TNMS-M_hiT_7060_LCT_UserManual_3

s

Instructions TNMS-M SURPASS hiT 7060 3.1 LCT User Manual A42022-L5969-A 53-1-7619

User Manual

!

Instructions TNMS-M SURPAS SURPASS S hiT 7060 3.1 LCT

Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures. Systems with forced ventilation have rotating items. Non-observance of these conditions and the safety instructions can result in personal injury or in property damage. The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards. Mount the systems in areas with restricted access only. Only trained and qualified personnel may install, operate, and maintain the systems.

The same text in German: Wichtiger Hinweis zur Produktsicherheit In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Spannung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen. Anlagen mit Zwangsbelüftung haben drehende Teile. Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverletzungen und Sachschäden führen. Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen. Die Anlagen dürfen nur in Betriebsstätten mit beschränktem Zutritt aufgebaut werden. Die Anlagen dürfen nur durch geschultes und qualifiziertes Personal installiert, betrieben und gewartet werden.

Trademarks: All designations used in this document can be trademarks, the use of which by third parties for their own purposes could violate the rights of their owners.

Copyright (C) Siemens AG 2004 Issued by the Siemens Communications Hofmannstraße 51 D-81359 München Technical modifications possible. Technical specifications and features are binding only insofar as they are specifically and expressly agreed upon in a written contract.

2

A42022-L5969-A 53-1-7619

Instructions TNMS-M SURPASS hiT 7060 3.1 LCT

User Manual

Contents 1 1.1 1.2 1.3 1.3.1 1.3.2 1.3.3 1.4

Notes on this this Documentation ... ........................................................................ .....................................................................13 13 Customer Customer Documentation Documentation ... ............................................................................. ..........................................................................13 13 Complementary Documents.......................................................................... Documents..........................................................................13 13 Symbols Used in in the Customer Documentation ... ........................................... ........................................14 14 Symbol for Warnings..................................................................................... Warnings.....................................................................................14 14 Symbols for Notes......................................................................................... Notes.........................................................................................14 14 Symbols for Menu Displays and Text Inputs................................................. Inputs.................................................14 14 Notes on Licensed Software Software ... ......................................................................... ......................................................................14 14

2

Introduction.................................................................................................... Introduction....................................................................................................15 15

3

Features Features ... ........................................................................................................ .....................................................................................................16 16

4

Hardware Hardware Configurati Configuration on ... ................................................................................ .............................................................................18 18

5

Software Configuration.................................................................................. Configuration..................................................................................19 19

6 6.1 6.2 6.3

Installation Installation ... ..................................................................................................... ..................................................................................................20 20 Route Configuratio Configuration n ... ...................................................................................... ...................................................................................20 20 Installing the LCT software package............................................................. package.............................................................25 25 Uninstalling Uninstalling the LCT Software Software Package ... ....................................................... ....................................................31 31

7 7.1 7.2

Starting and Shutting down TNMS-M SURPASS SURPASS hiT 7060 LCT ... .................. ...............33 33 Starting TNMS-M SURPASS SURPASS hiT 7060 LCT ... ................................................. ..............................................33 33 Shutting Down TNMS-M SURPASS hiT 7060 LCT ... ...................................... ...................................33 33

8 8.1 8.1.1 8.1.2 8.1.3 8.2 8.2.1 8.2.2 8.2.3

Main Interface Interface Features ... ................................................................................ .............................................................................34 34 Main Window................................................................................................. Window.................................................................................................34 34 Title Bar Bar ... ......................................................................................................... ......................................................................................................34 34 Main Menu Bar.............................................................................................. Bar..............................................................................................34 34 Work Work Area ... ..................................................................................................... ..................................................................................................37 37 Submenus (with Right Mouse Button Click).................................................. Click)..................................................37 37 SDH Card...................................................................................................... Card......................................................................................................37 37 CC Card Card ... ........................................................................................................ .....................................................................................................37 37 Ethernet Ethernet Card ... ................................................................................................ .............................................................................................37 37

9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.9.1 9.9.2

NE Configuration and Management.............................................................. Management..............................................................38 38 Chassis View................................................................................................. View.................................................................................................38 38 Synchronizing NE.......................................................................................... NE..........................................................................................39 39 NE Property Configuration Configuration ... ............................................................................ .........................................................................40 40 Shutting Shutting down down NE ... ......................................................................................... ......................................................................................41 41 FTP Settings.................................................................................................. Settings..................................................................................................42 42 NE Software Management............................................................................ Management............................................................................43 43 MIB Management.......................................................................................... Management..........................................................................................44 44 NE Timing Timing Setting Setting ... ......................................................................................... ......................................................................................46 46 NE Trap Destination Configuratio Configuration n ... ............................................................... ............................................................47 47 Changing Changing NE NE IP IP ... ............................................................................................ .........................................................................................48 48 ChangIng Ethernet IP.................................................................................... IP....................................................................................48 48

A42022-L5969-A 53-1-7619

3

User Manual


LCT

4

10 10.1 10.1.1 10.1.2 10.1.3 10.2 10.2.1 10.2.2 10.3 10.4 10.5 10.5.1 10.5.2 10.5.3 10.6 10.6.1 10.6.2 10.7 10.7.1 10.7.2 10.7.3 10.7.4 10.8

SDH Configuration and Management ...........................................................50 Card Configuration and Management...........................................................50 SDH Card Configuration and Management ..................................................50 Synchronizing the Card.................................................................................51 Deleting Card ................................................................................................52 SDH Port Configuration and Management....................................................52 Port Configuration .........................................................................................52 Port Status.....................................................................................................53 E1 Ports Property Configuration ...................................................................53 OSI Configuration..........................................................................................55 CC Configuration and Management..............................................................56 Querying Current Cross-Connection.............................................................56 Adding a New Cross-Connection ..................................................................57 Deleting a Connection...................................................................................58 TP Configuration and Management ..............................................................58 Querying Current Terminal Point ..................................................................58 TP Multiplexing Structure ..............................................................................60 Synchronization Management.......................................................................62 Global Settings ..............................................................................................63 Configuring the Timing Source of NE............................................................64 Configuring the System Clock.......................................................................66 Configuring the Reference ............................................................................66 EOW Configuration .......................................................................................68

11 11.1 11.2 11.2.1 11.2.2 11.2.3 11.3 11.4 11.5 11.6 11.7 11.8

Ethernet Configuration and Management .....................................................69 Bridge Configuration......................................................................................69 LAN Card Configuration and Management...................................................69 LAN Port Properties ......................................................................................70 VLAN Rate Limiting .......................................................................................71 CoS Configuration .........................................................................................73 WAN Port Configuration................................................................................75 VLAN Management .......................................................................................76 Static MAC Address Configuration................................................................79 ACL Configuration .........................................................................................81 Group Broadcast Configuration.....................................................................82 RSTP Configuration ......................................................................................83

12 12.1 12.2 12.2.1 12.2.2 12.2.3 12.2.4 12.3 12.4 12.4.1 12.4.2

Protection Management ................................................................................85 CC 1+1 Protection.........................................................................................85 SNCP Management ......................................................................................85 Viewing and Modifying SNCP .......................................................................86 Creating SNCP..............................................................................................88 Deleting SNCP ..............................................................................................89 Switching SNCP ............................................................................................90 MSP Management.........................................................................................90 MSSPRING Management .............................................................................93 Creating MSSPRing ......................................................................................94 Modifying MSSPring......................................................................................97

A42022-L5969-A 53-1-7619


User Manual

12.4.3

Deleting MSSPRing ....................................................................................100

13 13.1 13.2 13.3 13.4 13.5 13.6 13.7

OSPFOSPF.................................................................................................101 OSPF General.............................................................................................101 OSPF Areas ................................................................................................103 OSPF Interfaces..........................................................................................105 OSPF Interface Metrics...............................................................................107 OSPF Neighbors .........................................................................................108 OSPF LSDB ................................................................................................109 OSPF Ext LSDB..........................................................................................110

14 14.1 14.1.1 14.1.2 14.2

Maintenance................................................................................................111 Loop-back Test Management .....................................................................111 Querying Loopback Status..........................................................................111 Setting Loopback Test ................................................................................111 LED Test .....................................................................................................112

15 15.1 15.1.1 15.1.2 15.2 15.2.1 15.2.2 15.2.3 15.2.4 15.3 15.3.1 15.3.2 15.3.3 15.3.4

Performance Monitoring Management........................................................113 Overview of Performance Monitoring..........................................................113 SDH Performance Monitoring .....................................................................113 Data Performance Monitoring Parameters .................................................116 SDH Performance Monitoring .....................................................................117 Filter Setting ................................................................................................118 Editing Monitored Parameter ......................................................................119 Alarm Threshold..........................................................................................120 History SDH Performance...........................................................................121 Ethernet Performance Monitoring Configuration.........................................122 Filter Setting ................................................................................................123 Editing Monitored Parameter ......................................................................124 Ethernet PM Thresholds .............................................................................125 History Ethernet Performance.....................................................................127

16 16.1 16.2 16.2.1 16.2.2 16.2.3 16.2.4 16.2.5 16.3 16.4 16.4.1 16.4.2 16.5 16.5.1 16.5.2 16.6 16.6.1

Alarm and Event Management....................................................................129 Overview of Alarms .....................................................................................129 NE Alarms ...................................................................................................129 Current Alarms ............................................................................................129 Viewing Active Alarms.................................................................................130 Reviewing the Current Alarms ....................................................................131 Viewing Alarm Detail...................................................................................131 Clearing Alarms...........................................................................................132 LED Indicators.............................................................................................132 Exporting Alarms.........................................................................................133 Exporting Active Alarms to a File ................................................................133 Printing Active Alarms.................................................................................135 Configure Fault Management......................................................................136 Audio Alarm Configuration ..........................................................................136 Alarm Type List Management .....................................................................137 Alarm Configuration for Single NE ..............................................................138 Alarm Inhibit Configuration..........................................................................138

A42022-L5969-A 53-1-7619

5

User Manual


LCT

6

16.6.2 16.6.3 16.7 16.7.1 16.7.2 16.7.3 16.7.4

Alarm Out Configuration..............................................................................139 MDI/MDO Configuration..............................................................................139 Displaying the Node Event Log...................................................................141 Interpreting the Node Event Log .................................................................142 Events Management ...................................................................................142 Hardware Events.........................................................................................142 Software Events ..........................................................................................143

17 17.1

Resource and Database Management .......................................................144 NE Usage Statistics.....................................................................................144

18 18.1 18.2 18.3 18.4 18.5 18.6 18.7 18.8

How To ........................................................................................................145 Creating a TU12 Cross-Connection between STM-4 and STM-4/1 ...........145 Creating a Bi-Direction Cross-Connection of TU12 from STM-4 OC to STM4/1 OC .........................................................................................................150 Creating Timing Synchronized Network......................................................155 Configure Layer 2 100Mbps Ethernet Service ............................................161 Configure 1G Transparent Transmission Ethernet Service ........................169 Monitoring One STM-16 Port Current Performance ...................................172 Creating Multiplex-Section Protection between Two NEs...........................175 Creating SNCP Between Two NEs Using Two Ports of MainBoard(STM-4)177

19

Abbreviation ................................................................................................181

20

Index............................................................................................................183

A42022-L5969-A 53-1-7619


User Manual

Illustrations Fig. 2.1 TNMS-M Series Products................................................................................15 Fig. 6.1 Open Hyper Terminal ......................................................................................20 Fig. 6.2 Hyper Terminal--Connection Description ........................................................21 Fig. 6.3 Hyper Terminal--Connect To...........................................................................21 Fig. 6.4 Hyper Terminal--COM1 Properties ..................................................................22 Fig. 6.5 CLI Window--Login..........................................................................................22 Fig. 6.6 Main Menu.......................................................................................................23 Fig. 6.7 User Table .......................................................................................................23 Fig. 6.8 Edit a Given User ............................................................................................24 Fig. 6.9 IP Address Configuration.................................................................................24 Fig. 6.10 Add Static Route Information ........................................................................25 Fig. 6.11 Setup Wizard Welcome Screen ....................................................................26 Fig. 6.12 Select Destination Location...........................................................................26 Fig. 6.13 Select Start Menu Folder...............................................................................27 Fig. 6.14 Select Additional Tasks .................................................................................27 Fig. 6.15 Ready to Install..............................................................................................28 Fig. 6.16 Installing ........................................................................................................28 Fig. 6.17 Exit Setup ......................................................................................................29 Fig. 6.18 Completing the Setup....................................................................................29 Fig. 6.19 TNMS-M SURPASS hiT 7060 LCT Desktop Icon.........................................29 Fig. 6.20 Start Menu .....................................................................................................30 Fig. 6.21 Input NE’s Login Information .........................................................................30 Fig. 6.22 LCT GUI ........................................................................................................31 Fig. 6.23 Uninstall TNMS-M SURPASS hiT 7060 LCT ................................................31 Fig. 6.24 Confirm Window for Uninstall ........................................................................31 Fig. 6.25 Uninstall Status..............................................................................................32 Fig. 6.26 Complete Uninstalling Process .....................................................................32 Fig. 7.1 TNMS-M SURPASS hiT 7060 LCT Main Window ..........................................33 Fig. 8.1 Main Window...................................................................................................34 Fig. 9.1 Chassis View...................................................................................................38 Fig. 9.2 Refresh Chassis ..............................................................................................39 Fig. 9.3 Synchronize NE...............................................................................................39 Fig. 9.4 NE Properties ..................................................................................................40 Fig. 9.5 Shutdown NE...................................................................................................41 Fig. 9.6 Shutdown Information......................................................................................42 Fig. 9.7 FTP Settings....................................................................................................42 Fig. 9.8 NE Software Management ..............................................................................43 Fig. 9.9 FTP Setting......................................................................................................44 Fig. 9.10 MIB Management ..........................................................................................45 Fig. 9.11 FTP Setting....................................................................................................45 Fig. 9.12 NE Time Settings...........................................................................................46 Fig. 9.13 NE Destination...............................................................................................47 Fig. 9.14 Confirmation for Delete..................................................................................47 Fig. 9.15 NE Communication Parameters Configure ...................................................48 Fig. 9.16 Change NE IP................................................................................................48 Fig. 9.17 Configure Ethernet IP....................................................................................48 Fig. 10.1 Card Properties .............................................................................................50 Fig. 10.2 Synchronize Card..........................................................................................51 Fig. 10.3 Port Properties...............................................................................................52

A42022-L5969-A 53-1-7619

7

User Manual


LCT

Fig. 10.4 Card Properties............................................................................................. 54 Fig. 10.5 E1 Port Properties ........................................................................................ 54 Fig. 10.6 OSI Configuration ......................................................................................... 55 Fig. 10.7 Cross-Connect Management........................................................................ 56 Fig. 10.8 Create Cross-Connect .................................................................................. 57 Fig. 10.9 Confirmation for deleting Cross-Connections............................................... 58 Fig. 10.10 TP Configuration (View 1 - As Presented) ................................................. 59 Fig. 10.11 TP Configuration (View 2 - Engaged)......................................................... 59 Fig. 10.12 TP Multiplexing Structure Query................................................................. 60 Fig. 10.13 TP Multiplexing Structure, View 1............................................................... 61 Fig. 10.14 TP Multiplexing Structure, View 2............................................................... 61 Fig. 10.15 Add Mapping............................................................................................... 62 Fig. 10.16 Synchronization Management .................................................................... 63 Fig. 10.17 Global Settings ........................................................................................... 63 Fig. 10.18 Station Clock Settings Reference Time IN ................................................. 64 Fig. 10.19 Station Clock Settings Reference Time Out............................................... 65 Fig. 10.20 Station Clock Settings Reference Time Out (Clock Out Reference).......... 65 Fig. 10.21 System Clock.............................................................................................. 66 Fig. 10.22 Timing Source Reference Properties ......................................................... 67 Fig. 10.23 EOW Config................................................................................................ 68 Fig. 11.1 Bridge Properties .......................................................................................... 69 Fig. 11.2 LAN Port Configuration................................................................................. 70 Fig. 11.3 Rate Limit Config .......................................................................................... 71 Fig. 11.4 VLAN Rate Limit Config................................................................................ 72 Fig. 11.5 Add VLAN Rate Limit.................................................................................... 72 Fig. 11.6 Change Cos.................................................................................................. 73 Fig. 11.7 VLAN+Port Cos Config................................................................................. 74 Fig. 11.8 Add VLAN Cos.............................................................................................. 74 Fig. 11.9 WAN Port Config .......................................................................................... 75 Fig. 11.10 Bandwidth Configuration ............................................................................ 76 Fig. 11.11 VLAN Management .................................................................................... 77 Fig. 11.12 Modify VLAN Based on VLAN .................................................................... 78 Fig. 11.13 Modify VLAN Based on Ports ..................................................................... 79 Fig. 11.14 Static MAC Address Configuration ............................................................. 80 Fig. 11.15 Add MAC Address ...................................................................................... 80 Fig. 11.16 ACL Config ................................................................................................. 81 Fig. 11.17 Add ACL...................................................................................................... 81 Fig. 11.18 Group Broadcast Configuration.................................................................. 82 Fig. 11.19 Add MAC Address ...................................................................................... 83 Fig. 11.20 RSTP Properties Configuration .................................................................. 84 Fig. 11.21 Port RSTP Configuration ............................................................................ 84 Fig. 12.1 CC 1+1 Protection ........................................................................................ 85 Fig. 12.2 SNCP Management...................................................................................... 86 Fig. 12.3 View/Modify SNCP ....................................................................................... 87 Fig. 12.4 Create Cross-Connect .................................................................................. 88 Fig. 12.5 Create SNCP ................................................................................................ 89 Fig. 12.6 Delete SNCP ................................................................................................ 89 Fig. 12.7 SNCP Switch ................................................................................................ 90 Fig. 12.8 MSP Management ........................................................................................ 90 Fig. 12.9 Searching Result of Multiplex Section Protection......................................... 91 Fig. 12.10 External Commands ................................................................................... 92

8

A42022-L5969-A 53-1-7619


User Manual

Fig. 12.11 Create Linear Multiplex Section Protection Group ......................................92 Fig. 12.12 MSSPRing Management.............................................................................93 Fig. 12.13 Set Ring Property ........................................................................................94 Fig. 12.14 Warning Window .........................................................................................94 Fig. 12.15 Set NEs in Ring ...........................................................................................95 Fig. 12.16 Set East and West Sides.............................................................................95 Fig. 12.17 Set Peer East and West Sides ....................................................................96 Fig. 12.18 Set NUT.......................................................................................................96 Fig. 12.19 Set WTR ......................................................................................................97 Fig. 12.20 MSSPRING List...........................................................................................97 Fig. 12.21 MSSPRing Details.......................................................................................98 Fig. 12.22 Command of MS SPRing ............................................................................98 Fig. 12.23 Advanced Configuration ..............................................................................99 Fig. 12.24 Delete MSSPRing......................................................................................100 Fig. 13.1 OSPF Submenu ..........................................................................................101 Fig. 13.2 OSPF General .............................................................................................102 Fig. 13.3 OSPF Area ..................................................................................................103 Fig. 13.4 Add OSPF Area...........................................................................................104 Fig. 13.5 Edit OSPF Area...........................................................................................105 Fig. 13.6 OPSF Interface............................................................................................105 Fig. 13.7 OSPF Interface Metric.................................................................................107 Fig. 13.8 OSPF Neighbor ...........................................................................................108 Fig. 13.9 OSPF Link State Database .........................................................................109 Fig. 13.10 OSPF External Link State Database .........................................................110 Fig. 14.1 Loopback Test.............................................................................................111 Fig. 14.2 Lookback Test Configure.............................................................................112 Fig. 14.3 LED Test......................................................................................................112 Fig. 15.1 SDH Current Performance ..........................................................................117 Fig. 15.2 Monitor Point Filter ......................................................................................118 Fig. 15.3 Select Terminal Point ..................................................................................119 Fig. 15.4 Edit Properties of Monitored Parameter......................................................119 Fig. 15.5 Alarm Threshold ..........................................................................................120 Fig. 15.6 SDH History Performance ...........................................................................122 Fig. 15.7 Ethernet Current Performance ....................................................................123 Fig. 15.8 Monitor Point Filter ......................................................................................123 Fig. 15.9 Select Port...................................................................................................124 Fig. 15.10 Edit Properties of Performance Monitor ....................................................124 Fig. 15.11 1 Second Ethernet Thresholds..................................................................125 Fig. 15.12 Monitor Point Filter ....................................................................................125 Fig. 15.13 Select Ports ...............................................................................................126 Fig. 15.14 Selected Ports ...........................................................................................126 Fig. 15.15 Edit Port Threshold....................................................................................127 Fig. 15.16 Ethernet History Performance ...................................................................127 Fig. 16.1 Chassis View with Open Current Alarms ....................................................130 Fig. 16.2 Fault, Active Alarms.....................................................................................130 Fig. 16.3 Alarm Count by Severity..............................................................................131 Fig. 16.4 Active Alarms...............................................................................................131 Fig. 16.5 Alarm Detail.................................................................................................132 Fig. 16.6 Clear Alarm..................................................................................................132 Fig. 16.7 Report Alarms..............................................................................................133 Fig. 16.8 Report Alarms Preview................................................................................134

A42022-L5969-A 53-1-7619

9

User Manual


LCT

Fig. 16.9 Save File..................................................................................................... 134 Fig. 16.10 Print Alarms .............................................................................................. 135 Fig. 16.11 Print Alarms Preview ................................................................................ 135 Fig. 16.12 Print Setup ................................................................................................ 136 Fig. 16.13 Audio Alarm Configuration........................................................................ 136 Fig. 16.14 Alarm Type List Management................................................................... 137 Fig. 16.15 Modify User Defined Severity of Alarm .................................................... 138 Fig. 16.16 Alarm Inhibit Configuration ....................................................................... 138 Fig. 16.17 Alarm Out Configuration ........................................................................... 139 Fig. 16.18 MDI Configuration..................................................................................... 140 Fig. 16.19 MDO Configuration ................................................................................... 141 Fig. 16.20 Node Event Log........................................................................................ 142 Fig. 17.1 Usage Statistics .......................................................................................... 144 Fig. 18.1 TP Multiplexing Structure ........................................................................... 145 Fig. 18.2 Query Result............................................................................................... 145 Fig. 18.3 Expanding Tree Graph ............................................................................... 146 Fig. 18.4 Mapping AU4 to TU12 ................................................................................ 146 Fig. 18.5 Result of Mapping....................................................................................... 147 Fig. 18.6 Mapping TU12 to AU4 ................................................................................ 147 Fig. 18.7 Cross-Connect Management Menu............................................................ 148 Fig. 18.8 Cross-Connect Management...................................................................... 148 Fig. 18.9 Create Cross-Connect ................................................................................ 149 Fig. 18.10 TP Multiplexing Structure ......................................................................... 150 Fig. 18.11 Query Result............................................................................................. 151 Fig. 18.12 Expanding Tree Graph ............................................................................. 151 Fig. 18.13 Mapping AU4 to TU12 .............................................................................. 152 Fig. 18.14 Result of Mapping..................................................................................... 152 Fig. 18.15 Mapping TU12 to AU4 .............................................................................. 153 Fig. 18.16 Cross-Connection Menu ........................................................................... 153 Fig. 18.17 Cross-Connect Management.................................................................... 154 Fig. 18.18 Create Cross-Connect .............................................................................. 154 Fig. 18.19 Create Cross-Connect .............................................................................. 155 Fig. 18.20 Three (3) Node Ring................................................................................. 156 Fig. 18.21 Synchronization Management .................................................................. 156 Fig. 18.22 Station Clock Setting ................................................................................ 157 Fig. 18.23 Timing Source Reference Properties ....................................................... 157 Fig. 18.24 Remove Timing Source Reference .......................................................... 158 Fig. 18.25 System Clock............................................................................................ 158 Fig. 18.26 Timing Results .......................................................................................... 159 Fig. 18.27 Synchronization Management .................................................................. 160 Fig. 18.28 Timing Source Reference Management................................................... 160 Fig. 18.29 Synchronization Management .................................................................. 161 Fig. 18.30 Bridge Configuration Tab.......................................................................... 162 Fig. 18.31 Bridges Properties .................................................................................... 162 Fig. 18.32 WAN Port Config ...................................................................................... 163 Fig. 18.33 Bandwidth Configuration .......................................................................... 164 Fig. 18.34 VLAN Management .................................................................................. 165 Fig. 18.35 VLAN Config ............................................................................................. 166 Fig. 18.36 VLAN Management: Query Result ........................................................... 167 Fig. 18.37 Create CrossConnect ............................................................................... 168 Fig. 18.38 CrossConnect Management ..................................................................... 169

10

A42022-L5969-A 53-1-7619


User Manual

Fig. 18.39 SURPASS hiT7060 Chassis View.............................................................169 Fig. 18.40 WAN Port Config .......................................................................................170 Fig. 18.41 Bandwidth Configuration ...........................................................................170 Fig. 18.42 Create Cross-Connect...............................................................................171 Fig. 18.43 Cross-Connect Management ....................................................................172 Fig. 18.44 Current SDH Performance Tab.................................................................172 Fig. 18.45 SDH Current Performance ........................................................................173 Fig. 18.46 Monitor Point Filter ....................................................................................173 Fig. 18.47 Select Terminal Point ................................................................................174 Fig. 18.48 Monitor Point Filter ....................................................................................174 Fig. 18.49 SDH Current Performance ........................................................................175 Fig. 18.50 Linear Multiplex Section Protection Group Management..........................176 Fig. 18.51 Create Linear Multiplex Section Protection Group ....................................176 Fig. 18.52 Linear Multiplex Section Protection Group Management..........................177 Fig. 18.53 SNCP Example..........................................................................................177 Fig. 18.54 SNCP Management...................................................................................178 Fig. 18.55 Create and Config SNCP ..........................................................................179 Fig. 18.56 SNCP Protection of NE A..........................................................................179 Fig. 18.57 SNCP Switch .............................................................................................180

A42022-L5969-A 53-1-7619

11

User Manual


LCT

Tables Tab. 3.1 Feature List .................................................................................................... 17 Tab. 4.1 Minimum Hardware Requirement of TNMS-M SURPASS hiT 7060 LCT..... 18 Tab. 8.1 Main Menu Bar .............................................................................................. 36 Tab. 9.1 NE Properties ................................................................................................ 41 Tab. 9.2 NE Software Management Window Field Description .................................. 43 Tab. 10.1 Card Identification ....................................................................................... 51 Tab. 10.2 Port Configuration ....................................................................................... 53 Tab. 10.3 Port Status................................................................................................... 53 Tab. 10.4 TP Management Parameters ...................................................................... 60 Tab. 10.5 Timing Source Management Time IN Window Parameters........................ 64 Tab. 12.1 SNCP Properties ......................................................................................... 87 Tab. 15.1 Regenerator Section SES threshold xx% (for BIP-8)................................ 114 Tab. 15.2 Defects Resulting in a Near-end Severely Errored Second...................... 114 Tab. 15.3 Defects resulting in a Far-end Severely Errored Second.......................... 114 Tab. 15.4 Multiplex Section SES threshold xx% (For BIP-1) .................................... 115 Tab. 15.5 Defects Resulting in a Near-end Severely Errored Second...................... 115 Tab. 15.6 Defects Resulting in a Far-end Severely Errored Second ........................ 116 Tab. 15.7 Path Overhead Section SES Threshold xx% (For BIP-2, BIP-8).............. 116 Tab. 15.8 PM Management Functions ...................................................................... 117 Tab. 15.9 Default Value and Value Range for a Fixed 15-minute Period ................. 121 Tab. 15.10 Default value and Value Range for a Fixed 24-hour Period ................... 121 Tab. 15.11 Primary Ethernet PM Function ................................................................ 122 Tab. 16.1 Active Alarms Information ........................................................................ 131 Tab. 16.2 LED Status ................................................................................................ 133 Tab. 16.3 Management Events ................................................................................. 142 Tab. 16.4 Hardware Events....................................................................................... 143 Tab. 16.5 Software Events ........................................................................................ 143

12

A42022-L5969-A 53-1-7619


User Manual

1 Notes on this Documentation 1.1

Customer Documentation The Customer Documentation of the SURPASS hiT 7060 comprises the following descriptions and manuals: •

i

i 1.2

Technical Manual The Technical Manual gives an overview of the application, performance features, interfaces, and functions of the TNMS-M SURPASS hiT 7060. It also contains the most important technical data.

The Technical Description does not contain any instructions to operate the product. •

Installation and Testing Guide The Installation and Test Manual ITMN contains instructions on mounting, connecting, and commissioning the TNMS-M SURPASS hiT 7060, and connecting and commissioning the LCT operating terminals.

•

Trouble Manual The Trouble Manual provides information about the alarm list TNMS-M SURPASS hiT 7060 supports and troubleshooting procedures.

•

TNMS-M SURPASS hiT 7060 LCT User Manual The LCT User Manual provides information about the LCT (features, configuration, installation, etc.) and how to operate, monitor, and maintain the TNMS-M SURPASS hiT 7060 using the Element Manager software (Application Software) running on the LCT.

Besides the LCT User Manual, the Online Help of the TNMS-M SURPASS hiT software is of high importance for the user.

Complementary Documents In addition to the TNMS-M SURPASS hiT 7060 customer documentation listed in Chapter 1.1, there is further documentation: •

TNMS-M SURPASS hiT 7060 Release Note This document identifies the specific version of the TNMS-M SURPASS hiT 7060 and provides information on HW, SW, LCT components and the limitations of the release as well as important notes concerning the customer documentation.

A42022-L5969-A 53-1-7619

13

User Manual


LCT

1.3 1.3.1 !

1.3.2

i

Symbols Used in the Customer Documentation Symbol for Warnings This symbol identifies notes which, if ignored, can result in personal injury or in permanent damage to the equipment.

Symbols for Notes This symbol identifies notes providing information which extends beyond the immediate context.

⇒

Denotes a point in the text which contains specific handling instructions.

Cross reference to other chapters in this manual or cross reference to other manuals.

Help Note on the online help system of the relevant application software concerned.

1.3.3

Symbols for Menu Displays and Text Inputs Menu options from pop-up menus or inputs to be made by the user (texts, commands) are displayed consecutively in their hierarchical sequence in pointed brackets: etc.

1.4

Notes on Licensed Software This documentation refers to software products which were taken over from other companies as licenses. Should problems arise, the user should contact Siemens AG as the licensee and not the relevant licenser.

14

A42022-L5969-A 53-1-7619


User Manual

2 Introduction TNMS-M series products are network management system which are used to manage and maintain MSTP network elements built by SURPASS hiT series products.

The TNMS-M series network management system products include TNMS-M LCT and TNMS-M. (See Fig. 2.1)

Fig. 2.1 TNMS-M Series Products

TNMS-M LCT (Local Craft Terminal) provides NE level TNMS-M based management function and GUI. One TNMS-M LCT application can only connect and manage one NE at one time. The interface between TNMS-M LCT and NE is SNMP based. Different type network element corresponds to different type LCT, which is mainly used for on-site management and maintenances.

TNMS-M SURPASS hiT 7060 LCT is an element management system of single NE, which is designed to provide comprehensive fault, configuration, performance management functions for the SURPASS hiT 7060 product line.

A42022-L5969-A 53-1-7619

15

User Manual


LCT

3 Features The main features of TNMS-M SURPASS hiT 7060 LCT features are listed in Tab. 3.1. Feature Java-Based User Interface

Description • •

•

Consistency and Data Synchronization

•

•

Network Element Control

•

•

•

Configuration Management

•

• •

• •

• • • • • • • • • •

Protection and Redundancy

•

• • • • •

16

Java-based user interface to connect NEs Provides Chassis View showing the front faceplate of the equipment Color-coded LEDs to indicate NE status Uploads data from the actual NE to update the management information of NE in the LCT Ensures all status and data in the LCT are consistent with the actual NE Enables NE software updates and download from the LCT Redundant images of the embedded software are stored in an NE, one active and one backup which can be switched and activated by LCT NE warm reboot and cold reboot can be controlled by LCT View/synchronize/delete/modify Circuit-pack attributes View/synchronize/modify port attributes TP configuration and management, including viewing/synchronizing/modifying TP attributes, TP multiplexing structure configuration SDH Cross-Connect configuration and management Timing configuration and management, including select timing reference for system clock, modify/view timing reference of NE’s system clock, and configure timing reference for station clock Virtual concatenation configuration and management LCAS configuration Ethernet VLAN configuration Ethernet Class of Service configuration Rapid spanning trees management Rate limiting configuration of Ethernet port Broadcast strom control Multicast management OSPF parameters configuration OSI-lite parameters configuration Supports Cross-Connect/Timing 1+1 protection management Supports Equipment Protection management for E1 Supports MS-SPRing protection management Supports MSP protection management Supports SNCP/I protection management Supports Ethernet RSTP protection management

A42022-L5969-A 53-1-7619


User Manual

Feature Performance Management

Description •

• •

Maintenance

• •

OSPF Fault Management

• •

•

•

Event Management Tab. 3.1 Feature List

A42022-L5969-A 53-1-7619

•

Supports monitored performance TPs and parameters selection. Supports current performance management Supports history performance management Loopback Configuration for testing LED test Supports OSPF parameters query and modification Collects, displays, and manages SURPASS hiT 7060 fault messages (including NE, card, port and TP related) Supports color coded alarms to indicate alarm severity level Supports active alarm synchronization Supports NE related event management

17

User Manual


LCT

4 Hardware Configuration The TNMS-M SURPASS hiT 7060 LCT software can run on the following Operating Systems: •

Windows XP Professional PC, Desktop or Laptop

The minimum hardware requirement of TNMS-M SURPASS hiT 7060 LCT is listed in Tab. 4.1. Configuration Windows-Based Computer

Hardware Requirement • • • • •

•

1.6 GHz Pentium-4 Processor 512M RAM 1 × 20GB Hard Disk TP Ethernet 10/100BASE-T Networking Port Graphic Card with 1024 × 768 resolution (75Hz refresh for Desktop; 60-Hz refresh for Notebook) Color Monitor (17’’ for Desktop; 14’’ TFT for Notebook)

Tab. 4.1 Minimum Hardware Requirement of TNMS-M SURPASS hiT 7060 LCT

18

A42022-L5969-A 53-1-7619


User Manual

5 Software Configuration The following operating system and software package are required to install and run the TNMS-M SUPASS hiT 7060 LCT. •

Windows XP Professional operating system

•

The TNMS-M SURPASS hiT 7060 LCT software

A42022-L5969-A 53-1-7619

19

User Manual


LCT

6 Installation 6.1

Route Configuration TNMS-M SURPASS hiT 7060 LCT manages NEs based on TCP/IP addresses. Therefore, the user must set a static route to enable the LCT system to find the NE. Before setting the route, ensure that the console port and the MGMT port of the user’s computer are connected with the peer ports of SURPASS hiT 7060.

i

TNMS-M SURPASS hiT 7060 LCT only supports NE management by the MGMT port.

1. Click →→→→ to open the window. (See Fig. 6.1)

Fig. 6.1 Open Hyper Terminal

20

A42022-L5969-A 53-1-7619


User Manual

2. In the window, enter the user name in the field and click .

Fig. 6.2 Hyper Terminal--Connection Description

3. In the window, choose (the computer’s connected console port) in the drop-down menu and click .

Fig. 6.3 Hyper Terminal--Connect To

A42022-L5969-A 53-1-7619

21

User Manual


LCT

4. In the window, click and click .

Fig. 6.4 Hyper Terminal--COM1 Terminal--COM1 Proper ties

5. Input a few and the CLI interface window will be shown. (See Fig. 6.5) The user name is and the password is none.

WELCOME TO LOGIN

NE Version Rel 2.0 Build 6.40 ______________________________________________________________

User name: root Password:

Fig. 6.5 CLI Window--Login

22

A42022-L5969-A 53-1-7619


User Manual

6. The
will be shown. (See Fig. 6.6) User: root Main Menu

2005-01-01 15:41:28

Node IP: Management Port IP Address: Management Port Subnetwork Mask:

192.168.16.15 192.168.12.15 255.255.255.0

Default Gateway for Management Port:

192.168.12.1

Telnet Login: Enabled

Please select the sub menu to configure the system, or select exit menu to disconnect from the system.

Please enter: (U)ser, (I)p address, telnet (L)ogin, (D)CC, (O)si, osp(F), (T)elnet, e(X)it Fig. 6.6 Main Menu

7. User Table Press ‘U’ from the
and the will be shown. (See Fig. 6.7). The user table enables the user to add/delete/modify the user information. User: root ** User Table ** 2005-01-01 15:37:52 User Name Password Timeout(m Access Le Online Logged In Last Acce op ****** 15 Operator false 0 0 root ****** 30 Administr true 56156 56156

Please enter: (G)oto, (R)ight, t(O)p, (D)own, (A)dd, dele(T)e, (E)dit, e(X)it Fig. 6.7 User Table

A42022-L5969-A 53-1-7619

23

User Manual


LCT

Press ‘E’ from the to edit a given user. User: root ** User Table **

User Name 1) Password 2) Timeout(min.) 3) Access Level Online Logged In Time Last Accessed 4) Access EMS 5) Access Craft Login Count

2005-01-01 15:38:30

root ****** 30 Administrative true 56156 56156 true true 1

Please enter: (1-5), (G)oto, t(O)p, (D)own, (A)dd, dele(T)e, (S)ummary, e(X)it Fig. 6.8 Edit a Given User 8. IP Address Configuration Press ‘I’ from the
to enter the window. (See Fig. 6.9) In this window, configure the node IP address, the management port IP address, the management port subnet mask, and the default gateway for the management port. The user can select 1 to 4 to configure the special IP address based on needs. User: root

IP Address Configuration

1) Node IP: 2) Management Port IP Address: 3) Management Port Subnetwork Mask: 4) Default Gateway for Management Port:

2005-01-01 15:48:09

192.168.16.15 192.168.12.15 255.255.255.0 192.168.12.1

Please enter (1-4) or e(X)it Fig. 6.9 IP Address Configuration

24

A42022-L5969-A 53-1-7619


User Manual

9. Click →→→ to open the window, and then use the command to enter the static route information. For example, enter to add the static route information into the user’s computer. (See Fig. 6.10)

Fig. 6.10 Add Static Route Information

6.2

Installing the LCT software package After selecting the SURPASS hiT serial products, Siemens post sales engineers and technical support technicians will help to complete selecting and installing hardware and software based on requirements. A TNMS-M SURPASS hiT 7060LCT installation CD will be provided. Install the LCT software package on the provided CD using the wizard mode on any qualified operating system.

To describe how to install the LCT software package, the following example is provided.

A42022-L5969-A 53-1-7619

25

User Manual


LCT

1. Double-click the icon of TNMS_M_SURPASS_hiT7060_R31_setup.exe. A welcome screen will be shown. (See Fig. 6.11) Then Click .

Fig. 6.11 Setup Wizard Welcome Screen

2.

Accept the default destination location, and click to continue. (See Fig. 6.12)

Note: The TNMS-M SURPASS hiT 7060 LCT software will be installed by default in the %SystemDrive%\Siemens\hiT7060 folder. (%SystemDrive% specifies the drive letter of the hard disk drive containing the Windows operating system.) For example: If Windows is installed in Drive C, the software will be installed in the C:\Siemens\hiT7060 folder.

Fig. 6.12 Select Destination Location

26

A42022-L5969-A 53-1-7619


3.

User Manual

Select the Start Menu folder location, and click to continue.

Fig. 6.13 Select Start Menu Folder

4. In the window, there are two options: A: and B: . The default option is A, and both options may be selected. Click after the selection.

Fig. 6.14 Select Additional Tasks

A42022-L5969-A 53-1-7619

27

User Manual


LCT

5. After reviewing installation choices, click to proceed or to go back to make changes.

Fig. 6.15 Ready to Install

6.

LCT will now be installed. (See Fig. 6.16)

Fig. 6.16 Installing

28

A42022-L5969-A 53-1-7619


User Manual

7. At any steps of 1-6 above, click , and Exit Setup hint window will pop-up. (See Fig. 6.17) Click to exit setup. Click to continue the installation.

Fig. 6.17 Exit Setup

8. Click to finish the installation. It is recommended that do not select the option .

Fig. 6.18 Completing the Setup

9. After completing the installation, if the is selected in the Additional Tasks window, an icon on desktop will be shown.

Fig. 6.19 TNMS-M SURPASS hiT 7060 LCT Desktop Icon

10. Click , and select , or other name typed in step 2 will be seen.

A42022-L5969-A 53-1-7619

29

User Manual


LCT

Fig. 6.20 Start Menu

11. Click the icon and the LCT program will start. During this process, a DOS window will be shown. Wait for a few seconds and a new window will be shown. (See Fig. 6.21) Input LCT’s Login Name, Password and NE’s Node IP Address which can be communicated with. Then click . Note: If the Network adapter of the computer has more than one IP addresses, the LCT program will ask the user to set IP address.

Fig. 6.21 Input NE’s Login Information

12. After successfully connecting to the NE, the following GUI will be shown. (See Fig. 6.22)

30

A42022-L5969-A 53-1-7619


User Manual

Fig. 6.22 LCT GUI

6.3

Uninstalling the LCT Software Package 1. Click , select , select , and click .

Fig. 6.23 Uninstall TNMS-M SURPASS hiT 7060 LCT

2.

Select to uninstall TNMS-M SURPASS hiT 7060 3.1 LCT. (See Fig. 6.24)

Fig. 6.24 Confirm Window for Uninstall

A42022-L5969-A 53-1-7619

31

User Manual


LCT

3: After is selected, an Uninstall Status window will be shown. (Fig. 6.25)

Fig. 6.25 Uninstall Status

4. After the uninstalling is complete, a confirm window box will be shown. Click to finish the uninstall process. Some items could not be removed automatically, but can be removed manually.

Fig. 6.26 Complete Uninstalling Process

32

A42022-L5969-A 53-1-7619


User Manual

7 Starting and Shutting down TNMS-M SURPASS hiT 7060 LCT 7.1

Starting TNMS-M SURPASS hiT 7060 LCT After the SURPASS hiT 7060 LCT software is installed, there are two ways to start TNMS-M SURPASS hiT 7060 LCT. Option 1:

Double-click the TNMS-M SURPASS hiT 7060 LCT shortcut on the Desktop;

Option 2:

Click → →.

This will show a login window. A login window will show. After a while, the main window will open. (See Fig. 7.1)

Fig. 7.1 TNMS-M SURPASS hiT 7060 LCT Main Window

7.2

Shutting Down TNMS-M SURPASS hiT 7060 LCT There are two ways to shut down TNMS-M SURPASS hiT 7060 LCT: Option 1:

Click the at top right of the TNMS-M SURPASS hiT 7060 LCT window.

Option 2:

From the main menu, click →.

A confirm window will be shown. Click to confirm the shutdown request.

A42022-L5969-A 53-1-7619

33

User Manual


LCT

8 Main Interface Features 8.1

Main Window The main window (See Fig. 8.1) consists of the following elements: •

Title Bar

•

Main Menu Bar

•

Work Area

Fig. 8.1 Main Window

8.1.1

Title Bar The title bar is located at the top of the main window (See Fig8.1) The title bar contains: Leftmost, a special window symbol. The type designation of the network element.

8.1.2

Main Menu Bar The main menu bar is located at the top of the main window, below the title bar (See Fig. 8.1). It contains the main menu.

i

The drop-down menu items will be changed when different object (for example: an NE, a card, or a port) is selected in chassis view.

Before the TNMS-M SURPASS hiT 7060 LCT is connected to the NE, the drop-down menu has only one button shown: , which has two functions: and .

34

A42022-L5969-A 53-1-7619


User Manual

Working with the software Allow t the TNMS-M SURPASS hiT 7060 LCT to connect with NE Close the main window of the NE application software, thus ending the session

System Connect Exit

i

After the TNMS-M SURPASS hiT 7060 LCT is connected to the NE, the main menu bar shows seven drop-down menus: , , , , , , and .

System Disconnect Change Password About Audio Alarm Config Exit

Working with the software Disconnect LCT from NE Change current password of LCT Show the information about TNMS-M SURPASS hiT 7060 LCT Manage all alarm audio, including melody type and play times Close the main window of the NE application software, thus ending the session

Configuration NE Property Configuration Card Property Configuration Warm Reboot NE Cold Reboot NE Shutdown NE SDH Port Property Configuration TP Configuration TP Multiplexing Structure Cross-Connection Management Synchronization Management NE Time Setting CC(Card) 1+1 Protection Equipment Protection Management SNCP Management MSP Management MSSPRing Management NE FTP Configuration NE Trap Destination Configure NE Software Management NE MIB management EOW Configuration Alarm Inhibit Configuration Alarm Out Configuration MDI/MDO Configuration

Working with the NE configuration View and modify the properties of NE

A42022-L5969-A 53-1-7619

View and modify the properties of Card Note: This menu item will only be shown when a card is selected Restart NE under the LCT system Restart NE Close NE safely View and modify the properties of SDH Port Note: This menu item will only be shown when an SDH Port is selected View and modify all TP Properties View and modify the construction of TPs Manage all cross- connections in the NE Set and manage the timing references Note: This menu item will not be shown when a card is selected Set time zone Create and manage CC 1+1 Protection Create and manage Equipment Prptection Create and manage SNCP Create and manage MSP Create and manage MSSPRing Set server address Show and manage all current manager IP addresses Update, backup, and switch NE software Manage NE database Manage EOW data Set system alarm Set system alarm Set MDI/MDO

35

User Manual


LCT

NE Resource Usage Statistics Refresh Chassis Change NE IP Change Ethernet IP OSI Configuration OSPF Synchronize Card

Fault Active Alarms Events Alarm Type List Management

View all the cards and ports and their usages View the latest state of NEs Change NE’s IP address Note: This menu item will not be shown when a card or a port is selected Change Ethernet IP address Note: This menu item will not be shown when a card or a port is selected Configure OSI Manage OSPF Synchronize a selected card Note: This menu item will only be shown when a card is selected Managing Alarm Display current alarm Display all events about the operation Note: This menu item will not be shown when a card or a port is selected Manage alarm type

Performance and Statistics Current SDH Performance History SDH Performance Current Ethernet Performance Ethernet PM Thresholds History Ethernet Performance

View the status of NE View and manage current SDH performance

Maintenance PRBS Test Management Loop-back Test Management AIS/RDI Insertion Test Management LED Test

Working with the maintenance test Query and set PRBS test Perform Loop-back test

Windows SURPASS hiT 7060 Chassis View Minimize All Maximize All

Select the view for the open windows List of all the currently-open windows; the selected window (in the foreground) is indicated by the tick Minimizes the opened windows Maximizes all windows

Help Online Help

Online help( in English) conforming to MS Windows Display the help topics in the form of the , , and Folders

View and manage history SDH performance View and manage current Ethernet performance Set Ethernet performance thresholds View and manage history Ethernet performance

Query and set AIS/RDI Insertion test Perform LED test

Tab. 8.1 Main Menu Bar

36

A42022-L5969-A 53-1-7619


8.1.3

User Manual

Work Area This range of the main window (See Fig. 8.1) shows all the windows which have just been opened. All windows within the work area can be opened or closed without the application software ending (function of Windows). In the Alarm Count area, all current alarm are collected and the number are listed by serious and category.

8.2

Submenus (with Right Mouse Button Click) The menu sequence which is described here depends on the selected card.

8.2.1

SDH Card After selecting the STM card, click right button.

Card Property Configuration Synchronize Card Active Alarms Cold Reboot Card

8.2.2

Open Card Properties window Open Synchronize window View and manage active alarms Restart card

CC Card After selecting the CC card, click right button.

Card Property Configuration Synchronize Card Active Alarms Cold Reboot Card Cross-Connect Management Synchronization Management

8.2.3

Open Card Properties window Open Synchronize window View and manage active alarms Restart card Open Cross Connection Management window Open Synchronization Management window

Ethernet Card After selecting the Ethernet card, click right button.

Card Property Configuration Synchronize Card Active Alarms Delete Card

A42022-L5969-A 53-1-7619

Open Card Properties window Open Synchronize window View and manage active alarms Delete Card

37

User Manual


LCT

9 NE Configuration and Management Before performing actions on the TNMS-M SURPASS hiT 7060 LCT, the LCT must be connected to an NE.

9.1

Chassis View When the TNMS-M SURPASS hiT 7060 LCT is connected to an NE, the NE Chassis View will be shown, which shows the real-time status of the NE. (See Fig. 9.1)

Fig. 9.1 Chassis View

For example, when the sixth card from the right side in Fig. 9.1 was pulled out, the red warning will be marked on the card as shown in Fig. 9.1. In this view, a total representation of the current node status will be shown, including a graphical view of all the slots, the card functions, the card types, the status of individual ports, the power status, and other NE functions. However, one cannot change any properties of this node in the chassis view. Only after opening the configuration window can one start to modify node properties. Right-click the chassis view and select in the pop-up menu (See Fig. 9.2) or select → to refresh the chassis view.

38

A42022-L5969-A 53-1-7619


User Manual

Fig. 9.2 Refresh Chassis

9.2

Synchronizing NE In order to synchronize the LCT database with the NE’s database, the user must synchronize the NE using the following steps listed below. Right-click the chassis view and select (See Fig. 9.2). The window will be shown (See Fig. 9.3)

Fig. 9.3 Synchronize NE

A42022-L5969-A 53-1-7619

39

User Manual


LCT

Select the content to synchronize, and click to start the synchronization process. If the synchronization process succeeds, a message box will be shown. Click to quit the current window. Click to launch the online help.

9.3

NE Property Configuration To open the window, two methods can be used: •

In the chassis view, right-click and select .

•

From the main menu, select →.

An window will be shown. (See Fig. 9.4)

Fig. 9.4 NE Properties

Each item in the window is described in the following table. (See Tab. 9.1) Item NE Label Serial Number Location System Mode Description

40

Description This is used to distinguish different nodes The serial number of this node configured by the manufacturer The physical position of this node in real-life The current system mode of this node (which one cannot modify from this window). The user uses this to field to input his/her own detailed description of this node

A42022-L5969-A 53-1-7619


Item Version Contact Date/Time Card List

User Manual

Description The hardware version of this node. The contact or owner of this node The current time on this node The simple information of all the cards on this node. The user can access the card configuration window by double-clicking the corresponding line in the table.

Tab. 9.1 NE Properties

i

The user can change properties of an NE, but modifications are only completed after the button has been clicked.

Click to refresh the information of the window. Click to confirm all the modifications and to close the window. If changing some of the properties, click the button to check the latest status of this node. Click to print the information of this node. Click to launch the online help.

9.4

Shutting down NE To shut down NE, select → from the main menu. (See Fig. 9.5)

Fig. 9.5 Shutdown NE

A42022-L5969-A 53-1-7619

41

User Manual


LCT

Fig. 9.6 Shutdown Information

Click to confirm shutting down this NE. (See Fig. 9.6) The NE that has been shut down will be offline.

9.5

FTP Settings The FTP Settings can get the latest software and data support from the server. To perform The FTP Settings enable the user to get the latest software and data support from the server. To perform NE software management, MIB management, and performance monitoring, the SNM FTP setting needs to be configured first as well as the FTP server. Use the following steps to apply FTP Settings: From the main menu, select →. The window will be shown with the current FTP settings. (See Fig. 9.7)

Fig. 9.7 FTP Settings

To modify the current configuration in the section: Input the FTP server’s IP address in the field. Input the FTP username in the field. Input the FTP user password in the field. To update the current configuration, click . Click to confirm the modification. Click to quit the window. All unsaved modifications will be lost. Click to launch the online help.

42

A42022-L5969-A 53-1-7619


i 9.6

User Manual

The configuration of the FTP server should be the same as the real FTP server settings. Generally, the LCT server and the FTP server are on the same physical machine.

NE Software Management Two software images can be stored in the TNMS-M SURPASS hiT 7060 LCT, an active image and a backup image. Using the LCT, the user can download a TNMS-M SURPASS hiT 7060 LCT software image to the NE as the backup version from the FTP server or the user may switch software images between active and backup versions. NE software management is done by the steps below: From the main menu, select →. The window will be shown. (See Fig. 9.8)

Fig. 9.8 NE Software Management

Each field in the window is described as follows. (See Tab. 9.2) Fields Active Software Version

Description The NE software version currently running

Backup Software Version

The backup NE software version

State of Last Command

The last command status

Tab. 9.2 NE Software Management Window Field Description

Click to open the window. (See Fig. 9.9)

A42022-L5969-A 53-1-7619

43

User Manual


LCT

Fig. 9.9 FTP Setting

In the window, choose the NE from the drop-down menu. Input the corresponding information in the , , and fields. Click to refresh the information. Click to confirm the modifications. Click to quit the window. All unsaved modifications will be lost. Click to launch the online help.

In the window, input the NE software file name on the FTP server in the field, and click to download the software image to the NE as the backup software version from the FTP server. To switch the software images between the active version and the backup version, click . Then click or to reboot the NE. Click to close the window. All the unsaved modifications will be lost. Click to refresh the information. Click to launch the online help.

i 9.7

Note: Make sure that the FTP server settings and the software image path are correctly configured before the operation is launched.

MIB Management The TNMS-M SURPASS hiT 7060 LCT MIB consists of the internal databases/files in the NE that store all the NE configuration and run status information. There are two versions of MIB files stored in the NE: one is the active version and another is a backup version, all the MIB management functions can be performed by using the LCT. Following the steps below to perform MIB management: From the main menu, select →. The window will be shown. (See Fig. 9.10)

44

A42022-L5969-A 53-1-7619


User Manual

Fig. 9.10 MIB Management

Click to open the window. (See Fig. 9.9)

Fig. 9.11 FTP Setting

In the window, choose the NE from the drop-down menu. Input the corresponding information in the , , and fields. Click to refresh the information. Click to confirm the modifications. Click to quit the window. All unsaved modifications will be lost. Click to launch the online help.

In the window, to upload the MIB files from the NE to the FTP server, input the directory in which the MIB files will be saved on the FTP server in the field, and then click . To download the MIB files from the FTP server to the NE, input the directory in which the MIB files exist in the field, and then click . To activate the backup MIB version, click . This operation will activate the backup MIB version.

A42022-L5969-A 53-1-7619

45

User Manual


LCT

The field shows the state of the last command. Click to get the value of State of Last Command field.

9.8

NE Timing Setting Open the corresponding chassis view. From the main menu, select →. An NE Time Settings window will be shown. (See Fig. 9.12)

Fig. 9.12 NE Time Settings

In the drop-down menu of , the protocol can be set or . In the drop-down menu of , select local time zone for NE. In the section, select the corresponding NE whose time will be modified. In the drop-down menu of , the current time can be viewed manually. Click to check the latest information on setting time. Click to confirm the modifications.

46

A42022-L5969-A 53-1-7619


User Manual

Click to quit the window, all the unsaved modifications will be lost. Click to launch the online help

9.9

NE Trap Destination Configuration Select → . An NE Destination Configuration window will be shown. (See Fig. 9.13)

Fig. 9.13 NE Destination

The function of each button is described as follows: Click to set a selection in the window. Click , a confirm window will be shown.(See Fig. 9.14) Click to update current NE Destination. Click to enter the window. (See Fig. 9.15) Click to quit the window without saving any modifications. Click to launch the online help.

Fig. 9.14 Confirmation for Delete

A42022-L5969-A 53-1-7619

47

User Manual


LCT

Fig. 9.15 NE Communication Parameters Configure

9.9.1

Changing NE IP To change NE IP address of an existing node: Select →

Right click NE and select in the pop-up menu. A new window will be shown. (See Fig. 9.16)

Fig. 9.16 Change NE IP Input the new IP information of the NE, including , and . Click to confirm the modifications, or select to quit this window.

9.9.2

ChangIng Ethernet IP Use one of the following two methods to change the Ethernet IP address of an existing node: •

Select , or

•

Right click the MGMT port and select in the popup menu. And the window will be shown. (See Fig. 9.17)

→

Fig. 9.17 Configure Ethernet IP

48

A42022-L5969-A 53-1-7619


User Manual

Input the new IP information of the NE, including and . Click to confirm the modifications, or select to quit this window.

A42022-L5969-A 53-1-7619

49

User Manual


LCT

10 SDH Configuration and Management 10.1

Card Configuration and Management In the chassis view, the card selected becomes framed in blue. There are two methods to open the card configuration window in chassis view: •

Right-click the card, select , or

•

From the main menu, select →.

A Card Properties window will be shown. (See Fig. 10.1)

10.1.1

SDH Card Configuration and Management A typical window for card properties is shown below:

Fig. 10.1 Card Properties

Each field in the window is described as follows. (See Tab. 10.1) Fields Slot Number Card Function

50

Description The slot this card has been plugged into. The function of the card. The function of the card will also be showed in the chassis view, on the right top corner of this card, and in a floating window box after the mouse has been pointing on the card for a while.

A42022-L5969-A 53-1-7619


Fields

User Manual

Card State Card Serial Number Card Label Boot Image Version

Description The type of the card, such as, STM-64, STM-16, STM-4, STM-1, UDC, GE, FE, MC, CC, etc. The current state of this card The serial number of this card This is used to distinguish different cards easily The version of the boot server

Boot Image Date Card Disable Hardware Version

The time, when the boot server started Select yes or no in the drop-down menu The version of this card.

Temperature Threshold

The threshold setting for the temperature alarm. When the temperature of this card is over the threshold, an alarm will be raised. When the temperature has fallen below the temperature clear threshold, the temperature alarm will be automatically cleared. The list of all ports on this card.

Card Type

Temperature Clear Threshold Port list Tab. 10.1 Card Identification

If any properties of a card have been modified, the button must be used to validate these changes. And only after clicking this button, will the modification be completed. When viewing the card options and not changing properties of the card, click to check the latest status of the card. Click to print the information on this card. Click to close the window. All the unsaved modifications will be lost. Click to launch the online help.

10.1.2

Synchronizing the Card Right-click the corresponding card in the chassis view and select . A synchronize card window will be shown. (See Fig. 10.2)

Fig. 10.2 Synchronize Card

Click to start the synchronization process. Click to cancel the synchronization process.

A42022-L5969-A 53-1-7619

51

User Manual


LCT

10.1.3

Deleting Card When the card has an absent status, right-click it. In the pop-up menu, select . Then click in the pop-up warning window to confirm the deletion command, or click to cancel this operation.

10.2

SDH Port Configuration and Management There are two ways to open the port configuration window: In the chassis view, choose the corresponding port. Right-click, and select . Open the port configuration in the card configuration window: double-click the line of the • port to view or configure in the . A Port Properties window will be shown. (See Fig. 10.3)

Fig. 10.3 Port Properties There are two parts in this window: and . Each parameter in this window is described below. Generally, users can only change some parameters in the Port Configuration part.

10.2.1

Port Configuration Fields Port Type Port Label

52

Descriptions This identifies the type of port A user can change this field to distinguish among ports

A42022-L5969-A 53-1-7619


Fields Port Mode

Port Admin Mode Auto Laser Shutdown Port DCC Mode

Port DCC Protocol

User Manual

Descriptions There are three modes: : The system decides the optimum mode for this port. : When an alarm is generated from this card, it will be automatically reported to the alarm management. : No matter how many alarms are generated from this card, none of them will be reported. There are two Port Admin Modes: (connected), or (unconnected) means the laser transmitter will shutdown automatically when the laser receiver detects loss of signal. DCC (Data Communication Channel) is a management and communication channel carried in the SDH frames. Choosing MS-DCC or RS-DCC means that the DCC has been launched, and Off means that DCC is shutdown or unavailable. There are three port DCC protocols can be chosen: HDLC, PPP, and OSI.

Tab. 10.2 Port Configuration

10.2.2

Port Status This section displays the SDH port current status. Fields Operating Status

Descriptions The port status whether it is under operation or not.

Laser Bias Current Received Laser Power

Value of the laser bias current Optical power received through this port. (If the power is low, for example less than -40dBm, the sensor will not show its real number but will show –40) Optical power transmitted out from this port. (If the power is low, for example less than -40dBm, the sensor will not show its real number but show -40) Temperature of the laser

Transmitted Laser Power Laser Temperature Tab. 10.3 Port Status

If any properties of the port have been changed, click to confirm them. Only after clicking this button have the modifications been completed. If no changes are planned as the card has been inspected, click to check the latest status of the port. Click to print the information of this port. Click to quit the window. All the unsaved modifications will be lost. Click to launch the online help.

10.3

E1 Ports Property Configuration Right-click the corresponding card and select , a window will be shown. (See Fig. 10.4)

A42022-L5969-A 53-1-7619

53

User Manual


LCT

Fig. 10.4 Card Properties Then double-click the row of the port to view or configure in the section. The window will be shown. (See Fig. 10.5)

Fig. 10.5 E1 Port Properties

– Can be set as auto, monitored, or non-monitored. − Can be set as Enabled, or Disabled. Click to check the real-time E1 port properties. Click to accept modifications in the window.

54

A42022-L5969-A 53-1-7619


User Manual

Click to confirm changes and quit the window. Click to quit this window without saving any modifications. Click to print the information of the E1 Port. Click to launch the online help.

10.4

OSI Configuration In the chassis view select one SDH port. From the main menu, select →. The window will be shown. (See Fig. 10.6)

Fig. 10.6 OSI Configuration

Select or in submenu according current NE’s position. Select or in dropdown. Input corresponding value in other items. The meaning of those parameters is listed below. : retransmissions timer. The unit is millisecond : maximum time allowed without frames being exchanged. The unit is second : maximum number of frame repetition : maximum number outstanding I-frames. Window size in AITS mode : timer interval. The unit is second. : time to live for a CLNP PDU : the local NSAP address : the destination NSAP address

A42022-L5969-A 53-1-7619

55

User Manual


LCT

: the source IP address : the destination IP address : the maximum long of frame. Click to check the real-time OSI properties. Click to accept modifications in the window. Click to confirm changes and quit the window. Click to quit the window without saving any modifications. Click to launch the online help.

10.5

CC Configuration and Management To manage all cross-connection in the NE, open the CrossConnect Management window, there are two methods to open this window: •

Select → in main window.

•

Select a Cross-connect device card in the chassis view, and select in right-click menu.

The window will be shown. (See Fig. 10.7)

Fig. 10.7 Cross-Connect Management

Use this window to query, add, or delete cross-connection.

10.5.1

Querying Current Cross-Connection Usually there are many Cross-Connections established within one NE. The TNMS-M SURPASS hiT 7060 LCT provides a method of easily viewing them by providing a Query function. Input querying parameters There are several selectable parameters to restrict the range of Cross-Connect, including (), (), , , , and .

56

A42022-L5969-A 53-1-7619


User Manual

Select these parameters from the drop-down menus to find the Cross-Connect of interest, i.e. the target Cross-Connect. After choosing a specific Source Card or Sink Card, manually choose the port to restrict the Cross-Connect to a more limited range. Input a specific Circuit ID to go to those Cross-Connections directly. Click to view all Cross-Connections which satisfy the chosen conditions. When the mouse moves to a Cross-Connection, the tool tips feature will be shown. Click to print the information. Click to launch the online help.

10.5.2

Adding a New Cross-Connection Click to add a Cross-Connection; the window will be shown. (See Fig. 10.8)

Fig. 10.8 Create Cross-Connect

Choose the Cards and Ports between which a Cross-Connection is to be created; all available TPs (See Fig. 10.8) will be listed. Click to sort the TPs in the list by tributary, and then button will be changed to . Click to sort the TPs in the list by timeslot, and then the button will be changed to . Choose the source and the destination TPs, and click .

A42022-L5969-A 53-1-7619

57

User Manual


LCT

The and buttons can only be used if two available ports have been selected. Click to confirm the addition without closing the window and allowing additional cross-connections to be made. Click to confirm the changes and close the window. Click to exit the window. Click to launch the online help.

10.5.3

Deleting a Connection In the window, cross-connections can be selectively deleted. Click , a warning window will be shown.

Fig. 10.9 Confirmation for deleting Cross-Connections

10.6 10.6.1

•

Click to confirm the deletion.

•

Click to cancel the deletion.

TP Configuration and Management Querying Current Terminal Point Select →. The window will be shown. (See Fig. 10.10)

58

A42022-L5969-A 53-1-7619


User Manual

Fig. 10.10 TP Configuration (View 1 - As Presented)

Select the and to be checked, or select All STM, UDC, ATM, and E1 Cards or All STM, VS TM, and E1 Ports to check all the TPs on cards and ports. Click to check the TPs. (See Fig. 10.11)

Fig. 10.11 TP Configuration (View 2 - Engaged)

A42022-L5969-A 53-1-7619

59

User Manual


LCT

Select and view the TP to be modified and make desired changes to TP properties. The properties of this TP will be showed in the right panel. Every parameter is described in the table below. Fields TP Alarm Mon TIM Enable TI Trans Mode TI Rec Mode

Descriptions Can be set as Monitored or Non-Monitored Can be set as permitted or prohibited Can be set as 16-byte, Fixed 1-byte, Provisioned 1-byte Can be set as 16-byte, Fixed 1-byte, or provisioned 1-byte

Transmitted TI Shows the transmitted TI Accepted TI Shows the accepted TI Expected TI Shows the expected TI, cannot be changed SL Enabled Can be set as Yes or No Transmitted SL Shows the transmitted SL Accepted SL Shows the accepted SL Expected SL Can be set to various values. DEO Enable Can be set as permitted or prohibited. DEO Threshold The value can be set between 10exp(-5) and 10exp(-9) EXC Enable Can be set as permitted or prohibited. EXC Threshold The value can be set between 10exp(-3) and 10exp(-5) Tab. 10.4 TP Management Parameters

If any TP properties have been changed, the button will be presented enabling its use. Only after clicking the button will the modifications be completed. Click to send the TP information to a file or a printer. Click to quit the window. All unsaved modifications will be lost. Click to launch the online help.

10.6.2

TP Multiplexing Structure To open TP mapping, select →. The window will be shown. (See Fig. 10.12)

Fig. 10.12 TP Multiplexing Structure Query

Select the corresponding Card and then Port. Then click to view the TP Multiplexing Structure for the selected port. (See Fig. 10.13)

60

A42022-L5969-A 53-1-7619


User Manual

Fig. 10.13 TP Multiplexing Structure, View 1

Click the circle with a horizontal line to expand the tree, Click the circle with the vertical line to collapse the tree. Use a right-click on the point and choose Expand to open only this branch or Expand All to open all the branches including the sub-branches. (See Fig. 10.14)

Fig. 10.14 TP Multiplexing Structure, View 2

The point color indicates its status: blue color indicates that this point is vacant and the brown color indicates it is occupied. If the TP is unused, it can be mapped by highlighting and right-clicking the point. (See Fig. 10.15)

A42022-L5969-A 53-1-7619

61

User Manual


LCT

Fig. 10.15 Add Mapping

After modifications of all the mappings are finished, click to confirm the modification. To check the real-time mapping information, click at anytime. Click to exit the window.

10.7

Synchronization Management The TNMS-M SURPASS hiT 7060 LCT supports four timing references: listed from Reference1 to Reference4. Each reference can be configured as an STM-N, TimeIN1, and TimeIN2. Each of the references has 4 levels of priority. •

Right-click the CC Card, and select , or

•

Select →


62

A42022-L5969-A 53-1-7619


User Manual

Fig. 10.16 Synchronization Management

10.7.1

Global Settings Click to open the Global Settings of the Synchronization Management. (See Fig. 10.17)

Fig. 10.17 Global Settings

Select an option in the drop-down menu. enables quality level available or not. Click to check the real-time status. Click to accept modifications. Click to quit the window without saving any modifications. Click to launch the online help.

A42022-L5969-A 53-1-7619

63

User Manual


LCT

10.7.2

Configuring the Timing Source of NE Click to open the window. (See Fig. 10.18) There are four I/O routes in one SURPASS hiT 7060, two ports and two ports. Switch between them by using two tabs. (See Fig. 10.18, Fig. 10.19, and Fig. 10.20)

Fig. 10.18 Station Clock Settings Reference Time IN

Every field is described in the table below: Fields Monitored Status Signal Type Sa bit

Descriptions Can be set as auto, monitored, or unmonitored Can be set as 2MHz, 2Mbit/s UnFramed, or 2Mbit/s Framed Can be set from Sa4-Sa8

Tab. 10.5 Timing Source Management Time IN Window Parameters

To prevent a loop automatically, check the box.

64

A42022-L5969-A 53-1-7619


User Manual

Fig. 10.19 Station Clock Settings Reference Time Out

Set the in the drop-down menu under the tab. The parameters include , , and . For the chosen single type, configure the output clock quality including, , and . The will change accordingly. In the tab (See Fig. 10.20), configure the reference clock.

Fig. 10.20 Station Clock Settings Reference Time Out (Clock Out Reference)

Click to accept modifications in each window. Click to check the real-time status. Click to quit the window without saving any modifications. Click to launch the online help.

A42022-L5969-A 53-1-7619

65

User Manual


LCT

10.7.3

Configuring the System Clock To configure the system clock, click . (See Fig. 10.16) The window will be shown. (See Fig. 10.21)

Fig. 10.21 System Clock

The Current Reference, The SystemClock State, and Last External Switch Request show the current timing status and configuration. The Operation Mode indicates the current operation mode of this NE, including: – When Synchronization Supply Units and SDH equipment clocks cannot access stored data, or have never had a reference input, they use their own internal clocks to generate the synchronization signal until the network is restored. – The clock has its frequency phase locked to an input reference signal. – When the quality of the synchronization inputs falls below accepted levels, Synchronization Supply Units and SDH equipment clocks first use stored data to control phase and frequency variations. Select one of the three options in the field, and then click to change the mode. When is selected, modify the and settings if or in has been selected. Click to confirm the changes. If the state is , the option will be grayed out. Click to quit the window. Click to launch the online help.

10.7.4

Configuring the Reference Use window (See Fig. 10.16) to configure the time reference. Double-click the corresponding time reference, and a window will be shown. (See Fig. 10.22)

66

A42022-L5969-A 53-1-7619


User Manual

Fig. 10.22 Timing Source Reference Properties

In the window, the current status of the selected timing source is shown. Check to keep the reference valid. Check to monitor the reference. Select the corresponding Priority from 1 (the highest priority) to 4 (the lowest priority). Select the in the drop-down menu; options include or modes. In the mode, the QL cannot be changed, while in the mode, the QL can be set to a given value. When setting the to Provisioning, select the desired quality level in the drop-down menu. The QL levels include: PRC (Primary Reference Clock): A reference frequency standard comprising an ensemble of PRS that provide a reference frequency signal compliant with ITU G.811 or ETSI EN 300 462-6-1. The free run accuracy of PRC must be 10-11. SSU-A (Quality Level - SSU Transit): One of the SSM codes. This indicates that the clock source is traceable to a transit node SSU and should be indicated using a '0100' code. SSU-B (Quality Level - SSU Local): One of the SSM codes. This indicates that the clock source is traceable to a local node SSU and should be indicated using a '1000' code. SEC (Quality Level – SEC): One of the SSM codes. This indicates that the clock source is traceable to an SEC and should be indicated using a '1011' code. DNU (Quality Level - Do Not Use): One of the SSM codes. Do Not Use for Synchronization code is used to prevent timing loops and is transmitted in the opposite direction on interfaces used to synchronize equipment’s clock denoted by <1111>. Click to confirm the modifications. Click to quit the window without saving.

A42022-L5969-A 53-1-7619

67

User Manual


LCT

10.8

EOW Configuration In chassis view, select → to set the Engineering Order Wire. The window will be shown. (See Fig. 10.23 )

Fig. 10.23 EOW Config

To disable EOW settings, click the box to the left of the corresponding Disable box. To enable the EOW, set the correct card, port, and channel. Click to check the latest information of EOW. Click to confirm the modifications. Click to quit the window. All unsaved modifications will be lost. Click to launch the online help. Click to print the information.

68

A42022-L5969-A 53-1-7619


User Manual

11 Ethernet Configuration and Management 11.1

Bridge Configuration Right-click the corresponding Ethernet card and select in pop-up menu. The window will be shown. (See Fig. 11.1)

Fig. 11.1 Bridge Properties

The panel can display the current NE, Card name, and the status of the bridge in corresponding items. Click the drop-down menu of to select one type of tag needed. Input a label to help identify this bridge. Below this window, there are two tables, which list all LAN and WAN ports. Click the tab to change the table between them. After selecting one port, double-click it to see more detail information about this port. Click to check the latest information. Click to confirm the modification without closing the window. Click to confirm the modification if the user wants this window closed. Click to quit the window. All unsaved changes will be lost. Click to print the information of the bridges properties. Click< Help> to launch the online help.

11.2

LAN Card Configuration and Management LAN card configuration and management is similar to SDH card configuration and management.

A42022-L5969-A 53-1-7619

69

User Manual


LCT

To open the window, follow the steps below: •

Select the corresponding Ethernet card.

To open the window without a specific port defined: •

Right-click the card, and select .

To open the window with a specific port defined: •

Select the corresponding port in the Ethernet card, right-click on it, and select .


Fig. 11.2 LAN Port Configuration

11.2.1

LAN Port Properties – Can be set as Auto, Monitor, or Non-Monitor. – Can be set as Up or Down. – Can be set as Detag or Tag. Choose to make the BRL available. In the section, if is selected in the field, the other three parameters will be grayed out. If is selected, set these three parameters manually. Click to check the latest information. Click to confirm the modification without closing the window.

70

A42022-L5969-A 53-1-7619


User Manual

Click to confirm the modification and close the window. Click to quit the window. All the unsaved changes will be lost. Click to launch the online help.

11.2.2

VLAN Rate Limiting In the window (See Fig. 11.2), choose in the section and then click . In the window, in the area, choose , then click the button. The window will be shown. (See Fig. 11.3)

Fig. 11.3 Rate Limit Config

In the field, or can be chosen. Choose , and input the Rate Limit in the box; the range is from 200k to 100M. Choose , and click the button. The window will be shown. (See Fig. 11.4) Click to confirm the modifications. Click to confirm the modifications and quit this window. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

A42022-L5969-A 53-1-7619

71

User Manual


LCT

Fig. 11.4 VLAN Rate Limit Config

All the VLAN Rate Limit information will be displayed in the window. Click to create a new VLAN Rate Limit. (See Fig. 11.5) Click to delete the selected VLAN Rate Limit. Click to modify the selected VLAN Rate Limit. Click to check the latest information. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

Fig. 11.5 Add VLAN Rate Limit

72

A42022-L5969-A 53-1-7619


User Manual

In the window, input the ID of VLAN in the field. In the dropdown menu, select the corresponding rate for this VLAN. And the rate can be set as: 256K, 512K, 1024K, and 2048K, 10M, 20M, 50M and 100M. The operator can also input other rate; the range is from 200k to 100M. Click to confirm the modifications and continue adding VLAN Rate Limit. Click to confirm the modifications and quit this window. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

11.2.3

CoS Configuration In the window (See Fig. 11.2), select in the field and the button will be available. Click the button and the window will be shown. (See Fig. 11.6)

Fig. 11.6 Change Cos In the field, or can be chosen. Choose , and set the corresponding rate in the drop-down menu. There are four classes can be set: , , , and . Choose , and click the button. The window will be shown. (See Fig. 11.4) Click to confirm the modifications. Click to confirm the modifications and quit this window. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

A42022-L5969-A 53-1-7619

73

User Manual


LCT

Fig. 11.7 VLAN+Port Cos Config

All the VLAN Cos information will be displayed in the window. Click to create a new VLAN Cos. (See Fig. 11.5) Click to delete the selected VLAN Cos. Click to modify the selected VLAN Cos. Click to check the latest information. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

Fig. 11.8 Add VLAN Cos

In the window, input the ID of VLAN in the field.

74

A42022-L5969-A 53-1-7619


User Manual

In the dropdown menu, select the corresponding rate for this VLAN. There are four classes can be set: , , , and . Click to confirm the modifications and continue adding VLAN Cos. Click to confirm the modifications and quit this window. Click to quit this window. All the unsaved modifications will be lost. Click to launch the online help.

11.3

WAN Port Configuration To configure WAN Ports, select the corresponding Ethernet card. Right-click the card and select , the window will be shown. (See Fig. 11.9)

Fig. 11.9 WAN Port Config

Select the port to modify in the drop-down menu. The settings of the and sections in this window are the same as that in the window. In the panel, enable or disable LCAS and then click for detailed settings. (See Fig. 11.10)

A42022-L5969-A 53-1-7619

75

User Manual


LCT

Fig. 11.10 Bandwidth Configuration

For example, to set bandwidth to 4Mb, choose VC12-1 and VC12-2 (Other AUGs can be chosen from the left table) by clicking <⇒>. Click to confirm the modification without closing the window. Click to confirm the modification with this window closed. Click to quit the window. All the unsaved changes will be lost. Click to launch the online help.

11.4

VLAN Management Select the corresponding Ethernet card, right-click, and select . A new window of will be shown. (See Fig. 11.11) In the section, fill in the conditions as needed.

76

A42022-L5969-A 53-1-7619


User Manual

Fig. 11.11 VLAN Management

Click , all VLANs based on the query conditions will show in the list. Choose one VLAN record, by clicking , a new window will be shown which will enable the VLAN record to be modified. (See Fig. 11.12) Click , to delete the VLAN selected. Click to quit the window without saving any modifications. Click to print the VLAN information. Click to launch the online help.

A42022-L5969-A 53-1-7619

77

User Manual


LCT

Fig. 11.12 Modify VLAN Based on VLAN

Use the tab to reset VLAN ID and VLAN Name, and to select ports. Click to set modifications in the window. Click to confirm changes and quit the window. Click to quit the window without saving any modifications. Click to launch the online help.

Use the tab to modify the VLAN List. (See Fig. 11.13)

78

A42022-L5969-A 53-1-7619


User Manual

Fig. 11.13 Modify VLAN Based on Ports

11.5

Static MAC Address Configuration To configure Static MAC Address, select the corresponding Ethernet card. Right-click and click . The window will be shown. (See Fig. 11.14) The VLAN Ids and Ports of all the MAC Addresses will be listed in this window.

A42022-L5969-A 53-1-7619

79

User Manual


LCT

Fig. 11.14 Static MAC Address Configuration

Select the corresponding MAC; click to delete existing MAC. To add a new MAC Address, click . An window will be shown. (See Fig. 11.15)

Fig. 11.15 Add MAC Address

Input the . Input the and select the corresponding port in the drop-down menu. Click to confirm the action and continue adding other MAC Address. Click to confirm the action and close the window. Click to quit the window, all unsaved modifications will be lost.

80

A42022-L5969-A 53-1-7619


User Manual

Click to launch the online help.

11.6

ACL Configuration ACL (Access Control List) is used to manage MAC can access the Ethernet. Select the corresponding Ethernet card, right-click, and select . A new window of will be shown. (See Fig. 11.16)

Fig. 11.16 ACL Config

Click , a new window will be shown and new ACL may be added in it. (See Fig. 11.17) Click , the chosen ACL will immediately be deleted. Click to quit the window without saving any modifications. Click to launch the online help.

Fig. 11.17 Add ACL

A42022-L5969-A 53-1-7619

81

User Manual


LCT

11.7

Group Broadcast Configuration To configure Group Broadcast, select the corresponding Ethernet card. Right-click, and select . The window will be shown. All MAC Addresses and Port Settings will be listed in this window. (See Fig. 11.18)

Fig. 11.18 Group Broadcast Configuration

To delete a MAC Address, select the corresponding MAC and click . To add a new MAC Address, click . A new window will be shown. (See Fig. 11.19)

82

A42022-L5969-A 53-1-7619


User Manual

Fig. 11.19 Add MAC Address

Input the MAC Address. Select the port in the panel, and click the <> button, to add it to the window will be shown.

Step 4: Select #LC5<1×STM-16(Line)> in the Card item, P01 in the Port item, and All in the TP Type. And then click ; all selected TPs will be listed. To monitor only one TP type, select the corresponding type in this item. Choose TPs to be monitored and click to complete TP selection.

A42022-L5969-A 53-1-7619

173

User Manual


LCT

Fig. 18.47 Select Terminal Point

Step 5: Select parameters to monitor, and click . The current performance of Port01 of STM-16 will be listed.

Fig. 18.48 Monitor Point Filter

174

A42022-L5969-A 53-1-7619


User Manual

Fig. 18.49 SDH Current Performance

Click , to monitor the latest performance of this port.

18.7

Creating Multiplex-Section Protection between Two NEs In linear Multiplex Section Protection (MSP), there are two integer physical paths between two multiplexes. Working section and protection section between multiplexes is connected using different optical interfaces. TNMS-M SURPASS hiT 7060 supports MSP protection at STM-4 and STM-1.

NE-A

NE-B

Fig 18.1 Point-to-point System

Fig 18.1 illustrates a point-to-point system between NE-A and NE-B. The working signal is transmitted through a pair of STM-4 ports while the protection signal is transmitted through another pair of STM-4 ports. To implement transmission protection, first the protection groups should be established in the NE to realize connection between the working path and the protection path. Step1: Select → from the main menu, the window will be shown. (See Fig. 18.50)

A42022-L5969-A 53-1-7619

175

User Manual


LCT

Fig. 18.50 Linear Multiplex Section Protection Group Management

Stpe2: Click , the window will be shown (See Fig. 18.51). Fill out the Protection Properties section. The Protection Group Label provides a name for the protection group (for example in Fig. 18.51); The can be selected as or ; The can be selected as or with the time between 0-720 seconds; Select #LC8<4×STM-4/1(Line)> and P01 in the Working Multiplex Section. The System will fill out the Protection Multiplex Section with #LC8<4×STM-4/1(Line)> and P02 automatically.

Fig. 18.51 Create Linear Multiplex Section Protection Group

Step3: Click to finish creating MSP, and created protection groups will appear in the window, double-click this protection group to see the detail information.

176

A42022-L5969-A 53-1-7619


User Manual

Fig. 18.52 Linear Multiplex Section Protection Group Management

18.8

Creating SNCP Between Two NEs Using Two Ports of MainBoard(STM-4) Sub-Network Connection Protection (SNCP) provides protection at VC-4-Xv/VC-3-Xv/ VC12-Xv levels. In the transmission end, service is bridged to two output ports; the two signals are transmitted to the destination via different routes. One is main channel and another is backup channel. In the receiving end, the NE selects a better signal from the two coming signals. When the main channel is failed, the system will switch to the protection channel to receive the signal. To describe how to configure SNCP protection, an example of a four nodes ring as shown in Fig. 18.53. Assume that a VC-4 connection between NE-A and NE-C needs to be established. The working channel is from NE-A, NE-B, to NE-C. The protection channel is from NE-A, NE-D, to NE-C.

Fig. 18.53 SNCP Example

A42022-L5969-A 53-1-7619

177

User Manual


LCT

To implement the SNCP, configure each NE as follows: To create a bi-directional VC-4 level cross-connection between a STM-1 unit port and a certain AU4 of LC2 port of NE-A. To create a bi-directional VC-4 level cross-connection between the first AU4 of LC1 port and the first AU4 of LC2 port of NE-D. Create a bi-directional cross-connection on the level of VC-4 between a certain STM-1 unit port and the first AU4 of LC1 port of NE-C.

Using NE-A as an example, a way to create SNCP protection group using TNMS-M SURPASS hiT 7060 LCT will be shown next: Step1: Select → from the main menu, the window will be shown. (See Fig. 18.54)

Fig. 18.54 SNCP Management

Step2: Click , and the window will be shown. (See Fig. 18.55) Click the drop-down menu of Capacity to select VC-4; Select bi-directional in service Direction; Set in Restore Mode;

Set the parameters in the Working TP section as: Working Card:

#LC2<1×STM-16(Line)>

Working Port:

P01

By Time Slot:

AU4 (#02)

In fact, the working TP is the slot of the cross-connection line port of working channel in NEA. Set the parameters in the Protection TP section as:

178

A42022-L5969-A 53-1-7619


User Manual

Protecting Card:

#LC7<4× STM-4/1(Line)>

Protecting Port:

P03

By Time Slot:

AU4 (#01)

Fig. 18.55 Create and Config SNCP

Step3: Click , the SNCP is created successfully. For NE-A, the original bi-direction cross-connect provides the channel protection function as the following: NE-A sends the signal to both line ports LC1 and LC2 simultaneously and selects the better one from the two received signals from LC1 and LC2. (See Fig. 18.56)

Fig. 18.56 SNCP Protection of NE A

NOTE: The way to create channel protection of NE-C is the same as that in NE-A, the difference is the working TP and protection TP is opposite to those of NE-A.

A42022-L5969-A 53-1-7619

179

User Manual


LCT

After creation of SNCP protection group, click in Fig. 18.54 to view the existed SNCP protection group. Select the corresponding protection group, and click . The window will be shown (See Fig. 18.57). In this window the condition of the current protection group is known. Meantime, operation of protection switch of SNCP protection group is done manually by clicking .

Fig. 18.57 SNCP Switch

: This command clears all commands that have been started and the recovery time of the operated NE : Protection switching will be closed, and the working channel will take on the service. Even if there is malfunction, switching will not happen. : Users switch services to protection channel by force even if there is fault on this channel. If the force switch requirement is not cleared, automatic switching will not happen. : User will switch service to working channel by force even if there is fault on this channel. If the force switch requirement is not cleared, automatic switching will not happen. : Users switch services to protection channel manually on the condition that there is no fault on this channel. Automatic switching is still in effect. : Users switch services to working channel manually on the condition that there is no fault on this channel. Automatic switching is still in effect.

180

A42022-L5969-A 53-1-7619


User Manual

19 Abbreviation ACL AIS ATM AU BBE CC CLI CoS CSES DCC DEG EM EOW EQP ES EXC FC FE FOP GE GFP HP IOP LAN LCAS LCD LB LOC LOM LOP LOS LP MS MS-SPRing MSP MSTP NE NPJC OCD OFS OOP PDH

A42022-L5969-A 53-1-7619

Access Control List Alarm Indication Signal Asynchronous Transfer Mode Administration Unit Background Block Error Cross-Connect Command Line Interface Class of Service Continuous Severely Errored Second Data Communication Channel Degraded Element Management Ethernet over WDM Equipped Errored Second Excessive error Fault Count Fast Ethernet, Far End Failure of Protocol Gigabit Ethernet General Framing Procedure High Path Input Optical Power Local Area Network Link Capacity Adjustment Scheme Loss of Cell Delineation Laser Bias Loss Of Continuity Loss of Multiframe Loss of Pointer Loss of Signal Low Path Multiplex Section Multiplex Section Shared Protection Ring Multiplex Section Protection Multi-Service Transport Platform Near End Negative Pointer Justification Count Out of Cell Delineation Out of Frame Second Output Optical Power Plesiochronous Digital Hierarchy

181

User Manual


LCT

PJCN PLM PPI PPJC QoS RDI RS SDH SECB SES SNMP SPI TCA TDM TIM TLS TP TU UAS UNEQ VC VPN

182

Pointer Change Negative Payload Mismatch PDH Physical Interface Positive Pointer Justification Count Quality of Service Remote Defect Indication Regenerator Section Synchronous Digital Hierarchy Severely Error Cell Block Severely Errored Second Simple Network Management Protocol SDH Physical Interface Threshold Crossing Alert Time Division Multiplexing Trace Identification Mismatch Transparent LAN Service Termination Point Tributary Unit Un-Available Second Unequipped Virtual Concatenation Virtual Private Network

A42022-L5969-A 53-1-7619


User Manual

20 Index A

M

ACL (Access Control List), 81 ACL Configuration, 81 Add Cross-Connection, 57 Alarm Alarm Configuration, 138 Clearing Alarms, 132 Alarm, 129 Viewing Active Alarms, 130

Main Window, 34 Maintenance, 111 MIB Management, 44 MSSPRING, 93

C Card Configuration and Management, 50 CC 1+1 Protection, 85 CC Configuration and Management, 56

D

N NE IP, 48 NE Property Configuration, 40 NE Software Management, 43 NE Usage Statistics, 144 Node Event Log, 141

O OSI Configuration, 55 OSPF, 101

Deleting Connection, 58

E EOW Configuration, 68 Ethernet Configuration and Management, 69 Ethernet IP, 48

P Performance Monitoring, 113

R RSTP Configuration, 83

F Fault Management, 136 FTP Settings, 42

S

Hardware Configuration, 18

SDH Port Configuration and Management, 52 Shut Down LCT, 33 Shutdown NE, 41 SNCP, 85 Software Configuration, 19 Start LCT, 33 Static MAC Address, 79 Synchronization Management, 62 Synchronize, 39

I

T

Install LCT software package, 25

Timing Setting, 46 TP Configuration and Management, 58

G Group Broadcast, 82

H

L LAN Card Configuration, 69 LED Indicators, 132 LED Test, 112 Linear Multiplex Section Group Protection, 90 Loop-back Test, 111

U Uninstall LCT Software Package, 31

V VLAN Management, 76

A42022-L5969-A 53-1-7619

183

TNMS-M_hiT_7060_LCT_UserManual_3

Recommend Documents