3

1086

GPA2

6.8

90.2

123

5

1200

215TC

575

GP100A

Ball

1LE21112AC213GA3

1086

GPA2

5.44

90.2

123

7.5

3600

213TC

208-230/460

GP100A

Ball

1LE21112AA114GA3

895

GPA2

8.5

91.7

130

3600

213TC

575

GP100A

Ball

1LE21112AA113GA3

895

GPA2

6.8

91.7

130

1800

213TC

208-230/460

GP100A

Ball

1LE21112AB114GA3

871

GPA2

9.5

92.4

137

7.5

1800

213TC

575

GP100A

Ball

1LE21112AB113GA3

871

GPA2

7.6

92.4

137

7.5

1200

254TC

208-230/460

GP100A

Ball

1LE21112BC114GA3

1458

GPA2

10.5

92.4

244

7.5

1200

254TC

575

GP100A

Ball

1LE21112BC113GA3

1458

GPA2

8.4

92.4

244

FL Nom. Eff. (%)

Weight (lbs.)

10

3600

215TC

208-230/460

GP100A

Ball

1LE21112AA214GA3

1035

GPA2

11.5

91.7

135

10

3600

215TC

575

GP100A

Ball

1LE21112AA213GA3

1035

GPA2

9.2

91.7

135

10

1800

215TC

208-230/460

GP100A

Ball

1LE21112AB214GA3

1035

GPA2

12.5

92.4

144

10

1800

215TC

575

GP100A

Ball

1LE21112AB213GA3

1035

GPA2

10

92.4

144

10

1200

256TC

208-230/460

GP100A

Ball

1LE21112BC214GA3

1688

GPA2

13.5

92.4

245

10

1200

256TC

575

GP100A

Ball

1LE21112BC213GA3

1688

GPA2

10.8

92.4

245

15

3600

254TC

208-230/460

GP100A

Ball

1LE21112BA114GA3

1418

GPA2

17

92.4

218

15

3600

254TC

575

GP100A

Ball

1LE21112BA113GA3

1418

GPA2

13.6

92.4

218

15

1800

254TC

208-230/460

GP100A

Ball

1LE21112BB114GA3

1388

GPA2

19

93

207

15

1800

254TC

575

GP100A

Ball

1LE21112BB113GA3

1388

GPA2

15.2

93

207

20

3600

256TC

208-230/460

GP100A

Ball

1LE21112BA214GA3

1718

GPA2

23

92.4

241

20

3600

256TC

575

GP100A

Ball

1LE21112BA213GA3

1718

GPA2

18

92.4

241

20

1800

256TC

208-230/460

GP100A

Ball

1LE21112BB214GA3

1639

GPA2

25

93.6

248

20

1800

256TC

575

GP100A

Ball

1LE21112BB213GA3

1639

GPA2

20

93.6

248

Stock Model ✔ ✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-4

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-5

NEMA PREMIUM Severe Duty

7.5 7.5

FL Amps*

NEMA PREMIUM General Purpose

182TC

3600

✔

Multiplier Symbol

HIGH EFFICIENT P-Base Vertical

1200

2

✔

Part Number

List Price $

HIGH EFFICIENT Definite Purpose

1.5

✔

HP RPM Frame Voltage Type C-Face, Horizontal, Footless - continued

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Part Number

List Price $

GP100A (Cast Aluminum Frame)

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

HP RPM Frame Voltage Type C-Face, Horizontal, Foot Mounted - continued

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

GP100A (Cast Aluminum Frame)

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose

GP100 (Cast Iron Frame)

The new GP100 series of general purpose TEFC motors exceeds NEMA Premium® efficiency standards to signifigantly reduce operating costs and pay for themselves in a short period of time through energy savings. These industy workhorses are ideal for use in material handling, pump, fan, compressor and other industrial applications.

Performance Specifications • • • •

•

HIGH EFFICIENT Definite Purpose

Frame & End Shields - Cast iron construction for exceptional structural integrity, equipped with integrally cast feet and condensation drain holes. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

1

Oversized Conduit Box - Cast aluminum construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - Cast iron construction, polycarbonate fan, zincplated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable - Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

3600

143T

575

Part Number

Weight (lbs.)

Stock Model

GP100

Ball

1LE22111AA114AA3

375

GP2

2.6

87.5

65

✔

GP100

Ball

1LE22111AA113AA3

375

GP2

2.08

87.5

65

✔

1

1800

143T

208-230/460

GP100

Ball

1LE22111AB214AA3

375

GP2

1.5

86.5

67

✔

1

1800

143T

575

GP100

Ball

1LE22111AB213AA3

375

GP2

1.2

86.5

67

✔

1

1200

145T

208-230/460

GP100

Ball

1LE22111AC314AA3

467

GP2

1.6

84

67

✔

1

1200

145T

575

GP100

Ball

1LE22111AC313AA3

467

GP2

1.28

84

67

✔

1.5 3600

143T

208-230/460

GP100

Ball

1LE22111AA214AA3

385

GP2

1.9

87.5

65

✔

1.5 3600

143T

575

GP100

Ball

1LE22111AA213AA3

385

GP2

1.52

87.5

65

✔

1.5 1800

145T

208-230/460

GP100

Ball

1LE22111AB314AA3

413

GP2

2.1

87.5

67

✔

1.5 1800

145T

575

GP100

Ball

1LE22111AB313AA3

413

GP2

1.68

87.5

67

✔

1.5 1200

182T

208-230/460

GP100

Ball

1LE22111CC114AA3

499

GP2

2.4

87.5

97

✔

1.5 1200

182T

575

GP100

Ball

1LE22111CC113AA3

499

GP2

1.92

87.5

97

✔

2

3600

145T

208-230/460

GP100

Ball

1LE22111AA314AA3

448

GP2

2.6

88.5

66

✔

2

3600

145T

575

GP100

Ball

1LE22111AA313AA3

448

GP2

2.08

88.5

66

✔

2

1800

145T

208-230/460

GP100

Ball

1LE22111AB414AA3

449

GP2

2.8

87.5

68

✔

2

1800

145T

575

GP100

Ball

1LE22111AB413AA3

449

GP2

2.24

87.5

68

✔

2

1200

184T

208-230/460

GP100

Ball

1LE22111CC314AA3

551

GP2

3

88.5

107

✔

2

1200

184T

575

GP100

Ball

1LE22111CC313AA3

551

GP2

2.4

88.5

107

✔

3

3600

182T

208-230/460

GP100

Ball

1LE22111CA114AA3

499

GP2

3.8

89.5

101

✔

3

3600

182T

575

GP100

Ball

1LE22111CA113AA3

499

GP2

3.04

89.5

101

✔

3

1800

182T

208-230/460

GP100

Ball

1LE22111CB114AA3

516

GP2

4

90.2

105

✔

3

1800

182T

575

GP100

Ball

1LE22111CB113AA3

516

GP2

3.2

90.2

105

✔

3

1200

213T

208-230/460

GP100

Ball

1LE22112AC114AA3

709

GP2

4.3

90.2

150

✔

3

1200

213T

575

GP100

Ball

1LE22112AC113AA3

709

GP2

3.44

90.2

150

✔

5

3600

184T

208-230/460

GP100

Ball

1LE22111CA314AA3

650

GP2

6.2

90.2

103

✔

5

3600

184T

575

GP100

Ball

1LE22111CA313AA3

650

GP2

4.96

90.2

103

✔

5

1800

184T

208-230/460

GP100

Ball

1LE22111CB314AA3

588

GP2

6.7

90.2

109

✔

5

1800

184T

575

GP100

Ball

1LE22111CB313AA3

588

GP2

5.36

90.2

109

✔

5

1200

215T

208-230/460

GP100

Ball

1LE22112AC214AA3

1057

GP2

6.8

90.2

163

✔

5

1200

215T

575

GP100

Ball

1LE22112AC213AA3

1057

GP2

5.44

90.2

163

✔

7.5 3600

213T

208-230/460

GP100

Ball

1LE22112AA114AA3

849

GP2

8.5

91.7

178

✔

7.5 3600

213T

575

GP100

Ball

1LE22112AA113AA3

849

GP2

6.8

91.7

178

✔

7.5 1800

213T

208-230/460

GP100

Ball

1LE22112AB114AA3

823

GP2

9.5

92.4

178

✔

7.5 1800

213T

575

GP100

Ball

1LE22112AB113AA3

823

GP2

7.6

92.4

178

✔

7.5 1200

254T

208-230/460

GP100

Ball

1LE22112BC114AA3

1418

GP2

10.5

92.4

307

✔

7.5 1200

254T

575

GP100

Ball

1LE22112BC113AA3

1418

GP2

8.4

92.4

307

✔

10

3600

215T

208-230/460

GP100

Ball

1LE22112AA214AA3

1001

GP2

11.5

91.7

185

✔

10

3600

215T

575

GP100

Ball

1LE22112AA213AA3

1001

GP2

9.2

91.7

185

✔

10

1800

215T

208-230/460

GP100

Ball

1LE22112AB214AA3

1001

GP2

12.5

92.4

185

✔

10

1800

215T

575

GP100

Ball

1LE22112AB213AA3

1001

GP2

10

92.4

185

✔

10

1200

256T

208-230/460

GP100

Ball

1LE22112BC214AA3

1667

GP2

13.5

92.4

307

✔

10

1200

256T

575

GP100

Ball

1LE22112BC213AA3

1667

GP2

10.8

92.4

307

✔

15

3600

254T

208-230/460

GP100

Ball

1LE22112BA114AA3

1374

GP2

17

92.4

279

✔

15

3600

254T

575

GP100

Ball

1LE22112BA113AA3

1374

GP2

13.6

92.4

279

✔

15

1800

254T

208-230/460

GP100

Ball

1LE22112BB114AA3

1341

GP2

19

93

268

✔

15

1800

254T

575

GP100

Ball

1LE22112BB113AA3

1341

GP2

15.2

93

268

✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-6

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-7

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Horizontal, Foot Mounted 1 3600 143T 208-230/460

Type

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Voltage

FL Amps*

HIGH EFFICIENT P-Base Vertical

Rotor - Siemens exclusive, leading edge, die cast copper rotor design provides industry leading efficiencies. Each die cast copper rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Bearings - Lubricated for life, oversized, complete with external bearing protection.

Frame

Multiplier Symbol

HIGH EFFICIENT Definite Purpose

HIGH EFFICIENT P-Base Vertical

Features for Long Life

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Polycarbonate fan covers are provided on all frame sizes.

RPM

List Price $

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

• •

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HP

DE Bearing

HIGH EFFICIENT Multi Speed

•

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800 or 1200 RPM 3 phase, 60 Hz; 208-230/460 and 575 volt operation Exceeds NEMA Premium® efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 143T through 256T frame

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

Stock/Modifiable

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

GP100 (Cast Iron Frame)

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Multi Speed

General Purpose - TEFC Motors

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Voltage

Type

Part Number

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

HP

RPM

Frame

Voltage

Type

DE Bearing

List Price $

Part Number

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Horizontal, Foot Mounted - continued

20

3600

256T

208-230/460

GP100

Ball

1LE22112BA214AA3

1700

GP2

23

92.4

303

✔

15

3600

254TC

208-230/460

GP100

Ball

1LE22112BA114EA3

1478

GP2

17

92.4

279

20

3600

256T

575

GP100

Ball

1LE22112BA213AA3

1700

GP2

18

92.4

303

✔

15

3600

254TC

575

GP100

Ball

1LE22112BA113EA3

1478

GP2

13.6

92.4

279

20

1800

256T

208-230/460

GP100

Ball

1LE22112BB214AA3

1614

GP2

25

93.6

311

✔

15

1800

254TC

208-230/460

GP100

Ball

1LE22112BB114EA3

1445

GP2

19

93

268

20

1800

256T

575

GP100

Ball

1LE22112BB213AA3

1614

GP2

20

93.6

311

✔

15

1800

254TC

575

GP100

Ball

1LE22112BB113EA3

1445

GP2

15.2

93

268

20

3600

256TC

208-230/460

GP100

Ball

1LE22112BA214EA3

1804

GP2

23

92.4

303

431

GP2

2.6

87.5

65

✔

20

3600

256TC

575

GP100

Ball

1LE22112BA213EA3

1804

GP2

18

92.4

303

20

1800

256TC

208-230/460

GP100

Ball

1LE22112BB214EA3

1718

GP2

25

93.6

311

✔

20

1800

256TC

575

GP100

Ball

1LE22112BB213EA3

1718

GP2

20

93.6

311

C-Face, Horizontal, Foot Mounted 143TC

208-230/460

GP100

Ball

1LE22111AA114EA3

1

3600

143TC

575

GP100

Ball

1LE22111AA113EA3

431

GP2

2.08

87.5

65

1

1800

143TC

208-230/460

GP100

Ball

1LE22111AB214EA3

431

GP2

1.5

86.5

67

1

1800

143TC

575

GP100

Ball

1LE22111AB213EA3

431

GP2

1.2

86.5

67

1

1200

145TC

208-230/460

GP100

Ball

1LE22111AC314EA3

523

GP2

1.6

84

67

1

1200

145TC

575

GP100

Ball

1LE22111AC313EA3

523

GP2

1.28

84

67

1.5

3600

143TC

208-230/460

GP100

Ball

1LE22111AA214EA3

440

GP2

1.9

87.5

65

1.5

3600

143TC

575

GP100

Ball

1LE22111AA213EA3

440

GP2

1.52

87.5

65

1.5

1800

145TC

208-230/460

GP100

Ball

1LE22111AB314EA3

469

GP2

2.1

87.5

67

1.5

1800

145TC

575

GP100

Ball

1LE22111AB313EA3

469

GP2

1.68

87.5

67

1.5

1200

182TC

208-230/460

GP100

Ball

1LE22111CC114EA3

579

GP2

2.4

87.5

97

1.5

1200

182TC

575

GP100

Ball

1LE22111CC113EA3

579

GP2

1.92

87.5

97

2

3600

145TC

208-230/460

GP100

Ball

1LE22111AA314EA3

503

GP2

2.6

88.5

66

2

3600

145TC

575

GP100

Ball

1LE22111AA313EA3

503

GP2

2.08

88.5

66

2

1800

145TC

208-230/460

GP100

Ball

1LE22111AB414EA3

505

GP2

2.8

87.5

68

2

1800

145TC

575

GP100

Ball

1LE22111AB413EA3

505

GP2

2.24

87.5

68

2

1200

184TC

208-230/460

GP100

Ball

1LE22111CC314EA3

631

GP2

3

88.5

107

2

1200

184TC

575

GP100

Ball

1LE22111CC313EA3

631

GP2

2.4

88.5

107

3

3600

182TC

208-230/460

GP100

Ball

1LE22111CA114EA3

579

GP2

3.8

89.5

101

3

3600

182TC

575

GP100

Ball

1LE22111CA113EA3

579

GP2

3.04

89.5

101

3

1800

182TC

208-230/460

GP100

Ball

1LE22111CB114EA3

596

GP2

4

90.2

105

3

1800

182TC

575

GP100

Ball

1LE22111CB113EA3

596

GP2

3.2

90.2

105

3

1200

213TC

208-230/460

GP100

Ball

1LE22112AC114EA3

789

GP2

4.3

90.2

150

3

1200

213TC

575

GP100

Ball

1LE22112AC113EA3

789

GP2

3.44

90.2

150

5

3600

184TC

208-230/460

GP100

Ball

1LE22111CA314EA3

729

GP2

6.2

90.2

103

5

3600

184TC

575

GP100

Ball

1LE22111CA313EA3

729

GP2

4.96

90.2

103

5

1800

184TC

208-230/460

GP100

Ball

1LE22111CB314EA3

668

GP2

6.7

90.2

109

5

1800

184TC

575

GP100

Ball

1LE22111CB313EA3

668

GP2

5.36

90.2

109

1200

215TC

208-230/460

GP100

Ball

1LE22112AC214EA3

1136

GP2

6.8

90.2

163

1200

215TC

575

GP100

Ball

1LE22112AC213EA3

1136

GP2

5.44

90.2

163

7.5

3600

213TC

208-230/460

GP100

Ball

1LE22112AA114EA3

929

GP2

8.5

91.7

178

7.5

3600

213TC

575

GP100

Ball

1LE22112AA113EA3

929

GP2

6.8

91.7

178

7.5

1800

213TC

208-230/460

GP100

Ball

1LE22112AB114EA3

903

GP2

9.5

92.4

178

7.5

1800

213TC

575

GP100

Ball

1LE22112AB113EA3

903

GP2

7.6

92.4

178

7.5

1200

254TC

208-230/460

GP100

Ball

1LE22112BC114EA3

1521

GP2

10.5

92.4

307

7.5

1200

254TC

575

GP100

Ball

1LE22112BC113EA3

1521

GP2

8.4

92.4

307

10

3600

215TC

208-230/460

GP100

Ball

1LE22112AA214EA3

1081

GP2

11.5

91.7

185

10

3600

215TC

575

GP100

Ball

1LE22112AA213EA3

1081

GP2

9.2

91.7

185

10

1800

215TC

208-230/460

GP100

Ball

1LE22112AB214EA3

1081

GP2

12.5

92.4

185

10

1800

215TC

575

GP100

Ball

1LE22112AB213EA3

1081

GP2

10

92.4

185

1200

256TC

208-230/460

GP100

Ball

1LE22112BC214EA3

1771

GP2

13.5

92.4

307

10

1200

256TC

575

GP100

Ball

1LE22112BC213EA3

1771

GP2

10.8

92.4

307

C-Face, Horizontal, Footless ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

1

3600

143TC

208-230/460

GP100

Ball

1LE22111AA114GA3

446

GP2

2.6

87.5

65

1

3600

143TC

575

GP100

Ball

1LE22111AA113GA3

446

GP2

2.08

87.5

65

1

1800

143TC

208-230/460

GP100

Ball

1LE22111AB214GA3

446

GP2

1.5

86.5

67

1

1800

143TC

575

GP100

Ball

1LE22111AB213GA3

446

GP2

1.2

86.5

67

1

1200

145TC

208-230/460

GP100

Ball

1LE22111AC314GA3

538

GP2

1.6

84

67

1

1200

145TC

575

GP100

Ball

1LE22111AC313GA3

538

GP2

1.28

84

67

1.5

3600

143TC

208-230/460

GP100

Ball

1LE22111AA214GA3

455

GP2

1.9

87.5

65

1.5

3600

143TC

575

GP100

Ball

1LE22111AA213GA3

455

GP2

1.52

87.5

65

1.5

1800

145TC

208-230/460

GP100

Ball

1LE22111AB314GA3

484

GP2

2.1

87.5

67

1.5

1800

145TC

575

GP100

Ball

1LE22111AB313GA3

484

GP2

1.68

87.5

67

1.5

1200

182TC

208-230/460

GP100

Ball

1LE22111CC114GA3

603

GP2

2.4

87.5

97

1.5

1200

182TC

575

GP100

Ball

1LE22111CC113GA3

603

GP2

1.92

87.5

97

2

3600

145TC

208-230/460

GP100

Ball

1LE22111AA314GA3

518

GP2

2.6

88.5

66

2

3600

145TC

575

GP100

Ball

1LE22111AA313GA3

518

GP2

2.08

88.5

66

2

1800

145TC

208-230/460

GP100

Ball

1LE22111AB414GA3

519

GP2

2.8

87.5

68

2

1800

145TC

575

GP100

Ball

1LE22111AB413GA3

519

GP2

2.24

87.5

68

2

1200

184TC

208-230/460

GP100

Ball

1LE22111CC314GA3

655

GP2

3

88.5

107

2

1200

184TC

575

GP100

Ball

1LE22111CC313GA3

655

GP2

2.4

88.5

107

3

3600

182TC

208-230/460

GP100

Ball

1LE22111CA114GA3

603

GP2

3.8

89.5

101

3

3600

182TC

575

GP100

Ball

1LE22111CA113GA3

603

GP2

3.04

89.5

101

3

1800

182TC

208-230/460

GP100

Ball

1LE22111CB114GA3

620

GP2

4

90.2

105

3

1800

182TC

575

GP100

Ball

1LE22111CB113GA3

620

GP2

3.2

90.2

105

3

1200

213TC

208-230/460

GP100

Ball

1LE22112AC114GA3

813

GP2

4.3

90.2

150

3

1200

213TC

575

GP100

Ball

1LE22112AC113GA3

813

GP2

3.44

90.2

150

5

3600

184TC

208-230/460

GP100

Ball

1LE22111CA314GA3

754

GP2

6.2

90.2

103

5

3600

184TC

575

GP100

Ball

1LE22111CA313GA3

754

GP2

4.96

90.2

103

5

1800

184TC

208-230/460

GP100

Ball

1LE22111CB314GA3

692

GP2

6.7

90.2

109

5

1800

184TC

575

GP100

Ball

1LE22111CB313GA3

692

GP2

5.36

90.2

109

5

1200

215TC

208-230/460

GP100

Ball

1LE22112AC214GA3

1161

GP2

6.8

90.2

163

5

1200

215TC

575

GP100

Ball

1LE22112AC213GA3

1161

GP2

5.44

90.2

163

7.5

3600

213TC

208-230/460

GP100

Ball

1LE22112AA114GA3

953

GP2

8.5

91.7

178

7.5

3600

213TC

575

GP100

Ball

1LE22112AA113GA3

953

GP2

6.8

91.7

178

7.5

1800

213TC

208-230/460

GP100

Ball

1LE22112AB114GA3

927

GP2

9.5

92.4

178

7.5

1800

213TC

575

GP100

Ball

1LE22112AB113GA3

927

GP2

7.6

92.4

178

7.5

1200

254TC

208-230/460

GP100

Ball

1LE22112BC114GA3

1558

GP2

10.5

92.4

307

7.5

1200

254TC

575

GP100

Ball

1LE22112BC113GA3

1558

GP2

8.4

92.4

307

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-8

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-9

NEMA PREMIUM Severe Duty

10

✔

NEMA PREMIUM General Purpose

5 5

✔

HIGH EFFICIENT P-Base Vertical

3600

✔

HIGH EFFICIENT Definite Purpose

1

✔

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Frame

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RPM

DE Bearing

GP100 (Cast Iron Frame)

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

GP100 (Cast Iron Frame)

Introduction

General Purpose - TEFC Motors

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose

RPM

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

✔

The new SD100 series of general purpose TEFC motors exceeds NEMA Premium® efficiency standards to signifigantly reduce operating costs and pay for themselves in a short period of time through energy savings. They are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications.

✔

Performance Specifications

Stock Model

C-Face, Horizontal, Footless - continued 10

3600

215TC

208-230/460

GP100

Ball

1LE22112AA214GA3

1105

GP2

11.5

91.7

185

10

3600

215TC

575

GP100

Ball

1LE22112AA213GA3

1105

GP2

9.2

91.7

185

10

1800

215TC

208-230/460

GP100

Ball

1LE22112AB214GA3

1105

GP2

12.5

92.4

185

10

1800

215TC

575

GP100

Ball

1LE22112AB213GA3

1105

GP2

10

92.4

185

10

1200

256TC

208-230/460

GP100

Ball

1LE22112BC214GA3

1808

GP2

13.5

92.4

307

10

1200

256TC

575

GP100

Ball

1LE22112BC213GA3

1808

GP2

10.8

92.4

307

15

3600

254TC

208-230/460

GP100

Ball

1LE22112BA114GA3

1515

GP2

17

92.4

279

15

3600

254TC

575

GP100

Ball

1LE22112BA113GA3

1515

GP2

13.6

92.4

279

15

1800

254TC

208-230/460

GP100

Ball

1LE22112BB114GA3

1482

GP2

19

93

268

1800

254TC

575

GP100

Ball

1LE22112BB113GA3

1482

GP2

15.2

93

268

3600

256TC

208-230/460

GP100

Ball

1LE22112BA214GA3

1840

GP2

23

92.4

303

20

3600

256TC

575

GP100

Ball

1LE22112BA213GA3

1840

GP2

18

92.4

303

20

1800

256TC

208-230/460

GP100

Ball

1LE22112BB214GA3

1755

GP2

25

93.6

311

20

1800

256TC

575

GP100

Ball

1LE22112BB213GA3

1755

GP2

20

93.6

311

✔ ✔

✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

• • • • • •

Features for Long Life

HIGH EFFICIENT Definite Purpose HIGH EFFICIENT P-Base Vertical

Bearings - Regreasable, oversized double shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. All motors are equipped with drive end and opposite drive end shaft V-ring slingers for added bearing protection. Provisions for Inpro/Seal® bearing isolators are standard on both ends.

Oversized Conduit Box - Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance - All cast iron construction, polycarbonate fan, zincplated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Internal surfaces coated with epoxy enamel. Modifiable - Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Specifications table begins on the next page

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

3-10

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-11

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT P-Base Vertical

Rotor - Siemens exclusive, leading edge, die cast copper rotor design provides industry leading efficiencies. Each die cast copper rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Lubrication - A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

HIGH EFFICIENT Definite Purpose

Frame & End Shields - Cast iron construction for exceptional structural integrity and corrosion resistance, equipped with integrally cast feet and condensation T-drains. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

• •

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800 or 1200 RPM 3 phase, 60 Hz; 208-230/460 and 575 volt operation Exceeds NEMA Premium® efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 143T through 256T frame

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Multi Speed

15 20

SD100

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Multi Speed

Severe Duty - TEFC Motors

GP100 (Cast Iron Frame) DE Bearing

Introduction

General Purpose - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty HIGH EFFICIENT Definite Purpose HIGH EFFICIENT P-Base Vertical NEMA PREMIUM General Purpose

Weight (lbs.)

1LE23111AA114AA3 1LE23111AA113AA3 1LE23111AB214AA3 1LE23111AB213AA3 1LE23111AC314AA3 1LE23111AC313AA3 1LE23111AA214AA3 1LE23111AA213AA3 1LE23111AB314AA3 1LE23111AB313AA3 1LE23111CC114AA3 1LE23111CC113AA3 1LE23111AA314AA3 1LE23111AA313AA3 1LE23111AB414AA3 1LE23111AB413AA3 1LE23111CC314AA3 1LE23111CC313AA3 1LE23111CA114AA3 1LE23111CA113AA3 1LE23111CB114AA3 1LE23111CB113AA3 1LE23112AC114AA3 1LE23112AC113AA3 1LE23111CA314AA3 1LE23111CA313AA3 1LE23111CB314AA3 1LE23111CB313AA3 1LE23112AC214AA3 1LE23112AC213AA3 1LE23112AA114AA3 1LE23112AA113AA3 1LE23112AB114AA3 1LE23112AB113AA3 1LE23112BC114AA3 1LE23112BC113AA3 1LE23112AA214AA3 1LE23112AA213AA3 1LE23112AB214AA3 1LE23112AB213AA3 1LE23112BC214AA3 1LE23112BC213AA3 1LE23112BA114AA3 1LE23112BA113AA3 1LE23112BB114AA3 1LE23112BB113AA3 1LE23112BA214AA3 1LE23112BA213AA3 1LE23112BB214AA3 1LE23112BB213AA3

453 453 423 423 525 525 453 453 469 469 592 592 542 542 517 517 662 662 610 610 572 572 807 807 755 755 669 669 1137 1137 912 912 907 907 1512 1512 1067 1067 1093 1093 1847 1847 1465 1465 1440 1440 1814 1814 1793 1793

SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2 SD2

2.6 2.08 1.5 1.2 1.6 1.28 1.9 1.52 2.1 1.68 2.4 1.92 2.6 2.08 2.8 2.24 3 2.4 3.8 3.04 4 3.2 4.3 3.44 6.2 4.96 6.7 5.36 6.8 5.44 8.5 6.8 9.5 7.6 10.5 8.4 11.5 9.2 12.5 10 13.5 10.8 17 13.6 19 15.2 23 18 25 20

87.5 87.5 86.5 86.5 84 84 87.5 87.5 87.5 87.5 87.5 87.5 88.5 88.5 87.5 87.5 88.5 88.5 89.5 89.5 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 91.7 91.7 92.4 92.4 92.4 92.4 91.7 91.7 92.4 92.4 92.4 92.4 92.4 92.4 93 93 92.4 92.4 93.6 93.6

80 80 81 81 81 81 80 80 81 81 117 117 80 80 81 81 127 127 121 121 125 125 170 170 123 123 129 129 184 184 191 191 198 198 336 336 196 196 206 206 337 337 309 309 297 297 333 333 341 341

Stock Model ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps*

1LE23111AA114GA3

523

SD2

2.6

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Horizontal, Footless 1

3600

143TC

208-230/460

SD100

Ball

87.5

80

1

3600

143TC

575

SD100

Ball

1LE23111AA113GA3

523

SD2

2.08

87.5

80

1

1800

143TC

208-230/460

SD100

Ball

1LE23111AB214GA3

494

SD2

1.5

86.5

81

1

1800

143TC

575

SD100

Ball

1LE23111AB213GA3

494

SD2

1.2

86.5

81

1

1200

145TC

208-230/460

SD100

Ball

1LE23111AC314GA3

595

SD2

1.6

84

81

1

1200

145TC

575

SD100

Ball

1LE23111AC313GA3

595

SD2

1.28

84

81

1.5

3600

143TC

208-230/460

SD100

Ball

1LE23111AA214GA3

523

SD2

1.9

87.5

80

1.5

3600

143TC

575

SD100

Ball

1LE23111AA213GA3

523

SD2

1.52

87.5

80

1.5

1800

145TC

208-230/460

SD100

Ball

1LE23111AB314GA3

540

SD2

2.1

87.5

81

1.5

1800

145TC

575

SD100

Ball

1LE23111AB313GA3

540

SD2

1.68

87.5

81

1.5

1200

182TC

208-230/460

SD100

Ball

1LE23111CC114GA3

696

SD2

2.4

87.5

117

1.5

1200

182TC

575

SD100

Ball

1LE23111CC113GA3

696

SD2

1.92

87.5

117

2

3600

145TC

208-230/460

SD100

Ball

1LE23111AA314GA3

612

SD2

2.6

88.5

80

2

3600

145TC

575

SD100

Ball

1LE23111AA313GA3

612

SD2

2.08

88.5

80

2

1800

145TC

208-230/460

SD100

Ball

1LE23111AB414GA3

587

SD2

2.8

87.5

81

2

1800

145TC

575

SD100

Ball

1LE23111AB413GA3

587

SD2

2.24

87.5

81

2

1200

184TC

208-230/460

SD100

Ball

1LE23111CC314GA3

765

SD2

3

88.5

127

2

1200

184TC

575

SD100

Ball

1LE23111CC313GA3

765

SD2

2.4

88.5

127

3

3600

182TC

208-230/460

SD100

Ball

1LE23111CA114GA3

714

SD2

3.8

89.5

121

3

3600

182TC

575

SD100

Ball

1LE23111CA113GA3

714

SD2

3.04

89.5

121

3

1800

182TC

208-230/460

SD100

Ball

1LE23111CB114GA3

676

SD2

4

90.2

125

3

1800

182TC

575

SD100

Ball

1LE23111CB113GA3

676

SD2

3.2

90.2

125

3

1200

213TC

208-230/460

SD100

Ball

1LE23112AC114GA3

911

SD2

4.3

90.2

170

3

1200

213TC

575

SD100

Ball

1LE23112AC113GA3

911

SD2

3.44

90.2

170

5

3600

184TC

208-230/460

SD100

Ball

1LE23111CA314GA3

859

SD2

6.2

90.2

123

5

3600

184TC

575

SD100

Ball

1LE23111CA313GA3

859

SD2

4.96

90.2

123

5

1800

184TC

208-230/460

SD100

Ball

1LE23111CB314GA3

773

SD2

6.7

90.2

129

5

1800

184TC

575

SD100

Ball

1LE23111CB313GA3

773

SD2

5.36

90.2

129

5

1200

215TC

208-230/460

SD100

Ball

1LE23112AC214GA3

1241

SD2

6.8

90.2

184

5

1200

215TC

575

SD100

Ball

1LE23112AC213GA3

1241

SD2

5.44

90.2

184

7.5

3600

213TC

208-230/460

SD100

Ball

1LE23112AA114GA3

1016

SD2

8.5

91.7

191

7.5

3600

213TC

575

SD100

Ball

1LE23112AA113GA3

1016

SD2

6.8

91.7

191

7.5

1800

213TC

208-230/460

SD100

Ball

1LE23112AB114GA3

1011

SD2

9.5

92.4

198

7.5

1800

213TC

575

SD100

Ball

1LE23112AB113GA3

1011

SD2

7.6

92.4

198

7.5

1200

254TC

208-230/460

SD100

Ball

1LE23112BC114GA3

1653

SD2

10.5

92.4

336

7.5

1200

254TC

575

SD100

Ball

1LE23112BC113GA3

1653

SD2

8.4

92.4

336

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

NEMA PREMIUM General Purpose

FL Nom. Eff. (%)

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-13

NEMA PREMIUM Severe Duty

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-12

HIGH EFFICIENT P-Base Vertical

FL Amps*

HIGH EFFICIENT Definite Purpose

Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball Ball

Multiplier Symbol

HIGH EFFICIENT Hazardous Duty

SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100 SD100

Part Number

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

Type

DE Bearing

SD100

HIGH EFFICIENT Severe Duty

HP RPM Frame Voltage Horizontal, Foot Mounted 1 3600 143T 208-230/460 1 3600 143T 575 1 1800 143T 208-230/460 1 1800 143T 575 1 1200 145T 208-230/460 1 1200 145T 575 1.5 3600 143T 208-230/460 1.5 3600 143T 575 1.5 1800 145T 208-230/460 1.5 1800 145T 575 1.5 1200 182T 208-230/460 1.5 1200 182T 575 2 3600 145T 208-230/460 2 3600 145T 575 2 1800 145T 208-230/460 2 1800 145T 575 2 1200 184T 208-230/460 2 1200 184T 575 3 3600 182T 208-230/460 3 3600 182T 575 3 1800 182T 208-230/460 3 1800 182T 575 3 1200 213T 208-230/460 3 1200 213T 575 5 3600 184T 208-230/460 5 3600 184T 575 5 1800 184T 208-230/460 5 1800 184T 575 5 1200 215T 208-230/460 5 1200 215T 575 7.5 3600 213T 208-230/460 7.5 3600 213T 575 7.5 1800 213T 208-230/460 7.5 1800 213T 575 7.5 1200 254T 208-230/460 7.5 1200 254T 575 10 3600 215T 208-230/460 10 3600 215T 575 10 1800 215T 208-230/460 10 1800 215T 575 10 1200 256T 208-230/460 10 1200 256T 575 15 3600 254T 208-230/460 15 3600 254T 575 15 1800 254T 208-230/460 15 1800 254T 575 20 3600 256T 208-230/460 20 3600 256T 575 20 1800 256T 208-230/460 20 1800 256T 575

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

SD100

Introduction

Severe Duty - TEFC Motors

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose

RPM

Frame

Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Horizontal, Footless - continued 10

3600

215TC

208-230/460

SD100

Ball

1LE23112AA214GA3

1171

SD2

11.5

91.7

196

10

3600

215TC

575

SD100

Ball

1LE23112AA213GA3

1171

SD2

9.2

91.7

196

10

1800

215TC

208-230/460

SD100

Ball

1LE23112AB214GA3

1197

SD2

12.5

92.4

206

10

1800

215TC

575

SD100

Ball

1LE23112AB213GA3

1197

SD2

10

92.4

206

10

1200

256TC

208-230/460

SD100

Ball

1LE23112BC214GA3

1988

SD2

13.5

92.4

337

10

1200

256TC

575

SD100

Ball

1LE23112BC213GA3

1988

SD2

10.8

92.4

337

15

3600

254TC

208-230/460

SD100

Ball

1LE23112BA114GA3

1605

SD2

17

92.4

309

15

3600

254TC

575

SD100

Ball

1LE23112BA113GA3

1605

SD2

13.6

92.4

309

1800

254TC

208-230/460

SD100

Ball

1LE23112BB114GA3

1580

SD2

19

93

297

1800

254TC

575

SD100

Ball

1LE23112BB113GA3

1580

SD2

15.2

93

297

20

3600

256TC

208-230/460

SD100

Ball

1LE23112BA214GA3

1955

SD2

23

92.4

333

20

3600

256TC

575

SD100

Ball

1LE23112BA213GA3

1955

SD2

18

92.4

333

20

1800

256TC

208-230/460

SD100

Ball

1LE23112BB214GA3

1934

SD2

25

93.6

341

20

1800

256TC

575

SD100

Ball

1LE23112BB213GA3

1934

SD2

20

93.6

341

✔ ✔ ✔

NEMA Premium® Efficiency TEFC motors are the motors that can pay for themselves through energy savings. According to NEMA, electric motors consume 10 to 25 times their purchase price in electricity each year of operation. It is easy to see that increases in motor efficiency can significantly reduce operating costs. These motors are ideal for severe operating atmospheres in applications such as chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical.

✔ ✔ ✔

•1 to 400 HP •1.15 service factor, 40ºC ambient •3600, 1800 or 1200 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, 460 volt 25 HP and above; 200 and 575 volt available •Meets or exceeds NEMA Premium™ Efficiencies •Class F insulation, Class B temperature rise •NEMA Design B, Continuous Duty •0.06 IPS vibration •143T through S449 frame

HIGH EFFICIENT Definite Purpose HIGH EFFICIENT P-Base Vertical

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. All motors are equipped with drive end and opposite drive end shaft V-ring slingers for added bearing protection. Provisions for Inpro/Seal® bearing isolators are standard on both ends. Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Specifications table begins on the next page

3-14

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-15

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion.

HIGH EFFICIENT P-Base Vertical

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for all frames.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

HIGH EFFICIENT Definite Purpose

Features for Long Life

Insulation – Proprietary inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

Performance Specifications

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Multi Speed

15 15

✔

RGZEESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Severe Duty

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Multi Speed

Severe Duty - TEFC

SD100 DE Bearing

Introduction

Severe Duty - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Voltage

Type

Part Number

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted - continued

3600

143T

230/460

RGZEESD

Ball

1LA01432ES21

410

SA-7EXSD

1.3

82.5

58

✔

20

3600

256T

230/460

RGZEESD

Ball

1LA02562ES21

1646

SA-7EXSD

23

91

275

✔

1

3600

143T

575

RGZEESD

Ball

1LA01432ES51

410

SA-7EXSD

1.04

82.5

58

✔

20

3600

256T

575

RGZEESD

Ball

1LA02562ES51

1646

SA-7EXSD

18.4

91

275

✔

1

1800

143T

230/460

RGZEESD

Ball

1LA01444ES21

384

SA-7EXSD

1.5

85.5

62

✔

20

1800

256T

230/460

RGZEESD

Ball

1LA02564ES21

1627

SA-7EXSD

24

93

340

✔

1

1800

143T

575

RGZEESD

Ball

1LA01444ES51

384

SA-7EXSD

1.2

85.5

62

✔

20

1800

256T

575

RGZEESD

Ball

1LA02564ES51

1627

SA-7EXSD

19.2

93

340

✔

1

1200

145T

230/460

RGZEESD

Ball

1LA01456ES21

476

SA-7EXSD

1.6

82.5

64

✔

20

1200

286T

230/460

RGZEESD

Ball

1LA02866ES21

2707

SA-7EXSD

27

91.7

465

✔

1

1200

145T

575

RGZEESD

Ball

1LA01456ES51

476

SA-7EXSD

1.28

82.5

64

✔

20

1200

286T

575

RGZEESD

Ball

1LA02866ES51

2707

SA-7EXSD

21.6

91.7

465

✔

1.5

3600

143T

230/460

RGZEESD

Ball

1LA01442ES21

410

SA-7EXSD

1.9

85.5

60

✔

25

3600

284TS

460

RGZEESD

Ball

1LA02842ES42

2029

SA-7EXSD

29

91.7

415

✔

1.5

3600

143T

575

RGZEESD

Ball

1LA01442ES51

410

SA-7EXSD

1.52

85.5

60

✔

25

3600

284TS

575

RGZEESD

Ball

1LA02842ES52

2029

SA-7EXSD

23.2

91.7

415

✔

1.5

1800

145T

230/460

RGZEESD

Ball

1LA01454ES21

426

SA-7EXSD

2.2

86.5

65

✔

25

1800

284TS

460

RGZEESD

Ball

1LA02844ES42

1936

SA-7EXSD

30

93.6

445

✔

1.5

1800

145T

575

RGZEESD

Ball

1LA01454ES51

426

SA-7EXSD

1.76

86.5

65

✔

25

1800

284T

460

RGZEESD

Ball

1LA02844ES41

1936

SA-7EXSD

30

93.6

445

✔

1.5

1200

182T

230/460

RGZEESD

Ball

1LA01826ES21

537

SA-7EXSD

2.3

87.5

113

✔

25

1800

284TS

575

RGZEESD

Ball

1LA02844ES52

1936

SA-7EXSD

24

93.6

445

✔

1.5

1200

182T

575

RGZEESD

Ball

1LA01826ES51

537

SA-7EXSD

1.84

87.5

113

✔

25

1800

284T

575

RGZEESD

Ball

1LA02844ES51

1936

SA-7EXSD

24

93.6

445

✔

2

3600

145T

230/460

RGZEESD

Ball

1LA01452ES21

491

SA-7EXSD

2.4

86.5

67

✔

25

1200

324T

460

RGZEESD

Ball

1LA03246ES41

3189

SA-7EXSD

33

93

640

✔

2

3600

145T

575

RGZEESD

Ball

1LA01452ES51

491

SA-7EXSD

1.92

86.5

67

✔

25

1200

324T

575

RGZEESD

Ball

1LA03246ES51

3189

SA-7EXSD

26.4

93

640

✔

2

1800

145T

230/460

RGZEESD

Ball

1LA01464ES21

469

SA-7EXSD

2.8

86.5

69

✔

30

3600

286TS

460

RGZEESD

Ball

1LA02862ES42

2369

SA-7EXSD

34

91.7

430

✔

2

1800

145T

575

RGZEESD

Ball

1LA01464ES51

469

SA-7EXSD

2.24

86.5

69

✔

30

3600

286TS

575

RGZEESD

Ball

1LA02862ES52

2369

SA-7EXSD

27.2

91.7

430

✔

2

1200

184T

230/460

RGZEESD

Ball

1LA01846ES21

600

SA-7EXSD

2.9

88.5

126

✔

30

1800

286TS

460

RGZEESD

Ball

1LA02864ES42

2253

SA-7EXSD

35

93.6

465

✔

2

1200

184T

575

RGZEESD

Ball

1LA01846ES51

600

SA-7EXSD

2.32

88.5

126

✔

30

1800

286T

460

RGZEESD

Ball

1LA02864ES41

2253

SA-7EXSD

35

93.6

465

✔

3

3600

182T

230/460

RGZEESD

Ball

1LA01822ES21

553

SA-7EXSD

3.6

86.5

82

✔

30

1800

286TS

575

RGZEESD

Ball

1LA02864ES52

2253

SA-7EXSD

28

93.6

465

✔

3

3600

182T

575

RGZEESD

Ball

1LA01822ES51

553

SA-7EXSD

2.88

86.5

82

✔

30

1800

286T

575

RGZEESD

Ball

1LA02864ES51

2253

SA-7EXSD

28

93.6

465

✔

3

1800

182T

230/460

RGZEESD

Ball

1LA01824ES21

519

SA-7EXSD

4

89.5

113

✔

30

1200

326T

460

RGZEESD

Ball

1LA03266ES41

3778

SA-7EXSD

39

93

675

✔

3

1800

182T

575

RGZEESD

Ball

1LA01824ES51

519

SA-7EXSD

3.2

89.5

113

✔

30

1200

326T

575

RGZEESD

Ball

1LA03266ES51

3778

SA-7EXSD

31.2

93

675

✔

3

1200

213T

230/460

RGZEESD

Ball

1LA02136ES21

732

SA-7EXSD

4.3

89.5

188

✔

40

3600

324TS

460

RGZEESD

Ball

1LA03242ES42

3125

SA-7EXSD

45

93.6

575

✔

3

1200

213T

575

RGZEESD

Ball

1LA02136ES51

732

SA-7EXSD

3.44

89.5

188

✔

40

3600

324TS

575

RGZEESD

Ball

1LA03242ES52

3125

SA-7EXSD

36

93.6

575

✔

5

3600

184T

230/460

RGZEESD

Ball

1LA01842ES21

685

SA-7EXSD

5.7

88.5

95

✔

40

1800

324TS

460

RGZEESD

Ball

1LA03244ES42

2992

SA-7EXSD

46

94.1

666

✔

5

3600

184T

575

RGZEESD

Ball

1LA01842ES51

685

SA-7EXSD

4.56

88.5

95

✔

40

1800

324T

460

RGZEESD

Ball

1LA03244ES41

2992

SA-7EXSD

46

94.1

666

✔

5

1800

184T

230/460

RGZEESD

Ball

1LA01844ES21

607

SA-7EXSD

6.4

89.5

126

✔

40

1800

324TS

575

RGZEESD

Ball

1LA03244ES52

2992

SA-7EXSD

36.8

94.1

666

✔

5

1800

184T

575

RGZEESD

Ball

1LA01844ES51

607

SA-7EXSD

5.12

89.5

126

✔

40

1800

324T

575

RGZEESD

Ball

1LA03244ES51

2992

SA-7EXSD

36.8

94.1

666

✔

5

1200

215T

230/460

RGZEESD

Ball

1LA02156ES21

1031

SA-7EXSD

6.9

89.5

206

✔

40

1200

364T

460

RGZEESD

Ball

1LA03646ES41

5123

SA-7EXSD

49

94.1

863

✔

215T

575

RGZEESD

Ball

1LA02156ES51

1031

SA-7EXSD

5.52

89.5

206

✔

40

1200

364T

575

RGZEESD

Ball

5123

SA-7EXSD

39.2

94.1

863

213T

230/460

RGZEESD

Ball

1LA02132ES21

828

SA-7EXSD

8.6

89.5

146

✔

50

3600

326TS

460

RGZEESD

Ball

1LA03262ES42

4043

SA-7EXSD

55

93.6

610

✔

7.5

3600

213T

575

RGZEESD

Ball

1LA02132ES51

828

SA-7EXSD

6.88

89.5

146

✔

50

3600

326TS

575

RGZEESD

Ball

1LA03262ES52

4043

SA-7EXSD

44

93.6

610

✔

7.5

1800

213T

230/460

RGZEESD

Ball

1LA02134ES21

823

SA-7EXSD

9.5

91.7

205

✔

50

1800

326TS

460

RGZEESD

Ball

1LA03264ES42

3675

SA-7EXSD

58

94.5

700

✔

7.5

1800

213T

575

RGZEESD

Ball

1LA02134ES51

823

SA-7EXSD

7.6

91.7

205

✔

50

1800

326T

460

RGZEESD

Ball

1LA03264ES41

3675

SA-7EXSD

58

94.5

700

✔

7.5

1200

254T

230/460

RGZEESD

Ball

1LA02546ES21

1371

SA-7EXSD

10.5

91

290

✔

50

1800

326TS

575

RGZEESD

Ball

1LA03264ES52

3675

SA-7EXSD

46.4

94.5

700

✔

7.5

1200

254T

575

RGZEESD

Ball

1LA02546ES51

1371

SA-7EXSD

8.4

91

290

✔

50

1800

326T

575

RGZEESD

Ball

1LA03264ES51

3675

SA-7EXSD

46.4

94.5

700

✔

10

3600

215T

230/460

RGZEESD

Ball

1LA02152ES21

968

SA-7EXSD

11.4

90.2

164

✔

50

1200

365T

460

RGZEESD

Ball

1LA03656ES41

5882

SA-7EXSD

62

94.1

900

✔

5882

SA-7EXSD

49.6

94.1

900

1LA03642ES42

5318

SA-7EXSD

68

93.6

717

5318

SA-7EXSD

54.4

93.6

717

10

3600

215T

575

RGZEESD

Ball

1LA02152ES51

968

SA-7EXSD

90.2

164

✔

50

1200

365T

575

RGZEESD

Ball

10

1800

215T

230/460

RGZEESD

Ball

1LA02154ES21

991

SA-7EXSD

12.5

91.7

222

✔

60

3600

364TS

460

RGZEESD

Ball

10

1800

215T

575

RGZEESD

Ball

1LA02154ES51

991

SA-7EXSD

10

91.7

222

✔

60

3600

364TS

575

RGZEESD

Ball

9.12

✔

10

1200

256T

230/460

RGZEESD

Ball

1LA02566ES21

1675

SA-7EXSD

13.8

91

310

✔

60

1800

364TS

460

RGZEESD

Ball

1LA03644ES42

5272

SA-7EXSD

68

95

930

✔

10

1200

256T

575

RGZEESD

Ball

1LA02566ES51

1675

SA-7EXSD

11.04

91

310

✔

60

1800

364T

460

RGZEESD

Ball

1LA03644ES41

5272

SA-7EXSD

68

95

930

✔ ✔

3600

254T

230/460

RGZEESD

Ball

1LA02542ES21

1329

SA-7EXSD

17

91

251

✔

60

1800

364TS

575

RGZEESD

Ball

1LA03644ES52

5272

SA-7EXSD

54.4

95

930

3600

254T

575

RGZEESD

Ball

1LA02542ES51

1329

SA-7EXSD

13.6

91

251

✔

60

1800

364T

575

RGZEESD

Ball

1LA03644ES51

5272

SA-7EXSD

54.4

95

930

✔

15

1800

254T

230/460

RGZEESD

Ball

1LA02544ES21

1306

SA-7EXSD

19

92.4

315

✔

60

1200

404T

460

RGZEESD

Ball

1LA04046ES41

6892

SA-7EXSD

74

94.5

1100

✔

60

1200

404T

575

RGZEESD

Ball

6892

SA-7EXSD

59.2

94.5

1100

15

1800

254T

575

RGZEESD

Ball

1LA02544ES51

1306

SA-7EXSD

15.2

92.4

315

✔

15

1200

284T

230/460

RGZEESD

Ball

1LA02846ES21

2222

SA-7EXSD

21

91.7

400

✔

15

1200

284T

575

RGZEESD

Ball

1LA02846ES51

2222

SA-7EXSD

16.8

91.7

400

✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-16

2007 Low Voltage AC Motors Selection and Pricing Guide

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD100.

Shaded ratings will be discontinued when stock is depleted. Replaced by type SD100.

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-17

NEMA PREMIUM Severe Duty

15 15

NEMA PREMIUM General Purpose

1200 3600

HIGH EFFICIENT P-Base Vertical

5 7.5

HIGH EFFICIENT Definite Purpose

1

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Frame

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RPM

DE Bearing

RGZEESD

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

RGZEESD

Introduction

Severe Duty - TEFC

Severe Duty - TEFC

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

Voltage

Type

Part Number

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

1LA03652ES42

6678

SA-7EXSD

85

94.1

815

6678

SA-7EXSD

68

94.1

815

Stock Model

Horizontal, Foot Mounted - continued

HP

RPM

Frame

Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

1LA04472ES42

17776

SA-7EXSD

FL Nom. Eff. (%)

Weight (lbs.)

216

95.4

1890

FL Amps*

Stock Model

Horizontal, Foot Mounted - continued ✔

3600

365TS

460

RGZEESD

Ball

75

3600

365TS

575

RGZEESD

Ball

75

1800

365TS

460

RGZEESD

Ball

1LA03654ES42

6683

SA-7EXSD

85

95.4

1000

✔

75

1800

365T

460

RGZEESD

Ball

1LA03654ES41

6683

SA-7EXSD

85

95.4

1000

75

1800

365TS

575

RGZEESD

Ball

1LA03654ES52

6683

SA-7EXSD

68

95.4

75

1800

365T

575

RGZEESD

Ball

1LA03654ES51

6683

SA-7EXSD

68

75

1200

405T

460

RGZEESD

Ball

1LA04056ES41

8114

SA-7EXSD

75

1200

405T

575

RGZEESD

Ball

8114

SA-7EXSD

100 3600

405TS

460

RGZEESD

Ball

8949

SA-7EXSD

100 3600

405TS

575

RGZEESD

Ball

8949

SA-7EXSD

100 1800

405TS

460

RGZEESD

Ball

1LA04054ES42

8257

SA-7EXSD

100 1800

405T

460

RGZEESD

Ball

1LA04054ES41

8257

SA-7EXSD

100 1800

405TS

575

RGZEESD

Ball

8257

SA-7EXSD

100 1800

405T

575

RGZEESD

Ball

1LA04054ES51

8257

SA-7EXSD

100 1200

444TS

460

RGZEESD

Ball

1LA04446ES42

11090

SA-7EXSD

100 1200

444T

460

RGZEESD

Roller

1LA04446ES41

11090

100 1200

B444T

460

RGZEESD

Ball

1LA04446ES4N

100 1200

444TS

575

RGZEESD

Ball

100 1200

444T

575

RGZEESD

100 1200

B444T

575

125 3600

444TS

125 3600

444TS

125 1800 125 1800 125 1800

✔

447TS

460

RGZEESD

Ball

200 3600

447TS

575

RGZEESD

Ball

17776

SA-7EXSD

172.8

95.4

1890

200 1800

447TS

460

RGZEESD

Ball

1LA04474ES42

15371

SA-7EXSD

226

96.2

2035

✔

✔

200 1800

447T

460

RGZEESD

Roller

1LA04474ES41

15371

SA-7EXSD

226

96.2

2035

✔

1000

✔

200 1800

B447T

460

RGZEESD

Ball

1LA04474ES4N

15371

SA-7EXSD

226

96.2

2035

✔

95.4

1000

✔

200 1800

447TS

575

RGZEESD

Ball

1LA04474ES52

15371

SA-7EXSD

180.8

96.2

2035

✔

93

94.5

1150

✔

200 1800

447T

575

RGZEESD

Roller

1LA04474ES51

15371

SA-7EXSD

180.8

96.2

2035

✔

74.4

94.5

1150

200 1800

B447T

575

RGZEESD

Ball

1LA04474ES5N

15371

SA-7EXSD

180.8

96.2

2035

✔

94.1

1100

200 1200

449TS

460

RGZEESD

Ball

1LA04496ES42

18656

SA-7EXSD

227

95.8

2425

✔

94.1

1100

200 1200

449T

460

RGZEESD

Roller

1LA04496ES41

18656

SA-7EXSD

227

95.8

2425

✔

113

95.4

1160

✔

200 1200

B449T

460

RGZEESD

Ball

1LA04496ES4N

18656

SA-7EXSD

227

95.8

2425

✔

113

95.4

1160

✔

200 1200

449TS

575

RGZEESD

Ball

18656

SA-7EXSD

181.6

95.8

2425

90.4

95.4

1160

200 1200

449T

575

RGZEESD

Roller

18656

SA-7EXSD

181.6

95.8

2425

90.4

95.4

1160

✔

200 1200

B449T

575

RGZEESD

Ball

18656

SA-7EXSD

181.6

95.8

2425

117

95

1545

✔

250 3600

449TS

460

RGZEESD

Ball

22419

SA-7EXSD

269

95.8

2272

SA-7EXSD

117

95

1545

✔

250 3600

449TS

575

RGZEESD

Ball

22419

SA-7EXSD

215.2

95.8

2272

11090

SA-7EXSD

117

95

1545

✔

250 1800

449TS

460

RGZEESD

Ball

1LA04494ES42

19284

SA-7EXSD

281

96.2

2425

✔

11090

SA-7EXSD

93.6

95

1545

250 1800

449T

460

RGZEESD

Roller

1LA04494ES41

19284

SA-7EXSD

281

96.2

2425

✔

Roller

11090

SA-7EXSD

93.6

95

1545

250 1800

B449T

460

RGZEESD

Ball

1LA04494ES4N

19284

SA-7EXSD

281

96.2

2425

✔

RGZEESD

Ball

11090

SA-7EXSD

93.6

95

1545

250 1800

449TS

575

RGZEESD

Ball

19284

SA-7EXSD

224.8

96.2

2425

460

RGZEESD

Ball

11697

SA-7EXSD

138

95

1454

250 1800

449T

575

RGZEESD

Roller

19284

SA-7EXSD

224.8

96.2

2425

575

RGZEESD

Ball

11697

SA-7EXSD

110.4

95

1454

250 1800

B449T

575

RGZEESD

Ball

19284

SA-7EXSD

224.8

96.2

2425

444TS

460

RGZEESD

Ball

1LA04444ES42

10870

SA-7EXSD

143

95.4

1600

✔

250 1200

449TS

460

RGZEESD

Ball

1LA04496HS42

20301

SA-7EXSD

281

95.8

2390

✔

444T

460

RGZEESD

Roller

1LA04444ES41

10870

SA-7EXSD

143

95.4

1600

✔

250 1200

449T

460

RGZEESD

Roller

1LA04496HS41

20301

SA-7EXSD

281

95.8

2390

✔

B444T

460

RGZEESD

Ball

1LA04444ES4N

10870

SA-7EXSD

143

95.4

1600

✔

250 1200

B449T

460

RGZEESD

Ball

1LA04496HS4N

20301

SA-7EXSD

281

95.8

2390

✔

125 1800

444TS

575

RGZEESD

Ball

10870

SA-7EXSD

114.4

95.4

1600

250 1200

449TS

575

RGZEESD

Ball

20301

SA-7EXSD

224.8

95.8

2390

125 1800

444T

575

RGZEESD

Roller

1LA04444ES51

10870

SA-7EXSD

114.4

95.4

1600

✔

250 1200

449T

575

RGZEESD

Roller

20301

SA-7EXSD

224.8

95.8

2390

125 1800

B444T

575

RGZEESD

Ball

1LA04444ES5N

10870

SA-7EXSD

114.4

95.4

1600

✔

250 1200

B449T

575

RGZEESD

Ball

20301

SA-7EXSD

224.8

95.8

2390

125 1200

445TS

460

RGZEESD

Ball

1LA04456ES42

13621

SA-7EXSD

144

95

1720

✔

300 3600

449TS

460

RGZEESD

Ball

27898

SA-7EXSD

323

95.8

2200

125 1200

445T

460

RGZEESD

Roller

1LA04456ES41

13621

SA-7EXSD

144

95

1720

✔

300 3600

449TS

575

RGZEESD

Ball

27898

SA-7EXSD

258.4

95.8

2200

125 1200

B445T

460

RGZEESD

Ball

1LA04456ES4N

13621

SA-7EXSD

144

95

1720

✔

300 1800

449TS

460

RGZEESD

Ball

1LA04494HS42

20445

SA-7EXSD

346

96.2

3130

✔

125 1200

445TS

575

RGZEESD

Ball

13621

SA-7EXSD

115.2

95

1720

300 1800

449T

460

RGZEESD

Roller

1LA04494HS41

20445

SA-7EXSD

346

96.2

3130

✔

125 1200

445T

575

RGZEESD

Roller

13621

SA-7EXSD

115.2

95

1720

300 1800

B449T

460

RGZEESD

Ball

1LA04494HS4N

20445

SA-7EXSD

346

96.2

3130

✔

125 1200

B445T

575

RGZEESD

Ball

13621

SA-7EXSD

115.2

95

1720

300 1800

449TS

575

RGZEESD

Ball

20445

SA-7EXSD

276.8

96.2

3130

150 3600

445TS

460

RGZEESD

Ball

14052

SA-7EXSD

164

95

1615

300 1800

449T

575

RGZEESD

Roller

20445

SA-7EXSD

276.8

96.2

3130

150 3600

445TS

575

RGZEESD

Ball

14052

SA-7EXSD

131.2

95

1615

300 1800

B449T

575

RGZEESD

Ball

20445

SA-7EXSD

276.8

96.2

3130

150 1800

445TS

460

RGZEESD

Ball

1LA04454ES42

12637

SA-7EXSD

170

95.8

1710

✔

300 1200

S449LS

460

RGZEESD

Roller

37844

SA-7EXSD

342

95.8

3240

150 1800

445T

460

RGZEESD

Roller

1LA04454ES41

12637

SA-7EXSD

170

95.8

1710

✔

300 1200

S449LS

575

RGZEESD

37844

SA-7EXSD

273.6

95.8

3240

150 1800

B445T

460

RGZEESD

Ball

1LA04454ES4N

12637

SA-7EXSD

170

95.8

1710

✔

350 3600

S449SS

460

RGZEESD

Roller Ball 1

35044

SA-7EXSD

372

95.8

2890

150 1800

445TS

575

RGZEESD

Ball

1LA04454ES52

12637

SA-7EXSD

136

95.8

1710

✔

350 3600

S449SS

575

RGZEESD

Ball 1

35044

SA-7EXSD

297.6

95.8

2890

150 1800

445T

575

RGZEESD

Roller

1LA04454ES51

12637

SA-7EXSD

136

95.8

1710

✔

350 1800

S449SS

460

RGZEESD

Ball

1LA03504ES42

32449

SA-7EXSD

392

96.2

3190

✔

150 1800

B445T

575

RGZEESD

Ball

1LA04454ES5N

12637

SA-7EXSD

136

95.8

1710

✔

350 1800

S449LS

460

RGZEESD

Roller

1LA03504ES41

32449

SA-7EXSD

392

96.2

3190

✔

150 1200

447TS

460

RGZEESD

Ball

1LA04476ES42

15240

SA-7EXSD

172

95.8

1995

✔

350 1800

S449SS

575

RGZEESD

Ball

32449

SA-7EXSD

313.6

96.2

3190

150 1200

447T

460

RGZEESD

Roller

1LA04476ES41

15240

SA-7EXSD

172

95.8

1995

✔

350 1800

S449LS

575

RGZEESD

Roller

32449

SA-7EXSD

313.6

96.2

3190

150 1200

B447T

460

RGZEESD

Ball

1LA04476ES4N

15240

SA-7EXSD

172

95.8

1995

✔

150 1200

447TS

575

RGZEESD

Ball

15240

SA-7EXSD

137.6

95.8

1995

150 1200

447T

575

RGZEESD

Roller

15240

SA-7EXSD

137.6

95.8

1995

150 1200

B447T

575

RGZEESD

Ball

15240

SA-7EXSD

137.6

95.8

1995

1LA04052ES42

1LA04442ES42

1LA04452ES42

108 86.4

✔

✔

✔

1LA04492ES42

1LA04494ES51

1LA04492HS42

1LA03006ES41

✔

✔

✔ ✔

*FL Amps are at 460V or 575V depending on the voltage rating of the motor.

3-18

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-19

NEMA PREMIUM Severe Duty

*FL Amps are at 460V or 575V depending on the voltage rating of the motor. 1 CW rotation facing opposite drive end.

NEMA PREMIUM General Purpose

1LA03502ES42

✔

HIGH EFFICIENT P-Base Vertical

200 3600

HIGH EFFICIENT Definite Purpose

75

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

Frame

List Price $

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RPM

DE Bearing

RGZEESD

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

HP

Stock/Modifiable

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

RGZEESD

Introduction

Severe Duty - TEFC

Severe Duty - TEFC

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

Frame

Voltage

Type

Weight (lbs.)

Stock Model ✔

Part Number

List Price $

Multiplier Symbol

FL Amps*

1LA04002ES42

39331

SA-7EXSD

422

95.8

3065

39331

SA-7EXSD

337.6

95.8

3065

Horizontal, Foot Mounted - continued 400 3600

S449SS

460

RGZEESD

400 3600

S449SS

575

RGZEESD

Ball 1 Ball 1

400 1800

S449SS

460

RGZEESD

Ball

1LA04004ES42

36427

SA-7EXSD

454

96.2

3240

✔

400 1800

S449LS

460

RGZEESD

Roller

1LA04004ES41

36427

SA-7EXSD

454

96.2

3240

✔

400 1800

S449SS

575

RGZEESD

Ball

36427

SA-7EXSD

363.2

96.2

400 1800

S449LS

575

RGZEESD

Roller

HP

RPM

Frame

Stock/Modifiable Voltage

Type

DE Bearing

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

2871

SA-7EXSD

34

91.7

450

C-Face, Vertical with Drip Cover, Footless - continued 30

3600

286TSCV

460

RGZVEESD

Ball

30

1800

286TCV

460

RGZVEESD

Ball

2761

SA-7EXSD

35

93

450

30

1200

326TCV

460

RGZVEESD

Ball

4406

SA-7EXSD

39

92.4

640

40

3600

324TSCV

460

RGZVEESD

Ball

3788

SA-7EXSD

45

93.6

565

3240

40

1800

324TCV

460

RGZVEESD

Ball

3663

SA-7EXSD

47

93.6

565

1200

364TCV

460

RGZVEESD

Ball

6279

SA-7EXSD

52

93.6

830

36427

SA-7EXSD

363.2

96.2

3240

40 50

3600

326TSCV

460

RGZVEESD

Ball

4654

SA-7EXSD

55

93.6

640

1

1800

143TCV

230/460

RGZVEESD Ball

680

SA-7EXSD

1.5

82.5

45

50

1800

326TCV

460

RGZVEESD

Ball

4307

SA-7EXSD

58

93.6

640

1

1200

145TCV

230/460

RGZVEESD Ball

767

SA-7EXSD

1.8

80

55

50

1200

365TCV

460

RGZVEESD

Ball

6995

SA-7EXSD

66

93.6

850

1.5

3600

143TCV

230/460

RGZVEESD Ball

705

SA-7EXSD

2

82.5

45

60

3600

364TSCV

460

RGZVEESD

Ball

6463

SA-7EXSD

68

93.6

830

1.5

1800

145TCV

230/460

RGZVEESD Ball

720

SA-7EXSD

2.2

84

55

60

1800

364TCV

460

RGZVEESD

Ball

6420

SA-7EXSD

71

93.6

830

1.5

1200

182TCV

230/460

RGZVEESD Ball

825

SA-7EXSD

2.3

85.5

85

2

3600

145TCV

230/460

RGZVEESD Ball

781

SA-7EXSD

2.5

84

55

60

1200

404TCV

460

RGZVEESD

Ball

8618

SA-7EXSD

74

94.1

1100

2

1800

145TCV

230/460

RGZVEESD Ball

760

SA-7EXSD

2.9

84

55

75

3600

365TSCV

460

RGZVEESD

Ball

7746

SA-7EXSD

85

94.1

850

75

1800

365TSCV

460

RGZVEESD

Ball

7751

SA-7EXSD

87

94.1

850

C-Face, Vertical with Drip Cover, Footless

2

1200

184TCV

230/460

RGZVEESD Ball

884

SA-7EXSD

3

86.5

100

3

3600

182TCV

230/460

RGZVEESD Ball

840

SA-7EXSD

3.6

86.5

85

75

1800

365TCV

460

RGZVEESD

Ball

7751

SA-7EXSD

87

94.1

850

75

1200

405TCV

460

RGZVEESD

Ball

9771

SA-7EXSD

93

94.5

1250

1800

182TCV

230/460

RGZVEESD Ball

808

SA-7EXSD

3.9

87.5

85

3

1200

213TCV

230/460

RGZVEESD Ball

1009

SA-7EXSD

4

87.5

130

100 3600

405TSCV

460

RGZVEESD

Ball

10558

SA-7EXSD

108

94.1

1250

5

3600

184TCV

230/460

RGZVEESD Ball

964

SA-7EXSD

5.8

87.5

100

100 1800

405TSCV

460

RGZVEESD

Ball

9906

SA-7EXSD

113

94.5

1250

5

1800

184TCV

230/460

RGZVEESD Ball

891

SA-7EXSD

6.5

87.5

100

100 1800

405TCV

460

RGZVEESD

Ball

9906

SA-7EXSD

113

94.5

1250

5

1200

215TCV

230/460

RGZVEESD Ball

1291

SA-7EXSD

6.8

88.5

162

100 1200

444TSCV

460

RGZVEESD

Ball

13802

SA-7EXSD

117

94.5

1620

7.5

3600

213TCV

230/460

RGZVEESD Ball

1099

SA-7EXSD

8.8

88.5

130

100 1200

444TCV

460

RGZVEESD

Ball

13802

SA-7EXSD

117

94.5

1620

213TCV

230/460

RGZVEESD Ball

1094

SA-7EXSD

9.5

89.5

130

254TCV

230/460

RGZVEESD Ball

1719

SA-7EXSD

9.8

90.2

250

10

3600

215TCV

230/460

RGZVEESD Ball

1231

SA-7EXSD

12

89.5

162

10

1800

215TCV

230/460

RGZVEESD Ball

1253

SA-7EXSD

13

89.5

162

10

1200

256TCV

230/460

RGZVEESD Ball

2006

SA-7EXSD

13

90.2

295

15

3600

254TCV

230/460

RGZVEESD Ball

1680

SA-7EXSD

17

90.2

250

15

1800

254TCV

230/460

RGZVEESD Ball

1658

SA-7EXSD

19

91.7

250

150 3600

15

1200

284TCV

230/460

RGZVEESD Ball

2732

SA-7EXSD

20

91

380

20

3600

256TCV

230/460

RGZVEESD Ball

1979

SA-7EXSD

23

90.2

295

20

1800

256TCV

230/460

RGZVEESD Ball

1961

SA-7EXSD

26

91.7

295

20

1200

286TCV

230/460

RGZVEESD Ball

3190

SA-7EXSD

26

91.7

450

3600

284TSCV 460

RGZVEESD Ball

2550

SA-7EXSD

29

91.7

380

25

1800

284TCV

460

RGZVEESD Ball

2734

SA-7EXSD

29

93

380

25

1200

324TCV

460

RGZVEESD Ball

3936

SA-7EXSD

33

92.4

565

*FL Amps are at 460V or 575V depending on the voltage rating of the motor. 1 CW rotation facing opposite drive end.

Shaded ratings will be discontinued when stock is depleted. Replaced by type SD100.

125 3600

444TSCV

460

RGZVEESD

Ball

13745

SA-7EXSD

138

94.5

1620

125 1800

444TSCV

460

RGZVEESD

Ball

13595

SA-7EXSD

143

95

1620

125 1800

444TCV

460

RGZVEESD

Ball

13595

SA-7EXSD

143

95

1620

125 1200

445TSCV

460

RGZVEESD

Ball

16190

SA-7EXSD

144

94.5

1740

125 1200

445TCV

460

RGZVEESD

Ball

16190

SA-7EXSD

144

94.5

1740

445TSCV

460

RGZVEESD

Ball

16867

SA-7EXSD

164

95

1740

150 1800

445TSCV

460

RGZVEESD

Ball

15262

SA-7EXSD

170

95.8

1740

150 1800

445TCV

460

RGZVEESD

Ball

15262

SA-7EXSD

170

95.8

1740

150 1200

447TSCV

460

RGZVEESD

Ball

17717

SA-7EXSD

170

95

2000

150 1200

447TCV

460

RGZVEESD

Ball

17717

SA-7EXSD

170

95

2000

200 3600

447TSCV

460

RGZVEESD

Ball

20110

SA-7EXSD

216

95

2000

200 1800

447TSCV

460

RGZVEESD

Ball

17841

SA-7EXSD

225

95.8

2000

200 1800

447TCV

460

RGZVEESD

Ball

17841

SA-7EXSD

225

95.8

2000

200 1200

449TCV

460

RGZVEESD

Ball

20940

SA-7EXSD

226

95

2300

HIGH EFFICIENT P-Base Vertical

1800 1200

HIGH EFFICIENT Definite Purpose

7.5 7.5

HIGH EFFICIENT Hazardous Duty

3

25

Stock Model

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RPM

DE Bearing

FL Nom. Eff. (%)

RGZEESD

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

HP

Stock/Modifiable

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

3-20

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-21

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

RGZEESD

Introduction

Severe Duty - TEFC

Severe Duty - TEFC

Introduction HIGH EFFICIENT General Purpose

HP

RPM

Frame

Stock/Modifiable Voltage

Type

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

C-Face, Vertical with Drip Cover, Footless - continued 250 3600 449TSCV

460

RGZVEESD

Ball

24490

SA-7EXSD

267

95.4

2300

250 1800 449TSCV

460

RGZVEESD

Ball

21532

SA-7EXSD

281

95.8

2300

250 1800 449TCV

460

RGZVEESD

Ball

21532

SA-7EXSD

281

95.8

2300

RGZVEESD

Ball

22492

SA-7EXSD

280

95

2300

460

RGZVEESD

Ball

22492

SA-7EXSD

280

95

2300

300 3600 449TSCV

460

RGZVEESD

Ball

29659

SA-7EXSD

323

95.8

2300

300 1800 449TSCV

460

RGZVEESD

Ball

22628

SA-7EXSD

346

95.4

2300

300 1800 449TCV

460

RGZVEESD

Ball

22628

SA-7EXSD

346

95

2300

• • • • • • •

HIGH EFFICIENT Hazardous Duty

• • •

1 to 20 HP 1.15 service factor, 40°C ambient 3600, 1800, 1200 or 900 RPM 3 phase, 60 Hz; 460 and 575 volt operation Exceeds IEEE 841-2001 standards Exceeds NEMA Premium® efficiency standards Class F insulation, Class B temperature rise @ 1.0SF NEMA Design B, Continuous Duty 0.06 IPS vibration / 0.005" foot flatness or better 143T through 256T frame

Features for Long Life

HIGH EFFICIENT Definite Purpose HIGH EFFICIENT P-Base Vertical

Modifiable - Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Lubrication - A specially formulated, high temperature tested grease is used to provide more than four times the lubrication life of other polyurea greases. Seamless, grease filled lubrication pipes are included.

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Bearings - Regreasable, oversized single shielded with cast iron inner caps. Alemite grease inlet fittings and automatic grease relief fittings for ease of routine maintenance. Inpro/Seal® bearing isolators are standard on both bearing housings.

Corrosion Resistance - Cast iron construction, polycarbonate fan, zincplated hardware, epoxy enamel paint and embossed stainless steel nameplate resist rust and corrosion. Internal surfaces coated with epoxy enamel.

HIGH EFFICIENT P-Base Vertical

Rotor - Siemens exclusive, leading edge, die cast copper rotor design provides industry leading efficiencies. Each die cast copper rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling - A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves air flow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Oversized Conduit Box - Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads.

Specifications table begins on the next page

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-23

NEMA PREMIUM Severe Duty

3-22

HIGH EFFICIENT Definite Purpose

Frame & End Shields - Cast iron construction for exceptional structural integrity and corrosion resistance, equipped with integrally cast feet and condensation T-drains. Lifting provisions are included for frames 180T to 256T. Unique frame fin design maximizes cooling.

Insulation - Proprietary inverter-rated NEMA Class F non-hygroscopic insulation system with Class B temperature rise @ 1.0SF, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HIGH EFFICIENT Hazardous Duty

NEMA PREMIUM Severe Duty

Performance Specifications

Stator/Windings - Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance and lowers stator losses.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Multi Speed

460

The new SD100 line of IEEE 841 motors exceeds IEEE 841-2001 standards for energy efficiency, high performance, variable speed operation, rugged construction and long service life for the most demanding applications. They are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications.

HIGH EFFICIENT Severe Duty

250 1200 449TSCV 250 1200 449TCV

SD100 IEEE841

HIGH EFFICIENT General Purpose

HIGH EFFICIENT Severe Duty

RGZEESD DE Bearing

Introduction

Severe Duty / IEEE 841 - TEFC Motors

Severe Duty - TEFC

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

1

3600

143T

460

Type SD100

Ball

Part Number

List Price $

Multiplier Symbol

FL Amps*

FL Nom. Eff. (%)

1LE24111AA112AA3

569

SD3

2.6

87.5

Weight (lbs.) 79

1

3600

143T

575

SD100

Ball

1LE24111AA113AA3

569

SD3

2.08

87.5

79

1

1800

143T

460

SD100

Ball

1LE24111AB212AA3

551

SD3

1.5

86.5

81

1

1800

143T

575

SD100

Ball

1LE24111AB213AA3

551

SD3

1.2

86.5

81

1

1200

145T

460

SD100

Ball

1LE24111AC312AA3

649

SD3

1.6

84

81

1

1200

145T

575

SD100

Ball

1LE24111AC313AA3

649

SD3

1.28

84

81

1

900

182T

460

SD100

Ball

1LE24111CD112AA3

948

SD3

2.1

81.5

106

1

900

182T

575

SD100

Ball

1LE24111CD113AA3

948

SD3

1.64

81.5

106

1.5

3600

143T

460

SD100

Ball

1LE24111AA212AA3

570

SD3

1.9

87.5

79

1.5

3600

143T

575

SD100

Ball

1LE24111AA213AA3

570

SD3

1.52

87.5

79

1.5

1800

145T

460

SD100

Ball

1LE24111AB312AA3

594

SD3

2.1

87.5

81

1.5

1800

145T

575

SD100

Ball

1LE24111AB313AA3

594

SD3

1.68

87.5

81

1.5

1200

182T

460

SD100

Ball

1LE24111CC112AA3

728

SD3

2.4

87.5

117

1.5

1200

182T

575

SD100

Ball

1LE24111CC113AA3

728

SD3

1.92

87.5

Ball

1LE24111CD312AA3

1119

SD3

3

82.5

119

SD100

Ball

1LE24111CD313AA3

1119

SD3

2.4

82.5

119

2

3600

145T

460

SD100

Ball

1LE24111AA312AA3

654

SD3

2.6

88.5

80

2

3600

145T

575

SD100

Ball

1LE24111AA313AA3

654

SD3

2.08

88.5

80

2

1800

145T

460

SD100

Ball

1LE24111AB412AA3

636

SD3

2.8

87.5

81

2

1800

145T

575

SD100

Ball

1LE24111AB413AA3

636

SD3

2.24

87.5

81

2

1200

184T

460

SD100

Ball

1LE24111CC312AA3

774

SD3

3

88.5

127

2

1200

184T

575

SD100

Ball

1LE24111CC313AA3

774

SD3

2.4

88.5

127

2

900

213T

460

SD100

Ball

1LE24112AD112AA3

1317

SD3

3.3

84

145

2

900

213T

575

SD100

Ball

1LE24112AD113AA3

1317

SD3

2.64

84

145

3

3600

182T

460

SD100

Ball

1LE24111CA112AA3

686

SD3

3.8

89.5

121

3

3600

182T

575

SD100

Ball

1LE24111CA113AA3

686

SD3

3.04

89.5

121

3

1800

182T

460

SD100

Ball

1LE24111CB112AA3

657

SD3

4

90.2

125

3

1800

182T

575

SD100

Ball

1LE24111CB113AA3

657

SD3

3.2

90.2

125

3

1200

213T

460

SD100

Ball

1LE24112AC112AA3

977

SD3

4.3

90.2

170

3

1200

213T

575

SD100

Ball

1LE24112AC113AA3

977

SD3

3.44

90.2

170

3

900

215T

460

SD100

Ball

1LE24112AD212AA3

1671

SD3

4.8

85.5

160

3

900

215T

575

SD100

Ball

1LE24112AD213AA3

1671

SD3

3.84

85.5

160

5

3600

184T

460

SD100

Ball

1LE24111CA312AA3

834

SD3

6.2

90.2

123

5

3600

184T

575

SD100

Ball

1LE24111CA313AA3

834

SD3

4.96

90.2

123

5

1800

184T

460

SD100

Ball

1LE24111CB312AA3

748

SD3

6.7

90.2

129

5

1800

184T

575

SD100

Ball

1LE24111CB313AA3

748

SD3

5.36

90.2

129

5

1200

215T

460

SD100

Ball

1LE24112AC212AA3

1285

SD3

6.8

90.2

184

5

1200

215T

575

SD100

Ball

1LE24112AC213AA3

1285

SD3

5.44

90.2

184

5

900

254T

460

SD100

Ball

1LE24112BD112AA3

2220

SD3

8.8

86.5

247

5

900

254T

575

SD100

Ball

1LE24112BD113AA3

2220

SD3

7.04

86.5

247

7.5

3600

213T

460

SD100

Ball

1LE24112AA112AA3

1029

SD3

8.5

91.7

191

7.5

3600

213T

575

SD100

Ball

1LE24112AA113AA3

1029

SD3

6.8

91.7

191

7.5

1800

213T

460

SD100

Ball

1LE24112AB112AA3

999

SD3

9.5

92.4

198

7.5

1800

213T

575

SD100

Ball

1LE24112AB113AA3

999

SD3

7.6

92.4

198

7.5

1200

254T

460

SD100

Ball

1LE24112BC112AA3

1653

SD3

10.5

92.4

336

7.5

1200

254T

575

SD100

Ball

1LE24112BC113AA3

1653

SD3

8.4

92.4

336

7.5

900

256T

460

SD100

Ball

1LE24112BD212AA3

2800

SD3

13

87.5

279

7.5

900

256T

575

SD100

Ball

1LE24112BD213AA3

2800

SD3

10.4

87.5

279

2007 Low Voltage AC Motors Selection and Pricing Guide

FL Nom. Eff. (%)

Weight (lbs.)

SD100

Ball

1LE24112AA212AA3

1182

SD3

11.5

91.7

196

3600

215T

575

SD100

Ball

1LE24112AA213AA3

1182

SD3

9.2

91.7

196

✔

10

1800

215T

460

SD100

Ball

1LE24112AB212AA3

1196

SD3

12.5

92.4

206

10

1800

215T

575

SD100

Ball

1LE24112AB213AA3

1196

SD3

10

92.4

206

✔

10

1200

256T

460

SD100

Ball

1LE24112BC212AA3

2056

SD3

13.5

92.4

337

10

1200

256T

575

SD100

Ball

1LE24112BC213AA3

2056

SD3

10.8

92.4

337

✔

15

3600

254T

460

SD100

Ball

1LE24112BA112AA3

1604

SD3

17

92.4

309

✔

15

3600

254T

575

SD100

Ball

1LE24112BA113AA3

1604

SD3

13.6

92.4

309

15

1800

254T

460

SD100

Ball

1LE24112BB112AA3

1575

SD3

19

93

297

15

1800

254T

575

SD100

Ball

1LE24112BB113AA3

1575

SD3

15.2

93

297

20

3600

256T

460

SD100

Ball

1LE24112BA212AA3

1969

SD3

23

92.4

333

✔ ✔ ✔

20

3600

256T

575

SD100

Ball

1LE24112BA213AA3

1969

SD3

18

92.4

333

20

1800

256T

460

SD100

Ball

1LE24112BB212AA3

2031

SD3

25

93.6

341

20

1800

256T

575

SD100

Ball

1LE24112BB213AA3

2031

SD3

20

93.6

341

Stock Model ✔ ✔ ✔ ✔ ✔ ✔ ✔

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-25

NEMA PREMIUM Severe Duty

SD100

575

FL Amps*

NEMA PREMIUM General Purpose

460

184T

Part Number

Multiplier Symbol

HIGH EFFICIENT P-Base Vertical

184T

900

Type

List Price $

HIGH EFFICIENT Definite Purpose

900

1.5

HP RPM Frame Voltage Horizontal, Foot Mounted - continued 10 3600 215T 460

DE Bearing

10

✔

117

1.5

3-24

Stock Model

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

HP RPM Frame Voltage Horizontal, Foot Mounted

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

SD100 IEEE841

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

SD100 IEEE841

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty / IEEE 841 - TEFC Motors

Introduction

Severe Duty / IEEE 841 - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

NEMA Premium® Efficiency IEEE 841 motors exceed IEEE 841-2001 standards for energy efficiency, high performance, variable speed operation, rugged construction and long service life for the most demanding applications. They are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications.

Performance Specifications

Features for Long Life

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease inlet fittings and automatic grease relief fittings for ease of routine maintenance. Inpro/Seal® bearing isolators are standard on both bearing housings. Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Seamless, grease filled lubrication pipes are included.

Type

Part Number

Weight (lbs.)

Stock Model

Horizontal, Foot Mounted

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and embossed stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

1

3600

143T

460

RGZEESDX

Ball

1LA01432EE41

516

SA-7IEE

1.3

82.5

58

1

3600

143T

575

RGZEESDX

Ball

1LA01432EE51

516

SA-7IEE

1.04

82.5

58

1

1800

143T

460

RGZEESDX

Ball

1LA01444EE41

500

SA-7IEE

1.5

85.5

62

1

1800

143T

575

RGZEESDX

Ball

1LA01444EE51

500

SA-7IEE

1.2

85.5

62

1

1200

145T

460

RGZEESDX

Ball

1LA01456EE41

589

SA-7IEE

1.6

82.5

64

1

1200

145T

575

RGZEESDX

Ball

1LA01456EE51

589

SA-7IEE

1.28

82.5

64

1

900

182T

460

RGZEESDX

Ball

1LA01828EE41

860

SA-7IEE

1.9

78.5

85

1

900

182T

575

RGZEESDX

Ball

1LA01828EE51

860

SA-7IEE

1.52

78.5

85

1.5

3600

143T

460

RGZEESDX

Ball

1LA01442EE41

517

SA-7IEE

1.9

85.5

60

1.5

3600

143T

575

RGZEESDX

Ball

1LA01442EE51

517

SA-7IEE

1.52

85.5

60

1.5

1800

145T

460

RGZEESDX

Ball

1LA01454EE41

539

SA-7IEE

2.2

86.5

65

1.5

1800

145T

575

RGZEESDX

Ball

1LA01454EE51

539

SA-7IEE

1.76

86.5

65

1.5

1200

182T

460

RGZEESDX

Ball

1LA01826EE41

660

SA-7IEE

2.3

87.5

113

1.5

1200

182T

575

RGZEESDX

Ball

1LA01826EE51

660

SA-7IEE

1.84

87.5

113

1.5

900

184T

460

RGZEESDX

Ball

1LA01848EE41

1015

SA-7IEE

2.8

80.0

86

1.5

900

184T

575

RGZEESDX

Ball

1LA01848EE51

1015

SA-7IEE

2.24

80.0

86

2

3600

145T

460

RGZEESDX

Ball

1LA01452EE41

593

SA-7IEE

2.4

86.5

67

2

3600

145T

575

RGZEESDX

Ball

1LA01452EE51

593

SA-7IEE

1.92

86.5

67

2

1800

145T

460

RGZEESDX

Ball

1LA01464EE41

577

SA-7IEE

2.8

86.5

69

2

1800

145T

575

RGZEESDX

Ball

1LA01464EE51

577

SA-7IEE

2.24

86.5

69

2

1200

184T

460

RGZEESDX

Ball

1LA01846EE41

702

SA-7IEE

2.9

88.5

126

2

1200

184T

575

RGZEESDX

Ball

1LA01846EE51

702

SA-7IEE

2.32

88.5

126

2

900

213T

460

RGZEESDX

Ball

1LA02138EE41

1194

SA-7IEE

3.2

84

123

2

900

213T

575

RGZEESDX

Ball

1LA02138EE51

1194

SA-7IEE

2.56

84

123

3

3600

182T

460

RGZEESDX

Ball

1LA01822EE41

622

SA-7IEE

3.6

86.5

82

3

3600

182T

575

RGZEESDX

Ball

1LA01822EE51

622

SA-7IEE

2.88

86.5

82

3

1800

182T

460

RGZEESDX

Ball

1LA01824EE41

596

SA-7IEE

4

89.5

113

3

1800

182T

575

RGZEESDX

Ball

1LA01824EE51

596

SA-7IEE

3.2

89.5

113

3

1200

213T

460

RGZEESDX

Ball

1LA02136EE41

886

SA-7IEE

4.3

89.5

188

3

1200

213T

575

RGZEESDX

Ball

1LA02136EE51

886

SA-7IEE

3.44

89.5

188

3

900

215T

460

RGZEESDX

Ball

1LA02158EE41

1515

SA-7IEE

4.5

85.5

149

3

900

215T

575

RGZEESDX

Ball

1LA02158EE51

1515

SA-7IEE

3.6

85.5

149

5

3600

184T

460

RGZEESDX

Ball

1LA01842EE41

756

SA-7IEE

5.7

88.5

95

5

3600

184T

575

RGZEESDX

Ball

1LA01842EE51

756

SA-7IEE

4.56

88.5

95

5

1800

184T

460

RGZEESDX

Ball

1LA01844EE41

678

SA-7IEE

6.4

89.5

126

5

1800

184T

575

RGZEESDX

Ball

1LA01844EE51

678

SA-7IEE

5.12

89.5

126

5

1200

215T

460

RGZEESDX

Ball

1LA02156EE41

1166

SA-7IEE

6.9

89.5

206

5

1200

215T

575

RGZEESDX

Ball

1LA02156EE51

1166

SA-7IEE

5.52

89.5

206

5

900

254T

460

RGZEESDX

Ball

1LA02548EE41

2013

SA-7IEE

7.5

86.5

235

5

900

254T

575

RGZEESDX

Ball

1LA02548EE51

2013

SA-7IEE

6

86.5

235

7.5

3600

213T

460

RGZEESDX

Ball

1LA02132EE41

933

SA-7IEE

8.6

89.5

146

7.5

3600

213T

575

RGZEESDX

Ball

1LA02132EE51

933

SA-7IEE

6.88

89.5

146

7.5

1800

213T

460

RGZEESDX

Ball

1LA02134EE41

906

SA-7IEE

9.5

91.7

205

7.5

1800

213T

575

RGZEESDX

Ball

1LA02134EE51

906

SA-7IEE

7.6

91.7

205

7.5

1200

254T

460

RGZEESDX

Ball

1LA02546EE41

1499

SA-7IEE

10.5

91

290

7.5

1200

254T

575

RGZEESDX

Ball

1LA02546EE51

1499

SA-7IEE

8.4

91

290

7.5

900

256T

460

RGZEESDX

Ball

1LA02568EE41

2540

SA-7IEE

7.5

900

256T

575

RGZEESDX

Ball

1LA02568EE51

2540

SA-7IEE

12 9.6

87.5

275

87.5

275

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD100 IEEE841.

3-26

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-27

NEMA PREMIUM Severe Duty

NEMA PREMIUM Severe Duty

Voltage

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

NEMA PREMIUM General Purpose

Specifications table begins on the next page

Frame

FL Amps

HIGH EFFICIENT P-Base Vertical

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is precision balanced to ISO G1.0 for extended bearing life, and includes a high-strength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

RPM

List Multiplier Price $ Symbol

HIGH EFFICIENT Definite Purpose

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for all frames.

Insulation – Proprietary inverter-rated Class F non-hygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. This insulation system meets or exceeds NEMA MG1-2003, Part 31, making all motors suitable for operation with variable frequency drives.

HP

DE Bearing

HIGH EFFICIENT Hazardous Duty

•1 to 400 HP •1.15 service factor, 40ºC ambient •3600, 1800, 1200 or 900 RPM •3 phase, 60 Hz; 460 volt; 575 volt available •Meets or exceeds IEEE 841-2001 standards •Meets or exceeds NEMA Premium™ efficiency standards •Class F insulation, Class B temperature rise •NEMA Design B, Continuous Duty •0.06 IPS vibration / 0.005” foot flatness •143T through S449 frame

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Hazardous Duty

RGZEESDX

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT Definite Purpose

RGZEESDX

HIGH EFFICIENT General Purpose

HIGH EFFICIENT P-Base Vertical

Severe Duty / IEEE 841 - TEFC Motors

Introduction

Severe Duty / IEEE 841 - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed

RPM

Frame

Type

Part Number

RGZEESDX

Ball

1LA02152EE41

Voltage

List Multiplier Price $ Symbol

FL Amps

FL Nom. Eff. (%)

Weight (lbs.)

11.4

90.2

164

Stock Model

Horizontal, Foot Mounted - continued 10

3600

215T

460

1072

SA-7IEE

10

3600

215T

575

RGZEESDX

Ball

1LA02152EE51

1072

SA-7IEE

9.12

90.2

164

10

1800

215T

460

RGZEESDX

Ball

1LA02154EE41

1085

SA-7IEE

12.5

91.7

222

10

1800

215T

575

RGZEESDX

Ball

1LA02154EE51

1085

SA-7IEE

10

91.7

222

10

1200

256T

460

RGZEESDX

Ball

1LA02566EE41

-1865

SA-7IEE

13.8

91

310

10

1200

256T

575

RGZEESDX

Ball

1LA02566EE51

1865

SA-7IEE

11.04

91

310

10

900

284T

460

RGZEESDX

Ball

1LA02848EE41

3018

SA-7IEE

15

90.2

362

10

900

284T

575

RGZEESDX

Ball

1LA02848EE51

3018

SA-7IEE

12

90.2

362

15

3600

254T

460

RGZEESDX

Ball

1LA02542EE41

1455

SA-7IEE

17

91

251

15

3600

254T

575

RGZEESDX

Ball

1LA02542EE51

1455

SA-7IEE

13.6

91

251

15

1800

254T

460

RGZEESDX

Ball

1LA02544EE41

1429

SA-7IEE

19

92.4

315

15

1800

254T

575

RGZEESDX

Ball

1LA02544EE51

1429

SA-7IEE

15.2

92.4

315

15

1200

284T

460

RGZEESDX

Ball

1LA02846EE41

2431

SA-7IEE

21

91.7

400

15

1200

284T

575

RGZEESDX

Ball

1LA02846EE51

2431

SA-7IEE

16.8

91.7

400

15

900

286T

460

RGZEESDX

Ball

1LA02868EE41

3860

SA-7IEE

23

90.2

420

15

900

286T

575

RGZEESDX

Ball

1LA02868EE51

3860

SA-7IEE

18.4

90.2

420

20

3600

256T

460

RGZEESDX

Ball

1LA02562EE41

1786

SA-7IEE

23

91

275

20

3600

256T

575

RGZEESDX

Ball

1LA02562EE51

1786

SA-7IEE

18.4

91

275

20

1800

256T

460

RGZEESDX

Ball

1LA02564EE41

1842

SA-7IEE

24

93

340

1800

256T

575

RGZEESDX

Ball

1LA02564EE51

1842

SA-7IEE

19.2

93

340

1200

286T

460

RGZEESDX

Ball

1LA02866EE41

2963

SA-7IEE

27

91.7

465

20

1200

286T

575

RGZEESDX

Ball

1LA02866EE51

2963

SA-7IEE

21.6

91.7

465

20

900

324T

460

RGZEESDX

Ball

1LA03248EE41

4719

SA-7IEE

31

91

570

20

900

324T

575

RGZEESDX

Ball

1LA03248EE51

4719

SA-7IEE

24.8

91

570

25

3600

284TS

460

RGZEESDX

Ball

1LA02842EE42

2220

SA-7IEE

29

91.7

415

25

3600

284TS

575

RGZEESDX

Ball

1LA02842EE52

2220

SA-7IEE

23.2

91.7

415

25

1800

284T

460

RGZEESDX

Ball

1LA02844EE41

2120

SA-7IEE

30

93.6

445

25

1800

284T

575

RGZEESDX

Ball

1LA02844EE51

2120

SA-7IEE

24

93.6

445

25

1800

284TS

460

RGZEESDX

Ball

1LA02844EE42

2120

SA-7IEE

30

93.6

445

1800

284TS

575

RGZEESDX

Ball

1LA02844EE52

2120

SA-7IEE

24

93.6

445

1200

324T

460

RGZEESDX

Ball

1LA03246EE41

3591

SA-7IEE

33

93

640

25

1200

324T

575

RGZEESDX

Ball

1LA03246EE51

3591

SA-7IEE

26.4

93

640

25

900

326T

460

RGZEESDX

Ball

1LA03268EE41

5487

SA-7IEE

41

90.2

582

25

900

326T

575

RGZEESDX

Ball

1LA03268EE51

5487

SA-7IEE

32.8

90.2

582

30

3600

286TS

460

RGZEESDX

Ball

1LA02862EE42

2593

SA-7IEE

34

91.7

430

3600

286TS

575

RGZEESDX

Ball

1LA02862EE52

2593

SA-7IEE

27.2

91.7

430

1800

286T

460

RGZEESDX

Ball

1LA02864EE41

2465

SA-7IEE

35

93.6

465

30

1800

286T

575

RGZEESDX

Ball

1LA02864EE51

2465

SA-7IEE

28

93.6

465

30

1800

286TS

460

RGZEESDX

Ball

1LA02864EE42

2465

SA-7IEE

35

93.6

465

30

1800

286TS

575

RGZEESDX

Ball

1LA02864EE52

2465

SA-7IEE

28

93.6

465

30

1200

326T

460

RGZEESDX

Ball

1LA03266EE41

4137

SA-7IEE

39

93

675

30

1200

326T

575

RGZEESDX

Ball

1LA03266EE51

4137

SA-7IEE

31.2

93

675

30

900

364T

460

RGZEESDX

Ball

1LA03648EE41

6494

SA-7IEE

47

91.7

740

30

900

364T

575

RGZEESDX

Ball

1LA03648EE51

6494

SA-7IEE

37.6

91.7

740

40

3600

324TS

460

RGZEESDX

Ball

1LA03242EE42

3420

SA-7IEE

45

93.6

575

40

3600

324TS

575

RGZEESDX

Ball

1LA03242EE52

3420

SA-7IEE

36

93.6

575

✔

40

1800

324T

460

RGZEESDX

Ball

1LA03244EE41

3275

SA-7IEE

46

94.1

666

40

1800

324T

575

RGZEESDX

Ball

1LA03244EE51

3275

SA-7IEE

36.8

94.1

666

✔

40

1800

324TS

460

RGZEESDX

Ball

1LA03244EE42

3275

SA-7IEE

46

94.1

666

40

1800

324TS

575

RGZEESDX

Ball

1LA03244EE52

3275

SA-7IEE

36.8

94.1

666

✔

40

1200

364T

460

RGZEESDX

Ball

1LA03646EE41

5606

SA-7IEE

49

94.1

863

40

1200

364T

575

RGZEESDX

Ball

1LA03646EE51

5606

SA-7IEE

39.2

94.1

863

✔

40

900

365T

460

RGZEESDX

Ball

1LA03658EE41

7852

SA-7IEE

63

91.7

840

40

900

365T

575

RGZEESDX

Ball

1LA03658EE51

7852

SA-7IEE

50.4

91.7

840

50

3600

326TS

460

RGZEESDX

Ball

1LA03262EE42

4348

SA-7IEE

55

93.6

610

50

3600

326TS

575

RGZEESDX

Ball

1LA03262EE52

4348

SA-7IEE

44

93.6

610

50

1800

326T

460

RGZEESDX

Ball

1LA03264EE41

3987

SA-7IEE

58

94.5

700

50

1800

326T

575

RGZEESDX

Ball

1LA03264EE51

3987

SA-7IEE

46.4

94.5

700

50

1800

326TS

460

RGZEESDX

Ball

1LA03264EE42

3987

SA-7IEE

58

94.5

700

50

1800

326TS

575

RGZEESDX

Ball

1LA03264EE52

3987

SA-7IEE

46.4

94.5

700

50

1200

365T

460

RGZEESDX

Ball

1LA03656EE41

6381

SA-7IEE

62

94.1

900

50

1200

365T

575

RGZEESDX

Ball

1LA03656EE51

6381

SA-7IEE

49.6

94.1

900

50

900

404T

460

RGZEESDX

Ball

1LA04048EE41

9139

SA-7IEE

67

92.4

1116

50

900

404T

575

RGZEESDX

Ball

1LA04048EE51

9139

SA-7IEE

53.6

92.4

1116

60

3600

364TS

460

RGZEESDX

Ball

1LA03642EE42

5770

SA-7IEE

68

93.6

717

60

3600

364TS

575

RGZEESDX

Ball

1LA03642EE52

5770

SA-7IEE

54.4

93.6

717

60

1800

364T

460

RGZEESDX

Ball

1LA03644EE41

5670

SA-7IEE

68

95

930

60

1800

364T

575

RGZEESDX

Ball

1LA03644EE51

5670

SA-7IEE

54.4

95

930

60

1800

364TS

460

RGZEESDX

Ball

1LA03644EE42

5670

SA-7IEE

68

95

930

60

1800

364TS

575

RGZEESDX

Ball

1LA03644EE52

5670

SA-7IEE

54.4

95

930

60

1200

404T

460

RGZEESDX

Ball

1LA04046EE41

7282

SA-7IEE

74

94.5

1100

60

1200

404T

575

RGZEESDX

Ball

1LA04046EE51

7282

SA-7IEE

59.2

94.5

1100

60

900

405T

460

RGZEESDX

Ball

1LA04058EE41

10255

SA-7IEE

78

92.4

1182

60

900

405T

575

RGZEESDX

Ball

1LA04058EE51

10255

SA-7IEE

62.4

92.4

1182

75

3600

365TS

460

RGZEESDX

Ball

1LA03652EE42

7245

SA-7IEE

85

94.1

815

75

3600

365TS

575

RGZEESDX

Ball

1LA03652EE52

7245

SA-7IEE

68

94.1

815

75

1800

365T

460

RGZEESDX

Ball

1LA03654EE41

7062

SA-7IEE

85

95.4

1000

75

1800

365T

575

RGZEESDX

Ball

1LA03654EE51

7062

SA-7IEE

68

95.4

1000

75

1800

365TS

460

RGZEESDX

Ball

1LA03654EE42

7062

SA-7IEE

85

95.4

1000

75

1800

365TS

575

RGZEESDX

Ball

1LA03654EE52

7062

SA-7IEE

68

95.4

1000

75

1200

405T

460

RGZEESDX

Ball

1LA04056EE41

8497

SA-7IEE

93

94.5

1150

75

1200

405T

575

RGZEESDX

Ball

1LA04056EE51

8497

SA-7IEE

74.4

94.5

1150

75

900

444T

460

RGZEESDX

Roller

1LA04448EE41

13636

SA-7IEE

94

93.6

1525

75

900

444T

575

RGZEESDX

Roller

1LA04448EE51

13636

SA-7IEE

75.2

93.6

1525

100

3600

405TS

460

RGZEESDX

Ball

1LA04052EE42

9624

SA-7IEE

94.1

1100

100

3600

405TS

575

RGZEESDX

Ball

1LA04052EE52

9624

SA-7IEE

94.1

1100

100

1800

405T

460

RGZEESDX

Ball

1LA04054EE41

8725

SA-7IEE

95.4

1160

100

1800

405T

575

RGZEESDX

Ball

1LA04054EE51

8725

SA-7IEE

95.4

1160

100

1800

405TS

460

RGZEESDX

Ball

1LA04054EE42

8725

SA-7IEE

95.4

1160

100

1800

405TS

575

RGZEESDX

Ball

1LA04054EE52

8725

SA-7IEE

95.4

1160

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

NEMA PREMIUM Severe Duty

DOE#CC032A

DOE#CC032A

108 86.4 113 90.4 113 90.4

2007 Low Voltage AC Motors Selection and Pricing Guide

Stock Model ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

3-29

NEMA PREMIUM Severe Duty

2007 Low Voltage AC Motors Selection and Pricing Guide

Weight (lbs.)

✔

Shaded ratings will be discontinued when present stock is depleted. Replaced by type SD100 IEEE841

3-28

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

30 30

FL Amps

HIGH EFFICIENT P-Base Vertical

25 25

Part Number

List Multiplier Price $ Symbol

HIGH EFFICIENT Definite Purpose

20 20

HP RPM Frame Voltage Type Horizontal, Foot Mounted - continued

DE Bearing

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Hazardous Duty

HP

DE Bearing

Stock/Modifiable

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT Definite Purpose

RGZEESDX

Stock/Modifiable

HIGH EFFICIENT Severe Duty

HIGH EFFICIENT P-Base Vertical

RGZEESDX

HIGH EFFICIENT General Purpose

NEMA PREMIUM General Purpose

Severe Duty / IEEE 841 - TEFC Motors

Introduction

Severe Duty / IEEE 841 - TEFC Motors

Introduction HIGH EFFICIENT General Purpose HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty

RPM

Frame

Voltage

Type

Part Number

List Multiplier Price $ Symbol

FL Amps 117

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

95

1545

✔

95

1545

Horizontal, Foot Mounted - continued 100

1200

444T

460

RGZEESDX

Roller

1LA04446EE41

11717

SA-7IEE

100

1200

444T

575

RGZEESDX

Roller

1LA04446EE51

11717

SA-7IEE

100

1200

444TS

460

RGZEESDX

Ball

1LA04446EE42

11717

SA-7IEE

100

1200

444TS

575

RGZEESDX

Ball

1LA04446EE52

11717

SA-7IEE

100

1200

B444T

460

RGZEESDX

Ball

1LA04446EE4N

11717

SA-7IEE

100

1200

B444T

575

RGZEESDX

Ball

1LA04446EE5N

11717

SA-7IEE

100

900

445T

460

RGZEESDX

Roller

1LA04458EE41

16710

SA-7IEE

100

900

445T

575

RGZEESDX

Roller

1LA04458EE51

16710

SA-7IEE

125

3600

444TS

460

RGZEESDX

Ball

1LA04442EE42

12360

SA-7IEE

125

3600

444TS

575

RGZEESDX

Ball

1LA04442EE52

12360

SA-7IEE

93.6 117

95

1545

95

1545

95

1545

95

1545

94.1

1697

94.1

1697

138

95

1454

110.4

95

1454

93.6 117 93.6 123 98.4

125

1800

444T

460

RGZEESDX

Roller

1LA04444EE41

11383

SA-7IEE

143

95.4

1600

125

1800

444T

575

RGZEESDX

Roller

1LA04444EE51

11383

SA-7IEE

114.4

95.4

1600

125

1800

444TS

460

RGZEESDX

Ball

1LA04444EE42

11383

SA-7IEE

143

95.4

1600

125

1800

444TS

575

RGZEESDX

Ball

1LA04444EE52

11383

SA-7IEE

114.4

95.4

1600

125

1800

B444T

460

RGZEESDX

Ball

1LA04444EE4N

11383

SA-7IEE

143

95.4

1600

125

1800

B444T

575

RGZEESDX

Ball

1LA04444EE5N

11383

SA-7IEE

114.4

95.4

1600

125

1200

445T

460

RGZEESDX

Roller

1LA04456EE41

14135

SA-7IEE

144

95

1720

125

1200

445T

575

RGZEESDX

Roller

1LA04456EE51

14135

SA-7IEE

115.2

95

1720

125

1200

445TS

460

RGZEESDX

Ball

1LA04456EE42

14135

SA-7IEE

144

95

1720

125

1200

445TS

575

RGZEESDX

Ball

1LA04456EE52

14135

SA-7IEE

115.2

95

1720

125

1200

B445T

460

RGZEESDX

Ball

1LA04456EE4N

14135

SA-7IEE

144

95

1720

125

1200

B445T

575

RGZEESDX

Ball

1LA04456EE5N

14135

SA-7IEE

115.2

95

1720

125

900

447T

460

RGZEESDX

Roller

1LA04478EE41

17163

SA-7IEE

152

94.1

2018

125

900

447T

575

RGZEESDX

Roller

1LA04478EE51

17163

SA-7IEE

121.6

94.1

2018

150

3600

445TS

460

RGZEESDX

Ball

1LA04452EE42

14450

SA-7IEE

164

95

1615

445TS

575

RGZEESDX

Ball

1LA04452EE52

14450

SA-7IEE

131.2

95

1615

1800

445T

460

RGZEESDX

Roller

1LA04454EE41

12875

SA-7IEE

170

95.8

1710

150

1800

445T

575

RGZEESDX

Roller

1LA04454EE51

12875

SA-7IEE

136

95.8

1710

150

1800

445TS

460

RGZEESDX

Ball

1LA04454EE42

12875

SA-7IEE

170

95.8

1710

150

1800

445TS

575

RGZEESDX

Ball

1LA04454EE52

12875

SA-7IEE

136

95.8

1710

150

1800

B445T

460

RGZEESDX

Ball

1LA04454EE4N

12875

SA-7IEE

170

95.8

1710

150

1800

B445T

575

RGZEESDX

Ball

1LA04454EE5N

12875

SA-7IEE

136

95.8

1710

150

1200

447T

460

RGZEESDX

Roller

1LA04476EE41

15527

SA-7IEE

172

95.8

1995

150

1200

447T

575

RGZEESDX

Roller

1LA04476EE51

15527

SA-7IEE

137.6

95.8

1995

150

1200

447TS

460

RGZEESDX

Ball

1LA04476EE42

15527

SA-7IEE

172

95.8

1995

150

1200

447TS

575

RGZEESDX

Ball

1LA04476EE52

15527

SA-7IEE

137.6

95.8

1995

1200

B447T

460

RGZEESDX

Ball

1LA04476EE4N

15527

SA-7IEE

172

95.8

1995

150

1200

B447T

575

RGZEESDX

Ball

1LA04476EE5N

15527

SA-7IEE

137.6

95.8

1995

150

900

449T

460

RGZEESDX

Roller

1LA04498EE41

21945

SA-7IEE

180

94.1

2480

150

900

449T

575

RGZEESDX

Roller

1LA04498EE51

21945

SA-7IEE

144

94.1

2480

200

3600

447TS

460

RGZEESDX

Ball

1LA04472EE42

18122

SA-7IEE

216

95.4

1890

200

3600

447TS

575

RGZEESDX

Ball

1LA04472EE52

18122

SA-7IEE

172.8

95.4

1890

200

1800

447T

460

RGZEESDX

Roller

1LA04474EE41

15660

SA-7IEE

226

96.2

2035

200

1800

447T

575

RGZEESDX

Roller

1LA04474EE51

15660

SA-7IEE

180.8

96.2

2035

200

1800

447TS

460

RGZEESDX

Ball

1LA04474EE42

15660

SA-7IEE

226

96.2

2035

1800

447TS

575

RGZEESDX

Ball

1LA04474EE52

15660

SA-7IEE

180.8

96.2

2035

200

1800

B447T

460

RGZEESDX

Ball

1LA04474EE4N

15660

SA-7IEE

226

96.2

2035

200

1800

B447T

575

RGZEESDX

Ball

1LA04474EE5N

15660

SA-7IEE

180.8

96.2

2035

3-30

2007 Low Voltage AC Motors Selection and Pricing Guide

Weight (lbs.)

Stock Model ✔

200

1200

449T

460

RGZEESDX Roller

1LA04496EE41

18832

SA-7IEE

227

95.8

2425

200

1200

449T

575

RGZEESDX Roller

1LA04496EE51

18832

SA-7IEE

181.6

95.8

2425

200

1200

449TS

460

RGZEESDX Ball

1LA04496EE42

18832

SA-7IEE

227

95.8

2425 2425

200

1200

449TS

575

RGZEESDX Ball

1LA04496EE52

18832

SA-7IEE

181.6

95.8

200

1200

B449T

460

RGZEESDX Ball

1LA04496EE4N

18832

SA-7IEE

227

95.8

2425

200

1200

B449T

575

RGZEESDX Ball

1LA04496EE5N

18832

SA-7IEE

181.6

95.8

2425

200

900

S449LS

460

RGZEESDX Roller

1LA02008EG41

31275

SA-7IEE

240

94.5

3200 3200

✔

200

900

S449LS

575

RGZEESDX Roller

1LA02008EG51

31275

SA-7IEE

192

94.5

250

3600

449TS

460

RGZEESDX Ball

1LA04492EE42

22840

SA-7IEE

269

95.8

2272

✔

250

3600

449TS

575

RGZEESDX Ball

1LA04492EE52

22840

SA-7IEE

215.2

95.8

2272

250

1800

449T

460

RGZEESDX Roller

1LA04494EE41

19650

SA-7IEE

281

96.2

2425

250

1800

449T

575

RGZEESDX Roller

1LA04494EE51

19650

SA-7IEE

224.8

96.2

2425

250

1800

449TS

460

RGZEESDX Ball

1LA04494EE42

19650

SA-7IEE

281

96.2

2425

250

1800

449TS

575

RGZEESDX Ball

1LA04494EE52

19650

SA-7IEE

224.8

96.2

2425

250

1800

B449T

460

RGZEESDX Ball

1LA04494EE4N

19650

SA-7IEE

281

96.2

2425

250

1800

B449T

575

RGZEESDX Ball

1LA04494EE5N

19650

SA-7IEE

224.8

96.2

2425

250

1200

449T

460

RGZEESDX Roller

1LA04496EH41

20490

SA-7IEE

281

95.8

2390

250

1200

449T

575

RGZEESDX Roller

1LA04496EH51

20490

SA-7IEE

224.8

95.8

2390

250

1200

449TS

460

RGZEESDX Ball

1LA04496EH42

20490

SA-7IEE

281

95.8

2390 2390

✔ ✔ ✔ ✔ ✔

250

1200

449TS

575

RGZEESDX Ball

1LA04496EH52

20490

SA-7IEE

224.8

95.8

250

1200

B449T

460

RGZEESDX Ball

1LA04496EH4N

20490

SA-7IEE

281

95.8

2390

250

1200

B449T

575

RGZEESDX Ball

1LA04496EH5N

20490

SA-7IEE

224.8

95.8

2390

250

900

S449LS

460

RGZEESDX Roller

1LA02508EG41

33925

SA-7IEE

303

94.5

3220

250

900

S449LS

575

RGZEESDX Roller

1LA02508EG51

33925

SA-7IEE

242.4

94.5

3220

300

3600

449TS

460

RGZEESDX Ball

1LA04492EH42

30830

SA-7IEE

323

95.8

2200

300

3600

449TS

575

RGZEESDX Ball

1LA04492EH52

30830

SA-7IEE

258.4

95.8

2200

300

1800

S449LS

460

1LA03004EG41

28330

SA-7IEE

346

96.2

3130

300

1800

S449LS

575

RGZEESDX Roller 1 RGZEESDX Roller 1

1LA03004EG51

28330

SA-7IEE

276.8

96.2

3130

300

1800

S449SS

460

1LA03004EG42

28330

SA-7IEE

346

96.2

3130

300

1800

S449SS

575

RGZEESDX Ball 1 RGZEESDX Ball 1

1LA03004EG52

28330

SA-7IEE

276.8

96.2

3130

300

1200

S449LS

460

RGZEESDX Roller

1LA03006EG41

37850

SA-7IEE

342

95.8

3240

✔

300

1200

S449LS

575

37850

SA-7IEE

273.6

95.8

3240

3600

S449SS

460

RGZEESDX Roller RGZEESDX Ball 1

1LA03006EG51

350

1LA03502EG42

35040

SA-7IEE

372

95.8

2890

✔

350

3600

S449SS

575

RGZEESDX Ball 1

1LA03502EG52

35040

SA-7IEE

297.6

95.8

2890

350

1800

S449LS

460

1LA03504EG41

32450

SA-7IEE

392

96.2

3190

350

1800

S449LS

575

RGZEESDX Roller 1 RGZEESDX Roller 1

1LA03504EG51

32450

SA-7IEE

313.6

96.2

3190

350

1800

S449SS

460

1LA03504EG42

32450

SA-7IEE

392

96.2

3190

350

1800

S449SS

575

RGZEESDX Ball 1 RGZEESDX Ball 1

1LA03504EG52

32450

SA-7IEE

313.6

96.2

3190

400

3600

S449SS

460

1LA04002EG42

39300

SA-7IEE

422

95.8

3065

400

3600

S449SS

575

RGZEESDX Ball 1 RGZEESDX Ball 1

1LA04002EG52

39300

SA-7IEE

337.6

95.8

3065

400

1800

S449LS

460

1LA04004EG41

36400

SA-7IEE

454

96.2

3240

400

1800

S449LS

575

RGZEESDX Roller 1 RGZEESDX Roller 1

1LA04004EG51

36400

SA-7IEE

363.2

96.2

3240

400

1800

S449SS

460

1LA04004EG42

36400

SA-7IEE

454

96.2

3240

400

1800

S449SS

575

RGZEESDX Ball 1 RGZEESDX Ball 1

1LA04004EG52

36400

SA-7IEE

363.2

96.2

3240

✔ ✔ ✔ ✔ ✔ ✔

✔ ✔ ✔ ✔ ✔

DOE#CC032A

✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

1 CW rotation facing opposite drive end.

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

3-31

NEMA PREMIUM Severe Duty

200

FL Nom. Eff. (%)

NEMA PREMIUM General Purpose

150

✔

FL Amps

HIGH EFFICIENT P-Base Vertical

3600

150

✔

Part Number

List Multiplier Price $ Symbol

HIGH EFFICIENT Definite Purpose

150

✔

HP RPM Frame Voltage Type Horizontal, Foot Mounted - continued

DE Bearing

HIGH EFFICIENT Hazardous Duty

HIGH EFFICIENT Definite Purpose

HP

DE Bearing

HIGH EFFICIENT Multi Speed

HIGH EFFICIENT P-Base Vertical

RGZEESDX

Stock/Modifiable

HIGH EFFICIENT Severe Duty

NEMA PREMIUM General Purpose

RGZEESDX

HIGH EFFICIENT General Purpose

NEMA PREMIUM Severe Duty

Severe Duty / IEEE 841 - TEFC Motors

Introduction

Severe Duty / IEEE 841 - TEFC Motors

HIGH EFFICIENT Severe Duty HIGH EFFICIENT Multi Speed HIGH EFFICIENT Hazardous Duty NEMA PREMIUM General Purpose

HIGH EFFICIENT P-Base Vertical

Dimensions

NEMA PREMIUM Severe Duty

Typical Performance

HIGH EFFICIENT Definite Purpose

Caution must be observed when applying standard motors for continuous low speed, constant torque operation. A standard motor’s self-cooling capacity depends upon self-ventilation schemes that are greatly reduced at decreased operating speeds.

Modifications Accessories

Anytime encoders, insulated bearings, shaft grounding, blower cooling, or NEMA part 31 is required, use RGZESDI.

Variable Torque Applications From the perspective of motor cooling, AC motors are well suited to be used in adjustable speed variable torque applications, such as centrifugal fans or pumps. The torque characteristics of a variable torque load is such that the load falls off rapidly as the motor speed is reduced. The variable torque load eliminates the necessity to de-rate the motor due to excessive heat resulting from diminished motor cooling at reduced speeds. Variable Torque operation beyond base speed must be reviewed by Siemens.

Constant Torque Operation Many general industrial machines, other than fans and pumps, are constant torque systems where the machine’s torque requirement is independent of its speed. If the machine speed is doubled, its horsepower requirement doubles. Vector drives can supply nearly ideal conditions to the motor, resulting in better motor performance, cooler operation, and more precise speed regulation, especially at low speed ranges. A standard 4-pole 460V motor can be accurately controlled by this method to its synchronous speed of 1800 RPM. RGZESDI Constant Torque motors provide full rated torque within their listed speed range, without exceeding their Class F temperature rating on PWM (pulse width modulated) inverter power. Ratings in this catalog are based on use with vector type IGBT inverters, set at a minimum 3 kHz switching frequency, and are designed for operation at 150% of rated torque for one minute, up to the base speed of the motor (overload capacity declines as the motor reaches maximum speed).

Lead Time

WHEN TO USE RGZESDI

APPLICATION CONSIDERATIONS

INVERTER Duty Hazardous Duty

As a manufacturer of both variable speed drives and AC motors, Siemens has a superior understanding of their collective operation, application, and performance. The Inverter Duty Motors outlined in this publication are the result of an extensive testing program to establish guidelines for their typical utilization. Siemens totally enclosed RGZESDI inverter-duty motors are rated for continuous operation in a 40°C ambient at altitudes up to 3300 feet above sea level. For specialized applications, such as non-standard ambient, intermittent or high duty cycles, high constant horsepower speed ranges, or other special conditions, please consult Siemens.

HIGH EFFICIENT General Purpose

Introduction

General Information

INVERTER Duty Severe Duty

Notes

3-32

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

4-1

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time Modifications Accessories

3600 RPM

1800 RPM

1200 RPM

143-184 213-256 284-286 324-326 364-365 404-405 444-445* 447-449*

5400 5400 5400 4500 3600 3600 3600 3600

3600 3600 2700 2700 2700 2700 2700 2250

2400 2400 2080 1960 1900 1840 1800 1800

CAUTION It is the responsibility of the startup personnel during commissioning of the VFD/motor combination to properly tune the drive to the motor for the specific application. Application of motors which are not per the guidelines of this document may void the warranty, if they are not specifically approved by Siemens.

Motor Frame 143-184 213-256 284-286 324-326 364-365 404-445 447-449

3600 RPM 7200 5400 5400 4500 4500 3600 3600

1800 RPM 5400 4200 3600 3600 2700 2700 2250

1200 RPM 2700 2700 2700 2700 2700 1800 1800

OPTIONS Blowers Low rotational speeds at constant torque loads, common in many vector applications, provide the motor with reduced ventilation. As a result, these motors are designed as Totally Enclosed Blower Cooled. Blowers are powered by a Siemens 1 HP(250-360FR) or 2 HP (400-S449FR), TENV Severe Duty, 3 phase motor. Standard voltages is 230/460 volts, 3 phase, 60 hertz. Brakes Brake motors available as custom build only. Encoders These electronic devices sense rotor speed and direction. A cable is connected from the encoder to the VFD. Various resolutions (PPR, pulses per revolution) are available. All encoders offer quadrature (direction sensing), with line driver output. Service Factor Standard service factor for RGZESDI motors is 1.0 on inverter power. RGZESDI motors are suitable for 1.15 service factor on sine wave power. Thermal Protection All RGZESDI and RGZZESDI motors are equipped with Class F normally closed

INSULATION Type RGZESDI inverter duty motors utilize an insulation system designed to meet the requirements of NEMA MG1 Part 31 and rated Class F temperature.

Inverter Duty High Efficiency Severe Duty TEFC motors are ideal for both variable torque and constant torque loads, designed for inverter or vector applications. These motors are well suited to be used in adjustable speed applications such as centrifugal fans, pumps, blowers, mixers, machine tools, chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical.

Performance Specifications •1 to 400 HP •Variable Torque – Zero to base speed •Constant Torque – 10:1, 6:1, 4:1 •1.15 service factor on sine wave power, 40ºC ambient •1.0 service factor on inverter power •3600, 1800, 1200 or 900 RPM •3 phase, 60 Hz, 460 volt; 200, 230 & 575 volt available •Meets or exceeds EPAct Efficiency standards •Class F insulation, Class B temperature rise •Continuous Duty •143T through S449 frame

Features for Long Life Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to S449. Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses. Insulation – Proprietary inverter-duty Class F non-hygroscopic (corona resistant) insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. All motors are equipped with two series connected, normally closed, Class F thermostats for detection of overload conditions and/or excessive heating. Suitable for operation from adjustable speed drives with an insulation system that meets or exceeds NEMA MG1-2003, Part 31. Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-S449 frames have a drive end shaft V-ring slinger.

Dimensions

*444T-449T frame motors intended for belt duty are supplied with roller bearings.

(does not imply constant horsepower capability)

thermostats for detection of overload conditions. Other devices are available as shown. Accessories, such as “C” face kits or encoders, can be added to stock motors in our Super Mod Center. Other common modifications, such as addition of space heaters, shaft seals or change to F2 assembly, are also available from the Super Mod Center. This facility provides a short lead time on many popular modifications. Voltage 575V available - contact Siemens 50Hz - De-rate as usual.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Specifications table begins on the next page

4-2

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

Typical Performance

Motor Frame

Maximum Safe Mechanical Speed Limits Direct Connected Loads

Modifications Accessories

Constant Horsepower Operation AC motor controllers are also adaptable to constant horsepower operation. With this mode of operation, the volts/HZ ratio is maintained to a specific frequency, normally 60 Hz. At this point, the voltage is “clamped” at a constant level while the frequency is adjusted further to achieve the desired maximum speed. The motor becomes “voltage starved” above the clamping point and torque decreases as speed increases, resulting in constant horsepower output. In constant horsepower applications, the drive provides conventional constant torque/variable horsepower operation up to 60 hertz. Above 60 hertz, the motor/drive provides constant horsepower, variable torque operation. Constant Horsepower Speed Limits

RGZESDI - Variable Torque/Constant Torque

Lead Time

Typical Performance

General Information

INVERTER Duty Hazardous Duty

Dimensions

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

4-3

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Weight (lbs.)

Stock Model

HP

RPM Frame Voltage

✔

10

3600

215T

460

RGZESDI

Ball

10

3600

215T

575

RGZESDI

Ball

Part Number

10:1

1LA01444VT41

775

SA-7INV

1.5

82.5

45

10:1

1LA01444VT51

775

SA-7INV

1.5

82.5

45

Ball

10:1

1LA01456VT41

855

SA-7INV

1.8

80

55

✔

10

1800

215T

460

RGZESDI

Ball

10:1

1LA01456VT51

855

SA-7INV

1.8

80

55

✔

10

1800

215T

575

RGZESDI

Ball

10:1

1180

SA-7INV

1.9

78.5

85

10

1200

256T

460

RPM Frame Voltage

1

1800

143T

460

RGZESDI

Ball

1

1800

143T

575

RGZESDI

Ball

1

1200

145T

460

RGZESDI

1

1200

145T

575

RGZESDI

1

900

182T

460

RGZESDI

CT DE Speed Bearing Range

Stock/Modifiable Weight (lbs.)

Stock Model ✔

Part Number

10:1

1LA02152VT41

1595

SA-7INV

12

89.5

160

10:1

1LA02152VT51

1595

SA-7INV

12

89.5

160

Ball

10:1

1LA02154VT41

1455

SA-7INV

13

89.5

160

Ball

10:1

1LA02154VT51

1455

SA-7INV

13

89.5

160

RGZESDI

Ball

6:1

1LA02566VT41

2055

SA-7INV

13

90.2

285

✔

1LA02566VT51

2055

SA-7INV

13

90.2

285

✔

2990

SA-7INV

15

91

336

Type

FL Mult. Sym. Amps

FL Nom. Eff. (%)

List Price $

1

900

182T

575

RGZESDI

Ball

10:1

1180

SA-7INV

1.9

78.5

85

10

1200

256T

575

RGZESDI

Ball

6:1

1.5

3600

143T

460

RGZESDI

Ball

10:1

1LA01442VT41

875

SA-7INV

2

82.5

45

✔

10

900

284T

460

RGZESDI

Ball

6:1

1.5

3600

143T

575

RGZESDI

Ball

10:1

1LA01442VT51

875

SA-7INV

2

82.5

45

✔

10

900

284T

575

RGZESDI

Ball

6:1

2990

SA-7INV

15

91

336

1.5

1800

145T

460

RGZESDI

Ball

10:1

1LA01454VT41

805

SA-7INV

2.2

84

55

✔

15

3600

254T

460

RGZESDI

Ball

6:1

1LA02542VT41

1840

SA-7INV

17

90.2

245

1.5

1800

145T

575

RGZESDI

Ball

10:1

1LA01454VT51

805

SA-7INV

2.2

84

55

15

3600

254T

575

RGZESDI

Ball

6:1

1LA02542VT51

1840

SA-7INV

17

90.2

245

1.5

1200

182T

460

RGZESDI

Ball

10:1

1LA01826VT41

1005

SA-7INV

2.3

85.5

85

15

1800

254T

460

RGZESDI

Ball

6:1

1LA02544VT41

1750

SA-7INV

19

91.7

245

1.5

1200

182T

575

RGZESDI

Ball

10:1

1LA01826VT51

1005

SA-7INV

2.3

85.5

85

15

1800

254T

575

RGZESDI

Ball

6:1

1LA02544VT51

1750

SA-7INV

19

91.7

245

✔

✔

✔ ✔ ✔

1.5

900

184T

460

RGZESDI

Ball

10:1

1385

SA-7INV

2.6

80

100

15

1200

284T

460

RGZESDI

Ball

6:1

1LA02846VT41

2675

SA-7INV

20

91

375

1.5

900

184T

575

RGZESDI

Ball

10:1

1385

SA-7INV

2.6

80

100

15

1200

284T

575

RGZESDI

Ball

6:1

1LA02846VT51

2675

SA-7INV

20

91

375

2

3600

145T

460

RGZESDI

Ball

10:1

1LA01452VT41

910

SA-7INV

2.5

84

55

15

900

286T

460

RGZESDI

Ball

6:1

3240

SA-7INV

23

91

430

2

3600

145T

575

RGZESDI

Ball

10:1

1LA01452VT51

910

SA-7INV

2.5

84

55

15

900

286T

575

RGZESDI

Ball

6:1

3240

SA-7INV

23

91

430

2

1800

145T

460

RGZESDI

Ball

10:1

1LA01464VT41

840

SA-7INV

2.9

84

62

✔

20

3600

256T

460

RGZESDI

Ball

6:1

1LA02562VT41

2191

SA-7INV

23

90.2

285

2

1800

145T

575

RGZESDI

Ball

10:1

1LA01464VT51

840

SA-7INV

2.9

84

55

✔

20

3600

256T

575

RGZESDI

Ball

6:1

1LA02562VT51

2191

SA-7INV

23

90.2

285

2

1200

184T

460

RGZESDI

Ball

10:1

1LA01846VT41

1075

SA-7INV

3

86.5

100

✔

20

1800

256T

460

RGZESDI

Ball

6:1

1LA02564VT41

2105

SA-7INV

26

91.7

285

2

1200

184T

575

RGZESDI

Ball

10:1

1LA01846VT51

1075

SA-7INV

3

86.5

100

✔

20

1800

256T

575

RGZESDI

Ball

6:1

1LA02564VT51

2105

SA-7INV

26

91.7

285

2

900

213T

460

RGZESDI

Ball

10:1

1540

SA-7INV

3.3

82.5

130

20

1200

286T

460

RGZESDI

Ball

6:1

1LA02866VT41

3146

SA-7INV

26

91.7

430

✔

2

900

213T

575

RGZESDI

Ball

10:1

1540

SA-7INV

3.3

82.5

130

20

1200

286T

575

RGZESDI

Ball

6:1

1LA02866VT51

3146

SA-7INV

26

91.7

430

✔

3

3600

182T

460

RGZESDI

Ball

10:1

1LA01822VT41

1070

SA-7INV

3.6

86.5

85

20

900

324T

460

RGZESDI

Ball

4:1

3958

SA-7INV

31

91

565

3

3600

182T

575

RGZESDI

Ball

10:1

1LA01822VT51

1070

SA-7INV

3.6

86.5

85

3

1800

182T

460

RGZESDI

Ball

10:1

1LA01824VT41

985

SA-7INV

3.9

87.5

85

3

1800

182T

575

RGZESDI

Ball

10:1

1LA01824VT51

985

SA-7INV

3.9

87.5

85

3

1200

213T

460

RGZESDI

Ball

10:1

1LA02136VT41

1185

SA-7INV

4

87.5

135

3

1200

213T

575

RGZESDI

Ball

10:1

1LA02136VT51

1185

SA-7INV

4

87.5

130

✔

900

324T

575

RGZESDI

Ball

4:1

3958

SA-7INV

31

91

565

25

3600

284TS

460

RGZESDI

Ball

6:1

1LA02842VT42

2979

SA-7INV

29

91.7

375

25

3600

284TS

575

RGZESDI

Ball

6:1

1LA02842VT52

2979

SA-7INV

29

91.7

477

✔

25

1800

284T

460

RGZESDI

Ball

6:1

1LA02844VT41

2466

SA-7INV

29

93

477

✔

25

1800

284T

575

RGZESDI

Ball

6:1

1LA02844VT51

2466

SA-7INV

29

93

477

✔ ✔

3

900

215T

460

RGZESDI

Ball

10:1

1850

SA-7INV

4.7

84

162

25

1200

324T

460

RGZESDI

Ball

4:1

1LA03246VT41

3856

SA-7INV

33

92.4

565

✔

3

900

215T

575

RGZESDI

Ball

10:1

1850

SA-7INV

4.7

84

162

25

1200

324T

575

RGZESDI

Ball

4:1

1LA03246VT51

3856

SA-7INV

33

92.4

565

✔

5

3600

184T

460

RGZESDI

Ball

10:1

1LA01842VT41

1178

SA-7INV

5.8

87.5

100

25

900

326T

460

RGZESDI

Ball

4:1

4620

SA-7INV

38

90.2

669

5

3600

184T

575

RGZESDI

Ball

10:1

1LA01842VT51

1178

SA-7INV

5.8

87.5

100

5

1800

184T

460

RGZESDI

Ball

10:1

1LA01844VT41

1085

SA-7INV

6.5

87.5

100

5

1800

184T

575

RGZESDI

Ball

10:1

1LA01844VT51

1085

SA-7INV

6.5

87.5

100

5

1200

215T

460

RGZESDI

Ball

10:1

1LA02156VT41

1515

SA-7INV

6.8

88.5

160

5

1200

215T

575

RGZESDI

Ball

10:1

1LA02156VT51

1515

SA-7INV

6.8

88.5

160

✔

25

900

326T

575

RGZESDI

Ball

4:1

4620

SA-7INV

38

90.2

669

30

3600

286TS

460

RGZESDI

Ball

6:1

1LA02862VT42

3406

SA-7INV

34

91.7

520

30

3600

286TS

575

RGZESDI

Ball

6:1

1LA02862VT52

3406

SA-7INV

34

91.7

494

✔

30

1800

286T

460

RGZESDI

Ball

6:1

1LA02864VT41

3065

SA-7INV

35

93

494

✔

30

1800

286T

575

RGZESDI

Ball

6:1

1LA02864VT51

3065

SA-7INV

35

93

494

✔

✔ ✔

5

900

254T

460

RGZESDI

Ball

6:1

2217

SA-7INV

7.5

86.5

250

30

1200

326T

460

RGZESDI

Ball

4:1

1LA03266VT41

4355

SA-7INV

39

92.4

669

✔

5

900

254T

575

RGZESDI

Ball

6:1

2217

SA-7INV

7.5

86.5

250

30

1200

326T

575

RGZESDI

Ball

4:1

1LA03266VT51

4355

SA-7INV

39

92.4

669

✔

7.5

3600

213T

460

RGZESDI

Ball

10:1

1LA02132VT41

1395

SA-7INV

8.8

88.5

151

30

900

364T

460

RGZESDI

Ball

4:1

5488

SA-7INV

47

91

800

7.5

3600

213T

575

RGZESDI

Ball

10:1

1LA02132VT51

1395

SA-7INV

8.8

88.5

130

7.5

1800

213T

460

RGZESDI

Ball

10:1

1LA02134VT41

1275

SA-7INV

9.5

89.5

157

7.5

1800

213T

575

RGZESDI

Ball

10:1

1LA02134VT51

1275

SA-7INV

9.5

89.5

130

7.5

1200

254T

460

RGZESDI

Ball

6:1

1LA02546VT41

1775

SA-7INV

9.8

90.2

245

7.5

1200

254T

575

RGZESDI

Ball

6:1

1LA02546VT51

1775

SA-7INV

9.8

90.2

245

✔

30

900

364T

575

RGZESDI

Ball

4:1

5488

SA-7INV

47

91

800

40

3600

324TS

460

RGZESDI

Ball

6:1

1LA03242VT42

4010

SA-7INV

45

93.6

565

✔

40

3600

324TS

575

RGZESDI

Ball

6:1

1LA03242VT52

4010

SA-7INV

45

93.6

565

✔

✔

40

1800

324T

460

RGZESDI

Ball

4:1

1LA03244VT41

3480

SA-7INV

47

93.6

565

✔

✔

40

1800

324T

575

RGZESDI

Ball

4:1

1LA03244VT51

3480

SA-7INV

47

93.6

565

✔

7.5

900

256T

460

RGZESDI

Ball

6:1

2540

SA-7INV

12

87.5

300

40

1200

364T

460

RGZESDI

Ball

4:1

1LA03646VT41

5675

SA-7INV

52

93.6

800

✔

7.5

900

256T

575

RGZESDI

Ball

6:1

2540

SA-7INV

12

87.5

300

40

1200

364T

575

RGZESDI

Ball

4:1

1LA03646VT51

5675

SA-7INV

52

93.6

800

✔

40

900

365T

460

RGZESDI

Ball

4:1

7978

SA-7INV

63

91.7

875

40

900

365T

575

RGZESDI

Ball

4:1

7978

SA-7INV

63

91.7

875

4-4

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

4-5

Dimensions

20 ✔

✔ Typical Performance

✔

✔

Modifications Accessories

Modifications Accessories

FL Nom. Eff. (%)

List Price $

HP

FL Mult. Sym. Amps

RGZESDI - Variable Torque/Constant Torque

Lead Time

Typical Performance

Type

CT DE Speed Bearing Range

Stock/Modifiable

INVERTER Duty Hazardous Duty

Dimensions

RGZESDI - Variable Torque/Constant Torque

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model

HP

RPM Frame Voltage

✔

200

3600

447TS

460

RGZESDI

Ball

4:1

1LA04472VT42 18470

SA-7INV

216

95

2280

200

3600

447TS

575

RGZESDI

Ball

4:1

1LA04472VT52 18470

SA-7INV

216

95

2280

200

1800

447TS

460

RGZESDI

Ball

4:1

1LA04474VT42 16088

SA-7INV

225

95.8

2280

200

1800

447TS

575

RGZESDI

Ball

4:1

1LA04474VT52 16088

SA-7INV

225

95.8

2280

200

1200

449TS

460

RGZESDI

Ball

4:1

1LA04496VT42 19280

SA-7INV

226

95

2300

200

1200

449TS

575

RGZESDI

Ball

4:1

1LA04496VT52 19280

SA-7INV

226

95

2300

CT DE Speed Bearing Range

FL Nom. Eff. (%)

Part Number

4:1

1LA03262VT42

4652

SA-7INV

55

93.6

600

4:1

1LA03262VT52

4652

SA-7INV

55

93.6

600

Ball

4:1

1LA03264VT41

4250

SA-7INV

58

93.6

600

Ball

4:1

1LA03264VT51

4250

SA-7INV

58

93.6

600

RGZESDI

Ball

4:1

1LA03656VT41

6412

SA-7INV

66

93.6

850

RGZESDI

Ball

4:1

1LA03656VT51

6412

SA-7INV

66

93.6

850

460

RGZESDI

Ball

4:1

9129

SA-7INV

67

91.7

1100

200

900

449TS

460

RGZESDI

Ball

4:1

21100

SA-7INV

241

94.5

2600

404T

575

RGZESDI

Ball

4:1

9129

SA-7INV

67

91.7

1100

200

900

449TS

575

RGZESDI

Ball

4:1

21100

SA-7INV

241

94.5

2600

3600

364TS

460

RGZESDI

Ball

4:1

1LA03642VT42

6370

SA-7INV

68

93.6

831

250

3600

449TS

460

RGZESDI

Ball

4:1

1LA04492VT42 22848

SA-7INV

267

95.4

2600

3600

364TS

575

RGZESDI

Ball

4:1

1LA03642VT52

6370

SA-7INV

68

93.6

831

250

3600

449TS

575

RGZESDI

Ball

4:1

1LA04492VT52 22848

SA-7INV

267

95.4

2600

60

1800

364T

460

RGZESDI

Ball

4:1

1LA03644VT41

5819

SA-7INV

71

93.6

831

250

1800

449TS

460

RGZESDI

Ball

4:1

1LA04494VT42 19890

SA-7INV

281

95.8

2600

60

1800

364T

575

RGZESDI

Ball

4:1

1LA03644VT51

5819

SA-7INV

71

93.6

831

250

1800

449TS

575

RGZESDI

Ball

4:1

1LA04494VT52 19890

SA-7INV

281

95.8

2600

60

1200

404T

460

RGZESDI

Ball

4:1

1LA04046VT41

8256

SA-7INV

74

94.1

1135

✔

250

1200

449TS

460

RGZESDI

Ball

4:1

1LA04496VE42

21989

SA-7INV

280

95

2600

60

1200

404T

575

RGZESDI

Ball

4:1

1LA04046VT51

8256

SA-7INV

74

94.1

1100

✔

250

1200

449TS

575

RGZESDI

Ball

4:1

1LA04496VE52

21989

SA-7INV

280

95

2600

RPM Frame Voltage

Type

50

3600

326TS

460

RGZESDI

Ball

50

3600

326TS

575

RGZESDI

Ball

50

1800

326T

460

RGZESDI

50

1800

326T

575

RGZESDI

50

1200

365T

460

50

1200

365T

575

50

900

404T

50

900

60 60

✔ ✔

✔ ✔

Type

List Price $

Part Number

FL Mult. Sym. Amps

Weight (lbs.)

900

405T

460

RGZESDI

Ball

4:1

12065

SA-7INV

67

91.7

1250

250

900 S449SS

460

RGZESDI

Ball

4:1

31200

SA-7INV

303

94.5

3050

900

405T

575

RGZESDI

Ball

4:1

12065

SA-7INV

67

91.7

1250

250

900 S449SS

575

RGZESDI

Ball

4:1

31200

SA-7INV

303

94.5

3050

75

3600

365TS

460

RGZESDI

Ball

4:1

1LA03652VT42

7875

SA-7INV

85

94.1

875

75

3600

365TS

575

RGZESDI

Ball

4:1

1LA03652VT52

7875

SA-7INV

85

94.1

875

75

1800

365T

460

RGZESDI

Ball

4:1

1LA03654VT41

7185

SA-7INV

87

94.1

875

75

1800

365T

575

RGZESDI

Ball

4:1

1LA03654VT51

7185

SA-7INV

87

94.1

875

75

1200

405T

460

RGZESDI

Ball

4:1

1LA04056VT41

9636

SA-7INV

93

94.5

1300

1LA04056VT51

✔ ✔ ✔

300

3600

449TS

460

RGZESDI

Ball

4:1

1LA04492VE42

28019

SA-7INV

323

95.8

2600

300

3600

449TS

575

RGZESDI

Ball

4:1

1LA04492VE52

28019

SA-7INV

323

95.8

2600

300

1800

449TS

460

RGZESDI

Ball

4:1

1LA04494VE42

22563

SA-7INV

346

95.4

2600

300

1800

449TS

575

RGZESDI

Ball

4:1

1LA04494VE52

22563

SA-7INV

346

95.4

2600

300

1200 S449SS

460

RGZESDI

Ball

4:1

37402

SA-7INV

335

95

3050

1200

405T

575

RGZESDI

Ball

4:1

9636

SA-7INV

93

94.5

1300

300

1200 S449SS

575

RGZESDI

Ball

4:1

37402

SA-7INV

335

95

3050

900

444TS

460

RGZESDI

Ball

4:1

13540

SA-7INV

94

93

1625

350

3600 S449SS

460

RGZESDI

4:1

1LA03502VG42 34762

SA-7INV

369

95.4

3063

75

900

444TS

575

RGZESDI

Ball

4:1

13540

SA-7INV

94

93

1625

350

3600 S449SS

575

RGZESDI

Ball 1 Ball 1

4:1

1LA03502VG52 34762

SA-7INV

369

95.4

3063

100 3600

405TS

460

RGZESDI

Ball

4:1

1LA04052VT42 10779

SA-7INV

108

94.1

1300

350

1800 S449SS

460

RGZESDI

Ball

4:1

1LA03504VG42 32312

SA-7INV

390

95.8

3309

100 3600

405TS

575

RGZESDI

Ball

4:1

1LA04052VT52 10779

SA-7INV

108

94.1

1300

350

1800 S449SS

575

RGZESDI

Ball

4:1

1LA03504VG52 32312

SA-7INV

390

95.8

3309

100 1800

405T

460

RGZESDI

Ball

4:1

1LA04054VT41

8987

SA-7INV

113

94.5

1300

100 1800

405T

575

RGZESDI

Ball

4:1

1LA04054VT51

8987

SA-7INV

113

94.5

1300

100 1200

444TS

460

RGZESDI

Ball

4:1

1LA04446VT42 11932

SA-7INV

117

94.5

1625

100 1200

444TS

575

RGZESDI

Ball

4:1

1LA04446VT52 11932

SA-7INV

117

94.5

100

900

445TS

460

RGZESDI

Ball

4:1

16253

SA-7INV

123

100

900

445TS

575

RGZESDI

Ball

4:1

16253

SA-7INV

123

125 3600

444TS

460

RGZESDI

Ball

4:1

1LA04442VT42 12814

SA-7INV

125 3600

444TS

575

RGZESDI

Ball

4:1

1LA04442VT52 12814

SA-7INV

125 1800

444TS

460

RGZESDI

Ball

4:1

1LA04444VT42 11717

125 1800

444TS

575

RGZESDI

Ball

4:1

1LA04444VT52 11717

125 1200

445TS

460

RGZESDI

Ball

4:1

125 1200

445TS

575

RGZESDI

Ball

4:1

125

900

447TS

460

RGZESDI

Ball

125

900

447TS

575

RGZESDI

Ball

150 3600

445TS

460

RGZESDI

150 3600

445TS

575

150 1800

445TS

150 1800

445TS

150 1200 150 1200 150 150

4-6

✔ ✔

350

1200 S449SS

460

RGZESDI

Ball

4:1

42342

SA-7INV

396

95

3869

350

1200 S449SS

575

RGZESDI

Ball

4:1

42342

SA-7INV

396

95

3869

400

3600 S449SS

460

RGZESDI

4:1

1LA04002VG42 38805

SA-7INV

418

95.4

3217

1625

400

3600 S449SS

575

RGZESDI

Ball 1 Ball 1

4:1

1LA04002VG52 38805

SA-7INV

418

95.4

3217

94.1

1740

400

1800 S449SS

460

RGZESDI

Ball

4:1

1LA04004VG42 36065

SA-7INV

449

95.8

3869

94.1

1740

400

1800 S449SS

575

RGZESDI

Ball

4:1

1LA04004VG52 36065

SA-7INV

449

95.8

3869

138

94.5

1625

138

94.5

1625

SA-7INV

143

95

1625

SA-7INV

143

95

1625

1LA04456VT42 14390

SA-7INV

144

94.5

1740

1LA04456VT52 14390

SA-7INV

144

94.5

1740

4:1

16181

SA-7INV

152

93.6

2000

4:1

16181

SA-7INV

152

93.6

2000

Ball

4:1

1LA04452VT42 13434

SA-7INV

164

95

1740

RGZESDI

Ball

4:1

1LA04452VT52 13434

SA-7INV

164

95

1740

460

RGZESDI

Ball

4:1

1LA04454VT42 13434

SA-7INV

170

95.8

1740

575

RGZESDI

Ball

4:1

1LA04454VT52 13434

SA-7INV

170

95.8

1740

447TS

460

RGZESDI

Ball

4:1

1LA04476VT42 15963

SA-7INV

170

95

2000

447TS

575

RGZESDI

Ball

4:1

1LA04476VT52 15963

SA-7INV

170

95

2000

900

447TS

460

RGZESDI

Ball

4:1

21600

SA-7INV

186

94.1

2280

900

447TS

575

RGZESDI

Ball

4:1

21600

SA-7INV

186

94.1

2280

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

✔

✔ ✔

✔ ✔ ✔

✔ ✔

✔ ✔

✔ ✔

1 CW rotation facing opposite drive end

✔ ✔

✔ ✔ ✔

2007 Low Voltage AC Motors Selection and Pricing Guide

4-7

Dimensions

75 75

✔

Typical Performance

60 60

Stock Model

Modifications Accessories

Modifications Accessories

Stock/Modifiable

List Price $

HP

FL Mult. Sym. Amps

RGZESDI - Variable Torque/Constant Torque

Lead Time

Typical Performance

CT DE Speed Bearing Range

Stock/Modifiable

INVERTER Duty Hazardous Duty

Dimensions

RGZESDI - Variable Torque/Constant Torque

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Inverter Duty High Efficiency Severe Duty TEFC motors are designed for inverter or vector applications where up to a 10:1 constant torque speed range is required. These motors are well suited to be used in adjustable speed applications such as mixers, machine tools, chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical.

Performance Specifications

Features for Long Life

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-S449 frames have a drive end shaft V-ring slinger.

Specifications table begins on the next page

4-8

2007 Low Voltage AC Motors Selection and Pricing Guide

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Part Number 1LA01444VT41 1LA01456VT41

HP 1

RPM 1800

Frame 143T

1

1200

145T

460

RGZESDI

Ball

1

900

182T

460

RGZESDI

Ball

1.5

3600

143T

460

RGZESDI

Ball

1.5

1800

145T

460

RGZESDI

Ball

1.5

1200

182T

460

RGZESDI

Ball

1.5

900

184T

460

RGZESDI

Ball

2

3600

145T

460

RGZESDI

Ball

2

1800

145T

460

RGZESDI

Ball

2

1200

184T

460

RGZESDI

Ball

1LA01846VT41

2

900

213T

460

RGZESDI

Ball

3

3600

182T

460

RGZESDI

Ball

3

1800

182T

460

RGZESDI

Ball

3

1200

213T

460

RGZESDI

Ball

1LA02136VT41

3

900

215T

460

RGZESDI

Ball

5

3600

184T

460

RGZESDI

Ball

5

1800

184T

460

RGZESDI

Ball

5

1200

215T

460

RGZESDI

Ball

1LA02156VT41

5

900

256T

460

RGZESDI

Ball

7.5

3600

213T

460

RGZESDI

Ball

7.5

1800

213T

460

RGZESDI

Ball

7.5

1200

256T

460

RGZESDI

Ball

7.5

900

284T

460

RGZESDI

Ball

10

3600

215T

460

RGZESDI

Ball

1LA02152VT41

10

1800

215T

460

RGZESDI

Ball

1LA02154VT41

10

1200

284T

460

RGZESDI

List Price $ 775

Multiplier Symbol SA-7INV

FL Amps 460V 1.5

FL Nom. Eff. (%) 82.5

Weight (lbs.) 45

Stock Model ✔ ✔

855

SA-7INV

1.8

80

55

1180

SA-7INV

1.9

78.5

85

1LA01442VT41

875

SA-7INV

2

82.5

45

✔

1LA01454VT41

805

SA-7INV

2.2

84

55

✔

1LA01826VT41

1005

SA-7INV

2.3

85.5

85

✔

1385

SA-7INV

2.6

80

100

1LA01452VT41

910

SA-7INV

2.5

84

55

✔

1LA01464VT41

840

SA-7INV

2.9

84

62

✔

1075

SA-7INV

3

86.5

100

✔

1540

SA-7INV

3.3

82.5

135

1LA01822VT41

1070

SA-7INV

3.6

86.5

85

✔

1LA01824VT41

985

SA-7INV

3.9

87.5

85

✔

1185

SA-7INV

4

87.5

135

✔

1850

SA-7INV

4.7

84

162

1LA01842VT41

1178

SA-7INV

5.8

87.5

100

✔

1LA01844VT41

1085

SA-7INV

6.5

87.5

100

✔

1515

SA-7INV

6.8

88.5

160

✔

2650

SA-7INV

7.5

86.5

300

1LA02132VT41

1395

SA-7INV

8.8

88.5

151

✔

1LA02134VT41

1275

SA-7INV

9.5

89.5

157

✔

2165

SA-7INV

9.8

90.2

300

2990

SA-7INV

12

87.5

336

1595

SA-7INV

12

89.5

160

✔

1455

SA-7INV

13

89.5

160

✔

Ball

2785

SA-7INV

13

89.5

380

10

900

286T

460

RGZESDI

Ball

3350

SA-7INV

15

91

410

15

3600

256T

460

RGZESDI

Ball

2301

SA-7INV

17

90.2

295

15

1800

256T

460

RGZESDI

Ball

2215

SA-7INV

19

91.7

295

15

1200

286T

460

RGZESDI

Ball

3256

SA-7INV

20

91

450

15

900

324T

460

RGZESDI

Ball

4068

SA-7INV

23

91

565

20

3600

284TS

460

RGZESDI

Ball

3089

SA-7INV

23

90.2

380

20

1800

284T

460

RGZESDI

Ball

2576

SA-7INV

26

91.7

380

20

1200

324T

460

RGZESDI

Ball

3966

SA-7INV

26

91.7

565

20

900

326T

460

RGZESDI

Ball

4730

SA-7INV

31

91

600

25

3600

286TS

460

RGZESDI

Ball

3516

SA-7INV

29

91.7

450

25

1800

286T

460

RGZESDI

Ball

3175

SA-7INV

29

93

450

25

1200

326T

460

RGZESDI

Ball

4465

SA-7INV

33

92.4

600

25

900

364T

460

RGZESDI

Ball

5598

SA-7INV

38

90.2

830

30

3600

324TS

460

RGZESDI

Ball

4120

SA-7INV

34

91.7

565

30

1800

324T

460

RGZESDI

Ball

3590

SA-7INV

35

93

565

30

1200

364T

460

RGZESDI

Ball

5785

SA-7INV

39

92.4

830

30

900

365T

460

RGZESDI

Ball

6769

SA-7INV

47

91

850

40

3600

326TS

460

RGZESDI

Ball

4762

SA-7INV

45

93.6

600

40

1800

326T

460

RGZESDI

Ball

4360

SA-7INV

47

93.6

600

40

1200

365T

460

RGZESDI

Ball

6522

SA-7INV

52

93.6

850

40

900

404T

460

RGZESDI

Ball

9239

SA-7INV

63

91.7

1000

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to S449.

Insulation – Proprietary inverter-duty Class F non-hygroscopic (corona resistant) insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. All motors are equipped with two series connected, normally closed, Class F thermostats for detection of overload conditions and/or excessive heating. Suitable for operation from adjustable speed drives with an insulation system that meets or exceeds NEMA MG1-2003, Part 31.

Voltage 460

DE Type Bearing RGZESDI Ball

Typical Performance

•1 to 350 HP •1.15 service factor on sine wave power, 40ºC ambient •1.0 service factor on inverter power •3600, 1800, 1200 or 900 RPM •3 phase, 60 Hz, 460 volt; 200, 230 & 575 volt available •Meets or exceeds EPAct Efficiency standards •Class F insulation, Class B temperature rise •Continuous Duty •143T through S449 frame

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Stock/Modifiable

Modifications Accessories

Modifications Accessories

RGZESDI - 10:1 Constant Torque

Lead Time

Typical Performance

RGZESDI - 10:1 Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

4-9

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Frame

Voltage

Type

Part Number

Multiplier Symbol

FL Amps 460V

FL Nom. Eff. (%)

Weight (lbs.)

50

3600 364TS

460

RGZESDI

Ball

6480

SA-7INV

55

93.6

830

50

1800 364T

460

RGZESDI

Ball

5929

SA-7INV

58

93.6

830

50

1200 404T

460

RGZESDI

Ball

8366

SA-7INV

66

93.6

1100

50

900 405T

460

RGZESDI

Ball

12175

SA-7INV

67

91.7

1250

60

3600 365TS

460

RGZESDI

Ball

7985

SA-7INV

68

93.6

850

60

1800 365T

460

RGZESDI

Ball

7295

SA-7INV

71

93.6

850

60

1200 405T

460

RGZESDI

Ball

9746

SA-7INV

74

94.1

1250

60

900 444TS

460

RGZESDI

Ball

13650

SA-7INV

78

91.7

1620

75

3600 405TS

460

RGZESDI

Ball

10889

SA-7INV

85

94.1

1250

75

1800 405T

460

RGZESDI

Ball

9097

SA-7INV

87

94.1

1250

75

1200 444TS

460

RGZESDI

Ball

12042

SA-7INV

93

94.5

1620

75

900 445TS

460

RGZESDI

Ball

16363

SA-7INV

94

93

1740

100

3600 444TS

460

RGZESDI

Ball

12924

SA-7INV

108

94.1

1620

100

1800 444TS

460

RGZESDI

Ball

11827

SA-7INV

113

94.5

1620

100

1200 445TS

460

RGZESDI

Ball

14500

SA-7INV

117

94.5

1740

100

900 447TS

460

RGZESDI

Ball

16291

SA-7INV

123

94.1

2000

125

3600 445TS

460

RGZESDI

Ball

13544

SA-7INV

138

94.5

2740

1800 445TS

460

RGZESDI

Ball

13544

SA-7INV

143

95

1740

1200 447TS

460

RGZESDI

Ball

16073

SA-7INV

144

94.5

2000 2000

Inverter Duty High Efficiency Severe Duty TEFC & TEBC (blower cooled) motors are designed for inverter or vector applications where up to a 1000:1 constant torque speed range is required. These motors are well suited to be used in adjustable speed applications such as mixers, machine tools, chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical.

Performance Specifications •1 to 400 HP •1.15 service factor on sine wave power, 40ºC ambient •1.0 service factor on inverter power •3600, 1800, 1200 or 900 RPM •3 phase, 60 Hz, 460 volt; 200, 230 & 575 volt available •Meets or exceeds EPAct Efficiency standards •Class F insulation, Class B temperature rise •Continuous Duty •143T through S449 frame

900 447TS

460

RGZESDI

Ball

21710

SA-7INV

152

93.6

3600 447TS

460

RGZESDI

Ball

18580

SA-7INV

164

95

1740

150

1800 447TS

460

RGZESDI

Ball

16198

SA-7INV

170

95.8

2000

150

1200 449TS

460

RGZESDI

Ball

19390

SA-7INV

170

95

2300

Features for Long Life Frame & End Shields – Cast iron construction for exceptional structural integrity with condensation T-drains. Lifting eyebolts are included for frames 213T to S449.

150

900 449TS

460

RGZESDI

Ball

21210

SA-7INV

186

94.1

2300

200

3600 449TS

460

RGZESDI

Ball

22958

SA-7INV

223

95

2300 2300

200

1800 449TS

460

RGZESDI

Ball

20000

SA-7INV

239

95.8

200

1200 449TS

460

RGZESDI

Ball

22099

SA-7INV

238

95

2300

250

3600 449TS

460

RGZESDI

Ball

28189

SA-7INV

282

95.4

2300

250

1800 449TS

460

RGZESDI

Ball

22673

SA-7INV

302

95.8

2300

250

1200 S449SS

460

RGZESDI

Ball

37512

SA-7INV

296

95

3050

300

3600 S449SS

460

RGZESDI

Ball

34872

SA-7INV

333

95.8

3063

300

1800 S449SS

460

RGZESDI

Ball

32422

SA-7INV

356

95.4

3050

350

3600 S449SS

460

RGZESDI

Ball

38915

SA-7INV

392

95.4

3050

350

1800 S449SS

460

RGZESDI

Ball

36175

SA-7INV

406

95.8

3050

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Insulation – Proprietary inverter-duty Class F non-hygroscopic (corona resistant) insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. All motors are equipped with two series connected, normally closed, Class F thermostats for detection of overload conditions and/or excessive heating. Suitable for operation from adjustable speed drives with an insulation system that meets or exceeds NEMA MG1-2003, Part 31. Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. TEBC motors will be supplied with a TENV motor to provide the cooling required for operation at low rotational speeds. Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-S449 frames have a drive end shaft V-ring slinger.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split, neoprene gasketed and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Specifications table begins on the next page

4-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

4-11

Dimensions

125 150

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Typical Performance

125 125

Stock Model

Modifications Accessories

Modifications Accessories

RPM

List Price $

RGZESDI - 1000:1 Constant Torque

Lead Time

Typical Performance

HP

Stock/Modifiable

INVERTER Duty Hazardous Duty

Dimensions

RGZESDI - 10:1 Constant Torque DE Bearing

INVERTER Duty Severe Duty

Severe Duty - TEFC & TEBC Motors

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

RPM Frame Voltage

1

1800

145T

460

RGKESDI

Ball

TEFC

1

1200

182T

460

RGKESDI

Ball

TEFC

1.5

3600

182T

460

RGKESDI

Ball

TEFC

1.5

1800

182T

460

RGKESDI

Ball

TEFC

Part Number 1LA01454VK41

1LA01824VK41

FL Amps Mult. Sym. 460V

FL Nom. Eff. (%)

Weight (lbs.)

Stock Model ✔

805

SA-7INV

1.4

82.5

55

1005

SA-7INV

1.8

80

85

1070

SA-7INV

2

82.5

85

895

SA-7INV

2.2

84

85

✔

HP

RPM Frame Voltage

Type

FL Nom. Eff. (%)

Weight Stock (lbs.) Model

3600

364TS

460

RGZESDI

Ball

TEBC

8141

SA-7INV

68

93.6

910

1800

364T

460

RGZESDI

Ball

TEBC

7540

SA-7INV

71

93.6

910

60

1200

404T

460

RGZESDI

Ball

TEBC

11029

SA-7INV

72

94.1

1180

60

900

405T

460

RGZESDI

Ball

TEBC

13655

SA-7INV

78

91.7

1330

75

3600

365TS

460

RGZESDI

Ball

TEBC

9789

SA-7INV

85

94.1

930

184T

460

RGKESDI

Ball

TEFC

1075

SA-7INV

2.4

85.5

100

184T

460

RGKESDI

Ball

TEFC

1178

SA-7INV

2.5

84

100

2

1800

182T

460

RGKESDI

Ball

TEFC

985

SA-7INV

2.7

84

85

2

1200

213T

460

RGKESDI

Ball

TEFC

1205

SA-7INV

3.2

86.5

3

3600

213T

460

RGKESDI

Ball

TEFC

1395

SA-7INV

3.7

86.5

3

1800

184T

460

RGKESDI

Ball

TEFC

1085

SA-7INV

4.2

87.5

100

100 1800

405T

460

RGZESDI

3

1200

215T

460

RGKESDI

Ball

TEFC

1515

SA-7INV

4.3

87.5

162

100 1200

444TS

460

RGZESDI

5

3600

215T

460

RGKESDI

Ball

TEFC

1595

SA-7INV

5.8

87.5

162

100

900

445TS

460

RGZESDI

5

1800

213T

460

RGKESDI

Ball

TEFC

1275

SA-7INV

6.5

87.5

157

125 3600

444TS

460

5

1200

254T

460

RGKESDI

Ball

TEFC

1775

SA-7INV

7.1

88.5

250

125 1800

444TS

5

900

254T

460

RGZESDI

Ball

TEBC

3817

SA-7INV

7.5

86.5

330

125 1200

7.5

3600

254T

460

RGKESDI

Ball

TEFC

125

7.5

1800

254T

460

RGKESDI

Ball

TEFC

7.5

1200

256T

460

RGKESDI

Ball

7.5

900

256T

460

RGZESDI

10

3600

256T

460

RGKESDI

10

1800

256T

460

10

1200

256T

10

900

15

3600

15 15

75

1800

365T

460

RGZESDI

Ball

TEBC

9038

SA-7INV

87

94.1

930

75

1200

405T

460

RGZESDI

Ball

TEBC

12155

SA-7INV

87

94.5

1330

130

75

900

444TS

460

RGZESDI

Ball

TEBC

15140

SA-7INV

94

93

1700

130

100 3600

405TS

460

RGZESDI

Ball

TEBC

11936

SA-7INV

110

94.1

1330

Ball

TEBC

11014

SA-7INV

113

94.5

1330

Ball

TEBC

15279

SA-7INV

115

94.5

1700

Ball

TEBC

16573

SA-7INV

123

94.1

1820

RGZESDI

Ball

TEBC

15089

SA-7INV

136

94.5

1700

460

RGZESDI

Ball

TEBC

13890

SA-7INV

143

95

1700

445TS

460

RGZESDI

Ball

TEBC

17342

SA-7INV

144

94.5

1820 2080

✔

✔

✔

SA-7INV

8.7

88.5

250

SA-7INV

9.5

89.5

245

TEFC

2112

SA-7INV

10

90.2

Ball

TEBC

4140

SA-7INV

12

Ball

TEFC

2191

SA-7INV

12.5

RGKESDI

Ball

TEFC

2105

SA-7INV

12.5

89.5

285

460

RGZESDI

Ball

TEBC

3405

SA-7INV

13

90.2

330

284T

460

RGZESDI

Ball

TEBC

4590

SA-7INV

15

91

460

200 1200

449TS

460

RGZESDI

254T

460

RGZESDI

Ball

TEBC

2972

SA-7INV

18

90.2

330

200

900

449TS

460

RGZESDI

1800

254T

460

RGZESDI

Ball

TEBC

2154

SA-7INV

20

91.7

330

250 3600

449TS

460

RGZESDI

1200

284T

460

RGZESDI

Ball

TEBC

4285

SA-7INV

20

91

460

250 1800

449TS

460

RGZESDI

15

900

286T

460

RGZESDI

Ball

TEBC

4840

SA-7INV

23

91

530

250 1200

449TS

460

20

3600

256T

460

RGZESDI

Ball

TEBC

3265

SA-7INV

23

90.2

375

250

900 S449SS

20

1800

256T

460

RGZESDI

Ball

TEBC

2557

SA-7INV

27

91.7

375

300 3600

20

1200

286T

460

RGZESDI

Ball

TEBC

4319

SA-7INV

26

91.7

530

300 1800

20

900

324T

460

RGZESDI

Ball

TEBC

5558

SA-7INV

31

91

25

3600 284TS

460

RGZESDI

Ball

TEBC

3816

SA-7INV

29

91.7

25

1800

284T

460

RGZESDI

Ball

TEBC

3561

SA-7INV

29

25

1200

324T

460

RGZESDI

Ball

TEBC

5460

SA-7INV

33

25

900

326T

460

RGZESDI

Ball

TEBC

6220

SA-7INV

30

3600 286TS

460

RGZESDI

Ball

TEBC

4217

30

1800

286T

460

RGZESDI

Ball

TEBC

30

1200

326T

460

RGZESDI

Ball

30

900

364T

460

RGZESDI

Ball

40

3600 324TS

460

RGZESDI

40

1800

324T

460

40

1200

364T

460

40

900

365T

50

900

447TS

460

RGZESDI

Ball

TEBC

19777

SA-7INV

152

93.6

150 3600

445TS

460

RGZESDI

Ball

TEBC

17152

SA-7INV

160

95

1820

300

150 1800

445TS

460

RGZESDI

Ball

TEBC

15765

SA-7INV

169

95.8

1820

87.5

375

150 1200

447TS

460

RGZESDI

Ball

TEBC

20533

SA-7INV

169

95

2080

89.5

300

150

900

447TS

460

RGZESDI

Ball

TEBC

20888

SA-7INV

186

94.1

2080

200 3600

447TS

460

RGZESDI

Ball

TEBC

20940

SA-7INV

208

95

2080

200 1800

447TS

460

RGZESDI

Ball

TEBC

18666

SA-7INV

223

95.8

2080

Ball

TEBC

28971

SA-7INV

222

95

2380

Ball

TEBC

29444

SA-7INV

241

94.5

2380

Ball

TEBC

25509

SA-7INV

264

95.4

2380

Ball

TEBC

23417

SA-7INV

282

95.8

2380

RGZESDI

Ball

TEBC

31721

SA-7INV

285

95

2380

460

RGZESDI

Ball

TEBC

42555

SA-7INV

303

94.5

4130

449TS

460

RGZESDI

Ball

TEBC

33369

SA-7INV

330

95.8

2380

449TS

460

RGZESDI

Ball

TEBC

26337

SA-7INV

345

95.4

2380

645

300 1200 S449SS

460

RGZESDI

Ball

TEBC

40542

SA-7INV

335

95

4130

4600

350 3600 S449SS

460

RGZESDI

Ball1

TEBC

37910

SA-7INV

370

95.4

4130

93

460

350 1800 S449SS

460

RGZESDI

Ball

TEBC

33732

SA-7INV

390

95.8

4130

92.4

645

350 1200 S449SS

460

RGZESDI

Ball

TEBC

45482

SA-7INV

396

95

4130

38

90.2

680

400 3600 S449SS

460

RGZESDI

Ball

TEBC

41945

SA-7INV

420

95.4

4130

SA-7INV

34

91.7

680

400 1800 S449SS

460

RGZESDI

Ball

TEBC

39205

SA-7INV

450

95.8

4130

3926

SA-7INV

35

93

680

TEBC

6444

SA-7INV

39

92.4

680

TEBC

7088

SA-7INV

47

91

910

Ball

TEBC

5341

SA-7INV

46

93.6

645

RGZESDI

Ball

TEBC

4964

SA-7INV

47

93.6

645

RGZESDI

Ball

TEBC

8294

SA-7INV

52

93.6

910

460

RGZESDI

Ball

TEBC

9578

SA-7INV

63

91.7

930

3600 326TS

460

RGZESDI

Ball

TEBC

6325

SA-7INV

55

93.6

680

50

1800

326T

460

RGZESDI

Ball

TEBC

5858

SA-7INV

58

93.6

680

50

1200

365T

460

RGZESDI

Ball

TEBC

9942

SA-7INV

66

93.6

930

50

900

404T

460

RGZESDI

Ball

TEBC

10729

SA-7INV

67

91.7

1180

1LA02564VK41

✔

✔

1

Dimensions

1840 1740

1LA02544VK41

Typical Performance

1200 3600

1LA02134VK41

FL Amps Mult. Sym. 460V

60

2

1LA01844VK41

Part Number

List Price $

60

1.5

1LA01834VK41

DE Bearing Enclosure

Stock/Modifiable

Modifications Accessories

Modifications Accessories

HP

List Price $

RGKESDI & RGZESDI - 1000:1 Constant Torque

Lead Time

Typical Performance

Type

DE Bearing Enclosure

Stock/Modifiable

1 CW rotation facing opposite drive end

RGKESDI motors can be offered as TENV in the same frame as TEFC.

4-12

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

INVERTER Duty Hazardous Duty

Dimensions

RGKESDI & RGZESDI - 1000:1 Constant Torque

INVERTER Duty Severe Duty

Severe Duty - TEFC & TEBC Motors

Severe Duty - TEFC & TEBC Motors

4-13

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

These high efficiency explosion-proof motors are UL® listed for dust ignition proof environments, and are suitable for use in Class I, Group D, Class II, Groups F & G, Division 1 hazardous areas. They are ideal for use in applications such as chemical processing, mining, foundry, pulp and paper, waste management, and petro/chemical.

Performance Specifications •1 to 300 HP •1.0 service factor, 40ºC ambient •T3B temperature code •900, 1200, 1800, or 3600 RPM •3 phase, 60 Hz; 230/460 volt operation under 25 HP, •460 volt 25 HP and above; 200 & 575 volt available •Class F insulation, Class B temperature rise •NEMA design B, continuous duty •143T through 449T frame

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes. Bearings – Regreasable, oversized single shielded bearings with cast iron inner caps. Alemite grease fittings on the inlets, and pipe plugs on the relief ports for ease of routine maintenance. Frames 143T – 256T are equipped with a shaft seal on the drive end; 284T – 449T frames have a drive end V-ring slinger for added bearing life.

Specifications table begins on the next page

4-14

2007 Low Voltage AC Motors Selection and Pricing Guide

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases. Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Multiplier Symbol SA-7XXP

FL Amps 460V 1.5

1MJ01454VT41

687

SA-7XXP

1.7

FL Nom. Eff. (%) 82.5

Stock Model

83.6

70

✔

1.7

85.5

125

1.9

78.5

130

SA-7XXP

1.9

84

70

728

SA-7XXP

2.5

84

70

Ball

884

SA-7XXP

2.6

86.2

Ball

1744

SA-7XXP

2.8

80

170

RGZZESDI

Ball

810

SA-7XXP

2.6

86.5

100

460

RGZZESDI

Ball

807

SA-7XXP

3

87.5

100

460

RGZZESDI

Ball

1055

SA-7XXP

2.8

88.5

170

HP 1

RPM 3600

Frame 143T

1

1800

145T

460

RGZZESDI

Ball

1

1200

182T

460

RGZZESDI

Ball

795

SA-7XXP

1

900

184T

460

RGZZESDI

Ball

1523

SA-7XXP

1.5

3600

145T

460

RGZZESDI

Ball

750

1.5

1800

145T

460

RGZZESDI

Ball

1.5

1200

184T

460

RGZZESDI

1.5

900

213T

460

RGZZESDI

2

3600

182T

460

2

1800

182T

2

1200

213T

1MJ01464VT41

1MJ01824VT41

130

2

900

215T

460

RGZZESDI

Ball

2075

SA-7XXP

3.5

82.5

180

3

3600

184T

460

RGZZESDI

Ball

966

SA-7XXP

3.6

87.5

115

3

1800

184T

460

RGZZESDI

Ball

891

SA-7XXP

4.6

87.5

115

3

1200

215T

460

RGZZESDI

Ball

1342

SA-7XXP

4.4

89.5

180

1MJ01844VT41

3

900

254T

460

RGZZESDI

Ball

2161

SA-7XXP

5.5

84

290

5

3600

213T

460

RGZZESDI

Ball

1146

SA-7XXP

6.2

88.5

160

5

1800

213T

460

RGZZESDI

Ball

1141

SA-7XXP

7.3

89.5

160

5

1200

254T

460

RGZZESDI

Ball

1711

SA-7XXP

7

90.2

290

1MJ02134VT41

5

900

256T

460

RGZZESDI

Ball

2625

SA-7XXP

9

86.5

360

7.5

3600

215T

460

RGZZESDI

Ball

1281

SA-7XXP

9.2

89.5

180

7.5

1800

215T

460

RGZZESDI

Ball

1304

SA-7XXP

10.7

89.5

180 360

1MJ02154VT41

7.5

1200

256T

460

RGZZESDI

Ball

2003

SA-7XXP

10

90.2

7.5

900

284T

460

RGZZESDI

Ball

3151

SA-7XXP

12

87.5

450

10

3600

254T

460

RGZZESDI

Ball

1671

SA-7XXP

11.8

90.2

265

10

1800

254T

460

RGZZESDI

Ball

1648

SA-7XXP

13.7

91.7

265

10

1200

284T

460

RGZZESDI

Ball

2681

SA-7XXP

14.5

91

450

10

900

286T

460

RGZZESDI

Ball

3937

SA-7XXP

17

91

525

15

3600

256T

460

RGZZESDI

Ball

1976

SA-7XXP

17.6

90.2

325

15

1800

256T

460

RGZZESDI

Ball

1957

SA-7XXP

20

91.7

325

15

1200

286T

460

RGZZESDI

Ball

3148

SA-7XXP

20

91.7

525

15

900

324T

460

RGZZESDI

Ball

4892

SA-7XXP

25

91

660

20

3600

284TS

460

RGZZESDI

Ball

2495

SA-7XXP

23.4

91.7

410

20

1800

284T

460

RGZZESDI

Ball

2407

SA-7XXP

24

93

410

20

1200

324T

460

RGZZESDI

Ball

3900

SA-7XXP

28

92.4

660

20

900

326T

460

RGZZESDI

Ball

5567

SA-7XXP

33

91

690

25

3600

286TS

460

RGZZESDI

Ball

2822

SA-7XXP

28.5

91.7

460

1MJ02544VT41

1MJ02564VT41

1MJ02844VT41

1MJ02864VT41

25

1800

286T

460

RGZZESDI

Ball

2710

SA-7XXP

30

93

460

25

1200

326T

460

RGZZESDI

Ball

4380

SA-7XXP

33

92.4

690

25

900

364T

460

RGZZESDI

Ball

6616

SA-7XXP

41

91

900

30

3600

324TS

460

RGZZESDI

Ball

3750

SA-7XXP

35.3

93.6

589

30

1800

324T

460

RGZZESDI

Ball

3622

SA-7XXP

34

93.6

589

30

1200

364T

460

RGZZESDI

Ball

5924

SA-7XXP

41

93.6

900

30

900

365T

460

RGZZESDI

Ball

7810

SA-7XXP

52

91

915

1MJ03244VT41

✔

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

✔

✔

✔

✔

✔

✔

✔

✔

4-15

Dimensions

Frame & End Shields – Cast iron frame and end shields for exceptional structural integrity, with sintered condensation drains on 404T – 449T frames. Lifting eyebolts are included for frames 213T to 449T.

Insulation – Proprietary Class F nonhygroscopic insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. Varnish system application ensures maximum wire penetration to provide protection from moisture, corrosion and electrical shock. Two series- connected normallyclosed Class B thermostats are supplied as standard.

Part Number

List Price $ 672

Weight (lbs.) 65

Voltage 460

DE Type Bearing RGZZESDI Ball

Typical Performance

Features for Long Life

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Stock/Modifiable

Modifications Accessories

Modifications Accessories

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque

Lead Time

Typical Performance

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

Hazardous Duty Motors

INVERTER Duty Severe Duty

Hazardous Duty Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Frame 326TS

Voltage 460

Part Number 1MJ03264VT41

FL Amps 460V 44.5

FL Nom. Eff. (%) 93.6

Weight (lbs.) 645

Stock Model ✔

40

1800

326T

460

RGZZESDI

Ball

4279

SA-7XXP

48

93.6

645

40

1200

365T

460

RGZZESDI

Ball

6654

SA-7XXP

55

93.6

915

40

900

404T

460

RGZZESDI

Ball

9452

SA-7XXP

53

91.7

1290

50

3600

364TS

460

RGZZESDI

Ball

6023

SA-7XXP

57

93.6

865

50

1800

364T

460

RGZZESDI

Ball

5979

SA-7XXP

60

93.6

865

50

1200

404T

460

RGZZESDI

Ball

1MJ03644VT41

7939

SA-7XXP

61

94.1

1290 1420

✔

Inverter Duty High Efficiency ExplosionProof motors are ideal for both variable torque and constant torque loads, designed for inverter or vector applications; are UL® listed for dust ignition proof environments, and are suitable for use in Class I, Groups C & D, Class II, Groups F & G, Division 1 hazardous areas. These motors are well suited to be used in adjustable speed applications such as chemical processing, mining, foundry, pulp and paper, waste management, and petro/chemical.

405T

460

RGZZESDI

Ball

10626

SA-7XXP

66

91.7

365TS

460

RGZZESDI

Ball

7332

SA-7XXP

69

94.1

915

60

1800

365T

460

RGZZESDI

Ball

7337

SA-7XXP

71

94.1

915

60

1200

405T

460

RGZZESDI

Ball

9115

SA-7XXP

74

94.5

1420

Performance Specifications

60

900

444TS

460

RGZZESDI

Ball

13949

SA-7XXP

77

91.7

1740

75

3600

405TS

460

RGZZESDI

Ball

9813

SA-7XXP

81

94.1

1335

75

1800

405T

460

RGZZESDI

Ball

9148

SA-7XXP

86

94.5

1335

75

1200

444TS

460

RGZZESDI

Ball

12201

SA-7XXP

88

94.5

1740

75

900

445TS

460

RGZZESDI

Ball

16884

SA-7XXP

95

93

1930

100 3600

444TS

460

RGZZESDI

Ball

12786

SA-7XXP

111

94.5

1740

100 1800

444TS

460

RGZZESDI

Ball

11990

SA-7XXP

118

95

1740

100 1200

445TS

460

RGZZESDI

Ball

14726

SA-7XXP

118

94.5

1930

100

900

447TS

460

RGZZESDI

Ball

18168

SA-7XXP

124

94.1

2415

125 3600

445TS

460

RGZZESDI

Ball

15052

SA-7XXP

137

95

1930

125 1800

445TS

460

RGZZESDI

Ball

13690

SA-7XXP

143

95.8

1930

125 1200

447TS

460

RGZZESDI

Ball

16283

SA-7XXP

142

95

2415

•1 to 200 HP •6:1 variable or 6:1 constant torque speed range •1.0 service factor •40ºC ambient •T3C temperature code •3600, 1800, 1200, or 900 RPM •3 phase, 60 Hz; 460 volt; 200, 230 & 575 volt available •Class F insulation •Continuous Duty •143T through 449T frame

125

900

449TS

460

RGZZESDI

Ball

22615

SA-7XXP

159

93.6

2625

150 3600

447TS

460

RGZZESDI

Ball

18913

SA-7XXP

159

95

2415

Features for Long Life

150 1800

447TS

460

RGZZESDI

Ball

16598

SA-7XXP

171

95.8

2415

150 1200

449TS

460

RGZZESDI

Ball

19117

SA-7XXP

170

95

2625

200 3600

449TS

460

RGZZESDI

Ball

22493

SA-7XXP

213

95.4

2625

200 1800

449TS

460

RGZZESDI

Ball

19401

SA-7XXP

223

95.8

2625

Frame & End Shields – Cast iron construction for exceptional structural integrity, with UL® listed breather drains on 404T to 449T frames. Lifting eyebolts are included for frames 213T to 449T.

1MJ03654VT41

1MJ04054VT41

✔

✔

Rotor – A unique offset rotor bar design provides improved efficiency while larger bars and end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced for extended bearing life, and includes a highstrength carbon steel (C1045) shaft for maximum rotor performance.

Cooling – A bi-directional, non-sparking fan is locked and keyed to the shaft. Its low-inertia design reduces windage losses, improves airflow, reduces noise and provides dependable cooling. Cast iron fan covers are provided on all frame sizes.

Oversized Conduit Box – Cast iron construction that is larger than industry standards, diagonally-split and rotatable in 90º increments for quick and easy connections. Includes a ground lug and non-wicking, clearly and permanently marked leads. Corrosion Resistance – Cast iron construction, zinc-plated hardware, epoxy enamel paint and stainless steel nameplate resist rust and corrosion. Modifiable – All Siemens motors are available with a wide variety of modifications to meet your specific motor needs.

Bearings – Regreasable, oversized single shielded with cast iron inner caps. Alemite grease fittings on the inlets and pipe plugs on the relief ports for ease of routine maintenance. For added bearing protection, 143T-256T frames have a drive end shaft seal and 284T-449T frames have a drive end shaft V-ring slinger.

Dimensions

900 3600

Insulation – Proprietary inverter-rated Class F non-hygroscopic (corona resistant) insulation system with NEMA Class B temperature rise, provides an extra margin of thermal life. All motors are equipped with two series connected, normally closed, Class B thermostats for detection of overload conditions and/or excessive heating. Suitable for operation from adjustable speed drives with an insulation system that meets or exceeds NEMA MG1-2003, Part 31.

Lubrication – A specially formulated, high temperature tested, polyurea based grease is used to provide more than four times the lubrication life of other polyurea greases.

Specifications table begins on the next page

4-16

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

Typical Performance

50 60

Stator/Windings – Manufactured with premium electrical grade steel laminations and copper electrical magnet wire to lower losses for improved efficiencies. A unique stator core design lowers flux density while increasing cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Modifications Accessories

Modifications Accessories

RPM 3600

Multiplier Symbol SA-7XXP

Class I, Groups C & D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque

Lead Time

Typical Performance

HP 40

List Price $ 4633

Stock/Modifiable

INVERTER Duty Hazardous Duty

Dimensions

Hazardous Duty Motors

Class I, Group D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque DE Type Bearing RGZZESDI Ball

INVERTER Duty Severe Duty

Hazardous Duty Motors

4-17

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Part Number

List Price $ 912

Multiplier Symbol SA-7XXP

FL Amps 460V 1.5

FL Nom. Eff. (%) 82.5

Weight (lbs.) 65

Stock Model

Class I, Groups C & D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque HP 40

RPM 3600

Frame 326TS

Voltage 460

DE Type Bearing RGZZESDI Ball

Part Number

List Price $ 5301

Multiplier Symbol SA-7XXP

FL Amps 460V 45

Custom Build FL Nom. Eff. (%) 93.6

Weight (lbs.) 645

HP 1

RPM 3600

Frame 143T

1

1800

145T

460

RGZZESDI

Ball

927

SA-7XXP

1.7

83.6

70

40

1800

326T

460

RGZZESDI

Ball

4947

SA-7XXP

48

93.6

645

1

1200

182T

460

RGZZESDI

Ball

1034

SA-7XXP

1.7

85.5

125

40

1200

365T

460

RGZZESDI

Ball

7527

SA-7XXP

55

93.6

915 1290

900

184T

460

RGZZESDI

Ball

1712

SA-7XXP

1.9

78.5

130

40

900

404T

460

RGZZESDI

Ball

10854

SA-7XXP

53

91.7

3600

145T

460

RGZZESDI

Ball

989

SA-7XXP

1.9

84

70

50

3600

364TS

460

RGZZESDI

Ball

6895

SA-7XXP

57

93.6

865

1.5

1800

145T

460

RGZZESDI

Ball

968

SA-7XXP

2.5

84

70

50

1800

364T

460

RGZZESDI

Ball

6851

SA-7XXP

60

93.6

865

1.5

1200

184T

460

RGZZESDI

Ball

1124

SA-7XXP

2.6

86.2

130

50

1200

404T

460

RGZZESDI

Ball

9566

SA-7XXP

61

94.1

1290

1.5

900

213T

460

RGZZESDI

Ball

1047

SA-7XXP

2.8

80

170

50

900

405T

460

RGZZESDI

Ball

12835

SA-7XXP

66

91.7

1420

2

3600

182T

460

RGZZESDI

Ball

1050

SA-7XXP

2.6

86.5

100

60

3600

365TS

460

RGZZESDI

Ball

8204

SA-7XXP

69

94.1

915

2

1800

182T

460

RGZZESDI

Ball

1047

SA-7XXP

3

87.5

100

60

1800

365T

460

RGZZESDI

Ball

8209

SA-7XXP

71

94.1

915

2

1200

213T

460

RGZZESDI

Ball

1330

SA-7XXP

2.8

88.5

170

60

1200

405T

460

RGZZESDI

Ball

10742

SA-7XXP

74

94.5

1420

2

900

215T

460

RGZZESDI

Ball

2350

SA-7XXP

3.5

82.5

180

60

900

444TS

460

RGZZESDI

Ball

16439

SA-7XXP

77

91.7

1740

3

3600

184T

460

RGZZESDI

Ball

1206

SA-7XXP

3.6

87.5

115

75

3600

405TS

460

RGZZESDI

Ball

11440

SA-7XXP

81

94.1

1335

3

1800

184T

460

RGZZESDI

Ball

1192

SA-7XXP

4.6

87.5

115

75

1800

405T

460

RGZZESDI

Ball

10775

SA-7XXP

86

94.5

1335

3

1200

215T

460

RGZZESDI

Ball

1618

SA-7XXP

4.4

89.5

180

75

1200

444TS

460

RGZZESDI

Ball

14042

SA-7XXP

88

94.5

1740

3

900

254T

460

RGZZESDI

Ball

2503

SA-7XXP

5.5

84

290

75

900

445TS

460

RGZZESDI

Ball

19399

SA-7XXP

95

93

1930

5

3600

213T

460

RGZZESDI

Ball

1412

SA-7XXP

6.2

88.5

160

100 3600

444TS

460

RGZZESDI

Ball

14627

SA-7XXP

111

94.5

1740

5

1800

213T

460

RGZZESDI

Ball

1417

SA-7XXP

7.3

89.5

160

100 1800

444TS

460

RGZZESDI

Ball

13831

SA-7XXP

118

95

1740

5

1200

254T

460

RGZZESDI

Ball

2052

SA-7XXP

7

90.2

290

100 1200

445TS

460

RGZZESDI

Ball

16478

SA-7XXP

118

94.5

1930 2415

5

900

256T

460

RGZZESDI

Ball

2457

SA-7XXP

9

86.5

360

100

900

447TS

460

RGZZESDI

Ball

20876

SA-7XXP

124

94.1

7.5

3600

215T

460

RGZZESDI

Ball

1557

SA-7XXP

9.2

89.5

180

125 3600

445TS

460

RGZZESDI

Ball

16893

SA-7XXP

137

95

1930

7.5

1800

215T

460

RGZZESDI

Ball

1579

SA-7XXP

10.7

89.5

180

125 1800

445TS

460

RGZZESDI

Ball

15532

SA-7XXP

143

95.8

1930

7.5

1200

256T

460

RGZZESDI

Ball

2345

SA-7XXP

10

90.2

360

125 1200

447TS

460

RGZZESDI

Ball

18592

SA-7XXP

142

95

2415

7.5

900

284T

460

RGZZESDI

Ball

3800

SA-7XXP

12

87.5

450

125

900

449TS

460

RGZZESDI

Ball

25991

SA-7XXP

159

93.6

2625

3600

254T

460

RGZZESDI

Ball

2012

SA-7XXP

11.8

90.2

265

150 3600

447TS

460

RGZZESDI

Ball

21544

SA-7XXP

159

95

2415

1800

254T

460

RGZZESDI

Ball

1980

SA-7XXP

13.7

91.7

265

150 1800

447TS

460

RGZZESDI

Ball

18907

SA-7XXP

171

95.8

2415

10

1200

284T

460

RGZZESDI

Ball

3165

SA-7XXP

14.5

91

450

150 1200

449TS

460

RGZZESDI

Ball

21777

SA-7XXP

170

95

2625

10

900

286T

460

RGZZESDI

Ball

4664

SA-7XXP

17

91

525

200 3600

449TS

460

RGZZESDI

Ball

25626

SA-7XXP

213

95.4

2625

200 1800

449TS

460

RGZZESDI

Ball

22102

SA-7XXP

223

95.8

2625

15

3600

256T

460

RGZZESDI

Ball

2317

SA-7XXP

17.6

90.2

325

15

1800

256T

460

RGZZESDI

Ball

2299

SA-7XXP

20

91.7

325 525

15

1200

286T

460

RGZZESDI

Ball

3632

SA-7XXP

20

91.7

15

900

324T

460

RGZZESDI

Ball

5657

SA-7XXP

25

91

660

20

3600

284TS

460

RGZZESDI

Ball

2979

SA-7XXP

23.4

91.7

410

20

1800

284T

460

RGZZESDI

Ball

2892

SA-7XXP

24

93

410

20

1200

324T

460

RGZZESDI

Ball

4569

SA-7XXP

28

92.4

660

20

900

326T

460

RGZZESDI

Ball

7467

SA-7XXP

33

91

690

25

3600

286TS

460

RGZZESDI

Ball

3307

SA-7XXP

28.5

91.7

460

25

1800

286T

460

RGZZESDI

Ball

3195

SA-7XXP

30

93

460

25

1200

326T

460

RGZZESDI

Ball

5048

SA-7XXP

33

92.4

690

25

900

364T

460

RGZZESDI

Ball

7656

SA-7XXP

41

91

900

30

3600

324TS

460

RGZZESDI

Ball

4418

SA-7XXP

35.3

93.6

589

30

1800

324T

460

RGZZESDI

Ball

4290

SA-7XXP

34

93.6

589

30

1200

364T

460

RGZZESDI

Ball

6796

SA-7XXP

41

93.6

900

30

900

365T

460

RGZZESDI

Ball

8965

SA-7XXP

52

91

915

4-18

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

10 10

Typical Performance

1 1.5

Stock Model

Modifications Accessories

Modifications Accessories

Voltage 460

DE Type Bearing RGZZESDI Ball

Custom Build

Lead Time

Typical Performance

Class I, Groups C & D, Class II, Groups F & G, Division 1 RGZZESDI - 6:1 Variable or 6:1 Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

Hazardous Duty Motors

INVERTER Duty Severe Duty

Hazardous Duty Motors

4-19

Stock Motor Modifications

Typical Performance

•2 WORKING DAYS* Nameplate change (rerate/derate) Rotation arrow C flange D flange Breather/drain Alemite/grease relief Auxiliary nameplate Fungus proof/tropicalization *2 working days for orders received before noon

•2-4 WEEKS Special testing Special paint Special packaging Bearing change Lubrication/grease change Auxiliary conduit box installation (280 frame and up only) Dowel pin hole Additional drain Additional grounding provision Special thermal protection Klixon® Reconnects (consult factory) Lead cable change/length Convert TEFC to TEAO Terminal block Low noise fan (S449, 2-pole) Change rotation (S449, 2-pole) Oil mist provision Oil mist ready

Dimensions

•5 WORKING DAYS Standard thermostat Routine testing (non-witnessed) Stainless steel hardware Convert F1 to F2 assembly Drip cover Seal lead Space heater Provision for grounding Inpro/Seal® bearing isolator Export packaging Main conduit box rotation Slinger/o-ring seal Brass seal Vertical jacking

4-20

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

SUPER MODIFICATION CAPABILITIES

Typical Performance

CURRENT STANDARD MODIFICATIONS

Modifications Accessories

Modifications Accessories

All stock motor modification lead times are based on warehouse stock motors only, please refer to custom motor section on next page for custom build lead times.

Lead Time

Lead Time

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

INVERTER Duty Severe Duty

Lead Time

INVERTER Duty Severe Duty

Notes

5-1

INVERTER Duty Severe Duty

INVERTER Duty Severe Duty

Modifications/Accessories

Lead Time Custom Motors

Motor Type Page

Altitude

Lead Time Modifications Accessories Typical Performance

X

X

6-3

Nameplates

X

X

X

6-4

Paint

X

6-4

Protective Devices

X

6-5

Rotational Arrows

X

6-5

Service Factor

X

X

6-6

Shafts

X

X

6-6

Shaft Grounding Brush

X

6-7

Shaft Seals

X

6-7

Software

X

6-9

Space Heaters

X

6-9

Testing

X

6-9

Vertical Jacking

X

6-10

Vibration Detectors

X

6-10

Voltage

X

6-10

X X

X

X

X

X

X

X

X

X

X

X

X

X

X

Drip Cover

X

Encoders Export Packaging

X

X

X

X

X

X

X

Grounding

X

X

Hardware

X

X

Fans Flanged Housings/End Shields

Hazardous Duty Motors

X

X X

X

X

X

X

X

X

X

X

X

X

X

X

X

X X

X

X

RG X

6-10

X

6-11

X

6-11

X

X

6-11

X

X

6-12

X

X

X

6-12

X

X

X

X

6-13

X

X

X

6-13

X

X

X

6-13

X

6-14

X

X

6-15

X

X

X

X

6-15

X

X

X

X

6-16

X

X

X

X

6-16

X

X

6-17

X

X

X

X

6-17

X

X

X

X

6-17 Typical Performance

Lead Time (days) = Working days, calculated from normal business hours excluding holidays and weekends, subject to availability of the stock motors and parts at the time of order entry. Modified Motor Pricing Examples: All modifications and accessories shown in this section are the list price additions to ”Modifiable” list prices shown on the preceding pages. Examples of how to construct a list price are shown below.

Dimensions

2007 Low Voltage AC Motors Selection and Pricing Guide

X

X

X

SD DP X X

Modifications Accessories

•CASE B–15 WEEKS DELIVERY P-base motor Tachometer installed Special paint system (formulation) Special shaft material Stearns brake installed

Lubrication

Page GPA GP X

Lead Time

5-2

•CASE A2–14 WEEKS DELIVERY 8-pole motor Bearing RTD (standard) Blower motor Complete test report Multispeed motor NEMA Design C (4 or 6 pole) Teflon® lead wire VPI ACM-1448 (C-4140) shaft material Insulated bearing Ready for tachometer installation Ready for Stearns® brake installation Shaft grounding Special grease Special Inpro/Seal® bearing isolators TENV

6-2

X

Couplings - Customer Supplied

These lists are not all inclusive, all options may not be available for all motor types / frames.

X

X

Connections

Note:

X

X

Conduit Box - Main and Auxiliary

•CASE D–TBD (To be determined) Special engineered product

Insulation Leads

Assembly - Mounting

Breather Drain - Plugs

Precision balance Seal lead Screen Siemens standard paint for high corrosive environment Special color paint Special shaft extension

6-2 6-2

X

X

Modifications/Accessories

X

X

Bearings

•CASE A1–12 WEEKS DELIVERY Class H insulation Double or triple dip & bake Fungus proof/tropicalization Inverter Duty motor Space heater Special ambient (from -40°C to +70°C) Special frequency Special voltage (<600V) Thermistor (standard) Thermostat (standard) Up-frame Winding RTD (standard) Y/D connection Terminal strip TEAO enclosure Additional plate Alemites/grease relief Bronze fan Auxiliary condulet Breather/drain C or D flange CE provision/marking Dowel pin hole Export packing/boxing Fabricated conduit box Group C Inpro/Seal® bearing isolator Jack screw provision Oil mist provision Oil mist ready Oversized conduit box

DP RG X

X

Bases

All custom accessory lead times are based on “custom build” motors only, please refer to modification section on front for standard stock modification lead times.

SD X

Ambient Balance

Dimensions

Motor Type

Modifications/Accessories GPA GP X X

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

CONTENTS

Example #1: 75HP, 1800RPM, 230/460V, 365T, RGZPSD, horizontal foot mounted with C-flange and space heaters. Base List Price

$6,033

C-Face

$309

Order Code RG01

Space Heaters

$262

Order Code A40

Total List Price:

$6,604

Delivery:

Part Number 1LA03654SP21

5 Working Days, subject to availability

Example #2: 10HP, 1800RPM, 208-230/460V, 215T, GP10A, D-flange with feet, thermostats and bi-directional rotation arrow. Base List Price

$649

Part Number 1LE21012AB214AA3

D-Flange with Feet

$152

Position 14 in Part Number changes to F

Thermostats

$150

Position 15 in Part Number changes to G

Rotation Arrow

$40

Total List Price:

$991

Delivery:

Order Code K70 (add a -Z to the end of the part number plus the order code) New Part Number - 1LE21012AB214FG3-Z +K70

5 Working Days, subject to availability

2007 Low Voltage AC Motors Selection and Pricing Guide

6-1

INVERTER Duty Severe Duty

ALTITUDE

ASSEMBLY (continued)

TEFC (General Purpose & Severe Duty) motors with a 1.15 service factor in a 40°C ambient at 3300 feet will operate at a 1.0 service factor in a 40°C ambient at altitudes up to 9900 feet. For altitudes greater than 9900 feet, please consult factory. Standard motors will operate at their rated service factor at altitudes above 3300 feet at the corresponding ambient temperatures as shown in the following table.

6600

30

9900

20

FLOOR MOUNTINGS

ASSEMBLY F-1

mounting, bearing brackets are assembled and

ASSEMBLY F-2*

1

Mounting - C-2

70

5

RG42

Mounting - F-2

70

5

Mounting - W-6

70

5

is made to locate fittings on any particular side of the ASSEMBLY W-2

ASSEMBLY W-3

List Price Adder $ 70

Lead Time (days) 5

2

Mounting - F-2

70

5

RG43

4

Mounting - W-6

70

5

RG44

Mounting - W-7

70

5

5

RG45

Mounting - W-5

70

5

Mounting - W-8

70

5

Mounting - W-7

70

Mounting - W-5

70

5

RG46

7

Mounting - W-8

70

5

RG47

Mounting - C-1

70

5

8

Mounting - C-1

70

5

RG48

Mounting - W-1

70

5

9

+Order Code RNA

RG49

Mounting - W-2

70

5

Mounting - W-1

5

RG50

Mounting - W-3

70

5

5

RG51

Mounting - W-4

70

5

70

Mounting - W-2

70

R3A

Mounting - W-3

70

5

R4A

Mounting - W-4

70

5

BALANCE

ASSEMBLY W-4

TABLE 1 BALANCE LIMITS MAXIMUM AMPLITUDE, INCHES, PEAK TO PEAK Balance

NEMA Standard

Precision

Extra Precision Frame

hazardous duty motors

RPM (synchronous) ASSEMBLY W-6**

ASSEMBLY W-7**

ASSEMBLY W-8**

CEILING MOUNTINGS

ASSEMBLY C-2

Assembly F-1, W-2, W-3, W-6, W-8 and C-2 = Standard Lead Location Assembly F-2, W-1, W-4, W-5, W-7 and C-1 = Lead Location Opposite Standard

0-999 1000-1999 1500-2999 3000-4000

143T 449T IN P-P .0025 .0025 .0025 .0025

143T 326T IN P-P .0005 .0005 .0005 .0005

364T 449T IN P-P .00075 .00075 .00075 .00075

143T 256T IN P-P .0002 .0002 .0002 .0002

284T 326T IN P-P .0003 .0003 .0003 .0003

364T 449T IN P-P .0004 .0004 .0004 .0004

NOTE: IN P-P refers to amplitude displacement. NEMA unfiltered velocity limit 0.15 in/s peak. IEEE Std 841 unfiltered velocity limit 0.08 in/s peak. Apply the list price additions as shown in Table 2 below to the basic modified motor list price. NOTE: For balance limits greater that Precision balance, contact factory.

TABLE 2 LIST PRICE ADDITION FOR SPECIAL BALANCE LIMITS List Price Adder $ Frame Size

Order Code

Balance Limit

M69 M70

Precision* Extra Precision*

182 184 128 216

213 215 128 216

254 256 147 228

284 286 147 228

324 326 167 260

364 365 167 260

404 405 211 350

444 445 211 350

447 449 404 450

Lead Time (days) 60 60

* Not available for DP (140-360 frame) motors.

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

6-3

Dimensions

ASSEMBLY W-5**

ASSEMBLY C-1

6-2

Typical Performance

the motor in the position shown. However, no attempt ASSEMBLY W-1

Modification Mounting - C-2

All motors are dynamically balanced to commercial limits measured in accordance with NEMA MG1-12.06. Modified motors can be built to exceed standard commercial limits based on Table 1 below.

WALL MOUNTINGS

* F-2 assembly not available as modification for Dimensions

5

Modification

* Applicable to GP10A & GP100A motors only. Part Number Position 16 - 1XX2 XXX When ordering any of the above modifications, Position 16 in the Part Number must change to the corresponding code.

grease fittings are properly installed for operation with

CAUTION

70

R2A

Motors can be furnished in assemblies shown. Modifications will be of F-1 assembly stock motors.

** Horizontal ball bearing motors assembly W-5, W-6,W-7 and W-8 are not suitable for external thrust in excess of the weight of the rotor and half-coupling.

Mounting - F-3 ( top mounted) *

R1A

ASSEMBLY - Mounting & Terminal Box Position

motor.

0

6

TEFC (General Purpose & Severe Duty) motors with a 1.15 service factor in a 40°C ambient at 3300 feet will operate at a 1.0 service factor at 3300 feet altitude up to a 65°C ambient. For ambients greater than 65°C or below -25°C, please consult factory.

Lead Time (days)

Order Code RG41

5

AMBIENT

List Price Adder $

Modifications Accessories

Modifications Accessories

Ambient Temperature (°C) 40

When motors are ordered according to a particular Typical Performance

Position 16 Code

Lead Time

Lead Time

Maximum Altitude (feet) 3300

For Motor Types RG...

For Motor Types GPA, GP, SD & DP (400+ frames only)

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Modifications/Accessories

INVERTER Duty Severe Duty

Modifications/Accessories

INVERTER Duty Severe Duty

Modifications/Accessories

BASES

BREATHERS AND DRAIN PLUGS (Horizontal mounted motors only)

Part Number

Double Adjustment Slide

143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T 404T 405T 444T 445T 447T 449T

List Price Adder $

Lead Time (Days)

83 83 83 83 93 93 170 170 190 190 250 250 290 290 585 585 650 650 870 870

5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5

L45

Frame Size

Code

Modification

445 447 449 S449

(days)

110 110 110 160 160 160 210 210 210

210 210 210 210

2

240 240 240 240

2

Breather & Drain - T-Drain, (SS) for TEFC, General Purpose and Severe Duty motors

L46

Lead Time

140 180 210 250 280 320 360 400 444

Breather & Drain - UL Approved, Class I, Group D, Class II, Groups F,G hazardous areas.

-

-

-

-

240 240 240 240 240

CONDUIT BOX - MAIN List Price Adder $ Order

Frame Size

Code

Modification

Lead Time

140 180 210 250 280 320 360 400 444

L01

Cast Iron Instead of Cast Aluminum or Steel*

115 120 125 130 140 155 170 195

J84

Conduit Box Turned 90° CCW

70

70

70

70

70

70

70

J85

Conduit Box Turned 180° CCW

70

70

70

70

70

70

J86

Conduit Box Turned 270° CCW

70

70

70

70

70

70

445 447 449 S449

(days)

-

-

-

-

-

5

70

70

70

70

70

70

5

70

70

70

70

70

70

70

5

70

70

70

70

70

70

70

5

* Applicable only to GP (cast iron) motors and DP (140-400 fame) motors.

CONDUIT BOX - AUXILIARY

Modifications Accessories

CP-839-481-120 CP-839-481-121 CP-839-481-122 CP-839-481-123 CP-839-481-124 CP-839-481-125 CP-839-481-156 CP-839-481-157 CP-839-481-158 CP-839-481-159 CP-839-481-160 CP-839-481-161 CP-839-481-132 CP-839-481-133 CP-839-481-149 CP-839-481-150 CP-839-481-151 CP-839-481-152 CP-839-481-153 CP-839-481-155

Frame

Lead Time

Lead Time

Single Adjustment Slide

Modifications Accessories

List Price Adder $ Order

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

SLIDE BASES — shipped loose Base Description

INVERTER Duty Severe Duty

Modifications/Accessories

Order Code Device For Aux. Conduit Box PTC KTY84 Space Thermistors Thermo Temperature Heaters stats Sensors

Base Description

List Price Lead Time Adder $ (days) CP-839-481-101 Bases-Adapter (old:182U-184U new:143T-145T) 168 5 CP-839-481-102 Bases-Adapter (old:213U-215U new:182T-184T) 168 5 CP-839-481-103 Bases-Adapter (old:254U-256U new:213T-215T) 168 5 CP-839-481-104 Bases-Adapter (old:284U-286U new:254T-256T) 168 5 CP-839-481-105 Bases-Adapter (old:324S new:284TS) 192 5 CP-839-481-106 Bases-Adapter (old:324S-326S new:284TS-286TS) 192 5 CP-839-481-107 Bases-Adapter (old:324U-326U new:284T-286T) 192 5 CP-839-481-110 Bases-Adapter (old:364U-365U new:324T-326T) 224 5 CP-839-481-108 Bases-Adapter (old:364US-365US new:324TS) 224 5 CP-839-481-109 Bases-Adapter (old:365US new:326TS) 224 5 CP-839-481-111 Bases-Adapter (old:404U-405U new:364T-365T) 304 5 CP-839-481-112 Bases-Adapter (old:404US-405US new:364TS-365TS) 304 5 CP-839-481-116 Bases-Adapter (old:444U-445U new:364T-365T) 368 5 CP-839-481-113 Bases-Adapter (old:444U-445U new:404T-405T) 304 5 CP-839-481-115 Bases-Adapter (old:444US-445US new:364T-365T) 368 5 CP-839-481-117 Bases-Adapter (old:444US-445US new:364TS-365TS) 368 5 CP-839-481-114 Bases-Adapter (old:444US-445US new:404TS-405TS) 304 5

J00

J10

J20

J50

Modification

Condulet - Main Box side*

List Price Adder $ Frame Size Lead Time 140 180 210 250 280 320 360 400 444 445 447 449 S449 (days) na

J02

J12

J22

J52

Condulet to Main Box*

J03

J13

J23

J53

Auxiliary Box to Main Box* na

J04

J14

J24

J54

na

na

na 165 165 165 165 165 165 165 165 165

165 165 165 165 165 165 165 165 165 165 165 165 165 na

na

*** ***

na 291 291 291 291 291 291 291 291 291

***

165 165 165 165 165 165 165 165 165 165 165 165 165

***

165 165 165 165 291 291 291 291 291 291 291 291 291

***

Condulet - Opposite of Main Box** Auxiliary Box - Opposite J05

J15

J25

J55

of Main Box*

J06

J16

J26

J56

Explosion-Proof Condulet Opposite of Main Box* na

na

na

na 400 400 400 400 400 400 400 400 400

***

* Not available for the GPA and DP motors. ** Not available for the GPA and DP (140-360 frame) motors. *** Lead time corresponds with the protective device's lead time.

*If Special adapter base is required, refer to Factory for price and shipment.

BEARINGS List Price Adder $ Order Code

Frame Size Options

Lead Time

140 180 210 250 280 320 360 400 444

L65

Roller Instead of Ball ***

-

L66

Bearings - Insulated **

-

765 1050 1315 1665 1975 2350 5100 7850 7850 7850 7850

L67

Bearings - Insulated - ODE Only **

-

385 525 660 835 990 1175 2550 3925 3925 3925 3925 5530

L68

Bearings - Sealed Ball (except 2 Pole, 360+ Fr)*

6-4

-

-

-

825 825 825 825

std

445 447 449 S449

160 160 160 320 320 320 400 640 640

2007 Low Voltage AC Motors Selection and Pricing Guide

std

std

std

(days)

std

60

-

70

640 640 640 800

70 20

* Not available on IEEE 841 motors. ** Only available as sealed bearings. Not available for hazardous duty motors. *** Not available for RGZP motors. Motors having roller bearings (444T to 449T) require a minimum radial load. Use of these motors in direct connected applications is discouraged to avoid excessive drive end bearing noise and/or reduced bearing life.

2007 Low Voltage AC Motors Selection and Pricing Guide

6-5

Dimensions

Dimensions

Part Number

Typical Performance

Typical Performance

ADAPTER BASES (RG Motors Only) - shipped loose

INVERTER Duty Severe Duty

Modifications/Accessories

CONNECTIONS

DRIP COVER

Part Winding Start - Starting torques are reduced at the motor shaft. Wye Start - Delta Run - Starting torques are reduced at the motor shaft.

Order

INVERTER Duty Severe Duty

Modifications/Accessories

For Motor Types GP, SD & DP (400 frames only) List Price Adder $ Positions

213 254 404 444 447

Time

145 184

215 256 405 445 449

(Days)

Part Winding Start - 200V, 60Hz

na

na

na

na 290 482 506

60

21

Part Winding Start - 230V, 60Hz

na

na

na

na 290 482 506

60

22

Part Winding Start - 460V, 60Hz

na

na

na

na 290 482 506

60

23

Part Winding Start - 575V, 60Hz

na

na

na

na 290 482 506

60

24

Part Winding Start - 230/460V, 60Hz

na

na

na

na 290 482 506

60

30

Wye Start - Delta Run - 200V, 60Hz

104 104

104 104 290 482 506

60

31

Wye Start - Delta Run - 230V, 60Hz

104 104

104 104 290 482 506

60

32

Wye Start - Delta Run - 460V, 60Hz

104 104

104 104 290 482 506

60

33

Wye Start - Delta Run - 575V, 60Hz

104 104

104 104 290 482 506

60

ENCODERS Encoder Selection Guide Encoders (also known as tachometers) mount on the motor shaft to provide precise speed and position feedback to the control system. Encoders use two basic technologies: Magnetic/Magnetoresistive, and Optical, and two common mounting methods: hollow shaft and modular. Encoder selection should be based on several factors: mechanical service duty, and environment. Type

Converting

Films

Paper

Hoist

Steel

Marine

Oil Drilling

Light

143 145 na na na na na 104 104 104 104

182 184 na na na na na 104 104 104 104

213 215 na na na na na 104 104 104 104

List Price Adder $ Frame Size 254 284 324 364 256 286 326 365 na 104 126 185 na 104 126 185 na 104 126 185 na 104 126 185 na 104 126 185 104 104 126 185 104 104 126 185 104 104 126 185 104 104 126 185

Standard 404 405 290 290 290 290 290 290 290 290 290

444 445 482 482 482 482 482 482 482 482 482

447 449 506 506 506 506 506 506 506 506 506

Lead Time (days) 60 60 60 60 60 60 60 60 60

Heavy (Darker=better suited for application)

Order Codes Single Output

Dual Output

Marker Pulse

Shaft Grounding

Lead Time (days)

Avtron M3 1024 PPR

G00

Y75

Std

Y75

75

Avtron M4 1024 PPR

G01

Y75

Std

Y75

75

Avtron M56 1024 PPR

G02

Y75

Std

Y75

75

Avtron M85 1024 PPR

G03

Y75

Std

Y75

75

BEI HS35 1024 PPR

G04

NA

Std

Y75

75

Dynapar HS35 1024 PPR

G05

NA

Std

Y75

75

Northstar 8500 1024 PPR (210-360)

G06

Y75

Y75

Y75

75

COUPLINGS - Customer Supplied

Northstar 8500 1024 PPR (400-440)

G07

Y75

Y75

Y75

75

Rigid couplings, flexible couplings, pinions and V-belt sheaves can be pressed on at List Price adders per the table below. Couplings, pinions or sheaves must be finish bored and key seated to Siemens shaft dimensions and must be shipped to the plant freight prepaid. List Price Adder $

Northstar SL56 1024 PPR

G08

Y75

Y75

Y75

75

Avtron HS35A

G09

NA

Std

Y75

75

Avtron M6 1024 PPR

G10

Y75

Y75

NA

75

Order

Frame Size

Lead Time

Code

140

180 210 250 280 320 360 400 444

445

447 449 S449

H10

325

325 325 325 325

480

480 480

325 480 480 480

480

Accessory

Dimensions

Dimensions

Part Winding Start - 200V, 60Hz Part Winding Start - 230V, 60Hz Part Winding Start - 460V, 60Hz Part Winding Start - 575V, 60Hz Part Winding Start - 230/460V, 60Hz Wye Start - Delta Run - 200V, 60Hz Wye Start - Delta Run - 230V, 60Hz Wye Start - Delta Run - 460V, 60Hz Wye Start - Delta Run - 575V, 60Hz

Typical Applications Conveying

Please see the following table for the list prices adders.

(days) 5*

* After receipt of the coupling, sheave, etc.

6-6

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

Typical Performance

Typical Performance

For Motor Types RG & DP (440 frames only)

RG10 RG11 RG12 RG13 RG14 RG15 RG16 RG17 RG18

5

technologies, such as solid shaft coupled, are available and may be required for special applications, but are not generally recommended. Call Factory for pricing. Encoder Wiring: Encoders may be connected via military connectors (solder connections with screw housing) or industrial connectors (pin connections with terminal strip). Vendor standard connectors shown; call factory for special connectors.

Type of Encoder: Optical encoders are usually less expensive, but are more vulnerable to shock, vibration, and contamination from dusty, dirty, wet, or chemical environments; Siemens recommends magnetic encoders for these environments. Encoder Mounting: Hollow shaft/tethered encoders are easier to mount, but are less robust than modular encoders; Siemens recommends modular encoders for rough mechanical service applications. Other mounting

Recommended

Part Number Positions 12 & 13 - 1XX2 XXX * When ordering any of the above modifications, Positions 12&13 in the Part Number must change to the corresponding code.

Connection Type

(days)

106 106 106 114 114 204 414 580 1072 1072 1072 1072 1072

Lead

143 182

20

Order Code

Drip Cover*

445 447 449 S449

Modifications Accessories

Modifications Accessories

Connection Type

K33

Lead Time

140 180 210 250 280 320 360 400 444

Lead Time

Lead Time

Codes

Modification

* Vertical lifting devices are not included.

Frame Size

12 & 13

Frame Size

Code

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

List Price Adder $

6-7

INVERTER Duty Severe Duty

Modifications/Accessories EXPORT PACKAGING List Price Adder $

Encoders can be factory installed at Siemens for RGZESDI and RGZZESDI motors only. Unless specified, all encoders have 1024 PPR; other PPR & special voltage output ranges available upon request. NEMA Frame

Model

Mill Duty

Encoder Style

List Price Adder $

Optional List Price Adder $

Connector Output Figure Style (VDC) Single Output Dual Output Marker Pulse Shaft Grounding

Lead Time Modifications Accessories

213-365

Standard Optical Hollow Shaft Heavy

Magnetic Modular

1741 1298

2529 1911

Std Std

420 **

Industrial Industrial

5-24 5-24

List Price Adder $

C

Order Modification

140 180 210 250 280 320

360

400

444-445

447-449

(days)

Fans - Bronze

418 418 540 575 720 870

910

1014

1400

1400

60

Avtron HS35A Light

Optical Hollow Shaft

875

NA

Std

**

Military

5-24

E

Code

BEI HS35

Light

Optical Hollow Shaft

1246

NA

Std

**

Military

5-24

E

M10

Dynapar HS35 Light

Optical Hollow Shaft

Northstar SL56 Heavy

Magnetic Modular

900

NA

Std

**

Military

5-24

E

1400

2550

66

**

Industrial

5-15

C

Avtron M3

Standard Optical Hollow Shaft

1741

2529

Std

420

Industrial

5-24

E

Avtron M85

Heavy

1529

2253

Std

**

Industrial

5-24

C

Magnetic Modular

Frame Size

For Motor Types GPA, GP & SD List Price Adder $ Frame Size

Optical Hollow Shaft

875

NA

Std

**

Military

5-24

E

BEI HS35

Optical Hollow Shaft

1246

NA

Std

**

Military

5-24

E

Position 14 Code E

C-Face with Feet

Light

Dynapar HS35 Light

Optical Hollow Shaft

Northstar 8500 Heavy

Magnetic Modular

900

NA

Std

**

Military

5-24

E

4380

5381

327

972

Industrial

5-15

F

Avtron M4

Heavy

Magnetic Hollow Shaft

2346

3380

Std

458

Industrial

5-24

E

Avtron M85

Heavy

Magnetic Modular

2574

3002

Std

**

Industrial

5-24

C

BEI HS35

Light

Optical Hollow Shaft

1246

NA

Std

**

Military

5-24

E

Dynapar HS35 Light

Optical Hollow Shaft

900

NA

Std

**

Military

5-24

E

Northstar 8500 Heavy

Magnetic Modular

5140

6441

327

972

Industrial

5-15

D

Modification

140 180

Lead Time (Days)

210 250

53

76

76

99

2

67

99

99 134

G

C-Face without Feet

N

C-Face with Feet and Drip Cover

159 159 159 213

60** 2

L

C-Face without Feet and with Drip Cover*

159 159 159 213

60**

F

D-Flange with Feet

106 152 152 198

2

H

D-Flange without Feet

134 198 198 268

60**

P

D-Flange with Feet and Drip Cover

379 469 469 613

2

M

D-Flange without Feet and with Drip Cover*

379 469 469 613

60**

1646

2260

Std

**

Industrial

5-24

B

Avtron HS35A Light

Optical Hollow Shaft

1245

NA

Std

**

Military

5-24

B

For Motor Types DP (140-400 stock frames only)

BEI HS35

Optical Hollow Shaft

1616

NA

Std

**

Military

5-24

B

Heavy

Magnetic Hollow Shaft

2503

3451

Std

420

Industrial

5-24

B

Avtron M56

Heavy Light

Northstar SL56 Heavy

Optical Hollow Shaft Magnetic Modular

1270 1734

NA 2884

Std 66

** **

Military Industrial

5-24 5-15

B B

Avtron M4

Heavy

Magnetic Hollow Shaft

2731

3765

Std

458

Industrial

5-24

B

Avtron M85

Heavy

Magnetic Modular

2196

2657

Std

**

Industrial

5-24

B

BEI HS35

Light

Optical Hollow Shaft

1616

NA

Std

**

Military

5-24

B

Northstar 8500 Heavy

Magnetic Modular

4767

5381

327

973

Industrial

5-15

B

Dynapar HS35 Light

Optical Hollow Shaft

1270

NA

Std

**

Military

5-24

B

284-365 Avtron HS35A Light Northstar SL56 Heavy Avtron M4 Heavy 324-365 400- Avtron M85 Heavy S449 Northstar 8500 Heavy Explosion-Proof Applications 143Avtron M6 Heavy S449

List Price Adder $ Position 14 Code E

Frame Size

Lead Time

Modification

140

180

210

250

280

320

360

400

(days)

C-Face with Feet

53

76

76

99

140

216

309

478

2

Part Number Position 14 - 1XX2 XXX * When ordering any of the above modifications, Position 14 in the Part Number must change to the corresponding code.

For Motor Types RG & DP (440 frames only) List Price Adder $

Optical Hollow Shaft

1245

NA

Std

**

Military

5-24

B

Order

Magnetic Modular

1734

2884

66

**

Industrial

5-15

B

Magnetic Hollow Shaft

2348

3382

Std

458

Industrial

5-24

B

Code RG01

Modification C-Face with Feet

Magnetic Modular

2340

3002

Std

**

Industrial

5-24

B

RG02

Magnetic Modular

5140

6441

327

973

Industrial

5-15

B

Magnetic Hollow Shaft

4749

6362

146

NA

Box w/term

5-24

**Consult factory for pricing

Dimensions

Magnetic Modular

Part Number Position 14 - 1XX2 XXX When ordering any of the above modifications, Position 14 in the Part Number must change to the corresponding code. * Includes vertical lifting devices. ** Custom build if stocked round body motors are not available for modification. Please consult with factory.

Avtron M4

Lead Time

FLANGED HOUSINGS/END SHIELDS

Avtron HS35A Light

Dynapar HS35 Light

284-286

5

Consult Factory

E

TEBC Motors

254-256

225 510 760 1010

Special

Typical Performance

400S449

Sea Freight

B10

Modifications Accessories

Typical Performance

143-184

Modification

Lead Time (Days)

Frame Size

Lead Time (days)

140 53

180 76

210 76

250 99

280 140

320 216

360 309

400 444-445 447-449 S449 478 598 605 1500

C-Face without Feet

67

99

99

134

213

306

553

826

1016

1250

na

RG03

C-Face with Feet and Drip Cover

159

159

159

213

318

420

723

1058

1670

1670

2565

2

RG04

C-Face without Feet and with Drip Cover*

159

159

159

213

318

420

723

1058

1670

1670

na

60**

RG05

D-Flange with Feet

106

152

152

198

280

432

618

956

1196

1210

2800

2

RG06

D-Flange without Feet

134

198

198

268

426

612

1106 1652

2032

2500

na

60**

RG07

D-Flange with Feet and Drip Cover

379

469

469

613

738

1070 1503 2018

2710

2920

4510

2

RG08

D-Flange without Feet and with Drip Cover*

379

469

469

613

738

1070 1503 2018

2710

2920

na

60**

2 60**

* Includes vertical lifting devices. ** Custom build if stocked round body motors are not available for modification. Please consult with factory. Custom build 400 frames are available for DP motors. D-Flanges are not available for 140-250 frame RGZP and RGZZESD (hazardous duty) motors.

6-8

2007 Low Voltage AC Motors Selection and Pricing Guide

Lead Time

Avtron M56

B09

Frame Size 140 320 400 250 280 360 440

FANS

TEFC Motors Avtron M3

Order Code

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

ENCODERS (continued)

Dimensions

INVERTER Duty Severe Duty

Modifications/Accessories

2007 Low Voltage AC Motors Selection and Pricing Guide

6-9

INVERTER Duty Severe Duty

Modifications/Accessories LEADS/TERMINAL BLOCKS List Price Adder $

Order

List Price Adder $

Frame Size

Code

Modification

L27

Provision For Grounding (Tapped Hole on

140 180 210 250 280 320

360

400 444-445

95

125

125

95

95

110 110 125

175

447-449 S449 175

175

Lead Time

Order

(days)

Code

5

Frame with bolt) A clamp type terminal is provided as standard inside the motor conduit box.

Order

Lead Time

Modification

140 180 210 250 280 320

360

400 444-445

L22

Stainless Steel Hardware *

134 134 134 134 134 165

203

250

308

379

425

5

L20

Lifting Eyebolt

30

-

-

-

-

-

2

30

-

-

-

-

447-449 S449

(days)

* Stainless steel hardware, limited to bearing housing bolts, terminal housing bolts, fan bolts and breather drains only, is available on modifiable general purpose and severe duty motors. This option is not available on hazardous duty motors.

444-445

447-449

115

115

115

K80

Burndy Hydent type YA

115 115 115 115 115 115

115

K83

Terminal Block - 3 lead only*

150 150 150 225 225 330

330

K89

Sealed Leads**

146 146 146 189 314 405

510

Y85

Leads, Special Cable Length*

(days) 5 10

708

961

1528

5

Consult Factory

60

HAZARDOUS DUTY MOTORS Class I: Gr. B

Hydrogen (not available)

Gr. C

Atmospheres containing ethyl and ether vapor

Gr. D

Atmospheres containing gasoline, petroleum,

Frame Size

Code

Modification

Gr. E

Atmospheres containing metal dust

Gr. F

Atmospheres containing carbon black, coal or coke

Gr. G

Atmospheres containing grain dust.

dust.

List Price Adder $ Frame Size

Lead Time

140

180 210 250 280

320

360

400

444-445

447-449

(days)

470

470 685 699 769

923 1077

1230

1600

1662

70

512

512 727 743 828

995 1164

1332

1687

1788

5

Class I, Gr. D Class B 1.0SF

380

380

650

1100

1100

1350

20

L55

Oil Mist Ready *

300 300 300 350

380

380

650

1100

1100

1350

20

L57

Special Grease (High & Low Temp) (Mobil 28)

325 600 600 600

600

825

825

1100

1100

1100

20

L58

Special Grease (Mobilith SHC 100)

225 225 225 225

225

425

425

425

425

425

20

L60

Grease Fitting - Pressure Relief

30

30

30

30

30

30

2

THE NATIONAL ELECTRICAL CODE

INSULATION

2002-501.8(B) FOR MOTORS Frame Size

Moisture/Powerhouse (extra dip & bake) *

C07

Fungus Protection

C08

Tropicalization Moisture (extra Dip & bake, fungus spray)*

30

30

30

30

140 180 210 250 280 320

IN CLASS I, DIVISION 2 AREAS.

(days)

NATIONAL ELECTRICAL CODE

41

41

41

52

87

146 146 146 189 314

1234

60

111

137

184

239

294

294

2

405

510

708

961

1528

1528

60

8

900

750

For hazardous duty motors, contact factory. For standard 50 hertz voltages, see Voltage section.

Nameplate Change (Rerate/Derate)**

110

2

Provide Extra Nameplate

110

2

REQUIREMENTS AND

1234

1000

Y82

60 75

722

1500

1200

Y80

1573 3600

524

1800

6

MUST BE OBSERVED.

1573 2500

373

4

Division 2 *

606 2500

294

Speed (RPM) 50 Hertz 3000

M22

425

105 105 105 137 227

2

60 Hertz 3600

RESTRICTIONS

294

230

No. of Poles

Modification Auxiliary Nameplate

1120 1120 1120 1120 1440 1440 1820 2300

82 105 175

above for nameplate change. Motor type RGZZESD (Class I, Groups C & D, Division 1) with 1.0 service factor can be re-nameplated to RGZZESD (Class I, Group C, Division 1) with 1.15 service factor for 140-250 frame motors only. Use Order Code Y80 above for nameplate change.

Order Code M21

400 444-445

82

447-449 S449

Lead Time

360

82

The following tabulation shows the synchronous speeds for 60 and 50 hertz. For different frequencies or adjustable frequency applications, contact factory. To derate a continuous duty 60 hertz motor to a continuous 50 hertz motor, use the modifiable list price of the next larger HP 60 hertz motor and add the list price as shown in the above table. Motor will be Class F, 1.15 service factor. Service Factor Change (rerate) Motor type RGZZESD (Class I, Group D, Class II, Groups F & G, Division 1) with 1.0 service factor can be re-nameplated to RGZZESD (Class I, Group D, Division 1) with 1.15 service factor for 140-250 frame motors only. Use Order Code Y80

PERMITTED TO BE INSTALLED

List Price Adder $ Order

C04

(days)

300 300 300 350

OPERATION, THE DEFINITION IN

motors,RGZEAD (automotive duty) motors and RGZTESD (Design C) motors.

Vacuum Pressure Impregnation (VPI) *

447-449

Provisions for Oil Mist *

MOTOR MEETS, DURING NORMAL

List price adders are only for custom built hazardous duty motor list prices for RGZESD (Multi-Speed)

Class H *

444-445

51518308001

List Price Adder $ 110

Lead Time (days) 2

205

2

* Not available on GPA & DP motors. ** Not available on DP (140-360 frame) motors.

* Not available for DP motors.

6-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

6-11

Dimensions

pricing symbol assigned to the enclosed motor base price.

C01

400

L54

Division 2 Non hazardous duty motors can be used in Class I and Class II Division 2 areas provided no arcing devices are used. Advise ignition temperature or T-code and Class with requests. ODP motors not available for application in Division 1 or Division 2 areas. Non (agency) certified, general purpose and severe duty motors are available with the following metal tag: Frequency Change (derate)

additions to the non-hazardous duty motor of the rating required; use the

C00

360

NAMEPLATES

For unlisted hazardous duty motors, add the following price

Modification

Lead Time

140 180 210 250 280 320

Typical Performance

Class II:

Class II, Gr. E

Order

Provisions for Oil Mist - Convert a motor built with grease lubricated bearings to one that can be converted to oil-mist lubricated bearings at a future date. Siemens does not supply the oil mist system, reclassifer orifice, details of flow rate or oil-air ratios. Such information must be obtained from the oil-mist vendor.Oil Mist Ready - Convert a motor built with grease lubricated bearings to oil mist lubricated bearings for immediate use. Siemens does not supply the oil mist system, reclassifer orifice, details of flow rate or oil-air ratios. Such information must be obtained from the oil-mist vendor.

and natural gas.

Class II, Gr. F & G

List Price Adder $

* Available on horizontal Severe Duty motors only.

naphtha, alcohols, acetone lacquer solvent vapors

Modification

LUBRICATION

Modifications Accessories

Modifications Accessories

400

** Not available for all DP motors.

Frame Size

Code

Typical Performance

™

Lead Time

360

* Not available for DP (140-360 frame) motors.

List Price Adder $

Code

140 180 210 250 280 320

Lead Time

Lead Time

HARDWARE

Frame Size Modification

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

GROUNDING

Dimensions

INVERTER Duty Severe Duty

Modifications/Accessories

INVERTER Duty Severe Duty

Modifications/Accessories PROTECTIVE DEVICES (continued)

List Price Adder $ Order Code N01

Frame Modification

140-280

WINDING PROTECTION - For Motor Types RG & DP (440 frames & custom build 400 frames)

Lead Time

320-440

List Price Adder $

(days)

Paint - 2 Part Epoxy with surface preparation

Order

(Carboline or Ameron)

60

Code

RG20 PTC thermistors, 3 embedded temperature

3750

3750

N03

Standard Primer Only

385

510

60

Y60

Standard Paint, Special Color

385

510

60

Y61

Special Paint, Special Color

Frame Size Modification

360

400

444-445

447-449

(days)

425 425 425 425 425 425

425

425

425

425

60

850 850 850 850 850 850

850

850

850

850

60

425 425 425 425 425 425

425

425

425

425

60

850 850 850 850 850 850

850

850

850

850

60 60

sensors for tripping * RG21 PTC thermistors, 6 embedded temperature

Consult Factory

RG22 PTC thermistors, 3 embedded temperature sensors for tripping, drive operation *

Siemens standard finish paint consists of the following:

RG23 PTC thermistors, 6 embedded temperature

Epoxy modified acrylic air dry enamel.

Lead Time

sensors for alarm and tripping *

Note: Order codes N01, N03, Y60 & Y61 are not available for DP (140-360 frame) motors.

sensors for alarm and tripping, drive operation *

Viscosity: 28-30 seconds No.2 Zahn cup @ 77°F Fineness: 7 N.S. units Hegeman gage

RG24 KTY84-130, 2 embedded temperature sensors *

658 658 658 658 658 658

658

658

658

658

Adhesion: 90% Cross-hatch test (tape)

RG25 Thermostats, normally closed, 2 per motor

150 150 150 150 150 200

200

300

300

370

5

Impact resistance: 40 inch pounds direct - No cracks

RG27 Thermocouples, coil head **

na

na

na

na

na

na

1186 1186

1186

1186

60

Composition: Lead and Chromate free

RG28 Winding temperature protection, Stator

na

na

na

na

na

na

1996 1996

1996

1996

60

RTD's (coil head, 3 per phase), 100Ω

Color: GPA, GP, SD & DP Motors - RAL 9023 gray RG… Motors - RAL 5001 blue

Platinum, complete with auxiliary box with

Modifications Accessories

Modifications Accessories

Lead Time

140 180 210 250 280 320

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

PAINT

Lead Time

INVERTER Duty Severe Duty

Modifications/Accessories

terminal strip opposite to main box **

WINDING PROTECTION - For Motor Types GP, SD & DP (140-400 stock frames - Code G only) List Price Adder $ Order

Frame Size

Code Modification

Lead Time

140 180 210 250 280 320 360

400

(days)

* Control Modules are available for thermistors. Order Code A90. Add $450 List. 35 day lead-time. Shipped loose for customer installation. ** Price does not include temperature readout devices. Not available for 360 frame ODP motors. Contact factory for other resistance values. ** Price does not include temperature readout devices. Contact factory for other resistance values. Notes: • Thermistors - leads marked PM1 & PM2 • Thermostats - leads marked P1 & P2

425 425 425 425

na

na

na

na

60

BEARING PROTECTION

PTC thermistors, 6 embedded temperature sensors for alarm and tripping*

850 850 850 850

na

na

na

na

60

Order

D

PTC thermistors, 3 embedded temperature sensors for tripping, drive operation*

425 425 425 425

na

na

na

na

60

E

PTC thermistors, 6 embedded temperature

850 850 850 850

na

na

na

na

60

B

PTC thermistors, 3 embedded temperature

List Price Adder $ Frame Size

Code A51

Modification

140 180 210 250 280 320

400

444-445

447-449

(days)

na

2200

2200

2200

70

Bearing thermal protection, Bearing RTDs with with connection head and terminal block -

sensors for alarm and tripping, drive operation*

Lead Time

360

na

na

na

na

na

na

100Ω Platinum ** ** Price does not include temperature readout devices. Contact factory for other resistance values.

F

KTY84-130, 2 embedded temperature sensors*

658 658 658 658

G

Thermostats, normally closed, 2 per motor

150 150 150 150 150 200 200

na

na

na

na

60

300

5

Part Number Position 15 - 1XX2 XXX When ordering any of the above modifications, Position 15 in the Part Number must change to the corresponding code. * Control Modules are available for thermistors. Order Code A90. Add $450 List. 60 day lead-time. Shipped loose for customer installation. ** Price does not include temperature readout devices. Contact factory for other resistance values. Notes: • Thermistors - leads marked PM1 & PM2 • Thermostats - leads marked P1 & P2

SERVICE FACTOR

ROTATIONAL ARROWS Order Code K70

List Price Adder $ 40

Modification Bidirectional

K71

Clockwise

40

2

K72

Counterclockwise

40

2

For non-standard service factor, contact factory. Refer to Nameplates for rerating RGZZESD (hazardous duty) motors from the standard 1.0 service factor to a 1.15 service factor.

Lead Time (days) 2

SHAFTS List Price Adder $ Order Code

Frame Size Modification

M57 Carbon Steel (C4140)

6-12

2007 Low Voltage AC Motors Selection and Pricing Guide

140 180 210 250 280 320 -

-

-

-

-

-

Lead Time

360

400

444-445

447-449

(days)

-

2975

3190

3365

75

Y50

Shaft DE Special to Customer Specifications

Consult Factory

Y51

Shaft ODE Special to Customer Specifications

Consult Factory

2007 Low Voltage AC Motors Selection and Pricing Guide

6-13

Dimensions

Dimensions

sensors for tripping* C

Typical Performance

Typical Performance

PROTECTIVE DEVICES

INVERTER Duty Severe Duty

Modifications/Accessories

SHAFTS (continued)

SHAFT SEALS

Standard dimension are shown in the Dimensions section. The following opposite drive end standard double-end shafts are available at the price addition shown below. Applicable to GP (cast iron), SD, RGZESD, RGZEESD, RGZZESD motors only.

All SD, RGZPSD, RGZESD, RGZEESD motors 140 frame and larger have a shaft seal on the drive end which prevents contaminants from entering the bearing cavity. If customer requires Inpro/Seal® bearing isolators suitable in washdown and high dust atmospheres, make the price addition from the table. Not available on open drip-proof motors. Contact factory for vertical mounting and hazardous duty motors.

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

INVERTER Duty Severe Duty

Modifications/Accessories

List Price Adder $ Order

Lead Time Modifications Accessories

List Price Adder $ 91

Order Code - M52 NEMA Standard Long Shaft FN-FW FV Key List Price Length Adder $ 1.62 1.38 0.91 91

Lead Time (days) 60

140 180 210 250 280 320

Shaft Seal - Slinger & O-Ring (4 Pole and slower)

L79

60

444-445

447-449

(days)

145

145

145

5

Inpro Seal - Drive End*

363 363 379 442 458 482

553

679

742

742

5

L80

Inpro Seal - Opposite Drive End**

363 363 379 442 458 482

553

679

742

742

5

L81

Inpro Seal - Both Ends**

726 726 758 884 916 964 1106 1358

1484

1484

5

L84

Brass Seal - Drive End***

102

102

5

42

85

400

115

42

60

360

85 115

42

60

44

59

72

87

102

* Available only for SD, RGZPSD, RGZESD, RGZEAD, RGZESDB, RGZTESD, RGZEESD, RGZESDI and RGKESDI motors. ** Available only for SD and RGZEESD motors. *** Available only for RGZZESD motors. Note: Order code L76 is not applicable to SD motors.

Modifications Accessories

Key

Order Code - M53 NEMA Standard Short Shaft FN-FW FV Key Length .— .— .—

Modification

L76

Lead Time

FU

143-145T

0.625

.188

182-184T

0.875

.188

.—

.—

.—

91

2.25

2.00

1.41

91

60

SOFTWARE

213-215T

1.125

.25-.25

—

.—

.—

91

2.75

2.50

1.75

91

60

254-256T

1.375

.312-.312

.—

.—

.—

122

3.37

3.12

2.37

122

60

284-286T

1.625

.375-.375

3.25

3

1.87

185

4

3.75

2.87

185

60

Specify software with the following order codes. Make list price additions according to the table below. For special software requirements not listed, refer to your Siemens representative for quotation.

324-326T

1.875

.50-.50

3.75

3.50

2

266

4.62

4.37

3.25

266

60

364-365T

1.875

.50-.50

3.75

3.50

2

301

4.62

4.37

3.25

301

60

404-405T

2.125

.50-.50

4.25

4

2.75

333

5.25

5

3.87

333

60

D05

444-449T

2.375

.625-.625

4.75

4.50

3

368

5.87

5.62

4.25

368

60

F00

Base Description Documentation in Spanish Certificate of compliance - copy of original

Typical Performance

Frame

Part Number

Lead Time

Code

Double-End Shafts, Standard Steel - Drive End Standard - Opposite Drive End as Follows

Typical Performance

Frame Size

List Price Lead Time Adder $ (days) NC 15 200

15

30

15

customer P.O. must accompany order. F40

Used to eliminate shaft currents. For combinations of encoder and ground brush, contact factory. Voltage - Standard voltage is 230 or 460 volts, 3 phase, 60 hertz, for 1-20 HP ratings. Standard voltage is 460 volts for 25 HP and larger. Other voltage and 50 hertz ratings available. Consult Siemens. For RGZESDI motors only. Order Code L29

List Price Modification Adder $ Shaft Grounding Brush 1920

Lead Time (days) 60

Standard Data Transmittal and certification sheet including motor description, nameplate data

F42

Standard tabulated outline dimension sheet

30

15

F44

Standard Conduit box outline dimension sheet

30

15

F45

Standard wiring/connection diagram

30

15

F46

Standard Installation, Operation and

30

15

30

15

175

15

500

15

350

15

350

15

850

15

Dimensions

Dimensions

SHAFT GROUNDING BRUSH

maintenance bulletins F47

Standard renewal parts bulletin for standard construction

F49

Standard tabulation performance data sheets typical data; 460 only

F03

Standard performance curves, single page format includes curves of speed vs torque, amps, horsepower vs p.f., efficiency, amps, speed; based on typical data.

F43

Non-standard outline drawings or special construction or accessories

F50

Completion of customer specific tabular data sheets using typical performance data only

F07

Special calculated data, i.e. time current, critical speed, B-10 verification on standard Siemens format. (460 V only)

For any non-Siemens standard data format or special data not detailed above, contact factory with complete details for price additions.

6-14

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

6-15

INVERTER Duty Severe Duty

Modifications/Accessories

Lead Time Modifications Accessories

Frame Size

Code A40 A41

Modification

143-184

Space Heaters - 115V, Single Phase

146

Space Heaters - 230V, Single Phase

146

213-256

284-326

364-365

146

218

262

146

218

262

List Price Adder $

Lead Time 404-405 320 320

444-445 379 379

447-449 428 428

(days)

Order

5

Code

5

F10

Routine Test Report Routine Test Report (Witnessed)

Lead Time (days)

Frame Size Testing

140

180

210

250

280

200

200

200

200

200

320

360

200

400

200

444

200

445

200

447

449

200

200

200

*

1100 1100 1100 1100 1100 1320 1500

1720 1860 2140

2420

3040

**

7400 8040 8500

Y52

Space Heaters - Special Voltage, Single Phase

292

292

436

524

640

758

856

60

F12

A42

Space Heaters - 115V, Single Phase, Division 2

292

292

436

524

640

758

856

5

F15

Complete Test

4560 4560 4560 4560 4560 5300 6480

8960 13520

*

Complete Test (Witnessed)

6840 6840 6840 6840 6840 7960 9720 11100 12060 12760 13440 20280

**

3420 3420 3420 3420 3420 3975 4860

A44

Space Heaters - 230V, Single Phase, Division 2

292

292

436

524

640

758

856

5

F17

A43

Space Heaters - 115V, Single Phase, Ex. Proof*

292

292

436

524

640

758

856

60

F27

Calibration Test

F36

Electrical Duplicate (Routine Test)

F37

Electrical Duplicate (Complete Test)

F30

Noise Test

2800 2800 2800 2800 2800 2800 3600

F32

Noise Test (Witnessed)

4400 4400 4400 4400 4400 4400 5200

5200 5200 5200

F20

Routine Test Report with Vibration Test

F22

Routine Test Report with Vibration Test (Witnessed)

* Only for hazardous duty motors Notes: • Leads marked H1 & H2 • Space Heaters are not available for DP (140-360 frame) motors. • List price addition covers space heaters installed in motors with leads terminated in the main conduit box. • NEC (2005) requires any Division 2 motor that is not agency certified and is a general purpose non-hazardous enclosure to permanently mark on a visible nameplate on the motor surface the max surface temp based on 40°C ambient - this plate will show 200°C. CAUTION: Use in Division 2 areas with iginition temperatures below 250°C (250 x .80 = 200) should be avoided. [Reference: 501-8(b)].

TESTING All Siemens motors are given a routine line test per NEMA MG1 and IEEE-112. A description is given below:

CALIBRATION TESTS Calibration test consists of 0-125% rated load test measurement of speed, torque, current, power factor and efficiency, at rated voltage. Data is curve plotted on Siemens standard format. Foot mounted motors only. NOISE TESTS Tests to verify sound levels can be performed. These tests are conducted per procedures defined in IEEE-85. Tests are performed under no load conditions.

200

200

200

200

200

300

300

300

300

300

300

300

400

400

400

400

400

400

5550 6030 6375 200

300

300

300

300

300

*

3600 3600 3600

3600

3600

*

5200

5200

**

400

400

400

*

2200 2200 2200

2200

2200

**

400

400

200

*

200

400

2200 2200 2200 2200 2200 2200 2200

6720 10140

200

200

*

* Add 5 days to delivery for testing ** Customers will be notified approximately 2 weeks before testing. Refer to factory for prices of test reports for adjustable speed drives. Multispeed motor test reports are priced based upon the number of speeds tested. List prices are at the following percentage of the single speed price: One speed tested 100% Two speeds tested 150% Pricing: Five copies of each test report are provided on 8.5” x 11” paper suitable for reproduction. Additional copies are available for $35 List per copy.

VERTICAL JACKING PROVISIONS (280T-449T) This option is provided on foot mounted motors only. It is used to assist the installer in proper alignment of the motor shaft with the driven piece of equipment for shimming purposes. Siemens will provide the tapped hole (one per foot), four per motor. A 1/2-13 UNC threaded hole will be provided on 280T frame, a 3/4-10 UNC threaded hole on 320T-360T and a 7/8-14 UNF threaded hole on 400T-440T frames. The customer is responsible for providing the bolts. Order Code M39

Modification Vertical Jacking Provision*

List Price Adder $ 600

Dimensions

SPECIAL TESTS For tests or reporting format other than those listed in the following table. Contact Siemens with complete specification for price additions.

200

Typical Performance

ROUTINE TEST Routine test consists of the following items tested in accordance with IEEE standard 112. • No Load Current • No Load Speed • Locked-Rotor Current • Winding Resistance • High Potential • Bearings/Vibration Check Vibration data is NOT recorded with routine test. If required, please add per the following table. Test report of routine test is based on IEEE Std. 112 Form A-1 and includes complete nameplate information.

COMPLETE TEST Complete test consists of following items tested in accordance with NEMA and IEEE-112 test standards. • Full Load Heat Run • Temperature Rise at F.L. • Winding Resistance • Rated F.L. Slip • No Load Current • Breakdown Torque • Locked Rotor Torque-Amps • High Potential Tests • Efficiencies @ 100, 75, 50 Percent Load • Power Factor @ 100, 75, 50 Percent Load Test report of complete test is based on IEEE Std. Form A-2 and includes complete nameplate information.

200

Lead Time (days) 5

* Not available for DP (140-360 frame) motors.

VIBRATION DETECTORS List Price Adder $ Order

Frame Size

Code A66 A67

Modification

Lead Time

280

320

360

400

444-445

447-449

(days)

Model 366 - D8 120VAC *

2650

2650

2650

3250

3250

3250

75

Vibration sensors (PMC/Beta) on D.E. & O.D.E*

2375

2375

2375

2875

2875

2875

75

Vibraswitch Robert Shaw malfunction detector

* Not available for DP (140-360 frame) motors.

VOLTAGE Standard 50 hertz voltages are 220, 380, 400, 415, 440, 550 and 220/380. Standard 60 hertz voltages are 200, 230, 460, 575 and 230/460. List Price Adder $ Position

6-16

2007 Low Voltage AC Motors Selection and Pricing Guide

Frame Size

Code 12&13

Modification

9-0 + M1Y 9-0 + M2Y

Lead Time

140 180 210 250 280 320

360

400

444-445

447-449

(days)

Special Voltage 200-460V*

81

81

81

112 134 323

366

479

796

979

60

Special Voltage 461-600V*

81

81

81

112 134 323

366

479

796

979

60

M1Y and M2Y = Special Voltage * Not available for DP (140-360 frame) motors.

Modifications Accessories

Typical Performance

Order

Lead Time

Dimensions

TESTING (continued) List Price Adder $

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

SPACE HEATERS

INVERTER Duty Severe Duty

Modifications/Accessories

2007 Low Voltage AC Motors Selection and Pricing Guide

6-17

.• HP x .746 = kW kW x 1.341 = HP Lead Time

• Torque (Newton - meters):

• Temperature:

Nm x .7376 = Lb. - Ft. (Lb. Ft. x 1.356 = Nm) kW x 1.341 = HP (HP ÷ 1.341 = kW) (HP x .746 = kW) °C = 5/9 (°F - 32) °F = (9/5 x °C) + 32

°

To find amperes at various voltages: • 575 V Data = 460 V Amperes x .80 • 230 V Data = 460 V Amperes x 2.0 • 200 V Data = 460 V Amperes x 2.3 (Amperes = Full Load, Locked Rotor and No Load Values - from data pages)

° All other data (kVA Code, Efficiencies, Power Factors, Torques and Stall Times) remain same as 460 V Data (winding connections can change - rarely - with voltage designs).

6-18

2007 Low Voltage AC Motors Selection and Pricing Guide

95.8

95.0

95.4

94.5

95.0

94.1

94.5

93.6

94.1

93.0

93.6

92.4

93.0

91.7

92.4

91.0

91.7

90.2

91.0

89.5

90.2

88.5

89.5

87.5

88.5

86.5

87.5

85.5

86.5

84.0

85.5

82.5

84.0

81.5

82.5

80.0

81.5

78.5

80.0

77.0

78.5

75.5

77.0

74.0

75.5

72.0

74.0

70.0

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

Dimensions

• Typical Performance Data Notes:

95.4

Typical Performance

Typical Performance

• Power (Kilowatts):

~ Lb. Ft.2 kgm2 x 23.73 = 2 (Lb. Ft. ÷ 23.73 =~ kgm2) (Lb. Ft.2 x .042 =~ kgm2) GD2 (kgfm2) x 5.933 = Lb. Ft2 kgfm2 ÷ 4 = kgm2

96.2

Modifications Accessories

Modifications Accessories

• Inertia (Kilogram - meter2):

95.8

Lead Time

HP x 5250 • Torque (Lb. - Ft.) = RPM Torque (Lb. - Ft.) x RPM • HP = 5250 • WK2 (Inertia - Lb. Ft.2) at Motor Shaft = (Load RPM ÷ Mtr. F.L. RPM)2 x Load WK2

96.5

INVERTER Duty Hazardous Duty

When NEMA Then Minimum Nominal F.L. Efficiency is:F.L. Efficiency is:

INVERTER Duty Hazardous Duty

INVERTER Duty Severe Duty

Technical Notes

INVERTER Duty Severe Duty

Notes

7-1

INVERTER Duty Severe Duty

General Purpose - ODP Motors

DP10

HIGH EFFICIENT

INVERTER Duty Hazardous Duty

1

1800 1750 143T

Lead Time

J

81.5

82.5

82.5

1/2 65

3/4 75

Full Load 82

3.1

300

BreakDown (%) 350

Hot (Sec) 7

14

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

wye

100 3600 3560 365TS

32.2 115

725

G

91.5

34.2 117

725

G

93

Winding Cold Connec(Sec) tion

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

BreakDown (%)

LR Stall Time Hot (Sec)

Winding Cold Connec(Sec) tion

Full Load

1/2

3/4

Full Load

93

93

79.5

84.5

87.5

148

160

220

7

12

delta

94

94.1

76.5

83

85.5

296

190

240

7

12

delta

3/4

1

1.9

12

L

79

80

80

41

53

63

4.6

240

300

7

15

wye

1.5 3600 3420 143T

0.9

2.1

16

L

81.5

82.5

82.5

67

79

83

2.3

220

290

7

14

wye

100 1200 1185 444T

33

116

725

G

93.8

94.5

94.1

76

83

85.5

443

140

210

37

42

delta

1.5 1800 1740 145T

0.9

2.1

15

J

83

84

84

64

74

81

4.6

200

240

7

14

wye

125 3600 3560 404TS

43

144

908

G

92

93.6

93.6

80

85

87

185

160

220

7

12

y-delta

1.5 1200 1160 182T

1.7

2.6

16

L

83

84

84

42

55

64

6.8

200

270

7

14

wye

125 1800 1775 405T

44

145

908

G

93.5

94.5

94.5

77

83.5

86

370

180

220

7

12

y-delta

1.2

2.7

24

L

82.5

84

84

69

80.5

85

3.1

210

280

7

14

wye

125 1200 1185 445T

40

145

908

G

94.3

94.5

94.1

77

83.5

85.5

554

140

210

37

42

delta

52

172 1085

G

92.5

93.6

93.6

81.5

86

87.5

222

160

230

7

12

y-delta

81

190 1085

G

94.1

94.9

95

63

72.5

77.5

441

170

220

16

20

y-delta

1200 1140 145T

2

3600 3420 145T

2

1800 1720 145T

1.3

2.8

17

J

83

84

84

64

74

81

6.1

200

240

7

14

wye

150 3600 3560 405TS

2

1200 1160 184T

2.4

3.5

24

L

84.5

85.5

85.5

43

56

65

9.1

220

280

7

14

wye

150 1800 1785 444T

3

3600 3425 145T

1.4

4

32

K

83

84

84

70.5

81.5

86.5

4.6

200

270

7

14

wye

150 1200 1185 445T

49

174 1085

G

94.9

94.9

94.5

77

83.5

85.5

665

150

205

30

36

delta

3

1800 1745 182T

1.8

4.1

29

K

86.5

87

86.5

63.5

75

81

9.1

240

300

7

14

wye

200 3600 3570 444TS

55

223 1450

G

94.5

94.7

94.5

82

87.5

89

294

140

220

20

24

y-delta

3

1200 1170 213T

1.8

4.5

28

H

85.5

86.5

86.5

58

69

74

13.6

180

250

7

14

delta

200 1800 1785 445T

78

235 1450

G

94.8

95.1

95

73.5

81.5

84

588

175

210

16

20

y-delta

5

3600 3470 182T

1.8

6.3

45

H

84.5

85.5

85.5

71

82

88

7.5

160

240

7

14

wye

200 1200 1185 447T

73

232 1450

G

95

95

94.5

76

82.5

85.5

886

150

205

23

28

delta

55

277 1825

G

93.6

94.2

94

84.5

88.6

90

369

115

240

20

23

y-delta

315 1825

G

92.5

94

94

64

75

79

738

100

200

24

28

y-delta

1800 1740 184T

2.7

6.7

46

J

86.5

87.5

87.5

65

75

82

15.2

240

300

7

14

wye

5

1200 1160 215T

2.9

7.1

46

J

86.5

87.5

87.5

59

70

75.5

22.6

230

280

7

14

delta

250 1800 1785 445T 120

7.5 3600 3460 184T

2

9

64

H

86.5

87.5

87.5

84

90

90

12

200

270

7

14

wye

250 1200 1185 449T

96

288 1825

G

95.5

95.5

95

75

83

85.5

7.5 1800 1760 213T

4

9.5

64

H

87.5

88.5

88.5

69

78

84

23

230

270

7

14

delta

300 3600 3565 447TS

60

335 2200

G

92.5

93.3

93

87

89.1

90

7.5 1200 1165 254T

4.6

10.5

64

H

87.5

88.5

88.5

60

71

76

34

200

250

7

14

delta

300 1800 1785 447TS 140

364 2200

G

92.8

94.2

94.1

75

79

82

885

100

200

12

15

pws

10

3600 3470 213T

2.9

12.5

80

H

88.5

89

88.5

80

85.5

86.5

15

170

250

7

12

delta

300 1200 1185 449TS 117

351 2200

G

94.5

94.5

94.1

75

83

85

1330

100

180

21

25

delta

10

1800 1750 215T

3.7

13

81

H

88.5

89.5

89.5

68.5

77.5

81

30

230

260

7

14

delta

350 3600 3570 447TS

70

389 2550

G

92

93.6

93.6

87

90

90

516

130

220

10

12

y-delta

delta

350 1800 1780 447TS 167

433 2550

G

93

94.5

94.5

70

78

80

1036

80

180

12

14

delta

85

442 2900

G

93

94.3

94.1

88

90

90

590

100

200

10

11

y-delta

10

1200 1165 256T

5.3

13.5

81

H

89

90

90.2

82.5

74

78

45

200

250

7

14

1108

155

210

25

30

delta

443

130

240

11

13

y-delta

3600 3490 215T

5.7

18.5 116

G

88.5

89.5

89.5

77

84

86

23

210

260

7

14

delta

15

1800 1760 254T

6.3

19

116

G

90

91

91

70.5

78.5

81.5

45

220

270

7

14

delta

400 1800 1775 449TS 190

495 2900

G

93.5

94

94.5

70

75

80

1180

80

180

11

13

delta

15

1200 1175 284T

7.2

20.3 116

G

89

90

90.2

62.5

74

78

67

200

250

7

14

delta

450 3600 3560 449TS 120

487 3250

G

94

95.1

95

88

91

91

663

140

270

9

10

y-delta

20

3600 3515 254T

5.6

24

145

G

89

90

90.2

82

86.5

88

30

200

250

7

14

delta

500 3600 3555 449TS 143

570 3625

G

94.9

95.1

94.8

81.2

86.5

88.2

738

130

220

7

8

y-delta

20

1800 1760 256T

8.6

25

145

G

90

91

91

71

79

82

60

220

260

7

14

delta

20

1200 1170 286T

8.2

26

145

G

90

91

91

68

78

80

90

200

240

7

14

delta

25

3600 3520 256T

5.1

30

183

G

90

91

91

81.5

86

87.5

37

200

250

7

12

delta

25

1800 1765 284T 10.1

31

183

G

90

91.5

91.7

72

80

83

74

210

245

7

14

delta

25

1200 1175 324T 11.6

31

183

G

90

91.5

91.7

73

80.5

83

112

220

270

7

14

delta

30

3600 3540 284TS

36

218

G

89.5

91

91

81.5

86

87.5

45

180

240

7

12

delta

30

1800 1765 286T 10.7

36.5 218

G

91.5

92.5

92.4

72.5

80.5

84

89

200

240

7

14

delta

30

1200 1175 326T 14.2

37

218

G

91.5

92.5

92.4

73

80

82.5 134

220

270

7

13

delta

40

3600 3540 286TS 10.9

48

290

G

90.5

91.5

91.7

79

83.5

86.5

170

230

7

14

delta

40

1800 1765 324T 12.7

49

290

G

92

93

93

74

80.5

83

97

190

230

7

12

delta

40

1200 1175 364T 14.3

50

290

G

92

93

93

73

80

82.5

99

200

250

7

12

delta

50

3600 3545 324TS 15

59

363

G

91.5

92.5

92.4

79

83.5

86.5

74

170

230

7

12

delta

50

1800 1770 326T 15.8

58

363

G

92

93

93

74.5

81

83.5 149

190

230

7

12

delta

50

1200 1180 365T 17.6

62

363

G

92

93

93

73

80

82.5 223

200

260

7

12

delta

60

3600 3545 326TS 15.3

70

435

G

91

93

93

79

84

87

89

170

230

7

12

delta

60

1800 1775 364T 29.3

72

435

G

92.5

93.5

93.6

75

81.5

84

178

190

240

7

12

delta

60

1200 1180 404T 28.8

73

435

G

92.5

93.5

93.6

73

80

82.5 226

220

270

7

12

delta

75

3600 3560 364TS 23.4

87

543

G

91

93

93

79

84

87

111

160

220

7

12

delta

75

1800 1775 365T 30.1

89

543

G

93

94

94.1

76

82.5

85

222

190

250

7

12

delta

75

1200 1185 405T 35.5

91

543

G

92.5

93.5

93.6

73

80

82.5 333

220

270

7

12

delta

7-2

8.2

2007 Low Voltage AC Motors Selection and Pricing Guide

59

DOE#CC014A (140-400 frames) DOE#CC032A (440 frames)

DOE#CC014A (140-400 frames) DOE#CC032A (440 frames)

2007 Low Voltage AC Motors Selection and Pricing Guide

7-3

Dimensions

15

400 3600 3570 449TS

Typical Performance

5

250 3600 3565 445TS

Modifications Accessories

Modifications Accessories

10

Full Load

Current [A]

LR Stall Time

Lead Time

Typical Performance

1.4

3/4

Torque Full Lckd Load Rotor (lb-ft) (%)

100 1800 1775 404T

1

Dimensions

0.6

1/2

Power Factor (%)

INVERTER Duty Hazardous Duty

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

HIGH EFFICIENT

460 Volts, NEMA Design B, 40ºC Ambient

460 Volts, NEMA Design B, 40ºC Ambient Current [A]

DP10

INVERTER Duty Severe Duty

General Purpose - ODP Motors

INVERTER Duty Severe Duty

GP10A / GP10 / SD10

RGZP / RGZPSD

Current [A]

1

1800 1750 143T 1200 1150 145T

0.8 1 1

1.4 1.5 1.6

14 13 9

N M J

75.5 80 79.5

3/4 79 82.5 81

80 82.5 80

1/2 63 53 53

3/4 74 66 66

Full Load 81 76 73

Full Load (lb-ft) 1.5 3 4.6

Torque Lckd Rotor (%) 240 290 190

LR Stall Time BreakDown (%) 460 410 300

Hot (Sec) 12 15 13

Current [A]

Winding Cold Connec(Sec) tion 16 22 22

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

Power Factor (%)

Full Load

1/2

Torque Lckd Rotor (%)

LR Stall Time BreakDown (%)

Hot (Sec)

Winding Cold Connec(Sec) tion

1/2

3/4

wye

1

3600 3490 143T

0.8

1.4

11

K

72.1

74.8

75.5

75

86

92

1.5

280

340

15

30

wye

wye

1

1800 1745 143T

1.1

1.5

11

K

78.7

81.8

82.5

52

66

76

3

290

320

14

30

wye

wye

1

1200 1140 145T

1.3

1.8

9

J

76.4

78.8

80

42

56

65

4.6

230

290

19

40

wye wye

870 182T

1.5

2.1

9

J

77

80

81.5

36

47

56

6

160

250

50

68

wye

1

860 182T

1.2

1.9

8

H

76.6

78.9

78.5

42

54

63

6.1

220

260

20

40

0.9

2

16

L

81.5

83.5

82.5

69

81

85

2.3

220

380

13

17

wye

1.5

3600 3485 143T

0.9

2

16

K

78

82

82.5

69

79

85

2.3

270

320

13

28

wye

1.5 1800 1750 145T

1.4

2.2

20

M

82

84

84

55

69

76

4.5

340

420

12

17

wye

1.5

1800 1740 145T

1.4

2.2

17

K

80.7

83.5

84

54

67

76

4.5

290

320

13

29

wye

1.5 1200 1170 182T

1.4

2.4

15

K

84

85.5

85.5

52

64

68

6.7

220

420

27

36

wye

1.5

1200 1160 182T

wye

1.5

1

900

900

865 184T

2.3

3

17

3600 3495 145T

1.2

2.6

2

1800 1740 145T

1.8

3

25

L

2

1200 1170 184T

1.8

3.1

25

K

2

3.3

16

H

900

870 213T

L

78.5

82

82.5

35

47

56

9.1

220

380

43

63

1.5

2.3

16

K

81.6

84.2

85.5

50

63

71

6.8

280

320

22

33

wye

860 184T

1.8

2.6

13

H

78

80.4

80

45

58

68

9.2

220

270

18

30

wye

3600 3495 145T

1.1

2.5

22

K

79.9

83.2

84

73

83

89

3

270

320

15

33

wye

900

84.5

84

66

78

85

3

230

400

13

17

wye

2

83

84.5

84

54

68

77

6

370

440

13

20

wye

2

1800 1735 145T

1.9

2.9

21

K

80.7

83.6

84

52

67

77

6.1

290

310

12

25

wye

85

87

86.5

49

61

70

9

225

400

19

26

wye

2

1200 1160 184T

1.9

3

22

K

84.5

86

86.5

50

63

72

9.1

220

300

21

32

wye

84

84.5

84

51

63

68

12.1

170

340

22

38

wye

2

865 213T

2.2

3.3

17

H

80

82

82.5

46

60

69

200

290

18

30

wye

85.5

73

84

89

4.5

230

320

16

37

wye

9.1

82.5

900

12

3

3600 3515 182T

1.5

3.7

32

K

83

85.5

85.5

67

80

85

4.5

170

340

30

20

wye

3

3600 3505 182T

1.7

3.7

32

K

81.5

85

3

1800 1750 182T

2

4

32

K

86.5

88

87.5

59

72

78

9

210

370

15

25

wye

3

1800 1740 182T

1.8

3.9

30

K

87.5

88

87.5

65

76

82

260

300

16

35

wye

wye

3

1200 1165 213T

2.3

4

32

K

85.8

87.6

87.5

58

73

80

14

210

300

17

35

wye

wye

3

865 215T

3.1

4.7

26

H

82.5

84.2

84

48

62

71

18

190

280

15

32

wye

3 3

1200 1170 213T 900

870 215T

2.2

4.2

32

K

86.5

3

4.8

25

H

85.5

87.5 86.5

87.5 85.5

57 45

70 59

76 68

13 18

220 200

360 310

16 19

24 31

900

3600 3505 184T

2.3

6.2

46

J

87

88

87.5

72

82

85

190

400

13

25

wye

5

3600 3490 184T

1.8

5.8

46

J

86.5

87.8

87.5

82

89

92

260

320

12

26

wye

5

1800 1735 184T

2.9

6.7

46

J

88.5

88.5

87.5

64

75

79

15

190

320

12

24

wye

5

1800 1730 184T

3.2

6.5

46

J

87.5

88.2

87.5

63

75

82

15

260

300

17

36

wye

5

1200 1165 215T

3.3

6.8

46

J

88

88.5

87.5

62

74

79

23

200

340

13

20

wye

5

1200 1160 215T

3.3

6.8

46

J

87

88

87.5

60

72

79

23

210

300

14

29

wye

865 254T

4.1

7.5

40

H

86

87

86.5

53

66

72

30

180

260

13

25

wye

7.5

875 254T

5.5

8.8

33

F

85.5

87

86.5

43

54

62

30

189

197

65

115

wye

5

7.5 3600 3520 213T

3.5

9

63

H

86.5

88.5

88.5

75

84

89

11

190

360

16

29

wye

7.5

3600 3515 213T

3.4

8.8

64

H

87

88

88.5

77

86

90

11

190

280

14

29

wye

25

wye

7.5

1800 1750 213T

4.2

9.5

64

H

89

90

89.5

66

77

83

23

210

270

14

29

wye

1200 1170 254T

4.5

9.8

5

900

4.1

7.5 1200 1175 254T 7.5

875 256T

3600 3515 215T

10

900

9.5

63

H

89.5

90

89.5

66

77

82

23

200

341

15

5.5 11

63

H

88.5

90

89.5

55

68

78

34

160

279

21

37

wye

7.5

7

13

50

G

87

88

87.5

44

57

62

45

188

197

50

100

wye

7.5

4

11.5

81

H

90

90.5

89.5

79

86

89

15

190

380

14

27

wye

10

60

H

89.9

90

89.5

67

76

80

34

180

250

20

39

wye

6.6 12

64

H

87

88

87.5

49

61

69

46

190

260

15

30

wye

3600 3505 215T

4

12

81

H

89

89.8

89.5

80

89

91

15

190

260

14

29

wye

10

1800 1750 215T

5.4 13

81

H

89.5

90

89.5

68

79

84

30

210

270

15

30

wye

1200 1165 256T

10

1800 1750 215T

5.7 12.5

81

H

89.5

90

89.5

66

77

82

30

210

360

13

23

wye

10

1200 1175 256T

7

81

H

89

90

89.5

58

69

75

45

172

264

15

31

wye

10

14

900

5

13

75

G

89.9

90.1

89.5

67

77

81

45

170

250

18

35

wye

81

H

89.4

90.9

91

50

61

69

60

150

220

15

30

delta

15

3600 3530 254T

5.6 18

116

G

88

89.5

90.2

78

85

87

22

210

290

21

48

wye

15

1800 1760 254T

8.8 19

116

G

90

91

91

64

75

81

45

231

264

17

40

wye

15

3600 3530 254T

5

17

116

G

88.5

90

90.2

84

90

92

22

190

260

17

31

wye

20

3600 3515 256T

6.5 24

145

G

88.5

90

90.2

81

87

88

30

210

268

18

48

wye

15

1800 1760 254T

7.3 19

116

G

91

91.5

91

69

78

83

45

190

260

18

35

wye

20

1800 1755 256T 11

145

G

91.5

91.5

91

66

77

79

60

220

250

13

38

wye

15

1200 1175 284T 10

20

116

G

90.2

90.9

90.2

57

71

78

67

160

270

20

45

delta

23

116

G

90.1

91.4

91

50

60

67

90

150

220

18

35

delta wye

15

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

875 286T 14

20

3600 3525 256T

7.4 23

145

G

88.3

89.9

90.2

82

86

90

30

180

260

17

25

20

1800 1755 256T

9.1 26

145

G

90.9

91.4

91

67

77

81

60

190

270

18

35

wye

20

1200 1175 286T 12

145

G

90.7

90.9

90.2

63

74

80

89

160

250

19

43

delta

20

7-4

900

875 284T

9.1 15

10

25

900

865 256T

900

880 324T 18

26 31

145

G

90

91.2

91

50

61

67

119

140

200

15

35

delta

25

3600 3525 284TS

8

29

183

G

90.5

90.4

91

82

88

89

37

160

250

16

30

delta

25

1800 1765 284T 13

29

183

G

92.6

92.9

92.4

72

82

87

74

220

280

19

40

delta

25

1200 1180 324T 15

33

183

G

92.1

92.3

91.7

58

69

77

111

170

240

25

50

delta

30

3600 3525 286TS

9.5 34

218

G

91.9

91.8

91

86

89

90

45

160

250

16

30

delta

30

1800 1765 286T 15

35

218

G

92.6

93

92.4

72

84

88

89

220

280

19

40

delta

30

1200 1180 326T 19

39

218

G

91.9

92.2

91.7

59

72

79

134

170

240

25

50

delta

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-5

Dimensions

7.5 1800 1750 213T

900

7.5

Typical Performance

5

Modifications Accessories

2

2

23

H

900

3/4

Full Load

Full Load (lb-ft)

1.5 3600 3490 143T

1.5 Modifications Accessories

3600 3520 143T

1/2

Full Load

Power Factor (%)

Lead Time

Lead Time

1

Typical Performance

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

HIGH EFFICIENT

460 Volts, NEMA Design B, 40ºC Ambient

460 Volts, NEMA Design B, 40ºC Ambient

1

Dimensions

HIGH EFFICIENT

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

General Purpose & Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

General Purpose & Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe & Hazardous Duty Motors

RGZP / RGZPSD

RGZESD / RGZZESD / RGZESDB

HIGH EFFICIENT

Lead Time Modifications Accessories

1/2

40 3600 3530 324TS 13

46

290

G

91.3

40 1800 1770 324T

15

47

290

G

93.5

40 1200 1180 364T

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

BreakDown (%)

LR Stall Time Hot (Sec)

Current [A]

Winding Cold Connec(Sec) tion

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

3/4

Full Load

1/2

3/4

Full Load

1/2

92.1

91.7

85

89

90

60

150

250

22

45

delta

1

1800 1745 143T

1.1

1.5

11

K

78.7

93.6

93

76

83

86

119

190

240

20

40

delta

1

1200 1140 145T

1.3

1.8

9

J

76.4

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

BreakDown (%)

LR Stall Time Hot (Sec)

Winding Cold Connec(Sec) tion

3/4

Full Load

1/2

3/4

Full Load

81.8

82.5

52

66

76

3

290

320

14

30

wye

78.8

80

42

56

65

4.6

230

290

19

40

wye

52

290

G

93

93.3

93

60

71

77

178

170

230

29

55

delta

860 182T

1.2

1.9

8

H

76.6

78.9

78.5

42

54

63

6.1

220

260

20

40

wye

55

363

G

92

92.7

92.4

86

91

92

74

150

250

18

37

delta

1.5 3600 3485 143T

0.9

2

16

K

78

82

82.5

69

79

85

2.3

270

320

13

28

wye

50 1800 1770 326T

18

58

363

G

93.4

93.5

93

78

85

87

148

190

240

20

40

delta

1.5 1800 1740 145T

1.4

2.2

17

K

80.7

83.5

84

54

67

76

4.5

290

320

13

29

wye

50 1200 1180 365T

30

66

363

G

93.2

93.6

93

61

72

77

223

170

230

29

55

delta

1.5 1200 1160 182T

1.5

2.3

16

K

81.6

84.2

85.5

50

63

71

6.8

280

320

22

33

wye

60 3600 3545 364TS 19

68

435

G

93.2

93.5

93

81

87

89

89

160

250

16

28

delta

1.5

860 184T

1.8

2.6

13

H

78

80.4

80

45

58

68

9.2

220

270

18

30

wye

60 1800 1775 364T

21

71

435

G

93.9

94.1

93.6

74

82

85

178

160

240

22

45

delta

2

3600 3495 145T

1.1

2.5

22

K

79.9

83.2

84

73

83

89

3

270

320

15

33

wye

60 1200 1185 404T

27

74

435

G

94.5

94.3

93.6

75

80

81

266

165

230

18

38

delta

2

1800 1735 145T

1.9

2.9

21

K

80.7

83.6

84

52

67

77

6.1

290

310

12

25

wye

75 3600 3545 365TS 22

85

543

G

93.2

93.4

93

82

87

89

111

160

260

16

27

delta

2

1200 1160 184T

1.9

3

22

K

84.5

86

86.5

50

63

72

9.1

220

300

21

32

wye

75 1800 1775 365T

27

87

543

G

94.4

94.6

94.1

74

83

85

222

155

240

22

45

delta

2

865 213T

2.2

3.3

17

H

80

82

82.5

46

60

69

200

290

290

30

wye

75 1200 1185 405T

35

93

543

G

94.1

94.3

93.6

78

80

81

333

170

240

13

27

delta

3

3600 3510 182T

1.7

3.6

32

K

83.8

86.2

86.5

75

84

90

4.5

230

320

15

34

wye

100 3600 3565 405TS 19

112

725

G

93.7

93.8

93.6

89

91

91

147

120

210

12

25

delta

3

1800 1740 182T

1.8

3.9

30

K

87.5

88

87.5

65

76

82

9.1

260

300

16

35

wye

100 1800 1780 405T

28

114

725

G

94.7

94.9

94.5

81

86

87

295

160

200

22

43

delta

3

1200 1165 213T

2.3

4

32

K

85.8

87.6

87.5

58

73

80

14

210

300

17

35

wye

100 1200 1185 444T

38

117

725

G

93.9

94.2

94.1

79

84

85

443

165

230

18

38

delta

3

865 215T

3.1

4.7

26

H

82.5

84.2

84

48

62

71

18

190

280

15

32

wye

125 3600 3575 444TS 31

138

908

G

94.2

94.6

94.5

84

89

90

184

120

200

24

40

delta

5

3600 3490 184T

1.8

5.8

46

J

86.5

87.8

87.5

82

89

92

8

260

320

12

26

wye

125 1800 1785 444T

43

145

908

G

93.5

94.5

94.5

78

84

86

368

160

200

26

56

delta

5

1800 1730 184T

3.2

6.5

46

J

87.5

88.2

87.5

63

75

82

15

260

300

17

36

wye

125 1200 1185 445T

44

145

1200 1160 215T

wye

1

908

G

94.1

94.4

94.1

80

85

86

554

140

220

15

32

delta

5

150 3600 3575 445TS 37

165 1085

G

94.2

94.6

94.5

87

89

90

221

145

235

23

40

delta

5

150 1800 1785 445T

45

170 1085

G

94.6

95.1

95

81

86

87

441

150

200

25

53

150 1200 1185 447T

900

900

900

900

12

3.3

6.8

46

J

89

89.7

88.5

59

71

78

23

210

300

14

29

865 254T

4.1

7.5

40

H

86

87

86.5

53

66

72

30

180

260

13

25

wye

delta

7.5 3600 3515 213T

3.4

8.8

64

H

87

88

88.5

77

86

90

11

190

280

11

25

wye

900

171 1085

G

95.1

95.4

95

81

86

87

665

120

200

12

25

delta

7.5 1800 1750 213T

4.2

9.5

64

H

89

90

89.5

66

77

83

23

210

270

14

29

wye

212 1450

G

94.4

95.1

95

90

92

93

294

120

200

16

27

delta

7.5 1200 1170 254T

4.5

9.8

60

H

90.6

90.9

90.2

59

72

78

34

180

250

18

35

wye

200 1800 1785 447T

61

225 1450

G

94.9

95.2

95

81

86

87

588

150

200

18

31

delta

7.5

6.6 12

64

H

87

88

87.5

49

61

69

46

190

260

15

30

wye

200 1200 1185 449T

60

224 1450

G

94.8

95.3

95

82

87

88

886

120

200

18

38

delta

10 3600 3505 215T

4

12

81

H

89

89.8

89.5

80

89

87

15

190

260

14

29

wye

10 1800 1750 215T

5.4 13

81

H

89.5

90

89.5

68

79

84

30

210

270

15

30

wye

10 1200 1165 256T

5

13

75

G

91.7

91.5

90.2

65

75

80

45

170

250

18

35

wye

10

9.1 15

81

H

89.4

90.9

91

50

61

69

60

150

220

15

30

delta

900

900

865 256T

875 284T

15 3600 3530 254T

5

17

116

G

88.5

90

90.2

84

90

92

22

190

260

17

31

wye

15 1800 1760 254T

7.3 19

116

G

91.7

92.1

91.7

68

78

82

45

190

260

18

35

wye

15 1200 1175 284T 10

20

116

G

91

91.7

91

57

71

77

67

160

270

20

45

delta

15

23

116

G

90.1

91.4

91

50

60

67

90

150

220

18

35

delta

20 3600 3525 256T

7.4 23

145

G

88.3

89.9

90.2

82

86

90

30

180

260

17

25

wye

20 1800 1755 256T

9.1 26

145

G

92.1

92.4

91.7

67

76

80

60

190

270

18

35

wye

145

G

92.1

92.4

91.7

62

73

79

89

160

250

19

43

delta delta

900

875 286T 14

20 1200 1175 286T 12 20

7-6

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

900

26

880 324T 18

31

145

G

90

91.2

91

50

61

67

119

140

200

15

35

25 3600 3525 284TS 8

29

183

G

92

92.2

91.7

80

85

88

37

160

250

16

30

delta

25 1800 1765 284T 13

29

183

G

93.3

93.6

93

72

82

87

74

220

280

19

40

delta

25 1200 1180 324T 15

33

183

G

92.2

92.7

92.4

57

69

77

111

170

240

25

50

delta

25

38

183

G

89.2

90.5

90.2

50

61

68

149

150

200

22

40

delta

30 3600 3525 286TS 9.5 34

218

G

92

92.2

91.7

84

89

90

45

160

250

16

30

delta

30 1800 1765 286T 15

35

218

G

93.2

93.6

93

71

82

86

89

220

280

19

40

delta

30 1200 1180 326T 19

39

218

G

92.6

92.9

92.4

58

70

78

134

170

240

25

50

delta

30

47

218

G

89.9

91.3

91

50

62

66

178

150

200

22

40

delta

900

900

880 326T 22

885 364T 26

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-7

Dimensions

45

200 3600 3575 447TS 39

Typical Performance

24

50 3600 3530 326TS 15

Modifications Accessories

Typical Performance

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

Lead Time

Dimensions

Current [A]

460 Volts, NEMA Design B (except as noted), 40ºC Ambient INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

460 Volts, NEMA Design B, 40ºC Ambient

HIGH EFFICIENT

INVERTER Duty Severe Duty

General Purpose & Severe Duty - TEFC Motors

460 Volts, NEMA Design B (except as noted), 40ºC Ambient Current [A] kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

3/4

40 3600 3530 324TS

94

94.1

INVERTER Duty Severe Duty Lead Time

12 15

45 47

290 290

G G

94

Full Load 93.6

460 Volts, NEMA Design B, 40ºC Ambient

Power Factor (%)

1/2

3/4

Full Load

80

87

89

Torque Full Lckd Load Rotor (lb-ft) (%) 60

150

Current [A]

LR Stall Time BreakDown (%)

Hot (Sec)

250

22

45

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

delta

1/

70.5

0.25

42

Winding Cold Connec(Sec) tion

94.2

93.6

77

82

85

119

190

240

20

40

delta

1800/ 1745/ 143T 900 850

1.3

1.8

11

0.8

0.9

3 15

40 1200 1180 364T

24

52

290

G

93.6

93.9

93.6

59

71

77

178

170

230

29

55

delta

1.5/ 1800/ 1740/ 145T

1.4

2.2

40

885 365T

36

63

290

G

90.7

92

91.7

49

60

65

237

150

200

25

40

delta

0.37

0.9

1

50 3600 3530 326TS

15

55

363

G

94.1

94.2

93.6

82

89

91

74

150

250

18

37

delta

2/

1.2

2.7

50 1800 1770 326T

18

58

363

G

94.1

94.2

93.6

77

87

86

148

190

240

20

40

delta

0.5

0.9

1.3

50 1200 1180 365T

30

66

363

G

94

94.2

93.6

60

71

76

223

170

230

29

55

delta

3/

2

4

50

28

67

363

G

92.3

92.4

91.7

64

73

76

297

140

200

25

40

delta

0.75

1.1

1.5

6

5/

3.6

6.6

46

900

900

885 404T

900 855 1800/ 1745/ 182T 900 865 1800/ 1735/ 184T 900 855 1800/ 1760/ 213T

20

19

68

435

G

93.8

94.1

93.6

80

86

88

89

160

250

16

28

delta

21

71

435

G

93.9

94.1

93.6

74

82

85

178

160

240

22

45

delta

1.2

900 865

1.9

2.4

9

60 1200 1185 404T

26

74

435

G

94.1

94.5

94.1

70

78

81

266

150

200

25

50

delta

7.5/ 1800/ 1760/ 215T

5.2

9.9

63

2.6

900 865

885 405T

30

78

435

G

92.3

92.4

91.7

67

76

79

356

140

200

30

35

delta

1.9

75 3600 3565 365TS

22

85

543

G

94.3

94.5

94.1

81

86

88

111

160

260

16

27

delta

10/ 1800/ 1770/ 254T

6

75 1800 1775 365T

27

87

543

G

94.4

94.6

94.1

74

83

85

222

155

240

22

45

delta

2.5

4.3

7.7 18.5 115 5.6

900 880

3.5

13

12.9

81

5.4

18

34

93

543

G

94.7

94.9

94.5

68

77

80

332

150

200

33

45

delta

75

885 444T

37

94

543

G

92.9

93.3

93

67

76

80

445

135

200

25

32

delta

3.7

100 3600 3570 405TS

19

108

725

G

94.6

94.7

94.1

90

92

92

147

120

200

25

45

delta

20/ 1800/ 1770/ 284T 10

100 1800 1780 405T

30

113

725

G

95

95.2

94.5

80

85

87

295

160

200

25

35

delta

100 1200 1185 444T

38

117

725

G

94.6

94.9

94.5

75

82

85

443

140

200

30

35

delta

25/ 1800/ 1765/ 286T 10.5 30

900

5

900 880 900 880

885 445T

48

123

725

G

94.2

94.5

94.1

70

78

81

593

130

200

22

30

delta

6.2

32

138

908

G

94

94.6

94.5

85

89

89

184

120

200

18

23

delta

30/ 1800/ 1770/ 324T 11.5 35

125 1800 1785 444T

42

143

908

G

95.1

95.3

95

78

84

86

368

160

200

20

25

delta

7.5

900

900 885

8

9.3

125 3600 3575 444TS

100

900 880

7.2

7.5 25

11.5

8.5 13

144

908

G

94.7

94.9

94.5

77

84

86

554

140

200

25

35

delta

40/ 1800/ 1770/ 326T 16

46

340

152

908

G

94.1

94.2

93.6

70

79

82

742

130

200

20

30

delta

10

11.2 17

81

150 3600 3575 445TS

37

164 1085

G

94.8

95.2

95

84

89

90

220

120

200

15

18

delta

50/ 1800/ 1780/ 364T 20.5 58

425

150 1800 1785 445T

45

170 1085

G

95.7

96

95.8

80

85

86

441

150

200

20

30

delta

12.5

150 1200 1185 447T

45

170 1085

G

95.4

95.6

95

81

86

87

665

125

200

28

43

delta

60/ 1800/ 1780/ 365T 26

150

885 449T

72

186 1085

G

94.1

94.5

94.1

67

76

80

890

130

200

20

25

delta

15

200 3600 3575 447TS

40

216 1450

G

94.9

95.2

95

88

90

91

294

120

200

16

20

200 1800 1785 447T

60

225 1450

G

96

96.1

95.8

81

86

87

588

150

200

18

25

200 1200 1185 449T

55

226 1450

G

95.4

95.5

95

82

86

87

886

125

200

25

32

delta

200

103

delta

75/ 1800/ 1785/ 405T 26.5 86

568

delta

19

32

120

100/ 1800/ 1790/ 444TS 41.5 118

804

25

900 890

20 31

46

178

125/ 1800/ 1790/ 445TS 46

158

1045

57

223

delta

150/ 1800/ 1785/ 447TS 64.5 176

1260

delta

37.5

241 1450

G

94.8

94.9

94.5

71

79

82

1186

125

200

15

25

delta

45

267 1825

G

95.3

95.6

95.4

90

92

92

368

120

200

12

18

delta

250 1800 1785 449T

78

281 1825

G

95.8

96

95.8

80

85

87

735

140

200

18

25

delta

250 1200 1185 449T

75

280 1825

G

95.5

95.5

95

82

87

88

1108

120

200

20

25

885 S449 111

303 1825

G

94.5

94.8

94.5

70

78

82

1483

105

200

25

32

323 2200

G

95.2

95.8

95.8

86

90

91

441

100

200

12

13

delta

200/ 1800/ 1785/ 449TS 65

900

885 S449 101

18.5 27

250 3600 3570 449TS

250

900

458

900 890

300 3600 3575 449TS

68

31

900 890

45.5 68 230

1460

346 2200

G

95

95.5

95.4

76

83

85

882

120

200

12

15

delta

51

86

291

90

336 2200

G

95.5

95.5

95

82

87

88

1329

105

200

26

33

delta

250/ 1800/ 1785/ 449TS 81

289

1835

350 3600 3570 S449SS 67

369 2550

G

95.4

95.7

95.4

90

92

93

515

80

200

20

26

delta

62.5

105

366

350 1800 1785 S449 115

390 2550

G

95.5

95.9

95.8

79

86

88

1029

100

200

25

32

delta

350 1200 1185 S449 133

395 2550

G

95.2

95.3

95

77

84

87

1551

100

200

17

20

delta

400 3600 3570 S449SS 80

418 2900

G

94.2

95.6

95.4

90

93

94

588

80

200

17

24

delta

400 1800 1785 S449 138

449 2900

G

400 1200 1185 S449 145

455 3260 H *

96

95.8

79

85

87

1176

100

200

21

26

-

95.3

94.5

79

84

87

1772

100

200

-

-

-

900 890

59

G H H

LR Stall Time BreakDown (%)

Hot (Sec) 12

3/4

1/2

74.5

75.5

47

60

69

3

250

290

48.8

52.5

34

42

50

1.5

160

250

79.7

81.9

81.5

57

70

78

4.5

250

280

48.5

53.9

55.5

47

59

62

2.3

140

225

82.7

84.3

84

63

76

83

6

235

290

60.72 67.1

70

33

43

51

3

140

225

85.5

85.4

84

69

79

84

9.1

240

290

69.8

74.1

75.5

40

53

62

4.6

135

220

84.6

85.9

85.5

63

76

83

14.9

185

225

72.05 76.9

78.5

40

51

60

7.3

120

200

85.1

86

85.5

62

76

83

22.4

175

215

70

72.5

74

46

60

69

11.5

130

210

87.8

88.7

88.5

66

77

82

29.7

165

200

75

79.7

81.5

35

45

53

14.9

110

180

89.8

90.5

90.2

69

79

84

45

160

200

79

82.9

84

37

48

55

22

120

180

88.7

89

88.5

71

81

85

59.4

190

270

80

83

84

38

50

59

30

180

250

90.3

90.4

89.5

76

84

87

74

190

240

82.9

85.2

85.5

40

52

60

37

150

200

91.9

92.3

91.7

85

77

88

89

220

270

85

87.7

88.5

44

56

61

45

150

200

92.7

92.9

92.4

73

83

88

124

200

260

85.8

88.4

88.5

41

53

62

59

150

220

H

93.3

93.5

93

73

83

86

147

180

240

86.4

88.8

89.5

38

50

58

74

130

200

G

93.3

93.5

93

73

81

85

178

160

240

86.2

88.1

88.5

39

51

59

89

125

200

90.5

92.6

93

79

84

86

220

160

250

85.8

88.1

88.5

45

56

63

112

140

190

H

94

94.1

93.6

73

81

84

293

220

280

88.4

90.4

91

40

51

56

147

150

200

H

92.7

93.2

93

67

77

81

367

190

240

88.9

90.9

91.7

38

48

56

182

150

200

G

H

92.1

93.2

93.6

73

82

85

441

210

270

87.6

89.6

90.2

39

50

58

221

170

220

G

92.3

93.3

94.5

79

85

86

588

180

240

91.6

92.9

93

43

53

58

295

130

170

G

92.9

93.6

93.6

79

85

87

735

195

260

90

91.1

91

45

56

61

369

140

160

273

300 1200 1185 S449

95.7

900 890

39

300 1800 1785 449T 110

95.2

50

900 890

G

97

71

900 885

J

Torque Lckd Rotor (%)

Full Load

3/4

Full Load

Full Load (lb-ft)

Winding Cold Connec(Sec) tion 22

YY/ Y

12

24

YY/

12

25

YY/

18

36

YY/

14

26

YY/

14

26

YY/

14

29

YY/

17

32

YY/

19

40

YY/

19

40

YY/

20

40

YY/

Y Y Y Y Y Y Y Y Y Y 20

40

YY/

22

42

YY/

22

45

YY/

Y Y Y 23

42

YY/

28

36

YY/

20

23

YY/

Y Y Y 24

29

YY/

22

30

YY/

20

25

YY/

Y Y Y

*NEMA Design A 1.0 SF, Class F

7-8

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-9

Dimensions

44

900

H

54

54

15.5 22.5

J

46 240

885 447T

900 890

J

37 177

125

900 885

J

26 153

125 1200 1185 445T 900

K

Power Factor (%)

Typical Performance

75 1200 1185 405T

15/ 1800/ 1770/ 256T

K

5 32

60 1800 1775 364T 900

K

3

60 3600 3565 364TS

60

HIGH EFFICIENT

Modifications Accessories

Modifications Accessories

Nominal Efficiency (%)

RGZESD-1 Winding Variable Torque

Lead Time

Typical Performance

HIGH EFFICIENT

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

RGZESD / RGZZESD / RGZESDB

40 1800 1770 324T

Dimensions

Severe Duty / TEFC Multi-Speed Motors

INVERTER Duty Severe Duty

Severe & Hazardous Duty Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

460 Volts, NEMA Design C, 40ºC Ambient

460 Volts, NEMA Design B, 40ºC Ambient Current [A]

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

BreakDown (%)

Hot (Sec)

Current [A]

LR Stall Time Winding Cold Connec(Sec) tion

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

LR Stall Time BreakDown (%)

Hot (Sec)

Winding Cold Connec(Sec) tion

1/2

3/4

Full Load

1/2

3/4

Full Load

3

6.5

46

J

87.5

88.2

87.5

63

75

82

15

290

310

17

36

wye

7.5 1800 1720 213T

3.5

9.5

67

H

87

88

87.5

67

78

85

23

270

310

13

28

wye

10 1800 1710 215T

4.5 12.5

85

H

87.5

88

87.5

69

80

86

31

270

310

14

29

wye

delta

15 1800 1735 254T

7

18.5 118

G

89.5

90

89.5

70

80

85

45

250

280

18

35

wye

1/2

3/4

Full Load

1/2

3/4

Full Load

1

1800 1755 182

0.7

1.4 13

M

82.8

84.9

85.5

62

74

80

3

290

320

14

30

delta

1

1200 1160 184

1

1.6 11

K

79.5

81.6

81.5

50

64

72

4.5

250

290

19

40

delta

1.5 3600 3500 182

0.8

1.9 16

K

76.8

81

82.5

76

85

90

2.2

200

300

13

28

delta

1.5 1800 1755 184

1

2

L

84.7

86.3

86.5

62

74

81

4.5

290

320

13

29

1.5 1200 1155 184

18.5

HIGH EFFICIENT

5

1800 1730 184T

1.4

2.3 16

K

84.1

85.8

85.5

51

64

72

6.8

220

300

22

33

delta

20 1800 1740 256T

9

24

152

G

90.1

90.6

90.2

72

82

87

60

230

270

18

35

wye

2

3600 3500 184

1.1

2.5 22

K

79.1

82.7

84

73

83

89

3

230

320

15

33

delta

25 1800 1765 284T

13

29

183

G

93.3

93.6

93

72

82

87

74

220

280

19

40

delta

2

1800 1745 184

1.2

2.5 22

K

87.1

88

87.5

68

80

86

6

290

310

12

25

delta

30 1800 1765 286T

15

35

218

G

93.2

93.6

93

71

82

86

89

220

280

19

40

delta

2

1200 1170 213

1.5

2.8 22

K

84.8

86.6

86.5

59

69

77

9

200

300

21

32

delta

40 1800 1760 324T

18

49

290

G

93.5

93.6

93

73

79

82

119

240

280

19

38

delta

3

3600 3500 184

1.7

3.7 32

K

82.9

85.7

86.5

72

83

88

4.5

260

320

15

34

delta

50 1800 1760 326T

22

59

370

G

93.4

93.5

93

77

83

85

149

250

290

19

38

delta

3

1800 1760 213

1.8

4

30

J

85.6

87.4

87.5

62

74

80

9

200

280

16

35

delta

60 1800 1765 364T

31

73

440

G

93.3

93.5

93

72

80

83

179

240

270

22

45

delta

3

1200 1165 215

2.2

4.1 31

K

87.2

88.2

87.5

57

70

77

13.5

200

300

17

35

delta

75 1800 1765 365T

35

91

550

G

93.9

94.1

93.6

72

81

82

223

240

270

22

45

delta

5

3600 3515 213

3

6

46

J

85.9

87.5

87.5

76

84

89

180

280

12

26

delta

100 1800 1780 405T

32

114

725

G

94.7

94.9

94.5

81

86

87

295

210

240

22

43

delta

5

1800 1750 215

2.7

6.3 46

J

88.5

88.8

88.5

68

79

84

15

200

250

17

36

delta

125 1800 1785 444TS 44

145

840

G

93.5

94.5

94.5

78

84

86

368

220

230

20

25

delta

5

1200 1170 254U

7.5

6.6 46

J

89.7

90.2

89.5

61

73

79

22.5

170

250

14

29

delta

150 1800 1785 445TS 45

170

1085

G

94.6

95.1

95

81

86

87

441

210

220

20

30

delta

3.5

8.7 64

H

88.2

89.2

88.5

78

88

91

11

170

260

11

25

delta

200 1800 1785 447TS 67

229

1430

G

94.9

95.2

95

80

85

86

588

205

230

18

25

delta

7.5 1800 1760 254U

4

9.5 64

H

88.4

89.3

89.5

68

78

83

23

180

260

14

29

delta

7.5 1200 1170 256U

4.5

9.8 60

H

91.3

91.4

90.2

63

74

79

34

160

250

18

35

delta

10 3600 3515 254U

3

11

75

G

88.1

89.4

89.5

85

90

92

15

150

260

14

29

delta

10 1800 1760 256U

5

12

81

G

88.7

89.7

89.5

71

80

84

30

180

250

15

30

delta

10 1200 1180 284U

6

13

82

H

89.7

90.5

90.2

60

73

79

44.5

150

250

18

35

delta

15 3600 3520 256U

5

17

116

G

89.5

90.4

90.2

85

90

92

22.5

160

260

17

31

delta

15 1800 1770 284U

7

18

116

G

91.2

91.9

91.7

72

81

85

44.5

200

280

18

35

delta

15 1200 1180 324U

8

19

110

G

90.4

91.2

91

63

75

81

67

160

250

20

45

delta

20 3600 3525 286U

7.4 23

145

G

88.3

89.9

90.2

82

86

90

30

180

260

17

25

delta

20 1800 1770 286U

8

23.5 145

G

92.8

93

92.4

75

83

86

59

170

260

18

35

delta

20 1200 1175 326U

9

25

125

G

92.3

92.4

91.7

68

78

82

89

135

200

19

43

delta

25 1800 1770 324U

9

29

188

G

93

93.4

93

78

85

87

74

170

240

19

40

delta

30 1800 1775 326U 10

34

220

G

92.7

93.2

93

80

86

88

89

170

250

25

50

delta

40 1800 1780 364U 15

46

300

G

93.6

93.9

93.6

76

84

87

118

160

240

19

40

delta

50 1800 1775 365U 18

57

350

G

93.8

94

93.6

78

85

88

148

180

220

25

50

delta

60 1800 1780 405U 22

68

438

G

94.1

94.4

94.1

78

85

88

177

180

250

20

40

delta

86

543

G

94

94.3

94.1

79

85

87

220

150

210

22

45

delta

114

725

G

94.4

94.8

94.5

79

85

87

294

170

210

33

45

delta

7-10

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

75 1800 1785 444U 26 100 1800 1785 445U 34

Typical Performance

3.2

7.5 3600 3515 215

Modifications Accessories

Modifications Accessories

RGZTESD

HIGH EFFICIENT

Lead Time

Typical Performance

RGZEAD - U-Frame

INVERTER Duty Hazardous Duty

Dimensions

Severe Duty - TEFC Design C Motors

INVERTER Duty Severe Duty

Severe Duty / Automotive Duty Motors

2007 Low Voltage AC Motors Selection and Pricing Guide

7-11

INVERTER Duty Severe Duty

RGZVESD / RGZVMTESD / RGZVILESD RGZZVESD / RGZZVMTESD / RGZZVILESD

RGZVESD / RGZVMTESD / RGZVILESD RGZZVESD / RGZZVMTESD / RGZZVILESD

460 Volts, NEMA Design B, 40ºC Ambient Current [A]

1800 1745 143 1200 1160 145

1

900

1.5

13

L

1/2

3/4

78.5

81.6

Full Load

1/2

82.5

54

3/4

Full Load

Full Load (lb-ft)

67

76

3

Torque Lckd Rotor (%)

BreakDown (%)

Hot (Sec)

275

320

16

460 Volts, NEMA Design B, 40ºC Ambient

LR Stall Time Winding Cold Connec(Sec) tion 35

wye

Current [A]

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

40

3600 3530 324

12

45

290

G

92.8

Power Factor (%)

3/4

Full Load

1/2

92.9

92.4

81

3/4

Full Load

Full Load (lb-ft)

88

90

60

Torque Lckd Rotor (%)

BreakDown (%)

LR Stall Time Hot (Sec)

150

250

22

Winding Cold Connec(Sec) tion 45

delta

1

1.6

10

J

79.9

82.3

82.5

48

62

79

4.5

240

300

19

31

wye

1.2

1.9

8

H

75.1

77.4

77

43

55

64

6.1

220

260

20

40

wye

40

1800 1770 324

15

47

290

G

92.8

93

92.4

78

83

86

119

190

240

20

40

delta

1200 1180 364

24

52

290

G

92.4

92.7

92.4

60

72

78

178

170

230

29

55

delta delta

1.5 3600 3520 143

1

1.9

18

L

76.5

80.7

82.5

76

85

90

2.2

270

320

15

33

wye

40

1.5 1800 1750 145

1.3

2.2

19

L

81.5

83.6

84

55

68

76

4.5

290

320

15

32

wye

40

900

885 365

36

63

290

G

89.2

90.5

90.2

50

61

66

237

150

200

25

40

wye

50

3600 3530 326

15

55

363

G

92.9

93

92.4

83

90

92

74

150

250

18

37

delta

1800 1770 326

18

58

363

G

92.9

93

92.4

78

88

87

148

190

240

20

40

delta

1200 1180 365

30

66

363

G

92.8

93

92.4

61

72

77

223

170

230

29

55

delta delta

1.5 1200 1160 182

1.5

2.3

16

K

80.2

82.7

84

51

65

73

6.8

280

320

22

33

1.8

2.6

13

H

76.5

78.9

78.5

46

59

69

9.2

220

270

18

30

wye

2

3600 3515 145

1.1

2.5

22

K

79.4

82.9

84

75

84

89

3

260

320

15

33

wye

50

2

1800 1740 145

1.5

2.7

21

K

83.2

84.5

84

61

74

82

6

260

310

13

27

wye

50

900

885 404

28

67

363

G

90.8

90.9

90.2

65

74

77

297

140

200

25

45

wye

60

3600 3565 364

19

68

435

G

92.6

92.9

92.4

81

87

89

89

160

250

16

28

delta

1800 1775 364

21

71

435

G

92.7

92.9

92.4

75

83

86

178

160

240

22

45

delta

2

900

1200 1160 184

2 3

900

1.9

3

22

K

83.5

85

85.5

51

64

73

865 213

2.2

3.3

17

H

79

81

81.5

47

61

70

3600 3510 182

1.7

3.6

32

K

82.8

85.2

85.5

76

85

91

3

1800 1740 182

1.8

3.9

30

K

86.5

87

86.5

66

77

83

3

1200 1165 213

2.3

4

32

K

84.8

86.6

86.5

59

74

81

5

4.5 9.1 14

300

21

32

200

290

18

30

wye

60

230

320

15

34

wye

60

1200 1185 404

26

74

435

G

93

93.4

93

71

79

82

266

150

200

25

50

delta

900

885 405

30

78

435

G

90.8

90.9

90.2

68

77

80

356

140

200

30

35

delta

260

300

16

35

wye

60

210

300

17

35

wye

75

3600 3565 365

22

85

543

G

93.2

93.4

93

82

87

89

111

160

260

16

27

delta

1800 1775 365

27

87

543

G

93.3

93.5

93

75

84

86

222

155

240

22

45

delta

865 215

3.1

4.7

26

H

81

82.7

82.5

49

63

72

18

190

280

15

32

wye

3600 3490 184

1.8

5.8

46

J

85.5

86.8

86.5

83

90

93

8

260

320

12

26

wye

75

1200 1185 405

34

93

543

G

93.8

94

93.6

69

78

81

332

150

200

33

45

delta

wye

75

900

885 444

37

94

543

G

91.6

92

91.7

68

77

81

445

135

200

25

32

delta

wye

100 3600 3570 405

19

108

725

G

93.5

93.6

93

91

93

93

147

120

200

25

45

delta

wye

100 1800 1780 405

30

113

725

G

94

94.3

93.6

81

86

88

295

160

200

25

35

delta

38

117

725

G

93.7

94

93.6

76

83

86

443

140

200

30

35

delta

900

1800 1730 184 1200 1160 215

5

900

865 254

3.2 3.3 4.1

6.5 6.8 7.5

46 46 40

J J H

86.5 88 85

87.2 88.7 86

86.5 87.5 85.5

64 60 54

76 72 67

83 79 73

15 23 30

260 210 180

300 300 260

17 14 13

36 29 25

3.4

8.8

64

H

86

87

87.5

78

87

91

11

190

280

11

25

wye

7.5 1800 1750 213

4.2

9.5

64

H

88

89

88.5

66

77

84

23

210

270

14

29

wye

100

885 445

48

123

725

G

93.1

93.4

93

71

79

82

593

130

200

22

30

delta

7.5 1200 1170 254

4.5

9.8

60

H

88.9

89.2

88.5

61

75

81

34

180

250

18

35

wye

125 3600 3575 444

32

138

908

G

93.1

93.7

93.6

86

90

91

184

120

200

18

23

delta

wye

125 1800 1785 444

42

143

908

G

94.2

94.4

94.1

79

85

87

368

160

200

20

25

delta

wye

125 1200 1185 445

44

144

908

G

93.8

94

93.6

79

85

87

554

140

200

25

35

delta

wye

125

885 447

54

152

908

G

92.9

93

92.4

71

80

83

742

130

200

20

40

delta

37

164 1085

G

93.9

94.3

94.1

85

90

91

220

120

200

15

18

delta

7.5

900

865 256

10 3600 3505 215 10 1800 1750 215

6.6 11.5 4

12

5.4 12.5

64 81 81

H H H

86 88 88.5

87 88.8 89

86.5 88.5 88.5

50 81 69

62 90 80

70 88 85

46 15 30

190 190 210

260 260 270

15 14 15

30 29 30

900

900

10 1200 1165 256

5

13

75

G

90

89.8

88.5

66

76

81

45

170

250

18

35

wye

150 3600 3575 445

10

9.1 15

81

H

87.9

89.4

89.5

51

62

70

60

150

220

15

30

delta

150 1800 1785 445

45

170 1085

G

94.4

94.7

94.5

81

86

87

441

150

200

20

30

delta

45

170 1085

G

94.5

94.7

94.1

82

87

88

665

125

200

28

43

delta

900

875 284

15 3600 3530 254

5

17

116

G

86.8

88.3

88.5

85

91

93

22

190

260

17

31

wye

150 1200 1185 447

15 1800 1760 254

7.3 19

116

G

90.2

90.6

90.2

69

79

83

45

190

260

18

35

wye

150

885 447

72

186 1085

G

93

93.4

93

68

77

81

890

130

200

20

25

delta

40

216 1450

G

94

94.3

94.1

89

91

92

294

120

200

16

20

delta

900

15 1200 1175 284 10

20

116

G

89.5

90.2

89.5

58

72

78

67

160

270

20

45

delta

200 3600 3575 447

15

23

116

G

88.6

89.9

89.5

51

61

68

90

150

220

18

35

delta

200 1800 1785 447

60

225 1450

G

94.7

94.8

94.5

82

87

88

588

150

200

18

25

delta

wye

200 1200 1185 449

55

226 1450

G

94.5

94.6

94.1

83

87

88

886

125

200

25

32

delta

wye

200

101 241 1450

G

93.8

94

93.6

72

80

83

1186

125

200

15

25

delta

45

267 1825

G

94

94.3

94.1

91

93

93

368

120

200

12

18

delta

900

875 286 14

20 3600 3525 256 20 1800 1755 256

7.4 23 9.1 26

145 145

G G

86.6 90.6

88.2 90.9

88.5 90.2

84 68

88 77

92 81

30 60

180 190

260 270

17 18

25 35

900

885 449

20 1200 1175 286 12

26

145

G

90.6

90.9

90.2

63

74

80

89

160

250

19

43

delta

250 3600 3570 449

20

31

145

G

88.5

89.7

89.5

51

62

68

119

140

200

15

35

delta

250 1800 1785 449

78

281 1825

G

94.5

94.7

94.5

81

86

88

735

140

200

18

25

delta

250 1200 1185 449

75

280 1825

G

94.5

94.6

94.1

83

88

89

1108

120

200

20

25

delta

900

880 324 18

25 3600 3525 284

8

29

183

G

90.5

25 1800 1765 284 13

29

183

G

92

25 1200 1180 324 15

33

183

G

90.8

25

38

183

G

87.5

9.5 34

900

880 326 22

30 3600 3525 286

90.7

90.2

81

86

89

37

160

250

16

30

delta

92.3

91.7

73

83

91.3

91

58

70

88

74

220

280

19

40

delta

78

111

170

240

25

50

88.8

88.5

51

delta

63

70

149

150

200

22

40

delta

218

G

90.5

90.7

90.2

85

91

92

45

160

250

16

30

delta

30 1800 1765 286 15

35

218

G

91.9

92.3

91.7

73

84

88

89

220

280

19

40

delta

30 1200 1180 326 19

39

218

G

91.2

91.5

91

59

71

79

134

170

240

25

50

delta

30

47

218

G

88.4

89.8

89.5

51

63

67

178

150

200

22

40

delta

7-12

900

885 364 26

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

7-13

Dimensions

7.5 3600 3515 213

100 1200 1185 444

Typical Performance

5

12

220

75

3 5

9.1

Modifications Accessories

855 184

50

1.5

Modifications Accessories

860 182

1

Power Factor (%)

HIGH EFFICIENT

Lead Time

Lead Time

1

Typical Performance

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code 1

Dimensions

HIGH EFFICIENT

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe & Hazardous Duty P-Base (VSS) Motors

INVERTER Duty Severe Duty

Severe & Hazardous Duty P-Base (VSS) Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

460 Volts, NEMA Design B, 40ºC Ambient Current [A]

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

3/4

Power Factor (%)

Full Load

1/2

3/4

Full Load

Torque Full Lckd Load Rotor (lb-ft) (%)

Hot (Sec)

Winding Cold Connec(Sec) tion

29

183

G

90.5

90.4

91

82

88

89

37

160

250

16

30

delta

25 1800 1765 284TP

13

29

183

G

92.6

92.9

92.4

72

82

87

74

220

280

19

40

delta

25 1200 1180 324TP

15

33

183

G

92.1

92.3

91.7

58

69

77

111

170

240

25

50

delta

30 3600 3525 286TP 9.5

34

218

G

91.9

91.8

91

86

89

90

45

160

250

16

30

delta

30 1800 1765 286TP

15

35

218

G

92.6

93

92.4

72

84

88

89

220

280

19

40

delta

30 1200 1180 326TP

19

39

218

G

91.9

92.2

91.7

59

72

79

134

170

240

25

50

delta

40 3600 3530 324TP

13

46

290

G

91.3

92.1

91.7

85

89

90

60

150

250

22

45

delta

40 1800 1770 324TP

15

47

290

G

93.5

93.6

93

76

83

86

119

190

240

20

40

delta

40 1200 1180 364TP

24

52

290

G

93

93.3

93

60

71

77

178

170

230

29

55

delta

50 3600 3530 326TP

15

55

363

G

92

92.7

92.4

86

91

92

74

150

250

18

37

delta

50 1800 1770 326TP

18

58

363

G

93.4

93.5

93

78

85

87

148

190

240

20

40

delta

50 1200 1180 365TP

30

66

363

G

93.2

93.6

93

61

72

77

223

170

230

29

55

delta

60 3600 3545 364TP

19

68

435

G

93.2

93.5

93

81

87

89

89

160

250

16

28

delta

60 1800 1775 364TP

21

71

435

G

93.9

94.1

93.6

74

82

85

178

160

240

22

45

delta

60 1200 1185 404TP

27

74

435

G

94.5

94.3

93.6

75

80

81

266

165

230

25

50

delta

75 3600 3545 365TP

22

85

543

G

93.2

93.4

93

82

87

89

111

160

260

16

27

delta

75 1800 1775 365TP

27

87

543

G

94.4

94.6

94.1

74

83

85

222

155

240

22

45

delta

75 1200 1185 405TP

35

93

543

G

94.1

94.3

93.6

78

80

81

333

170

240

33

45

delta

100 1800 1780 405TP

28 114

725

G

94.7

94.9

94.5

81

86

87

295

160

200

22

43

delta

100 1200 1185 444TP

38 117

725

G

93.9

94.2

94.1

79

84

85

443

165

230

28

33

delta

125 1800 1785 444TP

43 145

908

G

93.5

94.5

94.5

78

84

86

368

160

200

26

56

delta

125 1200 1185 445TP

44 145

908

G

94.1

94.4

94.1

80

85

86

554

140

220

25

33

delta

150 1800 1785 445TP

45 170 1085

G

94.6

95.1

95

81

86

87

441

150

200

25

53

delta

150 1200 1185 447TP

45 170 1085

G

95.1

95.4

95

81

86

87

665

120

200

25

35

delta

200 1800 1785 447TP

61 225 1450

G

94.9

95.2

95

81

86

87

588

150

200

18

31

delta

200 1200 1185 449TP

60 226 1450

G

94.8

95.3

95

82

87

88

886

120

200

25

35

delta

250 1800 1785 449TP

83 281 1825

G

95

95.2

95

81

86

88

736

140

200

15

26

delta

250 1200 1185 449TP

75 280 1825

G

95.5

95.5

95

82

87

88

1108

120

200

20

25

delta

2007 Low Voltage AC Motors Selection and Pricing Guide

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

1

3600 3550 143T

0.8

2.6 15

N

84

1

1800 1775 143T

0.9

1.5 15

N

83

1

1200 1175 145T

1

1.6 12

L

1.5 3600 3550 143T

0.8

1.9 20

1.5 1800 1770 145T

1.2

2.1 20

1.5 1200 1180 182T

Power Factor (%)

Torque Lckd Rotor (%)

LR Stall Time

3/4

Full Load

Full Load (lb-ft)

69

81

41

1.5

210

390

14

20

53

65

74

3

290

480

16

20

wye

84

49

61

70

4.5

210

380

19

27

wye

86

87.5

69

79

84

2.2

230

480

19

26

wye

87

87.5

57

69

77

4.5

250

460

14

19

wye wye

Full Load

1/2

87

87.5

86

86.5

80.5

83.5

M

83

M

85

3/4

BreakDown (%)

Hot (Sec)

Winding Cold Connec(Sec) tion wye

1.4

2.4 17

K

84.5

87

87.5

49

61

67

6.7

165

410

33

50

2

3600 3550 145T

1.2

2.6 25

M

85

88

88.5

66

77

83

3

250

490

18

26

wye

2

1800 1765 145T

1.6

2.8 25

L

86

87.5

87.5

55

69

78

6

240

440

15

21

wye

2

1200 1180 184T

1.8

3

22

J

87.5

89

88.5

47

59

67

8.9

190

400

30

41

wye

3

3600 3565 182T

1.5

3.8 32

K

85.5

89

89.5

69

79

83

4.4

220

400

36

51

wye

3

1800 1770 182T

1.8

4

32

K

88.5

90

90.2

63

73

79

8.9

230

390

31

45

wye

3

1200 1180 213T

2.3

4.3 32

K

88.5

90

90.2

55

67

74

170

360

27

35

wye

5

3600 3550 184T

2.3

6.2 46

J

89

90.2

90.2

70

80

84

200

440

21

38

wye

5

1800 1770 184T

3.2

6.7 46

J

89.5

90

90.2

62

72

77

15

225

340

19

35

wye

5

1200 1180 215T

3.5

6.8 46

J

89

90.5

90.2

56

68

76

22

190

350

21

31

wye

7.5 3600 3560 213T

2.6

8.5 63

H

91

92

91.7

78

86

88

11

170

340

19

31

wye

7.5 1800 1775 213T

4

9.5 63

H

92

92.5

92.4

65

76

81

22

250

340

34

49

wye

7.5 1200 1180 254T

5

10.5 63

H

91.5

92.5

92.4

57

67

76

33

190

230

66

92

wye

10

3600 3555 215T

3.4

11.5 81

H

92

92.3

91.7

78

86

89

15

200

360

13

24

wye

10

1800 1770 215T

5.5

12.5 81

H

92

92.5

92.4

64

75

81

30

250

280

25

41

wye

10

1200 1185 256T

6.5

13.5 81

H

92

92.5

92.4

57

68

72

44

242

252

45

73

wye

15

3600 3565 254T

5

17

116

G

91

92

92.4

81

87

89

22

220

285

45

81

wye

15

1800 1780 254T

7.3

19

116

G

92.5

93.5

93

66

76

79

44

198

253

25

55

wye

20

3600 3560 256T

5.5

23

145

G

92

92.5

92.4

84

88

88

30

210

250

34

75

wye

20

1800 1780 256T

9.5

25

145

G

93

93.5

93.6

68

78

80

59

187

230

28

56

wye

13 7.4

2007 Low Voltage AC Motors Selection and Pricing Guide

7-15

Dimensions

8

Current [A]

Typical Performance

25 3600 3525 284TP

7-14

NEMA PREMIUM® EFFICIENT

460 Volts, NEMA Design B, 40ºC Ambient

LR Stall Time BreakDown (%)

GP100A / GP100 / SD100

Modifications Accessories

Modifications Accessories

HIGH EFFICIENT

Lead Time

Typical Performance

HSRGZVESD

INVERTER Duty Hazardous Duty

Dimensions

General Purpose & Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty P-Base (VHS) Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Current [A]

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

3/4

Full Load

NEMA PREMIUM® EFFICIENT

460 Volts, NEMA Design B (except as noted), 40ºC Ambient

Power Factor (%)

1/2

3/4

Full Load

Torque Full Lckd Load Rotor (lb-ft) (%)

LR Stall Time BreakDown (%)

Hot (Sec)

Current [A]

Winding Cold Connec(Sec) tion

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

Full Load

Power Factor (%) Full Load (lb-ft)

Torque Lckd Rotor (%)

LR Stall Time BreakDown (%)

Hot (Sec)

Winding Cold Connec(Sec) tion

1/2

3/4

1/2

3/4

Full Load

1

3600 3495 143T

0.6

1.3

11

K

78.7

81.9

82.5

71

82

88

1.5

230

360

18

38

wye

75

3600 3565 365TS 22

85

543

G

93.7

94.3

94.1

81

86

88

111

160

260

16

27

delta

1

1800 1760 143T

1

1.5

12

L

82

84.8

85.5

52

65

73

3

275

400

16

34

wye

75

1800 1780 365T

25

85

543

G

95.6

95.8

95.4

78

85

87

221

180

240

25

35

delta

1

1200 1160 145T

1

1.6

11

K

79.4

82.2

82.5

48

61

69

4.5

220

310

22

38

wye

75

1200 1185 405T

34

93

543

G

94.7

94.9

94.5

68

77

80

332

180

220

33

45

delta

1.5 3600 3495 143T

0.9

1.9

17

L

83

85.3

85.5

73

83

88

2.3

270

400

16

36

wye

100 3600 3570 405TS 19

108

725

G

94.6

94.7

94.1

90

92

92

147

120

200

25

45

delta

1.5 1800 1755 145T

1.4

2.2

19

L

83.8

86.2

86.5

53

66

74

4.5

260

400

16

35

wye

100 1800 1780 405T

30

113

725

G

95.8

96

95.4

80

86

87

295

180

200

25

35

delta

1.5 1200 1175 182T

20

M

83.3

86.3

87.5

49

62

70

6.7

290

460

20

38

wye

100 1200 1185 444T

39

117

725

G

95.1

95.3

95

73

81

84

443

160

200

30

35

delta

1.1

2.4

23

L

84.4

86.4

86.5

74

85

90

3

280

400

16

37

wye

125 3600 3575 444TS 32

138

908

G

94.5

95.1

95

84

88

89

184

120

200

18

23

delta

2

1800 1755 145T

1.6

2.8

22

K

84

86.4

86.5

56

69

77

6

260

380

16

33

wye

125 1800 1785 444T

45

143

908

G

95.4

95.6

95.4

78

84

86

368

160

200

20

25

delta

2

1200 1175 184T

1.6

2.9

24

L

86

88.1

88.5

55

67

74

8.9

280

440

18

38

wye

125 1200 1185 445T

48

144

908

G

95.1

95.4

95

74

82

85

554

160

200

25

35

delta

3

3600 3505 182T

1.6

3.6

32

K

84.3

86.5

86.5

77

88

90

4.5

280

360

15

34

wye

150 3600 3575 445TS 37

164 1085

G

94.8

95.2

95

84

89

90

220

120

200

15

18

delta

3

1800 1770 182T

2

4

32

K

86.9

89

89.5

59

72

79

9

260

320

17

35

wye

150 1800 1785 445T

52

170 1085

G

95.7

96

95.8

78

84

86

441

150

200

20

30

delta

3

1200 1180 213T

2.4

4.3

32

K

86.5

89

89.5

54

66

73

13

5

3600 3485 184T

1.8

5.7

46

J

88

89.1

88.5

83

89

92

5

1800 1765 184T

3

6.4

46

J

88.9

89.9

89.5

65

76

82

5

1200 1175 215T

3.8

6.9

46

J

87.8

89.2

89.5

56

68

7.5 3600 3535 213T

2.9

8.6

64

H

88.7

90.4

89.5

78

7.5 1800 1770 213T

4.3

9.5

64

H

90.2

91.6

91.7

66

7.5 1200 1180 254T

5.9 10.5

64

H

89.3

90.9

91

55

67

75

33

160

260

19

10 3600 3520 215T

3.3 11.4

81

H

89.7

90.7

90.2

81

88

91

15

220

290

14

10 1800 1770 215T

5.5 12.5

81

H

91.3

92.1

91.7

66

77

82

30

210

290

20

10 1200 1180 256T

7

13.8

81

H

89.9

91.2

91

56

68

75

45

170

260

15 3600 3530 254T

5

17

116

G

89.5

91.1

91

83

89

91

22

190

260

15 1800 1770 254T

8

19

116

G

92

92.6

92.4

67

77

81

45

200

260

19

15 1200 1180 284T 11

21

116

G

90.9

91.8

91.7

53

66

90

67

150

240

22

20 3600 3525 256T

7.4 23

145

G

90.3

91.2

91

81

87

90

30

180

260

17

20 1800 1770 256T

9.5 24

145

G

93.1

93.3

93

69

79

83

59

200

270

250

300

18

36

wye

150 1200 1190 447T

59

172 1085

G

95.6

96

95.8

73

82

85

662

140

200

28

43

delta

260

320

14

30

wye

200 3600 3575 447TS 44

216 1450

G

95.3

95.6

95.4

88

90

91

294

120

200

16

20

delta

15

260

320

18

35

wye

200 1800 1785 447T

70

226 1450

G

96.2

96.5

96.2

76

84

86

588

160

200

18

25

delta

75

22

220

320

17

35

wye

200 1200 1190 449T

73

227 1450

G

95.6

96.2

95.8

75

83

86

883

125

200

25

32

delta

87

91

11

220

320

12

20

wye

250 3600 3575 449TS 45

265 1825

G

95.7

96

95.8

89

91

91

368

120

200

12

18

delta

76

81

21

210

290

21

39

wye

250 1800 1785 449T

90

278 2100 H *

96.1

96.3

96.2

78

85

87

735

140

200

18

25

delta

42

wye

250 1200 1190 449T

86

281 2050 H *

95.7

96

95.8

81

86

87

1104

120

200

20

25

delta

29

wye

300 3600 3570 449TS 68

325 2200

95.2

95.8

95.8

86

90

91

441

100

200

12

13

delta

38

wye

300 1800 1785 449T 114 338 2400 H *

96.1

96.3

96.2

75

83

86

882

140

200

22

30

delta

20

44

wye

300 1200 1185 S449 119 340 2400 H *

96

96.1

95.8

82

85

86

1329

105

200

26

33

delta

17

31

wye

350 3600 3570 S449SS 68

95.8

96.1

95.8

89

91

92

515

80

200

20

26

delta

40

wye

350 1800 1785 S449 115 390 2550

G

95.8

96.3

96.2

77

84

86

1029

100

200

25

32

delta

48

delta

400 3600 3570 S449SS 80

420 2900

G

94.6

96.1

95.8

89

92

93

588

80

200

17

24

delta

25

wye

400 1800 1785 S449 130 445 2900

G

96

96.4

96.2

77

84

86

1176

100

200

21

26

delta

20

42

wye delta

7.5

20 1200 1180 286T 13

27

145

G

91.2

92

91.7

57

69

93

89

150

240

20

45

25 3600 3525 284TS

8

29

183

G

92

92.2

91.7

80

85

88

37

160

250

16

30

delta

25 1800 1775 284T 11

30

183

G

93.5

94

93.6

71

80

84

74

180

250

24

44

delta

25 1200 1185 324T 14

33

183

G

92.7

93.2

93

62

72

76

111

170

240

28

54

delta

9.5 34

218

G

92

92.2

91.7

84

89

90

45

160

250

16

30

delta

218

G

93.9

94.1

93.6

73

82

85

89

180

250

24

44

delta delta

30 3600 3525 286TS

30 1800 1775 286T 12

35

30 1200 1185 326T 15

39

218

G

93.1

93.5

93

64

73

77

133

170

220

26

52

40 3600 3535 324TS 12

45

290

G

94

94.1

93.6

80

87

89

60

150

250

22

45

delta

40 1800 1780 324T 15

46

290

G

94

94.3

94.1

75

83

86

118

180

230

22

45

delta delta

40 1200 1185 365T 18

49

290

G

94

94.4

94.1

70

79

81

177

190

220

29

55

50 3600 3535 326TS 15

55

363

G

94.1

94.2

93.6

82

89

91

74

150

250

18

37

delta

50 1800 1780 326T 19

58

363

G

94.8

95

94.5

74

82

85

148

170

230

22

45

delta

50 1200 1185 365T 24

62

363

G

94

94.3

94.1

67

76

80

222

190

220

29

55

delta

60 3600 3565 364TS 19

68

435

G

93.8

94.1

93.6

80

86

88

89

160

250

16

28

delta

60 1800 1780 364T 21

68

435

G

95.2

95.4

95

77

85

87

177

180

240

26

38

delta

60 1200 1185 404T 28

74

435

G

94.2

94.7

94.5

65

76

80

266

180

220

25

50

delta

7-16

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

370 2550

G

G

*NEMA Design A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-17

Dimensions

2.3

3600 3495 145T

Typical Performance

1.5

2

Modifications Accessories

Modifications Accessories

460 Volts, NEMA Design B (except as noted), 40ºC Ambient

RGZEESD

Lead Time

Typical Performance

NEMA PREMIUM® EFFICIENT

INVERTER Duty Hazardous Duty

Dimensions

RGZEESD

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

460 Volts, NEMA Design B (except as noted), 40ºC Ambient

460 Volts, NEMA Design B, 40ºC Ambient Current [A]

Current [A]

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code 1/2

3/4

NEMA PREMIUM® EFFICIENT

Power Factor (%)

Full Load

Min. Guar.

1/2

3/4

Full Load

Torque Full Lckd BreakLoad Rotor Down (lb-ft) (%) (%)

LR Stall Time Hot (Sec)

Winding Cold Connec(Sec) tion

Nominal Efficiency (%)

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

1/2

1

3600 3495 143T

0.6

1.3

11

K

78.7

Power Factor (%)

3/4

Full Load

Min. Guar.

1/2

Full Full Load 3/4 Load (lb-ft)

81.9

82.5

80

71

82

88

1.5

Torque Lckd Rotor (%) 230

LR Stall Time BreakDown (%)

Hot (Sec)

360

18

Winding Cold Connec(Sec) tion 38

wye

1

3600 3550 143T

0.8

2.6

15

N

84

87

87.5

86.5

69

81

41

1.5

210

390

14

20

wye

1

1800 1760 143T

1

1.5

12

L

82

84.8

85.5

82.5

52

65

73

3

275

400

16

34

wye

1

1800 1775 143T

0.9

1.5

15

N

83

86

86.5

85.5

53

65

74

3

290

480

16

20

wye

1

1200 1160 145T

1

1.6

11

K

79.4

82.2

82.5

80

48

61

69

4.5

220

310

22

38

wye

1

1200 1175 145T

1

1.6

12

L

80.5

83.5

84

82.5

49

61

70

4.5

210

380

19

27

wye

860 182T

1.3

1.9

8

H

72.1

75

78.5

75.5

43

56

65

6.1

200

260

20

40

wye

870 182T

1.5

2.1

9

J

77

80

81.5

80

36

47

56

6

140

245

50

68

wye

1.5 3600 3495 143T

0.9

1.9

17

L

83

85.3

85.5

82.5

73

83

88

2.3

270

400

16

36

wye

1.5 3600 3550 143T

0.8

1.9

20

M

83

86

87.5

86.5

69

79

84

2.2

230

480

19

26

wye

1.5 1800 1755 145T

1.4

2.2

19

L

83.8

86.2

86.5

84

53

66

74

4.5

260

400

16

35

wye

1.5 1800 1770 145T

1.2

2.1

20

M

85

87

87.5

86.5

57

69

77

4.5

250

460

14

19

wye

1.5 1200 1175 182T

1.5

2.3

20

M

83.3

86.3

87.5

85.5

49

62

70

6.7

290

460

20

38

wye

1.5 1200 1180 182T

1.4

2.4

17

K

84.5

87

87.5

86.5

49

61

67

6.7

165

410

33

50

wye

1.5

2

2.8

13

H

78

80.4

80

77

42

54

63

9.2

230

300

19

31

wye

1.5

865 184T

2.3

3

17

H

78.5

82

82.5

81.5

35

47

55

9.1

130

235

43

63

wye

2

3600 3495 145T

1.1

2.4

23

L

84.4

86.4

86.5

84

74

85

90

3

280

400

16

37

wye

2

3600 3550 145T

1.2

2.6

25

M

85

88

88.5

87.5

66

77

83

3

250

490

18

26

wye

2

1800 1755 145T

1.6

2.8

22

K

84

86.4

86.5

84

56

69

77

6

260

380

16

33

wye

2

1800 1765 145T

1.6

2.8

25

L

86

87.5

87.5

86.5

55

69

78

6

240

440

15

21

wye

2

1200 1175 184T

1.6

2.9

24

L

86

88.1

88.5

86.5

55

67

74

8.9

280

440

18

38

wye

2

1200 1180 184T

1

900

900

1

900

900

860 184T

3

22

J

87.5

89

88.5

81.5

47

59

67

8.9

190

400

30

41

wye

2

870 213T

2.2

3.2

17

H

82.8

84.3

84

81.5

46

60

70

200

290

18

30

wye

2.1

3.3

16

H

84

84.5

84

82.5

46

59

68

12.1

175

260

22

38

wye

3

3600 3505 182T

1.6

3.6

32

K

84.3

86.5

86.5

84

77

88

90

4.5

280

360

15

34

wye

3

3600 3565 182T

1.5

3.8

32

K

85.5

89

89.5

88.5

69

79

83

4.4

220

400

36

51

wye

3

1800 1770 182T

2

4

32

K

86.9

89

89.5

87.5

59

72

79

9

260

320

17

35

wye

3

1800 1770 182T

1.8

4

32

K

88.5

90

90.2

89.5

63

73

79

8.9

230

390

31

45

wye

3

1200 1180 213T

wye

3

1200 1180 213T

2.3

4.3

32

K

88.5

90

90.2

89.5

55

67

74

13

170

360

27

35

wye

3

4.8

25

H

85.5

86.5

85.5

84

45

59

68

18

195

270

19

31

wye

200

440

21

38

wye

225

340

19

35

wye

900

3

900

870 215T

5

3600 3550 184T

2.3

6.2

46

J

89

90.2

90.2

89.5

70

80

84

5

1800 1770 184T

3.2

6.7

46

J

89.5

90

90.2

89.5

62

72

77

5

1200 1180 215T

7.4 15

6.8

46

J

89

90.5

90.2

89.5

56

68

76

22

190

350

21

31

wye

5.5

8.8

33

F

85.5

87

86.5

85.5

43

54

62

30

155

210

65

115

wye

7.5 3600 3560 213T

2.6

8.5

63

H

91

92

91.7

91

78

86

88

11

170

340

19

31

wye

7.5 1800 1775 213T

4

9.5

63

H

92

92.5

92.4

91.7

65

76

81

22

250

340

34

49

wye

7.5 1200 1180 254T

5

10.5

63

H

91.5

92.5

92.4

91

57

67

76

33

190

230

66

92

wye

7.5

7.9 13

50

G

87

88

87.5

86.5

44

55

62

45

165

200

50

100

wye

10 3600 3555 215T

3.4 11.5

81

H

92

92.3

91.7

91

78

86

89

15

200

360

13

24

wye

10 1800 1770 215T

5.5 12.5

81

H

92

92.5

92.4

91.7

64

75

81

30

250

280

25

41

wye

10 1200 1185 256T

6.5 13.5

81

H

92

92.5

92.4

91

57

68

72

44

242

252

45

73

wye

15 3600 3565 254T

5

17

116

G

91

92

92.4

91.7

81

87

89

22

220

285

45

81

wye

15 1800 1780 254T

7.3 19

116

G

92.5

93.5

93

92.4

66

76

79

44

198

253

25

55

wye

20 3600 3560 256T

5.5 23

145

G

92

92.5

92.4

91.7

84

88

88

30

210

250

34

75

wye

20 1800 1780 256T

9.5 25

145

G

93

93.5

93.6

93

68

78

80

59

187

230

28

56

wye

900

900

875 256T

2.4

4.3

32

K

86.5

89

89.5

87.5

54

66

73

13

250

300

18

36

865 215T

2.5

4.5

26

H

86

86.5

85.5

82.5

51

64

73

18

190

280

16

32

wye

5

3600 3485 184T

1.8

5.7

46

J

88

89.1

88.5

86.5

83

89

92

260

320

14

30

wye

5

1800 1765 184T

3

6.4

46

J

88.9

89.9

89.5

87.5

65

76

82

15

260

320

18

35

wye

5

1200 1175 215T

3.8

6.9

46

J

87.8

89.2

89.5

87.5

56

68

75

22

220

320

17

35

wye

865 254T

4.1

7.5

40

H

86

87

86.5

84

53

66

72

30

180

260

13

25

wye

7.5 3600 3535 213T

2.9

8.6

64

H

88.7

90.4

89.5

87.5

78

87

91

11

220

320

12

20

wye

7.5 1800 1770 213T

4.3

9.5

64

H

90.2

91.6

91.7

90.2

66

76

81

21

210

290

21

39

wye

7.5 1200 1180 254T

5.9 10.5

64

H

89.3

90.9

91

89.5

55

67

75

33

160

260

19

42

wye

7.5

6.6 12

64

H

90.6

90.9

90.2

88.5

59

72

78

34

180

250

15

30

wye

10 3600 3520 215T

3.3 11.4

81

H

89.7

90.7

90.2

88.5

81

88

91

15

220

290

14

29

wye

10 1800 1770 215T

5.5 12.5

81

H

91.3

92.1

91.7

90.2

66

77

82

30

210

290

20

38

wye

10 1200 1180 256T

7

81

H

89.9

91.2

91

89.5

56

68

75

45

170

260

20

44

wye

10

9.1 15

81

H

87.9

89.7

90.2

88.5

49

61

69

60

150

220

15

30

delta wye

3

5

900

900

900

900

865 256T

875 284T

5

17

116

G

89.5

91.1

91

89.5

83

89

91

22

190

260

17

31

15 1800 1770 254T

8

19

116

G

92

92.6

92.4

91

67

77

81

45

200

260

19

40

wye

15 1200 1180 284T 11

21

116

G

90.9

91.8

91.7

90.2

53

66

90

67

150

240

22

48

delta

15

23

116

G

88.7

90

90.2

88.5

48

60

67

90

150

220

18

35

delta

20 3600 3525 256T

7.4 23

145

G

90.3

91.2

91

89.5

81

87

90

30

180

260

17

25

wye

20 1800 1770 256T

9.5 24

145

G

93.1

93.3

93

91.7

69

79

83

59

200

270

20

42

wye

145

G

91.2

92

91.7

90.2

57

69

93

89

150

240

20

45

delta delta

20

2007 Low Voltage AC Motors Selection and Pricing Guide

13.8

7.5

15 3600 3530 254T

900

875 286T 14

20 1200 1180 286T 13

7-18

12

900

27

880 324T 18

31

145

G

89.8

91.1

91

89.5

50

61

67 119

140

200

15

35

25 3600 3525 284TS 8

29

183

G

92

92.2

91.7

90.2

80

85

88

37

160

250

16

30

delta

25 1800 1775 284T 11

30

183

G

93.5

94

93.6

92.4

71

80

84

74

180

250

24

44

delta

25 1200 1185 324T 14

33

183

G

92.7

93.2

93

91.7

62

72

76 111

170

240

28

54

delta

25

delta

41

183

G

89.2

90.5

90.2

88.5

47

57

63 149

150

200

22

40

30 3600 3525 286TS 9.5 34

900

218

G

92

92.2

91.7

90.2

84

89

90

45

160

250

16

30

delta

30 1800 1775 286T 12

35

218

G

93.9

94.1

93.6

92.4

73

82

85

89

180

250

24

44

delta

30 1200 1185 326T 15

39

218

G

93.1

93.5

93

91.7

64

73

77 133

170

220

26

52

delta

30

47

218

G

90.6

92

91.7

90.2

49

61

65 178

150

200

22

40

delta

900

880 326T 24

885 364T 26

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-19

Dimensions

3.5

875 254T

5

900

Typical Performance

1.8

870 213T

2

Modifications Accessories

Modifications Accessories

RGZEESDX

NEMA PREMIUM® EFFICIENT

Lead Time

Typical Performance

SD100 IEEE841

INVERTER Duty Hazardous Duty

Dimensions

Severe Duty / IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty / IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

460 Volts, 40ºC Ambient

460 Volts, NEMA Design B (except as noted), 40ºC Ambient Current [A]

Nominal Efficiency (%)

INVERTER DUTY

3/4

Full Load

1/2

Torque Full Lckd Full Load Rotor 3/4 Load (lb-ft) (%)

40 3600 3535 324TS 12 40 1800 1780 324T 15

45 46

290 290

G G

94 94

94.1 94.3

93.6 94.1

92.4 93

80 75

87 83

89 86

60 118

150 180

250 230

22 22

45 45

delta delta

1

1800

143T

10:1

1745

1.5

1.1

82.5

3

1.5

3490

0.071

7.33

8.02 306

1

1200

145T

10:1

1140

1.8

1.3

80

4.6

2.3

2280

0.053

7.47

6.54 214

40 1200 1185 365T

18

49

290

G

94

94.4

94.1

93

70

79

81

177

190

220

29

55

delta

1

900

182T

10:1

860

1.9

1.2

78.5

6.1

3.1

1760

0.03

40

kVA/ Synch F.L. No Full Lckd HP HP RPM RPM Frame Load Load Rotor Code

900 885 365T

1/2

Min. Guar.

Power Factor (%)

LR Stall Time BreakDown (%)

Hot (Sec)

Winding Cold Connec(Sec) tion

HP

Synch RPM Frame

Speed Range

F.L. RPM

FL Amps

NL Amps

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

12.28 17.15 297

9.45 12.5

5.85 8.68

15.68 12.28

36

63

290

G

90.7

92

91.7

90.2

49

60

65

237

150

200

25

40

delta

1.5

3600

143T

10:1

3485

2

0.9

82.5

2.3

1.2

5225

0.11

6.87

3.18 372

6.4

4.52

50 3600 3535 326TS 15

55

363

G

94.1

94.2

93.6

92.4

82

89

91

74

150

250

18

37

delta

1.5

1800

145T

10:1

1740

2.2

1.4

84

4.5

2.3

3480

0.103

4.94

5.27 199

6.98

4.37

50 1800 1780 326T

19

58

363

G

94.8

95

94.5

93.6

74

82

85

148

170

230

22

45

delta

1.5

1200

182T

10:1

1160

2.3

1.5

85.5

6.8

3.4

2320

0.104

5.22

9.4

6.28

4.54

50 1200 1185 365T

24

62

363

G

94

94.3

94.1

93

67

76

80

222

190

220

29

55

delta

1.5

900

184T

10:1

860

2.6

1.8

80

9.2

4.6

1760

0.09

8.31 12.02 202

8.31 12.08

50

28

67

363

G

93

93.1

92.4

91

64

73

76

297

140

200

25

40

delta

2

3600

145T

10:1

3495

2.5

1.1

84

3

1.5

5240

0.146

4.87

2.45 286

4.59

60 3600 3565 364TS 19

68

435

G

93.8

94.1

93.6

92.4

80

86

88

89

160

250

16

28

delta

2

1800

145T

10:1

1735

2.9

1.9

84

6.1

3

3470

0.146

3.8

4.16 165

5.05

3.56

60 1800 1780 364T

21

68

435

G

95.2

95.4

95

94.1

77

85

87

177

180

240

26

38

delta

2

1200

184T

10:1

1160

3

1.9

86.5

9.1

4.5

2320

0.139

3.59

7.37 145

4.26

3.43

60 1200 1185 404T

28

74

435

G

94.2

94.7

94.5

93.6

65

76

80

266

180

220

25

50

delta

2

900

213T

10:1

865

3.3

2.2

82.5

60

30

78

435

G

93

93.1

92.4

91

66

75

78

356

140

200

30

35

delta

3

3600

182T

10:1

3510

3.6

1.7

86.5

75 3600 3565 365TS 22

85

543

G

93.7

94.3

94.1

93

81

86

88

111

160

260

16

27

delta

3

1800

182T

10:1

1740

3.9

1.8

87.5

75 1800 1780 365T

25

85

543

G

95.6

95.8

95.4

94.5

78

85

87

221

180

240

25

35

delta

3

1200

213T

10:1

1165

4

2.3

87.5

14

75 1200 1185 405T

34

93

543

G

94.7

94.9

94.5

93.6

68

77

80

332

180

220

33

45

delta

3

900

215T

10:1

865

4.7

3.1

84

18

75

37

94

543

G

93.5

93.9

93.6

92.4

67

76

80

445

135

200

25

32

delta

5

3600

184T

10:1

3490

5.8

1.8

87.5

100 3600 3570 405TS 19

108 725

G

94.6

94.7

94.1

93

90

92

92

147

120

200

25

45

delta

5

1800

184T

10:1

1730

6.5

3.2

87.5

100 1800 1780 405T

30

113 725

G

95.8

96

95.4

94.5

80

86

87

295

180

200

25

35

delta

5

1200

215T

10:1

1160

6.8

3.3

88.5

100 1200 1185 444T

39

117 725

G

95.1

95.3

95

94.1

73

81

84

443

160

200

30

35

delta

5

900

254T

6:1

865

7.5

4.1

100 900 885 445T

48

123 725

G

94.2

94.5

94.1

93

70

78

81

593

130

200

22

30

delta

7.5

3600

213T

10:1

3515

8.8

3.4

125 3600 3575 444TS 32

138 908

G

94.5

95.1

95

94.1

84

88

89

184

120

200

18

23

delta

7.5

1800

213T

10:1

1750

9.5

4.2

125 1800 1785 444T

45

143 908

G

95.4

95.6

95.4

94.5

78

84

86

368

160

200

20

25

delta

7.5

1200

254T

6:1

1170

9.8

4.5

125 1200 1185 445T

48

144 908

G

95.1

95.4

95

94.1

74

82

85

554

160

200

25

35

delta

7.5

900

256T

6:1

865

12

125 900 885 447T

54

152 908

G

94.6

94.7

94.1

93

70

79

82

742

130

200

20

30

delta

10

3600

215T

10:1

3505

150 3600 3575 445TS 37

164 1085

G

94.8

95.2

95

94.1

84

89

90

220

120

200

15

18

delta

10

1800

215T

10:1

150 1800 1785 445T

52

170 1085

G

95.7

96

95.8

95

78

84

86

441

150

200

20

30

delta

10

1200

256T

150 1200 1190 447T

59

172 1085

G

95.6

96

95.8

95

73

82

85

662

140

200

28

43

delta

10

900

284T

150 900 885 449T

61

180 1085

G

94.3

94.5

94.1

93

72

80

83

890

130

200

20

25

delta

15

3600

200 3600 3575 447TS 44

216 1450

G

95.3

95.6

95.4

94.5

88

90

91

294

120

200

16

20

delta

15

200 1800 1785 447T

70

226 1450

G

96.2

96.5

96.2

95.4

76

84

86

588

160

200

18

25

delta

15

200 1200 1190 449T

73

227 1450

G

95.6

96.2

95.8

95

75

83

86

883

125

200

25

32

delta

200 900 885 S449

900 885 404T

900 885 405T

900 885 444T

3.56

0.13

7.53

6.74 147

7.46

5.13

5265

0.231

4.34

2.21 193

2.84

2.02

9.1

4.5

3480

0.208

2.98

4.54 146

3.13

2.62

6.8

2330

0.23

3.24

4.57 130

3.25

1.73

9

1765

0.19

5.66

5.287 118

5.23

3.87

3.8

5235

0.36

2.62

1.54 135

1.86

1.4

15

7.6

3460

0.31

1.71

2.7

84.2

1.85

1.64

23

11.3

2320

0.34

2.01

2.91

86.8

1.99

1.23

86.5

30

15

1765

0.66

4.09

4.8

68.4

1.46

1.99

88.5

11

7.5

5270

0.59

2.08

1.46

83.6

1.2

0.71

89.5

23

11.3

3500

0.56

1.27

2.48

63.2

1.03

0.75

90.2

34

16.8

2340

1.09

1.66

1.89

54.3

0.82

0.58

6.6

87.5

46

23

1765

1

3

3.69

56.1

0.91

1.47

12

4

89.5

15

10

5255

0.76

1.67

1.27

74

0.97

0.6

1750

13

5.4

89.5

30

15

3500

0.74

0.99

1.98

49.6

0.82

0.61

6:1

1165

13

90.2

45

22.5

2330

1.42

1.41

1.71

52.1

0.68

0.53

6:1

875

15

9.1

91

60

36

1475

1.4

2.02

2.44

34.6

0.65

0.49

254T

6:1

3530

17

5

90.2

22

15

5295

2.25

1.33

1.03

57.6

0.390 0.310

1800

254T

6:1

1760

19

7.3

91.7

45

22.4

3520

2.2

0.85

1.61

38.5

0.380 0.340

1200

284T

6:1

1175

20

10

91

67

40

1955

2.2

1

1.11

26.3

0.400 0.240

15

900

286T

6:1

875

23

14

91

90

54

1475

2.1

1.34

1.68

23.8

0.380 0.330

7.5

78

240 1450

G

95

95

94.5

93.6

71

79

83

1187

125

200

15

25

delta

20

3600

256T

6:1

3525

23

7.4

90.2

30

19.9

5285

3

0.95

0.8

40.3

0.300 0.270

250 3600 3575 449TS 45

265 1825

G

95.7

96

95.8

95

89

91

91

368

120

200

12

18

delta

20

1800

256T

6:1

1755

26

9.1

91.7

60

29.9

3510

2.9

0.6

1.26

30.7

0.260 0.260

250 1800 1785 449T

90

278 2100 H *

96.1

96.3

96.2

95.4

78

85

87

735

140

200

18

25

delta

20

1200

286T

6:1

1175

26

12

91.7

89

54

1955

3

0.77

0.93

22.9

0.290 0.210

250 1200 1190 449T

86

281 2050 H *

95.7

96

95.8

95

81

86

87

1104

120

200

20

25

delta

20

900

324T

4:1

860

31

18

91

119

71

1480

4.6

1.15

1.68

14.8

0.230 0.193

250 900 885 S449 109

303 1825

G

94.5

94.8

94.5

93.6

70

78

82

1483

105

200

25

32

delta

25

3600 284TS

6:1

3525

29

8

24.9

4700

3.7

0.55

1.14

38.5

0.270 0.210

300 3600 3570 449TS 68

325 2200

G

95.2

95.8

95.8

95

86

90

91

441

100

200

12

13

delta

25

1800

284T

6:1

1765

29

13

93

49.7

2940

3.8

0.55

0.88

22.8

0.190 0.180

300 1800 1785 S449 114

338 2400 H *

96.1

96.3

96.2

95.4

75

83

86

882

140

200

22

30

delta

25

1200

324T

4:1

1180

33

15

92.4

111

67

1965

5.9

0.67

0.65

16.1

0.170 0.150

300 1200 1185 S449 119

340 2400 H *

96

96.1

95.8

95

82

85

86

1329

105

200

26

33

delta

25

900

326T

4:1

880

38

22

90.2

149

350 3600 3570 S449SS 68

370 2550

95.8

96.1

95.8

95

89

91

92

515

80

200

20

26

delta

30

3600 286TS

6:1

3525

34

10

91.7

45

G

91.7

37 74

89

1480

7

0.95

1.41

12.6

0.174 0.159

29.8

4700

4.5

0.42

0.98

33.8

0.200 0.170

350 1800 1785 S449 115

390 2550

G

95.8

96.3

96.2

95.4

77

84

86

1029

100

200

25

32

delta

30

1800

286T

6:1

1765

35

15

93

59.6

2940

4.5

0.44

0.75

20.3

0.150 0.150

400 3600 3570 S449SS 80

420 2900

G

94.6

96.1

95.8

95

89

92

93

588

80

200

21

26

delta

30

1200

326T

4:1

1180

39

19

92.4

134

80

1965

7.1

0.56

0.56

13.9

0.150 0.130

30

900

364T

4:1

885

47

26

91

178

119

1335

7.1

0.77

1.15

89

9.65 0.144 0.083

*NEMA Design A Efficiency values are shown for 60 hertz sine wave power.

7-20

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

7-21

Dimensions

1765

2.3

Typical Performance

6

4.5

10

12

185

Modifications Accessories

Modifications Accessories

RGZESDI - Variable Torque / Constant Torque

NEMA PREMIUM® EFFICIENT

Lead Time

Typical Performance

RGZEESDX

INVERTER Duty Hazardous Duty

Dimensions

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty / IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

460 Volts, 40ºC Ambient Speed Range

F.L. RPM

FL Amps

NL Amps

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

RGZESDI - 10:1 Constant Torque

INVERTER DUTY

460 Volts, 40ºC Ambient Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

HP

Synch RPM Frame

40

3600

324TS

6:1

3530

45

12

93.6

60

47.7

4705

9.4

0.33

0.6

22.6

0.088 0.100

1

1800

143T

10:1

1745

1.5

1.1

82.5

3

1.5

3490

0.07

7.33

8.02 306

40

1800

324T

4:1

1770

47

15

93.6

119

79.2

2940

9.5

0.38

0.67 18.5

0.110 0.100

1

1200

145T

10:1

1140

1.8

1.3

80

4.6

2.3

2280

0.05

7.47

6.54 214

40

1200

364T

4:1

1180

52

24

93.6

178

119

1770

9.5

0.41

0.7

11.6

0.100 0.070

1

900

182T

10:1

890

1.9

1.2

78.5

6.1

3.1

1760

0.09

158

HP

Synch RPM Frame

Speed Range

F.L. RPM

FL Amps

NL Amps

12.28 17.15 297

9.45 12.5

5.85 8.68

15.68 12.28

40

900

365T

4:1

885

63

36

91.7

237

1335

9.5

0.56

0.87

7.2

0.094 0.061

1.5

3600

143T

10:1

3485

2

0.9

82.5

2.3

1.2

5225

0.11

6.87

3.18 372

6.4

50

3600

326TS

4:1

3530

55

15

93.6

74

59.6

4705

11.8

0.25

0.49 18.8

0.072 0.083

1.5

1800

145T

10:1

1740

2.2

1.4

84

4.5

2.3

3480

0.10

4.94

5.27 199

6.98

4.37

50

1800

326T

4:1

1770

58

18

93.6

148

98.9

2950

11.9

0.31

0.54 15.8

0.082 0.082

1.5

1200

182T

10:1

1160

2.3

1.5

85.5

6.8

3.4

2320

0.10

5.22

9.4

6.28

4.54

50

1200

365T

4:1

1180

66

30

93.6

223

148

1770

11.9

0.32

0.58 10.4

0.081 0.058

1.5

900

184T

10:1

860

2.6

1.8

80

9.2

4.6

1760

0.09

8.31 12.02 202

8.31 12.08

50

900

404T

4:1

880

67

28

91.7

297

198

1330

11.6

0.49

0.82 10.2

0.079 0.071

2

3600

145T

10:1

3495

2.5

1.1

84

3

1.5

5240

0.15

4.87

2.45 286

4.59

3.56

60

3600

364TS

4:1

3565

68

19

93.6

89

89

4455

14.6

0.30

0.56 14.8

0.066 0.054

2

1800

145T

10:1

1735

2.9

1.9

84

6.1

3

3470

0.13

3.8

4.16 165

5.05

3.56

60

1800

364T

4:1

1775

71

21

93.6

178

118

2660

14.4

0.3

0.46 11.6

0.066 0.051

2

1200

184T

10:1

1160

3

1.9

86.5

9.1

4.5

2320

0.14

3.59

7.37 145

4.26

3.43

60

1200

404T

4:1

1185

74

26

94.1

266

177

1775

14

0.35

0.58 10.8

0.049 0.033

2

900

213T

10:1

865

3.3

2.2

82.5

6

1765

0.13

7.53

6.74 147

7.46

5.13

4.5

2.3

5265

0.23

4.34

2.21 193

2.84

2.02

9.1

2.62

12

185

4.52

405T

4:1

880

67

28

91.7

356

237

1330

11.6

0.49

0.82 10.2

0.079 0.071

3

3600

182T

10:1

3510

3.6

1.7

86.5

3600

365TS

4:1

3565

85

22

94.1

111

111

4455

18.2

0.2

0.46 12.8

0.045 0.041

3

1800

182T

10:1

1740

3.9

1.8

87.5

4.5

3480

0.21

2.98

4.54 146

3.13

75

1800

365T

4:1

1775

87

27

94.1

222

148

2660

18

0.23

0.37

9.2

0.051 0.041

3

1200

213T

10:1

1165

4

2.3

87.5

14

6.8

2330

0.23

3.24

4.57 130

3.25

1.73

75

1200

405T

4:1

1185

93

34

94.5

332

222

1775

18

0.26

0.45

8.4

0.035 0.025

3

900

215T

10:1

865

4.7

3.1

84

18

9

1765

0.19

5.66

5.287 118

5.23

3.87

75

900

444T

4:1

885

94

37

93

445

297

1335

17.8

0.27

0.47

7.8

0.050 0.044

5

3600

184T

10:1

3490

5.8

1.8

87.5

3.8

5235

0.36

2.62

1.54 135

1.86

1.4

100

3600

405TS

4:1

3570

108

19

94.1

147

147

3570

24.4

0.21

0.32 16

0.034 0.015

5

1800

184T

10:1

1730

6.5

3.2

87.5

15

7.6

3460

0.31

1.71

2.7

84.2

1.85

1.64

100

1800

405T

4:1

1780

113

30

94.5

295

197

2670

24.2

0.2

0.37

0.028 0.016

5

1200

215T

10:1

1160

6.8

3.3

88.5

23

11.3

2320

0.35

2.01

2.91

86.8

1.99

1.23

100

1200

444T

4:1

1185

117

38

94.5

443

296

1775

24.1

0.17

0.35

7.3

0.026 0.016

5

900

256T

10:1

865

7.5

4.1

86.5

30

15

1765

0.31

3

3.69

56.1

0.91

1.47

100

900

445T

4:1

885

123

48

94.1

593

395

1335

23.7

0.2

0.36

6.1

0.034 0.033

7.5

3600

213T

10:1

3515

8.8

3.4

88.5

11

7.5

5270

0.58

2.08

1.46

83.6

1.2

0.71

125

3600

444TS

4:1

3575

138

32

94.5

184

184

3575

30.7

0.14

0.27

8.8

0.018 0.010

7.5

1800

213T

10:1

1750

9.5

4.2

89.5

23

11.3

3500

0.57

1.27

2.48

63.2

1.03

0.75

125

1800

444T

4:1

1785

143

42

95

368

245

2675

30.5

0.14

0.33

6.7

0.017 0.011

7.5

1200

256T

10:1

1170

5

90.2

34

16.8

2340

0.58

1.41

1.71

52.1

0.68

0.53

125

1200

445T

4:1

1185

144

44

94.5

554

370

1775

30.1

0.14

0.29

6.2

0.02

0.013

7.5

900

284T

10:1

865

12

6.6

87.5

46

23

1765

0.48

2.02

2.44

34.6

0.65

0.49

125

900

447T

4:1

885

152

54

93.6

742

495

1335

29.7

0.15

0.29

4.8

0.027 0.026

10

3600

215T

10:1

3505

12

4

89.5

15

10

5255

0.76

1.67

1.27

74

0.97

0.6

150

3600

445TS

4:1

3575

164

37

95

220

220

3575

36.7

0.1

0.21

7.2

0.012 0.007

10

1800

215T

10:1

1750

13

5.4

89.5

30

15

3500

0.74

0.99

1.98

49.6

0.82

0.61

9.6

9.8

7.5

150

1800

445T

4:1

1785

170

45

95.8

441

294

2675

36.5

0.12

0.3

6.1

0.015 0.009

10

1200

284T

10:1

1165

13

89.5

45

22.5

2330

0.73

1

1.11

26.3

0.4

0.24

150

1200

447T

4:1

1185

170

45

95

665

444

1775

36.1

0.13

0.28

6.1

0.017 0.012

10

900

286T

10:1

875

15

9.1

91

60

36

1475

0.74

1.34

1.68

23.8

0.38

0.33

10

150

900

445T

4:1

885

186

72

94.1

890

593

1335

35.6

0.12

0.23

3.5

0.022 0.021

15

3600

256T

10:1

3530

17

7.4

90.2

22

15

5295

1.2

0.95

0.8

40.3

0.3

0.27

200

3600

447TS

4:1

3575

216

40

95

294

294

3575

49

0.087

0.2

7.0

0.010 0.006

15

1800

256T

10:1

1760

19

9.1

91.7

45

22.4

3520

1.2

0.6

1.26

30.7

0.26

0.26

200

1800

447T

4:1

1785

225

60

95.8

588

471

2375

48.7

0.085

0.22

4.6

0.010 0.007

15

1200

286T

10:1

1175

20

12

91

67

40

1955

1.2

0.77

0.93

22.9

0.29

0.21

200

1200

449T

4:1

1185

226

55

95

886

592

1775

48.1

0.092

0.21

4.8

0.013 0.009

15

900

324T

10:1

875

23

18

91

90

54

1475

1.1

1.15

1.68

14.8

0.23

0.193

200

900

449T

4:1

885

241

101

94.5

1186

791

1335

47.4

0.10

0.19

3.1

0.018 0.018

20

3600

284TS

10:1

3525

23

8

90.2

30

19.9

5285

1.6

0.55

1.14

38.5

0.27

0.21

250

3600

449TS

4:1

3570

267

45

95.4

368

368

3570

61

0.69

0.17

6.4

0.008 0.005

20

1800

284T

10:1

1755

26

13

91.7

60

29.9

3510

1.5

0.55

0.88

22.8

0.19

0.18

250

1800

449T

4:1

1785

281

78

95.8

735

589

2380

60.9

0.064

0.18

3.7

0.007 0.005

20

1200

324T

10:1

1175

26

15

91.7

89

54

1955

1.6

0.67

0.65

16.1

0.17

0.15

250

1200

449T

4:1

1185

280

75

95

1108

739

1775

60.2

0.076

0.18

3.8

0.010 0.008

20

900

326T

10:1

880

31

22

91

119

71

1480

1.6

0.95

1.41

12.6

0.174 0.16

250

900

S449

4:1

885

303

111

94.5

1483

989

1335

59.3

0.11

0.11

2.7

0.009 0.012

25

3600

286TS

10:1

3525

29

91.7

37

24.9

4700

2

0.42

0.98

33.8

0.2

300

3600

449TS

4:1

3575

323

68

95.8

441

441

3575

73.5

0.051

0.13

4.1

0.006 0.004

25

1800

286T

10:1

1765

29

15

93

74

49.7

2940

2

0.44

0.75

20.3

0.15

0.15

300

1800

449T

4:1

1785

346

110

95.4

882

706

2380

73.1

0.052

0.141 2.7

0.007 0.004

25

1200

326T

10:1

1180

33

19

92.4

111

67

1965

2.1

0.556 0.56

13.9

0.15

0.13

300

1200

S449

4:1

1185

335

90

95

1329

886

1775

72.1

0.092

0.091 3.2

0.007 0.008

25

900

364T

10:1

880

38

26

90.2

149

89

1480

2

0.77

1.15

350

3600

S449

4:1

3570

369

67

95.4

515

515

3570

85.3

0.064

0.062 4.2

0.005 0.004

30

3600

324TS

10:1

3525

34

12

91.7

45

29.8

4700

2.4

0.33

0.6

22.6

350

1800

S449

4:1

1785

390

115

95.8

1029

825

2380

85.3

0.066

0.079 2.4

0.004 0.004

30

1800

324T

10:1

1765

35

15

93

89

59.6

2940

2.5

0.38

0.67

18.5

0.110 0.100

350

1200

S449

4:1

1185

396

133

95

1551

1034

1775

84.2

0.069

0.067 2.3

0.005 0.006

30

1200

364T

10:1

1180

39

24

92.4

134

80

1965

2.6

0.41

0.7

11.6

0.1

400

3600

S449

4:1

3570

418

80

95.4

588

588

3570

97.4

0.052

0.052 3.5

0.004 0.004

30

900

365T

10:1

885

47

28

91

178

119

1335

2.5

0.56

0.87

7.2

400

1800

S449

4:1

1785

449

138

95.8

1176

942

2380

97.4

0.06

0.071 2.0

0.003 0.004

9.5

0.17

9.65 0.144 0.083 0.088 0.100 0.07

0.094 0.06

Efficiency values are shown for 60 hertz sine wave power.

Efficiency values are shown for 60 hertz sine wave power.

7-22

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

7-23

Dimensions

900

75

Typical Performance

60

Modifications Accessories

Modifications Accessories

INVERTER DUTY

Lead Time

Typical Performance

RGZESDI - Variable Torque / Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

Speed Range

F.L. RPM

INVERTER DUTY

460 Volts, 40ºC Ambient FL Amps

NL Amps

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

FL Torque (lb-ft)

Max Torque Max Const. HP RPM (lb-ft) Const. HP

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

HP

Synch RPM Frame

40

3600

326TS

10:1

3530

45

15

93.6

60

47.7

4705

3.3

0.25

0.49

18.8

0.072 0.083

40

1800

326T

10:1

1770

47

18

93.6

119

79.2

2940

3.4

0.31

0.54

15.8

0.082 0.082

1

1200

182T

TEFC

1000:1

1175

1.8

1.5

80

4.5

2.3

2400

5.2

9.40 185

6.28

4.54

40

1200

365T

10:1

1180

52

30

93.6

178

119

1770

3.4

0.32

0.58

10.4

0.081 0.058

1.5

3600

182T

TEFC

1000:1

3485

2

1.6

82.5

2.3

1.5

5225

4.34

2.21 193

2.84

2.02

40

900

404T

10:1

885

63

28

91.7

237

158

1335

3.4

0.49

0.82

10.2

0.079 0.071

1.5

1800

182T

TEFC

1000:1

1740

2.2

1.8

84

4.5

2.2

3480

4.93

8.37 305

5.48

4.45

50

3600

364TS

10:1

3530

55

19

93.6

74

59.6

4705

4.1

0.3

0.56

14.8

0.066 0.054

1.5

1200

184T

TEFC

1000:1

1160

2.4

1.9

85.5

6.8

3.4

2320

3.59

7.37 145

4.26

3.43

50

1800

364T

10:1

1770

58

21

93.6

148

98.9

2950

4.2

0.30

0.46

11.6

0.066 0.051

2

3600

184T

TEFC

1000:1

3505

2.5

1.7

84

3

2

5275

2.62

1.54 135

1.86

1.4

50

1200

404T

10:1

1180

66

26

93.6

223

148

1770

4.2

0.35

0.58

10.8

0.049 0.033

2

1800

182T

TEFC

1000:1

1740

2.7

1.8

84

6.1

3

3480

3.7

6.07 209

4.32

3.57

HP 1

Synch RPM Frame 1800

145T

Encl.

Speed Range

F.L. RPM

FL Amps

NL Nom. FL Amps Eff. (%)

TEFC

1000:1

1740

1.4

1.1

82.5

3

1.5

3480

7.12

8.21 335

11.28

7.59

50

900

405T

10:1

885

67

30

91.7

297

198

1330

4.2

0.49

0.82

10.2

0.08

0.071

2

1200

213T

TEFC

1000:1

1160

3.2

2.3

86.5

9.1

4.5

2320

3.24

4.57 130

3.25

1.73

60

3600

365TS

10:1

3565

68

22

93.6

89

89

4455

5.5

0.20

0.46

12.8

0.045 0.041

3

3600

213T

TEFC

1000:1

3510

3.7

3.3

86.5

4.5

3

5265

2.08

1.46

1.2

0.71

60

1800

365T

10:1

1775

71

27

93.6

178

118

2660

5.3

0.23

0.37

9.2

0.051 0.041

3

1800

184T

TEFC

1000:1

1740

4.2

3.2

87.5

9.1

4.5

3480

2.17

3.78 123

2.58

2.29

60

1200

405T

10:1

1185

74

34

94.1

266

177

1775

5.3

0.26

0.45

8.4

0.035 0.025

3

1200

215T

TEFC

1000:1

1160

4.3

3.1

87.5

6.8

2320

2.01

2.91

86.8

1.99

1.23

5

5265

1.67

1.27

74

0.97

0.6

7.5

3520

1.6

3.2

84

1.3

0.92

14

83.6

900

444T

10:1

885

78

37

91.7

356

237

1330

5.1

0.27

0.47

7.8

0.05

0.044

5

3600

215T

TEFC

1000:1

3510

5.8

3.5

87.5

75

3600

405TS

10:1

3565

85

19

94.1

111

111

4455

6.9

0.21

0.32

16

0.034 0.015

5

1800

213T

TEFC

1000:1

1760

6.5

4.2

87.5

75

1800

405T

10:1

1775

87

30

94.1

222

148

2660

6.6

0.2

0.37

9.6

0.028 0.016

5

1200

254T

TEFC

1000:1

1165

7.1

4.5

88.5

23

11.3

2330

1.66

1.89

54.3

0.82

0.58

75

1200

444T

10:1

1185

93

38

94.5

332

222

1775

6.6

0.17

0.35

7.3

0.026 0.016

5

900

254T

TEBC

1000:1

865

7.5

4.1

86.5

30

15

1730

4.09

4.8

68.4

1.46

1.99

75

900

445T

10:1

885

94

48

93

445

297

1335

6.4

0.2

0.36

6.1

0.03

0.033

7.5

3600

254T

TEFC

1000:1

3510

8.7

5

88.5

11

7.5

5265

1.33

1.03

57.6

0.39

0.31

100

3600

444TS

10:1

3570

108

32

94.1

147

147

3570

9.2

0.14

0.27

8.8

0.018 0.010

7.5

1800

254T

TEFC

1000:1

1775

9.5

7.3

89.5

23

11.1

3550

1.3

2.7

66

0.7

0.52

100

1800

444T

10:1

1780

113

42

94.5

295

197

2670

9

0.14

0.33

6.7

0.017 0.011

7.5

1200

256T

TEFC

1000:1

1165

10

5

90.2

34

16.8

2330

1.41

1.71

52.1

0.68

0.53

100

1200

445T

10:1

1185

117

44

94.5

443

296

1775

8.9

0.14

0.29

6.2

0.02

7.5

900

256T

TEBC

1000:1

865

12

6.6

87.5

46

23

1730

3

3.69

56.1

0.91

1.47

TEFC

1000:1

3515

12.5

6

89.5

15

10

5270

0.95

0.8

40.3

0.3

0.27

5.7

89.5

30

15

3500

0.86

1.90

48

0.45

0.38

90.2

45

22

2330

1.41

1.71

52

0.68

0.53

91

60

36

1475

2.02

2.44

35

0.65

0.49

0.013

900

447T

10:1

885

123

54

94.1

593

395

1335

8.5

0.15

0.29

4.8

0.027 0.03

10

3600

256T

125

3600

445TS

10:1

3575

138

37

94.5

184

184

3575

11.7

0.1

0.21

7.2

0.012 0.007

10

1800

256T

TEFC

1000:1

1770

12.5

125

1800

445T

10:1

1785

143

45

95

368

245

2675

11.6

0.12

0.3

6.1

0.015 0.009

10

1200

256T

TEBC

1000:1

1165

13

125

1200

447T

10:1

1185

144

45

94.5

554

370

1775

11.1

0.13

0.28

6.1

0.017 0.012

10

900

284T

TEBC

1000:1

875

15

9.1

0.15

0.29

4.8

125

900

447T

10:1

885

152

72

93.6

742

495

1335

10.6

150

3600

447TS

10:1

3575

164

40

95

220

220

3575

14

0.087 0.2

7

10

0.027 0.026

15

3600

254T

TEBC

1000:1

3530

18

5

90.2

22

15

5295

1.33

1.03

57.6

0.39

0.31

0.01

0.006

15

1800

254T

TEBC

1000:1

1760

20

7.3

91.7

45

22

3520

0.85

1.61

38.5

0.38

0.34

1200

284T

TEBC

1000:1

1175

20

10

91

67

40

1955

1.00

1.11

26.3

0.40

0.24

14

150

1800

447T

10:1

1785

170

60

95.8

441

294

2675

13.9

0.085 0.22

4.6

0.01

0.007

15

150

1200

449T

10:1

1185

170

55

95

665

444

1775

13.3

0.092 0.21

4.8

0.013 0.009

15

900

286T

TEBC

1000:1

875

23

150

900

449T

10:1

885

186

101

94.1

890

593

1335

12.7

0.10

0.19

3.1

0.018 0.018

20

3600

256T

TEBC

1000:1

3525

23

200

3600

449TS

10:1

3575

223

45

95

294

294

3575

18.8

0.69

0.17

6.4

0.008 0.005

20

1800

256T

TEBC

1000:1

1755

27

200

1800

449T

10:1

1785

239

78

95.8

588

471

2375

18.5

0.064 0.18

3.7

0.007 0.005

20

1200

286T

TEBC

1000:1

1175

26

12

200

1200

449T

10:1

1185

238

75

95

886

592

1775

17.7

0.076 0.18

3.8

0.01

0.008

20

900

324T

TEBC

1000:1

880

31

18

91

250

3600

449TS

10:1

3575

282

68

95.4

368

368

3570

23.5

0.05

4.1

0.006 0.004

25

3600

284TS

TEBC

1000:1

3525

29

8

250

1800

449TS

10:1

1785

302

110

95.8

735

589

2380

23.1

0.052 0.141 2.7

0.007 0.004

25

1800

284T

TEBC

1000:1

1765

29

13

250

1200 S449SS

10:1

1185

296

90

95

1108

739

1775

22.2

0.092 0.091 3.2

0.007 0.008

25

1200

324T

TEBC

1000:1

1180

33

15

92.4

111

67

1965

0.67

0.65

300

3600 S449SS

10:1

3575

333

67

95.8

441

441

3575

28.1

0.064 0.062 4.2

0.005 0.004

25

900

326T

TEBC

1000:1

880

38

22

90.2

149

89

1480

0.95

1.41

300

1800 S449SS

10:1

1785

356

115

95.4

882

882

2380

27.7

0.066 0.079 2.4

0.004 0.004

30

3600

286TS

TEBC

1000:1

3525

34

91.7

45.0

30

4700

0.42

0.98

33.8

0.2

350

3600 S449SS

10:1

3575

392

80

95.4

515

515

3570

32.9

0.05

0.052 3.5

0.004 0.004

30

1800

286T

TEBC

1000:1

1765

35

15

93

89

60

2940

0.44

0.75

20.3

0.15

0.15

350

1800 S449SS

10:1

1785

406

138

95.8

1029

1029

2380

32.3

0.06

0.071

0.003 0.004

30

1200

326T

TEBC

1000:1

1180

39

19

92.4

134

80

1965

0.56

0.56

13.9

0.15

0.13

30

900

364T

TEBC

1000:1

885

47

26

91

178

119

1335

0.77

1.15

9.7

0.144 0.083

40

3600

324TS

TEBC

1000:1

3530

46

12

93.6

60

48

4705

0.33

0.60

22.6

0.088 0.100

40

1800

324T

TEBC

1000:1

1770

47

15

93.6

119

79

2940

0.38

0.67

18.5

0.110 0.100

40

1200

364T

TEBC

1000:1

1180

52

24

93.6

178

119

1770

0.41

0.70

11.6

0.100 0.070

40

900

365T

TEBC

1000:1

885

63

36

91.7

237

158

1335

0.56

0.87

7.2

0.094 0.061

Efficiency values are shown for 60 hertz sine wave power.

0.13

2

91

90

54

1475

1.34

1.68

23.8

0.38

0.33

7.4

90.2

30

20

5285

0.95

0.80

40.3

0.30

0.27

9.1

91.7

60

30

3510

0.60

1.26

30.7

0.26

0.26

91.7

89

54

1955

0.77

0.93

22.9

0.29

0.21

119

71

1480

1.15

1.68

14.8

0.23

0.193

91.7

37

25

4700

0.55

1.14

38.5

0.27

0.21

93

74

50

2940

0.55

0.88

22.8

0.19

0.18

16.1

0.17

0.15

12.6

0.174 0.159

9.5

0.17

Efficiency values are shown for 60 hertz sine wave power.

7-24

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

7-25

Dimensions

100

7.5 15

Typical Performance

60

Modifications Accessories

Modifications Accessories

460 Volts, 40ºC Ambient

RGZESDI - 1000:1 Constant Torque

Lead Time

Typical Performance

INVERTER DUTY

INVERTER Duty Hazardous Duty

Dimensions

RGZESDI - 10:1 Constant Torque

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

HP 50

3600

326TS

50

1800

50 50

INVERTER DUTY

460 Volts, 40ºC Ambient

460 Volts, 40ºC Ambient Synch RPM Frame

RGZZESDI - 6:1 Variable or 6:1 Constant Torque

FL Amps

NL Nom. FL Amps Eff. (%)

FL Torque (lb-ft)

Max Torque Max Const. HP RPM (lb-ft) Const. HP

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

Synch RPM Frame

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

F.L. RPM

FL Amps

NL Amps

143T

6:1

3530

1.5

0.9

82.5

1.5

1.5

3600

0.15

6.87

3.18 372

6.40

4.52

145T

6:1

1760

1.7

1.4

83.6

3

1.5

3600

0.15

4.94

5.27 199

6.98

4.37

1482

6:1

1175

1.7

1.5

85.5

4.5

2.3

2400

0.15

5.22

9.40 185

6.28

4.54

184T

6:1

870

1.9

1.2

78.5

6.1

3

1800

0.14

8.31 12.02 202

3600

145T

6:1

3525

1.9

1.1

84

2.2

2.2

3600

0.22

4.87

2.445 286

4.59

3.56

1800

145T

6:1

1750

2.5

1.9

84

4.5

2.3

3600

0.21

3.80

4.16 165

5.05

3.56

184T

6:1

1170

2.6

1.9

86.2

6.7

3.4

2400

0.22

3.59

7.37 145

4.26

3.43

213T

6:1

870

2.8

1.8

80

9.2

4.5

1800

0.21

7.53

6.74 147

7.46

5.13

182T

6:1

3545

2.6

1.7

86.5

3

3

3600

0.31

4.34

2.21 193

2.84

2.02

1800

145T

6:1

1765

3

1.8

87.5

5.9

3

3600

0.30

2.98

4.54 146

3.13

2.62

1200

213T

6:1

1190

2.8

2.3

88.5

8.8

4.4

2400

0.30

3.24

4.57 130

3.25

1.73

2

900

215T

6:1

870

3.5

2.2

82.5

5.9

1800

0.27

5.66

5.27 118

5.23

3.87

16.0 0.034 0.015

3

3600

184T

6:1

3545

3.6

1.8

87.5

4.4

4.4

3600

0.46

2.62

1.54 135

1.86

1.40

9.6 0.028 0.016

3

1800

184T

6:1

1755

4.6

3.2

87.5

9

4.5

3600

0.44

1.71

2.70

84.2 1.85

1.64

0.35

7.3 0.026 0.016

3

1200

215T

6:1

1190

4.4

3.3

89.5

13.2

6.6

2400

0.48

2.01

2.91

86.8 1.99

1.23

0.2

0.36

6.1 0.034 0.033

3

900

254T

6:1

880

5.5

3.1

84

8.8

1350

0.45

4.09

4.8

68.4 1.46

1.99

0.14

0.27

8.8 0.018 0.010

5

3600

213T

6:1

3565

6.2

3.4

88.5

7.4

7.4

3600

0.80

2.08

1.46

83.6 1.2

0.71

2675

0.14

0.33

6.7 0.017 0.011

5

1800

213T

6:1

1760

7.3

4.2

89.5

14.9

7.5

3600

0.74

1.27

2.48

63.2 1.03

0.750

370

1775

0.14

0.29

6.2 0.02

5

1200

254T

6:1

1180

7

4.5

90.2

22.2

14.8

1800

0.76

1.66

1.89

54.3 0.820 0.580

742

495

1335

0.15

0.29

4.8 0.027 0.026

5

900

256T

6:1

870

9

4.1

86.5

30

15

1350

0.69

3.00

3.69

56.1 0.91

220

220

3575

0.1

0.21

7.2 0.012 0.007

7.5

3600

215T

6:1

3525

9.2

4

89.5

11.2

11.2

3600

1.1

1.67

1.27

74

1800

215T

6:1

1760

10.7

5.4

89.5

22.4

11.2

3600

1.1

0.99

1.98

49.6 0.82

Encl.

F.L. RPM

TEBC

1000:1

3530

55

15

93.6

74

60

4705

0.25

0.49

18.8 0.072 0.083

1

3600

326T

TEBC

1000:1

1770

58

18

93.6

148

99

2950

0.31

0.54

15.8 0.082 0.082

1

1800

1200

365T

TEBC

1000:1

1180

66

30

93.6

223

148

1770

0.32

0.58

10.4 0.081 0.058

1

1200

900

404T

TEBC

1000:1

880

67

28

91.7

297

198

1330

0.49

0.82

10.2 0.079 0.071

1

900

60

3600

364TS

TEBC

1000:1

3565

68

19

93.6

89

89

4455

0.30

0.56

14.8 0.066 0.054

1.5

60

1800

364T

TEBC

1000:1

1775

71

21

93.6

178

118

2660

0.30

0.46

11.6 0.066 0.051

1.5

60

1200

404TS

TEBC

1000:1

1185

72

26

94.1

266

177

1775

0.35

0.58

10.8 0.049 0.033

1.5

1200

60

900

405TS

TEBC

1000:1

880

78

28

91.7

356

237

1330

0.41

0.70

8.8 0.063 0.06

1.5

900

75

3600

365TS

TEBC

1000:1

3565

85

22

94.1

111

111

4455

0.20

0.46

12.8 0.045 0.041

2

3600

75

1800

365T

TEBC

1000:1

1775

87

27

94.1

222

148

2660

0.23

0.37

9.2 0.051 0.041

2

75

1200

405TS

TEBC

1000:1

1185

87

34

94.5

332

222

1775

0.26

0.45

8.4 0.035 0.025

2

75

900

444TS

TEBC

1000:1

885

94

37

93

445

297

1335

0.27

0.47

7.5 0.05

0.044

100

3600

405TS

TEBC

1000:1

3570

110

19

94.1

147

147

3570

0.21

0.32

100

1800

405TS

TEBC

1000:1

1780

113

30

94.5

295

197

2670

0.2

0.37

100

1200

444TS

TEBC

1000:1

1185

115

38

94.5

443

296

1775

0.17

100

900

445TS

TEBC

1000:1

885

123

48

94.1

593

395

1335

125

3600

444TS

TEBC

1000:1

3575

136

32

94.5

184

184

3575

125

1800

444TS

TEBC

1000:1

1785

143

42

95

368

245

125

1200

445TS

TEBC

1000:1

1185

144

44

94.5

554

125

900

447TS

TEBC

1000:1

885

152

54

93.6

150

3600

445TS

TEBC

1000:1

3575

160

37

95

0.013

HP

12

18

8.31 12.08

0.97

1.47 0.60

1800

445TS

TEBC

1000:1

1785

169

45

95.8

441

294

2675

0.12

0.3

6.1 0.015 0.009

150

1200

447TS

TEBC

1000:1

1185

169

45

95

665

444

1775

0.13

0.28

6.1 0.017 0.012

7.5

1200

256T

6:1

1175

10

5

90.2

33.5

22.3

1800

1.1

1.41

1.71

52.1 0.680 0.530

150

900

447TS

TEBC

1000:1

885

186

72

94.1

890

593

1335

0.12

0.23

3.5 0.022 0.021

7.5

900

284T

6:1

880

12

6.6

87.5

46

30

1350

1.1

2.02

2.44

34.6 0.65

0.49

200

3600

447TS

TEBC

1000:1

3575

208

40

95

294

294

3575

0.087 0.2

7.0 0.01

0.006

10

3600

254T

6:1

3550

11.8

5

90.2

14.8

14.8

3600

1.6

1.33

1.03

57.6 0.39

0.31

200

1800

447TS

TEBC

1000:1

1785

223

60

95.8

588

471

2375

0.085 0.22

4.6 0.01

0.007

10

1800

254T

6:1

1770

13.7

7.3

91.7

29.7

19.8

2700

1.5

0.85

1.61

38.5 0.380 0.370

200

1200

449TS

TEBC

1000:1

1185

222

55

886

592

1775

0.092 0.21

4.8 0.013 0.009

10

1200

284T

6:1

1180

200

900

449TS

TEBC

1000:1

885

241

101

94.5

1186

791

1335

0.100 0.19

3.1 0.018 0.018

10

900

286T

6:1

885

250

3600

449TS

TEBC

1000:1

3570

264

45

95.4

368

368

3570

0.690 0.17

6.4 0.008 0.005

15

3600

256T

6:1

250

1800

449TS

TEBC

1000:1

1785

282

78

95.8

735

589

2380

0.064 0.18

3.7 0.007 0.005

15

1800

256T

6:1

250

1200

449TS

TEBC

1000:1

1185

285

75

95

1108

739

1775

0.076 0.18

3.8 0.01

0.008

15

1200

286T

6:1

1180

20

12

91.7

900 S449SS

TEBC

1000:1

885

303

111

94.5

1483

989

1335

0.110 0.11

2.7 0.009 0.012

15

900

324T

6:1

885

25

14

91

8

250

14.5

10

0.610

91

44.5

29.7

1800

1.5

1.00

1.11

26.3 0.400 0.240

17

9.1

91

60

39

1350

1.5

1.34

1.68

23.8 0.38

0.33

3540

17.6

7.4

90.2

22.2

22.2

3600

2.3

0.95

0.80

40.3 0.30

0.27

1765

20

9.1

91.7

44.6

29.7

2700

2.3

0.60

1.26

30.7 0.260 0.260

66.7

44.5

1800

2.3

0.77

0.93

22.9 0.290 0.210

90

59

1350

2.3

1.15

1.68

14.8 0.23

0.193

91.7

29.7

29.7

3600

3.1

0.55

1.14

38.5 0.27

0.21

13

93

59.3

39.5

2700

3.1

0.55

0.88

22.8 0.190 0.180

300

3600

449TS

TEBC

1000:1

3575

330

68

95.8

441

441

3575

0.051 0.13

4.1 0.006 0.004

20

3600

284TS

6:1

3540

23.4

300

1800

449TS

TEBC

1000:1

1785

345

110

95.4

882

706

2380

0.052 0.141

2.7 0.007 0.004

20

1800

284T

6:1

1770

24

300

1200 S449SS

TEBC

1000:1

1185

335

90

95

1329

886

1775

0.092 0.091

3.2 0.007 0.008

20

1200

324T

6:1

1180

28

15

92.4

89

350

3600 S449SS

TEBC

1000:1

3570

370

67

95.4

515

515

3570

0.064 0.062

4.2 0.005 0.004

20

900

326T

6:1

885

33

18

91

119

59.3

1800

3.1

0.67

0.65

16.1 0.170 0.150

79

1350

3.1

0.95

1.41

12.6 0.174 0.159

350

1800 S449SS

TEBC

1000:1

1785

390

115

95.8

1029

825

2380

0.066 0.079

2.4 0.004 0.004

25

3600

286TS

6:1

3535

28.5

10

91.7

37.1

37.1

3600

3.8

0.42

0.98

33.8 0.20

350

1200 S449SS

TEBC

1000:1

1185

396

133

95

1551

1034

1775

0.069 0.067

2.3 0.005 0.006

25

1800

286T

6:1

1770

30

15

93

74.2

49.5

2700

3.8

0.44

0.75

20.3 0.150 0.150

400

3600 S449SS

TEBC

1000:1

3570

420

80

95.4

588

588

3570

0.052 0.052

3.5 0.004 0.004

25

1200

326T

6:1

1180

33

19

92.4

111

74.1

1800

3.8

0.56

0.56

13.9 0.150 0.130

400

1800 S449SS

TEBC

1000:1

1785

450

138

95.8

1176

942

2380

0.060 0.071

2.0 0.003 0.004

25

900

364T

6:1

885

41

22

91

149

99

1350

3.8

0.77

1.15

30

3600

324TS

6:1

3540

35.3

12

93.6

44.5

3600

4.6

0.33

0.60

Efficiency values are shown for 60 hertz sine wave power.

44.5 88.7

0.17

9.7 0.144 0.083 22.6 0.09

0.10

30

1800

324T

6:1

1775

34

15

93.6

59.1

2700

4.7

0.38

0.67

18.5 0.110 0.100

30

1200

364T

6:1

1180

41

24

93.6

134

89

1800

4.6

0.41

0.7

11.6 0.100 0.070

30

900

365T

6:1

890

52

26

91

178

118

1350

4.8

0.56

0.87

7.22 0.094 0.061

Efficiency values are shown for 60 hertz sine wave power.

7-26

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

7-27

Dimensions

150

7.5

95

Typical Performance

Speed Range

Speed Range

Modifications Accessories

Modifications Accessories

INVERTER DUTY

Lead Time

Typical Performance

RGZESDI - 1000:1 Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

Hazardous Duty Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time

DP10

460 Volts, 40ºC Ambient Speed Range

F.L. RPM

FL Amps

NL Amps

Max FL Torque Max HP @ Min Nom. FL Torque Const. HP RPM Const. Eff. (%) (lb-ft) (lb-ft) Const. HP Torque

Ohms/Phase (Y equiv.) Circuit Parameters 25ºC X1 X2 XM R1 R2

HP

Synch RPM Frame

40

3600

326TS

6:1

3540

44.5

15

93.6

59

40

1800

326T

6:1

1775

48

18

93.6

118

40

1200

365T

6:1

1185

55

30

93.6

177

40

900

404T

6:1

885

53

36

91.7

50

3600

364TS

6:1

3570

57

19

50

1800

364T

6:1

1775

60

21

50

1200

404T

6:1

1185

61

26

94.1

222

148

1800

50

900

405T

6:1

885

66

28

91.7

297

197

1350

60

3600

365TS

6:1

3570

69

22

94.1

88

88

3600

60

1800

365T

6:1

1775

71

27

94.1

177

118

2700

60

1200

405T

6:1

1190

74

34

94.5

265

176

60

900

444T

6:1

890

77

30

91.7

356

75

3600

405TS

6:1

3570

81

19

94.1

75

1800

405T

6:1

1780

86

30

94.5

75

1200

444T

6:1

1185

88

38

75

900

445T

6:1

890

95

100

3600

444TS

6:1

3580

100

1800

444T

6:1

1785

100

1200

445T

6:1

1185

118

44

94.5

443

295

1800

15.6

0.14

0.29

6.2

0.02

100

900

447T

6:1

890

124

48

94.1

593

392

1350

15.8

0.15

0.29

4.8

0.027 0.026

125

3600

445TS

6:1

3580

137

37

95

183

183

3600

20.2

0.10

0.21

7.2

0.012 0.007

125

1800

445T

6:1

1785

143

45

95.8

386

245

2700

20

0.12

0.30

6.1

0.015 0.009

125

1200

447T

6:1

1185

142

45

95

554

369

1800

19.5

0.13

0.28

6.1

0.017 0.012

125

900

449T

6:1

890

159

54

93.6

742

490

1350

19.8

0.12

0.23

3.51 0.022 0.021

150

3600

447TS

6:1

3580

159

40

95

220

220

3600

24.3

0.087 0.20

59

3600

6.1

0.25

0.49

18.8

0.072 0.083

78.9

2700

6.2

0.31

0.54

15.8

0.082 0.082

118

1800

6.2

0.32

0.58

10.4

0.081 0.058

237

157

1350

6.1

0.49

0.82

10.23 0.079 0.071

93.6

74

74

3600

8

0.30

0.56

14.8

0.066 0.054

93.6

148

98.6

2700

7.6

0.30

0.46

16.0

0.066 0.051

7.8

0.035 0.58

10.8

0.049 0.033

7.6

0.41

0.70

9.6

0.20

0.46

12.8

0.045 0.041

9.3

0.23

0.37

9.2

0.052 0.041

1800

9.6

0.26

0.45

8.4

0.035 0.025

235

1350

9.5

0.27

0.47

7.81 0.050 0.044

110

110

3600

11.9

0.21

0.32

16.0

0.034 0.015

221

147

2700

11.8

0.20

0.37

9.6

0.028 0.016

94.5

333

222

1800

11.7

0.17

0.35

7.3

0.026 0.016

37

93

445

294

1350

11.9

0.2

0.36

6.07 0.034 0.033

111

32

94.5

147

147

3600

16.2

0.14

0.27

8.8

0.018 0.010

118

42

95

294

196

2700

16

0.14

0.33

6.7

0.017 0.011

8.78 0.063 0.060

150

1800

447T

6:1

1785

171

60

95.8

441

294

2700

23.9

0.085 0.22

4.6

0.010 0.007

150

1200

449T

6:1

1185

170

55

95

665

443

1800

23.4

0.092 0.21

4.8

0.013 0.009

150

900

449T

6:1

890

186

72

94.1

890

588

1350

23.7

0.10

200

3600

449TS

6:1

3575

213

45

95.4

294

294

3600

32.2

0.069 0.17

6.4

200

1800

449T

6:1

1785

223

78

95.8

588

392

2700

31.9

0.064 0.18

3.7

0.007 0.005

200

1200

449T

6:1

1185

225

75

95

886

591

1800

31.2

0.076 0.18

3.8

0.010 0.008

Efficiency values are shown for 60 hertz sine wave power.

0.19

3.08 0.018 0.018 0.008 0.005

R 0.771 0.771 0.986 0.986 1.201 1.201 1.416 1.416 1.591 1.416 1.591 1.416 1.845 1.591 1.845 1.591 2.021 1.591 2.021 1.591 2.45 1.845 2.45 1.845 2.88 2.021 2.88 2.021 2.88 2.021 2.88 2.021

ES 1.375 1.375 1.75 1.75 2.375 2.375 2.875 2.875 3.25 1.875 3.25 1.875 3.875 2 3.875 2 4.25 2 4.25 2 5.625 2.75 5.625 2.75 6.88 3 6.88 3 6.88 3 6.88 3

C 10.53 11.5 12.53 13.53 15.85 17.38 20.67 22.4 23.82 22.45 25.32 23.95 26.26 24.76 27.76 26.26 29.13 27 30.13 28 33.1 30.1 34.6 31.6 39.89 36.12 39.89 36.12 43.39 39.62 48.4 44.62

D 3.50 3.50 4.50 4.50 5.25 5.25 6.25 6.25 7 7 7 7 8 8 8 8 9 9 9 9 10 10 10 10 11 11 11 11 11 11 11 11

E 2.75 2.75 3.75 3.75 4.25 4.25 5 5 5.5 5.5 5.5 5.5 6.25 6.25 6.25 6.25 7 7 7 7 8 8 8 8 9 9 9 9 9 9 9 9

2F 4.0 5.0 4.5 5.5 5.5 7.0 8.25 10 9.5 9.5 11 11 10.5 10.5 12 12 11.25 11.25 12.25 12.25 12.25 12.25 13.75 13.75 14.5 14.5 16.5 16.5 20 20 25 25

BA 2.25 2.25 2.75 2.75 3.5 3.5 4.25 4.25 4.75 4.75 4.75 4.75 5.25 5.25 5.25 5.25 5.88 5.88 5.88 5.88 6.62 6.62 6.62 6.62 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5

N-W 2.25 2.25 2.75 2.75 3.38 3.38 4 4 4.62 3.25 4.62 3.25 5.25 3.75 5.25 3.75 5.88 3.75 5.88 3.75 7.25 4.25 7.25 4.25 8.5 4.75 8.5 4.75 8.5 4.75 8.5 4.75

O 7.54 7.54 9.17 9.17 10.82 10.82 12.54 12.54 14.57 14.57 14.57 14.57 16.34 16.34 16.34 16.34 18.26 18.26 18.26 18.26 20.24 20.24 20.24 20.24 21.62 21.62 21.62 21.62 21.69 21.69 21.75 21.75

T 1.63 1.63 1.63 1.63 2.01 2.01 2.36 2.36 2.36 2.36 2.36 2.36 2.36 2.36 2.79 2.79 2.79 2.79 3.54 3.54 3.54 3.54 3.54 3.54 3.54 3.54 3.54 3.54 3.54 3.54

P 6.81 6.81 8.7 8.7 10.55 10.55 12.8 12.8 14.76 14.76 14.76 14.76 16.69 16.69 16.69 16.69 18.31 18.31 18.31 18.31 20.24 20.24 20.24 20.24 21.25 21.25 21.25 21.25 21.38 21.38 21.5 21.5

AB 6.3 6.3 7 7 8.19 8.19 10.83 10.83 13.18 13.18 13.18 13.18 14.09 14.09 14.09 14.09 14.81 14.81 14.81 14.81 20.08 20.08 20.08 20.08 19.85 19.85 19.85 19.85 22 22 22 22

U 0.875 0.875 1.125 1.125 1.375 1.375 1.625 1.625 1.875 1.625 1.875 1.625 2.125 1.875 2.125 1.875 2.375 1.875 2.375 1.875 2.875 2.125 2.875 2.125 3.375 2.375 3.375 2.375 3.375 2.375 3.375 2.375

*440 frame motors have 8 hole footprints. Dimensions in inches Dimensions are for reference only.

7-28

2007 Low Voltage AC Motors Selection and Pricing Guide

8-1

Dimensions

0.010 0.006

S 0.188 0.188 0.250 0.250 0.312 0.312 0.375 0.375 0.500 0.375 0.500 0.375 0.5 0.5 0.5 0.5 0.625 0.5 0.625 0.5 0.75 0.5 0.75 0.5 0.875 0.625 0.875 0.625 0.875 0.625 0.875 0.625

Typical Performance

7.0

0.013

Frame 143T 145T 182T 184T 213T 215T 254T 256T 284T 284TS 286T 286TS 324T 324TS 326T 326TS 364T 364TS 365T 365TS 404T 404TS 405T 405TS 444T 444TS 445T 445TS 447T 447TS 449T 449TS

Modifications Accessories

Modifications Accessories

INVERTER DUTY

Lead Time

Typical Performance

RGZZESDI - 6:1 Variable or 6:1 Constant Torque

INVERTER Duty Hazardous Duty

Dimensions

INVERTER Duty Severe Duty

General Purpose - ODP Motors

Hazardous Duty Motors

INVERTER Duty Severe Duty

DP10 C-Face with Feet

DP10 D-Flange with Feet

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

General Purpose - ODP Motors

INVERTER Duty Severe Duty

General Purpose - ODP Motors

Typical Performance

AK 4.5

U 0.875

N-W 2.25

V 1.88

BA 2.25 (1)

ES 1.41

S 0.188

BF# 4

BF DIA 3/8”-16NC

Frame 444TD

BD 22

AJ 20

AK 18

U 3.375

N-W 8.50

V 8.25

BA 7.5

ES 6.88

S 0.875

BF# 8

BF DIA 5/8”-11NC

145TC

6.5

5.875

4.5

0.875

2.25

1.88

2.25 (1)

1.41

0.188

4

3/8”-16NC

444TSD

22

20

18

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

182TC

9

7.25

8.5

1.125

2.75

2.50

2.75 (1)

1.81

0.25

4

1/2”-13NC

445TD

22

20

18

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

184TC

9

7.25

8.5

1.125

2.75

2.50

2.75 (1)

1.81

0.25

4

1/2”-13NC

445TSD

22

20

18

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

213TC

9

7.25

8.5

1.375

3.38

3.12

3.5 (1)

2.44

0.312

4

1/2”-13NC

447TD

22

20

18

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

215TC

9

7.25

8.5

1.375

3.38

3.12

3.5 (1)

2.44

0.312

4

1/2”-13NC

447TSD

22

20

18

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

254TC

10

7.25

8.5

1.625

4.00

3.75

4.25 (1)

2.91

0.375

4

1/2”-13NC

449TD

22

20

18

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

256TC

10

7.25

8.5

1.625

4.00

3.75

4.25 (1)

2.91

0.375

4

1/2”-13NC

449TSD

22

20

18

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

284TC

11

9

10.5

1.875

4.62

4.38

4.75

3.25

0.5

4

1/2”-13NC

284TSC

11

9

10.5

1.625

3.25

3.00

4.75

1.88

0.375

4

1/2”-13NC

286TC

11

9

10.5

1.875

4.62

4.38

4.75

3.25

0.5

4

1/2”-13NC

286TSC

11

9

10.5

1.625

3.25

3.00

4.75

1.88

0.375

4

1/2”-13NC

324TC

13

11

12.5

2.125

5.25

5.00

5.25

3.88

0.5

8

5/8”-11NC

324TSC

13

11

12.5

1.875

3.75

3.50

5.25

2.00

0.5

8

5/8”-11NC

326TC

13

11

12.5

2.125

5.25

5.00

5.25

3.88

0.5

8

5/8”-11NC

326TSC

13

11

12.5

1.875

3.75

3.50

5.25

2.00

0.5

8

5/8”-11NC

364TC

13

11

12.5

2.375

5.88

5.62

5.88

4.25

0.625

8

5/8”-11NC

364TSC

13

11

12.5

1.875

3.75

3.50

5.88

2.00

0.5

8

5/8”-11NC

365TC

13

11

12.5

2.375

5.88

5.62

5.88

4.25

0.625

8

5/8”-11NC

365TSC

13

11

12.5

1.875

3.75

3.50

5.88

2.00

0.5

8

5/8”-11NC

404TC

13

11

12.5

2.875

7.25

7.00

6.62

5.63

0.75

8

5/8”-11NC

404TSC

13

11

12.5

2.125

4.25

4.00

6.62

2.75

0.5

8

5/8”-11NC

405TC

13

11

12.5

2.875

7.25

7.00

6.62

5.63

0.75

8

5/8”-11NC

405TSC

13

11

12.5

2.125

4.25

4.00

6.62

2.75

0.5

8

5/8”-11NC

444TC

16.77

14

16

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

444TSC

16.77

14

16

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

445TC

16.77

14

16

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

445TSC

16.77

14

16

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

447TC

16.77

14

16

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

447TSC

16.77

14

16

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

449TC

16.77

14

16

3.375

8.50

8.25

7.5

6.88

0.875

8

5/8”-11NC

449TSC

16.77

14

16

2.375

4.75

4.50

7.5

3.00

0.625

8

5/8”-11NC

Dimensions in inches Dimensions are for reference only.

Dimensions

Dimensions

AJ 5.875

(1) Not according to NEMA standard. Dimensions in inches Dimensions are for reference only.

8-2

2007 Low Voltage AC Motors Selection and Pricing Guide

Typical Performance

BD 6.5

Modifications Accessories

Modifications Accessories

Lead Time

Lead Time

Frame 143TC

2007 Low Voltage AC Motors Selection and Pricing Guide

8-3

INVERTER Duty Severe Duty

General Purpose - TEFC Motors

GP10A/GP100A (Cast Aluminum Frame)

GP10A/GP100A (Cast Aluminum Frame)

INVERTER Duty Severe Duty

General Purpose - TEFC Motors

D-Flange with Feet INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Footed

C

C

AB

AH

ÿ BF

AB BB min. CC

CC

ÿ AJ

ES

CB

D

AF

ø BD

øAK

G_

G_

D

øU

AF

øU

O

øP

CB

øP

O

Lead Time

Lead Time

ES

øH

øH

AA

K 2F

J

FK 2F

2E

N -W

A

BA

J 2E

N -W

2 F1

2 F1

AC

AA

K

BA

Modifications Accessories

Modifications Accessories

FK

AC

A

B

B

D-Flange without Feet

C-Face with Feet C C

AB

AB

AH

BF

ÿ BF

BB min.

BB min.

Typical Performance

Typical Performance

AH_

CC

CC

ÿ AJ_

Keyseat detail

CB AF

øBD

ø AK

G_

Dimensions

Dimensions

S

D

øU

AF

øP

CB

øBD

ø AK øU

øP

O

ÿ AJ

ES

ES

øH FK

AA

K 2F

AC

J

AC

AA

2E

N -W

R

N -W 2 F1

BA

C-Face

A

B

C-Face without Feet C

AB

AH_

BF

BB min. CC

ÿ AJ_

AF

CB

øBD

øU

øP

øAK

ES

AA N -W

8-4

2007 Low Voltage AC Motors Selection and Pricing Guide

AC

Frame

C

D

2E

2F

143T

14.37

3.5

5.5

4

145T

2F1

0

P

U

AB

BA

2.25

7.28

7.56

0.875

7

2.25

AH

AJ

2.12 5.875

D-Flange

AK

BD

BF

AH

4.5

6.6 3/8-16 2.25

AJ 10

AK

BD

Keyseat BF

R

S

ES

9 10.9 0.53 0.771 0.188 1.41

14.37

3.5

5.5

2.25

7.28

7.56

0.875

7

2.25

2.12 5.875

4.5

6.6 3/8-16 2.25

10

9 10.9 0.53 0.771 0.188 1.41

182T(1) 15.69

4.5

7.5

4.5

2.75

8.87

8.74

1.125

6.94

2.75

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

182T(2) 16.68

4.5

7.5

4.5

2.75

8.87

8.74

1.125

6.94

2.75

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

184T(1) 15.69

4.5

7.5

5.5

2.75

8.87

8.74

1.125

6.94

2.75

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

184T(2) 16.68

4.5

7.5

5.5

2.75

8.87

8.74

1.125

6.94

2.75

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

213T(3) 18.68 5.25

8.5

5.5

3.38 10.41 10.31 1.375

8.27

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

10

9 10.9 0.53 1.201 0.312 2.44

213T(4) 20.65 5.25

8.5

5.5

3.38 10.41 10.31 1.375

8.27

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

10

9 10.9 0.53 1.201 0.312 2.44

215T(3) 18.68 5.25

8.5

7

3.38 10.41 10.31 1.375

8.27

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

10

9 10.9 0.53 1.201 0.312 2.44

215T(4) 20.65 5.25

8.5

7

3.38 10.41 10.31 1.375

8.27

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

10

9 10.9 0.53 1.201 0.312 2.44

254T(5) 23.8

10

8.25

9.35

4.25

3.75

7.25

8.5

9.3 1/2-13

254T(6) 26.16 6.25

10

8.25

4

12.43 12.36 1.625

9.35

4.25

3.75

7.25

8.5

9.3 1/2-13

4

12.5 11 13.9 0.81 1.416 0.375 2.91

256T(5) 23.8

6.25

10

10

4

12.43 12.36 1.625

9.35

4.25

3.75

7.25

8.5

9.3 1/2-13

4

12.5 11 13.9 0.81 1.416 0.375 2.91

256T(6) 26.16 6.25

10

10

4

12.43 12.36 1.625

9.35

4.25

3.75

7.25

8.5

9.3 1/2-13

4

12.5 11 13.9 0.81 1.416 0.375 2.91

6.25

5

N-W

4

12.43 12.36 1.625

4

12.5 11 13.9 0.81 1.416 0.375 2.91

* Optional 4.5 inch "AK" is available for 182/184TC frame motors. Contact factory if required. (1) All GP10A Motors except 5HP, 1800RPM & 1.5HP, 900RPM. (4) All GP100A Motors and 10HP, 3600RPM & 10HP, 1800RPM GP10A Motors. (2) All GP100A Motors and 5HP, 1800RPM & 1.5HP, 900RPM GP10A Motors. (5) All GP10A Motors. (3) All GP10A Motors except 10HP, 3600RPM & 10HP, 1800RPM. (6) All GP100A Motors. Dimensions in inches Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

8-5

INVERTER Duty Severe Duty

General Purpose - TEFC Motors

GP10/GP100 (Cast Iron Frame)

GP10/GP100 (Cast Iron Frame)

INVERTER Duty Severe Duty

General Purpose - TEFC Motors

D-Flange with Feet INVERTER Duty Hazardous Duty

C

AB

C

INVERTER Duty Hazardous Duty

Footed

ÿ BF

AH

AB

BB min. CC

CC

J ÿA

CB AF

øBD

øAK

D

øU

O

AF

G_

CB

D

øU

O

øP

Lead Time

Lead Time

ES

øP

ES

G_

øH K

øH

2F

2 F1

2E

N -W

2 F1

J

BA

J

N -W

2E

BA

Modifications Accessories

Modifications Accessories

AC

AA

K

AC

AA

2F

A

B

D-Flange without Feet

A

B

C

C-Face with Feet

AH

AB

C

AB

AH_

BF CC

Typical Performance

BB min.

Typical Performance

ÿ BF

BB min.

CC

J_ ÿA

ES

AF

AF

CB

øU

øBD

øAK

øP

CB

øAK

øBD

G_

Dimensions

Dimensions

D

S

øU

O

øP

Keyseat detail

ÿ AJ

ES

øH

2F 2 F1

AC

AA

K

J

BA

R

AC

AA

N -W

2E

N -W

A

B

C-Face

C-Face without Feet C AH_

AB

BF

BB min. CC

J_ ÿA

ES

Frame

C

D

2E

2F

143T

14.4

3.5

5.5

4

145T

14.4

3.5

5.5

182T

16.7

4.5

7.5

184T

16.7

4.5

7.5

213T

20.7

5.25

8.5

215T

20.7

5.25

8.5

254T

26.16 6.25

10

256T

26.16 6.25

10

2F1 5

4.5 5.5 5.5 7 8.25 10

N-W

O

P

U

AB

BA

AH

AJ

2.25

7.5

7.6

0.875

6.9

2.25

2.12 5.875

2.25

7.5

7.6

0.875

6.9

2.25

2.75

11.1

9.6

1.125

7.8

2.75

2.75

11.1

9.6

1.125

7.8

3.38 10.66

10.7

1.375

3.38 10.66

10.7

1.375

D-Flange BF

AH

AJ

AK

BD

Keyseat

AK

BD

BF

R

4.5

6.6 3/8-16 2.25

10

9 10.9 0.53 0.771 0.188 1.41

S

ES

2.12 5.875

4.5

6.6 3/8-16 2.25

10

9 10.9 0.53 0.771 0.188 1.41

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

2.75

2.62

7.25

8.5*

8.9 1/2-13 2.75

10

9

11

0.53 0.986 0.25

1.81

9.45

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

10

9 10.9 0.53 1.201 0.312 2.44

9.45

10

9 10.9 0.53 1.201 0.312 2.44

3.5

3.12

7.25

8.5

8.9 1/2-13 3.38

4

12.75 12.91 1.625 10.197 4.25

3.75

7.25

8.5

9.3 1/2-13

4

12.5 11 13.9 0.81 1.416 0.375 2.91

4

12.75 12.91 1.625 10.197 4.25

3.75

7.25

8.5

9.3 1/2-13

4

12.5 11 13.9 0.81 1.416 0.375 2.91

Dimensions in inches Dimensions are for reference only.

AF

CB

ø BD

øU

øP

ø AK

* Optional 4.5 inch "AK" is available for 182/184TC frame motors. Contact factory if required.

N -W

8-6

2007 Low Voltage AC Motors Selection and Pricing Guide

AA

AC

2007 Low Voltage AC Motors Selection and Pricing Guide

8-7

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

SD10/SD100

SD10/SD100

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

D-Flange with Feet INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Footed

C

C

AB

AB

AH

ÿ BF

BB min. CC CC

J ÿA

øBD

G_

G_

D

D

AF

øU

øAK

øP

AF

O

CB øU

O

øP

Lead Time

Lead Time

CB

ES

ES

øH

øH K 2F

2E

AC

AA

K

N -W

2 F1

J 2F

J 2E

N -W

Modifications Accessories

Modifications Accessories

AC

AA

BA

2 F1

A

B

BA

A

B

C-Face with Feet C

AB

D-Flange without Feet

BF

AH_ BB min.

C

AB

CC

ÿ BF

Typical Performance

Typical Performance

AH BB min.

J_ ÿA CC

CB AF

øBD

øAK

AF

øU

Dimensions

N -W

Dimensions

2F 2 F1

AC

AA

S

øP

CB

D G_ øH K

Keyseat detail

ÿ AJ

ES

øBD

øAK øU

øP

O

ES

J 2E

BA

A

B

C-Face without Feet

R

AC

AA

N -W

C

AB

AH_

BF C-Face

BB min. CC

J_ ÿA

AF

CB

ø BD

øU

øP

ø AK

ES

Frame

C

D

2E

2F

143T

14.15

3.5

145T

14.15

3.5

5.5

182T

16.4

4.5

7.5 4.5

184T

16.4

4.5

7.5

213T

20.2

5.25

8.5 5.5

215T

20.2

5.25

8.5

254T

25.77

6.25 10

256T

25.77

6.25 10

2F1 N-W(1)

5.5 4 5 5.5 7 8.25 10

O

P

U

AB

BA

AH

2.25

7.5

8.2

0.875

7.4

2.25

2.25

AJ

D-Flange BF

AH

AJ

AK

BD

Keyseat

AK

BD

BF

R

2.12 5.875

4.5

6.6 3/8-16 2.25 10

9

10.9 0.53 0.771 0.188 1.41

S

ES

7.5

8.2

0.875

7.4

2.25

2.12 5.875

4.5

6.6 3/8-16 2.25 10

9

10.9 0.53 0.771 0.188 1.41

2.75 11.1

9.6

1.125

8.2

2.75

2.62 7.25

8.5* 8.9 1/2-13 2.75 10

9

11

0.53 0.986 0.25

1.81

2.75 11.1

9.6

1.125

8.2

2.75

2.62 7.25

8.5* 8.9 1/2-13 2.75 10

9

11

0.53 0.986 0.25

1.81

3.38 10.66 10.7

1.375 10.39

3.5

3.12 7.25

8.5

8.9 1/2-13 3.38 10

9

10.9 0.53 1.201 0.312 2.44

3.38 10.66 10.7

1.375 10.39

9

10.9 0.53 1.201 0.312 2.44

3.5

3.12 7.25

8.5

8.9 1/2-13 3.38 10

4

12.75 12.91 1.625 11.14

4.25

3.75 7.25

8.5

9.3 1/2-13 4

12.5 11 13.9 0.81 1.416 0.375 2.91

4

12.75 12.91 1.625 11.14

4.25

3.75 7.25

8.5

9.3 1/2-13 4

12.5 11 13.9 0.81 1.416 0.375 2.91

* Optional 4.5 inch "AK" is available for 182/184TC frame motors. Contact factory if required. (1) Not according to NEMA standard for SD100 IEEE841 motors due to Inpro/Seal® bearing isolator.

AA N -W

8-8

2007 Low Voltage AC Motors Selection and Pricing Guide

AC Dimensions in inches Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

8-9

INVERTER Duty Severe Duty

RGZP / RGZPSD / RGZESD / RGZTESD / RGZZESD C-Face with and without Feet

Lead Time

Typical Performance Dimensions

R .77 .77

ES 1.38 1.38

C 12.2 13.3

D 3.50 3.50

E 2.75 2.75

2F 4 5

BA 2.25 2.25

N-W 2.25 2.25

O 6.93 6.93

P 7.7 7.7

182T 184T

.250 .250

.99 .99

1.75 1.75

14.2 15.2

4.50 4.50

3.75 3.75

4.50 5.50

2.75 2.75

2.75 2.75

8.86 8.86

9.7 9.7

213T 215T

.313 .313

1.20 1.20

2.38 2.38

18.0 19.1

5.25 5.25

4.25 4.25

5.50 7

3.50 3.50

3.38 3.38

10.62 10.62

11.2 11.2

254T 256T

.375 .375

1.42 1.42

2.88 2.88

22.3 24.1

6.25 6.25

5 5

8.25 10

4.25 4.25

4 4

12.62 12.62

13.4 13.4

284T 286T

.500 .500

1.59 1.59

3.25 3.25

27.4 28.9

7 7

5.50 5.50

9.50 11

4.75 4.75

4.63 4.63

14.19 14.19

15.5 15.5

284TS 286TS

.375 .375

1.42 1.42

1.88 1.88

26.0 27.5

7 7

5.50 5.50

9.50 11

4.75 4.75

3.25 3.25

14.19 14.19

15.5 15.5

324T 326T

.500 .500

1.85 1.85

3.88 3.88

32.0 32.0

8 8

6.25 6.25

10.50 12

5.25 5.25

5.25 5.25

15.94 15.94

17.1 17.1

324TS 326TS

.500 .500

1.59 1.59

2 2

30.0 30.0

8 8

6.25 6.25

10.50 12

5.25 5.25

3.75 3.75

15.94 15.94

17.1 17.1

364T 365T

.625 .625

2.02 2.02

4.25 4.25

34.2 34.2

9 9

7 7

11.25 12.25

5.88 5.88

5.88 5.88

17.81 17.81

18.5 18.5

364TS 365TS

.500 .500

1.59 1.59

2 2

32.1 32.1

9 9

7 7

11.25 12.25

5.88 5.88

3.75 3.75

17.81 17.81

18.5 18.5

404T 405T

.750 .750

2.45 2.45

5.63 5.63

39.5 39.5

10 10

8 8

12.25 13.75

6.625 6.625

7.25 7.25

19.90 19.90

19.6 19.6

404TS 405TS

.500 .500

1.85 1.85

2.75 2.75

36.5 36.5

10 10

8 8

12.25 13.75

6.625 6.625

4.25 4.25

19.90 19.90

19.6 19.6

444T 445T

.875 .875

2.88 2.88

6.88 6.88

45.6 45.6

11 11

9 9

14.50 16.50

7.50 7.50

8.50 8.50

21.9 21.9

21.7 21.7

444TS 445TS

.625 .625

2.02 2.02

3 3

41.8 41.8

11 11

9 9

14.50 16.50

7.50 7.50

4.75 4.75

21.9 21.9

21.7 21.7

447T 447TS 449T 449TS S449LS S449SS

.875 .625 .875 .625 .875 .625

2.88 2.02 2.88 2.02 3.13 2.28

6.88 3 6.88 3 7.5 3.5

49.1 45.4 54.1 50.3 67.1 67.1

11 11 11 11 11 11

9 9 9 9 9 9

20 20 25 25 25 25

7.50 7.50 7.50 7.50 7.50 7.50

8.50 4.75 8.50 4.75 9.12 5.25

21.9 21.9 21.9 21.9 23.4 23.4

21.8 21.8 21.8 21.8 25.4 25.4

AB U 6.46 .875 6.46 +.0000 –.0005 7.36 1.125 7.36 +.0000 –.0005 9.02 1.375 9.02 +.0000 –.0005 9.92 1.625 9.92 +.000 –.001 13.4 1.875 13.4 +.000 –.001 13.4 1.625 13.4 +.000 –.001 15.75 2.125 15.75 +.000 –.001 15.75 1.875 15.75 +.000 –.001 17.69 2.375 17.69 +.000 –.001 17.69 1.875 17.69 +.000 –.001 17.50 2.875 17.50 +.000 –.001 17.50 2.125 17.50 +.000 –.001 19.94 3.375 19.94 +.000 –.001 19.94 2.375 19.94 +.000 –.001 19.94 3.375 19.94 2.375 22.00 3.375 22.00 2.375 23.01 3.625 23.01 2.625

Frame 143/5TC 182/4TC

BD 6.50 9.00*

AJ 5.875 7.250*

AK 4.5 8.5*

U 0.875 1.125

AH 2.12 2.62

ES 1.41 1.78

S .188 .250

BF# 4 4

BF DIA *** ***

213/5TC

9.00

7.250

8.5

1.375

3.12

2.41

.312

4

***

254/6TC

10.00

7.250

8.5

1.625

3.75

2.91

.375

4

***

284/6TC

10.75

9.000

10.5

1.875

4.38

3.25

.500

4

***

284/6TSC

10.75

9.00

10.5

1.625

3.00

1.88

.380

4

***

324/6TC

12.75

11.00

12.5

2.125

5.00

3.88

.500

4

***

324/6TSC

12.75

11.00

12.5

1.875

3.50

2.00

.500

4

***

364/5TC

12.75

11.00

12.5

2.375

5.62

4.25

.625

8

***

364/5TSC

12.75

11.00

12.5

1.875

3.50

2.00

.500

8

***

404/5TC

13.50

11.00

12.5

2.875

7.00

5.62

.750

8

***

404/5TSC

13.50

11.00

12.5

2.125

4.00

2.75

.500

8

***

444/5TC

16.62

14.00

16.0

3.375

8.25

6.88

.875

8

***

444/5TSC

16.62

14.00

16.0

2.375

4.50

3.00

.625

8

***

447TC

16.62

14.00

16.0

3.375

8.25

6.88

.875

8

***

447TSC

16.62

14.00

16.0

2.375

4.50

3.00

.625

8

***

449TC

16.62

14.00

16.0

3.375

8.25

6.88

.875

8

***

449TSC

16.62

14.00

16.0

2.375

4.50

3.00

.625

8

***

* Optional 4.5 inch “AK” (See 143/5TC) is available for 182/4 TC. Contact factory if required. ***Tap for 449TC to 324TC = .625 - 11. For 286TC to 182TC = .500 - 13. 140TC = .375 - 16 NC. Drip Cover dimension (when used) - max 3 inches. Dimensions in inches Dimensions are for reference only.

Dimensions in inches Dimensions are for reference only.

8-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-11

Dimensions

S .188 .188

Typical Performance

NEMA Frame 143T 145T

Modifications Accessories

Modifications Accessories

Lead Time

INVERTER Duty Hazardous Duty

RGZP / RGZPSD / RGZESD / RGZTESD / RGZZESD

INVERTER Duty Hazardous Duty

General Purpose, Severe & Hazardous Duty- TEFC Motors

INVERTER Duty Severe Duty

General Purpose, Severe & Hazardous Duty- TEFC Motors

INVERTER Duty Severe Duty

Automotive Duty - TEFC U-Frame Motors RGZEAD

RGZP / RGZPSD / RGZESD / RGZTESD / RGZZESD D-Flange with and without Feet

INVERTER Duty Hazardous Duty Lead Time

Typical Performance

S 0.188

184

0.188

213

0.25

215

0.25

254U

R 0.771

ES 1.41

C 14.3

D 4.5

0.771

1.41

15.35

4.5

0.986

2.04

17.8

5.25

0.986

2.04

19.3

5.25

0.312

1.201

2.8

22.9

256U

0.312

1.201

2.8

284U

0.375

1.416

286U

0.375

1.416

324S

0.375

326S

E 3.75

BA 2.75

N-W 2.25

O 9

P 9

AB 8

U 0.875

3.75

5.5

2.75

2.25

9

4.25

5.5

3.5

3

10.62

9

8

0.875

10.63

9.4

4.25

7

3.5

3

10.62

10.63

9.4

1.125 1.125

6.25

5

8.25

4.25

3.75

12.62

12.65

10.65

1.375

24.61

6.25

5

10

4.25

3.75

12.62

12.65

10.65

1.375

3.74

27.6

7

5.5

9.5

4.74

4.88

14.27

14.38

13.39

1.625

3.74

29.2

7

5.5

11

4.74

4.88

14.27

14.38

13.39

1.625

1.416

1.875

29.48

8

6.25

10.5

5.25

3.25

15.9

15.82

15.5

1.625

0.375

1.416

1.875

29.48

8

6.25

12

5.25

3.25

15.9

15.82

15.5

1.625

324U

0.5

1.591

4.24

31.86

8

6.25

10.5

5.25

5.62

15.9

15.82

15.5

1.875

326U

0.5

1.591

4.24

31.86

8

6.25

12

5.25

5.62

15.9

15.82

15.5

1.875

364U

0.5

1.845

5

34.69

9

7

11.25

5.88

6.38

17.81

17.66

17.94

2.125

Frame 143/5TD

BD 11.00

AJ 10.0

AK 9

U .875

AH 2.25

ES 1.41

S .188

BF# 4

BF DIA .530

364US

0.75

1.591

2

32.06

9

7

11.25

5.88

3.75

17.81

17.66

17.94

1.875

182/4TD

11.00

10.0

9

1.125

2.75

1.78

.250

4

.530

365U

0.5

1.845

5

34.69

9

7

12.25

5.88

6.38

17.81

17.66

17.94

2.125

213/5TD

11.00

10.0

9

1.375

3.38

2.41

.310

4

.530

365US

0.75

1.591

2

32.06

9

7

12.25

5.88

3.75

17.81

17.66

17.94

1.875

.812

404U

0.625

2.021

5.5

39.28

10

8

12.25

6.62

7.125

19.6

19.56

18.38

2.375

.812

404US

0.5

1.845

2.75

36.4

10

8

12.25

6.62

4.25

19.6

19.56

18.38

2.125

0.625

2.021

5.5

39.28

10

8

13.75

6.62

7.125

19.6

19.56

18.38

2.375

254/6TD

14.00

284/6TD

13.88

12.5 12.5

11 11

1.625 1.875

4.00 4.62

2.91 3.25

.375 .500

4 4

284/6TSD

13.88

12.5

11

1.625

3.25

1.88

.375

4

.812

405U

324/6TD

17.88

16.0

14

2.125

5.25

3.88

.500

4

.812

405US

0.5

1.845

2.75

36.4

10

8

13.75

6.62

4.25

19.6

19.56

18.38

2.125

324/6TSD

17.88

16.0

14

1.875

3.75

2.00

.500

4

.812

444U

0.75

2.45

7

45.64

11

9

14.5

7.5

8.62

21.8

21.75

19.63

2.875

364/5TD

17.88

16.0

14

2.375

5.88

4.25

.620

4

.812

445U

0.75

2.45

7

45.64

11

9

16.5

7.5

8.62

21.8

21.75

19.63

2.875

364/5TSD

17.88

16.0

14

1.875

3.75

2.00

.500

4

.812

All of the above motors have 8 hole footprints except 182 to 286 frames.

404/5TD

21.88

20.0

18

2.875

7.25

5.62

.750

8

.812

Dimensions in inches Dimensions are for reference only.

404/5TSD

21.88

20.0

18

2.125

4.25

2.75

.500

8

.812

444/5TD

21.88

20.0

18

3.375

8.50

6.88

.875

8

.812

444/5TSD

21.88

20.0

18

2.375

4.75

3.00

.625

8

.812

447TD

21.88

20.0

18

3.375

8.50

6.88

.875

8

.812

447TSD

21.88

20.0

18

2.375

4.75

3.00

.625

8

.812

449TD

21.88

20.0

18

3.375

8.50

6.88

.875

8

.812

449TSD

21.88

20.0

18

2.375

4.75

3.00

.625

8

.812

Drip Cover dimension (when used) - max 3 inches. Dimensions in inches Dimensions are for reference only.

8-12

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-13

Dimensions

2F 4.5

Typical Performance

Dimensions

Frame 182

Modifications Accessories

Modifications Accessories

Lead Time

INVERTER Duty Hazardous Duty

INVERTER Duty Severe Duty

General Purpose, Severe & Hazardous Duty- TEFC Motors

INVERTER Duty Severe Duty

RGZESDB / RGZESBR Brake Motors

RGZVESD / RGZVMTESD / RGZVILESD RGZZVESD / RGZZVMTESD / RGZZVILESD

Lead Time

C 17.28

D —

145T

2.94

—

18.74

—

10

182T

2.94

—

20.28

—

15

184T

2.94

—

21.28

—

20

213T

4.69

.4

26.56

1.3

35

215T

4.69

.4

28.56

1.3

50

254T

4.69

.4

32.58

1.3

75

256T

4.69

.4

34.82

1.3

105

284T

4.69

.4

37.50

1.3

50

284T

4.69

.4

37.50

1.3

75

286T

4.69

.4

39.00

1.3

75

286T

4.69

.4

39.50

1.3

105

324T

4.69

.4

42.50

1.3

105

324T

6.00

—

45.00

1.4

175

326T

4.69

.4

42.5

1.3

105

326T

6.00

—

45.20

1.4

230

364T

6.00

—

48.50

1.4

330

365T

6.00

—

48.50

1.4

330

Frame

Brake Size Lb.Ft

C

FC

X

FAH

FAJ

FAK

FBB

FR

FS

FU

143T

13.22

15.03

6.53

1.81

5.88

4.50

.16

.517

.188

.625

6

145T

14.22

16.03

6.53

1.81

5.88

4.50

.16

.517

.188

.625

10

182T

15.77

18.03

8.03

2.26

5.88

4.50

.16

.771

.188

.875

15

184T

16.77

19.03

8.03

2.26

5.88

4.50

.16

.771

.188

.875

20

213T

19.11

21.87

9.50

2.76

7.25

8.50

—

.986

.250

1.125

35

215T

20.61

23.37

9.50

2.76

7.25

8.50

—

.986

.250

1.125

254T

24.65

28.05

11.55

3.40

7.25

8.50

—

1.201

.312

1.375

256T

26.40

29.80

11.55

3.40

7.25

8.50

—

1.201

.312

284T

29.42

31.75

12.88

2.33

7.25

8.50

—

1.201

286T

30.92

33.25

12.88

2.33

7.25

8.50

—

1.201

Dimensions in inches Dimensions are for reference only.

8-14

2007 Low Voltage AC Motors Selection and Pricing Guide

Frame 143LP

145LP

U 1.125

ES 1.25

EU 0.875

EP 1.160

AH 2.75

AJ 9.12

AK 8.25

BB 0.19

BD 10.00

BF .438

R 0.986

S .250

182LP

184LP

1.125

1.25

0.875

1.160

2.75

9.12

8.25

0.19

10.00

.438

0.986

.250

213LP

215 LP

1.625

1.25

1.250

1.770

2.75

9.12

8.25

0.19

10.00

.438

1.416

.375

254LP

256LP

1.625

1.25

1.250

1.770

2.75

9.12

8.25

0.19

10.00

.438

1.416

.375

284LPH

286LPH

2.125

3.00

1.750

2.360

4.50

14.75

13.50

0.25

16.50

.688

1.845

.500

324LP

326 LP

2.125

3.00

1.750

2.360

4.50

14.75

13.50

0.25

16.50

.688

1.845

.500

364LP

365LP

2.125

3.00

1.750

2.380

4.50

14.75

13.50

0.25

16.50

.688

1.845

.500

404LP

405LP

2.125

3.00

1.750

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.845

.500

444LP

445LP

2.125

3.00

1.750

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.845

.500

447LP

449LP

2.125

3.00

1.750

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.845

.500

143HP

145HP

0.875

1.25

0.688

1.160

2.75

9.12

8.25

0.19

10.00

.438

0.771

.188

182HP

184HP

1.125

1.25

0.875

1.160

2.75

9.12

8.25

0.19

10.00

.438

0.986

.250

213HP

215HP

1.125

1.25

0.875

1.380

2.75

9.12

8.25

0.19

10.00

.438

0.986

.250

254HP

256HP

1.125

1.25

0.875

1.770

2.75

9.12

8.25

0.19

10.00

.438

0.986

.250

284HP

286HP

1.125

1.25

0.875

2.360

2.75

9.12

8.25

0.19

10.00

.438

0.986

.250

284HPH

286HPH

1.625

3.00

1.250

2.360

4.50

14.75

13.50

0.25

16.50

.688

1.416

.375

50

324HP

326HP

1.625

3.00

1.250

2.360

4.50

14.75

13.50

0.25

16.50

.688

1.416

.375

75

364HP

365HP

1.625

3.00

1.250

2.360

4.50

14.75

13.50

0.25

16.50

.688

1.416

.375

1.375

105

404HP

405HP

1.625

3.00

1.250

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.416

.375

.312

1.375

105

444HP

445HP

2.125

3.00

1.750

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.845

.500

.312

1.375

105

447HP

449HP

2.125

3.00

1.750

2.999

4.50

14.75

13.50

0.25

16.38

.688

1.845

.500

Dimensions in inches Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

8-15

Dimensions

Dimensions

Typical Performance

Typical Performance

B —

Modifications Accessories

A 2.94

Lead Time

Modifications Accessories

Brake Size Lb.Ft 6

Frame 143T

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe & Hazardous Duty P-Base (VSS) Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Brake & Brake Ready Motors

INVERTER Duty Severe Duty

HSRGZVESD

INVERTER Duty Severe Duty

Severe Duty P-Base (VHS) Motors

Severe Duty - TEFC Motors HIGH | Efficient

P

RGZEESD

EO

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

View "X" AB AC

56?

AA N.P.T. AG

CD

AF

CH 90? BV

Lead Time Modifications Accessories

AJ

AK BD

"BF" HOLES EQL. SP.

"X"

(npt) 1.5

AB 11.2

AC 9.2

AF 8.23

AG 30.5

AJ 9.125

BF AK 8.25

BF BD 10

286TP 14.1

1.5

11.2

9.2

8.23

30.5

9.125

8.25

10

0.44

324TP 15.8

2

12.5

10.2

9.68

32.6

14.75

13.5

16.5

326TP 15.8

2

12.5

10.2

9.68

32.6

14.75

13.5

16.5

364TP 17.7

3

15.3

12.1

11.53

37.6

14.75

13.5

365TP 17.7

3

15.3

12.1

11.53

37.6

14.75

404TP 19.8

3

17

13.9

11.53

43.1

17

13.9

11.53

43.1

(dia) #Holes 0.44 4

BV 6.02

CD 25.1

CH 6.85

CP 3.66

EO 5.7

4

6.02

26.6

6.85

3.66

5.7

0.69

4

7

31

7.87

4.41

4.1

0.69

4

7

31

7.87

4.41

4.1

16.5

0.69

4

8.15

34.8

9.21

6.22

4.6

13.5

16.5

0.69

4

8.15

34.8

9.21

6.22

4.6

14.75

13.5

16.5

0.69

4

8.5

40

9.21

6.22

6.4

40

9.21

405TP 19.8

3

14.75

13.5

16.5

0.69

4

8.5

6.22

6.4

444TP 22.2

3

19.94 15.06 12.31

49.54 14.75

13.5

19.8

0.69

4

16.75

43.2

10.5

9

6.34

445TP 22.2

3

19.94 15.06 12.31

49.54 14.75

13.5

19.8

0.69

4

16.75

43.2

10.5

9

6.34

447TP 22.2

3

19.94 15.06 12.31

53.04 14.75

13.5

19.8

0.69

4

20.25

46.7

10.5

9

6.34

449TP 22.2

3

19.94 15.06 12.31

58.04 14.75

13.5

19.8

0.69

4

25.25

51.7

10.5

9

6.34

Frame 284

BX 1.001

286 324

E 0.250

F 1.141

G 2.52

Stocked Motors HP RPM 25 1800

BY (tap) 10-32NF

BZ 1.375

1.001

10-32NF

1.375

0.250

1.141

2.52

30

1800

1.188

0.250-20NC

1.75

0.250

1.328

2.87

40

1800

326

1.188

0.250-20NC

1.75

0.250

1.328

2.87

50

1800

364-365

1.188

0.250-20NC

1.75

0.250

1.328

2.87

60, 75

1800

364-365

1.501

0.250-20NC

2.125

0.375

1.679

2.87

364-365

1.251

0.250-20NC

1.75

0.375

1.424

2.87

364-365

1.001

10-13NF

1.375

0.250

1.124

2.87

364-365

1.438

0.250-20NC

2.125

0.375

1.615

2.87

404-405

1.251

0.250-20NC

1.75

0.375

1.424

2.87

404-405

1.438

0.250-20NC

2.125

0.375

1.615

2.87

404-405

1.688

0.250-20NC

2.5

0.375

1.869

3.62

404-405

1.188

0.250-20NC

1.75

0.250

1.328

2.52

404-405

1.501

0.250-20NC

2.125

0.375

1.679

2.87

444-449

1.688

0.250-20NC

2.5

0.375

1.901

2.52

"BY" HOLES (4) EQL. SP.

BZ

E F

G BX

1800 Detail of Drive Coupling

100

1800

Poles 2,4,6 2,4,6 2 4,6 2 4,6 2 4,6 2 4,6 2 4,6 2 4,6 4,6 4,6 2 4,6 2 4,6 4,6 4,6 2 4,6 2 4,6 4,6 4,6 2 4,6 2 4,6

S 0.188 0.188 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.312 0.375 0.375 0.375 0.375 0.500 0.500 0.375 0.375 0.375 0.375 0.5 0.5 0.5 0.5 0.5 0.5 0.625 0.625 0.5 0.5 0.5 0.5

R 0.771 0.771 0.986 0.986 0.986 0.986 1.201 1.201 1.201 1.201 1.416 1.416 1.416 1.416 1.591 1.591 1.416 1.416 1.416 1.416 1.845 1.845 1.591 1.591 1.591 1.591 2.021 2.021 1.591 1.591 1.591 1.591

ES 1.41 1.41 1.78 1.78 1.78 1.78 2.41 2.41 2.41 2.41 2.91 2.91 2.91 2.91 3.25 3.25 1.88 1.88 1.88 1.88 3.88 3.88 2 2 2 2 4.25 4.25 2 2 2 2

C 13.97 13.97 14.8 16.22 15.9 16.22 18.15 20.27 19.7 20.27 23.15 25.83 24.85 25.83 29.38 29.38 26 28.01 27.5 28.01 32.07 32.07 30 30.57 30 30.57 35.53 35.53 32.06 33.4 32.06 33.4

D 3.50 3.50 4.50 4.50 4.50 4.50 5.25 5.25 5.25 5.25 6.25 6.25 6.25 6.25 7 7 7 7 7 7 8 8 8 8 8 8 9 9 9 9 9 9

E 2.75 2.75 3.75 3.75 3.75 3.75 4.25 4.25 4.25 4.25 5 5 5 5 5.5 5.5 5.5 5.5 5.5 5.5 6.25 6.25 6.25 6.25 6.25 6.25 7 7 7 7 7 7

2F 4.0 5.0 4.5 4.5 5.5 5.5 5.5 5.5 7.0 7.0 8.25 8.25 10 10 9.5 11 9.5 9.5 11 11 10.5 12 10.5 10.5 12 12 11.25 12.25 11.25 11.25 12.25 12.25

BA 2.25 2.25 2.75 2.75 2.75 2.75 3.5 3.5 3.5 3.5 4.25 4.25 4.25 4.25 4.75 4.75 4.75 4.75 4.75 4.75 5.25 5.25 5.25 5.25 5.25 5.25 5.88 5.88 5.88 5.88 5.88 5.88

N-W 2.25 2.25 2.75 2.75 2.75 2.75 3.38 3.38 3.38 3.38 4 4 4 4 4.625 4.625 3.25 3.25 3.25 3.25 5.25 5.25 3.75 3.75 3.75 3.75 5.88 5.88 3.75 3.75 3.75 3.75

O 7.56 7.56 9 9.74 9 9.74 10.43 11.35 10.43 11.35 12.33 13.34 12.33 13.34 14.87 14.87 14.27 14.87 14.27 14.87 16.66 16.66 15.9 16.66 15.9 16.66 18.48 18.48 17.81 18.48 17.81 18.48

P 8.11 8.11 9 10.83 9 10.83 10.63 12.2 10.63 12.2 12.65 14.37 12.65 14.37 15.82 15.82 14.38 15.82 14.38 15.82 17.66 17.66 15.82 17.66 15.82 17.66 19.56 19.56 17.66 19.56 17.66 19.56

AB 7.05 7.05 8 8.58 8 8.58 9.4 10.63 9.4 10.63 10.65 11.62 10.65 11.62 14.3 14.3 13.39 14.33 13.39 14.33 15.99 15.99 15.5 15.99 15.5 15.99 18.57 18.57 17.94 18.57 17.94 18.57

U 0.875 0.875 1.125 1.125 1.125 1.125 1.375 1.375 1.375 1.375 1.625 1.625 1.625 1.625 1.875 1.875 1.625 1.625 1.625 1.625 2.125 2.125 1.875 1.875 1.875 1.875 2.375 2.375 1.87 1.875 1.875 1.875

All of the above motors have 8 hole footprints except 182 to 286 frames (2 pole only) and S449 frames. Dimensions in inches Dimensions are for reference only.

*

1800

* 125, 150, 200 & 250 HP Dimensions in inches Dimensions are for reference only.

8-16

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-17

Dimensions

Detail of Drive Coupling

Frame 143T 145T 182T 182T 184T 184T 213T 213T 215T 215T 254T 254T 256T 256T 284T 286T 284TS 284TS 286TS 286TS 324T 326T 324TS 324TS 326TS 326TS 364T 365T 364TS 364TS 365TS 365TS

Typical Performance

AA Frame P 284TP 14.1

Modifications Accessories

Typical Performance

Lead Time

Dimensions

CP

BE

INVERTER Duty Severe Duty

RGZEESD

RGZEESDX

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe Duty / IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Typical Performance

ES 5.63 5.63 2.75 2.75 6.88 6.88 3.05 3.05 6.88 3.05 6.88 3.05 7.5 3.5 3.5

C 39.4 39.4 36.4 36.4 45.58 45.58 41.82 41.82 49 45.26 54 50.3 63.6 59.8 63.2

D 10 10 10 10 11 11 11 11 11 11 11 11 11 11 11

E 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9

2F 12.25 13.75 12.25 13.75 14.5 16.5 14.5 16.5 20 20 25 25 25 25 25

* Only for 400HP, 2 Pole All of the above motors have 8 hole footprints except 182 to 286 frames (2 pole only) and S449 frames. Dimensions in inches Dimensions are for reference only.

BA 6.62 6.62 6.62 6.62 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5

N-W 7.25 7.25 4.25 4.25 8.5 8.5 4.75 4.75 8.5 4.75 8.5 4.75 9.12 5.25 5.25

O 19.6 19.6 19.6 19.6 21.8 21.8 21.8 21.8 22 22 22 22 23.3 23.3 23.3

P 19.56 19.56 19.56 19.56 21.75 21.75 21.75 21.75 21.75 21.75 21.75 21.75 24.6 24.6 24.6

AB 18.38 18.38 18.38 18.38 19.63 19.63 19.63 19.63 19.63 19.63 22 22 23 23 23

U 2.875 2.875 2.125 2.125 3.375 3.375 2.375 2.375 3.375 2.375 3.375 2.375 3.625 2.625 2.625

Frame Poles 143T 2,4,6,8 145T 2,4,6,8 182T 2,8 182T 4,6 184T 2,8 184T 4,6 213T 2,8 213T 4,6 215T 2,8 215T 4,6 254T 2,8 254T 4,6 256T 2,8 256T 4,6 284T 8 284T 4,6 286T 8 286T 4,6 284TS 2,8 284TS 4,6 286TS 2,8 286TS 4,6 324T 8 324T 4,6 326T 8 326T 4,6 324TS 2 324TS 4,6 326TS 2 326TS 4,6

S 0.188 0.188 0.250 0.250 0.250 0.250 0.312 0.312 0.312 0.312 0.375 0.375 0.375 0.375 0.500 0.500 0.500 0.500 0.375 0.375 0.375 0.375 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

R 0.771 0.771 0.986 0.986 0.986 0.986 1.201 1.201 1.201 1.201 1.416 1.416 1.416 1.416 1.591 1.591 1.591 1.591 1.416 1.416 1.416 1.416 1.845 1.845 1.845 1.845 1.591 1.591 1.591 1.591

ES 1.41 1.41 1.78 1.78 1.78 1.78 2.41 2.41 2.41 2.41 2.91 2.91 2.91 2.91 3.25 3.25 3.25 3.25 1.88 1.88 1.88 1.88 3.88 3.88 3.88 3.88 2 2 2 2

C 13.97 13.97 14.8 16.22 15.9 16.22 18.15 20.27 19.7 20.27 23.15 25.83 24.85 25.83 27.4 29.38 28.9 29.38 26 28.01 27.5 28.01 31.5 32.07 31.5 32.07 30 30.57 30 30.57

D 3.50 3.50 4.50 4.50 4.50 4.50 5.25 5.25 5.25 5.25 6.25 6.25 6.25 6.25 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8

E 2.75 2.75 3.75 3.75 3.75 3.75 4.25 4.25 4.25 4.25 5 5 5 5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 6.25 6.25 6.25 6.25 6.25 6.25 6.25 6.25

2F 4.0 5.0 4.5 4.5 5.5 5.5 5.5 5.5 7.0 7.0 8.25 8.25 10 10 9.5 9.5 11 11 9.5 9.5 11 11 10.5 10.5 12 12 10.5 10.5 12 12

BA(1) 2.73 2.73 3.03 3.03 3.03 3.03 4 4.03 4 4.03 4.7 4.78 4.7 4.78 5.2 5.29 5.2 5.29 5.2 5.28 5.2 5.28 5.75 5.8 5.75 5.8 5.75 5.75 5.75 5.75

N-W(1) 1.77 1.77 2.46 2.46 2.46 2.46 2.88 2.85 2.88 2.85 3.55 3.47 3.55 3.47 4.17 4.09 4.17 4.09 2.8 2.72 2.8 2.72 4.75 4.69 4.75 4.69 3.25 3.25 3.25 3.25

O 7.42 7.42 9 9.74 9 9.74 10.43 11.35 10.43 11.35 12.33 13.34 12.33 13.34 14.27 14.87 14.27 14.87 14.27 14.87 14.27 14.87 15.9 16.66 15.9 16.66 15.9 16.66 15.9 16.66

P 8.11 8.11 9 10.83 9 10.83 10.63 12.2 10.63 12.2 12.65 14.37 12.65 14.37 14.38 15.82 14.38 15.82 14.38 15.82 14.38 15.82 15.82 17.66 15.82 17.66 15.82 17.66 15.82 17.66

AB 7.05 7.05 8 8.58 8 8.58 9.4 10.63 9.4 10.63 10.65 11.62 10.65 11.62 13.39 14.3 13.39 14.3 13.39 14.33 13.39 14.33 15.5 15.99 15.5 15.99 15.5 15.99 15.5 15.99

U 0.875 0.875 1.125 1.125 1.125 1.125 1.375 1.375 1.375 1.375 1.625 1.625 1.625 1.625 1.875 1.875 1.875 1.875 1.625 1.625 1.625 1.625 2.125 2.125 2.125 2.125 1.875 1.875 1.875 1.875

Dimensions

Dimensions

R 2.45 2.45 1.845 1.845 2.88 2.88 2.021 2.021 2.88 2.021 2.88 2.021 3.134 2.275 2.275

Typical Performance

S 0.75 0.75 0.5 0.5 0.875 0.875 0.625 0.625 0.875 0.625 0.875 0.625 0.875 0.625 0.625

Modifications Accessories

Modifications Accessories

Lead Time

Lead Time

Frame Poles 404T 405T 404TS 405TS 444T 445T 444TS 445TS 447T 447TS 449T 449TS S449LS S449SS S449SS *

(1) Not according to NEMA standard. All of the above motors have 8 hole footprints except 182 to 286 frames (2 & 8 pole only) and S449 frames. Dimensions in inches Dimensions are for reference only.

8-18

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-19

INVERTER Duty Severe Duty

RGZEESDX

RGZEESD / RGZEESDX C-Face with and without Feet

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe Duty & IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty / IEEE 841 - TEFC Motors

Typical Performance Dimensions

ES 4.25 4.25 4.25 4.25 2 2 2 2 5.63 5.63 2.75 2.75 6.88 6.88 3.05 3.05 6.88 3.05 6.88 3.05 7.5 7.5 3.5 3.5

C 34.19 35.53 34.19 35.53 32.06 33.4 32.06 33.4 39.4 39.4 36.4 36.4 45.58 45.58 41.82 41.82 49 45.26 54 50.3 63.6 66.7 59.8 63.2

D 9 9 9 9 9 9 9 9 10 10 10 10 11 11 11 11 11 11 11 11 11 11 11 11

E 7 7 7 7 7 7 7 7 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9 9

2F 11.25 11.25 12.25 12.25 11.25 11.25 12.25 12.25 12.25 13.75 12.25 13.75 14.5 16.5 14.5 16.5 20 20 25 25 25 25 25 25

Not according to NEMA standard. * Only for 400HP, 2 Pole ** Only for 300, 350 & 400HP, 4 Pole All of the above motors have 8 hole footprints except 182 to 286 frames (2 & 8 pole only) and S449 frames. (1)

Dimensions in inches Dimensions are for reference only.

BA(1) 6.31 6.35 6.31 6.35 6.31 6.35 6.31 6.35 7.1 7.1 7.38 7.38 7.9 7.9 8.25 8.25 7.96 8.25 7.96 8.25 7.95 7.95 8.16 8.16

N-W(1) 5.44 5.4 5.44 5.4 3.31 3.28 3.31 3.28 6.78 6.78 3.5 3.5 8.1 8.1 4 4 8.03 4 8.03 4 8.67 8.67 4.59 4.59

O 17.81 18.48 17.81 18.48 17.81 18.48 17.81 18.48 19.6 19.6 19.6 19.6 21.8 21.8 21.8 21.8 22 22 22 22 23.3 23.3 23.3 23.3

P 17.66 19.56 17.66 19.56 17.66 19.56 17.66 19.56 19.56 19.56 19.56 19.56 21.75 21.75 21.75 21.75 21.75 21.75 21.75 21.75 24.6 24.6 24.6 24.6

AB 17.94 18.57 17.94 18.57 17.94 18.57 17.94 18.57 18.38 18.38 18.38 18.38 19.63 19.63 19.63 19.63 19.63 19.63 22 22 23 23 23 23

U 2.375 2.375 2.375 2.375 1.875 1.875 1.875 1.875 2.875 2.875 2.125 2.125 3.375 3.375 2.375 2.375 3.375 2.375 3.375 2.375 3.625 3.625 2.625 2.625

BD 6.5

145TC

2,4,6

6.5

5.875

4.5

0.875

1.96

2.25 (1)

2.73

1.41

0.188

4

3/8"-16NC

182TC

2

9

7.25

8.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

182TC

4,6

9

7.25

8.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

6.5

5.875

4.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC 1/2"-13NC

2

182TCH

4,6

AK 4.5

U 0.875

AH 1.96

RGZEESDX BA(1) 2.73

Poles 2,4,6

182TCH

AJ 5.875

RGZEESD BA 2.25 (1)

Frame 143TC

ES 1.41

S 0.188

BF# 4

BF DIA 3/8"-16NC

6.5

5.875

4.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

184TC

2

9

7.25

8.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

184TC

4,6

9

7.25

8.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

184TCH

2

6.5

5.875

4.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

184TCH

4,6

6.5

5.875

4.5

1.125

2.62

2.75 (1)

3.03

1.78

0.25

4

1/2"-13NC

2.41

0.312

4

1/2"-13NC

213TC

2

9

7.25

8.5

1.375

3.12

3.5 (1)

4

213TC

4,6

9

7.25

8.5

1.375

3.12

3.5 (1)

4.03

2.41

0.312

4

1/2"-13NC

215TC

2

9

7.25

8.5

1.375

3.12

3.5 (1)

4

2.41

0.312

4

1/2"-13NC

215TC

4,6

9

7.25

8.5

1.375

3.12

3.5 (1)

4.03

2.41

0.312

4

1/2"-13NC

254TC

2

10

7.25

8.5

1.625

3.75

4.25 (1)

4.7

2.91

0.375

4

1/2"-13NC

254TC

4,6

10

7.25

8.5

1.625

3.75

4.25 (1)

4.78

2.91

0.375

4

1/2"-13NC

256TC

2

10

7.25

8.5

1.625

3.75

4.25 (1)

4.7

2.91

0.375

4

1/2"-13NC

256TC

4,6

10

7.25

284TC

4,6

11.25

9

286TC

4,6

11.25

9

10.5

1.875

4.38

4.75

5.29

3.25

0.5

4

1/2"-13NC

284TSC

2

11.25

9

10.5

1.625

3

4.75

5.2

1.88

0.375

4

1/2"-13NC

284TSC

4,6

11.25

9

10.5

1.625

3

4.75

5.28

1.88

0.375

4

1/2"-13NC

286TSC

2

11.25

9

10.5

1.625

3

4.75

5.2

1.88

0.375

4

1/2"-13NC

286TSC

4,6

11.25

9

10.5

1.625

3

4.75

5.28

1.88

0.375

4

1/2"-13NC

324TC

4,6

14

11

12.5

2.125

5

5.25

5.75

3.88

0.5

4

5/8"-11NC

326TC

4,6

14

11

12.5

2.125

5

5.25

5.8

3.88

0.5

4

5/8"-11NC

8.5

1.625

3.75

4.25 (1)

4.78

2.91

0.375

4

1/2"-13NC

10.5

1.875

4.38

4.75

5.2

3.25

0.5

4

1/2"-13NC

Not according to NEMA standard. Drip Cover dimension (when used)--max. 3 inches (1)

Dimensions in inches Dimensions are for reference only.

8-20

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-21

Dimensions

R 2.021 2.021 2.021 2.021 1.591 1.591 1.591 1.591 2.45 2.45 1.845 1.845 2.88 2.88 2.021 2.021 2.88 2.021 2.88 2.021 3.134 3.134 2.275 2.275

Typical Performance

S 0.625 0.625 0.625 0.625 0.5 0.5 0.5 0.5 0.75 0.75 0.5 0.5 0.875 0.875 0.625 0.625 0.875 0.625 0.875 0.625 0.875 0.875 0.625 0.625

Modifications Accessories

Modifications Accessories

Lead Time

Lead Time

Frame Poles 364T 8 364T 4,6 365T 8 365T 4,6 364TS 2 364TS 4,6 365TS 2 365TS 4,6 404T 405T 404TS 405TS 444T 445T 444TS 445TS 447T 447TS 449T 449TS S449LS S449LS ** S449SS S449SS *

INVERTER Duty Severe Duty

RGZEESD / RGZEESDX C-Face with and without Feet

RGZEESD / RGZEESDX D-Flange with and without Feet

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe Duty & IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty & IEEE 841 - TEFC Motors

Lead Time

Lead Time

324TSC

4,6

BD 14

AJ 11

AK 12.5

U 1.875

AH 3.5

RGZEESD BA 5.25

RGZEESDX BA(1) 5.75

14

11

12.5

1.875

3.5

5.25

5.75

ES 2

S 0.5

BF# 4

BF DIA 5/8"-11NC

2

0.5

4

5/8"-11NC

326TSC

2

14

11

12.5

1.875

3.5

5.25

5.75

2

0.5

4

5/8"-11NC

326TSC

4,6

14

11

12.5

1.875

3.5

5.25

5.75

2

0.5

4

5/8"-11NC

364TC

4,6

12.75

11

12.5

2.375

5.63

5.88

6.31

4.25

0.625

8

5/8"-11NC

365TC

4,6

12.75

11

12.5

2.375

5.63

5.88

6.35

4.25

0.625

8

5/8"-11NC

364TSC

2

364TSC

4,6

365TSC

2

365TSC

4,6

14

11

12.5

1.875

3.5

5.88

6.31

2

0.5

8

5/8"-11NC

12.75

11

12.5

1.875

3.5

5.88

6.35

2

0.5

8

5/8"-11NC

14

11

12.5

1.875

3.5

5.88

6.31

2

0.5

8

5/8"-11NC

12.75

11

12.5

1.875

3.5

5.88

6.35

2

0.5

8

5/8"-11NC

404TC

15.5

11

12.5

2.875

7

6.62

7.1

5.63

0.75

8

5/8"-11NC

405TC

15.5

11

12.5

2.875

7

6.62

7.1

5.63

0.75

8

5/8"-11NC

404TSC 405TSC

15.5 15.5

11 11

12.5 12.5

2.125 2.125

4 4

6.62 6.62

7.38 7.38

2.75 2.75

0.5 0.5

8 8

5/8"-11NC 5/8"-11NC

444TC

18

14

16

3.375

8.25

7.5

7.9

6.88

0.875

8

5/8"-11NC

445TC

18

14

16

3.375

8.25

7.5

7.9

6.88

0.875

8

5/8"-11NC

444TSC

18

14

16

2.375

4.5

7.5

8.25

3.05

0.625

8

5/8"-11NC

445TSC

18

14

16

2.375

4.5

7.5

8.25

3.05

0.625

8

5/8"-11NC

447TC

18

14

16

3.375

8.25

7.5

7.96

6.88

0.875

8

5/8"-11NC

447TSC

18

14

16

2.375

4.5

7.5

8.25

3.05

0.625

8

5/8"-11NC

449TC

18

14

16

3.375

8.25

7.5

7.96

6.88

0.875

8

5/8"-11NC

449TSC

18

14

16

2.375

4.5

7.5

8.25

3.05

0.625

8

5/8"-11NC

S449LSC S449SSC

18 18

14 14

16 16

3.625 2.625

8.25 4.5

(1) Not according to NEMA standard. Drip Cover dimension (when used) - max. 3 inches. S449 frame motors are only available with feet.

Dimensions in inches Dimensions are for reference only.

8-22

2007 Low Voltage AC Motors Selection and Pricing Guide

7.5 7.5

7.95 8.16

7.5 3.5

0.875 0.625

8 8

5/8"-11NC 5/8"-11NC

AJ 10

AK 4.5

U 0.875

AH

RGZEESD BA 2.25 (1)

RGZEESDX BA(1) 2.73

ES 1.41

S 0.188

BF# 4

BF DIA 0.53

Frame 143TD

Poles 2,4,6

BD 11

145TD

2,4,6

11

10

9

0.875

2

2.25 (1)

2.73

1.41

0.188

4

0.53

182TD

2

11

10

9

1.125

2.5

2.75 (1)

3.03

1.78

0.25

4

0.53

182TD

4,6

11

10

9

1.125

2.5

2.75 (1)

3.03

1.78

0.25

4

0.53

184TD

2

11

10

9

1.125

2.5

2.75 (1)

3.03

1.78

0.25

4

0.53

184TD

4,6

11

10

9

1.125

2.5

2.75 (1)

3.03

1.78

0.25

4

0.53

213TD

2

11

10

9

1.375

3.13

3.5 (1)

4

2.41

0.312

4

0.53

213TD

4,6

11

10

9

1.375

3.13

3.5 (1)

4.03

2.41

0.312

4

0.53

215TD

2

11

10

9

1.375

3.13

3.5 (1)

4

2.41

0.312

4

0.53

215TD

4,6

11

10

9

1.375

3.13

3.5 (1)

4.03

2.41

0.312

4

0.53

254TD

2

14

12.5

11

1.625

3.75

4.25 (1)

4.7

2.91

0.375

4

0.81

254TD

4,6

14

12.5

11

1.625

3.75

4.25 (1)

4.78

2.91

0.375

4

0.81

256TD

2

14

12.5

11

1.625

3.75

4.25 (1)

4.7

2.91

0.375

4

0.81

256TD

4,6

14

12.5

11

1.625

3.75

4.25 (1)

4.78

2.91

0.375

4

0.81

284TD

4,6

14

12.5

11

1.875

4.37

4.75

5.2

3.25

0.5

4

0.81

286TD

4,6

14

12.5

11

1.875

4.37

4.75

5.29

3.25

0.5

4

0.81 0.81

2

284TSD

2

14

12.5

11

1.625

3

4.75

5.2

1.88

0.375

4

284TSD

4,6

14

12.5

11

1.625

3

4.75

5.28

1.88

0.375

4

0.81

286TSD

2

14

12.5

11

1.625

3

4.75

5.2

1.88

0.375

4

0.81

286TSD

4,6

14

12.5

11

1.625

3

4.75

5.28

1.88

0.375

4

0.81

324TD

4,6

18

16

14

2.125

5

5.25

5.75

3.88

0.5

4

0.81

326TD

4,6

18

16

14

2.125

5

5.25

5.8

3.88

0.5

4

0.81

(1) Not according to NEMA standard. Drip Cover dimension (when used)--max. 3 inches

Dimensions in inches Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

8-23

Dimensions

Dimensions

Poles 2

Typical Performance

Typical Performance

Modifications Accessories

Modifications Accessories

Frame 324TSC

INVERTER Duty Severe Duty

RGZESDI / RGZZESDI Figure A Totally Enclosed Fan Cooled

Modifications Accessories Typical Performance

AJ 16

AK 14

U 1.875

AH 3.5

RGZEESD BA 5.25

RGZEESDX BA(1) 5.75

324TSD

4,6

18

16

14

1.875

3.5

5.25

5.75

ES 2

S 0.5

BF# 4

BF DIA 0.81

2

0.5

4

0.81

326TSD

2

18

16

14

1.875

3.5

5.25

5.75

2

0.5

4

0.81

326TSD

4,6

18

16

14

1.875

3.5

5.25

5.75

2

0.5

4

0.81

364TD

4,6

18

16

14

2.375

5.63

5.88

6.31

4.25

0.625

4

0.81

365TD

4,6

18

16

14

2.375

5.63

5.88

6.35

4.25

0.625

4

0.81

364TSD

2

18

16

14

1.875

3.5

5.88

6.31

2

0.5

4

0.81

364TSD

4,6

18

16

14

1.875

3.5

5.88

6.35

2

0.5

4

0.81

365TSD

2

18

16

14

1.875

3.5

5.88

6.31

2

0.5

4

0.81

365TSD

4,6

18

16

14

1.875

3.5

5.88

6.35

2

0.5

4

0.81

22

20

18

2.875

7

6.62

7.1

5.63

0.75

4

0.81

404TD 405TD

22

20

18

2.875

7

6.62

7.1

5.63

0.75

4

0.81

404TSD

22

20

18

2.125

4

6.62

7.38

2.75

0.5

4

0.81

405TSD

22

20

18

2.125

4

6.62

7.38

2.75

0.5

4

0.81

444TD

22

20

18

3.375

8.25

7.5

7.9

6.88

0.875

8

0.81

445TD

22

20

18

3.375

8.25

7.5

7.9

6.88

0.875

8

0.81

444TSD

22

20

18

2.375

4.5

7.5

8.25

3.05

0.625

8

0.81

445TSD

22

20

18

2.375

4.5

7.5

8.25

3.05

0.625

8

0.81

447TD

22

20

18

3.375

8.25

7.5

7.96

6.88

0.875

8

0.81

447TSD

22

20

18

2.375

4.5

7.5

8.25

3.05

0.625

8

0.81

449TD

22

20

18

3.375

8.25

7.5

7.96

6.88

0.875

8

0.81

449TSD

22

20

18

2.375

4.5

7.5

8.25

3.05

0.625

8

0.81

S449LSD

22

20

18

3.625

8.25

7.5

7.95

7.5

0.875

8

0.81

S449SSD

22

20

18

2.625

4.5

7.5

8.16

3.5

0.625

8

0.81

Not according to NEMA standard. Drip Cover dimension (when used) - max. 3 inches. S449 frame motors are only available with feet. (1)

8-24

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions in inches Dimensions are for reference only.

XE 1.38 1.38

C 12.2 13.7

D 3.50 3.50

E 2.75 2.75

2F 4.00 5.00

BA 2.25 2.25

N-W 2.25 2.25

O 7.2 7.2

P 7.7 7.7

W 0.13 0.13

AB 6.7 6.7

182T 184T

0.250 0.250

0.250 0.250

1.80 1.80

14.8 15.8

4.50 4.50

3.75 3.75

4.50 5.50

2.75 2.75

2.75 2.75

9.0 9.0

9.4 9.4

0.13 0.13

8.0 8.0

213T 215T

0.313 0.313

0.313 0.313

2.31 2.31

18.2 19.6

5.25 5.25

4.25 4.25

5.50 7.00

3.50 3.50

3.38 3.38

10.5 10.5

10.8 10.8

0.13 0.13

9.4 9.4

254T 256T

0.375 0.375

0.375 0.375

2.81 2.81

23.0 24.8

6.25 6.25

5.00 5.00

8.25 10.00

4.25 4.25

4.00 4.00

12.6 12.6

13.1 13.1

0.13 0.13

10.7 10.7

284T 286T

0.500 0.500

0.500 0.500

3.25 3.25

27.4 28.9

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

4.63 4.63

14.3 14.3

14.9 14.9

0.13 0.13

13.4 13.4

284TS 286TS

0.375 0.375

0.375 0.375

1.88 1.88

27.5 27.5

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

3.25 3.25

14.3 14.3

14.9 14.9

0.13 0.13

13.4 13.4

324T 326T

0.500 0.500

0.500 0.500

3.88 3.88

31.5 31.5

8.00 8.00

6.25 6.25

5.25 5.25

5.25 5.25

16.0 16.0

16.6 16.6

0.13 0.13

15.5 15.5

324TS 326TS

0.500 0.500

0.500 0.500

2.00 2.00

30.0 30.0

8.00 8.00

6.25 6.25

5.25 5.25

3.75 3.75

16.0 16.0

16.6 16.6

0.13 0.13

15.5 15.5

364T 365T

0.625 0.625

0.625 0.625

4.25 4.25

34.2 34.2

9.00 9.00

7.00 7.00

5.88 5.88

5.88 5.88

17.8 17.8

18.4 18.4

0.38 0.38

18.0 18.0

364TS 365TS

0.500 0.500

0.500 0.500

2.00 2.00

32.1 32.1

9.00 9.00

7.00 7.00

5.88 5.88

3.75 3.75

17.8 17.8

18.4 18.4

0.38 0.38

18.0 18.0

404T 405T

0.750 0.750

0.750 0.750

5.63 5.63

39.5 39.5

10.00 10.00

8.00 8.00

6.625 6.625

7.25 7.25

19.9 19.9

19.6 19.6

0.13 0.13

18.7 18.7

404TS 405TS

0.500 0.500

0.500 0.500

2.75 2.75

36.5 36.5

10.00 10.00

8.00 8.00

6.625 6.625

4.25 4.25

19.9 19.9

19.6 19.6

0.13 0.13

18.7 18.7

444T 445T

0.875 0.875

0.875 0.875

6.88 6.88

45.6 45.6

11.00 11.00

9.00 9.00

7.5 7.5

8.50 8.50

21.9 21.9

21.7 21.7

0.13 0.13

20.0 20.0

444TS 445TS

0.625 0.625

0.625 0.625

3.00 3.00

41.8 41.8

11.00 11.00

9.00 9.00

7.5 7.5

4.75 4.75

21.9 21.9

21.7 21.7

0.13 0.13

20.0 20.0

447T 447TS 449T 449TS S449LS S449SS

0.875 0.625 0.875 0.625 0.875 0.625

0.875 0.625 0.875 0.625 0.875 0.625

6.88 3.00 6.88 3.00 7.50 3.50

49.1 45.4 54.1 50.3 63.7 59.8

11.00 11.00 11.00 11.00 11.00 11.00

9.00 9.00 9.00 9.00 9.00 9.00

10.50 12.00 . 10.50 12.00 . 11.25 12.25 . 11.25 12.25 . 12.25 13.75 . 12.25 13.75 . 14.50 16.50 . 14.50 16.50 . 20.00 20.00 25.00 25.00 25.00 25.00

7.50 7.50 7.50 7.50 7.50 7.50

8.50 4.75 8.50 4.75 9.12 5.25

21.9 21.9 21.9 21.9 23.4 23.4

21.8 21.8 21.8 21.8 25.4 25.4

0.13 0.13 0.13 0.13 0.13 0.13

20.0 20.0 20.0 20.0 23.0 23.0

U 0.875 +0.00 -0.0005 1.125 +0.00 -0.0005 1.375 +0.00 -0.0005 1.625 +0.00 -0.001 1.875 +0.00 -0.001 1.625 +0.00 -0.001 2.125 +0.00 -0.001 1.875 +0.00 -0.001 2.375 +0.00 -0.001 1.875 +0.00 -0.001 2.875 +0.00 -0.001 2.125 +0.00 -0.001 3.375 +0.00 -0.001 2.375 +0.00 -0.001 3.375 2.375 3.375 2.375 3.625 2.625

Dimensions in inches Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

8-25

Dimensions

Dimensions

BD 18

XD 0.188 0.188

Typical Performance

Poles 2

XC 0.188 0.188

Modifications Accessories

Frame 324TSD

143T 145T

Lead Time

Lead Time

INVERTER Duty Hazardous Duty

RGZEESD / RGZEESDX D-Flange with and without Feet

INVERTER Duty Hazardous Duty

Severe & Hazardous Duty Motors

INVERTER Duty Severe Duty

Severe Duty & IEEE 841 - TEFC Motors

INVERTER Duty Severe Duty

RGZESDI Figure B Totally Enclosed Blower Cooled with or without Encoder

RGZESDI Figure C Motor with Lake Shore SL56 Encoder

INVERTER Duty Hazardous Duty

INVERTER Duty Hazardous Duty

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

Typical Performance Dimensions

C

D

E

2F

BA

N-W

O

P

W

2.88 2.88

38.0 39.8

6.25 6.25

5.00 5.00

8.25 10.00

4.25 4.25

4.00 4.00

12.62 12.62

13.40 13.40

0.13 0.13

10.7 10.7

284T 286T

0.500 0.500

0.500 0.500

3.25 3.25

41.7 43.2

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

4.63 4.63

14.19 14.19

15.50 15.50

0.13 0.13

13.4 13.4

284TS 286TS

0.375 0.375

0.375 0.375

1.88 1.88

40.3 41.8

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

3.25 3.25

14.19 14.19

15.50 15.50

0.13 0.13

13.4 13.4

324T 326T

0.500 0.500

0.500 0.500

3.88 3.88

45.9 45.9

8.00 8.00

6.25 6.25

10.5 12.00

5.25 5.25

5.25 5.25

15.94 15.94

17.10 17.10

0.13 0.13

15.5 15.5

324TS 326TS

0.500 0.500

0.500 0.500

2.00 2.00

44.4 44.4

8.00 8.00

6.25 6.25

5.25 5.25

3.75 3.75

15.94 15.94

17.10 17.10

0.13 0.13

15.5 15.5

364T 365T

0.625 0.625

0.625 0.625

4.25 4.25

48.6 48.6

9.00 9.00

7.00 7.00

5.88 5.88

5.88 5.88

17.81 17.81

18.50 18.50

0.26 0.26

18.0 18.0

364TS 365TS

0.500 0.500

0.500 0.500

2.00 2.00

46.5 46.5

9.00 9.00

7.00 7.00

5.88 5.88

3.75 3.75

17.81 17.81

18.50 18.50

0.26 0.26

18.0 18.0

404T 405T

0.750 0.750

0.750 0.750

5.63 5.63

53.0 53.0

10.00 10.00

8.00 8.00

6.625 6.625

7.25 7.25

19.90 19.90

19.60 19.60

0.13 0.13

18.7 18.7

404TS 405TS

0.500 0.500 0.500 0.500

2.75 2.75

50.0 50.0

10.00 10.00

8.00 8.00

6.625 6.625

4.25 4.25

19.90 19.90

19.60 19.60

0.13 0.13

18.7 18.7

444T 445T

0.875 0.875

0.875 0.875

6.88 6.88

78.5 78.5

11.00 11.00

9.00 9.00

7.50 7.50

8.50 8.50

21.90 21.90

21.70 21.70

0.13 0.13

20.0 20.0

444TS 445TS

0.625 0.625

0.625 0.625

3.00 3.00

74.8 74.8

11.00 11.00

9.00 9.00

7.50 7.50

4.75 4.75

21.90 21.90

21.70 21.70

0.13 0.13

20.0 20.0

447T 447TS 449T 449TS S449LS S449SS

0.875 0.625 0.875 0.625 0.875 0.625

0.875 0.625 0.875 0.625 0.875 0.625

6.88 3.00 6.88 3.00 7.50 3.50

82.0 78.3 87.1 83.2 100.0 96.1

11.00 11.00 11.00 11.00 11.00 11.00

9.00 9.00 9.00 9.00 9.00 9.00

10.5 12.00 . 11.25 12.25 . 11.25 12.25 . 12.25 13.75 . 12.25 13.75 . 14.50 16.50 . 14.50 16.50 . 20.00 20.00 25.00 25.00 25.00 25.00

7.50 7.50 7.50 7.50 7.50 7.50

8.50 4.75 8.50 4.75 9.12 5.25

21.90 21.90 21.90 21.90 23.40 23.40

21.80 21.80 21.80 21.80 25.40 25.40

0.13 0.13 0.13 0.13 0.13 0.13

20.0 20.0 20.0 20.0 23.0 23.0

Dimensions in inches Dimensions are for reference only.

AB

U 1.625 +0.00 -0.001 1.875 +0.00 -0.001 1.625 +0.00 -0.001 2.125 +0.00 -0.001 1.875 +0.00 -0.001 2.375 +0.00 -0.001 1.875 +0.00 -0.001 2.875 +0.00 -0.001 2.125 +0.00 -0.001 3.375 +0.00 -0.001 2.375 +0.00 -0.001 3.375 2.375 3.375 2.375 3.625 2.625

143T 145T

XC 0.188 0.188

XD 0.188 0.188

XE 1.38 1.38

C 15.9 16.9

D 3.50 3.50

E 2.75 2.75

2F 4.00 5.00

BA 2.25 2.25

N-W 2.25 2.25

O 7.25 7.25

182T 184T

0.250 0.250

0.250 0.250

1.81 1.81

18.5 19.5

4.50 4.50

3.75 3.75

4.50 5.50

2.75 2.75

2.75 2.75

9.12 9.12

P 7.5 7.5

W 0.13 0.13

AB 6.7 6.7

9.3 9.3

0.13 0.13

8.0 8.0

U 0.875 +0.00 -0.0005 1.125 +0.00 -0.0005

Figure D Motor with Internally Mounted Encoder

404T 405T

XC 0.750 0.750

XD 0.750 0.750

XE 5.63 5.63

C 43.66 43.66

D 10 10

E 8 8

404TS 405TS

0.500 0.500

0.500 0.500

2.75 2.75

40.66 40.66

10 10

8 8

444T 445T

0.875 0.875

0.875 0.875

6.88 6.88

49.87 49.87

11 11

9 9

444TS 445TS

0.625 0.625

0.625 0.625

3.00 3.00

46.12 46.12

11 11

9 9

447T 447TS 449T 449TS S449LS S449SS

0.875 0.625 0.875 0.625 0.875 0.625

0.875 0.625 0.875 0.625 0.875 0.625

6.88 3.00 6.88 3.00 7.50 3.50

53.48 49.74 58.37 54.62 67.82 63.95

11 11 11 11 11 11

9 9 9 9 9 9

2F 12.25 13.75 . 12.25 13.75 . 14.50 16.50 . 14.50 16.50 . 20.00 20.00 25.00 25.00 25.00 25.00

BA 6.625 6.625

N-W 7.25 7.25

O 19.90 19.90

P 19.60 19.60

W 0.13 0.13

AB 18.4 18.4

6.625 6.625

4.25 4.25

19.90 19.90

19.60 19.60

0.13 0.13

18.4 18.4

7.500 7.500

8.50 8.50

21.90 21.90

21.70 21.70

0.13 0.13

19.6 19.6

7.500 7.500

4.75 4.75

21.90 21.90

21.70 21.70

0.13 0.13

19.6 19.6

7.500 7.500 7.500 7.500 7.500 7.500

8.50 4.75 8.50 4.75 9.12 5.25

21.90 21.90 21.90 21.90 23.40 23.40

21.80 21.80 21.80 21.80 25.40 25.40

0.13 0.13 0.13 0.13 0.13 0.13

19.6 19.6 19.6 19.6 23.0 23.0

U 2.875 +0.00 -0.001 2.125 +0.00 -0.001 3.375 +0.00 -0.001 2.375 +0.00 -0.001 3.375 2.375 3.375 2.375 3.625 2.625

Dimensions in inches Dimensions are for reference only.

8-26

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-27

Dimensions

XE

0.375 0.375

Typical Performance

XD

0.375 0.375

Modifications Accessories

Modifications Accessories

Lead Time

Lead Time

XC 254T 256T

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time Modifications Accessories

143T 145T

XC 0.188 0.188

XD 0.188 0.188

XE 1.38 1.38

C 15.2 16.3

D 3.50 3.50

E 2.75 2.75

2F 4.00 5.00

BA 2.25 2.25

N-W 2.25 2.25

O 6.93 6.93

P 7.7 7.7

W 0.13 0.13

AB 6.7 6.7

182T 184T

0.250 0.250

0.250 0.250

1.75 1.75

17.2 18.3

4.50 4.50

3.75 3.75

4.50 5.50

2.75 2.75

2.75 2.75

8.86 8.86

9.7 9.7

0.13 0.13

8.0 8.0

0.313 0.313

2.38 2.38

20.5 22.1

5.25 5.25

4.25 4.25

5.50 7.00

3.50 3.50

3.38 3.38

10.62 10.62

11.2 11.2

0.13 0.13

9.4 9.4

254T 256T

0.375 0.375

0.375 0.375

2.88 2.88

25.5 27.2

6.25 6.25

5.00 5.00

8.25 10.00

4.25 4.25

4.00 4.00

12.36 12.36

13.4 13.4

0.13 0.13

10.6 10.6

284T 286T

0.500 0.500

0.500 0.500

3.25 3.25

29.8 31.3

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

4.63 4.63

14.27 14.27

14.9 14.9

0.13 0.13

13.4 13.4

284TS 286TS

0.375 0.375

0.375 0.375

1.88 1.88

28.3 29.8

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

3.25 3.25

14.27 14.27

14.9 14.9

0.13 0.13

13.4 13.4

324T 326T

0.500 0.500

0.500 0.500

3.88 3.88

32.4 32.4

8.00 8.00

6.25 6.25

5.25 5.25

5.25 5.25

15.90 15.90

16.6 16.6

0.13 0.13

15.5 15.5

324TS 326TS

0.500 0.500

0.500 0.500

2.00 2.00

31.9 31.9

8.00 8.00

6.25 6.25

5.25 5.25

3.75 3.75

15.90 15.90

16.6 16.6

0.13 0.13

15.5 15.5

364T 365T

0.625 0.625

0.625 0.625

4.25 4.25

36.6 36.6

9.00 9.00

7.00 7.00

5.88 5.88

5.88 5.88

17.81 17.81

18.5 18.5

0.26 0.26

17.9 17.9

364TS 365TS

0.500 0.500

0.500 0.500

2.00 2.00

34.5 34.5

9.00 9.00

7.00 7.00

5.88 5.88

3.75 3.75

17.81 17.81

18.5 18.5

0.26 0.26

17.9 17.9

404T 405T

0.750 0.750

0.750 0.750

5.63 5.63

41.8 41.8

10.00 10.00

8.00 8.00

6.625 6.625

7.25 7.25

19.62 19.62

19.6 19.6

0.13 0.13

18.6 18.6

404TS 405TS

0.500 0.500

0.500 0.500

2.75 2.75

38.8 38.8

10.00 10.00

8.00 8.00

6.625 6.625

4.25 4.25

19.62 19.62

19.6 19.6

0.13 0.13

18.6 18.6

444T 445T

0.875 0.875

0.875 0.875

6.88 6.88

51.8 51.8

11.00 11.00

9.00 9.00

7.50 7.50

8.50 8.50

21.88 21.88

21.7 21.7

0.13 0.13

20.0 20.0

444TS 445TS

0.625 0.625

0.625 3 .00 0.625 3.00

48.0 48.0

11.00 11.00

9.00 9.00

7.50 7.50

4.75 4.75

21.88 21.88

21.7 21.7

0.13 0.13

20.0 20.0

447T 447TS 449T 449TS S449LS S449SS

0.875 0.625 0.875 0.625 0.875 0.625

0.875 0.625 0.875 0.625 0.875 0.625

51.4 47.7 56.5 52.6 69.4 65.5

11.00 11.00 11.00 11.00 11.00 11.00

9.00 9.00 9.00 9.00 9.00 9.00

10.50 12.00 . 10.50 12.00 . 11.25 12.25 . 11.25 12.25 . 12.25 13.75 . 12.25 13.75 . 14.50 16.50 . 14.50 16.50 . 20.00 20.00 25.00 25.00 25.00 25.00

7.50 7.50 7.50 7.50 7.50 7.50

8.50 4.75 8.50 4.75 9.12 5.25

21.88 21.88 21.88 21.88 23.40 23.40

21.8 21.8 21.8 21.8 25.4 25.4

0.13 0.13 0.13 0.13 0.13 0.13

20.0 20.0 20.0 20.0 23.0 23.0

6.88 3.00 6.88 3.00 7.5 0 3.50

XD

XE

C

D

E

BA

N-W

O

P

W

AB

U

0.313 0.313

0.313 0.313

2.38 2.38

22.2 23.7

5.25 5.25

4.25 4.25

2F 5.50 7.00

3.50 3.50

3.38 3.38

10.58 10.58

10.9 10.9

0.13 0.13

9.40 9.40

254T 256T

0.375 0.375

0.375 0.375

2.88 2.88

27.7 29.5

6.25 6.25

5.00 5.00

8.25 10.00

4.25 4.25

4.00 4.00

12.36 12.36

13.2 13.2

0.13 0.13

10.65 10.65

284T 286T

0.500 0.500

0.500 0.500

3.25 3.25

32.5 34.0

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

4.63 4.63

14.27 14.27

14.9 14.9

0.13 0.13

13.39 13.39

284TS 286TS

0.375 0.375

0.375 0.375

1.88 1.88

31.1 32.6

7.00 7.00

5.50 5.50

9.50 11.00

4.75 4.75

3.25 3.25

14.27 14.27

14.9 14.9

0.13 0.13

13.39 13.39

324T 326T

0.500 0.500

0.500 0.500

3.88 3.88

36.9 36.9

8.00 8.00

6.25 6.25

10.5 12.00

5.25 5.25

5.25 5.25

15.94 15.94

16.6 16.6

0.13 0.13

15.50 15.50

324TS 326TS

0.500 0.500

0.500 0.500

2.00 2.00

35.4 35.4

8.00 8.00

6.25 6.25

10.5 12.00

5.25 5.25

3.75 3.75

15.90 15.90

16.6 16.6

0.13 0.13

15.50 15.50

364T 365T

0.625 0.625

0.625 0.625

4.25 4.25

39.4 39.4

9.00 9.00

7.00 7.00

11.25 12.25

5.88 5.88

5.88 5.88

17.81 17.81

18.4 18.4

0.38 0.38

17.94 17.94

364TS 365TS

0.500 0.500

0.500 0.500

2.00 2.00

37.3 37.3

9.00 9.00

7.00 7.00

11.25 12.25

5.88 5.88

3.75 3.75

17.81 17.81

18.4 18.4

0.38 0.38

17.94 17.94

1.375 +0.00 -0.0005 1.625 +0.00 -0.001 1.875 +0.00 -0.001 1.625 +0.00 -0.001 2.125 +0.00 -0.001 1.875 +0.00 -0.001 2.375 +0.00 -0.001 1.875 +0.00 -0.001

Dimensions in inches Dimensions are for reference only.

Dimensions in inches Dimensions are for reference only.

8-28

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

8-29

Dimensions

0.313 0.313

XC 213T 215T

Typical Performance

213T 215T

U 0.875 +0.00 -0.0005 1.125 +0.00 -0.0005 1.375 +0.00 -0.0005 1.625 +0.00 -0.001 1.875 +0.00 -0.001 1.625 +0.00 -0.001 2.125 +0.00 -0.001 1.875 +0.00 -0.001 2.375 +0.00 -0.001 1.875 +0.00 -0.001 2.875 +0.00 -0.001 2.125 +0.00 -0.001 3.375 +0.00 -0.001 2.375 +0.00 -0.001 3.375 2.375 3.375 2.375 3.625 2.625

Modifications Accessories

Typical Performance

RGZESDI Figure F Motor with Externally Mounted Lake Shore 8500 Encoder

Lead Time

Dimensions

RGZESDI Figure E Motor with Dynapar HS35 Encoder

INVERTER Duty Hazardous Duty

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty

Severe Duty - TEFC Motors

INVERTER Duty Severe Duty INVERTER Duty Hazardous Duty Lead Time Modifications Accessories

Narrow V1 Min. Dia. 8.4

60

1800

364T

7.4

7.4

60

1200

404T

8

9

60

900

405T

10

10

75

1800

365T

75

1200

405T

8.6 10

Std. V2 Min. Dia. 9

Notes

9 10

900

444T

9.5

13

1800

405T

8.6

10

100

1200

444T

10

11.8

100

900

445T

12

15

125

1800

444T

10.5

12

125

1200

445T

12.4

15.2

125

900

447T

14

18.5

150

1800

445T

10.5

13.2

150

1200

447T

11.6

16.1

15

900

447T

14.6

24.7

200

1800

447T

13.2

15.8

200

1200

449T

14.6

25

200

900

449T

18

-

250

1800

449T

13

18.4

250

1200

449T

18.2

-

250

900

S449LS

19.8

-

300

1800

449T

15.4

24.8

300

1200

S449LS

18.4

-

350

1800

S449LS

15.8

-

350

1200

S449LS

21

-

400

1800

S449LS

18

-

Typical Performance

75 100

Modifications Accessories

Typical Performance

Frame 404T

Lead Time

Notes: 1. Example: 3V, 5V, 8V. Sheave face cannot overhand end of shaft. 2. Example: A, B, C, D section. Center of sheave width cannot overhang end of shaft. 3. Do not exceed belt service factor of 1.6. Follow manufacturer’s instructions for alignment and belt tensioning. Position sheaves as close to the drive end bearing as possible. (Maximum 1/2”” from shaft shoulder). 4. Maximum speed reduction of 5:1. 5. Shaft center distance approximately equal to diameter of largest sheave. 6. All dimensions in inches.

8-30

2007 Low Voltage AC Motors Selection and Pricing Guide

Dimensions

Dimensions

RPM 900

INVERTER Duty Hazardous Duty

HP 50

INVERTER Duty Severe Duty

RECOMMENDED SHEAVE DIAMETERS - TEFC MOTORS

2007 Low Voltage AC Motors Selection and Pricing Guide

8-31

Siemens IEC Motors Features at a Glance Improved Efficiency

Electrical Data

1LA7 See Page 10-8

High Efficiency 1LA6 See Page 10-17

1MJ See Page 10-19

1LA9 See Page 10-1

1LG6 See Page 10-5

Enclosure

TEFC

TEFC

TEFC

TEFC

TEFC

Efficiency

eff2

eff2

eff2

eff1

eff1

Power Range

60Hz: 0.07 - 21.3 kW

60Hz: 0.86 - 21.3 kW

60Hz: 0.10 - 152 kW

60Hz: 1/6 - 25 HP

60Hz: 25-300 HP

50Hz: 0.12 - 18.5 kW

50Hz: 0.75 - 18.5

50Hz: 0.37 - 132 kW

50Hz: 0.16 - 18.5 kW

50Hz: 18.5 - 250kW

Frame Size

56 -160

100-160

71-315

56-160

180-315

Frequency

50 and 60 Hertz

50 Hertz

50 Hertz

50 and 60 Hertz

50 and 60 Hertz

Power

3 - Phase

3 - Phase

3 - Phase

3 - Phase

3 - Phase

Voltage

230/400 @ 50 Hertz, 460V @ 60 Hertz

230/400

230/400

230/400 @ 50 Hertz, 460V @ 60 Hertz

230/400 @ 50 Hertz, 460V @ 60 Hertz

Service Factor (sine wave)

Stock 1.1

1.0

1.0

Stock 1.15

Stock 1.15

Electrical Design

Design N

Design N

Design N

Design N

Design N

Stator Windings

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Copper - Random Wound

Insulation

Class F

Class F

Class F

Class F

Class F

Temperature Rise

Class B @ 1.0SF, Class F @ 1.1SF

Class B @ 1.0SF, Class F @ 1.1SF

Class B @ 1.0SF

Class B @ 1.0SF, Class F @ 1.15SF

Class B @ 1.0SF, Class F @ 1.15SF

Warranty

12/18 month

12/18 month

12/18 month

12/18 month

12/18 month

Frame

Cast Aluminum

Cast Iron

Cast Iron

Cast Aluminum

Cast Iron

Endshields

Cast Aluminum

Cast Iron

Cast Iron

Cast Aluminum

Cast Iron

Conduit Box

Aluminum Alloy

Cast Iron

71-132, 180-225 Aluminum Alloy

Aluminum

180-225, Aluminum Alloy

Mechanical Data

160, 250-315, Cast Iron

9-1

250-315, Cast Iron

Lead Seal Gasket

Neoprene

Neoprene

Neoprene

Fan Cover

Corrosion Protected Steel Plate

Corrosion Protected Steel Plate

Corrosion Protected Steel Plate

Cooling Fan

Plastic

Plastic

Plastic

Plastic

Plastic

Rotor

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Die Cast Aluminum

Bearing Type

Double Shielded

Double Shielded

71-80: Single Shielded 90-250: Shielded

Neoprene

Neoprene

Corrosion Protected Steel Plate

Glass Reinforced Plastic

180-250: Single Shielded Double Shielded

280-315: Regreasable

IP55

280-315: Regreasable Protection Design

IP55

IP55

IP55

IP55

Lubrication

Lithium

Lithium

Lithium

Lithium

Lithium

Lube Inlet Fittings

Sealed Bearings

Sealed Bearings

Up To 250: Sealed Bearings

Sealed Bearings

Up To 250: Sealed Bearings

280 and above: Flat Type Nipple

280 and above: Flat Type Nipple

Condensation Drain

Optional

Optional

Not Permitted

Optional

Standard

Hardware

Zinc Plated

Zinc Plated

Zinc Plated

Zinc Plated

Zinc Plated

Lifting Eyebolt

30 kg and above

30 kg and above

30 kg and above

30 kg and above

30 kg and above

Nameplate

Stainless Steel

Stainless Steel

Stainless Steel

Stainless Steel

Stainless Steel

Paint

RAL 7030 “World wide finish”

RAL 7030 “World wide finish”

RAL 7030 “World wide finish”

RAL 7030 “World wide finish”

RAL 7030 Standard Finish

Vibration

Severity Grade A

Severity Grade A

Severity Grade A

Severity Grade A

Severity Grade A

Up to 132

1.6 mm/s

1.6 mm/s

1.6 mm/s

1.6 mm/s

1.6 mm/s

160-225

2.2 mm/s

2.2 mm/s

2.2 mm/s

2.2 mm/s

2.2 mm/s

250-350

2.8 mm/s

2.8 mm/s

2.8 mm/s

2.8 mm/s

2.8 mm/s

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

9-2

General Purpose - TEFC IEC Motor 1LA7 - Aluminum Frame

Frame & End Shields - Cast aluminum construction for exceptional heat dissipation and structural integrity. All motors are designed with degree of protection IP55 (IEC 529), suitable for use in dusty or damp surroundings, ready for their use in the tropics. (IP56 and IP65 available)

Cooling - Motors are fitted with a radialflow fan which functions independently of the direction of rotation (cooling method IC 411 to DIN EN 60034-6). The material of the external cooling fans is reinforced plastic. This material is tested and certified for a 20 year lifetime. Fan cowls are made of corrosion protected steel plate. Bearings - The bearing nominal life is specified by standard calculation (DIN ISO 281) and is achieved or exceeds by 90% if used according to instructions, if the operating conditions are below average a bearing life of 100,000 (Lh10 hours) can be achieved.

Lubrication - The grease life, for prelubricated motors, is tailored to the bearing life. In those cases where relubrication is chosen, the motors are provided with a grease retaining system that prevents grease from entering the motor. Siemens IEC motors use a lithium based grease. Conduit Box - Cast aluminumconstruction, top mounted as standard, the terminal box can be ordered to either side of the motor and be rotated 90º or 180º (frames size 80 and above) providing a more flexible mounting. In addition to the standard terminal box earthing, an external earthing is also made available for all motors upon request. Corrosion Resistance - Zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. (Stainless steel hardware also available) Flexible - All Siemens IEC motors are available with a wide variety of options to meet your specific motor needs.

Specifications table begins on the next page

9-3

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

10-1

IEC MOTORS EFF1 C.I. Frame

Features for Long Life

Insulation - DURIGNIT® IR 2000, inverter-compatible up to 500 V, optionally up to 690 V. This insulation system comprised of high-grade enameled wires and insulating sheet materials combine with solvent-freeimpregnating resin. The system ensures a high level of mechanical and electrical strength as well as good serviceability and long motor life. The insulation offers general protection for the windings against corrosive gases, vapors, dust, oil and increased humidity, and resists the normal stresses of vibration.

IEC MOTORS EFF1 Alum. Frame

• 90W to 18.5kW • Overload reserve in continuous mode (SF 1.1) • Dual Frequency rated • 3000, 1500, 1000, 750 RPM 3600, 1800, 1200, 900 RPM • 3 phase, 50 Hz; 230VD/400VY and 60 Hz; 460VY • 3 phase, 50 Hz; 400VD/690VY and 60 Hz; 460VD • All commonly used voltages (50Hz and 60Hz) available • EU/CEMEP efficiency classification EFF2 (Improved efficiency) • Class F insulation, Class B temperature rise • Continuous Duty, Suitable for Converted fed operation • CE Marked, IEC 60034 • NEMA MG1-12 compatibility available • UL and CSA label marks available • 56 through 160 frame

Stator/Windings - Manufactured with premium electrical grade steel laminations and the finest copper electrical magnet wire for lower losses and improved efficiencies. A unique stator core design lowers flux density and increases cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

IEC MOTORS Explosion Proof

Performance Specifications

Rotor - A unique offset laminated rotor core design provides improved efficiency while larger bars and Aluminum end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced (IEC 60034-14) for extended bearing life.

IEC MOTORS EFF2 C.I. Frame

The 1LA7 motors, with their wide variety of options, fit in every drive system concept and cover more than 90% of all imaginable applications worldwide, suitable for indoor and outdoor applications where light weight and excellent price/performance ratio and high degree of operational reliability are required. This powerful energy-saving motor is less harmful to the environment thanks to reduction in CO2 emission.

Improved Efficiency (eff2)

IEC MOTORS EFF2 Alum. Frame

Notes

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame

1LA7 Aluminum Frame

1LA7 Aluminum Frame

kW kW 50Hz 60Hz 0.06 0.07

RPM 50Hz Frame 1500 56M

0.09

0.1

3000

56M

1LA7

0.09

0.1

0.09

0.1

1500

56M

1000

63M

0.09

0.1

750

0.12

0.14

0.12

0.14

0.12

Type 1LA7

Part Number 1LA7 113-2AA60

List Price $ 686

Frame 112M

4.6

1500

112M

1LA7

BALL

1LA7 113-4AA60

717

CA-EF10

4

4.6

4

4.6

1000

132M

1LA7

BALL

1LA7 133-6AA60

1030

CA-EF10

750

160M

1LA7

BALL

1LA7 163-8AB60

1570

CA-EF10

10

6

5.5

6.3

3000

132S

1LA7

BALL

1LA7 130-2AA60

884

CA-EF10

10.4

86.5%

65.0%

3

39

5.5

6.3

1500

132S

1LA7

BALL

1LA7 130-4AA60

915

CA-EF10

11.4

86.0%

41

55.0%

4

5.5

6.3

1000

132M

1LA7

BALL

1LA7 134-6AA60

1300

CA-EF10

12.6

83.0%

52

6

5.5

6.3

750

160M

1LA7

BALL

1LA7 164-8AB60

1960

CA-EF10

13

83.5%

74

8.6

3000

132S

1LA7

BALL

1LA7 131-2AA60

1140

CA-EF10

13.8

88.0%

48 49

Part Number 1LA7 050-4AB10

Amps 50Hz 0.2

BALL

1LA7 050-2AA10

174

CA-EF10

0.26

63.0%

3

4

1LA7

BALL

1LA7 053-4AB10

175

CA-EF10

0.29

58.0%

3

1LA7

BALL

1LA7 063-6AB10

193

CA-EF10

0.44

45.0%

4

71M

1LA7

BALL

1LA7 070-8AB10

222

CA-EF10

0.36

53.0%

3000

56M

1LA7

BALL

1LA7 053-2AA10

175

CA-EF10

0.32

1500

63M

1LA7

BALL

1LA7 060-4AB10

179

SA-EF20

0.42

1000

71M

1LA7

BALL

1LA7 073-8AB10

250

CA-EF10

0.51

53.0%

✔

Multiplier Symbol CA-EF10

Amps 50Hz 7.8

FL FL Nom. Eff. Weight 50Hz (kg) 86.0% 29

DE Bearing BALL

Multiplier Symbol CA-EF20

8.2

85.0%

31

9.4

80.5%

44

80.0%

64

0.18

0.21

3000

63M

1LA7

BALL

1LA7 060-2AA10

181

SA-EF20

0.5

63.0%

4

✔

0.18

0.21

1500

63M

1LA7

BALL

1LA7 063-4AB10

192

SA-EF20

0.56

60.0%

4

✔

7.5

8.6

1500

132M

1LA7

BALL

1LA7 133-4AA60

1170

CA-EF10

15.2

87.0%

✔

7.5

8.6

1000

160M

1LA7

BALL

1LA7 163-6AA60

1690

CA-EF10

17

86.0%

74

7.5

8.6

750

160L

1LA7

BALL

1LA7 166-8AB60

2420

CA-EF10

17.6

85.5%

94

11

12.6

3000

160M

1LA7

BALL

1LA7 163-2AA60

1570

CA-EF10

20

89.5%

68

11

12.6

1500

160M

1LA7

BALL

1LA7 163-4AA60

1610

CA-EF10

21.5

88.5%

73

1LA7

BALL

1LA7 166-6AA60

2340

CA-EF10

24.5

87.5%

95

0.21

1000

71M

1LA7

BALL

1LA7 070-6AA10

210

SA-EF20

0.67

53.0%

5

0.18

0.21

750

80M

1LA7

BALL

1LA7 080-8AB10

266

CA-EF10

0.75

51.0%

9

0.25

0.29

3000

63M

1LA7

BALL

1LA7 063-2AA10

192

CA-EF10

0.68

65.0%

4

0.25

0.29

1500

71M

1LA7

BALL

1LA7 070-4AB10

197

SA-EF20

0.77

60.0%

5

✔

0.25

0.29

1000

71M

1LA7

BALL

1LA7 073-6AA10

235

SA-EF20

0.79

60.0%

6

✔

11

12.6

1000

160L

0.25

0.29

750

80M

1LA7

BALL

1LA7 083-8AB10

328

CA-EF10

1.02

55.0%

10

15

17.3

3000

160M

1LA7

BALL

1LA7 164-2AA60

2060

CA-EF10

26.5

90.0%

77

0.37

0.43

3000

71M

1LA7

BALL

1LA7 070-2AA10

200

SA-EF20

1

66.0%

5

✔

15

17.3

1500

160L

1LA7

BALL

1LA7 166-4AA60

2090

CA-EF10

28.5

90.0%

85

0.37

0.43

1500

71M

1LA7

BALL

1LA7 073-4AB10

221

CA-EF10

1.06

65.0%

6

18.5

21.3

3000

160L

1LA7

BALL

1LA7 166-2AA60

2460

CA-EF10

32

91.0%

86

0.37

0.43

1000

80M

1LA7

BALL

1LA7 080-6AA10

259

SA-EF20

1.2

62.0%

9

0.37

0.43

750

90S

1LA7

BALL

1LA7 090-8AB10

403

CA-EF10

1.14

63.0%

11

0.63

3000

71M

1LA7

BALL

1LA7 073-2AA10

226

CA-EF10

1.36

71.0%

6

0.63

1500

80M

1LA7

BALL

1LA7 080-4AA10

249

CA-EF10

1.46

67.0%

9

0.55

0.63

1000

80M

1LA7

BALL

1LA7 083-6AA10

300

CA-EF10

1.6

67.0%

10

0.55

0.63

750

90L

1LA7

BALL

1LA7 096-8AB10

490

CA-EF10

1.58

66.0%

13

0.75

0.86

3000

80M

1LA7

BALL

1LA7 080-2AA10

259

CA-EF10

1.73

73.0%

9

0.75

0.86

1500

80M

1LA7

BALL

1LA7 083-4AA10

270

CA-EF10

1.91

72.0%

10 13

0.75

0.86

1000

90S

1LA7

BALL

1LA7 090-6AA10

354

CA-EF10

2.05

69.0%

0.75

0.86

750

100L

1LA7

BALL

1LA7 106-8AB10

542

CA-EF10

2.15

66.0%

19

1.1

1.3

3000

80M

1LA7

BALL

1LA7 083-2AA10

297

CA-EF10

2.4

77.0%

11

1.1

1.3

1500

90S

1LA7

BALL

1LA7 090-4AA10

335

CA-EF10

2.55

77.0%

13

1.1

1.3

1000

90L

1LA7

BALL

1LA7 096-6AA10

438

CA-EF10

2.85

72.0%

16

1.1

1.3

750

100L

1LA7

BALL

1LA7 107-8AB10

686

CA-EF10

2.9

72.0%

22

1.5

1.75

3000

90S

1LA7

BALL

1LA7 090-2AA10

358

CA-EF10

3.25

79.0%

13

1.5

1.75

1500

90L

1LA7

BALL

1LA7 096-4AA10

398

CA-EF10

3.40

79.0%

16

1.5

1.75

1000

100L

1LA7

BALL

1LA7 106-6AA10

521

CA-EF10

3.9

74.0%

21

1.5

1.75

750

112M

1LA7

BALL

1LA7 113-8AB60

815

CA-EF10

3.85

74.0%

24

2.2

2.55

3000

90L

1LA7

BALL

1LA7 096-2AA10

461

CA-EF10

4.55

82.0%

16

2.2

2.55

1500

100L

1LA7

BALL

1LA7 106-4AA10

490

CA-EF10

4.7

82.0%

21

2.2

2.55

1000

112M

1LA7

BALL

1LA7 113-6AA60

653

CA-EF10

5.2

78.0%

26

2.2

2.55

750

132S

1LA7

BALL

1LA7 130-8AB60

1050

CA-EF10

5.7

75.0%

38

3

3.45

3000

100L

1LA7

BALL

1LA7 106-2AA10

557

CA-EF10

6.1

84.0%

22

3

3.45

1500

100L

1LA7

BALL

1LA7 107-4AA10

564

CA-EF10

6.4

83.0%

24

3

3.45

1000

132S

1LA7

BALL

1LA7 130-6AA60

825

CA-EF10

7.2

79.0%

38

3

3.45

750

132M

1LA7

BALL

1LA7 133-8AB60

1280

CA-EF10

7.6

77.0%

44

10-2

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

IEC MOTORS EFF1 C.I. Frame

0.55 0.55

Stock Model

IEC MOTORS EFF1 Alum. Frame

IEC MOTORS EFF1 Alum. Frame

RPM 50Hz 3000

Stock Model

kW kW 50Hz 60Hz 4 4.6

List Price $ 174

7.5

0.18

IEC MOTORS EFF1 C.I. Frame

0.14

FL FL Nom. Eff. Weight 50Hz (kg) 56.0% 3

Horizontal, Foot Mounted

IEC MOTORS Explosion Proof

Type 1LA7

DE Bearing BALL

Horizontal, Foot Mounted

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS Explosion Proof

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

2007 Low Voltage AC Motors Selection and Pricing Guide

10-3

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

1LA7 Aluminum Frame

1LA7 Aluminum Frame

IEC MOTORS Explosion Proof

Frame 56M

0.09

3000

56M

0.1

Type 1LA7

Part Number 1LA7 050-4AB10-Z A11

1LA7

BALL

1LA7 050-2AA10-Z A11

242

CA-EF10

0.26

63.0%

Stock Model

kW kW 50Hz 60Hz 4 4.6

RPM 3000

Frame 112M

Type 1LA7

DE Bearing BALL

Part Number 1LA7 113-2AA60-Z A11

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 777 CA-EF10 7.8 86.0% 29

3

4

4.6

1500

112M

1LA7

BALL

1LA7 113-4AA60-Z A11

808

CA-EF10

8.2

85.0%

31

4

4.6

1000

132M

1LA7

BALL

1LA7 133-6AA60-Z A11

1132

CA-EF10

9.4

80.5%

44 64

0.09

0.1

1500

56M

1LA7

BALL

1LA7 053-4AB10-Z A11

243

CA-EF10

0.29

58.0%

3

0.09

0.1

1000

63M

1LA7

BALL

1LA7 063-6AB10-Z A11

261

CA-EF10

0.44

45.0%

4

4

4.6

750

160M

1LA7

BALL

1LA7 163-8AB60-Z A11

1672

CA-EF10

10

80.0%

0.09

0.1

750

71M

1LA7

BALL

1LA7 070-8AB10-Z A11

290

CA-EF10

0.36

53.0%

6

5.5

6.3

3000

132S

1LA7

BALL

1LA7 130-2AA60-Z A11

986

CA-EF10

10.4

86.5%

39

0.12 0.14

3000

56M

1LA7

BALL

1LA7 053-2AA10-Z A11

243

CA-EF10

0.32

65.0%

3

5.5

6.3

1500

132S

1LA7

BALL

1LA7 130-4AA60-Z A11

1017

CA-EF10

11.4

86.0%

41

0.12 0.14

1500

63M

1LA7

BALL

1LA7 060-4AB10-Z A11

247

SA-EF20

0.42

55.0%

4

5.5

6.3

1000

132M

1LA7

BALL

1LA7 134-6AA60-Z A11

1402

CA-EF10

12.6

83.0%

52

0.12 0.14

750

71M

1LA7

BALL

1LA7 073-8AB10-Z A11

318

CA-EF10

0.51

53.0%

6

5.5

6.3

750

160M

1LA7

BALL

1LA7 164-8AB60-Z A11

2062

CA-EF10

13

83.5%

74

0.18 0.21

3000

63M

1LA7

BALL

1LA7 060-2AA10-Z A11

249

SA-EF20

0.5

63.0%

4

7.5

8.6

3000

132S

1LA7

BALL

1LA7 131-2AA60-Z A11

1242

CA-EF10

13.8

88.0%

48

0.18 0.21

1500

63M

1LA7

BALL

1LA7 063-4AB10-Z A11

260

SA-EF20

0.56

60.0%

4

7.5

8.6

1500

132M

1LA7

BALL

1LA7 133-4AA60-Z A11

1272

CA-EF10

15.2

87.0%

49

0.18 0.21

1000

71M

1LA7

BALL

1LA7 070-6AA10-Z A11

278

SA-EF20

0.67

53.0%

5

7.5

8.6

1000

160M

1LA7

BALL

1LA7 163-6AA60-Z A11

1792

CA-EF10

17

86.0%

74

0.18 0.21

750

80M

1LA7

BALL

1LA7 080-8AB10-Z A11

345

CA-EF10

0.75

51.0%

9

7.5

8.6

750

160L

1LA7

BALL

1LA7 166-8AB60-Z A11

2522

CA-EF10

17.6

85.5%

94

11

12.6

3000

160M

1LA7

BALL

1LA7 163-2AA60-Z A11

1672

CA-EF10

20

89.5%

68

11

12.6

1500

160M

1LA7

BALL

1LA7 163-4AA60-Z A11

1712

CA-EF10

21.5

88.5%

73

6

11

12.6

1000

160L

1LA7

BALL

1LA7 166-6AA60-Z A11

2442

CA-EF10

24.5

87.5%

95

55.0%

10

15

17.3

3000

160M

1LA7

BALL

1LA7 164-2AA60-Z A11

2162

CA-EF10

26.5

90.0%

77

0.25 0.29

3000

63M

1LA7

BALL

1LA7 063-2AA10-Z A11

260

CA-EF10

0.68

65.0%

4

0.25 0.29

1500

71M

1LA7

BALL

1LA7 070-4AB10-Z A11

265

SA-EF20

0.77

60.0%

5

0.25 0.29

1000

71M

1LA7

BALL

1LA7 073-6AA10-Z A11

303

SA-EF20

0.79

60.0%

0.25 0.29

750

80M

1LA7

BALL

1LA7 083-8AB10-Z A11

407

CA-EF10

1.02

3000

71M

1LA7

BALL

1LA7 070-2AA10-Z A11

268

SA-EF20

1

66.0%

5

1500

71M

1LA7

BALL

1LA7 073-4AB10-Z A11

289

CA-EF10

1.06

65.0%

6

0.37 0.43

1000

80M

1LA7

BALL

1LA7 080-6AA10-Z A11

338

SA-EF20

1.2

62.0%

9

0.37 0.43

750

90S

1LA7

BALL

1LA7 090-8AB10-Z A11

482

CA-EF10

1.14

63.0%

11

0.55 0.63

3000

71M

1LA7

BALL

1LA7 073-2AA10-Z A11

294

CA-EF10

1.36

71.0%

6

0.55 0.63

1500

80M

1LA7

BALL

1LA7 080-4AA10-Z A11

328

CA-EF10

1.46

67.0%

9

0.55 0.63

1000

80M

1LA7

BALL

1LA7 083-6AA10-Z A11

379

CA-EF10

1.6

67.0%

10 13

0.55 0.63

750

90L

1LA7

BALL

1LA7 096-8AB10-Z A11

569

CA-EF10

1.58

66.0%

0.75 0.86

3000

80M

1LA7

BALL

1LA7 080-2AA10-Z A11

338

CA-EF10

1.73

73.0%

9

0.75 0.86

1500

80M

1LA7

BALL

1LA7 083-4AA10-Z A11

349

CA-EF10

1.91

72.0%

10

0.75 0.86

1000

90S

1LA7

BALL

1LA7 090-6AA10-Z A11

433

CA-EF10

2.05

69.0%

13

0.75 0.86

750

100L

1LA7

BALL

1LA7 106-8AB10-Z A11

633

CA-EF10

2.15

66.0%

19

1LA7

BALL

1LA7 083-2AA10-Z A11

376

CA-EF10

2.4

77.0%

11

1.1

1.3

3000

80M

1.1

1.3

1500

90S

1LA7

BALL

1LA7 090-4AA10-Z A11

414

CA-EF10

2.55

77.0%

13

1.1

1.3

1000

90L

1LA7

BALL

1LA7 096-6AA10-Z A11

517

CA-EF10

2.85

72.0%

16

1.1

22

1.3

750

100L

1LA7

BALL

1LA7 107-8AB10-Z A11

777

CA-EF10

2.9

72.0%

1.5 1.75

3000

90S

1LA7

BALL

1LA7 090-2AA10-Z A11

437

CA-EF10

3.25

79.0%

13

1.5 1.75

1500

90L

1LA7

BALL

1LA7 096-4AA10-Z A11

477

CA-EF10

3.4

79.0%

16

1.5 1.75

1000

100L

1LA7

BALL

1LA7 106-6AA10-Z A11

612

CA-EF10

3.9

74.0%

21

1.5 1.75

750

112M

1LA7

BALL

1LA7 113-8AB60-Z A11

906

CA-EF10

3.85

74.0%

24

2.2 2.55

3000

90L

1LA7

BALL

1LA7 096-2AA10-Z A11

540

CA-EF10

4.55

82.0%

16

2.2 2.55

1500

100L

1LA7

BALL

1LA7 106-4AA10-Z A11

581

CA-EF10

4.7

82.0%

21

2.2 2.55

1000

112M

1LA7

BALL

1LA7 113-6AA60-Z A11

744

CA-EF10

5.2

78.0%

26

2.2 2.55

750

132S

1LA7

BALL

1LA7 130-8AB60-Z A11

1152

CA-EF10

5.7

75.0%

38

3 3.45

3000

100L

1LA7

BALL

1LA7 106-2AA10-Z A11

648

CA-EF10

6.1

84.0%

22

3 3.45

1500

100L

1LA7

BALL

1LA7 107-4AA10-Z A11

655

CA-EF10

6.4

83.0%

24

3 3.45

1000

132S

1LA7

BALL

1LA7 130-6AA60-Z A11

927

CA-EF10

7.2

79.0%

38

3 3.45

750

132M

1LA7

BALL

1LA7 133-8AB60-Z A11

1382

CA-EF10

7.6

77.0%

44

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

✔

15

17.3

1500

160L

1LA7

BALL

1LA7 166-4AA60-Z A11

2192

CA-EF10

28.5

90.0%

85

18.5

21.3

3000

160L

1LA7

BALL

1LA7 166-2AA60-Z A11

2562

CA-EF10

32

91.0%

86

IEC MOTORS EFF1 C.I. Frame

0.37 0.43 0.37 0.43

10-4

✔

Stock Model

IEC MOTORS EFF1 Alum. Frame

IEC MOTORS EFF1 Alum. Frame

RPM 1500

DE Bearing BALL

Horizontal, Foot Mounted, with Thermistors

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 C.I. Frame

kW kW 50Hz 60Hz 0.06 0.07

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 242 CA-EF10 0.2 56.0% 3

✔

✔

✔

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF2 C.I. Frame

Horizontal, Foot Mounted, with Thermistors

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

10-5

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame IEC MOTORS Explosion Proof

RPM 1500

Frame 56M

0.09

0.1

3000

0.09

0.1

0.09

0.1

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 207 CA-EF10 0.2 56.0% 3

Stock Model

1LA7 Aluminum Frame

B5 Flange, Footless FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 762 CA-EF10 7.8 86.0% 29

Type 1LA7

DE Bearing BALL

Part Number 1LA7 050-4AB11

56M

1LA7

BALL

1LA7 050-2AA11

207

CA-EF10

0.26

63.0%

3

4

4.6

1500

112M

1LA7

BALL

1LA7 113-4AA11

793

CA-EF10

8.2

85.0%

31

1500

56M

1LA7

BALL

1LA7 053-4AB11

208

CA-EF10

0.29

58.0%

3

4

4.6

1000

132M

1LA7

BALL

1LA7 133-6AA11

1129

CA-EF10

9.4

80.5%

44

1000

63M

1LA7

BALL

1LA7 063-6AB11

226

CA-EF10

0.44

45.0%

4

4

4.6

750

160M

1LA7

BALL

1LA7 163-8AB11

1698

CA-EF10

80.0%

64

kW kW 50Hz 60Hz 4 4.6

RPM Frame 3000 112M

Type 1LA7

DE Bearing BALL

Part Number 1LA7 113-2AA11

10

Stock Model

✔

0.09

0.1

750

71M

1LA7

BALL

1LA7 070-8AB11

258

CA-EF10

0.36

53.0%

6

5.5

6.3

3000

132S

1LA7

BALL

1LA7 130-2AA11

983

CA-EF10

10.4

86.5%

39

0.12

0.14

3000

56M

1LA7

BALL

1LA7 053-2AA11

208

CA-EF10

0.32

65.0%

3

5.5

6.3

1500

132S

1LA7

BALL

1LA7 130-4AA11

1014

CA-EF10

11.4

86.0%

41

0.12

0.14

1500

63M

1LA7

BALL

1LA7 060-4AB11

212

SA-EF20

0.42

55.0%

4

5.5

6.3

1000

132M

1LA7

BALL

1LA7 134-6AA11

1399

CA-EF10

12.6

83.0%

52

0.12

0.14

750

71M

1LA7

BALL

1LA7 073-8AB11

286

CA-EF10

0.51

53.0%

6

5.5

6.3

750

160M

1LA7

BALL

1LA7 164-8AB11

2088

CA-EF10

13

83.5%

74

0.18

0.21

3000

63M

1LA7

BALL

1LA7 060-2AA11

214

SA-EF20

0.5

63.0%

4

✔

7.5

8.6

3000

132S

1LA7

BALL

1LA7 131-2AA11

1239

CA-EF10

13.8

88.0%

48

0.18

0.21

1500

63M

1LA7

BALL

1LA7 063-4AB11

225

SA-EF20

0.56

60.0%

4

✔

7.5

8.6

1500

132M

1LA7

BALL

1LA7 133-4AA11

1269

CA-EF10

15.2

87.0%

49

0.18

0.21

1000

71M

1LA7

BALL

1LA7 070-6AA11

246

SA-EF20

0.67

53.0%

5

7.5

8.6

1000

160M

1LA7

BALL

1LA7 163-6AA11

1818

SA-EF10

17

86.0%

74

0.18

0.21

750

80M

1LA7

BALL

1LA7 080-8AB11

307

CA-EF10

0.75

51.0%

9

7.5

8.6

750

160L

1LA7

BALL

1LA7 166-8AB11

2548

CA-EF10

17.6

85.5%

94

0.25

0.29

3000

63M

1LA7

BALL

1LA7 063-2AA11

225

CA-EF10

0.68

65.0%

4

✔

11

12.6

3000

160M

1LA7

BALL

1LA7 163-2AA11

1698

CA-EF10

20

89.5%

68

0.25

0.29

1500

71M

1LA7

BALL

1LA7 070-4AB11

233

SA-EF20

0.77

60.0%

5

✔

11

12.6

1500

160M

1LA7

BALL

1LA7 163-4AA11

1738

CA-EF10

21.5

88.5%

73

0.25

0.29

1000

71M

1LA7

BALL

1LA7 073-6AA11

271

SA-EF20

0.79

60.0%

6

✔

11

12.6

1000

160L

1LA7

BALL

1LA7 166-6AA11

2468

CA-EF10

24.5

87.5%

95

✔

0.25

0.29

750

80M

1LA7

BALL

1LA7 083-8AB11

369

CA-EF10

1.02

55.0%

10

15

17.3

3000

160M

1LA7

BALL

1LA7 164-2AA11

2188

CA-EF10

26.5

90.0%

77

✔

0.37

0.43

3000

71M

1LA7

BALL

1LA7 070-2AA11

236

SA-EF20

1

66.0%

5

15

17.3

1500

160L

1LA7

BALL

1LA7 166-4AA11

2218

CA-EF10

28.5

90.0%

85

0.37

0.43

1500

71M

1LA7

BALL

1LA7 073-4AB11

257

CA-EF10

1.06

65.0%

6

18.5

21.3

3000

160L

1LA7

BALL

1LA7 166-2AA11

2588

CA-EF10

32

91.0%

86

0.37

0.43

1000

80M

1LA7

BALL

1LA7 080-6AA11

300

SA-EF20

1.2

62.0%

9

0.37

0.43

750

90S

1LA7

BALL

1LA7 090-8AB11

453

CA-EF10

1.14

63.0%

11

0.55

0.63

3000

71M

1LA7

BALL

1LA7 073-2AA11

262

CA-EF10

1.36

71.0%

6

0.55

0.63

1500

80M

1LA7

BALL

1LA7 080-4AA11

290

CA-EF10

1.46

67.0%

9

0.55

0.63

1000

80M

1LA7

BALL

1LA7 083-6AA11

341

CA-EF10

1.6

67.0%

10

0.55

0.63

750

90L

1LA7

BALL

1LA7 096-8AB11

540

CA-EF10

1.58

66.0%

13

0.75

0.86

3000

80M

1LA7

BALL

1LA7 080-2AA11

300

CA-EF10

1.73

73.0%

9

0.75

0.86

1500

80M

1LA7

BALL

1LA7 083-4AA11

311

CA-EF10

1.91

72.0%

10

0.75

0.86

1000

90S

1LA7

BALL

1LA7 090-6AA11

404

CA-EF10

2.05

69.0%

13

0.75

0.86

750

100L

1LA7

BALL

1LA7 106-8AB11

603

CA-EF10

2.15

66.0%

19

1.1

1.3

3000

80M

1LA7

BALL

1LA7 083-2AA11

338

CA-EF10

2.4

77.0%

11

1500

90S

1LA7

BALL

1LA7 090-4AA11

385

CA-EF10

2.55

77.0%

13

1000

90L

1LA7

BALL

1LA7 096-6AA11

488

CA-EF10

2.85

72.0%

16 22

1.1

1.3

750

100L

1LA7

BALL

1LA7 107-8AB11

747

CA-EF10

2.9

72.0%

1.5

1.75

3000

90S

1LA7

BALL

1LA7 090-2AA11

408

CA-EF10

3.25

79.0%

13

1.5

1.75

1500

90L

1LA7

BALL

1LA7 096-4AA11

448

CA-EF10

3.4

79.0%

16

1.5

1.75

1000

100L

1LA7

BALL

1LA7 106-6AA11

582

CA-EF10

3.9

74.0%

21

1.5

1.75

750

2.2

2.55

3000

112M

1LA7

BALL

1LA7 113-8AB11

891

CA-EF10

3.85

74.0%

24

90L

1LA7

BALL

1LA7 096-2AA11

511

CA-EF10

4.55

82.0%

16

2.2

2.55

1500

100L

1LA7

BALL

1LA7 106-4AA11

551

CA-EF10

4.7

82.0%

21

2.2

2.55

1000

112M

1LA7

BALL

1LA7 113-6AA11

729

CA-EF10

5.2

78.0%

26

2.2

2.55

750

132S

1LA7

BALL

1LA7 130-8AB11

1149

CA-EF10

5.7

75.0%

38

3

3.45

3000

100L

1LA7

BALL

1LA7 106-2AA11

618

CA-EF10

6.1

84.0%

22

3

3.45

1500

100L

1LA7

BALL

1LA7 107-4AA11

625

CA-EF10

6.4

83.0%

24

3

3.45

1000

132S

1LA7

BALL

1LA7 130-6AA11

924

CA-EF10

7.2

79.0%

38

3

3.45

750

132M

1LA7

BALL

1LA7 133-8AB11

1379

CA-EF10

7.6

77.0%

44

10-6

2007 Low Voltage AC Motors Selection and Pricing Guide

✔

✔

✔

IEC MOTORS EFF1 C.I. Frame

1.3 1.3

✔

✔ IEC MOTORS EFF1 Alum. Frame

1.1 1.1

✔

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

kW kW 50Hz 60Hz 0.06 0.07

B5 Flange, Footless

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

1LA7 Aluminum Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

✔ ✔

✔

2007 Low Voltage AC Motors Selection and Pricing Guide

10-7

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame IEC MOTORS Explosion Proof

1LA7 Aluminum Frame

kW kW 50Hz 60Hz

RPM

Frame

0.06 0.09

0.07 0.1

1500 3000

0.09

0.1

0.09

B14 Flange, Footless FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg)

Stock Model

B14 Flange, Footless FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 762 CA-EF10 7.8 86.0% 29

Part Number

56M 56M

1LA7 1LA7

BALL BALL

1LA7 050-4AB12 1LA7 050-2AA12

207 207

CA-EF10 CA-EF10

0.2 0.26

56.0% 63.0%

3 3

4

1500

56M

1LA7

BALL

1LA7 053-4AB12

208

CA-EF10

0.29

58.0%

3

4

0.1

1000

63M

1LA7

BALL

1LA7 063-6AB12

226

CA-EF10

0.44

45.0%

4

4

0.09

0.1

750

71M

1LA7

BALL

1LA7 070-8AB12

258

CA-EF10

0.36

53.0%

6

5.5

6.3

3000

132S

1LA7

BALL

1LA7 130-2AA12

0.12

0.14

3000

56M

1LA7

BALL

1LA7 053-2AA12

208

CA-EF10

0.32

65.0%

3

5.5

6.3

1500

132S

1LA7

BALL

1LA7 130-4AA12

0.12

0.14

1500

63M

1LA7

BALL

1LA7 060-4AB12

212

SA-EF20

0.42

55.0%

4

5.5

6.3

1000

132M

1LA7

BALL

1LA7 134-6AA12

0.12

0.14

750

71M

1LA7

BALL

1LA7 073-8AB12

286

CA-EF10

0.51

53.0%

6

5.5

6.3

750

160M

1LA7

BALL

0.18

0.21

3000

63M

1LA7

BALL

1LA7 060-2AA12

214

SA-EF20

0.5

63.0%

4

✔

7.5

8.6

3000

132S

1LA7

BALL

0.18

0.21

1500

63M

1LA7

BALL

1LA7 063-4AB12

225

SA-EF20

0.56

60.0%

4

✔

7.5

8.6

1500

132M

1LA7

BALL

0.18

0.21

1000

71M

1LA7

BALL

1LA7 070-6AA12

246

SA-EF20

0.67

53.0%

5

7.5

8.6

1000

160M

1LA7

BALL

0.18

0.21

750

80M

1LA7

BALL

1LA7 080-8AB 12

307

CA-EF10

0.75

51.0%

9

7.5

8.6

750

160L

1LA7

0.25

0.29

3000

63M

1LA7

BALL

1LA7 063-2AA12

225

CA-EF10

0.68

65.0%

4

11

12.6

3000

160M

1LA7

0.25

0.29

1500

71M

1LA7

BALL

1LA7 070-4AB12

233

SA-EF20

0.77

60.0%

5

✔

11

12.6

1500

160M

1LA7

BALL

1LA7 163-4AA12

1738

CA-EF10

21.5

88.5%

73

0.25

0.29

1000

71M

1LA7

BALL

1LA7 073-6AA12

271

SA-EF20

0.79

60.0%

6

✔

11

12.6

1000

160L

1LA7

BALL

1LA7 166-6AA12

2468

CA-EF10

24.5

87.5%

95

0.25

0.29

750

80M

1LA7

BALL

1LA7 083-8AB12

369

CA-EF10

1.02

55.0%

10

15

17.3

3000

160M

1LA7

BALL

1LA7 164-2AA12

2188

CA-EF10

26.5

90.0%

77

✔

15

17.3

1500

160L

1LA7

BALL

1LA7 166-4AA12

2218

CA-EF10

28.5

90.0%

85

18.5

21.3

3000

160L

1LA7

BALL

1LA7 166-2AA12

2588

CA-EF10

32

91.0%

86

0.37

0.43

3000

71M

1LA7

BALL

1LA7 070-2AA12

236

SA-EF20

1

66.0%

5

0.37

0.43

1500

71M

1LA7

BALL

1LA7 073-4AB12

257

CA-EF10

1.06

65.0%

6

0.37

0.43

1000

80M

1LA7

BALL

1LA7 080-6AA12

300

SA-EF20

1.2

62.0%

9

0.37

0.43

750

90S

1LA7

BALL

1LA7 090-8AB12

453

CA-EF10

1.14

63.0%

11

0.55

0.63

3000

71M

1LA7

BALL

1LA7 073-2AA12

262

CA-EF10

1.36

71.0%

6

✔

0.55

0.63

1500

80M

1LA7

BALL

1LA7 080-4AA12

290

CA-EF10

1.46

67.0%

9

✔

0.55

0.63

1000

80M

1LA7

BALL

1LA7 083-6AA12

341

CA-EF10

1.6

67.0%

10

✔

0.55

0.63

750

90L

1LA7

BALL

1LA7 096-8AB12

540

CA-EF10

1.58

66.0%

13

0.75

0.86

3000

80M

1LA7

BALL

1LA7 080-2AA12

300

CA-EF10

1.73

73.0%

9

0.75

0.86

1500

80M

1LA7

BALL

1LA7 083-4AA12

311

CA-EF10

1.91

72.0%

10

0.75

0.86

1000

90S

1LA7

BALL

1LA7 090-6AA12

404

CA-EF10

2.05

69.0%

13

0.75

0.86

750

100L

1LA7

BALL

1LA7 106-8AB12

603

CA-EF10

2.15

66.0%

19

1.3

3000

80M

1LA7

BALL

1LA7 083-2AA12

338

CA-EF10

2.4

77.0%

11

1.3

1500

90S

1LA7

BALL

1LA7 090-4AA12

385

CA-EF10

2.55

77.0%

13

1.1

1.3

1000

90L

1LA7

BALL

1LA7 096-6AA12

488

CA-EF10

2.85

72.0%

16

1.1

1.3

750

100L

1LA7

BALL

1LA7 107-8AB12

747

CA-EF10

2.9

72.0%

22

1.5

1.75

3000

90S

1LA7

BALL

1LA7 090-2AA12

408

CA-EF10

3.25

79.0%

13

1.5

1.75

1500

90L

1LA7

BALL

1LA7 096-4AA12

448

CA-EF10

3.4

79.0%

16 21

1.5

1.75

1000

100L

1LA7

BALL

1LA7 106-6AA12

582

CA-EF10

3.9

74.0%

1.5

1.75

750

112M

1LA7

BALL

1LA7 123-8AB12

891

CA-EF10

3.85

74.0%

24

2.2

2.55

3000

90L

1LA7

BALL

1LA7 096-2AA12

511

CA-EF10

4.55

82.0%

16

2.2

2.55

1500

100L

1LA7

BALL

1LA7 106-4AA12

551

CA-EF10

4.7

82.0%

21

2.2

2.55

1000

112M

1LA7

BALL

1LA7 113-6AA12

729

CA-EF10

5.2

78.0%

26

2.2

2.55

750

132S

1LA7

BALL

1LA7 130-8AB12

1149

CA-EF10

5.7

75.0%

38

3

3.45

3000

100L

1LA7

BALL

1LA7 106-2AA12

618

CA-EF10

6.1

84.0%

22

3

3.45

1500

100L

1LA7

BALL

1LA7 107-4AA12

625

CA-EF10

6.4

83.0%

24

3

3.45

1000

132S

1LA7

BALL

1LA7 130-6AA12

924

CA-EF10

7.2

79.0%

38

3

3.45

750

132M

1LA7

BALL

1LA7 133-8AB12

1379

CA-EF10

7.6

77.0%

44

10-8

2007 Low Voltage AC Motors Selection and Pricing Guide

RPM 3000

Frame 112M

Type 1LA7

DE Bearing BALL

4.6

1500

112M

1LA7

BALL

1LA7 113-4AA12

793

CA-EF10

8.2

85.0%

31

4.6

1000

132M

1LA7

BALL

1LA7 133-6AA12

1129

CA-EF10

9.4

80.5%

44

4.6

750

160M

1LA7

BALL

1LA7 163-8AB12

1698

CA-EF10

10

80.0%

64

983

CA-EF10

10.4

86.5%

39

1014

CA-EF10

11.4

86.0%

41

1399

CA-EF10

12.6

83.0%

52

1LA7 164-8AB12

2088

CA-EF10

13

83.5%

74

1LA7 131-2AA12

1239

CA-EF10

13.8

88.0%

48

1LA7 133-4AA12

1269

CA-EF10

15.2

87.0%

49

1LA7 163-6AA12

1818

CA-EF10

17

86.0%

74

BALL

1LA7 166-8AB12

2548

CA-EF10

17.6

85.5%

94

BALL

1LA7 163-2AA12

1698

CA-EF10

20

89.5%

68

Part Number 1LA7 113-2AA12

Stock Model ✔

✔

IEC MOTORS EFF1 C.I. Frame

1.1 1.1

kW kW 50Hz 60Hz 4 4.6

IEC MOTORS EFF1 Alum. Frame

Type

DE Bearing

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

1LA7 Aluminum Frame

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

✔

✔

✔

2007 Low Voltage AC Motors Selection and Pricing Guide

10-9

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame IEC MOTORS Explosion Proof

1LA6 Cast Iron

The 1LA6 motors, with their wide variety of options, fit in every drive system concept and cover more than 90% of all imaginable applications worldwide, suitable for indoor and outdoor applications where excellent price/performance ratio and high degree of operational reliability in severe operating atmospheres are required. This powerful energy-saving motor is less harmful to the environment thanks to reduction in CO2 emission. These industry workhorses are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications

Features for Long Life Frame & End Shields - Cast Iron construction for high degree of operational reliability in aggressive atmospheres. All motors are designed for IP55 (IEC 529), suitable for use in dusty or damp surroundings, ready for their use in the tropics. (IP56 and IP65 available)

Stator/Windings - Manufactured with premium electrical grade steel laminations and the finest copper electrical magnet wire for lower losses and improved efficiencies. A unique stator core design lowers flux density and increases cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Insulation - DURIGNIT® IR 2000, inverter-compatible up to 500 V, optionally up to 690 V. This insulation system comprised of high-grade enameled wires and insulating sheet materials combine with solvent-freeimpregnating resin. The system ensures a high level of mechanical and electrical strength as well as good serviceability and long motor life. The insulation offers general protection for the windings against corrosive gases, vapors, dust, oil and increased humidity, and resists the normal stresses of vibration. Cooling - Motors are fitted with a radialflow fan which functions independently of the direction of rotation (cooling method IC 411 to DIN EN 60034-6). The material of the external cooling fans is reinforced plastic. This material is tested and certified for a 20 year lifetime. Fan cowls are made of corrosion protected steel plate.

kW kW 50Hz 60Hz 0.75 0.86

Lubrication - The grease life, for prelubricated motors, is tailored to the bearing life. In those cases where relubrication is chosen, the motors are provided with a grease retaining system that prevents grease from entering the motor. Siemens IEC motors use a lithium based grease. Conduit Box - Cast Iron-construction, top mounted as standard, the terminal box can be ordered to either side of the motor and be rotated 90º or 180º, providing a more flexible mounting. In addition to the standard terminal box earthing, an external earthing is also made available for all motors upon request. Corrosion Resistance - Zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. (Stainless steel hardware also available)

RPM 750

Frame 100L

Type 1LA6

DE Bearing BALL

Part Number 1LA6 106-8AB60

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 611 CA-EF22 2.15 66.0% 29

1.1

1.3

750

100L

1LA6

BALL

1LA6 107-8AB60

776

CA-EF22

2.9

72.0%

32

1.5

1.75

1000

100L

1LA6

BALL

1LA6 106-6AA60

589

1.5

1.75

750

112M

1LA6

BALL

1LA6 113-8AB60

929

CA-EF22

3.9

74.0%

33

CA-EF22

3.85

74.0%

2.2

2.55

1500

100L

1LA6

BALL

1LA6 106-4AA60

553

CA-EF22

39

4.7

82.0%

33

2.2

2.55

1000

112M

1LA6

BALL

1LA6 113-6AA60

736

CA-EF22

5.2

78.0%

40

2.2

2.55

750

132S

1LA6

BALL

1LA6 130-8AB60

1170

CA-EF22

5.7

75.0%

50

3

3.45

3000

100L

1LA6

BALL

1LA6 106-2AA60

631

CA-EF22

6.1

84.0%

34

3

3.45

1500

100L

1LA6

BALL

1LA6 107-4AA60

638

CA-EF22

6.4

83.0%

36

3

3.45

1000

132S

1LA6

BALL

1LA6 130-6AA60

922

CA-EF22

7.2

79.0%

50

3

3.45

750

132M

1LA6

BALL

1LA6 133-8AB60

1410

CA-EF22

7.6

77.0%

57

4

4.6

3000

112M

1LA6

BALL

1LA6 113-2AA60

776

CA-EF22

7.8

86.0%

43

4

4.6

1500

112M

1LA6

BALL

1LA6 113-4AA60

815

CA-EF22

8.2

85.0%

45

4

4.6

1000

132M

1LA6

BALL

1LA6 133-6AA60

1140

CA-EF22

80.5%

57

4

4.6

750

160M

1LA6

BALL

1LA6 163-8AB60

1670

CA-EF22

10

80.0%

91

5.5

6.3

3000

132S

1LA6

BALL

1LA6 130-2AA60

968

CA-EF22

10.4

86.5%

53

5.5

6.3

1500

132S

1LA6

BALL

1LA6 130-4AA60

1010

CA-EF22

11.4

86.0%

55

5.5

6.3

1000

132M

1LA6

BALL

1LA6 134-6AA60

1440

CA-EF22

12.6

83.0%

66

5.5

6.3

750

160M

1LA6

BALL

1LA6 164-8AB60

2100

CA-EF22

13

83.5%

102

7.5

8.6

3000

132S

1LA6

BALL

1LA6 131-2AA60

1250

CA-EF22

13.8

88.0%

58

7.5

8.6

1500

132M

1LA6

BALL

1LA6 133-4AA60

1280

CA-EF22

15.2

87.0%

62

7.5

8.6

1000

160M

1LA6

BALL

1LA6 163-6AA60

1830

CA-EF22

17

86.0%

103

7.5

8.6

750

160L

1LA6

BALL

1LA6 166-8AB60

2620

CA-EF22

17.6

85.5%

122

11

12.6

3000

160M

1LA6

BALL

1LA6 163-2AA60

1670

CA-EF22

20

89.5%

96

11

12.6

1500

160M

1LA6

BALL

1LA6 163-4AA60

1740

CA-EF22

21.5

88.5%

100

11

12.6

1000

160L

1LA6

BALL

1LA6 166-6AA60

2510

CA-EF22

24.5

87.5%

122

15

17.3

3000

160M

1LA6

BALL

1LA6 164-2AA60

2200

CA-EF22

26.5

90.0%

105

15

17.3

1500

160L

1LA6

BALL

1LA6 166-4AA60

2250

CA-EF22

28.5

90.0%

114

18.5

21.3

3000

160L

1LA6

BALL

1LA6 166-2AA60

2640

CA-EF22

32

91.0%

115

9.4

Stock Model

IEC MOTORS EFF1 C.I. Frame

• 0.75W to 18.5kW • Dual Frequency rated • 3000, 1500, 1000 RPM - 50 Hz 3600, 1800, 1200 RPM - 60 Hz • 3 phase, 50 Hz; 230VD/400VY and 60 Hz 460VY • 3 phase, 50 Hz; 400VD/690VY and 60 Hz 460VD • All commonly used voltages (50Hz and 60Hz) available • EU/CEMEP efficiency classification EFF2 (Improved efficiency) • Class F insulation, Class B temperature rise • Continuous Duty, Suitable for Converted fed operation • CE Marked, IEC 60034 • NEMA MG1-12 available • UL and CSA label marks available • 100 through 160 frame

Rotor - A unique offset laminated rotor core design provides improved efficiency while larger bars and Aluminum end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced (IEC 60034-14) for extended bearing life.

Horizontal, Foot Mounted

IEC MOTORS EFF1 Alum. Frame

Performance Specifications

Improved Efficiency (eff2)

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

1LA6 - Cast Iron Frame

Flexible - All Siemens IEC motors are available with a wide variety of options to meet your specific motor needs.

Bearings - The bearing nominal life is specified by standard calculation (DIN ISO 281) and is achieved or exceeds by 90% if used according to instructions, if the operating conditions are below average a bearing life of 100,000 (Lh10 hours) can be achieved.

Specifications table begins on the next page

10-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

General Purpose - TEFC IEC

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

10-11

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame IEC MOTORS Explosion Proof

1MJ6 (Ex de IIC T4)

Siemens explosion-protected motors go further than the basic safety requirements. Our rugged EEx motors are completely reliable even under the most extreme conditions and under hazardous environments such as in chemical plants, the oil industry or in gas works. They comply with the strictest safety standards for the protection of life, machines and environment. All explosion-protected motors from Siemens have been tested by the German Federal Institute of Science and Technology (PTB) or by the German Coal and Steel Technology Co. (DMT).

• • • • • •

• • • • •

Features for Long Life Frame & End Shields - Cast Iron construction for high degree of operational reliability in aggressive atmospheres. All motors are designed for IP55 (IEC 529), suitable for use in dusty or damp surroundings, ready for their use in the tropics. (IP56 available) Rotor - A unique offset laminated rotor core design provides improved efficiency while larger bars and Aluminum end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced (IEC 60034-14) for extended bearing life

Insulation - DURIGNIT® IR 2000, inverter-compatible up to 500 V, optionally up to 690 V. This insulation system comprised high-grade enameled wires and insulating sheet materials combine with solvent-free-impregnating resin. The system ensures a high level of mechanical and electrical strength as well as good serviceability and long motor life. The insulation offers general protection for the windings against corrosive gases, vapors, dust, oil and increased humidity, and resists the normal stresses of vibration. Cooling - Motors are fitted with a radialflow fan which functions independently of the direction of rotation (cooling method IC 411 to DIN EN 60034-6). The material of the external cooling fans is reinforced plastic. This material is tested and certified for a 20 year lifetime. Fan cowls are made of corrosion protected steel plate. Bearings - The bearing nominal life is specified by standard calculation (DIN ISO 281) and is achieved or exceeds by 90% if used according to instructions, if the operating conditions are below average a bearing life of 100,000 (Lh10 hours) can be achieved. Lubrication - The grease life, for prelubricated motors, is tailored to the bearing life. In those cases where relubrication is chosen, the motors are provided with a grease retaining system that prevents grease from entering the motor. Siemens IEC motors use a lithium based grease.

Specifications table begins on the next page

10-12

2007 Low Voltage AC Motors Selection and Pricing Guide

Conduit Box - Aluminum-construction for frames up to 160M, Cast Ironconstruction for frames 160L and above, top mounted as standard. The terminal box can be ordered to either side of the motor and be rotated 90º or 180º (frames size 80 and above), providing a more flexible mounting. Corrosion Resistance - Zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. (Stainless steel hardware also available) Flexible - All Siemens IEC motors are available with a wide variety of options to meet your specific motor needs.

kW kW 50Hz 60Hz 0.25 0.29

Type 1MJ6

DE Bearing BALL

RPM 1500

Frame 71M

Part Number 1MJ6 070-4CB60

0.25

0.29

1000

71M

1MJ6

BALL

1MJ6 073-6CA60

0.37

0.43

0.37

0.43

3000

71M

1MJ6

BALL

1500

71M

1MJ6

BALL

0.37

0.43

1000

80M

1MJ6

0.37

0.43

750

90L

0.55

0.63

3000

0.55

0.63

0.55

0.63

0.55

0.63

750

90L

1MJ6

0.75

0.86

3000

80M

1MJ6

0.75

0.86

1500

80M

1MJ6

0.75

0.86

1000

90L

0.75

0.86

750

1.1

1.3

1.1 1.1

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 761 CA-EXD1 0.78 60.0% 20 800

CA-EXD1

0.82

63.0%

16

1MJ6 070-2CA60

769

CA-EXD1

0.98

67.0%

19

1MJ6 073-4CB60

788

CA-EXD1

1.13

64.0%

21

BALL

1MJ6 080-6CA60

825

CA-EXD1

1.18

64.0%

35

1MJ6

BALL

1MJ6 096-8CB60

1030

CA-EXD1

1.16

61.0%

28

71M

1MJ6

BALL

1MJ6 073-2CA60

793

CA-EXD1

1.38

71.0%

20

1500

80M

1MJ6

BALL

1MJ6 080-4CA60

815

CA-EXD1

1.42

71.0%

24

1000

80M

1MJ6

BALL

1MJ6 083-6CA60

884

CA-EXD1

1.67

64.0%

23

BALL

1MJ6 097-8CB60

1140

CA-EXD1

1.62

65.0%

30

BALL

1MJ6 080-2CA60

825

CA-EXD1

1.75

72.0%

24

BALL

1MJ6 083-4CA60

838

CA-EXD1

1.88

73.0%

26

1MJ6

BALL

1MJ6 096-6CA60

979

CA-EXD1

2.1

69.0%

32

100L

1MJ6

BALL

1MJ6 106-8CB60

1280

CA-EXD1

2.15

65.0%

40

3000

80M

1MJ6

BALL

1MJ6 083-2CA60

884

CA-EXD1

2.45

74.0%

26

1.3

1500

90L

1MJ6

BALL

1MJ6 096-4CA60

968

CA-EXD1

2.7

73.0%

32

1.3

1000

90L

1MJ6

BALL

1MJ6 097-6CA60

1080

CA-EXD1

2.95

72.0%

32

1.1

1.3

750

100L

1MJ6

BALL

1MJ6 107-8CB60

1530

CA-EXD1

2.9

74.0%

48

1.5

1.75

3000

90L

1MJ6

BALL

1MJ6 096-2CA60

979

CA-EXD1

3.3

78.0%

32

1.5

1.75

1500

90L

1MJ6

BALL

1MJ6 097-4CA60

1050

CA-EXD1

3.5

77.0%

35

1.5

1.75

1000

100L

1MJ6

BALL

1MJ6 106-6CA60

1260

CA-EXD1

4

75.0%

39

1.5

1.75

750

112M

1MJ6

BALL

1MJ6 113-8CB60

1820

CA-EXD1

4

74.0%

52

2.2

2.55

3000

90L

1MJ6

BALL

1MJ6 097-2CA60

1130

CA-EXD1

4.6

80.0%

35

2.2

2.55

1500

100L

1MJ6

BALL

1MJ6 106-4CA60

1250

CA-EXD1

5.1

78.0%

44

2.2

2.55

1000

112M

1MJ6

BALL

1MJ6 113-6CA60

1630

CA-EXD1

5.5

76.0%

52

2.2

2.55

750

132S

1MJ6

BALL

1MJ6 130-8CB60

2200

CA-EXD1

6

74.0%

78

3

3.45

3000

100L

1MJ6

BALL

1MJ6 106-2CA60

1410

CA-EXD1

6.2

82.0%

44

3

3.45

1500

100L

1MJ6

BALL

1MJ6 107-4CA60

1430

CA-EXD1

6.6

80.0%

47

3

3.45

1000

132S

1MJ6

BALL

1MJ6 130-6CA60

2000

CA-EXD1

7.4

78.0%

78

3

3.45

750

132M

1MJ6

BALL

1MJ6 133-8CB60

2520

CA-EXD1

7.9

76.0%

85

4

4.6

3000

112M

1MJ6

BALL

1MJ6 113-2CA60

1650

CA-EXD1

7.8

84.0%

57

4

4.6

1500

112M

1MJ6

BALL

1MJ6 113-4CA60

1670

CA-EXD1

8.5

83.0%

58

4

4.6

1000

132M

1MJ6

BALL

1MJ6 133-6CA60

2300

CA-EXD1

9.6

79.0%

85

4

4.6

750

160M

1MJ6

BALL

1MJ6 163-8CB60

3000

CA-EXD1

9.9

81.0%

119

5.5

6.3

3000

132S

1MJ6

BALL

1MJ6 130-2CA60

2020

CA-EXD1 10.5

85.0%

75

5.5

6.3

1500

132S

1MJ6

BALL

1MJ6 130-4CA60

2070

CA-EXD1 11.1

86.0%

76

5.5

6.3

1000

132M

1MJ6

BALL

1MJ6 134-6CA60

2550

CA-EXD1 12.6

83.0%

92

5.5

6.3

750

160M

1MJ6

BALL

1MJ6 164-8CB60

3560

CA-EXD1 13.3

83.0%

134

7.5

8.6

3000

132S

1MJ6

BALL

1MJ6 131-2CA60

2300

CA-EXD1 14

87.0%

82

7.5

8.6

1500

132M

1MJ6

BALL

1MJ6 133-4CA60

2420

CA-EXD1 15

86.0%

85

7.5

8.6

1000

160M

1MJ6

BALL

1MJ6 163-6CA60

3180

CA-EXD1 17.5

86.0%

134

8.6

750

160L

1MJ6

BALL

1MJ6 166-8CB60

4290

CA-EXD1 17.9

84.0%

159

11

7.5

12.6

3000

160M

1MJ6

BALL

1MJ6 163-2CA60

3140

CA-EXD1 20.5

88.0%

123

11

12.6

1500

160M

1MJ6

BALL

1MJ6 163-4CA60

3150

CA-EXD1 21.5

87.0%

128

11

12.6

1000

160L

1MJ6

BALL

1MJ6 166-6CA60

4160

CA-EXD1 24.5

87.0%

167

11

13.2

750

180L

1MJ6

BALL

1MJ6 186-8CB60

5570

CA-EXD1 26

87.0%

191

2007 Low Voltage AC Motors Selection and Pricing Guide

Stock Model

IEC MOTORS EFF1 C.I. Frame

•

.25kW to 132kW Guideline 94/9/94EG, ATEX 100a 3000, 1500, 1000 or 750 RPM 3 phase, 50 Hz; 230D/400Y V 3 phase, 50 Hz; 400D/690Y V Special voltages (50Hz and 60Hz) available Increase Energy Saving EU efficency class EFF2 Class F insulation, Class B temperature rise Continuous Duty Suitable for Converted fed operation CE Marked, IEC 60034, IEC 60079 71 through 315 frame

Stator/Windings - Manufactured with premium electrical grade steel laminations and the finest copper electrical magnet wire for lower losses and improved efficiencies. A unique stator core design lowers flux density and increases cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

Horizontal, Foot Mounted

IEC MOTORS EFF1 Alum. Frame

Performance Specifications

Improved Efficiency (eff2)

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

1MJ6 - 1MJ7 - Cast Iron Frame

ATEX Compliant

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

Explosion Proof - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

Explosion Proof - TEFC IEC Motor

10-13

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame

15

RPM 3000

Frame 160M

Type 1MJ6

DE Bearing BALL

17.3

1500

160L

1MJ6

BALL

1MJ6 166-4CA60

Part Number 1MJ6 164-2CA60

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 3830 CA-EXD1 26.5 89.0% 134 3940 CA-EXD1

28.5

89.0%

158

Stock Model

1MJ7 (Ex de IIC T4) kW kW 50Hz 60Hz 18.5 22 22

ATEX Compliant

Horizontal, Foot Mounted Part Number 1MJ7 220-8CB60

FL FL List Multiplier Amps Nom. Eff. Weight Price $ Symbol 50Hz 50Hz (kg) 8580 CA-EXD2 37.5 88.6% 325 10000 CA-EXD2

RPM 750

Frame 225S

Type 1MJ6

DE Bearing BALL

26.5

750

225M

1MJ7

BALL

1MJ7 223-8CB60

43.5

90.1%

350

15

18

1000

180L

1MJ6

BALL

1MJ6 186-6CA60

5530 CA-EXD1

29.5

89.0%

190

30

36

1000

225M

1MJ7

BALL

1MJ7 223-6CA60

9790 CA-EXD2

56

92.0%

330

15

18

750

200L

1MJ6

BALL

1MJ6 207-8CB60

7170 CA-EXD1

32

87.5%

263

30

36

750

250M

1MJ7

BALL

1MJ7 253-8CB60

12700 CA-EXD2

58

91.6%

465

18.5

21.3

3000

160L

1MJ6

BALL

1MJ6 166-2CA60

4350 CA-EXD1

32.5

91.0%

161

37

42.5

1500

225S

1MJ7

BALL

1MJ7 220-4CA60

8250 CA-EXD2

67

93.0%

325

18.5

21.3

1500

180M

1MJ6

BALL

1MJ6 183-4CA60

4860 CA-EXD1

35

90.5%

175

37

44.5

1000

250M

1MJ7

BALL

1MJ7 253-6CA60

12600 CA-EXD2

69

92.4%

440

18.5 22

22 24.5

1000 3000

200L 180M

1MJ6 1MJ6

BALL BALL

1MJ6 206-6CA60 1MJ6 183-2CA60

6650 CA-EXD1 5170 CA-EXD1

36 39

90.2% 92.0%

240 175

37

44.5

750

280S

1MJ7

BALL

1MJ7 280-8CB60

16300 CA-EXD2

70

92.7%

570

45

51

3000

225M

1MJ7

BALL

1MJ7 223-2CB60

9860 CA-EXD2

77

93.9%

335

22

25.3

1500

180L

1MJ6

BALL

1MJ6 186-4CA60

5440 CA-EXD1

41

91.2%

189

45

52

1500

225M

1MJ7

BALL

1MJ7 223-4CA60

9470 CA-EXD2

80

93.4%

355

22

26.5

1000

200L

1MJ6

BALL

1MJ6 207-6CA60

7300 CA-EXD1

42.5

90.8%

255

45

54

1000

280S

1MJ7

BALL

1MJ7 280-6CA60

15700 CA-EXD2

81

93.0%

560

3000

200L

1MJ6

BALL

1MJ6 206-2CA60

6650 CA-EXD1

53

92.3%

250

45

54

750

280M

1MJ7

BALL

1MJ7 283-8CB60

19100 CA-EXD2

84

92.8%

620

1500

200L

1MJ6

BALL

1MJ6 207-4CA60

6790 CA-EXD1

55

91.8%

247

55

62

3000

250M

1MJ7

BALL

1MJ7 253-2CB60

12000 CA-EXD2

94

93.7%

445

37

41.5

3000

200L

1MJ6

BALL

1MJ6 207-2CA60

7760 CA-EXD1

64

92.8%

266

55

63

1500

250M

1MJ7

BALL

1MJ7 253-4CA60

11800 CA-EXD2

97

94.0%

465

55

66

1000

280M

1MJ7

BALL

1MJ7 283-6CA60

18800 CA-EXD2

99

93.6%

600

55

66

750

315S

1MJ7

Roller (DE)

1MJ7 310-8CB60

24600 CA-EXD2

104

93.1%

780

75

84

3000

280S

1MJ7

BALL

1MJ7 280-2CC60

16600 CA-EXD2

128

94.7%

600

75

86

1500

280S

1MJ7

BALL

1MJ7 280-4CA60

16100 CA-EXD2

132

94.7%

630

75

90

1000

315S

1MJ7

Roller (DE)

1MJ7 310-6CA60

24700 CA-EXD2

136

93.8%

810

10-14

2007 Low Voltage AC Motors Selection and Pricing Guide

75

90

750

315M

1MJ7

Roller (DE)

1MJ7 313-8CB60

30900 CA-EXD2

140

93.6%

890

90

101

3000

280M

1MJ7

BALL

1MJ7 283-2CC60

19200 CA-EXD2

150

95.1%

640

90

104

1500

280M

1MJ7

BALL

1MJ7 283-4CA60

18400 CA-EXD2

160

95.0%

680 870

90

108

1000

315M

1MJ7

Roller (DE)

1MJ7 313-6CA60

28900 CA-EXD2

162

94.2%

110

123

3000

315S

1MJ7

Roller (DE)

1MJ7 310-2CC60

25200 CA-EXD2

186

94.8%

840

110

127

1500

315S

1MJ7

Roller (DE)

1MJ7 310-4CA60

22700 CA-EXD2

194

94.8%

870

132

148

3000

315M

1MJ7

Roller (DE)

1MJ7 313-2CC60

29500 CA-EXD2

225

95.1%

900

132

152

1500

315M

1MJ7

Roller (DE)

1MJ7 313-4CA60

26900 CA-EXD2

232

95.5%

950

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS EFF1 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

33.5 34.5

IEC MOTORS EFF1 Alum. Frame

30 30

Stock Model

IEC MOTORS Explosion Proof

IEC MOTORS Explosion Proof

kW kW 50Hz 60Hz 15 17.3

Horizontal, Foot Mounted

Explosion Proof - TEFC IEC Motor

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 Alum. Frame

1MJ6 (Ex de IIC T4)

ATEX Compliant

IEC MOTORS EFF2 Alum. Frame

Explosion Proof - TEFC IEC Motor

10-15

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame

1LA9 Aluminum Frame

The 1LA9 motors, with their wide variety of options, fit in every drive system concept and cover more than 90% of all imaginable applications worldwide, suitable for indoor and outdoor applications where light weight and excellent price/performance ratio and high degree of operational reliability are required. This powerful energy-saving motor is less harmful to the environment thanks to reduction in CO2 emission.

Performance Specifications

• •

• • • • • • •

Features for Long Life Frame & End Shields - Cast aluminum construction for exceptional heat dissipation and structural integrity. All motors are designed with degree of protection IP55 (IEC 529), suitable for use in dusty or damp surroundings, ready for their use in the tropics. (IP56 and IP65 available)

Stator/Windings - Manufactured with premium electrical grade steel laminations and the finest copper electrical magnet wire for lower losses and improved efficiencies. A unique stator core design lowers flux density and increases cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses. Insulation - DURIGNIT® IR 2000, invertercompatible up to 500 V, optionally up to 690 V. This insulation system comprised of high-grade enameled wires and insulating sheet materials combine with solvent-free-impregnating resin. The system ensures a high level of mechanical and electrical strength as well as good serviceability and long motor life. The insulation offers general protection for the windings against corrosive gases, vapors, dust, oil and increased humidity, and resists the normal stresses of vibration. Cooling - Motors are fitted with a radialflow fan which functions independently of the direction of rotation (cooling method IC 411 to DIN EN 60034-6). The material of the external cooling fans is reinforced plastic. This material is tested and certified for a 20 year lifetime. Fan cowls are made of corrosion protected steel plate. Bearings - The bearing nominal life is specified by standard calculation (DIN ISO 281) and is achieved or exceeds by 90% if used according to instructions, if the operating conditions are below average a bearing life of 100,000 (Lh10 hours) can be achieved.

Specifications table begins on the next page

Lubrication - The grease life, for prelubricated motors, is tailored to the bearing life. In those cases where relubrication is chosen, the motors are provided with a grease retaining system that prevents grease from entering the motor. Siemens IEC motors use a lithium based grease Conduit Box - Conduit Box - Cast aluminum-construction, top mounted as standard, the terminal box can be ordered to either side of the motor and be rotated 90º or 180º (frames size 80 and above), providing a more flexible mounting. In addition to the standard terminal box earthing, an external earthing is also made available for all motors. Corrosion Resistance - Zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. (Stainless steel hardware also available) Flexible - All Siemens IEC motors are available with a wide variety of options to meet your specific motor needs.

Power kW HP 50Hz 60Hz

RPM 50Hz

60Hz

Frame

0.06 0.08

1500

1800

56M

0.09 0.12

3000

3600

0.09 0.12

1500

1800

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

Type

DE Bearing

Part Number

1LA9

BALL

1LA9 050-4KA10

218

CA-EF10

0.22

0.18 61.0% 63.0%

3

56M

1LA9

BALL

1LA9 050-2KA10

218

CA-EF10

0.24

0.22 68.0% 70.0%

3

56M

1LA9

BALL

1LA9 053-4KA10

219

CA-EF10

0.31

0.26 62.0% 64.0%

4

0.12 0.16

3000

3600

56M

1LA9

BALL

1LA9 053-2KA10

219

CA-EF10

0.31

0.28 69.0% 71.0%

4

0.12 0.16

1500

1800

63M

1LA9

BALL

1LA9 060-4KA10

224

CA-EF10

0.41

0.34 66.0% 69.0%

4

0.18 0.25

3000

3600

63M

1LA9

BALL

1LA9060-2KA10

226

CA-EF10

0.48

0.43 70.0% 71.0%

4

0.18 0.25

1500

1800

63M

1LA9

BALL

1LA9 063-4KA10

241

CA-EF10

0.62

0.54 62.0% 65.0%

5

0.25 0.33

3000

3600

63M

1LA9

BALL

1LA9 063-2KA10

241

CA-EF10

0.63

0.52 70.0% 72.0%

5

0.25 0.33

1500

1800

71M

1LA9

BALL

1LA9 070-4KA10

247

CA-EF10

0.81

0.75 70.0% 69.0%

6

0.37

0.5

3000

3600

71M

1LA9

BALL

1LA9 070-2KA10

250

CA-EF10

0.94

0.87 74.0% 72.0%

6

0.37

0.5

1500

1800

71M

1LA9

BALL

1LA9 073-4KA10

276

CA-EF10

1.03

0.98 71.0% 70.0%

7

0.55 0.75

3000

3600

71M

1LA9

BALL

1LA9 073-2KA10

283

CA-EF10

1.42

1.32 75.0% 73.0%

7

0.55 0.75

1500

1800

80M

1LA9

BALL

1LA9 080-4KA10

312

SA-EF10

1.32

1.26 77.0% 75.5%

10

0.75

1

3000

3600

80M

1LA9

BALL

1LA9 080-2KA10

322

CA-EF10

1.65

1.52 80.0% 75.5%

10

0.75

1

1500

1800

80M

1LA9

BALL

1LA9 083-4KA10

338

SA-EF10

1.80

1.58 81.0% 82.5%

12

✔

0.75

1

1000

1200

90S

1LA9

BALL

1LA9 090-6KA10

442

SA-EF10

2.00

1.78 75.5% 80.0%

16

✔

1.1

1.5

3000

3600

80M

1LA9

BALL

1LA9 083-2KA10

370

SA-EF10

2.15

1.94 84.0% 82.5%

12

✔

1.1

1.5

1500

1800

90S

1LA9

BALL

1LA9 090-4KA10

419

SA-EF10

2.45

2.20 84.0% 84.0%

15

✔

1.1

1.5

1000

1200

90L

1LA9

BALL

1LA9 096-6KA10

549

SA-EF10

2.80

2.55 82.0% 85.5%

19

✔

1.5

2

3000

3600

90S

1LA9

BALL

1LA9 090-2KA10

448

SA-EF10

2.95

2.60 85.0% 84.0%

15

✔

1.5

2

1500

1800

90L

1LA9

BALL

1LA9 096-4KA10

497

SA-EF10

3.30

2.95 85.0% 84.0%

18

✔

1.5

2

1000

1200

100L

1LA9

BALL

1LA9 106-6KA10

652

SA-EF10

3.65

3.20 85.0% 86.5%

25

✔

2.2

3

3000

3600

90L

1LA9

BALL

1LA9 096-2KA10

575

SA-EF10

4.25

3.85 86.5% 85.5%

18

✔

2.2

3

1500

1800

100L

1LA9

BALL

1LA9 106-4KA10

611

SA-EF10

4.55

4.05 86.5% 87.5%

25

✔

2.2

3

1000

1200

112M

1LA9

BALL

1LA9 113-6KA60

816

SA-EF10

5.40

4.85 84.0% 87.5%

37

✔

3

4

3000

3600

100L

1LA9

BALL

1LA9106-2KA10

695

CA-EF10

5.70

4.95 87.0% 86.5%

24

3

4

1500

1800

100L

1LA9

BALL

1LA9 107-4KA10

704

CA-EF10

6.10

5.40 87.5% 87.5%

30

4

5

3000

3600

112M

1LA9

BALL

1LA9 113-2KA60

853

SA-EF10

7.40

6.10 88.5% 87.5%

35

✔

4

5

1500

1800

112M

1LA9

BALL

1LA9 113-4KA60

891

SA-EF10

8.10

6.80 88.5% 87.5%

37

✔

4

5

1000

1200

132M

1LA9

BALL

1LA9 133-6KA60

1270

SA-EF10

8.50

6.90 84.0% 87.5%

49

✔

5.5

7.5

3000

3600

132S

1LA9

BALL

1LA9 130-2KA60

1090

SA-EF10

9.90

8.80 89.5% 88.5%

43

✔

5.5

7.5

1500

1800

132M

1LA9

BALL

1LA9130-4KA60

1140

SA-EF10

10.6

9.7

89.5% 89.5%

45

✔

5.5

7.5

1000

1200

132M

1LA9

BALL

1LA9134-6KA60

1610

SA-EF10

12.0

10.8

86.0% 89.5%

64

✔

7.5

10

3000

3600

132S

1LA9

BALL

1LA9 131-2KA60

1400

SA-EF10

13.0

11.4

90.5% 89.5%

56

✔

7.5

10

1500

1800

132M

1LA9

BALL

1LA9 133-4KA60

1450

SA-EF10

14.3

12.8

90.3% 89.5%

60

✔

7.5

10

1000

1200

160M

1LA9

BALL

1LA9 163-6KA60

2090

SA-EF10

17.1

15.0

88.0% 89.5%

98

✔

11

15

3000

3600

160M

1LA9

BALL

1LA9 163-2KA60

1920

SA-EF10

19.4

17.2

91.0% 90.2%

73

✔

11

15

1500

1800

160M

1LA9

BALL

1LA9 163-4KA60

1980

CA-EF10

20.5

18.2

91.5% 91.0%

81

11

15

1000

1200

160L

1LA9

BALL

1LA9 166-6KA60

2870

SA-EF10

23.0

20.0

88.5% 90.2%

105

15

20

3000

3600

160M

1LA9

BALL

1LA9 164-2KA60

2500

CA-EF10

26.3

23.0

91.5% 90.2%

82

15

20

1500

1800

160L

1LA9

BALL

1LA9 166-4KA60

2550

CA-EF10

27.5

24.0

92.0% 91.0%

107

18.5

25

3000

3600

160L

1LA9

BALL

1LA9 166-2KA60

2980

SA-EF10

31.5

28.0

92.3% 91.0%

102

✔

✔

✔

Prices and data subject to change without notice. 3HP, 1800 RPM out of scope of EPAct

10-16

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

10-17

IEC MOTORS EFF1 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

•

90W to 18.5kW 1.15 Service Factor, 40º C ambient Dual Frequency rated 3000, 1500, 1000 RPM - 50 Hz 3600, 1800, 1200 RPM - 60 Hz 3 phase, 50 Hz, 230VD/400VY and 60 Hz, 460VY 3 phase, 50 Hz, 400VD/690VY and 60 Hz, 460VD Special voltages (50 Hz and 60 Hz) available Meets or exceeds EPAct efficiency standards (CC 032A) Class F insulation Class B temperature rise Continuous Duty, Suitable for Converted fed operation CE Marked, IEC 60034 NEMA MG1-12 available UL and CSA label marks available 56 through 160 frame

Rotor - A unique offset laminated rotor core design provides improved efficiency while larger bars and Aluminum end rings reduce resistance for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced (IEC 60034-14) for extended bearing life.

Horizontal, Foot Mounted

IEC MOTORS EFF1 Alum. Frame

• • • •

High Efficiency (eff1)

IEC MOTORS Explosion Proof

IEC MOTORS Explosion Proof

1LA9 - Aluminum Frame

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 Alum. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

1LA9 Aluminum Frame

1LA9 Aluminum Frame

IEC MOTORS Explosion Proof

DE 50Hz 60Hz Frame Type Bearing

0.06 0.08 1500

1800

56M

1LA9

BALL

Part Number 1LA9 050-4KA10-Z A11

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz 286

CA-EF10

0.22

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

0.18 61.0%

63.0

3

Power kW HP 50Hz 60Hz

RPM 50Hz

60Hz

Frame

0.06 0.08

1500

1800

56M

0.09 0.12

3000

3600

56M

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

Type

DE Bearing

Part Number

1LA9

BALL

1LA9 050-4KA11

251

CA-EF10

0.22

0.18 61.0% 63.0%

3

1LA9

BALL

1LA9 050-2KA11

251

CA-EF10

0.24

0.22 68.0% 70.0%

3

0.09 0.12 3000

3600

56M

1LA9

BALL

1LA9 050-2KA10-Z A11

286

CA-EF10

0.24

0.22 68.0% 70.0%

3

0.09 0.12

1500

1800

56M

1LA9

BALL

1LA9 053-4KA11

252

CA-EF10

0.31

0.26 62.0% 64.0%

4

0.09 0.12 1500

1800

56M

1LA9

BALL

1LA9 053-4KA10-Z A11

287

CA-EF10

0.31

0.26 62.0% 64.0%

4

0.12 0.16

3000

3600

56M

1LA9

BALL

1LA9 053-2KA11

252

CA-EF10

0.31

0.28 69.0% 71.0%

4

0.12 0.16 3000

3600

56M

1LA9

BALL

1LA9 053-2KA10-Z A11

287

CA-EF10

0.31

0.28 69.0% 71.0%

4

0.12 0.16

1500

1800

63M

1LA9

BALL

1LA9 060-4KA11

257

CA-EF10

0.41

0.34 66.0% 69.0%

4

0.18 0.25

3000

3600

63M

1LA9

BALL

1LA9 060-2KA11

259

CA-EF10

0.48

0.43 70.0% 71.0%

4

0.12 0.16 1500

1800

63M

1LA9

BALL

1LA9 060-4KA10-Z A11

292

CA-EF10

0.41

0.34 66.0% 69.0%

4

0.18 0.25 3000

3600

63M

1LA9

BALL

1LA9 060-2KA10-Z A11

294

CA-EF10

0.48

0.43 70.0% 71.0%

4

0.18 0.25

1500

1800

63M

1LA9

BALL

1LA9 063-4KA11

274

CA-EF10

0.62

0.54 62.0% 65.0%

5

0.18 0.25 1500

1800

63M

1LA9

BALL

1LA9 063-4KA10-Z A11

309

CA-EF10

0.62

0.54 62.0% 65.0%

5

0.25 0.33

3000

3600

63M

1LA9

BALL

1LA9 063-2KA11

274

CA-EF10

0.63

0.52 70.0% 72.0%

5

0.25 0.33 3000

3600

63M

1LA9

BALL

1LA9 063-2KA10-Z A11

309

CA-EF10

0.63

0.52 70.0% 72.0%

5

0.25 0.33

1500

1800

71M

1LA9

BALL

1LA9 070-4KA11

283

CA-EF10

0.81

0.75 70.0% 69.0%

6

0.25 0.33 1500

1800

71M

1LA9

BALL

1LA9 070-4KA10-Z A11

315

CA-EF10

0.81

0.75 70.0% 69.0%

6

0.37

0.5

3000

3600

71M

1LA9

BALL

1LA9 070-2KA11

286

CA-EF10

0.94

0.87 74.0% 72.0%

6

0.37

0.5

1500

1800

71M

1LA9

BALL

1LA9 073-4KA11

312

CA-EF10

1.03

0.98 71.0% 70.0%

7

0.55 0.75

3000

3600

71M

1LA9

BALL

1LA9 073-2KA11

319

CA-EF10

1.42

1.32 75.0% 73.0%

7 10

0.37

0.5

3000

3600

71M

1LA9

BALL

1LA9 070-2KA10-Z A11

318

CA-EF10

0.94

0.87 74.0% 72.0%

6

0.37

0.5

1500

1800

71M

1LA9

BALL

1LA9 073-4KA10-Z A11

344

CA-EF10

1.03

0.98 71.0% 70.0%

7

✔

0.55 0.75 3000

3600

71M

1LA9

BALL

1LA9 073-2KA10-Z A11

351

CA-EF10

1.42

1.32 75.0% 73.0%

7

0.55 0.75

1500

1800

80M

1LA9

BALL

1LA9 080-4KA11

353

SA-EF10

1.32

1.26 77.0% 75.5%

0.55 0.75 1500

1800

80M

1LA9

BALL

1LA9 080-4KA10-Z A11

391

SA-EF10

1.32

1.26 77.0% 75.5%

10

0.75

1

3000

3600

80M

1LA9

BALL

1LA9 080-2KA11

363

CA-EF10

1.65

1.52 80.0% 75.5%

10

0.75

1

3000

3600

80M

1LA9

BALL

1LA9 080-2KA10-Z A11

401

CA-EF10

1.65

1.52 80.0% 75.5%

10

0.75

1

1500

1800

80M

1LA9

BALL

1LA9 083-4KA11

379

SA-EF10

1.80

1.58 81.0% 82.5%

12

✔

0.75

1

1500

1800

80M

1LA9

BALL

1LA9 083-4KA10-Z A11

417

SA-EF10

1.80

1.58 81.0% 82.5%

12

0.75

1

1000

1200

90S

1LA9

BALL

1LA9 090-6KA11

492

SA-EF10

2.00

1.78 75.5% 80.0%

16

✔

✔

1

1000

1200

90S

1LA9

BALL

1LA9 090-6KA10-Z A11

521

SA-EF10

2.00

1.78 75.5% 80.0%

16

1.1

1.5

3000

3600

80M

1LA9

BALL

1LA9 083-2KA11

411

SA-EF10

2.15

1.94 84.0% 82.5%

12

✔

1.1

1.5

3000

3600

80M

1LA9

BALL

1LA9 083-2KA10-Z A11

449

SA-EF10

2.15

1.94 84.0% 82.5%

12

✔

1.1

1.5

1500

1800

90S

1LA9

BALL

1LA9 090-4KA11

469

SA-EF10

2.45

2.20 84.0% 84.0%

15

✔

1.1

1.5

1500

1800

90S

1LA9

BALL

1LA9 090-4KA10-Z A11

498

SA-EF10

2.45

2.20 84.0% 84.0%

15

✔

1.1

1.5

1000

1200

90L

1LA9

BALL

1LA9 096-6KA11

599

SA-EF10

2.80

2.55 82.0% 85.5%

19

1.1

1.5

1000

1200

90L

1LA9

BALL

1LA9 096-6KA10-Z A11

628

SA-EF10

2.80

2.55 82.0% 85.5%

19

1.5

2

3000

3600

90S

1LA9

BALL

1LA9 090-2KA11

498

SA-EF10

2.95

2.60 85.0% 84.0%

15

✔

2

1500

1800

90L

1LA9

BALL

1LA9 096-4KA11

547

SA-EF10

3.30

2.95 85.0% 84.0%

18

✔

90S

1LA9

BALL

1LA9 090-2KA10-Z A11

527

SA-EF10

2.95

2.60 85.0% 84.0%

15

✔

1.5

1800

90L

1LA9

BALL

1LA9 096-4KA10-Z A11

576

SA-EF10

3.30

2.95 85.0% 84.0%

18

✔

1.5

2

1000

1200

100L

1LA9

BALL

1LA9 106-6KA11

713

SA-EF10

3.65

3.20 85.0% 86.5%

25

✔

1200

100L

1LA9

BALL

1LA9 106-6KA10-Z A11

743

SA-EF10

3.65

3.20 85.0% 86.5%

25

2.2

3

3000

3600

90L

1LA9

BALL

1LA9 096-2KA11

625

SA-EF10

4.25

3.85 86.5% 85.5%

18

✔

3000

3600

90L

1LA9

BALL

1LA9 096-2KA10-Z A11

654

SA-EF10

4.25

3.85 86.5% 85.5%

18

✔

2.2

3

1500

1800

100L

1LA9

BALL

1LA9106-4KA11

672

SA-EF10

4.55

4.05 86.5% 87.5%

25

✔

3

1500

1800

100L

1LA9

BALL

1LA9 106-4KA10-Z A11

702

SA-EF10

4.55

4.05 86.5% 87.5%

25

✔

2.2

3

1000

1200

112M

1LA9

BALL

1LA9 113-6KA11

892

SA-EF10

5.40

4.85 84.0% 87.5%

37

✔

2.2

3

1000

1200

112M

1LA9

BALL

1LA9 113-6KA60-Z A11

907

SA-EF10

5.40

4.85 84.0% 87.5%

37

3

4

3000

3600

100L

1LA9

BALL

1LA9 106-2KA11

756

CA-EF10

5.70

4.95 87.0% 86.5%

24

✔

3

4

3000

3600

100L

1LA9

BALL

1LA9 106-2KA10-Z A11

786

CA-EF10

5.70

4.95 87.0% 86.5%

24

✔

3

4

1500

1800

100L

1LA9

BALL

1LA9 107-4KA11

765

CA-EF10

6.10

5.40 87.5% 87.5%

30

✔

3

4

1500

1800

100L

1LA9

BALL

1LA9 107-4KA10-Z A11

795

CA-EF10

6.10

5.40 87.5% 87.5%

30

✔

4

5

3000

3600

112M

1LA9

BALL

1LA9 113-2KA11

929

SA-EF10

7.40

6.10 88.5% 87.5%

35

✔

4

5

3000

3600

112M

1LA9

BALL

1LA9 113-2KA60-Z A11

944

SA-EF10

7.40

6.10 88.5% 87.5%

35

✔

4

5

1500

1800

112M

1LA9

BALL

1LA9 113-4KA11

967

SA-EF10

8.10

6.80 88.5% 87.5%

37

✔

4

5

1500

1800

112M

1LA9

BALL

1LA9 113-4KA60-Z A11

982

SA-EF10

8.10

6.80 88.5% 87.5%

37

✔

4

5

1000

1200

132M

1LA9

BALL

1LA9 133-6KA11

1369

SA-EF10

8.50

6.90 84.0% 87.5%

49

1.5

2

3000

3600

1.5

2

1500

1.5

2

1000

2.2

3

2.2

4

5

1000

1200

132M

1LA9

BALL

1LA9 133-6KA60-Z A11 1372

SA-EF10

8.50

6.90 84.0% 87.5%

49

5.5

7.5

3000

3600

132S

1LA9

BALL

1LA9 130-2KA11

1189

SA-EF10

8.80 89.5% 88.5%

43

✔

5.5

7.5

3000

3600

132S

1LA9

BALL

1LA9 130-2KA60-Z A11 1192

SA-EF10

9.90

8.80 89.5% 88.5%

43

✔

5.5

7.5

1500

1800

132M

1LA9

BALL

1LA9 130-4KA11

1239

SA-EF10

10.6

9.7

89.5% 89.5%

45

✔

5.5

7.5

1500

1800

132M

1LA9

BALL

1LA9 130-4KA60-Z A11 1242

SA-EF10

9.7

45

✔

5.5

7.5

1000

1200

132M

1LA9

BALL

1LA9 134-6KA11

1709

SA-EF10

12.0

10.8

86.0% 89.5%

64

✔

7.5

10

3000

3600

132S

1LA9

BALL

1LA9 131-2KA11

1499

SA-EF10

13.0

11.4

90.5% 89.5%

56

✔

10

1500

1800

132M

1LA9

BALL

1LA9 133-4KA11

1549

SA-EF10

14.3

12.8

90.3% 89.5%

60

✔

5.5

7.5

1000

1200

132M

1LA9

BALL

1LA9 134-6KA60-Z A11 1712

SA-EF10

10.6 12.0

10.8

89.5% 89.5% 86.0% 89.5%

64

9.90

7.5

10

3000

3600

132S

1LA9

BALL

1LA9 131-2KA60-Z A11 1502

SA-EF10

13.0

11.4

90.5% 89.5%

56

✔

7.5

7.5

10

1500

1800

132M

1LA9

BALL

1LA9 133-4KA60-Z A11 1552

SA-EF10

14.3

12.8

90.3% 89.5%

60

✔

7.5

10

1000

1200

160M

1LA9

BALL

1LA9 163-6KA11

2218

SA-EF10

17.1

15.0

88.0% 89.5%

98

7.5

10

1000

1200

160M

1LA9

BALL

1LA9 163-6KA60-Z A11 2192

SA-EF10

17.1

15.0

88.0% 89.5%

98

11

15

3000

3600

160M

1LA9

BALL

1LA9 163-2KA11

2048

SA-EF10

19.4

17.2

91.0% 90.2%

73

11

15

3000

3600

160M

1LA9

BALL

1LA9 163-2KA60-Z A11 2022

SA-EF10

19.4

17.2

91.0% 90.2%

73

✔

11

15

1500

1800

160M

1LA9

BALL

1LA9 163-4KA11

2108

CA-EF10

20.5

18.2

91.5% 91.0%

81

11

15

1500

1800

160M

1LA9

BALL

1LA9 163-4KA60-Z A11 2082

CA-EF10

20.5

18.2

91.5% 91.0%

81

✔

11

15

1000

1200

160L

1LA9

BALL

1LA9 166-6KA11

2998

SA-EF10

23.0

20.0

88.5% 90.2%

105

11

15

1000

1200

160L

1LA9

BALL

1LA9 166-6KA60-Z A11 2972

SA-EF10

23.0

20.0

88.5% 90.2%

105

15

20

3000

3600

160M

1LA9

BALL

1LA9 164-2KA11

2628

CA-EF10

26.3

23.0

91.5% 90.2%

82

15

20

3000

3600

160M

1LA9

BALL

1LA9 164-2KA60-Z A11 2602

CA-EF10

26.3

23.0

91.5% 90.2%

82

✔

15

20

1500

1800

160L

1LA9

BALL

1LA9 166-4KA11

2678

CA-EF10

27.5

24.0

92.0% 91.0%

107

18.5

25

3000

3600

160L

1LA9

BALL

1LA9 166-2KA11

3108

SA-EF10

31.5

28.0

92.3% 91.0%

102

15

20

1500

1800

160L

1LA9

BALL

1LA9 166-4KA60-Z A11 2652

CA-EF10

27.5

24.0

92.0% 91.0%

107

✔

18.5

25

3000

3600

160L

1LA9

BALL

1LA9 166-2KA60-Z A11 3082

SA-EF10

31.5

28.0

92.3% 91.0%

102

✔

Prices and data subject to change without notice.

Prices and data subject to change without notice. 3HP, 1800 RPM out of scope of EPAct

3HP, 1800 RPM out of scope of EPAct

10-18

2007 Low Voltage AC Motors Selection and Pricing Guide

DOE#CC032A

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

10-19

IEC MOTORS EFF1 C.I. Frame

0.75

IEC MOTORS EFF1 Alum. Frame

IEC MOTORS EFF1 Alum. Frame

RPM

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 C.I. Frame

Power kW HP 50Hz 60Hz

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF2 C.I. Frame

Horizontal, Foot Mounted, with Thermistors

B5 Flange, Footless

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame IEC MOTORS EFF2 C.I. Frame IEC MOTORS Explosion Proof

1LG6 - Cast Iron Frame

Power kW HP 50Hz 60Hz

50Hz

60Hz

Frame

0.06 0.08

1500

1800

56M

0.09 0.12

3000

3600

0.09 0.12

1500

0.12 0.16

3000

B14 Flange, Footless

RPM

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

Type

DE Bearing

Part Number

1LA9

BALL

1LA9 050-4KA12

251

CA-EF10

0.22

0.18 61.0% 63.0%

3

56M

1LA9

BALL

1LA9 050-2KA12

251

CA-EF10

0.24

0.22 68.0% 70.0%

3

1800

56M

1LA9

BALL

1LA9 053-4KA12

252

CA-EF10

0.31

0.26 62.0% 64.0%

4

3600

56M

1LA9

BALL

1LA9 053-2KA12

252

CA-EF10

0.31

0.28 69.0% 71.0%

4

0.12 0.16

1500

1800

63M

1LA9

BALL

1LA9 060-4KA12

257

CA-EF10

0.41

0.34 66.0% 69.0%

4

0.18 0.25

3000

3600

63M

1LA9

BALL

1LA9 060-2KA12

259

CA-EF10

0.48

0.43 70.0% 71.0%

4

0.18 0.25

1500

1800

63M

1LA9

BALL

1LA9 063-4KA12

274

CA-EF10

0.62

0.54 62.0% 65.0%

5

0.25 0.33

3000

3600

63M

1LA9

BALL

1LA9 063-2KA12

274

CA-EF10

0.63

0.52 70.0% 72.0%

5

0.25 0.33

1500

1800

71M

1LA9

BALL

1LA9 070-4KA12

283

CA-EF10

0.81

0.75 70.0% 69.0%

6

0.37

0.5

3000

3600

71M

1LA9

BALL

1LA9 070-2KA12

286

CA-EF10

0.94

0.87 74.0% 72.0%

6

0.37

0.5

1500

1800

71M

1LA9

BALL

1LA9 073-4KA12

312

CA-EF10

1.03

0.98 71.0% 70.0%

7

0.55 0.75

3000

3600

71M

1LA9

BALL

1LA9 073-2KA12

319

CA-EF10

1.42

1.32 75.0% 73.0%

7

The 1LG6 series of IEC motors are ideal for both indoor and outdoor applications and in severe operating atmospheres. These industry workhorses are ideal for use in chemical processing, mining, foundry, pulp and paper, waste management and petro/chemical applications.

Performance Specifications

0.55 0.75

1500

1800

80M

1LA9

BALL

1LA9 080-4KA12

353

SA-EF10

1.32

1.26 77.0% 75.5%

10

0.75

1

3000

3600

80M

1LA9

BALL

1LA9 080-2KA12

363

CA-EF10

1.65

1.52 80.0% 75.5%

10

0.75

1

1500

1800

80M

1LA9

BALL

1LA9 083-4KA12

379

SA-EF10

1.80

1.58 81.0% 82.5%

12

✔

1

1000

1200

90S

1LA9

BALL

1LA9 090-6KA12

492

SA-EF10

2.00

1.78 75.5% 80.0%

16

✔

1.1

1.5

3000

3600

80M

1LA9

BALL

1LA9 083-2KA12

411

SA-EF10

2.15

1.94 84.0% 82.5%

12

✔

1.1

1.5

1500

1800

90S

1LA9

BALL

1LA9 090-4KA12

469

SA-EF10

2.45

2.20 84.0% 84.0%

15

✔

1.1

1.5

1000

1200

90L

1LA9

BALL

1LA9 096-6KA12

599

SA-EF10

2.80

2.55 82.0% 85.5%

19

✔

1.5

2

3000

3600

90S

1LA9

BALL

1LA9 090-2KA12

498

SA-EF10

2.95

2.60 85.0% 84.0%

15

✔

1.5

2

1500

1800

90L

1LA9

BALL

1LA9 096-4KA12

547

SA-EF10

3.30

2.95 85.0% 84.0%

18

✔

1.5

2

1000

1200

100L

1LA9

BALL

1LA9 106-6KA12

713

SA-EF10

3.65

3.20 85.0% 86.5%

25

✔

2.2

3

3000

3600

90L

1LA9

BALL

1LA9 096-2KA12

625

SA-EF10

4.25

3.85 86.5% 85.5%

18

✔

2.2

3

1500

1800

100L

1LA9

BALL

1LA9106-4KA12

672

SA-EF10

4.55

4.05 86.5% 87.5%

25

✔

2.2

3

1000

1200

112M

1LA9

BALL

1LA9 113-6KA12

892

SA-EF10

5.40

4.85 84.0% 87.5%

37

✔

3

4

3000

3600

100L

1LA9

BALL

1LA9 106-2KA12

756

CA-EF10

5.70

4.95 87.0% 86.5%

24

✔

• • • • •

3

4

1500

1800

100L

1LA9

BALL

1LA9 107-4KA12

765

CA-EF10

6.10

5.40 87.5% 87.5%

30

✔

4

5

3000

3600

112M

1LA9

BALL

1LA9 113-2KA12

929

SA-EF10

7.40

6.10 88.5% 87.5%

35

✔

4

5

1500

1800

112M

1LA9

BALL

1LA9 113-4KA12

967

SA-EF10

8.10

6.80 88.5% 87.5%

37

✔

• • • •

4

5

1000

1200

132M

1LA9

BALL

1LA9 133-6KA12

1369

SA-EF10

8.50

6.90 84.0% 87.5%

49

5.5

7.5

3000

3600

132S

1LA9

BALL

1LA9 130-2KA12

1189

SA-EF10

9.90

8.80 89.5% 88.5%

43

✔

Features for Long Life

5.5

7.5

1500

1800

132M

1LA9

BALL

1LA9 130-4KA12

1239

SA-EF10

10.6

9.7

89.5% 89.5%

45

✔

5.5

7.5

1000

1200

132M

1LA9

BALL

1LA9 134-6KA12

1709

SA-EF10

12.0

10.8

86.0% 89.5%

64

✔

7.5

10

3000

3600

132S

1LA9

BALL

1LA9 131-2KA12

1499

SA-EF10

13.0

11.4

90.5% 89.5%

56

✔

7.5

10

1500

1800

132M

1LA9

BALL

1LA9 133-4KA12

1549

SA-EF10

14.3

12.8

90.3% 89.5%

60

✔

7.5

10

1000

1200

160M

1LA9

BALL

1LA9 163-6KA12

2218

SA-EF10

17.1

15.0

88.0% 89.5%

98

11

15

3000

3600

160M

1LA9

BALL

1LA9 163-2KA12

2048

SA-EF10

19.4

17.2

91.0% 90.2%

73

Frame & End Shields - Cast Iron construction for exceptional structural integrity. All motors are designed for IP55 (IEC 529), suitable for use in dusty or damp surroundings, ready for their use in the tropics. (IP56 and IP65 available)

11

15

1500

1800

160M

1LA9

BALL

1LA9 163-4KA12

2108

CA-EF10

20.5

18.2

91.5% 91.0%

81

11

15

1000

1200

160L

1LA9

BALL

1LA9 166-6KA12

2998

SA-EF10

23.0

20.0

88.5% 90.2%

105

15

20

3000

3600

160M

1LA9

BALL

1LA9 164-2KA12

2628

CA-EF10

26.3

23.0

91.5% 90.2%

82

15

20

1500

1800

160L

1LA9

BALL

1LA9 166-4KA12

2678

CA-EF10

27.5

24.0

92.0% 91.0%

107

18.5

25

3000

3600

160L

1LA9

BALL

1LA9 166-2KA12

3108

SA-EF10

31.5

28.0

92.3% 91.0%

102

Prices and data subject to change without notice.

2007 Low Voltage AC Motors Selection and Pricing Guide

Insulation - DURIGNIT® IR 2000, invertercompatible up to 500 V, optionally up to 690 V. This insulation system comprised of high-grade enameled wires and insulating sheet materials combine with solvent-free-impregnating resin. The system ensures a high level of mechanical and electrical strength as well as good serviceability and long motor life. The insulation offers general protection for the windings against corrosive gases, vapors, dust, oil and increased humidity, and resists the normal stresses of vibration. Cooling - Motors are fitted with a radialflow fan which functions independently of the direction of rotation (cooling method IC 411 to DIN EN 60034-6). The material of the external cooling fans is reinforced plastic. This material is tested and certified for a 20 year lifetime. Fan cowls are made of corrosion protected steel plate. Bearings - Non-regreasable bearings, but optionally available with regreasing devices up to frame size 250 (Standard from frame 280 and above). The bearing nominal life is specified by standard calculation (DIN ISO 281) and is achieved or exceeds by 90% if used properly, if the operating conditions are below average a bearing life of 100,000 (Lh10 hours) can be achieved.

Lubrication - The grease life, for prelubricated motors, is tailored to the bearing life. For re-lubricated bearings, the motors are provided with a grease retaining system with the provision that when the grease containing chamber is full of old grease the grease is then ejected to the outside of the motor. Conduit Box - The top mounted, Cast aluminum-construction terminal box (frames 225 and below, cast iron construction available as an option) and the Cast Iron-construction (frame 250 and above) can be ordered to the Right or left hand side of the motor as well as rotated 90º and 180º. Corrosion Resistance - Zinc-plated hardware, epoxy enamel paint and aluminum nameplate resist rust and corrosion. (Stainless steel hardware also available) Flexible - All Siemens IEC motors are available with a wide variety of options to meet your specific motor needs.

Specifications table begins on the next page

3HP, 1800 RPM out of scope of EPAct

10-20

Rotor - A unique offset laminated rotor core design provides improved efficiency while larger bars and Aluminum end rings reduce resistance

Stator/Windings - Manufactured with premium electrical grade steel laminations and the finest copper electrical magnet wire for lower losses and improved efficiencies. A unique stator core design lowers flux density and increases cooling capacity. Large conductor cross section reduces resistance, also lowering stator losses.

DOE#CC032A

2007 Low Voltage AC Motors Selection and Pricing Guide

10-21

IEC MOTORS EFF1 C.I. Frame

0.75

•

18.5kW to 200kW 1.15 service factor, 40°C ambient Dual Frequency rated 3000, 1500, 1000 RPM - 50 Hz 3600, 1800, 1200 RPM - 60 Hz 3 phase, 50 Hz; 230VD/400VY and 60 Hz; 460VY 3 phase, 50 Hz; 400VD/690VY and 60 Hz; 460VD Special voltages (50 and 60Hz) available Increase Energy Saving EU efficency class EFF1 Meets or exceeds EPAct efficiency standards (CC 032A) Class F insulation, Class B temperature rise Continuous Duty, Suitable for Converted fed operation CE Marked, IEC 60034 NEMA MG1-12 UL and CSA marks available 180 through 315 frame

for lower rotor losses. Each die cast aluminum rotor assembly is dynamically balanced (IEC 60034-14) for extended bearing life.

IEC MOTORS EFF1 Alum. Frame

• • • • • •

High Efficiency (eff1)

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

1LA9 Aluminum Frame

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF1 C.I. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

1LG6 Cast Iron

1LG6 Cast Iron

Power kW HP 50Hz 60Hz

IEC MOTORS Explosion Proof

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

50Hz

60Hz

Frame

Type

15

20

1000

1200

180L

1LG6

BALL

1LG6 186-6AA60

3690

CA-EF11

29.5

25.5

90.9% 91.0%

175

18.5

25

1500

1800

180M

1LG6

BALL

1LG6 183-4AA60

3040

SA-EF11

34.5

31

92.6% 92.4%

155

18.5

25

1000

1200

200L

1LG6

BALL

1LG6 206-6AA60

4510

CA-EF11

36

32

91.2% 91.7%

210

22

30

3000

3600

180M

1LG6

BALL

1LG6 183-2AA60

3490

SA-EF11

38.5

34

94.1% 93.6%

180

30

1500

1800

180L

1LG6

BALL

Part Number

1LG6 186-4AA60

3560

CA-EF11

40.5

36.5

93.2% 92.4%

Horizontal, Foot Mounted, with Thermistors

Power RPM kW HP DE 50Hz 60Hz 50Hz 60Hz Frame Type Bearing

Part Number

FL Current List Multiplier 400v 460v Price $ Symbol 50Hz 60Hz

FL Nom. Eff. 400v 460v Weight Stock 50Hz 60Hz (kg) Model

15

20

1000

1200

180L

1LG6

BALL

1LG6 186-6AA60-Z A11 3897

CA-EF11

29.5

25.5

90.9% 91.0%

175

18.5

25

1500

1800

180M

1LG6

BALL

1LG6 183-4AA60-Z A11 3247

SA-EF11

34.5

31

92.6% 92.4%

155

18.5

25

1000

1200

200L

1LG6

BALL

1LG6 206-6AA60-Z A11 4717

CA-EF11

36

32

91.2% 91.7%

210

22

30

3000

3600

180M

1LG6

BALL

1LG6 183-2AA60-Z A11 3697

SA-EF11

38.5

34

94.1% 93.6%

180

✔

180

22

30

1500

1800

180L

1LG6

BALL

1LG6 186-4AA60-Z A11 3767

SA-EF11

40.5

36.5

93.2% 92.4%

180

✔

30

1000

1200

200L

1LG6

BALL

1LG6 207-6AA60-Z A11 5477

CA-EF11

42.0

38.5

91.9% 91.7%

240

✔ ✔

✔

22

30

1000

1200

200L

1LG6

BALL

1LG6 207-6AA60

5270

CA-EF11

42.0

38.5

91.9% 91.7%

240

22

30

40

3000

3600

200L

1LG6

BALL

1LG6 206-2AA60

4450

CA-EF11

53

46

93.5% 92.4%

225

30

40

3000

3600

200L

1LG6

BALL

1LG6 206-2AA60-Z A11 4657

SA-EF11

53

46

93.5% 92.4%

225

✔

40

1500

1800

200L

1LG6

BALL

1LG6 207-4AA60-Z A11 4887

SA-EF11

55

48

93.3% 93.0%

225

✔

225M

1LG6

BALL

1LG6 223-6AA60-Z A11 7396

CA-EF11

56

49

93.2% 93.0%

325

30

40

1500

1800

200L

1LG6

BALL

1LG6 207-4AA60

4680

SA-EF11

55

48

93.3% 93.0%

225

✔

30

✔

30

40

1000

1200

40

1000

1200

225M

1LG6

BALL

1LG6 223-6AA60

7150

SA-EF11

56

49

93.2% 93.0%

325

37

50

3000

3800

200L

1LG6

BALL

1LG6 207-2AA60

5730

CA-EF11

64

57

94.1% 92.4%

255

37

50

3000

3800

200L

1LG6

BALL

1LG6 207-2AA60-Z A11 5937

SA-EF11

64

57

94.1% 92.4%

255

✔

37

50

1500

1800

225S

1LG6

BALL

1LG6 220-4AA60

5600

CA-EF11

67

60

94.0% 93.6%

290

37

50

1500

1800

225S

1LG6

BALL

1LG6 220-4AA60-Z A11 5846

SA-EF11

67

60

94.0% 93.6%

290

✔

37

50

1000

1200

250M

1LG6

BALL

1LG6 253-6AA60

8540

SA-EF11

69

61

93.7% 93.0%

405

37

50

1000

1200

250M

1LG6

BALL

1LG6 253-6AA60-Z A11 8786

CA-EF11

69

61

93.7% 93.0%

405

45

60

3000

3600

225M

1LG6

BALL

1LG6 223-2AA60

6880

CA-EF11

77

67

94.9% 94.1%

330

45

60

3000

3600

225M

1LG6

BALL

1LG6 223-2AA60-Z A11 7126

SA-EF11

77

67

94.9% 94.1%

330

✔

45

60

1500

1800

225M

1LG6

BALL

1LG6 223-4AA60

6660

CA-EF11

81

70

94.5% 94.1%

330

45

60

1500

1800

225M

1LG6

BALL

1LG6 223-4AA60-Z A11 6906

SA-EF11

81

70

94.5% 94.1%

330

✔

45

60

1000

1200

280S

1LG6

BALL

1LG6 280-6AA60

10300

CA-EF11

81

72

94.4% 94.1%

520

45

60

1000

1200

280S

1LG6

BALL

1LG6 280-6AA60-Z A11 10606

CA-EF11

81

72

94.4% 94.1%

520

55

75

3000

3600

250M

1LG6

BALL

1LG6 253-2AA60

8180

CA-EF11

93

84

95.3% 93.6%

420

55

75

3000

3600

250M

1LG6

BALL

1LG6 253-2AA60-Z A11 8426

SA-EF11

93

84

95.3% 93.6%

420

✔

55

75

1500

1800

250M

1LG6

BALL

1LG6 253-4AA60

7940

CA-EF11

96

86

95.1% 94.5%

460

55

75

1500

1800

250M

1LG6

BALL

1LG6 253-4AA60-Z A11 8186

SA-EF11

96

86

95.1% 94.5%

460

✔

75

1000

1200

280M

1LG6

BALL

1LG6 283-6AA60-Z A11 12606

CA-EF11

99

89

94.6% 94.5%

570

✔

75

1000

1200

280M

1LG6

BALL

1LG6 283-6AA60

12300

CA-EF11

99

89

94.6% 94.5%

570

75

100

3000

3600

280S

1LG6

BALL

1LG6 280-2AB60

10800

CA-EF11 128

110

95.2% 95.0%

530

75

100

3000

3600

280S

1LG6

BALL

1LG6 280-2AB60-Z A11 11106

CA-EF11 128

110

95.2% 95.0%

530

575

75

100

1500

1800

280S

1LG6

BALL

1LG6 280-4AA60-Z A11 10706

SA-EF11 130

114

95.1% 95.0%

575

100

1000

1200

315S

1LG6

BALL

1LG6 310-6AA60-Z A11 15906

CA-EF11 138

120

95.0% 94.5%

760

75

100

1500

1800

280S

1LG6

BALL

1LG6 280-4AA60

10400

CA-EF11 130

114

95.1% 95.0%

75

100

1000

1200

315S

1LG6

BALL

1LG6 310-6AA60

15600

CA-EF11 138

120

95.0% 94.5%

760

75

90

125

3000

3600

280M

1LG6

BALL

1LG6 283-2AB60

12700

CA-EF11 150

136

95.6% 95.0%

615

90

125

3000

3600

280M

1LG6

BALL

1LG6 283-2AB60-Z A11 13006

CA-EF11 150

136

95.6% 95.0%

615

90

125

1500

1800

280M

1LG6

BALL

1LG6 283-4AA60-Z A11 12206

SA-EF11 158

144

95.4% 95.0%

675 935

90

125

1500

1800

280M

1LG6

BALL

1LG6 283-4AA60

11900

CA-EF11 158

144

95.4% 95.0%

675

90

125

1000

1200

315M

1LG6

BALL

1LG6 313-6AA60

18600

CA-EF11 160

148

95.3% 94.5%

935

90

125

1000

1200

315M

1LG6

BALL

1LG6 313-6AA60-Z A11 18906

CA-EF11 160

148

95.3% 94.5%

110

150

3000

3600

315S

1LG6

BALL

1LG6 310-2AB60

15600

CA-EF11 182

164

95.8% 94.5%

790

110

150

3000

3600

315S

1LG6

BALL

1LG6 310-2AB60-Z A11 15906

CA-EF11 182

164

95.8% 94.5%

790

110

150

1500

1800

315S

1LG6

BALL

1LG6 310-4AA60

14800

CA-EF11 190

170

95.9% 95.0%

810

110

150

1500

1800

315S

1LG6

BALL

1LG6 310-4AA60-Z A11 15106

SA-EF11 190

170

95.9% 95.0%

810

110

150

1000

1200

315L

1LG6

BALL

1LG6 316-6AA60

22400

CA-EF11 196

176

95.6% 95.0% 1010

110

150

1000

1200

315L

1LG6

BALL

1LG6 316-6AA60-Z A11 22706

CA-EF11 196

176

95.6% 95.0% 1010

132

175

3000

3600

315M

1LG6

BALL

1LG6 313-2AB60

18600

CA-EF11 220

190

96.0% 95.0%

915

132

175

3000

3600

315M

1LG6

BALL

1LG6 313-2AB60-Z A11 18906

CA-EF11 220

190

96.0% 95.0%

915

132

175

1500

1800

315M

1LG6

BALL

1LG6 313-4AA60

17700

CA-EF11 225

198

96.1% 95.4%

965

132

175

1500

1800

315M

1LG6

BALL

1LG6 313-4AA60-Z A11 18006

CA-EF11 225

198

96.1% 95.4%

965

132

175

1000

1200

315L

1LG6

BALL

1LG6 317-6AA60

26600

CA-EF11 235

205

95.8% 95.4% 1180

132

175

1000

1200

315L

1LG6

BALL

1LG6 317-6AA60-Z A11 26906

CA-EF11 235

205

95.8% 95.4% 1180

160

200

3000

3600

315L

1LG6

BALL

1LG6 316-2AB60

23000

CA-EF11 260

215

96.4% 95.4% 1055

160

200

3000

3600

315L

1LG6

BALL

1LG6 316-2AB60-Z A11 23306

CA-EF11 260

215

96.4% 95.4% 1055

160

200

1500

1800

315L

1LG6

BALL

1LG6 316-4AA60

21700

CA-EF11 275

225

96.3% 95.4% 1105

160

200

1500

1800

315L

1LG6

BALL

1LG6 316-4AA60-Z A11 22006

CA-EF11 275

225

96.3% 95.4% 1105

95.8% 95.4% 1245

160

200

1000

1200

315L

1LG6

BALL

1LG6 318-6AA60-Z A11 32506

CA-EF11 280

235

95.8% 95.4% 1245

96.5% 95.4% 1245

200

250

3000

3600

315L

1LG6

BALL

1LG6 317-2AB60-Z A11 29006

CA-EF11 320

265

96.5% 95.4% 1245

96.4% 95.8% 1305

200

250

1500

1800

315L

1LG6

BALL

1LG6 317-4AA60-Z A11 27306

CA-EF11 340

280

96.4% 95.8% 1305

160 200 200

200 250 250

1000 3000 1500

1200 3600 1800

315L 315L 315L

1LG6 1LG6 1LG6

BALL BALL BALL

1LG6 318-6AA60 1LG6 317-2AB60 1LG6 317-4AA60

Note: DOE# CC032A The following are out of the scope of EPAct: 1LA6 253, 280 2-pole 1LA6 220, 253 4-pole 1LA6 253, 283 6-pole

10-22

2007 Low Voltage AC Motors Selection and Pricing Guide

32200 28700 27000

CA-EF11 280 CA-EF11 320 CA-EF11 340

235 265 280

✔

✔

✔

Note: DOE# CC032A The following are out of the scope of EPAct: 1LA6 253, 280 2-pole 1LA6 220, 253 4-pole 1LA6 253, 283 6-pole

2007 Low Voltage AC Motors Selection and Pricing Guide

10-23

IEC MOTORS EFF1 C.I. Frame

55

55

IEC MOTORS EFF1 Alum. Frame

30

IEC MOTORS Explosion Proof

IEC MOTORS EFF1 Alum. Frame

RPM DE Bearing

22

IEC MOTORS EFF1 C.I. Frame

Horizontal, Foot Mounted

IEC MOTORS EFF2 C.I. Frame

IEC MOTORS EFF2 C.I. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

General Purpose - TEFC IEC Motor

IEC MOTORS EFF2 Alum. Frame

IEC MOTORS Delivery Time

Notes

Delivery Time 10 -12 Weeks

12 - 14 Weeks

1LA6 / 1LA7 / 1LA9 Frames

14 - 16 Weeks

18 - 20 Weeks

22 Weeks

180 - 225

250 - 280

315

225

250 - 280

315

56 - 160

1LG6 Frames 1MJ6 Frames

71 - 200

1MJ7 Frames

IEC MOTORS Typical Performance

IEC MOTORS Explosion Proof

IEC MOTORS Special Options

IEC MOTORS EFF2 C.I. Frame

Standard Motor

Motors with Special Options 10 -12 Weeks

12 - 14 Weeks

14 - 16 Weeks

56 - 160

56 - 160

1LA6 / 1LA7 / 1LA9 Frames

IEC MOTORS EFF1 Alum. Frame

B02 C22 C23 C24 C25

D01 K45 D30 K46 D31 K50 D40 K52 K20 K40

K09 L13 K10 M72 K83 M73 K84 Y82

22 Weeks

250 - 280

315

A60 D32 K35 L12

1LG6 Frames

180 - 225

IEC MOTORS Dimensions

A10 A11 A12 A23 A31

18 - 20 Weeks

* also for frames 180 - 225

IEC MOTORS EFF1 C.I. Frame

A10 A11 A12 A23 A31 A60

1MJ6 Frames

71-200

71-200

A11 B02 D01 K52 K09 L13 A12 C22 K45 K10 Y82 A15 C23 K46 K83 A16 C24 K84 C25

D32 K53 K15 K35

1MJ7 Frames

B02 D30 K45 K09 L36 C22 K46 K10 M72 C23 K50 K83 C24 K52 K84 Y82 C25 K20 K15 K40 K35

225

A10 A11 A12 A23 A31 A60

B02 C22 C23 C24 C25

D30 K45 D31* K46 D32*K50 D40*K52 K20 K40

K09 K10 K83 K84 K15 K35

L36 M72 M73* Y82

250-280

A10 B02 A11 C22 A12 C23 A23 C24 A31 C25 A60

D30 D31 D32 D40

K45 K46 K50 K52 K20 K40

K09 K10 K83 K84 K15 K35

L36 M72 M73 Y82

315

* also for frames 225 A11 A12 A15 A16

B02 D32 K45 K09 L13 C22 K46 K10 Y82 C23 K20 K83 C24 K40 K84 C25 K15

A11 B02 D32 K52* K09 L13 A12 C22 K53* K10 Y82 A15 C23 K45 K83 A16 C24 K46 K84 C25 K20 K15 K40 K35*

A11 B02 D32 K52 K09 L13 A12 C22 K53 K10 Y82 A15 C23 K45 K83 A16 C24 K46 K84 C25 K20 K15 K40 K35

The standard delivery times are valid after the reception of a technically and commercially clarified order, on FCA Little Rock, AR basis. For determination of the arrival date at the customer, the relevant transfer times have to be added. The standard delivery times indicated according to price list can change under certain preconditions. (e.g. high volume of new orders).

10-24

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

11-1

Table of Contents 1LA6 / 1LA7 / 1LA9 Frames size 56-160

1MJ7 Frames size 225-315

IEC MOTORS Special Options

IEC MOTORS Special Options

Special Options

IEC MOTORS Typical Performance

IEC MOTORS Delivery Time

IEC MOTORS Delivery Time

Notes

1LG6 Frames size 180-315 1MJ6 Frames size 71-200

IEC MOTORS Typical Performance

Voltage Mounting

IEC MOTORS Dimensions

IEC MOTORS Dimensions

Protective Devices Cooling Temperature Country Specific Designs Motor Protection Anti-Condensation Heaters Mechanical Others

11-2

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

12-1

IEC MOTORS Delivery Time

Mounting

IEC MOTORS Typical Performance

List Price Adder ($) Frame Size

Position 12

Frame Size

56

63

71

80

90

315

Code

1

230VD / 400VY 50 Hz - 460VY 60Hz

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

0

6

400VD / 690VY 50 Hz - 460VD 60Hz

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

B3 Foot Monted - IMB3 / IMV5 /IMV6 (No canopy)

9

See Available Voltages Below

21

21

25

28

33

41

49

63

78

1

Code

Description

100 112 132

160 180

Code

Description 230VD / 400VY 50 Hz - 460VY 60Hz

6

230VD / 400VY 50 Hz - 460VY 60Hz

9

See Available Voltages Below

311

List Price Adder ($) Frame Size

71

80

90

100

112

132

160

180

200

225

250

280

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

°

25

28

33

41

49

63

78

101 116

315 °

°

°

°

°

163

186

240

311

Description

56

63

71

80

90

°

°

°

°

°

°

°

°

°

B5 Flange - IMB5 / IMV3 / IMV1 (No Canopy)

33

33

36

41

50

61

76

99

128

2

B14 Flange - IMV14 / IMV19 / IMV18 (No canopy)

33

33

36

41

50

61

76

99

128

4

B5 Flange - IMV1 with canopy

-

65

73

84

100

116 139 179

241

347 463

609 750 992 13802)

6

B5 Flange with Feet - IMB35 (No Canopy)

47

47

50

55

63

76

100 125

181

274 360

532 725 942 1240

7

B14 Flange with Feet - IMB34 (No Canopy)

47

47

50

55

63

76

100 125

181

9

Special mounting

1)

L2R L2T

60 Hz

L2V

Part Number Position 11-1LXX NNN XX

440VD

L1R

460VD

L1L

575VD

L1D

220VD / 380VY 50 Hz

List Price Adder ($) Frame Size

380VD / 660VY

160 180 °

200 °

203 247 -

-

-

-

225 250 280 °

°

315

°

°

318 383 557 7931) -

-

-

-

-

-

-

-

Consult Factory

2 Pole

1150

4-8 Pole

793

2 Pole 60 Hz

Consult

315L

100 112 132

2)

2 Pole 315L

IEC MOTORS Dimensions

1

163 186 240

1MJ7 Frames 225-315

List Price Adder ($) Frame Size

Frame Size

225 250 280

104 119

1MJ6 Frames 71-200 Position 11

200

1LG6 Frames 180-315

List Price Adder ($) Frame Size

1710

4-8 Pole

1380

2 Pole 60 Hz

Consult

415VD

1MJ6 Frames 71-200

N + LNX

Position 12 Code

Frame Size Description

1MJ7 Frames 225-315

List Price Adder ($) Frame Size

List Price Adder ($) Frame Size

71

80

90

100

112

132

160

180

200

225

250

280

°

°

°

°

°

°

°

°

°

°

°

°

°

B5 Flange - IMB5 / IMV3 / IMV1 (No Canopy)

58

65

76

92

116

157

211

505

641

800

1050

2

B14 Flange - IMV14 / IMV19 / IMV18 (No canopy)

58

65

76

-

-

-

-

-

-

-

-

4

B5 Flange - IMV1 with canopy

101 118

134

157

192

254

344

553 679

847

1060 1310

1740

6

B5 Flange with Feet - IMB35 (No canopy)

72

76

94

116

150

242

370

433 505

641

863

1130

1480

7

B14 Flange with Feet - IMB34 (No Canopy)

72

76

94

-

-

-

-

-

-

-

-

9

Special mounting

0

B3 Foot Monted - IMB3 / IMV5 /IMV6 (No canopy)

1

342 403 -

-

-

-

315

Consult Factory

Part Number Position 12-1LXX NNN XX N

12-2

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

Frame Size

1LA6 / 1LA7 / 1LA9 Frames 56-160

1LG6 Frames 180-315

List Price Adder ($) Frame Size

IEC MOTORS Special Options

IEC MOTORS Special Options

1LA6 / 1LA7 / 1LA9 Frames 56-160 Position 11

IEC MOTORS Delivery Time

Voltage

2007 Low Voltage AC Motors Selection and Pricing Guide

12-3

IEC MOTORS Delivery Time

Cooling Temperature

Description

225 250

280

315

Code

246 246

306

306

C22

306

306

513

513

63

71

80

90 100 112

132

160 180

200

-

68

68

79

79

91

91

102

102

68

68

79

79

91

91

102

102

207 207

246 246

116 116 134 134 154 154

174

174

344 344

413 413

1140

A10

3 x PTC Thermistors Tripping - VFD Zone2

A11

3 x PTC Thermistors Trippinig

A12

6 x PTC Thermistors Alarm and Tripping 116

A23

Motor temp. sensor KTY-84-130

68

68

68

79

79

91

102

102

388 388

388 772

772

A31

Temperature sensor Tripping

76

76

76

89

89 101 101

115

115

231 231

276 276

342

342

A60

6 X RTD PT100 Alarm and Tripping

-

-

-

-

- 1150 1150 1150 1150 1150 1150 1150 1260 1260

1260

68

91

207 207

1MJ6 Frames 71-200

Description

56

63

71

80

90 100 112

132

160 180

200

225 250

280

315

THCL.F, acc. to B, Cooling Temp. 45ºC, Power reduction 4%

31

31

31

31

31

37

37

49

49

62

62

70

70

83

83

C23

THCL.F, acc. to B, Cooling Temp. 50ºC, Power reduction 8%

31

31

31

31

31

37

37

49

49

62

62

70

70

83

83

C24

THCL.F, acc. to B, Cooling Temp. 55ºC, Power reduction 13%

42

42

49

56

66

82

99

126

156

202 247

365 459

588

764

C25

THCL.F, acc. to B, Cooling Temp. 60ºC, Power reduction 18%

42

42

49

56

66

82

99

126

156

202 247

365 459

588

764

1MJ7 Frames 225-315

List Price Adder ($) Frame Size 71

List Price Adder ($) Frame Size

List Price Adder ($) Frame Size

80

90

100

112

132

160

180

200

225

250

280

1MJ6 Frames 71-200

315

1MJ7 Frames 225-315

List Price Adder ($) Frame Size

Frame Size

List Price Adder ($) Frame Size

A11

3 x PTC Thermistors Tripping

302 312

312

325

325

337

337

512 512

546

546

618

618

A12

6 x PTC Thermistors Alarm and Tripping 512 529

529

556

556

571

571

821 821

916

916

980

980

Code

71

80

90

100

112

132

160

180

200

A15

3 x PTC Thermistors Tripping - VFD

347 358

358

372

372

385

385

531 531

618

618

915

915

C22

31

31

31

37

37

49

49

62

62

70

70

83

83

A16

6 x PTC Thermistors Alarm and Tripping - VFD

575 575

575

575

575

575

575

986 986

1130 1130 1340

1340

THCL.F, acc. to B, Cooling Temp. 45ºC, Power reduction 4%

C23

THCL.F, acc. to B, Cooling Temp. 50ºC, Power reduction 8%

31

31

31

37

37

49

49

62

62

70

70

83

83

C24

THCL.F, acc. to B, Cooling Temp. 55ºC, Power reduction 13%

51

58

68

85

102

130

156

202 256

379

477

612

794

C25

THCL.F, acc. to B, Cooling Temp. 60ºC, Power reduction 18%

51

58

68

85

102

130

156

202 256

379

477

612

794

2007 Low Voltage AC Motors Selection and Pricing Guide

12-5

Part Number Position 1LXX NNN XX NN - Z +

Description

225

250

280

315

Part Number Position 1LXX NNN XX NN - Z +

12-4

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS Dimensions

Code

Description

1LG6 Frames 180-315

List Price Adder ($) Frame Size

Frame Size

56

Frame Size IEC MOTORS Dimensions

List Price Adder ($) Frame Size

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

Frame Size

1LA6 / 1LA7 / 1LA9 Frames 56-160

1LG6 Frames 180-315

List Price Adder ($) Frame Size

IEC MOTORS Special Options

IEC MOTORS Special Options

1LA6 / 1LA7 / 1LA9 Frames 56-160

Code

IEC MOTORS Delivery Time

Protective Devices

IEC MOTORS Delivery Time

Motor Protection

Code

63

71

80

90 100 112

31

31

31

31

D30

Electrical acc. to NEMA MG1-1 (Standard for 1LA9)

31

31

31

31

31

31

31

31

31

D31

Designed to UL with “recognition mark” 51

54

58

62

69

76

91

116

141

190 254

318 383

510

632

D32

China Ex-Zone 2 Certificate

124 124 124 124 167 167

167

176

176 255

255 337

494

588

D40

Canadian standards (CSA)

116

141

190 254

318 383

510

632

IEC MOTORS Typical Performance

51

54

58

62

69

-

76

-

132 -

91

160 180 -

-

Description

71

80

90

100

112

-

280

315

Code

Description

56

63

71

80

90 100 112

132

160 180

-

-

M72

Version for Zone 2 main operation

-

68

82

98 108 129 153

194

259

353 459

M73

Version for Zone 2 VFD operation

-

239 272 303 312 338 360

418

494

674 876 1050 1280 1510 1810

K50

Degree of protection IP65

114 114 114 114 114 114 114

114

170

227 283

341

398

454

511

K52

Degree of protection IP56

125 125 125 125 125 125 125

125

187

249 312

375

437

500

561

Standard

1MJ7 Frames 225-315 List Price Adder ($) Frame Size

132

1MJ6 Frames 71-200

160

180

200

-

-

D01

CCC China Compulsory Certification 1)

31

31

31

-

-

-

-

D32

China Explosion proof Certificate

124 124

124

167

167

167

176

176 255

225

250

280

Code

315

-

-

-

-

255

337

494

588

Description

71

225 250

280

315

553

788

941

670

1MJ7 Frames 225-315

List Price Adder ($) Frame Size

Frame Size

200

List Price Adder ($) Frame Size

80

90

100

112

132

160

180

K52

Degree of protection IP56

197 197

197

216

216

216

216

479 525

K53

Ex d - Terminal Box

673 673

673

673

897

942

942

-

200 -

225 555

250 711

280

315

815

909

3760 4200 4680

5150

Part Number Position 1LXX NNN XX NN - Z +

Part Number Position 1LXX NNN XX NN - Z +

1)

CCC Certificate Requirements 2 Pole Motors: ≤ 2.2 kw 4 Pole Motors: ≤ 1.1 kw 6 Pole Motors: ≤ 0.75 kw 8 Pole Motors: ≤ 0.55 kw

12-6

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

12-7

IEC MOTORS Dimensions

Code

225 250

-

List Price Adder ($) Frame Size

Frame Size

200

List Price Adder ($) Frame Size

IEC MOTORS Typical Performance

56

1LG6 Frames 180-315

List Price Adder ($) Frame Size

Frame Size

31

1MJ6 Frames 71-200

IEC MOTORS Dimensions

1LA6 / 1LA7 / 1LA9 Frames 56-160

List Price Adder ($) Frame Size

CCC China Compulsory Certification (Only 1LA7 and 1LA9) 1)

D01

Description

1LG6 Frames 180-315

List Price Adder ($) Frame Size

IEC MOTORS Special Options

IEC MOTORS Special Options

1LA6 / 1LA7 / 1LA9 Frames 56-160 Frame Size

IEC MOTORS Delivery Time

Country Specific Designs

IEC MOTORS Delivery Time

Mechanical List Price Adder ($) Frame Size

Frame Size

132

160 180

200

225 250

280

315

Code

56

63

71

80

90 100 112

132

160 180

200

225 250

280

315

Anti-condensation heating for 230V Consult with factory for Zone 2

278

278 278 278 278 313 325 347

391 435

482 553 665

686

686

K09

Terminal Box on Right Hand Side (View from DE)

-

-

-

27

31

79

86

92

99

250

336 387 664

918

1170

K46

Anti-condensation heating for 115V Consult with factory for Zone 2

278

278 278 278 278 313 325 347

391 435

482 553 665

686

686

K10

Terminal Box on Left Hand Side (View from DE)

-

-

-

27

31

79

86

92

99

250

336 387 664

918

1170

K83

Rotation of terminal box 90º (entry from DE)

12

12

14

15

18

45

56

74

91

34

44

54

65

78

94

1MJ7 Frames 225-315

K84

Rotation of terminal box 90º (entry from NDE)

12

12

14

15

18

45

56

74

91

34

44

54

65

78

94

List Price Adder ($) Frame Size

K15

Cast Iron Terminal Box Standard for 1LA6 motors

-

-

-

-

-

-

-

-

-

297

394 580

K35

Metal Fan

L36

Steel plate fan cover

Description

56

63

71

80

90 100 112

1MJ6 Frames 71-200 List Price Adder ($) Frame Size

Frame Size Code

71

80

90

100

112

132

160

180

200

225

250

280

315

335 335

335

375

400

417

585

653 717

820

909

1030

1030

Anti-condensation heating for 230V Not possible with PTC's up to frame 160 Only 3 PTC for 1MJ7 motors

335 335

335

375

400

417

585

653 717

820

909

1030

1030

114 114 114 114 143 170 198 -

-

-

-

-

-

-

-

227 255 -

64

1MJ6 Frames 71-200

Code

Part Number Position 1LXX NNN XX NN - Z +

Description

283 312 341

369

398

79

162

177

88

126

1MJ7 Frames 225-315

List Price Adder ($) Frame Size

Frame Size

Standard

List Price Adder ($) Frame Size

71

80

90

100

112

132

160

180

K09

Terminal Box on Right Hand Side (View from DE)

-

-

88

92

99

108

157

250 336

387

664

918

1170

K10

Terminal Box on Left Hand Side (View from DE)

-

-

88

92

99

108

157

250 336

387

664

918

1170

K83

Rotation of terminal box 90º (entry from DE)

22

25

30

39

49

65

75

82

91

100

111

122

133

K84

Rotation of terminal box 90º (entry from NDE)

22

25

30

39

49

65

75

82

91

100

111

122

133

K15

Cast Iron Terminal Box Standard 160 frame

600 600

600

600

815

863

863 1020 1020 1020

K35

Metal Fan

-

143

170

198

227

-

-

200

318 318

225

562

250

280

315

Standard 599

599

679

Part Number Position 1LXX NNN XX NN - Z +

12-8

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

12-9

IEC MOTORS Dimensions

K46

Description Anti-condensation heating for 230V Not possible with PTC's up to frame 160 Only 3 PTC for 1MJ7 motors

Description

List Price Adder ($) Frame Size

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

List Price Adder ($) Frame Size

1LG6 Frames 180-315

List Price Adder ($) Frame Size

K45

Code

K45 IEC MOTORS Dimensions

1LA6 / 1LA7 / 1LA9 Frames 56-160

1LG6 Frames 180-315

IEC MOTORS Special Options

IEC MOTORS Special Options

1LA6 / 1LA7 / 1LA9 Frames 56-160 Frame Size

IEC MOTORS Delivery Time

Anti-Condensation Heaters

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor 1LA7 Aluminum Frame

IEC MOTORS Typical Performance

Code K45

Description K20 Bearing for increased cantilever forces

56

63

71

80

-

-

-

-

List Price Adder ($) Frame Size

90 100 112 -

76

89

132

160 180

200

225 250

280

315

100

133 191

221 249 288

323

360

K40

Regreasing device

-

-

-

-

Y82

Auxiliary nameplate (clear text is required)

31

31

31

31

Factory Test Certificate acc. to 3.1 EN 10 204

22

L12

Drain holes

34

40

46

51

57

62

68

74

79

L13

External earthing

18

18

18

18

18

22

22

22

22

B02

22

22

- 240 246 252 31

22

22

31 22

31 22

274 288

31 22

31 22

52 22

Code K20

Description Bearing for increased cantilever forces

L13

22

External earthing

Part Number Position 1LXX NNN XX NN - Z +

22

22

22

22

22 Standard

22

22

63.0

62.0

0.81

0.3

2.0

2.3

0.00015

41

57.0

0.77

0.6

1.9

1.9

0.00027

42

0.66

1.0

1.8

1.9

0.00037

39

0.09

0.11

750

630

71M

0.36

2.2

53.0

54.5

0.68

1.4

1.9

1.7

0.0008

36

0.12

0.14

3000

2800

56M

0.32

3.7

65.0

64.0

0.83

0.4

2.1

2.4

0.00015

41

Standard

0.12

0.14

1500

1350

63M

0.42

2.8

55.0

54.0

0.75

0.9

1.9

2.0

0.00029

42

Standard

0.12

0.14

750

645

71M

0.51

2.2

53.0

49.5

0.64

1.8

2.2

2.0

0.0008

36

0.18

0.21

3000

2820

63M

0.50

3.7

63.0

62.0

0.82

0.6

2.0

2.2

0.00018

49

22

22

22

83

22

22

0.18

0.21

1500

1350

63M

0.56

3.0

60.0

60.0

0.77

1.3

1.9

1.9

0.00037

42

1MJ7 Frames 225-315

0.18

0.21

1000

835

71M

0.67

2.3

53.0

54.5

0.73

2.0

2.1

1.9

0.00055

39

List Price Adder ($) Frame Size

0.18

0.21

750

675

80M

0.75

2.3

51.0

49.5

0.68

2.5

1.7

1.9

0.0014

41

0.25

0.29

3000

2830

63M

0.68

4.0

65.0

65.0

0.82

0.8

2.0

2.2

0.00022

49

0.25

0.29

1500

1350

71M

0.77

3.0

60.0

60.0

0.78

1.8

1.9

1.9

0.00052

44

0.25

0.29

1000

829

71M

0.79

2.7

60.0

58.5

0.76

2.8

2.2

2.0

0.0008

39

0.25

0.29

750

685

80M

1.02

2.6

55.0

50.5

0.64

3.5

2.0

2.2

0.0017

41

0.37

0.43

3000

2740

71M

1.00

3.5

66.0

65.0

0.82

1.3

2.3

2.3

0.00029

52

0.37

0.43

1500

1369

71M

1.06

3.3

65.0

65.0

0.78

2.6

1.9

2.1

0.00077

44

0.37

0.43

1000

919

80M

1.20

3.1

62.0

60.5

0.72

3.8

1.9

2.1

0.0014

40

0.37

0.43

750

675

90S

1.14

2.9

63.0

62.0

0.75

5.2

1.6

1.8

0.0023

41

0.55

0.63

3000

2800

71M

1.36

4.3

71.0

70.0

0.82

1.9

2.5

2.6

0.00041

52

0.55

0.63

1500

1395

80M

1.46

3.9

67.0

67.0

0.81

3.8

2.2

2.2

0.0014

47

0.55

0.63

1000

910

80M

1.60

3.4

67.0

66.5

0.74

5.8

2.1

2.2

0.0017

40

0.55

0.63

750

675

90L

1.58

3.0

66.0

65.0

0.76

7.8

1.7

1.9

0.0031

41

0.75

0.86

3000

2854

80M

1.73

5.6

73.0

72.0

0.86

2.5

2.3

2.4

0.00079

56

0.75

0.86

1500

1395

80M

1.91

4.2

72.0

72.0

0.80

5.1

2.3

2.3

0.0017

47

0.75

0.86

1000

915

90S

2.05

3.7

69.0

69.0

0.76

7.8

2.2

2.2

0.0024

43

0.75

0.86

750

679

100L

2.15

3.0

66.0

65.0

0.76

11.0

1.6

1.9

0.0051

45

1.1

1.3

3000

2845

80M

2.40

6.1

77.0

77.0

0.87

3.7

2.6

2.7

0.001

56

✔

1.1

1.3

1500

1414

90S

2.55

4.6

77.0

77.0

0.81

7.4

2.3

2.4

0.0024

48

✔

1.1

1.3

1000

915

90L

2.85

3.8

72.0

72.0

0.77

11.0

2.3

2.3

0.0033

43

1.1

1.30

750

679

100L

2.90

3.3

72.0

72.0

0.76

15.0

1.8

2.1

0.0063

45

1.5

1.75

3000

2860

90S

3.25

5.5

79.0

80.0

0.85

5.0

2.4

2.7

0.0014

60

✔

1.5

1.75

1500

1420

90L

3.40

5.3

79.0

79.0

0.81

10.0

2.4

2.6

0.0033

48

✔

1.5

1.75

1000

925

100L

3.90

4.0

74.0

74.0

0.75

15.0

2.3

2.3

0.0047

47

1.5

1.75

750

705

112M

3.85

3.7

74.0

74.0

0.76

20.0

1.8

2.1

0.013

49

2.2

2.55

3000

2880

90L

4.55

6.3

82.0

82.0

0.85

7.3

2.8

3.1

0.0018

60

✔

2.2

2.55

1500

1420

100L

4.70

5.6

82.0

82.5

0.82

15.0

2.5

2.8

0.0047

53

✔

2.2

2.55

1000

940

112M

5.20

4.6

78.0

78.5

0.78

22.0

2.2

2.5

0.0091

52

2.2

2.55

750

700

132S

5.70

3.9

75.0

75.0

0.74

30.0

1.9

2.3

0.014

53

3

3.45

3000

2890

100L

6.10

6.8

84.0

84.0

0.85

9.9

2.8

3.0

0.0035

62

✔

3

3.45

1500

1420

100L

6.40

5.6

83.0

83.5

0.82

20.0

2.7

3.0

0.0055

53

✔

3

3.45

1000

949

132S

7.20

4.2

79.0

79.5

0.76

30.0

1.9

2.2

0.015

63

3

3.45

750

700

132M

7.60

4.1

77.0

77.5

0.74

41.0

2.1

2.4

0.019

53

65

22

42

3.7

41.5

520

Factory Test Certificate acc. to 3.1 EN 10 204

B02

0.00027

0.26

58.0

52

52

1.9

56M

45.0

433

52

1.9

2830

2.6

347 390

-

0.4

3000

2.0

288

31

0.77

0.11

0.29

249

-

55.0

0.44

191 221

31

56.0

56M

-

-

2.6

63M

-

31

0.20

850

-

-

56M

1350

31

3/4

1350

1000

-

4/4

1500 1500

-

31

Frame

0.07

0.11

-

-

F.L.

0.06

0.11

160

31

4/4

50Hz Full Locked Break J Lpf CEMEP Load Rotor Down [Kgm2] [dB(A)] Eff2

0.09

132

-

Locked Rotor

0.09

112

31

50Hz 60Hz Synch.

Full Load

Torque [Nm]

Standard

65

100

Regreasing device

50Hz

65

52

90

Auxiliary nameplate (clear text is required)

Power Factor

50Hz

52

80

Y82

Efficiency

50Hz

325 360 433

71

K40

200

Current [A]

0.09

List Price Adder ($) Frame Size 180

RPM 50Hz

225

22

250

22

280

315 -

-

Standard 65 22

83 22

IEC MOTORS Dimensions

1MJ6 Frames 71-200 Frame Size

KW

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

List Price Adder ($) Frame Size

Frame Size

400Volts, 50Hz - 40ºC Ambient

1LG6 Frames 180-315

Prices and data subject to change without notice.

12-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS Special Options

IEC MOTORS Special Options

1LA6 / 1LA7 / 1LA9 Frames 56-160

IMPROVED EFFICIENCY (eff2)

IEC MOTORS Delivery Time

Others

13-1

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

1LA7 Aluminum Frame

1LA6 Cast Iron Frame

IMPROVED EFFICIENCY (eff2)

IEC MOTORS Typical Performance

RPM

Current [A]

Efficiency

Power Factor

Torque [Nm]

50Hz

50Hz

50Hz

50Hz

50Hz

RPM

Current [A]

Efficiency

Power Factor

50Hz

50Hz

50Hz

50Hz

Torque [Nm] 50Hz

F.L.

Frame

Full Load

4/4

3/4

4/4

Full Locked Break J Lpf CEMEP Load Rotor Down [Kgm2] [dB(A)] Eff2

50Hz 60Hz Synch.

F.L.

Frame

4/4

3/4

4

4.6

3000

2905

112M

7.80

7.2

86.0

86.0

0.86

13.0

2.6

2.9

0.0059

63

✔

0.75

0.86

750

679

100L

2.15

3.0

66.0

65.0

0.76

11.0

1.6

1.9

0.0051

45

4

4.6

1500

1440

112M

8.20

6.0

85.0

85.5

0.83

27.0

2.7

3.0

0.012

53

✔

1.1

1.30

750

679

100L

2.90

3.3

72.0

72.0

0.76

15.0

1.8

2.1

0.0063

45

4

4.6

1000

949

132M

9.40

4.5

80.5

80.5

0.76

40.0

2.1

2.4

0.019

63

1.5

1.75

1000

925

100L

3.90

4.0

74.0

74.0

0.75

15.0

2.3

2.3

0.0047

47

4

4.6

750

715

160M

10.00

4.5

80.0

80.0

0.72

53.0

2.2

2.6

0.036

63

1.5

1.75

750

705

112M

3.85

3.7

74.0

74.0

0.76

20.0

1.8

2.1

0.013

49

50Hz 60Hz Synch.

Locked Rotor

KW

Full Load

Locked Rotor

4/4

Full Locked Break J Lpf CEMEP Load Rotor Down [Kgm2] [dB(A)] Eff2

5.5

6.3

3000

2925

132S

10.40

5.9

86.5

86.5

0.89

18.0

2.0

2.8

0.015

68

✔

2.2

2.55

1500

1420

100L

4.70

5.6

82.0

82.5

0.82

15.0

2.5

2.8

0.0047

53

5.5

6.3

1500

1455

132S

11.40

6.3

86.0

86.0

0.81

36.0

2.5

3.1

0.018

62

✔

2.2

2.55

1000

940

112M

5.20

4.6

78.0

78.5

0.78

22.0

2.2

2.5

0.0091

52 53

✔

6.3

1000

949

132M

12.60

5.0

83.0

83.0

0.76

55.0

2.3

2.6

0.025

63

2.2

2.55

750

700

132S

5.70

3.9

75.0

75.0

0.74

30.0

1.9

2.3

0.014

6.3

750

709

160M

13.00

4.7

83.5

83.5

0.73

74.0

2.3

2.7

0.046

63

3

3.45

3000

2890

100L

6.10

6.8

84.0

84.0

0.85

9.9

2.8

3.0

0.0035

62

✔

7.5

8.6

3000

2930

132S

13.80

6.9

88.0

88.0

0.89

24.0

2.3

3.0

0.019

68

✔

3

3.45

1500

1420

100L

6.40

5.6

83.0

83.5

0.82

20.0

2.7

3.0

0.0055

53

✔

7.5

8.6

1500

1455

132M

15.20

6.7

87.0

87.5

0.82

49.0

2.7

3.2

0.023

62

✔

3

3.45

1000

949

132S

7.20

4.2

79.0

79.5

0.76

30.0

1.9

2.2

0.015

63

7.5

8.6

1000

960

160M

17.00

4.6

86.0

86.0

0.74

75.0

2.1

2.5

0.044

66

3

3.45

750

700

132M

7.60

4.1

77.0

77.5

0.74

41.0

2.1

2.4

0.019

53

7.5

8.6

750

715

160L

17.60

5.3

85.5

85.5

0.72

100.0

2.7

2.7

0.064

63

4

4.6

3000

2905

112M

7.80

7.2

86.0

86.0

0.86

13.0

2.6

2.9

0.0059

63

✔

11

12.6

3000

2930

160M

20.00

6.5

89.5

89.5

0.88

36.0

2.1

2.9

0.034

70

✔

4

4.6

1500

1440

112M

8.20

6.0

85.0

85.5

0.83

27.0

2.7

3.0

0.012

53

✔

11

12.6

1500

1459

160M

21.50

6.2

88.5

89.0

0.84

72.0

2.2

2.7

0.043

66

✔

4

4.6

1000

949

132M

9.40

4.5

80.5

80.5

0.76

40.0

2.1

2.4

0.019

63

11

12.6

1000

960

160L

24.50

4.8

87.5

87.5

0.74

109.0

2.3

2.6

0.063

66

4

4.6

750

715

160M

10.00

4.5

80.0

80.0

0.72

53.0

2.2

2.6

0.036

63

15

17.3

3000

2940

160M

26.50

6.6

90.0

90.2

0.90

49.0

2.2

3.0

0.043

70

✔

5.5

6.3

3000

2925

132S

10.40

5.9

86.5

86.5

0.89

18.0

2.0

2.8

0.015

68

✔

15

17.3

1500

1459

160L

28.50

6.5

90.0

90.2

0.84

98.0

2.6

3.0

0.055

66

✔

5.5

6.3

1500

1455

132S

11.40

6.3

86.0

86.0

0.81

36.0

2.5

3.1

0.018

62

✔

18.5

21.3

3000

2940

160L

32.00

7.0

91.0

91.2

0.91

60.0

2.4

3.1

0.051

70

✔

5.5

6.3

1000

949

132M

12.60

5.0

83.0

83.0

0.76

55.0

2.3

2.6

0.025

63

5.5

6.3

750

709

160M

13.00

4.7

83.5

83.5

0.73

74.0

2.3

2.7

0.046

63

7.5

8.6

3000

2929

132S

13.80

6.9

88.0

88.0

0.89

24.0

2.3

3.0

0.019

68

✔

7.5

8.6

1500

1455

132M

15.20

6.7

87.0

87.5

0.82

49.0

2.7

3.2

0.023

62

✔

7.5

8.6

1000

960

160M

17.00

4.6

86.0

86.0

0.74

75.0

2.1

2.5

0.044

66

Prices and data subject to change without notice.

7.5

8.6

750

715

160L

17.60

5.3

85.5

85.5

0.72

100.0

2.7

3.0

0.064

63

11

12.6

3000

2940

160M

20.00

6.5

89.5

89.5

0.88

36.0

2.1

2.9

0.034

70

✔ ✔

11

12.6

1500

1459

160M

21.50

6.2

88.5

89.0

0.84

72.0

2.2

2.7

0.043

66

11

12.6

1000

960

160L

24.50

4.8

87.5

87.5

0.74

109.0

2.3

2.6

0.063

66

15

17.3

3000

2940

160M

26.50

6.6

90.0

90.2

0.90

49.0

2.2

3.0

0.043

70

✔

15

17.3

1500

1459

160L

28.50

6.5

90.0

90.2

0.84

98.0

2.6

3.0

0.055

66

✔

18.5

21.3

3000

2940

160L

32.00

7.0

91.0

91.2

0.91

60.0

2.4

3.1

0.051

70

✔

Prices and data subject to change without notice.

13-2

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

13-3

IEC MOTORS Dimensions

5.5 5.5

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

KW

400Volts, 50Hz - 40ºC Ambient IEC MOTORS Special Options

IEC MOTORS Special Options

400Volts, 50Hz - 40ºC Ambient

IMPROVED EFFICIENCY (eff2)

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

IEC MOTORS Delivery Time

1MJ6 - Cast Iron Frame

ATEX - Ex de IIC T4

IEC MOTORS Special Options IEC MOTORS Typical Performance

50Hz

50Hz

50Hz

F.L.

Frame

Full Load

Locked Rotor

4/4

Torque [Nm]

50Hz

50Hz

4/4

Full Load

Locked Rotor

KW Break Down

J Lpf [Kgm2] [dB(A)]

Terminal Box Mat.

RPM

Current [A]

Nominal Efficiency

Power Factor

50Hz

50Hz

50Hz

50Hz

50Hz 60Hz Synch.

F.L.

Frame

Full Load

Locked Rotor

4/4

4/4

Torque [Nm] 50Hz Full Load

Locked Rotor

Break Down

J Lpf [Kgm2] [dB(A)]

Terminal Box Mat.

0.29 1500

1325

71M

0.78

3.2

60.0

0.77

1.0

1.8

1.8

0.0006

44

Alum.

15

17.3

3000

2940

160M

26.50

6.6

89.0

0.91

49.0

2.2

3.1

0.04

70

0.25

0.29 1000

870

71M

0.82

3.1

63.0

0.70

2.0

2.2

2.2

0.0009

39

Alum.

15

17.3

1500

1455

160L

28.50

7.4

89.0

0.85

98.0

2.8

3.2

0.05

66

C.I.

0.37

0.43 3000

2750

71M

0.98

4.3

67.0

0.81

1.0

2.3

2.3

0.00035

52

Alum.

15

18.0

1000

970

180L

29.50

6.3

89.0

0.83

148.0

2.6

2.4

0.2

66

Alum.

0.37

0.43 1500

1375

71M

1.13

3.6

64.0

0.74

2.0

2.0

2.0

0.0008

44

Alum.

15

18.0

750

725

200L

32.00

5.0

87.5

0.78

198.0

2.1

2.2

0.37

58

Alum.

0.37

0.43 1000

910

80M

1.18

3.3

64.0

0.71

3.0

1.9

2.0

0.0015

40

Alum.

18.5

21.3

3000

2940

160L

32.50

7.0

91.0

0.91

60.0

2.4

3.3

0.05

70

C.I.

0.37

0.43

750

655

90L

1.16

2.8

61.0

0.76

5.0

1.4

1.7

0.0025

41

Alum.

18.5

21.3

1500

1460

180M

35.00

7.1

90.5

0.84

121.0

2.3

3.0

0.13

63

Alum.

0.55

0.63 3000

2790

71M

1.38

5.3

71.0

0.81

1.0

2.3

2.3

0.00045

52

Alum.

18.5

22.0

1000

975

200L

36.00

6.3

90.2

0.82

181.0

2.6

2.3

0.29

66

Alum.

0.55

0.63 1500

1395

80M

1.42

4.7

71.0

0.79

3.0

2.3

2.4

0.0015

47

Alum.

22

24.5

3000

2940

180M

39.00

6.9

92.0

0.88

71.0

2.5

3.2

0.07

70

Alum.

0.55

0.63 1000

900

80M

1.67

3.5

64.0

0.74

5.0

2.0

2.1

0.0018

40

Alum.

22

25.3

1500

1460

180L

41.00

7.1

91.2

0.85

144.0

2.3

3.0

0.15

63

Alum.

0.55

0.63

750

655

90L

1.62

2.9

65.0

0.76

7.0

1.5

1.7

0.0035

41

Alum.

22

26.5

1000

975

200L

42.50

5.7

90.8

0.83

215.0

2.5

2.3

0.33

66

Alum.

0.75

0.86 3000

2840

80M

1.75

6.3

72.0

0.86

2.0

2.4

2.3

0.00085

56

Alum.

30

33.5

3000

2940

200L

53.00

6.5

92.3

0.89

97.0

2.4

2.8

0.14

71

Alum.

0.75

0.86 1500

1395

80M

1.88

5.0

73.0

0.79

5.0

2.5

2.6

0.0018

47

Alum.

30

34.5

1500

1465

200L

55.00

7.4

91.8

0.86

196.0

2.6

3.2

0.24

65

Alum.

0.75

0.86 1000

910

90L

2.10

3.9

69.0

0.76

8.0

2.2

2.3

0.0028

43

Alum.

37

41.5

3000

2945

200L

64.00

7.7

92.8

0.90

120.0

2.4

2.8

0.16

71

Alum.

0.75

0.86

750

685

100L

2.30

3.5

65.0

0.72

10.0

1.6

1.8

0.0053

45

Alum.

1.1

1.3

3000

2835

80M

2.45

6.3

74.0

0.87

3.0

2.6

2.3

0.0011

56

Alum.

1.1

1.3

1500

1410

90L

2.70

4.9

73.0

0.80

7.0

2.1

2.5

0.0028

48

Alum.

1.1

1.3

1000

905

90L

2.95

4.3

72.0

0.75

12.0

2.4

2.4

0.0035

43

Alum.

1.1

1.3

750

685

100L

2.90

3.9

74.0

0.74

16.0

1.8

2.0

0.007

45

Alum.

1.5

1.75 3000

2850

90L

3.30

6.7

78.0

0.84

5.0

2.5

2.5

0.0015

60

Alum.

1.5

1.75 1500

1420

90L

3.50

5.8

77.0

0.80

10.0

2.2

2.6

0.0035

48

Alum.

1.5

1.75 1000

930

100L

4.00

4.5

75.0

0.73

15.0

2.3

2.5

0.0063

47

Alum.

1.5

1.75

750

700

112M

4.00

4.4

74.0

0.73

21.0

1.8

2.0

0.01

49

Alum.

2.2

2.55 3000

2860

90L

4.60

7.1

80.0

0.86

7.0

2.8

2.8

0.002

60

Alum.

2.2

2.55 1500

1420

100L

5.10

6.0

78.0

0.80

15.0

2.2

2.6

0.0048

53

Alum.

2.2

2.55 1000

945

112M

5.50

4.8

76.0

0.76

22.0

2.2

2.5

0.01

52

Alum.

2.2

2.55

750

695

132S

6.00

4.2

74.0

0.72

30.0

1.7

2.1

0.01

53

Alum.

3

3.45 3000

2885

100L

6.20

7.7

82.0

0.85

9.0

2.8

3.0

0.0038

62

Alum.

3

3.45 1500

1415

100L

6.60

6.4

80.0

0.82

20.0

2.7

3.0

0.0058

53

Alum.

3

3.45 1000

945

132S

7.40

4.8

78.0

0.75

30.0

2.0

2.2

0.01

63

Alum.

3

3.45

750

700

132M

7.90

4.4

76.0

0.72

40.0

1.9

2.2

0.01

53

Alum.

4

4.6

3000

2895

112M

7.80

7.6

84.0

0.88

13.0

2.4

2.8

0.0055

63

Alum.

4

4.6

1500

1435

112M

8.00

7.2

83.0

0.82

27.0

2.8

3.0

0.01

53

Alum.

4

4.6

1000

945

132M

9.60

5.0

79.0

0.76

40.0

2.0

2.4

0.01

63

Alum.

4

4.6

750

715

160M

9.90

4.8

81.0

0.72

54.0

2.1

2.3

0.03

63

Alum.

5.5

6.3

3000

2925

132S

10.50

5.9

85.0

0.89

18.0

2.0

2.6

0.01

68

Alum.

5.5

6.3

1500

1450

132S

11.10

6.9

86.0

0.83

36.0

2.4

3.3

0.01

62

Alum.

5.5

6.3

1000

950

132M

12.60

5.4

83.0

0.76

55.0

2.2

2.5

0.02

63

Alum.

5.5

6.3

750

710

160M

13.30

5.1

83.0

0.72

74.0

2.3

2.5

0.04

63

Alum.

7.5

8.6

3000

2930

132S

14.50

6.9

87.0

0.89

24.0

2.3

2.6

0.01

68

Alum.

7.5

8.6

1500

1450

132M

15.00

7.7

86.0

0.84

49.0

2.7

3.3

0.02

62

Alum.

7.5

8.6

1000

960

160M

17.50

5.1

86.0

0.72

75.0

2.1

2.5

0.04

66

Alum.

8.6

750

715

160L

17.90

5.8

84.0

0.72

100.0

2.6

2.8

0.06

63

C.I.

11

7.5

12.6

3000

2940

160M

20.50

6.5

88.0

0.88

36.0

2.1

2.6

0.03

70

Alum.

11

12.6

1500

1455

160M

21.50

6.6

87.0

0.85

72.0

2.4

2.9

0.04

66

Alum.

11

12.6

1000

960

160L

24.50

5.5

87.0

0.74

109.0

2.3

2.5

0.04

66

C.I.

11

13.2

750

725

180L

26.00

5.0

87.0

0.70

145.0

2.0

2.2

0.21

60

Alum.

Alum.

Prices and data subject to change without notice.

Prices and data subject to change without notice. 13-4

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

13-5

IEC MOTORS Dimensions

0.25

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

Current [A]

Power Factor

IEC MOTORS Special Options

RPM

Nominal Efficiency

50Hz 60Hz Synch.

ATEX - Ex de IIC T4

400Volts, 50Hz - 40ºC Ambient

400Volts, 50Hz - 40ºC Ambient

KW

1MJ6 - Cast Iron Frame

IEC MOTORS Delivery Time

Explosion Proof - TEFC IEC Motor

Explosion Proof - TEFC IEC Motor

IEC MOTORS Delivery Time

1MJ7 - Cast Iron Frame

General Purpose - TEFC IEC Motor ATEX - Ex de IIC T4

IEC MOTORS Typical Performance

400Volts, 50Hz - 40ºC

RPM

Current [A]

Nominal Efficiency

50Hz

50Hz

50Hz

50Hz

50Hz 60Hz Synch.

F.L.

Power Factor

Torque [Nm] 50Hz

Frame

Full Load

Locked Rotor

4/4

4/4

Full Load

Locked Rotor

Nominal RPM Break Down

J Lpf [Kgm2] [dB(A)]

Current [A]

Terminal Box Mat.

kW Synch.

F.L.

Full Frame Load

Locked Rotor

Efficiency

Power Factor

4/4

3/4

4/4

Torque [Nm] Full Load

Locked Rotor

Break J Down [Kgm2]

Lpf [dB(A)]

CEMEP eff1

18.5

22

750

725

225S

37.5

5.0

88.6

0.80

244

2.1

2.2

0.58

58

C.I.

0.06 1500

1380

56M

0.22

3.1

61.0

61.0

0.66

0.4

2.7

2.8

0.00027

42

22

26.5

750

725

225M

43.5

5.0

90.1

0.81

290

2.1

2.2

0.66

58

C.I.

0.09 3000

2830

56M

0.24

4.5

70.0

70.0

0.76

0.3

3.6

3.0

0.00015

41

30

36

900

978

225M

56

5.7

92.0

0.84

293

2.6

2.2

0.57

66

C.I.

0.09 1500

1390

56M

0.31

3.2

62.0

62.0

0.68

0.6

2.8

2.8

0.00035

42

30

36

750

730

250M

58

5.0

91.6

0.81

392

2.1

2.1

1.1

57

C.I.

0.12 3000

2830

56M

0.31

4.3

69.0

69.0

0.81

0.4

3.2

2.8

0.0002

41

37

42.5

1500

1475

225S

67

7.0

93.0

0.86

240

2.5

3.1

0.44

65

C.I.

0.12 1500

1395

63M

0.41

3.5

66.0

66.0

0.65

0.8

2.7

2.6

0.00037

42

37

44.5

900

980

250M

69

6.0

92.4

0.84

361

2.6

2.1

0.89

60

C.I.

0.18 3000

2839

63M

0.48

4.8

70.0

70.0

0.78

0.6

2.8

3.1

0.00022

49

37

44.5

750

732

280S

70

5.5

92.7

0.82

483

2.2

2.2

1.4

58

C.I.

0.18 1500

1395

63M

0.59

3.6

65.0

65.0

0.68

1.3

3.0

2.5

0.00045

42

45

51

3000

2955

225M

77

6.9

93.9

0.90

145

2.3

2.7

0.24

71

C.I.

0.25 3000

2840

63M

0.63

4.9

72.0

72.0

0.80

0.8

2.5

2.5

0.00026

49

45

52

1500

1475

225M

80

7.0

93.4

0.87

292

2.6

3.2

0.52

65

C.I.

0.25 1500

1410

71M

0.81

4.3

70.0

70.0

0.64

1.7

3.6

3.1

0.00076

44

45

54

900

982

280S

81

6.0

93.0

0.86

438

2.4

2.3

1.3

60

C.I.

0.37 3000

2839

71M

0.94

6.5

74.0

74.0

0.77

1.2

3.3

3.1

0.00041

52

45

54

750

734

280M

84

5.5

92.8

0.83

585

2.2

2.2

1.6

58

C.I.

0.37 1500

1384

71M

1.04

4.2

71.0

71.0

0.73

2.6

3.3

3.0

0.00095

44

55

62

3000

2965

250M

93

6.9

94.0

0.90

177

2.1

2.8

0.45

75

C.I.

0.55 3000

2835

71M

1.42

6.3

75.0

75.0

0.75

1.9

3.6

2.9

0.0005

52

55

63

1500

1480

250M

97

6.7

94.0

0.87

355

2.6

2.5

0.79

65

C.I.

0.55 1500

1410

80M

1.32

5.6

77.0

77.0

0.78

3.7

3.4

2.9

0.0017

47

55

66

900

984

280M

99

6.2

93.6

0.86

534

2.5

2.4

1.5

60

C.I.

0.75 3000

2869

80M

1.66

8.3

80.0

80.0

0.82

2.5

4.4

3.2

0.001

56

55

66

750

738

315S

104

6.0

93.1

0.82

712

2.2

2.4

2.3

62

C.I.

0.75 1500

1399

80M

1.78

5.8

81.0

81.0

0.75

5.1

4.0

3.5

0.0024

47

75

84

3000

2975

280S

128

7.0

94.7

0.90

241

1.9

2.7

0.79

77

C.I.

0.75 1000

925

90S

2.00

4.4

75.5

75.5

0.72

7.7

3.0

2.5

0.0033

43

75

86

1500

1485

280S

132

6.7

94.7

0.86

482

2.5

2.7

1.4

67

C.I.

1.1

3000

2860

80M

2.10

7.0

84.0

84.0

0.89

3.7

3.8

3.2

0.0013

56

✔

75

90

900

988

315S

136

6.2

93.8

0.85

725

2.4

2.5

2.4

63

C.I.

1.1

1500

1440

90S

2.45

6.4

84.0

84.0

0.77

7.3

3.1

3.2

0.0033

48

✔

75

90

750

738

315M

140

6.2

93.6

0.82

970

2.3

2.5

3

62

C.I.

1.1

1000

940

90L

2.75

5.7

82.0

82.0

0.70

11.0

3.7

3.2

0.005

43

90

101

3000

2975

280M

150

7.0

95.1

0.91

289

2.0

2.7

0.92

77

C.I.

1.5

3000

2890

90S

2.95

7.0

85.0

85.0

0.87

5.0

4.1

3.5

0.0018

60

✔

90

104

1500

1485

280M

160

6.8

95.0

0.86

579

2.5

2.8

1.6

67

C.I.

1.5

1500

1440

90L

3.30

6.7

85.0

85.0

0.77

9.9

3.6

3.4

0.004

48

✔

90

108

900

988

315M

162

6.2

94.2

0.85

870

2.4

2.5

2.9

63

C.I.

1.5

1000

949

100L

3.65

6.2

85.0

85.0

0.70

15.0

3.5

3.4

0.0065

47

110

123

3000

2980

315S

186

7.0

94.8

0.90

353

1.8

2.8

1.3

79

C.I.

2.2

3000

2890

90L

4.20

7.0

86.5

86.5

0.87

7.3

4.1

3.5

0.0022

60

✔

110

127

1500

1486

315S

194

6.7

94.8

0.86

707

2.5

2.7

2.2

69

C.I.

2.2

1500

1435

100L

4.50

7.0

86.5

86.5

0.82

15.0

3.4

3.6

0.0062

53

✔

132

148

3000

2980

315M

225

7.0

95.1

0.90

423

1.9

2.8

1.5

79

C.I.

2.2

1000

955 112M

5.40

6.2

84.0

84.0

0.70

22.0

2.9

3.0

0.014

52

132

152

1500

1486

315M

232

7.2

95.5

0.86

848

2.7

3.0

2.7

69

C.I.

3

3000

2890

100L

5.70

7.0

87.0

87.0

0.88

9.9

3.4

3.2

0.0044

62

✔

3

1500

1435

100L

6.10

7.0

87.5

87.7

0.81

20.0

3.8

3.9

0.0077

53

✔

4

3000

2905 112M

7.30

7.0

88.5

88.5

0.89

13.0

2.8

3.2

0.0077

63

✔

4

1500

1440 112M

8.10

6.9

88.5

89.0

0.81

27.0

3.2

3.2

0.014

53

✔

4

1000

949 132M

8.50

6.3

84.0

84.0

0.81

40.0

3.0

2.7

0.025

63

5.5

3000

2929

132S

9.90

7.0

89.5

89.5

0.90

18.0

2.7

3.2

0.019

68

✔

5.5

1500

1455

132S

10.60

7.0

89.5

89.5

0.84

36.0

3.2

3.6

0.023

62

✔

5.5

1000

960 132M

12.00

7.3

86.0

86.0

0.77

55.0

3.7

3.6

0.03

63

7.5

3000

2929

132S

13.00

7.0

90.5

90.5

0.92

24.0

2.8

3.1

0.024

68

✔

7.5

1500

1455 132M

14.20

7.0

90.3

90.5

0.84

49.0

3.4

3.6

0.029

62

✔

7.5

1000

964 160M

17.00

5.5

88.0

88.0

0.72

74.0

2.4

2.5

0.063

66

11

3000

2944 160M

19.40

7.0

91.0

91.0

0.90

36.0

2.5

3.1

0.044

70

✔

11

1500

1459 160M

20.50

6.9

91.5

92.0

0.85

72.0

2.6

3.2

0.055

66

✔

11

1000

23.00

6.9

88.5

88.5

0.78

109.0

3.1

3.2

0.0072

66

15

3000

2944 160M

26.50

7.0

91.5

91.5

0.90

49.0

2.5

3.1

0.051

70

✔

15

1500

1459

160L

27.50

7.0

92.0

92.3

0.86

98.0

2.8

3.3

0.072

66

✔

18.5

3000

2940

160L

31.50

7.0

92.3

92.5

0.92

60.0

2.4

3.1

0.065

70

✔

960

160L

IEC MOTORS Dimensions

Prices and data subject to change without notice.

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

KW

HIGH EFFICIENCY (eff1)

Prices and data subject to change without notice.

13-6

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

IEC MOTORS Special Options

IEC MOTORS Special Options

400Volts. 50Hz - 40ºC Ambient

1LA9 Aluminum Frame

IEC MOTORS Delivery Time

Explosion Proof - TEFC IEC Motor

13-7

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

1LA9 Aluminum Frame

1LG6 Cast Iron

HIGH EFFICIENCY (eff1)

400Volts 50Hz - 40ºC Ambient Nominal

HP

Synch.

F.L.

0.08

1800

1715 3440

Full Frame Load

Locked Rotor

4/4

4/4

Full Load

Locked Rotor

Break Down

56M 56M

0.18

3.4

63.0

0.65

0.3

2.7

3.0

0.23

5.5

70.0

0.74

RPM

Torque [Nm]

0.3

3.6

3.8

Current [A] Full Frame Load

J Lpf EPAct [Kgm2] [dB(A)] Nr. CC032A

kW

0.00027

46

11

750

725

180L

23.5

45

15

1000

975

180L

29.5

750

725

200L

30.5

0.00015

RPM

F.L.

Locked Rotor

Efficiency

Cos

4/4

3/4

4/4

4.6

88.7

89.6

0.76

5.5

90.9

91.7

0.81

5.3

89.3

89.8

0.8

Torque [Nm] Full Load

Locked Rotor

Break Down

J Lpf [Kgm2] [dB(A)]

145

1.7

2.2

0.21

147

2.4

2.5

0.2

52

198

2.3

2.6

0.37

62

CEMEP eff1

62

0.12 1800

1725

56M

0.29

3.5

64.0

0.60

0.5

2.8

3.0

0.00035

46

15

0.16 3600

3440

56M

0.28

5.4

71.0

0.76

0.3

3.2

3.4

0.0002

45

18.5

1500

0.16 1800

1710

63M

0.37

3.9

68.0

0.60

0.7

2.7

2.8

0.00037

46

18.5

1000

0.25 3600

3440

63M

0.40

4.9

71.0

0.79

0.5

2.8

3.3

0.00022

53

18.5

0.25 1800

1705

63M

0.54

3.6

66.0

0.63

1.1

3.0

3.1

0.00045

46

22

3000

2955 180M

0.33 3600

3460

63M

0.56

5.0

72.0

0.76

0.7

2.5

2.7

0.00026

53

22

1500

1470

0.33 1800

1730

71M

0.76

4.9

69.0

0.60

1.4

3.6

3.4

0.00076

48

22

1000

978

0.5

3600

3445

71M

0.86

7.5

72.0

0.75

1.0

3.3

3.4

0.00041

56

22

750

0.5

1800

1725

71M

0.98

4.9

70.0

0.68

2.1

3.3

3.4

0.00095

48

30

3000

2960

200L

0.75 3600

3445

71M

1.30

7.2

73.0

0.73

1.6

3.4

3.7

0.0005

56

30

1500

1470

200L

0.75 1800

1725

80M

1.24

6.8

75.5

0.74

3.1

3.4

3.6

0.0017

51

30

1000

980 225M

1

3600

3485

80M

1.52

9.6

75.5

0.82

2.0

4.4

4.4

0.001

60

✔

30

750

57

6

92.8

93.3

0.82

390

2.5

2.8

1.1

53

1

1800

1720

80M

1.59

7.3

82.5

0.75

4.1

4.0

3.9

0.0024

51

✔

37

3000

2960

200L

64

7.2

94.1

94

0.89

119

2.5

3.3

0.18

71

✔

47

✔

37

1500

1480

225S

67

6.8

94

94.4

0.85

239

2.7

3 0.

4

60

✔

1000

985 250M

69

6.8

93.7

94.1

0.83

359

2.9

2.5

0.93

57

1

1200

1140

90S

1.78

5.6

80.0

0.66

6.2

3.0

3.0

0.0033

750

1470 180M

✔

34.5

6.4

92.6

93.2

0.83

120

2.5

3

0.12

60

978

200L

36

5.6

91.2

91.8

0.81

181

2.4

2.4

0.29

59

730

225S

36

5.6

91.1

91.8

0.81

242

2.3

2.6

0.55

54

38.5

7.2

94.1

94.5

0.88

71

2.5

3.4

0.086

67

✔

180L

40.5

6.7

93.2

93.5

0.84

143

2.5

3.1

0.14

60

✔

200L

42

5.6

91.9

92.5

0.82

215

2.4

2.4

0.36

56

43

5.8

91.6

92.1

0.81

288

2.4

2.8

0.66

58

53

7

93.5

93.4

0.88

97

2.4

3.3

0.15

71

✔

55

6.7

93.3

93.4

0.85

195

2.6

3.3

0.23

62

✔

56

6.5

93.2

93.7

0.83

292

2.8

2.9

0.63

54

730 225M

735 250M

1.5

3600

3480

80M

1.90

8.6

82.5

0.88

3.1

3.8

3.2

0.0013

60

✔

37

1.5

1800

1755

90S

2.15

7.7

84.0

0.76

6.1

3.1

3.9

0.0033

52

✔

37

750

280S

71

5.7

93.1

93.3

0.81

479

2.3

2.3

1.4

58

2

1200

1150

90L

2.55

6.4

85.5

0.64

9.3

3.7

3.7

0.005

47

✔

45

3000

2965 225M

77

7.3

94.9

95.1

0.89

145

2.5

3.2

0.27

71

✔

2

3600

3510

90S

2.60

8.6

84.0

0.86

4.1

4.1

4.1

0.0018

64

✔

45

1500

1480 225M

81

6.9

94.5

94.7

0.85

290

2.8

3

0.49

60

✔

2

1800

1775

90L

2.95

8.1

84.0

0.76

14.0

3.6

4.2

0.004

52

✔

45

1000

81

6.8

94.4

94.6

0.85

435

3

2.7

1.4

58

2

1200

1160

100L

3.20

7.2

86.5

0.68

12.0

3.5

3.8

0.0065

51

3

3600

3510

90L

3.80

8.5

85.5

0.85

6.1

4.1

5.1

0.0022

64

3

1800

1750

100L

4.00

8.4

87.5

0.79

12.0

3.4

4.3

0.0062

57

3

1200

1160 112M

4.80

7.5

87.5

0.66

18.0

2.9

3.7

0.014

56

4

3600

3510

100L

5.00

8.6

86.5

0.87

8.1

3.4

3.7

0.0044

66

55

750

740

4

1800

1750

100L

5.50

8.7

87.5

0.79

16.0

3.8

4.6

0.0077

57

75

3000

2975

5

3600

3540 112M

6.00

9.2

87.5

0.88

10.0

2.8

4.0

0.0077

67

✔

75

1500

5

1800

1755 112M

6.70

8.6

87.5

0.79

20.0

3.2

3.9

0.014

57

✔

75

1000

5

1200

1160 132M

6.90

7.9

87.5

0.77

31.0

3.0

3.6

0.025

67

✔

75

750

740 315M

138

6.7

94.5

94.7

0.83

968

2.5

2.9

3.1

58

72

✔

90

3000

2978 280M

150

7.6

95.6

95.7

0.9

289

2.6

3.1

1

73

✔

1500

1486 280M

158

7.5

95.4

95.5

0.86

578

2.7

3.1

1.7

67

✔

7.5

3600

3540

132S

8.70

8.5

88.5

0.90

15.0

2.7

3.8

0.019

✔ ✔

738

988

280S

45

750

738 280M

86

6.1

93.7

94

0.81

582

2.6

2.5

1.6

58

55

3000

2975 250M

93

6.8

95.3

95.3

0.9

177

2.4

3

0.47

71

✔

55

1500

1485 250M

96

7.5

95.1

95.3

0.87

354

2.6

3

0.86

61

✔

55

1000

988 280M

99

7.3

94.6

94.8

0.85

532

3.3

2.9

1.6

58

315S

102

6.3

94.3

94.4

0.82

710

2.5

2.9

2.5

58

280S

128

7

95.2

95.2

0.89

241

2.5

3

0.83

73

✔

1485

280S

130

6.8

95.1

95.2

0.87

482

2.5

2.9

1.4

67

✔

990

315S

138

7.3

95

95

0.83

723

2.8

3

2.5

61

7.5

1800

1760

132S

9.50

8.7

89.5

0.81

30.0

3.2

4.1

0.023

66

✔

90

7.5

1200

1160 132M

10.60

8.4

89.5

0.73

46.0

3.7

4.3

0.03

67

✔

90

1000

990 315M

160

7.3

95.3

95.4

0.85

868

2.7

2.9

3.2

61

3600

3540

11.40

8.3

89.5

0.92

20.0

2.8

3.7

0.024

72

✔

90

750

740

315L

164

6.3

94.7

95.1

0.84

1161

2.4

2.8

3.9

57 76

10

132S

10

1800

1760 132M

12.80

8.7

89.5

0.82

40.0

3.4

4.1

0.029

66

✔

110

3000

2982

315S

182

6.9

95.8

95.7

0.91

352

2.4

2.8

1.4

10

1200

1165 160M

15.00

6.4

89.5

0.70

61.0

2.4

2.8

0.063

70

✔

110

1500

1488

315S

190

7.1

95.9

96

0.87

706

2.7

2.9

2.3

65

15

3600

3555 160M

17.00

8.5

90.2

0.90

30.0

2.5

3.7

0.044

74

✔

110

1000

990

315L

196

7.4

95.6

95.7

0.85

1061

2.9

2.9

4

61

15

1800

1765 160M

17.90

8.1

91.0

0.85

61.0

2.6

3.2

0.055

70

✔

110

750

740

315L

200

6.4

94.8

95.1

0.84

1420

2.4

2.6

4.5

57

15

1200

1165

160L

19.00

8.3

90.2

0.77

92.0

3.1

3.8

0.0072

70

✔

132

3000

2982 315M

220

7.1

96

95.9

0.91

423

2.6

2.9

1.6

76

20

3600

3555 160M

23.20

8.5

90.2

0.90

40.0

2.5

3.7

0.051

74

✔

132

1500

1488 315M

225

7.3

96.1

96.2

0.88

847

2.7

2.9

2.9

64

20

1800

1765

160L

24.50

8.5

91.0

0.85

81.0

2.8

3.5

0.072

70

✔

132

1000

25

3600

3550

160L

27.70

8.5

91.0

0.92

50.0

2.4

3.5

0.065

74

✔

132 160 160

Prices and data subject to change without notice.

13-8

2007 Low Voltage AC Motors Selection and Pricing Guide

990

315L

235

7.8

95.8

95.8

0.85

1273

3.1

3.1

4.7

61

750

740

315L

240

6.7

94.9

95.2

0.84

1704

2.5

2.9

5.3

58

3000

2982

315L

260

7.1

96.4

96.4

0.92

512

2.5

2.9

2.1

76

1500

1490

315L

275

7.4

96.3

96.4

0.88

1026

3

3

3.5

64

160

1000

990

315L

280

7.8

95.8

95.9

0.86

1543

3.2

3.1

5.4

64

200

3000

2982

315L

320

6.9

96.5

96.5

0.93

641

2.5

2.8

2.5

76

200

1500

1490

315L

340

7.6

96.4

96.5

0.88

1282

3.2

3

4.2

64

Prices and data subject to change without notice.

2007 Low Voltage AC Motors Selection and Pricing Guide

13-9

IEC MOTORS Dimensions

IEC MOTORS Dimensions

Power Factor

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

0.12 3600

Efficiency

Current [A]

IEC MOTORS Special Options

IEC MOTORS Special Options

460Volts, 60Hz - 40ºC RPM

HIGH EFFICIENCY (eff1)

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

1LG6 Cast Iron

1LA7 Horizontal, Foot Mounted

HIGH EFFICIENCY (eff1)

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

IEC MOTORS Typical Performance

Current [A]

Cos

Torque [Nm]

4/4

4/4

Full Load

Locked Rotor

Break Down

J [Kgm2]

RPM

F.L.

Frame

Full Load

Lpf EPAct [dB(A)] Nr. CC032A

20

1200

1178

180L

25.5

6.5

91

0.8

121

2.9

3

0.2

57

✔

25

1800

1775 180M

31

7.1

92.4

0.82

100

2.9

3.3

0.12

65

✔

25

1200

1180

32.5

6.5

91.7

0.79

151

2.9

2.7

0.29

65

✔

30

3600

3560 180M

34

7.9

93

0.88

60

2.7

3.7

0.086

72

✔

30

1800

1775

180L

36.5

7.4

92.4

0.83

120

2.8

3.4

0.14

65

✔

30

1200

1180

200L

38.5

6.4

91.7

0.8

181

2.9

2.7

0.36

65

✔

40

3600

3565

200L

46

7.8

91.7

0.88

80

2.7

3.7

0.15

75

✔

40

1800

1775

200L

48

7.7

93

0.84

160

3

3.7

0.23

66

✔

40

1200

1184 225M

49

7.2

93

0.82

241

3.4

3.4

0.63

62

✔

50

3600

3565

200L

57

7.8

92.4

0.89

100

2.8

3.7

0.18

75

✔

50

1800

1785

225S

60

7.5

93.6

0.84

199

3.1

3.4

0.4

65

50

1200

1184 225M

61

7.6

93

0.83

301

3.2

3.4

0.76

61

50

1200

1186 250M

61

7.4

93

0.82

300

3.4

2.9

0.93

63

60

3600

3570 225M

67

8.3

93.6

0.89

120

2.8

3.6

0.27

74

✔

60

1800

1785 225M

70

7.9

94.1

0.85

239

3.3

3.5

0.49

65

✔

60

1200

1186 250M

73

7.4

93.6

0.82

361

3.4

2.9

1.07

65

✔

60

1200

1190

280S

72

7.7

94.1

0.83

359

3.6

3.1

1.4

62

75

3600

3570 225M

83

8.7

94.5

0.9

150

3.3

3.7

0.32

74

75

3600

3578 250M

84

7.5

93.6

0.89

149

2.7

3.2

0.47

75

75

1800

1785 225M

88

7.8

94.1

0.85

299

3

3.3

0.66

64

75

1800

1790 250M

86

8.2

94.5

0.86

298

2.9

3.4

0.86

68

75

1200

1190 280M

89

8.3

94.5

0.83

449

3.9

3.3

1.6

62

100

3600

3580 250M 112

8.4

94.1

0.89

199

2.8

3.5

0.57

79

100

3600

3580

7.9

95

0.89

199

2.8

3.4

0.83

77

100

1800

1788 250M 116

8.1

94.5

0.86

398

3

3.3

0.99

72

100

1800

1788

7.6

94.5

0.86

398

2.9

3.2

1.4

71

280S 110 280S 114

IEC MOTORS Dimensions

HP

200L

Locked Rotor

Efficiency

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

RPM

IEC MOTORS Special Options

IEC MOTORS Special Options

460Volts, 60Hz - 40ºC Ambient

✔

✔ ✔

✔ ✔

100

1200

1190 280M 118

8.4

94.5

0.84

599

4

3.3

1.94

64

✔

100

1200

1191

315S 120

8.4

94.5

0.82

598

3.3

3.4

2.5

66

✔

125

3600

3580 280M 136

8.3

95

0.9

249

2.9

3.4

1

77

✔

125

1800

1790 280M 144

8.2

95

0.86

497

3

3.4

1.7

71

✔

125

1200

1191 315M 148

7.9

95

0.84

747

3

3.1

3.2

66

✔

150

3600

3580 280M 164

8.5

95

0.9

299

3.1

3.6

1.16

77

✔

150

3600

3585

315S 164

7.5

94.5

0.91

298

2.6

3.1

1.4

81

✔

150

1800

1788 280M 172

8.4

95

0.86

598

3.1

3.5

1.88

71

✔

150

1800

1791

315S 170

7.8

95

0.87

596

3.1

3.2

2.3

75

✔

150

1200

1192

315L 176

8.5

95

0.84

896

3.3

3.3

4

66

✔

175

3600

3586 315M 190

8.3

95

0.91

348

3

3.3

1.6

81

✔

175

1800

1791 315M 198

8.4

95.4

0.87

696

3.2

3.3

2.9

75

✔

175

1200

1192

315L 205

8.9

95

0.84

1046

3.6

3.6

4.7

66

✔

200

3600

3588

315L 215

8.4

95.4

0.91

397

3

3.5

2.1

81

✔

200

1800

1792

315L 225

9

95.4

0.87

795

3.7

3.6

3.5

75

✔

200

1200

1192

315L 235

9.4

95.4

0.84

1195

4

4

5.4

69

✔

250

3600

3588

315L 265

8.6

95.4

0.93

496

3.2

3.4

2.5

81

250

1800

1792

315L 280

9.1

95.8

0.87

994

4

3.7

4.2

75

300

3600

3591

315L 320

10.0

95.4

0.92

595

4.1

3.9

2.74

83

300

1800

1792

315L 335

9.3

95.8

0.87

1193

4

3.7

4.5

81

Frame 56M 56M 63M 63M 71M 71M 80M 80M 90S 90L 100L 100L 112M 132S 132S 132M 132M 160M 160M 160L

Type Poles 1LA7 050 2,4 1LA7 053 2,4 1LA7 060 2,4 1LA7 063 2,4,6 1LA7 070 2,4,6,8 1LA7 073 2,4,6,8 1LA7 080 2,4,6,8 1LA7 083 2,4,6,8 1LA7 090 2,4,6,8 1LA7 096 2,4,6,8 1LA7 106 2,4,6,8 1LA7 107 4,8 1LA7 113 2,4,6,8 1LA7 130 2,4,6,8 1LA7 131 2 1LA7 133 4,6,8 1LA7 134 6 1LA7 163 2,4,6,8 1LA7 164 2,8 1LA7 166 2,4,6

A 90 90 100 100 112 112 125 125 140 140 160 160 190 216 216 216 216 254 254 254

AA 25 25 27 27 27 27 30.5 30.5 30.5 30.5 42 42 46 53 53 53 53 60 60 60

AB 110 110 120 120 132 132 150 150 165 165 196 196 226 256 256 256 256 300 300 300

AC 116 116 124 124 145 145 163 163 180 180 203 203 227 267 267 267 267 320 320 320

AD 101 101 101 101 111 111 120 120 128 128 135 135 148 167 167 167 167 197 197 197

AF 78 78 78 78 88 88 97 97 105 105 78 78 91 107 107 107 107 127 127 127

AG 74 74 74 74 74 74 75 75 75 75 120 120 120 140 140 140 140 165 165 165

B 71 71 80 80 90 90 100 100 100 125 140 140 140 140 140 178 178 210 210 254

BA 28 28 28 28 27 27 32 32 33* 33 47 47 47 49 49 49 49 57 57 57

BB 87 87 96 96 106 106 118 118 143 143 176 176 176 180 180 218 218 256 256 300

C 36 36 40 40 45 45 50 50 56 56 63 63 70 89 89 89 89 108 108 108

H 56 56 63 63 71 71 80 80 90 90 100 100 112 132 132 132 132 160 160 160

HA 6 6 7 7 7 7 8 8 10 10 12 12 12 15 15 15 15 18 18 18

K 5.8 5.8 7 7 7 7 905 905 10 10 12 12 12 12 12 12 12 14.5 14.5 14.5

K’ L LL 9 169 74 9 169 74 10 202.5 74 10 202.5 74 10 240 74 10 240 74 13.5 273.5 75 13.5 273.5 75 14 331 75 14 331 75 16 372 120 16 372 120 16 393 120 16 452.5 140 16 452.5 140 16 452.5 140 16 452.5 140 19 588 165 19 588 165 19 588 165

D 9 9 11 11 14 14 19 19 24 24 28 28 28 38 38 38 38 42 42 42

DB M3 M3 M4 M4 M5 M5 M6 M6 M8 M8 M10 M10 M10 M12 M12 M12 M12 M16 M16 M16

E 20 20 23 23 30 30 40 40 50 50 60 60 60 80 80 80 80 110 110 110

EB ED F 14 3 3 14 3 3 16 3.5 4 16 3.5 4 22 4 5 22 4 5 32 4 6 32 4 6 40 5 8 40 5 8 50 5 8 50 5 8 50 5 8 70 5 10 70 5 10 70 5 10 70 5 10 90 10 12 90 10 12 90 10 12

GA 10.2 10.2 12.5 12.5 16 16 21.5 21.5 27 27 31 31 31 41 41 41 41 45 45 45

*For NDE foot base, BA = 54 Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

Prices and data subject to change without notice. 13-10

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

14-1

IEC MOTORS Delivery Time

1LA6 Horizontal, Foot Mounted

1MJ6 / 1MJ7 Horizontal, Foot Mounted

IEC MOTORS Special Options

IEC MOTORS Special Options

General Purpose - TEFC IEC Motor

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

IEC MOTORS Dimensions Frame 100L 100L 112M 132S 132S 132M 132M 160M 160M 160L

Type 1LA6 106 1LA6 107 1LA6 113 1LA6 130 1LA6 131 1LA6 133 1LA6 134 1LA6 163 1LA6 164 1LA6 166

Poles 2,4,6,8 4,8 2,4,6,8 2,4,6,8 2 4,6,8 6 2,4,6,8 2,8 2,4,6

A 160 160 190 216 216 216 216 254 254 254

AA AB 40 196 40 196 42.5 226 50 256 50 256 50 256 50 256 60 300 60 300 60 300

AC 201 201 226 265 265 265 265 320 320 320

AD 164 164 178 194 194 194 194 226 226 226

AF 124 124 138 154 154 154 154 183 183 183

AG 121 121 121 141 141 141 141 166 166 166

B 140 140 140 140 140 178 178 210 210 254

BA 46 46 46 47 47 49 49 63 63 63

Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

14-2

2007 Low Voltage AC Motors Selection and Pricing Guide

BB 180 180 180 180 180 218 218 256 256 300

C 63 63 70 89 89 89 89 108 108 108

H 100 100 112 132 132 132 132 160 160 160

HA 12 12 15 17 17 17 17 18 18 18

K 12 12 12 12 12 12 12 15 14.5 14.5

K’ 16 16 16 16 16 16 16 18 18 18

L 372 372 393 453.5 453.5 453.5 453.5 588 588 588

LL 121 121 121 141 141 141 141 166 166 166

D 28 28 28 38 38 38 38 42 42 42

DB M10 M10 M10 M12 M12 M12 M12 M16 M16 M16

E 60 60 60 80 80 80 80 110 110 110

EB 50 50 50 70 70 70 70 90 90 90

ED 5 5 5 5 5 5 5 10 10 10

F GA 8 31 8 31 8 31 10 41 10 41 10 41 10 41 12 45 12 45 12 45

HA

K

K'

71M 1MJ6 070

Type

Poles 2,4

112 34 140 149 201 162 152 90 30

A

AA AB AC AD AF AG

B BA BA' BB

30 110 45 71

C

H

8

7

10

299 132 14 M5 30 22

L

LL

D

DB

E

EB ED 4

5

F

GA 16

71M 1MJ6 073

2,4,6

112 34 140 149 201 162 152 90 30

30 110 45 71

8

7

10

299 132 14 M5 30 22

4

5

16

80M 1MJ6 080

2,4,6

125 36 160 166 209 170 152 100 35

35 125 50 80 10 9.5 13.5 336 132 19 M6 40 32

4

6 21.5

80M 1MJ6 083

2,4,6

125 36 160 166 209 170 152 100 35

35 125 50 80 10 9.5 13.5 336 132 19 M6 40 32

4

6 21.5

90L 1MJ6 096

2,4,6,8

140 37 168 183 218 177 162 125 35

35 156 56 90 13 10 14

383 162 24 M8 50 40

5

8

27

90L 1MJ6 097

2,4,6,8

140 37 168 183 218 177 162 125 35

35 156 56 90 13 10 14

383 162 24 M8 50 40

5

8

27

100L 1MJ6 106

2,4,6,8

160 45 196 203 223 182 162 140 45

45 176 63 100 14 12 16

426 162 28 M10 60 50

5

8

31

100L 1MJ6 107

4,8

160 45 196 203 223 182 162 140 45

45 176 63 100 14 12 16

426 162 28 M10 60 50

5

8

31

112M 1MJ6 113

2,4,6,8

190 50 226 229 238 197 162 140 45

45 176 70 112 15 12 16

428 162 28 M10 60 50

5

8

31

132S 1MJ6 130

2,4,6,8

216 53 256 268 258 217 162 140 49

49 180 89 132 17 12 16

515 162 38 M12 80 70

5

10 41

132S 1MJ6 131

2

216 53 256 268 258 217 162 140 49

49 180 89 132 17 12 16

515 162 38 M12 80 70

5

10 41

132M 1MJ6 133

4,6,8

216 53 256 268 258 217 162 140 49 49 180 89 132 17 12 16

515 162 38 M12 80 70

5

10

132M 1MJ6 134

6

216 53 256 268 258 217 162 140 49

49 180 89 132 17 12 16

515 162 38 M12 80 70

5

10 41

160M 1MJ6 163

2,4,6,8

254 60 300 323 280 239 162 210 57

57 256 108 160 20 15 19

641 162 42 M16 110 90 10

12 45

160M 1MJ6 164

2,8

254 60 300 323 280 239 162 210 57

57 256 108 160 20 15 19

641 162 42 M16 110 90 10

12 45

160L 1MJ6 166

2,4,6,8

254 60 300 323 314 246 216 254 57

57 300 108 160 20 15 19

641 190 42 M16 110 90 10

12 45

180M 1MJ6 183

2,4

279 65 344 375 306 259 220 241 70 108 319 121 180 26 15 20

715 164 48 M16 110 100 5

14 51.5

180L 1MJ6 186

4,6,8

279 65 344 375 306 259 220 279 70 108 319 121 180 26 15 20

715 164 48 M16 110 100 5

14 51.5

200L 1MJ6 206

2

318 80 398 415 349 289 262 305 85

85 355 133 200 34 19 25 771.5 197 55 M20 110 100 5

16 59

200L 1MJ6 206

6

318 80 398 415 349 289 262 305 85

85 355 133 200 34 19 25 771.5 197 55 M20 110 100 5

16 59

200L 1MJ6 207

2

318 80 398 415 349 289 262 305 85

85 355 133 200 34 19 25 771.5 197 55 M20 110 100 5

16 59

200L 1MJ6 207

4,6,8

318 80 398 415 349 289 262 305 85

85 355 133 200 34 19 25 771.5 197 55 M20 110 100 5

16 59

41

225S 1MJ7 220

4,8

356 80 436 442 377 315 262 286 85 110 361 149 225 34 19 25

839 197 60 M20 140 125 10

225M 1MJ7 223

2

356 80 436 442 377 315 262 311 85 110 361 149 225 34 19 25

809 197 55 M20 110 100 5

18 64 16 59

225M 1MJ7 223

4,6,8

356 80 436 442 377 315 262 311 85 110 361 149 225 34 19 25

839 197 60 M20 140 125 10

18 64

250M 1MJ7 253

2

406 100 506 505 466 353 336 349 100 100 409 168 250 42 24 30

930 234 60 M20 140 125 10

18 64

250M 1MJ7 253

4,6,8

406 100 506 505 466 353 336 349 100 100 409 168 250 42 24 30

930 234 65 M20 140 125 10

18 69

280S 1MJ7 280

2

457 100 557 555 491 395 336 368 100 151 479 190 280 42 24 30 1010 234 65 M20 140 125 10

18 69

280S 1MJ7 280

4,6,8

457 100 557 555 491 395 336 368 100 151 479 190 280 42 24 30 1010 234 75 M20 140 125 10

20 75.5

280M 1MJ7 283

2

457 100 557 555 491 395 336 419 100 151 479 190 280 42 24 30 1010 234 65 M20 140 125 10

18 69

280M 1MJ7 283

4,6,8

457 100 557 555 491 395 336 419 100 151 479 190 280 42 24 30 1010 234 75 M20 140 125 10

20 79.5

315S 1MJ7 310

2

508 120 628 620 558 448 410 406 125 171 527 216 315 56 28 35 1114 266 65 M20 140 125 10

18 69 22 85

315S 1MJ7 310

4,6,8

508 120 628 620 558 448 410 406 125 171 527 216 315 56 28 35 1140 266 80 M20 170 140 10

315M 1MJ7 313

2

508 120 628 620 558 448 410 457 125 171 527 216 315 56 28 35 1114 266 65 M20 140 125 10

18 69

315M 1MJ7 313

4,6,8

508 120 628 620 558 448 410 457 125 171 527 216 315 56 28 35 1140 266 80 M20 170 140 10

22 85

Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

2007 Low Voltage AC Motors Selection and Pricing Guide

14-3

IEC MOTORS Dimensions

Frame

IEC MOTORS Delivery Time

1LA9 Horizontal, Foot Mounted

1LG6 Horizontal, Foot Mounted

Frame 56M 56M 63M 63M 71M 71M 80M 80M 90S 90L 90L 100L 100L 100L 112M 132S 132S 132M 132M 132M 160M 160M 160L

Frame 180M 180M 180L 200L 200L 200L 225S 225M 225M 225M 225M 250M 250M 250M 250M 250M 280 S 280 S 280M 280M 280M 280M 280M 315S 315S 315M 315M 315M 315L 315L 315L 315L 315L 315L 315L 315L 315L

IEC MOTORS Special Options

IEC MOTORS Special Options

General Purpose - TEFC IEC Motor

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

Poles 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2,4,6 2,4 6 2,4,6 2,6 4 2,4,6 2,4 2 6 4 6 2,4,6 2 2,4,6

A 90 90 100 100 112 112 125 125 140 140 140 160 160 160 190 216 216 216 216 216 254 254 254

AA 25 25 27 27 30.5 30.5 30.5 30.5 30.5 30.5 30.5 42 42 42 46 53 53 53 53 53 60 60 60

AB 110 110 120 120 132 132 150 150 165 165 165 196 196 196 226 256 256 256 256 256 300 300 300

AC 116 116 124 124 145 145 163 163 180 180 180 203 203 203 227 267 267 267 267 267 320 320 320

AD 101 101 101 101 111 111 120 120 128 128 128 135 135 135 148 167 167 167 167 167 197 197 197

AF 78 78 78 78 88 88 97 97 88 88 88 97 97 97 91 107 107 107 107 107 127 183 183

AG 74 74 74 74 74 74 75 75 75 75 75 120 120 120 120 140 140 140 140 140 165 165 165

B 71 71 80 80 90 90 100 100 100 125 125 140 140 140 140 140 140 178 178 178 210 210 254

BA 28 28 28 28 27 27 32 32 33 33 33 47 47 47 47 49 49 49 49 49 57 57 57

*For NDE foot base, BA = 54 Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

BB 87 87 96 96 106 106 118 118 143 143 143 176 176 176 176 180 180 218 218 218 256 256 300

C 36 36 40 40 45 45 50 50 56 56 56 63 63 63 70 89 89 89 89 89 108 108 108

H 56 56 63 63 71 71 80 80 90 90 90 100 100 100 112 132 132 132 132 132 160 160 160

HA 6 6 7 7 7 7 8 8 10 10 10 12 12 12 12 15 15 15 15 15 18 18 18

K K’ 5.8 9 5.8 9 7 10 7 10 7 10 7 10 905 13.5 905 13.5 10 14 10 14 10 14 12 16 12 16 12 16 12 16 12 16 12 16 12 16 12 16 12 16 14.5 19 14.5 19 14.5 19

L LL 169 74 195 74 202.5 74 228.5 74 240 74 240 74 273.5 75 308.5 75 331 75 358 75 376 75 407 120 407 120 442 120 431 120 452.5 140 490.5 140 452.5 140 490.5 140 490.5 140 588 165 588 165 628 165

D 9 9 11 11 14 14 19 19 24 24 24 28 28 28 28 38 38 38 38 38 42 42 42

DB M3 M3 M4 M4 M5 M5 M6 M6 M8 M8 M8 M10 M10 M10 M10 M12 M12 M12 M12 M12 M16 M16 M16

E 20 20 23 23 30 30 40 40 50 50 50 60 60 60 60 80 80 80 80 80 110 110 110

EB 14 14 16 16 22 22 32 32 40 40 40 50 50 50 50 70 70 70 70 70 90 90 90

ED 3 3 3.5 3.5 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 10 10 10

F 3 3 4 4 5 5 6 6 8 8 8 8 8 8 8 10 10 10 10 10 12 12 12

GA 10.2 10.2 12.5 12.5 16 16 21.5 21.5 27 27 27 31 31 31 31 41 41 41 41 41 45 45 45

Poles 2 4 4,6,8 2,6 2,6 4,8 4,8 2 4,6,8 2 4,6 2 4 6,8 2 4,6 2 4,6,8 2 4 6,8 2 4,6 2 4,6,8 8 2 4,6 2 4,6 8 2 4,6 8 2 4 6,8

A 279 279 279 318 318 318 356 356 356 356 356 406 406 406 406 406 457 457 457 457 457 457 457 508 508 508 508 508 508 508 508 508 508 508 508 508 508

AA 65 65 65 70 70 70 80 80 80 80 80 100 100 100 100 100 100 100 100 100 100 100 100 120 120 120 120 120 120 120 120 120 120 120 120 120 120

AB 339 339 339 378 378 378 436 436 436 436 436 490 490 490 490 490 540 540 540 540 540 540 540 610 610 610 610 610 610 610 610 610 610 610 610 610 610

AC 363 363 363 402 402 402 442 442 442 442 442 495 495 495 495 495 555 555 555 555 555 555 555 610 610 610 610 610 610 610 610 610 610 610 610 610 610

AD 262 262 262 300 300 300 325 325 325 325 325 392 392 392 392 392 432 432 432 432 432 432 432 500 500 500 500 500 500 500 500 500 500 500 651 651 500

AF 220 220 220 247 247 247 272 272 272 272 272 308 308 308 308 308 348 348 348 348 348 348 348 400 400 400 400 400 400 400 400 400 400 400 524 524 400

AG 152 152 152 260 260 260 260 260 260 260 260 300 300 300 300 300 300 300 300 300 300 300 300 380 380 380 380 380 380 380 380 380 380 380 470 470 380

B 241 241 279 305 305 305 286 311 311 311 311 349 349 349 349 349 368 368 419 419 419 419 419 406 406 457 457 457 508 508 508 508 508 508 508 508 508

BA 70 70 70 80 80 80 85 85 85 85 85 100 100 100 100 100 100 100 100 100 100 100 100 125 125 125 125 125 125 125 125 155 155 155 155 155 155

BA' 111 111 111 80 80 80 110 110 110 110 110 100 100 100 100 100 151 151 151 151 151 151 151 176 176 176 176 176 176 176 176 206 206 206 206 206 206

BB 328 328 328 355 355 355 361 361 361 361 361 409 409 409 409 409 479 479 479 479 479 479 479 527 527 527 578 578 578 578 578 648 648 578 648 648 648

C 121 121 121 133 133 133 149 149 149 149 149 168 168 168 168 168 190 190 190 190 190 190 190 216 216 216 216 216 216 216 216 216 216 216 216 216 216

H 180 180 180 200 200 200 225 225 225 225 225 250 250 250 250 250 280 280 280 280 280 280 280 315 315 315 315 315 315 315 315 315 315 315 315 315 315

HA 20 20 20 25 25 25 34 34 34 34 34 40 40 40 40 40 40 40 40 40 40 40 40 50 50 50 50 50 50 50 50 50 50 50 50 50 50

K 15 15 19 19 19 19 19 19 19 19 19 24 24 24 24 24 24 24 24 24 24 24 24 28 28 28 28 28 28 28 28 28 28 28 28 28 28

K' 19 19 25 25 25 25 25 25 25 25 25 30 30 30 30 30 30 30 30 30 30 30 30 35 35 35 35 35 35 35 35 35 35 35 35 35 35

L 720 669 720 720 777 720 789 819 849 869 899 887 957 887 957 957 960 960 1070 1070 960 1070 1070 1072 1102 1102 1232 1262 1232 1262 1262 1372 1402 1262 1373 1402 1402

LL 132 132 132 192 192 192 192 192 192 192 192 236 236 236 236 236 236 236 236 236 236 236 236 307 307 307 307 307 307 307 307 307 307 307 307 307 307

D 48 48 48 55 55 55 60 55 60 55 60 60 65 65 60 65 65 75 65 75 75 65 75 65 80 80 65 80 65 80 80 65 80 80 65 80 80

DB M16 M16 M16 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20 M20

E 110 110 110 110 110 110 110 140 110 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 170 170 140 170 140 170 170 140 170 170 140 170 170

EB 100 100 100 100 100 100 125 100 125 100 125 125 125 125 125 125 125 125 125 125 125 125 125 125 140 140 125 140 125 140 140 125 140 140 125 140 140

ED 5 5 5 5 5 5 10 5 10 5 10 10 10 10 10 10 10 10 10 10 10 10 10 10 25 25 10 25 10 25 25 10 25 25 10 25 25

F 14 14 14 16 16 16 18 16 18 16 18 18 18 18 18 18 18 20 18 20 20 18 20 18 22 22 18 22 18 22 22 18 22 22 18 22 22

GA 51.5 515 51.5 59 59 59 64 59 64 59 64 64 69 69 64 69 69 79.5 69 79.5 79.5 69 79.5 69 85 85 69 85 69 85 85 69 85 85 69 85 85

Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only. 14-4

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

14-5

IEC MOTORS Dimensions

IEC MOTORS Dimensions

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

Type 1LA9 050 1LA9 053 1LA9 060 1LA9 063 1LA9 070 1LA9 073 1LA9 080 1LA9 083 1LA9 090 1LA9 096 1LA9 096 1LA9 106 1LA9 107 1LA9 107 1LA9 113 1LA9 130 1LA9 131 1LA9 133 1LA9 133 1LA9 134 1LA9 163 1LA9 164 1LA9 166

Type 1LG6 183 1LG6 183 1LG6 186 1LG6 206 1LG6 207 1LG6 207 1LG6 220 1LG6 223 1LG6 223 1LG6 228 1LG6 228 1LG6 253 1LG6 253 1LG6 253 1LG6 258 1LG6 258 1LG6 280 1LG6 280 1LG6 283 1LG6 283 1LG6 283 1LG6 288 1LG6 288 1LG6 310 1LG6 310 1LG6 313 1LG6 313 1LG6 313 1LG6 316 1LG6 316 1LG6 316 1LG6 317 1LG6 317 1LG6 317 1LG6 318 1LG6 318 1LG6 318

IEC MOTORS Delivery Time

1LA6 / 1LA7 / 1LA9 / 1MJ6 B5-B14 Flange - without feet

1LG6 / 1MJ6 / 1MJ7 B5 Flange - without feet

IEC MOTORS Special Options

IEC MOTORS Special Options

General Purpose - TEFC IEC Motor

IEC MOTORS Delivery Time

General Purpose - TEFC IEC Motor

63 M

71 M

80 M

90 S, 90 L

100 L

112 M

132 S, 132 M

160 M, 160 L

Construction IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19 IM B5, IM B35, IM V1, IM V3 IM B14, IM B34, IM V18, IM V19 IM B14, IM B34, IM V18, IM V19

Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange Flange Standard flange Special flange

DIN EN 50347 DIN 42948 FF 100 A 120 FT 65 C 80 FT 85 C 105 FF 115 A 140 FT 75 C 90 FT 100 C 120 FF 130 A 160 FT 85 C 105 FT 115 C 140 FF 165 A 200 FT 100 C 120 FT 130 C 160 FF 165 A 200 FT 100 C 140 FT 130 C 160 FF 215 A 250 FT 130 C 160 FT 165 C 200 FF 215 A 250 FT 130 C 160 FT 165 C 200 FF 265 A 300 FT 165 C 200 FT 215 C 250 FF 300 A 350 FT 215 C 250 FT 265 C 300

LA 8 – – 8 – – 9 – – 10 – – 10 – – 11 – – 11 – – 12 – – 13 – –

LE 20 20 20 23 23 23 30 30 30 40 40 40 50 50 50 60 60 60 60 60 60 80 80 80 110 110 110

M 100 65 85 115 75 100 130 85 115 165 100 130 165 115 130 215 130 165 215 130 165 265 165 215 300 215 265

N 80 50 70 95 60 80 110 70 95 130 80 110 130 95 110 180 110 130 180 110 130 230 130 180 250 180 230

P 120 80 105 140 90 120 160 105 140 200 120 160 200 140 160 250 160 200 250 160 200 300 200 250 350 250 300

S 7 M5 M6 10 M5 M6 10 M6 M8 12 M6 M8 12 M8 M8 14.5 M8 M10 14.5 M8 M10 14.5 M10 M12 18.5 M12 M12

T 3 2.5 2.5 3 2.5 3 3.5 2.5 3 3.5 3 3.5 3.5 3 3.5 4 3.5 3.5 4 3.5 3.5 4 3.5 4 5 4 4

Z 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4

Frame 180M,180L 200L 225S,225M 2-pole 250M 280S,280M 315S,315M,315L 2-pole

Construction IMB5,IMV1,IMV3 IMB5 IMB5,IMV1,IMV3 IMB5,IMV1,IMV3 IMB5,IMV1,IMV3 IMB5,IMV1,IMV3 IMB5,IMV1,IMV3 IMB5,IMV1,IMV3

Flange Flange Flange Flange Flange Flange Flange Flange

DIN EN 50347 DIN 42948 FF300 A350 FF350 A400 FF400 A450 FF400 A450 FF500 A550 FF500 A550 FF600 A660 FF600 A660

LA 13 15 16 16 18 18 22 22

LE 110 110 140 110 140 140 170 140

M 300 350 400 400 500 500 600 600

N 250 300 350 350 450 450 550 550

P 350 400 450 450 550 550 660 660

S 18.5 18.5 18.5 18.5 18.5 18.5 24 24

T 5 5 5 5 5 5 6 6

Z 4 4 8 8 8 8 8 8

Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

1MJ6 B14 flange only up to frame size 90L 1MJ6 B14 special flange up to frame size 80M Prices and data are subject to change without notice. Dimensions are in millimeters. Dimensions are for reference only.

14-6

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

14-7

IEC MOTORS Dimensions

IEC MOTORS Dimensions

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

Frame 56 M

Notes

IEC MOTORS Special Options

IEC MOTORS Special Options

IEC MOTORS Delivery Time

IEC MOTORS Delivery Time

Notes

IEC MOTORS Typical Performance

IEC MOTORS Typical Performance

IEC MOTORS Dimensions

IEC MOTORS Dimensions

14-8

2007 Low Voltage AC Motors Selection and Pricing Guide

2007 Low Voltage AC Motors Selection and Pricing Guide

14-9

IEC MOTORS Dimensions

IEC MOTORS Typical Performance

IEC MOTORS Special Options

IEC MOTORS Delivery Time

Notes

14-10 2007 Low Voltage AC Motors Selection and Pricing Guide