Lots of Bcm3382 Console Commands

bcm3382 console commands from my Huawei Mt130u Enjoy -thalungz ~SBH~

CM DOCSIS Commands Available Commands: con_high mutex_debug run_app taskInfo taskTrace ----

cpuLoad ping shell taskPrioritySet usfsShow

exit read_memory socket_debug taskResume version

mbufShow reset stackShow taskShow write_memory

memShow routeShow taskDelete taskSuspend zone

Available sub-command tables: [Console] [HeapManager] [HostDqm] [cm_hal] [docsis_ctl] [dtp] [embedded_target] [enet_hal] [event_log] [fam] [flash] [forwarder] [ftpLite] [ip_hal] [msgLog] [non-vol] [pingHelper] [snmp] [snoop] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Telnet/SSH Interactive Session Commands (Console)

Description: Telnet/SSH Interactive Session Commands Available Commands: exit ----

reset

set

show

Available sub-command tables: [cm] [ethernet] [ftpLite] [pingHelper] [system] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM Command Table (cm)

Description: CM commands Available Commands: diag ----

log

ping

set

show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Ethernet Command Table (ethernet)

Description: Ethernet Commands

Available Commands: diag ----

show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

FTP Lite Client Commands (ftpLite)

Description: FTP Lite Client settings and commands. These commands allows you to configure th e FTP Lite Client. Available Commands: ftp ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Ping Commands (pingHelper)

Description: Ping Helper Thread settings settings and commands. commands. These commands allow you to set the ping utility up with precise control over packet sizes, timeout values, etc. Available Commands: all_sizes end_size ip_stack ip_sweep restore_defaults step_amount stop verify_enable wait_enable ----

hs_nowait hs_wait number_of_pings ping show_settings start_size time_between_pings wait_time

ip_address stats verbosity

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

System Command Table (system)

Description: System commands Available Commands: diag ----

pktlog

set

show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

HeapManager Commands (HeapManager)

Description: Broadcom Heap Manager (malloc/free) settings and commands. Available Commands:

bcheck memShow trace ----

bcheck_crash options walk

bcheck_enable stats walk_alloc

last_error maxAlloc threadUsage time walk_alloc_time

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

HostDqm Interface Commands (HostDqm)

Description: Commands to show/change the HostDqm IF state. Available Commands: show ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM DOCSIS HAL Commands (cm_hal)

Description: Commands to show/change the CM DOCSIS HAL state. Available Commands: ackcel_show add_mcast_dsid center_tuner change cpe_add cpe_del delete_mcast_dsid dsb_reset dsid_helper fpga_amp hal_show locate_maps lock_ds map_lead_time_show qosParms read_mbr set_mode show tune_band tuner_module us30_clear_debug_counters us30_clear_debug_count ers us30_set_debug_flow us_multi_cw_transmit us_sweep us_transmit ----

add_reseq_dsid bist_test channelizer_state cpe_max cpe_print dpm drw_show errors fft_dump ldaix_read lna_read log mac_diag multicast_table packets_queued scan_ds scan_stop show_halif transmit tuner_read tuner_wideband us30_debug_counters us_burst us_cw_transmit us_multi_transmit utp_status write_mbr

cam_dump counters ds_state fft_store lna_write mac_reset qam_lock set_drw tune tuner_write us30_flowsize us_debug us_reset

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM DOCSIS DOCSIS Control Control Thread Thread Commands Commands (docsis_ctl) (docsis_ctl)

Description: Commands to change the state of the DOCSIS Control thread. Available Commands: ClearCmCert clear_image dbc_msg_inject goto_ds log_messages

binarySfid cm_ctrl dload goto_us map_debug

bpiShow comp_mac_to_phy dsdiag igmpShow mdd_modify

cfg_hex_show comp_phy_to_mac dsx_show ip_initialize mdd_sets_show

cfg_tlv_show copy_image event_censor ip_show modem_caps

override_ucd_max_burst reseq_dsid_regress_test reseq_dsid_regress_tes t state stop_download us_phy_oh_show usdiag ----

publish_event rng_rsp ucdShow

rate_shaping_enable scan_stop showFlows ucddiag up_dis

Available sub-command tables: [dsxTest] [propane_ctl] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Dynamic Service Test Command Command Table Table (dsxTest) (dsxTest)

Description: Commands to test dynamic service. Available Commands: addConfigFile delSfids ----

autoDsxTest dropDsxMsg

changeConfigFile dscLocal dsdLocal

delRef show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM Propane Propane Control Control Thread Thread Commands Commands (propane_ctl) (propane_ctl)

Description: Commands to change the state of the Propane Control thread. Available Commands: debug psi_grant ----

discovery release_psis

dsx_complete request_psis

oper_caps show

port_number simulate

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

DTP Commands (dtp)

Description: Commands to control DTP state. Available Commands: change_dsid read_counter ----

create_dsid show

delete_dsid stack_check

max_tokens

ping_dtp

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Embedded Target Commands (embedded_target)

Description: Commands to control the embedded target platform.

Available Commands: cache_test cp0_read fpm_show icache stop_perf_counters ----

cp0_write sdram_test test_fpm

dcache deplete_fpm start_perf_counters

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Ethernet HAL Commands (enet_hal)

Description: Commands to show/change the Ethernet HAL state. Available Commands: autoneg read_mii write_mii ----

down show

force_link speed

full_duplex transmit

hal_show up

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Event Log commands (event_log)

Description: Commands to manipulate the Event Log Available Commands: control silent ----

flush stop_stress

log_event stress

read syslog

show verbose_show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Forward Assist Manager Commands (fam)

Description: Commands to show the ForwardAssistManager object. Available Commands: set ----

show

Available sub-command tables: [compilers] [filters] [trees] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

FlexibleFilterCompiler Commands (compilers)

Description: Commands to show FlexibleFilterTree objects.

Available Commands: show ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

FlexibleFilter Commands (filters)

Description: Commands to show FlexibleFilterTree objects. Available Commands: show ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

FlexibleFilterTree Commands (trees)

Description: Commands to show FlexibleFilterTree objects. Available Commands: show ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Flash Driver Commands (flash)

Description: Commands to control the flash device driver. Available Commands: autoTest erase show ----

cfi_show init write

close open writeArray

configRegion read

deinit readDirect

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Forwarder Commands (forwarder)

Description: Commands to show/change the Forwarder state. Available Commands: allow_loopback halif_show lt_clear

filter_logging_enable ip_filter_logging lt_delete lt_max_entries

filter_logging_show log_packets lt_add lt_show

mac_filter_logging proto_filter_logging ----

port_filter_logging show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

FTP Lite Client Commands (ftpLite)

Description: FTP Lite Client settings and commands. These commands allows you to configure th e FTP Lite Client. Available Commands: clear_counters show_settings ----

counters

debug

ftp

ip_stack

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

IP Stack HAL Commands (ip_hal)

Description: Commands to manage IP stacks and related tasks. Available Commands: advertise dhcpv6_debug ipconfig print_nd ----

bootloader discover ipv6config show

clientif_debug dhcpc_debug dload hal_show kill_remote_dhcp_server kill_remote_dhcp_serve r test

dhcpc_show ip_addr_show lease_show

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Message Log Settings Commands (msgLog)

Description: Commands for changing Message Log Settings. These commands commands allow you enable and disable display fields and severity levels for individual objects or for groups of objects. Available Commands: fields ----

severities

show_settings

Available sub-command tables: [remoteAccess] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table: Description:

Remote Access Server Commands Commands (remoteAccess)

Remote Access Access (Telnet/HTTP/SSH/etc) (Telnet/HTTP/SSH/etc) settings and and commands. These commands commands allow you to configure the Telnet, SSH or other supported servers. Available Commands: read_default_settings ----

restart_server

start_server

stop_server

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Non-Volatile Settings Commands (non-vol)

Description: Commands to change the non-volatile settings for the application. Available Commands: clear_device read write ----

defaults show

del_extra_data stats

flush tftp_read

manufactured tftp_write

Available sub-command tables: [HuaWei_Non] [bfcApp] [bpi] [docsis] [docsis30] [ds-cal] [event_log] [factory] [halif] [mfirew] [propane] [snmp_cm] [us-cal] [userif] [vendor] -------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

HuaWei NonVol Commands (HuaWei_Non)

Description: Commands to show/change the HuaWei Factory NonVol settings. Available Commands: BackupValuesShow {flush} manufactured tftp_read tftp_write ----

clear_device read write

defaults show

del_extra_data stats

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

BFC Application Settings Commands (bfcApp)

Description: Commands to change the non-volatile settings for the BFC Application. Available Commands: auto_console del_extra_data read tftp_write ----

clear_device console_stop_prompt driver_init_prompt {flush} serial_console show stats write

defaults manufactured tftp_read

--------------------------------------------------------------------------------------------------------------------------------------------------------

Command Table:

CM BPI NonVol Commands (bpi)

Description: Commands to show/change the CM BPI NonVol settings. Available Commands: change_key del_extra_data read write ----

clear_device {flush} show

code_access key_location stats

cvc_access manufactured tftp_read

defaults print tftp_write

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM DOCSIS NonVol Commands (docsis)

Description: Commands to show/change the CM DOCSIS NonVol settings. Available Commands: bpi_version del_extra_data enable manufactured read startup_dsfreq timer_disable us_power ----

clear_device concat_thresh cpe_interface defaults dhcp_settings doc10_mcastpromisc ds_frequency fake_reg {flush} ip_stack_number last_annex max_concat queues rate_shaping_time rng_class_extension show startup_context startup_uschan stats tftp_read tftp_write ugs_depth ugs_table_entries us_channel write

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM DOCSIS DOCSIS 3.0 NonVol Commands Commands (docsis30)

Description: Commands to show/change the CM DOCSIS NonVol settings. Available Commands: clear_device {flush} stats tod_ip ----

defaults ip_prov_mode tcs_params write

del_extra_data manufactured tftp_ip

enable read tftp_read

ext_us_tx_power show tftp_write

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table: Table:

DOCSIS CM Downstream Calibration Calibration NonVol NonVol Commands Commands (ds-cal)

Description: Commands to show/change the DOCSIS CM Downstream Calibration NonVol settings. Available Commands:

clear_device {flush} num_coef show write ----

clear_tables frequency num_freq stats

coef ldaix_time num_ldaix tftp_read

defaults manufactured offset tftp_write

del_extra_data master read tuner_step

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

DOCSIS EventLog NonVol Commands (event_log)

Description: Commands to show/change the DOCSIS EventLog NonVol settings. Available Commands: clear_device {flush} tftp_read ----

clear_event manufactured tftp_write

defaults read write

del_extra_data show

event stats

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Factory NonVol Commands (factory)

Description: Commands to show/change the Factory NonVol settings. Available Commands: clear_device manufactured stats ----

defaults read tftp_read

del_extra_data scratch_pad tftp_write

{flush} show write

key sn

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

HalIf NonVol Commands (halif)

Description: Commands to show/change the HalIf NonVol settings. Available Commands: 3420_optimized_map DS_AGI DS_AGT STABW2 STAGI STAGT STATHR bcmalloc bcmalloc_numSizes board_rev bt_master_enable chan_plan_annex_b cm_1024qam cm_20_clipping cm_45 cm_45i cm_aboard_v3 cm_adv_map_runahead cm_amp cm_cboard cm_clc cm_diplexer cm_ds_ref_freq cm_iboard_v1b cm_phy_ref_freq cm_sboard cm_tuner cm_upstream_priority_queue_support cm_us_ref_freq cm_us_sample_freq cm_wideband_tuner del_extra_data eth_autoneg eth_duplex_full eth_reject_cam fap_bypass {flush} fpm_token_depletion_wdog_enable fpm_token_depletion_wd og_enable

STABW1 STPGA1 clear_device cm_aboard_v2 cm_annex cm_iboard_v1a defaults eth_speed high_output_pa

hpna_message_level mac_address manufactured power_save_enable scdma_code_matrix stats tftp_read usb_rndis usb_vendor_id zone ----

interfaces local_bt_mac_address num_enabled_tuners read remote_bt_mac_address shack_tries show spreader_scale tftp_write usb_device_id usb_mac_address wdog_enable wdog_timeout write

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Mini Firewall NonVol Commands (mfirew)

Description: Commands to show/change the Mini Firewall NonVol settings. Available Commands: clear_device manufactured tftp_write ----

defaults read write

del_extra_data show

enable stats

{flush} tftp_read

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM Propane NonVol Commands (propane)

Description: Commands to show/change the CM Propane NonVol settings. Available Commands: clear_device manufactured tftp_write ----

defaults read timer

del_extra_data show write

enable_propane stats

{flush} tftp_read

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM SNMP NonVol Commands (snmp_cm)

Description: Commands to show/change the SNMP NonVol settings. Available Commands: allow_config clear_device docsDevSerialNumber docsDevSwFilename {flush} manufactured stats sysContact tftp_write write ----

defaults del_extra_data docsDevSwAdminStatus docsDevSwOperStatus max_dload_tries read sysLocation sysName

dload_tries docsDevSwServer show tftp_read

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table: Table:

DOCSIS CM Upstream Calibration Calibration NonVol NonVol Commands (us-cal)

Description: Commands to show/change the DOCSIS CM Upstream Calibration NonVol settings. Available Commands: board_rev control {flush} show ----

clear_device copy manufactured stats

clear_table def_table offset tftp_read

cm_amp defaults print tftp_write

config del_extra_data read write

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

User Interface NonVol Commands (userif)

Description: Commands to show/change the Message Log NonVol settings. Available Commands: clear_device defaults del_extra_data dhcp_settings fields {flush} http_acl_host_add http_acl_host_remove http_acl_hosts_clear http_admin http_adv_ipstacks http_enable http_ipstacks http_password_idle_timeout http_password_idle_tim eout http_password_seed http_socket_show http_user inactivity_timeout ip_stack_number manufactured password read severities show ssh_enable ssh_ipstacks stats telnet_enable telnet_ipstacks tftp_read tftp_write user_name ve_ip_stack_number write ----------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

CM Vendor NonVol Commands (vendor)

Description: Commands to show/change the CM Vendor NonVol settings. Available Commands: clear_device manufactured tftp_read ----

defaults read tftp_write

del_extra_data show write

ds_freq standby

{flush} stats

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Ping Commands (pingHelper)

Description: Ping Helper Thread settings settings and commands. commands. These commands allow you to set the ping utility up with precise control over packet sizes, timeout values, etc. Available Commands:

all_sizes end_size ip_stack ip_sweep restore_defaults step_amount stop verify_enable wait_enable ----

hs_nowait hs_wait number_of_pings ping show_settings start_size time_between_pings wait_time

ip_address stats verbosity

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

SNMP Commands (snmp)

Description: SNMP commands. Available Commands: agent_core_show get n2m severities tlv_55 ----

cm_cfgfile group_members notify_setup show trap

cm_filter_test install_group parent_chain test view_v1v2

debug key_v3 reset thread_info

flush log set throttle

-------------------------------------------------------------------------------------------------------------------------------------------------------Command Table:

Snoop Commands (snoop)

Description: Commands to show/change the state of Snoop objects. Available Commands: debug ----

enable

priority

show

--------------------------------------------------------------------------------------------------------------------------------------------------------