National Plumbing Code of Trinidad and TobagoFull description
Full description
civil code of the philippines
Full description
Full description
Full description
National Structural Code of the Philippines 2010 6th Edition
6/16/2015
National Plumbing Code of the Philippines | Architecture is fun!
National Plumbing Code of the Philippines Air Gap An air gap in a water supply system, is the unobstructed vertical distance through the free atmosphere between the lowest opening from any pipe or faucet supplying water to a tank, plumbing fixture , or other device and the flood level rim of the receptacle. Back Flow is the flow of water, or other liquid mixture or substances into the distributing pipes of a potable supply of water from any source, other than its intended source. Back Siphonage refers to the back flow of used contaminated or polluted water from a plumbing fixture or vessel into a water supply pipe due to negative pressure in such a pipe. Battery of Fixture refers to any group of two or more similar adjacent fixtures which discharges into a common horizontal waste pipe or soil branch. Bibb is synonymous with faucet,cock, tap, plug. Branch is any part of piping system other than the main riser or stack. Caulking is plugging an opening with an oakum, lead or other materials, that are pounded into place or opening. Common Vent is a drain from two or three fixture connected to a single trap. It is also called a dual vent. Developed Length The length along the center of the pipe and fitting. Diameter diameter of a pipe or tube refers to the nominal internal diameter (ID) of such pipe, except brass and copper tube where the terms refers to the outside diameter (OD) of the pipe. Dry Vent a vent that does not carry water. Effective Opening is the minimum cross sectional area at the point of water supply discharge, measured or expressed in terms of diameter of a circle. If the opening is not a circle ,the diameter of a circle that is equivalent the cross sectional area. Fixture Unitsis a quantity in terms of which the load producing effects on the plumbing system of different kinds of plumbing fixtures are expressed on some arbitrarily chosen scale. Flash Valve is a device located at the bottom of the tank for flushing water closets and similar fixtures. Flushometer Valve is a device which discharges a predetermined quantity of water to the fixture for flushing purposes activated by direct water pressure. Grade is the slope or fall of pipe in reference to a fraction of an inch per foot length of a pipe. Invert is the lowest portion of the inside of any pipe or conduit that is not a vertical. Lateral is a secondary pipe. http://reviewarchitecture2014.blogspot.com/2014/03/nationalplumbingcodeofphilippines.html
1/5
6/16/2015
National Plumbing Code of the Philippines | Architecture is fun!
Main Sewer is a sewer line or system directly controlled by public authority. Relief Vent a relief vent's primary function is to provide circulation of air between drainage and vent systems. Riser is a water supply pipe which extend vertically one full storey or more to convey water to branches or fixtures. Roughing in is the installation of all parts of plumbing system which can be completed prior to the installation of fixtures. This include drainage, water supply, vent, piping and the necessary fixture supports. Siamese connection is a Y connection used on fire lines so that two lines of hose maybe connected to a hydrant or to the same nozzle. Soil pipe is any pipe that conveys the discharge of water closets or fixtures having similar function, with or without the discharge from other fixtures, to the building drains (house drain) or building sewer (house sewer). Stack Vent is the extension of a soil or waste stack above the highest horizontal drain connected to the stack. Sump a pit or receptacle at low point to which the liquid waste are drained. Trap is a fitting or device so designed as to provide when properly vented a liquid seal that will prevent the back passage of air without materially affecting the flow of sewage through it. Vent Stackis a vertical pipe installed primarily for the purpose of providing circulation of air to different parts of the drainage system. Waste Pipe is a pipe that conveys liquid waste from fixture that is free of fecal matter.
References: The National Plumbing Code of the Philippines, Plumbing
National Plumbing Code of the Philippines | Architecture is fun!
NATIONAL PLUMBING CODE OF THE PHILIPPINES 92 Questions
NATIONAL PLUMBING CODE
Start
NATIONAL PLUMBING CODE OF THE PHILIPPINES [http://www.proprofs.com/quizschool/story.php?title=nationalplumbingcodephilippines] » Create A Quiz [http://www.proprofs.com/quizschool/]
National Plumbing Code of the Philippines | Architecture is fun!
National Plumbing Code of the Philippines 10 Questions
National Plumbing Code of the Philippines Definition of Terms
Start
National Plumbing Code of the Philippines [http://www.proprofs.com/quizschool/story.php?title=NjQxNDU5WDLS] » Quiz maker software [http://www.proprofs.com/quizschool/]
Posted 20th March 2014 by belle arch Labels: drain, national plumbing code, philippines, pipe, vent 0 Add a comment
