TEST AND INSPECTION PER: 02-SAMSS-011, and Specifications As Noted Below. (1) VISUAL INSPECTION WITNESSING BY INSPECTOR (Note 1) (2) CERTIFICATES / RECORDS TO BE CHECKED BY INSPECTOR (3) CERTIFICATES / DATA TO BE PROVIDED BY VENDOR / SUPPLIER / MANUFACTURER
* *X * 0010
Pre-Fabrication/Production Requirements
Specification Details / Notes:
Steel Manufacture
02-SAMSS-011 Par. 5.1
0020
Forging Process
02-SAMSS-011 Par.5.2
Material Test Reports: of Cast or Heat Analysis, Product Product analysis
Per 02-SAMSS-011 Par. 5.4 and Table 5
0010
X
0030
X
and Carbon equivalent
0040
X
NDT Procedures and Personnel
Verify valid personnel qualification and approved procedure
* * *X 0010 X
In process inspection & test requirement
Specification Details / Notes:
Forging operation/process
One per PO line item
0012
X
Heat Treatment
02-SAMSS-011Par. 5.3 and Table-5
0020
X
0020
X
X
Mechanic Mechanical al Testing: Testing: Tensi Tensile le Test, Test, Impact Impact test test and Hardne Hardness ss test test
02-SAMSS02-SAMSS-011 011 Par.5.5 Par.5.5 and and Table Table 5.
0030
X
X
PMI requirement
Per SAES-A-206 and SA-175 form 320300.
Corrosion Tests
02-SAMSS-011 Par. 6 (For all Stainless Steel)
X
Metall Met allogr ograph aphic ic Examin Examinati ation: on: Grain Grain Size Size and and Ferrit Ferrite e Cont Content ent..
02-SAM 02-SAMSSSS-011 011 Par. Par. 7 and Table Table 5
X
Nondestructive Testing: Testing: a) Magnetic Particle Testing and and Liquid
02-SAMSS-011 Section 9. One per PO line item or 10% Per
penetrant Testing
line item which is higher.
0032
X
0034
X
0040
0042
X
X
X
Nondestructive Testing: b) Ultrasonic Testing
02-SAMSS-011 Par. 9.3. Refer to SAMSS for details and application of A707, A388, A508 requirements.
*** 0010 X
0030
Final inspection & test requirements
Specification Details / Notes:
Visual and Dimensional Inspection.
02-SAMSS-011, the respective ASTM/Industrial Standard and approved drawings.
IR022501
Continued...
INSPECTION & TESTING REQUIREMENTS
REVISION: 07/30/2012
CODE NUMBER:
SAUDI ARAMCO FORM-175
REPLACES: 07/15/2012
IR022501
PAGE:
2 of 2
(1) VISUAL INSPECTION WITNESSING BY INSPECTOR (Note 1) (2) CERTIFICATES / RECORDS TO BE CHECKED BY INSPECTOR (3) CERTIFICATES / DATA TO BE PROVIDED BY VENDOR / SUPPLIER / MANUFACTURER 0020
X
Inspection of Raised Fa Face Gasket Su Surface
02-SAMSS-011, ANSI B46.l: Su Surfaces shall have a fifinish of 3.2 to 6.4 micro-meters Ra
0030
X
Markings
02-SAMSS-011 Utilize respective ASTM & API standards.
0040
X
Protective Coating, End Covers & Packaging
02-SAMSS-011
0050
X
Special Flange Dimensions (when applicable)
02-SAMSS-011: Apply the Standar d Drawings as referenced in
X
SAMSS or the approved #Special Design#.
Notes: (1) May only be waived by the responsible Saudi Aramco, ASC, or AOC Inspection Offices. (2) See form SA 175 -000003 for instructions on using this form. (3) Extent of frequency of testing and inspection inspection is per 02-SAMSS-011 Table Table 3 and Table 4
