SCROLLSAW PATTERNS: Following are the full-size scrollsaw patterns for creating beautiful projects from our CD Scrollsaw Pattern Book. Each pattern is shaded to make it easier to see where to cut and where not to cut. To navigate from page to page, simply use the vertical scrollbar on the right hand side of the screen, or the “Go To” buttons located at the top and bottom of the screen. To print, simply click on the “Printer Icon” at the top of the screen, or choose “Print” from the “File” pull-down menu. Be sure to specify which page numbers you want to print, and the number of copies. You can determine the page number from the “Page #” box 4 of 107 at the bottom of the screen. When finished, click the “First Page” button to go back to the beginning to choose another section to view. GREAT AMERICAN PATTERNS TM
Simply click on the button of your choice. INTRO
PHOTOS
HOW-TO
MORE CD’S AVAILABLE
PATTERNS
BACK TO START
Pattern overlap line
Stock: 1/4” Assemble with #18 x 5/8” finish nails and glue. Top pattern piece.
Crest
Victorian Display Stand
Victorian Display Stand
Pattern overlap line
Stock: 1/4” Bottom left pattern piece.
Assemble with #18 x 5/8” finish nails and glue.
Pattern overlap line
Crest
Pattern overlap line
Pattern overlap line
Crest
Stock: 1/4” Bottom right pattern piece.
Stock: 1/4” Top pattern piece.
Back
Pattern overlap line
Victorian Display Stand
Stock: 1/4” Bottom pattern piece.
Back
Pattern overlap line Victorian Display Stand
Victorian Display Stand
Side Stock: 1/4", cut 2 Attach to Back and Bottom with glue and #18 x 5/8” finishing nails.
Victorian Display Stand
Cut ends at 45°
Roof
Cut ends at 45°
Roof, end view
Back
Stock: 1/4” Cut 2. Glue and nail to Back
Victorian Display Stand
Bottom Stock: 1/4”
Roundover 1/4” R
Victorian Display Stand
Roundover 1/4” R.
Base Stock: 1/4” Left pattern piece.
Pattern overlap line
Bottom
Back
Victorian Display Stand
Base Stock: 1/4” Right pattern piece.
Pattern overlap line
Bottom
Back
Nativity Scene
Left Frame Stock: 1/4" - 3/8"
Center 3/4" 1 1/2" Hinges where indicated
Nativity Scene
Center Frame Stock: 1/4” - 3/8”
Nativity Scene
Right Frame Stock: 1/4” - 3/8”
Center 3/4" 1 1/2" hinges where indicated
Pattern overlap line
Wedding Anniversary Heart
Frame Stock: 1/4” - 3/8” Left pattern piece.
Pattern overlap line
Wedding Anniversary Heart
Frame Stock: 1/4” - 3/8” Right pattern piece.
Victorian Cross with Shelf
Bracket Stock 1/4”
Stock: 1/4” Bottom pattern piece. Attach Shelf and Bracket with glue.
Back
Adjust slots, if necessary, for the thickness of material used.
Pattern overlap line
Victorian Cross with Shelf
Stock: 1/4” Top pattern piece.
Back
Pattern overlap line
Victorian Cross with Shelf
Stock 1/4”
Shelf
Victorian Cross with Shelf
Wildlife Clock
12 3
9 6
Option: drill for hanging clock.
Frame Stock: 3/8”
Bore a 2 3/8” hole for a 2 3/4” clock insert
Option: cut on dashed line for hanging clock.
Base Stock: 3/8”
Adjust slot, if necessary, for thickness of material you are using. Secure with glue or silicone.
Victorian Sconce
Back Stock: 3/4” Top pattern piece.
Side View 1/4" R Typ. 3 1/2° 1/4"
Veneer on plywood backer.
Pattern overlay line
Victorian Sconce
Pattern overlap line
Rabbet back side for fretted insert
Back Stock: 3/4” Bottom pattern piece.
Roundover front edges 1/4” R.
.
Drill a 1/16” hole to start bevel cut. Cut clockwise with table tilting down to the right at 3 1/2° or cut counterclockwise with table tilting down to the left at 3 1/2°.
Roundover front edges 1/4” R. Drill and countersink back side for #9 x 1 1/2” F.H. screws.
Victorian Sconce
In
Sto ser ck: t 1/4 "
Victorian Sconce
Roundover front edge 1/4” R.
Optional: Drill hole or add candle cups
Shelf Stock: 3/4"
Anniversary Plate
Note: Use repositionable spray adhesive to attach the pattern to the work pieces. Cut the interior Plate Design and the Rim Design. Use glue or silicone to attach the Rim to the Interior Design. Finish as desired.
Interior Plate Design Stock: 1/4” - 3/8”
Anniversary Plate
Rim Design
Dashed line indicates position of Interior Plate Design on back of Rim
Pattern overlap line
Stock: 1/8” - 1/4” Left pattern piece.
Anniversary Plate
Rim Design Stock: 1/8” - 1/4” Right pattern piece.
Numbers Pattern overlap line
Stock: 1/16” - 1/4” Secure in place with glue or silicone.
Victorian Clock
Assembly Instructions Assemble by first attaching the Aprons to the End Aprons. Then attach the Base to this assembly and the Bottom to the Base. Next attach the Front and Back to the Sides. Then attach the Roof, Side inserts, and Crest. Next position this assembly over the Bottom and secure in place with glue or silicone. Attach the Rail, and finish as desired.
C
J A
B 11
12
1 2
10
3
9 4
8 6
5
F
L D G
I H
Description Front Back Crest Rail Side Side Insert Base Apron End Apron Roof Overlay Bottom
Item Qty A B C D E F G H I J K L
1 1 1 1 2 2 1 2 2 2 1 1
Stock: 1/4”
Victorian Clock Rail (D)
7
Stock: 1/4”, cut 2
F
K
End Apron (I)
E
Dashed line indicates placement of Overlay
Attach to Sides with glue and #18 x 5/8” finishing nails.
Bore a 2 3/8” hole for 2 3/4” clock insert in Front only.
Cut design in Front only.
Stock: 1/4”, cut 1 each Top pattern piece.
Stock: 1/4”, cut 1 each Bottom pattern piece.
Front (A) & Back (B)
Front (A) & Back (B)
Pattern overlap line
Pattern overlap line
Victorian Clock
Use glue and finishing nails to attach to Front of Roof.
Stock: 1/4”
Crest (C)
Victorian Clock
Victorian Clock
Top
Side (E) Stock: 1/4”, cut 2 Attach to End Aprons with glue and finishing nails
Side Insert (F) Stock: 1/4”, cut 2
Apron (H)
Stock: 1/4”, cut 2
Top
Apron
Stock: 1/4”
Bottom (L)
Stock: 3/8” - 1/2”
Base (G)
Small dashed line indicates placement of Bottom (L)
Slot for Rail (D)
Use glue and #18 x 5/8” finishing nails to attach Base (G) to Aprons.
Victorian Clock
End Apron
End Apron
Victorian Clock
45° Cut at 45° Front
Roof (J)
Side view of Roof
Stock: 1/4”, cut 2
Cut at 45° 45°
Overlay (K) Stock: 1/4”
Bore a 2 3/8” hole for 2 3/4” clock insert.
Small Shelves
Back Stock: 3/8"
Back Stock: 3/8"
Small Shelves
Shelf Stock: 3/8"
Attach to Back with glue and #18 x 3/4” finishing nails or countersink for #4 x 5/8” F.H. screws.
Pattern overlap line
Glue bars into place
Cut two vertical stiles
Stock: 3/4”, cut 2 Top pattern piece.
Side
Earring Holder
Pattern overlap line
Roundover top edges 1/4” R.
Roundover top edges 1/4” R.
Drill for shaker pegs to hole necklaces
Top Stock: 3/4’ Left pattern piece.
Drill and countersink back side to attach Sides with #9 x 1 1/2” F.H. screws.
.
Stock: 3/4” Cut 2 Bottom pattern piece.
Side
Continuous groove, 1/4” x 5/16” deep
Pattern overlap line
1/4” R roundover, forward edges only.
Earring Holder
3 1/2° 1/4" R
Pattern ovelap line
Side view of raised heart section
Top Stock: 3/4’ Right pattern piece.
. Drill a 1/16” hole to start bevel cut. Cut clockwise with table tilting down to the right at 3 1/2° or cut counterclockwise with table tilting down to the left at 3 1/2°.
Stock: 3/4” Right pattern piece.
Base
Drill and countersink bottom side to attach stiles with #9 x 1 1/2” F.H. screws.
Stock: 3/4” Left pattern piece.
Base
Roundover top edge 1/4” R
Earring Holder Pattern overlap line
Pattern overlap line
Earring Holder
Pattern overlap line
Bar
Stock: 1/4” Cut 5 complete Bars Right pattern piece.
Bar
Stock: 1/4” Cut 5 complete Bars Left pattern piece.
Pattern overlap line
Collapsible Basket
Drill 1/8” pivot hole before sawing basket free. After routing 1/4” R countersink screws.
Drill a 1/16” hole to start bevel spiral cut. Saw at 3 1/2° with table tilting down to the left and using a #9 blade.
. Frame Stock: 3/4" Left pattern piece.
Pattern overlap line
Roundover 1/4” R.
Drill & countersink 1/8”. Attach pivot foot with #6 x 3/4” F.H. screw.
Pattern overlap line
Collapsible Basket
Roundover 1/4” R outside edges
. Frame Stock: 3/4" Right pattern piece.
Drill 1/8” pivot hole before sawing basket free. After routing 1/4”R countersink for #6 x 1 1/4” F.H. screws.
Drill a 1/16” hole to start bevel spiral cut. Saw at 3 1/2° with table tilting down to the left using a #9 blade.
Pattern overlap line
Collapsible Basket
. Frame Stock: 3/4" Left pattern piece.
Roundover 1/4” R.
1/8” drill & countersink. Attach pivot foot with #6 x 3/4” F.H. screw.
Collapsible Basket
Pattern overlap line
Roundover 1/4” R outside edges
. Frame Stock: 3/4" Right pattern piece.
Drill 1/8” pivot hole before sawing basket free. After routing 1/4” R countersink for #6 x 1 1/4” F.H. screws.
Drill a 1/16” hole to start bevel spiral cut. Saw at 3 1/2° with table tilting down to the left and using a #9 Olson blade.
Pattern overlap line
Collapsible Basket
. Frame Stock: 3/4" Left pattern piece.
Roundover 1/4” R
1/8” drill & countersink. Attach pivot foot with #6 x 3/4” F.H. screw.
Collapsible Basket
.
Pattern overlap line
Roundover 1/4” R outside edges
Frame Stock: 3/4" Right pattern piece.
Friendship Plate
Rim Design
Pattern overlap line
Stock: 1/8” - 1/4” Top left pattern piece.
Enlarging or reducing this pattern will allow you the flexibility of fitting it to the location where you choose to display it. Also, using contrasting woods or stains will produce the most stricking effect.
Pattern overlap line
Friendship Plate
Rim Design
Dashed line indicates position of Interior Design on back of Rim. Use glue and/or finishing nails to attach Interior Design to the back of the Rim.
Stock: 1/8” - 1/4” Bottom pattern piece.
Rim Design
Pattern overlap line
Pattern overlap line
Stock: 1/8” - 1/4” Top right pattern piece.
Pattern overlap line
Pattern overlap line
Friendship Plate
Interior Design
Stock: 1/4” - 3/8” Right pattern piece.
Interior Design
Stock: 1/4” - 3/8” Left pattern piece.
Pattern overlap line
Corner Shelf Apply a small amount of glue to each side of tabs before assembly.
Shelf Stock: 1/4”, cut 2
Assemble by first inserting the Shelf tabs into one Side. Then attach the remaining Side.
Side (A) & (B) Stock: 1/4”, cut 1 each as indicated. Top pattern piece.
Pattern overlap line
Cut on this line for Side (A) Cut on this line for Side (B)
Adjust slots, if necessary for thickness of material used. Pattern overlap line
Attach Sides with glue and or #18 x 5/8” finishing nails.
Corner Shelf
Side (A) & (B) Stock: 1/4”, cut 1 each as indicated Bottom pattern piece.
Victorian Book Rack
B
r Sto ack ck: et 1/4 ”
First attach the Top and Bottom and Bracket to One Side. Attach the remaining Side.
Stock: 1/4”, cut 2
Side
Attach Top, Bottom and Bracket with glue and #18 x 5/8” finishing nails.
Pattern overlap line
Victorian Book Rack
Stock: 1/4”, cut 2 Bottom pattern piece.
Side
Pattern overlap line
Victorian Book Rack
Stock: 1/4”, cut 1 each
Top & Bottom
Victorian Book Rack
Carriage Planter / Candy Holder
Carriage Planter / Candy Holder C F
G D
E
A
B E
I
H
Assemble by first inserting the tabs of pieces B, C, D, E and F into one Side. Secure with glue. Then attach the remaining Side. Next, slide pieces G into place on the front and back of carriage. Finally, attach the Wheels with glue. Note: This carriage can be used for a variety of purposes - fill with candy, silk flowers, hair ribbons, pencils, guest soaps, potpourri. The possibilities are endless - just use your imagination. Fill with special treats for a unique gift basket!
Description Item Qty Side A 2 Floor B 1 Seat C 1 Foot Rest D 1 Axle E 2 Spacer F 1 Front & Back G 1 ea Front Wheel H 2 Back Wheel I 2 Floor (B) Stock: 1/8”
Seat (C) Stock: 1/8”
Foot Rest (D) Stock: 1/8”
Spacer (F) Stock: 1/8”
Axle (E) Stock: 1/8”, cut 2
D
E
C
D
G
Stock: 1/8”, cut 2
Side (A)
B
Note: Adjust slots, if necessary, for the thickness of material used.
G
E
F
Carriage Planter / Candy Holder
Carriage Planter / Candy Holder
Front Wheel (H) Stock: 1/8”, cut 2
Front & Back (G) Stock: 1/8”, cut 1 each
Back Wheel (I) Stock: 1/8”, cut 2
Music Box
Top
1 2 Back
3 Back
3/4
Foot Instructions 1. Attach pattern with repositionable spray. 1” 2. Cut out back shape 3. Cut out the top shape 4. Attach Foot with glue and finishing nails or silicone
Side view of Music Box Top
Metal Turntable
Music Box Key For music box tune selection and pricing, call THE BERRY BASKET at 1-800-206-9009.
Assembly Instructions Assemble by first attaching the Top to the Frame with glue and finishing nails or silicone. Next attach the music box movement to the topside of the Bottom with screws or silicone. Before the silicone sets, be sure to position the Frame over the Bottom to make sure the music box movement is aligned correctly. Then secure the Bottom to the Frame. Next, attach the Feet where indicated, securing with wood glue or silicone. Finish as desired. NOTE: It is important that the music box movement bottom is in contact with the wood (topside of the Bottom) in order to have the best tone. If using silicone, be careful to not use too much as it may squeeze out from between the 2 pieces and get into the movement itself.
Front
Foot
Top view.
Stock: 3/4”, cut 2 Fold on dashed line Rear view
Frame Stock: 1 1/2” Circle indicates position of key.
Cut out for music box
Note: Top is not intended to be used with a turntable. Secure the Top to the Frame with glue or silicone.
Music Box
Top Stock: 1/4”
Music Box
Bottom Stock: 1/4”
Dashed line indicates position of Frame
Drill 3/8” in Bottom for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Large Mantle Clock
12 3
9 6
Bore a 3” hole for a 3 1/2” O.D. clock insert.
Roundover front edges 1/4” R.
3/4" 1/4" 1/4"
Frame Stock: 3/4" Left pattern piece. Rabbet backside for fretted insert.
Pattern overlap line
1/4" R
1/4" R
Pattern overlap line
Large Mantle Clock
Frame Stock: 3/4” Right pattern piece.
Stock: 1/4”
Insert
Large Mantle Clock
Stock: 1/4"
Insert
Large Mantle Clock
Stock: 1/4"
Insert
Large Mantle Clock
Large Mantle Clock
Pattern overlap line
Base Stock: 3/4” Right pattern piece.
Roundover top edge 1/4” R.
Base Stock: 3/4” Left pattern piece.
Drill and countersink bottom side for #9 x 1 1/2” F.H. screws.
Pattern overlap line
Stock: 1/4"
Frame
9
Bore 1 3/8” hole for clock insert.
12 3
Victorian Desk Set
6
1/4” groove, 3/8” deep
Stock: 3/4"
Base
Drill for pen and funnel set
Stock: 1/4”, cut 2
Card Bracket
Roundover top edge 1/4” R before grooving.
Victorian Desk Set
Card Bracket
Card Bracket
Drill for pen and funnel set
Roundover top edge 1/4” R.
Stock: 1/2” - 3/4”
Base
9
Drill and countersink bottomside for #7 x 1 1/2” F.H. screws.
Executive Desk Set
12 3
6
Executive Desk Set
Frame Stock: 1/2” - 3/4”
Bore 3” hole for 3 1/2” O.D. clock insert.
Wildlife Lamp
Assembly Instructions Assemble by first inserting the tabs in the Bottom and Top into one Side containing the 2 slots. Secure with glue. Attach the remaining Side containing the 2 slots. Then slide the remaining Sides into position. Assemble the lamp as per instructions. Finish as desired. Option: use contrasting material behind design if desired. Note: order lamp kit #A243 or #A251 to complete.
Bottom and Top Stock: 1/4”, cut 1 each
Drill 3/8" to insert lamp rod.
Top
Top
Cut two sides with top slots
Cut two sides with top slots
Wildlife Lamp
Stock: 1/4”, cut 4 Bottom
Bottom Cut slots on two Sides only
Adjust slots, if necessary, for thickness of material you are using.
Cut two sides with bottom slots
Cut two sides with bottom slots
Side
Ornamental Frame
Overlay Stock: 1/16” - 1/4”
Pattern overlap line
Stock: 1/4” - 3/8” Top pattern piece.
Frame
Ornamental Frame
Stock: 1/4” - 3/8” Bottom pattern piece.
Frame
Pattern overlap line
Ornamental Frame
Holiday Plate
Rim Design
Pattern overlap line
Stock: 1/4” Left pattern piece.
Holiday Plate
Rim Design
Star Stock: 1/16” - 1/8”
Pattern overlap line
Stock: 1/4” Right pattern piece.
Stock: 1/8” - 1/4”
#2 - Interior Plate Design
Holiday Plate
Wildlife Wall Clock
Bore 1 3/8” hole for clock insert or picture frame.
Frame Stock: 1/4” - 3/8”
Rockin’ Reindeer
Drill for 1/4” dowel
Side Stock: 3/4”, cut 2 Left pattern piece.
Pattern overlap line
Dashed line indicates placement of Body.
Rockin’ Reindeer Drill for 1/4” dowel
Antler
Pattern overlap line
stock: 3/4”, cut 2
Side Stock: 3/4”, cut 2 Right pattern piece.
Drill for 1/4” dowel Dashed line indicates placement of Body.
Drill for 1/4” dowel
Drill for 1/4” dowel
Stock: 1 1/2”
Body
Dashed line indicates placement of Antlers
Drill for 1/4” dowel
Rockin’ Reindeer
Sleigh
Seat Stock: 1/2”
Sleigh
Side Stock: 1/2”, cut 2 Left pattern piece.
Drill and countersink for #7 x 1 1/4” F.H. screws.
Pattern overlap line
Roundover outside edges 1/4” R.
Sleigh
Pattern overlap line
Roundover outside edges 1/4” R.
Side Stock: 1/2”, cut 2 Right pattern piece.
Sleigh
Back Stock: 1/2”
Drill and countersink backside to attach Seat with #6 x 1 1/4” F.H. screws.
Napkin / Letter Holder
Frame Stock: 3/4" Cut 2
3/4"
Roundover, 1/4” R.
1/4"
1/4"
Rabbet backside for fretted insert
Insert Stock: 1/4” Cut 2
Napkin / Letter Holder
Insert Stock: 1/4” Cut 2
Insert Stock: 1/4” Cut 2
Roundover top edge 1/4” R.
Drill and countersink bottomside to attach Frames with #6 x 1” F.H. screws.
Stock: 3/4”
Base
Napkin / Letter Holder
Birdhouse
Roof
Back
Front
Stock: 1/4” Cut 2
Note: saw ends at 60°
Attach to front edge of Roof with glue and #18 x 5/8” wire brads.
Stock: 1/4” Cut 2
Front & Back Overlay
Birdhouse
Attach to front edge of Roof with glue and #18 x 5/8” wire brads.
Stock: 1/4” Cut 2
Front & Back Overlay
Birdhouse
Birdhouse
Side Stock: 1/4” Cut 2
60°
Cut edge at 60°
Bottom Stock: 1/4”
Stock: 1/4”, cut 1 each Assemble with #6 x 3/4” brass screws or #18 x 5/8” finishing nails and glue.
Front /Back
1/4” diameter x 4” dowel
Drill 1 1/4” diameter hole in Front only.
Birdhouse
