NA to BS en 1993 1 5 2006- UK National Annex to Eurocode 3- Design of Steel Structures. Plated Structural Elements

NA to BS EN 1993-1-5:2006

NATIONAL ANNEX

UK National Annex to Eurocode 3: Design of steel structures – I S B

Part 1-5: Plated structural elements ICS 91.010.30; 91.080.10

© , y p o C d e l l o r t n o c n U , 8 0 0 2 / 0 1 / 3 2 , d t L n a r o M n o s l i H : y p o c d e s n e c i L

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

NA to BS EN 1993-1-5:2006

Publishing and copyright information The BSI copyright notice displayed in this document indicates when the document was last issued. © BSI 2008 ISBN 978 0 580 54964 9 The following BSI references relate to the work on this standard: Committee reference B/525/10 Draft for comment 07/30128103 DC

Publication history First published May 2008

Amendments issued since publication Amd. no.

I S B © , y p o C d e l l o r t n o c n U , 8 0 0 2 / 0 1 / 3 2 , d t L n a r o M n o s l i H : y p o c d e s n e c i L

Date

Text affected

NA to BS EN 1993-1-5:2006

Contents Introduction 1 NA.1 Scope 1 NA.2 Nationally Determined Parameters 2 NA.3 References to non-contradictory complementary information 4

Bibliography 5


Summary of pages

This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 5 and a back cover. © BSI 2008

•

i

NA to BS EN 1993-1-5:2006


ii • © BSI 2008

This page deliberately left blank

NA to BS EN 1993-1-5:2006

National Annex (informative) to BS EN 1993-1-5:2006, Eurocode 3 – Design of steel structures – Part 1-5: Plated structural elements Introduction This National Annex has been prepared by BSI Subcommittee B/525/10, Bridges, in consultation with B/525/31, Structural use of steel.

NA.1 Scope This National Annex gives: a) I S B © , y p o C d e l l o r t n o c n U , 8 0 0 2 / 0 1 / 3 2 , d t L n a r o M

the UK decisions for the Nationally Determined Parameters described in the following subclauses of BS EN 1993-1-5:2006: •

2.2(5)

•

3.3(1)

•

4.3(6)

•

5.1(2)

•

6.4(2)

•

8(2)

•

9.1(1)

•

9.2.1(9)

•

10(1)

•

10(5)

•

C.2(1)

•

C.5(2)

•

C.8(1)

•

C.9(3)

•

D.2.2(2)

b) References to non-contradictory complementary information (see NA.3).

n o s l i H : y p o c d e s n e c i L

© BSI 2008

•

1

NA to BS EN 1993-1-5:2006

NA.2 Nationally Determined Parameters NA.2.1

Effective width models for global analysis [BS EN 1993-1-5:2006, 2.2( 5)] The recommended value of effective width parameter ρ lim should be used.

NA.2.2

Shear lag at the ultimate limit state [BS EN 1993-1-5:2006, 3.3( 1)] The recommended method in NOTE 3 should be used.

NA.2.3

Effective cross section [BS EN 1993-1-5:2006, 4.3( 6)] The recommended value of ϕ h should be used.

NA.2.4

I S B

Basis [BS EN 1993-1-5:2006, 5.1( 2)] The value of η should be taken as 1,0 for all steels.

©

NA.2.5

, y p o C

NA.2.5.1 Equation (6.6) should be used for patch loading Types (a) and (c) from Figure 6.1 for beams with longitudinal stiffeners. At locations beyond the limits for which equation (6.6) in 6.4(2) is valid, the treatment of such patch loading will be as for an unstiffened web.

d e l l o r t n o c n U

NA.2.5.2 Equation (6.6) should not be used for patch loading types (b) from Figure 6.1 for beams with longitudinal stiffeners. Patch loading Type (b) from Figure 6.1 may be treated as for an unstiffened web or may be subject to a special buckling analysis.

, 8 0 0 2 / 0 1 / 3 2

NA.2.6

Flange induced buckling [BS EN 1993-1-5:2006, 8( 2)] NA.2.6.1 The design for flange induced buckling should take account of the possible collapse of the web due to radial forces from a flange in compression or tension curved in elevation, whether or no t a beam as a whole is curved.

, d t L

NA.2.6.2 For nominally horizontal flanges, Clause 8(2) may be applied, but the adequacy of the web should be checked using the same analysis as for beams with flanges curved in elevation with a radius of curvature corresponding to an out-of-flatness equal to the span/625.

n a r o M n o s l i H : y p o c d e s n e c i L

Reduction factor kF for effective length for resistance [BS EN 1993-1-5:2006, 6.4( 2)]

NA.2.6.3 The adequacy of the web with curved flanges should be verified by analysis of the buckling strength of the web, whether stiffened or not, under radial forces induced by the flanges and associated webs in addition to any coincident global shear and longitudinal forces. The adequacy of the web should also be verified by use of the rules in Clause 6 in conjunction with 7.2(1).

2 • © BSI 2008

NA to BS EN 1993-1-5:2006 NA.2.6.4 For beams with only the compression flange curved the buckling coefficients, Type (a) in Figure 6.1 should be used. For beams with both flanges curved, the Type (b) coefficients should be used. For such a method of verification, γ Ml should be taken as 2,0 in deriving η 2.

NA.2.7

Stiffeners and detailing [BS EN 1993-1-5:2006, 9.1( 1)] NA.2.7.1 Where the web of a beam is subjected to a net compressive force, whether due to externally applied compressive force or due to the flexural neutral axis not being at the mid-height of the web, the effect of the net compressive force should be considered in the design of rigid transverse stiffeners resisting shear. NA.2.7.2 When applying 9.3.3(3), the design force in the NOTE should not be used. Instead, intermediate rigid stiffeners should be designed for an axial force, ρ Ed, acting in the mid-plane of the web in addition to any externally applied loads, where: ρ Ed

−

hw t × 0,8τ 1 −

⎡ ⎢VEd ⎢⎣

−

hw t × 0,8τ cr 1 −

I S B ©

ρ Ed

, y p o C

for a . h w

σ x,Ed 0,8σ cr,x

⎤ a for a < h w ⎥ ⎥⎦ hw

τ cr is the elastic critical shear buckling stress determined in accordan ce with 5.3; σ cr,x is the elastic critical plate buckling stress for direct stress determined in accordance with 4.4 or 4.5 for sub-panel buckling and overall stiffened plate buckling respectively; and σ x,Ed is the greatest longitudinal compressive stress in the web panel under consideration.

, 8 0 0 2 / 0 1 / 3 2

σ x,Ed is taken as positive when compressive and should not be taken as being greater than 0,8σ cr,x. NA.2.7.3 When applying 9.2.1, σ cr,c and σ cr,p should generally be calculated for a panel length of a1 + a2 with w0 taken as the lesser of b /300, a1 /300 and a2 /300. However, to safeguard against a mode of buckling with adjacent transverse stiffeners bowing in alternate directions, 9.2.1 should also be applied with σ cr,c and σ cr,p calculated for a panel length of 0,5 (a1 + a2). In this case, w 0 should be taken as the lesser of b /150, a1 /150 and a2 /150.

, d t L n a r o M

d e s n e c i L

0,8σ cr,x

where:


n o s l i H : y p o c

=

σ x,Ed

VEd

=

For panels with longitudinal stiffeners, the ratio Ö cr,c / Öcr,p should be taken to be equal to 1,0 unless an alternative value can be justified by calculations which can also be supported by either test evidence or non-linear analysis.

NA.2.8

Minimum requirements for transverse stiffeners [BS EN 1993-1-5:2006, 9.2.1( 9)] The value of θ should be taken as 2,0.

© BSI 2008

•

3

NA to BS EN 1993-1-5:2006

NA.2.9

Reduced stress method [BS EN 1993-1-5:2006, 10( 1)] There are no limits of application to the methods.

NA.2.10

Reduced stress method [BS EN 1993-1-5:2006, 10( 5)] For panels with tension and compression, equations (10.4) and (10.5) should be applied only to the compressive parts.

NA.2.11

Use [BS EN 1993-1-5:2006, C.2( 1)] Conditions for the use of FEM analysis in design should be specified for the particular project.

NA.2.12

Use of imperfections [BS EN 1993-1-5:2006, C.5( 2)] The recommended approach should be adopted.

I S B

NA.2.13

© , y p o C

Limit state criteria [BS EN 1993-1-5:2006, C.8( 1)] The limit to principal strain for regions subjected to tensile stresses should be 5%.


NA.2.14

Partial factors [BS EN 1993-1-5:2006, C.9( 3)] NA.2.14.1 For bridges, γ M1 and γ M2 as specified in the National Annex to BS EN 1993-2 should be used. NA.2.14.2 For buildings, γ M1 and γ M2 as specified in the National Annex to BS EN 1993-1-1 should be used.

, 8 0 0 2 / 0 1 / 3 2

NA.2.15

Shear resistance [BS EN 1993-1-5:2006, D.2.2(2)] No additional information is provided.

, d t L

NA.3 References to non-contradictory complementary information

n a r o M

PD 6695-2, Recommendations for the design of bridges to BS EN 19931).

n o s l i H : y p o c d e s n e c i L

1)

4 • © BSI 2008

In preparation.

NA to BS EN 1993-1-5:2006

Bibliography For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NA to BS EN 1993-1-1, UK National Annex to Eurocode 3: Design of steel structures – Part 1-1: General rules and rules for buildings NA to BS EN 1993-1-2, UK National Annex to Eurocode 3: Design of steel structures – Part 2: Steel bridges PD 6695-2, Recommendations for the design of bridges to BS EN 19932)


2)

In preparation.

© BSI 2008

•

5

NA to BS EN 1993-1-5:2006

BSI – British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.

Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.

Buying standards

©

Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also available from the BSI website at http://www.bsi-global.com.

, y p o C

In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.

I S B


Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected]. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: [email protected].

, 8 0 0 2 / 0 1 / 3 2

Information regarding online access to British Standards via British Standards Online can be found at http://www.bsi-global.com/bsonline. Further information about BSI is available on the BSI website at http://www.bsi-global.com.

, d t L

Copyright

n a r o M n o s l i H : y p o c d e s n e c i L

Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.

389 Chiswick High Road London W4 4AL

Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: [email protected].

NA to BS en 1993 1 5 2006- UK National Annex to Eurocode 3- Design of Steel Structures. Plated Structural Elements

Recommend Documents