SCVT Pocket Guide.docx

1: Device Power ON

3: Selecting XCAL App

Press here to Power On

SCVT Pocket Guide

4: Checking GPS Status

2: Enabling GPS

Gototo“Apps”& “Apps”& Select Select “XCAL ”App Go “XCAL ”App Slide Down & Select GPS “On”

5: 4 Selecting Report Mode

6: Setting Band Selection

7: Setting Band Selection

1 When executing the application, a notification screen pops up for checking up the status of DM and GPS. Once both DM and GPS status are completely verified, the application becomes in

If you changing Band You Will See this Prompt Just

Press “Optio n”

Click On This

After Pressi ng “OK” Restar

2 Select1800 / 2300 Band &

Click On “Check” Button to

8: 6: Setting Band Selecting GPS Value Information

9: Selecting Cluster Information

10: Cluster Information Downloaded Select Target Cluste r

Press “Down ” Click On “GPS Value”. Long press on Map Screen to get Lat/Long & Press “Ok” & then press

Cluster, scenarios & Site list informatio n getting downloade d

Press back

12: Identify the correct location for test

13: Stationary Settings

14: Selecting Scenario Press “Settin g”

Select Target Site Select Station1 for Alpha

Select the drive “Cycle” VoLTE “Termination

Stationary Test (12-19)

Perform Stationary Test (ST) as per given process in each sector i.e. in Alpha, Beta & Gamma. 15: Autocall Start

Check PCI of sector before Starting the test Please make sure all circle are green before Starting the test wherever is possible. This might not be achieved in

“SCVT”

Perform the stationary test in front of the Antenna of the testing sector with a distance of 50-100 Meters from the tower in the direction of Antenna facing as shown above.

11: SCFT Stationary Test

“Setting” details can be verified after step 13

Select Scenario as “SCVT” and FTP as local FTP defined

Press “Start ”

16: AutoCall Views

17: AutoCall Views

18: AutoCall Views

19: Drive progress flag selection Once Stationary test completed, select the test completion flag as per below: Select “In Progress” for Station1

1 Click On “Option ”& Then Map to see map or “LTE Summa ry

18: Log Upload

Press “CANCE L”

2

20: SCVT- Stationary 2 for Beta sector  Repeat Steps 12-18 for Stationary 2 Beta.  Please do following modification in “setting” in step 13 &“flag” in step 17 as shown below.

21: SCVT- Stationary 3 for Gama sector  Repeat Steps 12-18 for Stationary 3 Gama.  Please do following modification in “setting” in step 13 & “flag” in step 17 as shown below. Select Station 3 for Gama sector

Select Station 2 for Beta sector

Select “In Progress ” for Station2 (Beta

Select “Complet e” for Station3 (Gama

25: Autocall Start

24: Selecting Scenario

“Setting” details can be verified after step 22

29: Map View

To See the Map. Press “Option” & then on Map

23: Moving Settings

Moving Test

Press “Settin g”

(22-28)

“SCVT” Start Moving Test with Handover test by moving clockwise & anticlockwise (preferably walk test) to capture the intra-site HO between all sectors of the site in both directions and then do the remaining drive test covering best server area of all sectors of

Select Target “Moving

“Save”

26: AutoCall Views_DTDL

Select the same drive “Cycle” as Stationary Test

27: AutoCall Views_DTUL

Select in one handse t DTDL & In other DTUL Press “Start ” Simult

Scenario “DTDL” in one handset and Scenario “DTUL” in second handset.

28: AutoCall Views

22: SCVT Moving Test

Serving PCI

You can see Successf ul HO by this Sign

30: DT Completion Flag Select the test completion flag: Press “Complete” or “In Progress”, simultaneously in both DTDL & DTUL Handset, depending on completion of drive.

31: Log Upload for all logs at one go Go to upload “Upload”

1 Press “Select all”

2 Uncheck the “ticks” on folders at top and then press “Upload” Wait Upload to finish. If failed, please cancel and upload again

32: Things to check before SCFT

• Site Database from SOLPAR manager. • 2 LTE Handsets (S4 Mini) fully charged. • Sufficient storage space to store the logfiles. • Magnetic Compass, Tilt Meter & Laser meter • Drive route printout, based on best server plot, prepared by SOLPAR engineer. • Pre checks with LSM-R engineer. • Obtaining door key & site access via respective authority. • Authorization letter from RJIL, to conduct drive test. • Delete the garbage log file or already uploaded log files in to FMS from the both handsets. Always keep backup of log files in

35: Things to remember during SCFT (Very Important) • Check GPS is stable as per step-4. • Never conduct stationary test, in between two sectors i.e. in overlapping zone. Always do in main lobe or in front of the antenna of testing sector as per step-12. • Ensure correct PCI update, during handover when moving clockwise/ Anti clockwise from (alpha PCI to Beta PCI, Beta PCI to Gama PCI, Gama PCI to Alpha PCI & Vice versa) to capture the Handover attempt. If handover doesn’t happen as per requirement, contact circle RF lead immediately. • Please drive through routes given, as

End