WCDMA RAN, Rel. WCDMA 16, Operating Documentation, Issue 06 Flexi Multiradio BTS RF Module and Remote Radio Head Description DN0951745 Issue 25 Approval Date 2017-01-24
Flexi Multiradio BTS RF Module and Remote Radio Head Description
The information in this document applies solely to the hardware/software product (“Product”) specified herein, and only as specified herein. Reference to “Nokia” later in this document shall mean the respective company within Nokia Group of Companies with whom you have entered into the Agreement (as defined below). This document is intended for use by Nokia's customers (“You”) only, and it may not be used except for the purposes defined in the agreement between You and Nokia (“Agreement”) under which this document is distributed. No part of this document may be used, copied, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia. If You have not entered into an Agreement applicable to the Product, or if that Agreement has expired or has been terminated, You may not use this document in any manner and You are obliged to return it to Nokia and destroy or delete any copies thereof. The document has been prepared to be used by professional and properly trained personnel, and You assume full responsibility when using it. Nokia welcomes your comments as part of the process of continuous development and improvement of the documentation. This document and its contents are provided as a convenience to You. Any information or statements concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on an “as is” and “as available” basis in this document, and Nokia reserves the right to change any such information and statements without notice. Nokia has made all reasonable efforts to ensure that the content of this document is adequate and free of material errors and omissions, and Nokia will correct errors that You identify in this document. Nokia's total liability for any errors in the document is strictly limited to the correction of such error(s). Nokia does not warrant that the use of the software in the Product will be uninterrupted or error-free. NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT. This document is Nokia proprietary and confidential information, which may not be distributed or disclosed to any third parties without the prior written consent of Nokia. Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document may be trademarks of their respective owners. Copyright © 2017 Nokia. All rights reserved.
f
Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.
Nokia is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia for any additional information.
2
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table of Contents This document has 424 pages
Summary of changes................................................................... 26
DN0951745 Issue: 25
1
RSS-310 compliance................................................................... 36
2
EU RoHS statement.....................................................................37
3
CE marking.................................................................................. 38
4
FCC Part 15 compliance.............................................................. 39
5
RF Performance...........................................................................40
6
Flexi RRHs Rel.4 compatibility with Nokia AirScale Radios.........41
7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 7.16 7.17 7.18 7.19
Descriptions of 3TX RF Modules................................................. 42 Flexi RF Module 3TX 800 (FRMA)...............................................42 Flexi RF Module 3TX 800 (FRMD)...............................................47 Flexi RFM 3-pipe 850 180 W (FXCA).......................................... 53 Flexi RF Module 3TX 900 (FXDA)............................................... 58 Flexi RFM 3-pipe 1500 180 W (FRKA)........................................ 64 Flexi RF Module 3TX 1800 (FXEA)..............................................70 Flexi RF Module 3TX 1900 (FXFB)..............................................76 Flexi RF Module 3TX 2100 (FRGP)............................................. 81 Flexi RF Module 3TX 2600 (FRHA)............................................. 87 Flexi RF Module 3TX 1700/2100 (FRIE)......................................92 Flexi RF Module 3TX 850 (FXCB)............................................... 98 Flexi RF Module 3TX 900 (FXDB)............................................. 104 Flexi RF Module 3TX 1800 (FXEB)............................................ 110 Flexi RFM 3-pipe 1800 240 W (FXEE)....................................... 116 Flexi RFM 3-pipe 1800 240 W (FXEF).......................................123 Flexi RF Module 3TX 1900 (FXFC)............................................130 Flexi RF Module 3TX 2100 (FRGT)........................................... 136 Flexi RF Module 3TX 2100 (FRGS)........................................... 142 Flexi RFM 3-pipe 2100 240 W (FRGX)...................................... 148
8 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8
Descriptions of 6TX RF Modules............................................... 156 Flexi RF Module 6TX 700 (FRPA)..............................................156 Flexi RF Module 6TX 700 (FRPB)............................................. 162 Flexi RFM 6-pipe 700 240 W (FRPD)........................................ 168 Flexi RF Module 6TX 2600 (FRHC)........................................... 174 Flexi RF Module 6TX 2600 (FRHF)........................................... 180 Flexi RF Module 6TX 800 (FRMC).............................................186 Flexi RFM 6-pipe 800 240 W (FRME)........................................192 Flexi RFM 6-pipe 800 360 W (FRMF)........................................ 198
© 2017 Nokia
3
Flexi Multiradio BTS RF Module and Remote Radio Head Description
4
8.9 8.10 8.11
Flexi RFM 6-pipe 1450 360 W (FRSA)...................................... 204 Flexi RFM 6-pipe 1800 360 W (FXED)...................................... 210 Flexi RFM 6-pipe 2100 360 W (FRGU)......................................217
9 9.1 9.2 9.3 9.4
Descriptions of Flexi Metro RRH................................................224 Flexi Metro RRH 2-pipe 900H 10 W (FHDG)............................. 224 Flexi Metro RRH 2-pipe 1800 10 W (FHEE).............................. 229 Flexi Metro RRH 2-pipe 1800L 10 W (FHEI)..............................233 Flexi Metro RRH 2-pipe 2100 10 W (FHGA)..............................238
10
Flexi Remote Radio Head 1TX 2100 (FRGG)............................244
11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 11.10 11.11 11.12
Descriptions of 2TX RRHs......................................................... 249 Flexi Remote Radio Head 2TX 850 (FHCA).............................. 249 Flexi Remote Radio Head 2TX 730 (FRLB)...............................254 Flexi RRH 2-pipe 900 80 W (FHDA).......................................... 259 Flexi Remote Radio Head 2TX 1800 (FHEA)............................ 264 Flexi Remote Radio Head 2TX 2100 (FRGQ)............................270 Flexi Remote Radio Head 2TX 2600 (FRHB)............................ 275 Flexi Remote Radio Head 2TX 800EU (FRMB).........................281 Flexi RRH 2-pipe 700/840 100 W (FHPC)................................. 286 Flexi Remote Radio Head 2TX 1800 (FHEB)............................ 292 Flexi RRH 2-pipe 1800 120 W (FHEF).......................................298 Flexi Remote Radio Head 2TX 900 (FHDB).............................. 304 Flexi RRH 2-pipe 1800 120 W (FHEG)...................................... 310
12 12.1 12.2 12.3 12.4
Descriptions of 4TX RRHs......................................................... 316 Flexi Remote Radio Head 4TX 1700/2100 (FRIG).................... 316 Flexi RRH 4-pipe 2100 120 W (FHGB)...................................... 322 Flexi Remote Radio Head 4TX 2600 (FRHD)............................ 329 Flexi Remote Radio Head 4TX 2600 (FRHE)............................ 334
13 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 13.11 13.12 13.13
Descriptions of RRHs Rel. 4.0................................................... 340 Flexi RRH 2-pipe 450 80 W (FRAA).......................................... 340 Flexi RRH 2-pipe 850 80 W (FRCC).......................................... 346 Flexi RRH 2-pipe 850 120 W (FRCG)........................................351 Flexi RRH 2-pipe 873 120 W (FRCJ).........................................357 Flexi RRH 2-pipe 875 120 W (FRCI)..........................................364 Flexi RRH 2-pipe 2100 120 W T (FRGB)...................................370 Flexi RRH 2-pipe 2100 120 W (FRGY)...................................... 376 Flexi RRH 4-pipe 720/730 160 W (FRBG)................................. 382 Flexi RRH 4-pipe 720/750 160 W (FRBE)................................. 389 Flexi RRH 4-pipe 1800 160 W (FHED)...................................... 395 Flexi RRH 4-pipe 1800 160 W (FHEH)...................................... 401 Flexi RRH 4-pipe 1900 160 W (FHFB).......................................407 Flexi RRH 4-pipe 2600 160 W (FRHG)......................................413
14
Compliance with EMC, RF and safety....................................... 420
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
15
Avoiding Passive Intermodulation during RF Module and RRH operation.................................................................................... 424
© 2017 Nokia
5
Flexi Multiradio BTS RF Module and Remote Radio Head Description
List of Figures
6
Figure 1
List of countries respecting EU Directive 2014/53/EU........................38
Figure 2
FRMA interfaces.................................................................................42
Figure 3
FRMA functional block diagram..........................................................43
Figure 4
FRMD interfaces.................................................................................48
Figure 5
FRMD functional block diagram......................................................... 49
Figure 6
FXCA interfaces................................................................................. 53
Figure 7
FXCA functional block diagram.......................................................... 55
Figure 8
FXDA interfaces................................................................................. 59
Figure 9
FXDA functional block diagram.......................................................... 60
Figure 10
FRKA interfaces................................................................................. 65
Figure 11
FRKA functional block diagram.......................................................... 66
Figure 12
FXEA interfaces..................................................................................70
Figure 13
FXEA functional block diagram.......................................................... 72
Figure 14
FXFB interfaces..................................................................................77
Figure 15
FXFB functional block diagram...........................................................78
Figure 16
FRGP interfaces................................................................................. 82
Figure 17
FRGP functional block diagram..........................................................83
Figure 18
FRHA interfaces................................................................................. 88
Figure 19
FRHA functional block diagram.......................................................... 89
Figure 20
FRIE interfaces...................................................................................93
Figure 21
FRIE functional block diagram............................................................94
Figure 22
FXCB interfaces................................................................................. 99
Figure 23
FXCB functional block diagram........................................................ 100
Figure 24
FXDB interfaces............................................................................... 105
Figure 25
FXDB functional block diagram........................................................ 106
Figure 26
FXEB interfaces................................................................................ 111
Figure 27
FXEB functional block diagram.........................................................112
Figure 28
FXEE interfaces................................................................................ 117
Figure 29
FXEE functional block diagram.........................................................119
Figure 30
FXEF interfaces................................................................................124
Figure 31
FXEF functional block diagram.........................................................126
Figure 32
FXFC interfaces................................................................................131
Figure 33
FXFC functional block diagram........................................................ 132
Figure 34
FRGT interfaces............................................................................... 137
Figure 35
FRGT functional block diagram........................................................ 138
Figure 36
FRGS interfaces............................................................................... 143
Figure 37
FRGS functional block diagram........................................................145
Figure 38
FRGX interfaces............................................................................... 149
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Figure 39
FRGX functional block diagram........................................................151
Figure 40
FRPA interfaces................................................................................157
Figure 41
FRPA functional block diagram........................................................ 158
Figure 42
FRPB interfaces............................................................................... 163
Figure 43
FRPB functional block diagram........................................................ 164
Figure 44
FRPD interfaces............................................................................... 169
Figure 45
FRPD functional block diagram........................................................ 170
Figure 46
FRHC interfaces............................................................................... 175
Figure 47
FRHC functional block diagram........................................................176
Figure 48
FRHF interfaces............................................................................... 181
Figure 49
FRHF functional block diagram........................................................ 182
Figure 50
FRMC interfaces...............................................................................187
Figure 51
FRMC functional block diagram....................................................... 188
Figure 52
FRME interfaces...............................................................................193
Figure 53
FRME functional block diagram........................................................194
Figure 54
FRMF interfaces............................................................................... 199
Figure 55
FRMF functional block diagram........................................................200
Figure 56
FRSA interfaces............................................................................... 205
Figure 57
FRSA functional block diagram........................................................ 206
Figure 58
FXED interfaces................................................................................211
Figure 59
FXED functional block diagram........................................................ 212
Figure 60
FRGU interfaces...............................................................................218
Figure 61
FRGU functional block diagram........................................................219
Figure 62
FHDG interfaces...............................................................................225
Figure 63
FHDG functional block diagram........................................................226
Figure 64
FHEE interfaces............................................................................... 229
Figure 65
FHEE functional block diagram........................................................ 230
Figure 66
FHEI interfaces.................................................................................234
Figure 67
FHEI functional block diagram..........................................................235
Figure 68
FHGA interfaces............................................................................... 239
Figure 69
FHGA functional block diagram........................................................240
Figure 70
FRGG (471882A) interfaces.............................................................244
Figure 71
FRGG functional block diagram....................................................... 245
Figure 72
FHCA interfaces............................................................................... 249
Figure 73
FHCA functional block diagram........................................................ 250
Figure 74
FRLB interfaces................................................................................254
Figure 75
FRLB functional block diagram.........................................................256
Figure 76
FHDA interfaces............................................................................... 260
Figure 77
FHDA functional block diagram........................................................ 261
Figure 78
FHEA interfaces............................................................................... 265
© 2017 Nokia
7
Flexi Multiradio BTS RF Module and Remote Radio Head Description
8
Figure 79
FHEA functional block diagram........................................................ 266
Figure 80
FRGQ interfaces...............................................................................270
Figure 81
FRGQ functional block diagram....................................................... 272
Figure 82
FRHB interfaces............................................................................... 276
Figure 83
FRHB functional block diagram........................................................ 277
Figure 84
FRMB interfaces...............................................................................281
Figure 85
FRMB functional block diagram........................................................283
Figure 86
FHPC interfaces............................................................................... 287
Figure 87
FHPC functional block diagram........................................................ 288
Figure 88
FHEB interfaces............................................................................... 293
Figure 89
FHEB functional block diagram........................................................ 294
Figure 90
FHEF interfaces................................................................................299
Figure 91
FHEF functional block diagram........................................................ 300
Figure 92
FHDB interfaces............................................................................... 305
Figure 93
FHDB functional block diagram........................................................ 306
Figure 94
FHEG interfaces............................................................................... 311
Figure 95
FHEG functional block diagram........................................................312
Figure 96
FRIG interfaces................................................................................ 316
Figure 97
FRIG functional block diagram......................................................... 318
Figure 98
FHGB interfaces............................................................................... 323
Figure 99
FHGB functional block diagram........................................................325
Figure 100
FRHD interfaces............................................................................... 329
Figure 101
FRHD functional block diagram........................................................331
Figure 102
FRHE interfaces............................................................................... 335
Figure 103
FRHE functional block diagram........................................................ 336
Figure 104
FRAA interfaces............................................................................... 340
Figure 105
FRAA functional block diagram........................................................ 342
Figure 106
FRCC interfaces............................................................................... 346
Figure 107
FRCC functional block diagram........................................................348
Figure 108
FRCG interfaces...............................................................................352
Figure 109
FRCG functional block diagram........................................................353
Figure 110
FRCJ interfaces................................................................................358
Figure 111
FRCJ functional block diagram.........................................................360
Figure 112
FRCI interfaces.................................................................................365
Figure 113
FRCI functional block diagram......................................................... 366
Figure 114
FRGB interfaces............................................................................... 371
Figure 115
FRGB functional block diagram........................................................372
Figure 116
FRGY interfaces............................................................................... 377
Figure 117
FRGY functional block diagram........................................................378
Figure 118
FRBG interfaces............................................................................... 383
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Figure 119
FRBG functional block diagram........................................................385
Figure 120
FRBE interfaces............................................................................... 390
Figure 121
FRBE functional block diagram........................................................ 391
Figure 122
FHED interfaces............................................................................... 396
Figure 123
FHED functional block diagram........................................................ 397
Figure 124
FHEH interfaces............................................................................... 402
Figure 125
FHEH functional block diagram........................................................ 403
Figure 126
FHFB interfaces................................................................................408
Figure 127
FHFB functional block diagram........................................................ 409
Figure 128
FRHG interfaces...............................................................................414
Figure 129
FRHG functional block diagram........................................................415
© 2017 Nokia
9
Flexi Multiradio BTS RF Module and Remote Radio Head Description
List of Tables
10
Table 1
Releases covered by the document .................................................. 26
Table 2
FRMA functional specification............................................................ 42
Table 3
FRMA interfaces.................................................................................43
Table 4
FRMA ALD support............................................................................ 43
Table 5
FRMA electrical specifications............................................................44
Table 6
FRMA power consumption................................................................. 44
Table 7
Recommended FRMA power backoff in 256 QAM mode...................44
Table 8
FRMA installation and mechanical specifications...............................44
Table 9
FRMA dimensions and weight............................................................45
Table 10
FRMA environmental specifications................................................... 46
Table 11
FRMA LEDs........................................................................................46
Table 12
FRMD functional specification............................................................ 47
Table 13
FRMD interfaces.................................................................................48
Table 14
FRMD ALD support............................................................................ 48
Table 15
FRMD electrical specifications........................................................... 49
Table 16
FRMD power consumption................................................................. 50
Table 17
Recommended FRMD power backoff in 256 QAM mode.................. 50
Table 18
FRMD installation and mechanical specifications.............................. 50
Table 19
FRMD dimensions and weight............................................................51
Table 20
FRMD environmental specifications................................................... 51
Table 21
FRMD LEDs....................................................................................... 51
Table 22
FXCA functional specification.............................................................53
Table 23
FXCA interfaces................................................................................. 54
Table 24
FXCA ALD support............................................................................. 54
Table 25
FXCA electrical specifications............................................................ 55
Table 26
FXCA power consumption..................................................................55
Table 27
Recommended FXCA power backoff in 256 QAM mode................... 56
Table 28
FXCA installation and mechanical specifications............................... 56
Table 29
FXCA dimensions and weight............................................................ 56
Table 30
FXCA environmental specifications....................................................57
Table 31
FXCA LEDs........................................................................................ 57
Table 32
FXDA functional specification.............................................................59
Table 33
FXDA interfaces................................................................................. 59
Table 34
FXDA ALD support............................................................................. 60
Table 35
FXDA electrical specifications............................................................ 61
Table 36
FXDA power consumption..................................................................61
Table 37
Recommended FXDA power backoff in 256 QAM mode................... 61
Table 38
FXDA installation and mechanical specifications............................... 61
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 39
FXDA dimensions and weight............................................................ 62
Table 40
FXDA environmental specifications....................................................62
Table 41
FXDA LEDs........................................................................................ 62
Table 42
FRKA functional specification.............................................................64
Table 43
FRKA interfaces................................................................................. 65
Table 44
FRKA ALD support............................................................................. 65
Table 45
FRKA electrical specifications............................................................ 66
Table 46
FRKA power consumption..................................................................66
Table 47
Recommended FRKA power backoff in 256 QAM mode................... 67
Table 48
FRKA installation and mechanical specifications............................... 67
Table 49
FRKA dimensions and weight............................................................ 68
Table 50
FRKA environmental specifications....................................................68
Table 51
FRKA LEDs........................................................................................ 68
Table 52
FXEA functional specification............................................................. 70
Table 53
FXEA interfaces..................................................................................71
Table 54
FXEA ALD support............................................................................. 71
Table 55
FXEA electrical specifications............................................................ 72
Table 56
FXEA power consumption.................................................................. 73
Table 57
Recommended FXEA power backoff in 256 QAM mode................... 73
Table 58
FXEA installation and mechanical specifications............................... 73
Table 59
FXEA dimensions and weight.............................................................74
Table 60
FXEA environmental specifications.................................................... 74
Table 61
FXEA LEDs........................................................................................ 74
Table 62
FXFB functional specification............................................................. 76
Table 63
FXFB interfaces..................................................................................77
Table 64
FXFB ALD support............................................................................. 77
Table 65
FXFB electrical specifications.............................................................78
Table 66
FXFB power consumption.................................................................. 78
Table 67
Recommended FXFB power backoff in 256 QAM mode....................79
Table 68
FXFB installation and mechanical specifications................................79
Table 69
FXFB dimensions and weight.............................................................79
Table 70
FXFB environmental specifications.................................................... 80
Table 71
FXFB LEDs.........................................................................................80
Table 72
FRGP functional specification............................................................ 82
Table 73
FRGP interfaces................................................................................. 82
Table 74
FRGP ALD support.............................................................................83
Table 75
FRGP electrical specifications............................................................83
Table 76
FRGP power consumption................................................................. 84
Table 77
Recommended FRGP power backoff in 256 QAM mode................... 84
Table 78
FRGP installation and mechanical specifications...............................84
© 2017 Nokia
11
Flexi Multiradio BTS RF Module and Remote Radio Head Description
12
Table 79
FRGP dimensions and weight............................................................ 85
Table 80
FRGP environmental specifications................................................... 85
Table 81
FRGP LEDs........................................................................................85
Table 82
FRHA functional specification.............................................................87
Table 83
FRHA interfaces................................................................................. 88
Table 84
FRHA ALD support.............................................................................88
Table 85
FRHA electrical specifications............................................................ 89
Table 86
FRHA power consumption..................................................................89
Table 87
Recommended FRHA power backoff in 256 QAM mode................... 90
Table 88
FRHA installation and mechanical specifications............................... 90
Table 89
FRHA dimensions and weight............................................................ 90
Table 90
FRHA environmental specifications....................................................91
Table 91
FRHA LEDs........................................................................................ 91
Table 92
FRIE functional specification.............................................................. 93
Table 93
FRIE interfaces...................................................................................93
Table 94
FRIE ALD support.............................................................................. 94
Table 95
FRIE electrical specifications..............................................................95
Table 96
FRIE power consumption................................................................... 95
Table 97
Recommended FRIE power backoff in 256 QAM mode.....................95
Table 98
FRIE installation and mechanical specifications.................................95
Table 99
FRIE dimensions and weight..............................................................96
Table 100
FRIE environmental specifications..................................................... 96
Table 101
FRIE LEDs..........................................................................................97
Table 102
FXCB functional specification.............................................................98
Table 103
FXCB interfaces................................................................................. 99
Table 104
FXCB ALD support........................................................................... 100
Table 105
FXCB electrical specifications.......................................................... 100
Table 106
FXCB power consumption................................................................101
Table 107
Recommended FXCB power backoff in 256 QAM mode................. 101
Table 108
FXCB installation and mechanical specifications............................. 102
Table 109
FXCB dimensions and weight.......................................................... 102
Table 110
FXCB environmental specifications..................................................103
Table 111
FXCB LEDs...................................................................................... 103
Table 112
FXDB functional specification...........................................................104
Table 113
FXDB interfaces............................................................................... 105
Table 114
FXDB ALD support........................................................................... 106
Table 115
FXDB electrical specifications.......................................................... 106
Table 116
FXDB power consumption................................................................107
Table 117
Recommended FXDB power backoff in 256 QAM mode................. 107
Table 118
FXDB installation and mechanical specifications............................. 108
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 119
FXDB dimensions and weight.......................................................... 108
Table 120
FXDB environmental specifications..................................................109
Table 121
FXDB LEDs...................................................................................... 109
Table 122
FXEB functional specification........................................................... 110
Table 123
FXEB interfaces................................................................................ 111
Table 124
FXEB ALD support........................................................................... 112
Table 125
FXEB electrical specifications...........................................................112
Table 126
FXEB power consumption................................................................ 113
Table 127
Recommended FXEB power backoff in 256 QAM mode..................114
Table 128
FXEB installation and mechanical specifications..............................114
Table 129
FXEB dimensions and weight........................................................... 114
Table 130
FXEB environmental specifications.................................................. 115
Table 131
FXEB LEDs.......................................................................................115
Table 132
FXEE functional specification........................................................... 117
Table 133
FXEE interfaces................................................................................ 117
Table 134
FXEE ALD support........................................................................... 118
Table 135
FXEE electrical specifications...........................................................119
Table 136
FXEE power consumption................................................................ 120
Table 137
Recommended FXEE power backoff in 256 QAM mode................. 121
Table 138
FXEE installation and mechanical specifications............................. 121
Table 139
FXEE dimensions and weight...........................................................121
Table 140
FXEE environmental specifications.................................................. 122
Table 141
FXEE LEDs...................................................................................... 122
Table 142
FXEF functional specification........................................................... 124
Table 143
FXEF interfaces................................................................................124
Table 144
FXEF ALD support........................................................................... 125
Table 145
FXEF electrical specifications...........................................................126
Table 146
FXEF power consumption................................................................ 127
Table 147
FXEF installation and mechanical specifications..............................127
Table 148
FXEF dimensions and weight...........................................................128
Table 149
FXEF environmental specifications.................................................. 128
Table 150
FXEF LEDs.......................................................................................129
Table 151
FXFC functional specification........................................................... 130
Table 152
FXFC interfaces................................................................................131
Table 153
FXFC ALD support........................................................................... 131
Table 154
FXFC electrical specifications.......................................................... 132
Table 155
FXFC power consumption................................................................ 133
Table 156
Recommended FXFC power backoff in 256 QAM mode................. 133
Table 157
FXFC installation and mechanical specifications............................. 133
Table 158
FXFC dimensions and weight...........................................................134
© 2017 Nokia
13
Flexi Multiradio BTS RF Module and Remote Radio Head Description
14
Table 159
FXFC environmental specifications.................................................. 135
Table 160
FXFC LEDs...................................................................................... 135
Table 161
FRGT functional specification...........................................................136
Table 162
FRGT output power in RU40 release and onwards..........................137
Table 163
FRGT interfaces............................................................................... 137
Table 164
FRGT ALD support...........................................................................138
Table 165
FRGT electrical specifications.......................................................... 139
Table 166
FRGT power consumption................................................................139
Table 167
Recommended FRGT power backoff in 256 QAM mode................. 139
Table 168
FRGT installation and mechanical specifications............................. 140
Table 169
FRGT dimensions and weight.......................................................... 140
Table 170
FRGT environmental specifications..................................................141
Table 171
FRGT LEDs...................................................................................... 141
Table 172
FRGS functional specification.......................................................... 143
Table 173
FRGS output power in RU40............................................................143
Table 174
FRGS interfaces............................................................................... 144
Table 175
FRGS ALD support...........................................................................144
Table 176
FRGS electrical specifications..........................................................145
Table 177
FRGS power consumption............................................................... 145
Table 178
Recommended FRGS power backoff in 256 QAM mode................. 146
Table 179
FRGS installation and mechanical specifications.............................146
Table 180
FRGS dimensions and weight.......................................................... 146
Table 181
FRGS environmental specifications................................................. 147
Table 182
FRGS LEDs......................................................................................147
Table 183
FRGX functional specification.......................................................... 149
Table 184
FRGX interfaces............................................................................... 149
Table 185
FRGX ALD support...........................................................................150
Table 186
FRGX electrical specifications..........................................................151
Table 187
FRGX power consumption............................................................... 152
Table 188
FRGX installation and mechanical specifications.............................152
Table 189
FRGX dimensions and weight.......................................................... 153
Table 190
FRGX environmental specifications................................................. 153
Table 191
FRGX LEDs......................................................................................154
Table 192
FRPA functional specification........................................................... 156
Table 193
FRPA interfaces................................................................................157
Table 194
FRPA ALD support........................................................................... 157
Table 195
FRPA electrical specifications.......................................................... 158
Table 196
FRPA power consumption................................................................ 159
Table 197
Recommended FRPA power backoff in 256 QAM mode..................159
Table 198
FRPA installation and mechanical specifications............................. 159
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 199
FRPA dimensions and weight...........................................................160
Table 200
FRPA environmental specifications.................................................. 160
Table 201
FRPA LEDs...................................................................................... 160
Table 202
FRPB functional specification...........................................................162
Table 203
FRPB interfaces............................................................................... 163
Table 204
FRPB ALD support........................................................................... 163
Table 205
FRPB electrical specifications.......................................................... 164
Table 206
FRPB power consumption................................................................165
Table 207
Recommended FRPB power backoff in 256 QAM mode................. 165
Table 208
FRBP installation and mechanical specifications............................. 165
Table 209
FRPB dimensions and weight.......................................................... 166
Table 210
FRPB environmental specifications..................................................166
Table 211
FRPB LEDs...................................................................................... 166
Table 212
FRPD functional specification...........................................................168
Table 213
FRPD interfaces............................................................................... 169
Table 214
FRPD ALD support...........................................................................169
Table 215
FRPD electrical specifications.......................................................... 170
Table 216
FRPD power consumption................................................................171
Table 217
Recommended FRPD power backoff in 256 QAM mode................. 171
Table 218
FRPD installation and mechanical specifications............................. 171
Table 219
FRPD dimensions and weight.......................................................... 172
Table 220
FRPD environmental specifications..................................................172
Table 221
FRPD LEDs...................................................................................... 172
Table 222
FRHC functional specification.......................................................... 174
Table 223
FRHC interfaces............................................................................... 175
Table 224
FRHC ALD support...........................................................................175
Table 225
FRHC electrical specifications..........................................................176
Table 226
FRHC power consumption............................................................... 177
Table 227
Recommended FRHC power backoff in 256 QAM mode................. 177
Table 228
FRHC installation and mechanical specifications.............................177
Table 229
FRHC dimensions and weight.......................................................... 178
Table 230
FRHC environmental specifications................................................. 178
Table 231
FRHC LEDs......................................................................................178
Table 232
FRHF functional specification...........................................................180
Table 233
FRHF interfaces............................................................................... 181
Table 234
FRHF ALD support........................................................................... 181
Table 235
FRHF electrical specifications.......................................................... 182
Table 236
FRHF power consumption................................................................183
Table 237
Recommended FRHF power backoff in 256 QAM mode................. 183
Table 238
FRHF installation and mechanical specifications............................. 183
© 2017 Nokia
15
Flexi Multiradio BTS RF Module and Remote Radio Head Description
16
Table 239
FRHF dimensions and weight.......................................................... 184
Table 240
FRHF environmental specifications..................................................184
Table 241
FRHF LEDs...................................................................................... 184
Table 242
FRMC functional specification.......................................................... 186
Table 243
FRMC interfaces...............................................................................187
Table 244
FRMC ALD support.......................................................................... 187
Table 245
FRMC electrical specifications......................................................... 188
Table 246
FRMC power consumption............................................................... 189
Table 247
Recommended FRMC power backoff in 256 QAM mode................ 189
Table 248
FRMC installation and mechanical specifications............................ 189
Table 249
FRMC dimensions and weight..........................................................190
Table 250
FRMC environmental specifications................................................. 190
Table 251
FRMC LEDs..................................................................................... 190
Table 252
FRME functional specification.......................................................... 192
Table 253
FRME interfaces...............................................................................193
Table 254
FRME ALD support.......................................................................... 193
Table 255
FRME electrical specifications..........................................................194
Table 256
FRME power consumption............................................................... 195
Table 257
Recommended FRME power backoff in 256 QAM mode.................195
Table 258
FRME installation and mechanical specifications.............................195
Table 259
FRME dimensions and weight..........................................................196
Table 260
FRME environmental specifications................................................. 196
Table 261
FRME LEDs......................................................................................196
Table 262
FRMF functional specification.......................................................... 198
Table 263
FRMF interfaces............................................................................... 199
Table 264
FRMF ALD support...........................................................................199
Table 265
FRMF electrical specifications..........................................................200
Table 266
FRMF power consumption............................................................... 201
Table 267
Recommended FRMF power backoff in 256 QAM mode................. 201
Table 268
FRMF installation and mechanical specifications.............................201
Table 269
FRMF dimensions and weight.......................................................... 202
Table 270
FRMF environmental specifications................................................. 202
Table 271
FRMF LEDs......................................................................................203
Table 272
FRSA functional specification...........................................................204
Table 273
FRSA interfaces............................................................................... 205
Table 274
FRSA ALD support........................................................................... 205
Table 275
FRSA electrical specifications.......................................................... 206
Table 276
FRSA power consumption................................................................207
Table 277
Recommended FRSA power backoff in 256 QAM mode................. 207
Table 278
FRSA installation and mechanical specifications............................. 207
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 279
FRSA dimensions and weight.......................................................... 208
Table 280
FRSA environmental specifications..................................................208
Table 281
FRSA LEDs...................................................................................... 209
Table 282
FXED functional specification...........................................................210
Table 283
FXED interfaces................................................................................211
Table 284
FXED ALD support........................................................................... 212
Table 285
FXED electrical specifications.......................................................... 213
Table 286
FXED power consumption................................................................213
Table 287
Recommended FXED power backoff in 256 QAM mode................. 214
Table 288
FXED installation and mechanical specifications............................. 214
Table 289
FXED dimensions and weight.......................................................... 215
Table 290
FXED environmental specifications..................................................215
Table 291
FXED LEDs...................................................................................... 216
Table 292
FRGU functional specification.......................................................... 217
Table 293
FRGU interfaces...............................................................................218
Table 294
FRGU ALD support.......................................................................... 218
Table 295
FRGU electrical specifications..........................................................219
Table 296
FRGU power consumption............................................................... 220
Table 297
Recommended FRGU power backoff in 256 QAM mode.................220
Table 298
FRGU installation and mechanical specifications.............................220
Table 299
FRGU dimensions and weight..........................................................221
Table 300
FRGU environmental specifications................................................. 222
Table 301
FRGU LEDs......................................................................................222
Table 302
FHDG functional specification.......................................................... 224
Table 303
FHDG interfaces...............................................................................225
Table 304
FHDG ALD support.......................................................................... 225
Table 305
FHDG electrical specifications..........................................................226
Table 306
FHDG power consumption............................................................... 226
Table 307
FHDG installation and mechanical specifications.............................227
Table 308
FHDG dimensions and weight..........................................................227
Table 309
FHDG environmental specifications................................................. 227
Table 310
FHDG LEDs......................................................................................228
Table 311
FHEE functional specification...........................................................229
Table 312
FHEE interfaces............................................................................... 230
Table 313
FHEE ALD support........................................................................... 230
Table 314
FHEE electrical specifications.......................................................... 230
Table 315
FHEE power consumption................................................................231
Table 316
FHEE installation and mechanical specifications............................. 231
Table 317
FHEE dimensions and weight.......................................................... 232
Table 318
FHEE environmental specifications..................................................232
© 2017 Nokia
17
Flexi Multiradio BTS RF Module and Remote Radio Head Description
18
Table 319
FHEE LEDs...................................................................................... 232
Table 320
FHEI functional specification............................................................ 234
Table 321
FHEI interfaces.................................................................................234
Table 322
FHEI ALD support............................................................................ 235
Table 323
FHEI electrical specifications............................................................235
Table 324
FHEI power consumption................................................................. 236
Table 325
FHEI installation and mechanical specifications...............................236
Table 326
FHEI dimensions and weight............................................................237
Table 327
FHEI environmental specifications................................................... 237
Table 328
FHEI LEDs........................................................................................237
Table 329
FHGA functional specification.......................................................... 239
Table 330
FHGA interfaces............................................................................... 239
Table 331
FHGA ALD support...........................................................................240
Table 332
FHGA electrical specifications..........................................................240
Table 333
FHGA power consumption............................................................... 241
Table 334
FHGA installation and mechanical specifications.............................241
Table 335
FHGA dimensions and weight.......................................................... 242
Table 336
FHGA environmental specifications................................................. 242
Table 337
FHGA LEDs......................................................................................242
Table 338
FRGG functional specification.......................................................... 244
Table 339
FRGG (471882A) interfaces.............................................................245
Table 340
FRGG ALD support.......................................................................... 245
Table 341
FRGG electrical specifications......................................................... 246
Table 342
FRGG power consumption............................................................... 246
Table 343
FRGG installation and mechanical specifications............................ 246
Table 344
FRGG dimensions and weight..........................................................247
Table 345
FRGG environmental specifications................................................. 247
Table 346
FRGG LEDs..................................................................................... 247
Table 347
FHCA functional specification...........................................................249
Table 348
FHCA interfaces............................................................................... 250
Table 349
FHCA ALD support...........................................................................250
Table 350
FHCA electrical specifications.......................................................... 251
Table 351
FHCA power consumption................................................................251
Table 352
Recommended FHCA power backoff in 256 QAM mode................. 251
Table 353
FHCA installation and mechanical specifications............................. 251
Table 354
FHCA dimensions and weight.......................................................... 252
Table 355
FHCA environmental specifications..................................................252
Table 356
FHCA LEDs...................................................................................... 252
Table 357
FRLB functional specification........................................................... 254
Table 358
FRLB interfaces................................................................................255
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 359
FRLB ALD support........................................................................... 255
Table 360
FRLB electrical specifications...........................................................256
Table 361
FRLB power consumption................................................................ 256
Table 362
Recommended FRLB power backoff in 256 QAM mode..................256
Table 363
FRLB installation and mechanical specifications..............................257
Table 364
FRLB dimensions and weight...........................................................257
Table 365
FRLB environmental specifications.................................................. 257
Table 366
FRLB LEDs.......................................................................................258
Table 367
FHDA functional specification...........................................................259
Table 368
FHDA interfaces............................................................................... 260
Table 369
FHDA ALD support...........................................................................260
Table 370
FHDA electrical specifications.......................................................... 261
Table 371
FHDA power consumption................................................................261
Table 372
Recommended FHDA power backoff in 256 QAM mode................. 262
Table 373
FHDA installation and mechanical specifications............................. 262
Table 374
FHDA dimensions and weight.......................................................... 262
Table 375
FHDA environmental specifications..................................................262
Table 376
FHDA LEDs...................................................................................... 263
Table 377
FHEA functional specification...........................................................264
Table 378
FHEA interfaces............................................................................... 265
Table 379
FHEA ALD support........................................................................... 265
Table 380
FHEA electrical specifications.......................................................... 266
Table 381
FHEA power consumption................................................................267
Table 382
Recommended FHEA power backoff in 256 QAM mode................. 267
Table 383
FHEA installation and mechanical specifications............................. 267
Table 384
FHEA dimensions and weight.......................................................... 268
Table 385
FHEA environmental specifications..................................................268
Table 386
FHEA LEDs...................................................................................... 268
Table 387
FRGQ functional specification.......................................................... 270
Table 388
FRGQ interfaces...............................................................................271
Table 389
FRGQ ALD support.......................................................................... 271
Table 390
FRGQ electrical specifications......................................................... 272
Table 391
FRGQ power consumption............................................................... 272
Table 392
Recommended FRGQ power backoff in 256 QAM mode................ 272
Table 393
FRGQ installation and mechanical specifications............................ 273
Table 394
FRGQ dimensions and weight..........................................................273
Table 395
FRGQ environmental specifications................................................. 273
Table 396
FRGQ LEDs..................................................................................... 274
Table 397
FRHB functional specification...........................................................275
Table 398
FRHB interfaces............................................................................... 276
© 2017 Nokia
19
Flexi Multiradio BTS RF Module and Remote Radio Head Description
20
Table 399
FRHB ALD support...........................................................................276
Table 400
FRHB electrical specifications.......................................................... 277
Table 401
FRHB power consumption................................................................278
Table 402
Recommended FRHB power backoff in 256 QAM mode................. 278
Table 403
FRHB installation and mechanical specifications............................. 278
Table 404
FRHB dimensions and weight.......................................................... 279
Table 405
FRHB environmental specifications..................................................279
Table 406
FRHB LEDs...................................................................................... 279
Table 407
FRMB functional specification.......................................................... 281
Table 408
FRMB interfaces...............................................................................282
Table 409
FRMB ALD support.......................................................................... 282
Table 410
FRMB electrical specifications..........................................................283
Table 411
FRMB power consumption............................................................... 283
Table 412
Recommended FRMB power backoff in 256 QAM mode.................284
Table 413
FRMB installation and mechanical specifications.............................284
Table 414
FRMB dimensions and weight..........................................................284
Table 415
FRMB environmental specifications................................................. 284
Table 416
FRMB LEDs......................................................................................285
Table 417
FHPC functional specification...........................................................286
Table 418
FHPC interfaces............................................................................... 287
Table 419
FHPC ALD support...........................................................................288
Table 420
FHPC electrical specifications.......................................................... 289
Table 421
FHPC power consumption................................................................289
Table 422
FHPC installation and mechanical specifications............................. 289
Table 423
FHPC dimensions and weight.......................................................... 290
Table 424
FHPC environmental specifications..................................................290
Table 425
FHPC LEDs (RRH Status)................................................................290
Table 426
FHPC LEDs (TX Status)...................................................................291
Table 427
FHEB functional specification...........................................................292
Table 428
FHEB interfaces............................................................................... 293
Table 429
FHEB ALD support........................................................................... 293
Table 430
FHEB electrical specifications.......................................................... 294
Table 431
FHEB power consumption................................................................295
Table 432
Recommended FHEB power backoff in 256 QAM mode................. 295
Table 433
FHEB installation and mechanical specifications............................. 295
Table 434
FHEB dimensions and weight.......................................................... 296
Table 435
FHEB environmental specifications..................................................296
Table 436
FHEB LEDs...................................................................................... 297
Table 437
FHEF functional specification........................................................... 298
Table 438
FHEF interfaces................................................................................299
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 439
FHEF ALD support........................................................................... 299
Table 440
FHEF electrical specifications.......................................................... 300
Table 441
FHEF power consumption................................................................ 301
Table 442
FHEF installation and mechanical specifications............................. 301
Table 443
FHEF dimensions and weight...........................................................302
Table 444
FHEF environmental specifications.................................................. 302
Table 445
FHEF LEDs...................................................................................... 303
Table 446
FHDB functional specification...........................................................304
Table 447
FHDB interfaces............................................................................... 305
Table 448
FHDB ALD support...........................................................................305
Table 449
FHDB electrical specifications.......................................................... 306
Table 450
FHDB power consumption................................................................307
Table 451
Recommended FHDB power backoff in 256 QAM mode................. 307
Table 452
FHDB installation and mechanical specifications............................. 308
Table 453
FHDB dimensions and weight.......................................................... 308
Table 454
FHDB environmental specifications..................................................309
Table 455
FHDB LEDs...................................................................................... 309
Table 456
FHEG functional specification.......................................................... 310
Table 457
FHEG interfaces............................................................................... 311
Table 458
FHEG ALD support...........................................................................312
Table 459
FHEG electrical specifications..........................................................312
Table 460
FHEG power consumption............................................................... 313
Table 461
FHEG installation and mechanical specifications.............................313
Table 462
FHEG dimensions and weight.......................................................... 313
Table 463
FHEG environmental specifications................................................. 314
Table 464
FHEG LEDs......................................................................................314
Table 465
FRIG functional specification............................................................316
Table 466
FRIG interfaces................................................................................ 317
Table 467
FRIG ALD support............................................................................ 317
Table 468
FRIG electrical specifications........................................................... 318
Table 469
FRIG power consumption.................................................................319
Table 470
FRIG installation and mechanical specifications.............................. 319
Table 471
FRIG dimensions and weight........................................................... 320
Table 472
FRIG environmental specifications...................................................320
Table 473
FRIG LEDs....................................................................................... 320
Table 474
FHGB functional specification.......................................................... 322
Table 475
FHGB interfaces............................................................................... 323
Table 476
FHGB ALD support...........................................................................324
Table 477
FHGB electrical specifications..........................................................325
Table 478
FHGB power consumption............................................................... 326
© 2017 Nokia
21
Flexi Multiradio BTS RF Module and Remote Radio Head Description
22
Table 479
Recommended FHGB power backoff in 256 QAM mode................. 326
Table 480
FHGB installation and mechanical specifications.............................326
Table 481
FHGB dimensions and weight.......................................................... 327
Table 482
FHGB environmental specifications................................................. 327
Table 483
FHGB LEDs......................................................................................327
Table 484
FRHD functional specification.......................................................... 329
Table 485
FRHD interfaces............................................................................... 330
Table 486
FRHD ALD support...........................................................................330
Table 487
FRHD electrical specifications..........................................................331
Table 488
FRHD power consumption............................................................... 332
Table 489
FRHD installation and mechanical specifications.............................332
Table 490
FRHD dimensions and weight.......................................................... 332
Table 491
FRHD environmental specifications................................................. 333
Table 492
FRHD LEDs......................................................................................333
Table 493
FRHE functional specification...........................................................334
Table 494
FRHE interfaces............................................................................... 335
Table 495
FRHE ALD support...........................................................................336
Table 496
FRHE electrical specifications.......................................................... 336
Table 497
FRHE power consumption................................................................337
Table 498
FRHE installation and mechanical specifications............................. 337
Table 499
FRHE dimensions and weight.......................................................... 337
Table 500
FRHE environmental specifications..................................................338
Table 501
FRHE LEDs...................................................................................... 338
Table 502
FRAA functional specification...........................................................340
Table 503
FRAA interfaces............................................................................... 341
Table 504
FRAA ALD support........................................................................... 341
Table 505
FRAA electrical specifications.......................................................... 342
Table 506
FRAA power consumption................................................................342
Table 507
Recommended FRAA power backoff in 256 QAM mode................. 343
Table 508
FRAA installation and mechanical specifications............................. 343
Table 509
FRAA dimensions and weight.......................................................... 343
Table 510
FRAA environmental specifications..................................................344
Table 511
FRAA LEDs...................................................................................... 344
Table 512
FRCC functional specification.......................................................... 346
Table 513
FRCC interfaces............................................................................... 347
Table 514
FRCC ALD support...........................................................................347
Table 515
FRCC electrical specifications..........................................................348
Table 516
FRCC power consumption............................................................... 348
Table 517
FRCC installation and mechanical specifications.............................349
Table 518
FRCC dimensions and weight.......................................................... 349
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 519
FRCC environmental specifications................................................. 350
Table 520
FRCC LEDs......................................................................................350
Table 521
FRCG functional specification.......................................................... 351
Table 522
FRCG interfaces...............................................................................352
Table 523
FRCG ALD support.......................................................................... 353
Table 524
FRCG electrical specifications..........................................................353
Table 525
FRCG power consumption............................................................... 354
Table 526
Recommended FRCG power backoff in 256 QAM mode.................354
Table 527
FRCG installation and mechanical specifications.............................354
Table 528
FRCG dimensions and weight..........................................................355
Table 529
FRCG environmental specifications................................................. 355
Table 530
FRCG LEDs......................................................................................356
Table 531
FRCJ functional specification........................................................... 357
Table 532
FRCJ interfaces................................................................................358
Table 533
FRCJ ALD support........................................................................... 358
Table 534
FRCJ electrical specifications...........................................................361
Table 535
FRCJ power consumption................................................................ 361
Table 536
FRCJ installation and mechanical specifications..............................361
Table 537
FRCJ dimensions and weight...........................................................362
Table 538
FRCJ environmental specifications.................................................. 362
Table 539
FRCJ LEDs.......................................................................................363
Table 540
FRCI functional specification............................................................ 364
Table 541
FRCI interfaces.................................................................................365
Table 542
FRCI ALD support............................................................................ 365
Table 543
FRCI electrical specifications........................................................... 366
Table 544
FRCI power consumption................................................................. 367
Table 545
FRCI installation and mechanical specifications.............................. 367
Table 546
FRCI dimensions and weight............................................................368
Table 547
FRCI environmental specifications................................................... 368
Table 548
FRCI LEDs....................................................................................... 369
Table 549
FRGB functional specification.......................................................... 370
Table 550
FRGB interfaces............................................................................... 371
Table 551
FRGB ALD support...........................................................................371
Table 552
FRGB electrical specifications..........................................................372
Table 553
FRGB power consumption............................................................... 373
Table 554
Recommended FRGB power backoff in 256 QAM mode................. 373
Table 555
FRGB installation and mechanical specifications.............................373
Table 556
FRGB dimensions and weight.......................................................... 374
Table 557
FRGB environmental specifications................................................. 374
Table 558
FRGB LEDs......................................................................................375
© 2017 Nokia
23
Flexi Multiradio BTS RF Module and Remote Radio Head Description
24
Table 559
FRGY functional specification.......................................................... 376
Table 560
FRGY interfaces............................................................................... 377
Table 561
FRGY ALD support...........................................................................377
Table 562
FRGY electrical specifications..........................................................378
Table 563
FRGY power consumption............................................................... 379
Table 564
Recommended FRGY power backoff in 256 QAM mode................. 379
Table 565
FRGY installation and mechanical specifications.............................379
Table 566
FRGY dimensions and weight.......................................................... 380
Table 567
FRGY environmental specifications................................................. 380
Table 568
FRGY LEDs......................................................................................381
Table 569
FRBG functional specification.......................................................... 382
Table 570
FRBG interfaces............................................................................... 383
Table 571
FRBG ALD support...........................................................................384
Table 572
FRBG electrical specifications..........................................................385
Table 573
FRBG power consumption............................................................... 386
Table 574
Recommended FRBG power backoff in 256 QAM mode................. 386
Table 575
FRBG installation and mechanical specifications.............................386
Table 576
FRBG dimensions and weight.......................................................... 387
Table 577
FRBG environmental specifications................................................. 387
Table 578
FRBG LEDs......................................................................................388
Table 579
FRBE functional specification...........................................................389
Table 580
FRBE interfaces............................................................................... 390
Table 581
FRBE ALD support........................................................................... 390
Table 582
FRBE electrical specifications.......................................................... 391
Table 583
FRBE power consumption................................................................392
Table 584
Recommended FRBE power backoff in 256 QAM mode................. 392
Table 585
FRBE installation and mechanical specifications............................. 392
Table 586
FRBE dimensions and weight.......................................................... 393
Table 587
FRBE environmental specifications..................................................393
Table 588
FRBE LEDs...................................................................................... 394
Table 589
FHED functional specification...........................................................395
Table 590
FHED interfaces............................................................................... 396
Table 591
FHED ALD support...........................................................................396
Table 592
FHED electrical specifications.......................................................... 397
Table 593
FHED power consumption................................................................398
Table 594
Recommended FHED power backoff in 256 QAM mode................. 398
Table 595
FHED installation and mechanical specifications............................. 398
Table 596
FHED dimensions and weight.......................................................... 399
Table 597
FHED environmental specifications..................................................399
Table 598
FHED LEDs...................................................................................... 400
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
DN0951745 Issue: 25
Table 599
FHEH functional specification...........................................................401
Table 600
FHEH interfaces............................................................................... 402
Table 601
FHEH ALD support...........................................................................402
Table 602
FHEH electrical specifications.......................................................... 403
Table 603
FHEH power consumption................................................................404
Table 604
Recommended FHEH power backoff in 256 QAM mode................. 404
Table 605
FHEH installation and mechanical specifications............................. 404
Table 606
FHEH dimensions and weight.......................................................... 405
Table 607
FHEH environmental specifications..................................................405
Table 608
FHEH LEDs...................................................................................... 406
Table 609
FHFB functional specification........................................................... 407
Table 610
FHFB interfaces................................................................................408
Table 611
FHFB ALD support........................................................................... 408
Table 612
FHFB electrical specifications.......................................................... 409
Table 613
FHFB power consumption................................................................ 410
Table 614
Recommended FHFB power backoff in 256 QAM mode................. 410
Table 615
FHFB installation and mechanical specifications............................. 410
Table 616
FHFB dimensions and weight........................................................... 411
Table 617
FHFB environmental specifications.................................................. 411
Table 618
FHFB LEDs...................................................................................... 412
Table 619
FRHG functional specification.......................................................... 413
Table 620
FRHG interfaces...............................................................................414
Table 621
FRHG ALD support.......................................................................... 414
Table 622
FRHG electrical specifications..........................................................415
Table 623
FRHG power consumption............................................................... 416
Table 624
Recommended FRHG power backoff in 256 QAM mode.................416
Table 625
FRHG installation and mechanical specifications.............................416
Table 626
FRHG dimensions and weight..........................................................417
Table 627
FRHG environmental specifications................................................. 417
Table 628
FRHG LEDs......................................................................................418
Table 629
Typical reference sensitivity degradation with different Antenna line PIM performance. ............................................................................ 424
© 2017 Nokia
25
Summary of changes
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. This document is common for all Radio Access Technologies (RAT). You may find here information about solutions that are not available or supported in a specific SW release or RAT. Table RAT releases covered by the document lists all SW releases covered by the content of this document. For features supported in your SW release, see respective feature documentation chapter in the system library. Table 1
Releases covered by the document Product
Release
GSM/EDGE (BSS)
GSM 16, GSM 17
WCDMA RAN
WCDMA 16, WCDMA 17
Long Term Evolution
FDD-LTE 15A, FDD-LTE 16, FDD-LTE 16A, FDD-LTE 17
Changes between issues 24 (2016-12-30) and 25 (2017-01-24) Flexi RF Module 3TX 800 (FRMA) •
Table 11: FRMA LEDs has been updated.
Flexi RF Module 3TX 800 (FRMD) •
Table 21: FRMD LEDs has been updated.
Flexi RFM 3-pipe 850 180 W (FXCA) •
Table 31: FXCA LEDs has been updated.
Flexi RFM 3-pipe 1500 180 W (FRKA) •
Table 51: FRKA LEDs has been updated.
Flexi RF Module 3TX 1900 (FXFB) •
Table 71: FXFB LEDs has been updated.
Flexi RF Module 3TX 2100 (FRGP) •
Table 81: FRGP LEDs has been updated.
Flexi RF Module 3TX 2600 (FRHA) •
Table 91: FRHA LEDs has been updated.
Flexi RF Module 3TX 1700/2100 (FRIE) •
Table 101: FRIE LEDs has been updated.
Flexi RF Module 3TX 850 (FXCB)
26
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
•
Summary of changes
Table 111: FXCB LEDs has been updated.
Flexi RF Module 3TX 900 (FXDB) •
Table 121: FXDB LEDs has been updated.
Flexi RF Module 3TX 1800 (FXEB) •
Table 131: FXEB LEDs has been updated.
Flexi RFM 3-pipe 1800 240 W (FXEE) •
Table 141: FXEE LEDs has been updated.
Flexi RFM 3-pipe 1800 240 W (FXEF) •
Table 150: FXEF LEDs has been updated.
Flexi RF Module 3TX 1900 (FXFC) •
Table 151: FXFC functional specification: DL instantaneous bandwidth has been updated.
Flexi RFM 3-pipe 900 240 W (FXJB) •
has been updated.
Flexi RF Module 3TX 2100 (FRGS) •
Table 182: FRGS LEDs has been updated.
Flexi RF Module 6TX 700 (FRPB) •
Table 211: FRPB LEDs has been updated.
Flexi RFM 6-pipe 700 240 W (FRPD) •
Table 221: FRPD LEDs has been updated.
Flexi RF Module 6TX 2600 (FRHC) •
Table 231: FRHC LEDs has been updated.
Flexi RF Module 6TX 800 (FRMC) •
Table 251: FRMC LEDs has been updated.
Flexi RFM 6-pipe 800 240 W (FRME) •
Table 261: FRME LEDs has been updated.
Flexi RFM 6-pipe 800 360 W (FRMF) •
Table 271: FRMF LEDs has been updated.
Flexi RFM 6-pipe 1450 360 W (FRSA) •
DN0951745 Issue: 25
Table 281: FRSA LEDs has been updated.
© 2017 Nokia
27
Summary of changes
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Flexi RFM 6-pipe 1800 360 W (FXED) •
Table 291: FXED LEDs has been updated.
Flexi RFM 6-pipe 2100 360 W (FRGU) •
Table 301: FRGU LEDs has been updated.
Flexi Metro RRH 2-pipe 900H 10 W (FHDG) •
Table 310: FHDG LEDs has been updated.
Flexi Metro RRH 2-pipe 1800 10 W (FHEE) •
Table 319: FHEE LEDs has been updated.
Flexi Metro RRH 2-pipe 1800L 10 W (FHEI) •
Table 328: FHEI LEDs has been updated.
Flexi Metro RRH 2-pipe 2100 10 W (FHGA) •
Table 337: FHGA LEDs has been updated.
Flexi Remote Radio Head 1TX 2100 (FRGG) •
Table 346: FRGG LEDs has been updated.
Flexi Remote Radio Head 2TX 850 (FHCA) •
Table 356: FHCA LEDs has been updated.
Flexi Remote Radio Head 2TX 730 (FRLB) •
Table 366: FRLB LEDs has been updated.
Flexi RRH 2-pipe 900 80 W (FHDA) •
Table 376: FHDA LEDs has been updated.
Flexi Remote Radio Head 2TX 1800 (FHEA) •
Table 386: FHEA LEDs has been updated.
Flexi Remote Radio Head 2TX 2100 (FRGQ) •
Table 396: FRGQ LEDs has been updated.
Flexi Remote Radio Head 2TX 2600 (FRHB) •
Table 406: FRHB LEDs has been updated.
Flexi Remote Radio Head 2TX 800EU (FRMB) •
Table 416: FRMB LEDs has been updated.
Flexi RRH 2-pipe 700/840 100 W (FHPC) •
28
Table 425: FHPC LEDs (RRH Status) has been updated.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Summary of changes
Flexi Remote Radio Head 2TX 1800 (FHEB) •
Table 436: FHEB LEDs has been updated.
Flexi RRH 2-pipe 1800 120 W (FHEF) •
Table 445: FHEF LEDs has been updated.
Flexi Remote Radio Head 2TX 900 (FHDB) •
Table 455: FHDB LEDshas been updated.
Flexi RRH 2-pipe 1800 120 W (FHEG) •
Table 464: FHEG LEDs has been updated.
Flexi Remote Radio Head 4TX 1700/2100 (FRIG) •
Table 473: FRIG LEDs has been updated.
Flexi RRH 4-pipe 2100 120 W (FHGB) •
Table 483: FHGB LEDs has been updated.
Flexi Remote Radio Head 4TX 2600 (FRHD) •
Table 492: FRHD LEDs has been updated.
Flexi Remote Radio Head 4TX 2600 (FRHE) •
Table 501: FRHE LEDs has been updated.
Flexi RRH 2-pipe 450 80 W (FRAA) •
Table 511: FRAA LEDs has been updated.
Flexi RRH 2-pipe 850 80 W (FRCC) •
Table 520: FRCC LEDs has been updated.
Flexi RRH 2-pipe 850 120 W (FRCG) •
Table 530: FRCG LEDs has been updated.
Flexi RRH 2-pipe 873 120 W (FRCJ) •
Table 539: FRCJ LEDs has been updated.
Flexi RRH 2-pipe 2100 120 W T (FRGB) •
Table 558: FRGB LEDs has been updated.
Flexi RRH 2-pipe 2100 120 W (FRGY) •
Table 568: FRGY LEDs has been updated.
Flexi RRH 4-pipe 720/730 160 W (FRBG) •
DN0951745 Issue: 25
Table 578: FRBG LEDs has been updated.
© 2017 Nokia
29
Summary of changes
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Flexi RRH 4-pipe 720/750 160 W (FRBE) •
Table 588: FRBE LEDs has been updated.
Flexi RRH 4-pipe 1800 160 W (FHED) •
Table 598: FHED LEDs has been updated.
Flexi RRH 4-pipe 1800 160 W (FHEH) •
Table 608: FHEH LEDs has been updated.
Flexi RRH 4-pipe 1900 160 W (FHFB) •
Table 618: FHFB LEDs has been updated.
Flexi RRH 4-pipe 2600 160 W (FRHG) •
Table 628: FRHG LEDs has been updated.
Changes between issues 23 (2016-12-19) and 24 (2016-12-30) Flexi RFM 3-pipe 2100 240 W (FRGX) •
Table 183: FRGX functional specification: FDD-LTE has been added to SW supported technology.
Changes between issues 22 (2016-09-21) and 23 (2016-12-19) Flexi RF Module 3TX 800 (FRMA) • •
Table 7: Recommended FRMA power backoff in 256 QAM mode has been added. Table 4: FRMA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 800 (FRMD) •
Table 14: FRMD ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 850 180 W (FXCA) • •
Table 27: Recommended FXCA power backoff in 256 QAM mode has been added. Table 24: FXCA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 900 (FXDA) • •
Table 37: Recommended FXDA power backoff in 256 QAM mode has been added. Table 34: FXDA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 1500 180 W (FRKA) • •
Table 47: Recommended FRKA power backoff in 256 QAM mode has been added. Table 44: FRKA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 1800 (FXEA)
30
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
• • •
Summary of changes
Table 57: Recommended FXEA power backoff in 256 QAM mode has been added. Table 54: FXEA ALD support: information on Proprietary AISG 1.1 has been removed. Table 56: FXEA power consumption has been updated.
Flexi RF Module 3TX 1900 (FXFB) •
Table 64: FXFB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 2100 (FRGP) • •
Table 77: Recommended FRGP power backoff in 256 QAM mode has been added. Table 74: FRGP ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 2600 (FRHA) • •
Table 87: Recommended FRHA power backoff in 256 QAM mode has been added. Table 84: FRHA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 1700/2100 (FRIE) • •
Table 97: Recommended FRIE power backoff in 256 QAM mode has been added. Table 94: FRIE ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 850 (FXCB) • •
Table 107: Recommended FXCB power backoff in 256 QAM mode has been added. Table 104: FXCB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 900 (FXDB) •
Table 114: FXDB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 1800 (FXEB) • •
Table 127: Recommended FXEB power backoff in 256 QAM mode has been added. Table 124: FXEB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 1800 240 W (FXEE) • •
Table 137: Recommended FXEE power backoff in 256 QAM mode has been added. Table 134: FXEE ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 1800 240 W (FXEF) •
DN0951745 Issue: 25
Table 144: FXEF ALD support: information on Proprietary AISG 1.1 has been removed.
© 2017 Nokia
31
Summary of changes
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Flexi RF Module 3TX 1900 (FXFC) • •
Table 156: Recommended FXFC power backoff in 256 QAM mode has been added. Table 153: FXFC ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 900 240 W (FXJB) •
: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 2100 (FRGT) • •
Table 167: Recommended FRGT power backoff in 256 QAM mode has been added. Table 164: FRGT ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 3TX 2100 (FRGS) •
Table 175: FRGS ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 3-pipe 2100 240 W (FRGX) •
Table 185: FRGX ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 6TX 700 (FRPA) • • •
Table 197: Recommended FRPA power backoff in 256 QAM mode has been added. Table 194: FRPA ALD support: information on Proprietary AISG 1.1 has been removed. Table 192: FRPA functional specification: information on certain software limitations has been added.
Flexi RF Module 6TX 700 (FRPB) • •
Table 207: Recommended FRPB power backoff in 256 QAM mode has been added. Table 204: FRPB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 6-pipe 700 240 W (FRPD) • •
Table 217: Recommended FRPD power backoff in 256 QAM mode has been added. Table 214: FRPD ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 6TX 2600 (FRHC) •
Table 224: FRHC ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RF Module 6TX 2600 (FRHF) • •
32
Table 237: Recommended FRHF power backoff in 256 QAM mode has been added. Table 234: FRHF ALD support: information on Proprietary AISG 1.1 has been removed.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Summary of changes
Flexi RF Module 6TX 800 (FRMC) •
Table 244: FRMC ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 6-pipe 800 240 W (FRME) •
Table 257: Recommended FRME power backoff in 256 QAM mode has been added.
Flexi RFM 6-pipe 1450 360 W (FRSA) • •
Table 277: Recommended FRSA power backoff in 256 QAM mode has been added. Table 274: FRSA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 6-pipe 1800 360 W (FXED) •
Table 284: FXED ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RFM 6-pipe 2100 360 W (FRGU) • •
Table 297: Recommended FRGU power backoff in 256 QAM mode has been added. Table 294: FRGU ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 1TX 2100 (FRGG) •
Table 340: FRGG ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 850 (FHCA) •
Table 349: FHCA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 730 (FRLB) •
Table 359: FRLB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 900 80 W (FHDA) • •
Table 372: Recommended FHDA power backoff in 256 QAM mode has been added. Table 369: FHDA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 1800 (FHEA) • •
Table 379: FHEA ALD support: information on Proprietary AISG 1.1 has been removed. Table 381: FHEA power consumption has been updated.
Flexi Remote Radio Head 2TX 2100 (FRGQ) •
DN0951745 Issue: 25
Table 389: FRGQ ALD support: information on Proprietary AISG 1.1 has been removed.
© 2017 Nokia
33
Summary of changes
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Flexi Remote Radio Head 2TX 2600 (FRHB) • •
Table 402: Recommended FRHB power backoff in 256 QAM mode has been added. Table 399: FRHB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 800EU (FRMB) • •
Table 412: Recommended FRMB power backoff in 256 QAM mode has been added. Table 409: FRMB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 1800 (FHEB) • •
Table 432: Recommended FHEB power backoff in 256 QAM mode has been added. Table 429: FHEB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 1800 120 W (FHEF) •
Table 439: FHEF ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 2TX 900 (FHDB) •
Table 448: FHDB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 1800 120 W (FHEG) •
Table 458: FHEG ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 4TX 1700/2100 (FRIG) • •
Table 467: FRIG ALD support: information on Proprietary AISG 1.1 has been removed. Table 469: FRIG power consumption has been updated.
Flexi Remote Radio Head 4TX 2600 (FRHD) •
Table 486: FRHD ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi Remote Radio Head 4TX 2600 (FRHE) •
Table 495: FRHE ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 450 80 W (FRAA) • •
Table 507: Recommended FRAA power backoff in 256 QAM mode has been added. Table 504: FRAA ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 850 120 W (FRCG)
34
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
•
Summary of changes
Table 526: Recommended FRCG power backoff in 256 QAM mode has been added.
Flexi RRH 2-pipe 873 120 W (FRCJ) •
Table 533: FRCJ ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 2100 120 W T (FRGB) •
Table 551: FRGB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 2-pipe 2100 120 W (FRGY) • •
Table 564: Recommended FRGY power backoff in 256 QAM mode has been added. Table 561: FRGY ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 4-pipe 720/750 160 W (FRBE) •
Table 584: Recommended FRBE power backoff in 256 QAM mode has been added.
Flexi RRH 4-pipe 1800 160 W (FHED) • •
Table 594: Recommended FHED power backoff in 256 QAM mode has been added. Table 591: FHED ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 4-pipe 1800 160 W (FHEH) • •
Table 604: Recommended FHEH power backoff in 256 QAM mode has been added. Table 601: FHEH ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 4-pipe 1900 160 W (FHFB) •
Table 611: FHFB ALD support: information on Proprietary AISG 1.1 has been removed.
Flexi RRH 4-pipe 2600 160 W (FRHG) • •
DN0951745 Issue: 25
Table 624: Recommended FRHG power backoff in 256 QAM mode has been added Table 621: FRHG ALD support: information on Proprietary AISG 1.1 has been removed.
© 2017 Nokia
35
RSS-310 compliance
Flexi Multiradio BTS RF Module and Remote Radio Head Description
1 RSS-310 compliance This equipment complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
36
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
EU RoHS statement
2 EU RoHS statement This equipment complies with the European Union RoHS Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment. The directive applies to the use of lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in electrical and electronic equipment.
DN0951745 Issue: 25
© 2017 Nokia
37
CE marking
Flexi Multiradio BTS RF Module and Remote Radio Head Description
3 CE marking Declaration of Conformity with Regard to the EU Directive 2014/53/EU (RED Directive) Hereby, Nokia declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive: 2014/53/EU. Figure 1
List of countries respecting EU Directive 2014/53/EU
RED Directive2014/53/EU AT
ü
FR
ü
LV
ü
LI
ü
BE
ü
DE
ü
LT
ü
RO
ü
BG
ü
GB
ü
LU
ü
SK
ü
CY
ü
GR
ü
MT
ü
SI
ü
CZ
ü
HU
ü
NL
ü
ES
ü
DK
ü
IS
ü
NO
ü
SE
ü
EE
ü
IE
ü
PL
ü
CH
ü
FI
ü
IT
ü
PT
ü
TR
ü
This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and/or supported by Nokia.
38
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FCC Part 15 compliance
4 FCC Part 15 compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference, in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manuals, might cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
DN0951745 Issue: 25
© 2017 Nokia
39
RF Performance
Flexi Multiradio BTS RF Module and Remote Radio Head Description
5 RF Performance The topic describes the radios RF sensitivity and TX output power tolerance. RF sensitivity Nokia Flexi radios have superior field proven RX sensitivity which correlates as top uplink performance without any compromises to the uplink coverage. Accuracy was maintained during the Uplink performance tests by following 3GPP standard 36.104 and using real commercial radio hardware units. The receiver sensitivity results of up to -106.6 dBm have been measured using commercial radio hardware under realistic circumstances, ultimately this produces accurate mean -106.3 dBm. TX output power tolerance Nokia Flexi radios power amplifier design brings benefits to the wider operating and instantaneous bandwidth radio units. This design produces a competitive output power tolerance which is less than +/-0.8dB. The benefit produces robust power amplifier design is the high maximum downlink throughput levels in real operating environments.
40
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Flexi RRHs Rel.4 compatibility with Nokia AirScale Radios
6 Flexi RRHs Rel.4 compatibility with Nokia AirScale Radios Flexi RRHs Rel.4 are compatible with Nokia AirScale Radio via conversion kit. Flexi RRHs Rel.4 have forward-compatibility with Nokia AirScale Radios. Using a conversion kit, Flexi RRH Rel.4 can be installed with AirScale Radio in a book mount option. The conversion kits are: • •
Corona 2T2R Book Mount HW Kit (FMFH) Corona 4T4R Book Mount HW Kit (FMFB)
FMFH and FMFB are optional items. For more information on AirScale Radios, see Nokia AirScale Radio Description DN09236379.
DN0951745 Issue: 25
© 2017 Nokia
41
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
7 Descriptions of 3TX RF Modules 7.1 Flexi RF Module 3TX 800 (FRMA) FRMA technical specifications. Functional description Table 2
FRMA functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
791-821 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces Figure 2
FRMA interfaces
RXO3 ANT6 RX
DCIN
ANT4 RX
ANT2 RX
RXO2
ANT5 TX/RX
Ground
ANT3 TX/RX
OPT 1
ANT1 TX/RX
RXO1
OPT 3
OPT2
42
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 3
Descriptions of 3TX RF Modules
FRMA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 4
FRMA ALD support ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 24 V
Power per port
30 W
Functional block diagram Figure 3
FRMA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
PA
TXRX
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
DN0951745 Issue: 25
© 2017 Nokia
43
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Electrical specifications Table 5
FRMA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 6
FRMA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
Table 7
100% RF Load
60
669
943
40
510
673
20
374
450
Recommended FRMA power backoff in 256 QAM mode Single carrier [dB]
0.9
Dual carrier [dB] 1.3
Installation and mechanical specifications Table 8
FRMA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
FRMA includes casing
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Pole installation
44
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 8
Descriptions of 3TX RF Modules
FRMA installation and mechanical specifications (Cont.) Property
Value
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Pole Mounting Kit (VMPB)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Covers for Back and Front (FMCx)
Outdoor 19'' rack •
Flexi Mounting Covers for Back and Front (FMCx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 9
FRMA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.)
Width
Dimensions orientation
height width
depth
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications
DN0951745 Issue: 25
© 2017 Nokia
45
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 10
FRMA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 11
FRMA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
46
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 11
Descriptions of 3TX RF Modules
FRMA LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.2 Flexi RF Module 3TX 800 (FRMD) FRMD technical specifications. Functional description Table 12
FRMD functional specification Property
DN0951745 Issue: 25
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
791-806 MHz
RX frequency range
832-847 MHz
© 2017 Nokia
47
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 12
FRMD functional specification (Cont.) Property
Value
DL instantaneous bandwidth
15 MHz
UL instantaneous bandwidth
15 MHz
DL filter bandwidth
15 MHz
UL filter bandwidth
15 MHz
Interfaces Figure 4
FRMD interfaces
ANT4 RX
RXO3 ANT6 RX
RXO2
ANT5 TX/RX
DCIN
ANT2 RX
ANT3 TX/RX
Ground
ANT1 TX/RX
RXO1
OPT 1
OPT 3
OPT2 Table 13
FRMD interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 14
FRMD ALD support
ALD support via antenna ports
48
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
No
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 14
Descriptions of 3TX RF Modules
FRMD ALD support (Cont.)
ALD support via antenna ports
Value
Voltage
ANT1, ANT3, ANT5: 24 V
Power per port
30 W
Functional block diagram Figure 5
FRMD functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RXDiversity
RF control
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 15
FRMD electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
49
Descriptions of 3TX RF Modules
Table 16
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRMD power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
Table 17
100% RF Load
60
621
826
40
486
616
20
369
435
Recommended FRMD power backoff in 256 QAM mode Single carrier [dB]
1.0
Dual carrier [dB] 1.5
Installation and mechanical specifications Table 18
FRMD installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight
50
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 19
Descriptions of 3TX RF Modules
FRMD dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.)
Dimensions orientation
height
With front covers: 560 mm (22.1 in.) Width
depth
width
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 20
FRMD environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 21
FRMD LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
© 2017 Nokia
No alarm
51
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 21
FRMD LEDs (Cont.) LED color
Description
Yellow, blinking
• •
Green, stable
•
•
Alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g 52
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
7.3 Flexi RFM 3-pipe 850 180 W (FXCA) FXCA technical specifications. Functional description Table 22
FXCA functional specification Property
Value
Output power
3x60 W
MIMO
No
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
869-894 MHz 30x version: 852-894 MHz
RX frequency range
824-849 MHz 30x version: 807-849 MHz
DL instantaneous bandwidth
15 MHz, 18 MHz in GSM dedicated mode
UL instantaneous bandwidth
15 MHz, 18 MHz in GSM dedicated mode
DL filter bandwidth
15 MHz, 18 MHz in GSM dedicated mode
UL filter bandwidth
15 MHz, 18 MHz in GSM dedicated mode
Interfaces Figure 6
FXCA interfaces ANT6 RX
PWRIN
ANT5 TX/RX RxO6
ANT4 RX
ANT2 RX
RxO4 ANT3 TX/RX
RxO5 RxO3
LED Fan/TXOff status LEDModule status
DN0951745 Issue: 25
EAC Grounding points
© 2017 Nokia
ANT1 TX/RX
RxO2 RxO1
OPT1
OPT3 OPT2
53
Descriptions of 3TX RF Modules
Table 23
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXCA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 24
FXCA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V
Power per port
30 W
Functional block diagram
54
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 7
Descriptions of 3TX RF Modules
FXCA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
Rx
RX filter
RXDiversity
RET
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF
RF control
OpticalIF
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
LNA
PA
TXRX
DCIN
TX filter
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 25
FXCA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 26
FXCA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
DN0951745 Issue: 25
100% RF Load
60
545
794
40
468
644
20
393
494
© 2017 Nokia
55
Descriptions of 3TX RF Modules
Table 27
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FXCA power backoff in 256 QAM mode Single carrier [dB]
Dual carrier [dB]
0.1
0.5
Installation and mechanical specifications Table 28
FXCA installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 29
FXCA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.)
Width
56
Dimensions orientation
height width
depth
Without front covers: 447 mm (17.6 in.)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 29
Descriptions of 3TX RF Modules
FXCA dimensions and weight (Cont.) Property
Value
Dimensions orientation
With front covers: 492 mm (19.4 in.) Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 30
FXCA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 31
FXCA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
DN0951745 Issue: 25
Alarm
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated
© 2017 Nokia
No alarm
57
Descriptions of 3TX RF Modules
Table 31
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXCA LEDs (Cont.) LED color
Description
•
Alarm
and transmission is possible Working normally, no alarm on the RF Module
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.4 Flexi RF Module 3TX 900 (FXDA) FXDA technical specifications. Functional description
58
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 32
Descriptions of 3TX RF Modules
FXDA functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
925-960 MHz
RX frequency range
880-915 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
20 MHz
Interfaces Figure 8
FXDA interfaces RxO3
RxO5 PWRIN
ANT6 RX
ANT5 TX/RX
ANT4 RX
RxO1 ANT3 TX/RX
EAC LED Fan/TXOff status
OPT1
Grounding points
OPT2
LEDModule status
Table 33
OPT3
FXDA interfaces
Interface
DN0951745 Issue: 25
ANT1 TX/RX
ANT2 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
PWR IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
External Alarm Connection
EAC
1
RJ45
-
© 2017 Nokia
59
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 33
FXDA interfaces (Cont.)
Interface
Label on the HW
Optical interface
OPT
Number of interfaces 3
Connector type SFP
Additional info 3 Gbps
Antenna Line Devices (ALDs) support Table 34
FXDA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V
Power per port
30 W
Functional block diagram Figure 9
FXDA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications
60
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 35
Descriptions of 3TX RF Modules
FXDA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 36
FXDA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
Table 37
100% RF Load
60
700
932
40
533
672
20
447
523
Recommended FXDA power backoff in 256 QAM mode Single carrier [dB]
0.1
Dual carrier [dB] 0.2
Installation and mechanical specifications Table 38
FXDA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation •
DN0951745 Issue: 25
© 2017 Nokia
Flexi Mounting Kit for Floor, Wall and Pole (FMFA)
61
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 38
FXDA installation and mechanical specifications (Cont.) Property
Value •
Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 39
FXDA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.)
Dimensions orientation
height
With front covers: 560 mm (22.1 in.) Width
depth
width
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 40
FXDA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 41
FXDA LEDs LED color
Red, stable
62
Description Critical alarm affecting the whole RF module or all antenna carriers
© 2017 Nokia
Alarm Fault
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 41
Descriptions of 3TX RF Modules
FXDA LEDs (Cont.) LED color
Description
Red, blinking
Operation degraded • • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm Major/critical alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
© 2017 Nokia
63
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 41
FXDA LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.5 Flexi RFM 3-pipe 1500 180 W (FRKA) FRKA technical specifications. Functional description Table 42
FRKA functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1485.9-1495.9 MHz
RX frequency range
1427.9-1437.8 MHz
DL instantaneous bandwidth
10 MHz
UL instantaneous bandwidth
10 MHz
DL filter bandwidth
10 MHz
UL filter bandwidth
10 MHz
Interfaces
64
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 10
Descriptions of 3TX RF Modules
FRKA interfaces
ANT4 RX
RXO3 ANT6 RX
RXO2
ANT5 TX/RX
DCIN
ANT2 RX
ANT3 TX/RX
Ground
ANT1 TX/RX
RXO1
OPT 1
OPT 3
OPT2 Table 43
FRKA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 44
FRKA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 28 V or 12 V ANT2, ANT4, ANT6: 12 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
65
Descriptions of 3TX RF Modules
Figure 11
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRKA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
Rx
RX filter
RXDiversity
RET
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF
RF control
OpticalIF
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
LNA
PA
TXRX
DCIN
TX filter
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 45
FRKA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
38.0 V DC to 60.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 46
FRKA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
66
100% RF Load
60
640
880
40
460
605
20
385
480
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 47
Descriptions of 3TX RF Modules
Recommended FRKA power backoff in 256 QAM mode Single carrier [dB]
0
Dual carrier [dB] 0.2
Installation and mechanical specifications Table 48
FRKA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
FRKA includes casing
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Covers for Back and Front (FMCx)
Outdoor 19'' rack •
Flexi Mounting Covers for Back and Front (FMCx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
67
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 49
FRKA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.)
Dimensions orientation
height
With front covers: 560 mm (22.1 in.) Width
depth
width
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 50
FRKA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 51
FRKA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
68
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 51
Descriptions of 3TX RF Modules
FRKA LEDs (Cont.) LED color
Description
Yellow, blinking
• •
Green, stable
•
•
Alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded RF Module fan/TX status LED: All fans are working Green RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Warnings, cautions or notes related to the product
f
g DN0951745 Issue: 25
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
69
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
7.6 Flexi RF Module 3TX 1800 (FXEA) FXEA technical specifications. Functional description Table 52
FXEA functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
A.10x version: 20 MHz A.20x version: 25 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces Figure 12
FXEA interfaces RxO3
RxO5 PWRIN
ANT6 RX
ANT5 TX/RX
EAC LED Fan/TXOff status
Grounding points LEDModule status
70
ANT4 RX
RxO1 ANT3 TX/RX
ANT1 TX/RX
ANT2 RX
OPT1 OPT2 OPT3
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 53
Descriptions of 3TX RF Modules
FXEA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
PWR IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 54
FXEA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
71
Descriptions of 3TX RF Modules
Figure 13
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXEA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
Rx
RX filter
RXDiversity
RET
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 55
FXEA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
72
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 56 Mode
Descriptions of 3TX RF Modules
FXEA power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 57
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
8+8
963
1010
1107
1/1/1 2T2R
20+20
1064
1164
1359
1/1/1 2T2R
40+40
1208
1380
1717
1/1/1 2T2R
60+60
1342
1582
2063
Recommended FXEA power backoff in 256 QAM mode Single carrier [dB]
0.2
Dual carrier [dB] 0.7
Installation and mechanical specifications Table 58
FXEA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack
DN0951745 Issue: 25
© 2017 Nokia
73
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 58
FXEA installation and mechanical specifications (Cont.) Property
Value •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 59
FXEA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.)
Dimensions orientation
height
With front covers: 560 mm (22.1 in.) Width
depth
width
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 60
FXEA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 61
FXEA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
74
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 61
Descriptions of 3TX RF Modules
FXEA LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
75
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 61
FXEA LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.7 Flexi RF Module 3TX 1900 (FXFB) FXFB technical specifications. Functional description Table 62
FXFB functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
1930-1990 MHz
RX frequency range
1850-1910 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
20 MHz
Interfaces
76
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 14
Descriptions of 3TX RF Modules
FXFB interfaces ANT3 TX/RX
ANT4 RX
ANT5
ANT6 RX
TX/RX
RXO6
RXO5
ANT2 RX RET
RXO4
ANT1 TX/RX RXO2
RXO1
RXO3
Ground
EAC
Fan/TX Status
OPT3 LED Module Status
Table 63
DCIN
OPT1
OPT2
FXFB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
PWR IN
1
Screw-terminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
6
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 64
FXFB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG: 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V
Power per port
DN0951745 Issue: 25
30 W
© 2017 Nokia
77
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Functional block diagram Figure 15
FXFB functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF
RXDiversity
RF control
OpticalIF
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
LNA
DCIN
TX filter
PA
TXRX
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 65
FXFB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 66
FXFB power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
78
100% RF Load
60
709
977
40
612
776
20
508
599
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 67
Descriptions of 3TX RF Modules
Recommended FXFB power backoff in 256 QAM mode Single carrier [dB]
0.1
Installation and mechanical specifications Table 68
FXFB installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 69
FXFB dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.)
Width
DN0951745 Issue: 25
Dimensions orientation
height width
depth
Without front covers: 447 mm (17.6 in.)
© 2017 Nokia
79
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 69
FXFB dimensions and weight (Cont.) Property
Value
Dimensions orientation
With front covers: 492 mm (19.4 in.) Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 70
FXFB environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 71
FXFB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
80
Alarm
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 71
Descriptions of 3TX RF Modules
FXFB LEDs (Cont.) LED color
Description
•
Alarm
and transmission is possible Working normally, no alarm on the RF Module
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.8 Flexi RF Module 3TX 2100 (FRGP) FRGP technical specifications. Functional description
DN0951745 Issue: 25
© 2017 Nokia
81
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 72
FRGP functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
20 MHz
Interfaces Figure 16
FRGP interfaces
ANT4 RX
RXO3 ANT6 RX
RXO2
ANT5 TX/RX
DCIN
ANT2 RX
ANT3 TX/RX
Ground
ANT1 TX/RX
RXO1
OPT 1
OPT 3
OPT2 Table 73
FRGP interfaces
Interface
82
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Optical interface
OPT
3
SFP
3 Gbps
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Antenna Line Devices (ALDs) support Table 74
FRGP ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V
Power per port
30 W
Functional block diagram Figure 17
FRGP functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RXDiversity
RF control
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 75
FRGP electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
38.0 V DC to 60.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
DN0951745 Issue: 25
© 2017 Nokia
83
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Power consumption Table 76
FRGP power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
Table 77
100% RF Load
60
557
759
40
427
553
20
317
384
Recommended FRGP power backoff in 256 QAM mode Single carrier [dB]
0.9
Dual carrier [dB] 1.4
Installation and mechanical specifications Table 78
FRGP installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
FRGP includes casing
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Floor/Wall installation • •
84
© 2017 Nokia
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Covers for Back and Front (FMCx)
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 78
Descriptions of 3TX RF Modules
FRGP installation and mechanical specifications (Cont.) Property
Value Outdoor 19'' rack •
Flexi Mounting Covers for Back and Front (FMCx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 79
FRGP dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.)
Dimensions orientation
height
With front covers: 560 mm (22.1 in.) Width
depth
width
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 80
FRGP environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 81
FRGP LEDs LED color
DN0951745 Issue: 25
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
© 2017 Nokia
85
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 81
FRGP LEDs (Cont.) LED color
Description • • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
86
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 81
Descriptions of 3TX RF Modules
FRGP LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.9 Flexi RF Module 3TX 2600 (FRHA) FRHA technical specifications. Functional description Table 82
FRHA functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2620-2690 MHz
RX frequency range
2500-2570 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
70 MHz
UL filter bandwidth
70 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
87
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 18
FRHA interfaces
ANT4 RX
RXO3 ANT6 RX
RXO2
ANT5 TX/RX
DCIN
ANT2 RX
ANT3 TX/RX
Ground
ANT1 TX/RX
RXO1
OPT 1
OPT 3
OPT2 Table 83
FRHA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 84
FRHA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 24 V
Power per port
30 W
Functional block diagram
88
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 19
Descriptions of 3TX RF Modules
FRHA functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
Rx
RX filter
RXDiversity
RET
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF
RF control
OpticalIF
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
LNA
TXRX
DCIN
TX filter
PA
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 85
FRHA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
38.0 V DC to 60.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 86
FRHA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
DN0951745 Issue: 25
100% RF Load
60
806
1130
40
622
825
20
462
580
© 2017 Nokia
89
Descriptions of 3TX RF Modules
Table 87
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FRHA power backoff in 256 QAM mode Single carrier [dB]
Dual carrier [dB]
0.9
1.4
Installation and mechanical specifications Table 88
FRHA installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Covers for Back and Front (FMCx)
Outdoor 19'' rack •
Flexi Mounting Covers for Back and Front (FMCx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 89
FRHA dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.)
90
© 2017 Nokia
Dimensions orientation
height width
depth
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 89
Descriptions of 3TX RF Modules
FRHA dimensions and weight (Cont.) Property
Value
Width
Dimensions orientation
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 90
FRHA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 91
FRHA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
© 2017 Nokia
91
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 91
FRHA LEDs (Cont.) LED color
Description
Green, stable
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
Alarm No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.10 Flexi RF Module 3TX 1700/2100 (FRIE) FRIE technical specifications.
92
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Functional description Table 92
FRIE functional specification Property
Value
Output power
3x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1710-1770 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
45 MHz
UL filter bandwidth
45 MHz
Interfaces Figure 20
FRIE interfaces
ANT4 RX
RXO3 ANT6 RX
ANT5 TX/RX
DCIN
ANT2 RX
RXO2 ANT3 TX/RX
Ground
ANT1 TX/RX
RXO1
OPT 1
OPT 3
OPT2 Table 93
FRIE interfaces
Interface
DN0951745 Issue: 25
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
2-pin multibeam XL
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
© 2017 Nokia
93
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 93
FRIE interfaces (Cont.)
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps
Antenna Line Devices (ALDs) support Table 94
FRIE ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V
Power per port
30 W
Functional block diagram Figure 21
FRIE functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications
94
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 95
Descriptions of 3TX RF Modules
FRIE electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 96
FRIE power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
Table 97
100% RF Load
60
590
805
40
465
610
20
345
420
Recommended FRIE power backoff in 256 QAM mode Single carrier [dB]
0.9
Dual carrier [dB] 1.4
Installation and mechanical specifications Table 98
FRIE installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
FRIE includes casing
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
•
Pole installation •
DN0951745 Issue: 25
© 2017 Nokia
Flexi Mounting Kit for Floor, Wall and Pole (FMFA)
95
Descriptions of 3TX RF Modules
Table 98
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRIE installation and mechanical specifications (Cont.) Property
Value •
Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Mounting Covers for Back and Front (FMCx)
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Mounting Covers for Back and Front (FMCx)
Outdoor 19'' rack •
Flexi Mounting Covers for Back and Front (FMCx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 99
FRIE dimensions and weight Property
Value
Height
133 mm/ 3U (5.2 in.)
Depth
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.)
Width
Dimensions orientation
height width
depth
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
25 l
Environmental specifications Table 100
FRIE environmental specifications Property
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
96
© 2017 Nokia
Value +55°C (131°F)
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 100
Descriptions of 3TX RF Modules
FRIE environmental specifications (Cont.) Property
Value
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 101
FRIE LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded due to external factors (for example, VSWR minor/major
Alarm
© 2017 Nokia
97
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 101
FRIE LEDs (Cont.) LED color
Description
Alarm
values exceeded, Antenna line device faulty/degraded) Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.11 Flexi RF Module 3TX 850 (FXCB) FXCB technical specifications. Functional description Table 102
FXCB functional specification Property
98
Value
Output power
3x80 W
MIMO
No
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
869-894 MHz
RX frequency range
824-849 MHz
DL instantaneous bandwidth
25 MHz
UL instantaneous bandwidth
25 MHz
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 102
Descriptions of 3TX RF Modules
FXCB functional specification (Cont.) Property
Value
DL filter bandwidth
25 MHz
UL filter bandwidth
25 MHz
Interfaces Figure 22
FXCB interfaces ANT5
ANT6 RX
TX/RX
RXO6
ANT3 TX/RX
ANT4 RX RXO5
ANT2 RX RET
RXO4
ANT1 TX/RX RXO2
RXO1
RXO3
Ground
EAC
Fan/TX Status
OPT3 LED Module Status
Table 103
DCIN
OPT1
OPT2
FXCB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
6
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support
DN0951745 Issue: 25
© 2017 Nokia
99
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 104
FXCB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V
Power per port
30 W
Functional block diagram Figure 23
FXCB functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
RXDiversity
RET
FXDB,FXEB, FXFB
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
PA
TXRX
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 105
FXCB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
100
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Power consumption Table 106 Mode
FXCB power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
460
460
460
460
460
460
2/2/2
20
474
492
580
470
474
478
4/4/4
20
606
699
872
517
543
572
WCDMA 1/1/1
20
330
372
455
2/2/2
20
393
460
600
3/3/3
20
503
604
820
4/4/4
20
559
684
947
1/1/1 2T2R
20+20
656
750
916
1/1/1 2T2R
40+40
778
929
1211
1/1/1 2T2R
60+60
957
1176
1598
1/1/1 2T2R
80+80
1058
1330
1848
GSM 2/2/2
20
638
697
829
LTE
MSR
20
WCDMA 1/1/1
Table 107
Recommended FXCB power backoff in 256 QAM mode Single carrier [dB]
0.8
Dual carrier [dB] 1.1
Installation and mechanical specifications
DN0951745 Issue: 25
© 2017 Nokia
101
Descriptions of 3TX RF Modules
Table 108
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXCB installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 109
FXCB dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
102
Weight
25 kg (55.1 lb)
Volume
19.3 l
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Environmental specifications Table 110
FXCB environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 111
FXCB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
103
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 111
FXCB LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.12 Flexi RF Module 3TX 900 (FXDB) FXDB technical specifications. Functional description Table 112
FXDB functional specification Property
104
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 112
Descriptions of 3TX RF Modules
FXDB functional specification (Cont.) Property
Value
TX frequency range
925-960 MHz
RX frequency range
880-915 MHz
DL instantaneous bandwidth
35 MHz
UL instantaneous bandwidth
35 MHz
DL filter bandwidth
35 MHz
UL filter bandwidth
35 MHz
Interfaces Figure 24
FXDB interfaces ANT5 TX/RX
RXO5
ANT3 TX/RX ANT4 RX RXO3
ANT6 RX
Ground
EAC
RET
Fan/TX Status
OPT3 LED Module Status
Table 113
ANT2 RX
ANT1 TX/RX RXO1
DCIN
OPT1
OPT2
FXDB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support
DN0951745 Issue: 25
© 2017 Nokia
105
Descriptions of 3TX RF Modules
Table 114
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXDB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5. RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V
Power per port
30 W
Functional block diagram Figure 25
FXDB functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
RXDiversity
RET
FXDB,FXEB, FXFB
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
PA
TXRX
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 115
FXDB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
106
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Power consumption Table 116 Mode
FXDB power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
460
460
460
460
460
460
2/2/2
20
473
492
586
480
485
490
4/4/4
20
629
731
930
534
561
592
WCDMA 1/1/1
20
331
372
453
2/2/2
20
393
460
606
3/3/3
20
486
588
813
4/4/4
20
543
671
952
1/1/1 2T2R
20+20
665
753
916
1/1/1 2T2R
40+40
787
932
1223
1/1/1 2T2R
60+60
983
1209
1661
1/1/1 2T2R
80+80
1098
1381
1939
GSM 2/2/2
20
584
637
827
LTE
MSR
20
WCDMA 1/1/1
Table 117
Recommended FXDB power backoff in 256 QAM mode Single carrier [dB]
1.2
Dual carrier [dB] 1.3
Installation and mechanical specifications
DN0951745 Issue: 25
© 2017 Nokia
107
Descriptions of 3TX RF Modules
Table 118
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXDB installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 119
FXDB dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
108
Weight
25 kg (55.1 lb)
Volume
19.3 l
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Environmental specifications Table 120
FXDB environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 121
FXDB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
109
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 121
FXDB LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: All fans are faulty Red
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.13 Flexi RF Module 3TX 1800 (FXEB) FXEB technical specifications. Functional description Table 122
FXEB functional specification Property
110
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, FDD-LTE
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 122
Descriptions of 3TX RF Modules
FXEB functional specification (Cont.) Property
Value
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
35 MHz in GSM 50 MHz in LTE
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces Figure 26
FXEB interfaces ANT5 TX/RX
RXO5
ANT3 TX/RX ANT4 RX RXO3
ANT6 RX
Ground
EAC
ANT1 TX/RX RXO1
DCIN
OPT1
OPT2
FXEB interfaces
Interface
DN0951745 Issue: 25
RET
Fan/TX Status
OPT3 LED Module Status
Table 123
ANT2 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
© 2017 Nokia
111
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Antenna Line Devices (ALDs) support Table 124
FXEB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V
Power per port
30 W
Functional block diagram Figure 27
FXEB functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
Rx
RX filter
RXDiversity
RET
FXDB,FXEB, FXFB
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 125
FXEB electrical specifications Property
112
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 125
Descriptions of 3TX RF Modules
FXEB electrical specifications (Cont.) Property
Value -57.0 V DC to -60.0 V DC
Power consumption Table 126 Mode
FXEB power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
LTE
MSR
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
438
438
438
438
438
438
2/2/2
20
454
481
601
452
457
463
4/4/4
20
596
709
957
491
520
554
8/8/8
20
998
1387
1869
1/1/1 2T2R
20+20
657
728
891
1/1/1 2T2R
40+40
770
907
1226
1/1/1 2T2R
60+60
915
1118
1589
1/1/1 2T2R
80+80
1022
1284
1900
GSM 2/2/2
20
836
937
1206
1002
1198
1592
20+20
LTE 1/1/1 2T2R GSM 4/4/4
20 20+20
LTE 1/1/1 2T2R
DN0951745 Issue: 25
© 2017 Nokia
113
Descriptions of 3TX RF Modules
Table 127
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FXEB power backoff in 256 QAM mode Single carrier [dB]
Dual carrier [dB]
0.8
1.4
Installation and mechanical specifications Table 128
FXEB installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 129
FXEB dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
114
height width
depth
Core RFM: 420 mm (16.5 in.)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 129
Descriptions of 3TX RF Modules
FXEB dimensions and weight (Cont.) Property
Value
Dimensions orientation
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications Table 130
FXEB environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 131
FXEB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
© 2017 Nokia
115
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 131
FXEB LEDs (Cont.) LED color
Description
Green, stable
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
Alarm No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.14 Flexi RFM 3-pipe 1800 240 W (FXEE) FXEE technical specifications.
116
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Functional description Table 132
FXEE functional specification Property
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
GSM, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
75 MHz in LTE, LTE/GSM Sharing
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces Figure 28
FXEE interfaces
RXO3 ANT6 RX
EAC OPT1 LED Module Status
Ground
Table 133
ANT3 TX/RX
ANT1 TX/RX
ANT2 RX
RET
RXO1
DCIN OPT3
Fan/RF Status OPT2
FXEE interfaces
Interface
DN0951745 Issue: 25
ANT 5 TX/RX RXO2 ANT4 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
© 2017 Nokia
117
Descriptions of 3TX RF Modules
Table 133
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXEE interfaces (Cont.)
Interface
Label on the HW
RF output connector
Number of interfaces
Connector type
Additional info
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps to 6 Gbps
Antenna Line Devices (ALDs) support Table 134
FXEE ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 25 V
Power per port
30 W
Functional block diagram
118
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 29
Descriptions of 3TX RF Modules
FXEE functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
Rx
RX filter
RXDiversity
RET
FXDB,FXEB, FXFB
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 135
FXEE electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
119
Descriptions of 3TX RF Modules
Table 136 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXEE power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
LTE
MSR
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
492
492
492
492
492
492
2/2/2
20
520
545
633
518
523
528
4/4/4
20
674
766
962
583
609
639
1/1/1 2T2R
20+20
701
774
936
1/1/1 2T2R
40+40
815
957
1246
1/1/1 2T2R
60+60
960
1149
1559
1/1/1 2T2R
80+80
1108
1346
1886
GSM 2/2/2
20
1007
1113
1322
1139
1302
1651
1300
1523
2001
20+20
LTE 1/1/1 2T2R 10 MHz GSM 4/4/4
20 20+20
LTE 1/1/1 2T2R 10 MHz GSM 4/4/4
20 40+40
LTE 1/1/1 2T2R 10 MHz
RF power backoff
120
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 137
Descriptions of 3TX RF Modules
Recommended FXEE power backoff in 256 QAM mode Single carrier [dB]
Dual carrier [dB]
0.4
0.8
Installation and mechanical specifications Table 138
FXEE installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 139
FXEE dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
DN0951745 Issue: 25
height width
depth
Core RFM: 420 mm (16.5 in.)
© 2017 Nokia
121
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 139
FXEE dimensions and weight (Cont.) Property
Value
Dimensions orientation
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications Table 140
FXEE environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 141
FXEE LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
122
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 141
Descriptions of 3TX RF Modules
FXEE LEDs (Cont.) LED color
Description
Green, stable
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
Alarm No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded RF Module fan/TX status LED: All fans are working Green RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.15 Flexi RFM 3-pipe 1800 240 W (FXEF) FXEF technical specifications.
DN0951745 Issue: 25
© 2017 Nokia
123
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Functional description Table 142
FXEF functional specification Property
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
GSM, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
75 MHz
UL instantaneous bandwidth
75 MHz in LTE, LTE/GSM Sharing
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces Figure 30
FXEF interfaces
RXO3 ANT6 RX
GND
Table 143
EAC OPT1 LED Module Status
ANT3 TX/RX
ANT1 TX/RX
ANT2 RX
RET
RXO1
OPT3
DCIN Fan/RF Status
MoistureVent
OPT2
FXEF interfaces
Interface
124
ANT 5 TX/RX RXO2 ANT4 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 143
Descriptions of 3TX RF Modules
FXEF interfaces (Cont.)
Interface
Label on the HW
RF output connector
Number of interfaces
Connector type
Additional info
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps to 6 Gbps
1
M8 or dual M5 screws
Ground Moisture Vent
Moisture Vent
1
Antenna Line Devices (ALDs) support Table 144
FXEF ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
125
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 31
FXEF functional block diagram Duplexfilter+DiversityRX
RFModule
TX
TX filter
PA
Bias-T
LNA
EAC
RXOUT Bias-T
LNA
LNA
OpticalIF OpticalIF
RF control
RX
RX filter
RXDiversity
RET
Bias-T
RXDiversity
RX filter
RXMain
RX filter
RX
RXOUT Bias-T
Det
TX filter
OpticalIF LNA
VSWR TX/RXRF
LNA
PA
TX
TX/RXRF
Det
RX filter
RXMain
VSWR
Bias-T
RXDiversity
RX filter
RXMain
RX filter
RX
RXOUT
LNA
TX
TX filter
PA
DCIN
Bias-T
VSWR TX/RXRF Det
PSU Fanassembly
Electrical specifications Table 145
FXEF electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
126
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 146 Mode
Descriptions of 3TX RF Modules
FXEF power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
LTE
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
451
451
451
451
451
451
2/2/2
20
457
469
550
455
458
461
4/4/4
20
638
728
925
549
574
602
1/1/1 2T2R
20+20
579
649
789
1/1/1 2T2R
40+40
733
812
1089
1/1/1 2T2R
60+60
838
1018
1435
1/1/1 2T2R
80+80
1003
1244
1808
Installation and mechanical specifications Table 147
FXEF installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation
DN0951745 Issue: 25
© 2017 Nokia
127
Descriptions of 3TX RF Modules
Table 147
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXEF installation and mechanical specifications (Cont.) Property
Value • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 148
FXEF dimensions and weight Property
Value
Height
Core RFM: 118 mm (4.6 in.)
Depth
Core RFM: 404 mm (15.9 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 441 mm (17.4 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications Table 149
FXEF environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs
128
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 150
Descriptions of 3TX RF Modules
FXEF LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
DN0951745 Issue: 25
Alarm
© 2017 Nokia
No alarm
-
129
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 150
FXEF LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.16 Flexi RF Module 3TX 1900 (FXFC) FXFC technical specifications. Functional description Table 151
FXFC functional specification Property
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
1930-1990 MHz
RX frequency range
1850-1910 MHz
DL instantaneous bandwidth
35 MHz in GSM and WCDMA 50 MHz in LTE
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces
130
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 32
Descriptions of 3TX RF Modules
FXFC interfaces ANT5
ANT6 RX
TX/RX
RXO6
ANT3 TX/RX
ANT4 RX RXO5
ANT2 RX RET
RXO4
ANT1 TX/RX RXO2
RXO1
RXO3
Ground
EAC
Fan/TX Status
OPT3 LED Module Status
Table 152
DCIN
OPT1
OPT2
FXFC interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
6
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 153
FXFC ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V
Power per port
DN0951745 Issue: 25
30 W
© 2017 Nokia
131
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Functional block diagram Figure 33
FXFC functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
RXDiversity
RET
FXDB,FXEB, FXFB
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RXDiversity
RF control
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 154
FXFC electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
132
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 155 Mode
Descriptions of 3TX RF Modules
FXFC power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
483
483
483
483
483
483
2/2/2
20
498
527
653
496
502
508
4/4/4
20
674
799
1060
557
590
628
WCDMA 1/1/1
20
318
353
428
2/2/2
20
377
439
587
3/3/3
20
465
554
778
4/4/4
20
515
641
923
1/1/1 2T2R
20+20
736
820
988
1/1/1 2T2R
40+40
857
1008
1342
1/1/1 2T2R
60+60
1018
1242
1744
1/1/1 2T2R
80+80
1139
1434
2080
LTE
Table 156
Recommended FXFC power backoff in 256 QAM mode Single carrier [dB]
0.8
Dual carrier [dB] 1.4
Installation and mechanical specifications Table 157
FXFC installation and mechanical specifications Property
Installation options
IP rating
DN0951745 Issue: 25
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP65
© 2017 Nokia
133
Descriptions of 3TX RF Modules
Table 157
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXFC installation and mechanical specifications (Cont.) Property
Value
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 158
FXFC dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications
134
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 159
Descriptions of 3TX RF Modules
FXFC environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 160
FXFC LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
135
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 160
FXFC LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.17 Flexi RF Module 3TX 2100 (FRGT) FRGT technical specifications. Functional description Table 161
FRGT functional specification Property
136
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 161
Descriptions of 3TX RF Modules
FRGT functional specification (Cont.) Property
Value
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Table 162
FRGT output power in RU40 release and onwards DL bandwidth
Output power
0-20 MHz
80 W
20-45 MHz
70 W (BTS can be commissioned as 80 W (for example 4x20 W per pipe) and RFM internal power control limits the total power to 70 W when needed.)
45-60 MHz
60 W
Interfaces Figure 34
FRGT interfaces ANT5 TX/RX
RXO5
ANT3 TX/RX ANT4 RX RXO3
ANT6 RX
Ground
EAC
ANT1 TX/RX RXO1
DCIN
OPT1
OPT2
FRGT interfaces
Interface
DN0951745 Issue: 25
RET
Fan/TX Status
OPT3 LED Module Status
Table 163
ANT2 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
© 2017 Nokia
137
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 163
FRGT interfaces (Cont.)
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 164
FRGT ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 24 V
Power per port
30 W
Functional block diagram Figure 35
FRGT functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA FXDB,FXEB, FXFB
RXDiversity
RET
Rx
RX filter
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF OpticalIF
RF control
RXDiversity
Rx RxOUT
RX filter
RXMain
Bias-T
Det
TX filter
PA
TXRX OpticalIF**
LNA
VSWR Tx/Rx
LNA
FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT
LNA
TXRX
DCIN
PA
TX filter
Bias-T
VSWR Tx/Rx Det
PSU Fanassembly
138
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Electrical specifications Table 165
FRGT electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 166 Mode
FRGT power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
MSR
ETSI 202706 busy hour load PBH RRH, static
20
287
316
386
2/2/2
20
356
414
547
3/3/3
20
437
522
729
4/4/4
20
494
608
885
1/1/1 2T2R
20+20
580
651
796
1/1/1 2T2R
40+40
711
843
1117
1/1/1 2T2R
60+60
818
1010
1427
1/1/1 2T2R
80+80
976
1232
1803
719
847
1126
926
1141
1661
WCDMA 2/2/2 20 20+20
WCDMA 2/2/2 20 LTE 1/1/1 2T2R 10MHz
40+40
Recommended FRGT power backoff in 256 QAM mode Single carrier [dB]
0.8
DN0951745 Issue: 25
100% RF power load P100% RRH
1/1/1
LTE 1/1/1 2T2R 10MHz
Table 167
ETSI 202706 average load PRRH, static
Power consumption
Dual carrier [dB] 0.8
© 2017 Nokia
139
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Installation and mechanical specifications Table 168
FRGT installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 169
FRGT dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
140
25 kg (55.1 lb)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 169
Descriptions of 3TX RF Modules
FRGT dimensions and weight (Cont.) Property
Value
Volume
Dimensions orientation
19.3 l
Environmental specifications Table 170
FRGT environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 171
FRGT LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
© 2017 Nokia
No alarm
141
Descriptions of 3TX RF Modules
Table 171
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGT LEDs (Cont.) LED color
Description
Alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.18 Flexi RF Module 3TX 2100 (FRGS) FRGS technical specifications. Functional description
142
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 172
Descriptions of 3TX RF Modules
FRGS functional specification Property
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
2130-2170 MHz
RX frequency range
1940-1980 MHz
DL instantaneous bandwidth
40 MHz
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
40 MHz
UL filter bandwidth
40 MHz
Table 173
FRGS output power in RU40 DL bandwidth
Output power
0-20 MHz
80 W
20-40 MHz
70 W (BTS can be commissioned as 80 W (for example 4x20 W per pipe) and RFM internal power control limits the total power to 70 W when needed.)
Interfaces Figure 36
FRGS interfaces ANT5 TX/RX
RXO5
ANT4 RX RXO3
ANT6 RX
Ground
ANT3 TX/RX
EAC
OPT3 LED Module Status
DN0951745 Issue: 25
© 2017 Nokia
ANT2 RX RET
Fan/TX Status
ANT1 TX/RX RXO1
DCIN
OPT1
OPT2
143
Descriptions of 3TX RF Modules
Table 174
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGS interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 175
FRGS ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 24 V
Power per port
30 W
Functional block diagram
144
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 37
Descriptions of 3TX RF Modules
FRGS functional block diagram Duplexfilter+DiversityRX
RFModule
TXRX
TX filter
PA
Bias-T
LNA
Tx/Rx
Det
RX filter
RXMain
VSWR
RxOUT Bias-T
LNA
Rx
RX filter
RXDiversity
RET
FXDB,FXEB, FXFB
RxOUT*FXCx,FXFx
RFLoop LNA
OpticalIF
RF control
OpticalIF
RXDiversity RXMain
RX filter
Rx RxOUT Bias-T
Det
TX filter
OpticalIF** LNA
VSWR Tx/Rx
LNA
PA
TXRX FRGP,FRIE, FXDA,FXCA, FXEA,FRKA
RxOUT*FXCx,FXFx
Bias-T RX filter
RxOUT*FXCx,FXFx
Bias-T
RXDiversity
RX filter
RXMain
RX filter
Rx RxOUT Bias-T
LNA
TXRX
DCIN
TX filter
PA
VSWR Tx/Rx Det
PSU Fanassembly
Electrical specifications Table 176
FRGS electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 177
FRGS power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
3
DN0951745 Issue: 25
100% RF Load
80
595
892
60
524
738
40
405
541
20
314
381
© 2017 Nokia
145
Descriptions of 3TX RF Modules
Table 178
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FRGS power backoff in 256 QAM mode Single carrier [dB]
Dual carrier [dB]
0.9
0.8
Installation and mechanical specifications Table 179
FRGS installation and mechanical specifications Property
Value
Installation options
•
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 180
FRGS dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
146
height width
depth
Core RFM: 420 mm (16.5 in.)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 180
Descriptions of 3TX RF Modules
FRGS dimensions and weight (Cont.) Property
Value
Dimensions orientation
Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications Table 181
FRGS environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 182
FRGS LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
© 2017 Nokia
147
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 182
FRGS LEDs (Cont.) LED color
Description
Green, stable
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
Alarm No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
7.19 Flexi RFM 3-pipe 2100 240 W (FRGX) FRGX technical specifications.
148
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 3TX RF Modules
Functional description Table 183
FRGX functional specification Property
Value
Output power
3x80 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces Figure 38
FRGX interfaces
RXO3 ANT6 RX
GND
Table 184
EAC OPT1 LED Module Status
ANT3 TX/RX
ANT1 TX/RX
ANT2 RX
RET
RXO1
OPT3
DCIN Fan/RF Status
MoistureVent
OPT2
FRGX interfaces
Interface
DN0951745 Issue: 25
ANT 5 TX/RX RXO2 ANT4 RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
© 2017 Nokia
149
Descriptions of 3TX RF Modules
Table 184
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGX interfaces (Cont.)
Interface
Label on the HW
RF output connector
Number of interfaces
Connector type
Additional info
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps to 6 Gbps
1
M8 or dual M5 screws
-
1
Core Vent
-
Ground Moisture Vent
-
Antenna Line Devices (ALDs) support Table 185
FRGX ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 25 V
Power per port
30 W
Functional block diagram
150
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 39
Descriptions of 3TX RF Modules
FRGX functional block diagram Duplexfilter+DiversityRX
RFModule
TX
TX filter
PA
Bias-T
LNA
EAC
RXOUT Bias-T
LNA
LNA
OpticalIF OpticalIF
RF control
RX
RX filter
RXDiversity
RET
Bias-T
RXDiversity
RX filter
RXMain
RX filter
RX
RXOUT Bias-T
Det
TX filter
OpticalIF LNA
VSWR TX/RXRF
LNA
PA
TX
TX/RXRF
Det
RX filter
RXMain
VSWR
Bias-T
RXDiversity
RX filter
RXMain
RX filter
RX
RXOUT
LNA
TX
TX filter
PA
DCIN
Bias-T
VSWR TX/RXRF Det
PSU Fanassembly
Electrical specifications Table 186
FRGX electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
g
DN0951745 Issue: 25
Note: FRGX power consumption values are preliminary, and will be confirmed in further releases.
© 2017 Nokia
151
Descriptions of 3TX RF Modules
Table 187 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGX power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
MSR
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1
20
287
316
386
2/2/2
20
356
414
547
3/3/3
20
437
522
729
4/4/4
20
494
608
885
1/1/1 2T2R
20+20
580
651
796
1/1/1 2T2R
40+40
711
843
1117
1/1/1 2T2R
60+60
818
1010
1427
1/1/1 2T2R
80+80
976
1232
1803
719
847
1126
926
1141
1661
WCDMA 2/2/2 20 LTE 1/1/1 2T2R 10 MHz
20+20
WCDMA 2/2/2 40 LTE 1/1/1 2T2R 10 MHz
40+40
Installation and mechanical specifications Table 188
FRGX installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
152
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 188
Descriptions of 3TX RF Modules
FRGX installation and mechanical specifications (Cont.) Property
Value •
Flexi Module Casing (EMHx)
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 189
FRGX dimensions and weight Property
Value
Height
Core RFM: 118 mm (4.6 in.)
Depth
Core RFM: 404 mm (15.9 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 441 mm (17.4 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
25 kg (55.1 lb)
Volume
19.3 l
Environmental specifications Table 190
FRGX environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
© 2017 Nokia
153
Descriptions of 3TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
LEDs Table 191
FRGX LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
154
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 191
Descriptions of 3TX RF Modules
FRGX LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: All fans are working Green RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
f
g
DN0951745 Issue: 25
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The maximum startup voltage is -40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
155
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
8 Descriptions of 6TX RF Modules 8.1 Flexi RF Module 6TX 700 (FRPA) FRPA technical specifications. Functional description Table 192
FRPA functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
758-793 MHz
RX frequency range
703-738 MHz
DL instantaneous bandwidth
35 MHz
g UL instantaneous bandwidth
Note: In FL15A and FL16 the DL instantaneous bandwidth is 30 MHz.
35 MHz
g
Note: In FL15A and FL16 the UL instantaneous bandwidth is 30 MHz.
DL filter bandwidth
35 MHz
UL filter bandwidth
35 MHz
Interfaces
156
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 40
ANT6 TX/RX
FRPA interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 193
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRPA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 194
FRPA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
157
Descriptions of 6TX RF Modules
Figure 41
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRPA functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 195
FRPA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
158
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 196 Mode
Descriptions of 6TX RF Modules
FRPA power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 197
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
399
453
568
1/1/1 2T2R
40+40
576
692
934
Recommended FRPA power backoff in 256 QAM mode Single carrier [dB]
0.6
Dual carrier [dB] 1.2
Installation and mechanical specifications Table 198
FRPA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
159
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 198
FRPA installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 199
FRPA dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 200
FRPA environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 201
FRPA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
160
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 201
Descriptions of 6TX RF Modules
FRPA LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
161
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 201
FRPA LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.2 Flexi RF Module 6TX 700 (FRPB) FRPB technical specifications. Functional description Table 202
FRPB functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
773-803 MHz
RX frequency range
718-748 MHz
DL instantaneous bandwidth
30 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces
162
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 42
ANT6 TX/RX
FRPB interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 203
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRPB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 204
FRPB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
163
Descriptions of 6TX RF Modules
Figure 43
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRPB functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 205
FRPB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
164
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 206 Mode
Descriptions of 6TX RF Modules
FRPB power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 207
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
399
453
568
1/1/1 2T2R
40+40
576
692
934
Recommended FRPB power backoff in 256 QAM mode Single carrier [dB]
0.6
Dual carrier [dB] 1.2
Installation and mechanical specifications Table 208
FRBP installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
165
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 208
FRBP installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 209
FRPB dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 210
FRPB environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 211
FRPB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
166
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 211
Descriptions of 6TX RF Modules
FRPB LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
167
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 211
FRPB LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.3 Flexi RFM 6-pipe 700 240 W (FRPD) FRPD technical specifications.
g
Note: This HW variant supports Fast Delivery Mode on top of FL16 release. Functional description Table 212
FRPD functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
758-788 MHz
RX frequency range
703-733 MHz
DL instantaneous bandwidth
30 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces
168
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 44
ANT6 TX/RX
FRPD interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 213
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRPD interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power Connector DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
RS-485
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
1.5 Gbps to 6 Gbps, OBSAI
Antenna Line Devices (ALDs) support Table 214
FRPD ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 24 V RET: 24 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
169
Descriptions of 6TX RF Modules
Figure 45
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRPD functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 215
FRPD electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
170
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 216 Mode
Descriptions of 6TX RF Modules
FRPD power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 6h busy hour load) / 24h Power Power consumption consumption
LTE
Table 217
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
419
476
591
1/1/1 2T2R
40+40
610
735
981
Recommended FRPD power backoff in 256 QAM mode Single carrier [dB]
0.6
Dual carrier [dB] 1.2
Installation and mechanical specifications Table 218
FRPD installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
171
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 218
FRPD installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 219
FRPD dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 220
FRPD environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 221
FRPD LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
172
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 221
Descriptions of 6TX RF Modules
FRPD LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded RF Module fan/TX status LED: All fans are working Green RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
DN0951745 Issue: 25
© 2017 Nokia
173
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 221
FRPD LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.4 Flexi RF Module 6TX 2600 (FRHC) FRHC technical specifications. Functional description Table 222
FRHC functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2620-2675 MHz
RX frequency range
2500-2555 MHz
DL instantaneous bandwidth
40 MHz
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
55 MHz
UL filter bandwidth
55 MHz
Interfaces
174
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 46
ANT6 TX/RX
FRHC interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 223
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRHC interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 224
FRHC ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
175
Descriptions of 6TX RF Modules
Figure 47
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRHC functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 225
FRHC electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
176
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 226 Mode
Descriptions of 6TX RF Modules
FRHC power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 227
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
470
553
740
1/1/1 2T2R
40+40
657
800
1131
Recommended FRHC power backoff in 256 QAM mode Single carrier [dB]
1.0
Dual carrier [dB] 1.4
Installation and mechanical specifications Table 228
FRHC installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
177
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 228
FRHC installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 229
FRHC dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 230
FRHC environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 231
FRHC LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
178
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 231
Descriptions of 6TX RF Modules
FRHC LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
179
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 231
FRHC LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.5 Flexi RF Module 6TX 2600 (FRHF) FRHF technical specifications. Functional description Table 232
FRHF functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2640-2690 MHz
RX frequency range
2520-2570 MHz
DL instantaneous bandwidth
40 MHz
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
50 MHz
UL filter bandwidth
50 MHz
Interfaces
180
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 48
ANT6 TX/RX
FRHF interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 233
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRHF interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 234
FRHF ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
181
Descriptions of 6TX RF Modules
Figure 49
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRHF functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 235
FRHF electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
182
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 236 Mode
Descriptions of 6TX RF Modules
FRHF power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 237
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
476
566
769
1/1/1 2T2R
40+40
641
790
1142
Recommended FRHF power backoff in 256 QAM mode Single carrier [dB]
0.7
Dual carrier [dB] 1.4
Installation and mechanical specifications Table 238
FRHF installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
183
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 238
FRHF installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 239
FRHF dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 240
FRHF environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 241
FRHF LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
184
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 241
Descriptions of 6TX RF Modules
FRHF LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
185
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 241
FRHF LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.6 Flexi RF Module 6TX 800 (FRMC) FRMC technical specifications. Functional description Table 242
FRMC functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
801-821 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
30 MHz
Interfaces
186
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 50
ANT6 TX/RX
FRMC interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 243
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRMC interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw-interminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 244
FRMC ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
187
Descriptions of 6TX RF Modules
Figure 51
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRMC functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 245
FRMC electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
188
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 246 Mode
Descriptions of 6TX RF Modules
FRMC power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 247
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
418
479
616
1/1/1 2T2R
40+40
591
714
987
Recommended FRMC power backoff in 256 QAM mode Single carrier [dB]
0.7
Installation and mechanical specifications Table 248
FRMC installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
189
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 248
FRMC installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 249
FRMC dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 250
FRMC environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 251
FRMC LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
•
190
Alarm
Major alarm affecting the whole RF Module
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 251
Descriptions of 6TX RF Modules
FRMC LEDs (Cont.) LED color
Description • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: All fans are faulty Red
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
191
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 251
FRMC LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.7 Flexi RFM 6-pipe 800 240 W (FRME) FRME technical specifications. Functional description Table 252
FRME functional specification Property
Value
Output power
6x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
791-811 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
30 MHz
Interfaces
192
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 52
ANT6 TX/RX
FRME interfaces
ANT5 TX/RX
Ground EAC/LMP
Table 253
Descriptions of 6TX RF Modules
ANT4 TX/RX
OPT1 LED Module Status
ANT3 TX/RX
RET
ANT2 TX/RX
ANT1 TX/RX
Fan/RF Status OPT2
OPT3
FRME interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
Screw terminal
-
Antenna connector
ANT
6
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
1.5 Gbps to 6 Gbps, OBSAI
Antenna Line Devices (ALDs) support Table 254
FRME ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V RET: 25 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
193
Descriptions of 6TX RF Modules
Figure 53
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRME functional block diagram
RFModule
Filter
PA TXRF
TX filter
PA Main PA Div
EAC
RXRF LNA
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
RET
PA
TXRF RXRF
RF control
LNA
Tx/Rx Det
RX filter
TX filter
PA Main PA Div
Optical IF Optical IF
LNA
VSWR
Bias-T
VSWR Tx/Rx Det
RX filter
RXMain
TX filter
RXDiv
Optical IF** LNA
VSWR Tx/Rx Det
RX filter
PA TXRF
TX filter
PA Main PA Div
RXRF LNA
RXMain
Bias-T
RX filter TX filter
RXDiv
LNA
DCIN
RX filter
VSWR Tx/Rx Det
VSWR Tx/Rx Det
PSU
Fanassembly
Electrical specifications Table 255
FRME electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
194
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 256 Mode
Descriptions of 6TX RF Modules
FRME power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 257
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
409
467
605
1/1/1 2T2R
40+40
596
722
997
Recommended FRME power backoff in 256 QAM mode Single carrier [dB]
0.7
Dual carrier [dB] 0.9
Installation and mechanical specifications Table 258
FRME installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack
DN0951745 Issue: 25
© 2017 Nokia
195
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 258
FRME installation and mechanical specifications (Cont.) Property
Value •
No optional items needed
Dimensions and weight Table 259
FRME dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.)
height
Width
depth
width
With front covers: 560 mm (22.1 in.) Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 260
FRME environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 261
FRME LEDs LED color
196
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 261
Descriptions of 6TX RF Modules
FRME LEDs (Cont.) LED color
Description • • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: All fans are faulty Red
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
© 2017 Nokia
197
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 261
FRME LEDs (Cont.) LED color
Description
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Alarm -
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.8 Flexi RFM 6-pipe 800 360 W (FRMF) FRMF technical specifications. Functional description Table 262
FRMF functional specification Property
Value
Output power
6x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
791-821 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
30 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces
198
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 54
FRMF interfaces
RXO3 ANT6 TX/RX
ANT 5 TX/RX RXO2 ANT4 TX/RX
EAC OPT1 LED Module Status
Ground
Table 263
Descriptions of 6TX RF Modules
ANT3 TX/RX
ANT1 TX/RX
ANT2 TX/RX
RET
RXO1
DCIN OPT3
Fan/RF Status OPT2
FRMF interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support Table 264
FRMF ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3, ANT5: 25 V
© 2017 Nokia
199
Descriptions of 6TX RF Modules
Table 264
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRMF ALD support (Cont.)
ALD support via antenna ports
Value RET: 25 V
Power per port
30 W
Functional block diagram Figure 55
FRMF functional block diagram RFModule
Filter PA TXRF
TX filter
PA Main
Bias-T
PA Div
EAC LNA
RXRF RET
RXDiv
PA TXRF
LNA
Bias-T
OpticalIF
LNA
RXRF
RF
control
Bias-T
RXDiv
OpticalIF PA TXRF
LNA
Bias-T
LNA
Bias-T
RXDiv
LNA
DCIN
Tx/Rx
VSWR Det
RX filter
Tx/Rx
RxOUT TX filter
RXMain
VSWR Det
RX filter
PA Div
RXRF
Tx/Rx
RxOUT
TX filter
PA Main
Tx/Rx
VSWR Det
RX filter TX filter
RXMain
VSWR Det
RX filter
PA Div
OpticalIF
Tx/Rx
RxOUT
TX filter
PA Main
Det
RX filter TX filter
RXMain
VSWR
RX filter
Bias-T
VSWR Det
Tx/Rx
PSU
Fanassembly
Electrical specifications Table 265
FRMF electrical specifications Property
200
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 265
Descriptions of 6TX RF Modules
FRMF electrical specifications (Cont.) Property
Value -57.0 V DC to -60.0 V DC
Power consumption Table 266 Mode
FRMF power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 267
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
466
533
665
1/1/1 2T2R
40+40
606
733
985
1/1/1 2T2R
60+60
755
942
1326
Recommended FRMF power backoff in 256 QAM mode Single carrier [dB]
0.7
Dual carrier [dB[ 1.2
Installation and mechanical specifications Table 268
FRMF installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation
DN0951745 Issue: 25
© 2017 Nokia
201
Descriptions of 6TX RF Modules
Table 268
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRMF installation and mechanical specifications (Cont.) Property
Value • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 269
FRMF dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 270
FRMF environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs
202
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 271
Descriptions of 6TX RF Modules
FRMF LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
DN0951745 Issue: 25
© 2017 Nokia
203
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 271
FRMF LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: All fans are working Green RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.9 Flexi RFM 6-pipe 1450 360 W (FRSA) FRSA technical specifications. Functional description Table 272
FRSA functional specification Property
Value
Output power
6x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1452-1492 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
40 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
40 MHz
UL filter bandwidth
30 MHz
Interfaces
204
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 56
FRSA interfaces
ANT 7TX ANT 10RX ANT 9TX ANT 12RX ANT 11TX
ANT 8RX ANT 3TX ANT 6RX ANT 4RX ANT 5TX ANT 1TX RET ANT 2RX
LED Module Status
OPT3
DCIN
EAC OPT1
GND
Table 273
Descriptions of 6TX RF Modules
GND
Fan/RF Status OPT 2
FRSA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT TX
6
7/16
-
Antenna connector
ANT RX
6
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
1.5 Gbps or 6 Gbps
Antenna Line Devices (ALDs) support
g
Note: ALD support is for TX antenna ports (band 32) only. Table 274
FRSA ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V
© 2017 Nokia
205
Descriptions of 6TX RF Modules
Table 274
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRSA ALD support (Cont.)
ALD support via antenna ports
Value RET: 25 V
Power per port
30 W
Functional block diagram Figure 57
FRSA functional block diagram RFModule
Filter PA TXRF
Bias-T
TX filter
PA Main
VSWR
Tx
Det
PA Div
EAC LNA
RXRF RXDiv
LNA
TXRF
OpticalIF
Rx Bias-T
TX filter
PA Main
Tx
Det
RX filter
PA OpticalIF
Rx VSWR
TX filter
RXMain
RET
RX filter
VSWR
Tx
Det
PA Div
RF
control
LNA
RXRF
RX filter TX filter
RXMain RXDiv
OpticalIF LNA
Rx Bias-T
TX filter
PA Main
Tx
Det
RX filter
PA TXRF
Rx VSWR
VSWR
Tx
Det
PA Div
LNA
RXRF RXDiv
LNA
Rx VSWR
TX filter
RXMain
DCIN
RX filter
Tx
Det
RX filter
Rx
PSU
Fanassembly
Electrical specifications Table 275
FRSA electrical specifications Property
206
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 275
Descriptions of 6TX RF Modules
FRSA electrical specifications (Cont.) Property
Value -57.0 V DC to -60.0 V DC
Power consumption Table 276 Mode
FRSA power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption ETSI ES 202706 average load PRRH, static
g LTE
Table 277
ETSI ES 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
Note: Values estimated.
1/1/1 2T2R
20+20
414
478
610
1/1/1 2T2R
40+40
540
661
935
1/1/1 2T2R
60+60
704
893
1328
Recommended FRSA power backoff in 256 QAM mode Single carrier [dB]
0.6
Dual carrier [dB] 1.2
Installation and mechanical specifications Table 278
FRSA installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation •
DN0951745 Issue: 25
© 2017 Nokia
Flexi Mounting Kit for Floor, Wall and Pole (FMFA)
207
Descriptions of 6TX RF Modules
Table 278
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRSA installation and mechanical specifications (Cont.) Property
Value •
Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 279
FRSA dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 280
FRSA environmental specifications Property
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
208
© 2017 Nokia
Value +55°C (131°F)
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 280
Descriptions of 6TX RF Modules
FRSA environmental specifications (Cont.) Property
Value
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 281
FRSA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded due to external factors (for example, VSWR minor/major
Alarm
© 2017 Nokia
209
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 281
FRSA LEDs (Cont.) LED color
Description
Alarm
values exceeded, Antenna line device faulty/degraded) Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.10 Flexi RFM 6-pipe 1800 360 W (FXED) FXED technical specifications. Functional description Table 282
FXED functional specification Property
210
Value
Output power
6x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
GSM, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
60 MHz in LTE, LTE/GSM Sharing
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 282
Descriptions of 6TX RF Modules
FXED functional specification (Cont.) Property
Value 40 MHz in GSM* *Single-RAT GSM support enabled on version A20x onwards.
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces Figure 58
FXED interfaces
RXO3 ANT6 TX/RX
EAC OPT1 LED Module Status
Ground
Table 283
ANT3 TX/RX
ANT1 TX/RX
ANT2 TX/RX
RET
RXO1
DCIN OPT3
Fan/RF Status OPT2
FXED interfaces
Interface
DN0951745 Issue: 25
ANT 5 TX/RX RXO2 ANT4 TX/RX
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
3 Gbps or 6 Gbps
© 2017 Nokia
211
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Antenna Line Devices (ALDs) support Table 284
FXED ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 25 V
Power per port
30 W
Functional block diagram Figure 59
FXED functional block diagram RFModule
Filter PA TXRF
TX filter
PA Main
Bias-T
PA Div
EAC LNA
RXRF RET
RXDiv
PA TXRF
LNA
Bias-T
OpticalIF
RF
control
LNA
RXRF
Bias-T
RXDiv
OpticalIF PA TXRF
LNA
Bias-T
LNA
Bias-T
RXDiv
LNA
DCIN
Tx/Rx
VSWR Det
RX filter
Tx/Rx
RxOUT TX filter
RXMain
VSWR Det
RX filter
PA Div
RXRF
Tx/Rx
RxOUT
TX filter
PA Main
Tx/Rx
VSWR Det
RX filter TX filter
RXMain
VSWR Det
RX filter
PA Div
OpticalIF
Tx/Rx
RxOUT
TX filter
PA Main
Det
RX filter TX filter
RXMain
VSWR
RX filter
Bias-T
VSWR Det
Tx/Rx
PSU
Fanassembly
Electrical specifications
212
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 285
Descriptions of 6TX RF Modules
FXED electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 286 Mode
FXED power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
LTE
MSR
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
390
390
390
390
390
390
2/2/2
20
422
451
547
447
452
457
4/4/4
20
549
666
935
635
661
691
1/1/1 2T2R
20+20
406
472
608
1/1/1 2T2R
40+40
522
643
912
1/1/1 2T2R
60+60
669
854
1272
GSM 2/2/2
20
632
721
964
791
997
1352
20+20
LTE 1/1/1 2T2R 10 MHz GSM 4/4/4
20 20+20
LTE 1/1/1 2T2R 10 MHz
DN0951745 Issue: 25
© 2017 Nokia
213
Descriptions of 6TX RF Modules
Table 286 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FXED power consumption (Cont.) Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM 4/4/4
15
707
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
868
Power consum ption
1210
20+20
LTE 1/1/1 2T2R 20 MHz
Table 287
Recommended FXED power backoff in 256 QAM mode Single carrier [dB]
1.0
Dual carrier [dB] 1.3
Installation and mechanical specifications Table 288
FXED installation and mechanical specifications Property
Installation options
Value •
floor/stack installation
•
pole installation
•
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation
214
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 288
Descriptions of 6TX RF Modules
FXED installation and mechanical specifications (Cont.) Property
Value • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 289
FXED dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications Table 290
FXED environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs
DN0951745 Issue: 25
© 2017 Nokia
215
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 291
FXED LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
216
Alarm
© 2017 Nokia
No alarm
-
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 291
Descriptions of 6TX RF Modules
FXED LEDs (Cont.) LED color
Description
Alarm
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
8.11 Flexi RFM 6-pipe 2100 360 W (FRGU) FRGU technical specifications. Functional description Table 292
FRGU functional specification Property
Value
Output power
6x60 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
217
Descriptions of 6TX RF Modules
Figure 60
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGU interfaces
RXO3 ANT6 TX/RX
EAC OPT1 LED Module Status
Ground
Table 293
ANT 5 TX/RX RXO2 ANT4 TX/RX
ANT3 TX/RX
ANT1 TX/RX
ANT2 TX/RX
RET
RXO1
DCIN OPT3
Fan/RF Status OPT2
FRGU interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
6
7/16
-
RF output connector
RxO
3
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
MDR36
-
Optical interface
OPT
3
SFP
1.5 Gbps to 6 Gbps
Antenna Line Devices (ALDs) support Table 294
FRGU ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, ANT5, RET: AISG 2.0
CWA (for non-AISG installations)
Yes
Voltage
ANT1, ANT3, ANT5: 25 V or 12 V ANT2, ANT4, ANT6: 12 V
218
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 294
Descriptions of 6TX RF Modules
FRGU ALD support (Cont.)
ALD support via antenna ports
Value RET: 25 V
Power per port
30 W
Functional block diagram Figure 61
FRGU functional block diagram RFModule
Filter PA TXRF
TX filter
PA Main
Bias-T
PA Div
EAC LNA
RXRF RET
RXDiv
PA TXRF
LNA
Bias-T
OpticalIF
LNA
RXRF
RF
control
Bias-T
RXDiv
OpticalIF PA TXRF
LNA
Bias-T
LNA
Bias-T
RXDiv
LNA
DCIN
Tx/Rx
VSWR Det
RX filter
Tx/Rx
RxOUT TX filter
RXMain
VSWR Det
RX filter
PA Div
RXRF
Tx/Rx
RxOUT
TX filter
PA Main
Tx/Rx
VSWR Det
RX filter TX filter
RXMain
VSWR Det
RX filter
PA Div
OpticalIF
Tx/Rx
RxOUT
TX filter
PA Main
Det
RX filter TX filter
RXMain
VSWR
RX filter
Bias-T
VSWR Det
Tx/Rx
PSU
Fanassembly
Electrical specifications Table 295
FRGU electrical specifications Property
DN0951745 Issue: 25
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC
© 2017 Nokia
219
Descriptions of 6TX RF Modules
Table 295
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGU electrical specifications (Cont.) Property
Value -57.0 V DC to -60.0 V DC
Power consumption Table 296 Mode
FRGU power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
MSR
ETSI 202706 busy hour load PBH RRH, static
100% RF power load P100% RRH
1/1/1
20
275
309
383
2/2/2
20
340
399
540
3/3/3
20
413
499
706
1/1/1 2T2R
20+20
422
497
649
1/1/1 2T2R
40+40
552
685
967
1/1/1 2T2R
60+60
702
900
1340
558
682
974
697
871
1294
WCDMA 2/2/2 20 LTE 1/1/1 2T2R 10 MHz
20+20
WCDMA 2/2/2 40 LTE 1/1/1 2T2R 10 MHz
Table 297
ETSI 202706 average load PRRH, static
Power consumption
20+20
Recommended FRGU power backoff in 256 QAM mode Single carrier [dB]
0.7
Dual carrier [dB] 1.3
Installation and mechanical specifications Table 298
FRGU installation and mechanical specifications Property
Installation options
220
© 2017 Nokia
Value •
floor/stack installation
•
pole installation
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 298
Descriptions of 6TX RF Modules
FRGU installation and mechanical specifications (Cont.) Property
Value •
wall installation
•
19'' rack/cabinet
IP rating
IP65
Related optional items
Pole installation
•
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Pole Kit (FPKA)
•
Flexi Pole Kit (FPKC)
•
Flexi Module Casing (EMHx)
•
Floor/Wall installation • •
Flexi Mounting Kit for Floor, Wall and Pole (FMFA) Flexi Module Casing (EMHx)
Outdoor 19'' rack •
Flexi Module Casing (EMHx)
Cabinet/indoor 19''' rack •
No optional items needed
Dimensions and weight Table 299
FRGU dimensions and weight Property
Value
Height
Core RFM: 115 mm (4.5 in.)
Depth
Core RFM: 400 mm (15.7 in.)
Dimensions orientation
Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width
height width
depth
Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.)
Weight
24 kg (52.9 lb)
Volume
19.3 l
Environmental specifications
DN0951745 Issue: 25
© 2017 Nokia
221
Descriptions of 6TX RF Modules
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 300
FRGU environmental specifications Property
Value
Maximum operational outdoor temperature (at constant high ambient temperature maximum output power might be limited)
+55°C (131°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 301
FRGU LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
222
Alarm
Major alarm affecting the whole RF Module Major alarm affecting the whole RF Module Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 301
Descriptions of 6TX RF Modules
FRGU LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
RF Module fan/TX status LED: At least one fan is faulty or Red degraded
-
RF Module fan/TX status LED: All fans are working Green
-
RF Module fan/TX status LED: RF transmission is ON Color set according to fan status, stable
-
RF Module fan/TX status LED: RF transmission is OFF Color set according to fan status, blinking
-
Warnings, cautions or notes related to the product
f
g
DN0951745 Issue: 25
WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
223
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
9 Descriptions of Flexi Metro RRH 9.1 Flexi Metro RRH 2-pipe 900H 10 W (FHDG) FHDG technical specifications. Functional description Table 302
FHDG functional specification Property
Value
Output power
2x5 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
FDD-LTE
TX frequency range
945-960 MHz
RX frequency range
900-915 MHz
DL instantaneous bandwidth
15 MHz
(supported but not tested due to limitation of UE) UL instantaneous bandwidth
15 MHz
(supported but not tested due to limitation of UE) DL filter bandwidth
15 MHz
UL filter bandwidth
15 MHz
Interfaces
224
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 62
Descriptions of Flexi Metro RRH
FHDG interfaces
ANT2
OPT2 Table 303
OPT1
ANT1
Ground
FAN
ACIN
FHDG interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
AC IN
1
MicroFit 1x3P Plug
-
Antenna connector
ANT
2
4.3-10
-
Fan control
FAN
1
8-pin circular
Power and control for fan option
Optical interface
OPT
2
SFP
3 Gbps to 6 Gbps, OBSAI
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 304
FHDG ALD support
ALD support via antenna ports AISG
Value None
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
225
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 63
FHDG functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
LNA
TXRF RFcontrol
PA
LMP
FBRX
FAN
RX
TXfilter
RXfilter LNA
TXRF
AC IN
PA
TXfilter
PSU
Electrical specifications Table 305
FHDG electrical specifications Property
Value
Nominal input voltage range
100 V AC to 240 V AC
Extended input voltage range
88 V AC to 276 V DC
Power consumption Table 306 Mode
FHDG power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
1/1/1 2T2R
5+5
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
196
213
Power consumption 100% RF power load P100% RRH
246
Installation and mechanical specifications
226
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 307
Descriptions of Flexi Metro RRH
FHDG installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
rooftop installation
•
bookshelf/stacking installation
IP rating
IP65
Related optional items
•
•
Flexi Metro Wall/Pole/Stacking Mounting Kit (FMDB) Flexi Metro Wall/Bookshelf Mounting Kit (FMDD) Flexi Metro Visual Cover (FMDE)
•
Flexi Metro Fan Assembly Kit (FMDF)
•
Flexi Pole Mounting Kit (FPKA), not recommended
•
Dimensions and weight Table 308
FHDG dimensions and weight Property
Value
Height
Without mounting brackets, flange, screw boss and connectors: 269 mm (10.6 in.)
Depth
Without mounting brackets, flange, screw boss and connectors: 77 mm (3.0 in.)
Width
Without mounting brackets, flange, screw boss and connectors: 202 mm (7.9 in.)
Weight
Without mounting brackets: <5 kg (11.0 Ib)
Volume
<5 l
Dimensions orientation
height width depth
Environmental specifications Table 309
FHDG environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational ambient temperature (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational ambient temperature
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
© 2017 Nokia
227
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
LEDs Table 310
FHDG LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
228
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of Flexi Metro RRH
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure convection cooling.
g
Note: The RRH with optional fan module can be mounted in horizontal orientation.
9.2 Flexi Metro RRH 2-pipe 1800 10 W (FHEE) FHEE technical specifications. Functional description Table 311
FHEE functional specification Property
Value
Output power
2x5 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces Figure 64
FHEE interfaces
ANT2
OPT2
DN0951745 Issue: 25
OPT1
FAN
© 2017 Nokia
ANT1
Ground
ACIN
229
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 312
FHEE interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
AC IN
1
MicroFit 1x3P Plug
-
Antenna connector
ANT
2
4.3-10
-
Fan control
FAN
1
8-pin circular
Power and control for fan option
Optical interface
OPT
2
SFP
3 Gbps to 6 Gbps, OBSAI
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 313
FHEE ALD support
ALD support via antenna ports
Value
AISG
None
Functional block diagram Figure 65
FHEE functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
LNA
TXRF RFcontrol
PA
LMP
FBRX
FAN
RX
TXfilter
RXfilter LNA
TXRF
AC IN
PA
TXfilter
PSU
Electrical specifications Table 314
FHEE electrical specifications Property
Nominal input voltage range
230
Value 100 V AC to 240 V AC
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 314
Descriptions of Flexi Metro RRH
FHEE electrical specifications (Cont.) Property
Value
Extended input voltage range
88 V AC to 276 V DC
Power consumption Table 315 Mode
FHEE power consumption Configuration Output power per carrier [W]
Estimated power consumption [W] at 230VAC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption ETSI 202706 average load PRRH, static
g LTE
1/1/1 2T2R
5+5
217
Power consumption
ETSI 202706 busy hour load PBH RRH, static
100% RF power load P100% RRH
Note: Values preliminary estimated. 238
272
Installation and mechanical specifications Table 316
FHEE installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
rooftop installation
•
bookshelf/stacking installation
IP rating
IP65
Related optional items
• • • • • •
Flexi Metro Wall/Pole/Stacking Mounting Kit (FMDB) Flexi Metro Wall/Bookshelf Mounting Kit (FMDD) Flexi Metro Visual Cover (FMDE) Flexi Metro Integrated Antenna (1.7G2.2G) (FAGH) Flexi Metro Fan Assembly Kit (FMDF) Flexi Pole Mounting Kit (FPKA), not recommended
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
231
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 317
FHEE dimensions and weight Property
Value
Height
Without mounting brackets, flange, screw boss and connectors: 269 mm (10.6 in.)
Depth
Without mounting brackets, flange, screw boss and connectors: 77 mm (3.0 in.)
Width
Without mounting brackets, flange, screw boss and connectors: 202 mm (7.9 in.)
Weight
Without mounting brackets: <5 kg (11.0 Ib)
Volume
<5 l
Dimensions orientation
height width depth
Environmental specifications Table 318
FHEE environmental specifications Property
Value
Maximum operational ambient temperature (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational ambient temperature
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 319
FHEE LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
232
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 319
Descriptions of Flexi Metro RRH
FHEE LEDs (Cont.) LED color
Description • •
Yellow, blinking
• •
Green, stable
•
•
Alarm
The carriers are blocked from BTS There is no connection to any System Module Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w g
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure convection cooling. The RRH with optional fan module can be mounted in horizontal orientation. Note: The RRH with optional fan module can be mounted in horizontal orientation.
9.3 Flexi Metro RRH 2-pipe 1800L 10 W (FHEI) FHEI technical specifications. Functional description
DN0951745 Issue: 25
© 2017 Nokia
233
Descriptions of Flexi Metro RRH
Table 320
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FHEI functional specification Porperty
Value
Output power
2x5 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1805-1865 MHz
RX frequency range
1710-1770 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces Figure 66
FHEI interfaces
ANT2
OPT2 Table 321
Ground
FAN
ACIN
FHEI interfaces
Interface
234
OPT1
ANT1
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
AC IN
1
MicroFit 1x3P Plug
-
Antenna connector
ANT
2
4.3-10
-
Fan control
FAN
1
8-pin circular
Power and control for fan option
Optical interface
OPT
2
SFP
3 Gbps to 6 Gbps, OBSAI
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 321
Descriptions of Flexi Metro RRH
FHEI interfaces (Cont.)
Interface
Label on the HW
Local LMP Management Port
Number of interfaces 1
Connector type 2x15 pin header
Additional info -
Antenna Line Devices (ALDs) support Table 322
FHEI ALD support
ALD support via antenna ports
Value
AISG
None
Functional block diagram Figure 67
FHEI functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
LNA
TXRF RFcontrol
PA
LMP
FBRX
FAN
RX
TXfilter
RXfilter LNA
TXRF
AC IN
PA
TXfilter
PSU
Electrical specifications Table 323
FHEI electrical specifications Property
Value
Nominal input voltage range
100 V AC to 240 V AC
Extended input voltage range
88 V AC to 276 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
235
Descriptions of Flexi Metro RRH
Table 324 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FHEI power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Values preliminary estimated. Power Power consumption consumption ETSI 202706 average load PRRH, static
g LTE
1/1/1 2T2R
5+5
217
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
Note: Values preliminary estimated. 238
272
Installation and mechanical specifications Table 325
FHEI installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
rooftop installation
•
bookshelf/stacking installation
IP rating
IP65
Related optional items
•
•
Flexi Metro Wall/Pole/Stacking Mounting Kit (FMDB) Flexi Metro Wall/Bookshelf Mounting Kit (FMDD) Flexi Metro Visual Cover (FMDE)
•
Flexi Metro Fan Assembly Kit (FMDF)
•
Flexi Pole Mounting Kit (FPKA), not recommended Flexi Metro Integrated Antenna (1.7G2.2G) (FAGH)
•
•
Dimensions and weight
236
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 326
Descriptions of Flexi Metro RRH
FHEI dimensions and weight Property
Value
Height
Without mounting brackets, flange, screw boss and connectors: 269 mm (10.6 in.)
Depth
Without mounting brackets, flange, screw boss and connectors: 82.7 mm (3.2 in.)
Width
Without mounting brackets, flange, screw boss and connectors: 202 mm (7.9 in.)
Weight
Without mounting brackets: 5 kg (11.0 Ib)
Volume
4.2 l
Dimensions orientation
height width depth
Environmental specifications Table 327
FHEI environmental specifications Property
Value
Maximum operational ambient temperature (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational ambient temperature
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 328
FHEI LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
DN0951745 Issue: 25
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins
© 2017 Nokia
No alarm
237
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 328
FHEI LEDs (Cont.) LED color
Description • •
Yellow, blinking
• •
Green, stable
•
•
Alarm
The carriers are blocked from BTS There is no connection to any System Module Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure convection cooling.
g
Note: The RRH with optional fan module can be mounted in horizontal orientation.
9.4 Flexi Metro RRH 2-pipe 2100 10 W (FHGA) FHGA technical specifications. Functional description
238
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 329
Descriptions of Flexi Metro RRH
FHGA functional specification Property
Value
Output power
2x5 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces Figure 68
FHGA interfaces
ANT2
OPT2 Table 330
Ground
FAN
ACIN
FHGA interfaces
Interface
DN0951745 Issue: 25
OPT1
ANT1
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
AC IN
1
MicroFit 1x3P Plug
-
Antenna connector
ANT
2
4.3-10
-
Fan control
FAN
1
8-pin circular
Power and control for fan option
Optical interface
OPT
2
SFP
3 Gbps to 6 Gbps, OBSAI
© 2017 Nokia
239
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 330
FHGA interfaces (Cont.)
Interface
Label on the HW
Local LMP Management Port
Number of interfaces 1
Connector type 2x15 pin header
Additional info -
Antenna Line Devices (ALDs) support Table 331
FHGA ALD support
ALD support via antenna ports
Value
AISG
None
Functional block diagram Figure 69
FHGA functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
LNA
TXRF RFcontrol
PA
LMP
FBRX
FAN
RX
TXfilter
RXfilter LNA
TXRF
AC IN
PA
TXfilter
PSU
Electrical specifications Table 332
FHGA electrical specifications Property
Value
Nominal input voltage range
100 V AC to 240 V AC
Extended input voltage range
88 V AC to 276 V DC
Power consumption
240
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 333 Mode
Descriptions of Flexi Metro RRH
FHGA power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
1/1/1 2T2R
5+5
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
215
232
Power consumption 100% RF power load P100% RRH
260
Installation and mechanical specifications Table 334
FHGA installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
rooftop installation
•
bookshelf/stacking installation
IP rating
IP65
Related optional items
• • • • • •
Flexi Metro Wall/Pole/Stacking Mounting Kit (FMDB) Flexi Metro Wall/Bookshelf Mounting Kit (FMDD) Flexi Metro Visual Cover (FMDE) Flexi Metro Integrated Antenna (1.7G2.2G) (FAGH) Flexi Metro Fan Assembly Kit (FMDF) Flexi Pole Mounting Kit (FPKA), not recommended
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
241
Descriptions of Flexi Metro RRH
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 335
FHGA dimensions and weight Property
Value
Height
Without mounting brackets, flange, screw boss and connectors: 269 mm (10.6 in.)
Depth
Without mounting brackets, flange, screw boss and connectors: 77 mm (3.0 in.)
Width
Without mounting brackets, flange, screw boss and connectors: 202 mm (7.9 in.)
Weight
Without mounting brackets: <5 kg (11.0 Ib)
Volume
4.2 l
Dimensions orientation
height width depth
Environmental specifications Table 336
FHGA environmental specifications Property
Value
Maximum operational ambient temperature (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational ambient temperature
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 337
FHGA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
242
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 337
Descriptions of Flexi Metro RRH
FHGA LEDs (Cont.) LED color
Description • •
Yellow, blinking
• •
Green, stable
•
•
Alarm
The carriers are blocked from BTS There is no connection to any System Module Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w g
DN0951745 Issue: 25
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure convection cooling. The RRH with optional fan module can be mounted in horizontal orientation. Note: The RRH with optional fan module can be mounted in horizontal orientation.
© 2017 Nokia
243
Flexi Remote Radio Head 1TX 2100 (FRGG)
Flexi Multiradio BTS RF Module and Remote Radio Head Description
10 Flexi Remote Radio Head 1TX 2100 (FRGG) FRGG technical specifications. Functional description Table 338
FRGG functional specification Property
Value
Output power
1x60 W
MIMO
1TX
Outdoor installation
Yes
SW supported technology
WCDMA
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
45 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
20 MHz
Interfaces Figure 70
FRGG (471882A) interfaces
LED Module Status DCIN
ANT2 TX/RX
244
EAC
RET
RF Status LMT
Test
OPT1
OPT2
ANT1 RX
Ground
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 339
Flexi Remote Radio Head 1TX 2100 (FRGG)
FRGG (471882A) interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power Connector DC IN
1
2-pin ITT Cannon Optional DC connection box (FPOC) 16mm²
Antenna connector
ANT
2
7/16, female
Remote Electrical RET Tilt
1
8-pin Amphenol C 091 D
External Alarm Connection
EAC
1
14-pin Amphenol C 091 D
-
Optical interface
OPT
2
SFP
OBSAI
Local Maintenance Terminal
LMT
1
RJ-45
-
-
Antenna Line Devices (ALDs) support Table 340
FRGG ALD support
ALD support via antenna ports
Value
AISG
RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 28.5 V or 12 V ANT2: 12 V
Power per port
30 W
Functional block diagram Figure 71
FRGG functional block diagram
OpticalIF
RX Main
RXfilter
OpticalIF
VSWR
Tx/Rx
LNA Det
TXRF
PA
TXfilter
RFcontrol EAC
VSWR
RX Diversity
Rx
Det
LNA
RET
DCIN
RXfilter
PSU
Electrical specifications
DN0951745 Issue: 25
© 2017 Nokia
245
Flexi Remote Radio Head 1TX 2100 (FRGG)
Table 341
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGG electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 342
FRGG power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
1
100% RF Load
60
212
290
40
183
240
20
150
184
Installation and mechanical specifications Table 343
FRGG installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
246
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 344
Flexi Remote Radio Head 1TX 2100 (FRGG)
FRGG dimensions and weight Property
Value
Height
Dimensions orientation
450 mm (17.7 in.) With solar shield: 500 mm (19.7 in.)
Depth
159 mm (6.3 in.) With solar shield: 174 mm (6.8 in.)
Width
260 mm (10.2 in.) height
With solar shield: 280.5 mm (11.0 in.) Weight
15.9 kg (35.0 lb)
Volume
17.9 l
width depth
Environmental specifications Table 345
FRGG environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 346
FRGG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module
© 2017 Nokia
247
Flexi Remote Radio Head 1TX 2100 (FRGG)
Table 346
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGG LEDs (Cont.) LED color
Description
Alarm
subcomponent or antenna carrier Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
248
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 2TX RRHs
11 Descriptions of 2TX RRHs 11.1 Flexi Remote Radio Head 2TX 850 (FHCA) FHCA technical specifications. Functional description Table 347
FHCA functional specification Property
Value
Output power
2x20 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
869-894 MHz
RX frequency range
824-849 MHz
DL instantaneous bandwidth
15 MHz
UL instantaneous bandwidth
15 MHz
DL filter bandwidth
25 MHz
UL filter bandwidth
25 MHz
Interfaces Figure 72
FHCA interfaces
DC IN
OPT1
PWR
+V48RTN
-V48N
LMP
ANT1
DN0951745 Issue: 25
RET
OPT2
MAIN
EAC
ANT2
© 2017 Nokia
249
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 348
FHCA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps
Antenna Line Devices (ALDs) support Table 349
FHCA ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT2, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT2: 14.5 V RET: 14.5 V
Power per port
17 W
Functional block diagram Figure 73
FHCA functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
VSWR Det
TXRF
DCIN
Bias-T
LNA
RET
PA
TXfilter
PSU
Electrical specifications
250
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 350
Descriptions of 2TX RRHs
FHCA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 351
FHCA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
2
Table 352
20
100% RF Load
200
240
Recommended FHCA power backoff in 256 QAM mode Single carrier [dB]
0.7
Installation and mechanical specifications Table 353
FHCA installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
251
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 354
FHCA dimensions and weight Property
Value
Height
Dimensions orientation
As delivered, cable tie point recessed: 579 mm (22.7 in.) As installed, cable tie point released due to brackets and solar shields: 733 mm (28.8 in.)
Depth
215 mm (8.4 in.)
Width
358 mm (14.1 in.)
Weight
20 kg (44 Ib)
width
Volume
18 l
depth
height
Environmental specifications Table 355
FHCA environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 356
FHCA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• •
252
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 356
Descriptions of 2TX RRHs
FHCA LEDs (Cont.) LED color
Description
Yellow, stable
•
Major/Critical alarm affecting a module subcomponent or antenna carrier
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
• •
Yellow, blinking
• •
Green, stable
•
•
Alarm
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
253
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
11.2 Flexi Remote Radio Head 2TX 730 (FRLB) FRLB technical specifications. Functional description Table 357
FRLB functional specification Property
Value
Output power
2x30 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
729-745 MHz
RX frequency range
699-715 MHz
DL instantaneous bandwidth
16 MHz
UL instantaneous bandwidth
16 MHz
DL filter bandwidth
16 MHz
UL filter bandwidth
16 MHz
Interfaces Figure 74
EAC
254
FRLB interfaces
ANT2
RXO2
LMP
Ground
RET
© 2017 Nokia
RXO1
OPT1
ANT1
OPT2
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 358
Descriptions of 2TX RRHs
FRLB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 359
FRLB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT2, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT2: 24 V RET: 24 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
255
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 75
FRLB functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 360
FRLB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 361
FRLB power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
2
Table 362
100% RF Load
30
248
321
20
192
239
Recommended FRLB power backoff in 256 QAM mode Single carrier [dB]
0.9
Dual carrier [dB] 1.5
Installation and mechanical specifications
256
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 363
Descriptions of 2TX RRHs
FRLB installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 364
FRLB dimensions and weight Property
Value
Height
400 mm (15.7 in.)
Depth
150 mm (5.9 in.)
Width
400 mm (15.7 in.)
Weight
Without solar shield and mounting shroud: 27 kg (59.5 Ib)
Volume
25 l
Dimensions orientation
height width depth
Environmental specifications Table 365
FRLB environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs
DN0951745 Issue: 25
© 2017 Nokia
257
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 366
FRLB LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
258
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 2TX RRHs
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.3 Flexi RRH 2-pipe 900 80 W (FHDA) FHDA technical specifications. Functional description Table 367
FHDA functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA
TX frequency range
925-960 MHz
RX frequency range
880-915 MHz
DL instantaneous bandwidth
A.10x version: 25 MHz A.20x version: 30.2 MHz
UL instantaneous bandwidth
35 MHz
DL filter bandwidth
35 MHz
UL filter bandwidth
35 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
259
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 76
FHDA interfaces
RET
ANT2
Grounding points
ANT1
DCINPUT
OPT2
MOD (LEDModulestatus) Table 368
EAC
OPT1
Tx (LED Txstatus)
FHDA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 369
FHDA ALD support
ALD support via antenna ports
260
Value
AISG
ANT1, ANT2, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT2: 14.5 V
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 369
Descriptions of 2TX RRHs
FHDA ALD support (Cont.)
ALD support via antenna ports
Value RET: 14.5 V
Power per port
30 W
Functional block diagram Figure 77
FHDA functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 370
FHDA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 371
FHDA power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
2
DN0951745 Issue: 25
100% RF Load
40
305
344
20
192
233
© 2017 Nokia
261
Descriptions of 2TX RRHs
Table 372
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FHDA power backoff in 256 QAM mode Single carrier
Dual carrier
0.8
0.9
Installation and mechanical specifications Table 373
FHDA installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 374
FHDA dimensions and weight Property
Value
Height
Dimensions orientation
As delivered, cable tie point recessed: 579 mm (22.7 in.) As installed, cable tie point released due to brackets and solar shields: 733 mm (28.8 in.)
Depth
215 mm (8.4 in.)
Width
358 mm (14.1 in.)
Weight
20 kg (44.0 Ib)
width
Volume
25 l
depth
height
Environmental specifications Table 375
FHDA environmental specifications Property
262
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 375
Descriptions of 2TX RRHs
FHDA environmental specifications (Cont.) Property
Value
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 376
FHDA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
263
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 376
FHDA LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.4 Flexi Remote Radio Head 2TX 1800 (FHEA) FHEA technical specifications. Functional description Table 377
FHEA functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
A.10x version: 23 MHz A.20x version: 25 MHz
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces
264
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 78
Descriptions of 2TX RRHs
FHEA interfaces
RET
ANT2
Grounding points
ANT1
DCINPUT
OPT2
MOD (LEDModulestatus) Table 378
EAC
OPT1
Tx (LED Txstatus)
FHEA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 379
FHEA ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
ANT1, ANT2, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT2: 14.5 V
© 2017 Nokia
265
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 379
FHEA ALD support (Cont.)
ALD support via antenna ports
Value RET: 14.5 V
Power per port
30 W
Functional block diagram Figure 79
FHEA functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 380
FHEA electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
266
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 381 Mode
Descriptions of 2TX RRHs
FHEA power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 382
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
8+8
526
570
652
1/1/1 2T2R
20+20
612
700
870
1/1/1 2T2R
40+40
821
971
1289
Recommended FHEA power backoff in 256 QAM mode Single carrier
0.2
Dual carrier 0.9
Installation and mechanical specifications Table 383
FHEA installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
267
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 384
FHEA dimensions and weight Property
Value
Height
Dimensions orientation
As delivered, cable tie point recessed: 579 mm (22.7 in.) As installed, cable tie point released due to brackets and solar shields: 733 mm (28.8 in.)
Depth
215 mm (8.4 in.)
Width
358 mm (14.1 in.)
Weight
20 kg (44.0 Ib)
width
Volume
25 l
depth
height
Environmental specifications Table 385
FHEA environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 386
FHEA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• •
268
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 386
Descriptions of 2TX RRHs
FHEA LEDs (Cont.) LED color
Description
Yellow, stable
•
Major/Critical alarm affecting a module subcomponent or antenna carrier
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
• •
Yellow, blinking
• •
Green, stable
•
•
Alarm
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
269
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
11.5 Flexi Remote Radio Head 2TX 2100 (FRGQ) FRGQ technical specifications. Functional description Table 387
FRGQ functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces Figure 80
FRGQ interfaces
ANT2
EAC
270
LMP
RXO2
RXO1
OPT2
© 2017 Nokia
OPT1
ANT1
RET
DCIN
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 388
Descriptions of 2TX RRHs
FRGQ interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 389
FRGQ ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT2, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT2: 14.5 V RET: 14.5 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
271
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 81
FRGQ functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 390
FRGQ electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 391
FRGQ power consumption
Number of TXs
RF output power per Estimated power consumption [W] at 48VDC TX [W] input at 23°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin 50% RF Load
2
Table 392
100% RF Load
40
292
382
30
265
334
20
212
259
Recommended FRGQ power backoff in 256 QAM mode Single carrier
1.0
Installation and mechanical specifications
272
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 393
Descriptions of 2TX RRHs
FRGQ installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 394
FRGQ dimensions and weight Property
Value
Height
486 mm (19.1 in.)
Depth
155 mm (6.1 in.)
Width
324 mm (12.8 in.)
Weight
17 kg (37.5 Ib)
Volume
21 l
Dimensions orientation
height width depth
Environmental specifications Table 395
FRGQ environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs
DN0951745 Issue: 25
© 2017 Nokia
273
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 396
FRGQ LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
274
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 2TX RRHs
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.6 Flexi Remote Radio Head 2TX 2600 (FRHB) FRHB technical specifications. Functional description Table 397
FRHB functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2620-2690 MHz
RX frequency range
2500-2570 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
70 MHz
UL filter bandwidth
70 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
275
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 82
FRHB interfaces
RET
ANT2
Grounding points
ANT1
DCINPUT
OPT2
MOD (LEDModulestatus) Table 398
EAC
OPT1
Tx (LED Txstatus)
FRHB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
Rx EXT
2
SMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 399
FRHB ALD support
ALD support via antenna ports AISG
276
Value ANT1, RET: AISG 2.0
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 399
Descriptions of 2TX RRHs
FRHB ALD support (Cont.)
ALD support via antenna ports
Value
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
30 W
Functional block diagram Figure 83
FRHB functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 400
FRHB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
277
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 401 Mode
FRHB power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 402
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
597
687
873
1/1/1 2T2R
40+40
797
945
1263
Recommended FRHB power backoff in 256 QAM mode Single carrier
0.5
Dual carrier 0.8
Installation and mechanical specifications Table 403
FRHB installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
278
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 404
Descriptions of 2TX RRHs
FRHB dimensions and weight Property
Value
Height
514 mm (20.3 in.)
Depth
148 mm (5.8 in.)
Width
326 mm (12.8 in.)
Weight
Without solar shield and mounting shroud: 17.3 kg (38.1 Ib)
Volume
Dimensions orientation
height width
20 l depth
Environmental specifications Table 405
FRHB environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 406
FRHB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module
© 2017 Nokia
279
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 406
FRHB LEDs (Cont.) LED color
Description
Alarm
subcomponent or antenna carrier Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
280
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 2TX RRHs
11.7 Flexi Remote Radio Head 2TX 800EU (FRMB) FRMB technical specifications. Functional description Table 407
FRMB functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
791-821 MHz
RX frequency range
832-862 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces Figure 84
FRMB interfaces
ANT2
EAC
DN0951745 Issue: 25
LMP
RXO2
RXO1
OPT2
© 2017 Nokia
OPT1
ANT1
RET
DCIN
281
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 408
FRMB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
Rx EXT
2
SMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
3 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 409
FRMB ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
30 W
Functional block diagram
282
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 85
Descriptions of 2TX RRHs
FRMB functional block diagram
OpticalIF
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
PA
TXfilter RFloop
RFcontrol EAC
RX
RXfilter
Bias-T
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 410
FRMB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 411 Mode
FRMB power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
DN0951745 Issue: 25
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
486
549
667
1/1/1 2T2R
40+40
750
896
1170
© 2017 Nokia
283
Descriptions of 2TX RRHs
Table 412
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Recommended FRMB power backoff in 256 QAM mode Single carrier
Dual carrier
0.9
1.3
Installation and mechanical specifications Table 413
FRMB installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 414
FRMB dimensions and weight Property
Value
Height
514 mm (20.3 in.)
Depth
148 mm (5.8 in.)
Width
326 mm (12.8 in.)
Weight
Without solar shield and mounting shroud: 17.3 kg (38.1 Ib)
Volume
21 l
Dimensions orientation
height width depth
Environmental specifications Table 415
FRMB environmental specifications Property
284
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 415
Descriptions of 2TX RRHs
FRMB environmental specifications (Cont.) Property
Value
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 416
FRMB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
285
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 416
FRMB LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.8 Flexi RRH 2-pipe 700/840 100 W (FHPC) FHPC technical specifications. Functional description Table 417
FHPC functional specification Property
Value
Output power
B18: 2x30 W, B28: 2x20 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
B18: 860-875 MHz B28: 773-783 MHz
RX frequency range
B18: 815-830 MHz B28: 718-728 MHz
DL instantaneous bandwidth
B18: 15 MHz B28: 10 MHz
UL instantaneous bandwidth
B18: 15 MHz B28: 10 MHz
DL filter bandwidth
B18: 15 MHz B28: 10 MHz
286
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 417
Descriptions of 2TX RRHs
FHPC functional specification (Cont.) Property
Value
UL filter bandwidth
B18: 15 MHz B28: 10 MHz
Interfaces Figure 86
FHPC interfaces
AISG ANT0
LTEBBU Table 418
TXMON0
TXMON1
LTERRH
ANT1
CUSTI/O
FG
-48VDC
FHPC interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
-48V DC
1
Amphenol C016 20C003 100 12
-
Antenna connector
ANT 0
2
N-type
Connection to antenna line
RF external connector
TX MON 0
4
SMA-J
RX MON interfaces are inside of maintenance cover
ANT 1
TX MON 1 RX MON 0 RX MON 1
Antenna Control Interface
AISG
1
DDK AIC-M16R8SC
-
Optical interface
LTE BBU
2
SFP
CPRI interface to/from FSM
LTE RRH
CPRI interface to/from RRH 2.4 Gbps Customer Input/Output Connection
DN0951745 Issue: 25
CUST I/O
1
© 2017 Nokia
Amphenol PJ02S-21-26P
-
287
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 418
FHPC interfaces (Cont.)
Interface
Label on the HW
Grounding cable connection
Number of interfaces
FG
Frequency 10 MHz Reference Output
Connector type
Additional info
1
M6 blind holes with 16 mm spacing
-
1
SMA-J
Inside of maintenance cover
Antenna Line Devices (ALDs) support Table 419
FHPC ALD support
ALD support via antenna ports
Value
AISG
RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
RET: 27 V
Power per port
30 W
Functional block diagram Figure 87
FHPC functional block diagram Filter2xQuadroplexer
RRH
RXMON0
TXRF
CUST I/O
TX filter
PA
RX filter
RXRF LNA
STATUS(LED)
TXRF
PA
RX filter
RXRF CPRI1
LPF TX filter
ANT 0
TXMON0 VSWR
LNA
RF control
Det
TXRF
TX filter
PA
LNA
TXRF AISG
TXMON1
RX filter
RXRF
CPRI2
LPF
ANT 1
TX filter
PA
RX filter
RXRF LNA
RXMON1
DCIN
PSU
Electrical specifications
288
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 420
Descriptions of 2TX RRHs
FHPC electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.0 V DC to -56.0 V DC
Power consumption Table 421 Number of TXs
FHPC power consumption RF output power per TX [W]
700 MHz 2
Estimated power consumption [W] without AISG at 48VDC input at 23°C. Noncommitted estimated values depend on the final product HW and SW optimization with +/- 10% margin
800 MHz
50% RF Load
100% RF Load
20+20
-
155
220
-
30+30
199
310
20+20
30+30
275
455
20+20
20+20
253
408
Installation and mechanical specifications Table 422
FHPC installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Pole Mounting Bracket (FMFC)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
289
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 423
FHPC dimensions and weight Property
Value
Height
460 mm (18.1 in.)
Depth
136 mm (5.3 in.)
Width
350 mm (13.8 in.)
Dimensions orientation
height Weight
19.9 kg (43.9 lb)
width Volume
21.9 l
depth
Environmental specifications Table 424
FHPC environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum operational outdoor temperature in the sun
+45°C (113°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-30°C (-22°F)
LEDs Table 425
FHPC LEDs (RRH Status) LED color
Description
Red, stable
Critical alarm affecting the whole RF module
Fault
Red, blinking
Operation degraded
Major/critical alarm
Yellow, stable
•
Major alarm affecting the whole RF Module
•
Until software download begins The carriers are blocked from BTS
•
290
Alarm
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 425
Descriptions of 2TX RRHs
FHPC LEDs (RRH Status) (Cont.) LED color
Description
Yellow, blinking
•
There is no connection to any System Module
•
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
•
Green, stable
Alarm
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
Table 426
No alarm
FHPC LEDs (TX Status) LED color
Description
Alarm
Yellow, stable
O&M control is missing
No alarm
Green, stable
Transmission ON
No alarm
Green, blinking
Transmission OFF
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.0 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
291
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
11.9 Flexi Remote Radio Head 2TX 1800 (FHEB) FHEB technical specifications. Functional description Table 427
FHEB functional specification Property
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
For WCDMA/LTE when shared with GSM: 35/40 MHz LTE: 40 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces
292
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 88
LED
Descriptions of 2TX RRHs
FHEB interfaces
OPT2
OPT1
RET
ANT2 Table 428
EAC
DCIN
ANT1
FHEB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps
Antenna Line Devices (ALDs) support Table 429
FHEB ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
DN0951745 Issue: 25
© 2017 Nokia
293
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 429
FHEB ALD support (Cont.)
ALD support via antenna ports
Value
Power per port
15 W
Functional block diagram Figure 89
FHEB functional block diagram
OpticalIF RX
RXfilter
OpticalIF
VSWR
Bias-T
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 430
FHEB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
294
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 431 Mode
Descriptions of 2TX RRHs
FHEB power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
LTE
Table 432
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
538
538
538
538
538
538
2/2/2
20
547
567
655
546
549
553
4/4/4
20
884
1019
1267
777
801
829
8/8/8
15
973
1226
1521
1/1/1 2T2R
20+20
553
641
789
1/1/1 2T2R
40+40
689
831
1079
1/1/1 2T2R
60+60
875
1082
1462
Recommended FHEB power backoff in 256 QAM mode Single carrier
0.4
Dual carrier 0.8
Installation and mechanical specifications Table 433
FHEB installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
295
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 434 Property Height
FHEB dimensions and weight HW version
Value
A.101
Dimensions orientation
As delivered, cable tie point recessed: 335.2 mm (13.2 in.)
A.102
With lower mounting bracket in the "FMFA" position: 571 mm (22.5 in.) With lower mounting bracket in the alternative "ALT" position: 621 mm (24.4 in.) A.103
height
As delivered, cable tie point recessed: 425.8 mm (16.8 in.) width
With upper and lower mounting brackets: 572.1 mm (22.5 in.) Depth
A.101
depth
324 mm (12.8 in.)
A.102
Width
A.103
287 mm (11.3 in.)
A.101
260 mm (10.2 in.)
A.102
Weight
A.103
256.7 mm (10.1 in.)
A.101
17.3 kg (38.1 lb)
A.102
Volume
A.103
16.3 kg (35.9 lb)
A.101
21 l
A.102 A.103
19.1 l
Environmental specifications Table 435
FHEB environmental specifications Property
296
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 435
Descriptions of 2TX RRHs
FHEB environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s (this is valid for fanless products)
+40°C (104°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 436
FHEB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
297
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 436
FHEB LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.10 Flexi RRH 2-pipe 1800 120 W (FHEF) FHEF technical specifications. Functional description Table 437
FHEF functional specification Property
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, FDD-LTE
TX frequency range
1805-1860 MHz
RX frequency range
1710-1765 MHz
DL instantaneous bandwidth
For WCDMA/LTE when shared with GSM: 35/40 MHz LTE: 40 MHz
UL instantaneous bandwidth
55 MHz
DL filter bandwidth
55 MHz
UL filter bandwidth
55 MHz
Interfaces
298
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 90
LED
Descriptions of 2TX RRHs
FHEF interfaces
OPT2
OPT1
RET
ANT2 Table 438
EAC
DCIN
ANT1
FHEF interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Antenna Line Devices (ALDs) support Table 439
FHEF ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
DN0951745 Issue: 25
© 2017 Nokia
299
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 439
FHEF ALD support (Cont.)
ALD support via antenna ports
Value
Power per port
15 W
Functional block diagram Figure 91
FHEF functional block diagram
OpticalIF RX
RXfilter
OpticalIF
VSWR
Bias-T
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 440
FHEF electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
300
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 441 Mode
Descriptions of 2TX RRHs
FHEF power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption ETSI ES 202706 average load PRRH, static
LTE
Power consumption
ETSI ES 202706 busy hour load PBH RRH, static
100% RF power load P100% RRH
1/1/1 2T2R
20+20
565
650
801
1/1/1 2T2R
40+40
703
844
1107
1/1/1 2T2R
60+60
883
1091
1479
Installation and mechanical specifications Table 442
FHEF installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
301
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 443 Property Height
FHEF dimensions and weight HW version A.101
Value
Dimensions orientation
As delivered, cable tie point recessed: 335.2 mm (13.2 in.) With lower mounting bracket in the "FMFA" position: 571 mm (22.5 in.) With lower mounting bracket in the alternative "ALT" position: 621 mm (24.4 in.)
A.102
height
As delivered, cable tie point recessed: 425.8 mm (16.8 in.) width
With upper and lower mounting brackets: 572.1 mm (22.5 in.) Depth
Width
Weight
Volume
A.101
324 mm (12.8 in.)
A.102
287 mm (11.3 in.)
A.101
260 mm (10.2 in.)
A.102
256.7 mm (10.1 in.)
A.101
17.3 kg (38.1 lb)
A.102
16.3 kg (35.9 lb)
A.101
21 l
A.102
19.1 l
depth
Environmental specifications Table 444
FHEF environmental specifications Property
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s (this is valid for fanless products)
+40°C (104°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs
302
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 445
Descriptions of 2TX RRHs
FHEF LEDs LED color
Description
Alarm
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
DN0951745 Issue: 25
© 2017 Nokia
303
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.11 Flexi Remote Radio Head 2TX 900 (FHDB) FHDB technical specifications. Functional description Table 446
FHDB functional specification Property
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
GSM, WCDMA, FDD-LTE
TX frequency range
925-960 MHz
RX frequency range
880-915 MHz
DL instantaneous bandwidth
35 MHz
UL instantaneous bandwidth
35 MHz
DL filter bandwidth
35 MHz
UL filter bandwidth
35 MHz
Interfaces
304
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 92
LED
Descriptions of 2TX RRHs
FHDB interfaces
OPT2
OPT1
RET
ANT2 Table 447
EAC
DCIN
ANT1
FHDB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps
Antenna Line Devices (ALDs) support Table 448
FHDB ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
DN0951745 Issue: 25
© 2017 Nokia
305
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 448
FHDB ALD support (Cont.)
ALD support via antenna ports
Value
Power per port
15 W
Functional block diagram Figure 93
FHDB functional block diagram
OpticalIF RX
RXfilter
OpticalIF
VSWR
Bias-T
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 449
FHDB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
306
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 450 Mode
Descriptions of 2TX RRHs
FHDB power consumption Configu ration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power consum ption
Power consum ption
ETSI ETSI 202706 202706 average busy load hour PRRH, load PBH static RRH, static GSM
Power consum ption
Power consum ption
Power consum ption
100% RF power load P100%
Typical as 25% TCH load, 60% DTX, 4 dB PC
Busy as Max 50% load (2% TCH GoS), load, 60% 60% DTX, 4 DTX, 4 dB PC dB PC
RRH
Power consum ption
1/1/1
20
477
477
477
477
477
477
2/2/2
20
501
521
615
500
503
507
4/4/4
20
658
823
1115
658
751
779
8/8/8
15
804
1062
1401
WCDMA 1/1/1
20
333
363
426
2/2/2
20
410
462
578
3/3/3
20
490
567
736
4/4/4
20
669
783
1026
1/1/1
20+20
513
582
720
1/1/1
40+40
654
780
1044
1/1/1
60+60
830
1024
1422
GSM 2/2/2
20
633
727
948
714
874
1258
LTE
MSR
20
WCDMA 1/1/1 GSM 4/4/4
20 20
WCDMA 1/1/1
Table 451
Recommended FHDB power backoff in 256 QAM mode Single carrier
0.4
Dual carrier 0.8
Installation and mechanical specifications
DN0951745 Issue: 25
© 2017 Nokia
307
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 452
FHDB installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 453 Property Height
FHDB dimensions and weight HW version A.101 A.102
Value
Dimensions orientation
As delivered, cable tie point recessed: 335.2 mm (13.2 in.) With lower mounting bracket in the "FMFA" position: 571 mm (22.5 in.) With lower mounting bracket in the alternative "ALT" position: 621 mm (24.4 in.)
A.103
With upper and lower mounting brackets: 572.1 mm (22.5 in.) Depth
A.101
height
As delivered, cable tie point recessed: 425.8 mm (16.8 in.) width depth
324 mm (12.8 in.)
A.102
Width
A.103
287 mm (11.3 in.)
A.101
260 mm (10.2 in.)
A.102
Weight
A.103
256.7 mm (10.1 in.)
A.101
17.3 kg (38.1 lb)
A.102
Volume
A.103
16.3 kg (35.9 lb)
A.101
21 l
A.102 A.103
19.1 l
Environmental specifications
308
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 454
Descriptions of 2TX RRHs
FHDB environmental specifications Property
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s (this is valid for fanless products)
+40°C (104°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 455
FHDB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
DN0951745 Issue: 25
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible
© 2017 Nokia
No alarm
309
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 455
FHDB LEDs (Cont.) LED color
Description •
Alarm
Working normally, no alarm on the RF Module
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
11.12 Flexi RRH 2-pipe 1800 120 W (FHEG) FHEG technical specifications. Functional description Table 456
FHEG functional specification Property
310
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1850-1880 MHz
RX frequency range
1755-1785 MHz
DL instantaneous bandwidth
30 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 456
Descriptions of 2TX RRHs
FHEG functional specification (Cont.) Property
Value
UL filter bandwidth
30 MHz
Interfaces Figure 94
LED
FHEG interfaces
OPT2
RET
ANT2 Table 457
OPT1
EAC
DCIN
ANT1
FHEG interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Antenna Line Devices (ALDs) support
DN0951745 Issue: 25
© 2017 Nokia
311
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 458
FHEG ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
15 W
Functional block diagram Figure 95
FHEG functional block diagram
OpticalIF RX
RXfilter
OpticalIF
VSWR
Bias-T
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 459
FHEG electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
312
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 460 Mode
Descriptions of 2TX RRHs
FHEG power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
563
663
846
1/1/1 2T2R
40+40
718
887
1193
1/1/1 2T2R
60+60
915
1161
1619
Installation and mechanical specifications Table 461
FHEG installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 462 Property Height
FHEG dimensions and weight HW version A.101
Value
Dimensions orientation
version As delivered, cable tie point recessed: 335.2 mm (13.2 in.) With lower mounting bracket in the "FMFA" position: 571 mm (22.5 in.) With lower mounting bracket in the alternative "ALT" position: 621 mm (24.4 in.)
A.102
As delivered, cable tie point recessed: 425.8 mm (16.8 in.) With upper and lower mounting brackets: 572.1 mm (22.5 in.)
DN0951745 Issue: 25
© 2017 Nokia
height width depth
313
Descriptions of 2TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 462
FHEG dimensions and weight (Cont.)
Property Depth
Width
Weight
Volume
HW version
Value
A.101
324 mm (12.8 in.)
A.102
287 mm (11.3 in.)
A.101
260 mm (10.2 in.)
A.102
256.7 mm (10.1 in.)
A.101
17.3 kg (38.1 lb)
A.102
16.3 kg (35.9 lb)
A.101
21 l
A.102
19.1 l
Dimensions orientation
Environmental specifications Table 463
FHEG environmental specifications Property
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s (this is valid for fanless products)
+40°C (104°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 464
FHEG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
314
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 464
Descriptions of 2TX RRHs
FHEG LEDs (Cont.) LED color
Description
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
Alarm No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
315
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
12 Descriptions of 4TX RRHs 12.1 Flexi Remote Radio Head 4TX 1700/2100 (FRIG) FRIG technical specifications. Functional description Table 465
FRIG functional specification Property
Value
Output power
4x30 W 2x60 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2110-2155 MHz
RX frequency range
1710-1755 MHz
DL instantaneous bandwidth
45 MHz
UL instantaneous bandwidth
45 MHz
DL filter bandwidth
45 MHz
UL filter bandwidth
45 MHz
Interfaces Figure 96
FRIG interfaces
ANT4
EAC
ANT3
LMP
ANT2
LEDs
OPT2 OPT 3
316
RET
ANT1
© 2017 Nokia
OPT1
DCIN Ground
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 466
Descriptions of 4TX RRHs
FRIG interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
3
SFP
6 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 467
FRIG ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3: 15.5 V RET: 15.5 V
Power per port
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
317
Descriptions of 4TX RRHs
Figure 97
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRIG functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
RX filter
RXRF LNA
RXOUT
RFLoop OpticalIF TXRF
TX filter
PA
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF
RF control
LNA
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF LNA
RXOUT
TXRF
TX filter
PA
VSWR
Tx/Rx
Det
RXRF LNA
DCIN
RX filter
PSU
Electrical specifications Table 468
FRIG electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
318
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 469 Mode
Descriptions of 4TX RRHs
FRIG power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
8+8
603
629
684
1/1/1 2T2R
20+20
661
720
855
1/1/1 2T2R
30+30
661
720
855
1/1/1 2T2R
40+40
854
975
1242
1/1/1 2T2R
60+60
956
1136
1550
1/1/1 4T4R
8+8
907
967
1087
1/1/1 4T4R
15+15
986
1088
1301
1/1/1 4T4R
20+20
1037
1167
1446
1/1/1 4T4R
30+30
1201
1396
1810
Installation and mechanical specifications Table 470
FRIG installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
319
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 471
FRIG dimensions and weight Property
Value
Height
459.5 mm (18.1 in.)
Depth
2x60 W version: 133.4 mm (5.2 in.)
Dimensions orientation
4x30 W version: 162.3 mm (6.4 in.) Width
400 mm (15.7 in.) height
Weight
23.7 kg (52.5 Ib)
Volume
26 l
width depth
Environmental specifications Table 472
FRIG environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 473
FRIG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• •
320
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 473
Descriptions of 4TX RRHs
FRIG LEDs (Cont.) LED color
Description
Yellow, stable
•
Major/Critical alarm affecting a module subcomponent or antenna carrier
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
• •
Yellow, blinking
• •
Green, stable
•
•
Alarm
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
321
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
12.2 Flexi RRH 4-pipe 2100 120 W (FHGB) FHGB technical specifications. Functional description Table 474
FHGB functional specification Property
Value
Output power
4x30 W/2x60 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2110-2130 MHz
RX frequency range
1920-1940 MHz
DL instantaneous bandwidth
20 MHz
UL instantaneous bandwidth
20 MHz
DL filter bandwidth
20 MHz
UL filter bandwidth
20 MHz
Interfaces
322
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 98
FHGB interfaces
TXM4 RXM4 ANT4
EAC
Table 475
TXM3 TXM2 CUSTI/O RXM3 RXM2 ANT3 ANT2
LMP
OPT3
OPT2
TXM1 RXM1 ANT1
OPT1
RET
GND
FHGB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
N-type, female
-
RF external connector
RXM
8
QMA
-
1
8-pin circular
RS-485
TXM
Remote Electrical RET Tilt
DN0951745 Issue: 25
Descriptions of 4TX RRHs
© 2017 Nokia
323
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 475
FHGB interfaces (Cont.)
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
External Alarm Connection
EAC
1
22-pole circular
-
Optical interface
OPT
3
SFP
6 Gbps, OBSAI
Local LMP Management Port
1
2x15 pin header
-
Grounding
1
Dual M6 screws
GND
Antenna Line Devices (ALDs) support Table 476
FHGB ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3: 27 V RET: 27 V
Power per port
30 W
Functional block diagram
324
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 99
Descriptions of 4TX RRHs
FHGB functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
TXMon1 ANT 1
LNA
RFLoop TXRF
OpticalIF
RXMon1 TX filter
PA
VSWR Det
RX filter
RXRF OpticalIF
TXMon2 ANT 2
LNA
RF control
RXMon2
TXRF
TX filter
PA
Bias-T
VSWR Det
OpticalIF
RX filter
RXRF
TXMon3 ANT 3
LNA RXMon3
TXRF
TX filter
PA
VSWR Det
RXRF LNA
RX filter
TXMon4 ANT 4
RXMon4
DCIN
PSU
Electrical specifications Table 477
FHGB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
325
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 478 Mode
FHGB power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 479
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
676
744
904
1/1/1 2T2R
2x30
758
859
1098
1/1/1 2T2R
2x40
880
1010
1355
1/1/1 2T2R
2x60
990
1185
1790
1/1/1 4T4R
4x20
1055
1199
1523
1/1/1 4T4R
4x30
1222
1434
1990
Recommended FHGB power backoff in 256 QAM mode Single carrier
0.2
Installation and mechanical specifications Table 480
FHGB installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight
326
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 481
Descriptions of 4TX RRHs
FHGB dimensions and weight Property
Value
Height
Including handle and connectors: 564 mm (22.2 in.)
Depth
133 mm (5.2 in.)
Width
387 mm (15.2 in.)
Weight
max. 24 kg (52.9 Ib)
Dimensions orientation
height width
Volume
max. 27 l depth
Environmental specifications Table 482
FHGB environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-35°C (-31°F)
LEDs Table 483
FHGB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• •
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans
© 2017 Nokia
327
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 483
FHGB LEDs (Cont.) LED color
Description
Yellow, stable
•
Major/Critical alarm affecting a module subcomponent or antenna carrier
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
• •
Yellow, blinking
• •
Green, stable
•
•
Alarm
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
328
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 4TX RRHs
12.3 Flexi Remote Radio Head 4TX 2600 (FRHD) FRHD technical specifications. Functional description Table 484
FRHD functional specification Property
Value
Output power
4x30 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2640-2690 MHz
RX frequency range
2520-2570 MHz
DL instantaneous bandwidth
40 MHz
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
50 MHz
UL filter bandwidth
50 MHz
Interfaces Figure 100
FRHD interfaces
ANT4
EAC
ANT3
LMP
ANT2
LEDs
OPT2 OPT 3
DN0951745 Issue: 25
RET
ANT1
© 2017 Nokia
OPT1
DCIN Ground
329
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 485
FRHD interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
3
SFP
6 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support Table 486
FRHD ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3: 15.5 V RET: 15.5 V
Power per port
30 W
Functional block diagram
330
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 101
Descriptions of 4TX RRHs
FRHD functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
RX filter
RXRF LNA
RXOUT
RFLoop OpticalIF TXRF
TX filter
PA
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF
RF control
LNA
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF LNA
RXOUT
TXRF
TX filter
PA
VSWR
Tx/Rx
Det
RXRF LNA
DCIN
RX filter
PSU
Electrical specifications Table 487
FRHD electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
331
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 488 Mode
FRHD power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
661
744
915
1/1/1 2T2R
2x30
722
840
1095
1/1/1 4T4R
4x20
1091
1266
1623
1/1/1 4T4R
4x30
1227
1476
2019
Installation and mechanical specifications Table 489
FRHD installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 490
FRHD dimensions and weight Property
Value
Height
578 mm (22.7 in.)
Depth
201.5 mm (7.9 in.)
Width
400 mm (15.7 in.)
Weight
max. 28.5 kg (62.8 Ib)
Volume
27 l
Dimensions orientation
height width depth
332
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of 4TX RRHs
Environmental specifications Table 491
FRHD environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 492
FRHD LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
DN0951745 Issue: 25
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated
© 2017 Nokia
No alarm
333
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 492
FRHD LEDs (Cont.) LED color
Description
•
Alarm
and transmission is possible Working normally, no alarm on the RF Module
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
12.4 Flexi Remote Radio Head 4TX 2600 (FRHE) FRHE technical specifications. Functional description Table 493
FRHE functional specification Property
334
Value
Output power
4x30 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2620-2675 MHz
RX frequency range
2500-2555 MHz
DL instantaneous bandwidth
40 MHz
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 493
Descriptions of 4TX RRHs
FRHE functional specification (Cont.) Property
Value
UL instantaneous bandwidth
40 MHz
DL filter bandwidth
55 MHz
UL filter bandwidth
55 MHz
Interfaces Figure 102
FRHE interfaces
ANT4
EAC
ANT3
LMP
ANT2
LEDs
OPT2 OPT 3
Table 494
RET
ANT1
OPT1
DCIN Ground
FRHE interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
3
SFP
6 Gbps
Local LMP Management Port
1
2x15 pin header
-
Antenna Line Devices (ALDs) support
DN0951745 Issue: 25
© 2017 Nokia
335
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 495
FRHE ALD support
ALD support via antenna ports
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1, ANT3: 15.5 V RET: 14.5 V
Power per port
30 W
Functional block diagram Figure 103
FRHE functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
RX filter
RXRF LNA
RXOUT
RFLoop OpticalIF TXRF
TX filter
PA
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF
RF control
LNA
TXRF
TX filter
PA
Bias-T
VSWR
Tx/Rx
Det
OpticalIF
RX filter
RXRF LNA
RXOUT
TXRF
TX filter
PA
VSWR
Tx/Rx
Det
RXRF LNA
DCIN
RX filter
PSU
Electrical specifications Table 496
FRHE electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
336
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 497 Mode
Descriptions of 4TX RRHs
FRHE power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
661
744
915
1/1/1 2T2R
2x30
722
840
1095
1/1/1 4T4R
4x20
1091
1266
1623
1/1/1 4T4R
4x30
1227
1476
2019
Installation and mechanical specifications Table 498
FRHE installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
Dimensions and weight Table 499
FRHE dimensions and weight Property
Value
Height
578 mm (22.7 in.)
Depth
201.5 mm (7.9 in.)
Width
400 mm (15.7 in.)
Weight
max. 28.5 kg (62.8 Ib)
Volume
27 l
Dimensions orientation
height width depth
DN0951745 Issue: 25
© 2017 Nokia
337
Descriptions of 4TX RRHs
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Environmental specifications Table 500
FRHE environmental specifications Property
Value
Maximum operational outdoor temperature in the shade (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun (according to GR-487-Core specification)
+50°C (122°F)
Maximum indoor temperature (this is valid for fanless products)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 501
FRHE LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
338
Alarm
•
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 501
Descriptions of 4TX RRHs
FRHE LEDs (Cont.) LED color
Description
•
Alarm
and transmission is possible Working normally, no alarm on the RF Module
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
339
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
13 Descriptions of RRHs Rel. 4.0 13.1 Flexi RRH 2-pipe 450 80 W (FRAA) FRAA technical specifications. Functional description Table 502
FRAA functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
462.5-467.5 MHz
RX frequency range
452.5-457.5 MHz
DL instantaneous bandwidth
5 MHz
UL instantaneous bandwidth
5 MHz
DL filter bandwidth
5 MHz
UL filter bandwidth
5 MHz
Interfaces Figure 104
FRAA interfaces
OPT2 OPT1
DCIN
GND
340
ANT2
RET
EAC
© 2017 Nokia
RXO2
RXO1
ANT1
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 503
Descriptions of RRHs Rel. 4.0
FRAA interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
4.3-10
-
RF external connector
RXO
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 504
FRAA ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
40 W
Power
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
341
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 105
FRAA functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol
RXMON
RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 505
FRAA electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 506 Mode
FRAA power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
342
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1
20+20
477
553
700
1/1/1
40+40
644
792
1053
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 507
Descriptions of RRHs Rel. 4.0
Recommended FRAA power backoff in 256 QAM mode Single carrier
Dual carrier
0.6
-
Installation and mechanical specifications Table 508
FRAA installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi 4.0 Small Book Mount Kit (FMFH)
Dimensions and weight Table 509
FRAA dimensions and weight Property
Height
Value Core RRH: 371 mm (14.6 in) With upper and lower mounting brackets: 721 mm (28.4 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFH: 485 mm (19.1 in) With FMFH and strain relief bracket: 700 mm (27.5 in) Depth
Core RRH depth without plastic cover: 169 mm (6.6 in) With plastic cover and mounting brackets: 215 mm (8.5 in) With FMFH: 430 mm (16.9 in)
Width
Core RRH: 291 mm (11.5 in)
height width depth
With plastic cover and mounting brackets: 302 mm (11.9 in) With FMFH: 182 mm (7.2 in) Weight
Core RRH: 14.5 kg (32.0 lb) With plastic cover and mounting brackets: 16.2 kg (35.7 lb)
Volume
DN0951745 Issue: 25
With cover: 18 l
© 2017 Nokia
343
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 509
FRAA dimensions and weight (Cont.) Property
Value Without cover: 15 l
Dimensions orientation With FMFH and strain relief
height width depth
Environmental specifications Table 510
FRAA environmental specifications Property
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 511
FRAA LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• •
344
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 511
Descriptions of RRHs Rel. 4.0
FRAA LEDs (Cont.) LED color
Description
Yellow, stable
•
Major/Critical alarm affecting a module subcomponent or antenna carrier
•
Until software download begins The carriers are blocked from BTS There is no connection to any System Module
• •
Yellow, blinking
• •
Green, stable
•
•
Alarm
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
345
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
13.2 Flexi RRH 2-pipe 850 80 W (FRCC) FRCC technical specifications. Functional description Table 512
FRCC functional specification Property
Value
Output power
2x40 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
862.6-869 MHz
RX frequency range
817.6-824 MHz
DL instantaneous bandwidth
6.4 MHz
UL instantaneous bandwidth
6.4 MHz
DL filter bandwidth
6.4 MHz
UL filter bandwidth
6.4 MHz
Interfaces Figure 106
FRCC interfaces
RET
DCIN
OPT1 OPT2 EAC
RXO2 RXO1
GND
ANT4
346
ANT1
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 513
Descriptions of RRHs Rel. 4.0
FRCC interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT 1
2
7/16
For ANT 4, SW displays ANT 2
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
ANT 4
Antenna Line Devices (ALDs) support Table 514
FRCC ALD support
ALD support via antenna ports
Value
AISG
RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
RET: 14.5 V
Power per port
40 W
Power
30 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
347
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 107
FRCC functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
VSWR
LNA Det
TXRF
PA
TXfilter
RFcontrol
RXMON
EAC
RX
RXfilter
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 515
FRCC electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 516 Mode
FRCC power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
573
624
736
1/1/1 2T2R
40+40
746
836
1016
Installation and mechanical specifications
348
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 517
Descriptions of RRHs Rel. 4.0
FRCC installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi 4.0 Large Book Mount Kit (FMFB)
Dimensions and weight Table 518
FRCC dimensions and weight Property
Height
Value Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
width depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 22 kg (48.5 lbs) With plastic cover and mounting brackets: 24 kg (53.0 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
DN0951745 Issue: 25
© 2017 Nokia
349
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Environmental specifications Table 519
FRCC environmental specifications Property
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 520
FRCC LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
350
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 520
Descriptions of RRHs Rel. 4.0
FRCC LEDs (Cont.) LED color
Description
Green, stable
•
•
Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
Alarm No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.3 Flexi RRH 2-pipe 850 120 W (FRCG) FRCG technical specifications. Functional description Table 521
FRCG functional specification Property
DN0951745 Issue: 25
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technologies
WCDMA, FDD-LTE
TX frequency range
869-894 MHz
RX frequency range
824-849 MHz
© 2017 Nokia
351
Descriptions of RRHs Rel. 4.0
Table 521
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRCG functional specification (Cont.) Property
Value
DL instantaneous bandwidth
25 MHz
UL instantaneous bandwidth
25 MHz
DL filter bandwidth
25 MHz
UL filter bandwidth
25 MHz
Interfaces Figure 108
FRCG interfaces
OPT1 OPT2 EAC
DCIN
RET
RXO2 RXO1
GND
ANT4 Table 522
ANT1 FRCG interfaces
Interface
352
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT 1
2
4.3-10
For ANT 4, SW displays ANT 2
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
1
D-sub MDR14
-
ANT 4
EAC
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 522
Descriptions of RRHs Rel. 4.0
FRCG interfaces (Cont.)
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 523
FRCG ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
40 W
Power
30 W
Functional block diagram Figure 109
FRCG functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol
RXMON
RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 524
FRCG electrical specifications Property
DN0951745 Issue: 25
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
© 2017 Nokia
353
Descriptions of RRHs Rel. 4.0
Table 524
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRCG electrical specifications (Cont.) Property
Value
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 525 Mode
FRCG power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
Table 526
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1
20
304
336
402
2/2/2
20
391
447
564
3/3/3
20
434
511
679
1/1/1 2T2R
20+20
544
630
783
1/1/1 2T2R
40+40
656
795
1060
1/1/1 2T2R
60+60
752
937
1310
Recommended FRCG power backoff in 256 QAM mode Single carrier
0.6
Dual carrier 1
Installation and mechanical specifications Table 527
FRCG installation and mechanical specifications Property
Installation options
354
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi 4.0 Large Book Mount Kit (FMFB)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of RRHs Rel. 4.0
Dimensions and weight Table 528
FRCG dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 22 kg (48.5 lb) With plastic cover and mounting brackets: 24 kg (53.0 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 529
FRCG environmental specifications Property
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
DN0951745 Issue: 25
© 2017 Nokia
Value +55°C (131°F)
355
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 529
FRCG environmental specifications (Cont.) Property
Value
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s,valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 530
FRCG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
356
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
© 2017 Nokia
No alarm
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 530
Descriptions of RRHs Rel. 4.0
FRCG LEDs (Cont.) LED color
Description
Alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.4 Flexi RRH 2-pipe 873 120 W (FRCJ) FRCJ technical specifications. Functional description Table 531
FRCJ functional specification Property
DN0951745 Issue: 25
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
869-880 MHz
RX frequency range
824-835 MHz
DL instantaneous bandwidth
11 MHz
UL instantaneous bandwidth
11 MHz
DL filter bandwidth
11 MHz
UL filter bandwidth
11 MHz
© 2017 Nokia
357
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Interfaces Figure 110
FRCJ interfaces
DCIN
GND Table 532
ANT1 TX/RX
OPT2 OPT1
RET
ANT2 TX/RX
EAC
ANT3 RX
ANT4 RX
FRCJ interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
4.3-10
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
RJ45
-
Optical interface
OPT
2
SFP
3 Gbps to 6 Gbps, OBSAI
1
M8 or dual M5 screws
GND
Grounding
Antenna Line Devices (ALDs) support Table 533
FRCJ ALD support
ALD support via antenna ports
358
Value
AISG
RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
RET: 14.5 V
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 533
Descriptions of RRHs Rel. 4.0
FRCJ ALD support (Cont.)
ALD support via antenna ports
Value
Power per port
-
Power
60 W
Functional block diagram
DN0951745 Issue: 25
© 2017 Nokia
359
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 111
FRCJ functional block diagram
RX
OpticalIF
RXfilter
VSWR
Tx/Rx
LNA Det
TXRF
OpticalIF
PA
TXfilter
PDRX RFcontrol
RX
RXfilter
VSWR
Tx/Rx
LNA Det
TXRF
PA
TXfilter
EAC Rx
RET
RX
RXfilter LNA
Rx
RX
RXfilter LNA
DC IN
PSU
Electrical specifications
360
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 534
Descriptions of RRHs Rel. 4.0
FRCJ electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption Table 535 Mode
FRCJ power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
465
544
688
1/1/1 2T2R
40+40
649
795
1073
1/1/1 2T2R
60+60
791
1001
1416
Installation and mechanical specifications Table 536
FRCJ installation and mechanical specifications Property
Value
Installation options
•
pole/wall installation
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA)
•
Flexi Power AC/DC Submodule 230V (FPAD)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
361
Descriptions of RRHs Rel. 4.0
Table 537
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRCJ dimensions and weight Property
Value
Height
Core RRH: 315 mm (12.4 in) With plastic cover: 333 mm (13.1 in)
Dimensions orientation With plastic cover and mounting brackets
With upper and lower mounting brackets: 499 mm (19.7 in) Depth
Core RRH depth without plastic cover: 174 mm (6.8 in) With plastic cover: 186 mm (7.3 in)
Width
With plastic cover and mounting brackets: 210 mm (8.3 in)
width
Core RRH: 264 mm (10.4 in)
depth
height
With plastic cover: 302 mm (11.9 in) With plastic cover and mounting brackets: 302 mm (11.9 in) Weight
Core RRH: 14.8 kg (32.6 lb) With plastic cover: 15.5 kg (34.2 lb) With plastic cover and mounting brackets: 16.2 kg (35.7 lb)
Volume
With cover: 19 l Without cover: 12.7 l
Environmental specifications Table 538
FRCJ environmental specifications Property
362
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 538
Descriptions of RRHs Rel. 4.0
FRCJ environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 539
FRCJ LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
363
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 539
FRCJ LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The maximum startup voltage is -40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.5 Flexi RRH 2-pipe 875 120 W (FRCI) FRCI technical specifications. Functional description Table 540
FRCI functional specification Property
Value 2x53 W
Output power
2x40 W (band edge 5 MHz) MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
869-888.4 MHz
RX frequency range
824-843.4 MHz
DL instantaneous bandwidth
19.4 MHz
UL instantaneous bandwidth
19.4 MHz
DL filter bandwidth
19.4 MHz
UL filter bandwidth
19.4 MHz
Interfaces
364
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 112
Descriptions of RRHs Rel. 4.0
FRCI interfaces
OPT1 OPT2 EAC
DCIN
RET
RXO2 RXO1
GND
ANT2 Table 541
ANT1 FRCI interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT 1
2
4.3-10
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
ANT 2
Antenna Line Devices (ALDs) support Table 542
FRCI ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
RET: AISG 2.0
Legacy Siemens equipment
No
© 2017 Nokia
365
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 542
FRCI ALD support (Cont.)
ALD support via antenna ports
Value
CWA (for non-AISG installations)
No
Voltage
RET: 14.5 V
Power per port
No
Power
30 W
Functional block diagram Figure 113
FRCI functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
VSWR
LNA Det
TXRF
PA
TXfilter
RFcontrol
RXMON
EAC
RX
RXfilter
VSWR
LNA
RET
Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 543
FRCI electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
366
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 544 Mode
Descriptions of RRHs Rel. 4.0
FRCI power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 6h busy hour load) / 24h Power Power consumption consumption ETSI 102706 average PRRH, static
Power consumption
ETSI 102706 busy hour load PBH RRH,
100% RF power load P100% RRH
static
LTE
1/1/1 2T2R
20+20
449
529
670
1/1/1 2T2R
40+40
615
758
1009
1/1/1 2T2R
53+53
688
863
1211
Installation and mechanical specifications Table 545
FRCI installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
•
inside the Radio Antenna System (RAS)
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
FMFB Flexi 4.0 Large Book Mount Kit
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
367
Descriptions of RRHs Rel. 4.0
Table 546
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRCI dimensions and weight Property
Value
Height
Core RRH: 538 mm (21.2 in) With upper and lower mounting brackets: 871 mm (34.3 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 199 mm (7.8 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 293 mm (11.5 in) With plastic cover and mounting brackets: 324 mm (12.7 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 21.7 kg (47.8 lbs) With plastic cover and mounting brackets: 24 kg (53.0 lb)
Volume
With cover: 33 l Without cover: 24.9 l height width depth
Environmental specifications Table 547
FRCI environmental specifications Property
368
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 547
Descriptions of RRHs Rel. 4.0
FRCI environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 548
FRCI LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
369
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 548
FRCI LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.6 Flexi RRH 2-pipe 2100 120 W T (FRGB) FRGB technical specifications. Functional description Table 549
FRGB functional specification Property
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2110-2160 MHz
RX frequency range
1920-1970 MHz
DL instantaneous bandwidth
50 MHz
UL instantaneous bandwidth
50 MHz
DL filter bandwidth
50 MHz
UL filter bandwidth
50 MHz
Interfaces
370
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 114
FRGB interfaces
OPT2 OPT1
DCIN
GND Table 550
Descriptions of RRHs Rel. 4.0
ANT2
RET
EAC
RXO2
RXO1
ANT1
FRGB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power Connector DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
RXO
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 551
FRGB ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V
© 2017 Nokia
371
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 551
FRGB ALD support (Cont.)
ALD support via antenna ports
Value RET: 14.5 V
Power per port
40 W
Power
30 W
Functional block diagram Figure 115
FRGB functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol
RXMON
RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 552
FRGB electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
372
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 553 Mode
Descriptions of RRHs Rel. 4.0
FRGB power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 6h busy hour load) / 24h Power Power consumption consumption ETSI 102706 average PRRH, static
Power consumption
ETSI 102706 busy hour load PBH RRH,
100% RF power load P100% RRH
static
LTE
Table 554
1/1/1
20+20
467
550
732
1/1/1
40+40
659
811
1153
1/1/1
60+60
810
1037
1562
Recommended FRGB power backoff in 256 QAM mode Single carrier
0.7
Dual carrier 0.8
Installation and mechanical specifications Table 555
FRGB installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi 4.0 Small Book Mount Kit (FMFH)
Dimensions and weight
DN0951745 Issue: 25
© 2017 Nokia
373
Descriptions of RRHs Rel. 4.0
Table 556
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRGB dimensions and weight Property
Value
Height
Core RRH: 371 mm (14.6 in) With upper and lower mounting brackets: 721 mm (28.4 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFH: 485 mm (19.1 in) With FMFH and strain relief bracket: 700 mm (27.5 in) Depth
Core RRH depth without plastic cover: 169 mm (6.6 in) With plastic cover and mounting brackets: 215 mm (8.5 in)
height width
With FMFH: 430 mm (16.9 in) Width
depth
Core RRH: 291 mm (11.5 in) With plastic cover and mounting brackets: 302 mm (11.9 in)
With FMFH and strain relief
With FMFH: 182 mm (7.2 in) Weight
Core RRH: 14.5 kg (32.0 lb) With plastic cover and mounting brackets: 16.2 kg (35.7 lb)
Volume
With cover: 18 l height
Without cover: 15 l
width depth
Environmental specifications Table 557
FRGB environmental specifications Property
374
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 557
Descriptions of RRHs Rel. 4.0
FRGB environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 558
FRGB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
375
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 558
FRGB LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.7 Flexi RRH 2-pipe 2100 120 W (FRGY) FRGY technical specifications. Functional description Table 559
FRGY functional specification Property
Value
Output power
2x60 W
MIMO
2TX
Outdoor installation
Yes
SW supported technology
WCDMA, FDD-LTE
TX frequency range
2110-2170 MHz
RX frequency range
1920-1980 MHz
DL instantaneous bandwidth
60 MHz
UL instantaneous bandwidth
60 MHz
DL filter bandwidth
60 MHz
UL filter bandwidth
60 MHz
Interfaces
376
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 116
FRGY interfaces
OPT2 OPT1
DCIN
GND Table 560
Descriptions of RRHs Rel. 4.0
ANT2
RET
EAC
RXO2
RXO1
ANT1
FRGY interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
2
7/16
-
RF external connector
RXO
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT
2
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 561
FRGY ALD support
ALD support via antenna ports
DN0951745 Issue: 25
Value
AISG
ANT1, RET: AISG 2.0
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V
© 2017 Nokia
377
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 561
FRGY ALD support (Cont.)
ALD support via antenna ports
Value RET: 14.5 V
Power per port
40 W
Power
30 W
Functional block diagram Figure 117
FRGY functional block diagram
OpticalIF
RXMON
RX
RXfilter
OpticalIF
Bias-T
VSWR
LNA Det
TXRF
EAC
PA
TXfilter
RFcontrol
RXMON
RX
RXfilter
RET
VSWR
LNA Det
TXRF
DCIN
PA
TXfilter
PSU
Electrical specifications Table 562
FRGY electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
378
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 563 Mode
Descriptions of RRHs Rel. 4.0
FRGY power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
MSR
ETSI 202706 busy hour load PBH RRH, static
100% RF power load P100% RRH
1/1/1
20
324
357
452
2/2/2
20
422
482
626
3/3/3
20
486
572
788
4/4/4
20
618
744
1052
1/1/1
20+20
457
533
701
1/1/1
40+40
658
799
1126
1/1/1
60+60
800
1015
1536
623
746
1021
766.9
952.5
1386
WCDMA 2/2/2 20 LTE 1/1/1 2T2R 10 MHz
20+20
WCDMA 2/2/2 40 LTE 1/1/1 2T2R 10 MHz
Table 564
ETSI 202706 average load PRRH, static
Power consumption
20+20
Recommended FRGY power backoff in 256 QAM mode Single carrier
0.6
Dual carrier 1.3
Installation and mechanical specifications Table 565
FRGY installation and mechanical specifications Property
Installation options
DN0951745 Issue: 25
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi 4.0 Small Book Mount Kit (FMFH)
© 2017 Nokia
379
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Dimensions and weight Table 566
FRGY dimensions and weight Property
Value
Height
Core RRH: 371 mm (14.6 in) With upper and lower mounting brackets: 721 mm (28.4 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFH: 485 mm (19.1 in) With FMFH and strain relief bracket: 700 mm (27.5 in) Depth
Core RRH depth without plastic cover: 169 mm (6.6 in) With plastic cover and mounting brackets: 215 mm (8.5 in)
height width
With FMFH: 430 mm (16.9 in) Width
depth
Core RRH: 291 mm (11.5 in) With plastic cover and mounting brackets: 302 mm (11.9 in)
With FMFH and strain relief
With FMFH: 182 mm (7.2 in) Weight
Core RRH: 14.5 kg (32.0 lb) With plastic cover and mounting brackets: 16.2 kg (35.7 lb)
Volume
With cover: 18 l height
Without cover: 15 l
width depth
Environmental specifications Table 567
FRGY environmental specifications Property
380
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 567
Descriptions of RRHs Rel. 4.0
FRGY environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 568
FRGY LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
DN0951745 Issue: 25
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
381
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 568
FRGY LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.8 Flexi RRH 4-pipe 720/730 160 W (FRBG) FRBG technical specifications. Functional description Table 569
FRBG functional specification Property
Value
Output power
4x40 W (B12 or B17: 2x40 W, B29: 2x40 W)
MIMO
2TX on B12, B17 and B29
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
B12: 729-745 MHz B17: 734-745 MHz B29: 718-728 MHz
RX frequency range
B12: 699-715 MHz B17: 704-715 MHz
DL instantaneous bandwidth
B12: 16 MHz B17: 11 MHz B29: 10 MHz
UL instantaneous bandwidth
382
© 2017 Nokia
B12: 16 MHz
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 569
Descriptions of RRHs Rel. 4.0
FRBG functional specification (Cont.) Property
Value B17: 11 MHz
DL filter bandwidth
B12: 16 MHz B17: 11 MHz B29: 10 MHz
UL filter bandwidth
B12: 16 MHz B17: 11 MHz
Interfaces Figure 118
FRBG interfaces
OPT1 CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4TX B29 Table 570
ANT3TX B29
ANT1TX/RX B12/B17
FRBG interfaces
Interface
DN0951745 Issue: 25
ANT2TX/RX B12/B17
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
Rx EXT
2
QMA
-
© 2017 Nokia
383
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 570
FRBG interfaces (Cont.)
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 571
FRBG ALD support
ALD support via antenna ports
Value
AISG
ANT1, RET: AISG 2.0
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram
384
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 119
Descriptions of RRHs Rel. 4.0
FRBG functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
OpticalIF
TX filter
PA
VSWR Det
RX filter
RXRF OpticalIF
RF control
Tx/Rx ANT 2
LNA RXMON
VSWR
OpticalIF
TXRF
PA
TX filter
TXRF
PA
TX filter
Det
Tx ANT 3
VSWR
DCIN
Det
Tx ANT 4
PSU
Electrical specifications Table 572
FRBG electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
385
Descriptions of RRHs Rel. 4.0
Table 573 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRBG power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 574
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
560
630
768
1/1/1 2T2R
2x40
685
801
1092
1/1/1 4T4R
4x20
834
972
1248
1/1/1 4T4R
4x40
1090
1341
1932
Recommended FRBG power backoff in 256 QAM mode Single carrier
0.7
Dual carrier 1.2
Installation and mechanical specifications Table 575
FRBG installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
Dimensions and weight
386
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 576
Descriptions of RRHs Rel. 4.0
FRBG dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 24 kg (52.9 lb) With plastic cover and mounting brackets: 26 kg (57.3 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 577
FRBG environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at
+45°C (113°F)
© 2017 Nokia
387
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 577
FRBG environmental specifications (Cont.) Property
Value
constant high ambient temperature, maximum output power might be limited) Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 578
FRBG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
388
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 578
Descriptions of RRHs Rel. 4.0
FRBG LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.9 Flexi RRH 4-pipe 720/750 160 W (FRBE) FRBE technical specifications. Functional description Table 579
FRBE functional specification Property
Value
Output power
B13: 2x40 W, B29: 2x40 W
MIMO
2TX on B13 and B29
Outdoor installation
yes
SW supported technology
FDD-LTE
TX frequency range
B13: 746-756 MHz B29: 718-728 MHz
RX frequency range
B13: 777-787 MHz
DL instantaneous bandwidth
B13: 10 MHz B29: 10 MHz
UL instantaneous bandwidth
10 MHz
DL filter bandwidth
B13: 10 MHz B29: 10 MHz
UL filter bandwidth
10 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
389
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 120
FRBE interfaces
OPT1 CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4TX B29 Table 580
ANT3TX B29
ANT2TX/RX B13
ANT1TX/RX B13
FRBE interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
Rx EXT
2
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 581
FRBE ALD support
ALD support via antenna ports AISG
390
Value ANT1, RET: AISG 2.0
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 581
Descriptions of RRHs Rel. 4.0
FRBE ALD support (Cont.)
ALD support via antenna ports
Value
Legacy Siemens equipment
No
CWA (for non-AISG installations)
No
Voltage
ANT1: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram Figure 121
FRBE functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
OpticalIF
TX filter
PA
VSWR Det
RX filter
RXRF OpticalIF
RF control
Tx/Rx ANT 2
LNA RXMON
VSWR
OpticalIF
TXRF
PA
TX filter
PA
TX filter
Det
Tx ANT 3
VSWR
TXRF
DCIN
Det
Tx ANT 4
PSU
Electrical specifications Table 582
FRBE electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
DN0951745 Issue: 25
© 2017 Nokia
391
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Power consumption Table 583 Mode
FRBE power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 584
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
599
674
798
1/1/1 2T2R
2x40
705
823
1043
1/1/1 4T4R
4x20
853
837
1238
1/1/1 4T4R
4x40
1079
1305
1836
Recommended FRBE power backoff in 256 QAM mode Single carrier
0.7
Dual carrier 1
Installation and mechanical specifications Table 585
FRBE installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
Dimensions and weight
392
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 586
Descriptions of RRHs Rel. 4.0
FRBE dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 24 kg (52.9 lb) With plastic cover and mounting brackets: 26 kg (57.3 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 587
FRBE environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at
+45°C (113°F)
© 2017 Nokia
393
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 587
FRBE environmental specifications (Cont.) Property
Value
constant high ambient temperature, maximum output power might be limited) Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 588
FRBE LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
394
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 588
Descriptions of RRHs Rel. 4.0
FRBE LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.10 Flexi RRH 4-pipe 1800 160 W (FHED) FHED technical specifications. Functional description Table 589
FHED functional specification Property
Value
Output power
4x40 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1805-1880 MHz
RX frequency range
1710-1785 MHz
DL instantaneous bandwidth
65 MHz
UL instantaneous bandwidth
65 MHz
DL filter bandwidth
75 MHz
UL filter bandwidth
75 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
395
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 122
FHED interfaces
OPT1 RXO3 RXO4
CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4 Table 590
ANT1
ANT2
ANT3
FHED interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
4.3-10
-
RF external connector
RXO
4
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 591
FHED ALD support
ALD support via antenna ports
396
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 591
Descriptions of RRHs Rel. 4.0
FHED ALD support (Cont.)
ALD support via antenna ports
Value
Voltage
ANT1, ANT3: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram Figure 123
FHED functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
TX filter
PA
OpticalIF
VSWR Det
RX filter
RXRF
Tx/Rx ANT 2
LNA
OpticalIF
RF control
RXMON
TXRF
TX filter
PA
Bias-T
VSWR Det
OpticalIF
RX filter
RXRF
Tx/Rx ANT 3
LNA RXMON
TXRF
TX filter
PA
VSWR Det
RXRF LNA
RX filter
Tx/Rx ANT 4
RXMON
DCIN
PSU
Electrical specifications Table 592
FHED electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
397
Descriptions of RRHs Rel. 4.0
Table 593 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FHED power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Values preliminary estimated. Power Power consumption consumption
LTE
Table 594
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
627
693
836
1/1/1 2T2R
40+40
766
891
1175
1/1/1 4T4R
4x20
895
1000
1331
1/1/1 4T4R
4x40
1222
1501
2115
Recommended FHED power backoff in 256 QAM mode Single carrier
0.6
Dual carrier 0.8
Installation and mechanical specifications Table 595
FHED installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
Dimensions and weight
398
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 596
Descriptions of RRHs Rel. 4.0
FHED dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 24 kg (52.9 lb) With plastic cover and mounting brackets: 26 kg (57.3 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 597
FHED environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at
+45°C (113°F)
© 2017 Nokia
399
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 597
FHED environmental specifications (Cont.) Property
Value
constant high ambient temperature, maximum output power might be limited) Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 598
FHED LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
400
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 598
Descriptions of RRHs Rel. 4.0
FHED LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.11 Flexi RRH 4-pipe 1800 160 W (FHEH) FHEH technical specifications. Functional description Table 599
FHEH functional specification Property
Value
Output power
4x40 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
1850-1880 MHz
RX frequency range
1755-1785 MHz
DL instantaneous bandwidth
30 MHz
UL instantaneous bandwidth
30 MHz
DL filter bandwidth
30 MHz
UL filter bandwidth
30 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
401
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 124
FHEH interfaces
OPT1 RXO3 RXO4
CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4 Table 600
ANT1
ANT2
ANT3
FHEH interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
RXO
4
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 601
FHEH ALD support
ALD support via antenna ports
402
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 601
Descriptions of RRHs Rel. 4.0
FHEH ALD support (Cont.)
ALD support via antenna ports
Value
Voltage
ANT1, ANT3: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram Figure 125
FHEH functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
TX filter
PA
OpticalIF
VSWR Det
RX filter
RXRF
Tx/Rx ANT 2
LNA
OpticalIF
RF control
RXMON
TXRF
TX filter
PA
Bias-T
VSWR Det
OpticalIF
RX filter
RXRF
Tx/Rx ANT 3
LNA RXMON
TXRF
TX filter
PA
VSWR Det
RXRF LNA
RX filter
Tx/Rx ANT 4
RXMON
DCIN
PSU
Electrical specifications Table 602
FHEH electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
403
Descriptions of RRHs Rel. 4.0
Table 603 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FHEH power consumption Configuration
Output power per carrier [W]
Estimated power consumption [W] at 48VDC input at 25°C. Non-committed estimated values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Values preliminary estimated. Power Power consumption consumption
LTE
Table 604
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
20+20
615
679
766
1/1/1 2T2R
40+40
758
897
1172
1/1/1 4T4R
4x20
895
1043
1338
1/1/1 4T4R
4x40
1264
1574
2018
Recommended FHEH power backoff in 256 QAM mode Single carrier
0.6
Dual carrier 1.2
Installation and mechanical specifications Table 605
FHEH installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
Dimensions and weight
404
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 606
Descriptions of RRHs Rel. 4.0
FHEH dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 24 kg (52.9 lb) With plastic cover and mounting brackets: 26 kg (57.3 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 607
FHEH environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at
+45°C (113°F)
© 2017 Nokia
405
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 607
FHEH environmental specifications (Cont.) Property
Value
constant high ambient temperature, maximum output power might be limited) Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 608
FHEH LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
406
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 608
Descriptions of RRHs Rel. 4.0
FHEH LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.12 Flexi RRH 4-pipe 1900 160 W (FHFB) FHFB technical specifications. Functional description Table 609
FHFB functional specification Property
Value
Output power
4x40 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
WCDMA, FDD-LTE
TX frequency range
1930-1995 MHz
RX frequency range
1850-1915 MHz
DL instantaneous bandwidth
65 MHz
UL instantaneous bandwidth
65 MHz
DL filter bandwidth
65 MHz
UL filter bandwidth
65 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
407
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 126
FHFB interfaces
OPT1 RXO3 RXO4
CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4 Table 610
ANT1
ANT2
ANT3
FHFB interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
7/16
-
RF external connector
RXO
4
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 611
FHFB ALD support
ALD support via antenna ports
408
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 611
Descriptions of RRHs Rel. 4.0
FHFB ALD support (Cont.)
ALD support via antenna ports
Value
Voltage
ANT1, ANT3: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram Figure 127
FHFB functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
TX filter
PA
OpticalIF
VSWR Det
RX filter
RXRF
Tx/Rx ANT 2
LNA
OpticalIF
RF control
RXMON
TXRF
TX filter
PA
Bias-T
VSWR Det
OpticalIF
RX filter
RXRF
Tx/Rx ANT 3
LNA RXMON
TXRF
TX filter
PA
VSWR Det
RXRF LNA
RX filter
Tx/Rx ANT 4
RXMON
DCIN
PSU
Electrical specifications Table 612
FHFB electrical specifications Property
Value
Nominal supply voltage
-48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
409
Descriptions of RRHs Rel. 4.0
Table 613 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FHFB power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
WCDMA
LTE
MSR
ETSI 202706 busy hour load PBH RRH, static
100% RF power load P100% RRH
1/1/1
20
507
537
611
2/2/2
20
590
646
782
3/3/3
20
715
803
1016
4/4/4
20
800
915
1196
1/1/1 4T4R
4x20
891
1037
1357
1/1/1 4T4R
4x40
1229
1500
2088
871
992
1275
1103
1287
1696
WCDMA 2/2/2 20 (VAM) LTE 1/1/1 4T4R 10 MHz
4x10
WCDMA 2/2/2 20 (VAM) LTE 1/1/1 4T4R 10 MHz
Table 614
ETSI 202706 average load PRRH, static
Power consumption
4x20
Recommended FHFB power backoff in 256 QAM mode Single carrier
0.7
Dual carrier 0.8
Installation and mechanical specifications Table 615
FHFB installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
410
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Descriptions of RRHs Rel. 4.0
Dimensions and weight Table 616
FHFB dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 434 mm (17.1 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 169 mm (6.6 in) Weight
Core RRH: 23 kg (50.7 lb) With plastic cover and mounting brackets: 25 kg (55.1 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 617
FHFB environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
© 2017 Nokia
411
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 617
FHFB environmental specifications (Cont.) Property
Value
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at constant high ambient temperature, maximum output power might be limited)
+45°C (113°F)
Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 618
FHFB LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
412
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 618
Descriptions of RRHs Rel. 4.0
FHFB LEDs (Cont.) LED color
Description
Alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
13.13 Flexi RRH 4-pipe 2600 160 W (FRHG) FRHG technical specifications. Functional description Table 619
FRHG functional specification Property
Value
Output power
4x40 W
MIMO
4TX
Outdoor installation
Yes
SW supported technology
FDD-LTE
TX frequency range
2620-2690 MHz
RX frequency range
2500-2570 MHz
DL instantaneous bandwidth
65 MHz
UL instantaneous bandwidth
65 MHz
DL filter bandwidth
70 MHz
UL filter bandwidth
70 MHz
Interfaces
DN0951745 Issue: 25
© 2017 Nokia
413
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Figure 128
FRHG interfaces
OPT1 RXO3 RXO4
CHAIN/EXT RET
DCIN
OPT2 EAC
RXO2 RXO1
GND
ANT4 Table 620
ANT1
ANT2
ANT3
FRHG interfaces
Interface
Label on the HW
Number of interfaces
Connector type
Additional info
Power connector
DC IN
1
3-pole screw terminal
-
Antenna connector
ANT
4
4.3-10
-
RF external connector
RXO
4
QMA
-
Remote Electrical RET Tilt
1
8-pin circular
-
External Alarm Connection
EAC
1
D-sub MDR14
-
Optical interface
OPT1, OPT2, CHAIN/EXT
3
SFP
6 Gbps, OBSAI
Grounding
Ground symbol
1
M8 or dual M5 screws
GND
Antenna Line Devices (ALDs) support Table 621
FRHG ALD support
ALD support via antenna ports
414
Value
AISG
ANT1, ANT3, RET: AISG 2.0
CWA (for non-AISG installations)
No
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 621
Descriptions of RRHs Rel. 4.0
FRHG ALD support (Cont.)
ALD support via antenna ports
Value
Voltage
ANT1, ANT3: 14.5 V RET: 14.5 V
Power per port
40 W
Power
60 W
Functional block diagram Figure 129
FRHG functional block diagram DuplexFilter
RRH
TXRF
TX filter
PA
Bias-T
VSWR Det
RX filter
RXRF
Tx/Rx ANT 1
LNA RXMON
TXRF
TX filter
PA
OpticalIF
VSWR Det
RX filter
RXRF
Tx/Rx ANT 2
LNA
OpticalIF
RF control
RXMON
TXRF
TX filter
PA
Bias-T
VSWR Det
OpticalIF
RX filter
RXRF
Tx/Rx ANT 3
LNA RXMON
TXRF
TX filter
PA
VSWR Det
RXRF LNA
RX filter
Tx/Rx ANT 4
RXMON
DCIN
PSU
Electrical specifications Table 622
FRHG electrical specifications Property
Value
Nominal supply voltage
48.0 V DC
Nominal input voltage range
-40.5 V DC to -57.0 V DC
Extended input voltage range
-36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC
Power consumption
DN0951745 Issue: 25
© 2017 Nokia
415
Descriptions of RRHs Rel. 4.0
Table 623 Mode
Flexi Multiradio BTS RF Module and Remote Radio Head Description
FRHG power consumption Configuration Output power Estimated power consumption [W] at 48VDC per carrier input at 25°C. Non-committed estimated [W] values depend on the final product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power consumption consumption
LTE
Table 624
ETSI 202706 average load PRRH, static
ETSI 202706 busy hour load PBH RRH, static
Power consumption 100% RF power load P100% RRH
1/1/1 2T2R
2x20
626
712
884
1/1/1 2T2R
2x40
732
898
1216
1/1/1 4T4R
4x20
942
1117
1466
1/1/1 4T4R
4x40
1160
1431
2141
Recommended FRHG power backoff in 256 QAM mode Single carrier
0.7
Dual carrier 0.9
Installation and mechanical specifications Table 625
FRHG installation and mechanical specifications Property
Installation options
Value •
pole/wall installation
•
directly on the wall installation
•
vertical book mount
IP rating
IP65
Related optional items
•
Flexi Pole Mounting Kit (FPKA/C)
•
Flexi Power AC/DC Submodule 230V (FPAE) Flexi 4.0 Large Book Mount Kit (FMFB)
•
Dimensions and weight
416
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 626
Descriptions of RRHs Rel. 4.0
FRHG dimensions and weight Property
Value
Height
Core RRH: 583 mm (23.0 in) With upper and lower mounting brackets: 888 mm (35.0 in)
Dimensions orientation With plastic cover and mounting brackets
With FMFB: 585 mm (23.0 in) With FMFB and strain relief bracket: 790 mm (31.1 in) Depth
Core RRH: 158 mm (6.2 in) With plastic cover and mounting brackets: 200 mm (7.9 in) height
With FMFB: 169 mm (6.6 in) Width
width
Core RRH: 320 mm (12.6 in) With plastic cover and mounting brackets: 331 mm (13.0 in)
depth
With FMFB and strain relief
With FMFB: 434 mm (17.1 in) Weight
Core RRH: 24 kg (52.9 lb) With plastic cover and mounting brackets: 26 kg (57.3 lb)
Volume
With cover: 33 l Without cover: 27 l height width depth
Environmental specifications Table 627
FRHG environmental specifications Property
DN0951745 Issue: 25
Value
Maximum operational outdoor temperature in the shade, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+55°C (131°F)
Maximum operational outdoor temperature in the sun, assuming wind speed is 3 m/s (at constant high ambient temperature, maximum output power might be limited)
+50°C (122°F)
Maximum indoor temperature, assuming wind speed is 0 m/s, valid for fanless products (at
+45°C (113°F)
© 2017 Nokia
417
Descriptions of RRHs Rel. 4.0
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 627
FRHG environmental specifications (Cont.) Property
Value
constant high ambient temperature, maximum output power might be limited) Minimum operational temperature (including cold start)
-40°C (-40°F)
LEDs Table 628
FRHG LEDs LED color
Description
Red, stable
Critical alarm affecting the whole RF module or all antenna carriers
Fault
Red, blinking
Operation degraded
Major/critical alarm
• • •
Yellow, stable
• • •
Yellow, blinking
• •
Green, stable
•
•
418
Alarm
Major alarm affecting the whole RF Module Critical alarm affecting fans Major/Critical alarm affecting a module subcomponent or antenna carrier Until software download begins The carriers are blocked from BTS There is no connection to any System Module
No alarm
Software download in No alarm progress Configuration in progress: RF resources are being setup, but not yet activated Software configuration is complete or supervisory: RF resources activated and transmission is possible Working normally, no alarm on the RF Module
No alarm
Green, blinking
Software downloading and updating
No alarm
Stable Red for less than 5 seconds and changes to Stable Yellow
Switched ON, but the next conditions are not reached yet
No alarm
Stable Red for less than 5 seconds
The module is in the process of resetting
No alarm
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
Table 628
Descriptions of RRHs Rel. 4.0
FRHG LEDs (Cont.) LED color
Description
Alarm
Periodic Red and Green
Antenna line faulty/degraded Alarm due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded)
Blinking Colors (Red, Yellow, and Green), each color stable for 0.5 second
Module highlighting (Flexi BTS SM functionality that can help identifying faulty module)
No alarm
Warnings, cautions or notes related to the product
w
NOTICE: The RRH should always be mounted in a vertical orientation with connectors on the bottom side to ensure proper cooling.
g
Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down.
DN0951745 Issue: 25
© 2017 Nokia
419
Compliance with EMC, RF and safety
Flexi Multiradio BTS RF Module and Remote Radio Head Description
14 Compliance with EMC, RF and safety EMC mission, EMC immunity, RF, and safety standards for Flexi BTS. In Europe, this means compliance with Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC Text with EEA relevance. In other market areas additional compliance is fulfilled according to relevant authority requirements. EMC emission •
Common: –
–
– – –
•
MSR: –
•
–
420
ETSI EN 301 489-8: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic compatibility (EMC) standard for radio equipment services; Part 8: Specific conditions for GSM base stations
WCDMA: –
•
3GPP TS 37.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station (BS) Electromagnetic Compatibility (EMC)
GSM/EDGE: –
•
ETSI EN 301 489-1: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements ETSI EN 301 489-50: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 50: Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment EN 55022: Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement ICES-003: Information Technology Equipment (ITE) – Limits and Methods of Measurement FCC Code of Federal Regulations (CFR) 47, Part 15 Radio Frequency Devices
3GPP TS 25.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Networks; Base station and Repeater electromagnetic compatibility (EMC) ETSI EN 301 489-23: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 23: Specific conditions for IMT-2000 CDMA, Direct Spread (UTRA and E-UTRA) Base Station (BS) radio, repeater and ancillary equipment
LTE:
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
–
Compliance with EMC, RF and safety
3GPP TS 36.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Networks; Evolved Universal Terrestrial Radio Access (EUTRA); Base Station (BS) and Repeater electromagnetic compatibility (EMC)
EMC immunity •
Common: –
–
–
–
•
MSR: –
•
ETSI EN 301 489-8: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic compatibility (EMC) standard for radio equipment services; Part 8: Specific conditions for GSM base stations
WCDMA: –
–
•
3GPP TS 37.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station (BS) Electromagnetic Compatibility (EMC)
GSM/EDGE: –
•
ETSI EN 301 489-1: Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements ETSI EN 301 489-50: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 50: Specific conditions for Cellular Communication Base Station (BS), repeater and ancillary equipment IEC 61000-4-8/EN 61000-4-8: Electromagnetic compatibility (EMC) – Part 4-8: Testing and measurement techniques – Power frequency magnetic field immunity test IEC 61000-4-9 / EN 61000-4-9: Electromagnetic compatibility (EMC). Part 4-9: Testing and measurement techniques. Pulse magnetic field immunity test
ETSI EN 301 489-23: Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 23: Specific conditions for IMT-2000 CDMA, Direct Spread (UTRA and E-UTRA) Base Station (BS) radio, repeater and ancillary equipment 3GPP TS 25.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; Base Station (BS) and repeater Electromagnetic Compatibility (EMC)
LTE: –
3GPP TS 36.113: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; Evolved Universal Terrestrial Radio Access (EUTRA); Base Station (BS) and Repeater electromagnetic compatibility (EMC)
RF •
DN0951745 Issue: 25
Common:
© 2017 Nokia
421
Compliance with EMC, RF and safety
–
– – – – –
– – – – – – – –
•
–
–
422
ETSI EN 301 908-18: IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS) 3GPP TS 37.141: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station (BS) conformance testing
GSM/EDGE: –
•
ETSI EN 301 908-1: IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements FCC Code of Federal Regulations (CFR) 47, Part 2: Frequency Allocations and Radio Treaty Matters; General Rules and Regulations FCC Code of Federal Regulations (CFR) 47, Part 22: Public mobile Services (2110-2130MHz and 2160-2180MHz) FCC Code of Federal Regulations (CFR) 47, Part 24: Personal Communication Services FCC Code of Federal Regulations (CFR) 47, Part 25: Satellite Communications FCC Code of Federal Regulations (CFR) 47, Part 27: Miscellaneous Wireless Communications Services (758-763MHz and 788-793MHz) (1710-1755MHz and 2110-2155MHz) FCC Code of Federal Regulations (CFR) 47, Part 90: Private Land Mobile Radio Services RSS-Gen: General Requirements and Information for the Certification of Radio Apparaturs RSS-130: Mobile Broadband Services (MBS) Equipment Operating in the Frequency Bands 698-756 MHz and 777-787 MHz RSS-132: Cellular Telephones Employing New Technologies Operating in the Bands 824-849 MHz and 869-894 MHz RSS-133: 2GHz Personal Communications Services RSS-139: Advanced Wireless Services Equipment Operating in the Bands 17101755 MHz and 2110-2155 MHz RSS-195: Wireless Communication Service (WCS) Equipment Operating in the Bands 2305-2320 MHz and 2345-2360 MHz RSS-199: Broadband Radio Service (BRS) Equipment Operating in the Band 2500-2690
MSR: –
•
Flexi Multiradio BTS RF Module and Remote Radio Head Description
ETSI EN 301 502: Global System for Mobile communications (GSM); Harmonized EN for Base Station Equipment covering the essential requirements of article 3.2 of the R&TTE Directive 3GPP TS 51.021: 3rd Generation Partnership Project; Technical Specification Group GSM/EDGE Radio Access Network; Base Station System (BSS) equipment specification; Radio aspects
WCDMA:
© 2017 Nokia
DN0951745 Issue: 25
Flexi Multiradio BTS RF Module and Remote Radio Head Description
–
– –
•
Compliance with EMC, RF and safety
ETSI EN 301 908-3: IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS) 3GPP TS 25.141: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; Base Station (BS) conformance testing (FDD) Telec-T112
LTE: –
–
– – –
ETSI EN 301 908-14: IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS) 3GPP TS 36.141: 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; Evolved Universal Terrestrial Radio Access (EUTRA); Base Station (BS) conformance testing Telec-T139 Telec-T146 Telec-T156
Safety •
•
•
• • •
DN0951745 Issue: 25
EN 50383: Basic Standards for the calculation and measurement of the electromagnetic field strength and SAR related to human exposure from radio base stations and fixed terminal stations for wireless telecommunications system (110 MHz - 40 GHz) EN 50384: Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunications systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110 MHz - 40 GHz) - Occupational EN 50385: Product standard to demonstrate the compliances of radio base stations and fixed terminal stations for wireless telecommunications systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110 MHz - 40 GHz) - General public EN 60215: Safety requirements for radio transmitting equipment IEC 60950-1/EN 60950-1/UL 60950-1/CSA C22.2 No. 60950-1: Information technology equipment - Safety - Part 1: General requirements IEC 60950-22/EN 60950-22: Information technology equipment - Safety - Part 22: Equipment installed outdoor
© 2017 Nokia
423
Avoiding Passive Intermodulation during RF Module and RRH operation
Flexi Multiradio BTS RF Module and Remote Radio Head Description
15 Avoiding Passive Intermodulation during RF Module and RRH operation In wideband frequencies when several transmitting and receiving signals are sharing same hardware there could be noted effect called Passive Intermodulation (PIM) Interference. Using RF Modules might cause a potential risk of generating third-order intermodulation that results in distortions in own receiver (RX) channel. Antenna Line Devices (ALD) have important role in preventing Passive Intermodulation generation, even if used RF Module and RRH performance at the antenna connector complies with 3GPP requirements. Poor PIM performance of ALD might degrade significantly the reference sensitivity. ALDs, like MHAs, provided by Nokia have high PIM requirements. The risk might be high in the following cases: • •
•
maximum bandwidth (BW) used for the carriers is more than 0.5 x duplex separation of the band carriers in configuration are wideband in nature (for example WCDMA or LTE), or combination of wideband and narrow band carriers (for example RF sharing GSMWCDMA or GSM-LTE). antenna line PIM performance is poor, or not on the required level for the configuration.
Table 629
Typical reference sensitivity degradation with different Antenna line PIM performance.
PIM performance
Typical degradation
Note
-140 dBc @ 2x43 dBm
~10 dB
High degradation, carrier configuration unusable in many cases
-153 dBc @ 2x43 dBm
~2 dB
Modest degradation, tolerable in many cases
-161 dBc @ 2x43 dBm
~0.2 dB
Minimal degradation, however, difficult to reach on the typical site environment.
When using wideband carrier configurations where PIM products fall into own receiver band, it is recommended that antenna line PIM performance is at least -153 dBc measured with 2 x 43dB test signals. However, this kind of performance might be very difficult to achieve and maintain over time in outdoor environment due to mechanisms behind the PIM including corrosion, oxidation, material imperfections, and defects in workmanship. Some of these parameters might change, and can degrade performance during operation. Taking that into consideration, it is highly recommended not to use carrier configurations which are generating intermodulation results in landing in own receiver channels.
424
© 2017 Nokia
DN0951745 Issue: 25