FESMED II 4052 FESMED IV 4054 Symbols Device symbols
FESMED II 4052 FESMED IV 4054 Packaging symbols Caution fragile. Handle with care
Device is off Keep in a dry place
Device is on This symbol indicates the device causes physiological effects and that the user should check the user’s manual before using it. BF type applied part
IPX0
Not protected from harmful water penetration Class II equipment Manufacturer Identification Product Manufacture Date Product Serial Number European Representative CE marking and identification of the no tified agency
MU_4052_4054_ENG_Rev:02_092009
This side up. This symbol indicates the right transport position Maximum piling. Indicates the maximum number of boxes that can be piled. The quantity is indicated in the middle square. Minimum and maximum temperature limits for transportation and storage.
ATTENTION 1. Read, understand and practice the operation and precaution instructions. Know the limitations and dangers associated with use of any electrical stimulation device. 2. Do not expose the device to direct sunlight radiated from a heat radiator, excessive quantities of dust, humidity, vibrations and mechanical shocks. 3. In the case of liquid liquid infiltration, disconnect the device from the power network and contact the Authorized Technical Assistance. 4. Before administering any treatment on a patient, you must become acquainted with the operational procedures for each treatment modality available, as well as the indications, contraindications, warnings and precautions. Consult other resources to obtain further information on the application of electrotherapy.
MU_4052_4054_ENG_Rev:02_092009
5
FESMED II 4052 FESMED IV 4054 Electrical Installation/Connection Installation/Connection For a perfect device operation, we suggest electrical installations according to the following rules: Brazil:
Remove the fuse compartment cover with the help of a screwdriver (insert the tip into the fuse compartment groove, press down slightly and rotate counterclockwise).
Display Language FESMED offers display configuration in three possible idioms:
NBR 5410/1990 – Low-voltage electrical installations; • NBR13534/1995 – Electrical installations at medical locations Safety requirements. Other Countries: • IEC 60364-7-7 (10/2002) – E Electrical lectrical Installations – medical locations; • Or another related norm applicable in the utilization country. •
•
FESMED II 4052 FESMED IV 4054
Portuguese English
Spanish
If you want to change the current language, follow the steps below: 1. 2.
Connect one end of the power cable to the the three-pole socket on the rear panel and the other end to the wall outlet.
Connect FESMED power cable to the utility power supply. Turn on the device – the unit will perform a display test and the screen below will appear:
SN.: 00001
Figure 01 •
Your equipment uses switched power supply and operates at any volt supply between 100 and 240VCA, 50 or 60Hz.
•
In case the protection fuse is blown, replace only with another one of the indicated rating:
FESMED 405X Rev.: X.Y
3.
After that, press and hold the following key:
4. 5.
6.
After a double beep is heard, release Menu key. key. The display will show the language options: ENGLISH PORTUGUESE ESPANOL Select the idiom using the arrow keys:
7.
Press the following key:
Fuses should be 1.0A 250V 20AG
MU_4052_4054_ENG_Rev:02_092009
MU_4052_4054_ENG_Rev:02_092009
FESMED II 4052 FESMED IV 4054 8.
The unit will exit the language selection mode, and the Main Menu will be displayed.
FESMED II 4052 FESMED IV 4054 Control Functions NEXT FIELD
Controls Fesmed II 4052
INCREASES SETTING
DECREASES SETTING
PREVIOUS FIELD
Fesmed IV 4054
Intensity control for channels 1 and 2 of Fesmed II 4052
Intensity control for channels 1, 2, 3 and 4 of Fesmed IV 4054
