Water turbine From Wikipedia, the free encyclopedia
Kaplan turbine and electrical generator cut-away view.
The runner of the small water turbine
A water turbine is a rotary engine that takes energy from moving water.
Water turbines were developed in the 19th century and were widely used for industrial power prior to electrical grids. Now they are mostly used for electric power generation. They harness a clean and renewable energy source. Contents [hide]
1 History
o
1.1 Swirl
o
1.2 Time line
o
1.3 A new concept
2 Theory of operation
o
2.1 Reaction turbines
o
2.2 Impulse turbines
o
2.3 Power
o
2.4 Pumped storage
o
2.5 Efficiency
3 Types of water turbines
4 Design and application
o
4.1 Typical range of heads
o
4.2 Specific speed
o
4.3 Affinity laws
o
4.4 Runaway speed
5 Maintenance
6 Environmental impact
7 See also
8 References
9 Sources
10 External links
History Water wheels have been used for thousands of years for industrial power. Their main shortcoming is size, which limits the flow rate andhead that can be harnessed. The migration from water wheels to modern turbines took about one hundred years. Development occurred during the Industrial revolution, using scientific principles
and methods. They also made extensive use of new materials and manufacturing methods developed at the time.
Swirl The word turbine was introduced by the French engineer Claude Bourdin in the early 19th century and is derived from the Latin word for "whirling" or a "vortex". The main difference between early water turbines and water wheels is a swirl component of the water which passes energy to a spinning rotor. This additional component of motion allowed the turbine to be smaller than a water wheel of the same power. They could process more water by spinning faster and could harness much greater heads. (Later, impulse turbines were developed which didn't use swirl).
Time line
Roman turbine mill at Chemtou, Tunisia. The tangential water inflow of the millrace made the submerged horizontal wheel in the shaft turn like a true turbine.[1]
A Francis turbine runner, rated at nearly one million hp (750 MW), being installed at the Grand Coulee Dam, United States.
A propeller-type runner rated 28,000 hp (21 MW)
The earliest known water turbines date to the Roman Empire. Two helix-turbine mill sites of almost identical design were found at Chemtou andTestour, modern-day Tunisia, dating to the late 3rd or early 4th century AD. The horizontal water wheel with angled blades was installed at the bottom of a water-filled, circular shaft. The water from the mill-race entered tangentially the pit, creating a swirling water column which made the fully submerged wheel act like a true turbine.[1] Ján Andrej Segner developed a reactive water turbine in the mid-18th century. It had a horizontal axis and was a precursor to modern water turbines. It is a very simple machine that is still produced today for use in small hydro sites. Segner worked with Euler on some of the early mathematical theories of turbine design. In 1820, Jean-Victor Poncelet developed an inward-flow turbine. In 1826, Benoit Fourneyron developed an outward-flow turbine. This was an efficient machine (~80%) that sent water through a runner with blades curved in one dimension. The stationary outlet also had curved guides. In 1844, Uriah A. Boyden developed an outward flow turbine that improved on the performance of the Fourneyron turbine. Its runner shape was similar to that of a Francis turbine. In 1849, James B. Francis improved the inward flow reaction turbine to over 90% efficiency. He also conducted sophisticated tests and developed engineering methods for water turbine design. The Francis turbine, named for him, is the first modern water turbine. It is still the most widely used water turbine in the world today. The Francis turbine is also called a radial flow turbine, since water flows from the outer circumference towards the centre of runner. Inward flow water turbines have a better mechanical arrangement and all modern reaction water turbines are of this design. As the water swirls inward, it accelerates, and transfers energy to the runner. Water pressure
decreases to atmospheric, or in some cases subatmospheric, as the water passes through the turbine blades and loses energy. Around 1890, the modern fluid bearing was invented, now universally used to support heavy water turbine spindles. As of 2002, fluid bearings appear to have a mean time between failures of more than 1300 years. Around 1913, Viktor Kaplan created the Kaplan turbine, a propeller-type machine. It was an evolution of the Francis turbine but revolutionized the ability to develop low-head hydro sites.
A new concept
Figure from Pelton's original patent (October 1880)
Main article: Pelton wheel All common water machines until the late 19th century (including water wheels) were basically reaction machines; water pressure head acted on the machine and produced work. A reaction turbine needs to fully contain the water during energy transfer. In 1866, California millwright Samuel Knight invented a machine that took the impulse system to a new level.[2][3] Inspired by the high pressure jet systems used in hydraulic mining in the gold fields, Knight developed a bucketed wheel which captured the energy of a free jet, which had converted a high head (hundreds of vertical feet in a pipe or penstock) of water to kinetic energy. This is called an impulse or tangential turbine. The water's velocity, roughly twice the velocity of the bucket periphery, does a u-turn in the bucket and drops out of the runner at low velocity.
In 1879, Lester Pelton (1829-1908), experimenting with a Knight Wheel, developed a double bucket design, which exhausted the water to the side, eliminating some energy loss of the Knight wheel which exhausted some water back against the center of the wheel. In about 1895, William Doble improved on Pelton's halfcylindrical bucket form with an elliptical bucket that included a cut in it to allow the jet a cleaner bucket entry. This is the modern form of the Pelton turbine which today achieves up to 92% efficiency. Pelton had been quite an effective promoter of his design and although Doble took over the Pelton company he did not change the name to Doble because it had brand name recognition. Turgo and Crossflow turbines were later impulse designs.
Theory of operation Flowing water is directed on to the blades of a turbine runner, creating a force on the blades. Since the runner is spinning, the force acts through a distance (force acting through a distance is the definition of work). In this way, energy is transferred from the water flow to the turbine Water turbines are divided into two groups; reaction turbines and impulse turbines. The precise shape of water turbine blades is a function of the supply pressure of water, and the type of impeller selected.
Reaction turbines Reaction turbines are acted on by water, which changes pressure as it moves through the turbine and gives up its energy. They must be encased to contain the water pressure (or suction), or they must be fully submerged in the water flow. Newton's third law describes the transfer of energy for reaction turbines. Most water turbines in use are reaction turbines and are used in low (<30m/98 ft) and medium (30-300m/98– 984 ft) head applications. In reaction turbine pressure drop occurs in both fixed and moving blades.
Impulse turbines Impulse turbines change the velocity of a water jet. The jet pushes on the turbine's curved blades which changes the direction of the flow. The resulting change in momentum (impulse) causes a force on the turbine blades. Since the turbine is spinning, the force acts through a distance (work) and the diverted water flow is left with diminished energy. Prior to hitting the turbine blades, the water's pressure (potential energy) is converted to kinetic energy by a nozzle and focused on the turbine. No pressure change occurs at the turbine blades, and the turbine doesn't require a housing for operation. Newton's second law describes the transfer of energy for impulse turbines.
Impulse turbines are most often used in very high (>300m/984 ft) head applications .
Power The power available in a stream of water is;
where:
P = power (J/s or watts)
η = turbine efficiency
ρ = density of water (kg/m³)
g = acceleration of gravity (9.81 m/s²)
h = head (m). For still water, this is the difference in height between the inlet and outlet surfaces. Moving water has an additional component added to account for the kinetic energy of the flow. The total head equals the pressure head plus velocity head.
= flow rate (m³/s)
Pumped storage Some water turbines are designed for pumped storage hydroelectricity. They can reverse flow and operate as a pump to fill a high reservoir during off-peak electrical hours, and then revert to a turbine for power generation during peak electrical demand. This type of turbine is usually a Deriaz or Francis in design.
Efficiency Large modern water turbines operate at mechanical efficiencies greater than 90% (not to be confused with thermodynamic efficiency).
Types of water turbines
Various types of water turbine runners. From left to right: Pelton Wheel, two types of Francis Turbine and Kaplan Turbine
Reaction turbines:
Francis
Kaplan, Propeller, Bulb, Tube, Straflo
Tyson
Gorlov
Waterwheel
Pelton
Turgo
Michell-Banki (also known as the Crossflow or Ossberger turbine)
Jonval turbine
Reverse overshot water-wheel
Archimedes' screw turbine
Impulse turbine
Design and application
Turbine selection is based mostly on the available water head, and less so on the available flow rate. In general, impulse turbines are used for high head sites, and reaction turbines are used for low head sites. Kaplan turbines with adjustable blade pitch are well-adapted to wide ranges of flow or head conditions, since their peak efficiency can be achieved over a wide range of flow conditions. Small turbines (mostly under 10 MW) may have horizontal shafts, and even fairly large bulb-type turbines up to 100 MW or so may be horizontal. Very large Francis and Kaplan machines usually have vertical shafts because this makes best use of the available head, and makes installation of a generator more economical. Pelton wheels may be either vertical or horizontal shaft machines because the size of the machine is so much less than the available head. Some impulse turbines use multiple water jets per runner to increase specific speed and balance shaft thrust.
Typical range of heads • Hydraulic wheel turbine
0.2 < H < 4 (H = head in m)
• Archimedes' screw turbine
1 < H < 10
• Kaplan
2 < H < 40
• Francis
10 < H < 350
• Pelton
50 < H < 1300
• Turgo
50 < H < 250
Specific speed Main article: Specific speed The specific speed ns of a turbine characterizes the turbine's shape in a way that is not related to its size. This allows a new turbine design to be scaled from an existing design of known performance. The specific speed is also the main criteria for matching a specific hydro site with the correct turbine type. The specific speed is the speed with which the turbine turns for a particular discharge Q, with unit head and thereby is able to produce unit power.
Affinity laws Affinity Laws allow the output of a turbine to be predicted based on model tests. A miniature replica of a proposed design, about one foot (0.3 m) in diameter, can be tested and the laboratory measurements applied to the final application with high confidence. Affinity laws are derived by requiring similitude between the test model and the application. Flow through the turbine is controlled either by a large valve or by wicket gates arranged around the outside of the turbine runner. Differential head and flow can be plotted for a number of different values of gate opening, producing a hill diagram used to show the efficiency of the turbine at varying conditions.
Runaway speed The runaway speed of a water turbine is its speed at full flow, and no shaft load. The turbine will be designed to survive the mechanical forces of this speed. The manufacturer will supply the runaway speed rating.
Maintenance
A Francis turbine at the end of its life showingcavitation pitting, fatigue cracking and a catastrophic failure. Earlier repair jobs that used stainless steel weld rods are visible.
Turbines are designed to run for decades with very little maintenance of the main elements; overhaul intervals are on the order of several years. Maintenance of the runners and parts exposed to water include removal, inspection, and repair of worn parts. Normal wear and tear includes pitting from cavitation, fatigue cracking, and abrasion from suspended solids in the water. Steel elements are repaired by welding, usually with stainless steel rods. Damaged areas are cut or ground out, then welded back up to their original or an improved profile. Old turbine runners may have a significant amount of stainless steel added this way by the end of their lifetime. Elaborate welding procedures may be used to achieve the highest quality repairs.[4] Other elements requiring inspection and repair during overhauls include bearings, packing box and shaft sleeves, servomotors, cooling systems for the bearings and generator coils, seal rings, wicket gate linkage elements and all surfaces.[5]
Environmental impact Main article: Environmental impacts of reservoirs Water turbines are generally considered a clean power producer, as the turbine causes essentially no change to the water. They use a renewable energy source and are designed to operate for decades. They produce significant amounts of the world's electrical supply. Historically there have also been negative consequences, mostly associated with the dams normally required for power production. Dams alter the natural ecology of rivers, potentially killing fish, stopping migrations, and disrupting peoples' livelihoods. For example, American Indian tribes in the Pacific Northwest had livelihoods built around salmon fishing, but aggressive dam-building destroyed their way of life. Dams also cause less obvious, but potentially serious consequences, including increased evaporation of water (especially in arid
regions), build up of silt behind the dam, and changes to water temperature and flow patterns. Some people[who?] believe that it is possible to construct hydropower systems that divert fish and other organisms away from turbine intakes without significant damage or loss of power; historical performance of diversion structures have been poor. In the United States, it is now illegal to block the migration of fish, for example the endangered great white sturgeon in North America, so fish ladders must be provided by dam builders. The actual performance of fish ladders is often poor.[citation needed]
See also Wikimedia Commons has media related to: Water Turbines Sustainable development portal
Archimedes' screw
Banki turbine
Gorlov helical turbine
Hydroelectricity
Hydropower
Water wheel
References 1.
^
a b
Wilson 1995, pp. 507f.; Wikander 2000, p. 377; Donners, Waelkens &
Deckers 2002, p. 13 2.
^ W. A. Doble, The Tangential Water Wheel, Transactions of the American Institute of Mining Engineers, Vol. XXIX, 1899.
3.
^ W. F. Durrand, The Pelton Water Wheel, Stanford University, Mechanical Engineering, 1939.
4.
^ Cline, Roger:Mechanical Overhaul Procedures for Hydroelectric Units (Facilities Instructions, Standards, and Techniques, Volume 2-7); United States Department of the Interior Bureau of Reclamation, Denver, Colorado, July 1994 (800KB pdf).
5.
^ United States Department of the Interior Bureau of Reclamation; Duncan, William (revised April 1989): Turbine Repair (Facilities Instructions, Standards & Techniques, Volume 2-5) (1.5 MB pdf).
Sources
Donners, K.; Waelkens, M.; Deckers, J. (2002), "Water Mills in the Area of Sagalassos: A Disappearing Ancient Technology", Anatolian Studies 52: 1–17
Wikander, Örjan (2000), "The Water-Mill", in Wikander, Örjan, Handbook of Ancient Water Technology, Technology and Change in History, 2, Leiden: Brill, pp. 371–400, ISBN 90-04-11123-9
Wilson, Andrew (1995), "Water-Power in North Africa and the Development of the Horizontal Water-Wheel", Journal of Roman Archaeology 8: 499–510
External links
Introductory turbine math
European Union publication, Layman's hydropower handbook,12 MB pdf
"Selecting Hydraulic Reaction Turbines", US Bureau of Reclamation publication, 48 MB pdf
"Laboratory for hydraulique machines", Lausanne (Switzerland)
DoradoVista, Small Hydro Power Information [hide]v · d · eTopics related to Hydropower
Hydroelectricity · Head · Discharge · Dam · Francis turbine · Kaplan turbine · Tyson turbine · Gorlov helical turbine · Pelton wheel · Turgo turbine · Banki tur the-river · Low head · Small hydro · Micro hydro · Pico hydro
Categories: Water turbines
Log in / create account
Article Discussion Read View source View history
Main page Contents Featured content Current events Random article Donate to Wikipedia
Interaction
Help About Wikipedia Community portal Recent changes Contact Wikipedia
Toolbox Print/export Languages
ال عرب ية Български Català Česky Deutsch Eesti Español ف ار سی Français Hrvatski Bahasa Indonesia Italiano Magyar Nederlands 日本語 sk sk Polski
k y
sk
Português R â ă Simple English S ve šči a Suomi Svenska ไทย Tiế g Việt
This page was last modified on 20 July 2011 at 01:52.
Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. See Terms of use for details. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
Contact us
WATER TURBINES
urbines are basically fairly simple systems. They consist of the following components:
shaft - a tube that connects to the piping or penstock which brings the water into the turbine
FINDING THE B
One of the services want to provide our members is a listing ofRecommended
nozzle - a nozzle which shoots a jet of water (impulse type of turbines only) - a wheel which catches the water as it flows in causing the wheel to turn tor shaft - a steel shaft that connects the runner to the generator tor - a small electric generator that creates the electricity ve - a tube or shute that returns the water to the stream it came fro ouse - a small shed or enclosure to protect the water turbine and generator from the elements
e vs. Reaction Turbines
urbines are also often classified as being either impulse turbines or reactionturbines. In a reaction turbine the runners are mersed in water and are enclosed in a pressure casing. The runner blades are angled so that pressure differences across reate lift forces, like those on aircraft wings, and the lift forces cause the runner to rotate.
mpulse turbine the runner operates in air, and is turned by one or multiple jets of water which make contract with the A nozzle converts the pressurized low velocity water into a high speed jet much like you might use with a garden hose The nozzle is aligned so that it provides maximum force on the blades.
Microhydro Contrac you have used a microhydro contrac your home or busine and were happy wit their work please p us their contact info clicking here and w do the rest. As soon have a sufficient lis together we will pu it on the site. Than Editor
NEW PRODUC
of Turbines
re many kinds of micro hydro turbine designs. Typical microhydro generators have outputs of 10 kilowatts (kW) or less and nerate either DC or AC current depending upon the design. You will often hear water turbines referred to as either Pelton or urbines. These terms have to do with the structure of the water wheel inside the turbine.
Turbines
Pictured here is a Turgo style wheel. A Turgo turbine is an impulse type of turbine in which a jet of water the turbine blades. The structure of a Turgo wheel is much like that of airplane turbine in which the hub is surrounded by a f curved vanes. These vanes catch the water as it flows through the turbine causing the hub and shaft to turn. Turgo s are designed for higher speeds than Pelton turbines and usually have smaller diameters.
Turbines
A Pelton turbine is also an impulse turbine but in this type of turbine the hub is surrounded by a series or buckets which catch the water. The buckets are split into two halves so that the central area does not act as a dead spot ble of deflecting water away from the oncoming jet. The cutaway on the lower lips allows the following bucket to move before cutting off the jet propelling the bucket ahead of it. This also permits a smoother entrance of the bucket into the et.
Harris Water Turbin
The multiple nozzle arrangement allows more water to impa runner resulting in greater output at a head, and more usa power at lower hea Multi-nozzle system include a PVC penst and individual ball v on each nozzle. The pelton type runner wax cast of silicon bronze. The wheel 90% efficient, depe on nozzle size and h pressure. The bucke shape allows high efficiency for nozzl provides a flow rang over 100/1. $1640 f Harris Hydroelectric
WATER FACTBO
low Turbines
The use of hydroelectricity is growing. Today 6.6% the total electrical
generation of the U comes from hydro systems. In Canada of the energy come hyrdro.
A cross-flow turbine, also sometimes called a Michell-Banki turbine (from the name of the manufacturer) bine that uses a drum shaped runner much like the wheel on an old paddle wheel steamboat. A vertical rectangular nozzle with this type of turbine to drive a jet of water along the full length of the runner. One advantage of this type of turbine is can be used in situations where you have significant flow but not enough head pressure to use a high head turbine. Turbine
The Francis type of turbine is a reaction type of turbine in which the entire wheel assembly is immersed in water rounded by a pressure casing. In a Francis turbine the pressure casing is spiral shaped and is tapered to distribute water mly around the entire perimeter of the runner. It uses guide vanes to ensure that water is fed into the runners at the correct
er Turbine
A propeller turbine is just what its name implies. It uses a runner shaped just like a boat propeller to turn the or. The propeller usually has six vanes. A variation of the propeller turbine is the Kaplan turbine in which the pitch of the er blades is adjustable. This type of turbine is often used in large hydroelectric plants. An advantage of propeller type of s is that they can be used in very low head conditions provided there is enough flow.
ng the Best Type of Turbine
ype of water turbine is best for a particular situation often depends on the amount of head (water pressure) you will have in cation and whether you want to suspend the turbine in the water (reaction) or whether you want to use jets of water e). By looking at these factors together you can get some indication of what type of turbine design will work best:
se Turbine
High Head
Medium Head
Low Head
Pelton
cross-flow
cross-flow
ion Turbine
Turgo
multi-jet Pelton Turgo Francis
propeller Kaplan
Copyright © 2010 EnergyBible.com. All rights reserved.
