Siae AL+2 Manual Configuration Instructions (Draft)

KORDIA SOLUTIONS

SIAE AL+2 – MANUAL CONFIGURATION INSTRUCTIONS

ABSTRACT: This document details the connections and configuration required to ensure NMS connectivity to Siae microwave links

Commercial In Confidence

1

DOCUMENT KOS-V3G-DOC-024

Document Status Record DOCUMENT REVISION RECORD ISSUE NO

ISSUE DATE

PREPARED BY

0

04/11/2009

Yu Xu

REVIEWED BY

PAGES IN DOCUMENT

CHANGE HISTORY ISSUE NO 0

DESCRIPTION Draft issued.

CONTACTS AND AUTHORISATION NAME

TITLE

Yu Xu

Transmission Engineer

NUMBER

SIGN OFF

0424 149 086

DOCUMENT DISTRIBUTION NAME

TITLE

DATE

REFERENCE DOCUMENTS

TITLE

DATE

2


Table of Contents 1 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7

Introduction....................................................................................4 Configuration Instructions .............................................................. 5 Connect to a Siae IDU......................................................................5 IDU and ODU Configuration..............................................................6 DCN Port Configuration....................................................................8 Routing Table Configuration............................................................10 Stored Routing Table Configuration..................................................12 OSPF Configuration........................................................................13 Example Siae DCN network.............................................................15

3


1 Introduction This manual has brief instructions to setup Siae microwave radios in Vodafone network. There are there steps involved. The first step is to configure the modulation, capacity, frequency, agent IP and remote element table to bring up the link. The second step is to configure the ports and interfaces, Ethernet port and radio interface are the most important. The final step is to configure the routing table and OSPF. Once this has been done correctly, this link can be connected and managed by Siae NMS5UX.

4


2 Configuration Instructions 2.1 Connect to a Siae IDU What do you need?  SCT software installed.  1 x USB cable with type A plug and type B plug. Run SCT software. Setup the connection: Options  Connection  Connect using direct serial cable Please refer to the How_to.pdf for details.

How_to.pdf

Click Connect and enter the user name and password, and then click OK. User: SYSTEM Password: siaemicr

5


2.2 IDU and ODU Configuration To configure the IDU and ODU properties such as agent IP, remote element table, frequency, modulation and capacity, etc., highlight the IDU, Equipment  LCT Interface.

1. Equipment Properties (Equipment ID and Agent IP) o Set the Equipment ID as per Tx Design. o Set Agent IP same as the Ethernet IP adddress. o Click Apply to save the changes.

2. Remote Element Table 6


o o o o

Add a new Station if there is no existing Station. Add local element. Set IP as local equipment IP and check Managed by SCT. Click OK to save. Add remote element. Set IP as remote equipment IP and check Remote Link. Click OK to save. Click Apply to save the changes.

3. Local Link ID, Modulation and Capacity o Click Equipment menu  Mod. Cap/Link ID to access. o Set Local Link ID to 0 to disable this function or set the value as per LER. Both ends must have the same local link ID. o Set Bandwidth and Modulation as per LER. o Click Apply to save the changes.

7


4. Power o o o o o o o o

and Frequency Click Equipment menu  Radio Branch 1A to access. Set the Tx Power as per LER. Set Tx Power Control to Manual to disable ATPC or Automatic to enable ATPC. Set Bandwidth and Modulation as per LER. Set Carrier Only to OFF (Set it to ON will lose the traffic). Set Tx Transmitter to ON. Set RT PSU to ON (Power to the ODU). Click Apply to save the changes.

2.3 DCN Port Configuration To configure the DCN interfaces, highlight the IDU, Equipment  Communication Setup  Port Configuration. 1. IP Ethernet (The IP address for the Ethernet port of the IDU) o Set the IP address and Net Mask as per NMS design. o Make sure the LAN 1 Cable Crossover is auto. o Click Set Values and Store.

8


2. PPP RS-232 o Add later 3. LCT PPP (The USB LCT PPP connection configuration) o Change the IP PPP Address to 192.168.0.1 and Net Mask to 255.255.255.240 o Set PC IP Address to Port IP Address + 1 o Click Set Values and Store.

4. Radio 1A (The Radio IP configuration) o Set IP address and Net Mask to IP Unnumbered. o Always set PPP mode to Client. 9


o

Click Set Values and Store.

5. 2mb EOC o Add later 6. Click Restart to take the changes into effect.

2.4 Routing Table Configuration Only Default Gateway in the Routing Table is required, once the OSPF is switched on, it will generate a proper routing table. To access the Routing Table, highlight the IDU, Equipment  Communication Setup  Routing Table. 1. Set the Default Gateway as per NMS design. o In the trial link setup, the Near End Default Gateway is the router address. The Far End Default Gateway is the Near End Radio (same address as the Near End Ethernet IP). 2. Click Apply to save the configuration.

10


Near End Routing Table

Far End Routing Table

11


2.5 Stored Routing Table Configuration Only Default Gateway in the Stored Routing Table is required. To configure the Stored Routing Table, highlight the IDU, Equipment  Communication Setup  Stored Routing Table. 1. Set the Default Gateway as per NMS design. o In the trial link setup, the Near End Default Gateway is the router address. The Far End Default Gateway is the Near End Radio (same address as the Ethernet IP). 2. Click Apply and then click Save to save the configuration.

Near End Stored Routing Table

Far End Stored Routing Table 12


2.6 OSPF Configuration OSPF is required to bring the NMS online. To configure the OSPF, highlight the IDU, Equipment  Communication Setup  OSPF.

1. Properties o Check OSPF Process Active to enable the OSPF o Click Apply to save the changes.

2. Areas/Ifs

13


o

Add a   

new OSPF Area. Click Add to add new area. Set the Area ID and Stub Area as per NMS Design. Click Add to save the new area.

o

Add Interfaces to the new area.  Drag the Radio1A and Lan interfaces from Area 0.0.0.0 to the new Area.  Set Radio 1A Status to Active.  Set Lan Status to Active.  Click Apply to save the changes.

3. Click Store to save the changes to memory. 14


Example Siae DCN network

15


Siae AL+2 Manual Configuration Instructions (Draft)

Recommend Documents