JRM-AP-ENG-3700 R1.pdf

J. Ray Ray McDe McDermo rmott tt – Asia Pacifi Pacific c Engin eeri eering ng

ENGINEERING PROCEDURE LEVEL 2

MATERIAL TAKE-OFF JRM-AP-ENG-3700

Page S M

J. Ray McDermot t Asia Pacifi c Engineering

Procedure number

Procedure title

Rev No.

JRM-AP-ENG-3700

Material Take-Off

1

3 of 22 Date

31/03/06

REVISION INDEX

REV NO.

REVISION DATE

0

23/11/01

Initial Issue

1

31/03/06

General Revision

AFFECTED SECTION

PREPARED BY

S. Respatie E. Kosasih / Asril

AUTHORISED BY ENG. MANAGER ENG. DIRECTOR JKT SING

CK Mohan Handoko

QA

A. Pollack S. Kumar

S. Banerjee

M. Wilson

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1

4 of 22 Date

31/03/06

TABLE OF CONTENTS

REVISION INDEX.....................................................................................................................3 1 INTRODUCTION & SCOPE .............................................................................5 2 OBJECTIVES .....................................................................................................5 3 REFERENCES....................................................................................................6 4 DEFINITIONS / ABBREVIATIONS.................................................................6 5 RESPONSIBILITIES..........................................................................................7 6 PROCESSES.......................................................................................................8 7 INTERFACES...................................................................................................15 8 DOCUMENT HANDLING AND ARCHIVING.............................................15 FLOWCHART 3701 – Work Overview APPENDIX A – Sample Bid MTO Format APPENDIX B – Sample Project MTO Format

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

1

Rev No.

1

5 of 22 Date

31/03/06

INTRODUCTION & SCOPE This document is a Level II procedure for J. Ray McDermott Asia Pacific Engineering (JRMAPE), and forms part of the management system as described in the J. Ray McDermott Asia Pacific (JRMAP) Level I Management System Manual. This Level II standard operating procedure outlines material take-off functions as applied to projects undertaken by JRMAPE.

2

OBJECTIVES a)

The objectives of this procedure is to define the responsibilities, activities and functions involved in the Material Take-Off, to be used by JRMAPE in performance of work on a project and during bid stage.

b)

Ensure that the all components/items required for the project are identified, tagged, categorised and totalled up during the engineering phase, so that they are included in the preparation of materials requisitions and purchase orders, in accordance with the overall project requirements.

c)

Ensure that work meets the following conditions: •

•

•

Accurate and adhere to all applicable governing codes and regulations and Customer specifications Be carried out systematically in accordance with the approved basis of design criteria and Customer specifications Contain adequate information so that the Customer can readily use for preparing material requisitions/ purchase orders

This procedure is subject to audit as part of the ongoing review of the management system. It is not the intent of JRMAPE to vary these processes for projects unless contractual reasons dictate otherwise. In those instances, any contractually agreed changes are outlined in the Project Execution Plan.

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

3

4

Rev No.

1

6 of 22 Date

31/03/06

REFERENCES a)

17-01-001, Level I Procedure Management System Manual – J. Ray McDermott Asia Pacific

b)

JRM-AP-ENG-0100, Organisation & Responsibilities

c)

JRM-AP-ENG-1700, Document Control

d)

JRM-AP-ENG-1800, Document Review & Verification

e)

JRM-AP-ENG-1900, Document Initiation, Signoff & Retention

f)

JRM-AP-ENG-2300, Interface Control

g)

Level II procedures, as applicable

DEFINITIONS / AB BREVIATIONS AFC

Approved For Construction

AFD

Approved For Design

BOM

Bill of Materials

Bid Take-Off

Take-off performed during bid stage

Final Take-Off

Take-off performed on AFC Design Drawings

IFA

Issued For Approval

Intermediate Take-Off

Take-off performed on IFA / AFD / AFC system Design Drawings

JRMAP

J. Ray McDermott Asia Pacific

JRMAPE

J. Ray McDermott Asia Pacific Engineering

MTO

Material Take-Off

Preliminary Take-Off

Take-off performed on IFA Design Drawings

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

5

Rev No.

1

7 of 22 Date

31/03/06

RESPONSIBILITIES a)

Discipline Designer The assigned Discipline Designer is responsible to calculating the take-offs for the respective Discipline. Discipline Designer ensures that: •

•

Prepare sketches when information is not available

•

Specifications are input and checked

•

•

b)

All relevant information is available before proceeding to perform take-off

Material groupings are established in accordance with the project requirements The take-off is complete, accurate and in accordance with the project requirements.

Discipline Drafting Squad Leader The Discipline Drafting Squad Leader is responsible for designating the Discipline Designer to carryout the MTO, provide all input information and drawings to the Discipline Designer. He/she shall also ensure that all drawings have been identified suitable for takeoff purposes and the MTO’s are checked before issue.

c)

Discipline Drafting Supervisor / Section Leader The Discipline Drafting Supervisor / Section Leader is responsible to provide relevant input information as detailed in Section 6.2 of this procedure to ensure the take-off meets the intended output requirements of the Discipline Drafting Group. He/she shall approve all Material Take-Off (MTO) documents.

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

d)

Rev No.

1

8 of 22 Date

31/03/06

Discipline Engineer The assigned Discipline Engineer is responsible to provide relevant input information as detailed in Section 6.2 of this procedure to ensure the take-off meets the intended output requirements of the appropriate Drafting Group and check the part descriptions and specifications of the Material Take-Off (MTO) document.

6

PROCESSES The Material Take-Off process involves the determination of the total quantities of various components/items, required for a project, through planning, data collection, systematic mark-up and extraction and proper reporting and thorough review. The activities involved in the development of material take-off are detailed in Flowchart 3701 and elaborated in the following sections.

6.1

PLANNING At the commencement of a project, the Drafting Squad Leader will assign a Discipline Designer, who will be the focal point for all project MTO activities within the Group. MTO’s are prepared and issued in the following categories namely: a) Preliminary – Preliminary MTO is used by Purchasing Division to source Vendor’s quotations. b) Intermediate – Intermediate MTO is used by Purchasing Division for placing Purchase Orders. c) Final – MTO is used by Purchasing Division to confirm the quantities indicated on the Purchase Orders. The final MTO will be prepared by Fabrication Yard. d) Bid MTO – MTO is used by Purchasing Division for material costing and by Fabrication Yard for fabrication manhour estimate Prior to the commencement of any take-off activity, a MTO issue schedule is planned in accordance with the drawing issue and material delivery

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1

9 of 22 Date

31/03/06

schedules, furnished by Discipline Drafting Supervisor / Section Leader and Project Engineer, respectively. Based on this information, the schedules for preliminary and intermediate material take-offs are then defined and agreed by the project team and approved by the Project Engineer. Discipline Drafting Supervisor / Section Leader and Discipline Drafting Squad Leader shall set up the planning, prepare lists of required information and drawings and monitor the preparation of Material TakeOff. When an agreed schedule cannot be met, the appropriate Discipline Drafting Supervisor / Section Leader must be informed. The Project Engineer reviews the consequences and establishes the most favorable schedule that can be achieved.

6.2

REQUISITE INFORMATION 6.2.1 Prelimi nary MTO Preliminary MTO for each Discipline Drafting Group is done based on the project specifications, drawings and documents as specified in the table below: Document Description

Source Piping

Approved Piping Specifications

Mechanical Engineering

List of long-delivery bulk material


IFA P&ID’s

Piping Drafting

Preliminary Equipment Arrangement Drawings

Piping Drafting

Material grouping breakdown

Project Engineer Electrical

Approved Electrical Specifications

Electrical Engineering

Preliminary Supplier List




IFA Electrical One-Line Diagrams

Electrical Drafting

IFA Cable Schedule

Electrical Drafting

IFA Hazardous Area Classification Drawings

Electrical Drafting

IFA Electrical Plan

Electrical Drafting

IFA Electrical Detail

Electrical Drafting

IFA Switchgear/ Control Building Equipment

Electrical Drafting

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1

Document Description

10 of 22 Date

31/03/06

Source

Arrangement Drawings IFA Equipment Arrangement Drawings

Piping Drafting


Project Engineer Instrument

Approved Instrument Specifications

Instrument Engineering



IFA P&IDs

Piping Drafting

IFA Instrument Hookups Drawings

Instrument Drafting

IFA Instrument Plan Drawings

Instrument Drafting


Project Engineer Structural (*)

Approved Structural Material Specifications

Structural Engineering

IFA Main Steel Structural Drawings


(*) Structural MTO is performed by JRMAP Fabrication Yard

6.2.2 Intermediate MTO Intermediate MTO is used by Purchasing Division to purchase the materials. The information required to perform an Intermediate MTO for each Discipline Drafting Group is tabulated below: Document Description

Supplier Piping

Approved Specifications and AFD / AFC drawings as defined in Section 6.2.1, Piping

See Section 6.2.1, Piping

IFA Piping Plans and Sections Drawings

Piping Drafting

Electrical

Approved Specifications and AFD / AFC drawings defined in Section 6.2.1, Electrical

See Section 6.2.1, Electrical

IFA / AFC Electrical Plan

Electrical Drafting

IFA / AFC Electrical Detail Drawings

Electrical Drafting

IFA / AFC Cable Schedule Drawings

Electrical Drafting

AFD / AFC Hazardous Area Classification

Electrical Drafting

AFD / AFC One Line Diagram

Electrical Drafting Instrument

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1


Supplier

Approved Specifications and AFD / AFC drawings defined in Section 6.2.1, Instruments

See Section 6.2.1, Instruments

IFA / AFC Instrument Drawings

Instrument Drafting

IFA / AFC Instrument Hookups Drawings

Instrument Drafting

11 of 22 Date

31/03/06

Structural (*)

Approved Structural Material Specifications


AFD / AFC Primary & Secondary Steel Structural Drawings

Structural Drafting


6.2.3 Bid MTO Bid MTO for each Discipline Drafting Group is done based on the bid specifications, drawings and documents as specified in the table below: Document Description

Source Piping

Piping Specifications




P&ID’s

Piping Drafting

Equipment Arrangement Drawings

Piping Drafting


Project Engineer Electrical

Electrical Specifications


Preliminary Supplier List




Electrical One-Line Diagrams

Electrical Drafting

Electrical and Instrument Cable Block Diagrams

Electrical Drafting

Hazardous Area Classification Drawings

Electrical Drafting

Switchgear/ Control Building Equipment Arrangement Drawings

Electrical Drafting

Equipment Arrangement Drawings

Piping Drafting


Project Engineer Instrument

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1

12 of 22 Date

31/03/06


Source

Instrument Specifications




P&IDs

Piping Drafting

Standard Instrument Hookups Drawings

Instrument Drafting


Project Engineer Structural (*)

Structural Material Specifications


Main Steel Structural Drawings



6.3

MTO PREPARATION Before commencement of any MTO activity, the Discipline Drafting Squad Leader reviews and compiles all relevant information and checks the revision status of drawings and specifications received in accordance with Section 6.2 above, regarding take-off status. He notifies the all the concerned Disciplines/Supplier of any missing information. The Discipline Drafting Squad Leader designates a Discipline Designer as MTO Lead and initiates the process of a take-off upon confirmation of the status of all information received and in accordance with the agreed schedule. Piping, Electrical and Instrument MTO’s are done by the respective Discipline Drafting Group MTO Leads. Discipline Designer then proceeds with the take-off in accordance with the drawings and specifications. The Discipline Designer is responsible for identifying, tagging, grouping and calculating the quantity required of each component/item. All drawings used for MTO’s shall be stamped “For MTO purpose”, and all piece marking is done on this drawing. These drawings are retained for reference. Once the MTO is complete, the data is tabulated using a computer for ease of handling and subsequent compilation.

6.3.1 MTO Reporting Typical MTO format is enclosed in Appendix-A. All MTO’s will be prepared and submitted in this format. To facilitate traceability, all MTOs shall be submitted with clear identification of the following:

Page S M


Procedure number

Procedure title

Rev No.

JRM-AP-ENG-3700

Material Take-Off

1

a)

Category of MTO (preliminary, intermediate or bid)

b)

Reference to specifications and drawing numbers

c)

Remarks for the changes

13 of 22 Date

31/03/06

6.3.2 MTO Checki ng Following preparation of MTO, the Discipline Drafting Squad Leader checks the accuracy of the completed MTO in accordance with the following main MTO checklist requirements: a)

Piping Discipline • • •

b)

Electrical Discipline • • • •

c)

Piping specification check Part description check Pipes, valves, and fittings take-off check

Electrical specification check Part description check Cable length take-off check Junction box, glands, conduit, and fittings take-off check

Instrument Discipline • • •

Instrument specification check Part description check Instrument valves, tubing, and fittings take-off check

Upon completion of checking against the specification, drawings and check lists, Discipline Drafting Squad Leader shall issue the MTO to the assigned Discipline Engineer for verification of specifications and description of the items.

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

Rev No.

1

14 of 22 Date

31/03/06

6.3.3 MTO Revisions An update to the take-off is required whenever specifications and/or drawings are revised. The Discipline Drafting Squad Leader initiates the MTO update whenever the revised information is available. The Discipline Drafting Squad Leader reviews the revised contents and issues necessary instructions to the Discipline Designer to proceed with take-off update in accordance with Section 6.3. The completed MTO update is checked in accordance with Section 6.3.2 and approved by Discipline Drafting Supervisor / Section Leader. The revision numbers for Bid MTOs should be as per JRMAPE Document Initiation, Sign-off & Retention Procedure No. JRM-APENG-1900. The revision numbers for Project MTOs should be as per Customer Document Numbering Procedures or project specific procedure developed by JRMAP.

6.3.4 Review and Appr oval The MTO shall be reviewed and approved in accordance with Procedure No. JRM-AP-ENG-1800, Document Review and Verification. The Discipline Drafting Supervisor / Section Leader shall approve all MTOs.

6.3.5 MTO Issu e All MTOs will be issued in accordance with Procedure No. JRMAP-ENG-1900, Document Initiation, Signoff & Retention. The document control will be in accordance with Procedure No. JRM-AP-ENG-1700, Document Control.

6.3.6 MTO Pad The MTO pad quantity will be determined by Fabrication Yard.

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

7

Rev No.

1

15 of 22 Date

31/03/06

INTERFACES All interface control requirements will be issued in accordance with Procedure No. JRM-AP-ENG-2300, Interface Control. The Drafting Squad Leader and the Drafting Supervisor are responsible for all interfaces required in the preparation of a MTO.

8

DOCUMENT HANDLING AND ARCHIVING The Discipline Drafting Squad Leader will maintain hard and soft copies of latest revision of MTOs as well as superseded revisions and check prints during the course of the project. When a project is complete, the latest revision of the MTOs shall be stored in accordance with Procedure No. JRM-AP-ENG-0600, Project Filing Records.

Page


S M

Procedure number

Procedure title

Rev No.

JRM-AP-ENG-3700

Material Take-Off

PROJECT ENGINEER

1

LEAD DISCIPLINE ENGINEER Review & verify material specifications & groupings DISCIPLINE DRAFTING SUPERVISOR / SECTION LEADER Provide drawings DISCIPLINE DRAFTING SQUAD LEADER Review material specifications, material groupings, & drawings Provide instruction to begin take-off

Discipline Designer

Perform & update take-off

DISCIPLINE DRAFTING SQUAD LEADER Check take-off (Section 6.3.2) Yes

Changes?

No DISCIPLINE ENGINEER Yes

Issue MTO to Project Engineer / Document Control

Discipline Drafting Supervisor / Section Leader No Approval

Changes?

Date

31/03/06

Material Take-Off FLOWCHART 3701 Work Overview

Define schedule Provide material specifications Provide material groupings

Verify take-off (Section 6.3.2)

16 of 22

Page S M


Procedure number

Procedure title

Rev No.

JRM-AP-ENG-3700

Material Take-Off

APPENDIX A SAMPLE BID MTO FORMAT

1

17 of 22 Date

31/03/06

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

. D T T L . C C E J N I O " A C I R P S T " E M N N O E R D M O P F N I O T S L A L P I E P L V E D L I D A H T E P U H O L L C E L O B E N H W O T C R 5 O 1 2 N 2 R

Rev No.

F F O E K A T L G N A I I R T I E T T F A E M B U K T L U & B E T B N U E T M U R T S N I

: S E C N E R E F E R

N N O O I I T T S A A C M C N I N N I A F I L O R I O O I I I F C A T C I T G E T A A E T A I P A C E P C I S C I S D D I F F N I N F I L N G N E I T O C C O I E I E N Y S O E I C I K E K T P T P P A H E T S A S S P P D A K C C A E T K C D A L O F L N L L G L L C E O S O A E R J N G A I T N N R O T E D F E S S I O M A T C S D A E N P I P N L I I L S N P N L P U D I P G O Y I A H A E O R T T T T U C P B T O T M C T N N N L D S S N N N N N S I E E E P A A A E A A A A N M M M E E G G M L L L L & U U U L H & & U P P P P G R R R B R T T T N L T T T I L E E T T O O O O I S S S S E R R L L L P I I I S N I N I N L N U I F W F F I P P P P P ) ) ) ) 1 1 ) ) 2 0 1 1 ) ) A 1 . B . . A . A . A . D . B . U V V V V V V V V R E E E E E E E E ) ) ) ) ) H R R ( R ( D ( R ( R ( R ( R ( R . 0 . 0 . 0 . 0 . T ( 2 V V V V V 1 1 4 9 0 2 3 1 0 E E E E E 0 0 2 0 1 1 1 0 0 - 0 - R R R R R 0 - 0 - 0 - 0 - 0 - 0 - 0 L L L L L K K ( ( ( ( ( 5 6 4 4 4 4 4 4 4 1 2 3 4 5 0 - - - - - - - 0 0 0 0 0 - 0 7 7 7 7 7 7 7 0 0 0 0 0 0 4 8 8 8 8 8 8 8 0 0 0 0 0 2 8 2 2 2 2 2 2 2 - - - - - 9 9 9 7 7 7 4 - 9 - 9 - 9 - 9 - 9 - 9 - 5 7 - 4 1 1 1 1 1 1 1 4 - 0 - 0 - 0 - 0 - 8 8 0 0 0 0 0 0 0 7 6 6 6 6 0 0 5 5 5 5 5 5 5 8 7 7 7 7 5 5 4 4 4 4 4 4 4 9 9 9 9 9 4 4 8 8 8 8 8 8 8 4 4 4 4 4 8 8 - - - - - - - - - - - - -

18 of 22 Date

1

31/03/06

R ' G N E . J O R P

S D

Y B D E V O R P P A

O H K

Y B D E I F I R E V

S D / G A

N O I T P I R C S E D

D I B R O F D E U S S I Y B

R D / A A

E T A D

5 0 0 1 8 2

. V E R

A

1 2 0 F 0 9 - O T 1 . M - T H E I - S 5 1 2 2 R : . o N . c o D

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

A 5 : 0 N 0 1 O I 8 S 2 I V : E E R T A D

. G D N T I L T T . C T C E I F N J E I O " B A I R U S P C E T " T N N M & O E R E D M O B N P F U I T T S O L A P I E L L V P O T L I E D M H D A E P T K H L O U L U L B C L E T O E N B W N O H E C T M R A 5 O U 1 N R T 2 S 2 N R I

Rev No.

Date

1

31/03/06

S K R A M E R

Y T Q L A T O T

4 2

-

-

8 4

0 1 8 3

6 4 0 2

4 8

8 -

5 8 3

-

8 3

7 1 5 9 1 9 6 2 4

) M A D T A A P B Y B (

6

-

-

6

8 4 3

6 8 1

2 1

1 -

5 3

-

1 1

5 7 2 1 4 1

Y T Q

8 1

0 9 6

2 8 1 1

2 4

2 6 4 3

0 6 8 1

2 7

7 8

0 5 3

0 0 0 0 5 7 2 7 5 5 7 7 6 2 1 4

T I N U

M

M

M

M

M

M

M

A A E E

A E

A A A A A A A A E E E E E E E E

) M 6 L R ( T W " 5 3 0 . 0 , 0 0 4 L E N O M , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 8 / 3

) M 6 L R ( L 6 1 3 P T 9 6 2 M T S A T W " 5 6 0 . 0 . N I M o M % 5 . 2 / W , S S 6 1 3 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 8 / 3

) M 6 L R ( L 6 1 3 P T 9 6 2 A M T S A T W " 3 8 0 . 0 . N I M o M % 5 . 2 / W , S S 6 1 3 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 1

) M 6 L R ( T W " 5 6 0 . 0 , ) 4 5 2 1 3 S N U ( o M 6 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 2 / 1

L L A A U U Q Q E E R R O O 4 - 4 1 - 1 0 0 0 0 4 - 6 S S S S # # K K O O L L E E G G A A W W S S , , S S S S 6 6 1 1 3 3 E E L L U U R R R R E E F F E E L L B B U U O O D D . . N N N N O O C C E E L L A A M M S T T G P P N N I N " T " 4 / 4 T / I 1 1 F X X E T T B " " 4 / 8 U / T 1 3

L A U Q E R O 6 1 0 0 6 S S # K O L E G A W S , S S 6 1 3 E L U R R E F E L B U O D . N N O C E L A M T P N " 8 / 3 X T " 8 / 3


L L A L A U A U Q U Q E Q E R E R O R O 2 O 8 - 1 - 4 1 - 1 - 1 0 0 0 0 0 1 6 - 6 - 8 M S S # S S K # # O K K L O O E L L G E E A G G W A A S W W , S S L , , E S S N S S O 6 6 1 M 1 , 3 3 E E E L L L U U U R R R R R R E E E F F F E E E L L L B B B U U U O O O D D D . . . N N N N N N O O O C C C E E E L L L A A A M M M T T T P P P N " N " N " 2 / 4 / 4 / 1 3 1 X X X T " T " T " 8 / 8 / 2 / 3 3 1

L L A A U U Q Q E E R R O O 2 1 6 1 L 1 A - 0 1 - 1 L U 0 8 - A Q 1 S U E 6 1 - S Q R S # E O S K 6 - 6 # O 0 0 0 0 K L 6 6 E O G - L A S M S # E G W # K A S K O , W S O L S S L E , E G S 6 G A S 1 3 A 6 E W W 1 L S S , 3 , L E U E L R S S N R U E 6 O R F 1 R 3 M , E E E F L E L L B E U U U L R B O R R R U D E . E O N F F D N E E . L N O L B B N C U U O E O O C L D D , , E A L M N N A T O O I M P I N N T N " U U 4 E E P / N 3 B B " 1 X U U T T X T " " " T / 2 / 8 / 8 " 1 1 3 3

4 0 1 0

5 0 1 0

6 0 1 0

7 0 1 0

0 1 2 I 2 I 1 1

2 2 1 0

3 2 1 0

4 5 2 2 1 1 0 0

7 2 1 0


. O N M E T I

) M 6 L R ( L 6 1 3 P T 9 6 2 M T S ) ) M M A 6 6 T L L W R R " ( 5 ( T T 3 0 . W W 0 " . 5 " N 3 5 3 I 0 . 0 M . 0 0 o , , ) ) M 4 4 5 5 % 2 2 5 1 1 . 3 3 2 S S / N N W U , U ( ( S o o S M M 6 6 6 1 , 3 , , D D E E D L L E L A A A E E E N N N N N N A A A Y Y Y L L L L L L U U U F F F , , , S S S L L L M M M S S S , , , G G G N I N I N I B B B U U U T T T D D E D O O " " " B O 4 / 8 / 8 U / T 1 3 3

1 I 0 1 0

2 0 1 0

3 0 1 0

0 0

6 2 1 0

8 2 1 0

19 of 22

9 2 1 0

0 3 1 0

1 2 0 F 0 9 T 2 . M - T H E I 5 1 2 2 R : . o N . c o D

Page S M


Procedure number

Procedure title

Rev No.

JRM-AP-ENG-3700

Material Take-Off

APPENDIX B SAMPLE PROJECT MTO FORMAT

1

20 of 22 Date

31/03/06

Page S M


Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

T C E J . O D R " T P A L T " . C N E M N I M R O A F I P T S O A E L L N E P O V E D D D N I D A E O L H C E I L O F L N K E O A W C N A L E B

Rev No.

1

K C E K D C R E A D L R L A E L C L B E U C S - G G N I N I T T U U O O R R G G N I N I B B U U T T N N O I O I T T C C E J E J N I N I N L L O K A A K I C T E C C C A D I I E C N M M D I N F I E E N L I O A H H I A I I C C A T T C M E A P - & & M E C I S N N N T D F A A N I N A U O L L L I O C I E T P P P O P A N N N Y T S L O O O A A I I L L N L I T T T P L A G I T A A A O A S S C C C O T E N O O O L S D I L L L N I T T T T T G T N N N N N U N E E E E E L P E M M M M M E M U U U U U L U R R R R R B R T T T T T I T S S S S S S S U N I N I N I I N I N I F N : : : : : : :

F F O E K A T L G N A I I R T I E T T F A E M B U K T L U & B E T B N U E T M U R T S N I

: S E C N E R E F E R

6 4 2 2 ~ ~ ~ & 1 1 1 1 . . . . T T T T H H H H S S S S 1 2 1 2 3 4 0 0 0 0 0 0 0 0 0 0 - - 0 - 0 - 0 - 0 - 0 L L 8 8 8 8 5 4 4 4 4 4 4 - - - - - - 4 7 7 7 7 7 7 7 8 8 8 8 8 8 8 0 0 0 0 0 0 0 0 - 0 - 0 - 0 - 0 - 0 - 0 5 5 5 5 5 5 5 0 0 0 0 0 0 0 5 5 5 5 5 5 5 4 4 4 4 4 4 4 8 8 8 8 8 8 8 - - - - - - -

21 of 22 Date

31/03/06

R ' G N E . J O R P

S S M M

Y B D E V O R P P A

O O H H K K

Y B D E I F I R E V

S S D / D / K K W W


E T Y A I R D A N E I M I M R L E E T R N I P R R O O F F D D E E U U S S S I S I

Y B

R R D / D / H H A A

E T A D

2 2 0 0 0 0 2 2 / / 2 3 / / 9 1 1

. V E R

B A

1 2 0 F 0 7 O 4 - 1 . 7 T 8 H 0 3 - S 5 0 5 4 8 : . o N . c o D

Page


S M

Procedure number

Procedure title

JRM-AP-ENG-3700

Material Take-Off

B 2 : 0 0 N 2 O I 3 0 S I 9 V : E R E T A D

G N T I C T T E I J F . O E D R " B T P A U L " T . T C N M & N R E I E M B A P O F U I S O T T E L A N E L O P T O V D E D D N A M I D E K O L H L E L U C I B O F L N K E T N O A W C N E A M L U E R B T S N I

Rev No.

Date

1

31/03/06

S K R A M E R

Y T Q L A T O T

4 2

-

-

8 4

0 1 8 3

6 4 0 2

4 8

8 -

5 8 3

-

8 3

7 5 9 1 9 6 2 1 4

D A P

6

-

-

6

8 4 3

6 8 1

2 1

1 -

5 3

-

1 1

7 1 5 1 2 4

Y T Q

8 1

0 9 6

2 8 1 1

2 4

2 6 4 3

0 6 8 1

2 7

7 8

0 5 3

0 0 0 0 5 5 5 7 2 7 7 7 6 2 1 4

T I N U

M

M

M

M

M

M

M

A A E E

A E

A A A A A A A A E E E E E E E E

) M 6 L R ( T W " 5 3 0 . 0 , 0 0 4 L E N O M , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 8 / 3

) M 6 L R ( L 6 1 3 P T 9 6 2 M T S A T W " 5 6 0 . 0 . N I M o M % 5 . 2 / W , S S 6 1 3 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 8 / 3

) M 6 L R ( L 6 1 3 P T 9 6 2 A M T S A T W " 3 8 0 . 0 . N I M o M % 5 . 2 / W , S S 6 1 3 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 1

) M 6 L R ( T W " 5 6 0 . 0 , ) 4 5 2 1 3 S N U ( o M 6 , D E L A E N N A Y L L U F , S L M S , G N I B U T D O " 2 / 1

L L A A U U Q Q E E R R O O 4 - 4 1 - 1 0 0 0 0 4 6 - S S S S # # K K O O L L E E G G A A W W S S , , S S S S 6 6 1 1 3 3 E E L L U U R R R R E E F F E E L L B B U U O O D D . . N N N N O O C C E E L L A A M M S T T G P P N N " N I " T 4 / 4 / T I 1 1 F X X E T T B " " U 4 / 8 / T 1 3



L L A L A U A U Q U Q E Q E R E R O R O 2 O 8 - 1 - 4 1 - 1 - 1 0 0 0 0 0 1 6 8 - 6 - M S S # S S # # K O K K L O O E L L G E E A G G W A A S W W , S S L , , E S S N S S O 6 6 1 M 1 , 3 3 E E E L L L U U U R R R R R R E E E F F F E E E L L L B B B U U U O O O D D D . . . N N N N N N O O O C C C E E E L L L A A A M M M T T T P P P N " N " N " 2 / 4 / 4 / 1 3 1 X X X T " T " T " 8 / 8 / 2 / 3 3 1

L L A A U U Q Q E E R R O O 2 1 6 1 L 1 A - 0 1 - 1 L U 0 8 - A Q 1 S U E 6 1 - S Q R S # E O S K 6 - 6 # O 0 0 0 0 K L 6 6 E - O G S L A M S # E G W # K A S K O , W S O L S S L E , E G S 6 G A S 1 3 A 6 E W W 1 L S S , 3 , L E U E L R S S N U R 6 O R E 1 R F 3 M , E E E E F L L L B E U U U L R B O R R R U D E E . O N F F D N E E . L N O L B B N C U U O E O O C L D D , , E A L M N N A T O O I I P M N N N T " U U P 4 / E E N 3 B B " 1 X U U T T X T " " " T " 2 / 8 / 8 / 1 1 3 3

4 0 1 0

5 0 1 0

6 0 1 0

7 0 1 0

1 I 0 2 2 I 1 1

2 2 1 0

3 2 1 0

4 5 2 2 1 1 0 0

7 2 1 0


. O N M E T I

) M 6 L R ( L 6 1 3 P T 9 6 2 M T S ) ) M M A 6 6 T L L W R R " ( 5 ( T T 3 0 . W W 0 " . " 5 5 N 3 3 I 0 . 0 M . 0 0 o , , ) M 4 ) 5 4 % 2 5 5 1 2 . 3 1 2 S 3 / S N N W U U , ( ( S o o S M M 6 6 6 1 , 3 , , D D E E D L L E A A L E E A N N E N N N A A N A Y Y Y L L L L L L U U U F F F , , , S S S L L L M M M S S S , , , G G G N I N I N I B B B U U U T T T D D E D O " O " O B " 8 8 U 4 / / / T 1 3 3

1 I 0 1 0

2 0 1 0

3 0 1 0

0 0

6 2 1 0

8 2 1 0

22 of 22

9 2 1 0

0 3 1 0

1 2 0 F 0 7 O 4 - 2 . 7 T 8 H 0 3 - S 5 0 5 4 8 : . o N . c o D

JRM-AP-ENG-3700 R1.pdf

Recommend Documents