TECHNICAL SERVICE MANUAL FOR KEMPOWELD MACHINES
TECHNICAL SERVICE MANUAL FOR KEMPOWELD GENERAL MAINTENANCE OF KEMPOWELD
Maintenance of Kempoweld power source will normally consist of general cleaning of unit with soft brush and vacuum cleaner, and checking of wearing for parts like: switches,connectors, potentiometers and fuses. NOTE! If you use compressed air for cleaning, there is a risk that dirt is packed even more tightly into gaps of connectors or components, so be carefull with those parts! Maintenance of the wire feeder and mig gun will normally consist of general cleaning and change of consumable parts like: contact tube, contact tip, contact tip adapter, gas nozzle, wire conduit, feeding rolls, guide tubes, and gear wheel. The number of machines in will determine to what extend consumable- and spare parts will be stocked. WARNING
Watch out for the mains voltage! Disconnect the power source from mains voltage before removing cover plates or any testing or measurement and before troubleshooting look for signs of over heating, fractures and damages from internal components and power semiconductors. TROUBLESHOOTING CHART TROUBLE
CAUSE
REMEDY
The KEMPOWELD won´t start at all, any of the auxiliary devices won´t start.The signal lamps of machine are not switched on.
Blown fuse in mains supply voltage.
Check all three supply voltage phases; check fuses.
Faulty mains cable.
Check mains voltage from terminal block X001, repair cable if needed.
Broken main switch.
Check the main supply voltage before and after main switch, c hange switch if needed.
Faulty auxiliary transformer T002 or bad connection in connector X9, 400V or 0V.
Check transformer, repair transformer connection or change if needed.
Blown fuse F001 8A.
Check fuse and change if needed.
Faulty connection in control lines.
See, TABLE FOR CONTROL LINES, table 1.
Blown fuse F001 8A.
Check/change fuse F001.
Broken PCB.
See, TROUBLE SHOOTING FOR PCBs appendix 1.
The wire feeding unit K200/400 won´t work.
TECHNICAL SERVICE MANUAL FOR KEMPOWELD TROUBLESHOOTING CHART TROUBLE
CAUSE
REMEDY
The cooling unit don´t start or pilot lamp Hw3 lacking water pressure is iluminated.
Blown fuse F002 2A.
Check and change the fuse if needed.
Auxiliary transformer T002.
Check the voltage from transformer in the terminal block between 2.1 and 2.2, it should be 230v.
Pressure switch S005
Check the voltage over the pressure guard or from PCB A002 X2/1 and X2/8; enough pressure 0V and lack of pressure c. 5V.
5µF capacitor C001.
Check and change the capacitor if needed.
Broken PCB.
See, TROUBLE SHOOTING FOR PCBs appendix 1.
The The sole soleno noid id valve valve Y00 Y001 1 don´ don´tt work. work.
Faul Faulty ty sol solen enoi oid d valve valve or PCB PCB A001. A001.
Chec Check k the the 24 VDC VDC fro from m conn connec ecto tor r X3/5 and X3/6, change valve or PCB.
Wire feeding motor don´t work.
B lo lown fuse F001 8A
Check/change the fuse if needed.
The control cable between feeder and power souce is broken or it is not properly tightened.
Check and repair the control cable if needed. See table 1.
Faulty motor or PCB A001in K200/400.
Check the motor voltage from A001 X4/12 and X4/13 max. is c. 24 VDC, if it´s all right motor is faulty.
Broken PCB. Welding quality is bad: - arc is not stable - there are lot of spatters - bad arc start - not enough arc voltage
See, TROUBLE SHOOTING FOR PCBs appendix 1.
One phase is missing.
Check all phases from the therminal block X001. Change mains fuse if needed or tighten mains cables.
Faulty main transformer T001.
Check that voltages are symmetric over the three spools of T001. Variation of voltage is depending on voltage selection and load; normally it is between 10 VAC and 32 VAC. OCV variation range is 11 VAC to 35 VAC
Faulty main switch S001 or contactor K001.
Measure first main switch if it is all right check the contactor.
Shielding gas is missing.
Check the valve according the instructions mentioned above.
Gas hose of the gun is leaking or connection is loose.
Check/repair the mig gun.
Broken diode in the secondary. rectifier G001.
Check and change diode(bridge) if needed.
TECHNICAL SERVICE MANUAL FOR KEMPOWELD TROUBLESHOOTING CHART TROUBLE
CAUSE
REMEDY
Welding stops occasionally or some other occasional disturbances.
Faulty intermediate cable or connector.
Check/repair the cable. See TABLE FOR CONTROL LINES, table 1.
Faulty switch in mig gun.
Check and change the switch if needed.
Loose start wire(s) in mig gun.
Check and tighten the start wire(s) inside the gun.
Faulty fan or PCB A001 .
Check the 24 VDC voltage from fan connector X2/12 and X2/13, if it is all right change the fan, if it is not change the PCB.
Machine is overheating because the fan don´t start.
See, TROOUBLE SHOOTING FOR PCBs appendix 1. Wire feeding speed set value can´t adjusted.
The set value potentiometer RW102 is faulty.
Check and change the 10K Ω set value potentiometer RW102 if needed.
KMW-sync is not working.
Faulty connection in connector X1.
Check and repair connection according to PICTURE 1.
If some other push-pull gun than Binzel or Hulftegger is in use the gun is pulling to fast.
Wrong motor voltage.
Select correct jumper combination (there are two jumpers X1 and X2 and the fine adjustment for voltage can made from MP-SYNC PCB) from MP-SYNC control card. See also PICTURE 2.
MSD-1 me meter un unit do don´t wo work .
Ribbon ca cabl e between MS MSD-1 an and control card A001 is loose or cut.
Check and tighten the cable, check also the control voltage for MSD-1 from A001 X3/16 and X3/1 the value should be 12 V.
Faulty MSD-1 unit.
Check as mentioned above if it´s all right, chage the MSD-1.
Ribbon cable between KMW-timer and control card A001 is loose or cut.
Check and tighten the ribbon cable.
Faulty KMW-timer unit.
Check and change the KMW-timer unit. See also potentiometers from
Occasional disturbances with KMWtimer unit.
PICTURE 3.
The water circulation stops after 5 s of welding.
Low cooling water volume.
Check the water and fill it if needed.
Air bubbles or leakages in cooling system.
Follow the instructions of Kempoweld Operation Instructions/ Operation Disturbances.
Faulty pressure switch
Check/change the pressure switch.
TECHNICAL SERVICE MANUAL FOR KEMPOWELD TABLE 1. CONNECTORS AND CONTROL LINES KEMPOWELD CONNECTORS X006 AND K200/400 XW101 XW101 / X006
K200/400 A001
KEPOWELD A001
VALUE
B C D
X3/1 X3/8 X3/7
X8/3 X2/1 X2/11
30 VAC 30 VAC START
PICTURE 1. KMW-SYNC CONNECTION
A B C D E F HC-start
G H
M
TECHNICAL SERVICE MANUAL FOR KEMPOWELD PICTURE 2. A004 MP-SYNC CONTROL CARD
X1 X2
X3 A004
PICTURE 3. PCB OF K400 TIMER UNIT R 15 R 19
R 11
X1
Potentiometers:
R11 = Gas post flow R15 = Cycle time R 19 = Pause time
TECHNICAL SERVICE MANUAL FOR KEMPOWELD PICTURE 4. A001 PCB OF K400
V2
V3 X6
X3 C3 C4
C5
C6
X7
R24
X4
Potentiometer:
R24 = Adjustment of wire feed speed
TECHNICAL SERVICE MANUAL FOR KEMPOWELD APPENDIX 1. TROUBLESHOOTING FOR PCBs A001 POWER SOURCE
1. 2. 3. 4. 5. 6. 7. 8.
+ 24 V over the capacitor C9 + 24 V over the capacitor C7 (FAN POWER SUPPLY) + 15 V over the over the diode V2 + 12 V over the capacitor C10 (MSD POWER SUPPLY) START => pin X2/11 to GND, 0V = start active START => V4 to GND, 0V = start active TP 4 = 15 V, FAN ON CONTROL FAN TIMER voltage over C3 under 5 V = stop, over 10 V = on
A001 WIRE FEEDER
1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
11.
30 VAC VAC betwe etween en the the thyr thyris istr tros os anod anode es + 40 V over the capacitor C3 + 15 V over the diode V17 S YNCRONIZATION TP 19 (rectified sine wave) RAMP WAVE over the capacitor C11 (the wave is only active when start or wire feeding is on) START TP13; 0V ON, 15 V STOP BREAK CONTROL TP24 ; OV active 15 V stop BURN BACK /POST GAS TIMER TP33; 15 V stop, under 2V on CONTACTOR CONTROL TP 32; under 1 V off, over 5 V on I FAN CONTROL TP 34; under under 1 V off, off, over 10 V on II FAN CONTROL, voltage over the capacitor C17 < 2 V fan f an off < 6V fan on SET VALUE FOR WIRE FEEDING SPEED pin X2/1 and GND; voltage between 0 V - 15 V depending on potentiometer setting
TECHNICAL SERVICE MANUAL FOR KEMPOWELD A002 WATER COOLING UNIT
1. 2. 3. 4. 5. 6.
+ 24 V over the capacitor C5 + 15 V over the capacitor C6 START TP 1 => 15 V PRESSURE SWITCH pin X2/1 to GND; 0V pressure OK, 24 V no pressure THERMAL PROTECTION between pins X2/3 and X2/6; 0.1 V - 0.3 V normal temperature, over temperature over 3V PUMP TIMER; TP 3 on > 5 V off < 1 V TP 18 on ≈ 0.6 V off < 0.2 V
7.2.2000/V211203
KEMPOWELD 2501 Order no.
Part
Description
4279480 3143990 9772551 9750159 9775729 9764112 3143880 9544213 9761225 9760603 3143810 3141290 9771530 4191441 2070060 2070330 2070080 2070340 2070350 3001873 3001875 1028120 2061410 9547105 9547770 2062900 3138950 3144210
A001 C001 F001 G001 H001 K001 L001 M001 S001 S002 T001 T002 X003 ZG001 001 002 003 004 005 007 008 009 010 011 012 013 015
CONTROL CARD CAPACITOR UNIT FUSE BOX + NUT RECTIFICATION UNIT SI SIGNAL LAMP YELLOW CONTACTOR CHOKE COOLING FAN FLIP-FLOP SWITCH SWITCH TRANSFORMER AUXIL. TRANSFORMER MACHINE SOCKET RC PROTECTION UNDERCARRIAGE FRONT PLATE REAR PLATE SIDE PLATE LEFT SIDE PLATE RIGHT CLAMP INSULAT. PLATE FOR COVER PLATE REAR GRATE WHEEL WHEEL, ROTATING PLASTIC HANDLE AXLE INSULATION CIRCUIT DIAGRAM
3144530/1921760
Pc. A001 KWELD3200-4000W KEMPOMAT 2001, 2501
MASTER 1500/2200 WITH PILOT LAMP KMAT 2501 DIX BE 50/70 KEMPOMAT, KEMPOWELD KEMPOWELD 2501 KEMPOWELD 2501 KEMPOWELD 2501 KEMPOWELD 2501 D30 CLAMP KEMPOWELD MASTER 2800/3500
26X50X217/188 KEMPOWELD 2501
1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1
KEMPOWELD 3200
7.3.2000/V215303
Order no.
Part
Description
4279480 9772551 4287570 4287420 9775729 9764130 3138510 9544214 4287840 4266150 9761225 976052101 2066190 3141290 9771530 4191441 2070060 2070820 2070790 2070800 2070810 3001873 3001875 1028120 2061410 9547105 9547770 3138950 4279940 2062900 3139040
A001 F001 G001 G002 H001 K001 L001 M001 R001 R002 S001 S002 T001 T002 X003 ZG001 001 002 003 004 005 007 008 009 010 011 012 015 016 017
CONTROL CARD FUSE BOX + NUT RECTIFICATION UNIT PARALLEL DIODE SIGNAL LAMP YELLOW CONTACTOR CHOKE COOLING FAN RESISTOR SHUNT RESISTOR FLIP-FLOP SWITCH SWITCH TRANSFORMER AUXIL. TRANSFORMER MACHINE SOCKET RC PROTECTION UNDERCARRIAGE FRONT PLATE REAR PLATE SIDE PLATE LEFT SIDE PLATE RIGHT CLAMP INSULAT. PLATE FOR COVER PLATE REAR GRATE WHEEL WH WHEEL, ROTATING AX AXLE INSULATION FLAT CABLE PLASTIC HANDLE CIRCUIT DIAGRAM
3145130/1921830
Pc. A001 KWELD3200-4000W KWELD3200/4000/4000W KEMPOWELD
KWELD,KMAT 3200 MASTER 2800/3500 0.23 OHM KWELD 300A/60MV WITH PILOT LAMP D22,5 KWELD,KMAT 3200 DIX BE 50/70 KEMPOMAT, KEMPOWELD KEMPOWELD 3200 KEMPOWELD 3200/4000 KEMPOWELD 3200, 4000 KEMPOWELD 3200, 4000 D30 CLAMP KEMPOWELD MASTER 2800/3500
L=380 26X50X217/188 KEMPOWELD 3200
1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1
KEMPOWELD 3200W
7. 7 .3.2000/V216302
Order no.
Part
Description
4279480 4279500 9755223 9772551 9772551 4287570 4287420 9775729 9775731 9775729 9764130 3138510 9544214 3138320 9540410 4287840 4266150 9753587 9761225 976052101 9761221 9761622 2066190 3141290 9771530 4191441 2066280 9547105 9547771 2061410 2069250 3001873 3001875 3138950 4279940 2062900 3144940 3144950 1028360 1028370 1028350 9592126 9370162 9373216 4278740 9373215 4279930 4279920 9568956 9568957 9761302 9885031 9885032 3142290
A001 A002 C001 F001 F002 G001 G002 H001 H003 H004 K001 L001 M001 M002 M002 R001 R002 R004 S001 S002 S004 S005 T001 T002 X003 ZG001 010 030 040 050 055 060 070 100 110 145 140 150 160 170 180 190 200 210 220 230 240 250 260 270 290 300 310 320
CONTROL CARD CONTROL CARD CAPACITOR FUSE BOX + NUT FUSE BOX + NUT RECTIFICATION UNIT PARALLEL DIODE SIGNAL LAMP YELLOW SIGNAL LAMP RED SIGNAL LAMP YELLOW CONTACTOR CHOKE COOLING FAN PUMP-MOTOR COMB. PUMP-MOTOR RESISTOR SHUNT RESISTOR PTC RESISTOR +60 C FLIP-FLOP SWITCH SWITCH FLIP-FLOP SWITCH PRESSURE SWITCH TRANSFORMER AUXIL. TRANSFORMER MACHINE SOCKET RC PROTECTION UNDERCARRIAGE WHEEL WHEEL T-50 REAR GRATE INSUL. F COOLING FAN CLAMP INSULAT. PLATE FOR AXLE INSULATION FLAT CABLE PLASTIC HANDLE SIDE PLATE LEFT SIDE PLATE RIGHT COVER PLATE FRONT PLATE REAR PLATE WATER TANK PA-HOSE BLUE RUBBER HOSE WATER HOSE RUBBER HOSE HOSE CONNECTOR HOSE CONNECTOR IN-LINE CONNECTOR BRANCH CONNECTOR PROTECTION STICKER, GREEN STICKER, RED CIRCUIT DIAGRAM
3145150/1921850
Pc. A001 KWELD3200-4000 A002 KWELD 4000W 8UF/450V AC
KWELD3200/4000/4000 KEMPOWELD
KWELD,KMAT 3200 MASTER 2800/3500 SIMACO 0.23 OHM KWELD 300A/60MV WITH PILOT LAMP D22,5 WITH PILOT LAMP KWELD,KMAT 3200 DIX BE 50/70 KWELD,KMAT3200/4000 LHPL 200 PK MASTER 2800/3500 D30 CLAMP L=380 26X50X217/188 KWELD 3200W,4000W KWELD 3200W,4000W KWELD 3200W,4000W KEMPOWELD 3200W KWELD 3200W,4000W 8/6 13 MM KW 4000W 10/17 MM R1/8 - 9.5 KL R1/8 - 6 ML 2060-1/4 SWITCHES'LEVER
KEMPOWELD 3200W
1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 2 1 1 1 1 2 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 0,52 0,7 1 0,3 1 1 1 1 2 1 1 1
KEMPOWELD 4000/4000W
7.3.2000/V215304
Order no.
Part
Description
4279480 9772551 4287570 4287420 9775729 9775730 3138540 9544214 4287840 4266150 9771530 4191441 2070060 9547105 9547770 2061410 3001873 3001875 3138950 4279940 2062900
A001 F001 G001 G002 H001 H002 L001 M001 R001 R002 X003 ZG001 0-010 0-030 00-040 0-050 0-060 0-070 0-100 0-110 0-145
9764160 9760615 9760616 2066180
1K001 1S001 1S002 1T001
9764130 976051501 976052101 2066170
2K001 2S001 2S002 2T001
9764160 9760615 9760616 2066180
3K001 3S001 3S002 3T001
9764130 976051501 976052101 2066170
4K001 4S001 4S002 4T001
3144940 3144950 1028360 1028340 1028350 9592126 9370162 9373216 4278740 9373215 4279930 4279920 9568956 9568957 9581007 9761302 9885031 9885032
5-140 5-150 5-160 5-170 5-180 5-190 5-200 5-210 5-220 5-230 5-240 5-250 5-260 5-270 5-280 5-290 5-300 5-310
CONTROL CARD FUSE BOX + NUT RECTIFICATION UNIT PARALLEL DIODE SIGNAL LAMP YELLOW SIGNAL LAMP GREEN CHOKE COOLING FAN RESISTOR SHUNT RESISTOR MACHINE SOCKET RC PROTECTION UNDERCARRIAGE WHEEL WHEEL, ROTATING REAR GRATE CLAMP INSULAT. PLATE FOR AXLE INSULATION FL FLAT CABLE PLASTIC HANDLE ***K ***KE EMPOW MPOWEL ELD D 4000 4000W W CONTACTOR SWITCH 32A SWITCH 32A TRANSFORMER ***K ***KE EMPOW MPOWEL ELD D 4000 4000W W CONTACTOR Y/D-SWITCH SWITCH TRANSFORMER ***K **KEMPOWELD 4000 CONTACTOR SWITCH 32A SWITCH 32A TRANSFORMER ***K **KEMPOWELD 4000 CONTACTOR Y/D-SWITCH SWITCH TRANSFORMER ***K ***KEM EMPO POWE WELD LD 4000 4000W W SIDE PLATE LEFT SIDE PLATE RIGHT COVER PLATE FRONT PLATE REAR PLATE WATER TANK PA-HOSE BLUE RUBBER HOSE WATER HOSE RUBBER HOSE HOSE CONNECTOR HOSE CONNECTOR IN-LINE CONNECTOR BRANCH CONNECTOR HEAT EXCHANGER PROTECTION STICKER, GREEN STICKER, RED
3145140/1921840
Pc. A001 KWELD3200-4000W KWELD3200/4000/4000W KEMPOWELD
KWELD,KMAT 4000 MASTER 2800/3500 0.23 OHM KWELD 300A/60MV DIX BE 50/70 KEMPOMAT, KEMPOWELD
MASTER 2800/3500 D30 CLAMP L=380 26X50X217/188 230V 230V** **** **** ** O-Y- D K60/10 D22.5 230V K-WELD 4000 400V 400V** **** **** **
D22,5 400V K-WELD 4000 230V**** ***** O-Y- D K60/10 D22.5 230V K-WELD 4000 400V**** *****
D22,5 400V K-WELD 4000 230/ 230/40 400V 0V** **** KWELD 3200W,4000W KWELD 3200W,4000W KWELD 3200W,4000W KEMPOWELD 4000W KWELD 3200W,4000W 8/6 13 MM KW 4000W 10/17 MM R1/8 - 9.5 KL R1/8 - 6 ML 2060-1/4 140X179 SIMACO SWITCHES'LEVER
1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 0,52 0,7 1 0,3 1 1 1 1 1 2 1 1
KEMPOWELD 4000/4000W
7.3.2000/V215304
Order no.
Part
Description
3139060 4279500 9755223 9772551 9775731 9775729 3138320 9540410 9753587 9761221 9761622 3141300
5-320 5A002 5C001 5F002 5H003 5H004 5M002 5M002 5R004 5S004 5S 5S005 5T002
CIRCUIT DIAGRAM CONTROL CARD CAPACITOR FU F USE BOX + NUT SIGNAL LAMP RED SI SIGNAL LAMP YELLOW PUMP-MOTOR COMB. PUMP-MOTOR PTC RESISTOR +60 C FLIP-FLOP SWITCH PRESSURE SWITCH AUXIL. TRANSFORMER ***K **KEMPOWELD 4000 SIDE PLATE LEFT SIDE PLATE RIGHT COVER PLATE FRONT PLATE REAR PLATE CIRCUIT DIAGRAM AUXIL. TRANSFORMER
2070800 2070810 1028120 2070780 2070790 3139050 3141290
6-140 6-150 6-160 6-170 6-180 6-190 6T002
3145140/1921840
Pc. KEMPOWELD 4000W A002 KWELD 4000W 8UF/450V AC
SIMACO
WITH PILOT LAMP
230/400V*** KEMPOWELD 3200, 4000 KEMPOWELD 3200, 4000 KEMPOWELD KEMPOWELD 4000 KEMPOWELD 3200/4000 KEMPOWELD 4000
1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1
KEMPOWELD 5500W Order no. 4279480 4279500 4287250 9755223 9755177 9772551 9772551 9750175 4287420 9775729 9775730 9775731 9775729 9764160 3142030 9544262 9540410 3138320 4286970 4286540 4282710 9760615 9760616 9761221 9761622 2068950 3141300 9771540 6185666 1027740 1027750 1027710 1027730 1027770 3001873 3001875 9592158 4281090 9592126 9547150 9547711 1027050 1026960 3138950 9373215 9568903 4286530 4279930 9540415 9551058 9568956 9568938 9568957 9581006 4280650 3142130 9592136 9761302 9772523 9772526
Part A001 A002 A003 C002 C001 F001 F002 G001 G002 H001 H002 H003 H004 K001 L001 M001 M002 M002 R001 R002 R004 S001 S002 S004 S005 T001 T002 X003 005 010 020 030 040 050 060 070 080 090 100 110 120 130 140 150 160 170 180 190 195 200 210 220 240 260 270
6.08.2001/V216501
2068970/1921690
Description CONTROL CARD CONTROL CARD PTC PROTECTION CARD CAPACITOR CAPACITOR FUSE BOX + NUT FUSE BOX + NUT RECTIFICATION UNIT PARALLEL DIODE SIGNAL LAMP YELLOW SIGNAL LAMP GREEN SIGNAL LAMP RED SIGNAL LAMP YELLOW CONTACTOR CHOKE COOLING FAN PUMP-MOTOR PUMP-MOTOR COMB. RESISTOR SHUNT RESISTOR PTC RESISTOR SWITCH 32A SWITCH 32A FLIP-FLOP SWITCH PRESSURE SWITCH TRANSFORMER AUXIL. TRANSFORMER MACHINE SOCKET VOLT/AMP. METER. UNI SIDE PLATE RIGHT SIDE PLATE LEFT COVER PLATE FRONT PLATE REAR PLATE CLAMP INSULAT. PLATE FOR COOLING FAN HOLDER HANDLE PIPE WATER TANK WHEEL WHEEL, ROTATING LEFT PULL-HANDLE RIGHT PULL-HANDLE AXLE INSULATION RUBBER HOSE FEMALE FAST WATER HOSE HOSE CONNECTOR REPAIR SET FOR PUMP L CONNECTION IN-LINE CONNECTOR HOSE CONNECTOR BRANCH CONNECTOR HEAT EXCHANGER SWITCH PROTECTION CIRCUIT DIAGRAM FILTER PROTECTION FUSE 4A DELAYED FUSE 8A DELAYD
Pc. A001 KWELD3200-4000W A002 KWELD 4000W K-WELD 5500W 8UF/450V AC 4UF/400VAC
KEMPOWELD
K-WELD 5500W
SIMACO 0.23 OHM KWELD5500W 300A/60MV KWELD5500W O-Y- D K60/10 D22.5 WITH PILOT LAMP KWELD 5500W 70 MM2 MSD 1 KWELD 5500W KWELD 5500W KEMPOWELD 5500W KEMPOWELD 5500W KEMPOWELD 5500W D30 CLAMP KMIG 4000, 3200
10/17 MM CONNECTION 1/8 R1/8 - 9.5 KL SIMACO 2020-R1/4-R1/4 R1/4-12 2060-1/4
KEMPOWELD 5500W SWITCHES'LEVER 5X20 5 X 20
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 0,92 2 2 1 1 1 1 2 1 1 1 1 1 2 1 1
7.11.2002/V217201
WIRE 200 Order no. 4279550 4280180 9754156 9754141 9761375 9770450 9770117 9770458 9770460 9770460 9771591 956300201 3144220 1921650 2062070 3133500 4267970 4265820 4270940 9425216 206652001 9549064 9549066 2062900 206653001 9568911 4290570 4296860 4296210 4279770 4280040 4280050 1026870 4279940 3134270 6219200 3135870 9840352
Part A001 C001 RW101 RW102 S001 XW002 XW101 XW102 XW103 XW104 X001 Y001 0-000 0-010 0-020 0-030 0-040 0-050 0-060 0-070 0-080 0-090 0-100 0-110 0-120 0-130 0-140 0-150 0-160 0-170 0-190 0-200 0-220 0-260 0-280 1-020 2-010 2-030
3144540/1921770
Description CARD CAPACITOR POTENTIOMETER POTENTIOMETER LEVER SWITCH FEMALE CONTACT BODY MACHINE SOCKET PLUG 6 POLES PLUG 15 POLES PLUG 15 POLES MACHINE SOCKET SOLENOID VALVE CIRCUIT DIAGRAM SPARE PART LIST HUB FOR WIRE REEL CLAMP BRAKE PIECE CLAMPING NUT PRESS SPRING WASHER DOOR PLATE SLIDE LOCK CLAMP PLASTIC HANDLE SIDE PLATE HOSE CONNECTOR GUIDANCE STICKER STICKER FOR PANEL STICKER WIRE FEED STICKER KEMPOWELD CONNEC. STICKER F GAS BOTTLE SAFETY FRAME F DISPL FLAT CABLE HOSE CONNECTOR ***ACCESSORIES**** TIMER UNIT LIFT HOOK PLASTIC BAG
Pc. A001 WIRE, KEMPOMAT 0.1 UF / 250V 100 KOHM CERMET 10 KOHM CERMET 2 POLES 10 POLES, MALE
70 MALE WIRE 200 SL-K250 PROMIG PROMIG PROMIG 501, 511 M16 PROMIG D16
26X50X217/188 R1/8-5ML WIRE 200 WIRE 200, KMAT 2001, KEMPOWELD WIRE WIRE WIRE
L=380 R1/8-M12 KMW TIMER PROMIG
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1
7.11.2002/V217401
WIRE 400 Order no.
Part
4279550 4280180 9754156 9754141 9761375 9770450 9770117 9770458 9770460 9770460 9771591 9563002 3139080 1921600 2062070 3133500 4267970 4265820 4270940 9425216 2066520 9549064 9549066 2062900 2066530 9568911 3139410 3139100 4296210 4279770 4280040 4280050 4296870 1026870 1026880 3138810 3139110 4279940 3116880 3134270
A001 C001 RW101 RW102 S001 XW002 XW101 XW102 XW103 XW104 X001 Y001 0-000 0-010 0-020 0-030 0-040 0-050 0-060 0-070 0-080 0-090 0-100 0-110 0-120 0-130 0-140 0-150 0-160 0-170 0-190 0-200 0-210 0-220 0-230 0-240 0-250 0-260 0-270 0-280
6219100 6219200 3135870 9840352
1-010 1-020 2-010 2-030
2066790/1921560
Description CARD CAPACITOR POTENTIOMETER POTENTIOMETER LEVER SWITCH FEMALE CONTACT BODY MACHINE SOCKET PLUG 6 POLES PLUG 15 POLES PLUG 15 POLES MACHINE SOCKET SOLENOID VALVE CIRCUIT DIAGRAM SPARE PART LIST HUB FOR WIRE REEL CLAMP BRAKE PIECE CLAMPING NUT PRESS SPRING WASHER DOOR PLATE SLIDE LOCK CLAMP PLASTIC HANDLE SIDE PLATE HOSE CONNECTOR WIRE PATH-WELD.STICK STICKER FOR K400 STICKER WIRE FEED STICKER KEMPOWELD CONNEC. STICKER F GAS BOTTLE STICKER SAFETY FRAME F DISPL COVER PLATE FOR DISP LEFT HINGE RIGHT HINGE FLAT CABLE HOOK HOSE CONNECTOR ***ACCESSORIES**** SYNCHRONIZAT. UNIT TIMER UNIT LIFT HOOK PLASTIC BAG
Pc. A001 WIRE, KEMPOMAT 0.1 UF / 250V 100 KOHM CERMET 10 KOHM CERMET 2 POLES 10 POLES, MALE
70 MALE WIRE 400 SL-K400 PROMIG PROMIG PROMIG 501, 511 M16 PROMIG D16 WIRE 400, 550
26X50X217/188 WIRE 400, 550 R1/8-5ML K400 KEMPOWELD WIRE WIRE WIRE KMW SYNC
L=380 R1/8-M12 KMW SYNC KMW TIMER PROMIG
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1
7.11.2002/V217501
WIRE 550 Order no. 4279550 4280180 9754156 9754141 9761375 9770450 9770117 9770458 9770460 9770460 9771591 9563002 3142370 6219200 1921700 2062070 3133500 4267970 4265820 4270940 9425216 2066520 9549064 9549066 2062900 2066530 9568911 3139410 3139100 4296210 4279770 4280040 4280050 4296870 1026870 1026880 3138810 3139110 4279940 3116880 3134270 6219100 3135870
Part A001 C001 RW101 RW102 S001 XW002 XW101 XW102 XW103 XW104 X001 Y001 000 005 010 020 030 040 050 060 070 080 090 100 110 120 130 140 150 160 170 190 200 210 220 230 240 250 260 270 280
2069120/1921701
Description CARD CAPACITOR POTENTIOMETER POTENTIOMETER LEVER SWITCH FEMALE CONTACT BODY MACHINE SOCKET PLUG 6 POLES PLUG 15 POLES PLUG 15 POLES MACHINE SOCKET SOLENOID VALVE CIRCUIT DIAGRAM TIMER UNIT SPARE PART LIST HUB FOR WIRE REEL CLAMP BRAKE PIECE CLAMPING NUT PRESS SPRING WASHER DOOR PLATE SLIDE LOCK CLAMP PLASTIC HANDLE SIDE PLATE HOSE CONNECTOR WIRE PATH-WELD.STICK STICKER FOR K400 STICKER WIRE FEED STICKER KEMPOWELD CONNEC. STICKER F GAS BOTTLE STICKER SAFETY FRAME F DISPL COVER PLATE FOR DISP LEFT HINGE RIGHT HINGE FLAT CABLE HOOK HOSE CONNECTOR ***ACCESSORIES**** SYNCHRONIZAT. UNIT LIFT HOOK
Pc. A001 WIRE, KEMPOMAT 0.1 UF / 250V 100 KOHM CERMET 10 KOHM CERMET
R1/8-M12
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1
KMW SYNC PROMIG
1 1
2 POLES 10 POLES, MALE
70 MALE WIRE 550 KMW TIMER SL-K550 PROMIG PROMIG PROMIG 501, 511 M16 PROMIG D16 WIRE 400, 550
26X50X217/188 WIRE 400, 550 R1/8-5ML K400 KEMPOWELD WIRE WIRE WIRE KMW SYNC
L=380
