Mechanical Seal - General Installation and Maintenance Instructions for Machinery Components
Full description
Full description
Instrucciones de lubricacion
KONE KSS 280 Series Signalization Maintenance instruction
6
CONFIGURING AND TESTING KSS 280 Configure and test the signalization with the COP maintenance mode (indicated by T or C). Maintenance mode contains: – Test menu (“T”) – Configuration menu (“C”)
6.1
Tools No tools needed.
6.2
Accessing maintenance mode Step 1
Action Press DOB button and the lower / leftmost call button on the COP for ten seconds until “Spanner” icon starts to blink.
KONE KSS 280 Series Signalization Maintenance instruction
Step 2
Action Press th the lo lower/leftmost ca call bu button fo for five seconds until: – "Spanner" icon stops blinking and continues to stay on. – "--" sign appears right side of the "Spanner" icon. – "T" sign appears on the leftmost position of the indicator.
3
Press th the lo lower/leftmost ca call bu button to to toggle between Test (T) and Configuration (C) menu.
KONE KSS 280 Series Signalization Maintenance instruction
6.3
Configuring CO COP Re-configuration is necessary when: – Adding, replacing or removing components com ponents to the COP panel – Changing or adding an option opti on or floor in the system Table 5: Configuration codes Code 00 01 02
6.3. 6. 3.1 1
Name Re-configure button Re-configure COP Clear all the configuration
Description Re-configure a single button or switch Re-configure the whole COP (Side) Clear all the configurations stored in KSSLCBBx and KSSLMUL (the COP must be re-configured from scratch).
Con onfi figu gura rati tio on ove verv rvie iew w Each COP button and switch has its own ID number for elevator LON network. The signalization system identifies each COP button and switch by their individual ID number. The ID numbers of COP buttons and switches are stored in the confi guration table located on the KSSLMUL board.
KONE KSS 280 Series Signalization Maintenance instruction
6.3. 6. 3.2 2
Usin Us ing g co conf nfig igur urat atio ion n men menu u (C) (C) In configuration menu, the two digit configuration codes appear on the right side of the "Spanner" icon starting from 00. Step 1
Action Press the lower/leftmost call button shortly to increase the configuration code by one unit.
2
Press the DOB button shortly to enter the selected configuration sub-menu.
Note / Illustration Reset back to 00 when sub-menu code is greater than 02.
AS-12.20.027 (A) 2013-05-02
KONE KSS 280 Series Signalization Maintenance instruction
6.3. 6. 3.3 3
Conf Co nfig igur urin ing g CO COP P but butto ton n or sw swit itch ch
Step 1
Action In configuration sequence 00 00,, press the COP button or cycle key/toggle switch shortly: • The floor/featu floor/feature re ID (2 (2 digits) digits) is displayed on the right side of the "Spanner" icon.
Note / Illustration Pressing the COP button shortly under reconfiguration, shows the logic floor ID.
Press the COP button for one second to enter the reconfiguration mode of the button. Press/activate sh shortly th the bu button un under reconfiguration to decrease the button/ switch logic ID. Press the DOB button shortly to increase the logic ID.
The COP beeps when entering the reconfiguration mode. COP direction arrow up light lits when the ID is over 99. Arrows up and down lit when the ID is over 199.
* "A" TTC A-side floor "C" TT C C-side floor
4
Press the COP button for one second to save the new configuration and exit from the configuration sub-menu. The COP beeps when exiting.
KONE KSS 280 Series Signalization Maintenance instruction
6.3. 6. 3.4 4
Conf Co nfiigu guri ring ng CO COP P lo loca cati tion on
Step 1
Action In configuration sequence 01 01,, pressing the left/lowermost call button increases the COP Deck value. – The two digit deck value is displayed di splayed on the right side of the "Spanner" icon. – The side value (A, B, C, D) is displayed on the right side of the position indicator indi cator..
Note / Illustration Pressing the COP button shortly under reconfiguration, increases the logic floor ID.
* 00 Deck value (COP number) not configured 01 COP 1 Deck number 02 COP 2 Deck number 2
Press the DOB bu button shortly swit itc ch the COP side between A, B, C and D.
* "A" TTC A-side floor "C" TTC TT C C-side C-side floor
3
Press th the le left/lowermost ca call bu button fo for one second to save the new configuration and exit the configuration menu.
KONE KSS 280 Series Signalization Maintenance instruction
6.3. 6. 3.5 5
Clea Cl eari ring ng CO COP P con confi fig gur urat atio ion n
Clear all the configuration in KSSLCBBx and KSSLMUL (the COP must be re-configured from scratch). Step 1
6.4 6. 4
Action In configuration sequence 02,"C" starts to blink on the right side of the position indicator. Press the leftmost/lowermost call button for one second to clear the configuration.
Note / Illustration
Tes esttin ing g CO COP P an and d la land ndin ing g com ompo pone nent nts s The following tests are available. Table 7: Test codes Code 00
Description Each segment and icon in COP switches on and when pressing pressels or using key switches, COP displays the respective ID and the buzzer or speaker beeps.