WOOD GROUP ESP, INC. USA STANDARD TERMS AND CONDITIONS OF SALE 1.
INTERPRETATION In these Standard Terms and Conditions: “Buyer” means the person, firm or company with whom the Contract is made; “Buyer Group” means the Buyer, its co-venturers, its and their respective affiliates and agents and its and their respective directors, officers and employees; “Contract” means the contract between the Seller and the Buyer for the sale and purchase of the Products and/or Services, incorporating these Standard Terms and Conditions; “Order Acknowledgement” means the written acceptance by Seller of Buyer’s purchase order or specification which shall incorporate these Standard terms and Conditions which forms the Contract; “Product(s)” means any products or parts agreed in the Contract to be supplied to the Buyer by the Seller; “Seller” means the selling entity identified in the Order Acknowledgement, or if none, the quotation; “Seller Group” means the Seller, its sub-suppliers, its and their respective affiliates and agents, its and their respective directors, officers and employees; “Services” means any services agreed in the Contract to be supplied to the Buyer by the Seller; “Special Conditions” means those Special Terms and Conditions set out in the Order Acknowledgement or other document issued by the Seller.
2.
APPLICABILITY
2.1
2.2 2.3
2.4 2.5 2.6 2.7
Subject to any variation under Section 2.3, the Contract shall be on these Standard Terms and Conditions to the exclusion of all other terms and conditions (including any terms and conditions which the Buyer purports to apply under any purchase order, confirmation of order, specification or other document). No terms or conditions endorsed on, delivered with or contained in the Buyer’s purchase order, confirmation of order, specification or other documents shall form part of the Contract simply as a result of such document being referred to in the Contract. These Standard Terms and Conditions apply to all the Seller’s sales and any variations to these Standard Terms and Conditions and any representations about the Products shall have no effect unless expressly agreed in writing and signed by an Authorized Signatory of the Seller. The Buyer acknowledges that it has not relied on any statement, promise or representation made or given by or on behalf of the Seller which is not set out in the Contract. Each order or acceptance of a quotation for Products by the Buyer from the Seller shall be deemed to be an offer by the Buyer to buy Products subject to these Standard Terms and Conditions. No order placed by the Buyer shall be deemed to be accepted by the Seller until an Order Acknowledgement is issued by the Seller, or (if earlier), the Seller delivers the Products or Services to the Buyer. The Buyer shall ensure that the terms of its order and any applicable specification are complete and accurate. Any quotation is given on the basis that no Contract shall come into existence until the Seller dispatches an Order Acknowledgement or delivers the Products or Services to the Buyer. Any quotation is valid for a period of 30 days only from its date, provided that the Seller has not previously withdrawn it. All quotations of Seller are subject to change at any time.
3.
PRICES All prices are subject to change without notice. Prices do not include packing and preparation of export shipment, inland or ocean freight, loading, unloading, carriage, insurance or forwarding fees, taxes, or duties of any kind or other similar charges applicable to the Products, Services and/or the Contract. Buyer agrees to pay such charges incurred by Seller on Buyer’s behalf together with additional handling charges upon receipt of Seller’s invoice for the same.
4.
TERMS OF PAYMENT Unless Seller and Buyer otherwise agree in writing to payment terms other than those specified herein, payment shall be made in U.S. dollars in accordance with remittance instructions furnished by Seller. (i) All payments shall be made within thirty (30) days after date of Seller’s invoice. (ii) Time for payment shall be of the essence. (iii) Seller may suspend credit to Buyer and may withhold shipment of Products ordered, suspend or cancel performance under these Standard Terms and Conditions if in its sole judgment the financial condition of the Buyer warrants such action. Suspension of performance may result in rescheduling delays. (iv) Prices do not include applicable taxes or duties. Buyer is solely responsible for paying all applicable taxes and duties. Seller will add taxes to the price where required by applicable law, and Buyer will pay all such taxes unless Buyer provides Seller with a duly executed tax exemption certificate in a form satisfactory to the Seller. If Buyer is required by applicable law to withhold any amount of tax from its payment to Seller, Buyer shall promptly pay such amount to the appropriate tax authority and take all reasonable steps to minimize such withholding tax. Buyer shall take all steps required to promptly obtain and deliver to Seller the appropriate certification of any such withholding in a form satisfactory to the Seller. (v) The Buyer shall make all payments due under the Contract in full without any deduction whether by way of set-off, counterclaim, discount, abatement or otherwise. (vi) All payments payable to the Seller under the Contract shall become due immediately on its termination despite any other provision.
Page 1 of 5
(vii)
5.
If the Buyer fails to pay the Seller any sum due pursuant to the Contract, the Buyer shall be liable to pay interest to the Seller on such sum from the due date for payment at the rate of eighteen percent (18%) per annum or at the highest rate allowed by law.
SHIPPING, DELIVERY, TITLE & RISK OF LOSS Products shall be delivered EXW (at location named by the Seller) (Incoterms 2000). Risk for loss or damage shall pass to Buyer upon Seller’s delivery to Buyer. Title shall pass to the Buyer upon receipt of payment in cleared funds by the Seller of amounts due in respect of the Contract. Seller may deliver the Products in installments. Each installment shall be a separate Contract and no cancellation or termination of any one Contract relating to an installment shall entitle the Buyer to repudiate or cancel any other Contract or installment. Delivery dates are intended to be an estimate and time and date for delivery shall not be made of the essence by notice or otherwise and are dependent on prompt receipt by Seller of all information and assistance required or requested by Seller to permit Seller to carry out its obligations under the Contract. Seller shall not be liable for any damage, losses or expenses incurred by Buyer if Seller fails to meet the estimated delivery dates. In the event that Products are not collected by Buyer on actual date of delivery, Seller may (at its sole discretion) place Products in storage at the sole cost, expense and risk of the Buyer.
6.
FORCE MAJEURE Seller reserves the right to defer the date of delivery of Products and/or the date of performance of Services, to cancel the Contract, or reduce the volume of the Products and/or amend the scope of the Services ordered by Buyer (without liability to Buyer) if it is prevented from or delayed in the carrying out of its business due to circumstances beyond its reasonable control, including but not limited to, natural disasters, forces of nature, earthquake, tidal wave, landslide, flood, lightening, hurricane, typhoon, storm or other weather condition not included in normal planning, epidemic and plague; changes in law or regulations, governmental actions; acts of civil or military authority; fire; explosion; lock-outs, strikes and/or labor disputes (whether or not relating to either party’s workforce); civil commotion; protests; war; national emergency; riot; civil insurrection; acts of terrorism; restraints or delays in transportation; restraints or delays in manufacturing and inability of Seller to obtain adequate or suitable supplies from usual sources, or acts of Buyer resulting in commercial impracticality. In the event of any such delay, the date of delivery and/or performance shall be deferred for a period equal to the time lost by reason of the delay.
7.
WARRANTY Seller warrants that Products manufactured by Seller, when properly stored, commissioned, installed, used and maintained, and Services performed by the Seller, shall be free from defects in material and workmanship. Seller’s obligation under this warranty shall be limited to replacing or repairing the part or parts or, the Products, at Seller’s option, which prove to be defective in material or workmanship within twelve (12) months from the date of installation or eighteen (18) months from the date of delivery, whichever shall occur first, or reperforming Services within twelve (12) months of the Services being supplied (“WARRANTY PERIOD”), provided the Buyer gives Seller prompt notice of any defect and provides proof in a form and substance satisfactory to the Seller (acting in its sole discretion) including all relevant data and documentation needed to assess well and equipment performance and operations. Any defective part or parts must be returned freight prepaid by Buyer to an authorized service center designated by Seller for inspection. Seller will deliver any replacements for defective Products to Buyer prepaid to the delivery destination provided by the original order. Products returned to the Seller for which Seller provides replacement under this warranty shall become the property of the Seller. THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR GUARANTEES, WHETHER ORAL, WRITTEN, EXPRESSED, IMPLIED OR STATUTORY, AND SELLER MAKES NO WARRANTY AS TO FITNESS FOR PURPOSE OR MERCHANTABILITY. SELLER’S WARRANTY OBLIGATIONS AND BUYER’S REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED HEREIN. THE WARRANTY PERIOD SHALL NOT BE EXTENDED FOR REPAIRED OR REPLACED PARTS OR PRODUCTS OR REPERFORMED SERVICES. SUCH PARTS OR PRODUCTS OR SERVICES SHALL REMAIN UNDER WARRANTY ONLY FOR THE UNEXPIRED PORTION OF THE WARRANTY PERIOD. SELLER’S SOLE LIABILITY SHALL BE AT ITS OPTION TO REPAIR OR REPLACE PARTS OR PRODUCTS OR REPERFORM SERVICES UNDER THIS CONDITION. SELLER MAY IN ITS SOLE DISCRETION CREDIT BUYER'S ACCOUNT FOR A PORTION OF SUCH PARTS OR PRODUCTS AND/OR SERVICES DETERMINED BY SELLER TO BE DEFECTIVE The foregoing warranty does not apply to: (a) defect caused or contributed to by abrasive materials, corrosion due to aggressive fluids, lightening, improper voltage supply, mishandling or misapplication; (b) Products or parts which are normally consumed in operation, or have a normal life inherently shorter than the WARRANTY PERIOD; (c) alterations or repairs carried out without prior written approval of the Seller, or using equipment and accessories for a purpose other than that for which such equipment and accessories are intended; (d) installations carried out by the Buyer unless Buyer’s engineers have been appropriately trained and certified by Seller; (e) installations in which Buyer has not used the application engineering practices for the Products as approved by Supplier; (f) defective Products or Services where Buyer makes further use of the Products after the earlier of the Buyer’s awareness of the defect or the time when the Buyer ought to have become aware of such defect; (g) defects arising from or in connection with information, drawings, chart interpretations, technical specifications or instructions provided by the Buyer to the Seller.
Page 2 of 5
8.
LIMITATION OF LIABILITY (i) FOR THE PURPOSE OF THIS SECTION 8(i), THE EXPRESSION "CONSEQUENTIAL LOSS" SHALL MEAN (IN EACH CASE WHETHER OR NOT FORESEEABLE AT THE DATE OF THE CONTRACT): (a) ANY AND ALL CONSEQUENTIAL, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE AND/OR SPECIAL LOSS AND/OR DAMAGE; AND (b) LOSS AND/OR DEFERRAL OF PRODUCTION, LOSS OF PRODUCT, LOSS OF GOODWILL, LOSS OF USE, LOSS OF REVENUE, PROFIT OR ANTICIPATED PROFIT, COST OF CAPITAL, IN EACH CASE WHETHER DIRECT OR INDIRECT TO THE EXTENT THAT SUCH LOSS, DEFERRAL AND/OR COST ARE NOT INCLUDED IN PARAGRAPH (a); AND (c) CLAIMS FOR SERVICE INTERRUPTION OR FAILURE TO SUPPLY, COSTS AND EXPENSES INCURRED IN CONNECTION WITH LABOR OVERHEAD, TRANSPORTATION OR SUBSTITUTE FACILITIES OR SUPPLY SOURCES, LABOR PERFORMED IN CONNECTION WITH THE REMOVAL AND REPLACEMENT OF PRODUCTS WITHIN THE WELL OR ANY OTHER LOSS OR DAMAGE INCURRED AS A RESULT OF OR OTHERWISE IN CONNECTION WITH INTERRUPTION OF SERVICE IN EACH CASE TO THE EXTENT THAT SUCH CLAIM IS NOT INCLUDED IN PARAGRAPH (i) OR PARAGRAPH (ii). NOTWITHSTANDING ANY PROVISION TO THE CONTRARY ELSEWHERE, IN NO CASE WILL THE SELLER BE LIABLE FOR CONSEQUENTIAL LOSS AND BUYER SHALL BE LIABLE FOR AND SHALL SAVE, INDEMNIFY, DEFEND AND HOLD HARMLESS THE SELLER GROUP FROM AND AGAINST ANY AND ALL CONSEQUENTIAL LOSS EVEN IF CAUSED BY THE SELLER'S SOLE, JOINT, COMPARATIVE, CONTRIBUTORY OR CONCURRENT NEGLIGENCE, FAULT, STRICT LIABILITY OR PRODUCT LIABILITY, AND REGARDLESS OF THE FORM OF ACTION, WHETHER CONTRACT, TORT (INCLUDING NEGLIGENCE), BREACH OF WARRANTY, INDEMNITY, STATUTE, STRICT LIABILITY OR OTHERWISE.
9.
(ii)
THE TOTAL LIABILITY OF SELLER ON ANY CLAIM WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE WHETHER SOLE OR CONCURRENT) OR OTHERWISE ARISING OUT OF, CONNECTED WITH, OR RESULTING FROM THE MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR, REPLACEMENT OR USE OF ANY PRODUCT, OR THE FURNISHING OF ANY SERVICE, OR THE PERFORMANCE OR NON-PERFORMANCE OF THE CONTRACT SHALL NOT EXCEED THE PRICE RECEIVED BY THE SELLER AND ALLOCABLE TO THE PRODUCT OR PART THEREOF, OR THE COST OF FURNISHING OF ANY SERVICE WORK WHICH GIVES RISE TO THE CLAIM.
(iii)
BUYER UNDERSTANDS AND AGREES THAT THE FOREGOING LIABILITY LIMITATIONS ARE ESSENTIAL ELEMENTS OF THE CONTRACT AND THAT IN THE ABSENCE OF SUCH LIMITATIONS THE MATERIAL AND ECONOMIC TERMS OF THIS CONTRACT WOULD BE SUBSTANTIALLY DIFFERENT.
INDEMNITIES All exclusions and indemnities given under this Section 9 (save for those under Sections 9.1(c) and 9.2(c)) and Section 8.1, shall apply irrespective of cause and notwithstanding the negligence or breach of duty (whether statutory or otherwise) of the indemnified party or any other entity or party and shall apply irrespective of any claim in tort, under contract or otherwise at law. For the purposes of Sections 9.1(c) and 9.2 (c), “third party” shall mean any party which is not a member of the Buyer Group nor the Seller Group. 9.1. The Seller shall be responsible for and shall save, indemnify, defend and hold harmless the Buyer Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of: (a) subject to Section 9.2(d), loss of or damage to property (other than the Products after delivery pursuant to Section 5) of the Seller Group whether owned, hired, leased or otherwise provided by the Seller Group arising from or relating to the performance of the Contract; (b) personal injury including death or disease to any person employed by the Seller Group arising from or relating to the performance of the Contract; and (c) subject to Section 9.3, personal injury including death or disease or loss of or damage to the property of any third party to the extent that any such injury, loss or damage is caused by the negligence or breach of duty (whether statutory or otherwise) of the Seller Group. 9.2 Buyer shall be responsible for and shall save, indemnify, defend and hold harmless Seller Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of: (a) loss of or damage to property of the Buyer Group, whether :(i) owned by the Buyer Group, or (ii) hired, leased or otherwise provided by or for the Buyer Group (including the Products after delivery pursuant to Section 5); and (b) personal injury including death or disease to any person employed by the Buyer Group arising from relating to or in connection with the performance or non-performance of the Contract; (c) subject to any other express provisions of the Contract, personal injury including death or disease or loss of or damage to the property of any third party to the extent that any such injury, loss or damage is caused by the negligence or breach of duty (whether statutory or otherwise) of the Buyer Group; and (d) at Seller’s option, either the repair or replacement or reimbursement of the full cost of Seller’s equipment, tools and/or instruments which are lost or damaged down-hole in the Buyer’s well during the provision of Services or are lost or
Page 3 of 5
damaged due to abrasion or corrosion occasioned by well effluents unless such loss or damage is due to the sole negligence of the Seller. 9.3 Notwithstanding Section 9.1, Buyer shall be liable for, and shall defend, indemnify and hold Seller Group harmless from and against, any and all claims which arise out of the performance or non-performance of the Contract in relation to the following, and whether or not resulting from, or contributed to by, the negligence of Seller Group; (i) loss of or damage to any well or hole or any third party oil and gas production facilities; (ii) reservoir seepage or pollution originating underground or from the property of the Buyer or third party howsoever arising; (iii) blow-out, fire, explosion, cratering of any well or reservoir or any other uncontrolled well condition (including the costs to control a wild well and the removal of debris); (iv) damage to or escape of product, or substance from any facility including any pipeline or other subsurface facility. 9.4 Notwithstanding anything to the contrary in the Contract, Buyer shall be responsible for and shall save, indemnify, defend and hold harmless Seller Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of any acts or omissions of the employees or agents of the Seller Group in connection with the performance of the Services (or any part of the Services), where, in accordance with the Contract, the employees of the Seller Group are under the supervision, direction or control of the Buyer in respect of those Services or part of the Services. 10
NON-DELIVERY The quantity of any consignment of Products as recorded by the Seller on dispatch from the Seller’s place of business or other designated location shall be conclusive evidence of the quantity received by Buyer on delivery unless Buyer can provide evidence proving the contrary. Seller shall not be liable for non-delivery of Products (even if caused by Seller’s negligence) unless Buyer gives written notice to the Seller of the non-delivery within forty eight (48) hours of the date and time when the Product would in the ordinary course of events have been received. Any liability of the Seller for non-delivery of the Products shall be limited to at Seller’s sole discretion either replacing the Products or issuing a credit note against any invoice raised for the Products.
11
PATENT INFRINGEMENT If Buyer receives a claim or otherwise becomes aware that any Product or part thereof manufactured by Seller infringes or allegedly infringes a patent or other intellectual property right, Buyer shall notify Seller immediately in writing and give Seller information, assistance and exclusive authority to evaluate, defend and settle such claim or potential infringement. Seller shall then at its own expense and option (a) settle such claim, or (b) procure for Buyer the right to use such Product, or (c) replace or modify it to avoid infringement, or (d) remove it and refund the purchase price (including transportation and installation costs) less a reasonable amount for depreciation, or (e) defend against such claim.
12
CANCELLATION AND CHANGES The Buyer may not cancel or reschedule the delivery date of any Product and/or Services to be provided under the Contract without the prior written consent of the Seller. In the event that the Seller provides such consent, any such cancellation or rescheduling of Product and/or Services by Buyer will result in a charge to Buyer to be determined by the Seller. All specially designed or modified Products cancelled after commencement of manufacture will be subject to a cancellation charge which will include all costs and a reasonable margin for time employed, as determined by Seller. Cancellation charges for accessories and components sourced from third parties will be charged at full price. Seller shall, at its sole discretion, adjust the price or delivery dates or make such other amendments as may be required as a result of any change order agreed to be issued by the Buyer and Seller. No amendment to a purchase order or Order Acknowledgement or change order shall be valid unless agreed in writing by the Seller (at its sole discretion).
13
WAIVER Any waiver by Seller of any breach or default by Buyer of any of the Buyer’s obligations under the Contract, or any failure by Seller to enforce any rights arising under the Contract shall not be construed as a waiver of any other or subsequent breach or default by Buyer or of Seller’s right to enforce its rights arising hereunder in any circumstances. In the event of any default by Buyer, Seller may decline to make further shipments. If Seller elects to continue to make deliveries, Seller’s action shall not constitute a waiver of any such default or affect Seller’s remedies for any such default.
14
ENTIRE AGREEMENT: The Order Acknowledgement, any Special Conditions and these Standard Terms and Conditions constitute the entire agreement between the parties relating to the sale of the Products and/or Services and supersedes all previous communications, representations, or agreements, either oral or written, with respect to the subject matter hereof. No prior representations or statements relating to the sale of the Products and/or Services made by any Seller representative, which are not stated herein, shall be binding on Seller.
15
EXPORT CONTROL Buyer agrees that unless prior authorization is obtained from the U.S. Department of Commerce, neither Buyer nor its subsidiaries shall export, re-export, or release, directly or indirectly, any Product received from Seller to any destination or country to which the export, reexport or release of the technology or Product is prohibited by the Export Administration Regulations of the U.S. Department of Commerce ("EAR"), or prohibited by US or applicable non-US laws. Buyer will be responsible for obtaining any necessary export license or other documentation prior to the exportation or re-exportation of any Product acquired from Seller under the Contract. Further, Buyer shall give notice of the need to comply with such laws and regulations to any person, firm or entity which it has reason to believe is obtaining any such Product from Buyer with the intention of exportation. Each party shall secure, at its own expense, such licenses and export and import documents as are necessary for each respective party to fulfill its obligations under the Contract. If approvals cannot be obtained, Seller may terminate, cancel or otherwise
Page 4 of 5
be excused from performing any obligations it may have under the Contract. Any export classification made by Seller shall be for Seller's internal use only and shall not be construed as a representation or warranty regarding the proper export classification for such Product or whether an export license or other documentation is required for the exportation of such Product. This Section 15 shall survive termination of the Contract. 16
BUSINESS ETHICS Neither Seller nor Buyer shall make any payment or take any action that could be construed to be the payment of money or other thing of value to any government official, political party, or political party candidate for the purpose of influencing any act or inducing any government official to use his or its influence to assist in obtaining or retaining business in any country in a manner which is illegal or which would subject the Seller to civil or criminal penalties, or which is inconsistent with Seller’s Business Ethics Policy.
17
ASSIGNMENT The Seller may assign this Contract or any part of it to any person, firm or company. The Buyer shall not be entitled to assign the Contract or any part of it without the prior written consent of the Seller.
18
ARBITRATION The parties agree that any and all disputes or controversies that may arise between the parties arising out of or related to this Contract shall be determined by binding arbitration. Any such arbitration shall be determined before the American Arbitration Association (“AAA”) in accordance with AAA rules then in effect, with each party nominating one arbiter and the two arbiters nominating a third, and that any arbitration proceedings shall be held in Oklahoma City, Oklahoma. Judgment upon arbitration awards may be entered in any court, state or federal, having jurisdiction.
19
GOVERNING LAW This Contract shall be governed and construed in accordance with the laws of the State of Oklahoma, without giving effect to any conflicts of laws principles.
20
MISCELLANEOUS All samples, drawings, descriptive matter, specifications and advertising issued by the Seller and any descriptions or illustrations contained in the Seller’s catalogues or brochures are issued or published for the sole purpose of giving an approximate idea of the Products and/or Services described in them. They shall not form part of the Contract. The Buyer shall at its own expense secure any permits or any other authorizations (including but not limited to work permits and visas for employees of the Seller) which may be required to permit the Seller to perform the Services. The Buyer agrees to indemnify the Seller against any costs, claims, actions, demands or expenses incurred or suffered in connection with the Buyer’s failure to obtain any permits or authorizations required to perform the Services. If any provision of the Contract is found by any court, tribunal or administrative body of competent jurisdiction to be wholly or partly illegal, invalid, void, voidable, unenforceable or unreasonable it shall to the extent of such illegality, invalidity, voidness, voidability, unenforceability or unreasonableness be deemed severable and the remaining provisions of the Contract and the remainder of such provision shall continue in full force. These Standard Terms and Conditions are subject to change without prior written notice at any time and from time to time at the Seller’s sole discretion. All communications between the parties about the Contract shall be in writing and delivered by hand or sent by fax to its registered office or such other address as shall be notified to the other party. Communications shall be deemed to have been received if delivered by hand, on the day of delivery or if sent by fax on a business day at the time of transmission and otherwise on the next working day.
Page 5 of 5
WOOD GROUP ESP (CANADA) LTD. STANDARD TERMS AND CONDITIONS OF SALE 1.
INTERPRETATION In these Standard Terms and Conditions: “Buyer” means the person, firm or company with whom the Contract is made; “Buyer Group” means the Buyer, its co-venturers, its and their respective affiliates and agents and its and their respective directors, officers and employees; “Contract” means the contract between the Seller and the Buyer for the sale and purchase of the Products and/or Services, incorporating these Standard Terms and Conditions; “Order Acknowledgement” means the written acceptance by Seller of Buyer’s purchase order or specification which shall incorporate these Standard terms and Conditions which forms the Contract; “Product(s)” means any products or parts agreed in the Contract to be supplied to the Buyer by the Seller; “Seller” means the selling entity identified in the Order Acknowledgement, or if none, the quotation; “Seller Group” means the Seller, its sub-suppliers, its and their respective affiliates and agents, its and their respective directors, officers and employees; “Services” means any services agreed in the Contract to be supplied to the Buyer by the Seller; “Special Conditions” means those Special Terms and Conditions set out in the Order Acknowledgement or other document issued by the Seller.
2.
APPLICABILITY
2.1
2.2 2.3
2.4 2.5 2.6 2.7
Subject to any variation under Section 2.3, the Contract shall be on these Standard Terms and Conditions to the exclusion of all other terms and conditions (including any terms and conditions which the Buyer purports to apply under any purchase order, confirmation of order, specification or other document). No terms or conditions endorsed on, delivered with or contained in the Buyer’s purchase order, confirmation of order, specification or other documents shall form part of the Contract simply as a result of such document being referred to in the Contract. These Standard Terms and Conditions apply to all the Seller’s sales and any variations to these Standard Terms and Conditions and any representations about the Products shall have no effect unless expressly agreed in writing and signed by an Authorized Signatory of the Seller. The Buyer acknowledges that it has not relied on any statement, promise or representation made or given by or on behalf of the Seller which is not set out in the Contract. Each order or acceptance of a quotation for Products by the Buyer from the Seller shall be deemed to be an offer by the Buyer to buy Products subject to these Standard Terms and Conditions. No order placed by the Buyer shall be deemed to be accepted by the Seller until an Order Acknowledgement is issued by the Seller, or (if earlier), the Seller delivers the Products or Services to the Buyer. The Buyer shall ensure that the terms of its order and any applicable specification are complete and accurate. Any quotation is given on the basis that no Contract shall come into existence until the Seller dispatches an Order Acknowledgement or delivers the Products or Services to the Buyer. Any quotation is valid for a period of 30 days only from its date, provided that the Seller has not previously withdrawn it. All quotations of Seller are subject to change at any time.
3.
PRICES All prices are subject to change without notice. Prices do not include packing and preparation of export shipment, inland or ocean freight, loading, unloading, carriage, insurance or forwarding fees, taxes, or duties of any kind or other similar charges applicable to the Products, Services and/or the Contract. Buyer agrees to pay such charges incurred by Seller on Buyer’s behalf together with additional handling charges upon receipt of Seller’s invoice for the same.
4.
TERMS OF PAYMENT Unless Seller and Buyer otherwise agree in writing to payment terms other than those specified herein, payment shall be made in U.S. dollars in accordance with remittance instructions furnished by Seller. (i) All payments shall be made within thirty (30) days after date of Seller’s invoice. (ii) Time for payment shall be of the essence. (iii) Seller may suspend credit to Buyer and may withhold shipment of Products ordered, suspend or cancel performance under these Standard Terms and Conditions if in its sole judgment the financial condition of the Buyer warrants such action. Suspension of performance may result in rescheduling delays. (iv) Prices do not include applicable taxes or duties. Buyer is solely responsible for paying all applicable taxes and duties. Seller will add taxes to the price where required by applicable law, and Buyer will pay all such taxes unless Buyer provides Seller with a duly executed tax exemption certificate in a form satisfactory to the Seller. If Buyer is required by applicable law to withhold any amount of tax from its payment to Seller, Buyer shall promptly pay such amount to the appropriate tax authority and take all reasonable steps to minimize such withholding tax. Buyer shall take all steps required to promptly obtain and deliver to Seller the appropriate certification of any such withholding in a form satisfactory to the Seller. (v) The Buyer shall make all payments due under the Contract in full without any deduction whether by way of set-off, counterclaim, discount, abatement or otherwise. (vi) All payments payable to the Seller under the Contract shall become due immediately on its termination despite any other provision.
Page 1 of 5
(vii)
5.
If the Buyer fails to pay the Seller any sum due pursuant to the Contract, the Buyer shall be liable to pay interest to the Seller on such sum from the due date for payment at the rate of eighteen percent (18%) per annum or at the highest rate allowed by law.
SHIPPING, DELIVERY, TITLE & RISK OF LOSS Products shall be delivered EXW (at location named by the Seller) (Incoterms 2000). Risk for loss or damage shall pass to Buyer upon Seller’s delivery to Buyer. Title shall pass to the Buyer upon receipt of payment in cleared funds by the Seller of amounts due in respect of the Contract. Seller may deliver the Products in installments. Each installment shall be a separate Contract and no cancellation or termination of any one Contract relating to an installment shall entitle the Buyer to repudiate or cancel any other Contract or installment. Delivery dates are intended to be an estimate and time and date for delivery shall not be made of the essence by notice or otherwise and are dependent on prompt receipt by Seller of all information and assistance required or requested by Seller to permit Seller to carry out its obligations under the Contract. Seller shall not be liable for any damage, losses or expenses incurred by Buyer if Seller fails to meet the estimated delivery dates. In the event that Products are not collected by Buyer on actual date of delivery, Seller may (at its sole discretion) place Products in storage at the sole cost, expense and risk of the Buyer.
6.
FORCE MAJEURE Seller reserves the right to defer the date of delivery of Products and/or the date of performance of Services, to cancel the Contract, or reduce the volume of the Products and/or amend the scope of the Services ordered by Buyer (without liability to Buyer) if it is prevented from or delayed in the carrying out of its business due to circumstances beyond its reasonable control, including but not limited to, natural disasters, forces of nature, earthquake, tidal wave, landslide, flood, lightening, hurricane, typhoon, storm or other weather condition not included in normal planning, epidemic and plague; changes in law or regulations, governmental actions; acts of civil or military authority; fire; explosion; lock-outs, strikes and/or labor disputes (whether or not relating to either party’s workforce); civil commotion; protests; war; national emergency; riot; civil insurrection; acts of terrorism; restraints or delays in transportation; restraints or delays in manufacturing and inability of Seller to obtain adequate or suitable supplies from usual sources, or acts of Buyer resulting in commercial impracticality. In the event of any such delay, the date of delivery and/or performance shall be deferred for a period equal to the time lost by reason of the delay.
7.
WARRANTY Seller warrants that Products manufactured by Seller, when properly stored, commissioned, installed, used and maintained, and Services performed by the Seller, shall be free from defects in material and workmanship. Seller’s obligation under this warranty shall be limited to replacing or repairing the part or parts or, the Products, at Seller’s option, which prove to be defective in material or workmanship within twelve (12) months from the date of installation or eighteen (18) months from the date of delivery, whichever shall occur first, or reperforming Services within twelve (12) months of the Services being supplied (“WARRANTY PERIOD”), provided the Buyer gives Seller prompt notice of any defect and provides proof in a form and substance satisfactory to the Seller (acting in its sole discretion) including all relevant data and documentation needed to assess well and equipment performance and operations. Any defective part or parts must be returned freight prepaid by Buyer to an authorized service center designated by Seller for inspection. Seller will deliver any replacements for defective Products to Buyer prepaid to the delivery destination provided by the original order. Products returned to the Seller for which Seller provides replacement under this warranty shall become the property of the Seller. THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR GUARANTEES, WHETHER ORAL, WRITTEN, EXPRESSED, IMPLIED OR STATUTORY, AND SELLER MAKES NO WARRANTY AS TO FITNESS FOR PURPOSE OR MERCHANTABILITY. SELLER’S WARRANTY OBLIGATIONS AND BUYER’S REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED HEREIN. THE WARRANTY PERIOD SHALL NOT BE EXTENDED FOR REPAIRED OR REPLACED PARTS OR PRODUCTS OR REPERFORMED SERVICES. SUCH PARTS OR PRODUCTS OR SERVICES SHALL REMAIN UNDER WARRANTY ONLY FOR THE UNEXPIRED PORTION OF THE WARRANTY PERIOD. SELLER’S SOLE LIABILITY SHALL BE AT ITS OPTION TO REPAIR OR REPLACE PARTS OR PRODUCTS OR REPERFORM SERVICES UNDER THIS CONDITION. SELLER MAY IN ITS SOLE DISCRETION CREDIT BUYER'S ACCOUNT FOR A PORTION OF SUCH PARTS OR PRODUCTS AND/OR SERVICES DETERMINED BY SELLER TO BE DEFECTIVE The foregoing warranty does not apply to: (a) defect caused or contributed to by abrasive materials, corrosion due to aggressive fluids, lightening, improper voltage supply, mishandling or misapplication; (b) Products or parts which are normally consumed in operation, or have a normal life inherently shorter than the WARRANTY PERIOD; (c) alterations or repairs carried out without prior written approval of the Seller, or using equipment and accessories for a purpose other than that for which such equipment and accessories are intended; (d) installations carried out by the Buyer unless Buyer’s engineers have been appropriately trained and certified by Seller; (e) installations in which Buyer has not used the application engineering practices for the Products as approved by Supplier; (f) defective Products or Services where Buyer makes further use of the Products after the earlier of the Buyer’s awareness of the defect or the time when the Buyer ought to have become aware of such defect; (g) defects arising from or in connection with information, drawings, chart interpretations, technical specifications or instructions provided by the Buyer to the Seller.
Page 2 of 5
8.
LIMITATION OF LIABILITY (i) FOR THE PURPOSE OF THIS SECTION 8(i), THE EXPRESSION "CONSEQUENTIAL LOSS" SHALL MEAN (IN EACH CASE WHETHER OR NOT FORESEEABLE AT THE DATE OF THE CONTRACT): (a) ANY AND ALL CONSEQUENTIAL, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE AND/OR SPECIAL LOSS AND/OR DAMAGE; AND (b) LOSS AND/OR DEFERRAL OF PRODUCTION, LOSS OF PRODUCT, LOSS OF GOODWILL, LOSS OF USE, LOSS OF REVENUE, PROFIT OR ANTICIPATED PROFIT, COST OF CAPITAL, IN EACH CASE WHETHER DIRECT OR INDIRECT TO THE EXTENT THAT SUCH LOSS, DEFERRAL AND/OR COST ARE NOT INCLUDED IN PARAGRAPH (a); AND (c) CLAIMS FOR SERVICE INTERRUPTION OR FAILURE TO SUPPLY, COSTS AND EXPENSES INCURRED IN CONNECTION WITH LABOR OVERHEAD, TRANSPORTATION OR SUBSTITUTE FACILITIES OR SUPPLY SOURCES, LABOR PERFORMED IN CONNECTION WITH THE REMOVAL AND REPLACEMENT OF PRODUCTS WITHIN THE WELL OR ANY OTHER LOSS OR DAMAGE INCURRED AS A RESULT OF OR OTHERWISE IN CONNECTION WITH INTERRUPTION OF SERVICE IN EACH CASE TO THE EXTENT THAT SUCH CLAIM IS NOT INCLUDED IN PARAGRAPH (i) OR PARAGRAPH (ii). NOTWITHSTANDING ANY PROVISION TO THE CONTRARY ELSEWHERE, IN NO CASE WILL THE SELLER BE LIABLE FOR CONSEQUENTIAL LOSS AND BUYER SHALL BE LIABLE FOR AND SHALL SAVE, INDEMNIFY, DEFEND AND HOLD HARMLESS THE SELLER GROUP FROM AND AGAINST ANY AND ALL CONSEQUENTIAL LOSS EVEN IF CAUSED BY THE SELLER'S SOLE, JOINT, COMPARATIVE, CONTRIBUTORY OR CONCURRENT NEGLIGENCE, FAULT, STRICT LIABILITY OR PRODUCT LIABILITY, AND REGARDLESS OF THE FORM OF ACTION, WHETHER CONTRACT, TORT (INCLUDING NEGLIGENCE), BREACH OF WARRANTY, INDEMNITY, STATUTE, STRICT LIABILITY OR OTHERWISE.
9.
(ii)
THE TOTAL LIABILITY OF SELLER ON ANY CLAIM WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE WHETHER SOLE OR CONCURRENT) OR OTHERWISE ARISING OUT OF, CONNECTED WITH, OR RESULTING FROM THE MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR, REPLACEMENT OR USE OF ANY PRODUCT, OR THE FURNISHING OF ANY SERVICE, OR THE PERFORMANCE OR NON-PERFORMANCE OF THE CONTRACT SHALL NOT EXCEED THE PRICE RECEIVED BY THE SELLER AND ALLOCABLE TO THE PRODUCT OR PART THEREOF, OR THE COST OF FURNISHING OF ANY SERVICE WORK WHICH GIVES RISE TO THE CLAIM.
(iii)
BUYER UNDERSTANDS AND AGREES THAT THE FOREGOING LIABILITY LIMITATIONS ARE ESSENTIAL ELEMENTS OF THE CONTRACT AND THAT IN THE ABSENCE OF SUCH LIMITATIONS THE MATERIAL AND ECONOMIC TERMS OF THIS CONTRACT WOULD BE SUBSTANTIALLY DIFFERENT.
INDEMNITIES All exclusions and indemnities given under this Section 9 (save for those under Sections 9.1(c) and 9.2(c)) and Section 8.1, shall apply irrespective of cause and notwithstanding the negligence or breach of duty (whether statutory or otherwise) of the indemnified party or any other entity or party and shall apply irrespective of any claim in tort, under contract or otherwise at law. For the purposes of Sections 9.1(c) and 9.2 (c), “third party” shall mean any party which is not a member of the Buyer Group nor the Seller Group. 9.1. The Seller shall be responsible for and shall save, indemnify, defend and hold harmless the Buyer Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of: (a) subject to Section 9.2(d), loss of or damage to property (other than the Products after delivery pursuant to Section 5) of the Seller Group whether owned, hired, leased or otherwise provided by the Seller Group arising from or relating to the performance of the Contract; (b) personal injury including death or disease to any person employed by the Seller Group arising from or relating to the performance of the Contract; and (c) subject to Section 9.3, personal injury including death or disease or loss of or damage to the property of any third party to the extent that any such injury, loss or damage is caused by the negligence or breach of duty (whether statutory or otherwise) of the Seller Group. 9.2 Buyer shall be responsible for and shall save, indemnify, defend and hold harmless Seller Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of: (a) loss of or damage to property of the Buyer Group, whether :(i) owned by the Buyer Group, or (ii) hired, leased or otherwise provided by or for the Buyer Group (including the Products after delivery pursuant to Section 5); and (b) personal injury including death or disease to any person employed by the Buyer Group arising from relating to or in connection with the performance or non-performance of the Contract; (c) subject to any other express provisions of the Contract, personal injury including death or disease or loss of or damage to the property of any third party to the extent that any such injury, loss or damage is caused by the negligence or breach of duty (whether statutory or otherwise) of the Buyer Group; and (d) at Seller’s option, either the repair or replacement or reimbursement of the full cost of Seller’s equipment, tools and/or instruments which are lost or damaged down-hole in the Buyer’s well during the provision of Services or are lost or
Page 3 of 5
damaged due to abrasion or corrosion occasioned by well effluents unless such loss or damage is due to the sole negligence of the Seller. 9.3 Notwithstanding Section 9.1, Buyer shall be liable for, and shall defend, indemnify and hold Seller Group harmless from and against, any and all claims which arise out of the performance or non-performance of the Contract in relation to the following, and whether or not resulting from, or contributed to by, the negligence of Seller Group; (i) loss of or damage to any well or hole or any third party oil and gas production facilities; (ii) reservoir seepage or pollution originating underground or from the property of the Buyer or third party howsoever arising; (iii) blow-out, fire, explosion, cratering of any well or reservoir or any other uncontrolled well condition (including the costs to control a wild well and the removal of debris); (iv) damage to or escape of product, or substance from any facility including any pipeline or other subsurface facility. 9.4 Notwithstanding anything to the contrary in the Contract, Buyer shall be responsible for and shall save, indemnify, defend and hold harmless Seller Group from and against all claims, losses, damages, costs (including legal costs) expenses and liabilities in respect of any acts or omissions of the employees or agents of the Seller Group in connection with the performance of the Services (or any part of the Services), where, in accordance with the Contract, the employees of the Seller Group are under the supervision, direction or control of the Buyer in respect of those Services or part of the Services. 10
NON-DELIVERY The quantity of any consignment of Products as recorded by the Seller on dispatch from the Seller’s place of business or other designated location shall be conclusive evidence of the quantity received by Buyer on delivery unless Buyer can provide evidence proving the contrary. Seller shall not be liable for non-delivery of Products (even if caused by Seller’s negligence) unless Buyer gives written notice to the Seller of the non-delivery within forty eight (48) hours of the date and time when the Product would in the ordinary course of events have been received. Any liability of the Seller for non-delivery of the Products shall be limited to at Seller’s sole discretion either replacing the Products or issuing a credit note against any invoice raised for the Products.
11
PATENT INFRINGEMENT If Buyer receives a claim or otherwise becomes aware that any Product or part thereof manufactured by Seller infringes or allegedly infringes a patent or other intellectual property right, Buyer shall notify Seller immediately in writing and give Seller information, assistance and exclusive authority to evaluate, defend and settle such claim or potential infringement. Seller shall then at its own expense and option (a) settle such claim, or (b) procure for Buyer the right to use such Product, or (c) replace or modify it to avoid infringement, or (d) remove it and refund the purchase price (including transportation and installation costs) less a reasonable amount for depreciation, or (e) defend against such claim.
12
CANCELLATION AND CHANGES The Buyer may not cancel or reschedule the delivery date of any Product and/or Services to be provided under the Contract without the prior written consent of the Seller. In the event that the Seller provides such consent, any such cancellation or rescheduling of Product and/or Services by Buyer will result in a charge to Buyer to be determined by the Seller. All specially designed or modified Products cancelled after commencement of manufacture will be subject to a cancellation charge which will include all costs and a reasonable margin for time employed, as determined by Seller. Cancellation charges for accessories and components sourced from third parties will be charged at full price. Seller shall, at its sole discretion, adjust the price or delivery dates or make such other amendments as may be required as a result of any change order agreed to be issued by the Buyer and Seller. No amendment to a purchase order or Order Acknowledgement or change order shall be valid unless agreed in writing by the Seller (at its sole discretion).
13
WAIVER Any waiver by Seller of any breach or default by Buyer of any of the Buyer’s obligations under the Contract, or any failure by Seller to enforce any rights arising under the Contract shall not be construed as a waiver of any other or subsequent breach or default by Buyer or of Seller’s right to enforce its rights arising hereunder in any circumstances. In the event of any default by Buyer, Seller may decline to make further shipments. If Seller elects to continue to make deliveries, Seller’s action shall not constitute a waiver of any such default or affect Seller’s remedies for any such default.
14
ENTIRE AGREEMENT: The Order Acknowledgement, any Special Conditions and these Standard Terms and Conditions constitute the entire agreement between the parties relating to the sale of the Products and/or Services and supersedes all previous communications, representations, or agreements, either oral or written, with respect to the subject matter hereof. No prior representations or statements relating to the sale of the Products and/or Services made by any Seller representative, which are not stated herein, shall be binding on Seller.
15
EXPORT CONTROL Buyer agrees that unless prior authorization is obtained from the U.S. Department of Commerce, neither Buyer nor its subsidiaries shall export, re-export, or release, directly or indirectly, any Product received from Seller to any destination or country to which the export, reexport or release of the technology or Product is prohibited by the Export Administration Regulations of the U.S. Department of Commerce ("EAR"), or prohibited by US or applicable non-US laws. Buyer will be responsible for obtaining any necessary export license or other documentation prior to the exportation or re-exportation of any Product acquired from Seller under the Contract. Further, Buyer shall give notice of the need to comply with such laws and regulations to any person, firm or entity which it has reason to believe is obtaining any such Product from Buyer with the intention of exportation. Each party shall secure, at its own expense, such licenses and export and import documents as are necessary for each respective party to fulfill its obligations under the Contract. If approvals cannot be obtained, Seller may terminate, cancel or otherwise
Page 4 of 5
be excused from performing any obligations it may have under the Contract. Any export classification made by Seller shall be for Seller's internal use only and shall not be construed as a representation or warranty regarding the proper export classification for such Product or whether an export license or other documentation is required for the exportation of such Product. This Section 15 shall survive termination of the Contract. 16
BUSINESS ETHICS Neither Seller nor Buyer shall make any payment or take any action that could be construed to be the payment of money or other thing of value to any government official, political party, or political party candidate for the purpose of influencing any act or inducing any government official to use his or its influence to assist in obtaining or retaining business in any country in a manner which is illegal or which would subject the Seller to civil or criminal penalties, or which is inconsistent with Seller’s Business Ethics Policy.
17
ASSIGNMENT The Seller may assign this Contract or any part of it to any person, firm or company. The Buyer shall not be entitled to assign the Contract or any part of it without the prior written consent of the Seller.
18
ARBITRATION The parties agree that any and all disputes or controversies that may arise between the parties arising out of or related to this Contract shall be determined by binding arbitration. Any such arbitration shall be determined before the American Arbitration Association (“AAA”) in accordance with AAA rules then in effect, with each party nominating one arbiter and the two arbiters nominating a third, and that any arbitration proceedings shall be held in Oklahoma City, Oklahoma, USA. Judgment upon arbitration awards may be entered in any court, state or federal, having jurisdiction.
19
GOVERNING LAW This Contract shall be governed and construed in accordance with the laws of the State of Oklahoma, USA, without giving effect to any conflicts of laws principles.
20
MISCELLANEOUS All samples, drawings, descriptive matter, specifications and advertising issued by the Seller and any descriptions or illustrations contained in the Seller’s catalogues or brochures are issued or published for the sole purpose of giving an approximate idea of the Products and/or Services described in them. They shall not form part of the Contract. The Buyer shall at its own expense secure any permits or any other authorizations (including but not limited to work permits and visas for employees of the Seller) which may be required to permit the Seller to perform the Services. The Buyer agrees to indemnify the Seller against any costs, claims, actions, demands or expenses incurred or suffered in connection with the Buyer’s failure to obtain any permits or authorizations required to perform the Services. If any provision of the Contract is found by any court, tribunal or administrative body of competent jurisdiction to be wholly or partly illegal, invalid, void, voidable, unenforceable or unreasonable it shall to the extent of such illegality, invalidity, voidness, voidability, unenforceability or unreasonableness be deemed severable and the remaining provisions of the Contract and the remainder of such provision shall continue in full force. These Standard Terms and Conditions are subject to change without prior written notice at any time and from time to time at the Seller’s sole discretion. All communications between the parties about the Contract shall be in writing and delivered by hand or sent by fax to its registered office or such other address as shall be notified to the other party. Communications shall be deemed to have been received if delivered by hand, on the day of delivery or if sent by fax on a business day at the time of transmission and otherwise on the next working day.
Page 5 of 5
WOOD GROUP ESP TÉRMINOS Y CONDICIONES DE VENTA ESTÁNDAR 1.
INTERPRETACIÓN En estos Términos y Condiciones de Venta Estándar: “Comprador” significa la persona, firma o empresa con quien se celebra el Contrato; “Grupo del Comprador” significa el Comprador, sus accionistas, sus empresas asociadas, sus afiliadas y agentes y sus respectivos directores, empleados de alto rango y empleados en general; “Contrato” significa el contrato celebrado entre el Vendedor y el Comprador para la venta y compra de los Productos y/o Servicios, incorporando estos Términos y Condiciones Estándar; “Acuse de Recibo de la Orden” significa la aceptación por escrito por parte del Vendedor de la orden de compra o especificaciones del Comprador que incorporarán estos Términos y Condiciones Estándar que constituyen el Contrato; “Producto(s)” significa los productos o partes cuyo suministro por el Vendedor al Comprador se acuerda en el Contrato; “Vendedor” significa la entidad vendedora identificada en el Acuse de Recibo de la Orden, o de no haber uno, en la cotización; “Grupo del Vendedor” significa el Vendedor, sus accionistas, sus sub-proveedores, y sus respectivas afiliadas y agentes y sus respectivos directores, altos empleados y empleados en general; “Servicios” significa los servicios cuyo suministro por el Vendedor al Comprador se acuerda en el Contrato; “Condiciones especiales” significa los Términos y Condiciones Especiales establecidos en el Acuse de Recibo de la Orden u otro documento expedido por el Vendedor.
2.
APLICABILIDAD
2.1. Sujeto a cualquier variación bajo la condición 2.3, el Contrato consistirá de estos Términos y Condiciones Estándar con exclusión de cualquier otros términos y condiciones (incluyendo los términos y condiciones que el Comprador tenga por intención aplicar bajo cualquier orden de compra, confirmación de la orden, especificaciones u otro documento). 2.2. Los términos y condiciones aprobados, entregados o contenidos, respectivamente, en la orden de compra del Comprador, confirmación de la orden, especificaciones u otros documentos no formarán parte del Contrato simplemente por el hecho de que dichos documentos sean referidos en el Contrato. 2.3. Estos Términos y Condiciones Estándar se aplicarán a todas las ventas del Vendedor y los cambios de dichos Términos y Condiciones Estándar y las representaciones hechas acerca de los Productos no tendrán ningún efecto, salvo que sean acordados en forma expresa por escrito y lleven la firma de un Signatario autorizado por el Vendedor. El Comprador reconoce que no ha actuado en base a declaración, promesa o representación alguna hecha o manifestada por el Vendedor, o en nombre del Vendedor, que no figure en el Contrato. 2.4. Cada orden o aceptación de una cotización de Productos del Vendedor por parte del Comprador se considerará como una oferta del Comprador para la compra de Productos, sujeta a estos Términos y Condiciones Estándar. 2.5. Ninguna orden colocada por el Comprador se considerará aceptada por el Vendedor hasta que se expida el Acuse de Recibo de la Orden por el Vendedor, o, hasta que el Vendedor entregue los Productos o suministre los Servicios al Comprador, lo que ocurra primero. 2.6. El Comprador se asegurará de que los términos de su orden y las especificaciones aplicables se formulen en forma completa y precisa. 2.7. La cotización se hace sobre la base de que el Contrato no entrará en vigencia hasta que el Vendedor expida el Acuse de Recibo de la Orden o entregue los Productos o suministre los Servicios al Comprador. La cotización es válida por un período de 30 días contados desde la fecha de la misma, siempre que el Vendedor no la haya retirado anteriormente. Todas las cotizaciones del Vendedor están sujetas a cambio en cualquier momento. 3.
PRECIOS
Página 1 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
Todos los precios están sujetos a cambio sin aviso. Los precios no incluyen el empaque y preparación del embarque de exportación, flete terrestre o marítimo, carga, descarga, transporte, seguro o comisión del agente de expedición de la mercadería, impuestos o derechos de aduana de cualquier clase u otros cobros similares aplicables a los Productos, Servicios y/o el Contrato. El Comprador acuerda pagar los costos incurridos por el Vendedor en nombre del Comprador, junto con los gastos de manipulación adicionales una vez que reciba la factura del Vendedor por los mismos. 4.
TÉRMINOS DE PAGO Salvo que el Vendedor y el Comprador acuerden por escrito términos de pago distintos a los estipulados en el presente el pago se hará en dólares estadounidenses, conforme con las instrucciones de remesa proporcionadas por el Vendedor. (i) El pago se hará mediante carta de crédito a ser abierta por el Comprador, a su costo, incluyendo los gastos de confirmación. Todas las cartas de crédito serán en favor del Vendedor, y en una forma que sea aceptable para el Vendedor, deberán ser por las cantidades que sean suficientes y por los períodos que sean necesarios para cumplir con todas las obligaciones de pago, serán irrevocables y se emitirán o confirmarán por un banco que sea satisfactorio para el Vendedor, dentro de los 30 días de la expedición del Acuse de Recibo de la Orden. (ii) Todos los pagos se harán dentro de los treinta (30) días siguientes a la fecha de la factura del Vendedor. (iii) El plazo para el pago es de la esencia del contrato. (iv) El Vendedor puede suspender el crédito al Comprador y puede retener el embarque de los Productos ordenados, suspender o cancelar su propio cumplimiento bajo estos Términos y Condiciones Estándar si, a su juicio exclusivo, la condición financiera del Comprador justifica dicha acción. La suspensión de su propio cumplimiento puede resultar en la reprogramación de los plazos por las demoras. (v) Los precios no incluyen los impuestos o derechos de aduana aplicables. El Comprador es el único responsable del pago de todos los impuestos y derechos de aduana aplicables. El Vendedor agregará impuestos al precio cuando así lo requiera la ley aplicable, y el Comprador pagará dichos impuestos en su totalidad, salvo que el Comprador le presente al Vendedor un certificado de exención tributaria debidamente otorgado, en una forma que sea satisfactoria para el Vendedor. Si bajo la ley aplicable se exige que el Comprador retenga los impuestos correspondientes al pago hecho al Vendedor, el Comprador remitirá en forma inmediata a la autoridad fiscal correspondiente el monto de dicha retención de impuestos y adoptará todas las medidas que sean razonables para minimizar dicha retención de impuestos. El Comprador adoptará todas las medidas requeridas para obtener y entregar en forma inmediata al Vendedor la certificación, correspondiente a dicha retención en una forma que sea satisfactoria para el Vendedor. (vi) El Comprador abonará todos los pagos vencidos bajo el Contrato en forma total sin ninguna deducción, ya sea ésta en la forma de un mecanismo de compensación, reconvención, descuento, rebaja o de otro modo. (vii) Todos los pagos pagaderos al Vendedor bajo el Contrato vencerán en forma inmediata a la terminación del Contrato salvo cualquier estipulación en contrario. (viii) Si el Comprador no cumple con pagar al Vendedor una suma vencida según el Contrato, el Comprador será responsable del pago de intereses al Vendedor que se devenguen sobre dicha suma desde la fecha de pago, a razón de una tasa de interés anual de 3% por encima del tipo de interés bancario del mercado de Londres (LIBOR) del Dólar Estadounidense de 12 meses, intereses que se devengarán en forma diaria hasta que se haga el pago, sea antes o después de una sentencia. En caso que la aplicación de dicha tasa de interés no sea procedente de acuerdo a la ley aplicable al lugar de ejecución del Contrato, se aplicará la tasa máxima que dicha ley permita.
5.
EMBARQUE, ENTREGA, TÍTULO Y RIESGO DE PÉRDIDA Los términos de entrega de los Productos son EXW (en el lugar designado por el Vendedor), según los Términos de Comercio Internacional (Incoterms 2000). El riesgo de pérdida o daños pasará al Comprador con la entrega realizada por el Vendedor al Comprador. El título de los Productos pasará al
Página 2 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
Comprador una vez que el Vendedor reciba el pago de fondos autorizados por las cantidades adeudadas con respecto al Contrato. El Vendedor puede hacer la entrega de los Productos mediante entregas parciales. Cada entrega parcial constituirá un Contrato separado y ninguna cancelación o terminación de un Contrato relacionado con una entrega parcial dará lugar al Comprador a rechazar o cancelar cualquier otro Contrato o entrega parcial. Se entiende que las fechas de entrega son estimadas y el tiempo y fecha de entrega no serán de la esencia del contrato en virtud de un aviso o de otro modo y dependen del pronto recibo por el Vendedor de toda la información y asistencia requeridas o solicitadas por el Vendedor para permitirle al Vendedor cumplir con sus obligaciones bajo el Contrato. El Vendedor no será responsable de los daños, pérdidas o gastos incurridos por el Comprador si el Vendedor no cumple con las fecha de entrega estimadas. En caso que los Productos no sean recogidos por el Comprador en la fecha efectiva de la entrega, el Vendedor podrá (a su juicio exclusivo) colocar los Productos en un almacén/bodega al costo y riesgo exclusivos del Comprador. 6.
FUERZA MAYOR El Vendedor se reserva el derecho de diferir la fecha de entrega de los Productos y/o la fecha de suministro de los Servicios, de cancelar el Contrato, o de reducir el volumen de los Productos y/o modificar los alcances de los Servicios ordenados por el Comprador (sin responsabilidad para el Comprador), si se encuentra impedido o se retrasa en el cumplimiento de sus obligaciones debido a circunstancias que escapan a su control, en la medida que sea razonable, incluyendo, pero sin limitarse a, los desastres naturales, fuerzas naturales, terremotos, maremotos, derrumbes, inundaciones, rayos, huracanes, tifones, tormentas u otras inclemencias del tiempo no incluidas en un planeamiento normal, epidemias y plagas; cambios de las leyes o regulaciones, acciones del gobierno; actos de la autoridad civil o militar; incendios, explosiones, paros patronales, huelgas y/o disputas laborales (sea que estén o no relacionadas con los trabajadores de cualquiera de las partes); conmoción civil; protestas; guerras; emergencia nacional; disturbios, insurrección civil; actos de terrorismo, restricciones o retrasos en el transporte, restricciones o retrasos en la fabricación e incapacidad del Vendedor de obtener los suministros adecuados o apropiados de las fuentes usuales; o actos del Comprador que tengan como consecuencia la impracticabilidad comercial. En el caso de dicho retraso, la fecha de entrega y/o cumplimiento será diferida por un plazo equivalente al tiempo perdido debido a dicho retraso.
7.
GARANTÍA El Vendedor garantiza que los Productos fabricados por el Vendedor, siempre que sean debidamente almacenados, encargados, instalados, usados y mantenidos, y los Servicios suministrados por el Vendedor, estarán libres de defectos relacionados con los materiales o la mano de obra. La obligación del Vendedor bajo esta garantía se limitará a reponer o reparar la parte o partes de los Productos, a la opción del Vendedor, cuyo defecto en los materiales o mano de obra sea demostrado dentro de los doce (12) meses desde la fecha de instalación o dieciocho (18) meses desde la fecha de entrega, lo que ocurra primero; o a volver a suministrar los Servicios dentro de los doce (12) meses desde el suministro de los Servicios (“PLAZO DE GARANTÍA”), siempre que el Comprador le dé al Vendedor pronto aviso de cualquier defecto y presente prueba sustancial y en una forma satisfactoria para el Vendedor (al juicio exclusivo de éste), incluyendo toda la información y documentación pertinentes necesarias para evaluar el rendimiento del pozo petrolero y equipo y las operaciones. Cualquier parte o partes defectuosas deben ser devueltas con el flete prepagado por el Comprador a un centro de servicios autorizado designado por el Vendedor para su inspección. El Vendedor enviará con el flete prepagado por el Comprador, productos en reposición de los Productos defectuosos, al destino de entrega indicado en la orden original. Los Productos devueltos al Vendedor por los cuales el Vendedor entregue productos en reposición bajo esta garantía se convertirán en propiedad del Vendedor. LA GARANTÍA PRECEDENTE REMPLAZA TODA OTRA GARANTÍA, SEA ÉSTA EN FORMA ORAL, ESCRITA, EXPRESA, TÁCITA O LEGAL, Y EL VENDEDOR NO OFRECE NINGUNA GARANTÍA DE ADECUACIÓN DE UN BIEN PARA EL DESTINO DE USO PARTICULAR QUE
Página 3 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
QUIERA DARLE EL COMPRADOR, NI GARANTÍA DE COMERCIABILIDAD. LAS OBLIGACIONES DE GARANTÍA DEL VENDEDOR Y LOS MEDIOS LEGALES DE PROTECCIÓN O REPARACIÓN DEL COMPRADOR SON ÚNICA Y EXCLUSIVAMENTE LOS QUE ESTÁN EXPRESAMENTE PREVISTOS EN EL PRESENTE CONTRATO. ADICIONALMENTE EL COMPRADOR RENUNCIA A CUALQUIER Y TODO TIPO DE RECLAMO RELACIONADO CON VICIOS OCULTOS Y VICIOS REDHIBITORIOS. NO SE PRORROGARÁ EL PLAZO DE GARANTÍA UNA VEZ QUE LAS PARTES O PRODUCTOS HAYAN SIDO REPARADOS U OBJETO DE REPOSICIÓN O QUE LOS SERVICIOS HAYAN SIDO VUELTOS A SUMINISTRAR. DICHAS PARTES O PRODUCTOS O SERVICIOS PERMANECERÁN BAJO LA GARANTÍA ÚNICAMENTE POR LA PORCIÓN NO CADUCADA DEL PLAZO DE GARANTÍA. LA ÚNICA RESPONSABILIDAD DEL VENDEDOR SERÁ, A SU OPCIÓN, REPARAR O REPONER LAS PARTES O PRODUCTOS O VOLVER A SUMINISTRAR LOS SERVICIOS BAJO ESTA CONDICIÓN. EL VENDEDOR PUEDE, A SU JUICIO EXCLUSIVO, ACREDITAR A LA CUENTA DEL COMPRADOR LA PORCIÓN DE DICHAS PARTES O PRODUCTOS Y/O SERVICIOS QUE EL VENDEDOR DETERMINE SON DEFECTUOSOS. La garantía precedente no se aplica a: (a) los defectos causados en todo o en parte por, o atribuidos a materiales abrasivos, corrosión debido a fluidos agresivos, rayos, suministro de voltaje inapropiado, manejo indebido o aplicación errada; (b) Productos o partes que son normalmente consumidos en operación, o que tienen una vida normal naturalmente más corta que el PLAZO DE GARANTÍA; (c) alteraciones o reparaciones llevadas a cabo sin la previa aprobación por escrito del Vendedor, o uso de equipo y accesorios para un fin distinto para el cual está destinado dicho equipo y accesorios; (d) instalaciones realizadas por el Comprador, salvo que los ingenieros del Comprador hayan sido entrenados y debidamente certificados por el Vendedor; (e) instalaciones en las que el Comprador no haya ejercitado las prácticas de aplicación de ingeniería para los Productos, según fueron aprobados por el Proveedor; (f) Productos o Servicios defectuosos, cuando el Comprador siga haciendo uso de los Productos luego de haber tomado conocimiento del defecto, o del momento en que el Comprador debió haber tomado conocimiento de dicho defecto, lo que ocurra primero en el tiempo; (g) defectos que surjan o tengan conexión con información, dibujos, interpretaciones de diagramas, especificaciones técnicas o instrucciones proporcionadas por el Comprador al Vendedor. 8.
LIMITACIÓN DE RESPONSABILIDAD (i) PARA LOS FINES DE ESTA CONDICIÓN 8(i), EL TÉRMINO “DAÑO CONSECUENCIAL” SIGNIFICARÁ (EN CADA CASO, SEA O NO PREVISIBLE A LA FECHA DEL CONTRATO): (a) LAS PÉRDIDAS Y/O DAÑOS MEDIATOS, INDIRECTOS, ESPECIALES, INCIDENTALES, PUNITIVOS Y/O ESPECIALES; (b) EL LUCRO CESANTE, LA PÉRDIDA O DIFERIMIENTO DE PRODUCCIÓN, PÉRDIDA DE PRODUCTO, PÉRDIDA DE REPUTACIÓN, PÉRDIDA DE USO, PÉRDIDA DE INGRESOS, UTILIDADES EFECTIVAS O ANTICIPADAS, COSTO DE CAPITAL, EN CADA CASO SEA EN FORMA DIRECTA O INDIRECTA, RECLAMACIONES POR INTERRUPCIÓN DE SERVICIO O FALLA EN EL SUMINISTRO, COSTOS Y GASTOS INCURRIDOS EN CONEXIÓN CON LOS COSTOS OPERATIVOS DE MANO DE OBRA, TRANSPORTE O FUENTES DE SUMINISTROS O INSTALACIONES SUSTITUTAS, MANO DE OBRA EMPLEADA EN CONEXIÓN CON EL RETIRO Y REPOSICIÓN DE PRODUCTOS DENTRO DEL POZO O CUALESQUIERA OTRAS PÉRDIDAS O DAÑOS INCURRIDOS COMO CONSECUENCIA O EN CONEXIÓN CON LA INTERRUPCIÓN DEL SERVICIO, EN CADA CASO. NO OBSTANTE DISPOSICIÓN EN CONTRARIO EN OTRA PARTE, EN NINGÚN CASO EL VENDEDOR SERÁ RESPONSABLE POR LOS DAÑOS CONSECUENCIALES Y EL COMPRADOR SERÁ RESPONSABLE Y LIBRARÁ, INDEMNIZARÁ, DEFENDERÁ Y MANTENDRÁ INDEMNE AL GRUPO DEL VENDEDOR FRENTE A LOS DAÑOS CONSECUENCIALES, AUN CUANDO FUERAN CAUSADOS POR LA NEGLIGENCIA O CULPA, SOLIDARIA, CONJUNTA, CONCURRENTE O PARCIAL
Página 4 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
DEL VENDEDOR, RESPONSABILIDAD OBJETIVA O RESPONSABILIDAD DEL FABRICANTE, Y SIN CONSIDERACIÓN DE LA FORMA DE ACCIÓN, SEA QUE SE TRATE DE RESPONSABILIDAD CONTRACTUAL, EXTRACONTRACTUAL (INCLUYENDO LA NEGLIGENCIA O CULPA), VIOLACIÓN DE GARANTÍA, INDEMNIZACIÓN, POR OPERACIÓN DE LA LEY, O DE OTRO MODO.
9.
(ii)
LA RESPONSABILIDAD TOTAL DEL VENDEDOR EN CUALQUIER ACCIÓN SEA POR RESPONSABILIDAD CONTRACTUAL, EXTRACONTRACTUAL (INCLUYENDO LA NEGLIGENCIA SOLIDARIA, CONJUNTA O CONCURRENTE), O QUE DE OTRO MODO SURJA, SE RELACIONE O RESULTE DE LA FABRICACIÓN, VENTA, ENTREGA, REVENTA, REPARACIÓN, REPOSICIÓN O USO DEL PRODUCTO, O DEL SUMINISTRO DEL SERVICIO, O DEL CUMPLIMIENTO O FALTA DE CUMPLIMIENTO DEL CONTRATO, NO EXCEDERÁ DEL PRECIO RECIBIDO POR EL VENDEDOR POR EL PRODUCTO O PARTE DEL MISMO, O DEL COSTO DE SUMINISTRO DE CUALQUIER TRABAJO DE SERVICIO QUE DÉ LUGAR A LA ACCIÓN AL EFECTO, EL GRUPO DEL COMPRADOR RENUNCIA A INICIAR CUALQUIER ACCIÓN EN CONTRA DEL GRUPO DEL VENDEDOR PARA PERSEGUIR CUALQUIER INDEMNIZACIÓN POR SOBRE LOS LÍMITES PACTADOS EN ESTA CONDICIÓN, Y SE OBLIGA A INDEMNIZAR, DEFENDER Y MANTENER AL GRUPO DEL VENDEDOR LIBRE DE Y POR CUALQUIER RESPONSABILIDAD QUE EXCEDA EL LÍMITE DE RESPONSABILIDAD PACTADO EN ESTA SECCIÓN, AÚN CUANDO LA MISMA SEA GENERADA A FAVOR DE CUALQUIER MIEMBRO DEL GRUPO DEL COMPRADOR, O DE SUS CONTRATISTAS, SUBCONTRATISTAS, OPERADORES Y/O EL DUEÑO DEL POZO (EL TÉRMINO “DUEÑO DE POZO” DEBERÁ INCLUIR PERSONAS O ENTIDADES CON CUALQUIER TIPO DE DERECHOS O INTERÉS SOBRE EL POZO Y/O INSTALACIONES), Y AÚN CUANDO ESTOS DAÑOS SEAN GENERADOS POR LA NEGLIGENCIA DEL GRUPO DEL COMPRADOR Y/O DEL GRUPO DEL VENDEDOR.
(iii)
EL COMPRADOR ENTIENDE Y ACUERDA QUE LAS LIMITACIONES A LA RESPONSABILIDAD PRECEDENTES SON PARTE ESENCIAL DEL CONTRATO Y QUE EN AUSENCIA DE DICHAS LIMITACIONES, LOS TÉRMINOS MATERIALES Y ECONÓMICOS DE ESTE CONTRATO SERÍAN ESENCIALMENTE DIFERENTES.
INDEMNIZACIÓN E INDEMNIDAD Todas las exclusiones e indemnidades estipuladas bajo esta Condición 9 (salvo por las previstas bajo las Condiciones 9.1(c) y 9.2(c)) y la Condición 8 (i), se aplicarán sin consideración de la causa y no obstante la negligencia, culpa o violación de obligaciones (sea por ley o de otro modo) de la parte indemnizada o de cualquier otra entidad o parte y se aplicarán sin consideración de si la acción fue de carácter contractual, extracontractual o, de otro modo, por operación de la ley. Para los propósitos de las Condiciones 9.1(c) y 9.2 (c), “tercero” significará cualquier parte que no sea miembro del Grupo del Comprador ni del Grupo del Vendedor. 9.1. El Vendedor será responsable y librará, indemnizará, defenderá y mantendrá indemne al Grupo del Comprador frente a cualquier acción, pérdida, daño, costo (incluyendo los costos legales), gasto y otras responsabilidades, con respecto a lo siguiente: (a) Sujeto a la condición 9.2(d), la pérdida o daño a la propiedad (distinta a los Productos luego de su entrega conforme con la Condición 5) del Grupo del Vendedor, sea que con respecto a ésta el Grupo del Vendedor sea el propietario, o la haya contratado, arrendado o que por el contrario haya sido provista por el Grupo del Vendedor como consecuencia o en relación con el cumplimiento del Contrato; (b) Los daños a personas, incluyendo la muerte o enfermedad de cualquier persona empleada por el Grupo del Vendedor, como consecuencia o vinculados al cumplimiento del Contrato; (c) Sujeto a la condición 9.3, los daños a terceros, incluyendo la muerte, enfermedad, pérdida o daños a la propiedad de un tercero, en la medida que dichos daños, pérdidas o daños sean causados por la
Página 5 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
negligencia, culpa o violación de obligaciones (sea por operación de la ley o de otro modo) del Grupo del Vendedor. 9.2. El Comprador será responsable y librará, indemnizará, defenderá y mantendrá indemne al Grupo del Vendedor frente a cualquier acción, pérdida, daño, costo (incluyendo los costos legales), gasto y otras responsabilidades, con respecto a lo siguiente: (a) Pérdidas o daños a la propiedad del Grupo del Comprador, ya sea:(i) que el Grupo del Comprador sea el propietario, o (ii) que la propiedad haya sido contratada, arrendada o que haya sido, provista por o para el Grupo del Comprador (incluyendo los Productos después de la entrega conforme con la Condición 5); y (b) Los daños a personas, incluyendo la muerte o enfermedad de cualquier persona empleada por el Grupo del Comprador, como consecuencia o en relación con el cumplimiento o falta de cumplimiento del Contrato; y (c) Sujeto a cualesquiera otras estipulaciones del Contrato, los daños a terceros, incluyendo la muerte, enfermedad, pérdida o daños a la propiedad de un tercero, en la medida que dichos daños, pérdidas o daños sean causados por negligencia, culpa o violación de obligaciones (sea por operación de la ley o de otro modo) del Grupo del Comprador; y (d) A la opción del Vendedor, la reparación, reposición o reembolso del costo total del equipo, herramientas y/o instrumentos del Vendedor debido a su pérdida o daño en el fondo del pozo del Comprador durante el suministro de los Servicios, o debido a su pérdida o daño por la abrasión o corrosión ocasionada por efluentes del pozo, salvo que dicha pérdida o daños se deba a la negligencia del Vendedor. 9.3. No obstante la Condición 9.1, el Comprador será responsable y defenderá, indemnizará y mantendrá indemne al Grupo del Vendedor frente a toda acción que sea consecuencia del cumplimiento o falta de cumplimiento del Contrato en relación con lo siguiente, y sea o no que resulte de o este relacionada con la negligencia del Grupo del Vendedor: (i) pérdidas o daños al pozo o perforación o a cualquier instalación de producción de petróleo y gas de terceros; (ii) percolación o contaminación del depósito que se origine en el subsuelo o que provenga de la propiedad del Comprador o tercero no obstante la causa como se origine; (iii) voladura, incendio, explosión, depresión topográfica de cualquier pozo o depósito o cualquier otra condición no controlada de un pozo (incluyendo los costos para controlar un pozo descontrolado y la remoción de escombros); (iv) daños o fuga del producto o sustancia de una instalación, incluyendo un oleoducto u otra instalación subterránea. 9.4. No obstante disposición en contrario del Contrato, el Comprador será responsable y librará, indemnizará, defenderá y mantendrá indemne al Grupo del Vendedor frente a cualquier acción, pérdida, daño, costo (incluyendo los costos legales), gasto y otras responsabilidades, con respecto a los actos u omisiones de los empleados o agentes del Grupo del Vendedor en conexión con el cumplimiento de los Servicios (o cualquier parte de los Servicios), cuando, conforme con el Contrato, los empleados del Grupo del Vendedor estén bajo la supervisión, dirección o control del Comprador con respecto a dichos Servicios o parte de dichos Servicios. 10. FALTA DE ENTREGA La cantidad de cualquier envío de Productos conforme el registro del Vendedor como despachados desde la sede de operaciones del Vendedor u otro lugar designado será prueba concluyente de la cantidad recibida por el Comprador, salvo que el Comprador pueda ofrecer prueba demostrando lo contrario. El Vendedor no será responsable de la falta de entrega de Productos (aun cuando fuera causada por la negligencia del Vendedor), salvo que el Comprador dé un aviso por escrito al Vendedor sobre la falta de entrega dentro de cuarenta y ocho (48) horas de la fecha y hora en que el Producto hubiera sido recibido en el curso normal de las operaciones. Cualquier responsabilidad del Vendedor por falta de entrega de los Productos se limitará, a juicio exclusivo del Vendedor, ya sea a la reposición de los Productos o a la emisión de una nota de crédito contra una factura expedida por los Productos. 11. VIOLACIÓN DE PATENTE Página 6 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
Si el Comprador es objeto de una reclamación o de otro modo toma conocimiento que un Producto o parte del mismo fabricado por el Vendedor infringe en forma real o presunta una patente u otro derecho de propiedad intelectual, el Comprador notificará de inmediato al Vendedor por escrito dándole información, asistencia y autoridad exclusiva para evaluar, defender y conciliar dicha acción o infracción potencial. El Vendedor entonces a su propio costo y opción: (a) conciliará dicha acción; (b) le facilitará al Comprador el derecho de usar dicho Producto; (c) lo repondrá o modificará para evitar la infracción; (d) lo retirará y reembolsará el precio de compra (incluyendo los costos de transportación e instalación), menos una cantidad razonable por concepto de depreciación; o (e) se defenderá ante dicha acción. 12. CANCELACIÓN Y CAMBIOS El Comprador no puede cancelar o reprogramar la fecha de entrega de los Productos y/o Servicios a ser provistos bajo el Contrato sin el previo consentimiento por escrito del Vendedor. En caso que el Vendedor dé dicho consentimiento, dicha cancelación o reprogramación con respecto a los Productos y/o Servicios por parte del Comprador dará lugar a un cobro al Comprador, el cual será determinado por el Vendedor. Todos los Productos especialmente diseñados o modificados que sean cancelados después del inicio de su fabricación serán objeto de un cargo por cancelación, el cual incluirá todos los costos y un margen razonable por el tiempo empleado, según lo determine el Vendedor. Los cargos de cancelación por accesorios y componentes abastecidos por terceros serán cobrados por el monto total del precio. El Vendedor, a su juicio exclusivo, ajustará el precio o las fechas de entrega, o hará las modificaciones que puedan requerirse como consecuencia de cualquier orden de cambio cuya expedición haya sido acordada por el Comprador y el Vendedor. No será válida la modificación de la orden de compra o Acuse de Recibo de la Orden u orden de cambio sino es aceptada por escrito por el Vendedor (a su juicio exclusivo). 13. RENUNCIA Cualquier renuncia por el Vendedor a una violación o incumplimiento de las obligaciones del Comprador bajo el Contrato, o cualquier omisión del Vendedor en ejercer los derechos que surjan bajo el Contrato, bajo ninguna circunstancia se interpretará como una renuncia a cualquier otra violación o incumplimiento posterior por parte del Comprador ni al derecho del Vendedor a ejercer sus derechos conforme el presente Contrato. En caso de cualquier incumplimiento por el Comprador, el Vendedor puede negarse a hacer más embarques. Si el Vendedor elige continuar haciendo entregas, la acción del Vendedor no constituirá una renuncia a dicho incumplimiento ni afectará los medios legales de protección o reparación del Vendedor por dicho incumplimiento. 14. TOTALIDAD DEL CONTRATO El Acuse de Recibo de la Orden, las Condiciones Especiales y estos Términos y Condiciones Estándar constituyen la totalidad del contrato entre las partes con respecto a la venta de los Productos y/o Servicios y revoca todas las comunicaciones, representaciones o acuerdos, previos sean orales o escritos, con respecto al objeto del presente. Las representaciones o declaraciones previas, relacionadas con la venta de los Productos y/o Servicios, formuladas por un representante del Vendedor, que no estén contenidas en el presente, no serán vinculantes para el Vendedor. 15. CONTROL DE EXPORTACIONES El Comprador acepta que, salvo que se obtenga previa autorización del Departamento de Comercio de EE.UU., ni el Comprador ni sus subsidiarias exportarán, reexportarán o pondrán en circulación, directa o indirectamente, ningún Producto recibido del Vendedor, a ningún país o destino al cual esté prohibida la exportación, reexportación o puesta en circulación de la tecnología o Producto por las Regulaciones de la Administración de Exportación del Departamento de Comercio de EE.UU. (“EAR”, por sus siglas en inglés), o esté prohibido por las leyes de los EE.UU. o por leyes que no sean de los EE.UU. que sean aplicables. El Comprador será responsable de obtener la licencia de exportación u otra documentación que sea necesaria antes de la exportación o reexportación de los Productos adquiridos del Vendedor bajo el Contrato. Asimismo, el Comprador dará un aviso sobre la necesidad de cumplir con dichas leyes y Página 7 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
regulaciones a cualquier persona, firma o entidad que tenga razón para creer que obtendrá dichos Productos del Comprador con la intención de exportarlos. Cada parte obtendrá, a su propio costo, las licencias y documentos de exportación e importación que sean necesarios para cumplir con sus obligaciones bajo el Contrato. Si no se pueden obtener las aprobaciones, el Vendedor podrá dar por terminado, cancelado o por el contrario quedará exonerado del cumplimiento de las obligaciones que pueda tener bajo el Contrato. Cualquier clasificación de exportación hecha por el Vendedor será sólo para el uso interno del Vendedor y no se interpretará como una representación o garantía con respecto a la debida clasificación de exportación de cada Producto o si se necesita una licencia de exportación u otra documentación para la exportación del Producto. Esta Condición 15 sobrevivirá a la terminación del Contrato. 16. ÉTICA COMERCIAL Ni el Vendedor ni el Comprador harán pagos ni tomarán ninguna acción que pudiera ser interpretada como dirigida al pago de dinero u otro artículo de valor en favor de un funcionario gubernamental, partido político o candidato de un partido político para los fines de influenciar los actos o inducir a un funcionario gubernamental para que haga uso de sus influencias para asistir en la obtención o retención de negocios en un país, en una forma que sea ilegal o que sujete al Vendedor a sanciones de carácter civil o penal, o que sean incompatibles con la Política de Ética Comercial del Vendedor. 17. CESIÓN El Vendedor podrá dar en cesión el Contrato o cualquier parte del mismo a cualquier persona, firma o empresa. El Comprador no tendrá derecho a dar en cesión el Contrato ni ninguna parte del mismo sin el previo consentimiento por escrito del Vendedor. 18. ARBITRAJE Cualquier disputa que surja o tenga relación con el Contrato, incluyendo una disputa en cuanto a la validez de los Términos y Condiciones Estándar y de esta Condición 18, será resuelta mediante arbitraje en Houston realizado en español por un solo árbitro, de conformidad con las Reglas del Tribunal Internacional de Arbitraje de Londres o LCIA, siglas en inglés de “The London Court of International Arbitration”). 19. LEY APLICABLE Estos Términos y Condiciones Estándar se interpretarán para todos los efectos y se les dará efecto legal de conformidad con las leyes de [país del Vendedor], no obstante los principios de conflicto de leyes. No será aplicable la Convención de las Naciones Unidas sobre los Contratos para la Venta Internacional de Mercaderías. 20. ESTIPULACIONES VARIAS Todas las muestras, dibujos, materiales descriptivos, especificaciones y publicidad proporcionados por el Vendedor y las descripciones o ilustraciones contenidas en los catálogos o folletos del Vendedor son publicados o emitidos con el único fin de dar una idea aproximada de los Productos y/o Servicios descritos en los mismos. Éstos no formarán parte del Contrato. A su propio costo, el Comprador obtendrá los permisos o cualquier otra autorización (incluyendo, con carácter enunciativo pero no limitativo, los permisos de trabajos y visas para empleados del Vendedor), los cuales pueden ser requeridos para permitirle al Vendedor cumplir con los Servicios. El Comprador acepta indemnizar al Vendedor frente los costos, reclamaciones, acciones, demandas o gastos incurridos o sufridos en conexión con el incumplimiento del Comprador en obtener los permisos o autorizaciones requeridos para cumplir con los Servicios. Si una corte, tribunal u organismo administrativo de jurisdicción competente encontrara que una estipulación del Contrato es en todo o en parte ilegal, inválida, nula, anulable, inejecutable o irrazonable, en la medida de dicha ilegalidad, invalidez, nulidad, anulabilidad, inejecutabilidad o irrazonabilidad, la estipulación se considerará divisible, y el resto de las estipulaciones del Contrato, como el resto de dicha estipulación, continuarán en pleno efecto y vigor.
Página 8 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
Estos Términos y Condiciones Estándar están sujetos a cambio sin previo aviso por escrito, en cualquier momento y cuando convenga, a juicio exclusivo del Vendedor. Todas las comunicaciones entre las partes acerca del Contrato se harán por escrito y se entregarán en forma personal o se enviarán por fax a la oficina registrada o a cualquier otra dirección según sea notificado a la otra parte. Las comunicaciones entregadas en forma personal se considerarán recibidas el día de la entrega o, si son enviadas por fax, el día hábil y a la hora de la transmisión, o por el contrario, el siguiente día hábil.
Página 9 de 9 Clean (2)
WG ESP- Términos y Condiciones de Venta Estandar Internacional (0 3)
Wood Group ESP, Inc. North American Operations Wood Group ESP Corporate Headquarters & Operations 5500 S.E.59th St.(73135) P.O. Box 15070 (73155) Oklahoma City, OK USA Telephone: (405) 670-1431 (800) 723-3771 Facsimile: (405) 670-5463 E-mail:
[email protected] www.woodgroup-esp.com
Corporate Sales Office 19416 Park Row, Suite 100 Houston,TX 77084 USA Telephone:(281) 492-5100 Facsimile: (281) 492-8107
Wood Group ESP Sales and Service Locations
Canada Wood Group ESP (Canada) Ltd Bay 6, 360 Aquaduct Dr. Brooks, Alberta T1R 1E4 Canada Telephone: (403) 501-5822 Facsimile: (403) 501-5823 Wood Group ESP (Canada) Ltd 300,1015-4th St. SW Calgary, Alberta T2R 1J4 Canada Telephone: (403) 263-7166 Facsimile: (403) 263-7211 Wood Group ESP (Canada) Ltd 3917 81 Avenue Leduc, Alberta T9E 8S6 Canada Telephone: (780) 955-2165 (888) 586-8909 Facsimile: (780) 955-9487 Colorado 410 17th Street, Suite 1260 Denver, CO 80202 USA Telephone: (303) 350-2111 (800) 535-0310 Facsimile: (303) 350-2112
New Mexico 509 Commerce Rd. Artesia, NM 88210 USA Telephone: (505) 746-4614 Facsimile: (505)746-4519 8426 North Dal Paso Hobbs, NM 88242 USA Telephone: (505) 392-7999 Facsimile: (505) 391-8190 Oklahoma 5500 S.E.59th St.(73135) P.O. Box 15070 (73155) Oklahoma City, OK USA Telephone: (405) 670-1431 (800) 723-3771 Facsimile: (405) 670-5463 1739 Hardcastle Ind. Blvd. P.O. Box 1680 Purcell, OK 73080 USA Telephone: (405) 527-1566 (800) 256-5058 Facsimile: (405) 527-7161
19416 Park Row, Suite 100 Houston,TX 77084 USA Telephone: (281) 492-5100 Facsimile: (281) 492-8107 2707 S.County Rd.1208 (79706) P.O. Box 80130 (79708) Midland, TX USA Telephone: (432) 699-7401 (800) 749-7402 Facsimile: (432) 699-4159 2507 25th St. (79549) P.O. Box 916 (79550) Snyder, TX USA Telephone: (325) 573-8101 Facsimile: (325) 573-1616 Wyoming 1845 N. Oilfield Center Casper, WY 82604 Telephone: (307) 234-4495 (800) 535-0306 Facsimile: (307) 234-4497
Mississippi 45 Jerry Doggett Dr. Laurel, MS 39443 USA Telephone: (601) 649-2030 (800) 488-9260 Facsimile: (601) 649-8819 Wood Group ESP, Inc.
Texas 1700 S.W. Mustang Dr. P.O. Box 947 Andrews, TX 79714 USA Telephone: (432) 523-9701 Facsimile: (432) 523-9700
The ESP Specialists
Product Catalog - Facilities - Copyright Wood Group ESP, Inc. – October 2009
www.woodgroup-esp.com revised October, 2009
Page-1
Wood Group ESP, Inc. Wood Group ESP International Operations ASIA PACIFIC Indonesia PT ESP Mulia Indonesia Balai Raja Industrial Park JL. Raya, DuriPekanbaru Road, KM 11 Duri, Riau Province, Sumatra 28884 Telephone:+62-765-561904 Facsimile: +62-765-561923 PT Indobornusa Mandiri Wisma Staco 6th Floor Jl.Casablanca Kav.18 Jakarta, Indonesia 12870 Telephone: +62 (21) 8370-2455 Facsimile: +62 (21) 831-2345 Singapore PTE Ltd. Shaw Tower #28-09 100 Beach Road Singapore, 189702 Telephone: +65-6396-3626 Facsimile: +65-6396-5362 EUROPE / AFRICA Africa EDGO-Trading TChad 1033, Rue de la Gendarmerie BP 5496, N’Djamena, Tchad Telephone: +235 524 757 +44 20707 42974 +44 20707 41777 Facsimile: +235 524 757 United Kingdom Maersk House, Greenbank Rd East Tullos, Aberdeen AB12 3BR Scotland Telephone: +44-1224-21 6636 Facsimile: +44-1224-21 6770
LATIN AMERICA Argentina Reconquista 1016 Piso 6 Buenos Aires, 1003 Argentina Telephone:+54-11-4-311-9411 Facsimile: +54-11-4-311-2980 Dalle Mura 150 Comodoro Rividavia Chubut 9000 Argentina Telephone:+54-297-446-8254 Facsimile: +54-297-447-8377 Brazil 65 Rua Antonio Vita Jardim Vonfiglioli CEP- 05593-080 Sao Paulo , Brazil Telephone:+55-11-3731-2999 Facsimile: +55-11-3731-2998 Colombia Wood Group Colombia, Colombser SA Carrera 11A #93-97 Office 204 Bogota, Colombia, Sur America Telephone:+57-1-621-2424 Facsimile: +57-1-621-2275 Ecuador Panamericana Norte Km. 12 1/2 entre pasaje Alfonso Moncayo y calle El Arenal, Parque Delta Quito Ecuador Telephone:+593-2-2428-211 Facsimile: +593-2-2428-213 Venezuela Avenidad Cuatricentenario Barinas Sede De La Toyota Barinas, EdoBarinos, Venezuela Codigo Postal 5201 Telephone:+58-273-546-1241 Facsimile: +58-273-546-2653
England Telephone: +44-1564-77-1739 Facsimile: +44-1564-77-1739
Av Intercomunal antigua sede Motoriente, El Tigre - Tigrito Edo Anzoategui, Venezuela Telephone:+58-283-241-7151 Facsimile: +58-283-241-8613
Wood Group ESP, Inc.
The ESP Specialists
Venezuela -continued Zona Industrial Segunda Km 6 ½ via a Perija Sector El Callao, Municipio San Francisco Maracaibo, Edo Zulia, Venezuela 4001 Telephone:+58-261-200-9200 Facsimile: +58-261-736-1993 MIDDLE EAST Dubai Oilfield Supply Center Ltd. Jebel Ali Free Zone Building No.50 P.O. Box 18131 Dubai, United Arab Emirates Telephone:+971-4-883-7595 Facsimile: +971-4-883-7579 Kuwait c/o Klalid Y. Al Fulaij Est. P.O. Box 22414 Safat 13085 Kuwait Telephone:(965)398-3639-2810 Facsimile: (965)398-3639 2811 Oman c/o Oman Oilfield Supply Center P.O. Box 104 Shati Al Qurum, Sultanate of Oman Telephone: +968-605501, 691091 Facsimile: +968-605784 RUSSIA Moscow #8 Leningradsky Prospect Office #4012-4015 Moscow, Russia 125040 Telephone: +7-502-937-6641 Facsimile: +7-502-937-6642 Wood Group ESP Service, Ltd #5 Kuzovatkin Street Nizhnevartovsk, Tyumen Region 628606 Telephone: +7 3466-416-195 Facsimile: +7 3466-416-295 www.woodgroup-esp.com
Page-2
revised October, 2009
Product Catalog - Facilities - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TA-1200 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 3.375” / 85.8 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 6
BEP
20
0.8
80%
15
0.6
60%
10
0.4
40%
5
0.2
20%
0.0
0%
4 Efficiency
2
Power
0 BPD 0 M3/DAY
200
400 50
600
800
1000
100
150
1200
1400
200
1600
1800
250
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-1200 60 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. Pump Performance Curve for TA-1200 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
15
Pump O.D.* 3.375” / 85.8 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
1.1
90%
4
1.0
80%
3.5
0.9
70%
3
0.8
60%
2.5
0.6
50%
2
0.5
40%
1.5
0.4
30%
1
0.3
20%
0.5
0.1
10%
4.5 Head
10
RECOMMENDED OPERATING RANGE
Efficiency
5
Power 0.0 250
0 M3/DAY BPD
0
50 250
100 500
150 750
1000
200 1250
0%
1500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-1200 50 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-14
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TA-1200 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10
Feet 2.1 3.5 4.9 6.3 7.8 9.1 10.5 11.9 13.3 14.8
Meters 0.64 1.07 1.49 1.92 2.38 2.77 3.20 3.63 4.05 4.51
Weight Lbs. 35 57 81 104 128 152 174 193 221 244
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 15.9 25.9 36.7 47.2 58.1 68.9 78.9 87.5 100.2 110.7
Stgs. 13 27 45 61 77 93 108 124 140 156
Part No. 912667 912675 912683 912691 912709 912717 912725 912733 912741 912758
Compression Stgs.
Part No.
Floater Stgs.
Compression
Part No. Stgs. Part No.
70
Length Feet Meters
Weight Lbs. Kgs.
0.5 0.25 0.18 0.18
10 0.4 0.18 0.18
0.15 0.08 0.05 0.05
ABRASION RESISTANT PUMP
86
113732
145
113735
STANDARD PUMP Part No.
4.5 0.18 0.08 0.08
113552
AR PUMP Part No.
1021310 912022 914341 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-15
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TA-1200 1 stage, S.G. = 1
Head M Ft
12
40
RECOMMENDED OPERATING RANGE
85 Hz
80 Hz
35 10
75 Hz 30 70 Hz
8 25
6
65 Hz 60 Hz
20
55 Hz 50 Hz
15 4
45 Hz 10
2 5
0 BPD M3/DAY
0
500
1000 100
1500 200
2000 300
CAPACITY
Wood Group ESP, Inc. Page-16
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TA-1500 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 3.375” / 85.8 mm
BEP
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
Head RECOMMENDED OPERATING RANGE
15
1.5
75%
10
1.0
50%
0.5
25%
4
Efficiency 2 5
Power 0 BPD 0 M3/DAY
200
400
600
50
100
800
1000 150
1200
1400
200
1600 250
1800
2000
300
2200 350
2400
2600
0.0 2800
0%
400
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-1500 60 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-17
Wood Group ESP, Inc. Pump Performance Curve for TA-1500 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 3.375” / 85.8 mm
4
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
1.0
80%
3.5
0.9
70%
3
0.8
60%
2.5
0.6
50%
2
0.5
40%
1.5
0.4
30%
1
0.3
20%
0.5
0.1
10%
0.0
0%
10
Head
RECOMMENDED OPERATING RANGE
Efficiency
5
Power 0 M3/DAY BPD
0
50 250
100 500
150 750
1000
200 1250
250 1500
300 1750
350 2000
2250
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-1500 50 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-18
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TA-1500 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10
Feet 2.1 3.5 4.9 6.3 7.8 9.1 10.5 11.9 13.3 14.8
Meters 0.64 1.07 1.49 1.92 2.38 2.77 3.20 3.63 4.05 4.51
Weight Lbs. 38 65 91 118 145 172 198 226 252 279
Floater
Kgs. 17.2 29.5 41.3 53.5 65.8 78.0 89.8 102.5 114.3 126.6
Stgs. 10 23 35 48 60 73 85 96 110 123
Length Feet Meters Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
0.5 0.2 0.2 0.2
0.15 0.06 0.06 0.06
Part No. 912766 912774 912782 912790 912808 912816 912824 912832 912840 912857
Compression Stgs.
Weight Lbs. Kgs. 10 0.4 0.18 0.18
ABRASION RESISTANT PUMP
Part No.
Floater Stgs. 9 21 32 45 56 68 79 91 103 114
STANDARD PUMP Part No.
4.5 0.18 0.08 0.08
Compression
Part No. Stgs. Part No. 140601 140602 140603 140604 140605 140606 140607 140608 140609 140610
AR PUMP Part No.
1021310 120556 934182 120556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-19
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TA-1500 1 stage, S.G. = 1
Head M Ft 12
85 Hz
RECOMMENDED OPERATING RANGE
35 80 Hz
10 30
75 Hz
8
70 Hz
25
65 Hz 6
20
60 Hz 55 Hz
15 50 Hz
4
45 Hz 10 2 5
0 BPD M3/DAY
0
500
1000 100
1500 200
2000 300
2500 400
3000
CAPACITY
Wood Group ESP, Inc. Page-20
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TA-400 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 3.375” / 85.8 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head
RECOMMENDED OPERATING RANGE 6
20
1.0
80%
15
0.8
60%
10
0.5
40%
0.3
20%
4
2 Efficiency 5
Power 0 BPD 0
100
200 25
M3/DAY
300
400
50
500 75
0.0 700
600
0%
100
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-400 60 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TA-400 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 3.375” / 85.8 mm
Qmin
4.5
0.2
90%
4
0.2
80%
3.5
0.2
70%
3
0.2
60%
2.5
0.1
50%
2
0.1
40%
0.1
30%
0.1
20%
0.0
10%
0.0
0%
10
5
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 15
BEP
Efficiency
1.5
1 Power 0.5
0 M3/DAY BPD
0
10 50
20 100
30 150
40
200
250
50 300
60 350
70 400
450
80 500
90 550
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-400 50 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TA-400 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10
Feet 2.1 3.5 4.9 6.3 7.8 9.1 10.5 11.9 13.3 14.7
Meters 0.64 1.07 1.49 1.92 2.38 2.77 3.20 3.63 4.05 4.48
Weight Lbs. 34 55 75 96 118 139 160 181 202 223
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 15.4 24.9 34.0 43.5 53.5 63.0 72.6 82.1 91.6 101.2
Stgs. 16 35 54 74 93 112 132 151
Part No. 917378 917385 917393 917401 917419 917427 917435 917443
Compression Stgs.
Length Feet Meters
Weight Lbs. Kgs.
0.5 0.25 0.18 0.18
10 0.4 0.18 0.18
0.15 0.08 0.05 0.05
ABRASION RESISTANT PUMP
Part No.
Floater Stgs. 15 33 50 69 86 104 122 139 157 174
STANDARD PUMP Part No.
4.5 0.18 0.08 0.08
Compression
Part No. Stgs. Part No. 113871 15 113981 113872 33 113982 113873 50 113983 113874 69 113984 113875 86 113985 113876 113877 113878 113879 113880
AR PUMP Part No.
1021310 912022 914341 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TA-400 1 stage, S.G. = 1
Head M Ft
85 Hz 14
RECOMMENDED OPERATING RANGE
45 80 Hz
12
40 75 Hz 35 70 Hz
10 30 8
6
65 Hz
25
60 Hz 55 Hz
20
50 Hz 15
45 Hz
4 10 2 5
0 BPD M3/DAY
0
100
200 25
300 50
400
500 75
600
700 100
800 125
900
CAPACITY
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TA-550 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 3.375” / 85.8 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 30
0.6
60%
0.5
50%
20
0.4
40%
15
0.3
30%
0.2
20%
0.1
10%
8 25
6
Head
4 Efficiency 10
2 5 Power
0 BPD 0 M3/DAY
100
200
300
25
400
500
50
75
600
700
100
0.0 900
800
0%
125
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-550 60 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TA-550 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
15
Pump O.D.* 3.375” / 85.8 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 4.5
0.2
90%
4
0.2
80%
3.5
0.2
70%
3
0.2
60%
0.1
50%
2
0.1
40%
1.5
0.1
30%
0.1
20%
0.0
10%
10
2.5 Efficiency
5
1
Power
0.5
0 M3/DAY BPD
0
25 100
50 200
300
75 400
0.0 125
100 500
600
0%
700
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-550 50 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TA-550 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10
Feet 2.1 3.5 4.9 6.3 7.8 9.1 10.5 11.9 13.3 14.8
Meters 0.64 1.07 1.49 1.92 2.38 2.77 3.20 3.63 4.05 4.51
Weight Lbs. 38 63 88 107 141 167 193 219 245 271
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 17.2 28.6 39.9 48.5 64.0 75.8 87.5 99.3 111.1 122.9
Stgs. 16 35 54 74 93 112 132 151 170 190
Part No. 912873 912881 912899 912907 912915 912923 912931 912949 912956 912964
Compression Stgs.
Length Feet Meters
Weight Lbs. Kgs.
0.5 0.25 0.18 0.18
10 0.4 0.18 0.18
0.15 0.08 0.05 0.05
ABRASION RESISTANT PUMP
Part No.
Floater Stgs. 15 33 50 69 86 104 122 139 157 174
STANDARD PUMP Part No.
4.5 0.18 0.08 0.08
Compression
Part No. Stgs. Part No. 113961 15 103140 113962 33 103141 113963 50 103142 113964 59 103143 113965 86 103144 113966 113967 113968 113969 113970
AR PUMP Part No.
1021310 912022 914341 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TA-550 1 stage, S.G. = 1
Head M Ft 16 50
RECOMMENDED OPERATING RANGE
85 Hz 80 Hz 12
40 75 Hz 70 Hz 30 65 Hz
8 60 Hz 55 Hz
20
50 Hz 45 Hz
4 10
0 BPD M3/DAY
0
200
400
600 100
50
800
1000 150
CAPACITY
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TA-900 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 3.375” / 85.8 mm
Qmin
BEP
RECOMMENDED OPERATING RANGE
Head 6
HP PMP MTR ONLY LOAD EFF
Qmax
20
0.4
80%
15
0.3
60%
0.2
40%
0.1
20%
4
Efficiency
10
2 5 Power
0 BPD 0 M3/DAY
100
200 25
300
400
50
500 75
600
700
100
800 125
900 150
1000
1100
1200
175
1300 200
1400
0.0 1500
0%
225
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-900 60 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. Pump Performance Curve for TA-900 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
15
Pump O.D.* 3.375” / 85.8 mm
4.5
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
0.2
90%
4
0.2
80%
3.5
0.2
70%
3
0.2
60%
0.1
50%
0.1
40%
0.1
30%
1
0.1
20%
0.5
0.0
10%
10
Head
RECOMMENDED OPERATING RANGE
2.5 Efficiency 2
5
1.5
Power
0 M3/DAY BPD
0
25 100
50 200
300
75 400
500
100 600
125 700
800
150 900
0.0 200
175 1000
1100
0%
1200
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TA-900 50 HZ 4-1/2 IN ROTATIONAL DIRECTION 114.3 MM 3-3/8 IN SHAFT DIAMETER 85.73MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-10
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TA-900 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10
Feet 2.1 3.5 4.9 6.3 7.8 9.1 10.5 11.9 13.3 14.8
Meters 0.64 1.07 1.49 1.92 2.38 2.77 3.20 3.63 4.05 4.51
Weight Lbs. 38 63 88 107 141 167 193 219 245 271
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 17.2 28.6 39.9 48.5 64.0 75.8 87.5 99.3 111.1 122.9
Stgs. 16 35 54 74 93 112 132 151 170 190
Part No. 914499 912576 912584 912592 912618 912618 912626 912634 912642 912659
Compression Stgs.
Length Feet Meters
Weight Lbs. Kgs.
0.5 0.25 0.18 0.18
10 0.4 0.18 0.18
0.15 0.08 0.05 0.05
ABRASION RESISTANT PUMP
Part No.
Floater Stgs. 15 33 50 69 86 104 122 139 157 174
STANDARD PUMP Part No.
4.5 0.18 0.08 0.08
Compression
Part No. Stgs. Part No. 140551 15 103149 140552 33 103150 140553 50 103151 140554 69 103152 140555 86 103153 140556 140557 140558 140559 140560
AR PUMP Part No.
1021310 912022 914341 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TA-900 1 stage, S.G. = 1
Head M Ft
RECOMMENDED OPERATING RANGE
85 Hz 12
40 80 Hz 35 75 Hz
10 30
70 Hz 8
65 Hz
25
60 Hz 6
20 55 Hz 50 Hz
15 4
45 Hz 10
2 5
0 BPD M3/DAY
0
200
400 50
600 100
800
1000 150
1200
1400 200
1600 250
CAPACITY
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-1250 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
Head
35
HP PMP MTR ONLY LOAD EFF 1.8 70%
Qmax
RECOMMENDED OPERATING RANGE
10 30
1.5
60%
25
1.3
50%
20
1.0
40%
15
0.8
30%
10
0.5
20%
0.3
10%
8
Efficiency 6
4
2 Power
5
0 BPD 0 M3/DAY
250
500
50
750 100
1000
1250
150
1500
200
250
0.0 2000
1750
0%
300
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-1250 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-21
Wood Group ESP, Inc. Pump Performance Curve for TD-1250 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head RECOMMENDED OPERATING RANGE
20
7
0.9
70%
6
0.8
60%
5
0.6
50%
0.5
40%
3
0.4
30%
2
0.3
20%
0.1
10%
15 4 Efficiency
10
5 Power
1
0 M3/DAY BPD
0
25 100
200
50 300
75 400
100
500
600
125 700
800
150 900
175
1000 1100
200 1200
0.0 250
225
1300
1400
0%
1500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-1250 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-22
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-1250 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5
Stgs. 14 30 47 63 79 95 111 128 144 160 176 192
Part No. 192421 192422 192423 192424 192425 192426 192427 192428 192429 192430 192431 192432
Compression Stgs. 13 29 45 62 78 94
Length Feet Meters
Weight Lbs. Kgs.
0.3 0.21 0.2 0.21
10 0.77 0.5 0.5
0.09 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 192381 192382 192383 192384 192385 192386
Floater Stgs. 13 29 43 58 73 87 102 117 131 146 161 175
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 192391 12 192411 192392 27 192412 192393 41 192413 192394 56 192414 192395 71 192415 192396 87 192416 192397 192398 192399 192400 192401 192402
AR PUMP Part No.
930941 934232 934182 120556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-23
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-1250 1 stage, S.G. = 1
Head M Ft 24
RECOMMENDED OPERATING RANGE
70
85 Hz
20 80 Hz
60
75 Hz 16 50 70 Hz 65 Hz 12
40 60 Hz 55 Hz
30 8
50 Hz 45 Hz
20 4 10
0 BPD M3/DAY
0
500
1000 100
1500 200
2000
2500
300
CAPACITY
Wood Group ESP, Inc. Page-24
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-150 1 stage @ 3500 RPM, S.G. = 1 Head Pump O.D.* 4” / 101.6 mm Qmin M Ft
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
8
0.5
50%
20
0.4
40%
15
0.3
30%
10
0.2
20%
5
0.1
10%
25 Head
6
4
Efficiency
2
Power
0 BPD 0 M3/DAY
50
100 10
150
200
20
30
250 40
0.0 350
300
0%
50
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-150 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1/2 IN 12.69MM 60 HZ 44 HP 70 HP 90 HP
50 HZ 37 HP 58 HP 75 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TD-150 1 stage @ 2917 RPM, S.G. = 1 Head Pump O.D.* 4” / 102 mm Qmin Ft M
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 5
0.3
50%
4
0.2
40%
3
0.2
30%
0.1
20%
0.1
10%
0.0
0%
15
10
Efficiency
2
5
1 Power
0 M3/DAY BPD
0
10 50
20 100
30 150
40 200
250
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-150 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1/2 IN 12.69MM 60 HZ 44 HP 70 HP 90 HP
50 HZ 37 HP 58 HP 75 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-150 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.9 171.5
Stgs. 19 40 60 81 102 122 143 164 184 205 226 247
Part No. 150701 150702 150703 150704 150705 150706 150707 150708 150709 150710 150711 150712
Compression Stgs. 19 40 60 81
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.23 0.19 0.19
10 0.77 0.72 0.72
0.18 0.07 0.07 0.07
ABRASION RESISTANT PUMP
Part No. 150691 150692 150693 150694
Floater Stgs. 17 35 54 73 93 111 131 149 169 187 207 225
STANDARD PUMP Part No.
4.5 0.35 0.33 0.33
Compression
Part No. Stgs. Part No. 170791 170792 170793 170794 170795 170796 170797 170798 170799 170612 170801 170802
AR PUMP Part No.
930941 100572 1008556 1008556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-150 1 stage, S.G. = 1
Head M Ft
85 Hz 14
RECOMMENDED OPERATING RANGE
45 80 Hz
12
40 75 Hz 35
10
70 Hz 30
8
6
65 Hz
25
60 Hz 55 Hz
20
50 Hz 15
45 Hz
4 10 2 5
0 BPD M3/DAY
0
50
100 10
150 20
200 30
250 40
300 50
350
400 60
450 70
500
CAPACITY
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-1750 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 1.8
70%
1.5
60%
1.3
50%
20
1.0
40%
15
0.8
30%
10
0.5
20%
0.3
10%
35 10 30 Head 8 25
Efficiency 6
4
2 5
Power
0 BPD 0 M3/DAY
200
400 50
600
800
100
1000 150
1200
1400
200
1600
1800
250
300
2000
2200
2400
350
2600 400
2800
0.0 3000
0%
450
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-1750 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-25
Wood Group ESP, Inc. Pump Performance Curve for TD-1750 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 101.6 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head
20
BEP
6
0.8
75%
5
0.6
63%
0.5
50%
3
0.4
38%
2
0.3
25%
0.1
13%
15
4
10
Efficiency
5 1
Power
0 M3/DAY BPD
0
50 250
100 500
150 750
1000
200 1250
250 1500
300 1750
0.0 400
350 2000
2250
0%
2500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-1750 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-26
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-1750 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378 408 438 468
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5 185.1 198.7 212.3
Stgs. 8 16 25 33 41 50 58 67 75 84 92 100 108 116 125
Part No. 939801 939819 939827 939835 939868 939876 939884 939892 939900 939918 939926 939934 939942 939959 939967
Compression Stgs. 7 15 24 32 41 49 57 66 74 83 91 100
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.21 0.2 0.21
10 0.77 0.5 0.5
0.18 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 130181 130182 130183 130184 130185 130186 130187 130188 130189 130190 130191 130192
Floater Stgs. 8 16 25 33 41 50 58 67 75 84 92 100 108 116 125
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 110651 7 130201 110652 15 130202 110653 24 130203 110654 32 130204 110655 41 130205 110656 49 130206 110657 57 130207 110658 66 130208 110659 74 130209 110660 83 130210 110661 91 130211 110662 100 130212 110663 110664 110665
AR PUMP Part No.
930941 934232 934182 120556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-27
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-1750 1 stage, S.G. = 1
Head M Ft
85 Hz RECOMMENDED OPERATING RANGE
16 50
80 Hz 75 Hz
12
40
70 Hz 65 Hz
30
60 Hz
8
55 Hz 50 Hz
20
45 Hz 4 10
0 BPD M3/DAY
0
500
1000 100
1500 200
2000 300
2500 400
3000 500
CAPACITY
Wood Group ESP, Inc. Page-28
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-2200 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 102 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 1.8
70%
30
1.5
60%
25
1.3
50%
20
1.0
40%
15
0.8
30%
10
0.5
20%
0.3
10%
35 10
Head
8 Efficiency
6
4
Power 2 5
0 BPD 0 M3/DAY
500
1000
100
1500 200
2000
2500
300
3000
400
500
0.0 4000
3500
0%
600
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-2200 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-29
Wood Group ESP, Inc. Pump Performance Curve for TD-2200 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 102 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head
20
BEP
7
0.9
88%
6
0.8
75%
5
0.6
63%
4
0.5
50%
3
0.4
38%
2
0.3
25%
0.1
13%
15
Efficiency 10
5 Power 1
0 M3/DAY BPD
0
50 250
100 500
750
150 1000
200 1250
250 1500
300 1750
350 2000
2250
400 2500
450 2750
500 3000
0.0 550
0%
3250
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-2200 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 11/16 IN 17.46MM 60 HZ 125 HP 200 HP 255 HP
50 HZ 104 HP 167 HP 213 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-30
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-2200 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378 408 438 468
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5 185.1 198.7 212.3
Stgs. 8 16 25 33 41 50 58 67 75 84 92 100 108 116 125
Part No. 130981 130982 130983 130984 130985 130986 130987 130988 130989 130990 130991 130992 130993 130994 130995
Compression Stgs.
Part No.
15 24
131782 131783
41 49 57 66 74 83 91 100
131785 131786 131787 131788 131789 131790 131791 131792
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.21 0.2 0.21
10 0.77 0.5 0.5
0.18 0.06 0.06 0.06
ABRASION RESISTANT PUMP Floater Stgs. 8 16 25 33 41 50 58 67 75 84 92 100 108 116 125
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 132941 7 132961 132942 15 132962 132943 24 132963 132944 32 132964 132945 41 132965 132946 49 132966 132947 57 132967 132948 66 132968 132949 74 132969 132950 83 132970 132951 91 132971 132952 100 132972 132953 132954 132955
AR PUMP Part No.
930941 934232 934182 120556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-31
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-2200 1 stage, S.G. = 1
Head M Ft
85 Hz
20
RECOMMENDED OPERATING RANGE
60
80 Hz 75 Hz
16 50
70 Hz 12
65 Hz
40
60 Hz 30
55 Hz
8 50 Hz 45 Hz
20
4 10
0 BPD M3/DAY
0
500 100
1000
1500 200
2000 300
2500 400
3000 500
3500
4000 600
4500 700
5000
CAPACITY
Wood Group ESP, Inc. Page-32
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-300 1 stage @ 3500 RPM, S.G. = 1 Head Pump O.D.* 4” / 101.6 mm M Ft
Qmin
BEP
RECOMMENDED OPERATING RANGE
8
0.5
50%
20
0.4
40%
15
0.3
30%
10
0.2
20%
5
0.1
10%
25
6
HP PMP MTR ONLY LOAD EFF
Qmax
Head
Efficiency
4
2
Power
0 BPD 0 M3/DAY
50 10
100
150 20
200 30
250 40
300
350
50
400 60
450 70
500
550
80
90
0.0 650
600
0%
100
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-150 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1/2 IN 12.69MM 60 HZ 94HP 150HP 192HP
50 HZ 78HP 125HP 160HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TD-300 1 stage @ 2917 RPM, S.G. = 1 Head Pump O.D.* 4” / 102 mm Ft M
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 5
0.3
100%
4
0.2
80%
3
0.2
60%
2
0.1
40%
0.1
20%
0.0
0%
15
10
Efficiency
5
1 Power
0 M3/DAY BPD
0
10 50
20 100
30 150
200
40 250
50 300
60 350
70 400
80
450
500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-150 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1/2 IN 12.69MM 60 HZ 94HP 150HP 192HP
50 HZ 78HP 125HP 160HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-300 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.9 171.5
Stgs. 15 32 49 66 83 100 117 133 150 167 184 201
Part No. 130881 130882 130883 130884 130885 130886 130887 130888 130889 130890 130891 130892
Compression Stgs. 14 31 48 65 82 98
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.23 0.19 0.19
10 0.77 0.72 0.72
0.18 0.07 0.07 0.07
ABRASION RESISTANT PUMP
Part No. 130901 130902 130903 130904 130905 130906
Floater Stgs. 15 31 47 63 78 93 109 125 140 156 171 187
STANDARD PUMP Part No.
4.5 0.35 0.33 0.33
Compression
Part No. Stgs. Part No. 130921 13 130941 130922 29 130942 130923 45 130943 130924 61 130944 130925 76 130945 130926 91 130946 130927 130928 130929 130930 130931 130932
AR PUMP Part No.
930941 934281 926477 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-300 1 stage, S.G. = 1
Head M Ft 14
12
85 Hz RECOMMENDED OPERATING RANGE
45
80 Hz
40
75 Hz
35
70 Hz
10 30 8
6
65 Hz 60 Hz
25
55 Hz
20
50 Hz 15
45 Hz
4 10 2 5
0 BPD M3/DAY
0
100
200 25
300 50
400
500 75
600
700 100
800 125
CAPACITY
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-3000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 30
3.0
90%
25
2.5
75%
20
2.0
60%
1.5
45%
1.0
30%
0.5
15%
Head 8
6
15
Efficiency
4
10
2 5 Power
0 BPD 0 M3/DAY
500
1000
100
1500 200
2000
2500
300
3000
400
3500
500
4000 600
4500
0.0 5000
0%
700
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-3000 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-33
Wood Group ESP, Inc. Pump Performance Curve for TD-3000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head RECOMMENDED OPERATING RANGE 5
1.3
75%
4
1.0
60%
3
0.8
45%
2
0.5
30%
0.3
15%
15
Efficiency 10
5 Power
1
0 M3/DAY BPD
0
100 500
200 1000
300 1500
400
2000
2500
500 3000
0.0 700
600 3500
0%
4000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-3000 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-34
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-3000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378 408 438 468
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5 185.1 198.7 212.3
Stgs. 6 14 21 29 36 44 51 59 66 74 81 89 96 104 111
Part No. 936260 936278 936286 936294 936302 936310 936328 936336 936344 936351 936369 936377 936385 936393 936401
Compression Stgs. 6 14 21 29 36 44 51 59 66 74 81 89 96
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.21 0.2 0.21
10 0.77 0.5 0.5
0.18 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 130241 130242 130243 130244 130245 130246 130247 130248 130249 130250 130251 130252 130253
Floater Stgs. 6 14 21 29 36 44 51 59 66 74 81 89 96 104 111
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 110671 6 130261 110672 14 130262 110673 21 130263 110674 29 130264 110675 36 130265 110676 44 130266 110677 51 130267 110678 59 130268 110679 66 130269 110680 74 130270 110681 81 130271 110682 89 130272 110683 96 130273 110684 100 130274 110685
AR PUMP Part No.
930941 934026 934026 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-35
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-3000 1 stage, S.G. = 1
Head M Ft
85 Hz
16
RECOMMENDED OPERATING RANGE
50 80 Hz 75 Hz 12
40 70 Hz 65 Hz 30
60 Hz
8 55 Hz 50 Hz
20
45 Hz 4 10
0 BPD M3/DAY
0
1000
2000
3000 500
250
4000
5000
6000
750
CAPACITY
Wood Group ESP, Inc. Page-36
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-4300 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 35
3.5
70%
30
3.0
60%
2.5
50%
2.0
40%
15
1.5
30%
10
1.0
20%
0.5
10%
10
8
Head 25
6
20
Efficiency
4
2
Power
5
0 BPD 0 M3/DAY
500 100
1000
1500
200
2000 300
2500 400
3000
3500
500
4000
600
4500 700
5000 800
5500 900
6000
6500
1000
0.0 7000
0%
1100
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-4300 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-37
Wood Group ESP, Inc. Pump Performance Curve for TD-4300 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 101.6 mm
Qmin
Head
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
5
2.5
75%
4
2.0
60%
3
1.5
45%
2
1.0
30%
1
0.5
15%
15
10
Efficiency
5
Power
0 M3/DAY BPD
0
100 500
200 1000
1500
300
400
2000
2500
500 3000
600 3500
700 4000
4500
800 5000
0.0 1000
900 5500
0%
6000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-4300 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-38
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-4300 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378 408 438 468
Bolt on Head (2 7/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5 185.1 198.7 212.3
Stgs. 4 6 13 18 22 27 31 36 40 45 49 54 59 63 68
Part No. 130391 130392 130393 130394 130395 130396 130397 130398 130399 130400 130401 130402 130403 130404 130405
Compression Stgs. 4 8 13 17 22 26 31 35 40 45 49 54 58 63 68
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.21 0.2 0.21
10 0.77 0.5 0.5
0.18 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 130741 130742 130743 130744 130745 130746 130747 130748 130749 130750 130751 130752 130753 130754 130755
Floater Stgs. 4 8 13 17 22 27 31 36 40 45 49 54 59 63 68
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 132541 4 132561 132542 8 132562 132543 13 132563 132544 17 132564 132545 22 132565 132546 26 132566 132547 31 132567 132548 35 132568 132549 40 132569 132550 45 132570 132551 49 132571 132552 54 132572 132553 58 132573 63 132554 132574 68 132555 132575
AR PUMP Part No.
132160 934026 934026 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-39
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-4300 1 stage, S.G. = 1
Head M Ft
16
RECOMMENDED OPERATING RANGE
85 Hz
50
80 Hz
12
75 Hz
40
70 Hz 65 Hz 30 60 Hz
8
55 Hz 20
50 Hz 45 Hz
4 10
0 BPD M3/DAY
0
1000
2000 250
3000 500
4000
5000 750
6000
7000 1000
8000 1250
CAPACITY
Wood Group ESP, Inc. Page-40
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-460 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 102 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 0.7
70%
30
0.6
60%
25
0.5
50%
20
0.4
40%
0.3
30%
0.2
20%
0.1
10%
35 Head 10
8
6
Efficiency
15 4 10
2 Power
5
0 BPD 0 M3/DAY
50 10
100
150
20
200 30
250 40
300
350
50
400 60
450 70
500 80
550 90
600
0.0 700
650 100
0%
110
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-460 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. Pump Performance Curve for TD-460 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
40
Pump O.D.* 4” / 102 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 12
0.3
60%
10
0.3
50%
8
0.2
40%
0.2
30%
0.1
20%
0.1
10%
35
30
25 Head
20
6
Efficiency
15 4 10 Power 2 5
0 M3/DAY BPD
0
10 50
20 100
30 150
40
200
250
50 300
60 350
70 400
450
80 500
0.0 100
90 550
0%
600
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-460 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-10
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-460 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.9 171.5
Stgs. 16 34 52 69 87 105 123 140 158 176 194 211
Part No. 160401 160402 160403 160404 160405 160406 160407 160408 160409 160410 160411 160412
Compression Stgs. 15 33 50 68 86 100
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.23 0.19 0.22
10 1.07 0.65 0.65
0.18 0.07 0.06 0.07
ABRASION RESISTANT PUMP
Part No. 160381 160382 160383 160384 160385 160386
Floater Stgs. 15 32 48 65 81 97 113 129 146 162 179 195
STANDARD PUMP Part No.
4.5 0.5 0.3 0.3
Compression
Part No. Stgs. Part No. 160551 14 160571 160552 31 160572 160553 47 160573 160554 64 160574 160555 79 160575 160556 95 160576 160557 160558 160559 160560 160561 160562
AR PUMP Part No.
930941 934281
934291 926477 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-460 1 stage, S.G. = 1
Head M Ft
85 Hz
20 60
RECOMMENDED OPERATING RANGE
80 Hz 75 Hz
16 50
70 Hz 12
65 Hz
40
60 Hz 30
55 Hz
8 50 Hz 20
45 Hz
4 10
0 BPD M3/DAY
0
100
200 25
300 50
400
500 75
600
700 100
800 125
900
CAPACITY
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-6000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head RECOMMENDED OPERATING RANGE
8
6
25
5.0
100%
20
4.0
80%
3.0
60%
10
2.0
40%
5
1.0
20%
15 Efficiency 4
2
Power
0 BPD 0 M3/DAY
1000
2000
3000
250
4000
500
5000 750
6000
7000
1000
8000
0.0 9000
0%
1250
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-6000 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-41
Wood Group ESP, Inc. Pump Performance Curve for TD-6000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 101.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
20
6
1.5
75%
1.3
63%
4
1.0
50%
3
0.8
38%
2
0.5
25%
0.3
13%
Head
5 Efficiency
15
10
Power
5 1
0 M3/DAY BPD
0
250 1000
500 2000
3000
750 4000
5000
0.0 1250
1000 6000
0%
7000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-6000 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-42
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-6000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378 408 438 468
Bolt on Head (2 7/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5 185.1 198.7 212.3
Stgs. 4 8 13 17 22 27 31 36 40 45 49 54 59 63 68
Part No. 131901 131902 131903 131904 131905 131906 131907 131908 131909 131910 131911 131912 131913 131914 131915
Compression Stgs. 4 8 13 17 22 26 31 35 40 45 49 54 58 63 68
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.21 0.2 0.21
10 0.77 0.5 0.5
0.18 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 131921 131922 131923 131924 131925 131926 131927 131928 131929 131930 131931 131932 131933 131934 131935
Floater Stgs. 4 8 13 17 22 27 31 36 40 45 49 54 59 63 68
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 132581 4 132601 132582 8 132602 132583 13 132603 132584 17 132604 132585 22 132605 132586 26 132606 132587 31 132607 132588 35 132608 132589 40 132609 132590 45 132610 132591 49 132611 132592 54 132612 132593 58 132613 63 132594 132614 68 132595 132615
AR PUMP Part No.
132160 934026 934026 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-43
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-6000 1 stage, S.G. = 1
Head M Ft
85 Hz
16
RECOMMENDED OPERATING RANGE
50 80 Hz 75 Hz 12
40 70 Hz 65 Hz 30
60 Hz
8 55 Hz 50 Hz
20
45 Hz 4 10
0 BPD M3/DAY
0
2000
4000
6000 1000
500
8000
10000
12000
1500
CAPACITY
Wood Group ESP, Inc. Page-44
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-650 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 102 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 30
0.6
60%
25
0.5
50%
0.4
40%
15
0.3
30%
10
0.2
20%
0.1
10%
8
6
Efficiency
20
4
2
Power 5
0 BPD 0 M3/DAY
100
200 25
300
400
50
500
600
75
700
100
800
900
125
1000 150
1100
0.0 1200
0%
175
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-650 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. Pump Performance Curve for TD-650 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 102 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head
20
BEP
7
0.9
70%
6
0.8
60%
0.6
50%
4
0.5
40%
3
0.4
30%
2
0.3
20%
1
0.1
10%
0.0
0%
5
Efficiency
15
10
5
Power 0 M3/DAY BPD
0
25 100
50 200
300
75 400
100
500
600
125 700
800
150 900
1000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-650 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-14
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-650 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.9 171.5
Stgs. 18 37 56 76 95 114 133 153 172 191 210 230
Part No. 131141 131142 131143 131144 131145 131146 131147 131148 131149 131150 131151 131152
Compression Stgs. 15 33 50 68 86 100
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.23 0.19 0.22
10 1.07 0.65 0.65
0.18 0.07 0.06 0.07
ABRASION RESISTANT PUMP
Part No. 130111 130112 130113 130114 130115 130116
Floater Stgs. 17 35 52 71 88 105 123 141 158 176 193 211
STANDARD PUMP Part No.
4.5 0.5 0.3 0.3
Compression
Part No. Stgs. Part No. 118081 14 130121 118082 31 130122 118083 47 130123 118084 64 130124 118085 79 130125 118086 91 130126 118087 118088 118089 118090 118091 118092
AR PUMP Part No.
930941 934281 926477 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-15
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-650 1 stage, S.G. = 1
Head M Ft
85 Hz
20 RECOMMENDED OPERATING RANGE
80 Hz
60
75 Hz 16 50 70 Hz
12
65 Hz
40
60 Hz 30
55 Hz
8
50 Hz 45 Hz
20
4 10
0 BPD M3/DAY
0
200
400 50
600 100
800
1000 150
1200
1400 200
CAPACITY
Wood Group ESP, Inc. Page-16
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TD-850 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 4” / 102 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 30
0.6
60%
25
0.5
50%
20
0.4
40%
0.3
30%
0.2
20%
0.1
10%
8
6
Efficiency 15 4 Power
10
2 5
0 BPD 0 M3/DAY
100
200 25
300
400
50
500 75
600
700
100
800 125
900 150
1000
1100
1200
175
1300 200
1400
0.0 1500
0%
225
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-850 60 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-17
Wood Group ESP, Inc. Pump Performance Curve for TD-850 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 4” / 102 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head
20
BEP
7
0.9
70%
6
0.8
60%
5
0.6
50%
0.5
40%
3
0.4
30%
2
0.3
20%
1
0.1
10%
0.0
0%
15 4
10
Efficiency
5
Power 0 M3/DAY BPD
0
25 100
50 200
300
75 400
500
100 600
125 700
800
150 900
175 1000
1100
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TD-850 50 HZ 5-1/2 IN ROTATIONAL DIRECTION 139.7 MM 4 IN SHAFT DIAMETER 101.60MM 5000 PSI 6000 PSI 8000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 5/8 IN 15.88MM 60 HZ 94 HP 150 HP 192 HP
50 HZ 78 HP 125 HP 160 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-18
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TD-850 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.9 171.5
Stgs. 16 34 52 69 87 105 123 140 158 176 194 211
Part No. 123501 123502 123503 123504 123505 123506 123507 123508 123509 123510 123511 123512
Compression Stgs. 15 33 50 68 86 100
Length Feet Meters
Weight Lbs. Kgs.
0.6 0.23 0.19 0.22
10 1.07 0.65 0.65
0.18 0.07 0.06 0.07
ABRASION RESISTANT PUMP
Part No. 130591 130592 130593 130594 130595 130596
Floater Stgs. 15 32 48 65 81 97 113 129 145 162 178 194
STANDARD PUMP Part No.
4.5 0.5 0.3 0.3
Compression
Part No. Stgs. Part No. 123521 14 130601 123522 31 130602 123523 47 130603 123524 64 130604 123525 79 130605 123526 91 130606 123527 123528 123529 123530 123531 123532
AR PUMP Part No.
930941 934281 926477 120555
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-19
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TD-850 1 stage, S.G. = 1
Head M Ft
85 Hz
20
RECOMMENDED OPERATING RANGE
80 Hz
60
75 Hz
16 50
70 Hz
12
65 Hz
40
60 Hz 30
55 Hz
8 50 Hz 20
45 Hz
4 10
0 BPD M3/DAY
0
200
400 50
600 100
800
1000 150
1200
1400 200
1600 250
CAPACITY
Wood Group ESP, Inc. Page-20
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 400 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TG-4000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.125” / 130.2 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
60
6.0
60%
5.0
50%
4.0
40%
30
3.0
30%
20
2.0
20%
1.0
10%
RECOMMENDED OPERATING RANGE
Head
16 50
12
40
Efficiency
8
4 Power
10
0 BPD 0 M3/DAY
500 100
1000
1500
200
2000 300
2500 400
3000
3500
500
4000 600
4500 700
5000
5500
800
900
6000
0.0 6500
0%
1000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TG-4000 60 HZ 6-5/8 IN ROTATIONAL DIRECTION 168.3 MM 5.13 IN SHAFT DIAMETER 130.18MM 5000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 513 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TG-4000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
40
Pump O.D.* 5.125” / 130.2 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
12
3.0
60%
10
2.5
50%
8
2.0
40%
6
1.5
30%
4
1.0
20%
0.5
10%
Head
RECOMMENDED OPERATING RANGE
35
30
25 Efficiency
20
15
10 Power 2 5
0 M3/DAY BPD
0
100 500
200 1000
300 1500
2000
400 2500
500 3000
600 3500
700 4000
0.0 900
800
4500
5000
0%
5500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TG-4000 50 HZ 6-5/8 IN ROTATIONAL DIRECTION 168.3 MM 5.13 IN SHAFT DIAMETER 130.18MM 5000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 513 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TG-4000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6 19 20.4 21.8
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36 5.79 6.22 6.64
Weight Lbs. 77 145 213 272 340 407 467 535 602 662 730 789 857 924 984
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 34.9 65.8 96.6 123.4 154.2 184.6 211.8 242.7 273.1 300.3 331.1 357.9 388.7 419.1 446.3
Stgs. 5 12 18 25 32 39 46 52 59 66 73 79 86 93 100
Part No. 184021 184022 184023 184024 184025 184026 184027 184028 184029 184030 184031 184032 184033 184034 184035
Compression Stgs. 5 11 18 25 32 38 45 52 59 65 73 79 86 92 100
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
12 1.22 0.85 0.5
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 131161 131162 131163 131164 131165 131166 131167 131168 131169 131170 131171 131172 131173 131174 131175
Floater Stgs. 5 12 18 32 39 46 52 59 66 73 79 86 93 100
STANDARD PUMP Part No.
5.4 0.6 0.4 0.2
Compression
Part No. Stgs. Part No. 111461 5 131221 111462 11 131222 111463 18 131223 25 131224 111465 32 131225 111466 38 131226 111467 45 131227 111468 52 131228 111469 59 131229 111470 65 131230 111471 73 131231 111472 79 131232 111473 86 131233 92 111474 131234 111475 100 131235
AR PUMP Part No.
940510 949651 1011709 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 513 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TG-4000 1 stage, S.G. = 1
Head M Ft 35
RECOMMENDED OPERATING RANGE
85 Hz 30
100 80 Hz
25
75 Hz 80 70 Hz
20
65 Hz 60 60 Hz
15
55 Hz 40
50 Hz 45 Hz
10
20 5
0 BPD M3/DAY
0
1000
2000 250
3000 500
4000
5000 750
6000
7000 1000
CAPACITY
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 513 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-11000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
16 50
10.0
75%
8.0
60%
6.0
45%
4.0
30%
2.0
15%
Head
12
40
30
Efficiency
8
20
Power
4 10
0 BPD 0 M3/DAY
2000
4000 500
6000
8000
10000
1000
12000
1500
2000
14000
0.0 16000
0%
2500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-11000 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-11/16 42.86MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-29
Wood Group ESP, Inc. Pump Performance Curve for TE-11000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 40
Head
10
5.0
50%
2.5
25%
0.0
0%
30
Efficiency
20 5
10
Power
0 M3/DAY BPD
0
250 1000
2000
500 3000
750 4000
5000
1000 6000
1250 7000
8000
1500 9000
1750
10000 11000
2000 12000
13000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-11000 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-11/16 42.86MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-30
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-11000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 116 186 245 314 384 453 523 582 652 721 791 850 920 989 1059
Bolt on Head (3 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 52.6 84.4 111.1 142.4 174.2 205.5 237.2 264.0 295.7 327.0 358.8 385.6 417.3 448.6 480.4
Stgs. 3 7 10 14 18 22 26 29 33 37 41 44 48 52 56
Part No. 138171 138172 138173 138174 138175 138176 138177 138178 138179 138180 138181 138182 138183 138184 138185
Compression Stgs. 3 7 10 14 18 22 26 29 33 37 41 44 48 52 56
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.5 1.69 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 138191 138192 138193 138194 138195 138196 138197 138198 138199 138200 138201 138202 138203 138204 138205
Floater Stgs. 3 7 10 14 18 22 26 29 33 37 41 44 48 52 56
STANDARD PUMP Part No.
10.4 0.7 0.8 0.8
Compression
Part No. Stgs. Part No. 138211 3 138231 138212 7 138232 138213 10 138233 138214 14 138234 138215 18 138235 138216 22 138236 138217 26 138237 138218 29 138238 138219 33 138239 138220 37 138240 138221 41 138241 138222 44 138242 138223 48 138243 138224 52 138244 56 138225 138245
AR PUMP Part No.
940510 123247 952572 952572
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-31
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-11000 1 stage, S.G. = 1
Head M Ft 35
30
RECOMMENDED OPERATING RANGE
100
85 Hz 25
80
80 Hz 75 Hz
20 70 Hz
60
65 Hz 15 60 Hz 40
55 Hz 50 Hz 45 Hz
10
20 5
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
CAPACITY
Wood Group ESP, Inc. Page-32
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-1500 1 stage @ 3500 RPM, S.G. = 1 Head Pump O.D.* 5.375” / 136.6 mm Qmin M Ft
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head
20
RECOMMENDED OPERATING RANGE 60
3.0
60%
40
2.0
40%
1.0
20%
15
10 Efficiency
20 5
Power
0 BPD 0
400
800 100
M3/DAY
1200
1600
200
2000 300
0.0 2800
2400
0%
400
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-1500 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TE-1500 1 stage @ 2917 RPM, S.G. = 1 Head Pump O.D.* 5.375” / 136.6 mm Ft M
Qmin
BEP
RECOMMENDED OPERATING RANGE
Head 50
HP PMP MTR ONLY LOAD EFF
Qmax
15
3.0
60%
2.0
40%
1.0
20%
40
10
Efficiency
30
20 5
10 Power
0 M3/DAY BPD
0
50 250
100 500
150 750
200
1000
1250
250 1500
0.0 350
300 1750
0%
2000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-1500 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-1500 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 117 178 245 312 373 440 502 569 635 697 764 825 892 959 1021
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 53.1 80.7 111.1 141.5 169.2 199.6 227.7 258.1 288.0 316.2 346.5 374.2 404.6 435.0 463.1
Stgs. 7 14 22 30 37 45 52 60 68 78 83 90 98 106 113
Part No. 138631 138632 138633 138634 138635 138636 138637 138638 138639 138640 138641 138642 138643 138644 138645
Compression Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
12 1.22 0.85 0.5
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 138461 138462 138463 138464 138465 138466 138467 138468 138469 138470 138471 138472 138473
Floater Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98 106 113
STANDARD PUMP Part No.
5.4 0.6 0.4 0.2
Compression
Part No. Stgs. Part No. 138671 7 138691 138672 14 138692 138673 22 138693 138674 30 138694 138675 37 138695 138676 45 138696 138677 52 138697 138678 60 138698 138679 68 138699 138680 75 138700 138681 83 138701 138682 90 138702 138683 98 138703 138684 138685
AR PUMP Part No.
940510 949388 120557 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-1500 1 stage, S.G. = 1
Head M Ft 45
85 Hz
140
120
75 Hz
35
30
RECOMMENDED OPERATING RANGE
80 Hz
40
70 Hz
100
65 Hz 25
80
60 Hz
20
55 Hz 60 50 Hz
15 45 Hz 40 10
5
20
0 BPD M3/DAY
0
500
1000 100
1500 200
2000 300
2500 400
3000 500
3500
4000 600
CAPACITY
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-2700 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE Head 20 60
3.0
60%
2.0
40%
1.0
20%
15
Efficiency
40
10
20 Power
5
0 BPD 0 M3/DAY
500
1000
100
1500 200
2000 300
2500 400
3000
3500
500
4000 600
0.0 4500
0%
700
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-2700 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TE-2700 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
50
Head 15
3.0
60%
2.0
40%
1.0
20%
40
Efficiency
10 30
20 5
10 Power
0 M3/DAY BPD
0
50 250
100 500
750
150 1000
200 1250
250 1500
300 1750
2000
350 2250
400
450
2500 2750
500 3000
550
3250
3500
0.0 600
0%
3750
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-2700 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-2700 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 117 178 245 312 373 440 502 569 635 697 764 825 892 959 1021
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 53.1 80.7 111.1 141.5 169.2 199.6 227.7 258.1 288.0 316.2 346.5 374.2 404.6 435.0 463.1
Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98 106 113
Part No. 138761 138762 138763 138764 138765 138766 138767 138768 138769 138770 138771 138772 138773 138774 138775
Compression Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 138741 138742 138743 138744 138745 138746 138747 138748 138749 138750 138751 138752 138753
Floater Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98 106 113
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 138821 7 138801 138822 14 138802 138823 22 138803 138824 30 138804 138825 37 138805 138826 45 138806 138827 52 138807 138828 60 138808 138829 68 138809 138830 75 138810 138831 83 138811 138832 90 138812 138833 98 138813 138834 138835
AR PUMP Part No.
940510 949388 120557 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-2700 1 stage, S.G. = 1
Head M Ft
85 Hz
40 RECOMMENDED OPERATING RANGE
80 Hz 120 35
75 Hz
30
100
25
80
70 Hz 65 Hz 60 Hz
20 55 Hz
60
50 Hz
15
45 Hz
40 10
5
20
0 BPD M3/DAY
0
500 100
1000
1500 200
2000 300
2500 400
3000 500
3500
4000 600
4500 700
5000
CAPACITY
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-3300 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE Head
7.0
70%
60
6.0
60%
50
5.0
50%
40
4.0
40%
30
3.0
30%
20
2.0
20%
1.0
10%
70 20
16
12
Efficiency
8
4
Power
10
0 BPD 0 M3/DAY
500 100
1000
1500
200
2000 300
2500
3000
400
3500
500
4000 600
4500 700
5000 800
5500
0.0 6000
0%
900
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-3300 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. Pump Performance Curve for TE-3300 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 50
3.0
60%
10
2.0
40%
5
1.0
20%
15
Efficiency
40
30
20
Power 10
0 M3/DAY BPD
0
100 500
200 1000
300 1500
2000
400 2500
500 3000
600 3500
0.0 800
700 4000
4500
0%
5000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-3300 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 7/8 IN 22.22MM 60 HZ 256 HP 410 HP 522 HP
50 HZ 213 HP 342 HP 435 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-10
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-3300 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 117 178 245 312 373 440 502 569 635 697 764 825 892 959 1021
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 53.1 80.7 111.1 141.5 169.2 199.6 227.7 258.1 288.0 316.2 346.5 374.2 404.6 435.0 463.1
Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98 106 113
Part No. 158481 158482 158483 158484 158485 158486 158487 158488 158489 158490 158491 158492 158493 158494 158495
Compression Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 158061 158062 158063 158064 158065 158066 158067 158068 158069 158070 158071 158072 158073
Floater Stgs. 7 14 22 30 37 45 52 60 68 75 83 90 98 106 113
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 158501 7 158521 158502 14 158522 158503 22 158523 158504 30 158524 158505 37 158525 158506 45 158526 158507 52 158527 158508 60 158528 158509 68 158529 158510 75 158530 158511 83 158531 158512 90 158532 158513 98 158533 158514 158515
AR PUMP Part No.
940510 138028 120577 120557
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-3300 1 stage, S.G. = 1
Head M Ft
85 Hz RECOMMENDED OPERATING RANGE
45 140
80 Hz
40 75 Hz
120 35
70 Hz 30
100 65 Hz
25
80
60 Hz 55 Hz
20 60
50 Hz
15
45 Hz 40
10
5
20
0 BPD M3/DAY
0
1000
2000 250
3000 500
4000
5000 750
6000
7000 1000
CAPACITY
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-4200 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
7.0
70%
60
6.0
60%
50
5.0
50%
40
4.0
40%
30
3.0
30%
20
2.0
20%
1.0
10%
70 20 Head
16
12
Efficiency
8
4
Power 10
0 BPD 0 M3/DAY
500 100
1000
1500
200
2000 300
2500 400
3000
3500
500
4000 600
4500 700
5000
5500
800
900
6000
0.0 6500
0%
1000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-4200 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. Pump Performance Curve for TE-4200 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
50
Head
3.0
60%
10
2.0
40%
5
1.0
20%
15
40 Efficiency
30
20
Power 10
0 M3/DAY BPD
0
100 500
200 1000
300 1500
2000
400 2500
500 3000
600 3500
700 4000
0.0 900
800
4500
5000
0%
5500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-4200 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-14
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-4200 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 115 180 245 311 376 441 507 572 637 703 768 833 899 964 1029
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 52.2 81.6 111.1 141.1 170.6 200.0 230.0 259.5 288.9 318.9 348.4 377.8 407.8 437.3 466.7
Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Part No. 158651 158652 158653 158654 158655 158656 158657 158658 158659 158660 158661 158662 158663 158664 158665
Compression Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 158631 158632 158633 158634 158635 158636 158637 158638 158639 158640 158641 158642 158643 158644 158645
Floater Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 158821 5 158671 158822 11 158672 158823 17 158673 158824 23 158674 158825 29 158675 158826 35 158676 158827 41 158677 158828 47 158678 158829 53 158679 158830 59 158680 158831 65 158681 158832 71 158682 158833 77 158683 83 158834 158684 89 158835 158685
AR PUMP Part No.
940510 138028 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-15
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-4200 1 stage, S.G. = 1
Head M Ft
RECOMMENDED OPERATING RANGE
45 85 Hz
140 40
80 Hz 120 35
75 Hz
30
100
25
80
70 Hz 65 Hz 60 Hz
20
55 Hz
60
50 Hz
15
45 Hz
40 10
5
20
0 BPD M3/DAY
0
1000
2000 250
3000 500
4000
5000 750
6000
7000 1000
CAPACITY
Wood Group ESP, Inc. Page-16
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-5500 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 25
80
8.0
80%
60
6.0
60%
40
4.0
40%
20
2.0
20%
20
Head 15 Efficiency
10
5
Power
0 BPD 0 M3/DAY
1000
2000 250
3000 500
4000
5000
6000
750
7000
1000
8000 1250
0.0 10000
9000
0%
1500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-4200 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-17
Wood Group ESP, Inc. Pump Performance Curve for TE-5500 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
Head
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
40
Efficiency
10
5.0
50%
2.5
25%
0.0
0%
30
20 5
10
Power
0 M3/DAY BPD
0
250 1000
500 2000
3000
750 4000
5000
1000 6000
1250 7000
8000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-4200 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.44MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-18
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-5500 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 115 180 245 311 376 441 507 572 637 703 768 833 899 964 1029
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 52.2 81.6 111.1 141.1 170.6 200.0 230.0 259.5 288.9 318.9 348.4 377.8 407.8 437.3 466.7
Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Part No. 138351 138352 138353 138354 138355 138356 138357 138358 138359 138360 138361 138362 138363 138364 138365
Compression Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 138331 138332 138333 138334 138335 138336 138337 138338 138339 138340 138341 138342 138343 138344 138345
Floater Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 138371 5 138391 138372 11 138392 138373 17 138393 138374 23 138394 138375 29 138395 138376 35 138396 138377 41 138397 138378 47 138398 138379 53 138399 138380 59 138400 138381 65 138401 138382 71 138402 138383 77 138403 83 138384 138404 89 138385 138405
AR PUMP Part No.
940510 949651 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-19
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-5500 1 stage, S.G. = 1
Head M Ft 40 120
RECOMMENDED OPERATING RANGE
85 Hz
35 80 Hz 30
100
25
80
75 Hz 70 Hz 65 Hz
20
60 Hz 60 55 Hz
15
50 Hz 40
45 Hz
10
5
20
0 BPD M3/DAY
0
2000
4000 500
6000 1000
8000
10000 1500
12000
14000 2000
CAPACITY
Wood Group ESP, Inc. Page-20
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-7000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 25
80
8.0
80%
6.0
60%
4.0
40%
2.0
20%
20 Head 60
15 Efficiency 40 10
20
Power
5
0 BPD 0 M3/DAY
1000
2000 250
3000
4000
500
5000
6000
750
7000
1000
8000
9000
1250
10000
1500
11000
0.0 12000
0%
1750
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-7000 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-21
Wood Group ESP, Inc. Pump Performance Curve for TE-7000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 40
10
5.0
50%
2.5
25%
0.0
0%
Efficiency
30
20 5
10 Power
0 M3/DAY BPD
0
250 1000
500 2000
3000
750 4000
1000
5000
6000
1250 7000
1500
8000
9000
10000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-7000 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-22
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-7000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 115 180 245 311 376 441 507 572 637 703 768 833 899 964 1029
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 52.2 81.6 111.1 141.1 170.6 200.0 230.0 259.5 288.9 318.9 348.4 377.8 407.8 437.3 466.7
Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Part No. 138271 138272 138273 138274 138275 138276 138277 138278 138279 138280 138281 138282 138283 138284 138285
Compression Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 138111 138112 138113 138114 138115 138116 138117 138118 138119 138120 138121 138122 138123 138124 138125
Floater Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 138291 5 138311 138292 11 138312 138293 17 138313 138294 23 138314 138295 29 138315 138296 35 138316 138297 41 138317 138298 47 138318 138299 53 138319 138300 59 138320 138301 65 138321 138302 71 138322 138303 77 138323 83 138304 138324 89 138305 138325
AR PUMP Part No.
940510 949651 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-23
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-7000 1 stage, S.G. = 1
Head M Ft 40
RECOMMENDED OPERATING RANGE
85 Hz
120 35
80 Hz 30
100
25
80
75 Hz 70 Hz 65 Hz
20
60 Hz
60
55 Hz 15 50 Hz 40
45 Hz
10
5
20
0 BPD M3/DAY
0
2000
4000 500
6000 1000
8000
10000 1500
12000 2000
14000
16000 2500
CAPACITY
Wood Group ESP, Inc. Page-24
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TE-7200 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.375” / 136.6 mm Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 25
80
8.0
80%
6.0
60%
4.0
40%
2.0
20%
Head
20 60
15 Efficiency 40 10
Power
20 5
0 BPD 0 M3/DAY
1000
2000 250
3000
4000
500
5000
6000
750
7000
1000
8000
9000
1250
10000
1500
11000
0.0 12000
0%
1750
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-7200 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-25
Wood Group ESP, Inc. Pump Performance Curve for TE-7200 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.375” / 136.6 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head
40
RECOMMENDED OPERATING RANGE Efficiency 10
5.0
50%
5
2.5
25%
0.0
0%
30
20
10 Power
0 M3/DAY BPD
0
250 1000
500 2000
3000
750 4000
1000
5000
6000
1250 7000
1500
8000
9000
10000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TE-7200 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-3/8 IN SHAFT DIAMETER 136.55MM 6000 PSI 6000 PSI 6000 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1 IN 25.40MM 60 HZ 375 HP 600 HP 765 HP
50 HZ 313 HP 500 HP 638 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-26
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TE-7200 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.5 4 5.5 7 8.5 10 11.5 13 14.5 16 17.5 19 20.5 22 23.5
Meters 0.76 1.22 1.68 2.13 2.59 3.05 3.51 3.96 4.42 4.88 5.33 5.79 6.25 6.71 7.16
Weight Lbs. 115 180 245 311 376 441 507 572 637 703 768 833 899 964 1029
Bolt on Head (3-1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 52.2 81.6 111.1 141.1 170.6 200.0 230.0 259.5 288.9 318.9 348.4 377.8 407.8 437.3 466.7
Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Part No. 158771 158772 158773 158774 158775 158776 158777 158778 158779 158780 158781 158782 158783 158784 158785
Compression Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.22 0.2 0.21
23 1.22 1.2 1.2
0.24 0.07 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 158721 158722 158723 158724 158725 158726 158727 158728 158729 158730 158731 158732 158733 158734 158735
Floater Stgs. 5 11 17 23 29 35 41 47 53 59 65 71 77 83 89
STANDARD PUMP Part No.
10.4 0.6 0.5 0.5
Compression
Part No. Stgs. Part No. 158791 5 158741 158792 11 158742 158793 17 158743 158794 23 158744 158795 29 158745 158796 35 158746 158797 41 158747 158798 47 158748 158799 53 158749 158800 59 158750 158801 65 158751 158802 71 158752 158803 77 158753 83 158804 158754 89 158805 158755
AR PUMP Part No.
940510 949651 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-27
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TE-7200 1 stage, S.G. = 1
Head M Ft 40
RECOMMENDED OPERATING RANGE
85 Hz 120 35 80 Hz 30
100
25
80
75 Hz 70 Hz 65 Hz
20
60 Hz 60 55 Hz
15
50 Hz 40
45 Hz
10
5
20
0 BPD M3/DAY
0
2000
4000 500
6000 1000
8000
10000 1500
12000 2000
14000
16000 2500
CAPACITY
Wood Group ESP, Inc. Page-28
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 538 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TH-15000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.625” / 142.9 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head
20
RECOMMENDED OPERATING RANGE 18
16 50 14
12
20.0
50%
18.0
45%
40
16.0
40%
35
14.0
35%
30
12.0
30%
25
10.0
25%
20
8.0
20%
15
6.0
15%
4.0
10%
2.0
5%
0.0 25000
0%
45
Efficiency
10
8
6
4 Power
10 2
5 0 BPD 0
M3/DAY
2500
5000
500
7500 1000
10000
12500
1500
15000
2000
17500
2500
20000 3000
22500 3500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TH-15000 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-5/8 IN SHAFT DIAMETER 142.88MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TH-15000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.625” / 142.9 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
50
15
15.0
75%
10.0
50%
5.0
25%
Head
40
Efficiency
10 30
20 5
10 Power
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
2000
10000
12500
2500 15000
0.0 3500
3000 17500
0%
20000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TH-15000 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-5/8 IN SHAFT DIAMETER 142.88MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TH-15000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Feet 2.1 3.5 4.9 6.3 7.7 9.1 10.5 11.9 13.3 14.7 16.1 17.5 18.9 20.3
Meters 0.64 1.07 1.49 1.92 2.35 2.77 3.20 3.63 4.05 4.48 4.91 5.33 5.76 6.19
Weight Lbs. 108 174 241 307 374 440 506 573 639 706 772 839 905 994
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 49.0 78.9 109.3 139.2 169.6 199.5 229.5 259.9 289.8 320.2 350.1 380.5 410.4 450.8
Stgs.
Part No.
Compression Stgs. 2 5 8 11 14 17 20 23 26 29 32 36 39 42
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.5 1.69 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 123251 123252 123253 123254 123255 123256 123257 123258 123259 123260 123261 123262 123263 123264
Floater Stgs.
5 8 11 14 17 20 23 26 29 32 36 39 42
STANDARD PUMP Part No.
10.4 0.7 0.8 0.8
Compression
Part No. Stgs. Part No. 123372 123373 123374 123375 123376 123377 123378 123379 123380 123381 123382 123383 123384
AR PUMP Part No.
123189 949651 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TH-15000 1 stage, S.G. = 1
Head M Ft 45 140
RECOMMENDED OPERATING RANGE
40 85 Hz
120 35
80 Hz 30
100
25
80
75 Hz 70 Hz 65 Hz 60 Hz
20 60
55 Hz
15
50 Hz 45 Hz
40 10
5
20
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000
CAPACITY
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TH-20000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 5.625” / 142.9 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
Head 20 RECOMMENDED OPERATING RANGE 18
16
14
12
50
25.0
100%
45
22.5
90%
40
20.0
80%
35
17.5
70%
30
15.0
60%
12.5
50%
20
10.0
40%
15
7.5
30%
5.0
20%
2.5
10%
10
8
6
Efficiency
25
4 Power
10 2
5 0 BPD 0
M3/DAY
2500 500
5000
7500
1000
10000 1500
12500
15000
2000
17500
2500
20000 3000
22500
25000
3500
4000
27500
0.0 30000
0%
4500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TH-20000 60 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-5/8 IN SHAFT DIAMETER 142.88MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. Pump Performance Curve for TH-20000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 5.625” / 142.9 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
50
15
15.0
75%
10.0
50%
5.0
25%
Head
40
10 30 Efficiency
20 5
10
Power
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
10000
2000 12500
2500 15000
3000 17500
3500 20000
22500
0.0 4000
0%
25000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TH-20000 50 HZ 7 IN ROTATIONAL DIRECTION 177.8 MM 5-5/8 IN SHAFT DIAMETER 142.88MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-10
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TH-20000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Feet 2.1 3.5 4.9 6.3 7.7 9.1 10.5 11.9 13.3 14.7 16.1 17.5 18.9 20.3
Meters 0.64 1.07 1.49 1.92 2.35 2.77 3.20 3.63 4.05 4.48 4.91 5.33 5.76 6.19
Weight Lbs. 108 174 241 307 374 440 506 573 639 706 772 839 905 994
Bolt on Head (3 - 1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 49.0 78.9 109.3 139.2 169.6 199.5 229.5 259.9 289.8 320.2 350.1 380.5 410.4 450.8
Stgs.
Part No.
Compression Stgs. 2 5 8 11 14 17 20 23 26 29 32 36 39 42
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.5 1.69 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 123351 123352 123353 123354 123355 123356 123357 123358 123359 123360 123361 123362 123363 123364
Floater Stgs.
STANDARD PUMP Part No.
10.4 0.7 0.8 0.8
Compression
Part No. Stgs. Part No. 2 123391 5 123392 8 123393 11 123394 14 123395 17 123396 20 123397 23 123398 26 123399 29 123400 32 123401 36 123402 39 123403 42 123404
AR PUMP Part No.
123189 949651 123270 123270
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TH-20000 1 stage, S.G. = 1
Head M Ft 45 140
RECOMMENDED OPERATING RANGE
40 85 Hz
120 35
80 Hz
30
100
25
80
75 Hz 70 Hz 65 Hz 60 Hz
20 60
55 Hz
15
50 Hz 45 Hz
40 10
5
20
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000
35000 5000
CAPACITY
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 562 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TJ-12000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 6.75” / 171.5 mmQmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 30
25
100
25.0
100%
20.0
80%
15.0
60%
10.0
40%
5.0
20%
Head
80
20 60 Efficiency 15 40 10
Power
20 5
0 BPD 0 M3/DAY
2000
4000 500
6000
8000
1000
10000
12000
1500
14000
2000
16000
18000
2500
20000
3000
22000
0.0 24000
0%
3500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-12000 60 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. Pump Performance Curve for TJ-12000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 6.75” / 171.5 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 70 Head 20
20.0
100%
15
15.0
75%
10
10.0
50%
5
5.0
25%
0.0
0%
60
50
Efficiency 40
30
20
10
Power
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
2000
10000
12500
2500 15000
3000 17500
20000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-12000 50 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171..45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-10
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TJ-12000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.7 4 5.4 6.8 8.2 9.5 10.9 12.3 13.7 15 16.4 17.8 19.2 20.5 21.9
Meters 0.82 1.22 1.65 2.07 2.50 2.90 3.32 3.75 4.18 4.57 5.00 5.43 5.85 6.25 6.68
Weight Lbs. 192 286 378 472 566 659 751 845 939 1033 1125 1218 1313 1406 1499
Bolt on Head (3 -1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 87.1 129.7 171.4 214.1 256.7 298.9 340.5 383.2 425.8 468.5 510.2 552.4 595.4 637.6 679.8
Stgs.
Part No.
Compression Stgs. 2 5 8 11 14 17 20 23 26 29 32 35 38 41 44
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.22 1.22 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 117391 117392 117393 117394 117395 117396 117397 117398 117399 117400 117401 117402 117403 117404 117405
Floater Stgs.
STANDARD PUMP Part No.
10.4 0.6 0.6 0.8
Compression
Part No. Stgs. Part No. 2 118061 5 118062 8 118063 11 118064 14 118065 17 118066 20 118067 23 118068 26 118069 29 118070 32 118071 35 118072 38 118073 41 118074 44 118075
AR PUMP Part No.
957647 952572 952572 952572
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TJ-12000 1 stage, S.G. = 1
Head M Ft
85 Hz 60
200 80 Hz RECOMMENDED OPERATING RANGE
75 Hz
50 150
70 Hz
40
65 Hz 60 Hz
30
100 55 Hz 50 Hz
20
45 Hz 50
10
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
CAPACITY
Product Catalog - Pump Curves 338 Series - Copyright Wood Group ESP, Inc. - February, 2009
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TJ-20000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
30
25
Pump O.D.* 6.75” / 171.5 mm
Qmin
BEP
RECOMMENDED OPERATING RANGE
Head
100
HP PMP MTR ONLY LOAD EFF
Qmax
80
50.0
100%
40.0
80%
30.0
60%
20.0
40%
10.0
20%
20 60
Efficiency
15 40 10
20
Power
5
0 BPD 0 M3/DAY
5000
10000 1000
15000
20000
2000
25000
3000
0.0 30000
0%
4000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-20000 60 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. Pump Performance Curve for TJ-20000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 6.75” / 171.5 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 70 20
16.0
80%
15
12.0
60%
8.0
40%
4.0
20%
60
50
Efficiency 40
10 30 Power 20 5 10
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
10000
2000 12500
2500 15000
3000 17500
3500 20000
22500
0.0 4000
0%
25000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-20000 50 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-14
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TJ-20000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.7 4 5.4 6.8 8.2 9.5 10.9 12.3 13.7 15 16.4 17.8 19.2 20.5 21.9
Meters 0.82 1.22 1.65 2.07 2.50 2.90 3.32 3.75 4.18 4.57 5.00 5.43 5.85 6.25 6.68
Weight Lbs. 182 263 343 424 504 568 648 729 809 890 970 1050 1131 1194 1275
Bolt on Head (3 -1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 82.6 119.3 155.6 192.3 228.6 257.6 293.9 330.7 367.0 403.7 440.0 476.3 513.0 541.6 578.3
Stgs.
Part No.
Compression Stgs. 2 5 8 11 14 16 19 22 25 28 31 34 37 39 42
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.22 1.22 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 147471 147472 147473 147474 147475 147476 147477 147478 147479 147480 147481 147482 147483 147484 147485
Floater Stgs.
STANDARD PUMP Part No.
10.4 0.6 0.6 0.8
Compression
Part No. Stgs. Part No. 2 147531 5 147532 8 147533 11 147534 14 147535 16 147536 19 147537 22 147538 25 147539 28 147540 31 147541 34 147542 37 147543 39 147544 42 147545
AR PUMP Part No.
957647 952572 952572 952572
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-15
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TJ-20000 1 stage, S.G. = 1
Head M Ft
60
200
85 Hz RECOMMENDED OPERATING RANGE
80 Hz 50
75 Hz 150 70 Hz
40 65 Hz
30
60 Hz
100
55 Hz 50 Hz 20
45 Hz 50
10
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000 5000
35000
40000 6000
CAPACITY
Wood Group ESP, Inc. Page-16
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TJ-7500 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
24
Pump O.D.* 6.75” / 171.5 mmQmin RECOMMENDED OPERATING RANGE
Head
80
HP PMP MTR ONLY LOAD EFF
BEP Qmax
20.0
80%
17.5
70%
15.0
60%
50
12.5
50%
40
10.0
40%
30
7.5
30%
20
5.0
20%
2.5
10%
70 20 60
Efficiency
16
12
8
4
Power 10
0 BPD 0 M3/DAY
2000
4000 500
6000
8000
10000
1000
12000
1500
2000
14000
0.0 16000
0%
2500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-7500 60 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TJ-7500 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 6.75” / 171.5 mm
Qmin
HP PMP MTR ONLY LOAD EFF
BEP Qmax
RECOMMENDED OPERATING RANGE Head
50
7.5
75%
10
5.0
50%
5
2.5
25%
0.0
0%
15
40 Efficiency
30
20
Power
10
0 M3/DAY BPD
0
250 1000
2000
500 3000
750 4000
5000
1000 6000
1250 7000
8000
1500 9000
1750
10000 11000
2000 12000
13000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-7500 50 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TJ-7500 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.7 4 5.4 6.8 8.2 9.5 10.9 12.3 13.7 15 16.4 17.8 19.2 20.5 21.9
Meters 0.82 1.22 1.65 2.07 2.50 2.90 3.32 3.75 4.18 4.57 5.00 5.43 5.85 6.25 6.68
Weight Lbs. 210 327 419 511 603 714 806 898 1009 1104 1193 1304 1396 1488 1580
Bolt on Head (3 -1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 95.2 148.3 190.0 231.7 273.5 323.8 365.5 407.2 457.6 500.7 541.0 591.4 633.1 674.8 716.5
Stgs.
Part No.
Compression Stgs. 2 6 9 12 15 19 22 25 29 32 35 39 42 45 48
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.22 1.22 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 117271 117272 117273 117274 117275 117276 117277 117278 117279 117280 117281 117282 117283 117284 117285
Floater Stgs.
STANDARD PUMP Part No.
10.4 0.6 0.6 0.8
Compression
Part No. Stgs. Part No. 2 117841 6 117842 9 117843 12 117844 15 117845 19 117846 22 117847 25 117848 29 117849 32 117850 35 117851 39 117852 42 117853 45 117854 48 117855
AR PUMP Part No.
957647 952572 952572 952572
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TJ-7500 1 stage, S.G. = 1
Head M Ft 50
RECOMMENDED OPERATING RANGE
85 Hz
160
45
80 Hz
140 40
75 Hz 120
35
70 Hz
30
100
25
80
65 Hz 60 Hz 55 Hz
20 60
50 Hz
15
45 Hz 40
10 5
20
0 BPD M3/DAY
0
2000
4000 500
6000 1000
8000
10000 1500
12000 2000
14000
16000 2500
18000
CAPACITY
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TJ-9000 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 6.75” / 171.5 mmQmin
BEP
RECOMMENDED OPERATING RANGE
Head
30
25
HP PMP MTR ONLY LOAD EFF
Qmax
100
20.0
100%
80
16.0
80%
12.0
60%
8.0
40%
4.0
20%
20 Efficiency
60
15 40 10 Power 20 5
0 BPD 0 M3/DAY
2000
4000 500
6000
8000
10000
1000
12000
1500
2000
14000
0.0 16000
0%
2500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-9000 60 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TJ-9000 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 6.75” / 171.5 mm
Qmin
BEP
Head
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
70 20
20.0
100%
15
15.0
75%
10
10.0
50%
5
5.0
25%
60
50
40
Efficiency
30
20
10 Power
0 M3/DAY BPD
0
250 1000
2000
500 3000
750 4000
5000
1000 6000
1250 7000
8000
1500 9000
0.0 2000
1750 10000
11000
0%
12000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TJ-9000 50 HZ 8-5/8 IN ROTATIONAL DIRECTION 219.1 MM 6-3/4 IN SHAFT DIAMETER 171.45MM 3000 PSI 3600 PSI 3600 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-3/16 IN 30.16MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TJ-9000 HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Feet 2.7 4 5.4 6.8 8.2 9.5 10.9 12.3 13.7 15 16.4 17.8 19.2 20.5 21.9
Meters 0.82 1.22 1.65 2.07 2.50 2.90 3.32 3.75 4.18 4.57 5.00 5.43 5.85 6.25 6.68
Weight Lbs. 210 328 421 513 606 718 810 903 1015 1110 1200 1312 1404 1497 1590
Bolt on Head (3 -1/2"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 95.3 148.8 191.0 232.7 274.9 325.7 367.4 409.6 460.4 503.5 544.3 595.1 636.9 679.0 721.2
Stgs.
Part No.
Compression Stgs. 2 6 9 12 15 19 22 25 29 32 35 39 42 45 48
Length Feet Meters
Weight Lbs. Kgs.
0.8 0.23 0.2 0.26
23 1.22 1.22 1.69
0.24 0.07 0.06 0.08
ABRASION RESISTANT PUMP
Part No. 117901 117902 117903 117904 117905 117906 117907 117908 117909 117910 117911 117912 117913 117914 117915
Floater Stgs.
STANDARD PUMP Part No.
10.4 0.6 0.6 0.8
Compression
Part No. Stgs. Part No. 2 147291 6 147292 9 147293 12 147294 15 147295 19 147296 22 147297 25 147298 29 147299 32 147300 35 147301 39 147302 42 147303 45 147304 48 147305
AR PUMP Part No.
957647 952572 952572 952572
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TJ-9000 1 stage, S.G. = 1
Head M Ft 50
75 Hz RECOMMENDED OPERATING RANGE
160
70 Hz
45 140
65 Hz
40 120
60 Hz
35 30
100
25
80
55 Hz 50 Hz 45 Hz
20 60 15 40 10 5
20
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
CAPACITY
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. Pump Performance Curve for TM-19000A 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 8.62” / 219 mm
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 150
60.0 Head
40
30
125
50.0
100
40.0
100%
30.0
75%
20.0
50%
10.0
25%
75
Efficiency
20
50
10 Power
25
0 BPD 0 M3/DAY
4000
8000
12000
1000
16000
2000
20000 3000
24000
28000
4000
32000
0.0 36000
0%
5000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000A 60 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. Pump Performance Curve for TM-19000A 1 stage @ 2917 RPM, S.G. = 1 Head M Ft
RECOMMENDED Qmin BEP OPERATING RANGE
Pump O.D.* 8.62” / 219 mm
HP PMP MTR ONLY LOAD EFF
Qmax
Head 100
30
30.0
75%
25
25.0
63%
20
20.0
50%
15
15.0
38%
10
10.0
25%
5.0
13%
90
80
Efficiency
70
60
50
40
30
Power
20 5 10
0 M3/DAY BPD
0
500 2500
1000 5000
1500
7500
2000
10000
12500
2500 15000
3000 17500
20000
3500 22500
4000 25000
0.0 5000
4500 27500
0%
30000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000A 50 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TM-19000A HOUSING DATA STANDARD PUMP Length Hsg Feet Meters 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Weight Lbs.
Floater
Kgs.
Stgs.
ABRASION RESISTANT PUMP
Compression
Part No. Stgs.
Floater
Part No. Stgs.
Compression
Part No. Stgs.
Part No.
Exclude
Length Weight Feet Meters Lbs. Kgs. Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
0.8 0.23 0.2 0.26
0.24 0.07 0.06 0.08
23 1.22 1.22 1.69
STANDARD PUMP Part No.
AR PUMP Part No.
10.4 0.6 0.6 0.8
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TM-19000A 1 stage, S.G. = 1
Head M Ft 90
85 Hz RECOMMENDED OPERATING RANGE
80 80 Hz
250 70
60
75 Hz 200
70 Hz 65 Hz
50 150
60 Hz
40
30
55 Hz 50 Hz
100
45 Hz 20 50 10
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000 5000
35000
40000 6000
CAPACITY
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 675 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-4
Wood Group ESP, Inc. Pump Performance Curve for TM-19000B 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 8.62” / 219 mm
Qmin
30
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
40 Head
125
BEP
50.0
100
40.0
100%
75
30.0
75%
20.0
50%
10.0
25%
20
Efficiency
50
10 25
Power
0 BPD 0 M3/DAY
2000
4000
500
6000
8000
1000
0.0 10000 12000 14000 16000 18000 20000 22000 24000 26000 28000 30000 1500
2000
2500
3000
3500
4000
0%
4500
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000B 60 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. Pump Performance Curve for TM-19000B 1 stage @ 2917 RPM, S.G. = 1 Head M Ft
Pump O.D.* 8.62” / 219 mm
Qmin
90
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 80
BEP
25
25.0
20
20.0
100%
15
15.0
75%
10.0
50%
5.0
25%
70
60
50
Efficiency 40 10 30
20 Power
5 10
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
10000
2000 12500
2500 15000
3000 17500
3500 20000
22500
0.0 4000
0%
25000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000B 50 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-4
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TM-19000B HOUSING DATA STANDARD PUMP Length Hsg Feet Meters 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Weight Lbs.
Floater
Kgs.
Stgs.
ABRASION RESISTANT PUMP
Compression
Part No. Stgs.
Floater
Part No. Stgs.
Compression
Part No. Stgs.
Part No.
Exclude
Length Weight Feet Meters Lbs. Kgs. Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
0.8 0.23 0.2 0.26
0.24 0.07 0.06 0.08
23 1.22 1.22 1.69
STANDARD PUMP Part No.
AR PUMP Part No.
10.4 0.6 0.6 0.8
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TM-19000B 1 stage, S.G. = 1
Head M Ft
85 Hz
70
RECOMMENDED OPERATING RANGE
80 Hz 60
200 75 Hz
50
70 Hz 150
65 Hz
40 60 Hz
30
55 Hz
100
50 Hz 45 Hz 20 50 10
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000 5000
35000
CAPACITY
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-6
Wood Group ESP, Inc. Pump Performance Curve for TM-19000C 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
Pump O.D.* 8.62” / 219 mm
Qmin
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
Head 30
BEP
100
40.0
100%
75
30.0
75%
20.0
50%
10.0
25%
20
50 Efficiency
10 25 Power
0 BPD 0 M3/DAY
2000
4000 500
6000
8000
1000
10000 1500
12000
14000
2000
16000 2500
18000
20000
3000
22000 3500
24000
0.0 26000
0%
4000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000C 60 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. Pump Performance Curve for TM-19000C 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
Pump O.D.* 8.62” / 219 mm
Qmin
BEP
Head
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
70 20
20.0
100%
15
15.0
75%
10.0
50%
5.0
25%
60
50
40
Efficiency 10
30
20 5
Power
10
0 M3/DAY BPD
0
500 2500
1000 5000
1500 7500
2000
10000
12500
2500 15000
0.0 3500
3000 17500
0%
20000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TM-19000C 50 HZ 10-3/4 IN ROTATIONAL DIRECTION 273.1 MM 8-5/8 IN SHAFT DIAMETER 219.08MM 2000 PSI 2400 PSI 2400 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/5 IN 30.48MM 60 HZ 637 HP 1019 HP 1300 HP
50 HZ 531 HP 849 HP 1083 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-6
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
TM-19000C HOUSING DATA STANDARD PUMP Length Hsg Feet Meters 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Weight Lbs.
Floater
Kgs.
Stgs.
ABRASION RESISTANT PUMP
Compression
Part No. Stgs.
Floater
Part No. Stgs.
Compression
Part No. Stgs.
Part No.
Exclude
Length Weight Feet Meters Lbs. Kgs. Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
0.8 0.23 0.2 0.26
0.24 0.07 0.06 0.08
23 1.22 1.22 1.69
STANDARD PUMP Part No.
AR PUMP Part No.
10.4 0.6 0.6 0.8
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TM-19000C 1 stage, S.G. = 1
Head M Ft
60
200
85 Hz RECOMMENDED OPERATING RANGE
80 Hz 50
75 Hz 150 70 Hz
40 65 Hz
30
60 Hz
100
55 Hz 50 Hz 20
45 Hz 50
10
0 BPD M3/DAY
0
5000
10000 1000
15000 2000
20000 3000
25000 4000
30000 5000
35000
CAPACITY
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-8
Wood Group ESP, Inc. Pump Performance Curve for TN-35000A 1 stage @ 3500 RPM, S.G. = 1 Head M Ft
70
#VALUE!
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE
225.0 90%
225 Head
60
200
200.0 80%
175
175.0 70%
150
150.0 60%
125
125.0 50%
100
100.0 40%
50
40
30
75
50 10 25
0 BPD 0 M3/DAY
75.0
30%
50.0
20%
25.0
10%
Efficiency
20
Power
5000 1000
0.0 10000 15000 20000 25000 30000 35000 40000 45000 50000 55000 60000 65000 70000 75000 2000
3000
4000
5000
6000
7000
8000
9000
10000
0%
11000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TN-35000A 60 HZ 11-3/4 IN ROTATIONAL DIRECTION 298.5 MM 9-1/2 IN SHAFT DIAMETER 241.29MM 2300 PSI 2760 PSI 2760 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/2 IN 38.09MM 60 HZ 1000 HP 1600 HP 2040 HP
50 HZ 833 HP 1333 HP 1700 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Pages
www.woodgroup-esp.com Page-1
Page 1
Wood Group ESP, Inc. Pump Performance Curve for TN-35000A 1 stage @ 2917 RPM, S.G. = 1 Head Ft M
#VALUE!
Qmin
BEP
HP PMP MTR ONLY LOAD EFF
Qmax
RECOMMENDED OPERATING RANGE 45
112.5 Head
100
40
100.0 100%
35
87.5
88%
30
75.0
75%
25
62.5
63%
20
50.0
50%
37.5
38%
25.0
25%
12.5
13%
0.0
0%
90 80 70 60 50
Efficiency
15
40 30
10 Power
20 5 10 0 M3/DAY BPD
0
1000 5000
2000 10000
15000
3000
4000
20000
25000
5000 30000
6000 35000
7000 40000
45000
8000 50000
9000 55000
CAPACITY These curves represent nominal performance to be used in pump sizing calculations. Actual pump performance will comply with acceptance limits specified in Table 4.1, API representative 11 S2 (Recommended Practice for Submersible Pump Testing -- August 1, 1997)
MINIMUM CASING SIZE HOUSING DIAMETER* HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE ULTRA HIGH PRESSURE
ENGINEERING DATA TN-35000A 50 HZ 11-3/4 IN ROTATIONAL DIRECTION 298.5 MM 9-1/2 IN SHAFT DIAMETER 241.29MM 2300 PSI 2760 PSI 2760 PSI
SHAFT POWER LIMIT STANDARD HIGH STRENGTH ULTRA HIGH STRENGTH
CCW 1-1/2 IN 38.09MM 60 HZ 1000 HP 1600 HP 2040 HP
50 HZ 833 HP 1333 HP 1700 HP
*Diameter does not include lockplates
Wood Group ESP, Inc.
The ESP Specialists
Page-2
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Pages
www.woodgroup-esp.com
Page 2
Wood Group ESP, Inc.
TN-35000A HOUSING DATA STANDARD PUMP Length Hsg 1 2 3 4 5 6 7 8 9 10 11 12
Feet 2.1 3.5 4.9 6.3 7.8 9.2 10.6 12 13.4 14.8 16.2 17.6
Meters 0.64 1.07 1.49 1.92 2.38 2.80 3.23 3.66 4.08 4.51 4.94 5.36
Weight Lbs. 44 74 105 135 166 196 226 257 287 318 348 378
Bolt on Head (2 3/8"-8rd) Coupling for Intake or GS Pump to Pump Coupling - FLT Pump to Pump Coupling - CMP
Floater
Kgs. 20.0 33.6 47.6 61.2 75.3 88.9 102.5 116.6 130.2 144.2 157.8 171.5
Stgs. 14 30 47 63 79 95 111 128 144 160 176 192
Part No. 192421 192422 192423 192424 192425 192426 192427 192428 192429 192430 192431 192432
Compression Stgs. 13 29 45 62 78 94
Length Feet Meters
Weight Lbs. Kgs.
0.3 0.21 0.2 0.21
10 0.77 0.5 0.5
0.09 0.06 0.06 0.06
ABRASION RESISTANT PUMP
Part No. 192381 192382 192383 192384 192385 192386
Floater Stgs. 13 29 43 58 73 87 102 117 131 146 161 175
STANDARD PUMP Part No.
4.5 0.3 0.2 0.2
Compression
Part No. Stgs. Part No. 192391 12 192411 192392 27 192412 192393 41 192413 192394 56 192414 192395 71 192415 192396 87 192416 192397 192398 192399 192400 192401 192402
AR PUMP Part No.
930941 934232 934182 120556
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Pages
www.woodgroup-esp.com Page-3
Page 3
Wood Group ESP, Inc. Variable Frequency Pump Performance Curve for TN-35000A 1 stage, S.G. = 1
Head M Ft
85 Hz
RECOMMENDED OPERATING RANGE
400 80 Hz 350
75 Hz
100 90
300
70 Hz 65 Hz
80 250 70 60
60 Hz 200
55 Hz
50
50 Hz
150
45 Hz
40 30
100
20 50 10 0 BPD M3/DAY
0
10000 1000 2000
20000 3000
4000
30000 5000
40000 6000 7000
50000 8000
60000 9000 10000
70000 11000
CAPACITY
Wood Group ESP, Inc.
The ESP Specialists
Page-4
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Pages
www.woodgroup-esp.com
Page 4
Wood Group ESP, Inc.
ENGINEERING DATA TM19000A 60 HZ HOUSING DIAMETER
8.62 IN.
MINIMUM CASING SIZE
10-3/4 IN.
SHAFT DIAMETER
1-3/16 IN.
MINIMUM SHAFT AREA
1.1075 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
637 HP 1019 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
33 STAGES 52 STAGES 54 STAGES 31 STAGES 38 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc.
ENGINEERING DATA TM19000A 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
47 STAGES 75 STAGES 70 STAGES 45 STAGES 54 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** - For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TM19000B 60 HZ HOUSING DIAMETER
8.62 IN.
MINIMUM CASING SIZE
10-3/4 IN.
SHAFT DIAMETER
1-3/16 IN.
MINIMUM SHAFT AREA
1.1075 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
637 HP 1019 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
44 STAGES 71 STAGES 64 STAGES 38 STAGES 45 STAGES
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
ENGINEERING DATA TM19000B 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
64 STAGES 102 STAGES 84 STAGES 54 STAGES 65 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TM19000C 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
73 STAGES 117 STAGES 103 STAGES 67 STAGES 80 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
TM-19000 PUMP 862 Series - Compression Hsg 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Length Feet Meters 3.3 1.01 3.9 1.19 4.5 1.37 5.1 1.55 5.7 1.74 6.3 1.92 6.9 2.10 7.5 2.29 8.1 2.47 8.7 2.65 9.3 2.83 9.9 3.02 10.6 3.23 11.2 3.41 11.8 3.60 12.4 3.78 13.0 3.96 13.6 4.15 14.2 4.33 14.8 4.51 15.4 4.69 16.0 4.88 16.6 5.06 17.2 5.24 17.8 5.43 18.4 5.61 19.0 5.79 19.6 5.97 20.2 6.16 20.8 6.34
Weight Lbs. Kgs. 528 239.4 587 266.2 662 300.2 729 330.6 789 357.8 863 391.4 931 422.2 991 449.4 1058 479.8 1126 510.6 1193 541.0 1260 571.4 1327 601.8 1395 632.6 1466 664.8 1533 695.2 1596 723.8 1664 754.6 1734 786.4 1801 816.8 1866 846.2 1933 876.6 2003 908.4 2071 939.2 2138 969.6 2202 998.6 2272 1030.4 2339 1060.7 2407 1091.6 2474 1122.0
No. Stages 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Length Meters 0.30
A-Cut Part Number 117653 117654 117655 117656 117657 117658 117659 117660 117661 117662 117663 117664 117665 117666 117667 117668 117669 117670 117671 117672 117673 117674 117675 117676 117677 117678 117679 117680 117681 117682
B-Cut Part Number 117311 117312 117313 117314 117315 117316 117317 117318 117319 117320 117321 117322 117323 117371 117372 117373 117374 117200 117375 117376 117377 117378 117379 117380 117381 117382 117383 117384 117385 117386
Weight Lbs. Kgs. 62 28.1
C-Cut Part Number 117683 117684 117685 117686 117687 117688 117689 117690 117691 117692 117693 117694 117695 117696 117697 117698 117699 117700 117701 117702 117703 117704 117705 117706 117707 117708 117709 117710 117711 117712
STANDARD PUMP Part No. 117786
Bolt on Head (7”-8rd)-LT
Feet 0.97
Coupling for Intake or GS
0.22
0.06
1.22
0.55
952572
Pump to Pump Coupling
0.22
0.06
1.22
0.55
952572
Shim Kit
0.08
0.02
0.06
0.03
131613
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-10
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TM24000A 60 HZ HOUSING DIAMETER
8.62 IN.
MINIMUM CASING SIZE
10-3/4 IN.
SHAFT DIAMETER
1-3/16 IN.
MINIMUM SHAFT AREA
1.1075 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
637 HP 1019 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
20 STAGES 32 STAGES 55 STAGES 29 STAGES 35 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc.
ENGINEERING DATA TM24000A 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
29 STAGES 46 STAGES 71 STAGES 42 STAGES 51 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TM24000B 60 HZ HOUSING DIAMETER
8.62 IN.
MINIMUM CASING SIZE
10-3/4 IN.
SHAFT DIAMETER
1-3/16 IN.
MINIMUM SHAFT AREA
1.1075 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
637 HP 1019 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
23 STAGES 36 STAGES 65 STAGES 37 STAGES 44 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc.
ENGINEERING DATA TM24000B 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
32 STAGES 52 STAGES 84 STAGES 53 STAGES 64 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-14
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TM24000C 60 HZ HOUSING DIAMETER
8.62 IN.
MINIMUM CASING SIZE
10-3/4 IN.
SHAFT DIAMETER
1-3/16 IN.
MINIMUM SHAFT AREA
1.1075 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
637 HP 1019 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
31 STAGES 49 STAGES 81 STAGES 46 STAGES 55 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-15
Wood Group ESP, Inc.
ENGINEERING DATA TM24000C 50 HZ HOUSING DIAMETER
218.95 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
273.05 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER
30.175 MM
MINIMUM SHAFT AREA
715.14 MM 2 P
SHAFT LIMIT STANDARD HIGH STRENGTH
531 HP 849 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2000 PSI 2400 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
45 STAGES 71 STAGES 105 STAGES 67 STAGES 80 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** - For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-16
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
TM-24000 PUMP 862 Series - Compression Hsg 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Length Feet Meters 3.3 1.01 3.9 1.19 4.5 1.37 5.1 1.55 5.7 1.74 6.3 1.92 6.9 2.10 7.5 2.29 8.1 2.47 8.7 2.65 9.3 2.83 9.9 3.02 10.6 3.23 11.2 3.41 11.8 3.60 12.4 3.78 13.0 3.96 13.6 4.15 14.2 4.33 14.8 4.51 15.4 4.69 16.0 4.88 16.6 5.06 17.2 5.24 17.8 5.43 18.4 5.61 19.0 5.79 19.6 5.97 20.2 6.16 20.8 6.34
Weight Lbs. Kgs. 528 239.4 587 266.2 662 300.2 729 330.6 789 357.8 863 391.4 931 422.2 991 449.4 1058 479.8 1126 510.6 1193 541.0 1260 571.4 1327 601.8 1395 632.6 1466 664.8 1533 695.2 1596 723.8 1664 754.6 1734 786.4 1801 816.8 1866 846.2 1933 876.6 2003 908.4 2071 939.2 2138 969.6 2202 998.6 2272 1030.4 2339 1060.7 2407 1091.6 2474 1122.0
No. Stages 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Length Meters 0.30
A-Cut Part Number 117473 117474 117475 117476 117477 117478 117479 117480 117481 117482 117483 117484 117485 117486 117487 117488 117427 117428 117491 117492 117493 117494 117495 117496 117497 117498 117499 117500 117501 117502
B-Cut Part Number 117503 117504 117505 117506 117507 117508 117509 117510 117511 117512 117513 117514 117515 117516 117517 117518 117519 117520 117521 117522 117523 117524 117525 117526 117527 117528 117529 117530 117531 117532
Weight Lbs. Kgs. 62 28.1
C-Cut Part Number 117533 117534 117535 117536 117537 117538 117539 117540 117541 117542 117543 117544 117545 117546 117547 117548 117549 117550 117551 117552 117553 117554 117555 117556 117557 117558 117559 117560 117561 117562
STANDARD PUMP Part No. 117786
Bolt on Head (7”-8rd)
Feet 0.97
Coupling for Intake or GS
0.22
0.06
1.22
0.55
952572
Pump to Pump Coupling
0.22
0.06
1.22
0.55
952572
Shim Kit
0.08
0.02
0.06
0.03
131613
Pumps are center tandem configuration that can be stacked to achieve desired number of stages up to horsepower limits of shafting. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-17
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-18
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-19
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-20
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 862 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000A 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
17 STAGES 27 STAGES 19 STAGES 25 STAGES 30 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc.
ENGINEERING DATA TN35000A 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
24 STAGES 39 STAGES 25 STAGES 36 STAGES 43 STAGES
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000B 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
23 STAGES 36 STAGES 23 STAGES 30 STAGES 36 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
ENGINEERING DATA TN35000B 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
33 STAGES 52 STAGES 30 STAGES 43 STAGES 51 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000C 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
29 STAGES 47 STAGES 28 STAGES 35 STAGES 43 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc.
ENGINEERING DATA TN35000C 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
42 STAGES 67 STAGES 36 STAGES 51 STAGES 61 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
TN-35000 UT PUMP 950 Series - Compression Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Length Feet Meters 2.4 0.73 3.0 0.91 3.6 1.10 4.2 1.28 4.7 1.43 5.3 1.62 5.9 1.80 6.5 1.98 7.1 2.16 7.6 2.32 8.2 2.50 8.8 2.68 9.4 2.87 10.0 3.05 10.6 3.23 11.1 3.38 11.7 3.57 12.3 3.75 12.9 3.93 13.5 4.11
Weight Lbs. Kgs. 516 234.0 592 268.5 668 302.9 744 337.4 817 370.5 892 404.5 968 439.0 1044 473.5 1120 507.9 1193 541.0 1269 575.5 1345 610.0 1421 644.4 1497 678.9 1573 713.4 1649 747.6 1725 762.3 1801 816.8 1877 851.2 1953 885.7
No. Stages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Coupling for Intake or GS
Feet 0.22
Pump to Pump Coupling
0.22
A-Cut Part Number 1033018 1033026 1033034 1033042 1033059 1033067 1033075 1033083 1033091 1033109 1033117 1033125 1033133 1033141 1033158
Length Meters 0.06 0.06
B-Cut Part Number 1033216 1033224 1033232 1033240 1033257 1033265 1033273 1033281 1033299 1033307 1033315 1033323 1033331 1033349 1033356 1033364 1033372 1033380 1033398 1033406
Weight Lbs. Kgs. 1.22 0.55 1.22
0.55
C-Cut Part Number 1033414 1033422 1033430 1033448 1033455 1033463 1033471 1033489 1033497 1033505 1033513 1033521 1033539 1033547 1033554 1033562 1033570 1033588 1033596 1033604
STANDARD PUMP Part No. 1032770 1032770
Shim Kit 0.08 0.02 0.02 0.01 131613 Pumps are upper tandem configuration. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-10
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000A 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
17 STAGES 27 STAGES 19 STAGES 25 STAGES 30 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc.
ENGINEERING DATA TN35000A 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
24 STAGES 39 STAGES 25 STAGES 36 STAGES 43 STAGES
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000B 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
23 STAGES 36 STAGES 23 STAGES 30 STAGES 36 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
ENGINEERING DATA TN35000B 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
33 STAGES 52 STAGES 30 STAGES 43 STAGES 51 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
ENGINEERING DATA TN35000C 60 HZ HOUSING DIAMETER MINIMUM CASING SIZE SHAFT DIAMETER MINIMUM SHAFT AREA
9.50 IN. 11-3/4 IN. 1-1/2 IN. 1.7671 IN.
SHAFT LIMIT STANDARD HIGH STRENGTH
1000 HP 1600 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
ROTATIONAL DIRECTION
CCW
MAXIMUM STAGING * SHAFT
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
29 STAGES 47 STAGES 28 STAGES 35 STAGES 43 STAGES
18000 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc.
ENGINEERING DATA TN35000C 50 HZ HOUSING DIAMETER
241.30 MM
ROTATIONAL DIRECTION
MINIMUM CASING SIZE
298.45 MM
MAXIMUM STAGING:* SHAFT
SHAFT DIAMETER MINIMUM SHAFT AREA
38.1 MM 1140.09 MM2
SHAFT LIMIT STANDARD HIGH STRENGTH
833 HP 1333 HP
HOUSING PRESSURE LIMIT STANDARD HIGH PRESSURE
2300 PSI 2760 PSI
CCW
STANDARD HIGH STRENGTH THRUST BEARING - COMPRESSION PUMP HIGH LOAD (250ºF BHT MAX)** HOUSING STANDARD HIGH PRESSURE
THRUST BEARING CAPACITY HIGH LOAD (250ºF BHT MAX)
42 STAGES 67 STAGES 36 STAGES 51 STAGES 61 STAGES
16300 LBS.
* - Maximum staging may be limited by housing pressure limit, shaft capacity or thrust loading, reference Engineering Section or contact your local Wood Group ESP representative. ** For applications above 250ºF, contact your Wood Group ESP representative.
Wood Group ESP, Inc. Page-6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
TN-35000 UT PUMP 950 Series - Compression Hsg 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Length Feet Meters 2.4 0.73 3.0 0.91 3.6 1.10 4.2 1.28 4.7 1.43 5.3 1.62 5.9 1.80 6.5 1.98 7.1 2.16 7.6 2.32 8.2 2.50 8.8 2.68 9.4 2.87 10.0 3.05 10.6 3.23 11.1 3.38 11.7 3.57 12.3 3.75 12.9 3.93 13.5 4.11
Weight Lbs. Kgs. 516 234.0 592 268.5 668 302.9 744 337.4 817 370.5 892 404.5 968 439.0 1044 473.5 1120 507.9 1193 541.0 1269 575.5 1345 610.0 1421 644.4 1497 678.9 1573 713.4 1649 747.6 1725 762.3 1801 816.8 1877 851.2 1953 885.7
No. Stages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Coupling for Intake or GS
Feet 0.22
Pump to Pump Coupling
0.22
A-Cut Part Number 1033018 1033026 1033034 1033042 1033059 1033067 1033075 1033083 1033091 1033109 1033117 1033125 1033133 1033141 1033158
Length Meters 0.06 0.06
B-Cut Part Number 1033216 1033224 1033232 1033240 1033257 1033265 1033273 1033281 1033299 1033307 1033315 1033323 1033331 1033349 1033356 1033364 1033372 1033380 1033398 1033406
Weight Lbs. Kgs. 1.22 0.55 1.22
0.55
C-Cut Part Number 1033414 1033422 1033430 1033448 1033455 1033463 1033471 1033489 1033497 1033505 1033513 1033521 1033539 1033547 1033554 1033562 1033570 1033588 1033596 1033604
STANDARD PUMP Part No. 1032770 1032770
Shim Kit 0.08 0.02 0.02 0.01 131613 Pumps are upper tandem configuration. Part numbers shown are for pumps constructed with steel housings. For design requirements not listed consult your Wood Group ESP representative. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page-10
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Pump Curves 950 Series - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
BOLT ON INTAKES DESCRIPTION PUMP SERIES 338 INTAKE, PUMP BO TA STL INTAKE, PUMP BO TA SST INTAKE, PUMP BO TA AR STL INTAKE, PUMP BO TA AR SST INTAKE, PUMP BO TA AR STL HSS PUMP SERIES 387 INTAKE, PUMP BO TR387 STL INTAKE, PUMP BO TR387 SST INTAKE, PUMP BO TR387 AR STL INTAKE, PUMP BO TR387 AR SST PUMP SERIES 400 INTAKE, PUMP BO TD STL INTAKE, PUMP BO TD SST INTAKE, PUMP BO TD AR STL INTAKE, PUMP BO TD AR SST INTAKE, PUMP BO TD AR STL HSS INTAKE, PUMP BO TD AR SST HSS INTAKE, PUMP BO TD AR NITRIDE INTAKE, PUMP BO TD AR FPS INTAKE, PUMP BO TD AR DURAGUARD INTAKE, PUMP BO TD AR BDP STL INTAKE, PUMP BO TD AR 316SST HSS INTAKE, PUMP BO TD AR STL UHSS INTAKE, PUMP BO TD AR 316SST UHSS PUMP SERIES 513 / 538 INTAKE, PUMP BO TE/TG STL INTAKE, PUMP BO TE/TG STL HSS INTAKE, PUMP BO TE/TG SST INTAKE, PUMP BO TE/TG AR STL INTAKE, PUMP BO TE/TG AR SST PUMP SERIES 562 INTAKE, PUMP BO TH STL INTAKE, PUMP BO TH SST INTAKE, PUMP BO TH AR STL HSS INTAKE, PUMP BO TH AR STL INTAKE, PUMP BO TH AR SST HSS INTAKE, PUMP BO TH AR SST
Wood Group ESP, Inc.
HP Rating 60Hz 50Hz
Length Ft. M.
Weight Lbs. Kgs.
PART NO.
125 125 125 125 200
104 104 104 104 167
0.77 0.77 0.77 0.77 0.77
0.23 0.23 0.23 0.23 0.23
18 18 18 18 18
8.16 8.16 8.16 8.16 8.16
1021443 113143 113429 113430 113722
256 256 256 256
213 213 213 213
1 1 1 1
0.3 0.3 0.3 0.3
28 28 28 28
12.7 12.7 12.7 12.7
116080 116081 150732 150733
256 256 256 256 410 410 256 256 256 256 410 522 522
213 213 213 213 342 342 213 213 213 213 342 435 435
1 1 1 1 1 1 1 1 1 1 1 1 1
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
28 28 28 28 28 28 28 28 28 28 28 28 28
12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7
935858 1006071 140796 140800 140801 140802 150212 150593 150640 170427 170814 190063 190149
637 1019 637 1019 1019
531 849 531 849 849
1.24 1.24 1.24 1.24 1.24
0.38 0.38 0.38 0.38 0.38
45 45 45 45 45
20.41 20.41 20.41 20.41 20.41
138028 141221 138029 138032 138033
637 637 1019 637 1019 637
531 531 849 531 849 531
1.24 1.24 1.24 1.24 1.24 1.24
0.38 0.38 0.38 0.38 0.38 0.38
50 50 50 50 50 50
22.68 22.68 22.68 22.68 22.68 22.68
123206 123410 136098 123585 153245 173022
The ESP Specialists
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 1
Wood Group ESP, Inc.
BOLT ON INTAKES HP Rating 60Hz 50Hz
DESCRIPTION PUMP SERIES 675 INTAKE, PUMP BO TJ STL INTAKE, PUMP BO TJ SST INTAKE, PUMP BO TJ STL HSS INTAKE, PUMP BO TJ AR STL INTAKE, PUMP BO TJ AR SST INTAKE, PUMP BO TJ AR SST HSS INTAKE, PUMP BO TJ AR SST UHSS PUMP SERIES 862 INTAKE, PUMP BO TM STL INTAKE, PUMP BO TM SST INTAKE, PUMP BO TM AR SHORT STL PUMP SERIES 950 INTAKE, PUMP BO TN/TR7 SEAL STL INTAKE, PUMP BO TN/TR7 SEAL SST INTAKE, PUMP BO TN STL INTAKE, PUMP BO TN SST
Wood Group ESP, Inc. Page - 2
Length Ft. M.
Weight Lbs. Kgs.
PART NO.
637 637 1019 637 637 1019 1281
531 531 849 531 531 849 1067
0.73 0.73 0.73 0.73 0.73 0.73 0.73
0.22 0.22 0.22 0.22 0.22 0.22 0.22
56 56 56 56 56 56 56
25.4 25.4 25.4 25.4 25.4 25.4 25.4
957498 117409 147744 117791 117819 147070 157077
637 637 637
531 531 531
0.8 0.8 0.8
0.24 0.24 0.24
75 75 75
34 34 34
977710 117961 117787
1000 1000 1000 1000
833 833 833 833
0.83 0.83 0.83 0.83
0.25 0.25 0.25 0.25
85 85 85 85
38.6 38.6 38.6 38.6
1033612 147012 1032705 1033687
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
GAS SEPARATORS Wood Group ESP offers a variety of gas separator models for different well conditions. These models are offered in all three series. It is important to mention here the features of these models. STANDARD (3B-3 Bearing Separators): These separators are intended for use in abrasive / non-abrasive well conditions. Solid tungsten carbide bushing/sleeves are used in these units. Internal compression tubes are coated with a highly abrasive resistant coating. Units are provided with a stainless steel base. STAINLESS STEEL (SST): In a SST construction, SST is used to make the following components. All other components are the same as the standard unit. Head Lock ring / Compression nut Ferretic Housing (9 Chrome 1 Moly) WAG UNITS: WAG units are designed for highly corrosive CO2 environments. These units essentially have SST construction with the following features added SST Housing (410 SST) Lock plates are not used on these units. Housing joints are locked with a thread XGC MODELS: XGC models are designed for applications having excessive gas. Any of the above mentioned models can be offered in XGC separators. XGVS MODELS: The Extra Gas Volume Separator is available in 538 series for high volume applications up to 7,500 BPD liquid rate. XGVS units are constructed in corrosion resistant configuration as standard with three tungsten carbide bearings, stainless steel head and base, stainless steel internal parts, T9 housing, and Monel® K-500 shaft. The high strength shaft (HSS) option upgrades the shaft to Inconel® 718. MAGS MODELS: The Multi-stage Abrasion-resistant Gas Separator (MAGS) of Wood Group ESP features patented designs to achieve high gas separation efficiencies in a wide range of production flow rates. The 400 series MAGS has the maximum capacity of 8,000 BPD liquid production. And the 538 series MAGS can handle liquid flow rate up to 16,000 BPD. As standard features, all MAGS units are equipped with stainless steel head and base, Tungsten Carbide (TC) bushing and sleeve for radial bearings, TC coated stainless steel compression tubes, and Ni-resist steel casting inducers, diffusers, and crossovers. The MAGS is suitable for high temperature environment with key-locked TC bushings to the bearing supports. The 538 series gas separators (XGVS and MAGS) are Left Hand Threads. COATINGS: Any gas separator can be supplied with coated internals. Coatings available are the same as those available for pump stages. Typical coatings are BDP (Boron Diffusion Process) for abrasives and FPS (Fluoropolymer System) for scale. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 3
Wood Group ESP, Inc.
GAS SEPARATORS Length Ft. M.
DESCRIPTION TR3 SERIES GAS SEPERATOR TR3 RS GAS SEPARATOR TR3 UT GAS SEPARATOR TR3 LT STL HSS
2.21 2.25 2.21
0.67 0.69 0.67
Weight Lbs. Kgs. 38 38 38
17.23 17.23 17.23
Part No. 113091 113275 113625
ENGINEERING DATA - TR3 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 3-3/8 IN HOUSING DIAMETER 85.85 MM SHAFT DIAMETER 11/16 IN SHAFT DIAMETER 17.42 MM SHAFT LIMIT STANDARD 125 HP SHAFT LIMIT STANDARD 104 HP HIGH STRENGTH 200 HP HIGH STRENGTH 167 HP Length Ft. M.
DESCRIPTION TR387 SERIES GAS SEPARATOR TR387 3B LT STL GAS SEPARATOR TR387 3B LT SST
3.02 3.02
0.92 0.92
Weight Lbs. Kgs.
Part No.
68.00 68.00
141925 113566
30.84 30.84
ENGINEERING DATA - TR387 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 3.87 IN HOUSING DIAMETER 98.30 MM SHAFT DIAMETER 7/8 IN SHAFT DIAMETER 22.2 MM SHAFT LIMIT STANDARD 256 HP SHAFT LIMIT STANDARD 213 HP HIGH STRENGTH 410 HP HIGH STRENGTH 342 HP
Wood Group ESP, Inc. Page - 4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
GAS SEPARATORS Length Ft. M.
DESCRIPTION
Weight Lbs. Kgs.
PART NO.
TR4 SERIES GAS SEPARATOR TR4 3B LT STL GAS SEPARATOR TR4 3B LT SST GAS SEPARATOR TR4 3B LT HSS GAS SEPARATOR TR4 3B LT BDP GAS SEPARATOR TR4 3B LT FPS GAS SEPARATOR TR4 3B LT SST HSS GAS SEPARATOR TR4 3B LT SST WAG GAS SEPARATOR TR4 3B LT SST UHSS WAG GAS SEPARATOR TR4 3B LT SST SR GAS SEPARATOR TR4 3B UT STL GAS SEPARATOR TR4 3B UT SST GAS SEPARATOR TR4 UT STL HSS GAS SEPARATOR TR4 UT SST HSS
3.02 3.02 3.02 3.02 3.02 3.02 3.02 3.02 3.02 3.06 3.06 3.06 3.06
0.92 0.92 0.92 0.92 0.92 0.92 0.92 0.92 0.92 0.93 0.93 0.93 0.93
72 72 72 72 72 72 71 71 73 70 70 70 70
32.65 32.65 32.65 32.65 32.65 32.65 32.2 32.2 33.11 31.75 31.75 31.75 31.75
160118 150624 160122 160400 160126 160128 141464 150465 150425 160130 160132 160134 160136
GAS SEPARATOR TR4 AR MAGS-3 SST T9 HSS GAS SEPARATOR TR4 AR MAGS-3 SST HSS GAS SEPARATOR TR4 AR MAGS-3 SST T9 UHSS
6.23 6.23 6.23
1.90 1.90 1.90
143 143 143
65 65 65
192455 192469 192708
ENGINEERING DATA - TR4 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 4.00 IN HOUSING DIAMETER 101.60 MM SHAFT DIAMETER 7/8 IN SHAFT DIAMETER 22.2 MM SHAFT LIMIT STANDARD 256 HP SHAFT LIMIT STANDARD 213 HP HIGH STRENGTH 342 HP HIGH STRENGTH 410 HP ULTRA HIGH STRENGTH 435 HP ULTRA HIGH STRENGTH 522 HP
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. – October, 2009
www.woodgroup-esp.com Page - 5
Wood Group ESP, Inc.
GAS SEPARATORS Length
DESCRIPTION TR5 SERIES GAS SEPARATOR TR5 3B LT STL GAS SEPARATOR TR5 3B LT SST GAS SEPARATOR TR5 3B LT STL HSS GAS SEPARATOR TR5 3B LT SST HSS GAS SEPARATOR TR5 3B LT STL BDP GAS SEPARATOR TR5 3B LT SST FPS GAS SEPARATOR TR5 3B LT SST WAG GAS SEPARATOR TR5 3B UT STL GAS SEPARATOR TR5 3B UT SST GAS SEPARATOR TR5 3B UT STL HSS GAS SEPARATOR TR5 3B UT SST HSS
Ft.
M.
3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2
0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98
Weight Lbs. Kgs. 132 132 132 132 132 132 131 140 140 140 140
59.86 59.86 59.86 59.86 59.86 59.86 59.41 63.49 63.49 63.49 63.49
PART NO. 141463 141254 151089 151458 151345 151092 151104 151106 151108 151110 151112
ENGINEERING DATA - TR5 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 5-1/8” IN HOUSING DIAMETER 130.30 MM SHAFT DIAMETER 1-3/16 IN SHAFT DIAMETER 30.20 MM SHAFT LIMIT STANDARD 637 HP SHAFT LIMIT STANDARD 531 HP HIGH STRENGTH 1019 HP HIGH STRENGTH 849 HP
Wood Group ESP, Inc. Page - 6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. – October, 2009
Wood Group ESP, Inc.
GAS SEPARATORS Length Ft. M.
DESCRIPTION
Weight Lbs. Kgs.
PART NO.
TR538 SERIES GAS SEPARATOR TR538 XGVS LT SST T9 GAS SEPARATOR TR538 XGVS LT SST T9 HSS GAS SEPARATOR TR538 XGVS UT SST T9 GAS SEPARATOR TR538 XGVS UT SST T9 HSS
3.59 3.59 3.25 3.25
1.09 1.09 0.99 0.99
140 140 135 135
63.49 63.49 61.22 61.22
158136 158102 158139 158122
GAS SEPARATOR TR538 AR MAGS-3 SST T9 HSS GAS SEPARATOR TR538 AR MAGS-3 SST HSS GAS SEPARATOR TR538 AR MAGS-3 SST
7.70 7.70 7.70
2.35 2.35 2.35
256 256 256
116 116 116
161308 161309 161325
ENGINEERING DATA - TR538 50 HZ OPERATION 60 HZ OPERATION 136.50 MM HOUSING DIAMETER 5-3/8” IN HOUSING DIAMETER 30.20 MM SHAFT DIAMETER 1-3/16 IN SHAFT DIAMETER STANDARD 531 HP SHAFT LIMIT STANDARD 637 HP SHAFT LIMIT HIGH STRENGTH 849 HP HIGH STRENGTH 1019 HP TR675 SERIES Lower Tandem / Single for attachment to TR5 Seal GAS SEPARATOR TR675-TR5 LT GAS SEPARATOR TR675-TR5 LT SST GAS SEPARATOR TR675-TR5 LT HSS GAS SEPARATOR TR675-TR5 LT SST HSS lower Tandem / Single for attachment to TR7 Seal GAS SEPARATOR TR675 LT GAS SEPARATOR TR675 LT SST GAS SEPARATOR TR675 LT HSS GAS SEPARATOR TR675 LT SST HSS Upper Tandem GAS SEPARATOR TR675 UT GAS SEPARATOR TR675 UT SST GAS SEPARATOR TR675 UT HSS GAS SEPARATOR TR675 UT SST HSS
3.48 3.48 3.48 3.48
1.06 1.06 1.06 1.06
190 190 190 190
86.17 86.17 86.17 86.17
118213 118167 118215 118217
3.48 3.48 3.48 3.48
1.06 1.06 1.06 1.06
190 190 190 190
86.17 86.17 86.17 86.17
118195 118211 118197 118199
3.48 3.48 3.48 3.48
1.06 1.06 1.06 1.06
190 190 190 190
86.17 86.17 86.17 86.17
118201 118203 118205 118207
ENGINEERING DATA - TR675 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 6.750 IN HOUSING DIAMETER 171.45 MM SHAFT DIAMETER 1.187 IN SHAFT DIAMETER 30.20 MM SHAFT LIMIT STANDARD 637 HP SHAFT LIMIT STANDARD 531 HP HIGH STRENGTH 1019 HP HIGH STRENGTH 849 HP Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Intakes / Gas Separators - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 7
Wood Group ESP, Inc. 300 SERIES STANDARD MOTORS 3.75" / 95.25 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 7.5 6.2 410 342 10.5 8.7 390 342 315 262 15 12.5 400 333 387 322 19.5 16.2 630 525 330 275 22.5 18.7 440 367 730 608 370 308 25.5 21.2 500 417 630 525
AMPS 14 20.5 35.5 28 38 23 51.5 38.5 23 51 37 30
4-1/2" / 114.3 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT LT Ft M Lbs Kgs 113102G 6.4 1.95 208 94.4 113103G 8.3 2.53 270 122 113104G 113113G 113122G 11.1 3.38 361 164 113105G 113114G 113123G 113106G 113107G 113130G 113108G 113109G 113110G 113131G 113111G
113115G 113116G 113132G 113117G 113118G 113119G 113133G 113120G
113124G 113125G
13.9
4.24
456
207
15.8
4.82
514
233
17.7
5.39
660
299
300 SERIES THD MOTORS 3.75" / 95.25 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 10 8.3 455 380 15 12.5 455 370 25 20.8 490 405 455 380 30 25 745 620 520 430 35 29.2 865 730 595 495 40 33.3 750 625
AMPS 17 26 39 50 30 51 30 49 40
DESCRIPTION
NUMBERS UT 113287G 113288G 113292G 113295G 113298G 113304G 113307G 113313G 113316G
CT
113293G 113296G 113299G 113305G 113308G 113314G 113317G
PART NUMBERS
HEAD , MTR TR3-92 BOLT-ON KIT, BASE MTR TR3 Y-PT STL KIT, INSTALLATION TR3
Wood Group ESP, Inc.
4-1/2" / 114.3 MM O.D. or Larger Casing LENGTH WEIGHT LT Ft M Lbs Kgs 6.4 1.95 208 94.4 8.3 2.53 270 122 11.1 3.38 361 164
113268 1048610 1054444
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
13.9
4.24
456
207
15.8
4.82
514
233
17.7
5.39
660
299
LENGTH Ft M 1.1 0.34 0.5 0.15 NA NA
WEIGHT Lbs Kgs 28 12.7 15 6.8 0.5 0.23
www.woodgroup-esp.com Page - 1
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page - 2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 400 SERIES STANDARD MOTORS 4.56" / 115.82 MM O.D. VOLTS HP AMPS 60 Hz 50 Hz 60 Hz 50 Hz 435 362 10 8.7 15 15 12.5 435 362 23 610 508 16 450 375 28.5 20 16.5 750 625 17 410 342 39 25 20.8 690 575 22 810 675 20 425 354 44.5 30 25 750 625 25.5 400 333 55 35 29.2 675 562 33 750 625 28 420 350 62 770 642 33 40 33.3 880 733 29 1295 1079 20 675 562 47 815 679 39 50 41.7 955 796 33 1070 892 31 1210 1008 27 640 533 59 810 675 47 60 50 970 808 39 1330 1108 29 1945 1621 20
DESCRIPTION
5-1/2" / 139.70 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT PLUG-IN Ft M Lbs Kgs 4.1 1.25 240 109 110752G 130296G 110753G 130297G 5.3 1.62 288 131 110699G 130298G 110754G 130299G 6.5 1.98 345 156 110755G 130300G 110756G 130320G 7.7 2.35 402 183 110757G 130615G 110700G 120387G 110758G 130616G 8.9 2.71 462 210 110759G 120388G 110760G 130617G 110761G 130618G 10.1 3.08 520 236 110762G 192355G 130619G 110763G 130620G 110764G 130621G 11.3 3.44 577 262 110765G 192352G 130622G 110766G 130623G 110767G 130624G 110768G 130625G 110769G 130626G 13.7 4.18 694 315 110770G 130627G 110771G 120389G 110772G 110809G 130628G 110773G 110810G 130629G 110774G 110811G 130630G 16.5 5.03 810 367 110775G 110812G 120861G 110776G 130631G
PART NUMBERS
HEAD , MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT, INSTALLATION TR4
Wood Group ESP, Inc.
110669 1008109 1054451
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.5 21 9.53 0.21 0.1
www.woodgroup-esp.com Page - 3
Wood Group ESP, Inc. 400 SERIES STANDARD MOTORS continued 4.56" / 115.82 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 540 450 82.5 750 625 60 70 58.3 945 787 47 1135 946 39 1310 1092 35 635 529 80 860 717 60 80 66.7 1085 904 46 1310 1092 39 2155 1796 24 710 592 81 960 800 59 1135 946 50 90 75 46 1220 1017 39 1460 1217 31 1930 1608 646 84 775 59 1075 896 100 83.3 46 1355 1129 2205 1837 28.5 1190 992 60 110 91.7 2380 1983 30 930 775 84 1040 867 76 120 100 1125 937 70 1295 1079 59 2245 1871 35
DESCRIPTION
5-1/2" / 139.70 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT PLUG-IN Ft M Lbs Kgs 110777G 110813G 130632G 110778G 110814G 130633G 110779G 110815G 130634G 18.4 5.61 885 402 110780G 110816G 120390G 110781G 110817G 130635G 110782G 110818G 130636G 110783G 110819G 130637G 110784G 110820G 130638G 20.8 6.34 994 451 110785G 110821G 130639G 110786G 130640G 110787G 110822G 130641G 110788G 110823G 130642G 110789G 110824G 130643G 110826G 130644G 23.2 7.07 1115 506 110792G 110825G 130239G 110790G 130240G 110791G 110827G 130257G 110793G 110828G 130258G 110794G 25.6 7.8 1295 588 110829G 120447G 110795G 130259G 110796G 110830G 130260G 110797G 28 8.53 1395 632 130275G 110798G 110831G 130276G 110799G 110832G 130277G 110800G 110833G 130278G 30.4 9.27 1500 681 110801G 110834G 130279G 110802G 130280G 110803G
PART NUMBERS
HEAD , MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT, INSTALLATION TR4
110669 1008109 1054451
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.5 21 9.53 0.21 0.1
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 4
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 400 SERIES THD MOTORS 4.56" / 115.82 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 15 12.5 505 421 20 16.5 675 562 30 25 870 725 780 650 35 29.2 915 762 495 412 37.5 45 870 725 770 642 41.7 50 885 737 1020 850 50 60 1505 1254 1245 1037 62.5 75 1410 1175 1540 1283 74.7 90 2260 1883 1320 1100 87.5 105 1520 1267 1520 1267 100 120 2505 2087 1700 1417 112.5 135 2240 1867 1575 1312 125 150 2560 2133 1380 1150 137.5 165 2770 2308 1505 1254 150 180 2610 2175
DESCRIPTION Head, MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT INSTALLATION TR4
Wood Group ESP, Inc.
AMPS 20 20 23 28 25 59 34 42 36 39 27 41 36 39 27 52 47 52 32 52 41 61 38 80 40 79 47
5-1/2" / 139.70 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT Ft M Lbs Kgs 120255G 4.1 1.25 240 108.9 120257G 5.3 1.62 288 131 120259G 6.5 1.98 345 155 120261G 7.7 2.35 402 183 120262G 120263G 210 8.9 2.71 462 120264G 120265G 236 10.1 3.08 520 120266G 120269G 262 11.3 3.44 577 120270G 120274G 315 13.7 4.18 694 120275G 120279G 120311G 368 16.5 5.03 810 120280G 120284G 120315G 402 18.4 5.61 885 120285G 120316G 120289G 120320G 451 20.8 6.34 994 120290G 120295G 120325G 23.2 7.07 1115 506 120296G 120299G 120328G 25.6 7.8 1295 588 120300G 120301G 120329G 28 8.53 1395 633 120302G 120306G 120333G 30.4 9.27 1500 681 120307G
PART NUMBERS 110669 1008109 1054451
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.52 21 9.53 0.21 0.1
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Page - 5
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 6
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 500 SERIES STANDARD MOTORS 5.44" / 138.20 MM O.D. (PLUG-IN: 5.56" / 141.22MM O.D) HP VOLTS NUMBERS AMPS CT 60 Hz 50 Hz 60 Hz 50 Hz UT 440 367 29 111807G 20 16.7 755 629 17 111808G 1020 850 12 111809G 435 362 45 111810G 30 25 710 592 28 111811G 1215 1012 16 111812G 435 362 60 111813G 730 608 36 111814G 40 33.3 880 733 30 111815G 1325 1104 20 111816G 450 375 72 111817G 725 604 45 111818G 50 41.7 905 754 35 111819G 1270 1058 25 111820G 1375 1146 22 111821G 425 354 91 111822G 645 537 59 111823G 870 725 45 111824G 60 50 970 808 40 111825G 1085 904 35 111826G 1320 1100 30 111827G 755 629 60 111829G 70 58.3 1015 846 45 111830G 1215 1054 35 111831G 865 721 60 111832G 80 66.7 1160 967 45 111833G 2180 1817 23 111834G
DESCRIPTION
131217G
PART NUMBERS
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
Wood Group ESP, Inc.
6-5/8" / 168.28 MM O.D. or Larger LENGTH WEIGHT PLUG-IN Ft M Lbs Kgs
111906 1017318 1054469
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
5
1.52
300
137
6.3
1.92
390
177
7.7
2.35
483
219
9.1
2.77
575
261
10.5
3.2
678
308
11.8
3.6
770
349
13.2 4.02
862
391
LENGTH Ft M 1.3 0.42 0.75 0.23 NA NA
WEIGHT Lbs Kgs 81 36.7 26 11.8 1.3 0.6
www.woodgroup-esp.com Page - 7
Wood Group ESP, Inc. 500 SERIES STANDARD MOTORS continued 5.40" / 137.16 MM O.D. (PLUG-IN: 5.56" / 141.22MM O.D) 6-5/8" / 168.28 MM O.D. or Larger VOLTS HP PART NUMBERS LENGTH WEIGHT AMPS UT CT PLUG-IN 60 Hz 50 Hz 60 Hz 50 Hz Ft M Lbs Kgs 111835G 705 587 90 111836G 111988G 835 696 76 111837G 111989G 100 83.3 15.9 4.85 1047 471 1070 892 60 111838G 111990G 131218G 1255 1046 50 111839G 131385G 2170 1808 29 111840G 111991G 855 712 88 111841G 111992G 1030 858 73 120 100 18.7 5.7 1232 554 111842G 111993G 131219G 1295 1079 59 111843G 2165 1804 33 111844G 111994G 925 771 88 130 108.3 19.9 6.07 1287 585 111845G 111957G 1125 937 73 111846G 111958G 985 821 90 140 116.7 1210 1008 111847G 111959G 21.4 6.52 1417 644 67 111848G 131096G 2015 1679 44 111849G 111995G 1075 896 87 150 125 111850G 111996G 131097G 22.8 6.95 1514 688 1240 1033 76 111851G 2105 1754 44 111852G 111961G 825 687 122 111853G 111962G 1115 929 88.5 160 133.3 24.2 7.38 1620 736 111854G 2003 1699 50 111855G 2185 1821 46 111856G 111963G 945 787 120 111857G 111964G 131220G 1275 1062 89 180 150 26.9 8.2 1833 833 111858G 131098G 1945 1621 59 111859G 2260 1883 50 111860G 111997G 1100 917 115 200 166.7 29.6 9.02 2018 917 111861G 131099G 2140 1783 54 111862G 111998G 1135 946 127 225 187.5 29.6 9.02 2018 917 111863G 131310G 2235 1862 64
DESCRIPTION
PART NUMBERS
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
111906 1017318 1054469
LENGTH Ft M 1.3 0.42 0.75 0.23 NA NA
WEIGHT Lbs Kgs 81 36.7 26 11.8 1.3 0.6
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 8
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 500 SERIES THD MOTORS 5.40" / 137.16 MM O.D. HP VOLTS NUMBERS AMPS UT 60 Hz 50 Hz 60 Hz 50 Hz 121155G 510 425 37 25 30 1190 992 15 121157G 510 425 58 121158G 37.5 45 1420 1183 21 121160G 1025 854 39 121163G 50 60 1545 1287 26 121164G 1055 879 45 121167G 62.5 75 1600 1333 28 121169G 1130 942 52 121173G 75 90 1540 1283 39 121176G 1180 983 58 121178G 105 87.5 1475 1229 45 121179G 1350 1125 58 121181G 100 120 2540 2117 30 121182G 1460 1217 65 121186G 125 150 2350 1958 37 121187G 1200 1000 94 121189G 150 180 2525 2104 43 121191G 87 121193G 195 162.5 1310 1092 1150 958 116 121194G 175 210 2350 1958 57 121196G 1250 1042 112 121197G 225 187.5 2455 2046 57 121199G 1300 1083 114 121201G 200 240 2550 2125 59 121203G 1490 1242 115 121205G 225 270 2640 2200 65 121207G 1280 1067 148 121208G 250 300 2500 2083 70 121998G
DESCRIPTION
CT
121211G 121213G 121216G 121217G 121219G 121222G 121224G 121225G
PART NUMBERS
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
Wood Group ESP, Inc.
6-5/8" / 168.28 MM O.D. or Larger LENGTH WEIGHT PLUG-IN Ft M Lbs Kgs
111906 1017318 1054469
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
5
1.52
300
136
6.3
1.92
390
177
7.7
2.35
483
220
9.1
2.77
575
261
10.5
3.2
678
307
11.8
3.6
770
649
13.2 4.02
862
391
15.9 4.85 1047
475
18.7
1232
559
19.9 6.07 1287
584
21.4 6.52 1417
643
22.8 6.95 1514
687
24.2 7.38 1620
735
26.9 7.92 1833
832
29.6 9.02 2018
915
5.7
LENGTH Ft M 1.3 0.42 0.75 0.23 NA NA
WEIGHT Lbs Kgs 81 36.7 26 11.8 1.3 0.6
www.woodgroup-esp.com Page - 9
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 10
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. E37 SERIES MOTOR 3.75" / 95.25 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 45 37.5 730 608.3 48 48.5 75 62.5 1200 1000 80 850 708.3 90 75 1150 958.3 53
4-1/2" / 114.3 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT Ft M Lbs Kgs 172088G 172083G 16 4.9 685 311 172105G 172092G 24.4 7.4 1076 488 172043G 172044G 29.1 8.9 1294 587 172109G 172111G
DESCRIPTION BASE, MOTOR E37 BOLT ON FILTER ASSY STL BASE, MOTOR E37 BOLT ON FILTER ASSY CR BASE, MOTOR E37 BO FLTR TO SNR ASSY STL* BASE, MOTOR E37 BO FLTR TO SNR ASSY CR
PART NUMBERS 172052 172053 172054 172055
LENGTH Ft M 1.7 0.52 1.7 0.52 1.7 0.52 1.7 0.52
WEIGHT Lbs Kgs 26 11.8 26 11.8 29 13.2 29 13.2
PART NUMBERS 172045 172046 172116 172117
LENGTH WEIGHT Ft M Lbs Kgs 1.2 0.37 32.5 14.7 1.2 0.37 32.5 14.7 1.2 0.37 32 14.5 1.2 0.37 32 14.5
PART NUMBERS 172112 172113
LENGTH Ft M NA NA NA NA
WEIGHT Lbs Kgs NA NA NA NA
PART NUMBERS T9179
LENGTH Ft M NA NA
WEIGHT Lbs Kgs NA NA
*Special filter base used to attach TR3 sensors
DESCRIPTION HEAD, MOTOR E-37 W/LP STL CT BO ASSY* HEAD, MOTOR E37 W/LP CR CT BO ASSY* HEAD, MOTOR E37 NLP STL CT BO ASSY** HEAD, MOTOR E37 NLP CR CT BO ASSY** * For conversiont CT to UT motors with lock plates ** For conversion CT to UT motors without lock plates
DESCRIPTION KIT, ADAPTER TR4 SEAL/E37 MTR STL KIT, ADAPTER TR4 SEAL/E37 MTR 4SS
Additional Field Service Tool required DESCRIPTION TOOL, ALIGNMENT TDM INVL SPLN E37
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 11
Typical E-37 Motor Performace at 60 Hertz 3,600
120
3,500
100 % Amps
Speed
3,400
80 Power factor
Efficiency
3,300
60
3,200
40
3,100
20
3,000
0 20
40
60
80
100
120
% Rated Load
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 12
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. E56 SERIES MOTOR 5.62" / 142.75 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 200 166.7 1403 1169 86 250 208.3 1754 1462 86 1744 1453 104 300 250 2105 1754 86 2034 1695 104 350 291.7 2455 2046 86 2325 1937 104 400 333.3 2806 2338 86 2616 2180 104 450 375 500
7" / 177.8 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT CT Ft M Lbs Kgs UT 123882 16.7 5.1 1168 531 123760 123890 20.2 6.2 1413 642 123768 123896 123774 23.7 7.2 1680 764 123775 123897 123779 123901 27.2 8.3 1934 879 123780 123902 123782 123904 30.8 9.4 2195 998 123783 30.6 9.33 2195 998 123907 34.2 10.4 2450 111
416.7
TBD
DESCRIPTION HEAD, MOTOR E56 UT BO ASSY LH BASE, MOTOR E56 BO W/FILTER ASSY* BASE, MOTOR E56 BO BASE, SENSOR WIRE FILTER ASSY**
PART NUMBERS 123811 123651 153172
LENGTH Ft M 1.5 0.5 2.1 0.6 2.1
0.6
WEIGHT Lbs Kgs 88 40 65 30 65
30
* Equivalent of universal motor base, only with filter section. ** Special filter base used to attach TR5 Sensors
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 13
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 14
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 300 SERIES HTI MOTORS 3.75" / 95.25 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 7.5 6.2 410 342 10.5 8.7 390 342 315 262 12.5 15 400 333 387 322 19.5 16.2 630 525 330 275 22.5 18.7 440 367 730 608 370 308 25.5 21.2 500 417 630 525
AMPS 14 20.5 35.5 28 38 23 51.5 38.5 23 51 37 30
PART NUMBERS UT CT
103127G 113354G 113476G 103129G
103128G 113355G 113478G 103130G
LENGTH Ft M 6.4 1.95 8.3 2.53
WEIGHT Lbs Kgs 208 94.35 270 122.5
11.1
3.38
361
163.8
13.9
4.24
456
206.8
15.8
4.82
514
233.2
17.7
5.39
660
299.4
300 SERIES HTI - THD MOTORS 3.75" / 95.25 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 10 8.3 455 380 15 12.5 455 370 25 20.8 490 405 455 380 30 25 745 620 520 430 35 29.2 865 730 595 495 40 33.3 750 625
T NUMBERS AMPS UT 17 26 39 50 30 113436G 51 113349G 30 49 113803G 40
DESCRIPTION HEAD , MTR TR3-92 BOLT-ON KIT, BASE MTR TR3 Y-PT STL KIT, INSTALLATION TR3
Wood Group ESP, Inc.
CT
LENGTH Ft 6.4 8.3 11.1
M 1.95 2.53 3.38
13.9
4.24
456
206.8
15.8
4.82
514
233.2
17.7
5.39
660
299.4
113437G 113350G 113802G
PART NUMBERS 113268 1048610 1054444
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
LENGTH Ft M 1.1 0.34 0.5 0.15 NA NA
WEIGHT Lbs Kgs 208 94.35 270 122.5 361 163.8
WEIGHT Lbs Kgs 28 12.7 15 6.8 0.5 0.23
www.woodgroup-esp.com Page - 1
Wood Group ESP, Inc.
Wood Group ESP, Inc. Page - 2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. 400 SERIES HTI MOTORS 4.56" / 115.82 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 10 8.7 435 362 15 435 362 23 15 12.5 610 508 16 450 375 28.5 20 16.5 750 625 17 410 342 39 25 20.8 690 575 22 810 675 20 425 354 44.5 30 25 750 625 25.5 400 333 55 35 29.2 675 562 33 750 625 28 420 350 62 770 642 33 40 33.3 880 733 29 1295 1079 20 675 562 47 815 679 39 50 41.7 955 796 33 1070 892 31 1210 1008 27 640 533 59 810 675 47 60 50 970 808 39 1330 1108 29 1945 1621 20
DESCRIPTION
5-1/2" / 139.70 MM O.D. or Larger Casing LENGTH WEIGHT PART NUMBERS UT CT PLUG-IN Ft M Lbs Kgs 4.1 1.25 240 109 130362G 130568G 5.3 1.62 288 131 130001G 130002G 6.5 1.98 345 156 130003G 192597G 130004G 7.7 2.35 402 183 130005G 130006G 192599G 130007G 8.9 2.71 462 210 130008G 192528G 130009G 10.1 3.08 520 236 130010G 130011G 130012G 130013G 11.3 3.44 577 262 130014G 192601G 130015G 130016G 192529G 130017G 130018G 13.7 4.18 694 315 130019G 130020G 192530G 130021G 130038G 130022G 130039G 130023G 130040G 16.5 5.03 810 367 130024G 130041G 192694G 130025G
PART NUMBERS
HEAD , MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT, INSTALLATION TR4
Wood Group ESP, Inc.
110669 1008109 1054451
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.5 21 9.53 0.21 0.1
www.woodgroup-esp.com Page - 3
Wood Group ESP, Inc. 400 SERIES HTI MOTORS continued 4.56" / 115.82 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 540 450 82.5 750 625 60 70 58.3 945 787 47 1135 946 39 1310 1092 35 635 529 80 860 717 60 80 66.7 1085 904 46 1310 1092 39 2155 1796 24 710 592 81 960 800 59 1135 946 50 90 75 1220 1017 46 1460 1217 39 1930 1608 31 775 646 84 1075 896 59 100 83.3 1355 1129 46 2205 1837 28.5 1190 992 60 110 91.7 2380 1983 30 930 775 84 1040 867 76 120 100 1125 937 70 1295 1079 59 2245 1871 35
DESCRIPTION
5-1/2" / 139.70 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT PLUG-IN UT CT Ft M Lbs Kgs 130026G 130042G 130027G 130043G 18.4 5.61 885 402 130028G 130044G 130029G 130045G 192594G 130046G 130030G 120687G 120691G 130031G 130047G 20.8 6.34 994 451 130032G 130048G 130033G 130049G 130034G 192691G 120855G 120856G 130035G 130053G 130036G 130054G 192595G 23.2 7.07 1115 506 130037G 130055G 130502G 130544G 192531G 130503G 130504G 130545G 130505G 130546G 192376G 25.6 7.8 1295 588 130506G 130547G 192533G 130507G 130508G 130548G 192452G 28 8.53 1395 632 130509G 130528G 130549G 130529G 130550G 130530G 130563G 30.4 9.27 1500 681 120689G 120954G 192532G 130543G
PART NUMBERS
HEAD , MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT, INSTALLATION TR4
110669 1008109 1054451
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.5 21 9.53 0.21 0.1
Wood Group ESP, Inc.
The ESP Specialists
Page - 4
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. 400 SERIES HTI - THD MOTORS 4.56" / 115.82 MM O.D. HP VOLTS 60 Hz 50 Hz 60 Hz 50 Hz 15 12.5 505 421 20 16.5 675 562 30 25 870 725 780 650 35 29.2 915 762 495 412 45 37.5 870 725 770 642 50 41.7 885 737 1020 850 60 50 1505 1254 1245 1037 62.5 75 1410 1175 1540 1283 74.7 90 2260 1883 1320 1100 87.5 105 1520 1267 1525 1270 100 120 2505 2087 1695 1412 135 112.5 2240 1867 1575 1312 150 125 2565 2133 1385 1154 165 137.5 2765 2304 1505 1254 180 150 2610 2175
AMPS 20 20 23 28 25 59 34 42 36 39 27 41 36 39 27 52 47 52 32 52 41 61 38 80 40 79 47
DESCRIPTION
PART NUMBERS
Head, MTR TR4 BO ASSY KIT, BASE MTR TR4 BO Y-PT STL KIT INSTALLATION TR4
Wood Group ESP, Inc.
5-1/2" / 139.70 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT Ft M Lbs Kgs 140277G 4.1 1.25 240 108.9 140279G 5.3 1.62 288 131 140281G 6.5 1.98 345 155 140283G 7.7 2.35 402 183 140284G 140285G 8.9 2.71 462 210 140286G 140288G 10.1 3.08 520 236 140289G 140292G 11.3 3.44 577 262 140293G 140297G 13.7 4.18 694 315 140298G 140302G 140253G 16.5 5.03 810 368 140303G 140307G 140257G 18.4 5.61 885 402 140308G 140258G 140312G 140262G 20.8 6.34 994 451 140313G 140318G 140267G 23.2 7.07 1115 506 140319G 140322G 140270G 25.6 7.8 1295 588 140323G 140324G 140271G 28 8.53 1395 633 140325G 140329G 140275G 30.4 9.27 1500 681 140331G
110669 1008109 1054451
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
LENGTH Ft M 1.3 0.4 1 0.3 NA NA
WEIGHT Lbs Kgs 32 14.52 21 9.53 0.21 0.1
www.woodgroup-esp.com Page - 5
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Page - 6
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. 500 SERIES HTI MOTORS 5.44" / 138.20 MM O.D. (PLUG-IN: 5.56" / 141.22MM O.D) 6-5/8" / 168.28 MM O.D. or Larger HP VOLTS T NUMBERS LENGTH WEIGHT AMPS UT CT PLUG-IN 60 Hz 50 Hz 60 Hz 50 Hz Ft M Lbs Kgs 121861G 440 367 29 16.7 121862G 20 5 1.52 300 137 755 629 17 121863G 1020 850 12 121864G 435 362 45 25 30 121865G 6.3 1.92 390 177 710 592 28 121866G 1215 1012 16 121867G 435 362 60 121868G 730 608 36 33.3 40 7.7 2.35 483 219 121869G 880 733 30 121870G 1325 1104 20 121871G 450 375 72 121872G 725 604 45 41.7 50 121873G 9.1 2.77 575 261 905 754 35 121874G 1270 1058 25 121875G 161358G 1375 1146 22 121876G 425 354 91 121877G 645 537 59 121786G 136193G 870 725 45 50 60 10.5 3.2 678 308 121878G 970 808 40 121879G 1085 904 35 121881G 151524G 1320 1100 30 121882G 755 629 60 58.3 1015 846 70 121883G 11.8 3.6 770 349 45 121884G 1265 1054 35 121885G 865 721 60 66.7 1160 967 80 121707G 13.2 4.02 862 391 45 121886G 2180 1817 23
DESCRIPTION
PART NUMBERS 111906 1017318 1054469
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
LENGTH WEIGHT Ft M Lbs Kgs 1.3 0.42 81 36.7 0.75 0.23 26 11.8 NA NA 1.3 0.6
www.woodgroup-esp.com Page - 7
Wood Group ESP, Inc. 500 SERIES HTI MOTORS continued 5.40" / 137.16 MM O.D. (PLUG-IN: 5.56" / 141.22MM O.D) 6-5/8" / 168.28 MM O.D. or Larger HP VOLTS PART NUMBERS LENGTH WEIGHT AMPS UT CT PLUG-IN 60 Hz 50 Hz 60 Hz 50 Hz Ft M Lbs Kgs 121887G 141853G 705 587 90 121888G 121911G 835 696 76 100 83.3 1070 892 121889G 121912G 151811G 15.9 4.85 1047 471 60 121709G 121913G 1255 1046 50 121890G 131757G 2170 1808 29 121891G 121914G 855 712 88 121892G 121915G 1030 858 73 100 18.7 5.7 1232 554 120 121893G 121916G 151397G 1295 1079 59 121894G 132673G 2165 1804 33 121895G 121917G 925 771 88 19.9 6.07 1287 585 130 108.3 121896G 121918G 1125 937 73 121897G 121919G 985 821 90 140 116.7 1210 1008 21.4 6.52 1417 644 121711G 121920G 67 121898G 2015 1679 44 121899G 121921G 1075 896 87 150 151812G 22.8 6.95 1514 688 125 121922G 121713G 1240 1033 76 136446G 161357G 121900G 2105 1754 44 121901G 121923G 825 687 122 121928G 121715G 1115 929 88.5 160 133.3 24.2 7.38 1620 736 121902G 161361G 2003 1699 50 121903G 2185 1821 46 121924G 121904G 945 787 120 121905G 121925G 1275 1062 89 180 150 26.9 8.2 1833 833 121906G 1945 1621 59 121907G 2260 1883 50 121908G 121926G 1100 917 115 200 166.7 29.6 9.02 2018 917 121909G 2140 1783 54 121701G 121702G 1135 946 127 225 187.5 29.6 9.02 2018 917 151400G 121910G 2235 1862 64
DESCRIPTION
PART NUMBERS 111906 1017318 1054469
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
LENGTH WEIGHT Ft M Lbs Kgs 1.3 0.42 81 36.7 0.75 0.23 26 11.8 NA NA 1.3 0.6
Wood Group ESP, Inc.
The ESP Specialists
Page - 8
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. 500 SERIES HTI - THD MOTORS 5.40" / 137.16 MM O.D. HP VOLTS T NUMBERS AMPS UT 60 Hz 50 Hz 60 Hz 50 Hz 141088G 510 425 37 30 25 141090G 1190 992 15 141091G 510 425 58 45 37.5 141093G 1420 1183 21 141096G 1025 854 39 60 50 141097G 1545 1287 26 141100G 1055 879 45 75 62.5 141102G 1600 1333 28 141106G 1130 942 52 90 75 141108G 1540 1283 39 141110G 1180 983 58 105 87.5 141111G 1475 1229 45 141113G 1355 1129 58 120 100 141114G 2540 2117 30 141118G 1465 1221 65 150 125 141119G 2350 1958 37 141121G 1200 1000 94 180 150 141123G 2525 2104 43 141125G 195 162.5 1310 1092 87 141126G 1150 958 116 210 175 141128G 2350 1958 57 141129G 1255 1046 112 225 187.5 141131G 2455 2046 57 141133G 1300 1083 114 240 200 141135G 2550 2125 59 141137G 1485 1238 115 270 225 141139G 2640 2200 65 1285 1067 148 300 250 141141G 2500 2083 70
DESCRIPTION
CT
141028G 141030G 141048G 141049G 141066G 141069G 141086G 121395G
PART NUMBERS 111906 1017318 1054469
Head, MTR TR5 UT BO ASSY KIT, BASE MTR TR5BO Y-PT STL KIT INSTALLATION TR5
Wood Group ESP, Inc.
6-5/8" / 168.28 MM O.D. or Larger LENGTH WEIGHT PLUG-IN Ft M Lbs Kgs
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
5
1.52
300
136
6.3
1.92
390
177
7.7
2.35
483
220
9.1
2.77
575
261
10.5
3.2
678
307
11.8
3.6
770
649
13.2 4.02
862
391
15.9 4.85 1047 475 18.7
5.7
1232 559
19.9 6.07 1287 584 21.4 6.52 1417 643 22.8 6.95 1514 687 24.2 7.38 1620 735 26.9 7.92 1833 832 29.6 9.02 2018 915
LENGTH WEIGHT Ft M Lbs Kgs 1.3 0.42 81 36.7 0.75 0.23 26 11.8 NA NA 1.3 0.6
www.woodgroup-esp.com Page - 9
Wood Group ESP, Inc.
The ESP Specialists
Page - 10
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. E37 HTI SERIES MOTOR 3.75" / 95.25 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 45 37.5 587 489 53 75 62.5 978 815 53 90 75 1150 958.3 53
4-1/2" / 114.3 MM O.D. or Larger Casing PART NUMBERS LENGTH WEIGHT UT CT Ft M Lbs Kgs 172119G 172121G 16 4.9 685 311 172123G 172125G 24.4 7.4 1076 488 172109G 172111G 29.1 8.9 1294 587
815
DESCRIPTION BASE, MOTOR E37 BOLT ON FILTER ASSY STL BASE, MOTOR E37 BOLT ON FILTER ASSY CR BASE, MOTOR E37 BO FLTR TO SNR ASSY STL* BASE, MOTOR E37 BO FLTR TO SNR ASSY CR
PART NUMBERS 172052 172053 172054 172055
LENGTH Ft M 1.7 0.52 1.7 0.52 1.7 0.52 1.7 0.52
WEIGHT Lbs Kgs 26 11.8 26 11.8 29 13.2 29 13.2
PART NUMBERS 172045 172046 172116 172117
LENGTH WEIGHT Ft M Lbs Kgs 1.2 0.37 32.5 14.7 1.2 0.37 32.5 14.7 1.2 0.37 32 14.5 1.2 0.37 32 14.5
PART NUMBERS 172112 172113
LENGTH Ft M NA NA NA NA
WEIGHT Lbs Kgs NA NA NA NA
PART NUMBERS T9179
LENGTH Ft M NA NA
WEIGHT Lbs Kgs NA NA
*Special filter base used to attach TR3 sensors
DESCRIPTION HEAD, MOTOR E-37 W/LP STL CT BO ASSY* HEAD, MOTOR E37 W/LP CR CT BO ASSY* HEAD, MOTOR E37 NLP STL CT BO ASSY** HEAD, MOTOR E37 NLP CR CT BO ASSY** * For conversiont CT to UT motors with lock plates ** For conversion CT to UT motors without lock plates
DESCRIPTION KIT, ADAPTER TR4 SEAL/E37 MTR STL KIT, ADAPTER TR4 SEAL/E37 MTR 4SS
Additional Field Service Tool required DESCRIPTION TOOL, ALIGNMENT TDM INVL SPLN E37
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 11
Typical E-37 Motor Performace at 60 Hertz
3,600
120
3,500
100
3,400
80
Speed (RPM )
Power factor
Efficiency
3,300
60
3,200
40
3,100
20
3,000 20
40
60
80
100
% Am ps/Efiiciency/Power Factor
% Amps
Speed
0 120
% Rated Load
Wood Group ESP, Inc.
The ESP Specialists
Page - 12
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. E56 HTI - SERIES MOTOR 5.62" / 142.75 MM O.D. HP VOLTS AMPS 60 Hz 50 Hz 60 Hz 50 Hz 200 166.7 1403 1169 86 250 208.3 1754 1462 86 1744 1453 104 250 300 2105 1754 86 2034 1695 104 350 291.7 2455 2046 86 2325 1937 104 400 333.3 2806 2338 86 450 375 2616 2180 104 500
PART NUMBERS UT CT 123760 123882 123768 123890 123774 123896 123775 123897 123779 123901 123780 123902 123782 123904 123783 123907
416.7
LENGTH Ft M 16.7 5.1 20.2 6.2
WEIGHT Lbs Kgs 1168 531 1413 642
23.7
7.2
1680 764
27.2
8.3
1934 879
30.8 9.4 2195 998 30.6 9.33 2195 998 34.2 10.4 2450 111
TBD
DESCRIPTION HEAD, MOTOR E56 UT BO ASSY LH BASE, MOTOR E56 BO W/FILTER ASSY* BASE, MOTOR E56 BO BASE, SENSOR WIRE FILTER ASSY**
PART NUMBERS 123811 123651 153172
LENGTH Ft M 1.5 0.5 2.1 0.6 2.1
0.6
WEIGHT Lbs Kgs 88 40 65 30 65
30
* Equivalent of universal motor base, only with filter section. ** Special filter base used to attach TR5 Sensors
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 13
Wood Group ESP, Inc.
Wood Group ESP, Inc.
The ESP Specialists
Page - 14
Product Catalog - Motors - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc.
MOTOR SHROUDS ENCAPSULATED PUMP SYSTEM MATERIALS OF CONTRUCTION Two material types are available, duplex stainless steel (SS) and carbon steel (CS). Engineering should also be consulted for applications with wellbore deviation in excess of 45° or where the maximum dogleg severity (DS) exceeds 5°/100 ft. APPLICATION RATING BURST PRESSURE
COLLAPSE PRESSURE PSI
MAXIMUM MAXIMUM MAXIMUM TENSION TEMPERATURE O.D. INCHES LBS DEGREE
Well Casing Size PSI 7” CASING 5,000 4,800 12,000 260 5.76 7” CASING 5,000 4,200 12,000 260 5.76 5 1/2” CASING 5,000 4,800 10,000 260 4.66 5 1/2” CASING 5,000 4,200 10,000 260 4.66 Part numbers for different sizes Encapsulated Pump System are given in table below. Since each application will be unique, Wood Group ESP’s engineering department should be consulted for the quantity of the shroud material and other necessary components ordered.
DESCRIPTION SHROUD HANGER SHROUD TOP HANGER SCREWS O-RING BACK-UP RINGS EUE PIN EUE PIN SECTION SECTION THROUGH SYSTEM 3/8” 8rd EUE MOTOR BASE
7”SS 147019 147023 147022 705247 145394 147021 147376 147039 147029 145395 145772 145392
PART NUMBER 7”CS 5 1/2” SS 145759 147016 145761 147018 147022 147017 705247 705241 145394 145400 145763 147024 145766 147060 145768 147042 145770 147041 145395 145395 145773 145772 145392 145401
5 1/2” CS 145760 145762 147017 705241 145400 145764 145767 145769 145771 145395 145773 145401
Wood Group ESP, Inc.
The ESP Specialists
Page - 2
Product Catalog - Motors / Motor Shrouds - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com
Wood Group ESP, Inc. Seal Section
Application Guidelines Seal Bags Elastomer seal bags are available in three materials HSN, FKM* and Aflas. The durability of the bag material depends on the temperature and the environment to which it is subjected. The following chart should be followed when selecting the right bag material for well application. Wood Group ESP’s standard bag material is HSN. More robust materials are also available to meet specific applications. Material Maximum BHT (applies to seal sections only) Maximum Operating Temperature Chemical Water/oil
HSN
FKM*
Aflas
175°F
300°F
350°F
275°F
400°F
450°F
HSN Excellent Good Excellent Fair
FKM* Good Poor Poor Poor
Aflas Excellent Good Excellent Excellent
Aromatic hydrocarbon (Xylene, Toluene, etc.)
Fair
Good or Fair
Fair
Steam (geothermal applications)
Fair
Fair
Excellent**
Carbon Dioxide (CO2) Hydrogen Sulfide (H2S)
Amines
*FKM is the abbreviation of fluoroelastomers. One common fluoroelastomer is Viton, which is a trade name of DuPont. To call all fluoroelastomers Viton is common, but incorrect and has been addressed legally by DuPont. **EPDM, perfluoroelastomer, is also excellent in steam applications, depending on the temperature range and chemicals.
Ratings: Excellent – Long term resistance (very low swell, maintains very high physical properties) Good – Long term resistance (moderate swell, maintains very high physical properties) Fair – Depends upon exposure time and temperature (good short term resistance) Poor – No resistance even in the short term Note: An Application Engineer should be consulted on applications where the equipment might be subjected to a fluid with constituents other than listed in table.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October 2009
www.woodgroup-esp.com Page - 1
Wood Group ESP, Inc.
Thrust Bearing Load Calculations for all Floater Pumps Floater pump thrust comes from the pump differential pressure operating on the cross-sectional area of the pump shaft. To calculate maximum floater pump thrust use the following procedure: 1. Look in the engineering data section of the product catalog and locate the pump shaft area (A) in sq. in. 2. Look up the pump performance curve in the product catalog and locate the shut-in pump head (Hd) in ft/stage at your maximum operating frequency. 3. Calculate the maximum pump thrust using: lbf = Ft/stage x .433 x SG x A x Nstages Where: Nstages is the number of floater pump stages, SG is the pumped fluid specific gravity
Thrust Bearing Load Calculations for all Compression Pumps Compression pump thrust comes from both the discharge pressure operating across the pump shaft area plus the sum of the pressure differential across each pump stage acting across the stage skirt areas minus the fluid momentum imparted on the stage by the moving fluid. The pump thrust is a function of the fluid rate and increases as the flow rate decreases. WGESP publishes compression pump thrust at shut-in conditions (the maximum). This published value already includes the pump shaft thrust. To calculate maximum compression pump thrust used the following algorithm: 1. Look in the engineering data section of the product catalog. It contains the maximum compression pump thrust in lbf/stage for both 60 and 50 Hz operation. (This is at shut-in) 2. The pump thrust at different operating frequencies can be estimated from: lbf(n) = lbf(60) x (n/60) 2 3. Calculate the maximum pump thrust using: lbf = lbf/stage x Nstages Where: Nstages = The number of compression pump stages
Thrust Bearing Load Calculations for Combination Pumps When you have a combination of floater and compression pump stages, calculate the thrust for each type of pump independently and then add the results.
Thrust Bearing Selection Compare the maximum pump thrust to the thrust bearing thrust limit. Note this is a function of temperature and motor oil used for high load bearings. Choose a thrust bearing that has a higher thrust limit than the thrust generated by the pump. Note compression pumps will almost always require a high load bearing and engineering guidelines call for use of a high load bearing when installing compression pumps.
Wood Group ESP, Inc. Page - 2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. TR3 Series Length
Description
Weight
Ft. M. Lbs. Kgs. 5.10 1.6 90.0 41 SEAL,TR3 STD 5.10 1.6 90.0 41 SEAL,TR3 STD HL,HT ENGINEERING DATA - TR3 SERIES 60 HZ OPERATION 50 HZ OPERATION 3.375 IN HOUSING DIAMETER HOUSING DIAMETER SHAFT DIAMETER .750 IN SHAFT DIAMETER STANDARD 160 HP SHAFT LIMIT STANDARD SHAFT LIMIT HIGH STRENGTH 256 HP HIGH STRENGTH
PART NO. 913020 113277
85.85 MM 19.05 MM 133 HP 213 HP
TR387 SERIES Length Weight PART NO. Lbs. Kgs. Ft. M. 4.50 1.4 101 46 116613 SEAL,TR387 SBG PFSB STL HL-HT AFLAS SEAL,TR387 DBG PFDB STL HL-HT AFLAS 6.10 1.9 195 88 116646 ENGINEERING DATA - TR387 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 98.30 MM 3.87 IN HOUSING DIAMETER SHAFT DIAMETER 22.23 MM 0.875 SHAFT DIAMETER SHAFT LIMIT 213 HP STANDARD 256 HP SHAFT LIMIT STANDARD 342 HP HIGH STRENGTH 410 HP HIGH STRENGTH Description
TR3 Seal Thrust Bearing Capacities
Thrust Load (lb)
2900
40, 50, 60, & 70 Hz - 2750 lb
2700 2500
30 Hz - 2400 lb
2300 2100 1900
20 Hz - 1800 lb 1700 0
50
100
150
200
250
300
350
400
Motor Operating Temp. (°F) Note: High Load (HL) bearing shown using ESP #6 oil.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 3
Wood Group ESP, Inc. TR4 Series Length
Weight
PART NO. Ft. M. Lbs. Kgs. 5.30 1.6 130.0 59 140691 SEAL,TR4 STD HL HT 98L AFLAS 1.6 130.0 59 140692 5.30 SEAL,TR4 STD HL HT 98L HSS AFLAS 130.0 59 190147 SEAL,TR4 STD HL-HT 98L UHSS 5.30 1.6 SEAL,TR4 STD HL-HT 98L UHSS AFLAS 5.30 1.6 130.0 59 170787 165.0 SEAL,TR4 SBG PFSB STL 4.50 1.4 75 1008275 4.50 1.4 165.0 75 1008267 SEAL, TR4 SBG PFSB CR SEAL, TR4 SBG PFSB HL HT STL AFLAS 4.50 1.4 165.0 75 120377 4.50 1.4 165.0 75 130860 SEAL, TR4 SBG PFSB HL HT STL AR AFLAS SEAL,TR4 DBG PFDB STL 6.10 1.9 195.0 88 1008291 6.10 1.9 195.0 88 130853 SEAL,TR4 DBG PFDB AR CR 6.10 1.9 195.0 88 160452 SEAL,TR4 DBG PFDB AR HL HT 6.10 1.9 195.0 88 170226 SEAL,TR4 DBG PFDB HL STL UHSS 6.10 1.9 195.0 170999 SEAL,TR4 DBG PFDB HL-HT STL UHSS AFLAS 88 ENGINEERING DATA - TR4 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 101.60 MM 4.00 IN HOUSING DIAMETER .875 IN SHAFT DIAMETER SHAFT DIAMETER 22.23 MM SHAFT LIMIT 213 HP STANDARD 256 HP SHAFT LIMIT STANDARD 342 HP HIGH STRENGTH 410 HP HIGH STRENGTH 522 HP 435 HP ULTRA HIGH STRENGTH ULTRA HIGH STRENGTH Description
TR4 Seal Thrust Bearing Capacities 9000
70 Hz - 8800 lb
Thrust Load (lb)
8000
60 Hz - 7000 lb
7000
50 Hz - 5800 lb 6000
40 Hz - 4800 lb 5000
30 Hz - 4000 lb
4000
20 Hz - 3200 lb
3000 0
100
200
300
400
Motor Operating Temp. (°F) Note: High Load (HL) bearing shown using ESP #6 oil.
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Page - 4
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. TR5 SERIES Weight
Length
PART NO. M. Lbs. Kgs. Ft. 1.7 230.0 104 548220 5.60 SEAL, TR5-AR LBYR HL 2CH STL HSN 1.7 5.60 230.0 104 548065 SEAL,TR5-AR L/L HL-HT STL SST HB HSS 200.0 91 1019595 SEAL, TR5 SBG PFSB STL 4.40 1.3 1.3 200.0 91 SEAL, TR5 SBG PFSB STL HL HT AFLAS 4.40 141457 1.9 250.0 113 1019611 SEAL, TR5 DBG PFDB STL 6.30 6.30 2.9 250.0 113 121433 SEAL, TR5 DBG PFDB STL HL HSN 6.30 3.9 250.0 113 141595 SEAL, TR5-AR DBG PFDB HL STL HSN 6.30 4.9 250.0 113 121741 SEAL, TR5 DBG PFDB STL HL HT AFLAS 5.60 540112 1.7 240.0 SEAL, TR5-AR B/L HL STL AFLAS 109 5.60 1.7 230.0 548063 104 SEAL,TR5-AR B/L HL-HT SST H&B HSS 9.12 2.8 420.0 548279 190 SEAL,TR5-AR L/2BP HL-HT PFU SST H&B HSS 9.12 2.8 420.0 548490 190 SEAL,TR5-AR L/2BP HL-HT AFLAS HSS 9.70 3.0 420.0 141238 SEAL, TR5-AR 2BP/2L HL STL HSN 190 9.70 420.0 141812 190 3.0 SEAL, TR5-AR 2BP/2L HL STL AFLAS 9.70 548083 SEAL,TR5-AR 2BP/2L HL HSN STL HSS LH 190 3.0 420.0 ENGINEERING DATA - TR5 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 136.50 MM 5.125 IN HOUSING DIAMETER SHAFT DIAMETER 30.20 MM 1.188 IN SHAFT DIAMETER AR SHAFT DIAMETER 1.375 IN AR SHAFT DIAMETER 34.90 MM SHAFT LIMIT 531 HP STANDARD 637 HP SHAFT LIMIT STANDARD 849 HP HIGH STRENGTH 1019 HP HIGH STRENGTH STANDARD STANDARD AR SHAFT LIMIT 637 HP AR SHAFT LIMIT 531 HP HIGH STRENGTH 1019 HP HIGH STRENGTH 849 HP Description
TR5 Seal Thrust Bearing Capacities 70 Hz - 10400 lb
Thrust Load (lb)
12000 11000
60 Hz - 11600 lb
10000 9000
50 Hz - 9200 lb
8000
40 Hz - 8000 lb
7000 6000
30 Hz - 6000 lb
5000
20 Hz - 4200 lb
4000 0
50
100
150
200
250
300
350
400
Motor Operating Temp. (°F) Note: High Load (HL) bearing shown using ESP #6 oil.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page - 5
Wood Group ESP, Inc. TR562 SERIES Length
Description
Weight
PART NO.
Ft.
M.
Lbs.
Kgs.
SEAL,TR562-AR 2BP/2L HL HSN STL HSS CCW, LEFT HAND THREAD
9.90
3.01
420.0
190
548301
SEAL,TR562-AR 2BP/2L HL HSN SST HD CCW, HSS, SST HEAD ONLY, LEFT HAND THREAD
9.90
3.01
420.0
190
548302
ENGINEERING DATA - TR562 SERIES 60 HZ OPERATION 50 HZ OPERATION HOUSING DIAMETER 136.50 MM 5.125 IN HOUSING DIAMETER 1.375 IN SHAFT DIAMETER SHAFT DIAMETER 34.93 MM SHAFT LIMIT 575 HP STANDARD 690 HP SHAFT LIMIT STANDARD 917 HP HIGH STRENGTH 1100 HP HIGH STRENGTH
TR562 Seal Thrust Bearing Capacities 25000
70 Hz - 24000 lb
Thrust Load (lb)
23000 21000
60 Hz - 20800 lb
19000
50 Hz - 16800 lb
17000 15000
40 Hz - 14000 lb
13000 11000
30 Hz - 11200 lb
9000 7000
20 Hz - 8000 lb 0
100
200
300
400
Motor Operating Temp. (°F)
Note: High Load (HL) bearing shown using ESP #6 oil.
Wood Group ESP, Inc. Page - 6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Seal Sections - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SMARTGUARD SENSORS Surface Unit Options - available options for the surface interface unit DESCRIPTION OPTION, EVENT LOG EXPANSION OPTION, MEMORY EXPANSION, 7 DAY OPTION, MEMORY EXPANSION, 14 DAY OPTION, MEMORY EXPANSION, 35 DAY OPTION, I/O EXPANSION OPTION, RADIO / RS485 MULTI-DROP COMMUNICATIONS
PART NUMBER 129134 129119 129120 129121 129125 129122
Downhole Sub-Assemblies - replacement parts - does not include motor adapter heads DOWNHOLE SUB-ASSEMBLY, STL 140470 SmartGuard III DOWNHOLE SUB-ASSEMBLY, SST 140471 DOWNHOLE SUB-ASSEMBLY, STL 800758 SmartGuard V DOWNHOLE SUB-ASSEMBLY, SST 800759 DOWNHOLE SUB-ASSEMBLY, STL 800777 SmartGuard VI DOWNHOLE SUB-ASSEMBLY, SST 800778
Motor Adapter Heads - replacement parts - does not include the downhole sub-assemblies HEAD, SMARTGUARD TR3 ASSY, STL 800462 HEAD, SMARTGUARD TR3 ASSY, SST 800459 HEAD, SMARTGUARD TR4 ASSY, STL 800463 HEAD, SMARTGUARD TR4 ASSY, SST 800460 HEAD, SMARTGUARD TR5 ASSY, STL 800464 HEAD, SMARTGUARD TR5 ASSY, SST 800461 X-OVER, SMARTGUARD TO CENTRILIFT MTR, STL 800489 X-OVER, SMARTGUARD TO CENTRILIFT MTR, SST 800525
Complete Systems - assembled with minimum parts required for service TR3 SMARTGUARD III SYSTEM, STL TR3 SMARTGUARD III SYSTEM, SST TR4 SMARTGUARD III SYSTEM, STL SmartGuard III TR4 SMARTGUARD III SYSTEM, SST TR5 SMARTGUARD III SYSTEM, STL TR5 SMARTGUARD III SYSTEM, SST
113626 113627 160476 160477 157061 157062
Pump Discharge Subs and Auxiliary Equipment
SmartGuard VI
SUB, DISCHARGE 2 7/8”, STL SUB, DISCHARGE 2 7/8”, SST SUB, DISCHARGE 3 1/2”, SST SUB, DISCHARGE 4 1/2”, STL SUB, DISCHARGE 5 1/2", STL, BUTTRESS THREAD VALVE, FLOW 1/4” MALE - 1/4”, SWAGELOK TUBING, 0.250” OD X 0.049” WL, 316 SST SPECIFY LENGTH
Wood Group ESP, Inc. Page-2
The ESP Specialists
800620 800629 800677 800751 800750 800646 800602
www.woodgroup-esp.com
Product Catalog - Downhole Sensing Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. MOTOR LEAD CABLE 300 SERIES DESCRIPTION
CABLE,MLC TR3 KELTB
SIZE
#6
TYPE ARMOR
MONEL
Length Ft. 30 40 55 70 90 110
M. 9.14 12.19 16.76 21.34 27.43 33.53
Weight Lbs. 25 33 45 58 74 91
Kgs. 11.34 14.97 20.41 26.31 33.57 41.28
PART NO. 113388 113389 113390 113391 113392 113393
400 SERIES DESCRIPTION
SIZE
TYPE ARMOR
CABLE,MLC TR4 HT PLUG-IN KELB #6
MONEL
CABLE,MLC TR4 HT KELB
Length Ft. 30 42 58 74 95 110 30 40 55 70 90 110
M. 9.14 12.80 17.68 22.56 28.96 33.53 9.14 12.19 16.76 21.34 27.43 33.53
Weight Lbs. 31 43 60 76 98 113 31 41 57 72 93 113
Kgs. 14.06 19.50 27.22 34.47 44.45 51.26 14.06 18.60 25.86 32.66 42.18 51.26
PART NO. 458543 458544 458545 458546 458547 458548 136719 136720 136721 136722 136723 136724
500 SERIES DESCRIPTION
SIZE
TYPE ARMOR
CABLE,MLC TR5 HT PLUG-IN KELB #4
MONEL
CABLE,MLC TR5 HT KELB
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Downhole Cables - Copyright Wood Group ESP, Inc. - October, 2009
Length Ft. 30 42 58 74 95 110 30 40 55 70 90 110
M. 9.14 12.80 17.68 22.56 28.96 33.53 9.14 12.19 16.76 21.34 27.43 33.53
Weight Lbs. 38 54 74 95 122 141 38 51 70 90 115 141
Kgs. 17.24 24.49 33.57 43.09 55.34 63.96 17.24 23.13 31.75 40.82 52.16 63.96
PART NO. 151557 151558 151559 151560 151561 151562 145016 145017 145018 145019 145020 145021
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. CABLE DESCRIPTION FLAT PL190 3KV FLAT PL205 5KV
FLAT PL225 5KV
FLAT PL450 5KV
FLAT PL400 MLE 4KV
ROUND PL205 5KV ROUND PL300 5KV
WIRE SIZE
CONSTRUCTION
INSULATION
JACKET
ARMOR
DIMENSION
WEIGHT Lbs/Ft
Solid
PP
PP
GALV
Solid
PP
NBR
GALV
0.54 x 1.37 0.73 x 1.92 0.70 x 1.83
0.85 1.70 1.40
741064 145809 145808
#4
0.64 x 1.67
1.10
145864
#2 #4 #1 #2
0.67 x 1.74 0.61 x 1.58 0.65 x 1.69 0.62 x 1.59
2.00 1.60 2.10 1.90
155000 136800 145819 145818
#4
0.56 x 1.43
1.50
145817
#2 #4 #6 6 Low Profile #1
0.54 x 1.48 0.48 x 1.26 0.44 x 1.13
1.72 1.28 1.03
741052 925248 925255
0.37 x 0.94
1.28
1051499
1.34 DIA
1.70
145805
1.50 1.20 1.75 1.53
145804 145803 145813 145812
1.19
145811
16MM2 #1 #2
#2 #4 #1 #2 #3
Wood Group ESP, Inc. Page-2
Solid
PP
Solid
EPDM
Solid
EPDM
Solid Stranded/Compacted Or Solid
LEAD
GALV
LEAD
GALV
LEAD
MONEL
PP
NITR
GALV
EPDM
EPDM EPDM
GALV GALV
1.28 DIA 1.16 DIA 1.39 DIA 1.31 DIA
EPDM
GALV
1.18 DIA
EPDM EPDM
The ESP Specialists
PART NO.
www.woodgroup-esp.com
Product Catalog - Downhole Cables - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. CABLE ACCESSORIES CABLE CLAMPS Weight DESCRIPTION CLAMP,CABLE STL 22” BLACK CLAMP, CABLE STL 32” BLACK CLAMP, CABLE SST 22” CLAMP, CABLE SST 32” CLAMP, CABLE MNL 22” CLAMP, CABLE MNL 32” SEALER,BANDING TOOL TENSIONER, BANDING TOOL SNIPS, METAL CUTTING 1-3/8” CUT
PART NO.
Lbs. 0.20 0.23 0.20 0.23 0.20 0.23 4.50 5.80 0.90
Kgs. 0.09 0.10 0.09 0.10 0.09 0.10 2.04 2.63 0.41
067587 067595 208496 208504 925644 925651 560763 562983 2642042
100 80 55
45.36 36.29 24.95
127618 127617 127619
0.05
0.02
160242
5.10 5.10
2.31 2.31
935643 145993
430 195.05
925222
115 150
925552 T777
BANDING MATERIAL BY THE COIL BANDING, CABLE STL 3/4X.020/COIL BANDING, CABLE SST 3/4X.020/COIL BANDING, CABLE MNL 3/4X.020/COIL
SADDLES SADDLE, CABLE #6 & #8 UNARMORED
FLAT CABLE GUARDS GUARD, CABLE 3KV GALV 8FT #1-#6 GUARD, CABLE 3KV SST 8FT #1-#6
CABLE REEL SUPPORT SUPPORT CABLE REEL
CABLE GUIDE WHEEL WHEEL, CABLE GUIDE 36”DIA #8-#1/0 RD/FT WHEEL, CABLE GUIDE 48”DIA #8-#1/0 RD/FT
52.16 68.04
CABLE REELS NOM SIZE 50.0 66.0 78.0 78.0 84.0 90.0
FLANGE DIAMETER 50 IN 66 IN 78 IN 78 IN - Heavy Duty 84 IN 90 IN
Wood Group ESP, Inc.
DRUM DIA. 30.0 33.0 35.0 42.0 35.0 42.0
TRAVERSE WIDTH 40.0 40.0 54.0 57.0 54.0 57.0
The ESP Specialists
Product Catalog - Downhole Cables - Copyright Wood Group ESP, Inc. - October, 2009
OVERALL WIDTH 46.0 46.0 60.0 64.0 60.0 64.0
Weight Lbs. Kgs. 331 150.14 441 200.04 772 350.18 1037 470.38 992 449.97 1248 566.09
PART NO. 741101 741102 741103 132688 741104 741105
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
CABLE REEL CAPACITIES ROUND CABLES (Feet per Reel) REEL SIZE CABLE TYPE
PL205
PL300
PART NUMBER
CABLE SIZE
145805 145804 145803 145813 145812 145811
1 AWG 2 AWG 4 AWG 1 AWG 2 AWG 4 AWG
66”
78”
2500 3000 3100 2400 3943 4888
6500 6700 7800 5500 7179 8898
78” Heavy Duty 6500 6700 7800 5500 7179 8898
84”
90”
7700 8900 10200 6800 9066 11237
10000 10300 12600 8800 10953 13577
FLAT CABLES (Feet per Reel) PL190
741064
16 MM2
10300
18000
24000
25000
29000
PL205
145809 145808
1 AWG 2 AWG 4 AWG 2 AWG 4 AWG 1 AWG 2 AWG 4 AWG
3451 4300
6283 9000
6283 10200
7935 12000
9587 14500
5300 4042 5200
11700 5520 7100
12100 7619 9800
15700 7619 9800
18900 8940 11500
3000 3400
6100 6900
8500 9600
8500 9600
9900 11200
4300
8600
12000
12000
14000
PL225
PL450
145864 155000 136800 145819 145808 145807
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Downhole Cables - Copyright Wood Group ESP, Inc. - October, 2009
®
Vector VII Product Data Book
Wood Group ESP 5500 S.E. 59th Street Oklahoma City, OK 73135 Tel 405-670-1431 www.woodgroup-esp.com
TERM DEFINITIONS TERM °C °F
Degrees Farenheit
AC
Alternating current
ASD COMM
Adjustable speed drive Communications
DC
Direct current
DPF
Displacement power factor
ESP
Electric submersible pump
I/O
Inputs / Outputs
IEC
International electric code
IGBT
Insulated gate bi-polar transistor
ISO
International Organization for Standardization
LCD
Liquid crystal display
MODBUS PI PCP SCADA
©
DEFINITION Degrees Celcius
Serial Communication Protocol Proportional Integral Progressing cavity pump Supervisory Control and Data Acquisition
SPS
Surface pumping systems
THD
Total harmonic distortion
TVSS
Transient voltage surge suppression
VAC
Volts AC
VDC
Volts DC
VFD
Variable frequency drive
VSD
Variable speed drive
VSG®
Variable Sinewave Generator
Wood Group-ESP 2009
2
TABLE OF CONTENTS PAGE NUMBER
TOPIC Term Definitions
2
Safety Notice
4
Introduction
5
Drive Description
5
Vector® VII Product Summary
6
Installation Examples
8
Catalog Number Explanation
9
Vector® VII without VSG® Catalog Numbers - 60 Hertz
10
Vector® VII with VSG® Catalog Numbers - 60 Hertz
11
Vector® VII without VSG® Catalog Numbers - 50 Hertz
12
Vector® VII with VSG® Catalog Numbers - 50 Hertz
13
Vector® VII Factory Installed Options
14
Manufacturer Qualifications and Certifications
15
General Specifications / Operating Conditions / Design Features
15
Operator Panel
20
Surface Pumping Systems (SPS™)
29
Input Harmonic Mitigation
30
Basic 12 Pulse and 18 Pulse Drive Schematics
31
Output Harmonic Mitigation
32
Grounding and Bonding / Typical 480 VAC Drive Installation
33
Generator Requirements
34
Dimensions and Weights
36
©
Wood Group-ESP 2009
3
SAFETY NOTICE Wood Group ESP, Inc. places a high priority upon personnel safety. Personnel performing maintenance upon drives should be properly trained and follow all safety procedures to prevent injury. Drives may cause serious injury if proper safety precautions, equipment, and installation procedures are not used. Units should always be grounded and confirmation of ground connection and continuity be established prior to performing any work or service. Be sure to consult user’s manual before installing, energizing, or operating equipment. Installation should always conform to local codes, regulations, or other authorities governing electrical equipment.
©
Wood Group-ESP 2009
4
INTRODUCTION This document provides a descriptive overview of the Vector® VII Variable Speed Drive (VSD) available from Wood Group ESP. Information is provided on available ratings, physical size, product features, general operation, and available options. Additional details regarding drive set-up, operation, and troubleshooting are available in the Vector VII Variable Speed Drive User’s Manual. The descriptions and information contained in this publication are for informational purposes only and should not be used to install, set-up, program, or operate the Vector VII drive. Note: This publication describes the standard Vector VII Variable Speed Drive and includes descriptions of the most common drive options and modifications. Specific features may be added (or disabled) from the product depending on the specific application. All specifications and information contained in this publication are subject to change without notice. DRIVE DESCRIPTION The Vector VII Variable Speed Drive is designed specifically for oil-field pumping applications including electrical submersible pumps (ESP) and surface pumping systems (SPS). Vector VII drives are available in ratings from 104 KVA to1500 KVA. They are provided in rugged outdoor rated enclosures designed for a wide variety of environments ranging from arctic to desert conditions. Application specific software and a Wood Group ESP Custom Operator Control Panel combine to optimize pump control while simplifying drive operation. Vector VII uses the latest Insulated Gate Bipolar Transistor (IGBT) technology in combination with surface mount printed circuit boards to create a VSD of the highest reliability, and small physical size. Fixed voltage, three-phase AC input power is first converted to a fixed DC bus voltage by the input rectifier section of the drive. That fixed DC bus voltage is then processed by the inverter section to produce a sine coded variable voltage, variable frequency output to control the speed of the motor. For ESP applications, the Vector VII Variable Speed Drive is available with integrated VSG® Technology. With VSG Technology the drive output voltage waveform is a near perfect sinewave which results in improved motor performance, extended motor run life, extended motor cable life, and increased operational efficiency in the driven equipment. Vector VII drives with VSG (Variable Sinewave Generation) technology can successfully operate with motor cable lengths up to 15,000 ft. User adjustments include operating speed, acceleration and deceleration rates, motor overload protection settings, auto restarts, time delays, and stopping methods. Control methods include frequency control, current control, pressure control, or analog follower (Analog 1 = 0-10 VDC, Analog 2 = 0-10 VDC or 4-20 mA) capability.
©
Wood Group-ESP 2009
5
VECTOR VII PRODUCT SUMMARY Standard Drive Features: • • • • • • • • • • • • • • • • • •
Ratings from 104 KVA to 1500 KVA. Specifically designed for oil field pumping applications. NEMA 3R outdoor enclosure, rugged (10 Gauge) steel construction with compact footprint. Enclosure base pre-drilled with slotted holes for permanent attachment to foundation. Three point door latching mechanism. Designed for 50ºC (122º F) ambient temperature, white enclosure reduces solar heating. Input AC line circuit breaker with pad lockable flange mount external operator. State of the art operator control panel with graphical interface. Available with or without Variable Sinewave Generator (VSG) technology – pure sine wave output. Latest generation IGBTs (Insulated Gate Bipolar Transistors). Microprocessor based control circuitry with non-volatile memory for all drive parameters. Surface mount technology with protective coating on all printed circuit boards. Input line transient voltage suppression - line to line and line to ground voltage surge protection. Six pulse input rectification (standard) or optional multi-pulse rectification for reduced AC line harmonics. Fused control power transformer. Extended acceleration time - reduces electrical and mechanical stress on pump and motor. “S” curve soft start / soft stop capability. Power loss ride through capability.
Operator Panel Features: • • • • • • • • • • • • • • • • • • •
©
Intuitive operator friendly menu is easy to use. Large bright screen is easy to read in direct sunlight. Built in real time clock – provides time and date stamp for historical data and event logger. Operator control panel monitors both drive parameters and well parameters. Note: Wood Group ESP downhole sensor is required to monitor well parameters. Drive and well parameters are displayed in engineering units using plain language text. User programmable functions and operating modes. Set point PI control – closed loop – programmable in engineering units. Comprehensive run status screen shows critical drive and well data in a single location. Time stamped event and fault log - stores last 256 drive events including faults, starts, stops, operator changes, etc. Historical data log - periodically samples and stores the values of 20 different drive and well parameters. - All parameters are time (to the second) and date stamped with 35 days of data retained. Trending screen – graphically displays historical data for important drive and well parameters. Software embedded circular recording ammeter – high resolution display with 1 day or 7 day format. Drive Status Lights - Shows drive operating mode and are visible from a distance. Software embedded drive lock-out and auto-restart switches. Programmable restart capability. USB port for data retrieval and transfer of drive information to memory stick. - Save historical data, event log information, recording ammeter data, and drive configuration information. Built in Modbus communications port – easy interface to customer SCADA systems. Multiple Languages Password protection to prevent unauthorized changes.
Wood Group-ESP 2009
6
Protective Features: • • • • • • • • • • • • • • •
Input phase insensitive – sequencing of 3 phase input power is not necessary. DC bus reactor. Diagnostic fault indication. Loss of load detection. Serial communication loss detection. Short circuit protection. Ground fault protection. Loss of input phase protection. Over voltage and under voltage protection. Over current and under current protection. Current limiting DC bus fuse. Motor stall protection. Heat sink over temperature protection. Adjustable motor current limit. Critical frequency avoidance – three selectable frequencies with adjustable bandwidth.
Electrical Specifications: Rated Input Voltage: Efficiency: Power Factor: Output Voltage: Output Frequency:
480 Volt, 3 phase, 60 Hz (+ / - 10% of rated voltage and frequency). Consult factory for other input voltages and frequency ratings. 97% or greater at full load. .95 or greater – Constant over operating range – Not speed or load dependent 0 Volts to rated input voltage 0 Hertz to 120 Hertz.
Control Specifications: Control Method: Accel / Decel: Drive Overload: Current Limit:
Sine coded output with optional VSG (Variable Sinewave Generation) technology. 0 Seconds to 6,000 seconds. 110% of drive rating for 60 seconds (Variable Torque). Programmable current limit.
Control I/O: Digital Inputs: Digital Outputs: Analog Inputs:
Analog Outputs: Analog Reference: Logic Reference:
7 Programmable inputs - 24 VDC, 8 mA – Sinking or Sourcing Logic. 2 Programmable dry contacts rated 250 VAC / 30 VDC @ 1A. 1 Fault contact - Form C dry contact rated 250 VAC / 30 VDC @ 1A. 2 Programmable inputs (10 bit). Analog 1 = 0 to +10 VDC – 20 K Ohms Analog 2 = 0 to +10 VDC – 20 K Ohms or 4 to 20 mA – 250 Ohms 2 Programmable outputs (10 bit) each = 0 to +10 VDC – 2 mA. +15 VDC Source – 20 mA. +24 VDC Source – 8 mA.
Environmental Specifications: Ambient Service Temperature: Ambient Storage Temperature: Humidity: Altitude: Vibration: ©
Wood Group-ESP 2009
0°C to 50°C (32°F to 122°F) to -40°C (-40°F) with optional arctic package. -20°C to 60°C (-4°F to 140°F) 0 to 100% Up to 1000 Meters (3300 Feet) without de-rate. 9.81m/s2 (1 G) maximum at 10 to 20 Hz, 2.0 m/s2 (0.2 G) at 20 Hz to 50 Hz.
7
Various Installation Examples
ESP Installation
SPS Installation
ESP Installation
ESP Installation
©
Wood Group-ESP 2009
Offshore Installation
8
CATALOG NUMBER EXPLANATION D A B C E F G H to Z Drive Rated Rated Rated Enclosure Output Description Options Type Amps Volts Hertz Pulse Type Type Example V7 - 675A - 480V - 60HZ - 6P N3R - VSG AP Position
Position A B
©
Description Vector 7 Drive Output Amps
C D E
Input Voltage Input Frequency Input Type
F G H–Z
Enclosure Type Output Type Options
Wood Group-ESP 2009
Choices V7 180A, 304A, 414A, 515A, 675A, 910A, 1215A, 1366A, 1444A, 1821A, Other 480VAC, 380VAC, 400VAC, Other 60HZ, 50HZ 6P = 6 Pulse, 12P = 12 Pulse, 18P = 18 Pulse, Other N3R = Nema 3R, N1 = Nema 1, Other VSG = Sine Wave, No Entry = PWM See Options Table on Page 14
9
VECTOR VII RATINGS AND CATALOG NUMBERS Vector VII Drives – without VSG (5) - 480 VAC / 60 Hertz
Catalog Number V7-124A-480V-60HZ-6P-N3R V7-124A-480V-60HZ-12P-N3R (3) V7-124A-480V-60HZ-18P-N3R (3) V7-180A-480V-60HZ-6P-N3R V7-180A-480V-60HZ-12P-N3R (3) V7-180A-480V-60HZ-18P-N3R (3) V7-240A-480V-60HZ-6P-N3R V7-240A-480V-60HZ-12P-N3R (4) V7-240A-480V-60HZ-18P-N3R (4) V7-304A-480V-60HZ-6P-N3R V7-304A-480V-60HZ-12P-N3R (3) V7-304A-480V-60HZ-18P-N3R (3) V7-414A-480V-60HZ-6P-N3R V7-414A-480V-60HZ-12P-N3R (3) V7-414A-480V-60HZ-18P-N3R (3) V7-515A-480V-60HZ-6P-N3R V7-515A-480V-60HZ-12P-N3R (3) V7-515A-480V-60HZ-18P-N3R (3) V7-675A-480V-60HZ-6P-N3R V7-675A-480V-60HZ-12P-N3R (3) V7-675A-480V-60HZ-18P-N3R (3) V7-910A-480V-60HZ-6P-N3R V7-910A-480V-60HZ-12P-N3R (3) V7-910A-480V-60HZ-18P-N3R (3) V7-1215A-480V-60HZ-6P-N3R V7-1215A-480V-60HZ-12P-N3R (3) V7-1215A-480V-60HZ-18P-N3R (3) V7-1366A-480V-60HZ-6P-N3R V7-1366A-480V-60HZ-12P-N3R (3) V7-1366A-480V-60HZ-18P-N3R (3) V7-1444A-480V-60HZ-6P-N3R V7-1444A-480V-60HZ-12P-N3R (3) V7-1444A-480V-60HZ-18P-N3R (3) V7-1821A-480V-60HZ-6P-N3R V7-1821A-480V-60HZ-12P-N3R (3) V7-1821A-480V-60HZ-18P-N3R (3)
(1) (2) (3) (4) (5)
©
Output KVA (4) 104 104 104 150 150 150 200 200 200 253 253 253 344 344 344 428 428 428 561 561 561 757 757 757 1010 1010 1010 1136 1136 1136 1200 1200 1200 1514 1514 1514
Input Pulses 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18
Output Voltage 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
Output Amperes 124 124 124 180 180 180 240 240 240 304 304 304 414 414 414 515 515 515 675 675 675 910 910 910 1215 1215 1215 1366 1366 1366 1444 1444 1444 1821 1821 1821
Input Voltage 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
Input Amperes 136 136 (1) 136 (2) 198 198 (1) 198 (2) 264 264 (1) 264 (2) 334 334 (1) 334 (2) 456 456 (1) 456 (2) 567 567 (1) 567 (2) 743 743 (1) 743 (2) 1000 1000 (1) 1000 (2) 1340 1340 (1) 1340 (2) 1500 1500 (1) 1500 (2) 1590 1590 (1) 1590 (2) 2000 2000 (1) 2000 (2)
Total input amperes. Amperes per input phase are 50% of listed value. Total input amperes. Amperes per input phase are 33% of listed value. Multi-pulse drives require a Phase Shift Transformer. This is not included with the drive. Output KVA calculated at 480 VAC. VSG is required for ESP applications.
Wood Group-ESP 2009
10
VECTOR VII RATINGS AND CATALOG NUMBERS Vector VII Drives with VSG - 480 VAC / 60 Hertz
Catalog Number V7-124A-480V-60HZ-6P-N3R V7-124A-480V-60HZ-12P-N3R V7-124A-480V-60HZ-18P-N3R V7-180A-480V-60HZ-6P-N3R-VSG V7-180A-480V-60HZ-12P-N3R-VSG V7-180A-480V-60HZ-18P-N3R-VSG V7-240A-480V-60HZ-6P-N3R-VSG V7-240A-480V-60HZ-12P-N3R-VSG V7-240A-480V-60HZ-18P-N3R-VSG V7-304A-480V-60HZ-6P-N3R-VSG V7-304A-480V-60HZ-12P-N3R-VSG V7-304A-480V-60HZ-18P-N3R-VSG V7-414A-480V-60HZ-6P-N3R-VSG V7-414A-480V-60HZ-12P-N3R-VSG V7-414A-480V-60HZ-18P-N3R-VSG V7-515A-480V-60HZ-6P-N3R-VSG V7-515A-480V-60HZ-12P-N3R-VSG V7-515A-480V-60HZ-18P-N3R-VSG V7-675A-480V-60HZ-6P-N3R-VSG V7-675A-480V-60HZ-12P-N3R-VSG V7-675A-480V-60HZ-18P-N3R-VSG V7-910A-480V-60HZ-6P-N3R-VSG V7-910A-480V-60HZ-12P-N3R-VSG V7-910A-480V-60HZ-18P-N3R-VSG V7-1215A-480V-60HZ-6P-N3R-VSG V7-1215A-480V-60HZ-12P-N3R-VSG V7-1215A-480V-60HZ-18P-N3R-VSG V7-1366A-480V-60HZ-6P-N3R-VSG V7-1366A-480V-60HZ-12P-N3R-VSG V7-1366A-480V-18P-N3R-VSG V7-1444A-480V-60HZ-6P-N3R-VSG V7-1444A-480V-60HZ-12P-N3R-VSG V7-1444A-480V-60HZ-18P-N3R-VSG V7-1821A-480V-60HZ-6P-N3R-VSG V7-1821A-480V-60HZ-12P-N3R-VSG V7-1821A-480V-60HZ-18P-N3R-VSG
(1) (2) (3) (4) (5)
©
(3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3) (3)
Output KVA (4) 104 104 104 150 150 150 200 200 200 253 253 253 344 344 344 428 428 428 561 561 561 757 757 757 1010 1010 1010 1136 1136 1136 1200 1200 1200 1514 1514 1514
Input Pulses 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18
Output Voltage 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
Output Amperes 124 124 124 180 180 180 240 240 240 304 304 304 414 414 414 515 515 515 675 675 675 910 910 910 1215 1215 1215 1366 1366 1366 1444 1444 1444 1821 1821 1821
Input Voltage 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
Input Amperes 136 136 (1) 136 (2) 198 198 (1) 198 (2) 264 264 (1) 264 (2) 334 334 (1) 334 (2) 456 456 (1) 456 (2) 567 567 (1) 567 (2) 743 743 (1) 743 (2) 1000 1000 (1) 1000 (2) 1340 1340 (1) 1340 (2) 1500 1500 (1) 1500 (2) 1590 1590 (1) 1590 (2) 2000 2000 (1) 2000 (2)
Total input amperes. Amperes per input phase are 50% of listed value. Total input amperes. Amperes per input phase are 33% of listed value. Multi-pulse drives require a Phase Shift Transformer. This is not included with the drive. Output KVA calculated at 480 VAC. VSG is required for ESP applications.
Wood Group-ESP 2009
11
VECTOR VII RATINGS AND CATALOG NUMBERS Vector VII Drives –without VSG (5) - 380 VAC / 50 Hertz
Catalog Number V7-124A-480V-50HZ-6P-N3R V7-124A-480V-50HZ-12P-N3R (3) V7-124A-480V-50HZ-18P-N3R (3) V7-180A-380V-50HZ-6P-N3R V7-180A-380V-50HZ-12P-N3R (3) V7-180A-380V-50HZ-18P-N3R (3) V7-240A-380V-50HZ-6P-N3R V7-240A-380V-50HZ-12P-N3R (3) V7-240A-380V-50HZ-18P-N3R (3) V7-304A-380V-50HZ-6P-N3R V7-304A-380V-50HZ-12P-N3R (3) V7-304A-380V-50HZ-18P-N3R (3) V7-414A-380V-50HZ-6P-N3R V7-414A-380V-50HZ-12P-N3R (3) V7-414A-380V-50HZ-18P-N3R (3) V7-515A-380V-50HZ-6P-N3R V7-515A-380V-50HZ-12P-N3R (3) V7-515A-380V-50HZ-18P-N3R (3) V7-675A-380V-50HZ-6P-N3R V7-675A-380V-50HZ-12P-N3R (3) V7-675A-380V-50HZ-18P-N3R (3) V7-819A-380V-50HZ-6P-N3R V7-819A-380V-50HZ-12P-N3R (3) V7-819A-380V-50HZ-18P-N3R (3) V7-1093A-380V-50HZ-6P-N3R V7-1093A-380V-50HZ-12P-N3R (3) V7-1093A-380V-50HZ-18P-N3R (3) V7-1229A-380V-50HZ-6P-N3R V7-1229A-380V-50HZ-12P-N3R (3) V7-1229A-380V-50HZ-18P-N3R (3) V7-1300A-380V-50HZ-6P-N3R V7-1300A-380V-50HZ-12P-N3R (3) V7-1300A-380V-50HZ-18P-N3R (3) V7-1639A-380V-50HZ-6P-N3R V7-1639A-380V-50HZ-12P-N3R (3) V7-1639A-380V-50HZ-18P-N3R (3)
(1) (2) (3) (4) (5)
©
Output KVA (4) 82 82 82 118 118 118 158 158 158 200 200 200 272 272 272 338 338 338 444 444 444 539 539 539 719 719 719 809 809 809 856 856 856 1079 1079 1079
Input Pulses 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18 6 12 18
Output Voltage 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380
Output Amperes 124 124 124 180 180 180 240 240 240 304 304 304 414 414 414 515 515 515 675 675 675 819 819 819 1093 1093 1093 1229 1229 1229 1300 1300 1300 1639 1639 1639
Input Voltage 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380
Input Amperes 136 136 (1) 136 (2) 198 198 (1) 198 (2) 264 264 (1) 264 (2) 334 334 (1) 334 (2) 456 456 (1) 456 (2) 567 567 (1) 567 (2) 743 743 (1) 743 (2) 901 901 (1) 901 (2) 1202 1202 (1) 1202 (2) 1352 1352 (1) 1352 (2) 1430 1430 (1) 1430 (2) 1803 1803 (1) 1803 (2)
Total input amperes. Amperes per input phase are 50% of listed value. Total input amperes. Amperes per input phase are 33% of listed value. Multi-pulse drives require a Phase Shift Transformer. This is not included with the drive. Output KVA calculated at 380 VAC. VSG is required for ESP applications.
Wood Group-ESP 2009
12
VECTOR VII RATINGS AND CATALOG NUMBERS Vector VII Drives with VSG - 380 VAC / 50 Hertz Output Input Output Catalog Number KVA (4) Pulses Voltage V7-124A-480V-50HZ-6P-N3R 82 6 380 V7-124A-480V-50HZ-12P-N3R (3) 82 12 380 V7-124A-480V-50HZ-18P-N3R (3) 82 18 380 V7-180A-380V-50HZ-6P-N3R-VSG 118 6 380 118 380 V7-180A-380V-50HZ-12P-N3R-VSG (3) 12 118 380 V7-180A-380V-50HZ-18P-N3R-VSG (3) 18 380 V7-240A-380V-50HZ-6P-N3R-VSG 158 6 380 V7-240A-380V-50HZ-12P-N3R-VSG (3) 158 12 V7-240A-380V-50HZ-18P-N3R-VSG (3) 158 380 18 380 V7-304A-380V-50HZ-6P-N3R-VSG 200 6 380 V7-304A-380V-50HZ-12P-N3R-VSG (3) 200 12 380 V7-304A-380V-50HZ-18P-N3R-VSG (3) 200 18 380 V7-414A-380V-50HZ-6P-N3R-VSG 272 6 380 V7-414A-380V-50HZ-12P-N3R-VSG (3) 272 12 380 V7-414A-380V-150HZ-8P-N3R-VSG (3) 272 18 380 V7-515A-380V-50HZ-6P-N3R-VSG 338 6 380 V7-515A-380V-50HZ-12P-N3R-VSG (3) 338 12 380 V7-515A-380V-50HZ-18P-N3R-VSG (3) 338 18 380 V7-675A-380V-50HZ-6P-N3R-VSG 444 6 380 V7-675A-380V-50HZ-12P-N3R-VSG (3) 444 12 380 V7-675A-380V-50HZ-18P-N3R-VSG (4) 444 18 380 V7-819A-380V-50HZ-6P-N3R-VSG 539 6 380 V7-819A-380V-50HZ-12P-N3R-VSG (3) 539 12 380 V7-819A-380V-50HZ-18P-N3R-VSG (3) 539 18 380 V7-1093A-380V-50HZ-6P-N3R-VSG 719 6 380 V7-1093A-380V-50HZ-12P-N3R-VSG(3) 719 12 380 V7-1093A-380V-50HZ-18P-N3R-VSG(3) 719 18 380 V7-1229A-380V-50HZ-6P-N3R-VSG 809 6 380 V7-1229A-380V-50HZ-12P-N3R-VSG(3) 809 12 380 V7-1229A-380V-50HZ-18P-N3R-VSG(3) 809 18 380 V7-1300A-380V-50HZ-6P-N3R-VSG 856 6 380 V7-1300A-380V-50HZ-12P-N3R-VSG(3) 856 12 380 V7-1300A-380V-50HZ-18P-N3R-VSG(3) 856 18 380 V7-1639A-380V-50HZ-6P-N3R-VSG 1079 6 380 V7-1639A-380V-50HZ-12P-N3R-VSG(3) 1079 12 380 V7-1639A-380V-50HZ-18P-N3R-VSG(3) 1079 18
(1) (2) (3) (4) (5)
©
Output Amperes 124 124 124 180 180 180 240 240 240 304 304 304 414 414 414 515 515 515 675 675 675 819 819 819 1093 1093 1093 1229 1229 1229 1300 1300 1300 1639 1639 1639
Input Voltage 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380
Input Amperes 136 136 (1) 136 (2) 198 198 (1) 198 (2) 264 264 (1) 264 (2) 334 334 (1) 334 (2) 456 456 (1) 456 (2) 567 567 (1) 567 (2) 743 743 (1) 743 (2) 901 901 (1) 901 (2) 1202 1202 (1) 1202 (2) 1352 1352 (1) 1352 (2) 1430 1430 (1) 1430 (2) 1803 1803 (1) 1803 (2)
Total input amperes. Amperes per input phase are 50% of listed value. Total input amperes. Amperes per input phase are 33% of listed value. Multi-pulse drives require a Phase Shift Transformer. This is not included with the drive. Output KVA calculated at 380 VAC. VSG is required for ESP applications.
Wood Group-ESP 2009
13
OPTIONS TABLE Factory Installed options include: Code P12 SH
Name 12 Pulse Field Conversion Kit Space Heater
Ratings 150 561 All
AP
Arctic Package
All
DP
Desert Package
All
Analog Output Converter Digital Input Converter
All
AOC DIC TVSS PJB
TBX VCS RTU ES DSI COMM1 COMM2
Transient Voltage Surge Suppression Power Junction Box
Terminal Block With Oversized Terminals RTU for SPS Use E-Stop DownHole Sensor Interface Wireless Router Communications Satellite Interface
All All All
All ALL All All All All
ETI
Ethernet Interface
ALL
SST
Stainless Steel Construction Brass Gland Plate CE Certification UL Certification CUL Certification
All
BGP CE UL / CUL
ALL 105-561 105-561 NVSG
Consult Factory for other options.
©
Wood Group-ESP 2009
14
Description Allows conversion of 6 pulse drive to a 12 pulse drive in the field. Prevents condensation from forming inside the drive enclosure. Generally not suitable for enclosure heating in cold climates. Provides thermostatically controlled enclosure heaters and ventilation control for operation to -40°C (-40°F). Provides added protection to reduce solar heating in desert applications. Converts the two 0 to +/- 10V Analog Outputs on Vector VII to 4 to 20 ma outputs. Converts the seven 24 V DC Digital Inputs on Vector VII to 120 VAC Digital Inputs. Provides additional (very robust) protection against voltage transients and surges. For added convenience all drive power connections (3-phase drive input and motor output plus a ground connection) are wired to terminal blocks in a junction box mounted on the side of the drive enclosure. Provides Customer I/O Interface terminal block with larger than standard terminals. Provides Additional AI / AO and DI / DO Provides emergency stop of drive. Provides interface to SmartGuard® downhole sensor via drive Operator Control Panel. Provides remote user interface to drive via a wireless computer connection. Provides SCADA interface to the drive via satellite. Provides Interface from drive to Ethernet system. Provides corrosion resistance in adverse operating conditions such as offshore platforms. For Offshore / Marine Use Complies with European Union Certification Complies with Underwriters Laboratory Requirements for United States and Canada
MANUFACTURER QUALIFICATIONS Wood Group ESP has been a supplier of drives for many years. Our drives are installed in a variety of oilfield pumping applications, both onshore and offshore. These include Electric Submersible Pumps (ESP), Surface Pumping Systems (SPS), and Progressing Cavity Pump (PCP) applications. Wood Group ESP’s experience with a wide variety of different oilfield pumping applications has given us the unique ability to develop a specialized drive product for the markets we serve. Our drives include application specific software and a custom Operator Control Panel that provides a common, easy to use operator interface to both the drive’s parameters and the downhole or process sensors associated with the application. Wood Group ESP can provide stand alone drives for indoor or outdoor environments or we can provide complete skid mounted packages including transformers that are easy to install and transport. We can also provide a total drive solution that includes switchgear, transformers, and a modular E-House complete with environmental controls and fire suppression systems. MANUFACTURER CERTIFICATIONS Wood Group ESP is an ISO 9001 certified company. This ensures that all quality and corrective action procedures are documented and implemented to ensure the highest level of product quality. At Wood Group ESP our goal is complete customer satisfaction. GENERAL SPECIFICATIONS / OPERATING CONDITIONS / DESIGN FEATURES Input Power Requirements: The Wood Group ESP Vector VII drive is designed to accept three phase input power within a voltage range of 480 VAC, +/- 10%. Optionally the Vector VII drive can be configured to accept some other standard input voltage such as 380 VAC, +/- 10% or 400 VAC +/- 10%. The input frequency requirement of the Vector VII drive is either 50 Hz +/- 5% or 60 Hz +/- 5%. Consult factory for all voltage requirements other than 480 VAC / 60 Hz. The Vector VII drive has a 6 pulse input as standard and can also be supplied with an optional 12 pulse, or 18 pulse input rectifier for reduced Input AC line harmonics. These drive configurations will require a special input phase shifting transformer (consult factory for transformer requirements on all 12 pulse and 18 pulse applications). See harmonic mitigation section (page 30) for details on the benefits of multi-pulse drives. Electrical Noise Immunity: Noise immunity is in accordance with IEC61800-3.
©
Wood Group-ESP 2009
15
Output Power Characteristics: The Vector VII drive is designed to produce an adjustable voltage, adjustable frequency output to vary the speed of an AC induction motor. Output voltage is adjustable from 0 to 100% of the applied input voltage. Output frequency is adjustable from 0 hertz to 120 hertz. The inverter section produces a sine coded output waveform using proven IGBT technology. For applications requiring a sinewave output, optional Variable Sinewave Generator (VSG) technology is available. VSG technology minimizes the effects of reflected waves caused by long cable lengths. With VSG technology motors may be successfully operated using cable lengths up to 15,000 feet. Power Conditioning: An input isolation transformer is not required for protection from normal line transients. Overload Capability: Vector VII drives will produce 110% of rated output current for 1 minute. Efficiency: Vector VII drive efficiency is 97% or higher at full load and full speed. Enclosure Features: • • • • • •
NEMA 3R outdoor rated. 10 gauge welded steel construction. Multi-stage paint process including iron phosphate wash for adhesion and white epoxy top coat. Lifting eyes. Lockable door handle and flange mount external circuit breaker disconnect handle. Door mounted Operator Control Panel - all drive adjustments can be made with the enclosure door closed.
Hardware: The Vector VII employs the following power components: • • • • • • • •
©
Diode Input – 6 Pulse, 12 Pulse, and 18 Pulse configurations available. Inverter Section with the latest generation IGBT power devices DC bus inductor included on all ratings. Phase to phase and phase to ground MOV protection. Plug-in connections on printed circuit boards. Microprocessor based inverter logic isolated from power circuits. Operator Control Panel is common for all KVA ratings. Interface includes a large LCD graphical display with programming keys. Common control connections for all ratings.
Wood Group-ESP 2009
16
Control Logic: The drive is programmable or self adjusting for operation under the following conditions: • • • •
Operate drive with motor disconnected. Controlled shut down, with no component failure in the event of an output phase to phase or phase to ground short circuit and annunciation of the fault condition. Multiple programmable stop modes including - Ramp, Coast, Ramp-to-Hold, and S-curve. Multiple acceleration and deceleration rates.
Terminal Blocks: Separate terminal blocks are provided for control and power wiring. Optional power junction boxes offer additional installation convenience. Control Inputs and Outputs: Digital Inputs: Digital Outputs: Analog Inputs:
Analog Outputs: Analog Reference: Logic Reference:
7 programmable inputs - 24 VDC, 8 ma – sinking or sourcing logic 2 programmable dry contacts rated 250 VAC / 30 VDC @ 1A 1 fault contact - form C dry contact rated 250 VAC / 30 VDC @ 1A 2 programmable Inputs (10 bits) Analog 1 = 0 to +10 VDC – 20 K ohms Analog 2 = 0 to +10 VDC – 20 K ohms or 4 to 20 mA – 250 ohms 2 programmable outputs (10 bits) each = 0 to +10 VDC – 2 mA +15 VDC source – 20 mA +24 VDC source – 8 mA
Customer Interface: Digital & Analog I/O
©
Wood Group-ESP 2009
17
Reference Signals: The Vector VII drive is usually configured to be controlled locally using the door mounted Operator Control Panel. Reference signals can also come from a remote controller when the Vector VII drive is connected to an external SCADA system. Vector VII can also be configured to follow other reference signals including analog input signals as listed below. 1. Remote potentiometer 2. 0-10 VDC 3. 4-20 ma Loss of Reference: The Vector VII drive can be configured to compensate for loss of its external frequency command. This command is considered lost if the drive reference drops to 10% of its value in 400 ms or less. Drive loss of reference can be programmed from 0 to 100% of drive’s speed command setting. Factory default setting is 80% of speed command. Power Loss Ride Through Capability: The Vector VII drive is capable of riding through a momentary loss of input power without shutting down. Automatic Restart: The Vector VII drive can be programmed to automatically restart after a drive fault. The number of restart attempts can be programmed from 0 to 10 with a factory default setting of zero. Time between restart attempts is programmable from .5 to 600 seconds with a factory de-fault setting of 180 seconds. Jump Frequencies: Three adjustable set points that lock out continuous operation at frequencies which may produce mechanical resonance are provided. Bandwidth is selectable from 0 to 20 hertz. Current Limit Programmable current limit is from 0% to 180% of drive rated output current. Acceleration / Deceleration Accel / Decel settings provide separate adjustments to allow either setting to be adjusted from 0.0 seconds to 6000.0 seconds. Minimum Frequency Limit / Fault The minimum frequency limit is set as a percentage of the command / set point frequency and may be used with PI control. If the drive senses this limit or drops below it a fault occurs and the drive will shut down. ©
Wood Group-ESP 2009
18
Bus Regulation DC Bus regulation is available to reduce the possibility of drive over-voltage trips due to regenerative conditions. Bus voltage is monitored and an internal regulator adjusts the drive’s output frequency to maintain bus voltage at a nominal (100%) level. Undervoltage trip occurs at 380 VDC and overvoltage trip occurs at 800 VDC. Underload Detection Enabled or disabled via programming, this feature allows the user to select the output current level that indicates the load has been lost. A programmable timing delay can also be set. Maximum time is 10 seconds. Factory default is “Disabled” and factory default time is 10 seconds. Motor Overload Protection Electronic motor overload protection is provided from both a current overload and motor overheating function. Exceeding either limit results in a trip / fault condition that will de-energize the drive. Trip time is user selectable. Fault Memory / Event Log Faults can be accessed via the event log screen. The event log contains the most current 256 events with each being time stamped with the month, day, year, hour and minute of occurrence. Any parameter changes will contain previous and current settings for user reference. Data is stored in a non-volatile memory. Adjustments The Operator Control Panel is used for all set-up, operation and adjustment settings. All adjustments are stored in a nonvolatile memory. No potentiometer adjustments are used. Communications Interface Operator Control Panel has multiple user selectable communication port assignments for See Options list on page 12 for other communication protocols that can be used with the drive. Hard Start This function allows the operator to initiate a continuous forward / reverse start of downhole equipment. Function is designed for assistance in starting equipment that is difficult to start because of “sanded in” conditions or similar circumstances. Parameters are user configurable.
©
Wood Group-ESP 2009
19
OPERATOR CONTROL PANEL Interface to the Vector VII drive is provided via an Operator Control Panel with integral display. The display is easily read in bright sunlight and has a backlit LCD. It shows drive operating conditions, fault indications and programming information. The Operator Control Panel is standard on all drive ratings, has password protection, and provides a monitoring interface to the optional SmartGuard® downhole sensor. Data can be retrieved from the drive using a laptop computer or memory stick via the USB port directly below the Operator Control Panel. Some of its features are as follows: • • • • • • • • • • • • •
Intuitive Menu Select Screen. (See Figure 1) Comprehensive Run Status Screen. (See Figure 2) Operator Control Panel displays actual date and time. (See Figure 2) Drive and well parameters are displayed in plain text. (See Figure 2) All Monitors Screen gives snapshot of drive and downhole sensor status. (See Figure 3) Software Embedded Recording Ammeter with 1 or 7 day format. (See Figure 4) Trending Screen for various surface and downhole parameters. (See Figure 5) Software Embedded Lock Out Switches. (See Figure 6) Time Stamped Event Log (256 events). (See Figure 7) SmartGuard downhole sensor screen. (See Figure 8) History Logs (35 days of data). (See Figure 9) Drive status lights showing the drive operating mode (See Figure 10) Multiple Languages
A representation of the Operator Control Panel is shown below along with an explanation of the function keys.
Operator Control Panel and USB Port ©
Wood Group-ESP 2009
Function Key Explanations
20
Operator Control Panel Screen Examples:
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
©
Wood Group-ESP 2009
Figure 6
21
Operator Control Panel Screen Examples:
Figure 7
Figure 8
History Screen This screen displays logged performance data using 20 different parameters. They are as follows.
Figure 9
Drive Outputs Volts Amps Hertz Analog 1 Analog 2 Digital Input
©
Wood Group-ESP 2009
DC Bus Volts Heat Sink Temp. KW PI Control Output Status
SmartGuard Outputs Intake PSI Discharge PSI Intake Temp. Motor Temp.
22
Vibration Leakage Current UpHole DC Volts
Transformer Outputs To Motor Volts Amps
Operator Control Panel Screen Examples: Status Indicator Lights The drive will display drive status information that can be seen from a distance. Drive status indicators are as follows: • • • • •
Green = Drive running. Red = Drive stopped in ready state Flashing Red = Drive stopped in fault state Amber = Drive stopped in restart state. Drive will automatically restart – but the time to restart is greater than 1 minute. Flashing Amber = Drive stopped in restart or standby state. Drive will automatically restart in less than 1 minute. If in standby state, the drive will restart immediately whenever the standby switch closes. Figure 10
Start up of the Vector VII drive can be easily accomplished using basic setup parameters such as minimum and maximum frequency, acceleration and deceleration times, motor data, overload and underload limits, and other parameters. An example screen is shown below. Frequency Setup
Figure 11
©
Wood Group-ESP 2009
23
Operator Control Panel Screen Examples: Alarms Setup The Alarms Setup screen allows a logged on user to set the overload and underload limits as well as other alarm parameters. See figures 12 and 13 below.
Figure 12
Figure 13
The Vector VII drive is capable of operating as a frequency control, a current control, a pressure control, or it can be set to follow an Analog Signal from an external source. The following screens show how to configure the Vector VII drive for Frequency Control or Analog Signal Follower control. Operating / Control Mode (Frequency and Analog Follower)
Figure 14
©
Wood Group-ESP 2009
Figure 15
24
Operator Control Panel Screen Examples: Operating / Control Mode (Pressure) An example of the pressure control mode using the internal process PI regulator is shown in Figures 16 and 17. In this example if the pressure measured at the pump discharge falls below the set point, the drive will speed up and try to restore the pressure (up to the maximum frequency defined on the Frequency Setup screen – Figure 17). If the pressure exceeds the set point, the drive will slow to reduce the pressure (down to the minimum frequency defined on the Frequency Setup screen). The drive will adjust the frequency in the opposite direction if the intake pressure is used as a reference. Protection is provided for a loss of feedback or reference signal. Process control can be enabled or disabled with a hardwire input.
Figure 16
Figure 17
Current Control Mode This allows the drive to operate with a constant current reference point and would primarily be used for gassy wells.
Figure 18 ©
Wood Group-ESP 2009
25
Operator Control Panel Screen Examples: Drive I/O Setup The user can easily determine the state of I/O settings at a glance by using this screen. S1 through S7 are user digital inputs, M1-M2 along with M3-M4 are digital outputs, A1 and A2 are analog inputs.
Figure 19
Communications (Comm) Setup A logged on user can define SCADA Modbus address and assign how the communication ports may be used. Comm port 2 is the default setting for external SCADA system communications.
Figure 20
©
Wood Group-ESP 2009
26
Operator Control Panel Screen Examples: Miscellaneous Setup This screen allows a logged on user to configure various parameters. For example, enable or disable downhole sensor communications (SmartGuard), set output transformer winding ratio to allow calculation of downhole motor voltage and current, or external fault settings status selection.
Figure 21 Maintenance Screen Logged on user can perform various functions such as checking or updating all drive parameters, resetting prior parameter settings to factory defaults, upgrading firmware, or downloading various logs and the internal digital recording ammeter data to a memory stick. Additionally, if several drives will have the same operating parameters these settings from the first drive can be downloaded to a memory stick and uploaded to the other drives via the USB port. This facilitates getting all drives running.
Figure 22 ©
Wood Group-ESP 2009
27
Operator Control Panel Screen Examples: Last Fault Screen User / operator can easily view current drive condition and when last fault occurred.
Figure 23 Hard Start Screen User selectable for situations where pump may be “sanded in” and hard to start. This allows submersible equipment to oscillate at pre-determined intervals and ramp up to set point speed after equipment becomes free.
Figure 24
©
Wood Group-ESP 2009
28
Surface Pumping Systems (SPS™) Vector® VII drives have the capability of communicating serially with the VCS® RTU. This allows for expanded I/O and use of existing VCS® RTU SPS software / automation routines for control in surface pumping applications. Drive Frequency is controlled by the fully programmable internal PID loop of the RTU. Dedicated I/O points commonly used with SPS applications and other fully programmable I/O points reside on the RTU. It is recommended that this RTU option be used to control startup sequencing. Twelve digital I/O (120 VAC standard, 24 VDC optional) and 10 analog I/O (8 analog inputs (4-20 ma standard, 0-10 VDC optional) and 2 analog outputs (0-10 VDC) are available. These are in addition to the 9 digital I/O and 4 analog I/O on the Vector VII drive (see page 7). The following flow chart illustrates a typical SPS system start up sequence. Also shown is the VCS RTU and typical SPS skid system.
©
Wood Group-ESP 2009
29
INPUT HARMONIC MITIGATION Excessive AC Line Harmonics can cause problems in the AC power system including the overheating of power system components such as transformers, circuit breakers, and panel boards. It can also cause nuisance tripping of circuit breakers, and the inadvertent transfer of electrical noise to critical loads such as communications systems, computers, and process control equipment. Drives are a potential source of AC line harmonics and control of those harmonics reflected back to the power distribution system may be an important consideration in the selection of a drive. Multi-pulse drives can help you maintain Vector VII drives may be ordered with 6 Pulse (standard), 12 Pulse, and 18 Pulse input rectifier assemblies. The 6 pulse input rectifier assembly is generally accepted as the industry standard for low voltage AC drives. It is very simple, relatively inexpensive, and requires no additional (phase shifting) transformer for proper operation. When the control of Input AC line harmonics is important, 12 Pulse and 18 Pulse input rectifier assemblies are often selected. These drive configurations (12 Pulse and 18 Pulse) are sometimes referred to as “multi-pulse” drives. The input rectifier assembly for 12 pulse and 18 pulse drives is more complex than the input rectifier assembly for a 6 pulse drive – in fact, a 12 pulse input rectifier assembly consists of two 6 pulse rectifier bridges operating in parallel and an 18 pulse input rectifier assembly consists of three 6 pulse rectifier bridges operating in parallel. The added cost of these input rectifier assemblies is generally not that significant in the overall cost of the drive. The major cost differential (and it can be quite significant) between a 6 pulse drive and a 12 pulse or 18 pulse drive is the added cost of the Phase Shift Transformer that is required for “multi-pulse” operation. The multi-pulse phase shift transformers have conventional three phase inputs. The output of a 12 pulse phase shift transformer is a six wire connection and the output of an 18 pulse phase shift transformer is a nine wire connection. Twelve and Eighteen Pulse drives introduce lower levels of AC line harmonics into the power system than conventional Six Pulse Drives. Typical measurements for these various different front end configurations are shown below. These values should be used for estimating purposes only as measured results can vary based on line impedance, other linear loads on the feeder transformer, pre-existing harmonics due to other non-linear loads on the supply, and other factors. In general 12 pulse drives provide substantial reduction in power line harmonics over 6 pulse units and 18 pulse drives provide IEEE-519 compliance.
©
Category
6-Pulse Drive
12-Pulse Drive
18-Pulse Drive
Current THD
30-35%
6.5-9.5%
4.5-5%
Power Factor
.92-.95
.97-.98
.98-.99
DPF
.95-.97
.96-.98
.98-.99
K-Factor
3.0-5.0
2.0-3.0
1.0-2.0
Wood Group-ESP 2009
30
Multi-Pulse Examples:
12 Pulse Drive – Basic Schematic
18 Pulse Drive – Basic Schematic
©
Wood Group-ESP 2009
31
OUTPUT HARMONIC MITIGATION Wood Group-ESP developed VSG (Variable Sinewave Generator) technology specifically for Electric Submersible Equipment. It is a proprietary solution that provides a virtually pure sinewave output to downhole equipment and elimination of reflected wave phenomenon (motor spiking). Motor spiking can quickly destroy motor insulation and cause equipment failure. By virtue of VSG performance characteristics submersible motor heating caused by output harmonics is dramatically reduced. Typically the industry “rule of thumb” is that for every 10º C heat increase over the motor design point insulation life of the equipment decreases by 50%. Harmonics generate additional heat and mitigation of them can contribute to increased equipment life and in some cases lower operating expenses. VSG technology is effective with cable lengths up to 15,000 feet.
Failed motor winding – Motor Spiking
Vector VII with VSG – Virtually Pure Sinewave Output
©
Wood Group-ESP 2009
32
Grounding and Bonding Correct system grounding and equipment bonding is required to ensure proper operation of equipment during both normal operation and underfault conditions. Grounding and bonding conductors provide a path to ground for lethal fault currents and voltages. Failure to correctly ground and bond equipment can lead to equipment damage and personnel injury or death. Grounding applies to the main service connection to ground. Service transformer wye-point and enclosures, including the service disconnect switch, must be connected to a common ground conductor and grounding electrodes (Refer to local electrical authority for approved grounding electrodes and methods in your area). System ground resistance should not exceed 25 Ohms to ground and ideally be between 1-5 Ohms to ground. Ground resistance checks should only be made by qualified electrical inspection agencies. Bonding applies to all other electrical equipment and raceways. A bonding conductor must be connected from the main grounding electrodes to all enclosures, junction boxes, buildings, electrical pipes, and the wellhead. This equipment provides an internal ground connection for the bonding conductor. This connector is connected to the internal ground bus of the enclosure. A typical 3/60/480 VAC ESP installation is shown below.
©
Wood Group-ESP 2009
33
GENERATOR REQUIREMENTS Generators are often used as a source of power for oil field applications. When drives are operated from a generator, specific operational problems can occur unless the overall power system is properly designed for the application. Generators almost always have a higher source impedance than that of a typical electrical utility. Therefore, the non-linear current drawn by a drive tends to distort the generator output voltage waveform more than it would distort the voltage waveform of the electric utility. This distortion or “flat topping” of the generator output voltage waveform can confuse the generator’s voltage regulator and lead to a loss of voltage control and wide swings in generator output voltage. Because of this, the control of AC line harmonics is very important in generator applications. Whenever possible avoid situations where a generator is required to feed a load that consists mostly of non-linear loads (such as drives). It is best if the percentage of non-linear load can be kept to less than 20% of the total load connected to the generator. Often this is not possible. When a generator is used in a remote location as a power provider for a single drive or a group of drives, the percentage of non-linear load connected to the generator may approach 100%. In these situations, the following guidelines should be followed: 1. Use a multi-pulse drive (12 pulse or 18 pulse) to significantly reduce the AC line harmonics – this is usually your best approach. 2. Oversize the alternator component of the generator to lower the relative source impedance of the generator – doubling the size of the alternator will reduce the relative source impedance by 50%. While this may be helpful in applications where the percentage of non-linear load is less than 50% of the total connected load it will probably have little or no effect in applications where non-linear loads constitute a high percentage of the connected load. 3. Do not rely on the addition of AC line reactors between the generator and the drive to fix the problem – they simply add line impedance which often makes the problem worse. 4. Be very careful when applying harmonic filters to a generator system – passive harmonic filters generally consist of reactors and capacitors. The reactors add line impedance which usually does not solve your problem and the capacitors can cause the power factor to become leading under lightly loaded conditions. In general, generators do not like a leading power factor load – it confuses the generator’s voltage regulator and leads to a loss of voltage control and wide swings in generator output voltage. When Vector VII drives will be operated from a generator source it is best to contact Wood Group ESP with the following information: 1. Generator information – Manufacturer, Model #, Output Voltage, Kw, KVA, and Impedance. 2. Load Information – This information should be in the form of a power one line diagram with complete information about all connected loads - linear and non-linear. It should also include information about any line reactors, transformers, harmonic filters, and power factor correction equipment included on the system.
©
Wood Group-ESP 2009
34
Generator supplied power systems have the same requirements for grounding and bonding as utility supplied systems. Grounding electrodes must be installed and a common bonding conductor must be connected to all equipment and buildings. When the generator system does not incorporate a wye-point for connection to the system ground, then an isolation transformer is required between the generator and input to the VSD. This provides protection from floating voltages, and provides a wye-point for connection to the ground system. Non compliance with the above guidelines will result in poor performance and / or equipment failure. A typical 3/60/480 VAC generator ESP installation is shown below.
Vented Junction Box Detail See Application Brief 01010 and Drawing 146261 for additional references.
©
Wood Group-ESP 2009
35
DIMENSIONS & WEIGHTS - VECTOR VII WITHOUT VSG REFERENCE ONLY
“A” and “B” Frames
FRAME
A
B
C
D
KVA 150 200 253 344 428 561 750 850 1000 1200 1400 1500
HEIGHT (INCHES / MM) H
“C” and “D” Frames
WIDTH (INCHES / MM) W W1
DEPTH (INCHES / MM) D D1
82 / 2083
48 / 1220
36 / 915
42 / 1067
36 / 915
88 / 2236
57 / 1448
48 / 1220
40 / 1016
36 / 915
88 / 2236
99 / 2515
72 / 1829
53 / 1347
48 / 1220
4723 / 2143
88 / 2236
117 / 2972
90 / 2286
53 / 1347
48 / 1220
4800 / 2178
Note: VSG is required for all ESP applications.
©
Wood Group-ESP 2009
36
WEIGHT (POUNDS / KG) 944 / 429 1025 / 465 1100 / 499 1281 / 582 1325 / 601 1600 / 726
DIMENSIONS & WEIGHTS - VECTOR VII WITH VSG REFERENCE ONLY
“A” and “B” Frames
FRAME
A
B
C
D
KVA 150 200 253 344 428 561 750 850 1000 1200 1400 1500
HEIGHT (INCHES / MM) H
“C” and “D” Frames
WIDTH (INCHES / MM) W W1
Wood Group-ESP 2009
WEIGHT (POUNDS / KG) 1320 / 599 1400 / 635 1470 / 667 1781 / 808 1825 / 828 2100 / 953
82 / 2083
48 / 1220
36 / 915
42 / 1067
36 / 915
103 / 2616
57 / 1448
48 / 1220
40 / 1016
36 / 915
103 / 2616
99 / 2515
72 / 1829
53 / 1347
48 / 1220
5623 / 2551
103 / 2616
117 / 2972
90 / 2286
53 / 1347
48 / 1220
6000 / 2722
Note: VSG is required for all ESP applications.
©
DEPTH (INCHES / MM) D D1
37
CORPORATE OFFICE & MANUFACTURING
OUTSIDE U.S. SALES & SERVICE
WORLDWIDE SALES & OPERATIONS CANADA
5500 S.E. 59th St (73135) P.O. Box 15070 (73155) Oklahoma City, OKlahoma, USA Tel 405-670-1431 Toll free 800-723-3771 Fax 405-670-5463
19416 Park Row, Suite 100 Houston, Texas 77084 USA Tel 281-492-5100 Fax 281-492-8107
U.S. SALES & SERVICE GULF COAST
Brooks, Alberta Tel: 403-501-5822 Fax: 403-501-5823
Tunisia, Africa Tel: +216-7169-2281 Fax: +216-7169-2281
Calgary, Alberta Tel: 403-263-7166 Fax: 403-263-7211
Aberdeen, Scotland Tel: +44-1224-85-1000 Fax: +44-1224-85-1474
Leduc, Alberta * Tel: 780-955-2165 Toll free: 888-586-8909 Fax: 780-955-9487
LATIN AMERICA
Houston, Texas Tel: 281-492-5100 Fax: 281-492-8107
Andrews, Texas Tel: 432-523-9701 Fax: 432-523-9700
Laurel, Mississippi Tel: 601-649-2030 Toll free: 800-488-9260 Fax: 601-649-8819
Midland, Texas * Tel: 432-699-7401 Toll free: 800-749-7402 Fax: 432-699-4159
ASIA / PACIFIC Tanggu, China Tel: +86-22-6691-4650
Chubut, Argentina * Tel: +54-297-446-8254 Fax: +54-297-446-8377
MID CONTINENT
Snyder, Texas Tel: 325-573-9325 Fax: 325-573-1616
Jakarta, Indonesia Tel: +62-21-8370-2455 Fax: +62-21-831-2456
Bogota, Colombia Tel: +57-1-621-2425 Fax: +57-1-621-2264
ROCKY MOUNTAIN / PACIFIC
Singapore Tel: +65-6396-3626 Fax: +65-6396-5362
Quito, Ecuador Tel: 593-2-2428-211 Fax: 593-2-2428-213
Bangkok, Thailand Tel: +66-2722-2389 Fax: +66-2722-0775
El Tigre, Venezuela Tel: +58-283-241-7151 Fax: +58-283-241-8613
RUSSIA / CIS
Maracaibo, Venezuela * Tel: +58-261-200-9200 Fax: +58-261-7-361993
Oklahoma, City, Oklahoma* Tel: 405-671-1431 Toll free: 800-723-3771 Fax: 405-673-5463
Denver, Colorado Tel: 303-350-2111 Toll free: 800-535-0310 Fax: 303-350-2112
Purcell, Oklahoma Tel: 405-527-1566 Toll free: 800-256-5058 Fax: 405-527-7161
Baker, Montana Toll free: 800-535-0306 Fax: 307-234-4497
PERMIAN BASIN Artesia, New Mexico Tel: 505-746-4614 Fax: 505-746-4519
Buenos Aires, Argentina Tel: +54-4812-2329 Fax: +54-4812-2073
Moscow, Russia Tel: +7-495-937-6641 Fax: +7-495-937-6642
Casper, Wyoming * Tel: 307-234-4495 Toll free: 800-535-0306 Fax: 307-234-4497
Hobbs, New Mexico Tel: 505-392-7999 Fax: 505-392-8190
MIDDLE EAST
Nizhnevartovsk, Russia * Tel: +7-3466-416-195 Fax: +7-3466-416-295
Al Shark, Kuwait Tel: 965-398-3639-2810 Fax: 965-398-3639-2811
EUROPE / AFRICA
Shati Al Qurum, Oman Tel: 968-605501 Fax: 968-605784
Chad, Africa Tel: +235-626-3279 Fax: +235-41723
Dubai, UAE * Tel: +971-4-883-7595 Fax: +971-4-883-7579
Libya, North Africa Tel: +218-21-582-218-21-4842093 *Manufacturing Facility in addition to Sales & Service.
Woo d Group ESP World-Wide Operations
Business Regions
North America
South America
Central America Guatemala
Moscow Nizhnevartovsk
UK Asia Pacific Africa Nigeria Egypt Algeria Chad Libya
Middle East
South America Venezuela Colombia Argentina Brazil Ecuador
08-15-2009 ©
Wood Group-ESP 2009
Europe, Middle East, Africa
Russia
North America Canada Calgary Nisku Brooks U.S.A. Casper, WY Denver, CO Midland, TX Hobbs, NM Purcell, OK OKC, OK
EMA
38
Saudi Arabia Oman UAE Yemen
Singapore Indonesia Australia Vietnam Thailand China Japan
Wood Group ESP, Inc.
TRANSFORMERS VARIABLE SPEED DRIVE TRANSFORMER – 3 PHASE DIMENSIONS SIZE PRIMARY SECONDARY HXDXW KVA VOLTS VOLTAGE RANGE Inches CM 480-960 DELTA 67 480 47 x 35 x 41 119 x 89 x 104 831-1663 WYE 750-1258 DELTA 100 480 54 x 37 x 41 137 x 90 x 104 1300-2160 WYE 750 – 1497 DELTA 142 x 117 x 130 480 56 x 46 x 44 1299 – 2600 WYE 112 750 – 1550 DELTA 130 480 50.5 x 37 x 42 128 x 94 x 107 1299 – 2685 WYE 800-1559 DELTA 173 x 117 x 150 480 68 x 46 x 44 1386 - 2700 WYE 112 1100 – 2200 DELTA 135 x 109.x 200 480 53 X 43 X 51.5 1905 – 3811 WYE 131 1100 – 2200 DELTA 152 x 122 x 210 480 60 x 48 x 50 1905 – 3810 WYE 127 950-1900 DELTA 198 x 132 x 250 415 78 x 52 x 48 1650-3300 WYE 122 1100-2200 DELTA 198 x 132 x 250 480 78 x 52 x 48 1905-3810 WYE 122 1100 – 2200 DELTA 152 x 132 x 260 480 60 X 52 X 48 1905 – 3811 WYE 122 1100 – 2200 DELTA 188 x 137 x 350 480 74 x 54 x 50 1905 – 3811 WYE 127 1100 – 2200 DELTA 57.5 X 45 X 146 x 114 x 355 480 1905 – 3811 WYE 53.5 136 950-1900 DELTA 155 x 155 x 400 415 61 x 61 x 54 1650-3300 WYE 137 1109-2166 DELTA 191 x 155 x 400 480 75 x 61 x 54 1921-3732 WYE 137 1100 – 2200 DELTA 178 x 107 x 400 480 70 X 42 X 62 1905 – 3811 WYE 158 1100-2200 DELTA 198 x 117 x 450 480 78 x 46 x 58 1905-3810 WYE 147 198 x 165 x 1100 – 2200 DELTA 78 x 65 x 54 520 480 1905 – 3811 WYE 137 1300-2601 DELTA 208 x 170 x 750 480 82 x 67 x 60 2252-4505 WYE 152 1320-2640 DELTA 206 x 170 x 750 480 81 x 67 x 62 2286-4572 WYE 157 1400-2800 DELTA 208 x 173 x 850 480 82 x 68 x 62 2424-4850 WYE 157 1400-2800 DELTA 218 x 170 x 1000 480 86 x 67 x 64 2424-4850 WYE 163 Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
WEIGHT
PART NUMBER
Lbs.
Kgs.
2390
1084
136829
2530
1148
136828
2850
1293
136827
2850
1293
1057390
3740
1696
136683
3530
1601
1057017
3850
1746
136826
4220
1914
127729
4220
1914
136682
4220
1914
136825
6540
2967
136824
5350
2427
1054386
6675
3028
127961
6675
3028
136823
4500
2041
1057416
8175
3708
136681
8300
3765
136822
9326
4230
136680
9800
4445
136821
11200 5080
136820
11500 5216
136819
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc.
TRANSFORMERS SPECIALTY TRANSFORMER – 3 PHASE SIZE PRIMARY SECONDARY KVA VOLTS VOLTAGE RANGE 125
6000
150
13800
150
34500
250
13800
250
34500
450
13800
450
34500
500
13800
750
13800
750
34500
1100-2200 DELTA 1905-3810 WYE 800-1559 DELTA 1386-2700 WYE 800-1559 DELTA 1386–2700 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 1905-3811 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE
Wood Group ESP, Inc. Page-2
DIMENSIONS HXDXW Inches CM 142 x 114 x 56 x 45 x 46 117 198 x 117 x 78 x 46 x 44 112 198 x 117 x 78 x 46 x 44 112 178 x 132 x 70 x 52 x 48 122 198 x 132 x 78 x 52 x 50 127 224 x 165 x 88 x 65 x 54 137 244 x 165 x 96 x 65 x 54 137 193 x 203 x 76 x 80 x 55 140 229 x 170 x 90 x 67 x 60 152 229 x 170 x 90 x 67 x 60 152
The ESP Specialists
WEIGHT
PART NUMBER
Lbs.
Kgs.
3275
1486 136253
3927
1781 136615
3927
1781 136614
4431
2010 136675
4642
2106 136674
8450
3833 136677
8650
3924 136676
6502
2949 136198
9792
4442 136679
10307 4675 136678
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
37.5
480/831 Y
37.5
2400/4160 Y
37.5
7200/12470 Y
37.5
12470 ∆*
37.5
14400/24940 Y
37.5
19920/34500 grd Y
50
480/831 Y
50
2400/4160 Y
50
7200/12470 Y
50
12470 ∆*
50
14400/24940 Y
50
19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
75
480/831 Y
75
2400/4160 Y
75
7200/12470 Y
75
12470 ∆*
75
14400/24940 Y
75
19920/34500 grd Y
100
480/831 Y
100
2400/4160 Y
100
7200/12470 Y
100
12470 ∆*
100
14400/24940 Y
100
19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
54 x 28 x 30
137 x 71 x 76
945
429
54 x 28 x 30
137 x 71 x 76
945
429
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
54 x 33 x 30
137 x 84 x 76
1035
469
54 x 33 x 30
137 x 84 x 76
1035
469
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
167
2400/4160 Y
167
7200/12470 Y
167
12470 ∆
167
14400/24940 Y
167
19920/34500 Y
200
7200/12470 Y
200
12470 ∆
200
14400/24940 Y
200
19920/34500 Y
SECONDARY VOLTAGE RANGE 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
54 x 33 x 34
137 x 84 x 86
1645
746
54 x 33 x 34
137 x 84 x 86
1645
746
54 x 33 x 34
137 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1645
746
54 x 42 x 34
137 x 107 x 86
1700
771
54 x 42 x 34
137 x 107 x 86
1700
771
58 x 42 x 34
147 x 107 x 86
1700
771
58 x 42 x 34
147 x 107 x 86
1700
771
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc.
TRANSFORMERS SINGLE PHASE FACT 225 KVA **
PRIMARY VOLTS
37.5
2400/4160 Y 7200/12470 Y
37.5
7200/12470 Y 14400/24940 Y
37.5
14400/24940 Y 19920/34500 grd Y
50
2400/4160 Y 7200/12470 Y
50
7200/12470 Y 14400/24940 Y
50
14400/24940 Y 19920/34500 grd Y
75
2400/4160 Y 7200/12470 Y
75
7200/12470 Y 14400/24940 Y
75
14400/24940 Y 19920/34500 grd Y
100
2400/4160 Y 7200/12470 Y
100
7200/12470 Y 14400/24940 Y
100
14400/24940 Y 19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
45 x 23 x 26
114 x 58 x 66
605
274
50 x 23 x 26
127 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
49 x 23 x 26
124 x 58 x 66
710
322
54 x 23 x 26
137 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
49 x 28 x 30
124 x 71 x 76
890
404
54 x 28 x 30
137 x 71 x 76
945
428
54 x 28 x 30
137 x 71 x 76
945
428
49 x 33 x 30
124 x 84 x 76
975
442
54 x 33 x 30
137 x 84 x 76
1035
469
54 x 33 x 30
137 x 84 x 76
1035
469
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc. Page-6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 225 KVA **
PRIMARY VOLTS
167
2400/4160 Y 7200/12470 Y
167
7200/12470 Y 14400/24940 Y
167
14400/24940 Y 19920/34500 grd Y
200
2400/4160 Y 7200/12470 Y
200
7200/12470 Y 14400/24940 Y
200
14400/24940 Y 19920/34500 grd Y
SECONDARY VOLTAGE RANGE 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
54 x 33 x 34
137 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1700
771
58 x 33 x 34
147 x 84 x 86
1700
771
54 x 42 x 34
137 x 107 x 86
1750
793
54 x 42 x 34
137 x 107 x 86
1750
793
58 x 42 x 34
147 x 107 x 86
1750
793
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc.
TRANSFORMERS VARIABLE SPEED DRIVE TRANSFORMER – 3 PHASE DIMENSIONS SIZE PRIMARY SECONDARY HXDXW KVA VOLTS VOLTAGE RANGE Inches CM 480-960 DELTA 67 480 47 x 35 x 41 119 x 89 x 104 831-1663 WYE 750-1258 DELTA 100 480 54 x 37 x 41 137 x 90 x 104 1300-2160 WYE 750 – 1497 DELTA 142 x 117 x 130 480 56 x 46 x 44 1299 – 2600 WYE 112 750 – 1550 DELTA 130 480 50.5 x 37 x 42 128 x 94 x 107 1299 – 2685 WYE 800-1559 DELTA 173 x 117 x 150 480 68 x 46 x 44 1386 - 2700 WYE 112 1100 – 2200 DELTA 135 x 109.x 200 480 53 X 43 X 51.5 1905 – 3811 WYE 131 1100 – 2200 DELTA 152 x 122 x 210 480 60 x 48 x 50 1905 – 3810 WYE 127 950-1900 DELTA 198 x 132 x 250 415 78 x 52 x 48 1650-3300 WYE 122 1100-2200 DELTA 198 x 132 x 250 480 78 x 52 x 48 1905-3810 WYE 122 1100 – 2200 DELTA 152 x 132 x 260 480 60 X 52 X 48 1905 – 3811 WYE 122 1100 – 2200 DELTA 188 x 137 x 350 480 74 x 54 x 50 1905 – 3811 WYE 127 1100 – 2200 DELTA 57.5 X 45 X 146 x 114 x 355 480 1905 – 3811 WYE 53.5 136 950-1900 DELTA 155 x 155 x 400 415 61 x 61 x 54 1650-3300 WYE 137 1109-2166 DELTA 191 x 155 x 400 480 75 x 61 x 54 1921-3732 WYE 137 1100 – 2200 DELTA 178 x 107 x 400 480 70 X 42 X 62 1905 – 3811 WYE 158 1100-2200 DELTA 198 x 117 x 450 480 78 x 46 x 58 1905-3810 WYE 147 198 x 165 x 1100 – 2200 DELTA 78 x 65 x 54 520 480 1905 – 3811 WYE 137 1300-2601 DELTA 208 x 170 x 750 480 82 x 67 x 60 2252-4505 WYE 152 1320-2640 DELTA 206 x 170 x 750 480 81 x 67 x 62 2286-4572 WYE 157 1400-2800 DELTA 208 x 173 x 850 480 82 x 68 x 62 2424-4850 WYE 157 1400-2800 DELTA 218 x 170 x 1000 480 86 x 67 x 64 2424-4850 WYE 163 Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
WEIGHT
PART NUMBER
Lbs.
Kgs.
2390
1084
136829
2530
1148
136828
2850
1293
136827
2850
1293
1057390
3740
1696
136683
3530
1601
1057017
3850
1746
136826
4220
1914
127729
4220
1914
136682
4220
1914
136825
6540
2967
136824
5350
2427
1054386
6675
3028
127961
6675
3028
136823
4500
2041
1057416
8175
3708
136681
8300
3765
136822
9326
4230
136680
9800
4445
136821
11200 5080
136820
11500 5216
136819
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc.
TRANSFORMERS SPECIALTY TRANSFORMER – 3 PHASE SIZE PRIMARY SECONDARY KVA VOLTS VOLTAGE RANGE 125
6000
150
13800
150
34500
250
13800
250
34500
450
13800
450
34500
500
13800
750
13800
750
34500
1100-2200 DELTA 1905-3810 WYE 800-1559 DELTA 1386-2700 WYE 800-1559 DELTA 1386–2700 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 1905-3811 WYE 1100-2200 DELTA 2200-3810 WYE 1100-2200 DELTA 2200-3810 WYE
Wood Group ESP, Inc. Page-2
DIMENSIONS HXDXW Inches CM 142 x 114 x 56 x 45 x 46 117 198 x 117 x 78 x 46 x 44 112 198 x 117 x 78 x 46 x 44 112 178 x 132 x 70 x 52 x 48 122 198 x 132 x 78 x 52 x 50 127 224 x 165 x 88 x 65 x 54 137 244 x 165 x 96 x 65 x 54 137 193 x 203 x 76 x 80 x 55 140 229 x 170 x 90 x 67 x 60 152 229 x 170 x 90 x 67 x 60 152
The ESP Specialists
WEIGHT
PART NUMBER
Lbs.
Kgs.
3275
1486 136253
3927
1781 136615
3927
1781 136614
4431
2010 136675
4642
2106 136674
8450
3833 136677
8650
3924 136676
6502
2949 136198
9792
4442 136679
10307 4675 136678
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
37.5
480/831 Y
37.5
2400/4160 Y
37.5
7200/12470 Y
37.5
12470 ∆*
37.5
14400/24940 Y
37.5
19920/34500 grd Y
50
480/831 Y
50
2400/4160 Y
50
7200/12470 Y
50
12470 ∆*
50
14400/24940 Y
50
19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
605
274
45 x 23 x 26
114 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
710
322
49 x 23 x 26
124 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc.
TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
75
480/831 Y
75
2400/4160 Y
75
7200/12470 Y
75
12470 ∆*
75
14400/24940 Y
75
19920/34500 grd Y
100
480/831 Y
100
2400/4160 Y
100
7200/12470 Y
100
12470 ∆*
100
14400/24940 Y
100
19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
49 x 28 x 30
124 x 71 x 76
890
404
54 x 28 x 30
137 x 71 x 76
945
429
54 x 28 x 30
137 x 71 x 76
945
429
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
49 x 33 x 30
124 x 84 x 76
975
442
54 x 33 x 30
137 x 84 x 76
1035
469
54 x 33 x 30
137 x 84 x 76
1035
469
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 125 KVA **
PRIMARY VOLTS
167
2400/4160 Y
167
7200/12470 Y
167
12470 ∆
167
14400/24940 Y
167
19920/34500 Y
200
7200/12470 Y
200
12470 ∆
200
14400/24940 Y
200
19920/34500 Y
SECONDARY VOLTAGE RANGE 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
54 x 33 x 34
137 x 84 x 86
1645
746
54 x 33 x 34
137 x 84 x 86
1645
746
54 x 33 x 34
137 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1645
746
54 x 42 x 34
137 x 107 x 86
1700
771
54 x 42 x 34
137 x 107 x 86
1700
771
58 x 42 x 34
147 x 107 x 86
1700
771
58 x 42 x 34
147 x 107 x 86
1700
771
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc.
TRANSFORMERS SINGLE PHASE FACT 225 KVA **
PRIMARY VOLTS
37.5
2400/4160 Y 7200/12470 Y
37.5
7200/12470 Y 14400/24940 Y
37.5
14400/24940 Y 19920/34500 grd Y
50
2400/4160 Y 7200/12470 Y
50
7200/12470 Y 14400/24940 Y
50
14400/24940 Y 19920/34500 grd Y
75
2400/4160 Y 7200/12470 Y
75
7200/12470 Y 14400/24940 Y
75
14400/24940 Y 19920/34500 grd Y
100
2400/4160 Y 7200/12470 Y
100
7200/12470 Y 14400/24940 Y
100
14400/24940 Y 19920/34500 grd Y
SECONDARY VOLTAGE RANGE 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731 – 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y 480 – 1920 ∆ 1731- 2510 ex ∆ 831 – 3325 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
45 x 23 x 26
114 x 58 x 66
605
274
50 x 23 x 26
127 x 58 x 66
635
288
50 x 23 x 26
127 x 58 x 66
635
288
49 x 23 x 26
124 x 58 x 66
710
322
54 x 23 x 26
137 x 58 x 66
750
340
54 x 23 x 26
137 x 58 x 66
750
340
49 x 28 x 30
124 x 71 x 76
890
404
54 x 28 x 30
137 x 71 x 76
945
428
54 x 28 x 30
137 x 71 x 76
945
428
49 x 33 x 30
124 x 84 x 76
975
442
54 x 33 x 30
137 x 84 x 76
1035
469
54 x 33 x 30
137 x 84 x 76
1035
469
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise. Wood Group ESP, Inc. Page-6
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. TRANSFORMERS SINGLE PHASE FACT 225 KVA **
PRIMARY VOLTS
167
2400/4160 Y 7200/12470 Y
167
7200/12470 Y 14400/24940 Y
167
14400/24940 Y 19920/34500 grd Y
200
2400/4160 Y 7200/12470 Y
200
7200/12470 Y 14400/24940 Y
200
14400/24940 Y 19920/34500 grd Y
SECONDARY VOLTAGE RANGE 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y 800 – 3200 ∆ 2884 - 4233 ex ∆ 1386 - 5543 Y
DIMENSIONS HXDXW Inches CM
WEIGHT Lbs.
Kgs.
54 x 33 x 34
137 x 84 x 86
1645
746
58 x 33 x 34
147 x 84 x 86
1700
771
58 x 33 x 34
147 x 84 x 86
1700
771
54 x 42 x 34
137 x 107 x 86
1750
793
54 x 42 x 34
137 x 107 x 86
1750
793
58 x 42 x 34
147 x 107 x 86
1750
793
PART NUMBER
*- Primaries for other delta voltages available upon request. ** - Full KVA capacity at all tap positions without exceeding 65 Degrees C Rise.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Transformers - Copyright Wood Group ESP, Inc. - O c t o b e r , 2 0 0 9
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with G 513 Series SP1000 Pumps.
G 513 SERIES SP1000
(TG4000) G0120 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
5
G0120 CMP 05 STG
3292
2.1
14
1
1
1
1
1
1
11
G0120 CMP 11 STG
3360
3.5
14
1
1
1
1
1
1
18 25
G0120 CMP 18 STG G0120 CMP 25 STG
3428 3552
4.9 6.3
14
1 2
1 1
1 1
1 1
1 1
1 1
32 38
G0120 CMP 32 STG G0120 CMP 38 STG
3620 3687
7.7 9.1
14 14
2 2
1 1
1 1
1 1
1 1
1 1
45
G0120 CMP 45 STG
4212
10.5
18
3
1
1
1
1
1
52
G0120 CMP 52 STG
4280
11.9
18
3
1
1
1
1
1
59
G0120 CMP 59 STG
4347
13.3
18
3
1
1
1
1
1
65
G0120 CMP 65 STG
5072
14.7
22
4
1
1
1
1
1
73
G0120 CMP 73 STG
5140
16.1
22
4
1
1
1
1
1
79
G0120 CMP 79 STG
5199
17.5
22
4
1
1
1
1
1
86
G0120 CMP 86 STG
5832
18.9
26
5
1
1
1
1
1
92
G0120 CMP 92 STG
5899
20.4
26
5
1
1
1
1
1
100
G0120 CMP 100 STG
5959
21.8
26
5
1
1
1
1
1
104
(2) 52 STG
6710
23.8
30
6
1
1
1
1
1
111
(1) 59 STG + (1) 52 STG
6777
25.2
30
6
1
1
1
1
1
118
(2) 59 STG
7309
26.6
34
7
1
1
1
1
1
124
(1) 65 STG + (1) 59 STG
7369
28
34
7
1
1
1
1
1
130
(2) 65 STG
7429
29.4
34
7
1
1
1
1
1
138
(1) 73 STG + (1) 65 STG
8062
30.8
38
8
1
1
1
1
1
146
(2) 73 STG
7130
32.2
38
8
1
1
1
1
1
152
(1) 79 STG + (1) 73 STG
8129
33.6
38
8
1
1
1
1
1
158
(2) 79 STG
8913
35
38
4
9
1
1
1
1
1
165
(1) 86 STG + (1) 79 STG
8981
36.4
38
4
9
1
1
1
1
1
172
(2) 86 STG
9049
37.8
38
4
9
1
1
1
1
1
178
(1) 92 STG + (1) 86 STG
9581
39.3
38
8
10
1
1
1
1
1
184
(2) 92 STG
9648
40.8
38
8
10
1
1
1
1
1
14
THRUST LIMIT: 60Hz = 186 stages, 50Hz = 167 stages (for Higher Pressures, Floater Pumps may be suitable). Consider E0080 or E0170 Pumps if feasible. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with G 513 Series SP1000 Pumps.
(TG4000) G0120
G 513 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
192
(1) 100 STG + (1) 92STG
10273
42.2
38
12
11
1
1
1
1
200 205
(2) 100 STG (1) 73 STG + (2) 66 STG
10333 10419
43.6 45.5
38 38
12 12
11 11
1 1
1 1
1 1
1 1
212 219 225
(2) 73 STG + (1) 66 STG (3) 73 STG (1) 79 STG + (2) 73 STG
11052 11120 11179
46.9 48.3 49.7
38 38 38
16 16 16
12 12 12
1 1 1
1 1 1
1 1 1
1 1 1
231 237
(2) 79 STG + (1) 73 STG (3) 79 STG
11803 11862
51.1 52.5
38 38
20 20
13 13
1 1
1 1
1 1
1 1
244
(1) 86 STG + (2) 79 STG
11930
53.9
38
20
13
1
1
1
1
251
(2) 86 STG + (1) 79 STG
12563
55.3
38
24
14
1
1
1
1
258 264 270
(3) 86 STG (1) 92 STG + (2) 86 STG (2) 92 STG + (1) 86 STG
12631 13363 13430
56.7 58.2 59.7
38 38 38
24 28 28
14 15 15
1 1 1
1 1 1
1 1 1
1 1 1
THRUST LIMIT: 60Hz = 186 stages, 50Hz = 167 stages (for Higher Pressures, Floater Pumps may be suitable). Consider E0080 or E0170 Pumps if feasible. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
(TE1500) E0050
E 562 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
7
E0050 CMP 07 STG
3332
2.5
14
1
1
1
1
1
1
14
E0050 CMP 14 STG
3393
4.0
14
1
1
1
1
1
1
22
E0050 CMP 22 STG
3460
5.5
14
1
1
1
1
1
1
30 37
E0050 CMP 30 STG E0050 CMP 37 STG
3592 3653
7.0 8.5
14 14
2 2
1 1
1 1
1 1
1 1
1 1
45
E0050 CMP 45 STG
4185
10.0
18
3
1
1
1
1
1
52
E0050 CMP 52 STG
4247
11.5
18
3
1
1
1
1
1
60
E0050 CMP 60 STG
4314
13.0
18
3
1
1
1
1
1
68
E0050 CMP 68 STG
5045
14.5
22
4
1
1
1
1
1
75
E0050 CMP 75 STG
5107
16.0
22
4
1
1
1
1
1
83
E0050 CMP 83 STG
5174
17.5
22
4
1
1
1
1
1
5800
19.0
26
5
1
1
1
1
1
20.5 23.0
26 30
5 6
1 1
1 1
1 1
1 1
1 1
90
E0050 CMP 90 STG
98 104
E0050 CMP 98 STG (2) 52 STG
5867 6644
112
(1) 60 STG + (1) 52 STG
6711
24.5
30
6
1
1
1
1
1
120
(2) 60 STG
7243
26.0
34
7
1
1
1
1
1
128
(1) 68 STG + (1) 60 STG
7309
27.5
34
7
1
1
1
1
1
136
(2) 68 STG
7275
29.0
34
7
1
1
1
1
1
143
(1) 75 STG + (1) 68 STG
8002
30.5
38
8
1
1
1
1
1
150
(2) 75 STG
8064
32.0
38
8
1
1
1
1
1
158
(1) 83 STG + (1) 75 STG
8131
33.5
38
8
1
1
1
1
1
166
(2) 83 STG
8863
35.0
38
4
9
1
1
1
1
1
173
(1) 90 STG + (1) 83 STG
8924
36.5
38
4
9
1
1
1
1
1
180
(2) 90 STG
9450
38.0
38
8
10
1
1
1
1
1
188
(1) 98 STG + (1) 90 STG
9517
39.5
38
8
10
1
1
1
1
1
196
(2) 98 STG
9584
41.0
38
8
10
1
1
1
1
1
204
(3) 68 STG
10270
43.5
38
12
11
1
1
1
1
1
THRUST LIMIT: 60Hz = 140 stages, 50Hz = 202 stages (for Higher Pressures, Floater Pumps may be suitable). Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
E 562 SERIES SP1000
(TE2700) E0080 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
7
E0080 CMP 07 STG
3332
2.5
14
1
1
1
1
1
1
14
E0080 CMP 14 STG
3393
4.0
14
1
1
1
1
1
1
22
E0080 CMP 22 STG
3460
5.5
14
1
1
1
1
1
1
30
E0080 CMP 30 STG
3592
7.0
14
2
1
1
1
1
1
37
E0080 CMP 37 STG
3653
8.5
14
2
1
1
1
1
1
45
E0080 CMP 45 STG
4185
10.0
18
3
1
1
1
1
1
52 60
E0080 CMP 52 STG E0080 CMP 60 STG
4247 4314
11.5 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
68
E0080 CMP 68 STG
5045
14.5
22
4
1
1
1
1
1
75
E0080 CMP 75 STG
5107
16.0
22
4
1
1
1
1
1
83
E0080 CMP 83 STG
5174
17.5
22
4
1
1
1
1
1
90 98
E0080 CMP 90 STG E0080 CMP 98 STG
5800 5867
19.0 20.5
26 26
5 5
1 1
1 1
1 1
1 1
1 1
104
(2) 52 STG
6644
23.0
30
6
1
1
1
1
1
112
(1) 60 STG + (1) 52 STG
6711
24.5
30
6
1
1
1
1
1
120
(2) 60 STG
7243
26.0
34
7
1
1
1
1
1
128
(1) 68 STG + (1) 60 STG
7309
27.5
34
7
1
1
1
1
1
136
(2) 68 STG
7275
29.0
34
7
1
1
1
1
1
143
(1) 75 STG + (1) 68 STG
8002
30.5
38
8
1
1
1
1
1
150
(2) 75 STG
8064
32.0
38
8
1
1
1
1
1
158
(1) 83 STG + (1) 75 STG
8131
33.5
38
8
1
1
1
1
1
166
(2) 83 STG
8863
35.0
38
4
9
1
1
1
1
1
173
(1) 90 STG + (1) 83 STG
8924
36.5
38
4
9
1
1
1
1
1
180
(2) 90 STG
9450
38.0
38
8
10
1
1
1
1
1
188
(1) 98 STG + (1) 90 STG
9517
39.5
38
8
10
1
1
1
1
1
196
(2) 98 STG
9584
41.0
38
8
10
1
1
1
1
1
THRUST LIMIT: 60Hz = 140 stages, 50Hz = 202 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
E 562 SERIES SP1000
(TE5500) E0170 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases 5 11
E0170 CMP 05 STG E0170 CMP 11 STG
3330 3395
2.5 4.0
14 14
1 1
1 1
1 1
1 1
1 1
1 1
17
E0170 CMP 17 STG
3460
5.5
14
1
1
1
1
1
1
23
E0170 CMP 23 STG
3591
7.0
14
2
1
1
1
1
1
29
E0170 CMP 29 STG
3656
E0170 CMP 35 STG E0170 CMP 41 STG E0170 CMP 47 STG E0170 CMP 53 STG E0170 CMP 59 STG E0170 CMP 65 STG E0170 CMP 71 STG E0170 CMP 77 STG E0170 CMP 83 STG E0170 CMP 89 STG (2) 47 STG (1) 53 STG + (1) 47 STG (2) 53 STG (1) 59 STG + (1) 53 STG (2) 59 STG (1) 65 STG + (1) 59 STG (2) 65 STG (1) 71 STG + (1) 65 STG (2) 71 STG (1) 77 STG + (1) 71 STG (2) 77 STG (1) 83 STG + (1) 77 STG (2) 83 STG (1) 89 STG + (1) 83 STG (2) 89 STG (1) 65 STG + (2) 59 STG (2) 65 STG + (1) 59 STG (3) 65 STG (1) 71 STG + (2) 65 STG
4186 4252 4317 5047 5113 5178 5808 5874 6604 6669 7249 7314 7379 8010 7076 8141 8871 8936 9466 9532 9598 10228 10293 10358 10988 11104 11734 11799 12429
35 41 47 53 59 65 71 77 83 89 94 100 106 112 118 124 130 136 142 148 154 160 166 172 178 183 189 195 201
8.5
14
2
1
1
1
1
1
10.0 11.5 13.0 14.5 16.0 17.5 19.0 20.5 22.0 23.5 26.0 27.5 29.0 30.5 32.0 33.5 35.0 36.5 38.0 39.5 41.0 42.5 44.0 45.5 47.0 49.5 51.0 52.5 54.0
18 18 18 22 22 22 26 26 30 30 34 34 34 34 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38
3 3 3 4 4 4 5 5 6 6 7 7 7 8 8 8 9 9 10 10 10 11 11 11 12 12 13 13 14
1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4 4 8 8 8 12 12 12 16 16 20 20 24
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
THRUST LIMIT: 60Hz = 138 stages, 50Hz = 199 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
(TE7000) E0220
E 562 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
154 160 166 172 178 183 189 195 201 207 213 219 225 231 237 243 249 255 261 267 272
(2) 77 STG HSS (1) 83 STG + (1) 77 UHSS (2) 83 STG UHSS (1) 89 STG + (1) 83 UHSS (2) 89 STG UHSS (1) 65 STG + (2) 59 UHSS (2) 65 STG + (1) 59 UHSS (3) 65 STG UHSS (1) 71 STG + (2) 65 UHSS (2) 71 STG + (1) 65 UHSS (3) 71 STG UHSS (1) 77 STG + (2) 71 UHSS (2) 77 STG + (1) 71 UHSS (3) 77 STG UHSS (1) 83 STG + (2) 77 UHSS (2) 83 STG + (1) 77 UHSS (3) 83 STG UHSS (1) 89 STG + (2) 83 UHSS (2) 89 STG + (1) 83 UHSS (3) 89 STG UHSS (2) 71 STG + (2) 65 UHSS
STG
STG
STG STG
STG STG
STG STG
STG STG
STG STG
STG
9598
41.0
38
8
10
1
1
1
1
1
10228
42.5
38
12
11
1
1
1
1
1
10293
44.0
38
12
11
1
1
1
1
1
10358
45.5
38
12
11
1
1
1
1
1
10988
47.0
38
16
12
1
1
1
1
1
11104
49.5
38
16
12
1
1
1
1
1
11734
51.0
38
20
13
1
1
1
1
1
11799
52.5
38
20
13
1
1
1
1
1
12429
54.0
38
24
14
1
1
1
1
1
12244
55.5
38
24
14
1
1
1
1
1
12309
57.0
38
24
14
1
1
1
1
1
13040
58.5
38
28
15
1
1
1
1
1
13106
60.0
38
28
15
1
1
1
1
1
13172
61.5
38
28
15
1
1
1
1
1
13702
63.0
38
32
16
1
1
1
1
1
13767
64.5
38
32
16
1
1
1
1
1
14397
66.0
38
36
17
1
1
1
1
1
14462
67.5
38
36
17
1
1
1
1
1
14527
69.0
38
36
17
1
1
1
1
1
15257
70.5
38
40
18
1
1
1
1
1
15372
73.0
38
40
18
1
1
1
1
1
THRUST LIMIT: 60Hz = 188 stages, 50Hz = 270 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ7500) J0240 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2
J0240 CMP 02 STG
3425
2.7
14
1
1
1
1
1
1
6
J0240 CMP 06 STG
3542
4.0
14
1
1
1
1
1
1
9
J0240 CMP 09 STG
3634
5.4
14
1
1
1
1
1
1
12
J0240 CMP 12 STG
3791
6.8
14
2
1
1
1
1
1
15
J0240 CMP 15 STG
3883
8.2
14
2
1
1
1
1
1
19
J0240 CMP 19 STG
3994
9.5
14
2
1
1
1
1
1
22
J0240 CMP 22 STG
4551
10.9
18
3
1
1
1
1
1
25
J0240 CMP 25 STG
4643
12.3
18
3
1
1
1
1
1
29
J0240 CMP 29 STG
4754
13.7
18
3
1
1
1
1
1
32
J0240 CMP 32 STG
5514
15.0
22
4
1
1
1
1
1
35
J0240 CMP 35 STG
5603
16.4
22
4
1
1
1
1
1
39
J0240 CMP 39 STG
6279
17.8
26
5
1
1
1
1
1
42
J0240 CMP 42 STG
6371
19.2
26
5
1
1
1
1
1
45
J0240 CMP 45 STG
6463
20.5
26
5
1
1
1
1
1
48
J0240 CMP 48 STG
7220
21.9
30
6
1
1
1
1
1
50
(2) 25 STG
7436
24.6
30
6
1
1
1
1
1
54
(1) 29 STG + (1) 25 STG
8012
26.0
34
7
1
1
1
1
1
58
(2) 29 STG
8123
27.4
34
7
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8218
28.7
34
7
1
1
1
1
1
64
(2) 32 STG
8878
30.0
38
8
1
1
1
1
1
67
(1) 35 STG + (1) 32 STG
8967
31.4
38
8
1
1
1
1
1
70
(2) 35 STG
9056
32.8
38
8
1
1
1
1
1
74
(1) 39 STG + (1) 35 STG
9832
34.2
38
4
9
1
1
1
1
1
78
(2) 39 STG
9943
35.6
38
4
9
1
1
1
1
1
81
(1) 42 STG + (1) 39 STG
10035
37.0
38
4
9
1
1
1
1
1
84
(2) 42 STG
10592
38.4
38
8
10
1
1
1
1
1
THRUST LIMIT: 60Hz = 83 stages, 50Hz = 119 stages . Consider E0220 pump.
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ7500) J0240 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
87 90
(1) 45 STG + (1) 42 STG (2) 45 STG
10684 10776
39.7 41.0
38 38
8 8
10 10
1 1
1 1
1 1
1 1
1 1
93 96
(1) 48 STG + (1) 45 STG (2) 48 STG
11433 11525
42.4 43.8
38 38
12 12
11 11
1 1
1 1
1 1
1 1
1 1
99 102
(1) 53 STG + (2) 32 STG (2) 35 STG + (1) 32 STG
12331 12420
46.4 47.8
38 38
16 16
12 12
1 1
1 1
1 1
1
1 1
105 109
(3) 35STG (1) 39 STG + (2) 35 STG
12259 12935
49.2 50.6
38 38
16 20
12 13
1 1
1 1
1 1
1 1
113
(2) 39 STG + (1) 35 STG
13046
52.0
38
20
13
1
1
1
1
117 120
(3) 39STG (1) 42 STG + (2) 39 STG
13157 13814
53.4 54.8
38 38
20 14
13 14
1 1
1 1
1 1
1 1
THRUST LIMIT: 60Hz = 83 stages, 50Hz = 119 stages . Consider E0220 pump.
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ9000) J0270 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2
J0270 CMP 02 STG
3425
2.7
14
1
1
1
1
1
1
6
J0270 CMP 06 STG
3543
4.0
14
1
1
1
1
1
1
9
J0270 CMP 09 STG
3636
5.4
14
1
1
1
1
1
1
12
J0270 CMP 12 STG
3793
6.8
14
2
1
1
1
1
1
15
J0270 CMP 15 STG
3886
8.2
14
2
1
1
1
1
1
19
J0270 CMP 19 STG
3998
9.5
14
2
1
1
1
1
1
22
J0270 CMP 22 STG
4555
10.9
18
3
1
1
1
1
1
25
J0270 CMP 25 STG
4648
12.3
18
3
1
1
1
1
1
29
J0270 CMP 29 STG
4760
13.7
18
3
1
1
1
1
1
32
J0270 CMP 32 STG
5520
15.0
22
4
1
1
1
1
1
35
J0270 CMP 35 STG
5610
16.4
22
4
1
1
1
1
1
39
J0270 CMP 39 STG
6287
17.8
26
5
1
1
1
1
1
42
J0270 CMP 42 STG
6379
19.2
26
5
1
1
1
1
1
45
J0270 CMP 45 STG
6472
20.5
26
5
1
1
1
1
1
48
J0270 CMP 48 STG
7230
21.9
30
6
1
1
1
1
1
50
(2) 25 STG
7446
24.6
30
6
1
1
1
1
1
54
(1) 29 STG + (1) 25 STG
8023
26.0
34
7
1
1
1
1
1
58
(2) 29 STG
8135
27.4
34
7
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8230
28.7
34
7
1
1
1
1
1
64
(2) 32 STG
8890
30.0
38
8
1
1
1
1
1
67
(1) 35 STG + (1) 32 STG
8730
31.4
38
8
1
1
1
1
1
70
(2) 35 STG
8820
32.8
38
8
1
1
1
1
1
74
(1) 39 STG + (1) 35 STG
9597
34.2
38
9
1
1
1
1
1
78
(2) 39 STG
9709
35.6
38
4
9
1
1
1
1
1
81
(1) 42 STG + (1) 39 STG
9801
37.0
38
4
9
1
1
1
1
1
84
(2) 42 STG
10358
38.4
38
8
10
1
1
1
1
1
4
87 (1) 45 STG + (1) 42 STG 10451 39.7 38 8 10 1 THRUST LIMIT: 60Hz = 60 stages, 50Hz = 86 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-10
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
1
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ12000) J0360 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2 5 8
J0360 CMP 02 STG J0360 CMP 05 STG J0360 CMP 08 STG
3400 3483 3564
2.7 4.0 5.4
14 14 14
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 14
J0360 CMP 11 STG J0360 CMP 14 STG
3712 3795
6.8 8.2
14 14
2 2
1 1
1 1
1 1
1 1
1 1
17 20
J0360 CMP 17 STG J0360 CMP 20 STG
3877 4423
9.5 10.9
14 18
2 3
1 1
1 1
1 1
1 1
1 1
23 26 29
J0360 CMP 23 STG J0360 CMP 26 STG J0360 CMP 29 STG
4506 4589 5337
12.3 13.7 15.0
18 18 22
3 3 4
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
32 35
J0360 CMP 32 STG J0360 CMP 35 STG
5418 6065
16.4 17.8
22 26
4 5
1 1
1 1
1 1
1 1
1
38 41
J0360 CMP 38 STG J0360 CMP 41 STG
6149 6231
19.2 20.5
26 26
5 5
1 1
1 1
1 1
1 1
1 1
44
J0360 CMP 44 STG
6978
21.9
30
6
1
1
1
1
1
46
(2) 23 STG
7162
24.6
30
6
1
1
1
1
1
49 52 55
(1) 26 STG + (1) 23 STG (2) 26 STG (1) 29 STG + (1) 26 STG
7710 7793 7876
26.0 27.4 28.7
34 34 34
7 7 7
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
58
(2) 29 STG
8524
30.0
38
8
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8605
31.4
38
8
1
1
1
1
1
64 67
(2) 32 STG (1) 35 STG + (1) 32 STG
8686 9333
32.8 34.2
38 38
8 9
1 1
1 1
1 1
1 1
1 1
4
1
70 (2) 35 STG 9415 35.6 38 4 9 1 1 1 1 1 THRUST LIMIT: 60Hz = 60 stages, 50Hz = 86 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with M 950 Series SP1000 Pumps.
M 950 SERIES SP1000
(TM19000) M0560 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
8 9 10
M0560 CMP A-CUT 08 STG M0560 CMP A-CUT 09 STG M0560 CMP A-CUT 10 STG
4198 4266 4326
6.3 6.9 7.5
14 14 14
2 2 2
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 12
M0560 CMP A-CUT 11 STG M0560 CMP A-CUT 12 STG
4393 4461
8.1 8.7
14 14
2 2
1 1
1 1
1 1
1 1
1 1
13 14
M0560 CMP A-CUT 13 STG M0560 CMP A-CUT 14 STG
4528 5060
9.3 9.9
14 18
2 3
1 1
1 1
1 1
1 1
1 1
15 16 17
M0560 CMP A-CUT 15 STG M0560 CMP A-CUT 16 STG M0560 CMP A-CUT 17 STG
5127 5195 5266
10.6 11.2 11.8
18 18 18
3 3 3
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
18 19
M0560 CMP A-CUT 18 STG M0560 CMP A-CUT 19 STG
5333 5396
12.4 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
20 21
M0560 CMP A-CUT 20 STG M0560 CMP A-CUT 21 STG
5464 6199
13.6 14.2
18 22
3 4
1 1
1 1
1 1
1 1
1
22
M0560 CMP A-CUT 22 STG
6266
14.8
22
4
1
1
1
1
1
23
M0560 CMP A-CUT 23 STG
6331
15.4
22
4
1
1
1
1
1
24 25 26
M0560 CMP A-CUT 24 STG M0560 CMP A-CUT 25 STG M0560 CMP A-CUT 26 STG
6398 6468 6536
16.0 16.6 17.2
22 22 22
4 4 4
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
27
M0560 CMP A-CUT 27 STG
7168
17.8
26
5
1
1
1
1
1
28
M0560 CMP A-CUT 28 STG
7232
18.4
26
5
1
1
1
1
1
29 30
M0560 CMP A-CUT 29 STG M0560 CMP A-CUT 30 STG
7302 7369
19.0 19.6
26 26
5 5
1 1
1 1
1 1
1 1
1 1
1
31 M0560 CMP A-CUT 31 STG 7437 20.2 26 5 1 1 1 1 1 THRUST LIMIT: 60Hz = 21 stages, 50Hz = 31 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with M 950 Series SP1000 Pumps.
M 950 SERIES SP1000
(TM24000) M0700 Discharge Assembly 6” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
8 9 10
M0700 CMP A-CUT 08 STG M0700 CMP A-CUT 09 STG M0700 CMP A-CUT 10 STG
4198 4266 4326
6.3 6.9 7.5
14 14 14
2 2 2
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 12
M0700 CMP A-CUT 11 STG M0700 CMP A-CUT 12 STG
4393 4461
8.1 8.7
14 14
2 2
1 1
1 1
1 1
1 1
1 1
13 14 15
M0700 CMP A-CUT 13 STG M0700 CMP A-CUT 14 STG M0700 CMP A-CUT 15 STG
4528 5060 5127
9.3 9.9 10.6
14 18 18
2 3 3
1 1 1
1 1 1
1 1 1
1 1 1
1
16 17
M0700 CMP A-CUT 16 STG M0700 CMP A-CUT 17 STG
5195 5266
11.2 11.8
18 18
3 3
1 1
1 1
1 1
1 1
1 1
18 19
M0700 CMP A-CUT 18 STG M0700 CMP A-CUT 19 STG
5333 5396
12.4 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
M0700 CMP A-CUT 20 STG
5464
13.6
18
3
1
1
1
1
1
6199
14.2
22
4
1
1
1
1
1
6266
14.8
22
4
1
1
1
1
1
6331
15.4
22
4
1
1
1
1
1
6398
16.0
22
4
1
1
1
1
1
6468
16.6
22
4
1
1
1
1
1
6536
17.2
22
4
1
1
1
1
1
7168
17.8
26
5
1
1
1
1
1
7232
18.4
26
5
1
1
1
1
1
7302
19.0
26
5
1
1
1
1
1
7369
19.6
26
5
1
1
1
1
1
7437
20.2
26
5
1
1
1
1
1
20 21 22 23 24 25 26 27 28 29 30 31
M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS
CMP A-CUT 21 STG CMP A-CUT 22 STG CMP A-CUT 23 STG CMP A-CUT 24 STG CMP A-CUT 25 STG CMP A-CUT 26 STG CMP A-CUT 27 STG CMP A-CUT 28 STG CMP A-CUT 29 STG CMP A-CUT 30 STG CMP A-CUT 31 STG
1 1
THRUST LIMIT: 60Hz = 22 stages, 50Hz = 31 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with N 950 Series SP1000 Pumps.
N 950 SERIES SP1000
(TN35000) N1150 Discharge Assembly 6” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
1
N1150 CMP A-CUT 1 STG
3786
2.4
14
1
1
1
1
1
1
2
N1150 CMP A-CUT 2 STG
3862
3.0
14
1
1
1
1
1
1
3
N1150 CMP A-CUT 3 STG
3938
3.6
14
1
1
1
1
1
1
4
N1150 CMP A-CUT 4 STG
4014
4.2
14
1
1
1
1
1
1
5
N1150 CMP A-CUT 5 STG
4087
4.7
14
1
1
1
1
1
1
6
N1150 CMP A-CUT 6 STG
4162
5.3
14
1
1
1
1
1
1
7
N1150 CMP A-CUT 7 STG
4303
5.9
14
2
1
1
1
1
1
8
N1150 CMP A-CUT 8 STG
4379
6.5
14
2
1
1
1
1
1
9
N1150 CMP A-CUT 9 STG
4455
7.1
14
2
1
1
1
1
1
10
N1150 CMP A-CUT 10STG
4528
7.6
14
2
1
1
1
1
1
11
N1150 CMP A-CUT 11STG
4604
8.2
14
2
1
1
1
1
1
THRUST LIMIT: 60Hz = 8 stages, 50Hz = 11 stages. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-14
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with G 513 Series SP1000 Pumps.
G 513 SERIES SP1000
(TG4000) G0120 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
5
G0120 CMP 05 STG
3292
2.1
14
1
1
1
1
1
1
11
G0120 CMP 11 STG
3360
3.5
14
1
1
1
1
1
1
18 25
G0120 CMP 18 STG G0120 CMP 25 STG
3428 3552
4.9 6.3
14
1 2
1 1
1 1
1 1
1 1
1 1
32 38
G0120 CMP 32 STG G0120 CMP 38 STG
3620 3687
7.7 9.1
14 14
2 2
1 1
1 1
1 1
1 1
1 1
45
G0120 CMP 45 STG
4212
10.5
18
3
1
1
1
1
1
52
G0120 CMP 52 STG
4280
11.9
18
3
1
1
1
1
1
59
G0120 CMP 59 STG
4347
13.3
18
3
1
1
1
1
1
65
G0120 CMP 65 STG
5072
14.7
22
4
1
1
1
1
1
73
G0120 CMP 73 STG
5140
16.1
22
4
1
1
1
1
1
79
G0120 CMP 79 STG
5199
17.5
22
4
1
1
1
1
1
86
G0120 CMP 86 STG
5832
18.9
26
5
1
1
1
1
1
92
G0120 CMP 92 STG
5899
20.4
26
5
1
1
1
1
1
100
G0120 CMP 100 STG
5959
21.8
26
5
1
1
1
1
1
104
(2) 52 STG
6710
23.8
30
6
1
1
1
1
1
111
(1) 59 STG + (1) 52 STG
6777
25.2
30
6
1
1
1
1
1
118
(2) 59 STG
7309
26.6
34
7
1
1
1
1
1
124
(1) 65 STG + (1) 59 STG
7369
28
34
7
1
1
1
1
1
130
(2) 65 STG
7429
29.4
34
7
1
1
1
1
1
138
(1) 73 STG + (1) 65 STG
8062
30.8
38
8
1
1
1
1
1
146
(2) 73 STG
7130
32.2
38
8
1
1
1
1
1
152
(1) 79 STG + (1) 73 STG
8129
33.6
38
8
1
1
1
1
1
158
(2) 79 STG
8913
35
38
4
9
1
1
1
1
1
165
(1) 86 STG + (1) 79 STG
8981
36.4
38
4
9
1
1
1
1
1
172
(2) 86 STG
9049
37.8
38
4
9
1
1
1
1
1
178
(1) 92 STG + (1) 86 STG
9581
39.3
38
8
10
1
1
1
1
1
184
(2) 92 STG
9648
40.8
38
8
10
1
1
1
1
1
14
THRUST LIMIT: 60Hz = 186 stages, 50Hz = 167 stages (for Higher Pressures, Floater Pumps may be suitable). Consider E0080 or E0170 Pumps if feasible. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-1
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with G 513 Series SP1000 Pumps.
(TG4000) G0120
G 513 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
192
(1) 100 STG + (1) 92STG
10273
42.2
38
12
11
1
1
1
1
200 205
(2) 100 STG (1) 73 STG + (2) 66 STG
10333 10419
43.6 45.5
38 38
12 12
11 11
1 1
1 1
1 1
1 1
212 219 225
(2) 73 STG + (1) 66 STG (3) 73 STG (1) 79 STG + (2) 73 STG
11052 11120 11179
46.9 48.3 49.7
38 38 38
16 16 16
12 12 12
1 1 1
1 1 1
1 1 1
1 1 1
231 237
(2) 79 STG + (1) 73 STG (3) 79 STG
11803 11862
51.1 52.5
38 38
20 20
13 13
1 1
1 1
1 1
1 1
244
(1) 86 STG + (2) 79 STG
11930
53.9
38
20
13
1
1
1
1
251
(2) 86 STG + (1) 79 STG
12563
55.3
38
24
14
1
1
1
1
258 264 270
(3) 86 STG (1) 92 STG + (2) 86 STG (2) 92 STG + (1) 86 STG
12631 13363 13430
56.7 58.2 59.7
38 38 38
24 28 28
14 15 15
1 1 1
1 1 1
1 1 1
1 1 1
THRUST LIMIT: 60Hz = 186 stages, 50Hz = 167 stages (for Higher Pressures, Floater Pumps may be suitable). Consider E0080 or E0170 Pumps if feasible. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-2
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
(TE1500) E0050
E 562 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
7
E0050 CMP 07 STG
3332
2.5
14
1
1
1
1
1
1
14
E0050 CMP 14 STG
3393
4.0
14
1
1
1
1
1
1
22
E0050 CMP 22 STG
3460
5.5
14
1
1
1
1
1
1
30 37
E0050 CMP 30 STG E0050 CMP 37 STG
3592 3653
7.0 8.5
14 14
2 2
1 1
1 1
1 1
1 1
1 1
45
E0050 CMP 45 STG
4185
10.0
18
3
1
1
1
1
1
52
E0050 CMP 52 STG
4247
11.5
18
3
1
1
1
1
1
60
E0050 CMP 60 STG
4314
13.0
18
3
1
1
1
1
1
68
E0050 CMP 68 STG
5045
14.5
22
4
1
1
1
1
1
75
E0050 CMP 75 STG
5107
16.0
22
4
1
1
1
1
1
83
E0050 CMP 83 STG
5174
17.5
22
4
1
1
1
1
1
5800
19.0
26
5
1
1
1
1
1
20.5 23.0
26 30
5 6
1 1
1 1
1 1
1 1
1 1
90
E0050 CMP 90 STG
98 104
E0050 CMP 98 STG (2) 52 STG
5867 6644
112
(1) 60 STG + (1) 52 STG
6711
24.5
30
6
1
1
1
1
1
120
(2) 60 STG
7243
26.0
34
7
1
1
1
1
1
128
(1) 68 STG + (1) 60 STG
7309
27.5
34
7
1
1
1
1
1
136
(2) 68 STG
7275
29.0
34
7
1
1
1
1
1
143
(1) 75 STG + (1) 68 STG
8002
30.5
38
8
1
1
1
1
1
150
(2) 75 STG
8064
32.0
38
8
1
1
1
1
1
158
(1) 83 STG + (1) 75 STG
8131
33.5
38
8
1
1
1
1
1
166
(2) 83 STG
8863
35.0
38
4
9
1
1
1
1
1
173
(1) 90 STG + (1) 83 STG
8924
36.5
38
4
9
1
1
1
1
1
180
(2) 90 STG
9450
38.0
38
8
10
1
1
1
1
1
188
(1) 98 STG + (1) 90 STG
9517
39.5
38
8
10
1
1
1
1
1
196
(2) 98 STG
9584
41.0
38
8
10
1
1
1
1
1
204
(3) 68 STG
10270
43.5
38
12
11
1
1
1
1
1
THRUST LIMIT: 60Hz = 140 stages, 50Hz = 202 stages (for Higher Pressures, Floater Pumps may be suitable). Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-3
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
E 562 SERIES SP1000
(TE2700) E0080 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
7
E0080 CMP 07 STG
3332
2.5
14
1
1
1
1
1
1
14
E0080 CMP 14 STG
3393
4.0
14
1
1
1
1
1
1
22
E0080 CMP 22 STG
3460
5.5
14
1
1
1
1
1
1
30
E0080 CMP 30 STG
3592
7.0
14
2
1
1
1
1
1
37
E0080 CMP 37 STG
3653
8.5
14
2
1
1
1
1
1
45
E0080 CMP 45 STG
4185
10.0
18
3
1
1
1
1
1
52 60
E0080 CMP 52 STG E0080 CMP 60 STG
4247 4314
11.5 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
68
E0080 CMP 68 STG
5045
14.5
22
4
1
1
1
1
1
75
E0080 CMP 75 STG
5107
16.0
22
4
1
1
1
1
1
83
E0080 CMP 83 STG
5174
17.5
22
4
1
1
1
1
1
90 98
E0080 CMP 90 STG E0080 CMP 98 STG
5800 5867
19.0 20.5
26 26
5 5
1 1
1 1
1 1
1 1
1 1
104
(2) 52 STG
6644
23.0
30
6
1
1
1
1
1
112
(1) 60 STG + (1) 52 STG
6711
24.5
30
6
1
1
1
1
1
120
(2) 60 STG
7243
26.0
34
7
1
1
1
1
1
128
(1) 68 STG + (1) 60 STG
7309
27.5
34
7
1
1
1
1
1
136
(2) 68 STG
7275
29.0
34
7
1
1
1
1
1
143
(1) 75 STG + (1) 68 STG
8002
30.5
38
8
1
1
1
1
1
150
(2) 75 STG
8064
32.0
38
8
1
1
1
1
1
158
(1) 83 STG + (1) 75 STG
8131
33.5
38
8
1
1
1
1
1
166
(2) 83 STG
8863
35.0
38
4
9
1
1
1
1
1
173
(1) 90 STG + (1) 83 STG
8924
36.5
38
4
9
1
1
1
1
1
180
(2) 90 STG
9450
38.0
38
8
10
1
1
1
1
1
188
(1) 98 STG + (1) 90 STG
9517
39.5
38
8
10
1
1
1
1
1
196
(2) 98 STG
9584
41.0
38
8
10
1
1
1
1
1
THRUST LIMIT: 60Hz = 140 stages, 50Hz = 202 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-4
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
E 562 SERIES SP1000
(TE5500) E0170 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases 5 11
E0170 CMP 05 STG E0170 CMP 11 STG
3330 3395
2.5 4.0
14 14
1 1
1 1
1 1
1 1
1 1
1 1
17
E0170 CMP 17 STG
3460
5.5
14
1
1
1
1
1
1
23
E0170 CMP 23 STG
3591
7.0
14
2
1
1
1
1
1
29
E0170 CMP 29 STG
3656
E0170 CMP 35 STG E0170 CMP 41 STG E0170 CMP 47 STG E0170 CMP 53 STG E0170 CMP 59 STG E0170 CMP 65 STG E0170 CMP 71 STG E0170 CMP 77 STG E0170 CMP 83 STG E0170 CMP 89 STG (2) 47 STG (1) 53 STG + (1) 47 STG (2) 53 STG (1) 59 STG + (1) 53 STG (2) 59 STG (1) 65 STG + (1) 59 STG (2) 65 STG (1) 71 STG + (1) 65 STG (2) 71 STG (1) 77 STG + (1) 71 STG (2) 77 STG (1) 83 STG + (1) 77 STG (2) 83 STG (1) 89 STG + (1) 83 STG (2) 89 STG (1) 65 STG + (2) 59 STG (2) 65 STG + (1) 59 STG (3) 65 STG (1) 71 STG + (2) 65 STG
4186 4252 4317 5047 5113 5178 5808 5874 6604 6669 7249 7314 7379 8010 7076 8141 8871 8936 9466 9532 9598 10228 10293 10358 10988 11104 11734 11799 12429
35 41 47 53 59 65 71 77 83 89 94 100 106 112 118 124 130 136 142 148 154 160 166 172 178 183 189 195 201
8.5
14
2
1
1
1
1
1
10.0 11.5 13.0 14.5 16.0 17.5 19.0 20.5 22.0 23.5 26.0 27.5 29.0 30.5 32.0 33.5 35.0 36.5 38.0 39.5 41.0 42.5 44.0 45.5 47.0 49.5 51.0 52.5 54.0
18 18 18 22 22 22 26 26 30 30 34 34 34 34 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38
3 3 3 4 4 4 5 5 6 6 7 7 7 8 8 8 9 9 10 10 10 11 11 11 12 12 13 13 14
1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4 4 8 8 8 12 12 12 16 16 20 20 24
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1
THRUST LIMIT: 60Hz = 138 stages, 50Hz = 199 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-5
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with E 562 Series SP1000 Pumps.
(TE7000) E0220
E 562 SERIES SP1000 Discharge Assembly 3” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
154 160 166 172 178 183 189 195 201 207 213 219 225 231 237 243 249 255 261 267 272
(2) 77 STG HSS (1) 83 STG + (1) 77 UHSS (2) 83 STG UHSS (1) 89 STG + (1) 83 UHSS (2) 89 STG UHSS (1) 65 STG + (2) 59 UHSS (2) 65 STG + (1) 59 UHSS (3) 65 STG UHSS (1) 71 STG + (2) 65 UHSS (2) 71 STG + (1) 65 UHSS (3) 71 STG UHSS (1) 77 STG + (2) 71 UHSS (2) 77 STG + (1) 71 UHSS (3) 77 STG UHSS (1) 83 STG + (2) 77 UHSS (2) 83 STG + (1) 77 UHSS (3) 83 STG UHSS (1) 89 STG + (2) 83 UHSS (2) 89 STG + (1) 83 UHSS (3) 89 STG UHSS (2) 71 STG + (2) 65 UHSS
STG
STG
STG STG
STG STG
STG STG
STG STG
STG STG
STG
9598
41.0
38
8
10
1
1
1
1
1
10228
42.5
38
12
11
1
1
1
1
1
10293
44.0
38
12
11
1
1
1
1
1
10358
45.5
38
12
11
1
1
1
1
1
10988
47.0
38
16
12
1
1
1
1
1
11104
49.5
38
16
12
1
1
1
1
1
11734
51.0
38
20
13
1
1
1
1
1
11799
52.5
38
20
13
1
1
1
1
1
12429
54.0
38
24
14
1
1
1
1
1
12244
55.5
38
24
14
1
1
1
1
1
12309
57.0
38
24
14
1
1
1
1
1
13040
58.5
38
28
15
1
1
1
1
1
13106
60.0
38
28
15
1
1
1
1
1
13172
61.5
38
28
15
1
1
1
1
1
13702
63.0
38
32
16
1
1
1
1
1
13767
64.5
38
32
16
1
1
1
1
1
14397
66.0
38
36
17
1
1
1
1
1
14462
67.5
38
36
17
1
1
1
1
1
14527
69.0
38
36
17
1
1
1
1
1
15257
70.5
38
40
18
1
1
1
1
1
15372
73.0
38
40
18
1
1
1
1
1
THRUST LIMIT: 60Hz = 188 stages, 50Hz = 270 stages (for Higher Pressures, Floater Pumps may be suitable).
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-7
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ7500) J0240 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2
J0240 CMP 02 STG
3425
2.7
14
1
1
1
1
1
1
6
J0240 CMP 06 STG
3542
4.0
14
1
1
1
1
1
1
9
J0240 CMP 09 STG
3634
5.4
14
1
1
1
1
1
1
12
J0240 CMP 12 STG
3791
6.8
14
2
1
1
1
1
1
15
J0240 CMP 15 STG
3883
8.2
14
2
1
1
1
1
1
19
J0240 CMP 19 STG
3994
9.5
14
2
1
1
1
1
1
22
J0240 CMP 22 STG
4551
10.9
18
3
1
1
1
1
1
25
J0240 CMP 25 STG
4643
12.3
18
3
1
1
1
1
1
29
J0240 CMP 29 STG
4754
13.7
18
3
1
1
1
1
1
32
J0240 CMP 32 STG
5514
15.0
22
4
1
1
1
1
1
35
J0240 CMP 35 STG
5603
16.4
22
4
1
1
1
1
1
39
J0240 CMP 39 STG
6279
17.8
26
5
1
1
1
1
1
42
J0240 CMP 42 STG
6371
19.2
26
5
1
1
1
1
1
45
J0240 CMP 45 STG
6463
20.5
26
5
1
1
1
1
1
48
J0240 CMP 48 STG
7220
21.9
30
6
1
1
1
1
1
50
(2) 25 STG
7436
24.6
30
6
1
1
1
1
1
54
(1) 29 STG + (1) 25 STG
8012
26.0
34
7
1
1
1
1
1
58
(2) 29 STG
8123
27.4
34
7
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8218
28.7
34
7
1
1
1
1
1
64
(2) 32 STG
8878
30.0
38
8
1
1
1
1
1
67
(1) 35 STG + (1) 32 STG
8967
31.4
38
8
1
1
1
1
1
70
(2) 35 STG
9056
32.8
38
8
1
1
1
1
1
74
(1) 39 STG + (1) 35 STG
9832
34.2
38
4
9
1
1
1
1
1
78
(2) 39 STG
9943
35.6
38
4
9
1
1
1
1
1
81
(1) 42 STG + (1) 39 STG
10035
37.0
38
4
9
1
1
1
1
1
84
(2) 42 STG
10592
38.4
38
8
10
1
1
1
1
1
THRUST LIMIT: 60Hz = 83 stages, 50Hz = 119 stages . Consider E0220 pump.
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-8
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ7500) J0240 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
87 90
(1) 45 STG + (1) 42 STG (2) 45 STG
10684 10776
39.7 41.0
38 38
8 8
10 10
1 1
1 1
1 1
1 1
1 1
93 96
(1) 48 STG + (1) 45 STG (2) 48 STG
11433 11525
42.4 43.8
38 38
12 12
11 11
1 1
1 1
1 1
1 1
1 1
99 102
(1) 53 STG + (2) 32 STG (2) 35 STG + (1) 32 STG
12331 12420
46.4 47.8
38 38
16 16
12 12
1 1
1 1
1 1
1
1 1
105 109
(3) 35STG (1) 39 STG + (2) 35 STG
12259 12935
49.2 50.6
38 38
16 20
12 13
1 1
1 1
1 1
1 1
113
(2) 39 STG + (1) 35 STG
13046
52.0
38
20
13
1
1
1
1
117 120
(3) 39STG (1) 42 STG + (2) 39 STG
13157 13814
53.4 54.8
38 38
20 14
13 14
1 1
1 1
1 1
1 1
THRUST LIMIT: 60Hz = 83 stages, 50Hz = 119 stages . Consider E0220 pump.
Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-9
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ9000) J0270 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2
J0270 CMP 02 STG
3425
2.7
14
1
1
1
1
1
1
6
J0270 CMP 06 STG
3543
4.0
14
1
1
1
1
1
1
9
J0270 CMP 09 STG
3636
5.4
14
1
1
1
1
1
1
12
J0270 CMP 12 STG
3793
6.8
14
2
1
1
1
1
1
15
J0270 CMP 15 STG
3886
8.2
14
2
1
1
1
1
1
19
J0270 CMP 19 STG
3998
9.5
14
2
1
1
1
1
1
22
J0270 CMP 22 STG
4555
10.9
18
3
1
1
1
1
1
25
J0270 CMP 25 STG
4648
12.3
18
3
1
1
1
1
1
29
J0270 CMP 29 STG
4760
13.7
18
3
1
1
1
1
1
32
J0270 CMP 32 STG
5520
15.0
22
4
1
1
1
1
1
35
J0270 CMP 35 STG
5610
16.4
22
4
1
1
1
1
1
39
J0270 CMP 39 STG
6287
17.8
26
5
1
1
1
1
1
42
J0270 CMP 42 STG
6379
19.2
26
5
1
1
1
1
1
45
J0270 CMP 45 STG
6472
20.5
26
5
1
1
1
1
1
48
J0270 CMP 48 STG
7230
21.9
30
6
1
1
1
1
1
50
(2) 25 STG
7446
24.6
30
6
1
1
1
1
1
54
(1) 29 STG + (1) 25 STG
8023
26.0
34
7
1
1
1
1
1
58
(2) 29 STG
8135
27.4
34
7
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8230
28.7
34
7
1
1
1
1
1
64
(2) 32 STG
8890
30.0
38
8
1
1
1
1
1
67
(1) 35 STG + (1) 32 STG
8730
31.4
38
8
1
1
1
1
1
70
(2) 35 STG
8820
32.8
38
8
1
1
1
1
1
74
(1) 39 STG + (1) 35 STG
9597
34.2
38
9
1
1
1
1
1
78
(2) 39 STG
9709
35.6
38
4
9
1
1
1
1
1
81
(1) 42 STG + (1) 39 STG
9801
37.0
38
4
9
1
1
1
1
1
84
(2) 42 STG
10358
38.4
38
8
10
1
1
1
1
1
4
87 (1) 45 STG + (1) 42 STG 10451 39.7 38 8 10 1 THRUST LIMIT: 60Hz = 60 stages, 50Hz = 86 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-10
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
1
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with J 700 Series SP1000 Pumps.
J 700 SERIES SP1000
(TJ12000) J0360 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
2 5 8
J0360 CMP 02 STG J0360 CMP 05 STG J0360 CMP 08 STG
3400 3483 3564
2.7 4.0 5.4
14 14 14
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 14
J0360 CMP 11 STG J0360 CMP 14 STG
3712 3795
6.8 8.2
14 14
2 2
1 1
1 1
1 1
1 1
1 1
17 20
J0360 CMP 17 STG J0360 CMP 20 STG
3877 4423
9.5 10.9
14 18
2 3
1 1
1 1
1 1
1 1
1 1
23 26 29
J0360 CMP 23 STG J0360 CMP 26 STG J0360 CMP 29 STG
4506 4589 5337
12.3 13.7 15.0
18 18 22
3 3 4
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
32 35
J0360 CMP 32 STG J0360 CMP 35 STG
5418 6065
16.4 17.8
22 26
4 5
1 1
1 1
1 1
1 1
1
38 41
J0360 CMP 38 STG J0360 CMP 41 STG
6149 6231
19.2 20.5
26 26
5 5
1 1
1 1
1 1
1 1
1 1
44
J0360 CMP 44 STG
6978
21.9
30
6
1
1
1
1
1
46
(2) 23 STG
7162
24.6
30
6
1
1
1
1
1
49 52 55
(1) 26 STG + (1) 23 STG (2) 26 STG (1) 29 STG + (1) 26 STG
7710 7793 7876
26.0 27.4 28.7
34 34 34
7 7 7
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
58
(2) 29 STG
8524
30.0
38
8
1
1
1
1
1
61
(1) 32 STG + (1) 29 STG
8605
31.4
38
8
1
1
1
1
1
64 67
(2) 32 STG (1) 35 STG + (1) 32 STG
8686 9333
32.8 34.2
38 38
8 9
1 1
1 1
1 1
1 1
1 1
4
1
70 (2) 35 STG 9415 35.6 38 4 9 1 1 1 1 1 THRUST LIMIT: 60Hz = 60 stages, 50Hz = 86 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-11
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with M 950 Series SP1000 Pumps.
M 950 SERIES SP1000
(TM19000) M0560 Discharge Assembly 4” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
8 9 10
M0560 CMP A-CUT 08 STG M0560 CMP A-CUT 09 STG M0560 CMP A-CUT 10 STG
4198 4266 4326
6.3 6.9 7.5
14 14 14
2 2 2
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 12
M0560 CMP A-CUT 11 STG M0560 CMP A-CUT 12 STG
4393 4461
8.1 8.7
14 14
2 2
1 1
1 1
1 1
1 1
1 1
13 14
M0560 CMP A-CUT 13 STG M0560 CMP A-CUT 14 STG
4528 5060
9.3 9.9
14 18
2 3
1 1
1 1
1 1
1 1
1 1
15 16 17
M0560 CMP A-CUT 15 STG M0560 CMP A-CUT 16 STG M0560 CMP A-CUT 17 STG
5127 5195 5266
10.6 11.2 11.8
18 18 18
3 3 3
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
18 19
M0560 CMP A-CUT 18 STG M0560 CMP A-CUT 19 STG
5333 5396
12.4 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
20 21
M0560 CMP A-CUT 20 STG M0560 CMP A-CUT 21 STG
5464 6199
13.6 14.2
18 22
3 4
1 1
1 1
1 1
1 1
1
22
M0560 CMP A-CUT 22 STG
6266
14.8
22
4
1
1
1
1
1
23
M0560 CMP A-CUT 23 STG
6331
15.4
22
4
1
1
1
1
1
24 25 26
M0560 CMP A-CUT 24 STG M0560 CMP A-CUT 25 STG M0560 CMP A-CUT 26 STG
6398 6468 6536
16.0 16.6 17.2
22 22 22
4 4 4
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
27
M0560 CMP A-CUT 27 STG
7168
17.8
26
5
1
1
1
1
1
28
M0560 CMP A-CUT 28 STG
7232
18.4
26
5
1
1
1
1
1
29 30
M0560 CMP A-CUT 29 STG M0560 CMP A-CUT 30 STG
7302 7369
19.0 19.6
26 26
5 5
1 1
1 1
1 1
1 1
1 1
1
31 M0560 CMP A-CUT 31 STG 7437 20.2 26 5 1 1 1 1 1 THRUST LIMIT: 60Hz = 21 stages, 50Hz = 31 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-12
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with M 950 Series SP1000 Pumps.
M 950 SERIES SP1000
(TM24000) M0700 Discharge Assembly 6” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
8 9 10
M0700 CMP A-CUT 08 STG M0700 CMP A-CUT 09 STG M0700 CMP A-CUT 10 STG
4198 4266 4326
6.3 6.9 7.5
14 14 14
2 2 2
1 1 1
1 1 1
1 1 1
1 1 1
1 1 1
11 12
M0700 CMP A-CUT 11 STG M0700 CMP A-CUT 12 STG
4393 4461
8.1 8.7
14 14
2 2
1 1
1 1
1 1
1 1
1 1
13 14 15
M0700 CMP A-CUT 13 STG M0700 CMP A-CUT 14 STG M0700 CMP A-CUT 15 STG
4528 5060 5127
9.3 9.9 10.6
14 18 18
2 3 3
1 1 1
1 1 1
1 1 1
1 1 1
1
16 17
M0700 CMP A-CUT 16 STG M0700 CMP A-CUT 17 STG
5195 5266
11.2 11.8
18 18
3 3
1 1
1 1
1 1
1 1
1 1
18 19
M0700 CMP A-CUT 18 STG M0700 CMP A-CUT 19 STG
5333 5396
12.4 13.0
18 18
3 3
1 1
1 1
1 1
1 1
1 1
M0700 CMP A-CUT 20 STG
5464
13.6
18
3
1
1
1
1
1
6199
14.2
22
4
1
1
1
1
1
6266
14.8
22
4
1
1
1
1
1
6331
15.4
22
4
1
1
1
1
1
6398
16.0
22
4
1
1
1
1
1
6468
16.6
22
4
1
1
1
1
1
6536
17.2
22
4
1
1
1
1
1
7168
17.8
26
5
1
1
1
1
1
7232
18.4
26
5
1
1
1
1
1
7302
19.0
26
5
1
1
1
1
1
7369
19.6
26
5
1
1
1
1
1
7437
20.2
26
5
1
1
1
1
1
20 21 22 23 24 25 26 27 28 29 30 31
M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS M0700 HSS
CMP A-CUT 21 STG CMP A-CUT 22 STG CMP A-CUT 23 STG CMP A-CUT 24 STG CMP A-CUT 25 STG CMP A-CUT 26 STG CMP A-CUT 27 STG CMP A-CUT 28 STG CMP A-CUT 29 STG CMP A-CUT 30 STG CMP A-CUT 31 STG
1 1
THRUST LIMIT: 60Hz = 22 stages, 50Hz = 31 stages . Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc.
The ESP Specialists
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
www.woodgroup-esp.com Page-13
Wood Group ESP, Inc. SURFACE PUMPING SYSTEM PRE-SELECTION AND BUILD with N 950 Series SP1000 Pumps.
N 950 SERIES SP1000
(TN35000) N1150 Discharge Assembly 6” Coated Steel
Motor Group
ESP Pump Description Pumps have SS & AR Heads & Bases
1
N1150 CMP A-CUT 1 STG
3786
2.4
14
1
1
1
1
1
1
2
N1150 CMP A-CUT 2 STG
3862
3.0
14
1
1
1
1
1
1
3
N1150 CMP A-CUT 3 STG
3938
3.6
14
1
1
1
1
1
1
4
N1150 CMP A-CUT 4 STG
4014
4.2
14
1
1
1
1
1
1
5
N1150 CMP A-CUT 5 STG
4087
4.7
14
1
1
1
1
1
1
6
N1150 CMP A-CUT 6 STG
4162
5.3
14
1
1
1
1
1
1
7
N1150 CMP A-CUT 7 STG
4303
5.9
14
2
1
1
1
1
1
8
N1150 CMP A-CUT 8 STG
4379
6.5
14
2
1
1
1
1
1
9
N1150 CMP A-CUT 9 STG
4455
7.1
14
2
1
1
1
1
1
10
N1150 CMP A-CUT 10STG
4528
7.6
14
2
1
1
1
1
1
11
N1150 CMP A-CUT 11STG
4604
8.2
14
2
1
1
1
1
1
THRUST LIMIT: 60Hz = 8 stages, 50Hz = 11 stages. Selections listed are a guide only, for confirmation contact WG ESP.
Wood Group ESP, Inc. Page-14
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Surface Pumping Systems - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc.
WELLHEAD EQUIPMENT WELLHEADS HHS - COMPLETE UNIT CSG O.D. TBG 4 1/2 5 1/2 7
8 5/8
9 5/8
10 3/4
13 3/8
PART NUMBER EUE 2 3/8 2 7/8 2 3/8 2 7/8 2 3/8 2 7/8 3 1/2 2 3/8 2 7/8 3 1/2 4 1/2 2 3/8 2 7/8 3 1/2 4 1/2 5 1/2 2 7/8 4 1/2 5 1/2 7 6 7 6 5/8
#1 RND
#1 FLAT
#2 RND
741261 741263 741234 741241
741243
741233 741240 741244 721247
#2 FLAT
#4 RND
#4 FLAT
#6 RND
#6 FLAT
#8 RND
741205 741211 741217 741223 741229 741237 741242
741202 741208 741214 741220 741226 741232 741239 741245
741204 741210 741216 741222 741228 741236 741284
741201 741207 741213 741219 741225 741231 741238
741203 741209 741215 741221 741227 741235
741200 741206 741212 741218 741224 741230
741256
741246
741248 741257 741458
741482
741259 741260 741251
741249 741250
741529 741455
741798
741252 741255 741253 741254 741262 741283 741285
Wood Group ESP, Inc.
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Page 1
Wood Group ESP, Inc. WELLHEAD EQUIPMENT WELLHEADS HHS - TOP PLATE CSG O.D. TBG
PART NUMBER EUE 2 3/8 2 7/8 2 3/8 2 7/8 2 3/8 2 7/8 3 1/2 2 7/8 4 1/2 2 3/8 2 7/8 3 1/2 4 1/2 4 1/2 6 6 5/8 7
4 1/2 5 1/2 7 8 5/8
9 5/8 10 3/4 13 3/8
#1 RND
#1 FLAT
#2 RND
741377 741410 741410 741410
741422
#2 FLAT
#4 RND
#4 FLAT
#6 RND
#6 FLAT
#8 RND
741377 741395 741377 741395 741377 741395 741410
741368 741386 741368 741386 741368 741386
741374 741392 741374 741392 741374 741392 741472
741365 741383 741365 741383 741365 741383
741371 741389 741371 741389 741371 741389
741362 741380 741362 741380 741362 741380
741416 741474 741434 741437
741440 741444
741419 741467 741467 741453
PLATE WELLHEADS HHS - BOTTOM CSG O.D. TBG 4 1/2 5 1/2 7 8 5/8 9 5/8
10 3/4 13 3/8
PART NUMBER EUE 2 3/8 2 7/8 2 3/8 2 7/8 2 3/8 2 7/8 3 1/2 2 7/8 4 1/2 2 3/8 2 7/8 3 1/2 4 1/2 4 1/2 6 6 5/8 7
#1 RND
#1 FLAT
#2 FLAT
#4 RND
#4 FLAT
#6 RND
#6 FLAT
#8 RND
741420 741402
741375 741393 741375 741393 741375 741393 741408
741366 741384 741366 741384 741366 741384 741399
741372 741390 741372 741390 741372 741390 741470
741363 741381 741363 741381 741363 741381 741396 741414
741369 741387 741369 741387 741369 741387
741360 741378 741360 741378 741360 741378
741375 741408 741423 741405
741408 741408
741426 741459 741448
741432 741435 741417 741465
741438 741442
741449
741451 741465
Wood Group ESP, Inc. Page-2
#2 RND
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. WELLHEAD EQUIPMENT WELLHEADS HHS - PACKOFF RUBBERS CSG O.D. TBG 4 1/2 5 1/2 7 8 5/8
9 5/8 10 3/4
13 3/8
PART NUMBER EUE 2 3/8 2 7/8 2 3/8 2 7/8 2 3/8 2 7/8 3 1/2 2 7/8 4 1/2 2 3/8 2 7/8 3 1/2 4 1/2 4 1/2 7 6 6 5/8 7
#1 RND
#1 FLAT
#2 RND
741359 741412 741424 741266
741412 741412
741421
#2 FLAT
#4 RND
#4 FLAT
#6 RND
741376 741394 741376 741394 741376 741394 741409
741367 741385 741367 741385 741367 741385
741373 741391 741373 741391 741373 741391 741471
741364 741382 741364 741382 741364 741382
#6 FLAT
#8 RND 741361 741379 741361 741379 741361 741379
741388 741388 741388
741415 741473 741433 741436
741439 741443
741418 741800 741466 741452 741466
GLAND WELLHEAD HHS - BODY - SLIPS - PACKING CSG O.D BODY 4 1/2 5 1/2 7 8 5/8 9 5/8 10 3/4 13 3/8
SLIPS PART NUMBER PART NUMBER 741350 741351 741352 741353 741354 741355 741469
2 3/8
2 7/8
3 1/2
4 1/2
741300 741300 741300
741301 741301 741301 741430 741441
741302
741429
741308
741303
741304
5 1/2
6
6 5/8
741305
741450
7
741464
PACKING GLAND PART NUMBER 741340 741340 741340 741342 741341 741341 741468
HHS SPECIFICATIONS TYPE
CASING SIZE O.D. (Inches)
TUBING SIZE O.D. (Inches)
HHS HHS HHS HHS HHS HHS HHS HHS HHS
4 1/2, 5 1/2, 7 4 1/2, 5 1/2, 7 7 8 5/8 8 5/8 8 5/8 9 5/8, 10 3/4 9 5/8, 10 3/4 9 5/8, 10 3/4
2 3/8 2 7/8 3 1/2 2 3/8, 3 1/2 4 1/2 5 1/2 2 3/8, 3 1/2 4 1/2 5 1/2
Wood Group ESP, Inc.
RECOMMENDED MAX LOAD Lbs 80,000 80,000 80,000 100,000 100,000 100,000 100,000 100,000 100,000
The ESP Specialists
Kgs 36,000 36,000 36,000 45,000 45,000 45,000 45,000 45,000 45,000
MAXIMUM SETTING DEPTH (Safety Factor = 2.0) Ft. M. 10,000 3,048 7,100 2,165 4,900 1,495 4,900 1,495 3,200 975 2,600 790 4,900 1,495 3,200 975 2,600 790
WEIGHT Lbs 144 144 148 186 186 186 226 226 226
Kgs 66 66 68 85 85 85 103 103 103
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Page 3
Wood Group ESP, Inc. Bolt On Head
Couplings between Units Couplings are shipped at the top of each unit except for the coupling adapter at the bottom of the seal and the pump to intake (or GS) that must be ordered separately. All coupling splines are SAE 6 tooth, unless noted as INV (Involute). Coupling
Pump
TA/TR3 919415 (3/8 ) 914341 (5/8)
Pump
Pump To Pump
934182 (11/16) Cprsn
120556 (11/16)
Intake or Gas Separator
TE/TR5/E56
TH/TR5
TJ/TR7 TM/TR7
TN
1008556 (1/2) 926477 (5/8)
934026 (7/8)
934182 (11/16)
1011709 (1)
120557 (7/8) 123270 (1)
934026 (7/8) Cprsn
123270 (1)
Cprsn
952572 (1-3/16)
952572 (1-3/16)
1032770 (1-1/2)
952572 (1-3/16)
1032770 (1-1/2)
952572
120555 (5/8)
120557 (7/8)
120556 (11/16)
123270 (1)
(1-3/16)
120557 (7/8)
Pump To Intake or GS
Seal
919605 (3/8 to 11/16) 912022 (5/8 to 11/16) 934182 (11/16)
Intake or GS To Seal
Motor
TG/TR5
120554 (1/2) 120555 (5/8)
Seal
TD/TR387/TR4
912071 (11/16 to 3/4)
Seal to Seal
926956 (3/4)
Coupling Adapter
1046754 (3/4 to 1-3/16)
Seal To Motor (Sgl or UT) or BOH
1042043 (7/8 to 1-3/16)
934281 5/8”- 7/8” 934232 (11/16 to 7/8) 934026 (7/8)
934026 (7/8)
949388 (7/8 to 1-3/16)
949388 (7/8 to 1-3/16) 949651 (1 to 1-3/16)
123247 (1-3/16) 949651 1”- 1 3/16”
944512
949651 (1 to 1-3/16)
123247
(1 3/16) Unit Adptr & Cplg 740211 (7/8)
952572 (1 3/16)
(1-3/16) 943829 (1-3/16) 151409 (1-3/16 HL)
151407 (1-3/16 pre-shimmed) 1002575 (7/8 to 1-1/2) Type 62 & 92 1000124 (1-1/8 to 1- 1/2) Type 92 HTI 120697 (1-1/8 to 1-1/2) Inv
945592 (1-3/16 to 2) Type 62 SGL: 947986 (2 to 1-3/16) Type 62 & 92 UT: 948042 (2 to 1- 3/8) Type 92HTI: 121437 (2 to 1-3/8) Inv
960765 (1-3/16 to 1-1/2) 960245 (1-1/2) 960641 (1-1/2 to 2-1/4) 960294 (2-1/4 to (1- 1/2)
Type 62: 933523 (1) Type 92: 110716 (1-1/8)
Motor
Motor To Motor (CT or LT)
Type 92: 1017623 (1-3/8) 914259 (11/16)
Type 92 HTI 120696 (1-1/8) Inv Type 62 to 92 120862 (1 to 1-1/8)
Motor Base or Sensor
Type 92 HTI to 92 Std: 141712 (1-3/8 inv to 1-3/8)
961961 (1-1/2)
Type 92HTI: 121784 (1-3/8) Inv Type 92-62: 141710 (1-3/16 to 1-3/8)
Type 92 - 62 120787 (1-1/8 to 1)
Wood Group ESP, Inc. Page-4
Type 62: 944165 (1-3/16)
The ESP Specialists
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT CHECK VALVES AND BLEEDER VALVES DESCRIPTION
Lbs.
CHECK VALVES -up to 2200 psi CHECK VALVE 2 3/8” - 8rd 2200 CHECK VALVE 2 3/8” - 8rd 2200 SST CHECK VALVE 2 7/8” - 8rd 2200 CHECK VALVE 2 7/8” - 8rd 2200 SST CHECK VALVE 3 1/2” - 8rd 2200 CHECK VALVE 3 1/2” - 8rd 2200 SST CHECK VALVES -up to 5000 psi CHECK VALVE 2 3/8” - 8rd 5000 CHECK VALVE 2 3/8” - 8rd 5000 SST CHECK VALVE 2 7/8” - 8rd 5000 CHECK VALVE 2 7/8” - 8rd 5000 SST CHECK VALVE 3 1/2” - 8rd 5000 CHECK VALVE 3 1/2” - 8rd 5000 SST BLEEDER VALVES BLEEDER VALVE 2 3/8” - 8rd BLEEDER VALVE 2 7/8” - 8rd BLEEDER VALVE 3 1/2” - 8rd CASING CHECK & BLEEDER VALVE 4 1/2” - 8rd CASING CHECK & BLEEDER VALVE 5 1/2” - 8rd CASING CHECK & BLEEDER VALVE 7” - 8rd
WEIGHT Kgs.
PART NUMBER
6 6 10 10 16 16
2.72 2.72 4.54 4.54 7.26 7.26
913939 120169 925206 120168 926386 143565
9 9 15 15 24 24
4.08 4.08 6.80 6.80 10.89 10.89
145935 145936 143316 143317 145937 143327
6 10 16
2.72 4.54 7.26
912501 925339 926394 127400 127402 127403
BREAK OFF PLUGS BRASS 2”, 2 3/8”, 2 7/8”, and 3 1/2” MONEL 2”, 2 3/8”, 2 7/8”, and 3 1/2”
0.30 0.30
0.14 0.14
911966 925354
REDUCING NIPPLES 2 3/8” OD 8rd x 2 7/8” OD 8rd 2 3/8” OD 8rd x 3 1/2” OD 8rd 2 7/8” OD 8rd x 3 1/2” OD 8rd
2.5 7.5 7.5
1.13 3.40 3.40
917567 917575 917583
SHIPPING BOXES w/o Hinges EQUIPMENT INSIDE
DIA
Type 300-700 Series
7”
Type 300-900 Series
12”
Wood Group ESP, Inc.
Feet 6 7.5 12.5 15.5 18.5 23 26 28.5 32 36 7.5 12 15 23 26 34
LENGTH Meters 1.8 2.3 3.8 4.7 5.6 7.0 7.9 8.7 9.8 11.0 2.3 3.7 4.6 7.0 7.9 10.4
The ESP Specialists
WEIGHT Lbs. Kgs 146 66.2 188 85.3 351 159.2 435 197.3 500 226.8 621 281.7 750 340.2 810 367.4 926 420.0 1042 472.7 310 140.6 495 224.5 619 280.8 949 430.5 1073 486.7 1403 636.4
PART NUMBER 741111 741121 741112 741113 741114 741115 741116 741117 741118 741119 741124 741120 741127 741125 741126 741128
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Page 5
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT MONEL HARDWARE KITS SERIES
PUMP INTAKE GAS SEPARATOR SEAL MOTOR (SINGLE) MOTOR (UT) MOTOR (CT) MOTOR (LT) SENSOR- PRESS & TEMP SENSOR - PRESSURE ONLY BOLT-ON-BASE
TR3 1054519 1054519 1054519 1054527 1054535 1054543 1054550 1054568 1054576 1055078 1055078
TR4 1054519 1054519 1054519 1054584 1054592 1054600 1054618 1054626 1054683 1055086 1055086
TR5 1054691 1054691 1054691 1054709 1054717 1054725 1054733 1054741 1054758 1055094 1055094
TR6 1054766 1054766
TR7
TR8 1054774 1054774
1054782 1054790 1054808 1059162 1054816 1054824 1055102 1055102
1054782
Notes: 1. Monel bolts and washers are supplied as standard with all downhole equipment. Above monel hardware kits are available to replace or upgrade equipment and includes all bolts, washers, plugs and drain and fill components. These components may also be purchased as individual parts from any Wood Group ESP, Inc. facility. Contact your sales or service representative for individual part prices. 2. Monel bolts and washers are recommended for use with all components having a corrosion resistant coating. 3. Screws and lock washers are for the top end connection of the listed equipment. 4. O-rings are not provided in the kits.
MONEL HARDWARE KITS
DESCRIPTION FLAME SPRAY COATING METAL FLAME SPRAY COATING - TOUCH-UP KIT
Wood Group ESP, Inc. Page-6
The ESP Specialists
PART NUMBER APP-83 922872
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT MOTOR OIL DESCRIPTION ROCON #2 MEDIUM - 5 GALLON CAN ROCON #3 (SYNTHETIC) - 5 GALLON CAN ROCON #220 (SYNTHETIC - HI-TEMP) - 55 GALLON CAN
WEIGHT Lbs. Kgs. 25 11.3 37 16.8 462 209.6
OIL FILLING COMPONENTS OIL CAN COMPLETE WITH PUMP, HOSE. ETC PUMP PUMP HOSE SWEDGELOK - FEMALE PRESSURE GAGE ALEMITE ADAPTER CAN, 5 GALLON WITH SEAL PIPE, 19” X .500 BLACK PIPE ELBOW 1/2” PIPE NIPPLE 1/2” X 1 1/2” PIPE REDUCER PIPE TEE SCREW, HEX HEAD 5/16” X 3/4” PLATE, STEEL PUMP HANDLE INSTALLATION CLAMPS TR3 MOTOR SHOULDER CLAMP TA PUMP SHOULDER CLAMP TA PUMP FRICTION CLAMP TR3 SEAL FRICTION CLAMP TR387 PUMP FRICTION CLAMP TR4 MOTOR SHOULDER CLAMP TD PUMP SHOULDER CLAMP TD PUMP FRICTION CLAMP TR5 MOTOR CLAMP TG PUMP FRICTION CLAMP TH PUMP FRICTION CLAMP TJ PUMP SHOULDER CLAMP TR7 MOTOR CLAMP TR7 SEAL FRICTION CLAMP TM PUMP SHOULDER CLAMP TM PUMP FRICTION CLAMP TN PUMP FRICTION CLAMP
Wood Group ESP, Inc.
The ESP Specialists
16
7.3
0.60
0.27
24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24
10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89 10.89
PART NUMBER 985978 2643022 127295
1059270 1059288 1059296 1059304 1059320 1059338 1059714 127063 127064 127065 127066 127067 127068 127069 127070
T111 T110 T2345 T2346 T2166 T478 T479 T328 T480 T185 T2344 T504 T772 T2292 T484 T773 T2287
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Page 7
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT ADAPTER KITS
DESCRIPTION TD PUMP (.875” SHAFT) TO TR5 INTAKE OR RGS TD PUMP (.687” SHAFT) TO TR5 INTAKE OR RGS TD PUMP (.625” SHAFT) TO TR5 INTAKE OR RGS TD INTAKE OR RGS TO TR5 SEAL TJ / TM / TN INTAKE TO TR5 SEAL TR7 SEAL TO TR5 MOTOR TR7 SEAL TO TR7 SEAL TR4 SEAL TO TR4 SEAL
PART NUMBER 740220 740226 740235 740218 740225 740237 740238 740211
ADAPTER KITS COMPONENT PARTS
TD INTAKE OR RGS TO TR5 SEAL - BODY TD INTAKE OR RGS TO TR5 SEAL - COUPLING TD PUMP (.875” SHAFT) TO TR5 INTAKE OR RGS - BODY TD PUMP (.875” SHAFT) TO TR5 INTAKE OR RGS - COUPLING TD PUMP (.687” SHAFT) TO TR5 INTAKE OR RGS - BODY TD PUMP (.687” SHAFT) TO TR5 INTAKE OR RGS - COUPLING TD PUMP (.625” SHAFT) TO TR5 INTAKE OR RGS - BODY TD PUMP (.625” SHAFT) TO TR5 INTAKE OR RGS - COUPLING TD INTAKE OR RGS TO TR5 SEAL - BODY TD INTAKE OR RGS TO TR5 SEAL - COUPLING TJ / TM / TN INTAKE TO TR5 SEAL - BODY TJ / TM / TN INTAKE TO TR5 SEAL - COUPLING TR7 SEAL TO TR5 MOTOR - BODY TR7 SEAL TO TR5 MOTOR - COUPLING TR7 SEAL TO TR7 SEAL - BODY TR7 SEAL TO TR7 SEAL - COUPLING TR4 SEAL TO TR4 SEAL - BODY TR4 SEAL TO TR4 SEAL - COUPLING
Wood Group ESP, Inc. Page-8
The ESP Specialists
1010099 943803 1010099 1000454 1010099 1000447
740266 9601112 132718 960641 740250 740252
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT SEAL TO INTAKE ADAPTORS DESCRIPTION 338 CL .750 X 338 ESP BOI OR RGS .687 338 CL .750 X 338 ESP BOI OR RGS .875 338 CL .750 X 55 ODI PUMP RPS .687 338 CL .750 X 55 ODI RGS .875 400 CL .875 X 400 ESP BOI OR RGS .875 400 CL .875 X 55 ODI PUMP RPS .688 400 CL .875 X 55 ODI PUMP RPSLA 1.00 400 CL .875 X 55 ODI RGS .875 400 CL .875 X 540 ESP BOI OR RGS 1.187 400 CL .875 X 70 ODI PUMP KPS .875 400 CL .875 X 70 ODI PUMP KPSLA 1.250 400 CL .875 X 70 ODI RGS 1.125 513 CL 1.00 X 55 ODI PUMP RPS .688 513 CL 1.00 X 55 ODI PUMP RPSLA 1.00 513 CL 1.00 X 55 ODI RGS .875 513 CL 1.00 X 400 ESP BOI OR RGS .875 513 CL 1.00 X 70 ODI PUMP KPS .875 513 CL 1.00 X 70 ODI PUMP KPSLA 1.250 513 CL 1.00 X 70 ODI RGS 1.125 513 CL 1.00 X 540 ESP BOI OR RGS 1.187
734 735 736 737 700 701 702 703 738 739 750 751 710 711 712 713 714 715 716 717
338/375 ESP .750 X 338 CL PUMP OR RGS .625 338/375 ESP .750 X 338 CL PUMP OR RGS .687 338/375 ESP .750 X 400 CL PUMP .687 338/375 ESP .750 X 400 CL HV PMP / RGS .875 338/375 ESP .750 X 55 ODI PUMP RPS .688 338/375 ESP .750 X 55 ODI PUMP RPSLA 1.00 338/375 ESP .750 X 55 ODI RGS .875 400 ESP .875 X 338 CL PUMP OR RGS .625 400 ESP .875 X 338 CL PUMP OR RGS .687 400 ESP .875 X 400 CL PUMP .687 400 ESP .875 X 55 ODI PUMP RPS .688 400 ESP .875 X 55 ODI PUMP RPSLA 1.00 400 ESP .875 X 55 ODI RGS .875 400 ESP .875 X 513 CL BOI OR RGS .875 400 ESP .875 X 70 ODI PUMP KPS .875 400 ESP .875 X 70 ODI PUMP KPSLA 1.25 400 ESP .875 X 70 ODI RGS 1.125 400 ESP .875 X 540 ESP BOI OR RGS 1.187 400 ESP .875 X 400 CL HV PUMP/RGS .875 540 ESP 1.187 X 400 CL PUMP .687 540 ESP 1.187 X 55 ODI PUMP RPS .688 540 ESP 1.187 X 55 ODI PUMP RPSLA 1.00 540 ESP 1.187 X 55 ODI RGS .875 540 ESP 1.187 X 513 CL BOI OR RGS .875 540 ESP 1.187 X 70 ODI PUMP KPS .875 540 ESP 1.187 X 70 ODI PUMP KPSLA 1.250 540 ESP 1.187 X 70 ODI RGS 1.125 540 ESP 1.187 X 400 ESP BOI OR RGS .875 540 ESP 1.187 X 400 CL HV PMP/RGS .875 540 ESP 1.187 X 562 CL PUMP 1.187
758 759 760 761 762 763 764 765 766 704 705 706 707 768 769 770 771 772 799 718 719 720 721 722 723 724 725 740 773 774
Wood Group ESP, Inc.
The ESP Specialists
PART NUMBER 734SS 734XX 735SS 735XX 736SS 736XX 737SS 737XX 700SS 700XX 701SS 701XX 702SS 702XX 703SS 703XX 738SS 738XX 739SS 739XX 750SS 750XX 751SS 751XX 710SS 710XX 711SS 711XX 712SS 712XX 713SS 713XX 714SS 714XX 715SS 715XX 716SS 716XX 717SS 717XX 758SS 759SS 760SS 761SS 762SS 763SS 764SS 765SS 766SS 704SS 705SS 706SS 707SS 768SS 769SS 770SS 771SS 772SS 799SS 718SS 719SS 720SS 721SS 722SS 723SS 724SS 725SS 740SS 773SS 774SS
758XX 759XX 760XX 761XX 762XX 763XX 764XX 765XX 766XX 704XX 705XX 706XX 707XX 768XX 769XX 770XX 771XX 772XX 799XX 718XX 719XX 720XX 721XX 722XX 723XX 724XX 725XX 740XX 773XX 774XX
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Page 9
Wood Group ESP, Inc. MISCELLANEOUS EQUIPMENT SEAL TO INTAKE ADAPTORS DESCRIPTION 55 ODI .875 X 338 CL PUMP OR RGS .625 55 ODI .875 X 338 CL PUMP OR RGS .687 55 ODI .875 X 400 CL HV PMP / RGS .875 55 ODI .875 X 513 CL BOI OR RGS .875 55 ODI .875 X 562 CL PUMP 1.187 55 ODI .875 X 400 ESP BOI OR RGS .875 55 ODI .875 X 400 CL PUMP .687 55 ODI .875 X 540 ESP BOI OR RGS 1.187 70 ODI KTE 1.00 X 400 CL PUMP .687 70 ODI KTE 1.00 X 400 ESP BOI OR RGS .875 70 ODI KTE 1.00 X 513 CL BOI OR RGS .875 70 ODI KTE 1.00 X 540 ESP BOI OR RGS 1.187 70 ODI KTE 1.00 X 400 CL HV PMP / RGS .875 70 ODI KTE 1.00 X 562 CL PUMP 1.187 70 ODI KETM 1.125 X 400 CL PUMP .687 70 ODI KETM 1.125 X 400 ESP BOI OR RGS .875 70 ODI KETM 1.125 X 513 CL BOI OR RGS .875 70 ODI KETM 1.125 X 540 ESP BOI / RGS 1.187 70 ODI KETM 1.125 X 400 CL HV PMP/RGS .875 70 ODI KETM 1.125 X 562 CL PUMP 1.187
785 786 787 788 789 708 709 790 726 727 728 729 791 792 730 731 732 733 795 796
785SS 786SS 787SS 788SS 789SS 708SS 709SS 790SS 726SS 727SS 728SS 729SS 791SS 792SS 730SS 731SS 732SS 733SS 795SS 796SS
785XX 786XX 787XX 788XX 789XX 708XX 709XX 790XX 726XX 727XX 728XX 729XX 791XX 792XX 730XX 731XX 732XX 733XX 795XX 796XX
MOTOR TO SEAL ADAPTORS 375 CL X 325 / 375 ESP .75 450 CL 1.00 X 400 ESP .875 450 CL 1.00 X 540 ESP 1.187 450 CL 1.00 X 55 ODI .875 450 CL 1.00 X 70 ODI 1.125 544 CL 1.125 X 540 ESP 1.187 544 CL 1.125 X 70 ODI 1.125 562 CL 1.250 X 540 1.187 562 CL 1.250 X 70 ODI 1.125 375 ESP X 338 CL .750 456 ESP 1.125 X 400 CL .875 456 ESP 1.125 X 513 CL 1.00 456 ESP 1.125 X 55 ODI .875 456 ESP 1.125 X 70 ODI 1.125 456 ESP 1.187 X 400 CL .875 456 ESP 1.187 X 513 CL 1.00 456 ESP 1.187 X 55 ODI .875 456 ESP 1.187 X 70 ODI 1.125 540 ESP 1.187 X 513 CL 1.00 540 ESP 1.187 X 70 ODI 1.125 540 ESP 1.375 X 513 CL 1.00 540 ESP 1.375 X 70 ODI 1.125 55 ODI 1.00 X 400 CL .875 55 ODI 1.00 X 513 CL 1.00 55 ODI 1.00 X 400 ESP .875 55 ODI 1.00 X 540 ESP 1.187
798 800 801 802 803 804 805 806 807 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825
798SS 800SS 801SS 802SS 803SS 804SS 805SS 806SS 807SS 809SS 810SS 811SS 812SS 813SS 814SS 815SS 816SS 817SS 818SS 819SS 820SS 821SS 822SS 823SS 824SS 825SS
798XX 800XX
70 ODI 1.312 X 513 CL 1.00 70 ODI 1.312 X 540 ESP 1.187
826 827
826SS 827SS
Wood Group ESP, Inc. Page-10
The ESP Specialists
PART NUMBER
806XX
824XX
827XX
www.woodgroup-esp.com
Product Catalog - Wellheads / Miscellaneous Equipment - Copyright Wood Group ESP, Inc. - October, 2009
Wood Group ESP, INC.
Date: Company: Well Name: Reservoir: Field Name: Location: Analyst:
Sandstone
Limestone
Comments
Well Data MD
TVD
(ft | m)
(ft | m)
OD
Weight
Grade
(in | mm) (lb/ft | kg/m)
ConID Drift nection (in | mm) (in | mm)
Casing Liner Liner Open Hole Top Prod. Interval Base Prod. Interval PBTD Tubing Tubing Datum MD: Datum TVD: Deviation Survey MD TVD ( ft | m )
( ft | m )
Datum Temperature: Wellhead temperature:
ft | m ft | m
°F | °C °F | °C
Angle
DLS
MD
TVD
Angle
DLS
( deg )
( °/100' | 90m )
( ft | m )
( ft | m )
( deg )
( °/100' | 90m )
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 1
Wood Group ESP, INC.
Shaft HP Limitations These charts are intended as general guidelines only. Refer to Technical Bulletins or Application Briefs for most recent detailed information. (For more information, contact your Wood Group ESP representative.) HIGH STRENGTH
STANDARD MATERIAL
COMPONENT MOTORS
4130
4130 HS
MONEL K-500
SEALS
OR
INCONEL 718
NITRONIC 50
GAS NITRONIC 50 HS SEPARATORS OR
INCONEL 718 HS
INCONEL 718
INCONEL 718 HS
INCONEL 718
INCONEL 718 HS
MONEL K-500
PUMPS
ULTRA HIGH STRENGTH
NITRONIC 50
SHAFT DIA
MAT’L
0.984”
4130 STEEL 4130 HS STEEL 4130 STEEL 4130 HS STEEL 4130 STEEL 4130 HS STEEL 4130 STEEL 4130 HS STEEL 4130 HS STEEL 4130 HS STEEL
TR-3 UT TR-3 CT TR-3 UT HTI TR-3 CT HTI TR3-UT-HTI-HP TR3-CT-HTI-HP
E37 HSS
TR-5/E56 STD TR-5/E56 HSS
HP @ 60 HZ 121 149 81 109 100 120 60 80 162 122
HP @ 50 HZ
100 124 67 91 83 100 50 67 136 103
0.984”
4130 HS STEEL
270
225
1.181”
4130 STEEL 4130 HS STEEL
490 662
408 550
4130 STEEL 1.377” 4130 HS STEEL TABLE 2 – MOTORS
775 1050
645 870
HP @ 60 HZ 125 200
HP @ 50 HZ 104 167
INCONEL-718 HS
256 410 522
213 342 435
NITRONIC-50 HS
637
531
TR-4 STD TR-4 HSS
SERIES
SHAFT DIA
TR-3 STD TR-3 HSS
0.687”
TR-387/TR-4 STD TR-387/TR-4 HSS TR-4 UHSS
0.875”
TR-5 / TR-538 / TR-675 STD TR-5 / TR-538 / TR-675 HSS
1.188”
MATERIAL NITRONIC-50 HS
INCONEL 718 NITRONIC-50 HS
INCONEL 718
INCONEL 718
1019
849
TABLE 3 – GAS SEPARATORS SERIES TA STD TA HSS TR-387 / TD STD TD HSS TD UHSS TE/TG/TH/TJ/TM STD TE/TG/TH/TJ/TM HSS
SHAFT DIA
MATERIAL
0.687”
NITRONIC-50 HS INCONEL 718
0.875”
NITRONIC-50 HS INCONEL 718
1.188”
NITRONIC-50 HS INCONEL 718
INCONEL-718 HS
TE/TG/TH/TJ/TM UHSS
TN STD
INCONEL-718 HS
1.5”
NITRONIC-50 HS
TABLE 4 – INTAKES
SHAFT DIA
TR-3 HSS TR-4 STD TR-4 HSS TR-4 UHSS TR-5 STD
0.875”
1.188”
TR-5 HSS TR-5 AR
1.375” (Has a
TR-5 AR HSS
1.188” spline)
TR-562 STD
1.375”
TR-562 HSS
TR-7 STD
1.500”
TR-7 HSS TR-950 STD
2.000”
TR-950 HSS
HP @ 50 HZ
MONEL / NITRONIC
160
133
INCONEL 718
256
213
MONEL / NITRONIC INCONEL 718
256
213
INCONEL 718 HS
410 522
342 435
MONEL / NITRONIC INCONEL 718
637
531
1019
849
MONEL / NITRONIC INCONEL 718
637
531
INCONEL 718 HS
1019 1340
849 1100
MONEL / NITRONIC INCONEL 718
690
575
1100
917
MONEL / NITRONIC INCONEL 718 MONEL / NITRONIC INCONEL 718
1000
833
1600
1333
2100
1750
3375
2813
TABLE 5 – SEALS SERIES TD – STD
TA/TD – STD
TE/TH/TJ/TM STD
256 410 522
213 342 435
TM STD
637 1019 1350
531 849 1125
TE/TH/TJ/TM HSS
58
0.625”
94
78
150
125
125
104
200 255
167 212
0.687”
MONEL / NITRONIC INCONEL 718 INCONEL 718 HS
0.875”
MONEL / NITRONIC INCONEL 718 INCONEL 718 HS
1.000”
MONEL K500 INCONEL 718 INCONEL 718 HS
1.188”
MONEL / NITRONIC INCONEL 718 INCONEL 718 HS
1.375”
MONEL / NITRONIC INCONEL 718 INCONEL 718 HS
TN STD TN HSS TN UHSS
70
MONEL / NITRONIC INCONEL 718
TE/TH/TJ/TM UHSS
TM HSS TM UHSS
37
MONEL / NITRONIC INCONEL 718
TD/TG/TE - STD
TG/TE/TH- STD TG/TE/TH - HSS TG/TE/TH - UHSS
44
0.500”
TA/TD - STD
TD/TG/TE - HSS TD/TG/TE - UHSS
HP @ 50 HZ
MAT’L
TA/TD – HSS
TA/TD – HSS TA/TD – UHSS
HP @ 60 HZ
SHAFT DIA
TD – HSS
HP @ 50 HZ 104 167
833
HP @ 60 HZ
0.750”
HP @ 60 HZ 125 200
1000
MAT’L
TR-3 STD
TR-5 AR UHSS
TABLE 1 SERIES
SERIES
1.500”
MONEL / NITRONIC INCONEL 718 INCONEL 718 HS
256
213
410 522
342 435
375 600 765
312 500 638
637
531
1019 1300
849 1083
760
633
1216 1550
1013 1290
1000
833
1600 2040
1333 1700
TABLE 6 – PUMPS
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 2
Wood Group ESP, INC.
ENGINEERING TABLES Pumps 50 Hz 2917 RPM
Model
Series
TA-400 TA-550 TA-900 TA-1200 TA-1500 TA-2200
338
TD-150 TD-300 TD-460 TD-650 TD-850 TD-1250 TD-1750 TD-2200 TD-3000 TD-4300 TD-6000
400
TG-4000
513
Const.
O.D. MM
85.85
101.60
130.30
Stage
Flt.
Cprsn.
Pancake
X X X X X X
X X X X X
X X X X X
X X X X X X X X X X X
X X X X X X X X X X X
X X X X X X X X
Mixed Flow
Recommended Operating Range 3 M /Day
Maximum Downthrust Per Stage Cprsn. Pump Lbs.
BHP per Stage
S/O Head Per Stage Meters
Housing Pressure Limit PSI Hi. Std. Pr.
15.1 15.7 15.8 15.5 16.0
0.07 0.08 0.10 0.12 0.18 0.19
5.0 4.8 4.6 4.4 4.0 4.2
6000
6000
X
40-72 53-93 87-140 120-200 132-265 166-364
17.0 18.4 22.2 20.2 21.0 30.1 11.0 12.4 11.9 15.6 18.8
0.05 0.06 0.08 0.13 0.18 0.30 0.22 0.36 0.37 0.58 0.82
5.0 5.1 5.9 7.0 6.9 7.4 6.2 7.0 5.9 5.9 6.2
5000
6000
X X X X X
11-37 26-60 40-79 60-106 73-135 106-199 159-278 185-371 265-490 397-689 464-994
X
X
424-636
29.5
0.90
11.4
5000
6000
X X X X X X X X
X X X X X X X X
106-298 199-437 291-596 344-649 464-967 530-1285 530-1285 1060-1855
34.7 36.8 41.4 64.6 35.4 25.7 25.7 49.3
0.79 0.90 1.59 1.78 1.63 1.99 1.99 2.55
15.2 14.8 15.9 14.4 13.1 13.5 13.3 10.6
6000
6000
X X X X X X
TE-1500 TE-2700 TE-3300 TE-4200 TE-5500 TE-7000 TE-7200 TE-11000
538
135.65
TH-15000 TH-20000
562
142.75
X X
X X
1325-2517 1987-3113
49.3 70.1
5.27 6.77
14.8 15.5
3000
3600
TJ-7500 TJ-9000 TJ-12000 TJ-20000
675
171.45
X X X X
X X X X
662-1457 662-1722 994-2385 1590-3445
59.0 81.9 100.0 132.0
3.41 5.09 6.60 7.31
17.0 24.8 22.0 21.4
3000
3600
X X X
X X X
1855-3180 1722-3047 1656-2981
232.6 194.7 158.3
11.28 8.33 7.24
31.1 26.0 21.2
X
X
1855-4239
229.2
17.36
31.3
2000
2400
X X X
X X X
2650-3842 2583-3776 1855-4504
193.5 154.9 253.5
16.38 11.92 20.41
26.5 21.2 35.1
X X X
X X X
4107-5962 3710-5697 3378-5167
642.4 534.8 448.1
34.08 25.52 19.82
45.5 37.9 31.8
2300
2760
TM 19000
A B C
TM 24000
A
862
218.95
B C TM25000 TN 35000
A B C
950
241.30
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 3
Wood Group ESP, INC.
ENGINEERING TABLES Pumps 50 Hz 2917 RPM Thrust Brg. Load Capacity Lbs.
Shaft Model
BHP Limit Dia. MM
Area 2 MM
Std.
HS
Std. @230F (Max.) #
Hi-Ld @250F (Max.) #
Maximum Number of Stages Using Thrust Brg. (Ref Seal Section) Shaft Floater Pump Cprsn. Pump Std. Hi-Ld Hi-Ld Std. HS @230F @250F @250F # # (Max.) # (Max.) # (Max.) #
Housing Std. #
Hi Pr #
TR 3 Seal Section
TA-400 TA-550 TA-900 TA-1200 TA-1500 TA-2200
15.875
197.93
78
125
17.463
239.50
104
167
TD-150 TD-300 TD-460 TD-650 TD-850 TD-1250 TD-1750 TD-2200 TD-3000 TD-4300 TD-6000
12.700
126.68
37
58
15.875
197.93
78
125
17.463
239.50
104
167
22.225
387.95
213
341
TG-4000
25.400
506.71
313
500
22.225
387.95
213
341
25.400
506.71
313
500
30.163
715.14
531
849
30.163
715.14
531
849
875
2500
413 414 435 461 413 391
1181 1184 1243 1316 1179 1118
165 159 159 161 157
1231 967 796 645 581 545
1969 1547 1274 1031 929 873
870 872 916 969 1050 998
870 872 916 969 1050 998
715 448 326 324 329 254 303 269 196 197 188
3965 2485 1807 1796 1824 1408 1682 1489 1087 1091 1042
323 299 248 272 262 183 501 442 460 352 293
782 1231 752 589 437 353 474 286 576 365 261
1244 1969 1203 942 699 565 758 457 922 584 418
708 693 504 501 509 475 568 502 594 596 570
849 832 605 601 610 570 681 603 713 715 684
157
800
346
346
554
308
370
154 159 148 125 137 133 135
784 806 752 635 697 677 687
294 277 246 158 288 397 397 207
269 236 134 175 191 157 157 208
431 378 214 281 306 251 251 333
277 285 266 294 322 313 317 399
277 285 266 294 322 313 317 399
207 145
101 78
161 125
143 137
171 164
296 214 175 133
155 104 80 73
249 167 129 116
124 85 96 99
149 102 115 119
75 90 111 76 90 113 69 27 33 39
47 64 73 31 32 45 31 24 33 42
75 102 117 49 52 71 50 39 52 67
45 54 67 44 53 67 40 36 43 51
54 65 80 53 64 80 48 43 51 61
TR 4 Seal Section
992
5500
TR 5 Seal Section
TE-1500 TE-2700 TE-3300 TE-4200 TE-5500 TE-7000 TE-7200 TE-11000 TH-15000 TH-20000
2008
10200
2008
10200
2008
10200
TR562 Seal Section
TJ-7500 TJ-9000 TJ-12000 TJ-20000 A B C A TM B 24000 C TM25000 A TN B 35000 C
30.163
715.14
531
849
17500
TM 19000
30.163
715.14
531
849
34.925
958.00
633
1013
38.100
1140.09
833
1333
17500
17500
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 4
Wood Group ESP, INC.
ENGINEERING TABLES Pumps 60 Hz 3500 RPM
Model
Series
338
TA-400 TA-550 TA-900 TA-1200 TA-1500 TA-2200 TD-150 TD-300 TD-460 TD-650 TD-850 TD-1250 TD-1750 TD-2200 TD-3000 TD-4300 TD-6000
400
TG-4000
513
Const.
O.D. Inches
3.38
4.00
513
Stage
Flt.
Cprsn.
Pancake
X X X X X X
X X X X X
X X X X X
X X X X X X X X X X X
X X X X X X X X X X X
X X X X X X X X
Mixed Flow
Recommended Operating Range - BPD
Maximum Downthrust Per Stage Cprsn. Pump Lbs.
BHP per Stage
S/O Head Per Stage Ft.
21.8 22.6 22.7 22.3 23.0
X
300-540 400-700 660-1060 900-1500 1000-2000 1250-2750
0.12 0.14 0.17 0.21 0.31 0.33
23.5 22.9 21.8 20.6 19 20
X X X X X
80-280 200-450 300-600 450-800 550-1020 800-1500 1200-2100 1400-2800 2000-3700 3000-5200 3500-7500
24.5 26.5 32.0 29.1 30.2 43.3 15.8 17.9 17.2 22.5 27.0
0.081 0.11 0.18 0.23 0.31 0.51 0.38 0.63 0.64 1.01 1.41
X
X
3200-4800
42.5
X X X X X X X X
X X X X X X X X
800-2250 1500-3300 2200-4500 2600-5400 3500-7300 4000-9700 4000-9550 8000-14000
X X X X X X
Housing Pressure Limit PSI Hi. Std. Pr. 6000
6000
23.5 24.0 33 33.2 32.7 35.0 29.3 33.1 28.0 27.9 29.2
5000
6000
1.56
54.0
5000
6000
50.0 53.0 59.7 93 51.0 37.0 37.0 71.0
1.37 1.56 2.75 3.08 2.82 3.44 3.44 4.41
72.0 70.0 75.0 68.0 62.0 63.8 62.9 50.0
6000
6000
TE-1500 TE-2700 TE-3300 TE-4200 TE-5500 TE-7000 TE-7200 TE-11000
538
5.38
TH-15000 TH-20000
562
5.62
X X
X X
10000-19000 15000-23500
71.0 101.0
9.10 11.70
70.0 73.0
3000
3600
6.75
X X X X X
X X X X X
5000-11000 5000-13000 7500-18000 12000-18000 12000-26000
85.0 118.0 144.0 145.0 190.0
5.90 8.80 11.40 12.25 12.63
80.5 117.0 104.0 93.5 101.0
3000
3600
862
8.62
X X X X X X X
X X X X X X X
14000-24000 13000-23000 12500-22500 14000-32000 20000-29000 19500-28500 14000-34000
335.0 280.3 227.9 330.0 278.7 223.0 365.0
19.50 14.40 12.51 30.0 28.30 20.60 35.26
147.0 123.0 100.0 150.2 125.0 100.0 166.0
2000
2400
950
9.50
X X X
X X X
31000-45000 28000-43000 25500-39000
925.0 770.1 645.3
58.89 44.10 34.25
215.0 179.0 150.0
2300
2760
TJ-7500 TJ-9000 TJ-12000 TJ-16000 TJ-20000 TM 19000 TM 24000
675
A B C A B C
TM25000 TN 35000
A B C
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 5
Wood Group ESP, INC.
ENGINEERING TABLES Pumps 60 Hz 3500 RPM Maximum Number of Stages Using
Thrust Brg. Load Capacity Lbs.
Shaft
Thrust Brg. (Ref Seal Section)
Model BHP Limit Dia. In.
TA-400 TA-550 TA-900 TA-1200 TA-1500 TA-2200
0.625
Area In.2
0.3068
Std.
94
HS
Std. Hi-Ld @230F @250F (Max.) (Max.) # # TR 3 Seal Section
150 1000
0.688
0.3712
125
200
TD-150 TD-300 TD-460 TD-650 TD-850 TD-1250 TD-1750 TD-2200 TD-3000 TD-4300 TD-6000
0.500
0.1963
44
70
0.625
0.3068
94
150
0.688
0.3712
125
200
0.875
0.6013
256
410
TG-4000
1.000
0.7854
375
600
2750
Floater Pump Std. Hi-Ld @230F @250F (Max.) # (Max.) #
Shaft
Cprsn. Pump Hi-Ld @250F (Max.) #
Housing
Std. #
HS #
Std. #
Hi Pr #
320 329 345 366 328 311
881 904 950 1005 901 854
126 122 121 123 120
783 671 553 448 403 379
1253 1074 885 716 645 606
590 605 636 673 729 693
590 605 636 673 729 693
596 373 272 270 274 212 253 224 163 164 157
3004 1882 1369 1361 1382 1067 1274 1128 823 826 789
245 226 188 206 199 139 380 335 349 267 222
543 855 522 409 303 245 329 198 400 253 182
864 1367 836 654 485 392 526 317 640 406 290
491 481 350 348 353 330 394 349 413 414 396
590 578 420 417 424 396 473 419 495 497 475
131
599
259
240
385
214
257
129 132 123 104 114 111 113
587 604 563 476 522 507 514
220 208 184 118 216 297 297 155
187 164 93 122 133 109 109 144
299 263 149 195 213 174 174 231
193 198 185 204 224 217 220 277
193 198 185 204 224 217 220 277
155 109
70 54
112 87
99 95
119 114
226 163 134 101 57 69 84 58 69 86 53 21 25 30
108 72 56 50 33 44 51 21 23 31 22 17 23 29
173 116 89 81 52 71 81 34 36 49 34 27 36 47
86 59 67 69 31 38 46 31 37 46 28 25 30 35
103 71 80 82 38 45 55 37 44 55 33 30 36 43
TR 4 Seal Section
1190
6000
TR 5 Seal Section
TE-1500 TE-2700 TE-3300 TE-4200 TE-5500 TE-7000 TE-7200 TE-11000
0.875
0.6013
256
410
1.000
0.7854
375
600
1.188
1.1085
637
1019
1.188
1.1085
637
1019
2410
2410
TH-15000 TH-20000
11000
11000
TR562 Seal Section
TJ-7500 TJ-9000 TJ-12000 TJ-20000 TM 19000 TM 24000
A B C A B C
TM25000 TN 35000
A B C
1.188
1.1085
637
1019
1.188
1.1085
637
1019
19250
19250
1.375
1.4849
760
1216
1.500
1.7671
1000
1600
19250
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 6
Wood Group ESP, INC.
ENGINEERING TABLES Model STD Motors 300 Series Motors (3.75” O.D.) H.P. Volts Amps 60 60 50 50 Hz Hz Hz Hz 7.5 10.5
6.3 8.8
15
12.5
18
15
19.5
16.3
22.5
18.8
25.5
21.3
410 390 315 400 900 265 387 630 330 440 730 370 500 630
342 325 263 333 750 220 323 525 275 367 608 308 417 525
14 20.5 35.5 28 14 51 38 23 51.5 38.5 23 51 37 30
400 Series Motors (4.56” O.D.) H.P. Volts Amps 60 50 50 60 Hz Hz Hz Hz 10
8.3
15
12.5
20
16.7
25
20.8
30
25
35
29.2
40
33.3
50
41.7
60
50
70
80
90
58.3
66.7
75
Model E56 Motors H.P. 60 Hz
50 Hz
200 250
166.7 208.3
300
250
350
291.7
400
333.3
450
375
Volts 60 50 Hz Hz 1403 1754 2055 2355 3858 1744 2105 2034 2455 3718 1847 2325 2806 2616 1960 2350 3698
1169 1462 1712 1962 3215 1453 1754 1695 2046 3098 1539 1937 2338 2180 1633 1958 3081
Amps 86 86 73 64 40 104 86 104 86 58 135 104 86 104 140 116 75
100
83.3
110
91.7
120
100
435 435 610 450 750 410 690 810 425 750 400 675 750 420 770 880 1295 675 815 955 1070 1210 640 810 970 1330 1945 540 750 945 1135 1310 1885 635 860 1085 1310 2155 710 960 1135 1220 1460 1930 775 1075 1355 2205 1190 1487 2380 930 1040 1125 1295 1625 2245
363 363 508 375 625 342 575 675 354 625 333 563 625 350 642 733 1079 563 679 796 892 1008 533 675 808 1108 1620 450 625 788 946 1092 1570 529 717 904 1092 1796 592 800 946 1017 1216 1608 646 896 1129 1838 992 1239 1983 775 867 938 1079 1354 1871
15 23 16 28.5 17 39 22 20 44.5 25.5 55 33 28 62 33 29 20 47 39 33 31 27 59 47 39 29 20 82.5 60 47 39 35 24 80 60 46 39 24 81 59 50 46 39 31 84 59 46 28.5 60 48 30 84 76 70 59 46 35
500 Series Motors (5.44” O.D.) H.P. Volts Amps 60 60 50 50 Hz Hz Hz Hz 20
16.7
30
25
40
33.3
50
41.7
60
50
70
58.3
80
66.6
100
83.3
120
100
130
108.3
140
116.7
150
125
160
133.3
180
150
200
166.7
225
187.5
290 440 755 1020 435 710 1215 435 730 880 1325 450 725 905 1270 1375 425 645 870 970 1085 1320 755 1015 1265 865 1160 2180 705 835 1070 1255 1450 2170 855 1030 1295 1450 2165 925 1125 985 1210 2015 1075 1240 2105 825 1115 1423 2003 2185 945 1275 1945 2260 1100 1415 2140 1135 2235
241 367 629 850 363 592 1013 363 608 733 1104 375 604 754 1058 1146 354 538 725 808 904 1100 629 846 1054 721 967 1817 588 696 892 1046 1208 1808 713 858 1079 1208 1804 771 938 821 1008 1679 896 1033 1754 688 929 1186 1669 1821 788 1063 1621 1883 917 1179 1783 946 1863
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
45 29 17 12 45 28 16 60 36 30 20 72 45 34 25 22 91 59 45 39 35 30 60 45 35 60 45 23 90 76 60 50 45 29 88 73 59 45 33 88 67 90 67 44 87 76 44 122 88.5 71 50 46 120 89 59 50 115 89 54 127 64
Pg. 7
Wood Group ESP, INC.
ENGINEERING TABLES Model THD Motors 300 Series Motors (3.75” O.D.) H.P. Volts Amps 60 60 50 50 Hz Hz Hz Hz
400 Series Motors (4.56” O.D.) H.P. Volts Amps 60 60 50 50 Hz Hz Hz Hz
500 Series Motors (5.44” O.D.) H.P. Volts Amps 60 60 50 50 Hz Hz Hz Hz
10 15 25
15 20
12.5 16.5
30
25
30
25
45
37.5
35
29.5
60
50
75
62.5
90
75
105
87.5
120
100
150
125
180
150
195 210
162.5 175
225
187.5
240
200
270
225
300
250
8.3 12.5 20.8
30
25
35
29.2
40
33.3
455 445 385 490 1100 455 745 390 520 865 440 595 750
379 371 320 408 917 379 621 325 433 721 367 496 625
17 26 49 39 19 50 30 68 51 30 68 49 40
45
37.5
50
41.5
60
50
75
90
62.5
75
105
87.5
120
100
135
112.5
150
125
165
137.5
180
150
505 480 675 525 870 465 780 915 495 870 455 770 855 490 895 1025 1505 785 945 1110 1245 1405 745 940 1130 1545 2260 630 870 1100 1320 1525 740 1000 1260 1525 2505 825 1115 1320 1420 1695 2245 900 1250 1575 2565 1385 1728 2765 1080 1210 1310 1505 2610
421 400 563 437 725 387 650 763 413 725 379 642 710 408 746 854 1254 654 787 925 1037 1171 620 783 941 1288 1883 525 725 917 1100 1271 616 833 1050 1271 2088 687 929 1100 1183 1413 1871 750 1041 1313 2138 1154 1440 2304 900 1008 1091 1254 2175
20 28 20 38 23 49 28 25 59 34 71 42 36 83 44 39 27 63 52 44 41 36 79 63 52 39 27 110 80 63 52 47 107 80 61 52 32 108 79 67 61 52 41 112 79 61 38 80 64 40 112 101 93 79 47
515 880 1190 505 830 1415 505 850 1025 1545 525 845 1055 1480 1605 750 1015 1130 1265 1540 880 1185 1475 1010 1355 2545 975 1250 1465 1690 2530 1200 1510 2030 2525 1310 1150 1410 2350 1255 1445 2455 1300 1660 2335 2550 1485 2270 2635 1285 1510 1650 2495
429 733 992 421 691 1179 421 708 854 1288 437 704 879 1233 1338 625 846 942 1041 1283 733 988 1229 841 1129 2121 812 1041 1221 1408 2108 1000 1258 1691 2104 1092 958 1175 1958 1046 1204 2046 1083 1383 1946 2125 1238 1892 2196 1071 1258 1375 2079
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
37 22 15 58 36 21 77 46 39 26 93 58 44 32 28 76 58 50 45 39 77 58 45 77 58 30 98 77 65 58 37 94 76 58 43 87 116 87 57 112 98 57 114 92 65 59 115 76 65 149 127 115 70
Pg. 8
Wood Group ESP, INC.
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 9
Wood Group ESP, INC.
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009 Pg. 10
Wood Group ESP, INC.
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009 Pg. 11
Wood Group ESP, INC.
ENGINEERING TABLES API Tubular Goods SIZE INCHES (MM) THREAD NOMINAL OD API LINE PIPE: 1-¼ (31.8) 11-1/2 V 1-½ (38.1) 11 to 11-1/2V 2 (50.8) 2-3/8 (60.3) 11-1/2 V 3 (76.2) 3-1/2 (88.9) 8V 4 (101.6) 4-½ (114.3) 8V 6 (152.4) 6-5/8 (168.4) 8V 8 (203.2) 8-5/8 (219.2) 8V API TUBING (NON UPSET): 1-½ (38.1) 10 RD 2 (50.8) 2-3/8 (60.3) 10 RD 2-½ (63.5) 2-7/8 (73.0) 10 RD 3 (76.2) 3-½ (88.9) 10 RD 3-½ (88.9) 4 (101.6) 8 RD API TUBING (EXTERNAL UPSET): 1-½ (38.1) 10 RD 2 (50.8) 2-3/8 (60.3) 8 RD 2-½ (63.5) 2-7/8 (73.0) 8 RD 3 (76.2) 3-½ (88.9) 8 RD 3-½ (88.9) 4 (101.6) 8 RD 4 (101.6) 4-½ (114.3) 8 RD API TUBING REGULAR CASING: 8 RD 8 RD 4-½ (114.3) 8 RD 8 RD 8 RD 5-½ (139.7) 8 RD 8 RD 8 RD 8 RD 6-5/8 (168.4) 8 RD 8 RD 8 RD 8 RD 8 RD 7 (177.8) 8 RD 8 RD 8 RD 8 RD 8-5/8 (219.1) 8 RD 8 RD 8 RD 8 RD 9-5/8 (244.5) 8 RD 8 RD 8 RD 10-3/4 (273.1) 8 RD 8 RD 13-3/8 (339.9) 8 RD
WEIGHT LB / FT
OD
DIAMETER INCHES / MM ID
2.30 2.75 3.75 7.70 11.00 19.45 25.55
1.660 / 42.2 1.900 / 48.3 2.375 / 60.3 3.500 / 88.9 4.500 / 114.3 6.625 / 168.3 8.625 / 219.1
1.380 / 35.1 1.610 / 40.1 2.067 / 52.5 3.068 / 77.9 4.026 / 102.3 6.065 / 167.8 8.071 / 205.0
2.75 4.00 6.40 7.70 9.50
1.900 / 48.3 2.375 / 60.3 2.875 / 73.0 3.500 / 88.9 4.000 / 101.6
1.610 / 40.9 2.041 / 51.8 2.441 / 62.0 3.068 / 77.9 3.548 / 90.1
1.516 / 38.5 1.947 / 49.5 2.347 / 59.6 2.943 / 74.8 3.423 / 87.0
2.200 / 55.8 2.875 / 73.03 3.500 / 88.9 4.250 / 108.0 4.750 / 120.7
2.90 4.70 6.50 9.30 11.00 12.75
1.900 / 48.3 2.375 / 60.3 2.875 / 73.0 3.500 / 88.9 4.000 / 101.6 4.500 / 114.3
1.610 / 40.9 1.995 / 50.7 2.441 / 62.0 2.992 / 76.0 3.476 / 88.3 3.958 / 100.5
1.516 / 38.5 1.901 / 48.3 2.347 / 59.61 2.867 / 72.8 3.351 / 85.1 3.833 / 97.4
2.500 / 63.5 3.063 / 77.8 3.668 / 93.2 4.500 / 114.3 5.000 / 127.0 5.563 / 141.3
4.090 / 103.9 4.000 / 101.6 3.920 / 99.56 5.012 / 127.3 4.892 / 124.3 4.778 / 121.4 4.670 / 118.61 6.135 / 155.8 5.921 / 150.4 5.791 / 147.09 5.675 / 144.14 6.456 / 164.0 6.366 / 161.7 6.276 / 159.4 6.184 / 157.07 6.094 / 154.78 8.017 / 203.6 7.921 / 201.19 7.825 / 198.8 7.725 / 196.21 8.921 / 226.6 8.835 / 224.4 8.681 / 220.49 8.535 / 216.78 10.050 / 255.3 9.760 / 247.9 12.715/ 323.0 12.415/ 315.3
3.965 / 100.7 3.875 / 98.43 3.795 / 96.39 4.887 / 124.1 4.767 / 121.1 4.653 / 118.2 4.545 / 115.44 6.010 / 152.7 5.796 / 147.2 5.666 / 143.91 5.550 /140.97 6.331 / 160.8 6.241 / 158.5 6.151 / 156.2 6.059 / 153.89 5.959 / 151.35 7.892 / 200.5 7.796 / 198.0 7.700 / 195.6 7.600 / 193.04 8.765 /222.6 8.679 / 220.5 8.525 / 216.53 8.379 / 212.82 9.894 / 251.3 9.604 / 243.9 12.559/ 319.0 12.259/ 311.4
9.50 11.60 13.50 14.00 17.00 20.00 23.00 17.00 24.00 28.00 32.00 20.00 23.00 26.00 29.00 32.00 28.00 32.00 36.00 40.00 36.00 40.00 47.00 53.50 40.50 55.50 48.00 68.00
4.500 / 114.3
5.500 / 139.7
6.625 / 168.4
7.000 / 177.8
8.625 / 219.1
9.625 / 244.5 10.750/ 273.1 13.375/ 339.9
COUPLINGOD
DRIFT
INCHES / MM 2.054 / 52.2 2.200 / 55.9 2.875 / 73.0 4.000 / 101.6 5.200 / 132.1 7.390 / 187.7 9.625 / 244.5
5.000 / 127.0
6.050 / 153.7
7.390 / 187.7
7.656 / 194.5
9.625 / 244.5
10.625/ 269.9 11.750/ 298.5 14.375/ 365.1
Copyright Wood Group ESP March 2009
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 12
Wood Group ESP, INC.
Intentionally left Blank
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 13
Wood Group ESP, INC.
ENGINEERING TABLES Gravity Correction Table Weight (Density) Gallon Cubic Barrel Foot Pounds 6.16 46.1 259.0 6.20 46.4 260.0 6.23 46.6 262.0 6.26 46.8 263.0 6.30 47.1 265.0
Degrees API
Specific Gravity
60.0 59.0 58.0 57.0 56.0
0.739 0.743 0.747 0.751 0.755
55.0 54.0 53.0 52.0 51.0
0.759 0.763 0.767 0.771 0.775
6.33 6.36 6.40 6.43 6.46
47.4 47.6 47.9 48.1 48.3
50.0 49.0 48.0 47.0 46.0
0.780 0.784 0.788 0.793 0.797
6.51 6.54 6.57 6.61 6.65
45.0 44.0 43.0 42.0 41.0
0.802 0.806 0.811 0.816 0.820
40.0 39.0 38.0 37.0 36.0
Fluid Head Pressure per Foot Height per Pound
Buoyancy Factor
Lbs / Sq In 0.320 0.322 0.324 0.325 0.327
Feet 3.13 3.11 3.09 3.08 3.06
Totally Immersed 0.906 0.905 0.905 0.904 0.904
266.0 267.0 269.0 270.0 271.0
0.329 0.330 0.332 0.334 0.336
3.04 3.03 3.01 2.99 2.98
0.903 0.903 0.902 0.902 0.901
48.7 48.9 49.2 49.5 49.8
273.0 275.0 276.0 278.0 279.0
0.338 0.340 0.341 0.343 0.345
2.96 2.94 2.93 2.92 2.90
0.901 0.900 0.900 0.899 0.898
6.69 6.72 6.76 6.81 6.84
50.0 50.3 50.6 50.9 51.2
281.0 282.0 284.0 286.0 287.0
0.348 0.349 0.351 03354 0.355
2.87 2.87 2.85 2.82 2.82
0.898 0.897 0.897 0.896 0.896
0.825 0.830 0.835 0.840 0.845
6.88 6.92 6.96 7.01 7.05
51.5 51.8 52.1 52.4 52.7
289.0 291.0 292.0 294.0 296.0
0.357 0.359 0.362 0.364 0.366
2.80 2.79 2.76 2.75 2.73
0.895 0.894 0.894 0.893 0.892
35.0 34.0 33.0 32.0 31.0
0.850 0.855 0.860 0.865 0.871
7.09 7.13 7.17 7.21 7.26
53.0 53.3 53.6 53.9 54.3
298.0 299.0 301.0 303.0 305.0
0.368 0.370 0.372 0.375 0.377
2.72 2.70 2.69 2.67 2.65
0.892 0.891 0.891 0.890 0.889
30.0 29.0 28.0 27.0 26.0
0.876 0.882 0.877 0.893 0.898
7.31 7.36 7.40 7.45 7.49
54.7 55.1 55.4 55.7 56.0
307.0 309.0 311.0 313.0 315.0
0.380 0.382 0.384 0.387 0.389
2.63 2.62 2.60 2.58 2.57
0.889 0.887 0.887 0.886 0.885
25.0 24.0 23.0 22.0 21.0
0.904 0.910 0.916 0.922 0.928
7.54 7.59 7.64 7.69 7.74
56.4 56.8 57.2 57.5 57.9
317.0 319.0 321.0 323.0 325.0
0.392 0.394 0.397 0.399 0.402
2.55 2.54 2.52 2.51 2.49
0.885 0.884 0.883 0.883 0.882
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 14
Wood Group ESP, INC.
ENGINEERING TABLES Gravity Correction Table (continued) Weight (Density) Cubic Gallon Barrel Foot Pounds 7.79 58.3 327.0 7.78 58.7 329.0 7.89 59.0 331.0 7.95 59.5 334.0 8.00 59.8 336.0
Fluid Head Pressure per Foot
Height per Pound
Buoyancy Factor
Lbs / Sq In 0.405 0.407 0.410 0.413 0.416
Feet 2.47 2.46 2.44 2.42 2.40
Totally Immersed 0.881 0.880 0.879 0.879 0.878
339.0 342.0 343.0 345.0 348.0
0.419 0.421 0.424 0.427 0.430
2.39 2.38 2.36 2.34 2.33
0.877 0.876 0.876 0.874 0.874
62.4 62.8 64.3 65.8 67.3
350.0 353.0 361.0 370.0 378.0
0.433 0.436 0.447 0.457 0.468
2.31 2.29 2.24 2.19 2.14
0.873 0.872 0.869 0.866 0.862
9.20 9.40 9.60 9.625 9.80
68.8 70.3 71.8 72.0 73.3
386.0 395.0 403.0 404.0 412.0
0.478 0.488 0.499 0.500 0.509
2.09 2.05 2.00 2.00 1.96
0.860 0.856 0.853 0.853 0.850
1.20 1.22 1.25 1.27 1.29
10.0 10.2 10.4 10.6 10.8
74.8 76.3 77.8 79.3 80.8
420.0 428.0 437.0 445.0 454.0
0.519 0.530 0.540 0.551 0.561
1.93 1.89 1.85 1.81 1.78
0.847 0.844 0.841 0.838 0.835
1.32 1.34 1.37 1.39 1.41
11.0 11.2 11.4 11.6 11.8
82.3 83.8 85.3 86.8 88.3
462.0 470.0 479.0 487.0 496.0
0.571 0.582 0.592 0.603 0.613
1.75 1.72 1.69 1.66 1.63
0.832 0.829 0.826 0.823 0.820
1.44 1.46 1.49 1.51 1.53
12.0 12.2 12.4 12.6 12.8
89.8 91.3 92.8 94.3 95.8
504.0 512.0 521.0 529.0 538.0
0.623 0.634 0.644 0.655 0.665
1.61 1.58 1.55 1.53 1.50
0.817 0.814 0.810 0.808 0.804
1.56 1.58 1.61 1.63 1.65
13.0 13.2 13.4 13.6 13.8
97.2 98.7 100.0 102.0 103.0
546.0 554.0 563.0 571.0 580.0
0.675 0.686 0.696 0.706 0.717
1.48 1.46 1.44 1.42 1.39
0.801 0.798 0.795 0.792 0.789
Degrees API
Specific Gravity
20.0 19.0 18.0 17.0 16.0
0.934 0.940 0.946 0.953 0.959
15.0 14.0 13.0 12.0 11.0
0.966 0.973 0.979 0.986 0.993
8.06 8.11 8.16 8.22 8.28
60.3 60.7 61.0 61.5 61.9
10.0 Degrees API or Pure Water
1.00 1.01 1.03 1.06 1.08
8.34 8.40 8.60 8.80 9.00
Salt Water
1.10 1.13 1.15 1.154 1.18
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 15
Wood Group ESP, INC.
ENGINEERING TABLES Electrical Terms and Definitions Term AC Amperes
Definition Alternating Current unit of current or rate at flow of electricity.
Term Power Factor Watthour
Volt
unit of electromotive force
Horsepower
Ohm Ohms Law for DC Current Ohms DC
unit of resistance
Torque Formulas:
Volt Amperes Megohm
unit of apparent power 1,000,000 Ohms
Watt
unit of true power = volt amperes x power factor
Electromotive Force / Resistance Volts / Amperes Direct Current
To Find
Definition ratio of true to apparent power unit of electrical work; indicates expenditure of electrical power of one watt for one hour. A measure of time rate of doing work; equivalent to raising 33,000-lbs one ft. in one minute. 1 hp = 746 watts
T=
T=FxR
HPx5252 N
Where:
T = Torque (lb-ft) HP = Horsepower N = Speed (RPM)
Where:
F = Force (lbs) R = Radius (ft)
Inflow Performance Relationships for Solution – Gas Drive Wells (Below Bubble Point)
Formula
Brake HP
GPM x HeadFeet x SpGr 3960 x Pump%Eff
Brake HP
BPD x HeadFeet x SpGr 136,000 x Pump%Eff Amp x Volt x 1.732 x PF 746
Qo Pwf = 1 − 0.20 Qo Max Pr
Pr
Pwf − 0.80 Pr
2
Static Reservoir Pressure at Producing Zone
HP Input Pwf Flowing Wellbore Pressure at Producing Zone (Three Phase) HP Input KW x 1.34 Qo Production Rate at Pwf (Three Phase) Qo Max Production Rate at 100% Drawdown, Pwf = 0 Where HP = Horsepower; GPM = Gallons Per Minute; Sp Gr = Specific Gravity; Pump % Eff = Pump Percent Efficiency BPD = Barrels Per Day; Amp = Amperes; Volt = Surface Voltage; PF = Power Factor; KW = Kilowatts
Formulas for Determining Kilowatts, KVA, Horsepower and Amperes Desired Data Kilowatts Kilovolt – Ampere Horsepower (Output) Amperes (When HP is known) Amperes (When Kilowatts are known)
Alternating Current Single Phase
Three Phase
Volts x Amps x Pf 1000 Volts x Amps 1000 Volts x Amps x Eff x Pf 746 x 100 HP x 746 Volts x Eff x HP Kilowatts x 1000 Volts x PF
1.732 x Volts x Amps x Pf 1000 1.732 x Volts x Amps 1000 1.732 x Volts x Amps x Eff x Pf 746 x 100 HP x 746 1.732 x Volts x Eff x PF Kilowatts x 1000 1.732 x Volts x PF
Copyright Wood Group ESP January 2000
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 16
Wood Group ESP, INC.
Abbreviations, Electrical Terms and Definitions Term AC Amperes (Amp) (A) API
Definition Alternating Current Unit of current or rate at flow of electricity. American Petroleum Institute
AR ASSY BEP BHT BO
Abrasion Resistant Assembly Best Efficiency Point Bottom Hole Temperature Bolt-On
BPD Brake Horsepower (BHP)
Barrels Per Day The net effective power of a prime mover
BRG
Bearing Wellhead Casing Pressure Construction Compression Stage Direct Current Dog Leg Severity Guaranteed minimum inside diameter of API tubulars Efficiency Floater Stage Feet Gas / Liquid Ratio Gas / Oil Ratio Gallons Per Minute Gas Separator
CP CONST CMP DC DLS Drift EFF FLT FT GLR GOR GPM GS Horsepower (HP)
Term Ohms Law for DC Current Ohms PB PBTD PIP PMP Power Factor (PF) PR PSD Pump % Eff PWF Q Qmin Qmax SHD Sp Gr SST STBPD STD STGS STL TA TD TE TF TG TH
Definition Electromotive Force / Resistance Volts / Amperes Bubble Point Pressure Plug Back Total Depth Pump Intake Pressure Pump Ratio of true to apparent power Reservoir Pressure Pump Setting Depth Pump Percent Efficiency Producing Bottom Hole Pressure Volume Flow Rate Minimum volumetric flow rate Maximum volumetric flow rate Shroud Specific Gravity Stainless Steel Stock Tank Barrels Per Day Standard Stages Steel 338 Series Equipment 400 Series Equipment Total Depth 538 Series Equipment Tubing Friction Loss
HL
A measure of time rate of doing work; equivalent to raising 33,000lbs one ft. in one minute. 1 hp = 746 watts High Load
HIPR HSG HSS
High Pressure Housing High Strength Shaft
Hz ID KG KW LBS M MCF MD Megohm MMSCF MTR
Hertz Inside Diameter Kilograms Kilowatts Pounds Meters Thousand cubic feet Measured Depth 1,000,000 Ohms Million cubic feet Motor
NO
Number
YO ( SGo)
Oil Specific Gravity
OD
Outside Diameter
YW ( SGw)
Water Specific Gravity
Ohm
Unit of resistance
THD
513 Series Equipment 562 Series Equipment Motors rated for wellbore conditions
TJ
675 Series Equipment
TM TN
862 Series Equipment 950 Series Equipment Wellhead Tubing Pressure
TP TVD Volt ( ) Volt Amperes Watt Watt-hour
WC YG ( SGg)
True Vertical Depth Unit of electromotive force Surface Voltage Unit of apparent power unit of true power = volt amperes x power factor Unit of electrical work; indicates expenditure of electrical power of one watt for one hour. Water Cut Gas Specific Gravity
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 17
Wood Group ESP, INC.
ENGINEERING TABLES Electrical Terms and Definitions Term AC Amperes
Definition Alternating Current unit of current or rate at flow of electricity.
Term Power Factor Watthour
Volt
unit of electromotive force
Horsepower
Ohm Ohms Law for DC Current Ohms DC
unit of resistance
Torque Formulas:
Volt Amperes Megohm
unit of apparent power 1,000,000 Ohms
Watt
unit of true power = volt amperes x power factor
Electromotive Force / Resistance Volts / Amperes Direct Current
To Find
T=
T=FxR
Formula
Definition ratio of true to apparent power unit of electrical work; indicates expenditure of electrical power of one watt for one hour. A measure of time rate of doing work; equivalent to raising 33,000-lbs one ft. in one minute. 1 hp = 746 watts HPx5252 N
Where:
T = Torque (lb-ft) HP = Horsepower N = Speed (RPM)
Where:
F = Force (lbs) R = Radius (ft)
Inflow Performance Relationships for Solution – Gas Drive Wells (Below Bubble Point)
Brake HP
GPM x HeadFeet x SpGr 3960 x Pump%Eff
Brake HP
BPD x HeadFeet x SpGr 136,000 x Pump%Eff Amp x Volt x 1.732 x PF 746
Qo Pwf = 1 − 0.20 Qo Max Pr
Pr
Pwf − 0.80 Pr
2
Static Reservoir Pressure at Producing Zone
HP Input Pwf Flowing Wellbore Pressure at (Three Phase) Producing Zone HP Input KW x 1.34 Qo Production Rate at Pwf (Three Phase) Qo Max Production Rate at 100% Drawdown, Pwf = 0 Where HP = Horsepower; GPM = Gallons Per Minute; Sp Gr = Specific Gravity; Pump % Eff = Pump Percent Efficiency BPD = Barrels Per Day; Amp = Amperes; Volt = Surface Voltage; PF = Power Factor; KW = Kilowatts
Formulas for Determining Kilowatts, KVA, Horsepower and Amperes Desired Data Kilowatts Kilovolt – Ampere Horsepower (Output) Amperes (When HP is known) Amperes (When Kilowatts are known)
Alternating Current Single Phase
Three Phase
Volts x Amps x Pf 1000 Volts x Amps 1000 Volts x Amps x Eff x Pf 746 x 100 HP x 746 Volts x Eff x HP Kilowatts x 1000 Volts x PF
1.732 x Volts x Amps x Pf 1000 1.732 x Volts x Amps 1000 1.732 x Volts x Amps x Eff x Pf 746 x 100 HP x 746 1.732 x Volts x Eff x PF Kilowatts x 1000 1.732 x Volts x PF
Copyright Wood Group ESP January 2000
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 18
Wood Group ESP, INC.
Conversion Factors MULTIPLY Feet Inches Square Inches
BY TO OBTAIN Length 0.3048 Meters 25.4 Millimeters Area 6.4516 Sq. Centimeters Volume 7.481 Gallons 0.02832 Cubic Meters
Cubic Feet Cubic Inches Barrels (US Pet.)
Gallons (Imperial) Gallons (US Liq.)
Cubic Meters Liters Tons (Metric) 36° Crude
16.387 5.6146 42 0.159 1.2009 231 128 8 4 35.31 6.2898 1000 0.001 7.452
Cu. Centimeters Cubic Feet Gallons (US Liq.) Cubic Meters Gallons (US Liq.) Cubic Inches Ounces (US Liq.) Pints (US Liq.) Quarts (US Liq.) Cubic Feet Barrels (US Pet.) Cu. Centimeters Cubic Meters Barrels (US Pet.)
Volume Ratios Cu. Feet / Cu. Foot 5.615 Cu. Feet / Bbl. Cu. Meters / Cu. Meter 5.615 Cu. Feet / Bbl. Feet / Second Feet / Minute Meters / Second Meters / Minute Cubic Feet / Day Barrels / Minute Barrels / Hour Barrels / Day Gallons / Minute Cu. Meters / Hour Cu. Meters / Day °Celsius + 17.78 °Celsius + 273 °Fahrenheit - 32 °Fahrenheit + 460 Foot-Pound
Velocity 0.3048 Meters / Second 0.00508 Meters / Second 3.2808 Feet / Second 0.05468 Feet / Second Volumetric Flow Rate 0.1781 Barrels / Day 0.2831 Cu. Meters / Day 1440 Barrels / Day 228.9 24 3.816 0.159 34.29 5.451 150.9 24 6.289 Temperature 1.8 1 0.5555 1 Torque 1.356
Cu. Meters / Day Barrels / Day Cu. Meters / Day Cu. Meters / Day Barrels / Day Cu. Meters / Day Barrels / Day Cu. Meters / Day Barrels / Day
MULTIPLY Kilograms Tons (Long)
BY Weight 2.6792 2722.22
Pounds (Troy) Pounds (Troy)
Tons (Short) Tons (Metric)
2430.55 1000
Pounds (Troy) Kilograms
Linear Weight 0.672 Pounds / Foot 1.488 Kgs. / Meter
Kgs. / Meter Pounds / Foot
Meters of Water
Pressure 14.7 101.32 29.92 760 14.5 100 14.22 98.07 0.145 6.895 0.4335 2.989 1.422
Pounds / Cu. Ft.
9.806 Density 16.0184
Atmospheres
Bar Kilograms / Sq. Cm. Kilopascals Pounds / Sq. In. Feet of Water
Pounds / Cu. In. Pounds / Gallon Kgs. / Cu. Meter Cubic Feet of Water
27.68 7.48 0.06243 62.43
Bbls/Day / Bar 2
0.07031 0.001621 6.895 0.159 0.02307 0.4279 0.00987 0.4336 0.01
Bbls/Day / KPa Bbls/Day / PSI Cu. Meter/Day / Atm. Cu. Meter/Day / Bar Cu. Meter/Day / PSI
°Fahrenheit °Kelvin °Celsius °Rankin Newton-Meters
Pounds / Sq. In. Kilopascals Inches of Mercury Millimeters of Mercury Pounds / Sq. In. Kilopascals Pounds / Sq. In. Kilopascals Pounds / Sq. In. Kilopascals Pounds / Sq. In. Kilopascals Pounds / Sq. In. Kilopascals Kgs. / Cu. Meter Grams / Cu. Cm. Pounds / Cu. Ft. Pounds / Cu. Ft. Pounds of Water
Productivity Index 0.06805 Bbls/Day / PSI 0.001569 Cu. Meter/Day / KPa 0.06895 Bbls/Day / PSI 0.00159 Cu. Meter/Day / KPa
Bbls/Day / Atm
Bbls/Day / Kg/Cm
TO OBTAIN
Bbls/Day / PSI Cu. Meter/Day / KPa Bbls/Day / PSI Cu. Meter/Day / KPa Cu. Meter/Day / KPa Bbls/Day / PSI Cu. Meter/Day / KPa Bbls/Day / PSI Cu. Meter/Day / KPa
Cu. Meter/Day / KPa
6.289 0.145 0.4422 0.01019 43.35
Bbls/Day / PSI Cu. Meter/Day / KPa Bbls/Day / PSI Cu. Meter/Day / KPa Bbls/Day / PSI
Horsepower
Power 0.7457
Kilowatts
Cu. Meter/Day / Kg/Cm
2
Product Catalog - Engineering Data - Copyright Wood Group ESP, INC. - October, 2009
Pg. 19
