ABBREVIATIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
AGA AGS AMCA ANSI API APHA ARI ASHRAE ASME ASPE ASSE ASTM AWWA BS CAGI CEMA CEN CGA INC. CGA CGSB CMAA CSA CTI DEMA DIN EJMA EPA FEM GPSA ICC IEC IEEE IP IRC IS ISA
American Gas Association American Gas Society Air Moving and Conditioning Association American National Standards Institute American Petroleum Institute American Public Health Association Air-Conditioning and Refrigeration Institute American Society of Heating & Refrigeration Engineers American Society of Mechanical Engineers American Society of Plumbing Engineers American Society of Sanitary Engineers- Canadian Plumbing Code American Society For Testing of Materials American Water Works Association British Standard Compressed Air and Gas Institute Conveyor Equipment Manufacturers Association The European Committee for Standardization Compressed Gas Association Canadian Gas Association Canadian General Standards Board Crane Equipment Manufacturers Association of America Canadian Standards Association Cooling Tower Institute Diesel Engine Manufacturers Association Hydraulics Institute Deutsches Institute fur Normung (German Insitute for Standardization) Expansion Joint Manufacturers Association Environment Protection Agency Fédération Européenne de la Manutention (Rules for the Design of Hoisting Appliances) Gas Processor Suppliers Association International Code Council International Electro technical Commission Institute of Electrical & Electronics Engineers Institute of Petroleum Indian Road Congress Indian Standard Instrument Society of America
ABBREVIATIONS
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
ISO JIS JSA MHI MPTA MSS NACE NBBI NBFU NBS NCSBCS NEMA NFPA NIST OSHA PDI PFI PPI RMA SAMA SIS SMACNA TEMA TIMA WSSN
International Organization for Standardization Japanese Industrial Standards The Japanese Standards Association Material Handling Institute Mechanical Power Transmission Association Manufacturers Standardization Society of the Valve and Fittings Industry National Association of Corrosion Engineers National Bureau of Boiler & Pressure Vessel Inspectors National Board of Fire Underwriters National Bureau of Standards National Conference of States on Building Codes and Standards. National Electrical Manufacturers Association National Fire Protection Association National Institute of Standards and Technology Occupational Safety and Health Administration Plumbing and Drainage Institute-Provincial Plumbing Code Pipe Fabricators Institute Plastic Pipe Institute Rubber Manufacturers Association Scientific Apparatus Makers Association Swedish Standard Institution Sheet Metal & Air Conditioning Contractors National Association Tubular Exchanger Manufacturers Association Thermal Insulation Manufacturers Association World Standards Services Network
MECHANICAL Sl. No. CODES / STANDARDS
DESCRIPTION
1 2 3
API 5L API 6D API 6FA
Specification for line pipe Pipe line valves, end closers, connectors and swivels Recommended practice for fire test for valves
4
API 12C
5
API RP 12H
6 7 8
API RP 510 API 520 API 521
9
API RP 525
10 11
API 526 API 527
12
API RP 530
13 14
API PUBL 535 API 560
15
API 570
16 17 18
API 572 API 573 API RP 574
19
API RP 575
20 21 22 23 24 25 26 27
API 576 API RP 582 API 590 API 594 API 598 API 599 API 600 API 601
Oil storage welded tanks Recommended practice for installation of new bottoms in old storage tanks Inspection, repair and rating of unfired pressure Vessel Part I& II: Design and installation of pressure relieving systems, Guide for pressure relief and depressurizing systems Testing Procedure for pressure relieving devices discharge against variable back pressure Flanged Steel SRV Seat tightness of SRV Recommended practice for calculation of heater tube thickness in petroleum industries Burners for Fired Heaters in General Refinery Services Fired Heaters Piping Inspection code: Inspection, Repair, Alteration, and Re-rating of In-service Piping Systems Inspection of Pressure Vessels Inspection of fired boilers and heaters Inspection of piping , tubing, valves and fittings Guidelines and methods for inspection of existing atmospheric and low pressure storage tanks Inspection of pressure relieving devices Welding Guidelines for the Chemical, Oil and Gas Industries Steel line blanks Wafer type check valves Valves inspection and test Steel plug valves, flanged or butt welded ends Steel gate valves Metallic gaskets for piping- double jacketed, corrugated and spiral
28
API 602
Compact design carbon steel gate valves for use.
MECHANICAL Sl. No. CODES / STANDARDS
DESCRIPTION Corrosion Resistant, Bolted Bonnet Gate Valves Flanged and ButtWelding ends Fire test for soft seated ball valves Metal Ball Valves- Flanged, Threaded, and Welding end Butterfly valves (double flanged, lug, wafer type) Centrifugal pumps for general refinery services General purpose steam turbines for refinery services Special purpose steam turbines for refinery services Special purpose gear units for refinery services Gas Turbines for the Petroleum Chemical and Gas Industry Services Centrifugal compressors for general refinery services Reciprocating compressors for general refinery services Rotary type positive displacement compressors for general refinery services
29
API STD 603
30 31 32 33 34 35 36 37 38 39
API 607 API STD 608 API 609 API 610 API 611 API 612 API 613 API STD 616 API 617 API 618
40
API 619
41
API 620
Design and construction of large welded low pressure storage tanks
42 43 44 45 46 47 48 49 50
API RP 621 API 630 API 650 API 651 API 652 API 653 API 660 API 661 API 671
51
API STD 672
52 53 54 55 56 57
API 674 API 675 API 676 API STD 682 API TECH report 938-C API 941
Reconditioning of Metallic Gate, Globe, and Check Valves Tube and Header Dimension for fired heaters Oil storage tank Cathodic protection of above grade petroleum storage tanks Lining of above ground petroleum Storage tank bottoms Oil storage tank inspection, repair, alteration and re-construction. Shell and Tube Exchangers Air cooled heat exchanger for refinery services Special purpose couplings for refinery services Packaged, Integrally Geared, Centrifugal Air Compressors for Petroleum, Chemical and Gas Industry Services Positive displacement pumps-Reciprocating Positive displacement pumps-Controlled volume Positive displacement pumps-Rotary Pumps Shaft Sealing Systems for Centrifugal and Rotary Pumps Use of Duplex stainless steels in the oil refining industry Steel for hydrogen service at high temperatures and pressures
58
API RP 945
Avoiding Environmental Cracking in Amine Units
MECHANICAL Sl. No.
CODES / STANDARDS
59
API RP 1102
60 61 62 63 64
API 1104 API RP 1107 API RP 1110 API STD 1160 API 2000
65
API RP 2009
66
API 2015
67
API RP 2200
68
API 2201
69
API RP 2214-
70
API 2550
71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
API Tech report 2567 API CHAPTER-IV API CHAPTER-VI API CHAPTER- VII API CHAPTER-VIII API CHAPTER-IX API CHAPTER- XI API CHAPTER-XIII API CHAPTER-XVI ANSI/ASME B 1.1 ANSI/ASME B 1.20.1 ANSI/ASME B 1.20.3 ANSI/ASME B 1.20.7 ANSI/ASME B 16.1 ANSI/ASME B 16.3 ANSI/ASME B 16.4
DESCRIPTION Recommended practice for liquid petroleum pipe lines crossing railroads & highways Welding of pipe lines and related facilities Pipe lines maintenance welding practice Pressure Testing of Liquid Petroleum Pipelines Managing System Integrity for Hazardous Liquid Pipelines Venting atmospheric and low pressure storage Safe welding and cutting practices in refineries, gas plants & petrochemical plants Cleaning Petroleum Tanks Repairing Crude ole ,liquefied petroleum gas, and product Pipeline Procedure for welding or hot tapping on equipment containing flammables Spark ignition properties of hand tools Method for measurement and calibration of for upright cylindrical tanks Evaporative loss from storage tank, Floating roof Recommended practices for low pressure storage tanks Pressure Vessels (Towers, drums, reactors) Heat Exchangers, coolers, condensers Direct Fired Boiler and auxiliary Equipment Fired heaters and Stacks Pipes, Valves and Fittings Inspection of Atmospheric and low pressure storage tanks Pressure relieving Devices Unified inch screw threads (UN and UNR thread form) Pipe threads (except dry seal) Dry seal pipe threads, inch Hose coupling screw threads Cast iron flanged end fittings Malleable iron threaded fittings, Class 150 & 300 Cast iron threaded fittings, Class 125 & 250
MECHANICAL Sl. No. 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102
CODES / STANDARDS
104 105 106 107 108 109
ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME 18.2.2. ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME ANSI/ASME
110
ANSI/ASME B 31.4
111 112
ANSI/ASME B 31.8 ANSI/ASME B 31.11
113
ANSI/ASME B 31G
114 115 116
ANSI/ASME B 36.10M ANSI/ASME B 36.19M ANSI/ASME B 46.1
103
DESCRIPTION
B 16.5 B 16.9 B 16.10 B 16.11 B 16.14 B 16.15 B 16.20 B 16.21 B 16.25 B 16.28 B 16.34 B 16.36 B 16.39 B 16.42 B 16.47 B 16.48 B 18.2.1 &
Steel pipe flanges and flanged fittings Steel but welding fittings Face to face and end to end dimensions of valves Forged steel socket welding and threaded fittings Ferrous pipe plugs, bushings and lock nuts with pipe threads Cast bronze threaded fittings Ring joint gaskets and grooves for pipe flanges Non metallic gaskets for pipe flanges Butt welding ends Short radius elbows and returns Steel valves, flanged and butt welding ends Orifice flanges Malleable iron threaded pipe unions. Ductile iron threaded and flanged fittings, Class 150 & 300. Large Diameter Steel Flanges Steel line blanks
B 18.5 B 18.15 B 18.22.1 B 31.1 B 31.2 B 31.3
Round head bolts Forged eye bolts Plain washer Power piping Fuel Gas piping Chemical plant and petroleum refinery piping Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas Gas transmission and distribution piping systems Slurry Transportation Piping Manual for determining the remaining strength of corroded pipe lines. Welded and seamless Wrought steel pipes Welded and seamless Austenitic stainless steel pipes Surface textures
Square and hexagonal head bolts and nuts
MECHANICAL Sl. No.
CODES / STANDARDS
117
ASM Volume 1
118
ASM Volume 2
119 120 121 122 123
ASM Volume 11 ASM Volume 13A ASM Volume 13B ASM Volume 19 ASM Volume 20
124
ASM EPRI
125
ASME, Section I
127 128 129 130 131 132
ASME, Section IV ASME, Section V ASME BPVC SEC 2A ASME BPVC SEC 2B ASME BPVC SEC 2D ASME BPV
DESCRIPTION Properties and selection : Irons, Steels, and High- Performance Alloys Properties and Selection : Nonferrous Alloy and Special-purpose Materials Failure Analysis and prevention Corrosion : Fundamentals, Testing, and Protection Corrosion : Materials Fatigue and Fracture Materials selection and design Damage Mechanisms and life Assessment of High Temperature Components Power Boilers. Part-A: Material specification: Ferrous Part-B: Material specification: Non Ferrous
Heating boilers Non destructive testing Ferrous material specifications Non-Ferrous material specifications Properties (Customary) Ring Binders Process Piping: The Complete Guide to ASME B 31.3, Second Edition Fuel Transients in Pipeline Systems - 2nd Edition Pipeline Design and Construction (Second Edition) Flow-Induced Vibration of Power and Process Plant Components : A Practical Workbook, single edition Guidebook for the Design of ASME Section VIII Pressure vessels, Second Edition Reliability and Risk Management Boiler and Pressure Vessels Code Div.1: Rules for construction of pressure vessels Div.2: Alternative rules for construction of pressure vessels Div.3: Alternative rules for construction of High Pressure Vessels.
MECHANICAL Sl. No.
CODES / STANDARDS
135 ASME, Section IX 136 ASME, Section X
141 142 143 144 145 146
DESCRIPTION Welding and Brazing Qualifications Fiber -reinforced plastic Pressure Vessels.
Volume 01.01 : Steel- Piping, Tubing, fittings Volume 01.02 : FerFerrous materials: Iron and Steel Productsrous casting, Ferroalloys Volume 01.03 : Plates, Sheets, Strips, Wire Volume 01.04 : Structural, Reinforcing, Pressure Vessels, Railways Volume 01.05 : Bars, Forgings, Bearing, Chain, Springs Volume 01.06 : Coated steel products Volume 01.08 : Fasteners, rolling element bearings Non-ferrous materials: Volume 02.01 : Copper and copper Alloys Volume 02.02 : Die-cast Metals, Aluminium and Magnesium Alloys Volume 02.04 : Nonferrous Metals-Nickel, Lead, Tin Alloys, Precious, Primary, Reactive Metals Volume 02.05 :Metallic and inorganic coating: metal powders, sintered P/M, structural parts Metals Test Method and Analytical Procedures Volume 03.01 : Metals-Mechanical Testing, Elevated and low temperature Tests, Metallography Volume 03.02 : Wear and Erosion, Metal Corrosion Volume 03.03: Nondestructive Testing. Plastics Volume 08.01 : Plastics (I) : D 256 - D 2343 Volume 08.02 : Plastics (II) : D 2383 - D 4322 Volume 08.03 : Plastics (III) : D 4329 Latest Volume 08.04: Plastics pipe and building products. Volume 09.02, Rubber Products, Industrial Specifications and Related ASTM,Section 9 Test Methods ; Gasketts; Tires ASTM,Section 15 Volume 15.01- Refractories, Activated Carbon ; Advanced Ceramics ASTM DS -561 Metals & alloys in Unified Numbering System ASTM DS 67B Handbook of Comparative World steel Standards: Third Edition ASTM dictionary of Engineering science & Technology BS EN 558 Part 1 & 2 :Specification for face to face/ end to end dimensions of valves
MECHANICAL Sl. No. 147 148 149 150
CODES / STANDARDS BS EN 593 BS 970 BS PD 970 BS 1113
151 BS EN 1171 152 BS 1414 153 154 155 156 157 158 159 160 161 162 163 164
BS 1500 BS 1501 BS 1507, 1508 BS 1515 BS 1560 BS EN 1759 BS 1832 BS 1868 BS 1873 BS 1902 BS 2600 BS 3381
166 BS 3799 167 BS 4592 168 BS 5150 169 BS 5152 170 BS 5254 171 BS 5351 172 BS 5352 173 174 175 176 177
BS 5353 BS PD 5500 BS 6755 BS 7076-3 BS 8888
DESCRIPTION Specification for butterfly valves Part-1 & 2 : Specification for steel for forgings etc. Specification for Steel for forgings etc. Specification for water tube steam generation plant Specification for Flanged cast iron gate valves class 125 LBS, size 1-1/2" to 24" for petroleum industry Specification for Flanged and butt welding and steel gate valves for refinery services Fusion welded pressure Vessels –Part-I (CS & Low alloys steels) Specification for steels for fired and unfired pressure vessels-Plates Steel pipes, tubes for pressure vessels Specification for fusion welded pressure vessels Part 3:Section -1 to 3 : Specification for steel pipe flanges Part-1 & 3: Specification for steel pipe flange Compressed asbestos fiber jointing Specification for Flanged check valves for petroleum industry Specification for Flange steel globe valve for petroleum industry Methods of testing refractory materials Radiographic Examination of fusion welded butt joints Specification for Metallic spiral wound gaskets Part I: Spec. for seamless and ERW including induction welding technology Part II: Spec. for longitudinally arc welded tubes Specification for Socket weld and screwed end fittings Industrial open type metal flooring and stair treads Specification for Flanged cast iron gate valves, Class 125 LBS, size 11/2" to 24" for petroleum industry Specification for cast iron globe , globe stop and check valves Specification for polypropylene waste and fittings Specification for Steel ball valves for petroleum industry Specification for steel wedge, gate, globe and check valves for 50 mm and smaller for petroleum industry Specification for plug valves Specification for Unfired fusion Welded Pressure Vessels Part I & II : Testing of valves Dimensions of gasket for flanges to BS 1560 Technical product Specification
MECHANICAL Sl. No. CODES / STANDARDS 178 179 180 181 182 183 184 185 186 187 188 189 190
BS EN 10089 BS EN 10090 BS CP 10121 BS EN 10277 BS EN 10278 BS EN ISO 10497 BS EN 12266 BS EN 12334 BS EN ISO 10434 BS EN 12560-1 BS EN 12627 BS EN 13397 BS EN 13789
191
BS EN ISO 15761
192
BS EN ISO 17292
193
BS EN 60688
194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209
MSS-SP-6 MSS-SP-9 MSS-SP-25 MSS-SP-43 MSS-SP-44 MSS-SP-45 MSS-SP-54 MSS-SP-58 MSS-SP-61 MSS-SP-67 MSS-SP-68 MSS-SP-69 MSS-SP-75 MSS-SP-90 MSS-SP-95 ISO 3511
DESCRIPTION Hot rolled steels for quenched & tempered springs Specification for Steel for forgings etc. Code of practice for Cathodic protection Part-1 to 5 : Specification for steel for forgings etc. Specification for steel for forgings etc. Testing of valves Part-1 & 2: Testing of valves Specification for cast iron check valves, swing type Specification for Flanged and butt welding and refinery services Part 1, 4 & 5: Dimensions of gasket for flanges to BS 1560 Specification for Face to Face/ End to End dimensions of valves Specification for diaphragm valves Specification for cast iron globe, globe stop and check valve Specification for steel wedge, gate, globe and check valve for 50mm and smaller for petroleum industry Metal ball valves for the petroleum, petrochemical and allied industries Electrical measuring transducers for converting AC electrical quantities to analogue or digital signals Standard finishes for contact surface for flange Bronze and Iron flanges Standard marking systems. Stainless steel fittings Steel pipe line flanges(26" & larger) By-pass and drain connections Quality standard for fittings and flanges. Materials, Design and Manufacture of pipe hangers and supports Codes for testing of valves Butterfly valves High pressure offset seat butterfly valves Pipe hangers and supports -Selection and applications High test rough welding fittings Guidelines on Terminology for pipe hangers and supports Swage(D) Nipple and Bull plugs Part-1 to 4: Process measurement control, functions and instruments
MECHANICAL Sl. No. 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227
CODES / STANDARDS
DESCRIPTION
ISO 5167 Measurement of fluid flow. ISO 7240 Fire detection and alarm systems. ISO 8421 Part-3 & 5: Fire protection-Vocabulary: Fire detection & alarm IBR Indian Boilers Regulation 1950 WRC BUL 107 Local Stresses in Spherical and Cylindrical Shells due to External loadings WRC BUL 297 Local Stresses in Cylindrical Shells due to External Loading on Nozzles TEMA Hand Book EJMA Hand Book CORROSION AND INSULATION STANDARDS IS 277 Specification of Galvanized steel sheets(Plain and corrugated) IS 2629 Recommended practice for hot dip galvanizing of iron and steel IS 3144 Specification of Mineral Wool Thermal Insulation of materials-method of test IS 5905 Specification of sprayed aluminium and zinc coatings on iron and steel IS 6586 Recommended practice for metal spraying for protection of iron and steel Specification of Preformed Calcium Silicate Insulation (For temperature up to IS 8154 650 deg C) IS 8183 Specification of Bonded Mineral Wool IS 9842 Specification of Preformed Fibrous Pipe Insulation Industrial Application and finishing of thermal insulation materials at IS 14164 temperature above -80 deg C and up to 700 deg C-code of practice IS 14246 Specification of Continuously pre- painted galvanized steel sheets and coils
CIVIL
Sl. CODE / STANDARDS DESCRIPTION No. Bureau of Indian 1 Hand book on concrete reinforcement and detailing. standards. Bureau of Indian Handbook of typified designs for structures with steel roof 2 standards. trusses(With and without cranes)(Based on IS Codes) 3 CPWD Central Public Works Department Specification. 4 Hand Book of Civil Engineering 5 MOST Standards(Ministry of Surface Transport) National Building Code 6 Bureau of Indian standards. Of India 1983.Group 1 IRC 5(Indian Road 7 Bridges and Culvert Design Congress) 8 IRC 6 Bridges and Culvert Design 9 IRC 18 Bridges and Culvert Design 10 IRC 81 Bridges and Culvert Design 11 IS 6 Specification for moderate heat duty fireclay refractories, group 'A'. 12 IS 8 High heat duty fireclay refractories-specification. 13 IS 73 Paving bitumen - Specification. 14 IS 217 Specification for cutback bitumen. 15 IS 225 Structural Steel 16 IS 269 Ordinary Portland Cement 17 IS 383 Coarse and fine aggregate from natural sources for concrete Specification for mild steel and medium tensile steel bars and hard 18 IS 432 drawn steel wire for concrete reinforcement 19 IS 454 Cutback bitumen from waxy crude - specification. 20 IS 455 Portland Blast Furnace Slag Cement 21 IS 456 Plain and reinforced concrete-Code of Practice 22 IS 458 Specification for Pre Cast Concrete Pipes. 23 IS 702 Specification for industrial bitumen.
CIVIL
Sl. CODE / STANDARDS No.
DESCRIPTION Explanatory handbook on Indian standard code of practice for design loads (Other than earthquake) for buildings &structures: Part 3- Wind loads. Part 1: Code of practice for design loads (Other than earth quake) for buildings and structures Part 1: Dead loads - Unit weights of building materials and stored materials.
25
IS 1024
26
IS 1080
27 28 29 30
IS 1161 IS 1195 IS 1196 IS 1199
31
IS 1200
32 33 34 35 36
IS 1237 IS 1322 IS 1346 IS 1398 IS1489
37
IS 1498
Part 2: Code of practice for design loads(Other than earth quake) for buildings and structures Part 2: Imposed loads Part 3: Code of practice for design loads (Other than earth quake) for buildings and structures Part 3: Wind Loads. Part 4: Code of practice for design loads (Other than earth quake) for buildings and structures Part 4: Snow Loads. Part 5: Code of practice for design loads(Other than earth quake) for buildings and structures Part 5: Special loads & combinations Use of welding in bridges and structures subject to dynamic loading code of practice. Code of practice for design and construction of shallow foundations in soils (other than raft, ring and shell) Specification for steel tubes for structural purpose Bitumen - Mastic for Flooring - Specification. Code of practice for laying bitumen mastic flooring. Method of sampling and analysis of concrete Part 17: Method of measurement of building and civil engineering work. Specification for cement concrete flooring tiles Bitumen felts for water - proofing and damp - proofing - specification. Code of practice for water proofing of roofs with bitumen felts. Specification for packing paper water proof, bitumen - laminated. Portland Pozzolana Cement Classification & Identification of soils for general engineering purposes.
CIVIL CODE / Sl. No. STANDARDS
DESCRIPTION Part I: Methods of sampling & Physical test for refractory materials. Determination of pyrometric cone equivalent (PCE) or softening point. Part II: Methods of sampling & Physical test for refractory materials. Determination of refractoriness under loads. Part 3: Methods of sampling & Physical test for refractory materials. Determination of spalling resistance. Part IV: Methods of sampling & Physical test for refractory materials. Determination of cold crushing strength. Part 5: Methods of sampling & Physical test for refractory materials. Determination of modulus of rupture at ambient temperature. Part VI: Methods of sampling & Physical test for refractory materials. Determination of permanent change after reheating. Part VII: Methods of sampling & Physical test for refractory materials. Methods of sampling and creating for conformity. Part VIII: Methods of sampling & Physical test for refractory materials. Determination of apparent porosity. Part 9: Methods of sampling & Physical test for refractory materials. Determination of specific gravity and true density. Part X: Methods of sampling & Physical test for refractory materials. Determination of size of refractory bricks. Part 11: Methods of sampling & Physical test for refractory materials. Determination of warpage Part XII: Methods of sampling & Physical test for refractory materials. Determination of bulk density. Part XIII: Methods of sampling & Physical test for refractory materials. Determination of resistance to the disintegrating effect of carbon monoxide Part XIV: Methods of sampling & Physical test for refractory materials. Determination of sieve analysis. Part 15: Methods of sampling & Physical test for refractory materials. Methods for determination of bulk density apparent porosity and true porosity of dense shaped refractory materials Part 16: Methods of sampling & Physical test for refractory materials. Determination of thermal conductivity up to 1250oC of dense and insulating refractory products according to the hot wire parallel method. Part 17: Methods of sampling & Physical test for refractory materials. Determination of cold crushing strength of shaped insulating refractory products. Part 18: Methods of sampling & Physical test for refractory materials. Determination of creep in compression. Part 19: Methods of sampling & Physical test for refractory materials. Determination of thermal expansion.
Part 20: Methods of sampling & Physical test for refractory materials. Determination of modulus of rupture at elevated temperature.
CIVIL Sl. CODE / STANDARDS DESCRIPTION No. 39 IS 1609 Damp - Proofing treatment using bitumen felts - code of practice. 40
IS 1725
Specification for soil based blocks used in general building construction.
41
IS 1786
Specification for high strength deformed steel bars and wires for concrete reinforcement Part I: Specification for performed fillers for expansion joint in concrete pavement and structures (Non extruding & resilient type). Bitumen Impregnated fiber.
43
IS 1888
44
IS 1893
45
IS 1900
46
IS 1904
48 49 50
IS 2131 IS 2386 IS 2408
Part 2: Specification for performed fillers for expansion joint in concrete pavement and structures (Non extruding & resilient type).CNSL ALDEHYDE Resin & Coconut Pith. Method of load test on soils. Part 1: Criteria for earthquake resistant design of structures. General provisions and buildings. Methods of tests for wood poles. Code of practice for design and construction of foundations in soils: General Requirements. Part 2: Specification for heater for bitumen (TAR) & emulsion. Bitumen Sprayer Part 3: Specification for heater for bitumen (TAR) Emulsion Methods for standard penetration test for soils Methods of test for aggregates of concrete Methods of static tests of timbers in structural sizes. Methods of test for soils: Part 1- preparation of dry soil samples for various tests. Methods of test for soils: Part II- Determination of water content. Methods of test for soils: Part III- Determination of specific gravity. Section 1: Fine grained soils. Methods of test for soils: Part III- Determination of specific gravity. Section 2: Fine, Medium & Coarse Grained Soils. Methods of test for soils: Part 4- Grain size analysis. Methods of test for soils: Part 5- Determination of liquid and plastic limit.
Methods of test for soils: Part VI- Determination of shrinkage factors. Methods of test for soils: Part VII- Determination of water content - dry density relation using light compaction
CIVIL Sl. CODE / No. STANDARDS
DESCRIPTION Methods of test for soils: Part 8- Determination of water content - dry density relation using heavy compaction Methods of test for soils: Part 9- Determination of dry density- moisture content relation by constant mass of soil method. Methods of test for soils: Part 10- Determination of unconfined compressive strength. Methods of test for soils: Part 11- Determination of the shear strength parameters of a specimen tested in unconsolidated undrained triaxial compression with out the measurement of pore water pressure. Methods of test for soils: Part XII- Determination of the shear strength parameters of soil from consolidated undrained triaxial compression test with measurement of pore water pressure. Methods of test for soils: Part 13: Direct shear test. Methods of test for soils: Part 14- determination of density index (Relative Density) of cohesion less soils. Methods of test for soils: Part 15- determination of consolidation properties. Methods of test for soils: Part XV- determination of consolidation properties. Methods of test for soils: Part 16- Laboratory determination of CBR Methods of test for soils: Part 17- Laboratory determination of permeability. Methods of test for soils: Part 18- determination of field moisture equivalent. Methods of test for soils: Part 19- determination of centrifuge moisture equivalent. Methods of test for soils: Part 20- determination of linear shrinkage Methods of test for soils: Part XXI- determination of total soluble solids. Methods of test for soils: Part XXII- determination of organic matter. Methods of test for soils: Part XXIII- determination of calcium carbonate Methods of test for soils: Part XXIV- determination of cat ion exchange capacity. Methods of test for soils: Part XXV- determination of silica sesquioxide ratio. Methods of test for soils: Part 26- determination of H value. Methods of test for soils: Part XXVII- determination of total soluble sulphates.
Methods of test for soils: Part XXVIII- determination of dry density of soils in-place, by the sand replacement method. Methods of test for soils: Part XXIX- determination of dry density of soils in-place, by the core- cutter method. Methods of test for soils: Part XXX- Laboratory vane shear test.
CIVIL Sl. CODE / No. STANDARDS
DESCRIPTION Methods of test for soils: Part 31- Field determination of California bearing ratio. Methods of test for soils: Part XXXIII- determination of the density in-place by the ring and water replacement method. Methods of test for soils: Part XXXIV- determination of soil in -place by rubber balloon method. Methods of test for soils: Part XXXV- Measurement of negative pore water pressure. Methods of test for soils: Part 36- Laboratory determination of permeability of granular of soil (Constant Head) Methods of test for soils: Part XXXVII- determination of sand equivalent value of soils and fine aggregates. Methods of test for soils: Part XXXVIII- compaction control test (Hilf method) Methods of test for soils: Part XXXIX- Direct shear test for soil containing gravel. Section I: Laboratory Test. Methods of test for soils: Part XXXIX- Direct shear test for soil containing gravel. Section 2: In - Situ Shear Test. Methods of test for soils: Part XL- Determination of free swell index of soils.
52
IS 2809
Methods of test for soils: Part XLI- Measurement of swelling pressure of soils. Glossary of terms and symbols relating to soil engineering. Code of practice for design & construction of pile foundations: Part I: Concrete Piles. Section I: Driven Cast in-Situ Concrete Piles. Code of practice for design & construction of pile foundations: Part I: Concrete Piles. Section 2: Bored Cast in-Situ Piles. Code of practice for design & construction of pile foundations: Part 1: Concrete Piles. Section 3: Driven Precast Concrete Piles. Code of practice for design & construction of pile foundations: Part 1: Concrete Piles. Section 4: Bored Precast Concrete Piles. Code of practice for design & construction of pile foundations: Part II: Timber piles
54
IS 3037
Code of practice for design & construction of pile foundations: Part III: Under Reamed Piles Code of practice for design & construction of pile foundations: Part 4: Load Test on piles Specification for bitumen mastic for use in water proofing of roofs.
CIVIL Sl. No. 55 56 57
CODE / DESCRIPTION STANDARDS IS 3085 Method of test for permeability of cement mortar and concrete IS 3087 Specification for wood particle boards (Medium Density for general purpose) IS 3117 Bitumen Emulsion for roads and allied applications (Anionic Type)-Specification
58
IS 3495
59
IS 3513
60 61
IS 4020 IS 4021
Methods of tests of burnt clay building bricks. Part 1: Determination of compressive strength. Part 2: Determination of water absorption. Part 3: Determination of efflorescence. Part 4: Determination of warpage. Specification for high and medium density wood - based laminates. Part IV: Sampling and tests. Parts 1 to 16: Door shutters - Methods of tests Specification for timber door, window and ventilator frame Methods of physical tests for Hydraulic cement: Part 1: Determination of fineness by dry sieving. Methods of physical tests for Hydraulic cement: Part 2: Determination of fineness by blaine air permeability method. Methods of physical tests for Hydraulic cement: Part 3: Determination of soundness. Methods of physical tests for Hydraulic cement: Part 4: Determination of consistency of standard cement paste Methods of physical tests for Hydraulic cement: Part 5: Determination of initial &final setting times. Methods of physical tests for Hydraulic cement: Part 6: Determination of compressive strength of hydraulic cement other than masonry cement. Methods of physical tests for Hydraulic cement: Part 7: Determination of compressive strength of hydraulic cement other than masonry cement. Methods of physical tests for Hydraulic cement: Part 8: Determination of transverse & compressive strength of plastic mortar using prism. Methods of physical tests for Hydraulic cement: Part 9: Determination of heat of hydration. Methods of physical tests for Hydraulic cement: Part 10: Determination of drying shrinkage. Methods of physical tests for Hydraulic cement: Part 11: Determination of density.
Methods of physical tests for Hydraulic cement: Part 12: Determination of air content of hydraulic cement mortar.
63
IS 4326
Methods of physical tests for Hydraulic cement: Part 13: measurement of water retentivity of masonry cement. Earthquake resistant design and construction of buildings - code of practice.
CIVIL Sl. CODE / No. STANDARDS
65 66
IS 4365 IS 4925
67
IS 4984
68
IS 4995
69 70
IS 4999 IS 5134
DESCRIPTION Methods of test for stabilized soils: Part I- Methods of sampling and preparation of stabilized soils for testing. Methods of test for stabilized soils: Part II- Determination of Moisture content of stabilized soil mixtures. Methods of test for stabilized soils: Part III- Test for determination of moisture content -dry density relation for stabilized soil mixtures. Methods of test for stabilized soils: Part IV- Wetting and drying, and freezing and thawing tests for compacted soil - cement mixtures. Methods of test for stabilized soils: Part V- Determination of unconfined compressive strength of stabilized soils. Methods of test for stabilized soils: Part VI- Flexural strength of soil - cement using simple beam with third - point loading. Methods of test for stabilized soils: Part VII- Determination of cement content of cement stabilized soils. Methods of test for stabilized soils: Part VIII- Determination of lime content of lime stabilized soils. Methods of test for stabilized soils: Part IX- Determination of the bituminous stabilizer content of bitumen and tar stabilized soils. Methods of test for stabilized soils: Part X- Test for soil - bituminous mixtures. Code of practice for application of bitumen mastic for waterproofing of roofs. Specification for concrete batching and milling plant High density polyethylene pipes for portable water supplies, sewage and industrial effluents Criteria for design of reinforced concrete bins for the storage of granular and powdery materials. Part I General requirements &assessment of bin loads. Recommendations for grouting of pervious soils. Specification for bitumen impregnated paper.
71
IS 5454
72
IS 5817
73 74 75 76 77
IS 5871 IS 6509 IS 7112 IS 7113 IS 7198
Method of sampling of clay building bricks Preparation and use of lime - pozzolana mixture concrete in buildings and roads code on practice. Specification for bitumen mastic for tanking and damp - proofing. Code of practice for installation of joints in concrete pavements. Criteria for design of cross - section for unlined canals in alluvial soil. Soil - cement lining for canals - code of practice. Code of practice for damp - proofing using bitumen mastic.
CIVIL Sl. CODE / No. STANDARDS
DESCRIPTION Code of practice for calculation of settlements of foundations: Part I- Shallow foundations subjected to symmetrical static vertical loads. Bitumen emulsion for roads (cationic type) - specification. Guide for laying lining of canals with hot bitumen or bituminous felts. Specification for liquid limit apparatus for soils. Methods of test for abrasion resistance of concrete Guidelines for lining of canals in expansive soils. Specification for bitumen mastic, acid- resisting grade, Specification for CBR Moulds and its Accessories. Guide for lateral dynamic load test on piles. Code of practice for field control of moisture & compaction of soils for embankment and sub grade. Glossary of terms on soil and water. Vault (Strong Room) Doors: Part 3- Tests for fire resistance. Specification for equipment for determination of liquid limit of soils cone penetration method.
78
IS 8009
79 80 81 82 83 84 85 86
IS 8887 IS 9097 IS 9259 IS 9284 IS 9451 IS 9510 IS 9669 IS 9716
87
IS 10379
88 89
IS 11077 IS 11188
90
IS 11196
91
IS 11209
Specification for mould assembly for determination of permeability of soils.
92 93
IS 11229 IS 12583
Specification for shear box for testing of soils. Specification for corrugated bitumen roofing sheets.
94
IS 12778
Hot rolled parallel flange steel sections for beams, columns & section properties.
95
IS 12894
96
IS 13468
Specification for pulverized fuel ash-lime bricks Apparatus for determination of dry density of soil by core cutter method specification.
97 98
IS 13620 IS 13630
99
IS 13829
100 IS 13830 101 IS 13831
Fusion bonded epoxy coated reinforcing bars Ceramic Tiles-method of test Pesticide - Method for determination of residues in agricultural and food commodities, soil &water - atrazine and simazine. Pesticide - Method for determination of residues in agricultural and food commodities, soil & water - captafol. Pesticide - Method for determination of residues in agricultural and food commodities, soil & water - acephate and its toxic metabolite methamidofos.
CIVIL
Sl. CODE / No. STANDARDS
DESCRIPTION
102 IS 14374
Refractories for chimney
103 IS 14593
Design & construction of bored cast - in - situ piles founded on rocks - guidelines.
104 IS 14683
Agricultural tractors and machinery - lighting devices for travel on public roads.
105 IS 14765
Determination of water retention capacity in soil - Method of test. Aggregate size distribution & water stability of soil aggregates - Method for determination. Non - Destructive integrity testing of piles (NDT) - guidelines. Hand book for structural engineers :( 1)-Structural steel sections. Hand book for structural engineers :( 2)-Steel beams and plate girders. Hand book for structural engineers :( 3)-Steel columns and struts. Hand book for structural engineers :( 4)-use of high strength friction grip bolts. Hand book for structural engineers :( 5)-Cold - Formed, Light - Gauge steel structures. Hand book for structural engineers :( 6)-Application of plastic theory in design of steel structures. Hand book for structural engineers :( 7)-Simple welded girders. ISI Hand Book of Mathematical physical, chemical & Engineering tables. Design aids for reinforced concrete Hand Book of method of measurement of Building Works
106 IS 14766 107 108 109 110 111
IS 14893 SP:6(1) SP:6(2) SP:6(3) SP:6(4)
112 SP:6(5) 113 SP:6(6) 114 115 116 117
SP:6(7) SP: 8 SP 16 SP 27
118 SP 24
Explanatory hand book on Indian Standard Code of Practice for plain and reinforced concrete
ELECTRICAL Sl. CODES / No. STANDARDS
2 3 4 5 6
IS 325 IS 335 IS 374 IS 732 IS 900
7
IS 1255
8 9 10
IS 1271 IS 1415 IS 1416
12
IS 1576
13
IS 1866
DESCRIPTION Part 2 : Miniature Fuses : Cartridge Fuse Links - Specification Part 6: Miniature Fuses : Fuse Holders for Miniature Cartridge Fuse links Three - Phase induction Motors New insulating oils Electric Ceiling type Fans and Regulators Code of Practice of Electrical Wiring installations Code of Practice for Installation and Maintenance of Induction Motors Code of Practice for Installation and Maintenance of Induction Motors up to and including 33 kv rating. Thermal Evaluation and classification of electrical insulation Electric Hand Lamps Safety Transformers Part 1: Specification for PVC Insulated (Heavy Duty) Electric Cables Part 2: PVC Insulated (Heavy Duty) Electric Cables - Part 2 : for working Voltages from 3"3kv up to and including11 kv Solid pressboard for electrical purpose - specification Code of Practice for electrical Maintenance and Supervision of Mineral Insulating Oil in Equipment Power transformers: Part 1 General Power transformers: Part 2 Temperature Power transformers: Part 3 Insulation level and dielectric tests
15
IS 2148
17
IS 2309
18
IS 2448
Power transformers: Part 4 Terminal marking, tappings and connections Power transformers: Part 5 Terminal / Reactors bushing minimum external clearance in air-specification Specification for Flameproof Enclosures of Electrical Apparatus Part 1: Flameproof Electric Lighting Fittings: Part 1 Well-glass and Bulkhead types Part 2: Flameproof Electric Lighting Fittings: Part 2 Fitting using Glass Tubes Part 3: Flameproof Electric Lighting Fittings: Part 3 Fitting using Fluorescent lamps and plastic covers. Part 4: Flameproof Electric Lighting Fittings: Part 4 Portable Flame-proof Hand lamps and Approved Flexible Cables Code of Practice for the Protection of Buildings and allied structures against lighting Part 1: Adhesive Insulating Tapes for Electrical purposes: Part 1 Tapes with cotton Textiles Substrates
ELECTRICAL Sl. CODES / DESCRIPTION No. STANDARDS 19 IS 2551 Danger Notice Plates 20 IS 2584 Method of test for electric strength of solid insulating materials at power frequencies Part 1: Current Transformers: General Requirements Part 2: Current Transformers: Measuring Current Transformers Part 3: Current Transformers: Protective Current Transformers 22 IS 3043 Code of Practice for Earthling Part 2: Voltage Transformers: Measuring Voltage Transformers Part 3: Voltage Transformers: Protective Voltage Transformers Part 4: Voltage Transformers: Capacitor Voltage Transformers Part 0: Electrical Relays for Power Systems Protection: General Introduction and list 24 IS 3231 of Parts 25 IS 3639 Specification for Fittings and Accessories for Power Transformers Part 1: Code of Practice for interior Illumination: General requirements and recommendations for working interiors Part 2: Code of Practice for interior Illumination: Schedule for valves of Illumination and Glare Index Part 2: Recommended current ratings for Cables: PVC insulated and PVC sheathed 27 IS 3961 heavy duty cables 28 IS 3975 Specification for Mild steel wires, Strips and Tapes for Armoring of Cables 29 IS 4029 Guide for Testing Three-phase Induction Motors 30 IS 4146 Application guide for voltage transformers 31 IS 4201 Application guide for Current transformers 32 IS 4691 Degree of protection provided by enclosure for Rotating Electrical Machinery 33 IS 4889 Methods of Determination of Efficiency of Rotating Electrical Machines Part 1: Recommendations on safety Procedures and Practices in Electrical work: General Part 2: Recommendations on safety Procedures and Practices in Electrical work: Life Saving Techniques 35 IS 5424 Specification for Rubber Mats for Electrical purpose 36 IS 5553 Specifications for Reactors: Part 5: tuning reactors 37 IS 5571 Guide for Selection of Electrical Equipment for Hazardous Areas Classification of Hazardous Areas (other than; mines) having flammable Gases and 38 IS 5572 Vapors for Electrical Installation 39 IS 5780 Specification for Intrinsically Safe Electrical Apparatus and Circuits
ELECTRICAL Sl. No. 40 41 42 43 44 45 46 47
CODES / STANDARDS IS 5819 IS 5831 IS 6209 IS 6381 IS 6600 IS 6665 IS 6792 IS 6949
48
IS 7098
49 50 51 52 53 54
IS 7132 IS 7689 IS 7816 IS 8130 IS 8224 IS 8289
55
IS 8308
56
IS 8468
57
IS 8603
59 60 61
IS 8690 IS 9223 IS 9334
62
IS 9409
63
IS 9570
64 65
IS 9583 IS 9628
DESCRIPTION Recommended Short-circuit Ratings of High Voltage PVC cables Specification for PVC Insulation and sheath of Electric Cables. Methods for Partial Discharge Measurements Construction and Testing of Electrical Apparatus with type of protection 'e' Guide for loading of Oil immersed Transformers Code of practice for Industrial Lighting Method for Determination of Electric Strength of Insulating Oils Summation current transformers Cross linked Polyethylene Insulated PVC Sheathed Cables: Part 2 for working voltages form 3.3kv up to and including 33kv Guide for testing synchronous machines Guide for the control of undesirable Static Electricity Guide for Testing Insulation Resistance of Rotating ;Machines Specification for Conductors for Insulation Electric Cables & Flexible Cords Electric Lighting Fittings for Division 2 Areas Electric Equipment with type of protection 'n' Compression type Tubular in-line connectors for Aluminum Conductors of Insulated Cables On-load tap chargers Dimensions for porcelain transformers bushings for use in heavily polluted atmosphere: part 1: 12kv and 17.5 kv bushings Part 1: Specification for Low-voltage Switchgear and Control gear Assemblies : Requirements for Type - tested and partially typed tested assemblies Part 2: Specification for Low-voltage Switchgear and Control gear Assemblies : Particular Requirements for Busbar trunking systems (busways) Part 3: Specification for Low-voltage Switchgear and Control gear Assemblies : Particular Requirements for Equipment where unskilled persons have access for their use Application guide for measuring devices for high voltage testing Portable Earth Resistance Meters Specification for Electric Motor Operated Actuators Classification of Electrical and Electronic Equipment with regard to protection against Electric Shock Classification of Flammable Gases or Vapors with Air according to their maximum experimental safe gaps and ;minimum igniting currents Specification for Emergency Lighting Units Three-phase Induction Motors with type of protection 'n'
ELECTRICAL Sl. No.
CODES / STANDARDS
66
IS 9677
67
IS 9678
68
IS 9947
71
IS 10322
72
IS 10418
73
IS 10462
74
IS 10593
76
IS 10893
DESCRIPTION Guide for limits of temperature rise of the windings of electrical equipment when tested by different methods Methods of measuring temperature rise of electrical equipment Tests Methods for Evaluating Resistance to Tracking and Erosion of Electrical Insulating Materials used under severe Ambient conditions Part 1: Code of Practice for Selection, Installation and Maintenance of Transformers : Selection Part 2: Code of Practice for Selection, Installation and Maintenance of Transformers : Installation (superseding IS:1886) Part 3: Code of Practice for Selection, Installation and Maintenance of Transformers : Maintenance (superseding IS : 1886) Part 1: Code of practice for Selection, Installation and Maintenance of Switch gear and Control gear : General Part 2 : Code of practice for Selection, Installation and Maintenance of Switch gear and Control gear : Selection Part 3: Code of practice for Selection, Installation and Maintenance of Switch gear and Control gear : Installation Part 4: Code of practice for Selection, Installation and Maintenance of Switch gear and Control gear : Maintenance Luminaries: Part 5 Particular requirements, Section 3 Luminaries for road and street lighting [superseding IS:2149] Drums for Electric Cables Part 1: Fictitious calculation method for Determination of Dimensions of protective coverings of Cables Method of evaluating the analysis of gases in oil filled electrical equipment in service Part 40: Methods of Test for Cables : Uniformity of zinc coating on steel armours Part 41: Methods of Test for Cables : Mass of zinc coating on steel armours Part 43: Methods of Test for Cables : Insulation Resistance Part 45: Methods of Test for Cables : High Voltage Test Part 46: Methods of Test for Cables : Partial discharge Test Part 47: Methods of Test for Cables : Impulse Test Part 53: Methods of Tests for Cables: Flammability Test Part 58: Methods of Tests for Cables: Oxygen Index Test Part 59: Methods of Test for Cables: Determination of halogen acid gas evolved during combustion of polymeric materials taken from cables. Part 61: Methods of Tests for Cables: Flame retardant test Part 62: Methods of Tests for Cables: Flame retardant test for bunched cables Part 63: Methods of Test for Cables : Smoke density of electric cables under fire conditions Specification for Sealed Nickel Cadmium Button Type Rechargeable Single Cells
ELECTRICAL Sl. CODES / No. STANDARDS 77 IS 10918 78 IS 11171 79
IS 11182
80 81 82 83
IS 11322 IS 11530 IS 11548 IS 11697
84
IS 12021
85
IS 12063
86
IS 12360
87
IS 12615
89
IS 12729
90 91 92
IS 12802 IS 12943 IS 12974
93
IS 13032
94 95 96 97
IS 13072 IS 13118 IS 13203 IS 13346
99
IS 13408
DESCRIPTION Vented type nickel cadmium batteries Specification for Dry-Type Power Transformers Part 1: Guide for evaluation of Insulation systems of electrical equipment: Identification, evaluation and ageing mechanisms Method for partial discharge measurement in instrument transformers Specification for Voltage Grading Capacitor Capacitors for Surge Protection use in Voltage system above 650V and up to 33kv Guide for determination of lighting impulse electric strength of insulating liquids Specification for Control Transformers for Switchgear and Control gear for Voltages not exceeding 1000 V ac Classification of Degrees of Protection provided by enclosures of Electrical Equipment Voltage Bands for Electrical Installations including Preferred Voltages and Frequency Induction Motors - Energy Efficient, Three-phase, Squirrel Cage - Specification Residual Current Operated Circuit Breakers-Specification Residual Current Operated Circuit Breakers for Household and Similar Uses - Part 1 : Circuit Breakers Without Integral Over current Protective Residual Current Operated Circuit Breakers for Household and Similar Uses - Part 2 : Circuit Breakers With Integral Over current Protection General requirements for Switchgear and Control gear for voltages exceeding 1000v Temperature-rise Measurements of Rotating Electrical Machines Bras Glands for PVC Cables Semiconductor Contactors - Specification Ac miniature Circuit-Breaker Boards for Voltages not Exceeding 1000V Specification Sulphur Hexafluoride for Electrical purposes Specification for High - Voltage Alternating - Current Circuit - Breakers Method for Verifying Accuracy of an Delta Measurements General Requirements for Electrical Apparatus for Explosive Gas Atmospheres Methods of photometry of luminaries: Part 2 luminaries For road and street Lighting Photometry of Luminaries: Methods of Measurement- Part 3: luminaries For Floodlighting. Part 1: Code of Practice for Selection, Installation and maintenance of Electrical Apparatus for Use in Potentially Explosive Atmospheres
ELECTRICAL Sl. CODES / DESCRIPTION No. STANDARDS 100 IS 13503 General Classification of Insulating Liquids Test Procedure for Measurement of Loss Tangent Angle of Coils and Bars for 101 IS 13508 Machine Winding - Guide Guide for Selection and Application of 3-phase AC. Induction Motors for Different 102 IS 13555 Types of Driven Equipment Joints and Terminations of Polymeric Cables for Working Voltages from 6.6 kv up 103 IS 13573 to and including 33 kv - Performance Requirements and Type Tests Part 1: Specification for low-voltage Switchgear and Control gear: General Rules Part 2: Specification for low-voltage Switchgear and Control gear: Circuit Breakers Part 3: Specification for low-voltage Switchgear and Control gear: Switches, Disconnectors, Switch Disconnectors and fuse combination units Part 4: Specification for low-voltage Switchgear and Control gear : Contractors and Motors Starters Part 5: Specification for low-voltage Switchgear and Control gear: Control Circuit Devices and Switching elements 105 IS 13956 Testing transformers Specification for Three-phase Induction Motors for Fans Used in Air-conditioning 106 IS 14377 and Ventilation AC Static Transformer Operated Watt-hour and Var-hour Meter, Class 0.2 S and 107 IS 14697 0.5 S - Specification 108 IS 14993 Saddles, Pole Clamps[Stick Clamps] and Accessories for Live Working Part 1: Electrical Resistance Trace heating in Potentially Explosive Atmospheres: General and Testing Requirements Part 2: Electrical Resistance Trace heating in Potentially Explosive Atmospheres: Informative Application Guide for Design, Installation 110 SP 30 National Electric Code 111 SP 31 Methods of Artificial Respiration 112 IE Rules The Indian Electricity Rules, 1956
INSTRUMENTATION Sl No CODE / STANDARDS 1
API RP 14 B
2
API 500
3 4 5 6
API RP 551 API RP 552 API RP 553 API STD 589
7
API STD 670
8
API PUBL 2031
9 10 11 12 13 14 15 16
API RP 2210 API 51101 API 52534 ASME PTC 19 ASME Code ASME B 40 ASTM D-68-74 ASTM D-1047
17
ASTM D-2843
18
ASTM D-2863
19 20
BS 1042 BS 4994
21
BS 5308
22
DIN 19213
23
DIN 43729
24 25 26
DIN 43760 Part A EEMUA EN 50014 & 50018-
DESCRIPTION Design installation repair and operation of safety valves system Recommended practice for classification location for petroleum facility as Class : Division I & Division II Process measurement instrumentation Transmission systems Refinery control valves Fire Test for evaluation of valve system packing Machinery protection system vibration, axial position & bearing temperature monitoring systems Combustible gas detector systems and environmental and operational factors influencing their performance. Flame arresters for vents of tank storing petroleum products PD Meters Turbine Meter Instruments and apparatus; Part 3: Temperature measurement. Section VIII,Division 1: boiler and pressure vessel code Pressure Gauges Copper Tube Copper Tube PVC Cover Standard test method for density of smoke from the burning or decomposition of plastics Test method for measuring minimum oxygen concentration to support candle like combustion of plastic(Oxygen Index) Orifice Plates FRP Cable Trays Part-I: Specification of polyethylene cables. Part-II: Specification for PVC insulated cables. Flow measurement; connections of differential pressure instruments and direct flanged shut-off valves up to PB 400bar. Electrical temperature sensors; connection heads for thermocouple thermometers and resistance thermometers Temperature Vs resistance curves Publication 138 for sample line calculations. Solenoid valve switches/field transmitter with separate power/local
EX.Proof Protection
panel, IR HC detector.
INSTRUMENTATION Sl No 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
CODE / STANDARDS
DESCRIPTION
EN 50014 & EN.50020-Intrinsic All transmitters. safe Protection EN 50014 & Local panels wherever Ex. Proof is not applicable. EN500016-purging Electrical apparatus for potentially explosive atmosphere-flame proof EN 50018 enclosure 'd' IEC 79 Electrical Apparatus for Explosive Gas Atmosphere. IEC 332 Cables Extruded solid dielectric insulated power cables for rated voltages from I IEC 502 kv up to 30 kv. IEC 529 IP 55 IEC 529 IP 65 IEC 529 IP 65 IEC 529 IP 65(IP 55 for pressurized panels) IEC 529 IP 65 IEC 529 IP 55 IEC 540 & 540A Test method for insulation and sheathing of electric cables. IEC 534-2 Industrial Process Control valves. Thermocouple and compensating cables, tolerances and identification IEC 584, Part 2& 3 system. IEC 751 Industrial Platinum resistance thermometer sensor. IEC 757 Code for designation of colors. IEC 902 Industrial process measurement and definitions. Electromagnetic compatibility for industrial process measurement and IEC 1000 control Equipment. IEC 60092 Electric insulation of cables IEC 30331 Test of fire resistant cables. IEC 60332 Tests on bunched wires and cables. IEC 60584-3 Extension and compensating cables-tolerances and identification Test on gases evolved during combustion of material from cables-Part-1, IEC 60754 2. IS 2633 Method of testing: Uniformity of coating on zinc coated articles.
52 53 54 55
IS 3624 IS 3961 IS 6746 IS 7358
Specification for pressure & vacuum gauges. FRP Cable Trays Specification for thermocouples.
INSTRUMENTATION Sl No
CODE / STANDARDS
DESCRIPTION
56
IS 8239 - EX Proof
57
IS 8784
Solenoid valve/Switches/field transmitter with separate power/local panel / junction boxes/cable glands as applicable. Thermocouple compensating cables.
58
IS 13346
Electrical apparatus for explosive gas atmosphere-general requirements.
59
IS 13947
Part I to V: Specification of low voltage switch gear & control gear.
60
ISA S 5.2
61
ISA MC 96.1
62
ISO 2715
63
ISO 3966
64
ISO 5167 / BS 1042
65 66
NFPA 72 NFPA 496
67
NEMA
68
RAL ST 322
Binary logic diagrams for process operations. American National Standard for temperature measurement thermocouples Turbine meter systems. Measurement of fluid flow in closed conduit, part 2,velocity area methods,subsection2.1,method using pitot static tubes Measurement of fluid flow by means of pressure differential devices, Part 1, Orifice plates, nozzles and venturi tubes in circular cross-section conduits running full. Smoke Detection System Pressurized shelter for analyzer National electric manufacturers association- ICS-6 enclosures for industrial control and systems. Register of color codes.
FIRE AND SAFETY SL. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
CODE / DESCRIPTION STANDARDS IS 636 Specification for non-percolating flexible fire fighting delivery hose IS 884 Specification for first - aid hose reel for fire fighting Specification for couplings, double male and double female, instantaneous IS 901 pattern for fire fighting IS 902 Specification for suction hose couplings for fire fighting purposes Specification for fire hose delivery coupling, branch pipe, nozzles and nozzles IS 903 spanner Specification for 2-way and 3-way suction collecting heads for fire fighting IS 904 purposes Specification for delivery breechings, dividing and collecting instantaneous IS 905 pattern for fire fighting purposes IS 906 Specification for revolving branch pipe for fire fighting purposes IS 907 Specification for suction strainers cylindrical type for fire fighting purposes IS 908 Specification for fire hydrant, stand post type IS 910 Specification for combined key for hydrant , hydrant cover and lower value IS 926 Specification for fire man's axe IS 927 Specification for fire hooks IS 928 Specification for fire bells IS 937 Specification for washer for water fittings for fire fighting purposes IS 940 Specification for portable fire extinguisher, water type (gas cartridge) IS 941 Specification for blower and exchanger for fire fighting IS 942 Functional requirements for 275-I /min portable pump set for fire fighting IS 944 Functional requirements for 1800-I/min trailer pump for fire brigade use IS 948 Functional requirements for water tender type, A for fire brigade use IS 949 Functional requirements for emergency(rescue) tender for fire brigade use IS 950 Functional requirement for water tender type-B for fire brigade use IS 951 Functional requirements for crash tender for air fields IS 952 Specification for fog nozzle for fire brigade use IS 955 Functional requirements for dry powder tender for fire brigade use Part I: Functional requirements for electric motor sirens : AC 3 phase 50 Hz, IS 1941 415 volts type
27 28
IS 2097 IS 2171
29
IS 2175
30
IS 2189
Specification for foam making branch pipe Specification for portable fire extinguishers, dry powder (cartridge type) Specification for heat sensitive fire detectors for use in automatic fire alarm system Code of practice for selection, installation and maintenance of automatic fire detection and alarm system
FIRE AND SAFETY SL. NO.
CODE / STANDARDS
31
IS 2190
32 33 34 35 36
IS 2298 IS 2546 IS 2696 IS 2745 IS 2871
37
IS 2878
38 39 40
IS 2925 IS 2930 IS 3582
42 43 44
IS 3744 IS 3808 IS 3809
45
IS 3844
46
IS 4226
47 48 49 50 51 52
IS 4264 IS 4308 IS 4861 IS 4862 IS 4928 IS 4947
DESCRIPTION Code of practice for selection, installation and maintenance of portable firstaid fire extinguishers Specification for single barrel stirr up pump for fire fighting purposes Specification for Galvanized mild steel fire bucket Functional requirements for 1 125 - 1 /min light fire engine Specification for non - metal helmet for fireman and civil defence personnel Specification for branch pipe universal for fire fighting purposes Specification for fire extinguisher, carbon dioxide type (portable and trolley mounted) Specification for industrial safety helmets Functional requirements for hose laying tender for fire brigade use Specification for basket strainers for fire fighting purposes (cylindrical type ) Part I: Specification for fire check door part : plate metal covered and rolling type Part II: Specification for metallic and non-metallic fire check doors Resistance test and performance criteria Specification for house binding machine Method of test for non-combustibility of building materials Fire resistance test for structures(first revision) code of practice for installation and maintenance of internal fire hydrants and hose reels on premises code of practice for fire safety of industrial building : Aluminium/Magnesium powder factories Code of safety for caustic soda Specification for dry chemical powder for fighting B & C class fires Specification for dry powder for fighting fires in burning metals(first revision) Part I: Specification for portable fire extinguishers for aircraft Specification for delivery valve for centrifugal fire pump outlets Specification for gas cartridges for use in fire extinguishers
53
IS 4989
54 55 56 57
IS 5131 IS 5290 IS 5505 IS 5612
Part-I to IV: Specification for foam concentrate(compound) for producing foam for fire fighting : Part 3 Fluoro protein foam Specification for dividing breeching with control for fire brigade use Specification for landing valves (third revision) Specification for multi - edged rescue axe(non- wedging) (first revision) Part II:Specification for hose - clamps and hose bandages for fire brigade use
FIRE AND SAFETY SL. CODE / DESCRIPTION NO. STANDARDS 58 IS 5714 Specification for hydrant, stand- pipe for fire fighting 59 IS 5888 Code of practice for design and construction of fire service drill - tower Part-II & III: Code of practice for selection, operation and maintenance of 60 IS 5896 special fire fighting appliances 61 IS 6026 Specification for hand operated sirens (first revision) Code of practice for selection, operation and maintenance of trailer fire 62 IS 6070 pumps, portable pumps water tenders and motor fire engines 63 IS 6234 Specification for portable fire extinguisher, water type (stored pressure) code of practice for design and installation of fixed carbon dioxide for fire 64 IS 6382 extinguishing system 65 IS 6818 Code for safety for phosphoric Acid 66 IS 6819 Code for safety for calcium carbide 67 IS 6953 Code for safety for bromine Specification for couplings, branch pipe, nozzle, used in hose reel tubing for 68 IS 8090 fire fighting 69 IS 8442 Functional requirements for stand post type water monitor for fire fighting Part II: Specification for valve fittings for use with LPG cylinders more than 5 70 IS 8737 ltrs capacity Recommendation for fire precautionary measures in the construction of 71 IS 8758 temporary structures and pandas Code of practice for provision and maintenance of water supplies and fire 72 IS 9668 fighting 73 IS 9972 Specification for automatic sprinkler heads for fire protection service 74 IS 10204 Specification for portable fire extinguisher mechanical foam type Functional requirements for small foam tender for fire brigade use(with 75 IS 10460 Amendment No. 1)
76
IS 10658
77
IS 10993
78 79 80
IS 11070 IS 11101 IS 11108
Specification for higher capacity dry powder fire extinguisher (Trolley Mounted) Functional requirements for 2000 kg dry powder tender for fire brigade use(with Amendment No. 1) Specification for bromochlorodifluoromethane (halon-1211) for fire fighting Specification for extended branch pipe for fire brigade use Specification for portable fire extinguisher halons - 1211 type
FIRE AND SAFETY SL. NO.
CODE / STANDARDS
81
IS 11360
82 83 84 85
IS 11457 IS 11833 IS 12349 IS 12407
86
IS 12456
87
IS 12458
88
IS 12717
89
IS 12835
90 91 92
IS 12861 IS 13039 IS 13045
93
IS 13385
94
IS 13849
95 96
IS 15394 OISD-STD-105
97
OISD-STD-106
98
OISD-RP-108
DESCRIPTION Specification for smoke detection for use in automatic electrical fire alarm system Part-I: Code of practice for fire safety of chemical industries Specification for dry power fire extinguisher for metal fires Fire protection - safety sings Graphic symbols for fire protection plans Code of practice for fire protection of electronic data processing installation Method of test for fire resistance test of fire stops Functional requirements of fire fighting equipment - High capacity portable pump set Part I: Design and installation of fixed foam fire extinguisher system-code of practice Specification for fire fighting-double bit axe for forest fires External hydrant systems provision & maintenance-code of practice Code of practice for fire safety in industrial buildings Specification for fire extinguisher 50 ltrs capacity wheel mounted water type(Gas cartridge) Specification for portable fire extinguisher dry powder type ( stored pressure) Fire safety in petroleum refineries & fertilizer plants-code of practice Work Permit System Process design and operating philosophies on pressure relief and disposal system Recommended Practices on Oil Storage and Handling
99
OISD-STD-109
100 101 102
OISD-STD-110 OISD-STD-111 OISD-STD-112
103
OISD-STD-113
104
OISD-STD-114
105
OISD-GDN-115
Process Design and Operating philosophies on blow down and sewer system Recommended Practices on Static Electricity Process design and operating philosophies on fired process furnace Safe handling of air hydrocarbon mixtures and pyrophoric substances Classification of Area for electrical installations at Hydrocarbon processing and handling facilities Hazardous Chemicals and their handling Guidelines on Fire Fighting Equipment and Appliances in Petroleum Industry
FIRE AND SAFETY SL. NO.
CODE / STANDARDS
106
OISD-STD-116
107
OISD-STD-117
108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126
OISD-STD-118 OISD-STD-119 OISD-STD-120 OISD-STD-121 OISD-STD-122 OISD-STD-123 OISD-STD-124 OISD-RP-125 OISD-RP-126 OISD-STD-127 OISD-STD-128 OISD-STD-129 OISD-STD-130 OISD-STD-131 OISD-STD-132 OISD-STD-133 OISD-STD-134 OISD-STD-135 OISD-STD-137
DESCRIPTION Fire Protection facilities for Petroleum Refineries and Oil/Gas Processing Plants Fire Protection Facilities for Petroleum Depots and Terminals and pipeline installations Layouts for Oil and Gas Installations Inspection of Pumps Inspection of Compressors Inspection of turbines and Diesel Engines Inspection of fans, blowers, gear boxes and agitators Inspection of rotating equipment components Predictive Maintenance Practices Inspection and Maintenance of Mechanical Seals Specific maintenance practices for rotating equipment History recording of rotating equipment Inspection of unfired pressure vessels Inspection of storage tanks Inspection pipes, valves and fittings Inspection of Boilers Inspection of pressure relieving devices Inspection of fired heaters Inspection of heat exchangers Inspection of loading and unloading hoses for petroleum products Inspection of electrical equipment
127 128 129
OISD-STD-138 OISD-STD-139 OISD-STD-140
130
OISD-STD-141
131
OISD-STD-142
Inspection of cross country pipelines – Onshore Inspection of pipelines – Offshore Inspection of jetty pipelines Design and Construction requirements for cross country hydrocarbon pipelines Inspection of fire fighting equipments and systems Liquefied Petroleum Gas (LPG) Bottling Plant Operations Vol.-I Design Philosophies Vol.-II Operating Practices Vol.-III Inspection and Maintenance Practices Vol.-IV Safety and Fire Protection
FIRE AND SAFETY SL. NO. 133 134 135 136 137
CODE / STANDARDS OISD-GDN-145 OISD-RP-146 OISD-RP-147 OISD-RP-148 OISD-RP-149
138
OISD-STD-150
139 140
OISD-STD-151 OISD-STD-152
141
OISD-STD-153
142
144 145
OISD-STD-154 OISD-STD-155 OISD-STD-155 OISD-GDN-156 OISD-RP-157
146
OISD-RP-158
147
OISD-STD-159
148 149 150
OISD-STD-160 OISD-GDN-161 OISD-STD-162
DESCRIPTION Guidelines on Internal Safety Audits (Procedures and Checklist) Preservation of idle electrical equipment Inspection & safe practices during electrical installations Inspection & safe practices during overhauling electrical equipment Design aspects for safety in electrical systems Design and Safety Requirements For Liquefied Petroleum Gas Mounded Storage Facility Safety in Design, Fabrication and Fittings : Propane Tank Trucks Safety instrumentation for process system in hydrocarbon industry Maintenance & inspection of safety instrumentation in hydrocarbon industry Safety aspects in functional training Personal Protective Equipment Part I Non-respiratory equipment Part II Respiratory Equipment Fire Protection Facilities for Port Oil Terminals Recommended Practice for Transportation of Bulk Petroleum Products Recommended Practices on Storage and Handling of Bulk Liquefied Petroleum Gas” LPG Tank Trucks - Requirements of Safety on Design/Fabrication and Fittings Protection to fittings mounted on existing LPG tank trucks LPG Tank Truck Incidents : Rescue & Relief Operations Safety in installation and maintenance of LPG Cylinders Manifold
151 152
OISD-STD-163 OISD-STD-164
Process Control Room Safety Fire Proofing in Oil & Gas Industry
153
OISD-GDN-165
Guidelines for Rescue & Relief Operations for POL Tank Truck Accident
154 155 156
OISD-GDN-166 OISD-RP-167 OISD-GDN-168
157
OISD-GDN-169
158
OISD-STD-170
159 160
OISD-STD-171 OISD-STD-173
Guidelines for Occupational Health Monitoring in Oil and Gas Industry POL Tank lorry Design & Safety Emergency Preparedness Plan for Marketing Locations of Oil Industry OISD Guidelines on Small LPG Bottling Plants (Design and Fire Protection facilities) Inspection, Maintenance, Repairs and Rehabilitation of foundations and structures Preservation of Idle Static & Rotary Mechanical Equipments Fire Protection System for Electrical Installations
FIRE AND SAFETY SL. CODE / NO. STANDARDS 161 OISD-STD-174 162 OISD-STD-175 163
OISD-STD-176
164 165
OISD-STD-177 OISD-GDN-178
166
OISD-STD-179
167 168
OISD-GDN-180 OISD-STD-181
169
OISD-GDN-182
170
OISD-STD-183
171
OISD-STD-184
172 173 174 175
OISD-GDN-185 OISD-STD-186 OISD-STD-187 OISD-STD-188
176
OISD-STD-189
DESCRIPTION Well Control Cementing Operations Safety Health & Environment Training For Exploration & Production (Upstream) Personnel Inspection & Maintenance of Thermal Insulation Guidelines on Management Of Change Safety Requirements On Compression, Storage, Handling & Refueling Of Natural Gas For Use In Automotive Sector. Lightning Protection Geophysical Operations Recommended Safe Procedures & Guidelines For Work over and Well Stimulation Operations Standard on Logging Operations Standard On Replacement Of Personal Protective Equipment and Life Saving Appliances Wire Line Operations Combined Operations Care And Use Of Wire Rope Corrosion Monitoring Of Offshore & Onshore Pipelines Standard On Fire Fighting Equipment For Drilling Rigs, Work Over Rigs And Production Installations
177 178 179 180 181
OISD-STD-190 OISD-STD-191 OISD-GDN-192 OISD-GDN-193 OISD-STD-194
182
OISD-STD-195
183
OISD-GDN-196
184
OISD-GDN-197
185
OISD-GDN-199
186
OISD-GDN-200
Derrick Floor Operations (Onshore Drilling / Work over Rigs) Oil Field Explosive Safety Safety Practices During Construction Guidelines for Gas Lift Operations and Maintenance Standard for Storage And Handling Of Liquefied Natural Gas (LNG) Safety in Design, Operation, Inspection and Maintenance of Hydrocarbon Gas Compressor Stations and Terminals Guidelines for Seeking Environmental Clearance of Development Projects in Petroleum Industry Guidelines for Environmental Impact Assessment Guidelines For Conducting Environmental Audit In Upstream Petroleum Sector (Onland) Guidelines For Preparation Of Oil Spill Response Contingency Plan
FIRE AND SAFETY SL. NO. CODE / STANDARDS 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201
DESCRIPTION
Recommended Practices for Environment Protection in Upstream Petroleum Sector (Onland Facilities) OISD-GDN-202 Inspection of Drilling and Work over Rig Mast / Sub-Structure OISD-GDN-203 Operation, Maintenance & Inspection Of Hoisting Equipment Medical Requirements, Emergency Evacuation And Facilities (For OISD-GDN-204 Upstream) OISD-RP-205 Crane Operation, Maintenance and Testing (For upstream) OISD-GDN-206 Guidelines on Safety Management System in Petroleum Industry OISD-GDN-207 Contractor Safety OISD-STD-210 Storage, Handling and Refueling of LPG for automotive use OISD-GDN-211 Safety in Petroleum Laboratories OISD-GDN-212 Guidelines on Environmental Audit in Downstream Petroleum Sector OISD-GDN-217 Formulation Of Environment - Management Plan For Drilling Operations Guidelines For Safe Rig- Up And Rig- Down Of Drilling And Work-Over OISD-GDN-218 Rigs Guidelines on Field Inspection, Handling and Testing of Casing Pipe & OISD-GDN-219 Tubing OSHA (Occupational Safety and Health Administration, USA) Process Safety Management standard CFR 1910.119 Andhra Pradesh Factories Rules, 1950 OISD-RP-201
202 203 204 205 206
Chemical Accident (Emergency Planning, Preparedness and Response) Rules, 1996 The Petroleum Rules, 2002 and amendments HPCL-VR Safety Regulations for contractors, October 2004 HPCL-VR International Safety Rating System requirement MINAS (Minimum National Effluent Standards)
ENVIRONMENT
Sl No 1
Description Of the Act Water (Prevention & Control of Pollution) Act 1974, Act 1977 and the rules & order made there under.
2 Air (Prevention & Control of Pollution) Act 1981 and the rules & order made there under. 3 The Environment (Protection) Act 1986 and rules there under. The manufacture, storage & import of hazardous chemical Rules 1989 with amendment in 4 1994 & 2000. The hazardous wastes (Management & Handling) Rules 1989 with amendment in 2000 & 5 2003. 6 The Noise Pollution (Regulation & control) Rules 2000. 7 The Batteries (Management & Handling) Rules 2001. 8 Ozone Depleting Substance Rules. 9 Environment Impact Assessment 1994. 10 The Public Liability Insurance Act 1991 & Rules. 11 EPA (Environmental Protection Agency, USA) Risk Management Program 40 CFR 68 HPCL-VR ISO 14001 Environmental Management System legal responsibility matrix 12 manual MRO/EPM/PR/202
LAB CODES AND STANDARDS MASTER LIST OF TEST METHODS
Sl. No.
CODES / STANDARDS
EQUIVALENT CODES / STANDARDS
DESCRIPTION
1 APHA 2540–D
20th Edition:TSS Total suspended solids dried at 103-105ºC
2 APHA 4500 S2–F
20th Edition:Sulphides by Iodometric
3 APHA 4500
20th Edition: pH, Electrometric method
4 APHA 5210–B
20th Edition: Three day BOD Test (As per amendment 1 of the environmental (protect)
5 APHA 5220–B
20th Edition: Chemical oxygen demand by Open reflux
6 APHA 5520–B,C
20th Edition: Oil & Grease Partition Gravimetric method
7 APHA 5530–D 8 ASTM D 2274
-
9 ASTM D 2420
-
10 ASTM D 3120
-
20th Edition: Phenols Oxidation stability of distillate fuel oil (Accelerated Method) Hydrogen Sulphide in Liquefied Petroleum (LPGases) (Lead Acetate Method) Trace Quantities of Sulphur in light liquid petroleum hydrocarbons by Oxidative Micro Coulometry
11 ASTM D 3246
-
12 ASTM D 3605
-
13 ASTM D 4052
-
14 ASTM D 4294
Sulphur in petroleum Gas by Oxidative Micro Coulometry Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy Density and Relative Density of Liquids by Digital Density Meter Sulphur in Petroleum and Petroleum Products by Energy Dispersive X-Ray Fluorescence Spectrometry
IP 336
15 ASTM D 4737
-
Calculated Cetane Index by Four Variable Equation
16 ASTM D 4740
-
Cleanliness and Compatibility of Residual Fuels by Spot Test
17 ASTM D 4929
-
18 ASTM D 4951
-
19 ASTM D 5001
-
20 ASTM D 5002
-
Determination of Organic Chloride Content in Crude Oil Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry Measurement of Lubricity of Aviation Turbine Fuels by the Ballon-Cylinder Lubricity Evaluator (BOCLE) Density and relative density of crude oil by digital density meter
LAB CODES AND STANDARDS MASTER LIST OF TEST METHODS
Sl. No.
CODES / STANDARDS
EQUIVALENT CODES / STANDARDS
DESCRIPTION
21 ASTM D 5185
-
Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
22 ASTM D 5443
-
Paraffin, Naphthene, an d Aromatic Hydrocarbon Type Analysis in Petroleum Distillates Through 200 0C by Multi Dimensional Gas Chromatography
23 ASTM D 5580
-
Determination of Benzene, Toluene, Ethylbenzene, p/mXylene, o-Xylene,C9 and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography
24 ASTM D5708
-
Determination of Nickel, Vanadium & Iron in Crude oils and residual fuels by ICP/AES
Color of Petroleum Products by the Automatic Tristimulus Method Oxygenates and Paraffin, Olefin, Naphthene, Aromatic (OPONA) Hydrocarbon Types in Low-Olefin Spark Ignition Engine Fuels by Gas Chromatography
25 ASTM D 6045
-
26 ASTM D 6293
-
27 IP 227
-
Determination of Corrosiveness to silver of Aviation turbine fuels - Silver strip method
28 IP 352
-
Determination of the Lead content of Automotive Gasoline – Energy Dispersive X-Ray Fluorescence Spectrometry method.
29 IP 432
-
Liquefied Petroleum gases – Calculation method for Density and vapour pressure Determination of Water - Coulometric Karl fisher Titration method. Determination of contamination in Middle distillates
30 IP 438
ISO 12937
31 IP 440
EN 12662
32 IP 450
ISO 12156
Diesel fuel – Assessment of Lubricity using the high frequency reciprocating Rig. (HFRR)
33 IS 1202 34 IS 1203
-
1st revision: Determination of Sp.Gravity 1st revision: Determination of Penetration
LAB CODES AND STANDARDS MASTER LIST OF TEST METHODS
Sl. No.
CODES / STANDARDS
EQUIVALENT CODES / STANDARDS
DESCRIPTION
35 IS 1205
-
1st revision: Determination of softening point
36 IS 1208
-
1st revision: Determination of Ductility
37 IS 1211
-
1st revision: Determination of water content (Dean and Stark Method)
38 IS 1212
-
1st revision: Determination of loss on heating
39 IS 1216
-
1st revision: Determination of Solubility in carbon disulphide, carbon tetrachloride or trichloroethylene
IP 1 & 182 ASTM D 611 ASTM D 482
1st revision: Flash and fire point by Cleveland (open) Cup 1st revision,P2: Acidity 2nd revision,P3: Aniline Point 2nd revision,P4: Ash, Sulphated Ash& Water Soluble Ash
ASTM D 187 1st revision,P5: Burning Quality P7: Calorific value by calculation ASTM D 524 1st revision,P8: Carbon residue by Ramsbottom Method ASTM D 97 1st revision, P10: Cloud point and pour point ASTM D 2386 / 3rd revision,P11: Freezing point of aviation fuels 5901 ASTM D 1500 1st revision,P12: Color by ASTM color Scale ASTM D 156 P14: Color by Say bolt Chromo meter ASTM D 130 / D 2nd revision,P15: Detection of Copper Corrosion of 1838 petroleum products By the copper strip tarnish test 3rd revision,P16: Density of crude petroleum and liquid ASTM D 1298 petroleum products by hydrometer method ASTM D 86 2nd revision,P18: Distillation IP 30 1st revision,P19: Doctor Test 2nd revision, P20: Determination of Flash point by Abel IP 70 Apparatus 2nd revision, P21: Flash point (closed) by Pensky Martens ASTM D 93 Apparatus 2nd revision,P22: Asphaltenes precipitation with Normal ASTM D 6560 Heptane
LAB CODES AND STANDARDS MASTER LIST OF TEST METHODS
Sl. No.
CODES / STANDARDS
EQUIVALENT CODES / STANDARDS
ASTM D 1319 ASTM D 445 ASTM D 2700 ASTM D 2699 ASTM D 525
DESCRIPTION
3rd revision,P23: Hydrocarbon types in liquid petroleum products by Fluorescent Indicator adsorption Method 1st revision, P25: Determination of kinematic and dynamic viscosity. P26: Knock characteristics of Motor fuels by the Motor method P27: Knock characteristics of Motor fuels by the Research method 3rd revision,P28: Oxidation stability of Motor Gasoline and Aviation Fuels
ASTM D 381
2nd revision,P29:Existent Gums in fuels by Jet Evaporation
ASTM D 473
1st revision,P30: Sediment in crude and fuel oils by extraction
ASTM D 1322 ASTM D 323
1st revision,P31: Smoke point P36: Sulphur Mercaptans 1st revision,P39: Vapor Pressure by Reid method
ASTM D 95
3rd revision,P40: Water by distillation
ASTM D 4007
3rd revision,P41: Water and sediment in crude oils and fuel oils by centrifuge
ASTM D 1094 ASTM D 1159 ASTM D 3241 ASTM D 3237 IP 309 ASTM D 2163
2nd revision,P42: Water reaction of Aviation fuels 2nd revision,P44: Bromine number by electrometric titration method 1st revision,P64: Non Volatile matter in Solvents P97: Thermal oxidation stability of aviation turbine fuels (JFTOT Method) P109: Determination of Mercaptan Sulphur – amprometric and potentiometric method for Aviation turbine fuels P110: Cold filter Plugging point Of Distillate fuels P111: Analysis of Liquefied petroleum gases and propylene concentrate by Gas Chromatography
LAB CODES AND STANDARDS MASTER LIST OF TEST METHODS
Sl. No.
CODES / STANDARDS
EQUIVALENT CODES / STANDARDS
ASTM D 3242 ASTM D 1840 ASTM D 3948 ASTM D 873 ASTM D 2624 41 IS 1758
-
DESCRIPTION
P113: Determination of total acidity of ATF P118: Naphthalene’s Hydrocarbon in ATF By UV Spectrophotometry P142: Determination of water separation characteristics of aviation turbine fuels by portable separometer P147: Determination of Potential gum in motor gasoline P 148: Determination of Electrical conductivity of aviation and distillate fuels containing static dissipater additive Appendix A: Emulsification test
42 43 44 45
IS 4576 IS 9381 IS 9382 IS 10512
-
Table-1,Note-5:Odor of Liquefied Petroleum Gases Determination of Frass breaking point of bitumen Determination of Effect of heat and air by thin film oven test Determination of wax content in Bitumen