Date of approval of RA 9292
April 17, 2004
There are __________ Articles and __________ sections in the RA 9292.
8, 43
Any person who shall violate any provision of RA 9292 or any rules, regulations, the Code of Ethics and the Code of Technical Standards of Practice is stated in section _________.
35
This act is was consolidation of House Bill No. 5224 and Senate Bill No. 2683.
RA 9292
The chairperson of the PRC shall include in the Commission's program the implementation of RA 9292; the funding of w/c shall be included in the Annual General Appropriation Act.
Sec 40
According to section 43, RA 9292 shall take effect __________ following its full publication in the __________ or any newspaper of general circulation.
15 days, Official Gazette
Who among the following persons was not a signatory of the 9292?
JESUS P. NAZARENO
Section 40 of RA 9292.
Appropriations
Which of the following is not true for the qualifications of Board Members of Electronics Engineering?
Be a citizen and a resident of the Philippines for 5 consecutive years prior to his appointment
All records of the Board, including applications for the examination, administrative cases involving PECE, ECE and ECTs shall be kept by
PRC
The members of the Board shall hold office for a term of __________ from date of appointment or until their successors shall have been appointed and qualified and may be re-appointed once for another term.
3 years
Section 7 states that the Board is vested with the authority to: Adopt an official __________ of the Board.
Seal
The compensation and allowances of the Board is comparable to that being received by the Chairman and members of existing regulatory boards under the Commission as provided for in the __________.
Gen Appropriations Act
Each member of the Board shall take the/a __________ prior to the assumption of office.
proper oath
How much or what fine is required for any person who shall violate any provision or any rules, regulations, the Code of Ethics and the Code of Technical Standards of Practice promulgated under RA 9292?
Not less than Php100,000.00 nor more than Php 1M or by imprisonment of not less than 6 months nor more than 6 years, or both, in the discretion of the court
The Board and the __________ shall correct and rate the licensure examination papers
Commission
According to section 2-Statement of Policy, the state shall therefore develop and nurture competent, virtuous, productive, and __________ PECE, ECE, and ECTs
well rounded
A candidate for Electronics Engineer or Electronics Technician who obtains a passing rating in the majority of the subjects but obtains a rating in the other subject/s below _________ percent but not lower than __________ percent, shall be allowed to take one removal examinations on the subject/s where he/she failed to obtain the passing rating.
70, 60
Within __________ years after the effectivity of RA 9292, the Board shall issue Certificate of Registration and Professional Identification Cards without examination to all applicants for registration as Electronics Technicians who comply to all the requirements stated in section 20.
5 (five)
With reference to prob 22, all submittals/documents shall be accompanied by a certification from __________ registered PECEs vouching for the integrity, technical capability and good moral character of the applicant.
at least 3
It is a method of managing all the activities that affect the quality of goods or services in order to prevent faults.
Quality Assurance
This type of business organization can be set up without any formality. It exists when there are a number of people involved who are part owners of the business.
Partnership
Items purchased from a vendor cost Php 20 each, and the forecast for next year's demand is 1,000 units. If it costs Php 5 every time an order is placed for more units and the storage cost is Php 4 per unit per year, what quantity should be order each time?
50 units
Two products, X and Y, both require processing time on machines I and II. Machine I has 200 hours available, and machine II has 400 hours available. Product X requires one hour on machine I and four hours on machine II. Product Y requires one hour on machine I and one hour on machine II. Each unit of product X yields PhP 10 profit and each units of Y yields PhP 5 profit. What is the Linear Programming Model for this problem.
Max Profit = PhP 10X +PhP 5Y
Subject to: X + Y 200
4X + Y 400
X, Y 0
This process can be used to measure achievement in Total Quality Management (TQM) system. Also it provides the essential control and measure feedback loop necessary for quality improvement
Benchmarking
A project has been defined to contain the following list of activities, along with their required times for completion
Activity
Time (days)
Immediate Predecessors
A
5
-
B
6
-
C
3
A
D
8
A
E
2
B,C
F
11
B,C
G
1
D
H
12
E,D
What is the completion time of the whole project?.
25 days
Here are the monthly data for the past 8 months. From these data, what are the forecasts for the following 4 months using linear regression?
Period
Actual
1
300
2
540
3
885
4
580
5
416
6
760
7
1191
8
760
9th--997, 10th- 1067.67, 11th – 1138.33, 12th – 1209
It is the process of attracting potential employees to the company so that the selection process can be carried out.
Recruitment
It is the name given to any activity undertaken by the organization with the express purpose of gaining information about potential customer
Market Research
It is used when product are made singly or in small batches. It happens when a small number of products are processed at each storage before going on to the next stage.
Job Production
It involves a voluntary association of people, called members, who operate an enterprise collectively. The aim of this organization is not to make profit but to give support to their members.
Cooperatives
It is the rational way to ensure that our limited time is always used effectively.
Time Management
A hole is to be punched out of plate having a shearing strength of 40 ksi. The compressive stress in the punch is limited to 50 ksi. Compute the maximum thickness of plate from which a hole 2.5 inches in diameter can be punched.
0.781 in
A hole is to be punched out of plate having a shearing strength of 40 ksi. The compressive stress in the punch is limited to 50 ksi. If the plate is 0.25 inches thick, determine the diameter of the smallest hole that can be punched.
0.800 in
A large pipe, called a penstock in hydraulic work, is 1.5 m in diameter. It is composed of wooden staves bound together by steel hoops, each 300 sq. Millimetre in cross-sectional area, and is used to conduct water from a reservoir to power a house. If the maximum tensile stress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30 m?
177 mm
At what angular velocity will the stress in a rotating steel ring equal to 150 MPa if its mean radius is 220 mm? The density of the steel is 7.85 Mg/m^3.
628 rad/s
A pipe carry steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate use to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 80 MPa, of which 55 MPa is the initial stress?
17
A pipe carry steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate use to cap the end. What circumferential stress is developed in the pipe?
75.3 MPa
It is the maximum safe stress that a material can carry
working stress
It is the point at which there is an appreciable elongation of the material without any corresponding increase of load
Yield point
This component measures the pulling (or pushing) action perpendicular to the section
Axial forces
A steel rod having a cross-sectional area of 300 sq. Meters and a length of 150 m is suspended vertically from one end. It supports a tensile load of 20 kN at the lower end. If the unit mass of steel is 7850 kg/m^3 and E = 200x10^3 MN/m^2, find the total elongation of the rod.
54.3 mm
What is the theoretical maximum value of Poisson's ratio of any given material subjected to a uniform triaxialstress.
1/2
A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of cast iron 5 mm thick. Compute the load that will compress the combined bar a total of 0.8 mm in the length of 2m. For steel E = 200 GPa, and for cast iron E = 100 GPa
192 kN
A solid steel shaft 5 m long is stressed to 80 MPa when twisted through 4 degrees. Using G = 83 GPa, compute the shaft diameter.
138 mm
A solid steel shaft is not to twist through more than 3 degrees in a 6 m length when subjected to a torque of 12 kN.m. What maximum shearing stress is developed? Use G=83GPa.
41.3 MPa
What is the minimum diameter of a solid steel shaft that will not twist through more than 3 degrees in a 6 m length when subjected to a torque of 12 kN.m? Use G=83GPa.
114 mm
A steel rod 2.5 m long is secured between two walls. If the load on the rod is zero at 20 degree Celsius, compute the stress when the temperature drops to -20 degrees Celsius. The cross-sectional are if the rod is 1200 sq. mm, coefficient of linear expansion = 11.7 um/(m-deg.C), and E = 200 GPa. Assume that the walls are rigid.
93.6 MPa
Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20 mm-diamter wire on a mean radius of 80 mm when tha spring is supporting a load of 2 kN. Use G = 83 GPa.
120.6 MPa
Determine the elongation in a helical steel spring composed of 20 turns of 20 mm-diamter wire on a mean radius of 80 mm when tha spring is supporting a load of 2 kN. Use G = 83 GPa.
98.7 mm
These are components of the total resistance to sliding the portion to one side of the exploratory section past the other.
Shear forces
Who first postulated that stress is proportional to strain in 1678?
Robert Hooke
It explains combustion as a result of loss of a substance.
Phlogiston
The volume of a definite quantity of dry gas is inversely proportional to the pressure provided the temperature remains constant.
Boyle's Law
It refers to matter that do not have definite form or structure.
Amorphous
Three grams of sulphur dissolved in 200 g of naphthalene C10H8, was found decreasing the freezing point of the solvent to 0.72 C. Find the molecular weight of the solute. (Kf C10H8 = 6.9 C/molar)
135.61 g/mole
It is the enthalpy change associated with the condensation of gaseous positive and negative ion into a crystal.
Lattice Energy
Substance having a pH level less than 7
Acid
It is a product of the weathering of complex silicates, particularly of feldspars which are abundant minerals.
Clay
Electrons occupy all the orbitals of a given subshell singly before pairing begins. These unpaired electrons have parallel spins. This is known as:
Hund's rule
This law states that at constant temperature the volume of a sample of gas varies inversely with the pressure.
Boyle's Law
It is the scattering of light by colloidal particles
Tyndall Effect
Consider H3AsO3, Arsenic acid (H=1.01,As=74.9,O=16.0).How many mole is 1kg of H3AsO3?
7.94 moles
It is customary to indicate accuracy by using a certain numbers of figures or digits.
significant figures
It is required for organic compounds.
Carbon
Term used to denote the technology of treating a mined ore to obtain a product higher on concentration of a wanted mineral from the unwanted rock mass in which it occurs.
ore dressing
It states that, "If a stress is placed on a system on equilibrium whereby the equilibrium is altered, that change will take place which tends to relieve or neutralize the effect of the added stress".
Le Chatelier's Principle
The energy possessed by a substance that allows it to be changed into a new substance.
Chemical energy
If heat is absorbed by the system during a chemical change, it is called as:
Endothermic
Who determined the quantitative relationship between the amount of electricity used in electrolysis and the amount of chemical reaction that occurs?
Michael Faraday
It is considered as derivatives of ammonia in which one or more of the hydrogens have been replaced by the alkyl or aryl group. It is characterized by unpleasant odors.
Amines
Calculate the molar concentration of a solution that contains 15g of potassium hydroxide in 225ml of solution.
1.2 M
Calculate the ratio of the rate of diffusion of hydrogen to the rate of diffusion of oxygen. How fast does hydrogen diffuse than oxygen? Given: Density of oxygen is 0.0899 g/L and the density of oxygen is 1.43 g/L.
Four
What is the volume of 1 moles of a gas at 2 atm and 273 K?
11.2L
It is a borosilicate glass with a very low coefficient of thermal expansion, hence, it's wide for cooking and serving utensils.
Pyrex
What is the mass in kilograms of 10.5 gal (39.7 L) of gasoline with a specific gravity of 0.82.
33 kg
It is a colorless solid capable of being cut into brilliant crystals is the hardest, must abrasive mineral known.
Diamond
It is the calculation of both energy balances and material balances in a chemical system.
Stoichiometry
_________ involves the replacement of one of the atoms or groups of atoms attached to the carbon "Backbone" of the organic molecule.
Substitution Reaction
Calculate the volume (in Litres) occupied by 7.40g of NH3 at STP (Standard Temperature, and Pressure)
9.73L
It is the Energy change accompanying a mole of electrons being added to a mole of a gaseous atoms or ions.
Electronic Affinity
A 466g sample of Water is Heated from 8.50'C to 74.60'C. Calculate the amount of Heat Absorbed (in Kilo Joules) by the Water.
129 KJ
A silicon chip used in an integrated circuit of a microcomputer has a mass of 5.68mg. How many silicon (Si) atoms are present in this chip?
1.22x1020atoms
This Law states that if a process can be written as the sum of several stepwise processes, the Enthalphy change the total process equals the sum of the Enthalphy changes of the Various Steps.
Hess Law
This process separates the components of a mixture on the basis of differences in particle size. It is used most often to separate a liquid from a solid.
Filtration
Sulfur Hexafluoride (SF6) is a colorless, odorless, very unreactive gas. Calculate the pressure (in atm) exerted by 1.82 moles of gas in a steel vessel of volume 5.43L at 45°C.
8.75 atm
It is defined as the pressure exerted by a force of one newton acting on an area of one square meter.
Pascal
A bottle of certain ceramic tile cleanser, which essentially a solution of hydrogen chloride, contains 130g of HCl and 750g of water. What is the percent by mass of HCl in this cleanser?
14.8%
A covalent bond between two atoms with different electronegativities, so that the electron density is unsymmetrically distributed.
Polar bond
Which element has the highest ionization potential of its atom?
Helium
It is the minimum amount of radioactive material needed to sustain a nuclear chain reaction.
Critical mass
In the atmosphere, nitrogen dioxide reacts with water to produce nitric acid, which contributes to pollution by acid rain: 3NO2(g) + H2O(l) -----> 2HNO3(aq) + NO(g) How many grams of HNO3 are produced for every 1.0mol of NO2 that reacts? The molecular weight of HNO3 is 63.0amu.
42 g HNO3
_________ states that a constant pressure and temperature, the volume of a gas is directly proportional to the number of moles present.
Avogadro's Law
______ states that in the addition of polar reagents to alkenes, the positive portion of the reagents adds to the carbon atom in the double bond that already has the most hydrogen atoms.
Markovnikou's rule
_______ are atoms that have completely filled ns and np subshells, giving them great stability.
Noble Gases
_______ states that the partial pressure of a solvent over a solution is given by the vapor pressure of the pure solvent times the mole fraction of the solvent in the solution.
Raoult's Law
An investor has an option to purchase a tract of land that will be worth P20,000 in seven years. If the value of the land increases at 9% each year, how much should the investor be willing to pay now for this property?
P10,941 F = P(1+i)n
Suppose that you make 12 equal annual deposits of P2,000 each into a bank account paying 8% interest per year. The first deposit will be made one year from today. How much money can be withdrawn from this bank account immediately after the 12th deposit?
P37,954 F=A1+in-1i
What is the effective rate of interest if P1000 is invested at a nominal rate of 15% compounded quarterly?
15.86% ieff=(1+i)n-1
A man purchased a house for P425,000. In the first month that he owned the house, he spent P75,000 on repairs and remodeling. Immediately after the house was remodeled, he was offered P545,000 to sell the house. After some consideration, he decided to keep the house and have it rented for P4,500 per month starting two months after the purchase. He collected rent for 15 months and then sold the house for P600,000. if the interest rate was 1.5% per month, how much extra money did he make or lose by not selling the house immediately after it was remodeled?
P5,000 P545k-(4500(P/A))-(600k(P/F))
On the day his grandson was born, a man deposited to a trust company a sufficient amount of money so that the boy could receive five annual payments of P20,000 each for his college tuition fees, starting with his 18th birthday. Interest at the rate of 12$ per annum was to be paid on all amounts on deposit. There was also a provision that the grandson could elect to withdraw no annual payments and receive a single lump amount on his 25th birthday. The grandson chose this option. How much did the grandfather deposit?
P10,500 P = P20k(P/A,12%,5)(P/F,12%,17)
A man bought an equipment costing P30,000 payable in 12 quarterly payments, each installment payable at the beginning of each period. The rate of interest is 24% compounded quarterly. What is the amount of each payment
P3,700 P30k=A(1+P/A,8%,12-1)
A telecommunication company purchased an equipment for P53,000 and paid P1,500 for freight and delivery charges to the job site. The equipment has a normal life of 10 years with a trade-in value of P5,000 against the purchase of a new equipment at the end of the life. Determine the annual depreciation cost by the sinking fund method. Assume interest at 6.5% compounded annually.
P3.,668
A plant bought a machine for P200,000 and used it for 10 years, the life span of the equipment. What is the book value of the machine after 5 years of use? Assume a scrap value of P20,000. Use double declining balance method.
P65,536
It occurs when a cutting action is applied as you would see with scissors, tin snips, or punches.
Direct shear
It occurs when a member carries a load perpendicular to its long axis while being supported in a stable manner.
Bending stress
It is the internal resistance offered by a unit area of the material from which a member from which a member is made to an externally applied load.
Stress
A certain support stand design to carry downward loads. Compute the stress in the square shaft at the upper part of the stand for a load of 27,000 lb. The line of action of the applied of the applied load is centered on the axis on the shaft, and the load is applied through a thick plate that distributes the force to the entire cross section of the stand.
12,000psi
The proportional limit is the value of stress on the stress-strain diagram curve at which the curve first deviates from a straight line.
Proportional limit
It is the value of stress on the stress-strain curve at which the material has deformed plastically; that is, it will no longer return to its original size and shape after removing the load.
Elastic limit
It is the value of stress on the stress-strain curve at which there is a significant increase in strain with little or no increase in stress.
Yield point
It is the highest value of apparent stress on the stress-strain curve.
Tensile point
It is a measure of the stiffness of a material determined by the slope of the straight-line portion of the stress-strain curve.
Modulus of elasticity
A ductile material is one that can be stretched, formed, or drawn to a significant degree before fracture. A metal that exhibits a percent elongation greater than ____ % is considered to be ductile.
5
A brittle material is one that fails suddenly under load with little or no plastic deformation. A metal that exhibits a percent elongation ____ 5.0% is considered to be brittle.
Less than
The ratio of shearing stress to shearing strain is called
Modulus of rigidity
It is the ability of a material to absorbed applied energy without failure
Toughness
It is the indication of the resistance of a material to indentation by a penetrator.
Hardness
It is a measure of pulling and pushing force.
Axial force
It is the measure of the total resistance to sliding.
Shear force
It is the measure of the resistance to twisting.
Torque
A common bar suspended from certain support has axial load of 10kN. If the bar has a cross section of 20mm2, find the stress experience by the bar.
500MPa
Assume that a 25-mm diameter rivet joins the plates that are each 125 mm wide. The allowable stresses are 130 MPa for bearing in the plate material and 65 MPa for shearing of the rivet. Determine the minimum thickness of each plate.
40MPa ; ;
A cylinder pressure vessel is fabricated from plates which have a thickness of 20mm. The diameter of the pressure vessel is 450 mm and its length is 3.5m. Determine the maximum internal pressure which can be applied if the stress in the steel is limited to 150MPa.
16.67MPa
The wall thickness of a 3ft-diameter spherical tank is 4/17 in. Calculate the allowable internal pressure if the stress is limited to 9000 psi.
176.47psi
A steel bar 40mm in diameter and 3m long is surrounded by a shell of cast iron 6mm thick. Compute the load that will compress the combined bar a total of 0.95 mm in the length of 2m. For steel E=300GPa, and for cast iron, E=150GPa.
161kN
A steel rod 3.5m long is secured between two walls. If the load on the rod is zero at 30°C, compute the stress when the temperature drops to -30°C. The cross sectional area of the rod is 1200mm2, α =11.7um/(m°C), and E=200GPa.
140MPa
A steel shaft 3ft long that has a diameter of 5in is subjected to a torque of 14kip-ft. Determine the maximum shearing stress. G=12x106 psi.
0.47°
What is the minimum diameter of a solid steel shaft that will not twist through more than 4° in a 6m length when subjected to a torque of 13kN-m? What max shearing stress is developed? G=85 GPa
107.6mm
Determine the elongation in a helical steel spring composed of 20 turns of 20-mm diameter wire on a mean radius of 90 mm when the spring is supporting a load of 2.5kN. Use G=83 GPa.
175mm
It is the transfer of energy from the more energetic particles of substance to the adjacent less energetic ones as a result of interactions between the particles.
Conduction
It indicates that the rate of heat conduction in a direction is proportional to the temperature gradient in that direction.
Fourier's Law of Heat Conduction
Which of the following is considered the best conductor of heat?
Diamond
It is the mode of energy transfer between a solid surface and the adjacent liquid or gas that is in motion, and it involves the combined effect conduction and fluid motion.
Convection
It is the energy emitted by the matter in the form of electromagnetic waves as a result of the changes in the electronic configurations of the atom or molecules.
Radiation
It states that energy can neither be destroyed nor created; it can only change forms.
First law of thermodynamics
In second law of thermodynamic, which of the following state that no heat engine can have a thermal efficiency of 100% or as far as power plant to operate, the working fluid must exchange heat with the environment as well as the furnace.
Kelvin –Plank Statement
In second law of thermodynamic, which of the following state that no device can transfer heat from cooler body to a warmer one without leaving an effect on the surroundings.
Clausius Statement
It is defined as the amount of light output in lumens per W of electricity consumed.
Light efficacy
Carnot cycle is composed of how many reversible processes?
4
Which of the following processes are involved in Carnot cycle?
Two adiabatic; two isothermal
State that the thermal efficiencies of all reversible heat engines operating between the same two reservoirs are the same, and that no heat engine is more efficient than a reversible one operating between the same two reservoirs.
Carnot principle
A Carnot heat engine receives 500KJ of heat per cycle from a high-temperature source at 600 °C and rejects heat a low temperature sink at 40°C. Determine the thermal efficiency of this Carnot engine.
64.15%
A piston cylinder device contains a liquid-vapor mixture of water at 400K. During a constant pressure process, 700 KJ of heat is transferred to the water. As a result, part of the liquid in the cylinder vaporizes. Determine the entropy change of the water during this process.
1.75kJ/K
Which of the following equation of state has two constants?
Vander Waals Equation
How many constant are there in Strobridge Equation of State?
16
Which of the following equation of state has eight constant?
Benedict-Webb-Rubin Equation
Consider a person standing in a breezy room at 22°C. Determine the total rate of heat transfer from this person if the exposed surface area and the average outer surface temperature of the person are 1.2 m2 and 33°C, respectively, and the convection heat transfer coefficient is 6 W/m2.ε=0.95 and σ=5.67x10-8 W/m4-K4
143.2J/s
A piston cylinder device initially contains 0.8 m3 of air at 110kPa and 80°C. The air is now compressed to 0.2 m3 in such a way that the temperature inside the cylinder remains constant. Determine the work done during this process.
-122kJ
It is the energy possesses by the system as a result of its elevation with respect to the gravitational acceleration of the earth.
Potential
It states that if two bodies are in thermal equilibrium with a third body, they are also in thermal equilibrium with each other.
Zeroth law of thermodynamics
Determine the mass of the air in a room whose dimensions are (5x6x7) cm at 105 kPa and 27°C.
Heat is transferred to a heat engine from a furnace at a rate of 92MW. If the rate of waste heat rejection to a nearby river is 45MW, determine the net power output and the thermal efficiency for this heat engine.
51.09%
The food compartment of a refrigerator is maintained at 4°C by removing heat from it at a rate of 300 KJ/min. If the required power input to the refrigerator is 3KW, determine the coefficient of performance of the refrigerator.
1.67
A 50 kg iron block at 80°C is dropped into an insulated tank that contains 0.5 m3 of liquid water at 25°C. Determine the temperature when thermal equilibrium reached. The specific heat of iron is 0.45kJ/kg-°C and for water is 4.18kJ/kg-°C.
25.6°C
A rigid tank contains a hot fluid that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 850kJ. During the cooling process, the fluid loses 550kJ of heat, and the paddle wheel does 200kJ of work on the fluid. Determine the final energy of the fluid. Neglect the energy stored in the paddle wheel.
500kJ
Three moles of an ideal gas are compressed slowly and isothermally from a volume of 5 to 1.5 ft3, at a temperature of 320K. How much work is done?
-9.61kJ
A 4-in wall of fire brick, k=9 Btu/(ft2-hr-F/in), has one surface at 300F, the other at 90F. Find the heat conducted through the area of 2ft2 in 1 day.
22, 680Btu
If 80 g of iron shot at 100C is dropped into 200 g of water at 20C contained in an iron vessel of mass 50 g, find the resulting temperature.
24.6°C
When a 2lb of brass at 212°F is dropped into 5lb of water at 35°F, the resulting temperature is 41.2°F. Find the specific heat of brass in Btu/lb-°F.
0.091
How much heat is necessary to raise the temperature of 0.80 kg of ethyl alcohol from 15°C of its boiling point 78.3°C?
30 kcal
The weight-density of air at 32F and 29.92 in Hg pressure is 0.081 lb/ft3. What is its weight-density, in lb/ft3, at an altitude where the pressure is 13.73 in Hg and the temperature is -40F?
0.044
How many zeroes in the measurement 0.00020040 are significant?
Three
Which of the following describes a chemical change?
Tarnishing silver
A homogenous mixture can be separated by all of the following methods except
Filtration
Which of the following is not a pure substance?
Milk
A laboratory experiment was performed to determine the percent by mass of water in a hydrate. The accepted value is 36.0% water whose observed value has an error of 5.00%. Find the percent by mass of water.
37.8% water 36% * 1.05 =37.8%
Which of the following phase changes represent sublimation?
Solid gas
The amount of energy needed to change a given mass of ice to water at constant temperature is called the heat of
Fusion
Which of the following is a binary compound?
Hydrochloric acid
An example of a ternary compound is
Potassium chlorate
What is the charge of a hydrogen atom?
0
The impossibility of knowing both the precise location and velocity of subatomic particle at the same time is known as the
Uncertainty principle
An atom which has the greatest ability to attract electron is
Oxygen
From the reaction,
2NO+ O2 2NO2
How many molecules of NO2can be formed using 2 molecules of NO?
2
If the volume of the mole of gas molecules remains constant, lowering the temperature will make the pressure
Increase
Whenever you have equal volumes of gases at the same temperature and pressure, the volume must
Contain equal number of particles
What pressure must be applied to 225mL of gas at 1atm to reduce its volume to 100mL?
2.25atm P1V1=P2V2
How many moles of O2are present in 44.8L of O2 at STP?
2.0moles At STP, 1 mole will occupy 22.4L
The properties of solution include all of the following except that
Dissolved particles will settle out upon stirring
Suppose that energy Q is required to accelerate a car from rest to v, neglecting friction. How much added energy would be required to increase the speed from v to 2v?
3Q W=KE2 – KE1
Suppose you want to store 1.00 J of electric potential energy in a volume of 1.00 m3 in vacuum. What is the magnitude of the required electric field?
0.475 MV/m E=2uϵo; u = J/m3
Material ais a water and material b is a glass with index of refraction 1.52. If the incident ray makes an angle of 60o with the normal, find the direction of the reflected ray.
60˚ θr=θa
The wavelength of the red light from a helium-neon sensor is 633 nm in air but 474 nm in the aqueous humor inside our eyeballs. Calculate the speed of light in this substance.
2.25 x 108 m/s
A spaceship moving away from Earth with speed of 0.900c fires a robot space probe in the same direction as its motion, with speed of 0.700c relative to the spaceship. What is the probe's velocity relative to the Earth?
0.982c vr=va+vb1+vavbc2
In optics, this effect refers to the blurring of the image produced on a concave mirror due to the convergence of rays far from the mirror to other points on the principal axis. What do you call this effect?
spherical aberration
In fluid mechanics, this shows that the pressure of a fluid decreases as the speed of the fluid increases. In addition, the pressure of a fluid decreases as the elevation increases.
Bernoulli's equation
600 N34240 N125F1In electrodynamics, what term refers to the average speed of the charge carriers?
600 N
3
4
240 N
12
5
F1
drift speed
In electromagnetics and wave theory, what refers to waves, commonly generated by electronic devices, whose wavelengths ranges from approximately 0.3m to 10-4 m. Due to their short wavelengths these are often used in radar systems and for studying the atomic and molecular properties of matter.
Microwaves
These materials are hard and brittle, insulative to electricity and heat, and very resistant to high temperatures and harsh environments.
Ceramics
These materials have a large number of non-localized electrons, as an effect are very good conductors of electricity and heat. They are strong yet deformable, and extensively used in structural applications.
Metals
Materials composed of more than one material type and are designed to display a combination of the best characteristics of each component material.
Composites
A material whose atomic arrangement occurs as periodic, repeating structures over large distances.
Crystalline
An elemental solid having a different crystal structure, usually due to the prevailing temperature and pressure.
Allotrope
This metal is alloyed with steel to give it corrosion resistance properties, resulting in "stainless steel."
Chromium
This element is used in modern, super strong permanent magnets because of their high coercivities.
Neodymium
The deterioration of an engineered material due to interaction with diverse environments which lead to the degradation of its material properties.
Corrosion
The force of 600 N is the resultant of the forces F1 and 240 N acting as shown in the figure. Which of the following gives the value of F1.
698.9223 N, 56.310 with respect to the horizontal
Given the set of parallel forces shown, which of the following gives the resultant force.
100 KN 40 KN 60 KN 50 KN 60 KN
A B
2m 2m 2m 6m 3m
90 KN down, 3.33m fr A
The coefficient of friction between the rope and fixed post is 0.30. The rope is wrapped only once around the post. Which of the following gives the minimum tension in the rope at pt A
A
300 N B
138.6873 N 300/T = e0.4Π
The resultant of the concurrent forces has a magnitude of 1200 N and acts through the origin and points x = 3m, y = 4m, z = 5m. Which of the following gives the x component of the resultant force
509.1146 N
From the speed of 100 kph, a car decelerates at the rate of 15 m/min/sec along a straight road. Which of the following gives the distance travelled at the end of 40 sec.
911.112 m
The velocity of a particle moving along the x axis is defined by v = x4 + 2x3 – 3x2where v is in m/s and x is in m. Which of the following gives the velocity when x = 2m.
20 m/s
The block shown reaches a velocity of 10 m/s in 25 m starting from rest. Which of the following gives the coefficient of kinetic friction between the block and the ground.
600 N
Vo= 0 V1 = 10 m/s
280N
25 m
0.2626
The normal acceleration of a particle on the rim of a pulley 10 ft in diameter is constant at 1200 fps2. Which of the following gives the speed of the pulley in rpm.
147.9371 an = v2/r,v = rω
A 350 N block is resting on a plane inclined at 300 with the horizontal is subjected to a constant force of 400 N acting parallel to the inclined plane. After the block has moved 3 m from rest, the 400 N force was removed. Coefficient of friction is 0.2. Which of the following gives the distance that the block will move further along the inclined plane until it stop.
350 N
400 N
30˚
2.714m
The force system consist of a clockwise couple of 600 N-m plus a 300 N force directed to the right through the origin of x & y axes at θx = 300.
O300
O
300
300N
600 N-m
If the system is replaced by an equivalent single force, which of the following is its x and y intercept.
4 m left and 2.3094 below the origin
The position x of an experimental rocket moving along a long rail is measured to be x(t) = (4m/s)t + (7m/s2)t2 + (5m/s3)t3 – (0.35m/s4)t4 over the first 10s of its motion, where t is in seconds and x is in meters. Find the velocity of the rocket for the first 10 seconds.
244m/s v = dx/dt
Early in the nineteenth century, James Watt invented the steam engine. In order to convince people, who relied heavily on horses for mechanical work, he demonstrated how useful his steam engine was by utilizing a horse that lifted water from a well over a certain period of time and called the corresponding power expended "one horsepower". Assume that water has a mass density of 1.0 x 103 kg/m3, that the well was 20m deep, and that the horse worked for 8 hours. How many liters of water did the horse raise from the well? Use the following constants: 1 hp = 746 Watts, g = 9.8 m/s2.
1.1 x 105 L; 1 m3 = 103 L
As provided in ACT 3846, the construction of a radio station shall begin only when
The NTC has already issued a Permit to construct.
As provided in RA7925, a VAS provider needs to secure a franchise if
it puts up its own network.
According to the code of ethics, if you are employed in a company and you wish to engage in a business which may compete with your company, the most ethical thing to do is to
inform your employer about it
The property of a substance which remains constant if no heat enters or leaves the system, while it does work or alters its volume, but which increases or diminishes should a small amount of heat enter or leave.
Entropy
The quantity of heat required to change the temperature of unit mass through one degree.
Specific Heat
"If the temperature of a given quantity of gas is held constant, the volume of the gas varies inversely with the absolute pressure during a change of state"
Boyle's Law
An internally reversible process of a substance during which the pressure remains constant.
Isobaric
The energy stored in a substance by virtue of the activity and configuration of its molecules and of the vibration of the atoms within the molecules.
Internal Energy
"When two bodies, isolated from other environment, are in thermal equilibrium with a third body, the two are in thermal equilibrium with each other" is a statement of…….
Zeroth Law
"Not all energy received as heat by a heat-engine cycle can be converted into mechanical work, some are also rejected" is a statement of……
2nd Law of Thermodynamics
The combined mass of car and passengers travelling at 72 km/hr is 1500kg. Find the kinetic energy of this combined mass.
300kJ KE = ½mv2
A mass of 5kg is 100m above a given datum where local g=9.75 m/sec2. Find the gravitational force in newton's and the potential energy of the mass w/ respect to the datum.
48.75 N, 4875 J
A pressure gage register 50 psig in a region where the barometer is 14.25 psia. Find the absolute pressure in Pa.
443 kPa
During an isentropic process of 1.36 kg/sec of air, the temperature increases from 4.44° C to 115.6°C. ifCp=1.0062kNmfor a non-flow process, what is H? kg K
152.2 kJ/s H = mCp T
This Law States that " The quantity of the substance entering the system is equal to the substance leaving the system"
Law of Conservation of Mass
"if the pressure of a given quantity of gas is held constant, the volume of the gas varies directly with the absolute temperature"
Charles' Law
"The Acceleration of a particular body is directly proportional to the resultant force acting on it and inversely proportional to its mass" is a statement of
Newton's 2nd Law of Motion
"Energy is neither created nor destroyed, but is converted from one form to another"
1st Law of Thermodynamics