The writing is on Abacus, an calculating device used in eastern Asia.
The writing is on Abacus, an calculating device used in eastern Asia.
Fade MarginFull description
*PB 0 is mean there is no increment on CRS RE it’s mean non power boosting, but PDSCH power increase to 5/4. *By using PB 1, the RS Power increase on CRS RE two units it’s mean about power boostin...
Metal Casting Feeders
Fade Margin
TCP/IP Throughput CalculationFull description
Descripción: Metal Casting Feeders
*PB 0 is mean there is no increment on CRS RE it’s mean non power boosting, but PDSCH power increase to 5/4. *By using PB 1, the RS Power increase on CRS RE two units it’s mean about power …Deskripsi lengkap
CT SizingFull description
Descrição: CT Sizing
Full description
Calculate square of nine angles in excel
manalFull description
Deskripsi lengkap
Full description
Chemsitry
fashion
How to Calculate Anchorage and Lap Lengths to Eurocode 2Full description
IEC 781 (1989-01)Guidance to Calculate Short Ckt CurrentFull description
Basura 1
This manual aims at walking the reader through the design of a water supply network in a development context by explaining in a simple manner how to build and analyze a computer model of a w…Descrição completa
How to calculate Locked Rotor Current (I L) From Nameplate Data The lock rotor amps is the current draw of the motor when the motor is switched on and before the rotor starts to turn. This is the stator current but it is called l ock rotor current for 2 reasons. (1) The measured current is at a t ime (0 sec) ie when the rotor i s at standstill ,thus the rotor is considered "LOCKED" and thus the term LOCK RO TOR AMPS. (2) You can mechanically strap down the rotor (LOCK ROTOR),press the start button a nd measure the stator current. This lock rotor amps is the highest current draw of the motor because when the rotor is locked impedance is the lowest. Item 2 above You can use a clip on to measure the Lock rotor amps. Another method for measuring lock rotor amps is by using a storage oscilloscope and a passive resistor. Regards
3-Phase:
Single phase:
See: KVA/HP Chart EXAMPLE:
Motor nameplate indicates 10 HP, 3 Phase, 460 Volts, Code F. 577 x 10 x (5.6 or 6.29) IL = 460 IL = 70.25 or 78.9 Amperes (possible range)
Effect Of Line Voltage On Locked Rotor Current (I L) (Approx.) ELINE IL @ ELINE = IL @ EN/P x EN/P
How to Calculate Motor Inrush Current A motor, with the power turned off, presents little resistance to electricity because the motor windings act almost like a short until they become energized. When power is turned on, the current flow may be many times what the current flow is when the motor is operating at rated speed under a load. This inrush of current lasts only a fraction of a second. No calculation for the exact inrush current is possible, but a range may be determined if the manufacturer's documentation does not specify it. Instructions 1. Read the motor nameplate on the motor and find the voltage listed on it. The National Electric Code mandates all motors have a nameplate that provides information specific to the electrical operating characteristics of the motor. 2. Look for the "Locked Rotor Letter Code" or "Locked Rotor Code" on the motor nameplate. This code will be a letter from "A" to "V" but will not include "I," "O" or "Q." These letters are omitted to avoid confusion. 3. Consult the NEMA Locked Rotor Code Table and find the letter code on it. Follow the letter code row to the right and find the range given. The range is given in thousands of Volt-Amps, or kilowatts. 4. Multiply each number in the range by 1,000. Divide each result by the motor voltage found on the nameplate. The resulting range is the inrush current range. For example: A 3.5-horsepower, three-phase motor nameplate lists the motor voltage as 230 volts and the locked rotor code is "K." The range given on the table is 8.0 to 8.99 KVA. Multiplying by 1,000, the range becomes 8,000 to 8,990 VA. Dividing by the motor voltage of 230 volts gives the inrush current range as 34.8 amps to 39.1 amps.
Tips & Warnings
The inrush current is only momentary and if the circuit breaker is sized properly, it will not trip in the fraction of second the current spikes. As the motor windings become energized, they present resistance to the flow of current and the current begins to drop. As the motor comes up to full
speed, the current level will be at the level specified on the motor nameplate as the full-load current.
The voltage is important to determining inrush current. If the motor nameplate lists multiple voltages, the voltage being used must be determined. An easy place to measure this is at the motor disconnect. The type of voltage determines how the measurement is made. Measure three-phase current between two hot terminals and double it. Split phase current is measured between two hot terminals. Single phase current is measured from the hot terminal to ground
Read more: How to Calculate Motor Inrush Current | eHow.com http://www.ehow.com/how_7791777_calculate-motorinrush-current.html#ixzz2NayKtBP6
