BILL OF MATERIALS ITEM QTY 50.18 5.92
36.00 18.00 N1
DESCRIPTION
MATERIAL
1
1
Pipe - Sch. Std, 12.00 NPS
2
2
Head, Pipe Cap - Sch. Std, 12.00 NPS
SA-234 WPB
SA-106B
3 4 5 6
1 1 2 1
Pipe - Sch. 40, 4.00 NPS Flange, RFSO - 150#, 4.00 NPS Half Coupling, SW - 3000#, 2.00 NPS Half Coupling, SW - 3000#, 0.50 NPS
SA-106B SA-105 SA-105 SA-105
7 8 9 10
2 4 1 1
Plate 0.375" thick Plate 7.50" x 2.00" x .375" Code nameplate bracket Code nameplate
SA-G40.21 38W SA-G40.21 38W SA-G40.21 38W Stainless
NOTES:
8.00 .38
0.125
0.500
1. 2. 3.
All dimensions in inches. All welds shall be neat in appearance, free from slag and other defects. Vessel to be cleaned of scale, oil,weld spatter and all other foreign material, prior to hydrostatic test. 4. Remove all sharp edges on nozzles (1/8" minimum radius) 5. All nozzles to support nomial loads only. 6. Grind welds flush under repads. 7. Maximum misalignment of butt joints is limited to .25T (Category A, B, C, D up to 1/2" thick) 8. All fittings conform to B16.9 standards. 9. All couplings to conform to B16.11 (2011 Add.) standards. 10. All flanges to conform to B16.5 (2009 Add.)/ B16.47 standards. 11. Flange bolt holes to straddle natural centre lines.
1.00
4 plc
14.38
12.75 N3
N2
12.03 8.81
2 0.250
8
Typ.
0.250 1
7
9
N4
10
0.625 Hole Typ.
2.00
7.00
Design Code: Seismic Code: Wind Code: Design Conditions MAWP - Int / Ext: MDMT: Corrosion Allowance: Examination Impact Testing: Radiography: PWHT: Hydro Test: Service Fluid: Capacity: Weight - Empty: Weight - Operating:
11.00
28.00 2.25
31.50
1.25
34.00
WELDS
Mark Size Qty. Service
Type
41
UW-16.1 (c) with 0.250 inside projection
FLANGES 42
43
Type
-
0.250
Slip on
SB
F1
F2
4"
1
Vent
N2
2"
1
Inlet
UW-16.1(c)
0.313
-
-
-
-
-
-
5
N3
2"
1
Outlet
UW-16.1(c)
0.313
-
-
-
-
-
-
5
0.50"
1
Drain
UW-16.1(c)
0.188
-
-
-
0.375 .237 0.370
BOM ITEM #
N1
-
-
-
SB
F2 F1
Slip On Flange
Outside
A
6
Typ. Circ. Seam
41
41 Outside Shell UW-16.1 (c)
REVISION HISTORY
DATE
DRW
CHK
0
Release
3/21/2012
KM
LB
XYZ Vessel Corp. 123 Basic Street Seatown, Ontario, Canada X1Y 2Z3
xyz
Nozzle
Typ.
REV.
3,4
43 Nozzle
N4
ASME VIII-1 2007 Ed. 2008 Add. N/A N/A 200 / 0 psi @ 300 °F -20 °F @ 200 psi 0 None per UG-20(f) 1-5 None None 260 psi @ Ambient Air / Water / Steam 6 cu. ft. 250 lbs 450 lbs
REVISIONS
NOZZLE SCHEDULE NOZZLE
DESIGN DATA
Code
Outside Shell UW-16.1 (c) with inside projection
Full Pen.
Certified by
S
M
w
E
XYZ Vessel Corp. (Name of Manufacturer) psi at °F 300 200 Max. allowable working pressure (MAWP) 300 °F 0 psi at Max. allowable external working pressure at 200 psi -20 °F Min. Design Metal Temperature (MDMT) -
To Follow CRN
Manufacturer's serial number 2012 Year built
Eng
Pressure Vessel Engineering, Ltd. 120 Randall Drive, Suite B Waterloo, Ontario, Canada N2V 1C6
www.pveng.com
[email protected] Tel. 519-880-9808 Fax 519-880-9810
Title
Design Calcs Sample
Size
Scale
Job ID
B
Drawing No.
PVE-5918
1:8
Material
See BOM
Design Calcs Sample Sheet
Revision:
0
1 OF 1
This drawing and the information herein is confidential, and must not be reproduced or used in any way without the written permission of Pressure Vessel Engineering Ltd.
