1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
Placement Papers
Aptitude Prep
Interview Prep
General Knowledge
Online Test
Buy Now
Home > GATE > GATE Chemical-Engineering 2013 solved questions
M.Tech from Manipal Univ. manipal.edu/Admissions_Open_2014 Ranked 5th Among Top Engg. Colleges with Excellent Coaching. Enroll Now
GATE Placement-Paper : 44019 Like
2
Views : 714 Rating : 1 students found similar paper in exam
Share
Paper Type : Chemical-Engineering
Most viewed papers of GATE
Posted By : sukrutha
GATE Chemical-Engineering 2013 solved questions
Updated Date : Dec 4, 2013
Category : Chemical-Engineering GATE
GATE Chemical-Engineering placement paper Question and answers GATE recruitment process and aptitude test experiences
714 views ,
GATE Exam - Chemical Engineering solved questions for learn and practice GATE previous years solved question papers of CS, mechanical, Civil, Chemical. Electrical, electronics etc GATE 2013 Graduate Aptitude Test in Engineering.Chemical engineering solved question papers 1 An open tank contains two immiscible liquids of densities (800 kg/m3 and 1000 kg/m3) as shown in the figure. If g = 10 m/s2, under static conditions, the gauge pressure at the bottom of the tank in Pa is __________
View Paper
GATE Mechanical Engineering Category : Mechanical-Engineering GATE 9878 views , View Paper
GATE Computer-Science-Engineering Category : Computer-Science-Engineering-CS GATE 12697 views , View Paper
GATE CS Cumputer Science Previous years solved question papers Category : Computer-Science-Engineering-CS GATE 7810 views , View Paper
GATE Information-Technology Category : Information-Technology-IT GATE 841 views ,
2 An incompressible Newtonian fluid, filed in an annular gap between two concentric cylinders of radii R1 and R2 as shown in the figure, is flowing under steady state conditions. The outer cylinder is rotating with an angular velocity of Ω while the inner cylinder is stationary. Given that (R2 – R1) << R1, the profile of the θ-component of the velocity Vθ can be approximated by,
View Paper View All
Most Viewed Practice Tests Level1 Quantitative practice Test 6 paid 30 questions 30 min 7156 students taken
TCS Placement Paper free 35 questions 80 min 12742 students taken
Wipro Placement Paper free 50 questions 60 min 3936 students taken 3 In the Tyler standard screen scale series, when the mesh number increases from 3 mesh to 10 mesh, then (A) the clear opening decreases,-Answer (B) the clear opening increases, (C) the clear opening is unchanged (D) the wire diameter increases.
Cognizant (CTS) Placement Paper free 55 questions 60 min 4087 students taken
Employability Assessment Test free 25 questions 25 min 4043 students taken
4 Velocity ;of an object fired directly in upward direction is given by V = 80 – 32 t, where t (time) is in seconds. When will the velocity be between 32 m/sec and 64 m/sec? (A) (1, 3/2) (B) (1/2, 1) (C) (1/2, 3/2) -Answer (D) (1, 3) 5
Following table gives data on tourists from different countries visiting India in the year
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
1/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
2011.
Country USA England Germany Italy Japan Australia
Number of Tourists 2000 3500 1200 1100 2400 2300
France
1000
Which two countries contributed to the one third of the total number of tourists who visited India in 2011 ? (A) USA and Japan (B) USA and Australia (C) England and France-Answer (D) Japan and Australia 6 In a factory, two machines M1 and M2 manufacture 60% and 40% of the auto components respectively. Out of the total production, 2% of M1 and 3% of M2 are found to be defective. If a randomly drawn auto component from the combined lot is found defective, what is the probability that it was manufactured by M2? (A) 0.35 (B) 0.45 (C) 0.5 -Answer (D) 0.4
Get help on Admission from HTCampus Student Name Email
7 If |- 2X + 9 | = 3 then the possible value of |- X | X2 would be (A) 30 (B) -30-Answer (C) -42 (D) 42
Mobile Number Select C urrent Location Select Highest Qualification Select C ourse C ategory Select Sub C ategory
8 All professors are researchers Some scientists are professors
Select C ourse Type
Which of the given conclusions is logically valid and is inferred from the above arguments?
Select Year Of Entrance Select Will Student Need Loan
(A) All scientists are researchers (B) All professors are scientists (C) Some researchers are scientists-Answer D) No conclusion follows.
I agree to T&C and allow htcampus to contact me
Model questions paper of GATE sample placement papers questions with answers and detailed explanations. GATE Chemical engineering Classified Multiple choice Questions Selected from Examination Papers of various Engineering Colleges Examinations
and
Competitive
1. Nitrogen compounds are not used in the manufacture of (a) fertilisers (b) gun powder (c) tip of match sticks (Ans) (d) explosive 2. The pH value is the measure of hydrogen ion concentration in a solution. The term pH stands for the ........ in the solution. (a) power of hydrogen ion concentration (Ans) (b) percentage of hydrogen ions (c) presence of hydrogen ions (d) none of these 3. (a) (b) (c) (d)
Electrode potential is not concerned with the measurement of pH value temperature (Ans) viscosity density
4. (a) (b) (c) (d)
A material lacking in toughness is usually termed as plastic malleable brittle ductile (Ans) ductile
5. (a) (b) (c) (d)
Otto cycle used in spark ignition petrol engines is also known as the constant....... cycle. volume (Ans) pressure heat none of these
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
2/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
6. Pick out the wrong statement. (a) In a thin spherical shell under internal pressure, hoop stress is equal to the half of axial stress. (Ans) (b) Thermoplastic material does not follow Hooke's law of elasticity. (c) Components under longitudinal compression is called 'struts' and the load under which strut fails is called crippling or buckling load. (d) At low temperatures (sub-zero) in pressure vessels, the ductility of metal diminishes and brittle fracture occurs while at high temperature in pressure vessels, embitterment of material may take place. 7. (a) (b) (c) (d)
X-rays are positively charged. negatively charged. neutral. (Ans) of higher wavelength than visible light.
8. (a) (b) (c) (d)
............. cycle is the most efficient thermodynamic cycle. Diesel Otto Rankine Carnot (Ans)
9. (a) (b) (c) (d)
What is the pH of distilled water? 0 1 7 (Ans) 14
10. The hydraulic radius of a circular pipe of diameter 'd' flowing full is (a) d/4 (Ans) (b) d/2 (c) 2d/3 (d) d/3 11. ........... number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical. (a) Mach (b) Reynolds (c) Froude (Ans) (d) Weber 12. The factor of safety for brittle materials (having elongation <5%) is based on the ----stress. (a) yield (b) proof (c) ultimate (Ans) (d) none of these 13. Which of the following is the terminology used for the temperature at which the phase changes occur in a metal ? (a) Critical temperature. (Ans) (b) Recrystallisation temperature. (c) Phase transformation temperature. (d) Transition temperature. 14. ...... has the highest melting point out of the following. (a) Tungsten (Ans) (b) Zirconium (c) Molybdenum (d) Tantalum 15. Gantt charts are used for streamlining the (a) inventory control (b) production schedule (Ans) (c) sales forecasting (d) quality control 16. Plasma is (a) (b) (c) (d)
a high temperature nothing but ionised a source of steady formed at very low
neutral gas. gas. (Ans) and highest controllable pressure. temperature.
17. In a fuel cell, chemical energy is converted into (a) electrical energy directly. (Ans) (b) mechanical energy. (c) electrical energy and stored therein. (d) none of these. 18. While the bin cards are used in the effective stores management, the queing theory is associated with the ..... time. (a) waiting (Ans) (b) idle
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
3/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
(c) inspection (d) tool replacement 19. Minimum diameter of the tube used for making water manometer should be ....... mm to avoid a correction for the effect of capillarity. (a) 1 (b) 2.5 (c) 4 (d) 6 (Ans) 20. Cobalt - 60 is used as a source of ...... in medical therapy & industrial radiography. (a) X-rays (b) g-rays (Ans) (c) a-rays (d) β-rays 21. An example of unsteady non uniform flow is the flow of liquid under pressure through a (a) tapering pipe at constant flow rate. (b) tapering pipe at either decreasing or increasing flow rate. (Ans) (c) long pipeline of constant diameter. (d) none of these. 22. Which of the following is not an explosive ? (a) TNT (b) CMC (Ans) (c) RDX (d) Lead azide 23. The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (a) rigid (b) tough (c) ductile (Ans) (d) plastic 24. Permanent set in a material is produced by subjecting it to (a) triaxial loading. (b) fatigue loading. (c) stresses beyond the elastic limit. (Ans) (d) tensile & compressive loads simultaneously. 25. ............. wire is never used for making the heating element. (a) Nichrome (b) Kanthal (c) Invar (Ans) (d) None of these 26. Milligram of KOH required to saponify 1 gm of oil is called its ..... number. (a) saponification (Ans) (b) acid (c) precipitation (d) emulsion 27. Ester is formed, when an alcohol reacts with (a) carboxylic acid (Ans) (b) aldehyde (c) ketone (d) ether 28. Adhesives (a) can't be used in the form of pressure sensitive tapes. (b) can't join two dissimilar metals. (c) cure instantaneously after application on a surface. (d) none of these. (Ans) 29. The process of removal of scale formed during hot rolling of steel is termed as (a) descaling (b) short blasting (c) pickling (Ans) (d) skimming 30. Out of the following, the joint produced by ............ has the lowest strength. (a) soldering (Ans) (b) welding (c) brazing (d) rivetting 31. With increase in carbon percentage in steel, its (a) yield (b) elongation percent increases. (c) tensile strength increases. (Ans) (d) impact strength increases. 32. The tensile strength of plastics ranges from .......... kg/mm2. (a) 10 to 50
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
4/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
(b) 50 to 100 (c) 0.01 to 0.1 (d) 0.1 to 10 (Ans) 33. Which of the following is a synthetic abrasive ? (a) Corundum (b) Emery (c) Pumice (d) Silicon carbide (Ans) 34. A good abrasive (a) should be friable. (Ans) (b) should have low refractoriness. (c) is made up of large size of crystals. (d) should be soft. 35. Thermoplastics are never moulded using (a) injection moulding (b) blow moulding (c) extrusion (d) compression moulding (Ans) 36. Which of the following is not a ferromagnetic material ? (a) Nickel (b) Cobalt (c) Aluminium (Ans) (d) Iron 37. Common salt is produced from sea water in India generally by the ........... method. (a) freeze drying (b) solar evaporation (Ans) (c) electrolytic (d) none of these 38. Young's modulus of a material is the measure of its (a) stiffness (Ans) (b) malleability (c) creep resistance (d) tensile strength 39. ..... test is the appropriate test to determine whether a material is ductile or brittle. (a) Impact (Ans) (b) Cupping (c) Hardness (d) Tensile 40. Which of the following is not an ore of iron ? (a) Chalcopyrite (Ans) (b) Magnetite (c) Hemetite (d) Limonite 41. Pig iron is (a) made from cast iron. (b) made from wrought iron. (c) the one, which comes out of the blast furnace. (d) free from impurities. 42. Annealing of cast iron (a) softens it to facilitate machining. (b) decreases the free carbon. (c) increase the strength. (d) none of these
(Ans)
(Ans)
43. L.D. (Linz-Donawitz) converter is used in the production of (a) copper (b) steel (Ans) (c) zinc (d) aluminium 44. ........ property of a material is determined by the Herbert Pendulum device. (a) Hardness (Ans) (b) Tensile (c) Toughness (d) Compressive 45. Galena is an ore of (a) iron (b) copper (c) lead (Ans) (d) aluminium 46. Chalcopyrite is an ore of (a) lead (b) aluminium
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
5/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
(c) copper (d) zinc
(Ans)
47. Aluminium is extracted from (a) chalcocite (b) bauxite (Ans) (c) galena (d) none of these 48. Oxygen content below .... percent in air contaminated with nitrogen does not support combustion and is unsafe for human exposure. (a) 18 (b) 16 (Ans) (c) 14 (d) 12 49. Area under the stress-strain curve upto the resilience. (a) yield strength (b) elastic limit (c) proportional limit (Ans) (d) maximum point
.... is referred to as the modulus of
50. The passage between the nozzle and the .......... is called 'sprue' in case of injection moulding. (a) runner (Ans) (b) cylinder (c) mold (d) none of these Found the similar paper in recruitment ? : Yes No You might also be interested in :GATE Placement Papers , Chemical-Engineering , Placement Papers By Company
Previous Papers
GATE/Placement-Paper-Electrical-Engineer...
Jobs
Placement Preparation
Career & Courses
JOBS BY CATEGORY
JOBS BY COURSES
SAMPLE PLACEMENT PAPERS
HIGHER STUDIES IN INDIA
TRAINING COURSES
IT / Software Jobs
BE / B.Tech Jobs
Placement Papers
M.Tech
Java / J2EE
Core Technical Jobs
MCA Jobs
Selection Procedure
MBA
PHP / MySQL
Government Sector Jobs
MBA / PGDM Jobs
Company Profiles
MCA
SEO / Web Designing
Defence Jobs
ME / M.Tech Jobs
Latest Papers
TEST PREPARATION
Assembly Language
Research Jobs
M.Sc Jobs
IT Companies
BPO Jobs
B.Com Jobs
Non IT Companies
MBA Jobs
BBA / BBM Jobs
Bank Papers
Dream Jobs> 5 lpa
BCA Jobs
Walk-ins Jobs
B.Sc Jobs
POWER PLACEMENT PREPARATION
BSc / BCA / BBM Jobs
Diploma Jobs
Aptitude Preparation
Teaching Jobs
Defence
JOBS BY CITIES
General Knowledge
1-3 Years Exp.Jobs
Civil Services
Ahmedabad Jobs
Interview Preparation Online Tests
STUDIES ABROAD
Bangalore Jobs Chennai Jobs
IT Companies Preparation
Delhi / NCR Jobs
GATE Preparation
Hyderabad Jobs
CAT Preparation
Kolkata Jobs
Bank Exam Preparation
Mumbai jobs
PSU Companies Preparation
Archived Job Job Results Internships Scholarships Success Stories
Pune Jobs
GRE GMAT CAT / MAT IELTS / TOEFL GATE
USA Australia UK New Zealand Canada Singapore
Android Development BlackBerry Development iPhone Development Mobile Testing Wireless Technology MicroSoft(MS) SQL Microsoft(MS) Access HTML / JavaSript / CSS / Ajax Joomla / Drupal / Wordpress ASP ASP.NET / C# C C++
List your Institute here
Candidate Services
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
6/7
1/29/14
GATE-Placement-Paper-Chemical-Engineering-44019
Freshersworld.com : The No.1 Jobsite for Freshers in India Freshersworld.com is the No.1 Jobsite for freshers in India with more than 3500+ top companies hiring through Freshersworld.com. Freshersworld is a one-stop shop for all your career needs, right from your campus interview preparation till the final selection in your dream company.
About Us
|
Blog
Terms of Use
|
|
FAQs
Privacy Policy
| |
Advertise With Us Copyright
|
Sitemap
|
Recruitment Solutions
|
Get in Touch
Contact Us
© 2000 - 2013 Freshersworld.com
placement.freshersworld.com/placement-papers/GATE/Placement-Paper-Chemical-Engineering-44019
7/7