PWR TX Power Level (Manpack) VAU Power Level (Vehicle) Scroll to desired power NAME Change Name (Input NET Name)
SQ Digital Squelch (ON)
Press to exit programming and return to the main preset
PWR SET SINCGARS TIME MANUALLY
Scroll
to desired power
Change Name (Input NET Name)
to desired power
Press to exit programming and return to PRESET
Scroll
to desired power
NAME
NAME Change Name (Input NET Name)
TX Power Level (Manpack) VAU Power Level (Vehicle)
Change Name (Input NET Name)
Press to exit programming and return to the PRESET Press to exit programming and return to the PRESET
to SINCGARS NET, Press OPT #7 TIME GTOD Input Date and Time CLR 2 times to return to PRESET HOPSET COPY Press PGM (8), NORM GENREAL HOPPING HOPPING TYPE (SINCGARS) HOPSET COPY, COPY FROM 20-24, COPY TO 01-25, Input HOPSET ID (FXXX), ENT
SATCOM 25K DAMA Press PGM (#8) button DAMA PRESETS NETS Net to Modif y (0-9)
CHANNEL Channel Number (XXX) FROM SAA Transmit Capability (FULL) Constant Key Port (NO) Def ault Conf ig (0)
RANGING Ranging Method (ACTIVE) ADDR Base Address (One per Radio) Input Base Address (XXXXX) Guard List ADD Input Guard Address (XXXXX) FROM SAA CLR 2 times TRANSEC OW Encry ption (ON) Key Location 0-7 = (TSK01) POWER TX Power VAU Power Lev el Scroll
to desired power
NAM E Input NET Name CLR 1 Time PORT CONFIG 0 (DAMACFG0) COMSEC Cry pto Mode (ANDVT) Encry ption KEY (TEK 01) Training Frames (20) Voice Autoswitch (DISABLED) DATA /VOC Voice Mode (MELP) SY NC / ASY NC (SYNC) Baud Rate (2400) DASA Option Code (010) CONFIG CODE 25KHz (XX) FROM SAA 5KHZ (XX) FROM SAA NAM E Input Config Name CLR 1 Time DESTINATION 00 (DAMADEST0) 25K_AC ADD Destination to ADD (XXXXX) CLR 1 TIme NAM E Input Destination Name
Press CLR 5 times to return to PRESET
Loading TEK/KEK/TSK from an SKL to AN/PRC-117F
Loading SINCGARS FH DATA from an SKL to AN/PRC-117F
PREPARE RADIO TO RECEIVE COMSEC KEYS
PREPARE RADIO TO RECEIVE SINCGARS LOADSET
1. Rotate C ipher Switch to LD 2. FILL DEVICE (KYK-13) 3. C RYPTO TYPE (VINSON) 4. KEY TYPE (TEK) 5. KEY NUM: (01) 6. Press ENTER to INTITATE! STOP!!!! PREPARE SKL TO TRANSER COMSEC KEYS
1. Rotate C ipher Switch to LD 2. C onnect Fill cable to SKL & Radio. 3. FILL DEVICE (CYZ-10 RDS) 4. Press ENT to Intitate Fill 5. FILL IN PROGRESS STOP!!!! PREPARE SKL TO TRANSER SINCGARS LOADSET 1 . Selec t the PLA TS tab 2 . H ighlight the desired SINCGA RS PLA TFORM
1.Selec t the KEYS tab
2 . H ighlight the key that you want to load.
3 . Selec t the LOAD ic on the tool bar.
from
4 . Set the Protocol and A ctivate Modes to DS-102
5 . Selec t OK 6 . When you get this prompt
3 . Selec t the LOA D ICON from the tool bar. 4 . Set the SI N CGARS Mode T ransfer T ype to ICOM TRA NSFER. I f time is des ired s elec t INCLUDE TIME (time not required)
5 . Selec t NEXT 6 . Selec t SEND 7 . When this s c reen appears
P res s ENT button on the radio P res s the ENT button on the radio
COMPLETE FILL at RADIO 1. Press ENT to Initiate Fill 2. Fill Done, Press any Key 3. More Fill Data (Y/N)
8 . A t this s creen s elect NO ! 9 . O peration is s uccessful when this s c reen appears
COMPLETE FILL at RADIO 1. Key Store in Progress 2. Fill Done, Press any Key 3. More Fill Data, (Y/N)
