Mikrotik SXT 5nD r2 Setup in Bridge Mode

Mikrotik SXT 5nD r2 setup in bridge mode

Mikrotik routerboard default IP is 192.168.88.1

You Yo u can connect with routerboard by W inBo throu!h IP and M"# address. You You need to download WinBo fro$ $ikrotik website.

By default routerboard have Admin as username and blank password.

If you want to connect with de%ice throu!h IP then don&t for!et to add sa$e network address into your 'c (I#) otherwise connection isn&t established. *lse you can connect throu!h M"# so choose M"# address fro$ *li'sis net to + connect + field.

When you lo!in) +,outer- /efault confi!uration+ screen is 'o 'u'. click okay.

/o sa$e for other de%ice to lo!in to router- If you followed the 'rocess then you already o'en both de%ice.

(ow you can set a 0ost(a$e for those de%ices. •

Click on the system button on the left then Identity

•

Change the name to something useful.

•

Make the change to both radios

Connecting ireless radio

te's to followed •

#lick the !ireless button on the top left

•

"lan#" interface is grayed or dimmed$ this means its currently disabled.

•

%ight click "!lan#" interface and click &nable from dorpdo!n menu or 'ust (lue Check button on top of menu b ar. )o! you can see the interface is enabled.

Its ti$e to chan!e radios de%ice to "ccess'oint and +#lient+

te' to followed to $ake "ccessPoint.  "ccess Point Configuration •

Double click on lan#

•

Click the !ireless tab at the top$ ne*t to +eneral tab

•

Click the Mode drop,do!n menu and choose "(ridge"

•

Click the (and drop,do!n menu and choose "5+h-,only,)"

•

n Channel idth drop,do!n choose "2/01/M- T 3bo4e

•

Choose "n42" on ireless ortocol

•

Click the T tab at the top$ ne*t to !ireless tab

•

6rom T +uard Inter4al drop,do!n menu choose "long"

•

Select all 1 T chain options and also select all T 3MD7 priorities

•

Click on DS tab$ on DS mode drop,do!n menu choose dynamic.

•

3nd DS Default (ridge "bridge#"

•

n )streme tab select "Disable CSM3" and 6ramer policy "dynamic si-e"

•

)o! select 3pply button on the top right.

Client Configuration te' to follow for client •

Double click on !lan#

•

Click on Scan button on the right

•

The 3 must sho! up$ if it isn8t$ follo! abo4e steps again$ if its does$ then click on the SSID sho!n in the list and click the "connect" button then 8close8

 "fter doin! so you ha%e connect client to "P. Wait we need chan!e so$ethin! $ore here .

o to back to the wireless tab. •

Click the Mode drop,do!n menu and choose "Station (ridge"

•

Click the (and drop,do!n menu and choose "5+h-,only,)"

•

n Channel idth drop,do!n choose "2/01/M- T 3bo4e

•

Click the !ireless protocol drop,do!n and choose "3ny"

•

) T tab ne*t to !ireless tab select 1 T chain options

•

6rom T +uard Inter4al drop,do!n menu choose "long"

•

Then select all T 3MD7 priorities

•

)o! click 3pply button on right side.

-n the wireless tables window you can see +,+ net to the Wlan Interface. his indicate the cleint is re!ister and connected to the "P.

Bandwidth test Between two 3 •

Click the Tools button on the left then choose (and!idth Test

•

Change the "Test To9" field to the address of the client , #:2.#;<.<<.#

•

6rom rotocol either choose "udp" or "tcp"

•

n Direction drop,do!n menu either choose of your choice

•

Click the "user" field and enter admin for the username.

•

)o! click Start button top right of the menu.

0ere is $y bidirectional #P test.