PRACTICAL PROBLEMS
1. A 1/8 bend fittings is equivalent to? a.
22 ½ degrees fittings b. 30 degrees degrees fittings c. 45 degrees fittings d. 90 degrees fittings
2. A 1/16 bend fittings is equivalent to? a. 22 ½ degrees fittings b. 30 degrees fittings c. 45 degrees fittings d. 90 degrees fittings fittings 3. When cutting pipe that coated internally with enamel or glass, delicate core should be taken to avoid cracking or chipping the internal coating. What kind of tool that should neve r be used for cutting such pipe? a. Adjustable Hacksaw c. Wheel pipe cutter b. Pipe reamer d. Square-edge pipe cutter 4. What is that tool used for expanding the ends of lea d pipe? a. Shave hook c. Drift plug b. Turn pin
d. Dresser
5. What is that valve recommended for installations that call for throttling? a. Globe valve
c. Check valve
b. Gate valve
d. Angle valve
6. What is the minimum length of time before a jointed plastic pipe be subjected to pressure test? a. 1.5 hours
c. 2.5 hours
b. 2 hours
d. 3 hours
7. What will be the maximum water service pressure at the point where the building distribution system begins? a. 80 psi
c. 100 psi
b. 90 psi
d. 120 psi
8. What is the minimum size of a septic tank manhole? a.
602mm x 602mm b. 508mm x 508mm c. 550mm 550mm x 550mm d. None None of the above above
9. Is the Revised Plumbing Code of the the Philippines allows Wooden type of Septic tank? a.
Yes b. No c. No mention d. None None of the above
10. What device to be installed for for commercial or Industrial Special waste when liquid wastes containing excessive amounts of grease,garbage, flammable wastes, sand, or other ingredients which may affect the operation of a private sewag e disposal system.
a.
Receptor b. Interceptor c. Septic Tank d. None of the above
11. What test shall be applied to any drainage and vent system? a.
Air test b. Water Test c. Vacuum Test d. None of the above
12. . What test shall be applied to water distribution system? a.
Air test b. Water Test c. Vacuum Test d. None of the above
13, In how many minutes shall a water or air be on piping system before inspection for both water test and air test for any plumbing system? a.
10 minutes b. 15 minutes c. 20 minutes d. None of the above
14. When a water pipe crosses a sewer or drainage piping constructed on a clay materials, where shall our water pipe be located? a. 0.30m below a sewer or drainage pipe c. 0.30m above a sewer or drainage pipe b. 0.30m parallel to the sewer or drainage pipe d. None of the above 15. All indirect waste from food equipments must be separated by ______when discharging it to drainage system? a.
air break b. air gap c. full air break d. full air gap
16. All indirect waste from sterile equipments shall be drained through an________. a.
air break b. air gap c. full air break d. full air gap
17. An adjustable plumbing tool for gripping hexagonal nuts, with an adjusting screw in the head of the implement. a. Pipe Wrench b. Monkey Wrench
c. Sink Wrench
d. None of the above
18. A plumbing tool used to tighten connections in deeply recessed places that are very hard to get at normally. a. Pipe Wrench b. Monkey Wrench c. Sink Wrench d. None of the above 19. An approved tank or pit that collects sewage or liquid waste and which is located below the normal grade of the gravity plumbing system and that requires mechanical means to be emptied is called a: a. Cesspool b. sewage c. sump 20. A lined excavation in the ground that receives the discharge of a drainage of a drainage system that has been designed to retain organic matter and solids while allowing liquids to seep through the bottom and sides is known as: a. Leech field
b. septic tank
21. On what type of building are we t standpipes generally used?
c. Cesspool
a. Tall building
c. Very tall building b. Large building d. Smaller building
22. Fire system piping is usually painted with? a. Red color b. Yellow color
c. Green color d. Blue color
23. Clevis hangers are used for: a. b. c. d.
Vertical installation only Horizontal installation only Vertical and horizontal installation None of the above
24. Flux is applied to copper pipe and fittings a. b. c. d.
after cleaning pipe ends and fittings before assembling pipe and fittings before applying heat All of the above.
25. Zero gauge pressure is also known as atmospheric pressure and is a.
14.7 psi b. 29 inch mercury c. both a & b d. None of the above
26. The recovery rate of water heater is also reffered to us: a.
gpm b. gph
c. gpd d. None of the above
27. A solar water heater panel is also known as a: a. roof heater b. circulator c. collector d. pump collector 28. Regardless of the type of heater all energy source must be turn off before attempting to; a. drain a water heater b. check the temperature of the water c. do pressure check of the water system d. None of the above e. 29. A device with at least a 75 0 gallon capacity that is meant to serve one or more fixtures in preventing grease from entering the building drain and which is remotely located is called a: a. Grease trap
b. Grease Interceptor
30. A house sewer is: a. located outside the house c. inside the house b. both a & b d. None of the above
c. Grease diverter
31. How many BTU per hour in One hp? a.
2545
b. 2455
c. 2554
d. None of the above
32. How many gallons in one cubic ft? a.
7.84 b. 7.48 c. 7.83 d. 7.47
33. Sizing of gas system begins with: a. b. c. d.
the first piece of pipe from delivery point the farthest appliance from the delivery point the middle of the system none of the above
34. The use of a circuit vent and a loop vent eliminates the need for: a. a vent stack c. a stack vent b. p-traps d. multiple individual vents 35. The base of a waste stack connects with the: a. stack vent c. building sewer b. building drain d. none of the above 36. A hanger used to support a vertical pipe that penetrates a floor is called a: a. b. c. d.
vertical pipe supporter riser clamp clevis hanger split ring hanger
37. A clevis hanger uses threaded rod along with: a. wood screws c. hex nuts and possibly washer b. anchor bolts d. a threaded thimble 38. The most common distance between the hot and cold roughing in on a sink is: a.
4” b. 6” c. 8 “ d. 3”
39. To minimize water hammer: a. a quick closing valve is installed c. a shock absorber is installed b. all water hammer arrestors are removed d. None of the above 40. To minimize water retention in Whirlpool bathtubs pump and circulating piping must be: a.
have a p-trap b. self draining
c. both a & b
d. None of the above
41. What is the minimum number of pump required in in a sump pit? a.
1 b. 2 c. 3 d. None of the above
42. What is the minimum clearance from invert elevation of inlet pipe to a sump pit from the starting level of pumping operation of sump pit? a.
4” b. 6” c. 2” d. None of the above
43. For the hot and cold water distribution system, on what side should the hot water supply be placed in combination fittings? a.center
b.right c.left d.none of these
44. What is the shape for the signage for women's comfort room in order to aid visually impaired women readilty determine whether a washroom is for men or women? a.TRIANGLE b.RECTANGLE
c.CIRCLE d.SQUARE
45. Drainage piping serving fixtures located below the crown l evel of the main sewer shall discharge into an approved water tight A.cesspool B.septic tank
C.leaching tank D.sump
46. In the water test of the entire plumbing system all openings should be tightly closed except at A.producing cleanouts B.highest opening C.stack vent D.bleeders 47. Where practical, all pipes from fixtures shall be run in what direction with respect to the nearest wall or building line? A.perpendicular B.across C.offset D.parallel 48. What is the type of Siamese connection that all 125-millimeter dry standpipes shall be equipped with? A.two-way B.three-way C.four-way D.one-way 49. What installation standard is followed in joining plastic pipe and fittings by solvent cement? A.ANSI B.ASHRAE C.IAPMO D.ISO 50. Which of the following is the primary basics for sizing vertical rainwater piping in the Revised National Plumbing Code? A.roof area B.wind direction C.slope of roof D.intensity of rainfall 51. Which copper piping is mainly used in commercial work?
A.Type C B.Type K C.Type L D.Type M E.None of the above 52. Soldering copper joints is commonly known as what? A.Silvering
B.Sweating C.Threading D.Welding
53. How far must the pipe must go into the fitting socket in order to ensure that the joint holds? A.At least 1/4" B.Half the diameter of the tubing C.All the way until it "bottoms out" inside the fitting D. None of the above 54.How do you know when the copper fitting and tubing are hot enough to apply solder? A.The solder melts when it touches the joint B.The copper glows bright red C.The flux bubbles and hisses D.You can no longer hold the pipe with your hand 55. Stem packing is used when leaking occurs at which location? A.Tub Spout B.Shower valve C.Drain D.Shower Head 56. Where is the cold water valve located? A.Left Side B.Right Side C.Center D.Bottom 57. How many p-traps does a double kitchen sink require? A.One B.Two C.Three D.Four 58. What fits between a closet flange and toilet bowl? A.Spud washer B.Wax Ring C.O-Ring D.Lock Washer 59. What color of flame is best for solderi ng? A.Red B.Yellow
C.Blue D.Orange 60. What substance is not permitted in solder which is used for water supply pipes? A.Tin B.Brass C.Lead D.Steel 61. If a Plumbing Plan scaled as 1: 200 , then s 1 cm in the plan is equal to____ in actual ? A.200 ft
B.200 mts C.2 mts D.2ft.
62. If a Plumbing Plan scaled as 1: 1, 000 , then 2 cm in the plan is equal to____ in actual ? A.200 ft B.200 mts C. 2 mts D.2ft. 63. If a Plumbing Plan scaled as 1: 50 , then 400 square cm in the plan is equal to____ in actual ? A.100 sq. ft . B.100 sq mts C. 200 sq. mts D.200 sq. ft. 64. . If a Plumbing Plan scaled as 1: 50 , then 20 cm x 40cm cistern plan is equal to____ cubic mts in actual ? Assume 2.00 mts actual depth of the cistern. A.800 cu mts B. 1600 sq. mts C. 400 cu mts D.2400 cu mts 65. . If a Plumbing Plan scaled as 1: 10,000 , then 10 cm x 20cm catchment area in the plan is equal to____ cubic mts of rainfall in actual for every hour ? Assume 100 mm/hr rain intensity. A.300,000 cu mts B. 200,000 cu mts C. 400,000 cu mts D.None of the above 66. According to BP 344 Accessible toilet compartments shall have the following a minimum area of ____. a.
1.60 m x 1.80 m. b. 1.50 m x 1.80 m. c. 1.80 m x 1.80 m. d. 1.70 m x 1.80 m.
67. . According to BP 344 A turning space of ____ sq. m with a minimum dimension of _____mm for wheelchair users shall be provided outside water closet cubicles. a.
2.15 , 1500
b. 2.25 , 1800 c. 2.25 , 1500
d. 2.30 , 1800
68. According to BP 344 a minimum of one accessible to persons with disabilities water closet in every floor for every ____ regular water closet. a.
20 b. 25 c. 15 d. None of the above
69. According to BP 344 the maximum height of toilet seat for persons with disabilities is _______? a.
450 mm b. 500 mm c. 400 mm d. None of the above
70. According to BP 344 the maximum height of lavatory for persons with disabilities is _______with knee recess of 0.60m-0.70m depth of 0.50m?
a.
700 mm b. 800 mm c. 600 mm d. None of the above
Match each tool with its corresponding description. a) Adjustable open-end wrench b) Basin wrench c) O-rings and rubber seats d) Pipe wrench e) Plumber's pliers f) Rubber washers 71. The tool’s jaws can expand wide enough to get around pipes of all sizes, e xposing serrated teeth that provide great grip 72. Mostly used as a specialty tool for steel pipes, but also good in a pinch for getting to some difficult nuts 73. Its smooth jaws are made to fit small nuts, bolts, and square and hexagonal fittings 74. Used as gaskets for washer less faucets 75. Its long handle with spring tension pipe-gripping jaws allows you to reach up to grip pipe nipples or tighten/loosen nuts in tight, hard-to-reach areas. 76. Used as gaskets for compression faucets 7 1e; 72d; 73a;7 4c; 75b;76f
a. Vent b. Drain Above Ground c. Hot Water d. Cold e. Elbow turn down f. Elbow turn up g. Elbow 45
Water degrees
86. Identify this valve a.
Gate valve b. PRV c. Globe Valve d. None of the above
87. . Identify this valve a.
Gate valve b. PRV c. Globe
Valve d. Check Valve
88. ______ is the difference, measured in feet, between the static water level and the pumping level. a. Total Dynamic Head b. Static Head c. Drawdown d. NPSH 89. ________ is the result of vapor bubbles imploding. This occurs when the amount of water flowing into the pump is restricted or blocked. a.
Water Hammer b.Siphonage c. Cavitation d. None of the above
90. Net Positive Suction Head Available must always be lesser than Net Positive Suction Head Required by pump to avoid air related problems of pump impeller. a.
False b. True c. None of the Above
91. ________ plumber- has served his apprenticeship and is competent to perform the tasks of installing and repairing plumbing. a.
Journeyman b. Apprentice c. Master d. None of the above
92. ___________- water drained from lavatories, sink, laundry trays and showers; contains minor pollutants. a.
Black Water b. Gray Water c. Potable water d. None of the above
a. f.
Pendant b.Upright c. Vertical Sidewall d. Recessed Pendant Concealed Horizontal Sidewall e. Concealed Pendant
99. device for regulating the supply of water in a flush tank by means of a hollow floating ball. also called float valve g. A.ball cock B.flushometer valve C.water hammer D.backsplash 100. The pipe from the public water main or source of water supply to the building served A.SERVICE PIPE B.MAIN SERVICE PIPE C.DISTRIBUTION PIPE d. None of the above. h.
