FRGQ FRHB

LTE Radio Access, Rel. RL30, Operating Documentation, Issue 02, Doc Change Delivery 1

Flexi Multiradio BTS LTE RF Module and Remote Radio Head Description DN0951745 Issue 03B Approval Date 2011-11-22

Confidential

Flexi Multiradio BTS LTE RF Module and Remote Radio Head Description

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2011. All rights reserved

f

Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f

Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen. Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen. Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.

2

Id:0900d805808e9a1e Confidential

DN0951745 Issue 03B


Table of contents This document has 32 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

DN0951745

1

RF Module operation and main blocks . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2

Remote Radio Head operation and main blocks . . . . . . . . . . . . . . . . . . 11

3

RF Module and Remote Radio Head power requirements . . . . . . . . . . 18

4

RF Module and Remote Radio Head dimensions and weights . . . . . . . 20

5

RF Module interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6

Remote Radio Head interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7

RF Module and Remote Radio Head LED indications. . . . . . . . . . . . . . 31


3


List of figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18

4

Exploded view of the 3-sector RF Module . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional blocks of the 3-sector RF Module . . . . . . . . . . . . . . . . . . . . . 10 Isometric view of the Remote Radio Head (FHEA). . . . . . . . . . . . . . . . . 12 Isometric view of the Remote Radio Head (FRHB, FRMB) . . . . . . . . . . 13 Isometric view of the Remote Radio Head (FRLB) . . . . . . . . . . . . . . . . . 13 Isometric view of the Remote Radio Head (FRGQ) . . . . . . . . . . . . . . . . 14 Isometric view of the Remote Radio Head (FHCA) . . . . . . . . . . . . . . . . 15 Isometric view of the FHCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Front panel of the 3-sector RF Module (FRGP, FRIE, FRMA, FRBB) . . 23 RF Module (FXEA) front panel connectors and labels . . . . . . . . . . . . . . 23 RF Module (FXCA) front panel connectors and labels . . . . . . . . . . . . . . 24 Bottom view of the Remote Radio Head (FRGQ) . . . . . . . . . . . . . . . . . . 25 Bottom view of the Remote Radio Head (FRLB) . . . . . . . . . . . . . . . . . . 26 Bottom view of the Remote Radio Head (FRMB, FRHB) . . . . . . . . . . . . 27 Bottom view of the Remote Radio Head (FHEA) . . . . . . . . . . . . . . . . . . 28 Bottom view of the Remote Radio Head (FHCA) . . . . . . . . . . . . . . . . . . 29 Front view of the Remote Radio Head (FHCB). . . . . . . . . . . . . . . . . . . . 30 Rear view of the Remote Radio Head (FHCB) . . . . . . . . . . . . . . . . . . . . 30


DN0951745


List of tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Table 22 Table 23

DN0951745

RF Module versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 RF bandwidths for RF Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 RRH versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 RF bandwidths for Remote Radio Heads . . . . . . . . . . . . . . . . . . . . . . . 16 Input voltages of the RF Module and Remote Radio Head . . . . . . . . . 18 Power consumption of the RF Module . . . . . . . . . . . . . . . . . . . . . . . . . 18 Typical power consumption of the FRLB Remote Radio Head . . . . . . . 19 Typical power consumption of the FRHB Remote Radio Head . . . . . . 19 Typical power consumption of the FRGQ Remote Radio Head . . . . . . 19 Typical power consumption of the FHCA Remote Radio Head . . . . . . 19 Dimensions and weight of the RF Module . . . . . . . . . . . . . . . . . . . . . . 20 Dimensions and weight of the Remote Radio Heads . . . . . . . . . . . . . . 20 Dimensions and weight of the Remote Radio Heads (cont) . . . . . . . . . 20 RF Module front panel connectors, connector types and purposes . . . 22 Remote Radio Head interfaces (FRGQ) . . . . . . . . . . . . . . . . . . . . . . . . 25 Remote Radio Head interfaces (FRLB) . . . . . . . . . . . . . . . . . . . . . . . . 26 Remote Radio Head interfaces (FRMB, FRHB) . . . . . . . . . . . . . . . . . . 27 Remote Radio Head interfaces (FHEA) . . . . . . . . . . . . . . . . . . . . . . . . 28 Remote Radio Head interfaces (FHCA) . . . . . . . . . . . . . . . . . . . . . . . . 29 Remote Radio Head interfaces (FHCA) . . . . . . . . . . . . . . . . . . . . . . . . 30 RF Module core LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 RF Module fan LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Remote Radio Head RRH status LED indications . . . . . . . . . . . . . . . . 32


5

Summary of changes


Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. Changes between issues 03A (2011-09-17) and 03B (2011-11-22) FHCB Flexi RRH 2TX 850 low power for optical repeater interface feature added. Changes between issues 03 (2011-04-21) and 03A (2011-09-17) Section RF Module operation and main blocks has been updated with information on supported RF modules. Section Remote Radio Head operation and main blocks has been updated with information on supported RRHs. Section Remote Radio Head dimensions and weights has been updated. Changes between issues 02A (2011-03-25) and 03 (2011-04-21) Section RF Module operation and main blocks has been updated with information on supported RF modules. Section Remote Radio Head operation and main blocks has been updated with information on supported RRHs. Section Remote Radio Head dimensions and weights has been updated. Section Remote Radio Head interfaces has been updated. Section RF Module interfaces has been updated. Changes between issues 02 (2010-12-16) and 02A (2011-03-25) Section RF Module operation and main blocks has been updated with information on supported RF modules. Section Remote Radio Head operation and main blocks has been updated with information on supported RRHs.

6

Id:0900d805808ea131 Confidential

DN0951745


RF Module operation and main blocks

1 RF Module operation and main blocks The 3-sector RF Module is a stand-alone fully operational transceiver module with integrated antenna filters. The RF Module is able to support one to three sectors in a Flexi Multiradio base station. The RF Module hosts the RF functionality and provides control and power supply to the Flexi Antenna Line. Radio-related signal processing is performed in the RF Module. The RF Module has integrated fans and Bias-Ts.

f Incorrect cables and seals may not provide secured weather protection. In outdoor installations, including the outdoor cabinet, use only tested, at least IP55 class outdoor antenna jumper cables provided by Nokia Siemens Networks. This is also recommended for indoor installations. The following versions of the RF Module are available Flexi Multiradio BTS LTE: Version

Description

FRHA

Flexi 3-sector RF Module 2600 60W

FRGP


FRIE

Flexi 3-sector RF Module 1700/2100 60W

FRMA

Flexi 3-sector RF Module 800EU 60W

FRNA/B


FXEA


FXCA


Table 1

RF Module versions

RF Module operation See the following figures for exploded views of the RF Module.

DN0951745

Id:0900d805808a7708 Confidential

7


Figure 1


Exploded view of the 3-sector RF Module

The RF Module can support one to three sectors with the following integrated components: • • • • • • • • • • • •

8

Three transceivers with TX for two carriers Three transceivers with RX for two carriers with diversity (the carriers must be adjacent) Three linear power amplifiers Three RF filters with main and div branch 48 V DC input power supply Masthead amplifier and 3GPP Antenna tilt power feed and control for up to three sectors Interface to the System Module Interface for chaining System Modules Integrated fan assembly (two fans) Full operational bandwidth support Antenna connector interfaces Prepared for AISG2.0


DN0951745



The 3-sector RF Module has three independent transceivers each composed of one transmitter chain and two independent uplink chains to implement uplink diversity. The unit integrates an antenna filter unit that contains three filter blocks, each composed of one duplex filter (main antenna) and RX filter (diversity antenna), providing six antenna connectors for the BTS antenna line. The transceivers can be configured independently to dual or single carrier modes. The RF Module uses nominal 48 V DC for internal power supply. In case AISG2.0 is used the following versions of RF Modules use 12 V DC only: • • • • •

FRIE Core version A101 FRGP Core version A101 FXEA version A101 FXFA version A101 FXDA version A101

The VSWR monitoring system is used for producing alarms for the antenna line condition against alarm threshold (RRH and 3-sector RF Module). As a default setting, the minor alarm will be generated when the VSWR is 1.9 and major alarm (cell down) will be generated when the VSWR is 2.6. However, it is possible to adjust both minor and major alarm threshold between 1.5-3.5. In terms of H-type configuration the main and diversity branches are reversed for the middle sector (sector 2). RF bandwidths for the RF Module See the following table for RF bandwidths. Version FRGP

RF bandwidth TX: 20 MHz RX: 20 MHz

FRHA

TX: 20 MHz RX: 20 MHz

FRIE


FRMA


FRNA/B


FXCA


FXEA


Table 2

RF bandwidths for RF Modules

Functional blocks The RF Module includes the following functional blocks:

DN0951745


9


•

• • • •


RF control block: There are interfaces from the RF control block towards the System Module through optical connection. Most unit internal connections are made from the RF control block. Signal processing and unit control functionalities are located in this block. TX block: Analogue RF parts are located in the TX block. PA block: The power amplifier block amplifies TX block output signal to a specified output power level. RX block Antenna filter block: Antenna filtering for TX and RX signals is done in the Antenna filter block.

See the following figures for the functional blocks of the RF Module.

Figure 2

10

Functional blocks of the 3-sector RF Module


DN0951745


Remote Radio Head operation and main blocks

2 Remote Radio Head operation and main blocks The Remote Radio Head (RRH) is a stand-alone fully operational transceiver module with integrated antenna filters. The RRH supports one sector in a Flexi Multiradio base station. The RRH hosts the RF functionality and provides control and power supply to the Flexi Antenna Line. The RRH does not have any fans. Remote Radio Head types available: •

2 TX 2 RX

The following versions of the Remote Radio Head are available: Version

Description

FRMB

Flexi RRH 2TX 800EU 40W+40W

FHEA

Flexi RRH 2TX 1800 40W+40W

FRLB


FRHB


FRGQ


FHCA


Table 3

RRH versions

Remote Radio Head operation See the following figures for an isometric view of the Remote Radio Heads.

DN0951745


11


Figure 3

12


Isometric view of the Remote Radio Head (FHEA)


DN0951745


DN0951745


Figure 4

Isometric view of the Remote Radio Head (FRHB, FRMB)

Figure 5

Isometric view of the Remote Radio Head (FRLB)


13


Figure 6

14


Isometric view of the Remote Radio Head (FRGQ)


DN0951745


Figure 7


Isometric view of the Remote Radio Head (FHCA)

The Remote Radio Head hosts the RF functionality and provides control and power supply to Flexi Antenna Line. The Remote Radio Head has the following properties: • • •

DC power supply for 48 VDC Integrated Over Voltage Protection (OVP) External alarms

The RRH supports the VSWR monitoring system and is AISG2.0 compatible. It has two TX outputs that support a maximum of four TX carriers. RF bandwidths for the Remote Radio Head See the following table for RF bandwidths.

DN0951745


15



Version FRMB

RF bandwidth TX: 20 MHz RX: 30 MHz

FHEA


FRLB


FRHB


FRGQ


FHCA


Table 4

RF bandwidths for Remote Radio Heads

Functional blocks The RRH includes the following functional blocks: •

• • • •

RF control block: There are interfaces from the RF control block towards the System Module through optical connection. Most unit internal connections are made from the RF control block. Signal processing and unit control functionalities are located in this block. TX block: Analogue RF parts are located in the TX block. PA block: The power amplifier block amplifies TX block output signal to a specified output power level. RX block: the RX block includes two 2-carrier receivers. Antenna filter block: Antenna filtering for TX and RX signals is done in the Antenna filter block.

FHCB overview Indoor low power RRH optical repeater interface enables building LTE indoor and outdoor coverage using repeater solutions that is already known in customers legacy cdma systems.

16


DN0951745


Figure 8

DN0951745


Isometric view of the FHCB


17

RF Module and Remote Radio Head power requirements


3 RF Module and Remote Radio Head power requirements Input voltages and power consumption of the RF Module The input voltages and power consumption of the RF Module are described in the tables below. The fuse needed for the RF Module is in the System Module. See Flexi Multiradio BTS LTE System Module description for more information. Property

RF Module

RRH

Nominal supply voltage

48 V DC

48 V DC

Input voltage range

40.5 - 57 V DC

36 - 57 V DC

1)

1)

The minimum start-up voltage is 40.5 V.

Table 5

Input voltages of the RF Module and Remote Radio Head

Typical average RF Module power consumption at

3-sector RF Module

100 % RF load in 8 W mode

315 W


255 W


335 W


415 W


365 W


590 W


620 W


365 W


590 W


820 W

Maximum power consumption (60W mode) including extreme temperatures and power feeding to MHAs and tilting antennas via integraded Bias-Ts.

1120 W

Table 6

Power consumption of the RF Module

Maximum power consumption values consist of power feed to MHA + antenna tilt (3x30 W with the 3-sector RF Module). Up to 150 W higher power consumption can exist in extreme conditions and in BTS output power overdrive situations. In possible shortcircuit cases (for instance, antenna line) power consumption can momentarily be higher.

g

The values are given for the 2.1 GHz radio frequency (RF) module. For other RF module variants, power consumption can increase by a maximum of 10 %. Power consumption of the Remote Radio Head The table below lists the power consumption of the Remote Radio Head.

18


DN0951745


RF Module and Remote Radio Head power requirements

RF load

8 W mode

20 W mode

100%

181 W

239 W

321 W

50%

160 W

192 W

248 W

30%

159 W

170 W

213 W

10%

159 W

160 W

189 W

Table 7

30 W mode

Typical power consumption of the FRLB Remote Radio Head

RF load

8 W mode

20 W mode

100%

218 W

307 W

373 W

448 W

50%

183 W

235 W

275 W

321 W

30%

168 W

202 W

234 W

268 W

10%

161 W

165 W

189 W

211 W

Table 8

30 W mode

40 W mode

Typical power consumption of the FRHB Remote Radio Head

The following table presents the total estimated power consumption of the FRGQ including MHAs. load

20 W mode

100%

426 W

Table 9

30 W mode 481 W

537 W

Typical power consumption of the FRGQ Remote Radio Head

load

20 W mode

100%

220 W

350 W

50%

180 W

260 W

30%

160 W

220 W

10%

135 W

135 W

Table 10

40 W mode

40 W mode

Typical power consumption of the FHCA Remote Radio Head

Typical power consumption of FHCB is estimated at 70W not counting potential external load on 14.5V power supply.

DN0951745


19

RF Module and Remote Radio Head dimensions and weights


4 RF Module and Remote Radio Head dimensions and weights The tables below list the dimensions and weights of the RF Module and the Remote Radio Head. Property

3-sector RF Module

Height

133 mm/3U (5.2 in)

Width

447 mm (17.6 in)

Width (with covers)

492 mm (19.4 in)

Depth

560 mm (22 in)

Weight

25 kg

(including the core, fans and casing)

(55.1 lb)

Table 11

Dimensions and weight of the RF Module

f The module is heavy. Take care when lifting the module.

Property

FRGQ

FRMB/FRHB

FRLB

FHCA

Height

470 mm

514 mm

400 mm

450 mm

(18.50 in)

(20.27 in)

(15.75 in)

(17.72 in)

308 mm

326 mm

400 mm

290 mm

(12.13 in)

(12.83 in)

(15.75 in)

(11.42 in)

140 mm

148 mm

150 mm

tbd.

(5.51 in)

(5.83 in)

(5.90 in)

17.2 kg (without solar shield and mounting shroud)

17.3 kg (without solar shield and mounting shroud)

27 kg (without solar shield and mounting shroud)

15 kg (without solar shield and mounting shroud)

(37.92 lb)

(38.14 lb)

(59.52 lb)

(33.07 lb)

Width Depth Weight

Table 12

Dimensions and weight of the Remote Radio Heads

Property

FHCB

Height

1U

Table 13

20

Dimensions and weight of the Remote Radio Heads (cont)


DN0951745


Property

FHCB

Width

482.6 mm

RF Module and Remote Radio Head dimensions and weights

19 in Depth

450 mm (500 mm with mounting brackets)

Weight

Table 13

DN0951745

max. 15 kg\

Dimensions and weight of the Remote Radio Heads (cont) (Cont.)


21

RF Module interfaces


5 RF Module interfaces Front panel connectors The connectors on the front panel of the RF Module, their types and purposes are listed in the table below. Connector

Connector type

Purpose

Power supply

2-pin multibeam XL connector

Power delivery

Grounding

M8, 2 x M5

Grounding

Operational state visual indication

2 x tri-colour LED

Operational state and fan status indication

Antenna connector 1

7/16 type, female

RF signal interface to antenna(s)

Antenna connector 2

7/16 type, female


Antenna connector 3

7/16 type, female


Antenna connector 4

7/16 type, female


Antenna connector 5

7/16 type, female


Antenna connector 6

7/16 type, female


RX Out 1…3

QMA

RX signal to external output port

Optical interface

Duplex LC connector

Control interface to the System Module

Optical interface

Duplex LC connector

Chaining interface

Table 14

RF Module front panel connectors, connector types and purposes

See also section Lightning surge requirements in the Flexi Multiradio BTS LTE installation site requirements document. The 3-sector RF Modules front panesl are illustrated in the following figures.

22

Id:0900d8058087bf95 Confidential

DN0951745


Figure 9

PWR IN

LED Fan/TX Off status

Front panel of the 3-sector RF Module (FRGP, FRIE, FRMA, FRBB) ANT 6 ANT 5 RX RxO 5 TX/RX

DN0951745

ANT 3 ANT 4 RX RxO 3 TX/RX


OPT 2 OPT 1 OPT 3

Grounding points

LED Module status

Figure 10


EAC

RF Module (FXEA) front panel connectors and labels


23



PWR IN

ANT 6 RX RxO 6

TX/RX


RxO 5

LED Fan/TX Off status

Grounding points

LED Module status

Figure 11

24


RxO 3

RxO 1

OPT 2 OPT 1 OPT 3

EAC

RF Module (FXCA) front panel connectors and labels


DN0951745


Remote Radio Head interfaces

6 Remote Radio Head interfaces See the following tables and figures for Remote Radio Heads interfaces. Connector

Connector type

Purpose

Power supply

3-pole screw terminal

Power delivery

Grounding

M8, 2 x M5

Grounding


2 x LED

Operational state indication (Status: 3-colour LED, RF on: 2-colour LED)

Antenna connector (2 pcs)

7/16 type, female


Optical interface (2 pcs)

SFP


EAC connector

D-sub MDR14

External alarm

RET

8-pole circular

Remote electrical tilt

LMP

2x15 pin header

Local maintenance

RX Out (2 pcs)

SMA

RF external connector

Table 15

Remote Radio Head interfaces (FRGQ)

DC

GND

SFP

RX1 RET Figure 12

DN0951745

LED

LMP

EAC

RX2

ANT1

ANT2

Bottom view of the Remote Radio Head (FRGQ)


25


26


Connector

Connector type

Purpose

Power supply


Power delivery

Grounding

M8, 2 x M5

Grounding


2 x LED

Operational state indication (Status: 3-colour LED, RF on: 2-colour LED)


7/16 type, female



SFP


EAC connector

D-sub MDR14

External alarm

RET

8-pole circular


LMP

2x15 pin header

Local maintenance

RX Out (2 pcs)

QMA


Table 16

Remote Radio Head interfaces (FRLB)

Figure 13

Bottom view of the Remote Radio Head (FRLB)


DN0951745



Connector

Connector type

Purpose

Power supply


Power delivery

Grounding

M8, 2 x M5

Grounding


2 x LED

Operational state indication (Status: 3-colour LED)


7/16 type, female



SFP


RX Out (2 pcs)

SMA


EAC connector

MDR-14

External alarm

RET

8-pole circular


LMP

2x15 pin header

Local maintenance

Table 17

Remote Radio Head interfaces (FRMB, FRHB)

See also section Lightning surge requirements in the Flexi Multiradio BTS LTE installation site requirements document.

Figure 14

DN0951745

Bottom view of the Remote Radio Head (FRMB, FRHB)


27



Connector

Connector type

Purpose

Power supply


Power delivery

Grounding

M8, 2 x M5

Grounding


2 x LED



7/16 type, female



SFP


EAC connector

RJ45

External alarm

RET

8-pole circular


Table 18

Remote Radio Head interfaces (FHEA)

See also section Lightning surge requirements in the Flexi Multiradio BTS LTE installation site requirements document.

Figure 15

28

Bottom view of the Remote Radio Head (FHEA)


DN0951745



Connector

Connector type

Purpose

Power supply


Power delivery

Grounding

M8, 2 x M5

Grounding


2 x LED



7/16 type, female



SFP


EAC connector

RJ45

External alarm

RET

8-pin bulkhead connector


LMP

RJ45

Local maintenance

Table 19

Remote Radio Head interfaces (FHCA) SFP

DC

PWR +V48RTN

MAIN

OPT-1 OPT-2

-V48N

LMP

ANT 1

EAC

ANT 2

GND

Figure 16

DN0951745

RET

GND

Bottom view of the Remote Radio Head (FHCA)


29


30


Connector

Connector type

Purpose

Power supply


Power delivery

Transmitters

PSMP Smooth Bore

Connected to antenna

Receivers

PSMP Smooth Bore

Connected to external LNA

Pre-Distortion RX

PSMP Smooth Bore

-

External Alarm Connector

RJ45

External Equipment Alarm Lines

Optical interfacer

SFP connector + cage

System module, other RFM

14.5V Power Out

2x15 pin header

External LNA or other equipment as needed

LMP

2x15 pin header

Local maintenance

Table 20

Remote Radio Head interfaces (FHCA)

Figure 17

Front view of the Remote Radio Head (FHCB)

Figure 18

Rear view of the Remote Radio Head (FHCB)


DN0951745


RF Module and Remote Radio Head LED indications

7 RF Module and Remote Radio Head LED indications The RF Module and Remote Radio Head have two LEDs on the front panel to indicate the operational status of the module and all fault conditions during operation. Read the information on LED indications thoroughly. A blinking red LED does not always require removing the module. RF Module LED indications The RF Module LEDs are as follows: • •

one for the RF core functional block one for the fans in the RF Module

The LED indications of the RF Module are listed and explained in the tables below. Colour

Explanation

Red

Module self test or reset (LED red for < 5 second) or major alarm

Red, blinking

Minor alarm

Yellow

Module on and waiting or blocked

Yellow, blinking

SW download or configuration ongoing, module non-operational

Green

Module operational (cell can be locked in RNC)

Green, blinking

Module is loading software or parameters or local maintenance access when modules are operational

Table 21

RF Module core LED indications

In addition, the RF Module fan LED has an RF power ON/OFF display: LED mode

Explanation

Blinking

RF power off

Lit continuously

RF power on

Green

Fan is operational

Red

Fan is faulty

Table 22

RF Module fan LED indications

Remote Radio Head LED indications The Remote Radio Head has one LED indicating RRH status. The LED indications of the Remote Radio Head are listed and explained in the table below.

DN0951745

Id:0900d805807136bb Confidential

31

RF Module and Remote Radio Head LED indications


LED mode

Explanation

Red

Module self test or reset (LED red for < 5 second) or major alarm

Red, blinking

Minor alarm

Yellow

Module on and waiting or blocked

Yellow, blinking

SW download or configuration ongoing, module non-operational

Green

Module operational, OBSAI interface is synchronised

Green, blinking

Module is loading software or parameters

Table 23

Remote Radio Head RRH status LED indications

The RRHs do not have fans, therefore, there are no fan LEDs.

32

Id:0900d805807136bb Confidential

DN0951745

FRGQ FRHB

Recommend Documents