PAPER COMPARING BASIC REQUIREMENTS IN ASME UHX SEVTION VIII AND TEMA
Full description
Description complète
PSV Connection in Caesar IIDescripción completa
Fatigue Analysis in Caesar IIFull description
Description : FRP Analysis in Caesar-II
FRP Analysis in Caesar-II
Fatigue Analysis in Caesar IIFull description
Training
Descripción: Caesar II mainly used for pipe stress analysis and water hammer is one of the frequent cases to be analysed as per this document
Description complète
Full description
Flange Leakage checking in Caesar II using ASME Section VIII method •
•
•
After performing static analysis click the “Analysis” and then click “Flanges” in CAESAR II as shown below.
ro!ide a "le name and select the proper Flange #ype in the section as mentioned in the $S. Inp%t the &ange parameters as shown below'
ress the key “Ctrl(F” to select the concerning Si)e and Rating. Few data will a%tomatically "lled from Caesar II database. *owe!er it is good practise to con"rm the data from go!erning code.
•
•
•
•
•
Flange Class is the &ange press%re rating and is re+%ired for checking ,# Rating of E+%i!alent ress%re. Flange -rade' Select $aterial -ro%p o. as per AS$E / 01.2 #able 0A list of material speci"cation. Following table can be %sed as reference'
Refer to the applicable &ange code AS$E 01.2 or AS$E / 01.34 and %pdate a%tomatically "lled &ange data. #ake special care while inp%ting for 5Small End *%b #hickness67 58arge End *%b #hickness6. 5Small End *%b #hickness 6 m%st be e+%al to the ipe #hickness. 8arge End *%b #hickness m%st be e+%al to 9:,/; where : is *%b ,tf; where > is length thro%gh *%b and tf is &ange thickness. ow it is the t%rn to enter the /olts and gasket parameters. #ake parameters from AS$E / 01.?@ or AS$E / 01.?0 as shown below'
•
•
Check /olt Circle
For Eecti!e -asket $od%l%s press Shift(D ey and then follow “*igh End” in *elp statement. 8eak ress%re Ratio m -asket Seating Stress y shall be in accordance with AS$E SEC#I GIII
•
For %bbin Hidth in the right side 8ea!e blank for Helding eck #ype and inp%t Ring Boint width as per the ring no. as described on AS$E / 01.?@ #able #>E R RI- -ASE#
•
•
•
ow inp%t the material data as shown below'
Select the material of Flange and bolt and Inp%t design temperat%re. Flange Allowable 7 /olt Allowable at design and ambient temp can be taken from CAESAR II database for partic%lar &ange and bolt material.
Flange $od%l%s of Elasticity shall be taken from table C,1 of AS$E /, 0..which is gi!en in millions of psi con!ert it to consistent %nit •
•
Kse 0.@ for Flange Allowable Stress $%ltiplier and ?.@ for /olt Allowable Stress $%ltiplier. Kse proBect speci"c data if a!ailable. ow Inp%t
•
ow r%n the analysis to st%dy the o%tp%t res%lts. ormally If safety Factor is less than one then Boint fail%re is predicted and in o%tp%t this is shown by a M mark.
•
If res%lt shows fail%re then try to red%ce the bending moment or aLial force and reanalyse. If that is not possible check if the &ange rating can be increased.