Zapper Circuit Schematics

21/06/2010

Zapper Circuit Schematics

Wizzers Workshop Personal Bioenergy Tools - Orgone Matrix Material Ergonite Orgonite Organite - Construction info & sales Radionics Stations -Mobius Coils - EM Pollution Control - DIY Plans & More!

70+ PAGES OF ORGONE AND RADIONICS DIY INFO, PRODUCTS & MORE. Home Products Site Map Gallery Info Links Contact

This site best viewed at 800 x 600 or higher resolution. This page widened to accommodate full size images.

Zapper Schematic Revisions and FREE zapper circuit schematics It has come to my attention that there was an error in the signal generator schematics which were prepared for the manual by Kevin Smith. Kevin has corrected the schematics, and below is the revision information. I will shortly send an updated copy to the distributor. We apologize for any inconvenience this may cause. In each of the circuits schematics, there is a short wire which connects pins 2 and 6. In the original schematics with the manual, this wire was erroneously portrayed as going to pin 7. Circuits built with the wire going going to pin 7 will not work. I t should go from pin 2 to pin 6, and the following graphics graphics indic ate this. Whether or not you have previously purchased a copy of How To Make An Orgone Field Pulser, are planning to purchase one, this is the correct information (for copies of the Pulser construction manual sold up to this time, Sep 17 2006. When I have uploaded a revised copy to the distributor, I will make mention of that fact on this page also. I have decided to make the material available freely, along with some excerpts from the supporting articles which Kevin supplied for the manual. Those of you who may not be interested in the OFP OFP construction construction manual, but ARE interested in 555-based signal generator circuits for use in zappers zappers,, blood electrification, driving mobius coils,, or for other electronics projects, please feel free to save this page for your own private use. Kevin says he is typing a little more text to put on this page as of coils Sep. 2006.- Jon Logan Graphics and edited text excerpts excerpts from Pulser construction construction manual reproduced below are copyrighted m aterial, m ade available free for private use only.

ZAPPER CIRCUIT SCHEMATICS by Kevin Smith (If you have questions about these circuits, please contact Kevin Smith at [email protected] [email protected])) Below is a single frequency signal generator that will drive the Pulser coil as required. However, the standard Pulser sold by Wizzer’s Workshop comes with a dual frequency driver circuit that I will describe further below. The frequency we will use for this example design will be 15 Hz. That is 15 pulses per second. So there are 7 or 8 high/on periods and 7 or 8 low/off periods. If you were working with an even numbered frequency then there would be equal on/off, high/low periods. (Refer to diagram above) The frequency output of the signal generator can be configured to just about any frequency from 0.0001 Hz up to a maximum of about 300 kHz or 300,000 Hz. The following schematic (1A) is the diagram for the single frequency signal generator generator ..

littlemountainsmudge.com/zapperrevi…

1/4

21/06/2010


A standard Pulser from Wizzer’s Workshop comes with a circuit that can run off a 9 volt battery and a wall adapter. The recommended adapter voltage rating that we tell users to use is 9 to 12 VDC and a current output rating of no less than 200 mA (9 VDC 300 mA recommended on the pulser labels). Now one minor problem I found with using two different voltages (ie. 9 volt battery and 12 volt adapter) is that the frequency will change slightly when using different voltages. The frequency tends to increase when the voltage goes up. So when tuning your frequency in you may want to tune it using the preferred power supply. If you use the device mainly in the home and always have access to a wall outlet then you would tune it using the adapter voltage and visa versa for portable 9 volt battery usage. Another addition that I have used involves two external transistor drivers to switch the current to the coil. The diagram 1b shows how to do this for a single source power supply. (ie. 9 volt battery or adapter) What this setup can do is it helps keep the IC output more stable frequency-wise especially when running the IC at max current. The IC’s frequency output will drift with temperature. As the ambient air and the chip heats up, the frequency will drift accordingly. Having the two external transistors tak e the job of switching the c oil power supply eases the burden on the IC and so does not heat up so much. The external transist ors will do that work inst ead. Keeping the IC running at lower temps will help keep it more stable. However, the transistor driver will drop approx. 1.4 volts from the overall output voltage. When using a 9 volt this starts to become an issue but with an adapter it is not an issue. If too much voltage is lost through the circuit by adding more transistors and diodes then one can use a higher rated adapter voltage. Say 14 volts instead of 12. My 12 volt adapter kicks out 16.5 volts even after it is loaded down, (connected to the circuit) and I still get lots of voltage at the coil.

The transistors shown in diagram 1b have the same power rating as the IC. There is a way to go beyond these limits but it involves using different external transistors to switch higher voltages and currents. So if you want to go past these limits then different transistors with higher ratings can be substituted. This will involve using two different power supplies in the system. One to power the 555 generator circuit and another to power the coil. Diagram 1c shows how the second power supply would be connected to the transistors and an example of another type of transistor to use. The transistors are good for lots of watts so be careful when doing your calculations for R6 and making sure the adapter can supply that much current. Otherwise you may end up destroying the adapter or worse, starting a fire after running it unattended and then the adapter burns itself up. The thing may run for a while before heating up to the point of self-destruction. A surefire check would be to have a digital multimeter that can measure amps (current) and place it in line on the power supply to verify how much current is being drawn. (See diagram) Having the multimeter inline on the output will only give you an average since the current is being pulsed. (Like AC electricity) If R6 is dissipating about 3 watts then it will have to be a 5 watt rated power resistor. In the standard circuit R6 is usually a 2 watt rated unit but even a 1 watt would suffice if the adapter voltage is low enough.


2/4

21/06/2010


One more note on power supply issues. D2 is a protection diode for accidental reversal of power supply. For 9 volt operation this will drop 0.7 volts off your 9 volt supply. If using external switching transistors then another 0.7v for each transistor is lost. So all these drops add up to 2.1V and 9 volts is not much to play with. I recommend that if one decides to increase the power in this manner that a second supply be used. It doesn’t have to be an adapter but say two 9 volts in series to give 18 volts. See next diagram 1d. This would work fine and would not require bigger better transistors to boot. If D2 is omitted (and it can be) there is a possibility even with a 9 volt battery clip, that you could reverse the polarity and damage the IC. All other components in the circuit would not be affected. And there is always the possibility of wiring up your adapter power supply polarity backwards and again fry the chip especially since it will probably be higher than a 9 volt supply. It looks to me from the 555 schematic that there is no reverse polarity power protection built within the chip so this is why I added this safety feature. It drops a little voltage but then you at least have that protection and won’t be blowing up chips all the time by accidental power polarity reversals.

With regards to the LED indicator: some of you may notice that the way it is positioned polarity-wise in the circuit is reversed from standard Hulda Clark style zapper circuits.. The reason I reversed the LED’s polarity is to allow more voltage to be available during the high pulse. So what this means is that when the pulse is low (not energizing the coil) then the LED will light up, thus not dropping any voltage when the pulse is high and the pulse IS energizing the coil. In the case of a zapper and the skin contact electrodes, this (the LED polarity) is an option for those who want to make a simple zapper that would increase the available voltage to the skin for zapping. Bob Beck’s blood electrifier design uses one battery to power the timer circuit and 3 batteries (9v) to use for zapping. I believe that this is a bett er zapper due to t he higher available voltage to penetrate ti ssue and overcome some of its electric al resis tance. This is not to say however, that people don’t get results with Hulda Clark’s design. But the LED reversal will increase the output voltage by about 3-4 volts. This makes a fair difference when the 9 volt starts to run down. Just thought I’d throw that little tidbit in here. This pretty much wraps up discussion of simple single frequency circuit designs. There are some fairly simple things that one can do to enhance the functionality of this very simple circuit to better suit its use for the Pulser . (ie. the DFMC-1)

The full article is several pages in the manual. You may wish to hold off from purchasing the manual until this page indicates that the revised edition has been made available and / or take note of the information above concerning the acknowledged error in the 555 circuit schematics included with the original construction manual. Realistically, the main body of information in the manual deals with the pulser itself, and several different methods can be used to provide a signal to the coil inside the pulser. Among the methods discussed in a comprehensive section on how to drive the coil (near the end of the manual) is the article from which the text above was taken. The Pulser construction manual: (manual is for design version II, design version III.2 built to order at Wizzers Workshop) How to Make an Orgone Field Pulser by Jon Logan includes electronics info by Kevin Smith published by Wizzers Workshop


3/4

21/06/2010

Zapper Circuit Schematics $15.00 USD PDF format / 3.15 MB 59 Pages / 79 Photos & Illustrations Tutorial - immediate download through vendor website after payment

TM TM TM TM TM is a trademark belonging to Karl Welz, the inventor of orgonite, and is used on litt lemountainsm udge.com for educational purposes. Wizzer's Workshop , Ergonite , Welzite , Wood Sprite , Water Baby , TM TM Chocolate Shine and O-Matrix Material are trademarks of Jon Logan, Owner ofli ttlemountainsm udge.com. All text and images on this site on this site, unless clearly otherwise stated, are copyright 2003-2006 Jon Logan, all rights reserved. Lim ited authorization to reproduce: This material may be reproduced or reprinted freely, in whol e or in part, for educational purposes. Owner ofcopyright for text and images on littlem ountainsmudg e.com and trademarks used on littlem ountainsmudg e.com reserves the right to refuse, suspend or revoke limited authorization to reproduce this material if the material is reproduced inaccurately, or if printed material from this website is sold at a cost in excess of it's production witho ut prior written consent from the owner, or if printed material from this site i s used commercially withou t stating in the printed copy t hat the material is copyright 2003-2006 Jon Logan. Webmasters using material from this site must include " courtesy Wizzers Workshop http://www.littl emountainsmud ge.com" at the end of the portion ofcontent whi ch is reproduced on your website. Orgonite

TM


4/4

Zapper Circuit Schematics

Recommend Documents