Work Planner
Quick Start Guide for the Program Control
!
This quick start guide provides a quick overview of the selected operation procedures and functions of the LICCON Work Planner. However, it does not replace the detailed user and reference manual with the important explanations and warning notes.
i Symbols in this quick start guide:
Press the left mouse button
Double click the left mouse button.
Press the right mouse button
Press the right or left mouse button
The description applies only for cranes with "Setup1" set up procedure
i The LICCON Work Planner differentiates 3 crane generations and, accordingly, has differences in the display and behaviour. The 3 crane generations are:
1crane with
LICCON
2crane with
LICCON
2crane with
LICCON
Overview of menu program
1
2
3
4
1 Display of program version 2 Load chart program 3 Work Planner program 4 Crane search program
Access to the Work Planner program
3
2
1
1 Select Manual crane selection in the planner column 2 Select your crane 3 Work Planner program starts with the selected crane
Overview of Work Planner program Setting bar
Side view, overhead view, support forces / surface pressures
Crane configuration This bar is missing for Setup2 cranes.
Graphic display of load The extent of the graphics can vary by crane.
Wind speed calculator
Wind surface calculator
Overview of Work Planner program Status and icon bar
4 1
2
5 6
3
7
9 Icon bar 1 End the program 2 List of all crane configurations 3 Draw interfering edge for the load case search 4 Measure / zoom / move in the view 5 Draw and delete lines, circular arcs and texts 6 Turn the entire crane
Status bar Display of crane type, crane number, set set up
7 List of all solutions from the load case search
8
Overview of Work Planner program Operating data fields & crane movements
2
1
1 Operating data fields (BDF) for the crane operation 2 Relative crane movements 3 Absolute crane movements
3
Work Planner program Configuring the crane
1
2
3
4
5 1 Main boom 2 Accessories 3 Ballast 4 Support for LTM crane Central ballast for LR crane
5 Slewing range
Work Planner program Configuring the crane
1
3
2
1 Work Planner window 2 Setup2 window 3 Overview of the categories in the Setup2 window
Work Planner program Configuring the crane
1 2
1
2
1 Select element to be set. The category is marked in pink in the process.
3
2 Assign an available value for the selected element. The chart code changes.
3 Alternative: Direct entry of the chart code
Work Planner program Adding to the crane configuration
3 1 2
4 1
1 Select element to be set. The category is marked in pink in the process.
2 Assign an available value for the selected element 3 Selected element contains several properties. First, select the property to be set.
4 Assign an available value for the selected property.
Work Planner program Completing the crane configuration
2
1
1 The crane configuration can be completed. 2 Invalid crane configuration. The configuration must be changed.
i
Appendix Touch control
Conversion of mouse - touch
Press the left mouse button
Briefly tap on an element
Press and hold the left mouse button
Briefly tap on an element and drag your finger to the side
Press the right mouse button
Press on an element approx. 1 second and wait until a rectangle indicates the c hangeover
Press and hold the right mouse button
Press on an element approx. 1 second and wait until a rectangle indicates the changeover and then drag your finger to the side
i
Appendix Contact address
If you have any questions or problems with the LICCON W ork Planner, or if you would like to forward any suggestions, please contact your sales representative or contact
P.O. Box 1361 89582 Ehingen/Donau Germany Telephone: E-Mail: World Wide Web:
+49 (0) 73 91 / 502 - 0
[email protected] http://www.liebherr.com