Maxsurf Training
12
Three ways to model a chine hull
There are three ways of producing surface discontinuities (or chines) in a hull: 1) Compacted control points Only a single surface, useful for blending a chine into a round bilge. More complicated fairing, more difficult to adjust spline stiffness. Non-optimum control point distribution for different areas of surface.
2) Using Bonded Edges Surfaces move together can be advantage or disadvantage
3) Trimmed surfaces Surfaces independent, each can be faired independently. Cannot blend to round bilge.
60
Maxsurf Training
For a complete list of steps to produce a chined hull using any of the above three methods, see Tutorial 5. 12.1. Step-by-step: Chine hull using linear surfaces Perhaps the simplest way to make a chine hull is to make the transverse flexibility of the surface linear (order 2). This will make the surface piecewise linear, with straight lines joining the control points. You can still maintain a smooth hull in the longitudinal direction by using a flexibility of 3 or more in the longitudinal direction. 12.1.1. Create a new design and add a default surface Select New from the File menu. If you have an existing design open, you will have to close it first. To add a surface select Surfaces | Add Surface | Default. This will add the default surface, which will be fine for this example. In the Perspective window, you should have something like this (turn on the Net to show all the control points, and turn on the Half display so that you see just one side – use the commands in the Display menu):
61
Maxsurf Training
12.1.2. Change the surface flexibility Note that the ends of the default surface you have just added are curved. We will now change the surface's transverse flexibility so that it is linear. Select Surfaces | Properties | Default:
you can then set the transverse flexibility to 2 (linear):
click OK and notice that the ends of the surface have now changed so that they are straight lines:
62
Maxsurf Training
12.1.3. Fairing the Profile The next stage is to fair the profile. To do this change to the Profile view:
We will add some shear to the hull by lifting the forward control point a little. Remember that there is only one control point here, so it can be selected just by clicking the mouse on it and dragging it to its final position:
Now move the forefoot up a bit. Remember, there are two points here so select them both by dragging a box over them:
Then click on the selected control points to move them:
12.1.4. Fairing the plan We will now fair the plan shape, so switch to the Plan window:
63
Maxsurf Training
First we will close the bow, by dragging all the forward control points onto the centreline: If you hold the shift key down whilst dragging them, they will only move in the vertical or horizontal direction. This helps to just move them into the centreline without moving them longitudinally:
Now close the transom a little. Remember that there are two points here so drag a box over the control points to select them both and move them into the centreline a little:
Review the design in the Perspective window, try turning on the rendering to get a better idea of the shape (Display | Render | Smooth Shading). Note, to get the best shading, ensure that the outside arrow is pointing outwards. Turn on the outside arrows in the Display menu, and click on the arrow's tip to flip its direction:
64
Maxsurf Training
12.1.5. Fairing the section In the Body Plan window you can fair the sections more accurately. Change to the Body plan view and don’t forget to turn off the Net so that you can only see the control points for the current column. Also turn off the rendering to speed up the program:
To better visualise the shape, we shall add some sections. This is done in the Data | Grid Spacing dialog:
Click the Add button and type 11 stations. Then click on the Space button and select "Evenly along the length of the model". When you click OK, the station positions will have been automatically calculated:
Click OK to close the window.
65
Maxsurf Training
In the Body Plan Window, when you click on one of the control point column indicators in the inset window, the current control point column will change and the closest section to this column will be displayed. Click on the indicator for the middle control point column
If you wish to have a single chine hull, simply move the chine control point to the desired location.
Then do the same thing for the aft control point row. First click on the left hand control point column indicator to get the aft control point column, then move the middle control point to get the desired deadrise:
You can then turn on all the sections (Display | Contours dialog, or ) It is also a good idea to turn on the use the Toolbar button "Feature Lines" in the Display | Contours dialog as this will highlight the chine:
66
Maxsurf Training
Also review the design in the Perspective window (you can turn off the Grid from the Display menu to see the shape more clearly):
12.1.6. Adding more chines You may want to add more chines to the design. To do this go back to the Body Plan view and select the middle control point column by using the control point indicator in the inset window:
To add a chine, we must add extra control point rows. To do this, select Controls | Add Row, or use the Toolbar button . Then click at the location where you want to insert the extra row. Add two rows as shown below:
67
Maxsurf Training
Then fair the control point positions for each of the columns to get the desired shape. You may also want to refine the design in the Profile view, especially to get the forefoot correct. Here is the final design in the Perspective view:
12.1.7. Controlling the longitudinal shape The longitudinal shape can be manipulated in the Plan and Profile views. You can also add more control point rows so that you have more control over the shape.
68
Maxsurf Training
69
