A nice training book on how RS232 communications function.
Descripción completa
protocolos de comunicacionDescripción completa
LCD RS232 Interface
TAFJ Set up on T24 banking system R14 and aboveDescripción completa
TAFJ Set up on T24 banking system R14 and above
how to installFull description
Full description
Full description
Cacti setup
kannaDescripción completa
hydroponicFull description
Descrição completa
Descripción completa
Descrição completa
Full description
Callsetup
MELDAS Series
M64 RS-232 Setup
USA-E US A-E99 9908 081 1 -150* -150*
MITSUBISHI MITSUBISHI EL ECTRIC ECTRIC A UTOMATION USA
List of Revisions R ev
Date of R evision
Detail
Author Author
*
08/03/04 08/03/04
F irst E dition dition Created
TSS TS S
Mitsubishi M64 control Using Using Procom P rocomm m P lus to upload and download download data data Hard key Soft key
Hard keys are located to the right of the display. Soft keys keys are located located under under the the display display..
Warning - The data data listed on these sheets sheets are set up to match our laptops. Use this data only as a guide.
Checking Checking the CNC CNC setup for Procomm Plus : 1 Pre Press the
TOOL PARAM
2 Pre Press the
MENU
3 P ress the
I/O P AR
key. key key unt until the
I/O P AR
key key appe appear ars. s.
key.
DEV. 1 is shown at the top of the display. 4 P ress the > (next page) key. Until This This shou should ld be page 3. ( the page age number is foun ound in the upper righ ight-ha -hand cor corner.) er.)
To move ove betw etween een pages us the
<
(pr (prev page) age) and and
>
5 Check the dat data a for each of the the following following param paramet eters: ers: P arameter
9201 9202 9203 9204 9205 9206 9207 9208 9209 9210
Data
P arameter
9211 9212 9213 9214 9215 9216 9217 9218 9219 9220
PRO 1 3 1 0 2 0 3 1
** Note ** To chan chang ge the data ata refer fer to the " M64 M64 I/O I/O set setup " proce ocedure.
Check Check the Procomm Plus set up. Term Terminal inal type Tran Transf sfer er Prot Protocol ocol Modem / Connection Baud rate Parity - Bits - Stop bits
ANSI B BS ASCl l Direct Connect Com 1 9600 E-7-2
The These shou should ld be foun ound at the bott ottom of the Proco Procom mm Plu Plus s scr scree een n.
Using P rocomm P lus
P age 1 of 7
Data
0 0 0 0 0 10 1 0
(nex (nextt page) age) keys. eys.
Transferrin Transferrin g data from the CNC CNC to th e Laptop 1 Connect Connect the P rocom rocomm m cable. cable. 2 Turn on the the Edit key key on your your contr control. ol. Check Check for for comput computer er and and CNC setup setup for Procomm Procomm Plus (See (S ee Page P age 1) NOTE :
To download or up load the ladder ladder you must f irst stop th e PLC. PLC. ( See See page 7 ) You must h ave the Edit Edit o n before you s top th e PLC. PLC.
For ALL1, ALL2, ALL3 compl ete backup downl oad, you must have EDIT EDIT ON, ON, and s top to p the t he PLC, then change ch ange BA SE PARAMETER PARAMETER 1060 1060 by *****PRESS *****PRESS IN E-STOP BEFORE B EFORE TURNING OFF PLC***** A Pre Press the
TOOL PARAM
B Pre Press the
MENU
C P ress the
Setup
D Pre Press the
Y
key and then the
INPUT
E P ress the
>
(next page) key. Until
1060
F Enter
key. key key unt until the
Setup Setup
key.
(1060) DATA(64) (S) and Press
3 Pre Press the
DIAG IN/OUT
4 Pre Press the
MENU
5 P ress the
OUTP UT
key key appe appear ars. s.
is shown on the display.
INPUT
Two Times.
key. key unt until the
OUTP OUT P UT
key appear appears. s.
key.
Along the bottom of the CNC display should be a line that looks like the following : #(
) DATA (
)(
)
6 Check the #12 DEVICE NO. It should be a 1 (PRO). You can can find ind this data ata in the upper righ ighthand and cor corner of the disp isplay lay. It is show shown n as : # 12 DEVICE NO. If it is not a 1 do the following : A) Type in the the following following : B) P ress the INP UT
Using P rocomm P lus
#( 12 ) DATA ( key.
P age 2 of 7
1)(
)
7 Set up P rocom rocomm P lus lus to to rece receiv ive e dat data a and and give give it a fil file e nam name. e. exam exampl ple e : test.p est.pro ro or test.pa est.parr or test.la est.lad d Note : After typing in a file name you must must hit save. Then Then Procomm P rocomm P lus is ready to receive. 8 According to what what Data Data you want want to to output type type in the following following : For NC programs For Parameters For ladder For ladder and messages For macros For a complete backup P arameters arameters w/ options options Offsets Ladder 9 P ress the
INP UT
#( 1 ) DATA ( AL L ) ( #( 3 ) DATA ( )( 250 ) ( #( 99 ) DATA ( #( 99 ) DATA ( AL L3 ) ( #( 30 ) DATA ( AL L ) (
) ) ) ) )
#( 99 ) DATA ( AL L1 ) ( #( 99 ) DATA ( AL L2 ) ( #( 99 ) DATA ( AL L3 ) (
) ) )
key.
10 Y ou should see the the CNC display showing the data being output outputted. ted. COMPLETE " When it is done the CNC display will show " DATA OUT COMPLETE
11 On the the P rocomm rocomm P lus screen click the the save.
Using P rocomm P lus
The file is now saved
P age 3 of 7
Transferrin Transferrin g data from the Laptop t o th e CNC CNC for CNC's CNC's already already s etup 1 Connect Connect the P rocom rocomm m cable. cable. 2 Turn on the the Edit key key on your your contr control. ol. Check Check for for comput computer er and and CNC setup setup for Procomm Procomm Plus (See (S ee Page P age 1) NOTE :
To download or up load the ladder ladder you must f irst stop th e PLC. PLC. ( See See page 7 ) You must h ave the Edit Edit o n before you s top th e PLC. PLC.
3 Pre Press the
DIAG IN/OUT
4 Pre Press the
MENU
5 P ress the
INP UT
key. key key unt until the
INPUT
key key app appear ears.
key.
Along the bottom of the CNC display should be a line that looks like the following : #(
) DATA (
)(
)
6 Check the #12 DEVICE NO. It should be a 1 (PRO). You can can find ind this data ata in the upper righ ighthand and cor corner of the disp isplay lay. It is show shown n as : # 12 DEVICE NO. If it is not a 1 do the following : A) Type in the the following following : B) P ress the INP UT
#( 12 ) DATA ( key.
1)(
)
7 According to what what Data Data you want want to receive receive type type in the the following : #( 1 ) DATA DATA ( 9999 9999 ) ( For NC programs #( 3 ) DATA ( )( For Parameters #( 99 ) DATA ( )( For ladder and messages For a com plete restore, Use Complete Restore Restore up load Pocedure #( 99 ) DATA ( )( P arameters arameters w/ options options #( 99 ) DATA ( )( Offsets Ladder #( 99 ) DATA ( )( Do not press the
INPUT
) ) ) ) ) )
ALL1 ALL2 ALL3
key yet.
Note : If you try to receive an NC program that already exist you will get an alarm 8 Set up up the the Laptop to to send the the data. data. You Y ou must must choose the the file you you want want to send. You sen send by doub ouble clic click king ing the file ile you want.
Do not send the fi le yet. 9 P ress the
INP UT
key.
10 Send the the data data from the the Laptop. You only only have ave 10 seco secon nds to star startt sen sending ing the data ata aft after you hit the INPUT key. 11 When it is done the CNC will show " DATA IN COMPLETE " 12 P ower ower off off or resta restart rt the PLC. PL C.
Transferrin Tra nsferrin g Pdata CN Restore U sing P rocomm lus from the Laptop to theP aCNC ge C 4 ofor f 7 Complete Restore
1 Connect Connect the P rocom rocomm m cable. cable. 2 Turn on the the Edit key key on your your contr control. ol. Check Check for for comput computer er and and CNC setup setup for Procomm Procomm Plus (See (S ee Page P age 1) NOTE :
To download or up load the ladder ladder you must f irst stop th e PLC. PLC. ( See See page 7 ) You must h ave the Edit Edit o n before you s top th e PLC. PLC.
For Complete Compl ete Restor Restore e you mu st c hange BASE PARAME PARAMETE TER R 106 1060 0 by Turn EDIT ON, and stop the PLC A Pre Press the
TOOL PARAM
B Pre Press the
MENU
C P ress the
Setup
D Pre Press the
Y
key and then the
INPUT
E P ress the
>
(next page) key. Until
1060
F Enter
key. key key unt until the
Setup Setup
key.
(1060) DATA(64) (S) and Press
3 Pre Press the
DIAG IN/OUT
4 Pre Press the
MENU
5 P ress the
INP UT
key key appe appear ars. s.
is shown on the display.
INPUT
Two Times.
key. key key unt until the
INPUT
key key app appear ears.
key.
Along the bottom of the CNC display should be a line that looks like the following : # ( ) DATA ( )( ) procedure 6 Check the #12 DEVICE NO. It should be a 1 (PRO). If not see Above procedure
AL L1 command From the Computer 7 Must Upload ALL1 8 Set up up the the Laptop to to send the the data. data. You Y ou must must choose the the file you you want want to send. You sen send by doub ouble clic click king ing the file ile you want.
Do not send the fi le yet. 9 Type in the following : 10 P ress the
INP UT
#( 99 ) DATA (
)(
)
key.
10 Send the AL L1 data from the Laptop. You only only have ave 10 seco secon nds to star startt sen sending ing the data ata aft after you hit the INPUT key. 11 When it is done the CNC will show " DATA IN COMPLETE " 12 P ower ower off off the the CNC off and and back back on on
1060 see above on how to get there 13 Reset up the Base Parameter 1060 Using P rocomm P lus P age 5 of 7
A Ent Enter
(1060) DATA( 1) ( ) and Press
INPUT
B The following following message message will be displayed displayed "S "Standa tandard rd param paramet eter er setting? setting? (Y /N)"
and press Typ Type in N #(1060) DATA(1 ) (N) You Will Will see see the follo ollow wing ing #(1060)
INPUT
C The following following message will will be be displaye displayed d "F "Format ormat? ? (Y /N)"
Y and press Typ Type in #(1060) DATA(1 ) (Y) You Will Will see see the follo ollow wing ing #(1060)
INPUT
After the Y is Inputted , "Format Is Complete" appears on the screen PAR setup from page one 14 Check the Procomm p lus I/O PAR
15 Press Press tth he
DIAG IN/OUT
16 Press Press tth he
MENU
17 P ress the
INP UT
key. key key unt until the
INPUT
key key app appear ears.
key.
Along the bottom of the CNC display should be a line that looks like the following : #(
) DATA (
)(
)
procedure 18 Check the #12 DEVICE NO. It should be a 1 (PRO). If not see Above procedure 19 According to what Data you want want to to receive type type in the following : Upload ALL1,ALL2, ALL3, Programs, and Parameters #( 99 ) DATA ( #( 99 ) DATA ( #( 99 ) DATA ( #( 1 ) DATA DATA ( #( 3 ) DATA (
P arameters arameters w/ options options Offsets Ladder For NC programs For Parameters Do not press the
INPUT
)( )( )( 9999 9999 ) ( )(
) ) ) ) )
Upload Upload Upload Upload Upload
key yet.
Note : If you try to receive an NC program that already exist you will get an alarm 20 Set up the the Laptop to send the the data. data. You Y ou must must choose the file you want want to to send. You sen send by doub ouble clic click king ing the file ile you want.
Do not send the fi le yet. 21 P ress the
INP UT
key.
22 Send the the data data from the the Laptop. You only only have ave 10 seco secon nds to star startt sen sending ing the data ata aft after you hit the INPUT key. 23 When it is done the CNC will show " DATA IN COMPLETE " 24 P ower ower off off or resta restart rt the PLC. PL C.
Using P rocomm P lus
P age 6 of 7
ALL1 ALL2 ALL3 PRO PAR
Stopping Stoppi ng The PLC PLC To STOP the PLC do one of the following : *****PRESS IN E-STOP BEFORE TURNING OFF PLC***** Turn the Rotary Switch to 1 from 0. (See picture below) 1 Tur
Rotary Switch
OR 2
A) P ress the B) Press Press the the
FO FILE
key. key.
Then pr press the Then press the
1
key.
key. key.
The The disp isplay lay will ill show show PLC RUN or PLC STOP
You can can tell ell what stat state e the PLC is in at this poin oint. C) Press Press th the
MENU RUN/SP
Then pr press the
The The disp isplay lay will ill show show PLC STOP.
INP UT
key.
Note if the READY light was on it will go out.
To put the PLC back back in the RUN mode do the following : A) Press Press the the B) Press Press the the
FO FILE
key. key.
You can can tell ell what stat state e the PLC is in at this poin oint. C) Press Press th the
0
key.
Then pr press the Then press the
key. key.
The The disp isplay lay will ill show show PLC RUN or PLC STOP Then pr press the
The The disp isplay lay will ill show show PLC RUN.
