Algunas reparaciones de tv LCD comentadasDescripción completa
Algunas reparaciones de tv LCD comentadas
Descrição: Algunas reparaciones de tv LCD comentadas
Descrição completa
Descripción completa
WIN8 click dr si TRAGI IN JOS apare all apps; Oct 23-24, 2006 Service Seminar CS Promotion Center Panasonic AVC Networks Company Contents 1. LCD Line-up for Y2006 2. Chassis Structure…Description complète
Descripción completa
LCD TV infoFull description
WIN8 click dr si TRAGI IN JOS apare all apps; Oct 23-24, 2006 Service Seminar CS Promotion Center Panasonic AVC Networks Company Contents 1. LCD Line-up for Y2006 2. Chassis Structure…Full description
Guia de reparacion de TV LCDFull description
Descripción: Guia de reparacion de TV LCD
Descripción completa
Capture 9 SERVICE MODE SERVICE ICE MODE 9-1. ENTERING SERV
1 ) Press
but t on on c e o n
2 ) Press
R e m o t e C on t r ol .
b u t t o n a g a i n an d
3 ) W h i l e pr es s i ng t he
keep pressing.
b u t t o n,
press MENU button on TV set.
or Sound Mute (Service mode display) 9-2.
DISPLAYING DISPLA YING THE ADJUSTMENT MENU
1) Pre Press ss MENU MENU bu butto tton n on TV TV.. Service mode
A d j u s t m en t m od e Press Press
9-3. KEY FUNCTION IN THE SERVICE SERVICE MODE
The following key entry during display of adjustment menu provides special functions. Test signal selection : Selection of of th the adjustment ititems : Change of the data value : Adju jus stment menu mode ON/OFF : Initialization of the memory : Reset the count of operating protect circuit to “00”: “RCUT” selection : “GCUT” selection : “BCUT” selection : “SCNT” selection : “COLP” selection : “TNTC” selection : Automatic A/D Adjustment(PC, Component) : Self diagnostic display ON/OFF :
a button (on Remote) Channel s / t (on TV or Remote) Volume ; +/– (on TV or Remote)
MENU button (on TV) CALL + Channel Channel button button on TV (s) CALL + Channel button on TV (t) 1 button 2 button 3 button 4 button Color thickness correction 5 button note: Displayed differently as shown shown below, below, de6 button pending on the setting of the receiving color 7 b ut t on system. 9 bu t t on COLP (P ( PAL) COLC (NTSC) COLS (SECAM)
CAUTION : Never try to perform initialization unless you have changed the memory IC.
- 9-1 -
9-4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) 9-5. ADJUSTING THE DATA
1) Pressing of VOLUME ; +/– button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item. 9-6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once. ■
INITIALIZATION OF MEMORY DATA
After replacing EEPROM IC, the following initialization is required. 1. Enter the service mode, then select any register item. 2. Press and hold the CALL button on the Remote, then press the CHANNELs button on theTV. The initialization of EEPROM IC has been complated. 3. Check the picture carefully. If necessary, adjust any adjustment item above. Perform “Auto tune” on the owner’s manual. CAUTION: Never attempt to initialize the data unless EEPROM IC has been replaced. 9-7. TEST SIGNAL SELECTION
1) Every pressing of a button on the Remote Control changes the built-in test patterns on screen as described below in SERVICE MODE. Signal off
R
All White
G
B
Signals
All Black
• Red raster • Green raster • Blue raster • All Black • All White
- 9-2 -
Picture
9-8.
1)
SELF DIAGNOSTIC FUNCTION
Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s is executed properly.
2)
During diagnosis, the following displays are shown.
WL56_EU_0100
32WL56P
Firmware :
Version information of microprocessor In case of file name : WL56_EU and Version : 0100 indicates[WL56_EU_0100]. Time : Total hour of turn the TV on. (Unit : H) Power : Operation number of protecting circuit ----"000" is normal.
When indication is other than "000", overcurrent apt to flow, and circuit parts may possibly be damaged. Bus line : --"OK" is normal
"SCL-GND"(Red indication) : SCL-GND short circuit "SDA-GND"(Red indication) : SDA-GND short circuit "SCL-SDA"(Red indication) : SCL-SDA short circuit Bus cont : --- "OK" is normal.
NG is abnormal(Red indication). When type name of semiconductor indicates. Block
UV : TV reception mode V1 : VIDEO 1 input mode (
1)
V2 : VIDEO 2 input mode (
2)
V3 : VIDEO 3 input mode (
3)
V4 : VIDEO 4 input mode (
HDMI)
8 digit : CD number Model name (7 digit)
- 9-3 -
9-9.
1)
VERSION CHECK MODE
Press “9” button twice on Remote Control during display of adjustment menu in the service mode. The version of main MPU will begin to check.
2)
During Version Check, the following displays are shown.
(
MAIN MPU :
Version information of microprocessor In case of file name : WL56_EU, Version 0100 for Code Program Version and (E16) for OSD Version indicates [WL56_EU_0100(E16)] EEPROM :
Version information of EEPROM : Display 1 byte dat a. SUB MPU :
Version information of SUB MPU : Display 1 byte data. OPTION :
Option information : Display six numbers of 1 byte data. HDMI ID :
HDMI ID information : Display 4 byte data. CD number : Display 8 digit number Model name : Display 7 digit number LCD Panel Vender information display
The following Panel Vender and screen size are displayed. Panel Vender
Screen Size(Inch)
LPL
-23
SHP
-26
CMO
-32 -37 -47
Example : SHP-32 indicates that Vender is SHP and Screen Size is 32 inch.
- 9-4 -
9-10. STATUS CHECK MODE
1)
Press “9” button thrice on Remote Control during display of adjustment menu in the service mode. The status of this model will begin to check.
2)
During Status Check, the following displays are shown.
3
5
C
0
0
0
MAIN :
Main source information : Display RF position number (0 - 99) on the main screen, or Input Source (EXT1/2/3/HDMI etc.) MAIN FORMAT :
Display Video and PC format information MAIN PLL :
Main PLL information : Display 1 byte data at five. SCREEN SIZE :
Display the screen size as follows. Super live Cinema Subtitle 14:9 Wide 4:3 OTHER STATUS :
Other status information : Display three numbers of 2 byte data.
- 9-5 -
TOSHIBA
CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-01, JAPAN