Nikon D2Hs Repair_Manual

VBA10601-R.3665.A 作成承認印

配布許可印サービス

計画課

Ｍ

VBA10601

REPAIR MANUAL

Copyrigh ｃ 2005 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !! Printed in Japan March 2005

VBA10601-R.3665.A

Specifications Type Effective pixels Image sensor Image size (pixels) Lens mount

Single-lens reflex digital camera with interchangeable lenses 4.1 million 23.3 × 15.5 mm; total pixels: 4.26 million 2464 × 1632 (large), 1840 × 1224 (medium) Nikon F mount (with AF coupling and AF contacts)

Type G or D AF Nikkor Micro Nikkor 85 mm

All functions supported All functions supported except autofocus and some exposure modes

F2.8D Other AF Nikkor †

All functions supported except 3D color matrix metering and 3D

AI-P Nikkor

multi-sensor balanced fill-flash for digital SLR All functions supported except 3D color matrix metering, 3D

Non-CPU

multi-sensor balanced fill-flash for digital SLR, and autofocus Can be used in exposure modes A and M; electronic range finder can

Compatible lenses*

be used if maximum aperture is f/5.6 or faster; color matrix metering, multi-sensor balanced fill-flash for digital SLR, and aperture value display supported if user provides lens data IX Nikkor lenses can not be used † Excluding lenses for F3AF Picture angle Equivalent in 35-mm format is approximately 1.5 times lens focal *

Viewfinder Diopter adjustment Eyepoint Focusing screen Fame coverage Magnification Reflex mirror Lens aperture Focus-area selection

length Optical fixed eye-level pentaprism –3 – +1 m–1 19.9 mm (–1.0 m–1) Type B Brite View clear-matte Mark III screen provided Approximately 100% of lens (vertical and horizontal) Approximately 0.86× (50-mm lens at infinity; –1.0 m–1) Quick return Instant return with depth-of-field preview Single area or group can be selected from 11 focus areas

Lens servo

Instant single-servo AF (S); continuous-servo AF (C); manual (M); predictive focus tracking automatically activated according to subject status in single- and continuous-servo AF

- Ｍ1 ･

-

VBA10601-R.3665.A

Autofocus

TTL phase detection by Nikon Multi-CAM2000 autofocus module

Detection range

–1 – +19 EV (0 – +19 EV for focus areas at left and right edges of

(ISO 100 at 20 °C / 68 °F) frame) AF-area mode Single-area AF, dynamic-area AF, group dynamic-AF, dynamic-area Focus lock

AF with closest subject priority Focus can be locked by pressing shutter-release button halfway (single-servo AF) or by pressing AE-L/AF-L button

Exposure Metering Matrix

Three-mode through-the-lens (TTL) exposure metering 3D color matrix metering supported with type G and D lenses; color matrix metering available with other CPU lenses and with non-CPU lenses if user provides lens data

Center-weighted

Weight of 75% given to 6, 8, 10, or 13-mm circle in center of

Spot

frame, or weighting based on average of entire frame Meters 3-mm circle (about 2% of frame) centered on selected

Range

focus area (on center focus area when non-CPU lens is used) 0 – 20 EV (3D color matrix or center-weighted metering)

(ISO 100 equivalent,

2 – 20 EV (spot metering)

f/1.4 lens, 20 °C/68 °F) Exposure meter coupling Exposure control Exposure modes

Combined CPU and AI Programmed auto with flexible program; shutter-priority auto;

Exposure compensation Bracketing

aperture priority auto; manual –5 – +5 EV in increments of 1/3, 1⁄2, or 1 EV Exposure and / or flash bracketing (2–9 exposures in increments

Exposure lock Shutter Speed Sensitivity

of 1/3, 1⁄2, 2/3, or 1 EV) Luminosity locked at detected value with AE-L/AF-L button Electronically-controlled vertical-travel focal-plane shutter 30 – 1/8000 s in steps of 1/3, 1⁄2, or 1 EV, bulb 200 – 1600 in steps of 1/3, 1⁄2, or 1 EV, 3200, 6400; auto gain to 1600

(ISO equivalent) White balance

Auto (TTL white-balance with main image sensor, 1,005 pixels RGB sensor, and ambient light sensor), six manual modes with

Bracketing

fine-tuning, color temperature setting 2–9 exposures in increments of 1, 2, or 3

- Ｍ2 ･

-

VBA10601-R.3665.A

Flash

Sync contact

X-contact only; flash synchronization at up to 1⁄250 s

TTL

TTL flash control by combined five-segment TTL multi sensor with

Flash contrrol

single-component IC and 1,005-pixel AE sensor • SB-800, 600: i-TTL balanced fill-flash for digital SLR and standard i-TTL flash for digital SLR • SB-80DX, 28DX, or 50DX with type G or D lens: 3D multi-sensor balanced-fill flash for digital SLR • SB-80DX, 28DX, or 50DX with other lens: multi-sensor balancedfill flash for digital SLR • SB-80DX, 28DX, or 50DX with spot metering: standard TTL flash Auto aperture Non-TTL auto Range-priority manual Sync modes

for digital SLR Available with SB-800, 80DX, or 28DX and CPU lens Available with such Speedlights as SB-800, 28, 27, and 22s Available with SB-800 Front curtain sync (normal), slow sync, rear-curtain sync, redeye

Flash-ready indicator

reduction, red-eye reduction with slow sync Lights when SB-series Speedlight such as 800, 600, 80DX, 28DX, 50DX, 28, 27, or 22s is fully charged; blinks for 3 s

Accessory shoe Creative Lighting

after flash is fired at full output Standard ISO hot-shoe contact with safety lock With SB-800 and 600, supports Advanced Wireless Lighting

System

(SB-600 only supports AWL when used as remote flash), Auto FP High-Speed Sync, Flash Color Information Communication,

Storage

modeling illumination, and FV Lock

Media File system

Type I and II CompactFlash memory cards; Microdrives Compliant with Design Rule for Camera File System (DCF) and

Compression

Digital Print Order Format (DPOF) • Compressed 12-bit NEF (RAW): approximately 50–60% • JPEG: JPEG baseline-compliant, can be selected from Fixed size

Self-timer Depth-of-field preview

and Optimal quality Electronically controlled timer with 2 – 20s duration Lens aperture stopped down when depth-of-fi eld preview button is

Monitor

pressed 2.5″ , 232,000-dot, low-temperature polysilicon TFT LCD with brightness adjustment

- Ｍ3 ･

-

VBA10601-R.3665.A

Video output External interface Tripod socket Firmware Supported languages

Can be selected from NTSC and PAL USB 2.0 1⁄4″ (ISO) User upgradeable Chinese (Simplified), Dutch, English, French, German, Italian,

Power source

Japanese, Korean, Spanish, Swedish • One 11.1V EN-EL4 rechargeable Li-ion battery

• EH-6 AC adapter (available separately) Dimensions (W × H × D) Approximately 157.5 × 149.5 × 85.5 mm (6.2″ × 5.9″ × 3.4″ ) Weight

Approximately 1070 g (2 lb 6 oz) without battery, memory card, body cap, or monitor cover

Operating environment Temperature Humidity

0 – 40 °C (32 – 104 °F) Less than 85% (no condensation)

• Unless otherwise stated, all figures are for a camera with a fully-charged battery operating at an ambient temperature of 20 °C (68 °F). • Nikon reserves the right to change the specifications of the hardware and software described in this manual at any time and without prior notice. Nikon will not be held liable for damages that may result from any mistakes that this manual may contain.

- Ｍ4 ･

-

VBA10601-R.3665.A

Precautions for disassembly/(re)assembly

Notes： ①　In disassembly/(re)assembly, be sure to use conductive mat (J5033) and wrist strap (J5033-5), in order to protect electric parts from static electricity. ②　Before disassmbling, be sure to remove batteries, AC power cord, and battery for clock (CR1616). 　　　

③　In disassembling, be sure to memorize the processing state of wires and FPC, screws to be fixed and their types, etc. ④　The low-pass filter of the image PCB is easily damaged. Handle it very carefully. ⑤　In the chapter of Disassembly, sometimes a large assembly unit is removed. In case such a unit is further disassembled , refer to the exploded technical drawings.

　　 ⑥　In Disassembly/(re)assembly chapters, the dip-proof sponge is not mentined. In case parts are replaced, be sure to attach the dip-proof sponge by referring to the exploded technical drawings. ⑦　All wires are special parts (supporting UL), so be sure to use specified wires.

　Points to notice for Lead-free solder products 　・Lead-free solder is used for this product. 　・For soldering work, the special solder and soldering iron are required. 　・Do NOT mix up lead-free solder with traditional solder. 　・Use the special soldering iron respectively for lead-free solder and lead solder. They cannot be used in common.

Disassembly

1. External units and Imaging-related PCBs Note 1: Before disassembling a camera, of which the main FPC should be replaced, be sure to read and note down the adjustment value of the environment light sensor by adjustment software for the camera unit. If the value cannot be read out from the camera, replace the top cover unit, too. (Refer to Page A28 for the details when replaced.) Note 2: When "Seprating Front and Rear bodies", "Disassembling Image PCB", and "Disassembling Bayonet", be sure to perform "Reset of AF defocus compensation amount" by D2Hs adjustment software after reassembly.

External rubber ・Remove the grip rubber (#B60-1), apron lower rubber (#B66), and rubber at the film rewind side (#B61).

#B61

#B66 #729 #B60-1

- Ｄ1 ･

-

VBA10601-R.3665.A

I/F Block ・Take out 3 screws (#1589) and detach the I/F block.

#1589×3

I/F Block

Grip Cover ・Take out 2 screws (#1534) and 2 screws (#1510) to detach the grip cover.

#1534×2

#1510×2

Grip cover

- Ｄ2 ･

-

VBA10601-R.3665.A Bottom Cover Unit 1. Remove Vertically position FPC

　・Remove the vertically position FPC from the connector.

Vertically position FPC

2. Remove Bottom cover unit

　・Take out 3 screws (#1512) and 3 screws (#1517). 　・Remove the bottom cover unit from the camera body.

Note: Between the bottom cover and the body (i.e. A part), there is the washer (T=0.3) inserted. When assembling, be sure to put it back into the original position. (This measure is for filling in a gap between the back door and bottom cover.)

A part #1512×3

Bottom cover unit

#1517×3

- Ｄ3 ･

-

VBA10601-R.3665.A

Back door unit 1. Remove Back door unit 　・Take out 4 screws (#1514) and detach the back door unit slowly. 　・Remove the TFT (Memory compression PCB connection-FPC: #5041) from the connector. (ref. Fig.1）

#1514×4

Back door unit

Connector

Fig.1

#5041

2. Remove TFT Monitor 　・Remove the red and black wires of the TFT back light harness. 　・Remove the TFT monitor FPC and AF area FPC from the connector.

AF area FPC

TFT monitor FPC

Red: TFT back light Black: TFT back light

　・Take out 2 screws (#436) and remove the TFT retaining (#432) and TFT monitor (#5043).

#432 #5043 #436×2

- Ｄ4 ･

-

VBA10601-R.3665.A

3. TFT-PCB, Speaker, Microphone, other small parts

#425

#453

#445 #427 �

#1513×2 #B428

�

TFT PCB

#1522×2

#463 Speaker #437

#1560×2 #460 #467 #442 Microphone #B439

#456

#1508×3

#1531×2

TFT & Memory compression PCB connection-FPC 　・Remove the TFT & Memory compression PCB connection-FPC (#5041) from the connector. #5041

Connector

- Ｄ5 ･

-

VBA10601-R.3665.A

Battery contacts unit 1. Remove wires 　・Remove the red and black wires that connect from the battery contacts.

Black : Battery contact Red : Battery contact

2. Remove Battery contacts and Battery case upper unit ・Remove the battery contacts connection-FPC from the connector. 　・Take out 2 screws (#1515) and 1 screw (#812) and detach the battery contact unit (#B801). 　・Take out 1 screw (#1520) and remove the battery case upper unit (#B823), (which is attached by the both-sided adhesive tape). #812

#1515×2

Battery contacts connection FPC #B801

#1520

#B823

Connector

- Ｄ6 ･

-

VBA10601-R.3665.A

Imaging (LBCAST) PCB unit 1. Remove Image PCB cover plate

#5040

#592

　・Detach the both ends of the connectionFPC of the memory compression PCB & USB PCB (#5040) from the connector. (The EMI (electromagnetic interference) prevention sheet (#592) is attached on the connection-FPC.）　・Take out 2 screws (#1530). 　・Remove the image PCB cover plate.

2. Remove Image PCB unit 　・Remove the connection-FPC of the image PCB & memory compression PCB (#5038) from the connector. 　・Remove the image PCB harness from the connector. 　・Take out 3 screws (#525). 　・Remove the image PCB unit. 　・Remove the screen frame (#529). Note 1: For some bodies, the washer is already put on the attaching face of the image PCB. There is an indication of the mark in red with magic marker. Refer to Page A25 in the Assembly chapter for the details.

Image PCB cover plate #596

#1530×2

Connector #525×3

Image PCB harness

Image PCB unit

*A part #529 #5038

Connector

*Note 2: For some bodies, there are L-shaped washers attached at 3 parts of A-part on the image-PCB. On such PCB, there is red-marked indication on its attachment side, so if the washers come off, reattach them. In case the PCB is replaced with the one without red marking, the washers are NOT necessary.

- Ｄ7 ･

-

VBA10601-R.3665.A

Top cover unit 1. Remove Top cover FPC connection and EL wires

Top cover FPC

　・Remove the red and black wires on the main PCB. 　・Remove the top cover FPC from the connector.

Red: Back light for top LCD (EL) Black: Back light for top LCD (EL)

2. Remove Top cover unit #1537×2 #B1137 Top cover (#B23)

#1519

#1121 #1130

　・Remove the eyepiece diopter knob cover (#1130). Then take out the screw (#1568) to remove the eyepiece diopter knob (#1121).

#1568 #1510

#1543

　・Take out 8 screws in total (1 screw:#1543, 2 screws:#1537, 1 screw: #1519, 1 screw:#1510, 2 screws:#1516, and 1 screw: #1556). 　・Detach the top cover (#B23) then the eyepiece block unit (#B1171) comes off.

#1516×2 #1556

- Ｄ8 ･

-

VBA10601-R.3665.A

2. Separate Front and Rear bodies Main FPC 1 unit 　・Remove the red and black wires on the main FPC 1 side face. 　・Remove the connection-FPC of the main FPC1 & DC/DC unit 2 (#5033) from the connector. 　・Remove the connection-FPC of the main FPC1 & memory compression PCB (#5035) #1532×2 from the connector. 　・Take out 2 screws (#1532).

Connector Connector

Yellow: Charge motor

#5033

Black: Charge motor

#5035

Main FPC 1 unit

　・Remove the 3 wires (in red, brown and black) that connect from the charge SW. 　・Remove the P - F (Preview & function) FPC (#5027) from the connector. 　・Remove the shutter FPC (#5014) from the connector. 　・Remove the penta FPC (#B15005) from the connector. 　・Unscrew #1553. #5027

#5014

Brown: Charge SW Red: Charge SW Black: Charge SW #B15005 #1553 TA-0005 (6×12)

- Ｄ9 ･

-

#684

VBA10601-R.3665.A #1566×3

　・ Remove the connecting connectors of the main FPC 1 and main FPC 2. 　・Take out 3 screws (#1566) to detach the main FPC 1.

Main FPC 1

Main FPC 2

Back-up Battery Box Unit Red: Back-up battery box Black: Back-up battery box

・Remove the red and black wires on the USB PCB. ・Take out 2 screws (#1533) and remove the back-up battery box unit (#B818).

#1533×2

#B818

- Ｄ10 ･

-

VBA10601-R.3665.A

Separate Front and Rear bodies

Black: I/F PCB 　Orange: I/F PCB

・Remove the black and orange wires that connect from the I/F PCB.

#1590×2

#1535

#1514×6

　・Take out 2 screws (#1590) under the eyepiece. 　・Unscrew #1535. 　・Take out 6 screws (#1514). 　・Separate the front body from the rear body.

- Ｄ11 ･

-

VBA10601-R.3665.A

3. Rear Body I/F PCB unit 1. Remove I/F PCB unit from Rear body

　・Remove the 3 wires (in red, orange and black) from the DC/DC unit 2.

TA-0005 (20×10)×2

　・Remove 2 pieces of the tape TA-0005(20×10). Red: I/F PCB Orange: I/F PCB Black: I/F PCB DC/DC unit 2

I/F PCB unit

　・Take out 2 screws (#1510 and #1523) to remove the I/F PCB unit from the rear body.

#1523×2

#1510

2. Separation into DC-IN video PCB and USB PCB 　・Remove 5 soldering bridges. 　・Take out 3 screws (#1526) to remove the USB PCB from the IF-PCB locking plate. 　・Take out 3 screws (#1526) to the DC-IN video PCB from the IF-PCB locking plate.

Soldering bridge×5

#1526×3

#1526×3

USB PCB

* Fuse-FU1 is replaceable before separating the DC-IN video PCB from the USB-PCB.

*FU1

IF-PCB locking plate

Phenomenon when fuse-FU1 is blown out: In case of using DC-IN as power, the power does NOT turn ON.

- Ｄ12 ･

-

DC-IN video PCB

VBA10601-R.3665.A

CF card PCB unit 1. Remove CF card PCB unit from Rear body #1531×2

・Take out 2 screws (#1531).

#1531×2

　・Take out 2 screws (#1531). 　・Hold down 2 connection-FPCs with fingers so that they are not hooked to the rear body, then remove the CF card PCB unit from the lower holes of the rear body.

CF card eject lever

CF card PCB unit

2 connection-FPCs

- Ｄ13 ･

-

VBA10601-R.3665.A

2. Remove DC/DC PCB unit 1

#1530×2 Black: DC/DC PCB unit 2 Red: DC/DC PCB unit 2

　・Remove the red and black wires. DC/DC PCB unit 1

　・Take out 2 screws (#1530) to remove the DC/DC PCB unit 1.

3. Remove CF Card PCB

#1530×2 CF card PCB

　・Take out 2 screws (#1530). 　・Disconnect the connectors to remove the CF card PCB.

- Ｄ14 ･

Connector

-

VBA10601-R.3665.A

4. Separation of Memory compression PCB and DC/DC PCB unit 2 #1530×3 Memory compression PCB

　・Take out 3 screws (#1530).

Connector ①

　・Disconnect the connectors to separate the memory compression PCB and DC/DC PCB unit 2.

#5035 Connectors Connector ② #5033

DC/DC PCB unit 2

F1

F102 F104

*If the memory compression PCB is separated from DC/DC unit 2, the following fuses (except F104 Polyswitch) can be replaced. ・Phenomenon when fuse or *Polyswitch burns out. F1: Both battery and DC-IN cannot be turned ON. F102: Because there is no power except VBAT and VBT6, the LCD keeps the indications just before burnout of fuses, and also other functions of camera cannot work. *F104: Because there is no output from VCC12 and VCC23, the backlight of TFT cannot light up and TFT shows indications but they can hardly be verified. At the same time, the control panel on top of the camera keeps the indications just before burnout of fuses. As for F104 (Polyswitch), however, if turning the main switch of camera to OFF for a few seconds and then turning to ON, or if removing the battery once and then inserting it again, this Polyswitch recovers its function. So it does not usually burn out (break) permanently, compared with other fuses.

- Ｄ15 ･

-

VBA10601-R.3665.A

5. Remove Locking plate from DC/DC PCB unit 2 #1540 #1530×2 #5086

　・Take out the screws (#1530 and #1540) to remove the locking plate of the DC/DC unit 1 & 2 (#70). 　・Take out 2 screws (#1530) to remove the locking plate of the memory compression PCB & DC/DC PCB unit 2 (#69). 　・Remove the solder of 3 legs of the power transistor (#5086) to detach it.

Locking plate (#70)

DC/DC unit 2

#1530 Locking plate (#69)

6. Remove CF locking plate unit from CF card PCB unit #1530×3 CF card PCB unit

　・Take out 3 screws (#1530) to detach the CF knob cover (#449) and the CF locking plate unit.

#449

CF locking plate unit

- Ｄ16 ･

-

VBA10601-R.3665.A

SQ (Sequence) PCB unit #1538×4

SQ PCB unit

#683

・ Unscrew #683 to remove the shutter FPC from the SQ PCB. Take out 4 screws (#1538). ・・Remove the SQ PCB unit from the rear body.

Shutter FPC

Shutter unit

#1704×3

Shutter unit

　・Take out 3 screws (#1704) to detach the shutter unit. Note）The dust-proof sheet (#540) is attached on the rear body with the both-sided adhesive tape.

#540

- Ｄ17 ･

-

VBA10601-R.3665.A

Rear body small parts

#575 #566 #574 #576

#398

#567

#397

#573

#399

#572

#565

#271

#564 #563 #571

#568

#569 #561

#577-1

#562

#533

#554 #595

- Ｄ18 ･

-

VBA10601-R.3665.A

4. Front Body Adjustable diopter unit

　・Unscrew #1535 to detach the adjustable diopter unit. Adjustable dioptor unit

#1535

Main FPC 2 1. Remove wires, FPCs and soldering bridges ・Remove the red and black wires that connect from the AF motor Red: AF motor Black: AF motor and the black wire that connects Black: Lens contact FPC from the lens contact FPC. ・Remove the grey and black wires #1503 that connect from the lens release SW, and also remove the red, blue and brown wires that connect from SCM change-over.

Lens contact FPC

Red: SCM change-over Blue:　〃　〃 Brown:　〃　〃 Gray: Lens release SW

Soldering bridges of 10 pin connectors

Black:　〃　〃

#1530 TTL FPC

・Remove the soldering bridges of 10 pin connectors. ・Remove the lens contact FPC and TTL FPC from the connector. ・Remove 5 soldering bridges of AF-PI FPC. ・Take out the screws (#1503 and #1530).

5 soldering bridges of AF-PI FPC.

- Ｄ19 ･

-

VBA10601-R.3665.A

2. Remove Main FPC 2 　・Remove the screw (#283), press-contact plate (#282) and press-contact rubber (#285) to remove the main FPC 2 from the front body.

#283

#282

#285

Main FPC 2

Prism Box 1. Separate Prism box unit from Front body #1188×4

＊ When the prism box is detached from the front body, be sure to make the inspection and adjustment of parallax on Page A48.

　・Take out 4 screws (#1188). 　・Remove the prism box unit, then the washers for alignment & adjustment (#1180 and #1181) come off. #1180 #1181

- Ｄ20 ･

-

VBA10601-R.3665.A

2. Remove S. I unit ③ Take out 2 screws (#1577) to detach the S. I. unit.

① Remove the penta dust-proof tape (#1205).

#1577×2

S. I. unit

#1205

② Remove 8 soldering bridges of the penta FPC.

3. Remove Penta FPC unit (in case Penta FPC is NOT replaced）・Take out 2 screws (#1551) to detach the right-display LCD unit. ・Take out 2 screws (#1551) to detach the bottom-display LCD unit. ・Take out 2 screws (#1565) to detach the AE sensor holder unit attached to the penta FPC. ・Detach the penta FPC from the penta, (which is attached with the both-sided adhesive tape.)

#1565×2 Penta FPC unit

AE sensor holder unit

Right-display LCD unit #1551×2

Bottom-display LCD unit #1551×2

- Ｄ21 ･

-

VBA10601-R.3665.A

3-1. Remove Penta FPC unit（in case Penta FPC is replaced） #1133×3

・Take out 2 screws (#1551) to detach the right-display LCD unit. ・Take out 2 screws (#1551) to detach the bottom-display LCE unit. ・Take out 3 screws (#1133) to detach the AE sensor holder. ・Remove 3 springs for AE device adjustment (#1134). ・Detach the penta FPC unit from the penta, (which is attached with the both-sided adhesive tape.)

Penta FPC unit

#1134×3

Right-display LCD unit #1551×2

Bottom-display LCD unit #1551×2

4. Remove Eyepiece holder unit C and B #1544×3

#1120

・ Detach the 2 hooking parts of the eyepiece cover (#1104) by loosening them. ・Take out 3 screws (#1544) to detach the eyepiece top cover (#1120). ・Take out 2 screws (#1567) to detach the eyepiece holder unit C (#B1119). ・Detach the eyepiece holder unit B (#B1118).

#B1118

#B1119

Hooking part×2

#1104

- Ｄ22 ･

-

#1567×2

VBA10601-R.3665.A

5. Screen, Prism, and other small parts Both-sided adhesive tape (#1194)

・ Unscrew #1562 to remove the retaining spring (#1170). ・Remove the right-display prism (#3012) and the prism mask (#1166). ・Remove the screen by unhooking the convexity A of the screen frame from the hooked part of the finder field frame A. ・Remove the screen frame (#1102) by detaching the supporting shaft for the screen frame (#1103). ・Remove the S. I. display plate by unhooking the convexity A of the S. I. display plate from the fixed frame (#1105).

#1114

#1112×2

#B1111 #1113

Prism

Finder field frame A

Hooked part of Finder field frame A Hooked part of #1105

#1105

#1166

#1196

#1191

#1193 #1197

#3012

#1192

#1562

#1195 #1170

Prism box #1103 Finder field frame B

・Remove 2 penta retaining springs (#1112). ・Remove the penta retaining plate (#B1111) and penta insulating sheet (#1114), (which are attached in one with the both-sided adhesive tape.) ・Remove the penta retaining sheet (#1113). ・Remove the prism. ・Remove the finder field frame A. ・Remove the fixed frame (#1105). ・Detach 2 sponges (#1199) and remove the finder field frame B.

#1198×2 #1199×2 S. I. display plate

Convexity B Screen

Screen frame Convexity A

- Ｄ23 ･

-

VBA10601-R.3665.A

AF detector unit 1. Remove AF detector unit

#295×2

・Detach the E ring (#298) to remove the washer (#294). ・By using the Hexagonal wrench (φ1.5mm), take out 2 screws (#295) and 2 washers (#300). ・Remove the AF detector unit. ・Remove one spring (#293) and 2 springs (#296).

#298 #294

#300×2

AF detector unit

* Even in case the AF detector unit is not replaced, by going to the below 2 instruction without removing the above E ring and 2 screws, it is possible to remove the AF detector unit attached to the AF detector installing plate.

#296×2 #293

2. Remove Press-contact base plate and AF detector installing plate #1588×2

・Take out 2 screws (#1530) to remove the press-contact base plate (#281). ・Take out one screw (#1523) and 2 screws (#1588) to remove the AF #1530×2 detector installing plate (#B297).

#1523 #B297

#281

- Ｄ24 ･

-

VBA10601-R.3665.A

Bayonet mount, Apron, Remote connector (10 pins) #47

#41 #555 #407

#410×2

#B388 #387 #383

#406 #B404 #402 #401

#B22

#1508×4 #1572×4

#1573

Lens release SW unit, SCM change unit, Lens release button, Vertical lever unit #379

#B371

・ Unscrew #1532 to remove the lens release SW unit (#B378). ・Take out 2 screws (#1508) to remove the SCM change unit (#B10384). ・Unscrew (#379) to remove the lens release button (#376) and spring (#380).

#1512×2 #B356 #1508×2

#374

#1532 #1604

#B378

#B10384 #380 #376

・Take out 2 screws (#1512) to remove the vertical lever unit (#B356).

- Ｄ25 ･

-

VBA10601-R.3665.A

P － F・FPC (Preview & Function FPC）

TA-0023 (25 x 25)

Yellow: Release solenoid (+) Green:　　〃〃

　　(-)

Yellow:Aperture stop solenoid (+) Green:　　　〃〃　 (-) Orange: Aperture PI Blue:　　〃〃 Brown:　　〃〃 Black:　　〃〃 Green: Aperture start solenoid (-) Yellow:　　〃〃　　(+)

P － F ・FPC #1505×4

#99

#100

- Ｄ26 ･

-

VBA10601-R.3665.A

F-F0 Substrate, Lens contact unit

・Remove the soldering bridge of A part to detach the lens contact unit and F-F0 substrate. Note)To prevent the pattern from being separated, when making soldering bridges of A part, use the soldering iron with 300℃～ 320℃ of tempereture tip. Lens contact unit A part 3 soldering bridges

A part #1510 #408

F-F0 Substrate

Both-sided adhesive tape (#409)

Horizontal lever unit

Horizontal lever unit

#1521×2

- Ｄ27 ･

-

#1508

VBA10601-R.3665.A

AF driving PCB unit #1596×2

#377 × 2

AF driving PCB unit

#1594×3 #322×2

#6016 #6015

#332 #334 #1601 #350

#335

#336

#351

IL base plate unit #1524 #1524 #1533×2

#1524

#1524

- Ｄ28 ･

-

VBA10601-R.3665.A

TTL- FPC unit, I base plate unit, L base plate unit, Mirror holder unit #171

#B10204 Spring #262

#221

・ Take out 2 screws (#1508) to detach the installing plate (#302) and TTL-FPC unit (#B15009). ・Unhook the mirror-down spring (#262) that is hooked on the mirror holder. ・Unscrew #171 to separate I-base plate and L-base plate. Note: When separating the I-base plate and L-base plate, the mirror holder (#B10204) and washer (#221) come off. Be careful NOT to lose them.

#B15009

#171

#1508×2

#133×3 #134×6

#302

Front body small parts #557

#550

#1604×2

#206×2

#97×2 #96×2

- Ｄ29 ･

-

VBA10601-R.3665.A

Assembly / Adjustment 1. Front body Front body small parts

Oil barrier OS-30MF

#557

#550 Oil barrier OS-30MF

#1604×2

#206×2

#97×2 #96×2 Grease: G92KA Apply on the shaft

- Ａ1 ･

-

VBA10601-R.3665.A

Attach Solenoids on I-base plate unit

Release solenoid (#133)

Ratchet gear

Locking lever 0.2 ～ 0.3

Screws #134×2 Adhesive: Screw Lock

Attach the aperture stop solenoid and fix it with 2 screws (#134) while inserting the washer (0.2 mm), etc, into the clearance so that the clearance between Adhesive: Screw Lock

Screws #134×2

the ratchet gear and the stop lever becomes 0.2 ～ Screws #134×2 Adhesive: Screw Lock

0.3mm. Lever ・When attaching each solenoid, leave a play between the lever and iron core.

Aperture start-up solenoid (#133)

Aperture stop solenoid (#133)

- Ａ2 ･

Iron-core of solenoid

-

VBA10601-R.3665.A

Mirror holder unit, L-base plate unit, I-base plate unit, TTL - FPC unit Grease:92KA

Grease: NK-A7420

Shaft holes on A side × 2 L-base plate

Grease: NK-A7420

Shaft hole on B side

#B10204 After assembling the mirror holder into the I L-base Grease: NK-A7420

Fig.1

plate, check a play. In case it is out of standard, make an adjustment by replacing with either of the

　・ Attach the light-shielding paper (#169) on the I-base plate (by aligning their edges with 0.3-mm or less difference.) ・Assemble the mirror holder by matching the shaft of I-base plate in the 2 holes of the mirror holder on A side . (ref. Fig.1）　・Put the washer (#221) on the shaft. 　・Put the shaft of the I-base plate into the shaft-hole of the mirror holder on B side, then assemble them into the L-base plate and fix it with the screw (#171).

5 sorts (in thickness) of the washer (#221). Backlash standard：0.05 - 0.15 mm

Shaft hole of B side Spring (#262)

#221

Apply grease on the shaft where the washer (#221) is put.

#B10204 Direction A

Grease: G92KA

Ｌ -base plate

　・Pull out the mirror-down spring (#262) in the direction indicated by A, and hook it to "○" part of the #171 mirror holder.

I-base plate #B15009

　・Attach the TTL-FPC unit (#B15009) and the coupler (#302) by fixing with 2 screws (#1508). #1508×2 #302 #171

- Ａ3 ･

-

VBA10601-R.3665.A

IL base plate unit #1524 #1524 #1533×2

#1524

#1524

AF driving base plate unit

#1596×2

AF driving base plate unit

#377 × 2

#1594×3 #322×2

#6016

Grease: G7100 Apply grease on each gear and shaft

#6015

#332 #334 #1601 #350 #336

#335

#351

- Ａ4 ･

-

VBA10601-R.3665.A

Side lever unit

Apply on U-groove and receiving parts of adjustable screws

Side lever unit

Grease: G92KA

#1508

Lens contact unit, F - F0 Substrate

#1521×2

　・After attaching the lens contact unit and F - F0 substrate, make a soldering bridge of A part. Note)To prevent the pattern from being separated, when making soldering bridges of A part, use the soldering iron with 300℃～ 320℃ of tempereture tip. #408

Lens contact unit A part

Direction for positioning

3 soldering bridges

A part

#1510 #408 Both-sided adhesive tape (#409)

- Ａ5 ･

-

F - F0 Substrate

VBA10601-R.3665.A

P-F / FPC (Preview & Function FPC)

P － F / FPC #1505×4

#99

#100

TA-0023 (25 x 25) Yellow: Release solenoid (+) Green:　　〃〃　　(-)

Yellow: Aperture stop solenoid (+) Green:　　　〃〃　 (-) Orange: Aperture PI Blue:　　〃〃 Brown:　　〃〃 Black:　　〃〃 Green: Aperture start-up solenoid (-) Yellow:　　〃〃　　(+)

- Ａ6 ･

-

VBA10601-R.3665.A

Vertical lever unit, Lens release button, SCM change unit, Lens release SW unit #379 　・Assemble the release pin unit (#B371) into the vertical lever unit (#B356). Then, put the #B371 spring (#374) onto the pin and fix them with the E ring #1512×2 (#1604).

　・Attach the vertical lever unit (#B356) and fix it with 2 screws (#1512). 　・Attach the lens release button (#376) and the spring (#380), then fix them with the screw (#379).

#B356 #1508×2

#374

#1532 #1604

#B378

#B10384 #380

　・Attach the SCM change unit (#B10384) and fix it with 2 screws (#1508).

#376

　・Attach the lens release SW unit (#B378) and fix it with the screw (#1532). Remote connector (10 pins), Apron, Bayonet mount

- Ａ7 ･

-

VBA10601-R.3665.A Height adjustment of Aperture lever

● Measure the height of the aperture lever by using the tool (J18004). Aperture lever

Adjustable screw

　 Standard：3.4

～ 3.45 mm

　 In case the height of the aperture lever is out of

Adhesive: Screw Lock

standard, make a adjustment by turning the adjustable

After adjustment

screw.

Height adjustment of AF coupling shaft (#351)

① Set the SCM change lever (#383) to S. 　 After pressing the lens release button a few times, measure the height of the AF coupling ring shaft (#351). 1.7±0.15 mm Bayonet face

Lens release pin

Lens release button #351 Adhesive: Screw Lock

#359

After adjustment

- Ａ8 ･

② Adjust the hight of the AF coupling ring shaft by the screw (#359). ③ When the height of the lens release pin becomes 0.4mm, check if the AF coupling ring shaft does NOT protrude from the bayonet face. ④ After the adjustment, fix the screw (#359) with the Screw Lock.

-

VBA10601-R.3665.A

AF detector unit 1. Attach AF detector base plate, Press-contact base plate 　・Fix the AF detector base plate (#B297) with 2 screws (#1523 and #1588). 　・Fix the press-contact base plate (#281) with 2 screws (#1530).

#1588×2 #1523 #B297

#1530×2

#281

2. Attach AF detector unit ・Screw up then rotate 2 turns counterclockwise. #295×2 #298

　・Put 1 spring (#293) and 2 springs (#296) on the AF detector base plate (#B297).

#294

#300×2

　・Attach the AF detector unit.

AF detector unit

　・Put 2 washers (#300) and attach 2 screws (#295) by using Hexagonal wrench (φ1.5mm ). #296×2

　・Screw 2 screws (#295) up and give them 2 turns counterclockwise.

#293

　・Put the washer (#294) and fix it with the E ring (#298).

- Ａ9 ･

-

VBA10601-R.3665.A

Prism Box 1. Prism, Screen, and other small parts

・Attach 2 sponges (#1198) on the finder field frame B (#1108). (ref. Fig.1）・Assemble the finder field frame B (#1108) into the prism box, then attach the sponge (#1199). （ref. Fig.2）・Enter 2 claws of the fixed frame (#1105) into 2 grooves of the prism box to attach them. ・Attach the finder field frame A. ・Attach the prism. ・Attach the penta retaining sheet (#1113). ・Attach the penta retaining plate (#B1111) and fix it with 2 penta retaining springs (#1112). ・Attach the penta retaining insulating sheet (#1114).


#1114

#1112×2

#B1111 #1113

・Attach the prism mask (#1166) to the right-display prism (#3012), then assemble them

Prism

into the prism box. ・Attach the retaining spring

Finder field frame A Hooking part

(#1170) and fix it with the screw (#1562).

#1105 #1166

Claw ×2

#1196 #1193

#1191

#1197

#3012

#1192

#1562

#1195 #1170

Prism box Groove ×2

Finder field frame B

#1103

・Put the stepped part of the S. I. display plate into the clearance of the prism box, then hook the convexity to the hooked part of the fixed frame (#1105) to fix the S. I. display plate. 　　（ref. Fig.3）・Put the 2 legs of the screen frame into the prism box, then insert the supporting shaft of the screen frame (#1103) sideways to fix them. ・Put the screen on the screen frame, and hook the convexity of the frame to the hooked part of the finder field frame A to fix them.

#1198×2

Fig.1 Position for attaching #1198

#1198×2

#1199×2

#1199×2

S. I. display plate Fig.2 Position for attaching #1199 Screen

Hooking part of #1105 Prism box

Screen frame

- Ａ10 ･

-

Convexity

Stepped part of #3004 Fig.3

Convexity

VBA10601-R.3665.A

2. Attach Eyepiece holder unit B, C, and AE sensor holder #1565×2

#B1131

・Attach the eyepiece holder unit B (#B1118). ・Attach the eyepiece holder unit C (#B1119) and fix it with 2 screws (#1567). ・Attach the eyepiece top cover (#1120) and fix it with 3 screws (#1544). ・Hook the convexity of the prism box to the 2 hooked parts of the eyepiece cover (#1104) to fix it. ・Attach the AE sensor holder (#B1131) and fix it with 2 screws (#1565).

#1544×3 #1120

Grease: MZ-800S Apply thinly.

#B1118

Convexity Hooked part × 2

#B1119 #1567×2

#1104

3. Attach Penta-prism FPC unit ・Attach the penta-prism FPC unit to the penta. ・Put the 3 AE sensor adjustment springs (#1134) into the 3 shafts (#B1131). ・Assemble the AE sensor holder

Rotate 7 turns #1133×3

Penta-prism FPC unit

and fix it by giving the 3 screws 7 turns (#1133). Note) Do NOT screw up the 3

#1134×3

screws (#1133) because it may damage the AE sensor. ・Attach the bottom-display LCD unit and fix it with 2 screws　 (#1551). ・Attach the right-display LCD unit and fix it with 2 screws　(#1551).

#B1131 Right-display LCD unit

Direction for position #1551×2

Bottom-display LCD unit Direction for position

- Ａ11 ･

-

#1551×2

VBA10601-R.3665.A

4. Attach S. I unit #1577×2

Soldering bridge×8

(temporarily attached)

S. I unit

A part

・Put the A part of the soldering bridge of the Direction for position penta FPC into the A part of the S. I unit.

Penta FPC A part

#1205

5. Attach Prism box unit to Front body #1188×4

Note:When the prism box unit is detached, be sure to make a fine adjustment by following the instruction on A48 Page.）

・Attach washers for alignment and adjustment (#1180 and #1181). ・Attach the prism box unit and fix it with 4 screws (#1188). #1180 #1181

- Ａ12 ･

-

VBA10601-R.3665.A

Angle adjustment of Main mirror and sub-mirror to 45° Collimator Mirror 45 deg. inspection tool

Bayonet mount

Eccentric pin for the main mirror

J18356

Mirror of J18352

Main mirror

Sub-mirror After adjustment Adhesive:Screw Lock

#1526×2 Adhesive:quick dry glue After adjustment

＊ Tools required 　1. When adjusting the main mirror 　　　① Collimator（J19002) 　　 ② Mirror tool（J18356）　　　③ Mirror 45 deg. inspection tool（J18037）　　　④ Hexagonal wrench（φ1.5mm）　2. When adjusting sub-mirror 　　　① Collimator（J19002）　　 ② Sub-mirror inspection tool (J18352）　　　③ Hexagonal wrench（φ1.5mm）

Eccentric pin for the sub-mirror （The eccentric pin for the sub-mirror is outside the mirror box.） Two-pronged part of the sub-mirror

Shaft base plate for the main mirror

Eccentric pin for the sub-mirror

(#B239)

Note：Check if the two-pronged part of the sub-mirror surely fits in the eccentric pin, then measure the angle of 45°of the sub-mirror.

　・Angle adjustment of the main mirror to 45° 　　Note：Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. 　　① Check for the left-right deviation. 　　　In case the deviation is out of standard, make an adjustment by loosening 2 screws (#1526) and moving the shaft plate for the main mirror (#B239). 　　② Check for the up-down deviation. 　　　In case the deviation is out of standard, make an adjustment by turning the eccentric pin for the main mirror. 　・Adjustment of the sub-mirror to 45° Note：Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. ① Check for the up-down deviation. 　　　In case the deviation is out of standard, make an adjustment by turning the eccentric pin for the sub-mirror. The width of line indicates deviation.

　 Standard Main mirror

Sub-mirror

Left-right deviation

±20′

±20′

Up-down deviation

±5′

-5±5′

Distortion

5′

8′

Up-down

Reference line Left-right

- Ａ13 ･

-

VBA10601-R.3665.A

∞ Infinity alignment & adjustment

　・Replace the finder screen with the infinity focus check screen for D2H（J15408), and use the reference lens （J18010）and read its scale. Note: Put the infinity focus check screen (J15408) with its "No. seal" being on the underside (i.e. main mirror side) and also on near side (i.e. bayonet side).

　　Standard scale：-0±2

No. seal

　How to adjust 　　Make an adjustment by using the washers for prism box (#1180 A-L and #1181 A-L). （ref. Fig. of Page A12）

Main FPC 2 1. Attach Main FPC 2 　・Attach parts in the order of the 3 AF detector FPCs, the main FPC 2, the press-contact rubber (#285), and press-contact plate (#282), then fix them with the screws (#283).

#283

#282

#285

Main FPC 2 AF detector FPC ×3

- Ａ14 ･

-

VBA10601-R.3665.A

2. Attach Wires, FPCs, and soldering bridges 　・Attach the screws (#1503 TA-0022 and #1530). 　・Make soldering bridges for (10×20) AF-PIFPC at 5 parts. 　・Connect the lens contact FPC and TTLFPC to the connector.

Red: AF motor Black: AF motor Black: Lens contact FPC

Lens contact FPC

#1503 Red: SCM change Blue:　〃　〃 Brown:　〃　〃 Gray: Lens release SW

Soldering bridges for 10 pin connectors

Black:　〃　〃

#1530 TTLFPC

　・Make soldering bridges for 10 pin connectors. 　・Solder the grey and black wires that connect from the lens release SW and the red, blue and brown wires that connect from the SCM change. 　・Solder the red and black wires that connect from the AF motor and the black wire that connects from the lens contact FPC.

Soldering bridges for AFPIFPC at 5 parts

Diopter adjustment unit Enter A-part of the diopter adjustment unit into this groove.

Grease: G92KA Apply to the all-around inside diameter.

Positioning mark

A part Centrally positioned

A-part

Diopter adjustment unit #1535

- Ａ15 ･

-

VBA10601-R.3665.A

2. Rear body Rear body small parts

#575 #566 #574 #576

#398

#567

#397

#573

#399

#572

#565

#271

#564 #563 #571

#568

#569 #561

#577-1

#562

#554 #595

- Ａ16 ･

-

#533

VBA10601-R.3665.A ④ ① Temporarily attached #1704×3

Shutter unit ②

③

Shutter unit

　・Attach the dust-proof sheet (#540) to the both-sided adhesive tape (#533). 　・Attach the shutter unit and fix it with 3 screws (#1704). #540

Note: Tighten the 3 screws (#1704) in the order from ① to ④ .


SQ (sequence) PCB unit 1. Attach Charge SW brush, Charge motor TA-0005 (12×6） Charge SW

#1566×2

TA-0005 (18×18） #1569

Yellow and black wiring

Black, brown and red wiring

Charge motor Grease： G92KA

#606×2

- Ａ17 ･

-

VBA10601-R.3665.A

2. Operational check of SQ PCB unit Upper part of charge roller

Apply on side faces of the charge roller and lever. Grease: G92KA

After the operational check, step down voltage and when the upper part of charge roller is positioned as shown above, turn the power OFF.

　・Connect the red and black wires of the charge motor to "9V", and measure the consumed current in operation.

Stabilized power supply

　Standard：150 m A or less

Set value 9V 2.0 Ａ

3. Attach SQ PCB unit to Rear body #1538×4

#683 SQ PCB unit

・Attach the SQ PCB unit and fix it with 4 screws (#1538).

Shutter FPC

・Fix the shutter FPC on the SQ PCB with the screw (#683).

- Ａ18 ･

-

VBA10601-R.3665.A

CF card PCB plate unit 1. Attach CF card PCB plate unit on CF fixed plate unit #1530×3 CF card PCB plate unit #449

・Assemble the CF card PCB plate unit into the CF card fixed plate unit. ・Put the CF knob cover (#449) on the CF card PCB plate unit, and fix them with 3 screws (#1530).

CF fixed plate unit

2. Attach 2 Fixed plates on DC/DC PCB unit 2 #1540

・Attach the power transistor (#5086) on the fixed plate (#70) with the screw (#1540).

#1530×2

#5086

DC/DC PCB unit 2

Fixed plate (#70)

・Attach the fixed plates (#69 and #70) on the DC/DC PCB unit 2, and fix them with 3 screws (#1530). ・Solder the 3 legs of the power transistor (#5086) on the backside of the DC/DC PCB unit 2.

Solder the 3 legs of the power transistor.

#1530 Fixed plate (#69)

- Ａ19 ･

-

VBA10601-R.3665.A

3. Assemble Memory compression PCB plate and DC/DC PCB unit 2 Note: When the memory compression PCB is replaced, be sure to check the firmware version of RISC by the shooting image adjustment software. If it is not the updated version, upgrade the firmware by following the procedure on Page A62.

Memory compression PCB plate

・Solder black and red wires on the DC/ DC PCB unit 2. ・Connect the connection-FPC (#5035) to the connector ① .

#1530×3

Connector ① Pattern face of #5035 Connector

・Connect the connection-FPC (#5033) to the connector ② .

Connector ②

・Connect the connectors of the memory compression PCB plate and the DC/ DC PCB unit 2, and fix them with 3 screws (#1530).

Black Red

Pattern face of #5033

DC/DC PCB unit 2

4. Attach CF card PCB plate #1530×2 CF card PCB plate

　・Connect the connectors of the CF card PCB plate and the memory compression PCB plate, and fix them with 2 screws (#1530).

Memory compression PCB plate

Connector

5. Attach DC/DC PCB unit 1 #1530×2 Black: DC/DC PCB unit 2

　・Attach the DC/DC PCB unit 1 to the fixed plate (#70), and fix it with 2 screws (#1530).

Red: DC/DC PCB unit 2

DC/DC PCB unit 1

　・Solder the black and red wires, which connect from the DC/DC PCB unit 2, on the DC/DC PCB unit 1. Fixed plate (#70)

- Ａ20 ･

-

VBA10601-R.3665.A

6. Attach CF card PCB unit to Rear body #1531×2

Bottom hole of the rear body

・Assemble the CF card PCB unit by putting it into the bottom hole of the rear body, while holding them down in the direction of the 2 connectionPCBs with fingers.

CF card eject lever

・Attach the CF card PCB unit on the rear body with 2 screws (#1531).

CF card PCB unit

2 connection-FPCs

#1531×2

　・Then, fix the CF card PCB unit with 2 screws (#1531).

- Ａ21 ･

-

VBA10601-R.3665.A

I/F PCB unit 1. Assemble DC-IN video PCB and USB PCB Soldering bridge×5

・Solder the orange and black wires inside the DC-IN video PCB, and the red, orange and black wires outside the DC-IN #1526×3 video PCB, then fix the wires with the adhesive (SC 608Z). #1526×3

・Attach the TA-0022 (20×10) to cover the soldered parts of the orange and black wires inside the DC-IN video PCB.

USB PCB DC-IN video PCB

IF PCB fixed plate Black: Main FPC 2 Orange:　　〃　〃

・Fix the DC-IN video PCB on the IF PCB fixed plate with 3 screws (#1526).

TA-0022 (20×10）

・Fix the USB PCB on the IF PCB fixed plate with 3 screws (#1526). ・Make soldering bridges at 5 parts.

2. Attach I/F PCB unit to Rear body Orange and black wires

・Pass the orange and black wires, which connect from the upper I/F PCB, through the hole A of the rear body.

I/F PCB unit Hole A

・Assemble the I/F PCB unit into the rear body, and tighten firstly the 2 screws (#1523) then the screw #1523×2 (#1510) to fix them.

#1510

- Ａ22 ･

-

Red:DC/DC PCB unit 2 Orange: 〃〃 Black: 〃　〃

VBA10601-R.3665.A

3. Solder red, orange and black wires

・Solder the 3 wires (in red, orange and black) to the DC/ DC PCB unit 2.

TA-0005 (20×10)×2

・Fix the red, orange and black wires with 2 pieces of tape (TA-0005: 20×10) for arrangement.

DC/DC PCB unit 2

Red: I/F PCB Orange: I/F PCB Black: I/F PCB

- Ａ23 ･

-

VBA10601-R.3665.A

3. Mount Front body on Rear body Mount the front body on the rear body #1590×2

#1535 Adhesive: Screw lock After attaching the screw (#1535)

#1514×6 ②

　・Mount the front body on the rear body. 　・Attach 6 screws (#1514) in the order of ① - ⑥ . 　・Attach 2 screws (#1590) under the eyepiece. 　・Attach the screw (#1535).

③

⑥ ⑤ ①

④

Black: I/F PCB 　Orange: I/F PCB

　・Solder the black and orange wires that connect from the I/F PCB.

- Ａ24 ･

-

VBA10601-R.3665.A

Inspection and Adjustment of Body back 　・"0" positioning of the dial gauge Index ring

②

"0" position of D2Hs

Measurement terminal ①

Washer

Surface plate

①　Put the tool （J18001-1） on the surface plate. ②　Put the washers totalling 0.23 mm in thickness (e.g. 0.07-mm 1 washer and 0.08-mm 2 washers, totalling 3 washers) between the tool (J18001-1) and the measurement terminal of the gauge, and turn to set the index ring to "0". (Set the digital gauge to "0".) (This position is "0" of D2Hs.)

・ Measure 6 parts from the bayonet face to the image PCB attaching face. 　 × mark: to be measured 　 Standard: 47.9±0.015mm / within 0.015mm ・ In case it is out of standard, make an adjustment by putting the washer on the contact surface between the front body and rear body.

Note: For some bodies, the washer is already put on the attaching face of the image PCB . There is an indication of the mark in red at the following 2 positions. 　 1. Indication: on the camera body side of the image PCB attaching face 　　　 Purpose：To adjust the height of the camera body 　 2. Indication: on the image PCB attaching face 　　　 Purpose：To adjust the height of the image PCB Therefore, for the above 1 with the red mark, in case its camera body is disassembled or the image PCB is replaced, insert the washer at the original position. For the above 2 with the red mark, in case its image PCB is replaced, remove the washer.

- Ａ25 ･

-

VBA10601-R.3665.A

Back-up battery box unit Red: Back-up battery box Black: Back-up battery box

・Pass the red and black wires of the backup battery box (#B818) through the hole B of the rear body to assemble, and fix them with 2 screws (#1533). ・Solder the red and black wires on the USB PCB.

#1533×2

#B818

Hole B

Main FPC 1 unit

#1566×3

Note: When the main FPC 1 is replaced, be sure to write the EEPROM fixed values by the adjustment software. If the main FPC 1 is replaced with the new one, the camera does not work properly until the fixed values are written by the adjustment software.

Main FPC 1

Main FPC 2

　・Attach the main FPC 1 and fix it with 3 screws (#1566). 　・Connect the connection-connectors of the main FPC 1 and main FPC 2.

- Ａ26 ･

-

VBA10601-R.3665.A

　・Attach the screw (#1553). 　・Connect the penta FPC (#B15005) to the connector. 　・Connect the shutter FPC (#5014) to the connector. 　・Connect the P-F (Preview & Function) FPC (#5027) to the connector. 　・Solder 3 wires (in red, brown and black) that connect from the charge SW. 　・Attach the retaining tape (#684) to cover the main FPC 1 and 2.

#5027

Position for attaching #684

Condenser

#684

#5014

Brown: Charge SW Red: Charge SW Black: Charge SW #B15005 #1553 TA-0005 (6 X 12)

　・Attach 2 screws (#1532). 　・Connect the connection-FPC of the main FPC1 & memory compression PCB (#5035) to the connector. 　・Connect the connection-FPC of the main FPC1 & DC/DC PCB unit 2 (#5033) to the connector. 　・Solder the red and black wires of the side face of the main FPC 1.

Connector Connector

#1532×2

Yellow: Charge motor

#5033

Black: Charge motor

#5035

Main FPC 1 unit

- Ａ27 ･

-

VBA10601-R.3665.A

Top cover unit Note： The environment light sensor-FPC on the top cover is, after being fixed with the retaining plate, adjusted by the special equipment at factory. If the environment light sensor is moved even just a little by loosening the screw of the retaining plate, the readjustment becomes necessary. So, be sure NOT to loosen or remove the screw of the retaining plate for repairs. (ref. Fig. 1)

Retaining plate

Fig.1 screw Top cover unit

When the environment light sensor-FPC needs to be repaired or replaced, replace the top cover unit and make a note of triple-digit adjustment value written on the top cover unit. (Input the adjustment values in 5 rows of “R”, “B”, “G”, “T”, and “A/D” when the AWB adjustment for camera adjustment is made.) Adjustment values:

Environment sensor-FPC

R: Adjustment value of R-output of environment light sensor B: Adjustment value of B-output of environment light sensor G: Adjustment value of G-output of environment light sensor T: Temperature data when adjusting

Adjustment values in 5 rows

A/D: A/D value of temperature output A of environment light sensor

Top cover unit of repair parts

1. Accessory shoe, Eyelet, and other small parts #773 Accessory shoe

KE347B

#B772 Eyelet #192 Adhesive: C-8008B

Eyelet Adhesive: Loctite

#1585 Adhesive: Loctite

#777

#1631 Adhesive: C-8008B After attaching #1631, apply to #768 the all-round part.

#778 #768×4 #765×2

#766×2

- Ａ28 ･

-

VBA10601-R.3665.A

- Ａ29 ･

-

VBA10601-R.3665.A

3. Release button, Top cover FPC, Mode dial, Top LCD window, and other small parts Grease: G92KA

Top LCD window

� Mode dial

#508 #509


#1569×3

Yellow：Top cover FPC

#50 #1501 Adhesive：Loctite

�

#513

Release button #733

#750

Grease: G92KA

#734 #750 Spring hooked

#B24

#751

#502

#1604 4 soldering bridges

#501 Top cover FPC

�

#5017

#516

#515 Connector

#514 #503

Yellow: Top cover FPC

#505

Brown: Top cover FPC #1582×2 #519 #1566

�

#506

- Ａ30 ･

#1570×2

-

VBA10601-R.3665.A

4. Main and Sub-C/D (Command dial) unit, Release contact blade, Sponge

#761

Grease：OS-30MF

#762

#559

Grease：OS-30MF

Grease：OS-30MF

#560

Grease：OS-30MF

Release contact blade

#763×2

#1575

Grease：OS-30MF

#764×2 Grease：OS-30MF

Main C/D PCB unit

・Environment sensor FPC and 9 soldering bridges

#1566×2

Sub C/D PCB unit

Release switch FPC

#1703×2 #560 Grease：OS-30MF

#518 Adhesive：SC-608Z

- Ａ31 ･

-

VBA10601-R.3665.A

5. Attach temporarily Top cover unit to Camera body unit

Top cover unit

B1137

・Assemble the eyepiece block unit (#B1137) and attach the top cover unit temporarily. （The top cover attaching-screw is not used until the AE CCD alignment inspection and adjustment are completed.）・Connect the top cover FPC to the connector. 　・Solder the red and black wires, which connect from the back light for the top LCD, on the main PCB.

Top cover FPC

Adhesive：SC608Z

Red : Back light for top LCD (EL) Black : Back light for top LCD (EL)

- Ａ32 ･

-

VBA10601-R.3665.A

Inspection and adjustment of AE CCD Alignment In case the penta-prism FPC unit is disassembled or replaced, or in case the prism box unit is disassembled or replaced, be sure to inspect and adjust the AE CCD alignment. ・Attach 3 screws (#1133) by giving 7 turns for X,Y and Zscrews. ・ Remove the S. I. display plate in the finder with the tool (T93004), then put the CCD positioning tool (J15406) and the finder screen. ・Select "CCD ALIGNMENT INSPECTION AND ADJUSTMENT" in "INSPECTION AND ADJUSTMENT FOR AE CCD POSITION" of the adjustment software, and follow the instruction for inspection and adjustment. 　　Refer to Page A35 for how to connect between the camera and PC. Note: Assemble the top cover and eyepiece block unit that were temporarily attached when making an inspection. When an adjustment is made, lift the top cover from the body and measure by covering the AE CCD unit with a black cloth, etc to darken.

Z

Y

X

　・Turn the X or Y screw and make an adjustment until the PC indication gets within the standard. 　・It is favorable NOT to turn the Z screw too much because it is the reference screw. However, in case there is no alternative, turn it for the adjustment.

Output of AE CCD

Y direction

X direction

- Ａ33 ･

-

VBA10601-R.3665.A

　・Attach 2 screws on the front cover side of the top cover, and also attach 2 screws under the eyepiece.

#1537×2

#1516×2

　・Select "CCD SLANT INSPECTION" in "INSPECTION AND ADJUSTMENT FOR AE CCD POSITION" of the adjustment software. Then check the inclination of the AE CCD. 　・This is only for inspection and adjustment is impossible. In case the result is out of standard, follow the instruction of "CCD ALIGNMENT INSPECTION AND ADJUSTMENT" of the previous page again. However, it is still out of standard even after this, replace the penta-prism FPC unit.

　・PC screen

- Ａ34 ･

-

VBA10601-R.3665.A How to connect Camera and PC

★：Newly prepared tool

The straight cable of the marketing article

MC-31

AC adapter （EH-6） To RS 232C terminal

Inspection and adjustment FD for D2Hs camera J18382 ★

9pin-25pin adapter is necessary for a computer with 9-pin RS-232C terminal. RJ is not available

Pic. 1. Shutter tester

　・When AE inspection and M1/8000 adjustment are made, use the sensor for APS and the sensor adapter (J61199) as shown left, because the shutter size of D2Hs is APS size. (When they are used, fix them with fingers so that the 3 holes for attaching the image PCB can be seen as shown in the Pic. 1.) Note) When using the shutter tester to inspect and adjust the camera, turn the tester to ON and light the lamp for 3-5 mins. for aging. J61199 　Sensor adapter（Common with D100）　 J19042E 　Shutter speed measurement adapter

Traditional adapter for camera

J19042D

- Ａ35 ･

-

VBA10601-R.3665.A

D2Hs Inspection and Adjustment Software (J18382) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. The following operating environment is required for installing this program on PC. PC OS CPU RAM (memory) HD Monitor resolution Interface

IBM PC/AT compatible Windows XP Professional Edition,Windows XP Home Edition, Windows Millennium Edition (Me), Windows 98 Second Edition (SE), Pentium 2 ～ Pentium 4 32MB or more 6MB-or-more free disk space is required when installing 800×600 pixels or more Serial Interface ※ USB Interface is not available.

As long as the above hardware requirements are met, any PC such as desktop or laptop, etc is available.

When starting this program, close all the other applications. If some other applications are running, this program may not be activated.

The file (D2HsSOFT.EXE) of this program is provided via FD or e-mail. Because this is the self-extracting file, decompress the file before installing, following the next procedure. 1. Create a folder for installation under a name you like and PC drive. 　　(e.g.) C:\D2Hs

- Ａ36 ･

-

VBA10601-R.3665.A

2. Paste the file (D2HsSOFT.EXE) in the created folder. 　　　　　

3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts. 　　　　　

4. When the decompression of file is finished, the file (D2Hs.EXE) is created. 　　　　　

5. The installation is completed.

- Ａ37 ･

-

VBA10601-R.3665.A

＜ Start-up of Program ＞ 1. Double-click on File (D2Hs. EXE). The screen of warnings and cautions when connecting D2Hs and PC and turning on D2Hs will be displayed. Without following these instructions, the inspection and adjustment cannot be made correctly.

If the program is started in Japanese version next time, the following screen will be displayed.

- Ａ38 ･

-

VBA10601-R.3665.A

2. Press "CLOSE WINDOW" button of the previous "1." to start the Inspection & Adjustment program for D2Hs. 　　　　　

3. To display in Japanese, select the radio button "JAPANESE" in "LANGUAGE" in the lower right-hand corner of the screen ". However, this is not properly viewed in the OS in English version 　　　　　

4. When the "HISTORY" button at the lower-left is pressed, the program version will be displayed. 　　　　　

5. Select each item button according to operation. 　Follow the instructions on the next screen that will be shown after pressing the item button. 6. To finish the program, press the "Close (×)" button in the right-hand corner of the screen or "CHANGE TO SYSTEMS".

- Ａ39 ･

-

VBA10601-R.3665.A

Adjustments on PC (for Camera body） 1. AE adjustment Follow the instruction of the adjustment software for each adjustment. 1. AE CCD positioning inspection and adjustment (ref. Page A33） 2. AE accuracy inspection and adjustment Note：The AE accuracy check is NOT based on the compensation value for which the traditional shutter tester is used. The measured value is displayed on PC. 3. Aperture accuracy inspection 　Note：For aperture inspection, the aperture pulse number is displayed on PC screen. 4. Ｍ 1/8000 accuracy inspection and adjustment 5. TTL inspection and adjustment Note：The traditional time-counter and grey shutter curtain (standard reflex paper) are NOT necessary. The results are displayed on PC screen. 6. AF PI duty adjustment 7. AWB adjustment This adjustment is for recognizing illuminated color temperature correctly when lights with various color temperature are illuminated on environment light sensor. 2. AF adjustment

Note: If this adjustment software is used for the first time, prepare 3 units of D2Hs and get the data by "WRITING OF AF ADJ. LENS OFFSET VALUE" on the main menu. In case there is "LDATA" file of D2H or D2X in the same PC, copy it in the folder of D2Hs adjustment software and change "H" of "D2HLDATA" to "Hs" or "X" of “D2XLDATA” to "Hs" for use.

〔Inspection/adjustment items〕　①　AF accuracy inspection and adjustment (Make all the following adjustments.) 　②　YAW, PITCH 　③　CCD output adjustment and focus adjustment ④　AF shift adjustment 　　〔Tool〕 1. When adjusting for all adjustment items, use 　　the same tool as AE-related. 2. When inspecting AF accuracy, use 　　① AF adjustment lens (J18266) 　　② AF adjusting tool (J15259) 　　③ Lens holder for F4 (J15280) or Adapter for tripod (J15271) 　　④ AF chart (J15407) ⑤ Chart board for J15047 (J15409) 　　⑥ Chart illuminator for AF (J15264） 3. When adjusting YAW / PITCH, use 　　① The above tool when inspecting AF accuracy 　　② YAW, PITCH tool (J18230) 4. When adjusting focus, use 　　the above tool for inspecting AF accuracy 5. When adjusting CCD output, use 　　AF 50/1.4D lens

- Ａ40 ･

-

VBA10601-R.3665.A

Imaging (LBCAST) PCB unit 1. Attach Image PCB unit 　・Assemble the frame (#529).

③

　・Connect the image PCB harness to the connector. 　・Connect the connection-FPC of the image PCB & memory compression PCB (#5038) to the connector.

Connector

①

　・Attach the image PCB unit, and fix it with 3 screws (#525) in the order of ① - ③ .

②

#525×3

Image PCB harness

Image PCB unit

*A part #529

Note 1: For some bodies, the washer is already put on the attaching face of the image PCB. There is an indication of the mark in red with magic marker. Refer to Page A25 in the Assembly chapter for the details.

#5038 Connector

*Note 2: For some bodies, there are L-shaped washers attached at 3 parts of A-part on the image-PCB. On such PCB, there is red-marked indication on its attachment side, so if the washers come off, reattach them. In case the PCB is replaced with the one without red marking, the washers are NOT necessary.

Direction for positioning of Image PCB

Reference for attachment

- Ａ41 ･

-

VBA10601-R.3665.A

2. Attach Image PCB cover plate

#5040

Lower side is pattern face

Upper side is pattern face

　・Attach the image PCB cover, and fix it with 2 screws (#1530).

#592 #578

　・Attach the tape (#578) in position as shown right. 　・Attach the sheet for EMI prevention sheet (#592) on the connection-FPC (#5040).

Image PCB cover plate

#1530×2

0.5 ～ 4mm

0.5 ～ 4mm

　・Connect both ends of the connectionFPC of the memory compression PCB & UBS PCB (#5040) to the connector.

1. Attach Battery case upper unit, Battery contact unit 　・Attach the battery case upper unit (#B823) (attached with both-sided adhesive tape) by aligning it with 2 bosses, and fix it with the screw (#1520). 　・Attach the battery contacts unit (#B801), and fix it with 2 screws (#1515) and 1 screw (#812). 　・Connect the battery contact connection-FPC to the connector. #812

#1520

#1515×2

Battery contact conection-FPC #B801

#B823

Connector

- Ａ42 ･

-

VBA10601-R.3665.A

2. Solder wires

　・Solder red and black wires that connect from the battery contacts.

Black: Battery contact Red : Battery contact

TFT － Memory compression PCB connection-FPC 　・TFT - Connect the memory compression PCB connection-FPC (#5041) to the connector of the memory compression PCB. #5041

Valley fold

Pass the connection-FPC through the lower hole (#5041), and make a valley fold.

Connector Lower hole

- Ａ43 ･

-

VBA10601-R.3665.A

Back door unit 1. Multi-selector, AF area mode select dial, and other small parts Apply to periphery of #474. Grease: G92KA

#1561×2 Multi-selector

#B468 #469 #474

#434×2

#435×2 Grease: G92KA

AF area mode select dial #465

#494×2 #450 #493×2

#472 #473 #1531×2

#470 #422 #1533×3

#B478

2. Microphone, Speaker, TFT PCB, and other small parts #425

#453

#445 #427

Adhesive: EDZ4113

�

#1513×2 #B428

Grease: G92KA To overall edge �

TFT PCB

#1522×2

#463 Speaker #1560×2

Grease: G92KA Apply on the shaft and tip

#460 #467 #442 Microphone #B439

#456

#1531×2

- Ａ44 ･

-

#1508×3

VBA10601-R.3665.A

3. Attach TFT monitor

　・Attach the TFT monitor (#5043) and the TFT retainer (#432), and fix them with 2 screws (#436).

Direct for position

#432 #5043 #436×2

　・Connect the TFT monitor FPC and AF area FPC to the connector.

AF area FPC

TFT monitor FPC

　・Solder the red and black wires of the TFT back lights. Red: TFT back light Black : TFT back light

4. Attach Back door unit 　・Connect the TFT & memory compression PCB connection-FPC (#5041) to the connector. （ref. Fig.1）　・Attach the back door unit to the camera, and fix them with 4 screws (#1514). Back door unit

Connector

Fig. 1 #5041

- Ａ45 ･

-

#1514×4

VBA10601-R.3665.A

Bottom cover unit 1. Attach Bottom cover unit

　・Attach the bottom cover unit to the camera, and fix them with 3 screws (#1512) and 3 screws (#1517).

Note: Between the bottom cover and the body (i.e. A part), there is the washer (T=0.3) inserted. When assembling, be sure to put it back into the original position. (This measure is for filling in a gap between the back door and bottom cover.)

A part #1512×3

Bottom cover unit

#1517×3

2. Connect vertically position FPC

　・Connect the vertically position FPC to the connector.

Vertically position FPC

- Ａ46 ･

-

VBA10601-R.3665.A

Grip cover ・Attach the grip cover, and fix it with 2 screws (#1534) and 2 screws (#1510).

#1534×2

#1510×2

Grip cover

I/F block ・Attach the I/F block, and fix it with 3 screws (#1589).

#1589×3

I/F block

- Ａ47 ･

-

VBA10601-R.3665.A

Parallax inspection and adjustment Note: This adjustment should be made after completing "TFT angle-of-view adjustment" of the image adjustment, because the camera is positioned via the TFT monitor screen. When "Separate Prism box from Front body" (Page D20) is performed, be sure to make the adjustment.

Procedure 　①　Insert the battery into the camera, and set the exposure mode to "P". 　②　Turn the power SW to OFF, and remove the battery. (By this procudere, the camera memorizes the latest set mode in the camera.) 　③　Remove the FPC and 2 wires of the top cover, then detach the top cover from the camera. Note: If the FPC of the top cover was removed with the battery being inserted, the power transistor, etc, of DC/DC2 may be burned out. ④　Attach the parallax-inspection chart (J15404) on the wall, etc. ⑤　Put the CF card and battery into the camera, and mount the lens AF 50/1.4. ⑥ Position the camera correctly 1 m-distance from the parallax-inspection chart by using the tripod, etc. (ref. Fig. 1.) (Set the optical axis of lens to come in the center of the chart.)

100％ frame（red）

Parallax inspection chart （J15404）

98％ frame（black）

Mounting surface of Image-PCB

AF 50/1.4

1m

Focus frame in center of Viewfinder Inspection parallax chart (J15404)

⑦ Take a shot of the chart by the shutter-release button for vertical shooting and display it on the TFT monitor to fine adjust the camera position so that all 4 sides of the 98 % chart frame can appear on the monitor. ⑧ Look through the viewfinder, then in order to meet the standard, check if all 4 sides between the 100 % frame and 98 % frame can be seen. In case it is out of standard, remove the battery and make the following adjustment.　　　 ⑨ disconnect the connector of main FPC 1 and main FPC 2

Fig.1 #1188×4

⑩　Loosen 4 setscrews for the prism box (#1188), then move the prism box so that the 4 sides in the viewing field of the finder come in between the 100％ chart frame and 98％ chart frame. ⑪　Tighten the loose 4 screws (#1188). (After tightening them, check the angle of view of the viewfinder.) ⑫　Connect the connector of main FPC 1 and main FPC 2 and insert the battery into the camera. Take a shot of the chart again by the Vertical shooting shutter button, and check if the camera is NOT displaced. In case the camera is displaced, adjust again starting from ⑦ . ⑬ Remove the battery and perform “ 5. Attach temporarily Top cover unit to Camera body unit” on Page A32. - Ａ48 ･ -

VBA10601-R.3665.A

Attach Top cover screw

#1537×2 #B1171 Top cover #B23

Note: Put the eyepiece block unit (B1137) by following the direction of the arrow (A) for positioning, then tighten 2 screws (#1537). If it is not put in position, when the monitor cover (BM-3) is attached, there increases the amount of play in this monitor cover left.

#1519

Ａ

#1130

　・Fix the top cover with 8 screws in total (1 screw:#1543, 2 screws: #1537, 1 screw: #1519, 1 screw:#1510, 2 screws:#1516, and 1 screw: #1556).

#1568 #1121 #1510

#1543

　・Attach the eyepiece diopter knob (#1121) with the screw (#1568). 　・Attach the eyepiece diopter knob cover (#1130).

#1516×2 #1556

External rubber ・Attach the grip rubber (#B60-1), apron lower rubber (#B66) and rewind side rubber (#B61).

#B61

#729

Positions for screwing top cover Do NOT allow to exceed the indicated line.

#B66 Position for attaching#729

#729

#B60-1

- Ａ49 ･

-

VBA10601-R.3665.A

Battery lid unit

#805-1

#804-1

B806 #808 #810

#809 #811

#1600×2 B828

#815

#830

#1533×2

Apply to the inside diameters. Grease: MZ-800S

#813-1 #814-1

#816-1 #1549×4

- Ａ50 ･

-

VBA10601-R.3665.A

Necessary adjustments on PC when parts are replaced 1. Adjustment software Adjustments AE CCD AE Aperture Shutter TTL position accuracy accuracy M1/8000 accuracy inspecParts to be tion replaced

Upgrading

AF PI

EEPROM of FirmAF fixed ware of A accuracy

○

○

○

○

○

○

○

○

Main FPC 2

AF detector unit

○

AF driving PCB unit

○ ○

TTL SPC unit

○

DC/DC 1

DC/DC 2

I S U B S T R AT E UNIT

and B Microcomputers

○

○

○

Shutter unit

Penta-prism FPC unit

values

○

Top cover unit

Main FPC 1

AWB

○

○ ○ - Ａ51 ･

-

VBA10601-R.3665.A

2. Shooting image adjustment software 　　Adjustments of Parts to be replaced

Gr/Gb compensation

ADJ (G filter)

Sensitivity

AFE Sensitivity ratio gain

Gr/Gb compensation

ADJ (R/B filter)

Pixel defect

Linearity

compensation

TFT TFT Shooting Upgrade Image PCB EEPROM view RISC angle EEPROM Flashram firmware Flashram

up

up

　Shutter unit

　Main FPC 1

　Main FPC 2

　AF PCB unit

　AF detector unit

TTL SPD unit

　DC/DC 1

　DC/DC 2 Penta-prism FPC unit Memory

○

compression PCB 　CF PCB

　I/F PCB

　Image PCB unit

○

○ ○

○

○

○

TFT PCB or TFT

○ ○

monitor

- Ａ52 ･

-

○

○

VBA10601-R.3665.A

Shooting Image Adjustment 1. Summary

When D2Hs shooting image-related, TFT display-related and listed parts on Page A52 are replaced, be sure to make an adjustment by the shooting image adjustment software for D2Hs (J65075). The details of its function and how to use this software are as follows:

2. Adjustment software function 　(1) "Gr/Gb compensation" adjustment (G filter) 　(2) "Sensitivity" adjustment 　(3) "AFE gain" adjustment 　(4) "Sensitivity ratio" adjustment 　(5) "Gr/Gb compensation" adjustment (R/B filter) 　(6) Pixel defect compensation 　(7) Linearity adjustment 　(8) "TFT view angle" adjustment 　(9) Shooting image PCB EEPROM flashram up 　(10) Factory setting 　(11) Reading of RISC version ※ When the memory compression PCB is replaced, perform only the followings: Flashram up of EEPROM value of the image PCB, Flashram up of EEPROM value of the TFT PCB, and Pixel defect compensation. ※ When the adjustments from (1) to (5) are made, calculate the sensitivity and sensitivity ratio reference values of (7) by using the reference body in advance, then perform the adjustments.

3. Hardware requirements 　OS： Widows98SE ，Windows2000 ，WindowsME ，WindowsXP 　　　　　　　Japanese or English OS PC： CPU　Pentium Ⅱ or more 　　　　　　Memory　128MB or more 　　　　　　USB1.1 or 2.0 　Screen size: 1024×768 pixels or more

4. How to set up 　Create any directory in the harddisc of PC, and copy the following files. 　・D2HsIMG.exe・・・・・・・・・Application file 　・STD.DAT・・・・・・・・・・Standard file 　・NkdPTP.dll・・・・・・・・・USB-communication application extension file for WinXP 　・NkdPTPDi.dll・・・・・・・・USB-communication application extension file for Win98SE,Win2K ， WinME 　※ Be sure to copy the above files in the same directory.

5. Install USB driver

* When this software is used, connect the camera via USB connection and install the USB driver. As for Windows2000, WindowsME, Windows98SE, install the USB driver by using NikonCapture. However, it is NOT necessary to install it in WindowsXP because the OS incorporates the driver.

*Before connecting the camera and PC, set USB to "PTP". - A53 ･　　

(Setup menu → USB → PTP) -

VBA10601-R.3665.A

6. How to use 　(1) Perform the D2HsIMG.exe to start up the main screen. (ref. Fig.1) 　(2) Select ENGLISH / JAPANESE in Language to display the expected menu.（ref. Fig.2）　(3) Click the desired button to start adjustments.

※ When the adjustments from 1. to 5. are made, calculate to get the “Sensitivity” and “Sensitivity ratio” reference values of (7) by using the reference body beforehand, then perform the adjustments. 　(4) Follow the instructions to be displayed on screen. 　(5) To complete the procedure, click "QUIT" button or "Close" button at the upper-right corner of the menu.

Fig. 1

Fig. 2 - A54 ･　　

-

VBA10601-R.3665.A

7. Required equipment and conditions

※ AC adapter EH-6, USB cable (mini B type), UC-E4 or UC-E5 are used for all adjustments so they are not specified in the list.

1

★ New established tool

Item Required equipment Gr/Gb compensation adjustment ・5100K color viewer　　J63070 (G filter)

Setting/Remarks Equivalent to luminance LV13

（ex-model viewer J63049 is also available.) ・Luminance meter BM-3000 　　J63068 Aperture F8 ・Tool lens（to fix aperture）　J61185 ・SP2 (G filter)　　J63086

2

Sensitivity adjustment

・CF card ・5100K color viewer　　J63070

8MB or more (The un- recorded one) Equivalent to luminance LV13

（ex-model viewer J63049 is also available.) ・Luminance meter BM-3000　　J63068

Aperture F8

・Tool lens（to fix aperture）　J61185

52 mm, Product diversion

・ND filter

7-step light depreciation

　（ND8 × 1 ＋ ND4 × 2） 3 AFE gain adjustment 4 Sensitivity ratio adjustment

・CF card Same as Sensitivity adjustment ・5100K color viewer　　J63070



Aperture F8

・Tool lens（to fix aperture）　J61185

No filter

・CF card 5 Gr/Gb compensation adjustment ・5100K color viewer　　J63070 (R/B filter)



Aperture F8

・Tool lens（to fix aperture）　J61185 ・SP3 (R filter)　　J63087 ・SP1 (B filter)　　J63085 6 Pixel defect compensation 7 Linearity adjustment

8MB or more (The un- recorded one) Environmental temperature approx. 20

・CF card Body cap or lens cap

・5100K colorviewer ・(Optical) transmissive grey scale 4:3, γ= 0.45

8 Sensitivity, sensitivity ratio

・Lens AF50/1.4D Same as Sensitivity adjustment

reference value calculation 9 TFT view angle adjustment

・D2H reference camera body None

10 Factory setting None 11 Shooting image PCB EEPROM None flashram up 12 TFT-PCB flashram up 13 Reading of RISC version

None None

- A55 ･　　

-

- 25℃ Equivalent to luminance LV13

No filter when sensitivity ratio reference value is calculated.

VBA10601-R.3665.A

8. Summary 　Each adjustment is summarized as follows: 　(1) Gr/Gb compensation adjustment (G filter) Camera is faced to the light-emitting box (color viewer) of LV13 equiv. with SP2 (G filter) being put between them, and adjustment is made so that the output difference between Gr and Gb in the center （300 ×300 pixels) can fall in the standard range. 　(2) Sensitivity adjustment Camera is faced to the color viewer of LV13 equiv. with ND filter (-7 step) being put between them, and adjustment is made by changing the ampgain so that G output can fall in the standard range. The gain value is adjusted so that the G output average value (Average of Gr/Gb) in the center (300×300 pixels) can reach the target output level (approx. 600LSB). The actual adjustment of the gain value is made only under the condition of ISO200 and ISO1600, and the medium sensitivity is calculated by the adjustment values of these 2 conditions. For target output level, G output average of sensitivity reference value (ISO200) is used, which was calculated by the reference body. 　(3) AFE gain adjustment Camera is faced to the color viewer of LV13 equiv. with ND filter (-7 step) being put between them, and adjustment is made by changing the ampgain so that the difference between G channel output and R/B channel output can fall in the standard range. Based on the output ratio among channels (average value of center 300×300 pixels) when shots are taken under the condition of ISO200,the gain is adjusted so that each output ratio under the condition of ISO400, ISO800 and ISO1600 becomes the same. 　(4) Sensitivity ratio adjustment Camera is faced to the color viewer of LV13 equiv., and the adjustment is made so that the R/G, B/G output becomes the same as the output ratio of the sensitivity ratio reference value that was calculated by the reference body. The adjustment is made only under the condition of ISO200, and the average value of the center (300 pixels × 300 pixels) is used. 　(5) Gr/Gb compensation adjustment (R/B filter) Camera is faced to the color viewer of LV13 equiv. with SP3 (R filter) or SP1 (B filter) being put between them, and the adjustment is made so that the difference between G output average of B-G line and the G output average of G-R line of the divided areas on the whole screen can fall in the standard range. 　(6) Pixel defect compensation Shots are taken on the dark surface. In case the pixel output is found to be beyond the standard value, the detected pixel coordinate is additionally written as the pixel defect compensation data. (7) Linearity adjustment The adjustment is made so that there is no color drift/shift when grey images are taken. 　

- A56 ･　　

-

VBA10601-R.3665.A

　 (8) "Sensitivity" and "Sensitivity ratio" reference values calculation 　　・Sensitivity reference value calculation The reference camera body is faced to the color viewer of LV13 equiv. with ND filter (-7 step) being put between them. Then, the G output average value of the center (300 pixels × 300 pixels) is stored in the STD.DAT file as the sensitivity reference value. 　　・Sensitivity ratio reference value calculation The reference camera body is faced to the color viewer of LV 13 equiv. (without filter). Then, the sensitivity ratio reference value GR and GB is calculated, based on the G/R/B output average of the center (300 pixels × 300 pixels), and they are stored in the STD.DAT file. It is necessary to calculate the reference values of "Sensitivity" and "Sensitivity ratio" in order to prevent the color temperature fluctuation caused by color viewer's changes over time from affecting the results of the shooting image adjustment. By using the reference body, calculate the reference values once in about every 3 months, when the fluorescent of the color viewer is replaced. (9) TFT view angle adjustment This is for adjusting the display position of TFT. The adjustment is made by NTSC video mode. (10) Facotry setting By reset the settings of camera, facotry settings are restored. 　(11) Image-PCB EEPROM flashram up EEPROM value of the image PCB is copied into the flash memory of the memory compression PCB (AK PCB). The flashram up is necessary when the memory compression PCB (AK PCB) is replaced.　 The shooting image-related adjustment values are stored in EEPROM of the image PCB. However, the camera does not directly access the image PCB EEPROM but it does read out the value, which is stored in the flash memory of the AK PCB of the memory compression PCB, into RAM to operate. Therefore, to reflect the adjustment value, it is necessary to copy the stored value of the image PCB EEPROM into the flash memory. ※ When the shooting image adjustments of each (1) - (5) are completed, the software automatically performs the flashram-up. 　(12) TFT PCB flashram up EEPROM value of the TFT PCB, as performed in the above image PCB, is copied into the flash memory. It is necessary to flashram up when the TFT PCB is replaced.　 ※ When the TFT view angle adjustment is completed, the software automatically performs the flashram-up. 　(13) Reading of RISC version RISC firmware version is displayed. The software displays the version that includes more than 2 places of decimals.

- A57 ･　　

-

VBA10601-R.3665.A

9. Procedure 9-1. Image PCB adjustment

　● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using the reference body beforehand, then perform the adjustments. (ref. 9-3.) 　● For the shooting image adjustment from (1) to (5), perform all of them in this order. The adjustments from (1) through (5) are all programmed to be executed in serial order. When (1) is completed, the software automatically goes on to the next adjustment. 　● In case adjustments are interrupted by NG, it is possible to continue the adjustments again after NG. As for adjustments that were ended with OK, the storage of adjustment values into EEPROM and the flashram-up are completed. 　　　Start adjustments 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Set the focus mode to M and the mode dial to S of the camera. 　・Turn the camera switch ON. 　・Set the color viewer luminance to LV13 equiv. 　(1) Gr/Gb compensation adjustment (G filter) 　・Click "Gr/Gb COMPENSATION ADJ (G FILTER)" on the menu. 　・Attach the tool lens (Aperture F8) and SP2 (G filter) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・The software automatically goes on to the next adjustment. 〔In case of NG〕・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF. （The reason for removing the AC adapter without turning the power switch OFF is, to prevent from storing what the software set during adjustments into the camera.）・Click the adjustment button again and repeat the adjustment. 　(2) Sensitivity adjustment 　・Click "SENSITIVITY ADJUSTMENT" of the main menu on screen. 　・Attach the tool lens (Aperture F8) and ND filter (ND 8× 1 ＋ ND 4 ×2）to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・The software automatically goes on to the next adjustment item. 　(3) AFE gain adjustment 　・Click "AFE GAIN ADJUSTMENT" of the main menu on screen. 　・Attach the tool lens (Aperture F8) and ND filter (ND 8× 1 ＋ ND 4 ×2）to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・The software automatically goes on to the next adjustment.　　　

- A58 ･　　

-

　(4) Sensitivity ratio adjustment 　・Click "SENSITIVITY ADJUSTMENT" of the main menu on screen. 　・Attach the tool lens (Aperture F8) to the camera (without filter). 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・The software automatically goes on to the next adjustment.

VBA10601-R.3665.A

　(5) Gr/Gb compensation adjustment (R/B filter) 　・Click "Gr/Gb COMPENSATION ADJ (R/B FILTER)" of the main menu on screen. 　・Attach the tool lens (Aperture F8) and SP3 (R filter) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, the next instruction is displayed. 　・Attach the tool lens (Aperture F8) and SP1 (B filter) to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, "OK" is displayed. 　Complete adjustments ・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF. （The reason for removing the AC adapter without turning the power switch OFF is, to prevent from storing what the software set during adjustments into the camera. If the power switch is turned OFF, initialize the camera setting by 2 button reset.） 9-2. Pixel defect compensation 　・Check the environmental temperature (approx. 20-25°C.). 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Set the focus mode to M and the mode dial to S of the camera. 　・Turn the camera switch ON. 　・Cap the camera with the body cap or lens cap to shield light from the mount. 　・Click "PIXEL DEFECT COMPENSATION" of the menu on screen. 　・When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses. 〔In case of NG〕 In case pixel defects are detected more than the standard value (512) or pixel defects are interconnected, the result becomes NG. Replace the image sensor unit. 　・Write the compensation value. When it is completed, "OK" is displayed. 　・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF.

- A59 ･　　

-

VBA10601-R.3665.A

9-3. Linearity adjustment

　(1) PC 　　・OS：Windows98SE or higher 　　・Memory: 512M or more recommended 　　・Monitor: Set the color setting to "32bit (TrueColor)". 　　　　　　　For software-creating reasons, tone jump appears in images with 16bit-or-less color setting. 　　　　　　　Checks are made on start-up to give warning except "32bit". 　(2) Camera setting 　　・Communication mode: PTP 　　・AE mode: M 　　・AF mode: M 　・Set the camera so that the grey chart stays within the viewfinder frame. 　・Displace the focus ring of the lens only slightly from its best focused position (to avoid moire). 　(3) Inspection and adjustment 　　・First, click on "CHECK" button to confirm the appearance on PC screen. 　　・Click "ADJUST" button to make the linearity adjustment. 　　・Click "INSPECTION" button to make the linearity inspection.

9-4. Sensitivity ratio reference value calculation 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Set the focus mode to M and the mode dial to S of the camera. 　・Turn the camera switch ON. 　・Set the color viewer luminance to LV13 equiv. 　・Select "SENSITIVITY, RATIO REFERENCE VALUE CALC" of the menu on screen. 　・The calculation of the sensitivity reference value starts. The message to set conditions is displayed. 　・Attach the tool lens (Aperture F8) and ND filter (ND 8× 1 ＋ ND 4 ×2）to the camera. 　・Get the camera closest to the center of the illuminated surface of the color viewer. 　・The adjustment starts. When it is completed, the software goes on to the sensitivity ratio reference value. ・The calculation of the sensitivity ratio reference value starts, and "SET TOOL LENS (f8)" is displayed. Remove ND filter. ・The adjustment starts. When it is completed, the sensitivity and sensitivity reference values are stored in the standard setting file (STD, DAT). ・After this procedure, when the shooting image adjustment is made, the sensitivity and sensitivity ratio that were calculated this time are used. ※ Calculate the sensitivity and sensitivity ratio reference values once in about every 3 months, when the fluorescent of the color viewer or tool lens (aperture F8) or ND filter (ND4) is replaced.

- A60 ･　　

-

VBA10601-R.3665.A

9-5. TFT view angle adjustment

　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Turn the camera switch ON. 　・Click "TFT VIEW ANGLE ADJUSTMENT" of the menu on screen. 　・When the adjustment starts, the NTSC adjustment is made and the frame is displayed on the LCD of the camera. 　・By clicking the "Left", or "Right", or "Up" or "Down" buttons on the window, move the frame from right to left or up and down to prevent from being shaded beyond the LCD area of the camera. 　・When "OK" is clicked, the software goes on to PAL adjustment. 　・Make an adjustment as performed in NTSC. 　・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF. 9-6. Factory setting 　Note: When the factory setting is performed, the USB mode is also automatically set to "MassStorage". However, the adjustment software is communicated in "PTP" mode, so if another communication is made, a communication error will occur. Therefore, perform the factory setting at the last. 9-7. Image-PCB EEPROM flashram up 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Turn the camera switch ON. 　・Click "SHOOTING IMAGE PCB EEPROM FLASHRAM UP" of the menu on screen. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF.

9-8. TFT PCB EEPROM flashram up 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Turn the camera switch ON. 　・Click "TFT PCB EEPROM FLASHRAM UP" of the menu on screen. 　・The adjustment starts. When it is completed, "OK" is displayed. 　・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF.

9-9. Reading of RISC version 　・Provide the power for the camera via AC adapter. 　・Connect the camera and PC via USB cable. 　・Turn the camera switch ON. 　・Click "READING OF RISC VERSION" of the menu on screen. 　・RISC version is displayed. 　・Remove the USB cable from the camera, and also remove the AC adapter without turning the power switch OFF. - A61 ･　　

-

VBA10601-R.3665.A

10. Procedure for upgrading RISC firmware: 　・ After preparing the CF card, copy the latest version (BD2S XXXX. BIN) into the root directory. 　・ Insert the CF card, and select "FIRMWARE VERSION" from the SETUP menu. 　・ Follow the instructions on screen for version upgrading. It takes approx. 3-4 minutes. 　・ Check the version of firmware by "RISC VERSION" of the shooting image adjustment software. 　Note: In case incorrect files are included in the CF card, the details for upgrading are not displayed even after selecting "FIRMWARE VERSION" from the SETUP menu.

- A62 ･　　

-

ｼﾝｸﾛﾀｰﾐﾅﾙ Sync terminal

W/Bｾﾝｻｰ W/B sensor

三つ葉FPC Triple operations FPC

測光ﾓｰﾄﾞ用ﾗﾝﾄﾞ Metering mode land

W/Bｾﾝｻｰ用ﾗﾝﾄﾞ W/B sensor land

ﾎｯﾄｼｭｰ Hot shoe

ｾﾙﾌLED Self timer LED ｾﾙﾌLED用基板 Self timer LED PCB

上カバーFPC① Top cover FPC①

VBA10601-R.3665.A

ｾﾞﾌﾞﾗ用ﾗﾝﾄﾞ Zebra land

バックライト Electric Luminescence

ｾﾞﾌﾞﾗｺﾈｸﾀｰ Zebra connector

液晶 LCD

Mode & 露出補正 & ﾚﾘ-ｽﾞSW Mode & exposure compensation & Release SW ﾚﾘｰｽﾞ切片FPC Release contact FPC

黄 Yellow

茶 Brown

前CMD(前ｺﾏﾝﾄﾞﾀﾞｲﾔﾙ)へ To front CMD(Front commond dial)

F-Fo基板 F-Fo PCB

黄 Yellow

LEDﾓｼﾞｭｰﾙ LED Module

上カバーFPC② Top cover FPC② Delete & MONITOR

ﾚﾝｽﾞ接点FPC Lens contact FPC

ﾚﾝｽﾞ接点ﾗﾝﾄﾞ Lens contact land

ﾌﾟﾚﾋﾞｭｰ＆ﾌｧﾝｸｼｮﾝFPC Preview & Function FPC

AF & AE LOCK

ﾒｲﾝFPC① Main FPC①

黄 Yellow

AFﾓﾀｰへ To AF Motor 黒Black

ﾒｲﾝFPC② Main FPC ②

実体配線図ＷＩＲＩＮＧ

後CMD(後ｺﾏﾝﾄﾞﾀﾞｲﾔﾙ)へ To Rear CMD(Rear commond dial)

Preview button

赤 Red

I基板制御用ｿﾚﾉｲﾄﾞＩPCB control solenoid

赤 Red 黒 Black

黒 Black )

ED

灰

(L

Gra

y

黒

om

ck

SCM切替基板 SCM chengeover PCB

-F

赤 Red

黒 Blac k

茶 Brown

ビデオ Video

DC-IN （ﾋｭ-ｽﾞも実装）

測光FPC Metering FPC

bo

In F内下LCD部組 (LED込） FD液晶用ﾗﾝﾄﾞ

DC-IN & ﾋﾞﾃﾞｵ基板 DC-IN & Video PCB

Slope sensor space

緑 Green

Slant sensor space

D LC

tt

Bla

ﾌﾟﾚﾋﾞｭｰﾎﾞﾀﾝ

ﾌｧﾝｸｼｮﾝﾎﾞﾀﾝ

Lands for AE element AE素子用ﾗﾝﾄﾞ In-F side LCD(LED) F内横LCD部組LED込）

Brown

ｼｬｯﾀｰFPC 黒Black Shutter FPC 茶Brown 赤Red 絞り用ﾌｫﾄｲﾝﾀﾗﾌﾟﾀ Aperture PI

ﾁｬｰｼﾞSW Cherge SW

黒 Black

DC/DC基板① DC/DC PCB①

Lands for FD LCD

ﾛｰﾊﾟｽﾌｨﾙﾀｰ(OLPF)

Blue

Black

ｼｰｹﾝｽﾓｰﾀｰ Sequence motor

傾斜ｾﾝｻｰｽﾍﾟｰｽ

Orange Function button

ﾚﾝｽﾞ着脱FPC Lens release FPC

Low pass filter

黄 Yellow ﾒｲﾝFPC① Main FPC① (旧MD基板）

撮像素子：LBcast Image sensor element:LBCAST

黒 Black

USB 2 mini B

黒B

Orange 橙

圧縮記録基板 MC PCB

lac

k

赤Re d

CFｶｰﾄﾞ基板 CF card PCB

TFT基板 TFT PCB

TFTﾊﾞｯｸﾗｲﾄ(LED)

USB基板 USB PCB

AFｴﾘｱｾﾚｸﾀ部 AF area selector

ﾌｫﾄﾘﾌﾚｸﾀ Photo reflector

ｼｬｯﾀｰ Shutter ﾄﾞｰﾑSW Dome SW

撮像基板 Image sensor unit

ﾎﾞﾀﾝ電池 Button battery

TFT

黒 ack Bl

赤 Red

d

黒 Black

ﾘｰﾄﾞ線ﾒｲﾝFPC②へ Lead wire to Main FPC② 黒 Black

ｱｸｾｽﾗﾝﾌﾟLED Access lamp LED

赤 Re

AFﾌｫﾄｲﾝﾀﾗﾌﾟﾀ AF photointerrupter

AFﾊﾟﾙｽFPC 赤Red AF pulse FPC

無線LAN用接点 Wireless LAN contact 電池接点基板

DC/DC基板② DC/DC PCB②

Battery contact PCB

赤Red

縦位置ﾚﾘｰｽﾞ用ﾗﾝﾄﾞ Vertical position release land 縦位置ﾚﾘｰｽﾞﾛｯｸ用ﾗﾝﾄﾞ Vertical position release lock land

黒 Black 黒 Black

縦位置前CMD用ﾗﾝﾄﾞ Vertical position front CMD land

AFﾓｰﾀｰ AF motor 黒 Black 橙 Oange

赤 Red

電池接点基板へ To Battery contact PCB

電池 (Li-ion EN-EL4） Battery (Li-ion EN-EL4)

縦位置FPC Vertical position FPC 縦位置AF-ON用ﾗﾝﾄﾞ Vertical position AF-ON land

AFエリアFPC AF area FPC

赤 Red

AFｴﾘｱﾓｰﾄﾞ部

スピーカ Speaker

背面液晶用LED Rear LCD LED

縦位置後CMD用ﾗﾝﾄﾞ Vertical position rear CMD land

AF area mode ﾏｲｸ Microphone

拡散板/ｾﾞﾌﾞﾗｺﾈｸﾀｰ拡散板/Zebra connector 背面液晶 Rear LCD

- Ｅ1 ･

-

VBA10601-R.3665.A

圧縮記録基板表 Memory compression PCB (Surface)

- E2・

-

VBA10601-R.3665.A

圧縮記録基板裏 Memory compression PCB (Reverse)

- E3・

-

Inspection standards / Tools list

VBA10601-R.3665.A

Contents [1]

Inspection standards　････････････････････････････････････････ R1 ～ R5

[2]

Tools list　･････････････････････････････････････････････････ T1 ～ T4

Inspection conditions 1. Environmental condition In case described that the temperature should be room temperature or unless otherwise noted: Temperature: 20±5℃ ; Humidity 65±20% 2. Standard voltage 　　11.1V ＋ 0.25Ω; 5A or more of power supply capacity 3. Battery 　　EN-EL4 (4 months or less elapsed after production） 4. Performance-guaranteed environment 　　Temperature: 0 - 40℃ ; Relative humidity: 85% or less

VBA10601-R.3665.A

Inspection standards Items External view Step (height difference)

Clearance

Size / Force Power dial Shutter release button

Shutter release button (vertically shooting)

Aperture lever

Criteria Between top cover and apron: 0.2 mm or less Other parts: 0.3 mm or less Moving parts: 0.5 mm or less

Remarks Visual check Digital micrometer

Between top cover and apron: 0.2 mm or less About the parts of card lid/card lid release-locking button lid Vertically: 0.6 mm or less Horizontally: 0.5 mm or less Between the parts of the top control panel window and the top cover: 0.45 mm or less Other parts: 0.3 mm or less Moving parts: 0.5 mm or less OFF-ON force: 350 ± 50g ON-illumination ON force: 480 ± 70g Protrusion: 3.8 ± 0.2 mm Halfway pressing force: 85 ± 15 g Halfway pressing stroke: 0.5 ± 0.1 mm Releasing force: 320 ± 50 g Releasing stroke: 0.3 ± 0.1 mm 　（Half-release pressing ON） Extra stroke after releasing button: 0.4 mm or more Half-releasing force: 235 ± 50 g Protrusion: 3.5 ± 0.15 mm Halfway pressing force: 85 ± 15 g Halfway pressing stroke: 0.5 ± 0.1 mm Releasing force: 270 ± 50 g Release stroke: 0.3 ± 0.1 mm 　（Half-release pressing ON） Extra stroke after releasing button: 0.4 mm or more Half-releasing force: 185 ± 50 g 3.4 height: 3.4 + 0.1 / - 0.05mm

Digital micrometer Tension gauge Visual check

Height gauge Collimator Main mirror tool Visual check

Main mirror

45 ゜ angle: Up-down ± 20' 　　　　　Right-left ± 25'　 Distortion: 6' or less Clearance for up-mirror in mirror box: None Play: 0.2 mm or less

Sub-mirror

49 ゜ angle: Up-down -5’ + 10’ - 25’ 　　　　　Right-left ±20’ Distortion: 8’ or less

Collimator Sub-mirror tool

∞ Infinity alignment

Screen ±45μm

Reference lens (J18010)

- R1 ･　　　 -

Items AF accuracy Yaw

Criteria Center：± 4mrad Others: ± 10mrad

Pitch

Center : ± 5mrad Others: ± 10mrad

Block Defocus

Side: 0 ± 60μm Others: 0 ± 50μm

AF-assist illuminator Lighting level

AE accuracy Exposure on image

VBA10601-R.3665.A Remarks PC Special tool Brightness box

When brightness is decreased, lighting starts in the range from EV5.2 to EV6.2.

Brightness box SB-80DX, SB-800

1/8000 - 1/4000：± 0.6EV (1/4000) - 1/2000：± 0.4EV (1/2000) - ：± 0.3EV Data spread: 0.3EV

Shutter speed tester (EF-8000)

Difference in AE mode: 0.4EV Difference in metering mode: 0.3EV Data spread in min. aperture/ continuous shooting: 0.5EV Shutter accuracy Speed accuracy

1/8000: ± 0.55EV 1/4000: ± 0.35EV 1/2000 ～ 30 seconds: ± 0.2EV

Data spread

1/8000：0.45EV or less 1/4000：0.35EV or less 1/2000 - 30 seconds: 0.25EV or less

Shutter curtain speed

Both front and rear curtains (16.6mm or less): approx. 2.6 ms or less

Shutter curtain bound

No bound

Synchronization

Time lag (16.6mm screen frame)：-0.05 - 0.15ms

- R2 ･　　　 -

Shutter speed tester (EF-8000)

VBA10601-R.3665.A ★ Newly prepared RJ

Items Viewfinder Inner LCD lower panel window position

Criteria Up-down position: 1.3 - 1.9a (a=window width) from the finder field frame Tilt: 1°or less

Inner LCD right panel window position

Right-left position: 0.6 - 1.2a (a=window width) from the finder field frame Tilt: 1°or less

Finder field frame

Shading, distortion: None Tilt: (based on bottom cover): 20’ or less Relative angle to image sensor: 30’or less

Field of viewfinder

In height and width: 100 + 0％ - 2％

Parallax (Center incoincident with the image sensor) Eye point Screen Screen misalignment

Sequence Release time lag

Remarks Visual check

Up-down: 0.15 mm or less Right-left: 0.2 mm or less

Distance to eyepiece protective glass: 19.9 ± 2 mm

Vernier caliper

Tilt:

Type E clear-matte focusing screen

30’ or less

AF-M: 45ms or less AF-C: 45ms or less Release at one push: 200ms or less Release when vibration reduction lens attached: 100ms or less Pre-flash release: 100ms or less

- R3 ･　　　 -

Oscilloscope; Constant-voltagepower source; Battery tool (J61210); EV9; Being in focus; Measure time from “Release” to “X-on”

VBA10601-R.3665.A Items Standby / consumed current

Operation time / consumption current accumulated

Criteria Main SW / OFF　　　　　　　　 200μA or less （Do NOT press all operation buttons.) Main SW / ON(Half-release timer OFF) 250μA or less Main SW / ON(Half-release timer ON) 350m A or less Main SW / ON(Illumination ON) 400mA or less Main SW / ON(TFT ON) 450mA or less

Lens scan 　AF50/1.4D　 Operation time: 850ms or less　　　Consumption current accumulated: 450mAsec or less 　AF28-70/3.3-4.5D　 Operation time: 1100ms or less 　　Consumption current accumulated: 550mAsec or less

Remarks Constant-voltage power source (5A or more) Battery tool (J61210) Ammeter AF50/1.4 Voltage: 11.1V　 0.25Ω Constant voltage power source (5A or more) Battery tool (J61210) Special tool Voltage: 11.1V　 0.25Ω

　AF80-200/2.8D　 Operation time: 1200ms or less 　　Consumption current accumulated: 700mAsec or less Preview 　 Operation time: 90ms or less 　 Consumption current accumulated: 80mAsec or less Release without film Operation time: 220ms or less 　 Consumption current accumulated: 200mAsec Rush current

During shooting operation: 6.2A or less

Constant voltage power source (5A or more) Battery tool (J61210) Special tool Oscilloscope

Clock accuracy

Difference par month: ±30 seconds (20℃）

Wave clock

BC level

Level 5:　5 lights up　 Charge remaining: 70 ～ 100% Level 4:　4 lights up　 Charge remaining: 50 ～ 69% Level 3:　3 lights up　 Charge remaining: 35 ～ 49% Level 2:　2 lights up　 Charge remaining: 20 ～ 34% Level 1:　1 light up　 Charge remaining: 1 ～ 19% Level 0:　1 light blinking　Charge remaining: 0%

Check the level in the LCD control panel on top of camera or TFT battery information

When special Li-ion is used: 1 and a half hours or more

Clock Remote wire

Bulb battery life

- R4 ･　　　 -

Communicationcapable battery tool

VBA10601-R.3665.A

Items Battery life

Criteria

Remarks

General mode 　Room temperature: 520 frames or more 　0℃ : 480 frames or more 　-10℃ :　300 frames or more AF-S24-120/3.5-5.6 VR off, AF-C, Film advance S, M1/250 F5.6, AF scanning with 1 back-and-forth movement → Half-pressing 6 seconds → Shutter release once → TFT monitor 2 seconds → Half-release timer OFF (Repeat)

Professional mode 　Room temperature: 2000 frames or more 　0℃ : 1600 frames or more 　-10 ﾟＣ :　1200 frames or more AF-S70-200/2.8 VR off, AF-C, Film advance Ch, M1/250 F5.6, AF scanning with 3 back-and-forth movement → Half-pressing 3 seconds → 6 shutter releases → TFT monitor 5 seconds → Half-release timer OFF (Repeat)

- R5 ･　　　 -

VBA10601-R.3665.A

工具編 TOOLS １．カメラ部

★：NEW TOOL

FOR CAMERA

RJ 番号

名称

備考

RJ No.

NAME OF TOOL

OTHERS

J18356

45 度出し工具ミラー（D2H） MIRROR TOOL (D2H)

FOR D2H, D2X

J18352

サブミラー位置出し工具 SUB MIRROR INSPECTION TOOL(D2H)

FOR D2H, D2X

J61199

D100 AE 受光部アダプター D100 LIGHT RECEIVE ADAPTER

FOR D100, D2H, D2X

工具設定なし RJNo.is not available

鉛フリーはんだコテ LEAD FREE SOLDERING IRON

J5400

鉛フリー糸はんだ RMA02(M705) 0.5MMX500G ECO SOLDER RMA02(M705) 0.5MMX500G


へクスキー（φ 1.5mm） HEX.KEY WRENCH ( φ 1.5mm)

J15408

D2H 用無限合致点検スクリーン INFINITY FOCUS CHECK SCREEN FOR D2H

FOR D2H, D2X

T93004

SI 表示板外し工具 SI PLATE REMOVE TOOL

FOR D1

J15406

1005 センサー位置出し工具（Ｄ２Ｈ） 1005 SENSER POSITIONING TOOL (D2H)

FOR D2H, D2X

J18382

D2Hs 調整用 FD IBM 3.5 ADJ.FD FOR D2Hs (IBM 3.5)

工具設定なし

ＡＣアダプター（ＥＨ -6） AC ADPUTER (EH-6)

FOR D2H, D2X

J15407

マルチカム 2000 ＡＦチャート Multi CAM 2000 AF CHART

FOR D2H, D2X

J15404

視差点検調整用チャート PARALLAX CHART

FOR D2H, F6, D2X

工具設定なし

高周波タイプ蛍光灯器具

TI-03045 を参照

RJNo.is not

ILLUMINATION BOX FOR AF ADJUSTMENT

★

RJNo.is not available

REF. TIE-03045

available

- Ｔ1 ･

-

VBA10601-R.3665.A ★：NEW TOOL RJ 番号

名称

備考

RJ No.

NAME OF TOOL

OTHERS

J15259

AF 調整工具台 AF ADJUSTING TOOL

J15409

J15407 用チャートボード CHART BOARD FOR J15407

J15280

ﾚﾝｽﾞﾎﾙﾀﾞｰ LENS HOLDER FOR F4

J18001-1

ﾎﾞﾃﾞｨｰﾊﾞｯｸ出し工具 BODY BACK FOCUS GAUGE

J18004

絞りﾚﾊﾞｰ位置測定工具 APERTURE LEVER POSITIONING GAU

J18010

基準ﾚﾝｽﾞ 50/1.8 STANDARD LENS 50/1.8

J18037

ﾐﾗ -45 ﾟ点検工具 MIRROR 45 DEG. INSPECTION TOOL

J18230

YAW PITCH 工具 YAW PITCH TOOL

FOR F5, F100, F90, F90X, D2H, D2X

J18266

AF 調整ﾚﾝｽﾞ (1m) AF ADJUSTMENT LENS (1m)

FOR F5, F100, D2H, D2X

J18267

測光用 AF50/1.4 D AE ADJUSTMENT LENS AF 50/1.4 D

J19001

調整用ｺﾘﾒ - ﾀ - 600mm COLLIMATOR F=600MM

J19004-1

ｲﾝｼﾞｹﾞ - ﾀ - 及びｽﾀﾝﾄﾞ DIAL INDICATOR & STAND

J19042D

像面露光量測定アダプター (EF8000,EF-1 両用） EXP.VALUE MEASURING ADAPTER (For EF8000,EF-1)

J19042E

Ｔ秒時測定アダプター -(APS)(EF8000 用） T.V. MEASURING ADAPTER (APS) (For EF8000)

J19110

小型ﾊﾞｯｸ出しｺﾘﾒｰﾀｰ (CE 対応品 ) BACK FOCUS COLLIMATOR 24LT-2DTS(CE)

- Ｔ2 ･

FOR D2H, D2X

-

VBA10601-R.3665.A ★：NEW TOOL RJ 番号

名称

備考

RJ No.

NAME OF TOOL

OTHERS

J9001-5N

安定化電源５Ａ DC REGULATED POWER SUPPLY 5A

J19109

MC-31（接続コード） MC-31 (CONNECTING CORD)

供給できず RJNo.is not available

ｼｬｯﾀ - ﾃｽﾀ - EF-8000 SHUTTER TESTER EF-8000

共立電機製 KYORITSU ELECTRIC

J19123

ｼｬｯﾀ - ﾃｽﾀ - EF-1(CE) SHUTTER TESTER EF-1(CE)

共立電機製 KYORITSU ELECTRIC

J19123E

Ｔ秒時測定アダプター -(APS)(EF-1 用） T.V. MEASURING ADAPTER (APS) (For EF-1)


パソコン（シリアルポート、ＵＳＢ必需、Windows98SE 以降） PC (serial port & USB are required, Windows98SE or later)


デジタルマルチメーター DIGITAL METER

J61210

D2X 電池工具 D2X BATTERY TOOL

OS-30MF

ドライサ－フ　ＯＳ－３０ＭＦ DRY SERF OS-30MF(OIL BARRIER)

G92KA

フロイル　Ｇ９２ＫＡ FLOIL (G92KA)

EDB0011

ネシ゛ロック（赤）1401C SCREW LOCK 1401C

C-8008B

セメダイン　８００８（黒） CEMEDAIN 8008(BLACK)

NK-A7420

ﾛｹﾞﾈｽﾄﾗﾑﾀﾞ SPECIAL GREASE

EBB0061

スクアグリ－スＧ７１００ SQUA GREASE L-2 (G7100)

L-271

ﾛｯｸﾀｲﾄ #271 LOCTITE #271

MZ-800S

ドライサ－フ　ＭＺ－８００Ｓ DRY SURF MZ-800S

SC608Z

ｿﾆｰﾎﾞﾝﾄﾞ　SC608Z SONY BOND SC608Z

EDZ4113

ボンド　Ｇ１０３ BONDO G103

- Ｔ3 ･

FOR D2H, D2X

-

VBA10601-R.3665.A ２．撮像関係点検・調整　SHOOTING IMAGE ADJUSTMENT AND TFT ADJUSTMENT

★：NEW TOOL

RJ 番号

名称

備考

RJ No.

NAME OF TOOL

OTHERS

J61185

撮像関係調整用レンズ D1 STANDARD LENS

J18191

ＮＤフィルタ－８Ｘ ND FILTER 8X

J18358

ＮＤフィルタ－ 4 Ｘ ND FILTER 4X

２枚使用 It uses by two pieces

J63070

カラービュワー COLLOR VIEWER

J63049 でも代用可 It is possible to substitute J63049.

J63054

グレイスケールチャート GREY SCALE CHART

J63068

輝度計（ＢＭ 3000） LUMINANCE METER BM-3000

J65075

D2Hs 撮像調整ｿﾌﾄ (J/E) D2Hs IMAGE SENSOR ADJ. SOFT(J/E)

J63085

ﾌｨﾙﾀｰ SP1 (75X75MM) FILTER SP1 (75X75MM)

J63086


J63087


供給できず RJNo.is not available

CF カード（8 ＭＢ以上） COMPACT FLAFH CARD

★

- Ｔ4 ･

-

Nikon D2Hs Repair_Manual

Recommend Documents