ORBITAL SHAKER ROTATOR MODEL: VRN-200, VRN-210 VRN-360, VRN-480
USER’S MANUAL MANUAL OPERATION / MAINTENANCE SERVICE and PARTS LIST
Safe! Inf"#$a%"n Your GEMMY SHAKER SHAKER has been designed with functions, reliability and safety in mind. This manual contains contains important operation operation and safety information, the user must carefully read r ead and understand the content of this manual prior to installing this euipment in conformance with your local
electrical codes.
Safe! Inf"#$a%"n Your GEMMY SHAKER has been designed with functions, reliability and safety in mind. This manual contains important operation and safety information, the user must carefully read and understand the content of this manual prior to installing this euipment in conformance with your local electrical codes.
C&a''%f%(a%"n
This !ater "ath is classified as #$lass %& euipment.
Sanda#d
This euipment complies with E$ Electromagnetic $ompatibility reuirement of E'()()%*%*+. E- filter is designed in conformity with /011( EE$*E$ 2irecti3e.
-S4/))% 5 %167
82A listed 9:SA; and <= 9
S)e(%f%(a%"n C"de
VRN-480
43erall dimension 1)) > 6)) > +%7
VRN-200
VRN-210
VRN-360
+/) > +/) > %?)
+%7 > +)) > %+7
+/) > 1+) > %/7
9mm; =latform
+? > 6%mm
+() > +()mm
+%7 > %?7mm
+? > 6%mm
Speed range
%) @ 6)) rpm
?7 @ +7) rpm
?7 @ +7) rpm
?7 > +7) rpm
4rbit diameter
%)mm
%)mm
%)mm
%)mm
Eccentric
+)mm
+)mm
+)mm
+)mm
oad at %)) rpm
+? Bg
?Bg
?Bg
?Bg
Speed readout
E2 digital
'A
'A
Tachometer
Eccentric number 1 sealed ball bearing
%
%
%
otor
"rush*less motor
2$+6C,
2$+6C, gear motor
2$+6C, gear motor
Timer
1 hours 5 H42
() minutes
() minutes
() minutes
8i>ed speed
'A
Yes, %))rpm
Yes, %))rpm
Yes, %))rpm
4peration mode
$ontinuous
$ontinuous
$ontinuous
$ontinuous
-ntermittent
-ntermittent
-ntermittent
-ntermittent
'A
'A
'A
diameter
4ption accessory 8lasB clamp
"attery 94ption;
'A
Yes %+C rechargeable
'A
Yes %+C rechargeable
Adaptor
'A
Yes
'A
Yes
4perating time
'A
1 hours
'A
1 hours
=ower
%%)C or ++)C
%%)C or ++)C
%%)C or ++)C
%%)C or ++)C
NOTE
The specifications are subDect to change without ad3anced notice.
C&a$)'
O#de#%n* %nf"#$a%"n VRN-480
$ode
8lasB
of flasB
Fty held
%+7ml
?%mm
%7 clamps
+7)ml
7mm
%% clamps
7))ml
%)?mm
( clamps
%
Inended +'e To pro3ide a desired gentle rotation to 3igorous agitation for mi>ing test solutions in micro*titration assays and for use in hematology, urology, or E-A0E-SA immunology within the range of %) @ 6)) rpm 9CR'*6); for mi>ing each test tube or well, flasB e3enly by the orbiting motion. Applications for Alpha, Kline, Mazzini, Syphills, Pregnancy and others. Refer to the clinic laboratory method specified by the reagent manufacturer or established by medical technology for products application.
In'a&&a%"n Remo3e the euipment carefully from the pacBing material, checB the electrical specifications located on side of the euipment. =lug cord into a properly grounded outlet.
ARNIN 2o not lift the euipment by pulling the platform out of the pacBing materials, there is possibility of damage to the euipment.
C"nen' Your GEMMY ShaBer CR'*6) containsG -
2etachable power $ord
%
-
=latform
%
-
$lamps for flasB 5 8astener
% 9 4ption ;
-
imited warranty sheet
%
O)%"na& a((e''"#! C&a$)'
O#de#%n* %nf"#$a%"n VRN-480
$ode
8lasB
of flasB
Fty held
%+7ml
?%mm
%7 clamps
+7)ml
7mm
%% clamps
7))ml
%)?mm
( clamps
+
OPERATION 1
$hecB the electrical specifications located on bacB of this euipment firstly. aBe sure the power specifications must meet your local codes.
2
=lug cord in a properly grounded receptacle.
3
=lace the testing specimen on to the platform properly. The te>tured non*slip rubber*foam mi>ing pad holds 3arious sies of printed well slides, culture plates, flasBs, micro plate, 3essels and test*tube racBs by means of friction.
4
VRN-480 !hen flasBs are used for operation, choice of 3arious sies of stainless steel clamps 9holders; for flasBs to meet your reuirement. Iust turn the screwdri3er to fasten the clamps into the platform properly. 8asteners are attached. -t does not need to remo3e the platform for screwing the flasBs holders
.
=ress the power switch to 4' position.
6
8eatures +*mode operations : #Timer& and #Switch& acti3ated rotation
1 VRN-480 Set time to your desired time for intermittent operation, or set time to H42 position for the continuous operation.
2 VRN-210, VRN-200, VRN-360 -
Switch power 488 and set your desired time by turning the control Bnob for the %ne#$%en rotation within the time set.
("n%n+"+' rotation.
-
Iust switch power on for the
-
8i>ed speed is optional by pressing the switch to # & position.
Set speed by turning the control Bnob clocBwise to your desired speed. The platform starts to rotate. CR'*6) and CR'*1() are euipped with the tachometer, read the speed directly from the tachometer. 'o speed indicator is mounted for CR'*+%) and CR'*+)), user is reuested to use the digital speed meter to set and monitor rotating speed.
8 10
!hen the time has elapsed, the platform stops automatically. Rechargeable battery is optional for CR'*+)) and CR'*1(). !hen the mains power supply is consumed, the battery will be charged automatically. 1 hours can be used from the full charge of battery. The adaptor is included for %+C battery input.
NOTE The platform configuration is fragile, Handle with $are. 2o not striBe the platform directly, or mo3e the unit by pulling the platform. 6
" " (a&%#ae 5e I7ED ')eed The recalibration of fi>ed speed is applied to CR'*+)), +%), 1() only. The euipment is initially calibrated the 8i>ed speed at %1)rpm in house, other 3alue of 8i>ed speed is calibrated as depicted belowG
=ress speed switch to #8-JE2& position
8ind a hold on bacB of the unit in which there is one screwdri3er*liBe adDuster 9CR;.
Turn CR clocBwise to achie3e a higher speed, or turn counterclocBwise to achie3e a lower speed.
Repeat this procedure and use tachometer to measure the speed of platform until it can meet your desired speed.
-f you cannot find a tachometer, use your finger to touch the platform slightly and count the rotation for one minute to get your desired speed.
Ma%nenan(e Se#9%(%n* %、
Always disconnect from power supply prior to maintenance ser3icing to a3oid electrical shocB. Refer to ser3icing to ualified personnel and licensed engineers.
+、
Always use a properly grounded electrical outlet of correct 3oltage and current handling.
1、
The dri3e motor and linBage assembly does not reuired lubrication.
6、
2o not remo3e euipment from carton bo> by pulling its platform. There is possibility to damage the euipment.
7、
Always refer to “Disassembly” for maintenance ser3icing.
(、
GEMMY will not assure any responsibility on persons who 3iolate the
regulations established abo3e.
?、
-n case of the spilt solution or specimen from the flasBs or 3essels, disconnect from the power supply immediately to a3oid the electrical shocB. 2isassemble the euipment and use cloth to clean the solution then dry the euipment by air. Heating dry is prohibited.
、
!hen the rubber*form pad is polluted by the spilt solution, remo3e the pad from the euipment and wearing late> glo3es to wash the rubber* form pad. 2ry the pad naturally by air. Heat dry is prohibited. TaBe care of the water treatment after cleaning.
/、
"rush*less motor is used. 2o not reuire change the carbon brushes.
%)、 4nce the rotating pi3ot is mo3able, adDust and position the pi3ot properly, rotate the platform until the rotating dri3e is smoothly, then glue it firmly.
7
D%'a''e$&! %、
Always disconnect from power supply prior to disassembly.
+、
2isassembly is limited to the ualified personnel and licensed engineers.
1、
oosen set*screw to remo3e control Bnob of speed controller and timer.
6、
oosen the screw to remo3e the eccentric pi3ot to remo3e the platform
7、
2isconnect wires from assembly prior to disassembly the electronic parts.
(、
The front controlled panel is glued
?、
The power switch and power cord outlet should be compressed on the sides from remo3al.
、
oosen the screws to remo3e the timer, speed tachometer and speed regulator.
T#"+&e'5""%n* P#"&e$
P"''%&e (a+'e
C"##e(%9e a(%"n
E##a%( ')eed
2efecti3e triac or =$"
Replace the new one
alfunctional CR
Replace the new one
oose pulley set
AdDust the pulley set
2efecti3e tachometer
Repair or replace new one
a%& " #"ae
2efecti3e circuit board
Repair or replace new one
2isengaged linBage
$onnect wiring
2efecti3e fuse
Replace the new one
2efecti3e motor
Replace the new one
2efecti3e ball bearings.
Replace the new one
oose eccentric pi3ot set
AdDust the eccentric set
oose pulley belt
Repair or adDust belt
Cann" +#n %$e#
oose fastener in Bnob
Screw fastener properly
"&ed #"a%"n
oose rotation pi3ot
AdDust the rotation pi3ot
a%& " f%; ')eed
2isconnected wiring
$onnect the wiring
Cann" #"ae
(
D%#e(%"n " (&ean: -
2isconnect from power supply prior to cleaning
-
$lean the euipment after e3ery use
-
:se a moist cleaning cloth to clean the case, platform
-
2ry the euipment thoroughly before use
-
'e3er use benine or paint thinner for cleaning
-
2o not immerse this euipment in water
T#an')"#a%"n -
8ragile, Handle !ith $are
-
2o not drop the euipment
-
2o not place this euipment upside down
-
2o not mo3e the euipment by pulling its platform
S"#a*e -
2o not place this euipment in draft, sunlight or near a piece of euipment, which emits heat as well as electromagnetic conduction emission.
-
2isconnect power supply when store this euipment
-
2o not place or store euipment where it can fall down easily
-
This euipment shall be stored under the condition of room temperature.
C"nd%%"n f"# #an')"#a%"n '"#a*e -
Temperature
: %)L$ @ 6)L$
-
Humidity
: 6)M * /)M
?
D%a*#a$ "f C"$)"nen' VRN-480
PARTS LIST 'o 2escription %
=latform
+
"ase, ball bearings 9:pper;
1
Eccentric
6
"ase, ball bearings 9ower;
Fty % % 1 %
7 $ircuit board, R=
%
(
$ase
%
?
=ulley wheel 9arge;
=ulley belt
/
=ulley wheel 9Small;
%) 8eet
% % % 6
%% %+ %1 %6 %7 %( %? % %/
otor Tachometer Speed regulator, CR Timer, mechanical 4'0488 switch $ontrol Bnob, timer $ontrol Bnob, CR Electrical outlet Sealed ball bearings
% % % % % % % % (
D%a*#a$ "f C"$)"nen' VRN-200, 210, 360
PARTS LIST 'o % + 1 6 7 ( ? / %) %% %+
2escription Rubber foam pad =latform Rotation pi3ot Aluminum racB "all bearing Eccentric "ase, ball bearing "ase, rotation pi3ot =late, eccentric pi3ot $ircuit board otor, gear motor, 2$ +6C Transformer
Fty % % 6 % % 6 % 6 % % % %
%1 %6 %7 %( %? % %/ +) +% ++ +1 +6
Rubber support Speed regulator, CR =ower cord $ontrol Bnob, speed regulator Housing 8eet $ontrol Bnob, timer 4'0488 switch Switch, fi>ed speed Timer, () minutes Tachometer, CR'*1() Housing, CR'*1()
6 % % % % 6 % % % % % %
/
%#%n* D%a*#a$ VRN-480
1 2 3 4 . 6 N N
+'e N
○
○
N
O O
T%$e#
O
RPM
○
N
N N
S ○
N
S)eed Dee("# 8 6 . 4 3 2 1
○
N
R%%
N-99333399-N
M""#
R%) N-33333333-N
A
<
SCR+)6
N
A
inesG P 1 "lue
<
P ( Red
N-33w33w3 3QN
P 7 !hite
VR20=
RPM Sen'"# Electronic =arts: $apacitor : %%7C (:8+7)C ++)C%.7:817)C Resistance: %%7C +1)C R%)
: +.+K 6.?K
R%%
: .+K +.+K
%)
%#%n* d%a*#a$: VRN-200, VRN-210, VRN-360
OFF
AC
Transformer ○
O V
○
○
110V
○
○
220V
Timer
ON
▌▌
○ A ○ C
24V
○ B ○ V
P.C.B.
P % Yellow P + Yellow
Fixed
○
○ R
○
○ T
○
○
>
○
M
%%
One ?ea# L%$%ed a##an! Your GEMMY product is guaranteed to be free from defects in materials and worBmanship for one 9%; year under normal use from the date of purchase. This WARRANY does not apply to any product damaged by accident, misuse, abuse or repaired by anyone other than the ualified ser3ice personnel. The liability of cludes the e>pendables and consumables. All warranty claims must be directed to the distributors or agents authoried by penses.
P@RCASE RECORD C"$)an! na$e Add#e''
P5"ne N" a; N" E$a%& add#e'' Dae "f )+#(5a'e P#"d+( $"de& Se#%a& N" D%'#%+"# Man+fa(+#e#:
E@ Re)#e'ena%9e
Gemmy !n"#s$rial %&rp'
A (EE s'a'
Ta%)e%, Ta%an
23 #+e de R"e#da$ 4000 L%e*e,
ISO001 ISO1348. MP DA %E