STEP KONFIGURASI MSAN
IPMB : CONFIGURE SYSNAME, MANAGEMENT, ROUTING AND BOARD CONFIRM : 1. CREATE SYSNAME 2. MANAGEMENT CONFIGURATION (VLAN, INTERFACE, IP ADDRESS, AND PORT, STATIC ROUTING) 3. CONFIGURE SNMP 4. CREATE USERNAME 5. CONFIRM BOARD ADDING INTENET-BROADBAND SERVICE : 6. CONFIGURE VLAN BROADBAND (VLAN SMART, AND PORT) 7. CONFIGURE TRAFFIC TABLE 8. CONFIGURE MULTI-SERVICE-PORT 9. CONFIGURE ADSL LINE-PROFILE 10. IN ADSL PORT DEACTIVATE AND ACTIVATE WITH NEW LINE PROFILE ADDING VoBB-VOICE OVER BROADBAND SERVICE DiSesuai dengan Permintaan Telkom, Configurasi sama seperti CONFIGURASI BROADBAND ALLOW VLAN H.248 and MEDIA : 11. INTERFACE CONFIGURATION FOR H.248 DAN VOICE MEDIA (VLAN, AND PORT) CONFIGURE EMU : 12. CONFIGURE EMU
PVMB : CONFIGURE SYSNAME, MANAGEMENT, ADD FRAME/BOARD, BOARD CONFIRM : 1. CREATE SYSNAME 2. MANAGEMENT CONFIGURATION (IN THE INTERFACE ETH MODIFY IP ADDRESS, SUBMASK, GW, AND VLAN) 3. CONFIGURE SNMP 4. CONFIGURE WORKING MODE
5. CREATE USERNAME 6. ADD FRAME, BOARD, AND THEN BOARD CONFIRM CREAT VLAN H.248 and MEDIA : 7. CONFIGURE H.248 AND VOICE MEDIA (IN THE INTERFACE ETH ADD IP ADDRESS, SUBMASK, GW, AND VLAN) 8. CONFIGURE QoS FOR H.248 AND VOICE MEDIA CONFIGURE INTERFACE VLAN H.248 and MEDIA : 9. CONFIGURE IF-H.248 (USE IP MG, UDP PORT, IP MEDIA, IP SOFTSWITCH, NEGOTIATION AND MG NAME) 10. CONFIGUR TID TID TEMPLATE FOR ZTE AND TID FORMAT RTP FOR NSN) 11. RESET COLDSTART CONFIGURE ESLUSER : 12. CONFIGURE ESL USER (USE INNER DIGIT MAP) CONFIGURE STAND ALONE : 13. CONFIGURE EMERGENCY CALL
MANAGEMENT, NMS, and IPMD (Broadband Control Board) (Untuk Data IPMD MSAN, Perhatikan data pada BROADBAND masing2 DIVRE, dari File Excel MSAN)
NMS connection to N2000 BMS sysname “MSAN00-(DIVRE)-(DATEL)-(MSAN-Vendor)” Contoh Penggunaan : MSAN HUAWEI Outdoor FRK pada Area Divre-7 Datel Bali Maka akan menjadi sysname MSAN00-D7-BLI-2FRK Catatan : untuk No MSAN Vendor ; 1.NSN 2.HUAWEI 3.ZTE Vlan 23 standard port vlan 23 0/2 0,6-7 interface vlanif 23 ip address 172.29.180.13
quit ip route-static 0.0.0.0 0.0.0.0 172.29.180.1 snmp-agent community read public snmp-agent community write private snmp-agent target-host trap address 172.29.128.4 securityname huawei v2c snmp-agent target-host trap address 172.29.128.5 securityname huawei v2c snmp-agent trap enable standard snmp-agent trap source vlanif 23 Create additional admin user on IPMD board Command:
terminal user name
User Name(length<6,15>):admin The user name must be equal to or more than 6 characters User Name(length<6,15>):admin The user name must be equal to or more than 6 characters User Name(length<6,15>):admin123 User Password(length<8,15>): r00tw3rk#@! Confirm Password(length<8,15>): User profile name(<=15 chars)[root]: User's Level: 1. Common User 2. Operator 3. Administrator:3 Permitted Reenter Number(0--4):4 User's Appended Info(<=30 chars):working Adding user succeeds Repeat this operation? (y/n)[n]:n Board confirmation on IPMD frame UA5000-IPMD-50-test(config)#Board confirm 0
Contoh Penggunaan bila setelah di confirm masih belum terdeteksi : UA5000-IPMD-50-test(config)#board add 0/10 ? --------------------------------------------Command of config Mode: --------------------------------------------H601ADL Parameter: Board name H601ADLB Parameter: Board name H601ADLF Parameter: Board name H601ADRB Parameter: Board name H601AIUB Parameter: Board name H601CSL Parameter: Board name H601CSLB Parameter: Board name H601CSLC Parameter: Board name H601CSLI Parameter: Board name H601EAUA Parameter: Board name H601SDL Parameter: Board name H601SDLB Parameter: Board name H601TSSB Parameter: Board name H601TSSC Parameter: Board name H601VDL Parameter: Board name
H602ADM H603ADR H603CSMC H603CSR H605CSR H612E1TF H612EFPF H612EFTF H612GAUA H612HLAF H612HLEF H612HLSF H612RATF H612SDLB H612SLPF H612SLTF H612SPLI H612TSTF H612WATF
Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter: Parameter:
Board Board Board Board Board Board Board Board Board Board Board Board Board Board Board Board Board Board Board
name name name name name name name name name name name name name name name name name name name
Note : Bila setelah “Board Confirm 0” masih belum terlihat coba lakukan dengan manual Cara Manual Pilih Type Board sesuai dengan Board yang terpasang pada slot yang akan di configure
Adding Internet Speedy service Vlan 3004 smart Port vlan 3004 0/2 0 traffic table index 7 ip car 1024 priority 0 priority-policy tag-In-Package traffic table index 8 ip car 384 priority 0 priority-policy tag-In-Package Note : Traffic fisesuaikan dengan Up-Link, Bila menggunakan FO “index 7 ip car 1024 “ dan “index 8 ip car 384” Bila menggunakan VSAT “index 7 ip car 384 “ dan “index 8 ip car 64” multi-service-port Vlan “Speedy (VLAN)” board (Frame) (Board) vpi (VPI Number) vci (VCI Number) user-encap pppoe rx-cttr 7 tx-cttr 8 Contoh command : After Create VLAN SMART and Port, Traffic Table, and Board Confirm UA5000-IPMD-50-test(config)#multi-service-port Vlan 3004 board 0 6 vpi 0 vci 35 userencap pppoe rx-cttr 7 tx-cttr 8 UA5000-IPMD-50-test(config)#multi-service-port Vlan 3004 board 0 6 vpi 0 vci 35 userencap pppoe rx-cttr 7 tx-cttr 8
Keterangan command : Command diapply pada setiap Slot yang terinstall Board CSRB Bila menggunakan FO “index 9 ip car 1024 “ dan “index 10 ip car 384” Bila menggunakan VSAT “index 9 ip car 384 “ dan “index 10 ip car 64” (Frame) => Frame MSAN yang sedang di konfigurasi (Board) => Board CSRB MSAN pada slot yang sedang di konfigurasi (VPI Number) dan (VCI Number) => sesuai ketentuan Telkom setempat Contoh : Divre2,5,6 menggunakan VPI 0 VCI 35, Divre-7(Makassar) menggunakan VPI 8 VCI 81 adsl line-profile quickadd 15 basic-para all trellis 1 bitswap 1 1 channel fast adapt atstartup snr 6 0 31 6 0 31 rate 32 1024 32 384 name Speedy_1MHome Keterangan command : 15 Merupakan Number Line Profile Speedy disesuaikan dengan permintaan Pihak Telkom name Speedy_1MHome Merupakan Line Profile Name sesuai permintaan Pihak Telkom Bila menggunakan FO menggunakan “rate 32 1024 32 384 Bila menggunakan VSAT menggunakan rate 32 384 32 64 interface adsl 0/6 deactivate all activate all profile-index 15 quit Keterangan command : Command diapply pada setiap Slot yang terinstall Board CSRB Adding Voice over BB (SIP Phone) service vlan “VoBB (VLAN)”standard port vlan “VoBB (VLAN)” 0/2 0 traffic table index 11 ip car 512 priority 7 priority-policy tag-In-Package traffic table index 12 ip car 512 priority 7 priority-policy tag-In-Package multi-service-port Vlan “VoBB (VLAN)” board (Frame) (Board) vpi (VPI Number) vci (VCI Number) user-encap pppoe rx-cttr 11 tx-cttr 12 Contoh command : UA5000-IPMD-50-test(config)#multi-service-port Vlan 4000 board 0 6 vpi 1 vci 36 userencap pppoe rx-cttr 11 tx-cttr 12 Keterangan command : Command diapply pada setiap Slot yang terinstall Board CSRB (Frame) => Frame MSAN yang sedang di konfigurasi (Board) => Board CSRB MSAN pada slot yang sedang di konfigurasi (VPI Number) dan (VCI Number) => sesuai ketentuan Telkom setempat
adsl line-profile quickadd 16 basic-para all trellis 1 bitswap 1 1 channel fast adapt atstartup snr 6 0 31 6 0 31 rate 32 1024 32 384 name Tripple_play Keterangan command : 16 Merupakan Number Line Profile VoBB disesuaikan dengan permintaan Pihak Telkom name Tripple_play Line Profile Name VoBB rate 32 1024 32 384 Merupakan Downstream and Upstream MSAN terhadap subscribers interface adsl 0/6 deactivate all activate all profile-index 16 quit Keterangan command : Command diapply pada setiap Slot yang terinstall Board CSRB # if want to test VoBB, suggest to use ADSL2+ Home gateway that support port mapping on each FE port on the modem.
Adding Vlan H.248 and Vlan Voice Media vlan 1001 standard port vlan 1001 0/2 0,6-7 vlan 2001 standard port vlan 2001 0/2 0,6-7
EMU (Fan) pada MSAN Indoor-AC, Outdoor D200 , serta D500 (Cukup hanya di lakukan pada IPMD saja, silahkan copy-paste command2 berikut sesuai )
MSAN OUTDOOR D200 emu add 0 power4875 0 0 rs232 GEPS4875_MsanD200 interface emu 0 power battery parameter 0.18 60 1 80 power battery temperature 60 -40 80 power charge voltage equalizing-voltage 56.5 floating-voltage 54.6 battery off permit 43.2 power environment temperature 50 0 55 -5 power environment humidity 80 10 95 0 power outside_digital 0 low-level MasterFrame_FAN power outside_digital 2 high-level Battery_on_load power outside_digital 3 low-level SPD_Failed power outside_digital 4 high-level Smoke_Alarm power outside_digital 5 high-level Heat_Exchanger quit
emu add 1 power4875 0 0 rs232 GEPS4875_MsanD200 interface emu 1 power battery parameter 0.15 60 1 80 power battery temperature 60 -40 80 power charge voltage equalizing-voltage 56.5 floating-voltage 54.6 power off permit 43.2 power environment temperature 50 0 55 -5 power environment humidity 80 10 95 0 power outside-digital 0 low-level MasterFrame_FAN power outside-digital 2 high-level Battery_on_load power outside-digital 3 low-level SPD_Failed power outside-digital 4 high-level Smoke_Alarm power outside-digital 5 high-level Heat_Exchanger
MSAN OUTDOOR D500 emu add 0 power4875 0 0 rs232 GEPS4875_MsanD500 interface emu 1 power battery parameter 0.15 60 1 150 power battery temperature 60 -40 80 power battery-test auto-discharge-permit 180 0 2 46 power charge voltage equalizing-voltage 56.5 floating-voltage 54.6 power off load-off-state permit load-off-voltage 44 battery-off-state permit battery-off-voltage 43.5 power environment temperature 50 0 55 -5 power environment humidity 80 10 95 0 power power power power power quit
outside-digital outside-digital outside-digital outside-digital outside-digital
0 2 3 4 5
available-level available-level available-level available-level available-level
low-level name MasterFrame_FAN high-level name Battery_on_load low-level name SPD_Failed high-level Smoke_Alarm high-level Heat_Exchanger
MSAN INDOOR AC Cabinet emu add 0 power4875 0 0 rs232 GEPS4875_MSANF02A interface emu 1 power battery parameter 0.15 60 1 100 power battery temperature 60 -40 80 power battery-test auto-discharge-permit 180 0 2 46 power charge voltage equalizing-voltage 56.5 floating-voltage 54.6 power off load-off-state permit load-off-voltage 44 battery-off-state permit battery-off-voltage 43.5 power environment temperature 50 0 55 -5 power environment humidity 80 10 95 0 power power power power
outside-digital outside-digital outside-digital outside-digital
0 2 3 4
available-level available-level available-level available-level
low-level name MasterFrame_FAN high-level name Battery_on_load low-level name SPD_Failed high-level Smoke_Alarm
power outside-digital 5 available-level high-level Heat_Exchanger quit
NOTE : # Be aware that if IPMD is on the UA5000 frame, IPMD will have more priority controlling the EMU then PVMD. (Tidak disarankan melakukan configurasi via PVMD, HARUS via IPMD)
PVMD (Narrowband Control Board) (Untuk Data PVMD MSAN, Perhatikan data pada NARROWBAND masing2 DIVRE, dari File Excel MSAN)
NMS connection to N2000 BMS sysname “MSAN00-(DIVRE)-(DATEL)-(MSAN-Vendor)” seperti pada IPMD
Sama
#Konfigurasi Ethernet Ke-1 IP untuk Management/NMS Interface eth ip modify 10.10.10.2 ip_address 172.29.180.12 submask 255.255.255.192 gateway 172.29.180.1 vlan_tag 23 quit Sebelum melakukan perubahan terlebih dahulu harus display status current interface : UA5000-PVMD-Test(config)#display ip address Eth: IPAddress............: 10.10.10.2 SubMask..............: 255.255.255.0 GateWay..............: 10.10.10.1 MacIndex.............: 0 MacAddress...........: 00-25-9E-22-EE-F2 VlanID...............: --
IP Eksisting
Contoh : Data ”NMS (IP & netmask)“ adalah 172.27.245.4/29 dengan “NMS (Gateway IP)“ adalah 172.27.245.1/29, dan “NMS (VLAN)” adalah Vlan 21, Maka Printah akan menjadi : UA5000-PVMD-Test(config)#Interface eth UA5000-PVMD-Test(config)#ip modify 10.10.10.2 ip_address 172.27.245.4 submask 255.255.255.248 gateway 172.27.245.1 vlan_tag 21 UA5000-PVMD-Test(config)#quit UA5000-PVMD-Test(config)#display ip address Eth: IPAddress............: 172.27.245.4 IP sudah
Berubah SubMask..............: 255.255.255.248 GateWay..............: 172.27.245.1
MacIndex.............: 0 MacAddress...........: 00-25-9E-22-EE-F2 VlanID...............: 21
snmp-agent community read public snmp-agent community write private snmp-agent target-host trap address 172.29.128.4 securityname huawei v2c snmp-agent target-host trap address 172.29.128.5 securityname huawei v2c snmp-agent trap enable standard autosave interval on Working mode integrated uplink tps on Create additional admin user on PVMD board Command:
terminal user name
User Name(length<6,15>):admin The user name must be equal to or more than 6 characters User Name(length<6,15>):admin The user name must be equal to or more than 6 characters User Name(length<6,15>):admin123 User Password(length<8,15>): r00tw3rk#@! Confirm Password(length<8,15>): User profile name(<=15 chars)[root]: User's Level: 1. Common User 2. Operator 3. Administrator:3 Permitted Reenter Number(0--4):4 User's Appended Info(<=30 chars):working Adding user succeeds Repeat this operation? (y/n)[n]:n
Board confirmation on PVMD frame (indoor) UA5000(config)#frame add 0 FrameType: 0 : MAIN_HABM_30(HABA) 2 : MAIN_HAFM_6(HABL) 4 : MAIN_H601HABC(HABC) 6 : SLAVE_HABS_32(HABB) 8 : SLAVE_HAFS_30(HABD) 10 : SLAVE_H602HABE(HABE) 12 : RSU_HABS_30(HABA) 14 : RSU_HAFS_6(HABL) 16 : RSUG_ONU04A 18 : RSP_19(HCB) 20 : RSP_14(HIB) 22 : RSP_10(HGB) 24 : RSP_6B(HLB) 26 : UAS_R (HUBS) 28 : UAFS_R(HUBF) 30 : ONU60A_R(HUBO)
# adding the HABA main master frame
11 13 15 17
: : : :
31 :
1 : MAIN_HAFM_30(HABD) 3 : MAIN_H602HABD(HABD) 5 : SLAVE_HAFS_32(HABE) 7 : SLAVE_HABS_30(HABA) 9 : SLAVE_H602HABD(HABD) RSU_HAFS_30(HABD) RSU_HAFS_12(HABC) RSUG_ONU60A(HUBO) RSUG_ONU08A 19 : RSP_15(HDB) 21 : RSP_12(HFB) 23 : RSP_6A(HMB) 25 : UAM_R (HUBM) 27 : UAFM_R(HUBE) 29 : UAMB_R(HUBB) ONUF01D100_R(HUBL)
32 : 34 : 36 : Please
VRSP_12(HABA) 33 : VRSP_18(HABA) HWTA(HIB_1) 35 : HWTA(HIB_2) HWTA(HIB_3) select frame type (0 ~ 36): 0 (PILIH SESUAI FRAME YANG TERINSTALL)
Note : Power-ON Pastikan Indikator FAN dalam status Normal (Green-Blinking) Pilih Frame sesuai dengan yang terinstal di site Board confirmation on PVMD frame UA5000-PVMD-Test(config)#Board confirm 0 Contoh Penggunaan : UA5000-PVMD-Test(config)#board add 0/10 ? --------------------------------------------Command of config Mode: --------------------------------------------A32 32-port analog subscriber line board ASL 16-port analog subscriber line board ATI Analog trunk interface board CDI 16-port direct dial-in subscriber interface board CSM 16-port analog subscriber line board CSR 32-port analog subscriber line board DSL Digital subscriber line board H301HWTA Remote subscriber processing board H601DSLD 16-port Digital subscriber line board H601DSLE 16-port Digital subscriber line board H601EDTB 16-port E1 conversion board H601PVMD Protocol processing and main node board H602PWX Secondary power board H602RSUG 2-port G.SHDSL and 1-port E1 Remote subscriber H611SDLE 8-port G.SHDSL and 8-port E1 conversion board H612EDTB 16-port E1 conversion board HSL High speed synchronization line board PWX2 Secondary power board PWX3 Secondary power board PWXA Secondary power board RSP Remote subscriber processing board RSU4 4-port E1 Remote subscriber processing board RSU8 8-port E1 Remote subscriber processing board SDL 4-port G.SHDSL and 4-port E1 conversion board TSS Subscriber test board VFB Voice frequency board
Note : Bila setelah memberikan “Board Confirm 0” masih belum terlihat, coba lakukan dengan manual Cara Manual Pilih Type Board sesuai dengan Board yang terpasang pada slot yang akan di configure
frame connect 0 1
# must connect the HW cable between HWCF to HWTF via HWOUT1 from HWCF and HWIN0 from HWTF. # for HABD to HABF only need to connect HWOUT0 from HWCF from HABD to HWIN0 from HWTF on HABF extended frame. No need to add frame and connect it. Automatically HABD frame will have from 0-17 and 18-35 slots.
H.248 Voice over IP connection to Softswitch #Konfigurasi Ethernet Ke-2 IP untuk IP H.248 Interface eth ip address 172.29.160.8 255.255.255.192 172.29.160.1 vlan_tag 1001 quit
#Konfigurasi Ethernet Ke-3 IP untuk IP VOICE MEDIA Interface eth ip address 172.29.140.8 255.255.255.192 172.29.140.1 vlan_tag 2001 quit Contoh Penggunaan : Contoh data : No.
Description (MSAN Outdoor)
Makassar_Mamasa
Narrowband 7 8
H248 (VLAN)
1001
H248 (IP & netmask)
172.29.160.69 /26
10
H248 Gateway IP
172.29.160.65 /26
11
Voice media (VLAN)
12
Voice media (IP & netmask)
172.29.140.69 /26
13
Voice Gateway IP
172.29.140.65 /26
UA5000-PVMD-Test(config)# Interface UA5000-PVMD-Test(config)#ip address 172.29.160.65 vlan_tag 1001 UA5000-PVMD-Test(config)#quit UA5000-PVMD-Test(config)# Interface UA5000-PVMD-Test(config)#ip address 172.29.140.65 vlan_tag 2001 UA5000-PVMD-Test(config)#quit
#Konfigurasi QoS pada Interface H.248 qos ip 172.29.160.8 strategy none qos ip 172.29.160.8 strategy tos qos ip 172.29.160.8 tos signalling 3 5
2001
eth 172.29.160.69 255.255.255.192
eth 172.29.140.69 255.255.255.192
# Konfigurasi QoS pada Interface VOICE MEDIA qos ip 172.29.140.8 strategy none qos ip 172.29.140.8 strategy tos qos ip 172.29.140.8 tos media 2 5 #Konfigurasi Interface H.248 interface h248 0 Are you sure to add MG interface?(y/n)[n]:y if-h248 attribute mgip 172.29.160.8 (H248 mgport 2944 mg-media-ip 172.29.140.8 transfer udp mgcip_1 172.29.132.4 mgcport_1 “2944 if-h248 attribute start-negotiate-version 1 deviceName MSAN_Huawei quit Contoh Penggunaan dengan contoh data : No.
Description (MSAN Outdoor)
Makassar_Mamasa
Narrowband H248 (IP & netmask)
172.27.245.12 /29
10
8
H248 Gateway IP
172.27.245.9 /29
12
Voice media (IP & netmask)
172.27.245.20 /29
13
Voice Gateway IP
172.27.245.17 /29
18
SS IP address (MGC_IP)
172.27.240.2 /29
19
SS UDP port MGC_port)
2944
UA5000-PVMD-Test(config)# interface h248 0 Are you sure to add MG interface?(y/n)[n]:y UA5000-PVMD-Test(config)# if-h248 attribute mgip 172.27.245.12 mgport 2944 mg-media-ip 172.27.245.20 transfer udp mgcip_1 172.27.240.2 mgcport_1 2944 UA5000-PVMD-Test(config)# if-h248 attribute start-negotiate-version 1 deviceName MSAN_Huawei UA5000-PVMD-Test(config-if-h248-0)#display if-h248 attribute --------------------------------------------------------------------MGID 0 MG Description MG DomainName Protocol H248 H248version Negotiated Originally 1 Profile Negotiation Para disable Profile 0:NoProfile("") 2833Encrypt Codetype Text Transmode UDP HeartBeatTimer(s) 60 HeartBeatRetransTimes 3 HeartBeatRetransTimer(s) 60 MG signalling IP 172.27.245.12 MG signalling Port 2944 MG media IP 172.27.245.20 MIDType IP4_ADDR DeviceName MSAN_Huawei Active MGC
MGC Port
:2944
MGC IP: 172.27.240.2
Active MGC MGC Domain Name:Standby MGC MGC Port :MGC IP:Standby MGC MGC Domain Name:---------------------------------------------------------------------
# Konfigurasi TID- Template dan TID-Format (HANYA DIGUNAKAN PADA MSAN YANG MENGINDUK KE SOFTWITCH ZTE) interface h248 0 tid-template add 32 format %u parameter-list “TID-template format for temporary RTP” name “SoftSwitch type” tid-format rtp template 32us quit Note : IMPORTANT !!! Harap di perhatikan bahwa kondisi default untuk TID-FORMAT pada MSANHUAWEI adalah : UA5000-PVMD-Test(config)#interface h248 0 UA5000-PVMD-Test(config-if-h248-0)# display tid-template 1 ------------------------------------------------Index : 1 Format : %u Para-list
: R+100000001
Name : Rtp_No_Delamination -------------------------------------------------
Maka untuk mengubah Parameter TID-FORMAT menjadi “R+65535” pada MSANHUAWEI adalah : UA5000-PVMD-Test(config-if-h248-0)# tid-template add 32 format %u parameterlist R+65535 name SS_ZTE UA5000-PVMD-Test(config-if-h248-0)# display tid-template 32 ------------------------------------------------Index : 32 Format : %u Para-list
:
R+65535 Name : SS_ZTE ------------------------------------------------UA5000-PVMD-Test(config-if-h248-0)# display tid-format -------------------------------user-type template-index prefix -------------------------------rtp 32 A pstn 2 A bra 2 A pra 2 A r2 2 A dpnss 2 A dass2 2 A --------------------------------
# Konfigurasi Prefix TID- Template dan TID-Format (HANYA DIGUNAKAN PADA MSAN YANG MENGINDUK KE SOFTWITCH NSN) Note : IMPORTANT !!! Harap di perhatikan bahwa kondisi default untuk TID-FORMAT pada MSANHUAWEI adalah : UA5000-PVMD-Test(config)#interface h248 0 UA5000-PVMD-Test(config-if-h248-0)# display tid-format all ------------------------------------------------MGID user-type template-index prefix ------------------------------------------------0 RTP 1 A 0 PSTN 2 A 0 BRA 2 A 0 PRA 2 A 0 R2 2 A 0 DPNSS 2 A 0 DASS2 2 A ------------------------------------------------UA5000-PVMD-Test(config-if-h248-0)# tid-format rtp prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format pstn prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format bra prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format pra prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format r2 prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format dpnss prefix port_ UA5000-PVMD-Test(config-if-h248-0)# tid-format dass2 prefix port_ UA5000-PVMD-Test(config-if-h248-0)# display tid-format all ------------------------------------------------MGID user-type template-index prefix ------------------------------------------------0 RTP 1 port_ 0 PSTN 2 port_ 0 BRA 2 port_ 0 PRA 2 port_ 0 R2 2 port_ 0 DPNSS 2 port_ 0 DASS2 2 port_ -------------------------------------------------
NOTE : # Konfigurasi Prefix TID- Template dan TID-Format PADA MSAN YANG MENGINDUK KE SOFTWITCH HUAWEI TIDAK MENGALAMI PERUBAHAN SAMA SEKALI
# LAKUKAN RESET setelah selesai konfigurasi H.248 UA5000-PVMD-Test(config)#interface h248 0 UA5000-PVMD-Test(config-if-h248-0)# reset coldstart yes UA5000-PVMD-Test(config-if-h248-0)# display if-h248 all #should be normal if already connected to SoftSwitch.
#PILIH
# Konfigurasi User H.248 KONFIGURASI INI HANYA BISA DIGUNAKAN BILA SUDAH DI PEROLEH RANGE NO.TELEPON DARI PIHAK TELKOM YANG AKAN DI INPUT PADA MSAN Esl user mgpstnuser batadd FrameA/BoardA/PortA FrameB/BoardB/PortB 0 terminalid 0 telno 42560000 step 1 quit Contoh Penggunaan : FrameA/BoardA/PortA dan FrameB/BoardB/PortB merupakan Board ASL, A32, dan CSRB FrameA/BoardA/PortA merupakan Board AWAL (Board ASL, A32, dan CSRB) FrameB/BoardB/PortB merupakan Board AKHIR (Board ASL, A32, dan CSRB) 0 merupakan MGID terminalid 0 merupakan START TID step 1 merupakan jumlah penambahan nomer and TID sesuai jumlah step Misal Pada sebuah Frame terdapat 4CSRB, 2A32, 3ASL. Maka Jumlah Subscriber Narroband yang tersedia adalah : 128 + 64 + 48 = 240 4 CSRB 2 A32 3 ASL Telkom
= 4 * 32 = 128 = 2 * 32 = 64 = 3 * 16 = 48 memberikan Nomer 7567000 7567239 :
Maka Commandnya Menjadi : UA5000-PVMD-Test(config)# ESL user UA5000-PVMD-Test(config-esl-user)# mgpstnuser batadd 0/6/0 0/14/15 0 terminalid 0 telno 7567000 step 1 UA5000-PVMD-Test(config-esl-user)# quit UA5000-PVMD-Test(config-esl-user)# display mgpstn user 0/6
Configuring Inner Digitmap for emergency calling within the same MGID interface h248 0 mg-software parameter 11 3 display mg-software parameter 11
Contoh Penggunaan Command : UA5000-PVMD-Test(config if-h248-0)# interface h248 0 UA5000-PVMD-Test(config if-h248-0)# mg-software parameter 11 3 UA5000-PVMD-Test(config if-h248-0)# display mg-software parameter 11 ------------------------------------------------Interface Id:1 para index:11 value:3 ------------------------------------------------APPENDIX: ------------------------------------------------Interface soft parameter name: 11: Stand alone support 0 : None 1 : Inner 2 : Emergency 3 : Both
standalone parameters dialtone 15 ring 60 busytone 50 display standalone parameters Contoh Penggunaan Command : UA5000-PVMD-Test(config if-h248-0)# standalone parameters dialtone 15 ring 60 busytone 50 UA5000-PVMD-Test(config if-h248-0)# display standalone parameters -----------------------------------------------------------------System stand alone para of timer for dial tone :15 (s) System stand alone para of timer for busy tone :50 (s) System stand alone para of timer for ring :60 (s) ------------------------------------------------------------------
digitmap set inner ”xxxxxxxx” display digitmap Note : IMPORTANT !!! Jumlah inner digitmap diKoordinasikan dengan Technical Leader Huawei Contoh Penggunaan Command : UA5000-PVMD-Test(config if-h248-0)# digitmap set inner ”xxxxxxxx” UA5000-PVMD-Test(config if-h248-0)# display digitmap -----------------------------------------------------------------Inner digitmap : xxxxxxxx Emergency digitmap : Urgent digitmap (for overload or bandwidth restrict) : Dualdial digitmap for card service : -----------------------------------------------------------------UA5000-PVMD-Test(config if-h248-0)# quit UA5000-PVMD-Test(config)#
Diposkan oleh masyusdi panjul di 06.13 Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke Facebook Reaksi:
COMMISIONING NOKIA FLEXY HOPPER Dan postingan saya berikutnya adalah mengenai langkah-langkah commisioning FLEXY HOPPER MANAGER perangkat NSN mari kita terus belajar dan belajar supaya menjadi pintar,dan yang jelas semakin banyak ilmu kita maka semakin banyak keuntungan yang kita peroleh disamping materi ok gaaaaaann.... bagi yang dah mahir boleh dong berbagi di sini!! untuk menyempurnakan blog saya ini. thanks.
Diposkan oleh masyusdi panjul di 05.58 Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke Facebook Reaksi:
BACKBONE ....PLEASE FILL COMENT FOR THIS PICTURE DID YOU KNOW? TAHUKAH ANDA? Silahkan anda semua berkomentar tentang gambar yang saya posting ini ,tapi komentar yang enak2 aja di dengar dan di baca..
MODERN INSTALLATION
INDONESIAN "SAMSON"
VS
Diposkan oleh masyusdi panjul di 05.06 Kirimkan Ini lewat EmailBlogThis!Berbagi ke TwitterBerbagi ke Facebook Reaksi:
Senin, 01 Juli 2013 MINI LINK AS ETHERNET BRIDGE
iklan jika anda punya blog/website pasang iklan AdRewa klik disini http://adrewa.com/index.php?r=83
