FiberHome+Wview+Network+Management+System+User+Manual

FiberHome WviewNetwork Management System User Manual

Manual Version：V1.0 Publish Date：2012.07

Wuhan FiberHome Networks Co.,Ltd provides comprehensive technical pre-sale supports and after-sale services. Any individual who has queries about products, or any impersonal enterprise who has willing to know further information about FiberHome Networks, is able to contact with our headquarters, representative offices, agencies and customer service centers by any of the contacts we are listing below: WEBSITE:

http://www.fhn.com.cn

PHONE:

0086-4008812350 0086-027-87693390 0086-027-87693391

FAX:

0086-027-87693257, 0086-027-87691520

ADDRESS:

Optical Communication Building, 5# Dongxin Rd., EastLake New-Technology Development Zone Wuhan, Hubei Province P.R.China

POST CODE:

430074

E-MAIL:

[email protected]

We appreciate your purchasing and experiencing products from us and it is our everlasting pursuit to ensure consumer satisfaction.

Copyright ©2012 by Wuhan FiberHome Networks Co.,Ltd. All Rights Reserved Copyright ownership belongs to Wuhan FiberHome Networks Co.,Ltd. Any part of this manual shall not be copied, referenced, reproduced, modified, spread, translated or used in other ways without permission. Otherwise Wuhan FiberHome Networks Co.,Ltd will reserve the right to pursue legal responsibilities.

Preface

Preface Manual Instruction This manual introduces the installation, using method of FiberHome Wview Network Management System with version 3.7 of Fiberhome Network Company. It provides simple introduction of product, including the system characteristics and the network management protocol used by this system. It provides system requirements and installation instructions of the product, including the software and hardware platform needed, the installation process and software using descriptions. It provides user interface description and the specific help operation, including basic operation, function configuration and fault management and etc.

Intended Audience The manual is intended for the following readers: 

Network engineers



Network administrators



Customers who are familiar with network fundamentals

Content Introduction Describe general substance of the manual and introduce main contents for each chapter, by cross-reference links listing for a quick search and purposive utilization. Chapter Name

Summary

Chapter1 Introduction

This chapter mainly introduces FiberHome Wview NMS. This chapter mainly introduces hardware platform and

Chapter2

System

Requirement

and

Installation Guide

specific configuration requirements of FiberHome Wview NMS, system running environment, and installation, startup and unloading method.

Chapter3

Main

Interface

Function

This chapter mainly introduces all function and description of

Introduction

FiberHome Wview NMS menu.

Chapter4 Network Element Management

This chapter mainly introduces each device name of the

Module Introduction

system and all icon in every state of the device.

FiberHome Wview Network Management System User Manual

i

Preface

Release Update Instruction Software Version

Manual Release

V3.7.2

Update Description

V1.0

First publishment.

Manual Convention Introduce general format, symbol convention, keyboard/mouse operation and safety signs. 1.

General Format Typeface

Description

Arial

Standard font for manual text, including Arabic numerals.

Bold

names, check boxes, drop-down lists, dialog box names,

Chapter/Section names menus, menu options, radio button window names. Input fields, references to other guides/manuals and

Italics

documents.

“Quotes”

Links on screens.

2． Symbol Convention Typeface

<> [

]

{

} →

Description Keyboard typing names, button names, input contents from a certain terminal. Optional

parameters,

menu

bars,

datasheets,

fragments/octets. Mandatory parameters Separator of multi-menus/paths, e.g., “Main menu → Sub-menu → Root menu”

3． Keyboard Operation Convention Operation

Description Indicates Keyboard typing names or button names. E.g.,＜Enter＞, ＜Tab＞, ＜Backspace

Characters with angle brackets

＞ , ＜ a ＞ are respectively indicating keyboard enter, tab, backspace and lowercase character “a”.


ii

Preface Operation

Description

＜Keyboard 1+Keyboard 2＞

E.g.,＜Ctrl+Alt+A＞ indicates to press “Ctrl”、

Indicates press 2 or more keys at the same time. “Alt”、“A” at the same time. Indicates press key 1 first, release and then ＜Keyboard 1, Keyboard 2＞

press key 2.. E.g.,＜Alt，F＞ indicates to press “Alt” first , then release and finally press “F”.

4． Mouse Operation Convention Operation Click Double-click Right-click Drag

Description Refers to clicking the primary mouse button (usually the left mouse button) once. Refers to quickly clicking the primary mouse button (usually the left mouse button) twice. Refers to clicking the secondary mouse button (usually the right mouse button) once. Refers to pressing and holding a mouse button and moving the mouse.

5． Safety Signs This manual utilizes general 5 safety signs to emphasis significances during operation, installation or maintenance. Operation

Description Indicates helpful information that if ignored could result in

Notice

equipment damage or interruption of services. Indicates places the manual intents to impart that the user is required to focus or pay attention to, during operation,

Attention

installation or maintenance. Indicates and imminently hazardous situation, which, if not avoided, will result in death or serous injury. This signal word

Danger

should be limited to only extreme situations. Indicates a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury. It may also

Caution

be used to alert against unsafe practices. Indicates a hazardous situation, which, if not avoided, could

Warning

result in death of serious injury, e.g., a risk of electric shock.


iii

Preface

Legal Disclaimer All the contents in this manual are based on current product information and should they have any changes, please understand that they are subject to change without notice. Fiber Home Networks Wuhan Co., Ltd commits itself to ensure accuracy, fidelity and reliability to the manual contents, however does not take any legal responsibility of any loss or damage caused by possible pretermission, inaccuracy or error in this manual.


iv

Table of Contents

Table of Contents Chapter1 Introduction .............................................................................................................. 1-1 1.1 Overview .......................................................................................................................... 1-1 1.2 Product Introduction ......................................................................................................... 1-1 Chapter2 System Requirement and Installation Guide ......................................................... 2-1 2.1 Overview .......................................................................................................................... 2-1 2.2 Hardware Platform and Software Environment ................................................................ 2-1 2.2.1 Hardware Platform............................................................................................... 2-1 2.2.2 Software Environment ......................................................................................... 2-2 2.3 Software Installation and Uninstallation Instructions ........................................................ 2-2 2.3.1 Install Client ......................................................................................................... 2-3 2.3.2 Install Server........................................................................................................ 2-6 2.3.3 Install Server and Client .................................................................................... 2-10 2.3.4 Uninstall Introduction ......................................................................................... 2-15 2.4 Software Using Instruction ............................................................................................. 2-15 2.4.1 Start Server ....................................................................................................... 2-15 2.4.2 Start Client ......................................................................................................... 2-17 2.4.3 Exit Client .......................................................................................................... 2-18 2.4.4 Stop Server........................................................................................................ 2-19 2.4.5 User Registering ................................................................................................ 2-19 2.4.6 Operation Introduction ....................................................................................... 2-21 Chapter3 Main Interface Function Introduction ..................................................................... 3-1 3.1 Overview .......................................................................................................................... 3-1 3.2 System Menu ................................................................................................................... 3-1 3.2.1 Switch User ......................................................................................................... 3-2


v

Preface

3.2.2 Security Management.......................................................................................... 3-3 3.2.3 Modify User Password....................................................................................... 3-16 3.2.4 Export Registration Information ......................................................................... 3-17 3.2.5 Import Registration Information ......................................................................... 3-18 3.2.6 Lock System ...................................................................................................... 3-19 3.2.7 Exit System ....................................................................................................... 3-20 3.3 Topology ........................................................................................................................ 3-20 3.3.1 Network View..................................................................................................... 3-21 3.3.2 Topology Thumbnail .......................................................................................... 3-25 3.3.3 Search Topology Node ...................................................................................... 3-26 3.3.4 Search Network Device ..................................................................................... 3-28 3.3.5 Export Topology Site Information ....................................................................... 3-30 3.3.6 Import Topology Site Information ....................................................................... 3-32 3.3.7 Equipment ......................................................................................................... 3-34 3.3.8 Viewgraph ......................................................................................................... 3-35 3.3.9 Unselected Nodes ............................................................................................. 3-38 3.3.10 Toolbar ............................................................................................................. 3-39 3.4 Trap Management .......................................................................................................... 3-47 3.4.1 Trap Log ............................................................................................................ 3-47 3.4.2 Trap Configuration ............................................................................................. 3-48 3.4.3 Trap Filtering or Shield ...................................................................................... 3-67 3.4.4 Troubleshooting ................................................................................................. 3-76 3.5 Prompt Column .............................................................................................................. 3-82 3.5.1 Trap Prompt Column ......................................................................................... 3-83 3.5.2 Event Prompt Column ....................................................................................... 3-84 3.5.3 Event Prompt Synchronization .......................................................................... 3-85 FiberHome Wview Network Management System User Manual

vi

Preface

3.6 Log ................................................................................................................................. 3-85 3.6.1 Security Log ...................................................................................................... 3-86 3.6.2 Operation Log .................................................................................................... 3-88 3.6.3 Event Log .......................................................................................................... 3-91 3.6.4 Performance Log ............................................................................................... 3-94 3.6.5 Log Backup ....................................................................................................... 3-97 3.7 Performance .................................................................................................................. 3-98 3.7.1 Device Performance .......................................................................................... 3-99 3.7.2 Interface Performance ..................................................................................... 3-121 3.8 Configuration ............................................................................................................... 3-137 3.8.1 Customer Management ................................................................................... 3-138 3.8.2 FTP Server Configuration ................................................................................ 3-139 3.8.3 Config Topology Link ....................................................................................... 3-140 3.8.4 Config Topology Node ..................................................................................... 3-141 3.8.5 Config Locking Interval .................................................................................... 3-142 3.8.6 System Configuration ...................................................................................... 3-143 3.9 Tool .............................................................................................................................. 3-166 3.9.1 Ping ................................................................................................................. 3-167 3.9.2 Telnet ............................................................................................................... 3-168 3.9.3 MIB Tool .......................................................................................................... 3-169 3.9.4 File Export and Conversion ............................................................................. 3-170 3.10 Report ........................................................................................................................ 3-172 3.10.1 Trap Report ................................................................................................... 3-173 3.10.2 Device Report ................................................................................................ 3-173 3.10.3 Report Generating ......................................................................................... 3-174


vii

Preface

3.11 Service ....................................................................................................................... 3-175 3.11.1 Service Type Management ............................................................................ 3-176 3.11.2 Customer Management ................................................................................. 3-177 3.11.3 Contact Management .................................................................................... 3-178 3.11.4 Region Management ..................................................................................... 3-180 3.11.5 Service Trap Management ............................................................................. 3-181 3.12 Help ........................................................................................................................... 3-182 3.12.1 Help Theme ................................................................................................... 3-182 3.12.2 About Information .......................................................................................... 3-183 Chapter4 Network Element Management

Module Introduction ......................................... 4-1

4.1 Overview .......................................................................................................................... 4-1 4.2 Device Legend Introduction ............................................................................................. 4-1


viii

Chapter1 Introduction

Chapter1 Introduction 1.1 Overview This chapter includes the following topics: Content

Page

1.1 Overview

1-1

1.2 Product Introduction

1-1

1.2 Product Introduction FiberHome Wview Network Management System is an integrated Management System of network element-level. It uses modular design. It consists of a number of different functional modules. It can manage series devices of Fiberhome Network Company. FiberHome Wview Network Management System has the following prominent characteristic: 

The management

platform

and interface are completely unified.

The

management information and management object of different device can be packaged into the form of software package. It is convenient to upgrade for software. 

It uses standard SNMP (Simple Network Management Protocol).

The communication protocol of version 3.7 of FiberHome Wview Network Management System conforms to SNMP V1 (RFC 1155-1157) and SNMP V2c proposed by IETF. According to the five management function of network management, such as configuration management, fault management, performance management, security management, account management and etc. It uses object-oriented design to achieve multi task processing. The dynamic distributed processing of Manager and Agent is real-time. It has a graphical interface. A variety of vivid images and simple graphics operation is very convenient to use.


1-1

Chapter2 System Requirement and Installation Guide

Chapter2 System Requirement and Installation Guide 2.1 Overview FiberHome Wview Network Management System is based on the C/S architecture of distributed network management system. And it supports for multiple client and server deployment. This chapter mainly introduces hardware platform, specific configuration requirements, system running environment and the installation, startup and unloading method of FiberHome Wview Network Management System. This chapter includes the following topics: Content

Page

2.1 Overview

2-1

2.2 Hardware Platform and Software Environment

2-1

2.3 Software Installation and Uninstallation Instructions

2-2

2.4 Software Using Instruction

2-15

2.2 Hardware Platform and Software Environment Purpose This section introduces hardware platform and configuration requirements of the FiberHome Wview Network Management System and the operation environment required for the software.

2.2.1 Hardware Platform Configuration Requirements 

The hardware platform of FiberHome Wview NMS(NMS for short) is PC Server(such as DELL POWEREDGE 1300 etc).



System memory is required to be above 512M, recommended to be above 1G. System virtual memory is recommended to be above 100M.


2-1




Hard disk requires above 10G and we recommended to be 20G. It is mainly for storing a large number of network management data.



CPU requires Intel PIII 500E and above, recommended to be Intel PIII 800EB.



CD-ROM is recommended to be above 40X.



The size of monitor is suggested to be above 17’’.



Need to be connected with network equipment through Ethernet, and the network management equipment can offer access to the network management server actively.

2.2.2 Software Environment Configuration Requirements The requirements of FiberHome Wview NMS operating environment are as follows: 

OS is recommended to be Windows NT4.0 pack 6 or above Windows 2000.



Display resolution: recommend that the display screen area is set to above 1024 ×768 pixels, so that one can get better display effect. If running the program in 800×600 pixels, it maybe shows an incomplete phenomenon.

2.3 Software Installation and Uninstallation Instructions Purpose This section introduces the installation and uninstallation steps of FiberHome Wview NMS. Content The name of network management system is NM-WView-Platform_version number.exe. According to user requirements, the following installation can be done. 

Only install server program.



Only install client program.



Install system server and client program at the same time.


2-2


2.3.1 Install Client Purpose This section introduces how to install client of FiberHome Wview NMS. Steps 1 ． Running the installation program of FiberHome Wview NMS, it first shows decompression interface as shown in figure 2-3-1.

Figure 2-3-1 Main Program Decompression Interface

2．After decompression, it shows the following installation interface of FiberHome Wview NMS as shown in figure 2-3-2.

Figure 2-3-2 Main Installation Interface


2-3


3．Select the installation language, enter OK button, it shows the following interface as shown in figure 2-3-3.

Figure 2-3-3 NMS Installation Introduction Interface

4．Enter next step button to choose installation place. The default place is ”C:\Program Files\WView NMS”, as shown in figure 2-3-4.

Figure 2-3-4 Choosing Installation Path Interface


2-4


5．Select install client, enter next step button, as shown in figure 2-3-5.

Figure 2-3-5 Pre-installation Abstract Interface

6．Enter next step button to continue installing, as shown in figure 2-3-6.

Figure 2-3-6 Installation Interface

7．Enter installation button to start installing, as shown in figure 2-3-7. FiberHome Wview Network Management System User Manual

2-5


Figure 2-3-7 Installation Process Interface of Server Program

8．Select restart system, enter finish button, as shown in figure 2-3-8.

Figure 2-3-8 Installation Finishing Interface of Server Program

2.3.2 Install Server Purpose FiberHome Wview Network Management System User Manual

2-6


This section introduces how to install server of FiberHome Wview NMS. Steps 1 ． Running the installation program of FiberHome Wview NMS, it first shows decompression interface as shown in figure 2-3-9.




3．Select the installation language, enter OK button, it shows the following interface as shown in figure 2-3-11. FiberHome Wview Network Management System User Manual

2-7





5．Select install server, enter next step button to continue, as shown in figure 2-3-13.


2-8





7．Enter installation button to start installing, as shown in figure 2-3-15.


2-9


Figure 2-3-15 Installation Process Interface of Server Program


Figure 2-3-16 Installation Finishing Interface of Server Program

2.3.3 Install Server and Client Purpose FiberHome Wview Network Management System User Manual

2-10


This section introduces how to install server of FiberHome Wview NMS. Steps 1 ． Running the installation program of FiberHome Wview NMS, it first shows decompression interface as shown in figure 2-3-17.




3．Select the installation language, enter OK button, it shows the following interface as shown in figure 2-3-19. FiberHome Wview Network Management System User Manual

2-11





5． Select install client and server, enter next step button to continue, as shown in figure 2-3-21.


2-12





7．Enter installation button to start installing, as shown in figure 2-3-23.


2-13


Figure 2-3-23 Installation Process Interface of Server and Client Program


Figure 2-3-24 Installation Finishing Interface of Server and Client Program


2-14


2.3.4 Uninstall Introduction Uninstalling this software, please choose to unload client and server of Wview NMS in the control panel/adding or removing program according to user’s requirement.

2.4 Software Using Instruction Purpose This section introduces the startup method, stopping method and user registration method of the server and client of the network management program. Content First, start the server, and then start the client. When exiting, first exit the client, then exit the server.

2.4.1 Start Server Steps 1．Click the “start server console” option of the “Wview NMS” program group in the “start” menu. 2．It shows login interface of server, as shown in figure 2-4-1.

Figure 2-4-1 Main Interface of Server


2-15


3．Click the “Register” button, if user has registered, it will show the following dialog box, as shown in figure 2-4-2.

Figure 2-4-2 NMS Server Registration Dialog Box

If user has not registered, the registration code column will be empty. If user has got registration code from our company website, please use the code to fill in the dialog box, and then click the register button to complete the registration. Click the return button to be back to the main window. 4．Click the configuration button to enter the configuration interface, as shown in figure 2-4-3.

Figure 2-4-3 Configuration Interface of Server


2-16


5．It needs relevant software to support the CORBA service option, as the above figure. Click the application button to save configuration.

2.4.2 Start Client Steps 1．Click the “start client” option of the “Wview NMS” program group in the “start” menu. 2．It shows login interface of client, as shown in figure 2-4-4.

Figure 2-4-4 Login Interface of Client

3．Input username, password and server IP address or server name, then click the confirm button to enter the main interface of client, as shown in figure 2-4-5. If input wrong password for three times, it will prompt the user that this username is locked (except the root user).


2-17


Figure 2-4-5 Login in the Main Interface of Client

2.4.3 Exit Client Steps 1．Use the mouse to select “system” menu, and then click . As shown in figure 2-4-6.

Figure 2-4-6 Exit FiberHome Wview NMS


2-18


2.4.4 Stop Server Steps 1．User can click the stop menu of the tray menu to manually stop the server program. As shown in figure 2-4-7.

Figure 2-4-7 Tray Menu of Server

2.4.5 User Registering Steps 1．Click [Get Registration Code →Next Step →Register] on server registration dialog box of the FiberHome Wview NMS. As shown in figure 2-4-8, 2-4-9 and 2-4-10.

Figure 2-4-8 Getting Registration Code


2-19


Figure 2-4-9 Clicking Next Step

Figure 2-4-10 Getting Installation Code

2．After getting installation code, please input the following website in the IE browser to enter user registration interface. http://www.fhn.com.cn:8080/regWview/regWview.do 3．Enter user registration interface, input user information and installation password.

Attention:

Email and telephone is optional. If user fill in these information, please make sure that email and telephone is consistent with the information when user first registered.


2-20


4．Be back to Wview platform to fill in the registration code. As shown in Figure2-4-14.

Figure 2-4-14 Filling in the Registration Code

2.4.6 Operation Introduction Content In this system, the management objects have: network topology, the entire device, device interface, equipment software and hardware. Each management object in the interface has corresponding icon. The basic operation method of the management object is that using the mouse to click the tools button on the tool strip, or right-click the pop-up menu item of each device node on the topological graph, or using the mouse to click each image object of the device configuration graph. Using the corresponding operation introduced above, user can get information of the management object.


2-21

Chapter3 Main Interface Function Introduction

Chapter3 Main Interface Function Introduction 3.1 Overview This chapter describes all features with description of FiberHome Wview Network Management System menu.It consists of" system"," topology"," warning"," prompts"," log"," performance"," configuration"," tools"," report"," business" and" help" etc 11 items in all. This chapter includes the following topics: Content

Page

3.1 Overview

3-1

3.2 System Menu

3-1

3.3 Topology

3-20

3.4 Trap Management

3-47

3.5 Prompt Column

3-82

3.6 Log

3-85

3.7 Performance

3-98

3.8 Configuration

3-137

3.9 Tool

3-166

3.9.1 Report

3-172

3.10 Service

3-175

3.11 Help

3-182

3.2 System Menu Objective This section describes the" system" menu includes" user switching"," security", "change

password","

export

registration

information","

import

registration

information"," system locking"and " the system"menu. Procedure The system menu is as shown in Figure3-2-1.


3-1

Chapter3 Network Element Management Module Introduction

Figure3-2-1 “System”item

3.2.1 Switch User Objective This topic introduces the user how to switch user. Procedure 1． Chick，the system is as shown in Figure3-2-2.

Figure3-2-2 User Switch confrim window

2． If the user select〈cancel〉button，the user will not exit the system。 3． If the user select (OK〉button，the system will back to the window as shown in 到如 figure 2-4-5 appears。


3-2


3.2.2 Security Management Objective This topic introduces the user how to manage security. Procedure 1．Click“Security Management”，as shown in Figure3-2-3 appears.

Figure3-2-3 Security Management

The user can be able to configure the following four management operation as required. Default operation is to start user managemen. The following steps describe the specific operations of security management. 3.2.2.1 User Managment Objective This topic introduces the user how to configure user management. Procedure User management is divided into seven parts:  View the user information 1． Click the" user management" button appears on the right panel, a list of all users, the user can use the menu to the user management


3-3


2． Click the "user management" button. all users information appear on the right panel, the user can be able to manage user ,as shown in Figure3-2-4.

Figure3-2-4 User management



Adding user

1． Select the popup menu in" Create user information", the window shown in Figure3-2-5 appears.

Figure3-2-5 Add User(1)


3-4


The user name, password confirmation, user group can't be empty. User name can not be repeat with other user name, the effective length of password is 4-16 bits. 2． Click the next button as shown in Figure3-2-6, the user can configure the user password security detection, IP address binding. Enable password password security detection. The effective length of password is 6-16 bits and the password must contain a combination of uppercase

Figure3-2-6 Add Use (2)

3． Click button, the system can create a new user.



Modify User

1． To modify the user, right-click menu, select" modify user information”, the window as shoiwn in Figure3-2-7and 3-2-8 appears, including the basic attribute and the safety control.


3-5


Figure3-2-7 Modify User(1)

Figure3-2-8 Modify User (2)

2． Click button.



Delete User


3-6


1． Select the user which need to be deleted. Right-click the menu, select" delete user information” as shown in the Figure3-2-9.

Figure3-2-9 删除用户

2．Click. 

Unlock the User

1． Input the error password five times, the system will be lock, the operator must use the root user or other authorized user login in.The user can select the lock user name andright-click menu, select"unlock the user”, the window as shown in Figure3-2-10 appears

Figure3-2-10 Unlock User

2．Click button. 

Lock User

1． Select the lock user in the user list, right-click menu, select "user lock", the window as shown in Figure3-2-11 appears.


3-7


Figure3-2-11 Lock User

2．Click button.



Modify User Password

1． Slect the user who need to be modify password, click the pop-up menu, select" modify user password", the window is shown in Figure3-2-12

Figure3-2-12 Modify User Password

2． Input the new password and inpur the password again, click button. 3.2.2.2 User Group Management. Objective This topic introduces the user how to manage the user group. Procedure


3-8


the user group can be devided into the following parts： 

Search User Group Click the" user group" button appears on the right panel, The System will generate 4 user group automatically, includes system management,

system

operation,

system

monitoring

and

maintenance as shown in the Figure3-2-13 appears.

Figure3-2-13 Rearch User Group



Adding the User Group Click right-click pop-up menu from user group list, select" create user group information"which appears the “increase user group: dialog box, If the user select the" super operation", the user group has full permissions. Click < ENTER > to create a new user group as shown in the Figure3-2-14 appears.


3-9


Figure3-2-14 Add the User Group



Mofidying the User Group In the user list selected which the user group need to be modified, right-click pop-up menu, select" modify user group information" which appears in the Figure3-2-15, the window includes modify user group name, modify user groups description and permissions described tree user group permissions.


3-10


Figure3-2-15 Mofidy the User Group



Deleting the User Group In the user list select the user group need to be deleted, right-click pop-up menu and select" delete user group information". Click < OK> button, the can delete the selected user group is as shown in Figure3-2-16


3-11


Notes: The user group which has been allocated the user can not be deleted

Figure3-2-16 Delete the User Group

3.2.2.3 Management Domain Configuration Objective This topic introduces the user how to configure the management domain Procedure 

Search Management Domain Click“Management Domain” icon ， the window is as shown in Figure3-2-17.


3-12


Figure3-2-17 Search Management Domain



Create Management Domain In the management of the domains list, right click" create management domain" button and input management domain name, description, and select the management domain of the right tree panel, click < OK > button as shown in the Figure3-2-18 appears.


3-13


Figure3-2-18 Create Management Domain



Mofidify the Management Domain

1． In the management domain selecte the management domain which need to be modified, right-click pop-up menu and select" change management domain", as shown in the Figure3-2-19.


3-14


Figure3-2-19 Mofidify the Management Domain

2． Click button. 

Delete Management Domain Select the management domain which need to be delete. Right-click pop-up menu and select" delete management domain", click < OK > button, as shown in the Figure3-2-20.

Figure3-2-20 Delete Management Domain


3-15


3.2.2.4 View Oline User Objective This topic introduces the user how to View the Oline User. Procedure Click the" view online users" button, the system will display a list of online users. Which is as shown in Figure3-2-21..

Figure3-2-21 View the Oline User

3.2.3 Modify User Password Objective This topic introduces the user how to modify the user password. Procedure Click the "mofidy password" button which as shown in Figure3-2-22 appears. Click "OK"

button.


3-16


Figure3-2-22 Modify User Password

3.2.4 Export Registration Information Objective This topic introduces the user how to export the registration information. Procedure Click the" export registration information" button which as shown in the Figure3-2-23. Select export registration information and click the button shown in the Figure3-2-24 appears..


3-17


Figure3-2-23 Export Registration Information (1)

Figure3-2-24 Export Registration Information (2)

3.2.5 Import Registration Information Objective This topic introduces the user how to import registration information. Procedure Click the" import registration information" button which as shown in the Figure3-2-25, the user can select which registration information need to be imported, and click the "open", buttonas shown in the Figure3-2-26 appears.


3-18


Figure3-2-25 Import Registration Information (1)

Figure3-2-26 Import Registration Information (2)

3.2.6 Lock System Objective This topic introduces the user how to lock the system Procedure Click the" system locking" or using the shortcut CTRL+L system, enter a password to unlock shown in the Figure3-2-27. In addition, if the system has no operation in 20 minutes, the system will lock.automatically


3-19


Figure3-2-27 Lock System

3.2.7 Exit System Objective This topic introduces the user how to exit the system. Procedure 1．Click“exit system”，the window is as shown in Figure3-2-28：

Figure3-2-28 Exit the System

2．Click button.

3.3 Topology Objective This topic introduces the user how to manage Topology. Procedure As shown in Figure3-3-1," topology" menu includes as follows: the network view, topology breviary , searching topological node, searching network equipment, export topological site information and import topological information site. FiberHome Wview Network Management System User Manual

3-20


Figure3-3-1 Topology

3.3.1 Network View Objective This topic introduces the user how to configure network view. Procedure When the user selects the menu item, the window is as shown in the 3-3-2, the different color of equipment icon background represent equipment different state. The default color is as shown in the below table, the user can configuration the color under the “configuration warning" or" configuration \ configuration topological node" menu. At the same time, the topological tree leaf nodes may display the corresponding icon in the left side. The equipment icon will show in red color when the equipment alarms.

Table 3-1 Equipment icon backgroud Color Introduction Represent device can be connected and no alarm information Represent device is not currently connected Represen device received level 1alarm


3-21

Chapter3 Network Element Management Module Introduction Represen device received level 2alarm Represen device received level 3alarm Represen device received level 4alarm Represen device received level 5 alarm

Figure3-3-2 Topology

3.3.1.1 Topology Tree Objective This topic introduces the user how to configure topology tree. Procedure Above the left Topological Viewgraphis the topology tree, it shows topology Viewgraphand equipment list. The user can be able to quickl view all views the node of the device node topology In the topology view, as well as the device node the current state, whether the warning information, and through the pop-up menu to select the tree node operations.It shown as in Figure3-3-3 appears:


3-22


Figure3-3-3 Topology Tree

The user can be able to view and manage all the devices when click the " list of devices" button, and the user can add, modify , delete the devices, ping ,telnet , use mib, use web ,refersh node, configure alarms, delete nodes, configure the node attribute, lock the node, alarm filtering and etc. 3.3.1.2 Information Column Objective This topic introduces the user how to configure information column. Procedure The upper right corner information column of Network management display the alarm information: includes alarm level and various alarm colors, five level alarm indicates in red, four level alarm indicates in orange, three level alarm indicates in yellow, two level alarm indicates in blue, one level alarm indicates in purple, the statistics number of alarm is as shown in Figure3-3-4 at the same time:

Figure3-3-4 Alarm Information


3-23


Note： When the alarm occurs, the system will flicker and show alarm number.

3.3.1.3 Topology View Objective This topic introduces the user how to configure topology view. Procedure In the network view, the right side of the tab to display the topology view, the user can be able to open multiple topological view, equipment panel, the window show in Figure3-3-5 and3-3-6 appears.

Figure3-3-5 Topology View


3-24


Figure3-3-6 Device Panel

The user can be able to view Viewgraph, view or modify each node or link attributes of the view, or delete part of viewgraphnode and connection according to their own permission. The user can use the viewgraphon the left side of the toolbar or right-click pop-up menu to complete these topological operations. Refer to 3.3.7, 3.3.8, 3.3.9and 3.3.10 section for obove operations details.

3.3.2 Topology Thumbnail Objective This topic introduces the user how to configure topology thumbnail. Procedure Click the" topological thumbnail" menu item, it will shown in the Figure3-3-7, the window indicate the current topology viewgraphthumbnail..


3-25


Figure3-3-7 Topology Thumbnail.

3.3.3 Search Topology Node Objective This topic introduces the user how to search topology node. Procedure Click the Topology Node item, the window will shown in Figure3-3-8 appears.The user can be able to set up four query condition to query devices.

Figure3-3-8 Search Topology Node

Example For example, when the user input device node IP address, the user will find the topological node results in the following dialog, as shown in Figure3-3-9:


3-26


Figure3-3-9 The result of Search Topology Node

Double-click one of the search node list can open the node 's view, select the node. It as shown in the Figure3-3-10 appears.


3-27


Figure3-3-10 search node list

3.3.4 Search Network Device Objective This topic introduces the user how to search network device. Procedure 1． Click the" search network equipment" menu, it as shown in the Figure3-3-11 appears.


3-28


Figure3-3-11 Search Network Device

2． The user only need to input the network address range, then the user will find all online network equipment

in the network segment, for the unopen SNMP service

equipment, the user can not find its model.. 3． Select a device, right-click pop-up menu, the user can select and add the device" to the specified view", or save it to viewgraphaccording to IP automatically. Function. 4． Users select the "add to the specified view", the system is as shown in Figure3-3-12. After the user selecte node, click < OK > , the node can be joined tothe view, if add successfully, the device will disappear from the search list of devices, otherwise, the system will pop-up dialog box to explain user the reason for the failure.


3-29


Figure3-3-12 Join the search network device

If the user select “automatically added to the viewgraphaccording to the IP ", the system will add the node corresponding to the configuration IP address segment of the viewgraphautomatically, and the node is removed from the table. the system will not add when the IP address of the device and the existing equipment conflict.

3.3.5 Export Topology Site Information Objective This topic introduces the user how to export topology site information. Procedure 1． Click the" derived topological site information", the window is as shown in the Figure3-3-13


3-30


Figure3-3-13 Export Topology Site Information

2． Users select derived topological node, click < ENTER >, the system is shown in the dialog, the user enter the file name, select < save > button. It allows a topology site which is saved to a file. The following Figure3-3-14 shows below..


3-31


Figure3-3-14

Export Topology Site Information dialog

3.3.6 Import Topology Site Information Objective This topic introduces the user how to configure Import Topology Site Information Procedure 1． Click “Import Topology Site Information” item, the window is as shown in Figure3-3-15. User select the saved site files and open, the system will import the site information to the main program.


3-32


Figure3-3-15 Import Topology Site Information Dialog

2． After the user open, the window is as shown in Figure3-3-16. The user can be able to import the topology information of this file to the next node of current view. Click ,.


3-33


Figure3-3-16 Import Topology Node

3.3.7 Equipment Objective This topic introduces the user how to configure equipment menu item via right click. Procedure When righting click on viewgraphor topology tree node of equipment, the system will pop up as shown in the Figure3-3-17, different types of equipment will shown different menu. However, add device nodes manually have the same menu item: 1． Click“ping”，the system will ping the device using the command line window.; 2． Click“telnet”，the user can telnet the remote device; 3． Click“MIB tools”，the user can read MIB remotely; 4． Click “Web Configuration”，the use can connect the device via the browser;


3-34


5． Click “Refresh Node”，the user can test whether the device is connected, 6． Click“ Restart Device Model”，the user can correct and get the device model automatically; 7． Click “Viewgraph Alarms”，the system can switch to alarm log window to view the device alarm information; 8． Click “Clear ALarm”，the system will clear all the alarm information of the current device, the device could be able to restore to formal condition; 9． click the" alarm synchronization", the system can be synchronous equipment

node of the alarm information; 10． click" alert cache configuration", the system can be configured to cache

information equipment alarm

Figure3-3-17 Right-click equipment menu item

3.3.8 Viewgraph Objective FiberHome Wview Network Management System User Manual

3-35


This topic introduces the user how to configure viewgraph menu item. Procedure When the user right click topology tree viewgraph nodes, the system will pop up the menu shown as in Figure3-3-18 appears. If the user double-click the viewgraph point, the default implementation of the popup menu in the first operation.

Figure3-3-18 Right-click viewgraph menu item



Open the View

Click “Open the View”，the system will add a tab upon the topology figure and display all topology of this view, it is as shown in Figure3-3-19.


3-36


Figure3-3-19 Open the view



Attribute of the Node

1．Click “Attribute of the node”，the system will shown as in Figure3-3-20.

Figure3-3-20 Modify viewgraph FiberHome Wview Network Management System User Manual

3-37


2．Click “Advanced”，the system will shown as in Figure3-3-21 appears. The IP address segment which user added cannot be confilict with other IP address segment..

Figure3-3-21Ip address configuration

3.3.9 Unselected Nodes Objective This topic introduces the user how to configure unselected nodes via right click menu itmes. Procedure Right click the bank region; the system is as shown in Figure3-3-22:


3-38


Figure3-3-22 Add Device menu

3.3.10 Toolbar Toolswill be in the viewgraph left when opened .it includes the ' refresh ', ' Browse ' topology topology, increases the link ', ' ', ' viewgraph ' increase increase equipment ', ' ', ' change the properties of topological delete ', ' ', ' left alignment right justified ', ' up ', ' down ' alignment alignment, horizontal distribution ' ' ', ' ', ' vertical distribution amplifier. 3.3.10.1 Refresh Topology Objective This topic introduces the user how to refresh topology. Procedure Click the" refresh topological" button [

], the system will be shown in Figure3-3-23:

Figure3-3-23 Refresh Topology


3-39


Click , the system will open the network viewgraph window, it will show the newest topology of the database. 3.3.10.2 Viewgraph Topology Objective This topic introduces the user how to configure viewgraph topology. Procedure Click , the viewgraph from the increasing connection mode is switched to the browse mode, the default is the browse mode. 3.3.10.3 Add a Connection Objective This topic introduces the user how to add a connection. Procedure 1． Press the [

] button, the Viewgraphfrom the browse mode switch to add the

connection mode. Under this mode, use the mouse to click on the two nodes, i.e. the system will be shown in the Figure3-3-24. The user input the connection attribute, the system will generate a line between 2 nodes.


3-40


Figure3-3-24 Add a line

2． User input the connection name, and select the corresponding line type, if the node is the equipment node, the can select the device port, it is as shown in Figure3-3-25.

Figure3-3-25 Add a connection line


3-41


Note： Under add connection mode, the user can only add the connection, if the user want to move the nodes or do other operations, the user need to switch to browse mode.

3.3.10.4 Add a Viewgraph Objective This topic introduces the user how to add a viewgraph. Procedure 1.

Click [

] button，the system will be shown as in Figure3-3-26.

Figure3-3-26 Add a Viewgraph

2.

In the Figure3-3-26, the viewgraph name can't be empty. Click OK to generate a view point. The user can also click < advanced > button to configure the IP address range of the viewgraph, a viewgraph can be configured with multiple unconflict IP address range. As shown in the Figure3-3-27.


3-42


Figure3-3-27）Add a viewgraph(advanced)

3.3.10.5 Add a Device Objective This topic introduces the user how to add a device. Procedure 1.

Click [

] button，the system will be shown as in Figure3-3-28.


3-43


Figure3-3-28 Add a device-1

2.

The device name cannot be empty，the user must select the device type. And then click ，it is as shown in Figure3-3-29.


3-44


Figure3-3-29 Add a device-2

3.3.10.6 Modify the Device Objective This topic introduces the user on how to modify the device. Procedure [

] button indicates “disable” as default, when a node or a line has been selected,

the state change to "enable", click the button, the system will pop up different modify attribute dialogs according to the selected nodes or links of different types and different modifications. 3.3.10.7 Delete the Topology Objective This topic introduces the user how to delete the topology. Procedure FiberHome Wview Network Management System User Manual

3-45


[

] button indicates “disable”as default, when the user select nodes or links, the

corresponding buttons status changed to "enable", click the button, the system will pop up the window of" whether to delete?" Dialog: Click "OK" button, the user can delete the selected nodes or links and can be delete multiple nodes at the same time. 3.3.10.8 Move a Node Objective This topic introduces the user how to move a node. Procedure To implement node moving, click to select one and drag it to destination. To modify curved of line, click to select one and drag the midpoint of line to destination. To implement the moving of multiple nodes and lines, click multiple nodes and lines and drag one of nodes to destination. 3.3.10.9 Alignment Objective This topic introduces the user how to configure the nodes alignment Procedure There are six kinds of alignment [

],[

],[

],[

],[

],[

] ,respectively to "

alignment"," snaps downward"," left alignment"," right alignment"," distribution"," vertical distribution". Default value is "disable", when select the alignment nodes, the status change to “enable”. 3.3.10.10 Zooming Objective This topic introduces the user how to configure zooming. Procedure There are three kinds of zooming modes [

], [

], [

], indicate "zoom"," narrow","

recovery" respectively.


3-46


3.4 Trap Management Objective This topic introduces the user how to manage Trap. Procedure As shown in the Figure3-4-1" Trap" menu includes" Trap log"," Trap configuration"," Trap filtering or shield"," troubleshooting experience" .

Figure3-4-1 Trap Item

3.4.1 Trap Log Objective This topic introduces the user how to configure trap log. Procedure Click , the system will pop up as shown in the Figure3-4-2,, the user can be able to configure " current Trap"," Trap history" and" all the Trap" management when select different button


3-47


Figure3-4-2 Trap Log Interface

3.4.2 Trap Configuration Objective This topic introduces the user how to configure trap. Procedure click , the system will pop up as shown in the Figure3-4-3, the user can be able to configure following items:" configuration trap parameters"," configuration warning notice"," configuration trap level"," historical trap definition" and " configuration trap suppression " configuration.


3-48


Figure3-4-3 Configure Trap

3.4.2.1 Configure Trap Level Objective This topic introduces the user how to configure trap level. Procedure To configure trap level, double-click the item, the system will be shown in the Figure3-4-4, the device node shows background color to clew user whether the warning information, whether the audible trap and voice frequency or vocalizations using WAV sound. When a certain level of warning is hidden, the system will loose the received level trap information. Click the" restoration of the initial value", the system can be restored to the initial state of the prompt parameter.


3-49


Figure3-4-4 Congirue Trap Level Parameters

1.

Click "trap" table entry, the system will pop up the window shown in the Figure3-4-5, users can define different trap color.


3-50


Figure3-4-5Configure Trap Color

2.

Click the" trap sound" table entry, the system will pop up the window shown in the Figure3-4-6, users can customize the various warning level trap sound.


3-51


Figure3-4-6Configure Tap Voice

3.

Click , the trap information will be save to she system.

3.4.2.2 Configure Trap Notification Objective This topic introduces the user how to configure trap notification. Procedure 1.

Double click “configure trap notification”, the system will be shown as in Figure3-4-7.


3-52


Figure3-4-7 Configurae Trap Notification

2.

Right click the interface, the window is as shown in Figure3-4-8

Figure3-4-8 Right click window with configure trap notification



Click button, the system will be shown in Figure3-4-9.


3-53


Figure3-4-9 Create Contact window1

 

Selected the contact which has been created, click < modify contact information > or t< delete contact information>. Selected the contact which has been created, click < configuration trap notice or click" trap notification" of the contact information, the system is as shown in the Figure3-4-10display.

There are 2 methods to configure trap notification rule:  

Click" trap type"," trap device" or " trap level" button. Query the trap rule which has been configured.


3-54


Figure3-4-10 Create Contact window2

Click "add" button, the system will pop-up the window as shown in Figure3-4-11. Query and select the trap which need to be configured, Select the "mail" or" the message", and click < ENTER > button to create the trap notification rules.


3-55


Figure3-4-11 Configure the trap type



To configure the trap level rules, the window is as shown in Figure3-4-12.


3-56


Figure3-4-12 To configure trap level notification rules

To configure the trap notification rule, click button, the system will be pop-up as shown in Figure3-4-13, and then select the trap type, choose to send mail or send a short message.


3-57


Figure3-4-13 Configure trap notification rules



To configure trap notification by using trap line, the window is as shown in Figure3-4-14.


3-58


Figure3-4-14 Configure trap notification by using trap line1

To configure trap notification by using trap line, click < add > button, the window pop-up as shown in. Figure3-4-15, select trap card, and then select the trap type, choose to send mail or send a short message.


3-59


Figure3-4-15 Configure trap notification by using trap line2



To configure trap notification by using trap port, the window is as shown in Figure3-4-16.


3-60


Figure3-4-16 Configure trap notification by using trap port1

To configure trap notification by using trap port, click < add > button, the window pop-up as shown in. Figure3-4-17, select trap card, and then select the trap type, choose to send mail or send a short message.


3-61


Figure3-4-17 Configure trap notification by using trap port2



To configure trap notification by using trap level, the window is as shown in Figure3-4-18.


3-62


Figure3-4-18 Configure trap notification by using trap level1

To configure trap notification by using trap level click < add > button, the window pop-up as shown in. Figure3-4-19, select trap card, and then select the trap type, choose to send mail or send a short message.

Figure3-4-19 Configure trap notification by using trap level2

To configure trap notification rule, select the trap notification rule by using " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap notification rule interface FiberHome Wview Network Management System User Manual

3-63


To refresh trap notification rule, select the trap notification rule by using " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap notification rule interface To save trap notification rule, modify " mail"," short message", "enable" option in " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap notification rule interface window. Note that, if the enabled trap notification rules has not been selected, the trap notification rule will not been taken effect. The default value is " enabled" of trap notification rules. 3.4.2.3 Configure Trap Parameters Objective This topic introduces the user how to configure trap parameters. Procedure To modify trap parameters, double click “configure trap paramters”, the window is as shown in Figure3-4-20. Click button.

Figure3-4-20 Configure Trap Parameters

3.4.2.4 Define Trap History Objective FiberHome Wview Network Management System User Manual

3-64


This topic introduces the user how to define trap history. Procedure To define trap history, double “trap history” button, the system is as shown in Figure3-4-21. Click button.

Figure3-4-21 Define Trap History

3.4.2.5 Configuration Trap Inhibition Objective This topic introduces the user how to configuration trap inhibition. Procedure To configure trap inhibition, double “configure trap inhibition” button, the system is as shown in Figure3-4-22. Click button.


3-65


Figure3-4-22 Configuration Trap Inhibition

To add trap inhibition, the window as shown in Figure3-4-23 appears.

Figure3-4-23 Add Trap Inhibition


3-66


3.4.3 Trap Filtering or Shield Overview Trap filter of network management system receives the alarm information, save to alarm log, but it will not display in the trap column. Trap shield is not receiving the trao information and not save to alarm log. Trap filtering is devided into " trap type"," warning device"," trap card"," trap port" and" alert level" to filter or shield. When configuring the trap filtering or shield rules, if the user does not select trap shield option, the default value is trap filtering. Also, the user can configure the trap time, Military Time, the end time of trap time must be greater than or equal to start trap timeevery day. If the user configure the trap filtering or shield rules from 23:00:00 to 2:00:00, it can be configured as two trap filtering or shield rules. As the first rule was set from 23:00:00 to23:59:59, the second rule will be set from00:00:00 to 02:00:00. Procedure Trap filtering or shield configuration interface as shown in the Figure3-4-24 appears Trap filtering is devided into " trap type"," warning device"," trap card"," trap port" and" alert level" to filter or shield. Also the user can be able to query the configured alarm filtering or shield rules according to the corresponding query trap. At the beginning of loggin the interface of “configure trap filtering/ shield”, the user can query the configured trap filtering/ shield” after the user query trap information.


3-67


Figure3-4-24 Trap filtering or shield1



To configure trap filtering or shield by using “trap type”

Click “add” button, the system is as shown in Figure3-4-25. After select the required trap type then click button.


3-68





To configure trap filtering or shield by using “trap device”, the window is as shown in Figure3-4-26.


3-69



To configure trap filtering or shield by using “trap device”, Click “add” button, the system is as shown in Figure3-4-27. After select the required trap device then click button


3-70





To configure trap filtering or shield by using “trap line”, the window is as shown in Figure3-4-28.


3-71



To configure trap filtering or shield by using “trap line”, the window is as shown in Figure3-4-29. After select the required trap line and type then click button


3-72





To configure trap filtering or shield by using “trap port”, the window is as shown in Figure3-4-30.


3-73



To configure trap filtering or shield by using “trap port”, the window is as shown in Figure3-4-31. After select the required trap port and type then click button


3-74



To configure trap filtering or shield, select the trap filtering or shield by using " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap notification rule interface To configure trap filtering or shield, select the trap filtering or shield by using " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap notification rule interface To configure trap filtering or shield, modify " mail"," short message", "enable" option in " trap type"," warning device"," trap card"," trap port" and" alert level" five query trap filtering or shield interface window. Note that, if the enabled trap filtering or shield has


3-75


not been selected, the trap filtering or shield will not been taken effect. The default value is " enabled" of trap filtering or shield.

3.4.4 Troubleshooting Objective This topic introduces the user how to configure troubleshooting. Procedure Troubleshooting of the network management system receives the trap information, and save the trap information to trap log. User can be able to add the trap reason,trap solution and result by right click item of the trap log or trap prompt column. The user can be albe to view the formar trap reason, trap sultion and trap reason when meeting the similar trap on the same location, refer to Figure3-4-32 and 3-4-33.

Figure3-4-32 Troubleshooting1


3-76



Click the "add troubleshooting experience" menu, as shown in the Figure3-4-34, the user can select the trap reason. If it is not in trap option, the user can also click < other > then input the trap reason, trap processing and trap results. To add a trap, the user can click button, if there are multiple traps, the user can select delete the trap information of “traps with troubleshooting”. The system can list the trap experience information since there has one trap information at least.


3-77



Click “trap” button from the system item, select “troubleshooting” item, the system is as shown in Figure3-4-35.


3-78



The user can be able to implement " increase troubleshooting experience"," modify troubleshooting experience"," delete troubleshooting experience"," troubleshooting experience attribute"," all derived from"," front," derived and " export options" from the " troubleshooting experience" management interface, the system is as shown in Figure3-4-36.


3-79



Click “”the same type of troubleshooting experience" from the trap column and trap log, the system is as shown in Figure3-4-37and Figure3-4-38.


3-80




3-81



3.5 Prompt Column Objective This topic introduces the user how to configure the prompt column. Procedure The prompt column includes 2 items of “trap prompt column” and “event prompt column”.


3-82


Figure3-5-1 Prompt Column1

To isolate the main interface of information column from separate interface, click to select and drag information column.

3.5.1 Trap Prompt Column Objective This topic introduces the user how to configure trap prompt column. Procedure Click the “Trap Prompt Column”menu, the system will start the alarm monitoring automatically.as shown in Figure3-5-2 appears. The system will show the received trap information. The background color of viewgraph and topological tree nodes will change with the trap level change, the count of trap information will be increased corresponding.


3-83


Figure3-5-2 Trap Prompt Column1

The user can use the window as shown in Figure3-5-4 to confirm trap or trap is cleared. Delete the traps when confirming the trap is cleared. The user can be albe to locate the alarm device.

Figure3-5-3 Trap Prompt Column2

3.5.2 Event Prompt Column Objective This topic introduces the user how to configure event prompt column. Procedure To start the event prompt column, select this menu and the window is shown as in Figure3-5-4.


3-84


Figure3-5-4 Event Prompt Column

If this item is not choosen, the syste will stop the event listening, the event prompt column will be disappear.

3.5.3 Event Prompt Synchronization Objective This topic introduces the user how to configure event prompt synchronization. Procedure If the user has changed topology, synchronous event will be changed when notifying other user topology which en changed. The synchronous information will be shown in Figure3-5-5.

Figure3-5-5 Event Prompt Synchronization

3.6 Log Objective The section introduces contents and functionalities of “Log” menu. Procedure Referring to Figure3-6-1, the drop down menu of “Log” includes 5 facilities: “Security Log”, “Operation Log”,”Event Log”, “Performance Log” and “Log Backup”. The trap log can be queried from trap management.


3-85


Figure3-6-1 Log Menu Facilities

3.6.1 Security Log Objective The section introduces configuration of “Security Log” menu. Procedure Select “Security Log” from the aboe figure and security log configuration page will be shown as Figure3-6-2. Number of log item being displayed in each page can be defined by the user, as well as log query condition that the user is able to input query details in the column of “Query Condition” to check specific security log.

Figure3-6-2 Security Log

Select one log item from the above list and right click, “Operation Log Report Management” window will be poped up as shown as Figure3-6-3:


3-86


Figure3-6-3 Security Log Report Header Configuration

Click “Export Report” button and the dialog for report save will be shown as Figure3-6-4:

Figure3-6-4 Saving Security Log Report

Click “Check Report” button and the window of report preview&print will be shown as Figure3-6-5:


3-87


Figure3-6-5 Security Log Report Print Preview

Click “Print Property” button and the window of property individuation will be shown as Figure3-6-6:

Figure3-6-6 Security Log Report Print Property

3.6.2 Operation Log Objective


3-88


The section introduces configuration of “Operation Log” menu. Procedure Select “Operation Log” from Figure3-6-1, the operation log configuration page will be shown as Figure3-6-7. Number of log item being displayed in each page can be defined by the user, as well as log query condition that the user is able to input query details in the column of “Query Condition” to check specific security log.

Figure3-6-7 Operation Log

Select one log item from the above list and right click, “Operation Log Report Management” window will be poped up as shown as Figure3-6-8:


3-89


Figure3-6-8 Operation Log Report Header Configuration


Figure3-6-9 Saving Operation Log Report



3-90


Figure3-6-10 Operation Log Report Print Preview


Figure3-6-11 Operation Log Report Print Property

3.6.3 Event Log Objective


3-91


The section introduces configuration of “Event Log” menu. Procedure Select “Event Log” from Figure3-6-1, the event log configuration page will be shown as Figure3-6-12. Number of log item being displayed in each page can be defined by the user, as well as log query condition that the user is able to input query details in the column of “Query Condition” to check specific security log.

Figure3-6-12 Event Log

Select one log item from the above list and right click, “Evernt Log Report Management” window will be poped up as shown as Figure3-6-13:


3-92


Figure3-6-13 Event Log Report Header Configuration


Figure3-6-14 Saving Event Log Report



3-93


Figure3-6-15 Event Log Report Print Preview


Figure3-6-16 Event Log Report Print Property

3.6.4 Performance Log Objective The section introduces configuration of “Performance Log” menu. Procedure FiberHome Wview Network Management System User Manual

3-94


Select “Performance Log” from Figure3-6-1, the performance log configuration page will be shown as Figure3-6-17. Number of log item being displayed in each page can be defined by the user, as well as log query condition that the user is able to input query details in the column of “Query Condition” to check specific security log.

Figure3-6-17 Performance Log

Select one log item from the above list and right click, “Performance Log Report Management” window will be poped up as shown as Figure3-6-18:

Figure3-6-18 Performance Log Report Header Configuration



3-95


Figure3-6-19 Saving Performance Log Report


Figure3-6-20 Performance Log Report Print Preview



3-96


Figure3-6-21 Performance Log Report Print Property

3.6.5 Log Backup Objective The section introduces configuration of “Log Backup” menu. Procedure Referring to Figure3-6-22, trap log, security log, operation log and event log can be exported and backuped through the facility:

Figure3-6-22 Log Backup FiberHome Wview Network Management System User Manual

3-97


3.7 Performance Objective The section introduces contents and functionalities of performance management. Procedure Referring to Figure3-7-1, the drop down menu for “Performance” includes the item “Performance Management”:

Figure3-7-1 Performance Menu

The performance management contains 4 facilities, “Device Performance”, “Interface Performance”, “Service Performance” and “Link Performance”. For each of those object types there is a similar operation procedure that particular management object (device, interface, service or link) must be created first and performance template creation for device or interface comes after, performance instance creation for particular device binding with performance template at the last, showing as Figure3-7-2:

Figure3-7-2 Performance Management Main Page


3-98


3.7.1 Device Performance Objective The section introduces configuration of “Device Performance” menu. Procedure Click “Device Performance” item from the above main page referring to Figure3-7-2, the tab page appears as shown as fowllows in Figure3-7-3, including “Universal Device Resource”, “Universal Device Template” and “Universal Device Instance”.

Figure3-7-3 Device Performance

3.7.1.1 Universal Device Resource Management Objective The section introduces configuration of “Universal Device Resource”. Procedure Select “Universal Device Resource” from “Device Performance” page referring to Figure3-7-3. The “Universal Device Resource” displays created universal device resource. The created information can be queried by inputting query conditions such as name, type, IP address range, MAC and resource ordering. Right click item from universal device resource list and select “Import Device Resource” from popped up right click menu; the “Import Device Resource” dialog is shown as Figure3-7-4: FiberHome Wview Network Management System User Manual

3-99


Figure3-7-4 Importing Device Resource Page

The dialog lists both selected and optional device resources. Select one of the items from optional device resource list and click [

] button to move one device into

selected device resource list. Select all of the devices and press [

] button to move

all devices into selected device resource list. Those selected device resources also can be deleted that by clicking [

] to remove all selected ones and by clicking [

]

to remove single one, and click “Confirm” to save the configuration. Once the saves are successful, selected device will be displayed from universal device list, referring to Figure3-7-5:


3-100


Figure3-7-5 Importing Device Resource Result

To delete created device resource, select one of them, right click and select “Delete Device Resource” from popped up right click menu. If the instance to this device resource has been created, then the instance cannot be deleted. 3.7.1.2 Universal Device Template Management Objective The section introduces configuration of “Universal Device Template”. Procedure Select “Universal Device Template” from “Device Performance” page referring to Figure3-7-3. The “Universal Device Template” displays created universal device template, shown as Figure3-7-6:


3-101


Figure3-7-6 Universal Device Templat Page

The information of created universal template can be queried by inputting query conditions such as property, name, type, resource type and template ordering. The system defines a predefined template for each device with different types that the templat covers all supported performance indexes of the device type. 

Create customized template:

1. Right click universal device templet list, select “Create New Performance Template” from popped up right click menu and the “Create New Performance Template” dialog is shown as Figure3-7-7:


3-102


Figure3-7-7 Create New Universal Device Template-1

2. Select device type, input template name (required) and template description (optional) and second step dialog of created new performance template will appear by clicking “Next” button. In this dialog, selected performance resource index and optional performance resource index can be listed that by selecting an optional resource and click [

] button to move the resource into selected

resource list, and by selecting all the resources and click [

] button to move

those resources into selected resource list. The selected resource can also be deleted by clicking [

] for all selected resource removing and by clicking [

] for

single resource removing, referring to Figure3-7-8 below:


3-103



3. The third step dialog of created new performance template will appear by clicking “Next” button. Configurations of index name, index description and default threshold, default sampling interval etc. can be performed to selected performance index according to practical requirement in this dialog, referring to Figure3-7-9 below:



3-104


4. Click “Done” button to save new created template if the configurations are accomplished. Once the save is successful, the created customized template will be displayed in the universal performance template list, referring to Figure3-7-10 below:

Figure3-7-10 Creating New Universal Device Template Successful

If the created customized template is required to be modified, select the list row where the template displays and click the [

] button, the “Modify Performance Index”

dialog will be poped up as shown in Figure3-7-11. The modification which has similar procedure with the one when creating allowes the user to add, delete or modify to the property.


3-105


Figure3-7-11 Modify Performance Index



Delete created device template

Select a device template that needs to be deleted and right click, select “Delete Device Template” from the right click menu. If instance to the template has been created, then the instance cannot be deleted. 3.7.1.3 Universal Device Instance Objective The section introduces configuration of “Universal Device Instance”. Procedure 

Universal Device Instance Query

Select “Universal Device Instance” from “Device Performance” page referring to Figure3-7-3. The “Universal Device Instance” displays created universal device instance, shown as Figure3-7-12:


3-106


Figure3-7-12 Universal Device Instance Page

The information of created universal instance can be queried by inputting query conditions such as instance name, status, resource name, template name, sampling/report status and instance order. 

Create Universal Device Instance

1. Right click an item from universal device instance list and select “Create New Performance Instance” from the right click menu. The “Create New Performance Instance” dialog will appear as shown in Figure3-7-13 below, one or more device resources can be selected for further configuration.


3-107


Figure3-7-13 Create New Universal Device Instance-1

2. The second step dialog of created new performance instance will appear by clicking “Next” button. Select performance template corresponding with device type in step one from the dialog of second step of created new performance template, referring to Figure3-7-14 below:


3-108



Note： During the creation of device instance, performance index of instance in a same device cannot be duplicated. For example, device 1 creates two device instances, in which instance 1 binds with template 1 while instance 2 binds with template 2, in this cast performance index in template 1 and 2 shall not be duplicated, otherwise a failured prompt window will be popped up during the creation, referring to Figure3-7-15. Additionally, the prompt also appears when the selected device type does not match the template.

Figure3-7-15 Error Prompt in Create New Universal Device Instance


3-109


3. The third step dialog of created new performance instance will appear by clicking “Next” button, as shown as Figure3-7-16 below. The instance and template can be located then.


4. The forth step dialog of created new performance instance will appear by clicking the above “Next” button. The step is to establish start/stop to the instance. If auto start up is selected, then the starting to selected instance must be established in manual; if timing start up is selected, then the system will implement the starting according to defined time. Similarly, the instance stop obeys the same rule that it has two algorithms as auto start up and timing start up, referring to Figure3-7-17 below:


3-110



5. Click “Complete” button to finish the performance instance creation, referring to Figure3-7-18:

Figure3-7-18 Creating New Universal Device Instance Successful


3-111


Select an item from device performance instance list and right click, the right click menu appears as shown in Figure3-7-19. Every option in the menu can be seen from the tool bar as well.

Figure3-7-19 Universal Device Instance List



Delete universal device instance

Select a device performance instance item and right click, select “Delete Performance Instance” from the right click menu or click [

] button, and then click “Confirm” from

the confirmation dialog to delete the selected universal device instance. 

Set index parameter

Select a device performance instance item and right click, select “Set Index Parameter” from the right click menu or click [

] button, and then modify the

sampling time interval to the instance via the popped up index parameter setting dialog. 

Performance index management

Select a device performance instance item, press [

] button from the line where the

item being listed to check on performance index contained by the instance. If the selected performance instance is in stopped status, it is capable to re-proviison to the index name, description information, threshold and sampling time. 

Modify sampling&report plan


3-112


Select a device performance instance item, press [

] button from the line where the

item being listed to modify the starting/stopping plan of the instance. 

Start instance

Instance status can be shown from the instance list that the status is divided into “Stopped” and “Started”. If the selected instance is at “Stopped” status, then it can be started by selecting “Start Instance” from right click menu or by selecting [

] button.

Once the instance is started successful, the status would turn into “Started”, referring to Figure3-7-19 below:

Figure3-7-19 Started Device Performance Instance



Stop instance

If the selected instance is at “Started” status, then it can be stopped by selecting “Stop Instance” from right click menu or by selecting [

] button. Once the instance is

stopped successful, the status would turn into “Stopped”, referring to Figure3-7-20 below:

Figure3-7-20Stopped Device Performance Instance



Performance real-time Monitor

Performance real-time monitor is to perform real time monitor to one of the performance indexes of a device with sampling time interval 3 seconds. Select a device performance instance and press [

] button from the line where the item

being listed to check on the performance index contained by the instance. 1. Select a performance index and right click, the popped up window appears as shown in Figure3-7-21 below:


3-113


Figure3-7-21 Start Real-time Performance Monitor

2. Select “Start Instance” to start up the performance index, then the status turns into “Started”. Click “Confirm” and the performance real time monitor window appears as shown in Figure3-7-22 below. The data sampling is updated every 3 seconds that along with time processes, the curve slides left.


3-114


Figure3-7-22 Single Window Performance Real-time Monitor

There are two options for performance real-time monitor window, “Monitor” and “Window”. The monitor menu allows the user to lock on specific performance monitoring that once locked, an administrator password is required for further operation. The window menu is applied for designating distribution to real-time performance statistic window where multiple performance indexes can be real-time sampled at a time with overlap layout, referring to Figure3-7-23 below. In order to provide convenience, it is able to pick designated window to top from overlapped windows by opening “Window” menu under “Overlap Window” distribution.


3-115


Figure3-7-23 Overlap Window Performance Real-time Monitor

Horizontal layout is available referring to Figure3-7-24 below:


3-116


Figure3-7-24 Horizontal Layout to Performance Real-time Monitor Windows

Similarly vertical layout is also available referring to Figure3-7-25 below:


3-117


Figure3-7-25 Vertical Layout to Performance Real-time Monitor Windows

Note： Data of real-time sampling is recorded in instance management list rather than being recored in performance statistic. Only the sampling data being instance started can be joined into performance statistic.



Performance Statistic

Select an instance and click [

] button at the instance to open data sampling/report

dialog, referring to Figure3-7-26 below:


3-118


Figure3-7-26 Performance Statistic – Data Gragh

Select the icon of “Data Gragh” and designate particular index to the instance, select time interzone and click “Confirm” button to check on performance sampling detailes of the device in a particular time span. Select the icon of “Data Sheet” to check on the sampling data in the form of data sheet, referring to Figure3-7-27 below:


3-119


Figure3-7-27 Performance Statistic – Data Sheet

Select the icon of “Trend Analysis” to analyze the trends according to sampling record of designated index. The trend is displayed as the form of diagram, referring to Figure3-7-28 below:

Figure3-7-28 Performance Statistic – Trend Analysis


3-120


3.7.2 Interface Performance 3.7.2.1 Universal Interface Resource Management Objective The section introduces configuration of “Universal Interface Resource Management”. Procedure Click “Performance” from top menu and select “Performance Management” from drop down menu, click “Interface Performance” from the left window, the tab column “Universal Interface Resource”, “Universal Interface Template” and “Universal Interface Instance” will appear at the right, referring to Figure3-7-29 below:

Figure3-7-29 Universal Interface Performance Management Page

Select the tab page “Universal Interface Resource” that displays created universal interface resource to query those created information by inputting query conditions such as device name, device IP, interface name and resource ordering. Right click universal interface resource list and select “Import Interface Resource” from the right click menu, the “Import Interface Resource” window appears as shown in Figure3-7-30 below:


3-121


Figure3-7-30 Importing Interface Resource-1

The dialog lists both selected and optional device resources. Select one of the items from optional device resource list and click [

] button to

move one device into selected device resource list. Select all of the devices and press [

] button to move all devices into selected device resource list. Those selected

device resources also can be deleted that by clicking [ and by clicking [

] to remove all selected ones

] to remove single one, and click “Next” to go to second step of

importing interface resource dialog, referring to Figure3-7-31:


3-122


Figure3-7-31 Importing Interface Resource-2

Select device interface resource and click “Done” to save the selected interface. Once the provision is saved, the selected interface resource will be displayed in the universal interface list, referring to Figure3-7-32 below:


3-123


Figure3-7-32 Importing Interface Resource Result

To delete created device resource, select one of them, right click and select “Delete Device Resource” from popped up right click menu. If the instance to this device resource has been created, then the instance will be deleted as well. To delete created interface resource, select one of them, right click and select “Delete Interface Resource” from popped up right click menu. If the instance to this interface resource has been created, then the instance cannot be deleted. 3.7.2.2 Universal Interface Resource Template Objective The section introduces configuration of “Universal Interface Resource Template”. Procedure Select the tab page “Universal Interface Resource” referring to Figure3-7-33 below. The “Universal Interface Resource” displays created universal interface template.


3-124


Figure3-7-33 Universal Interface Resource Template Page

Those created universal device template can be queried by inputting query conditions such as template property, template name, device type, resource type and resource ordering. The system defines a predefined template for each device with different types that the templat covers all interface supported performance indexes of the device type. 

Create customized template:

1. Right click universal device templet list, select “Create New Performance Template” from popped up right click menu and the “Create New Performance Template” dialog is shown as Figure3-7-34:


3-125


Figure3-7-34 Create New Universal Interface Template-1

2. Select device type, input template name (required) and template description (optional) and second step dialog of created new performance template will appear by clicking “Next” button. In this dialog, selected performance resource index and optional performance resource index can be listed that by selecting an optional resource and click [

] button to move the resource into selected

resource list, and by selecting all the resources and click [

] button to move

those resources into selected resource list. The selected resource can also be deleted by clicking [

] for all selected resource removing and by clicking [

] for

single resource removing, referring to Figure3-7-35 below:


3-126



3. The third step dialog of created new performance template will appear by clicking “Next” button. Configurations of index name, index description and default threshold, default sampling interval etc. can be performed to selected performance index according to practical requirement in this dialog, referring to Figure3-7-36 below:


3-127



4. Click “Done” button to save new created template if the configurations are accomplished. Once the save is successful, the created customized template will be displayed in the universal performance template list, referring to Figure3-7-37 below:

Figure3-7-37 Creating New Universal Interface Template Successful


3-128


If the created customized template is required to be modified, select the list row where the template displays and click the [

] button, the “Modify Performance Index”

dialog will be poped up as shown in Figure3-7-38. The modification which has similar procedure with the one when creating allowes the user to add, delete or modify to the property.

Figure3-7-38 Modify Interface Performance Template



Delete created device template

Select a device template that needs to be deleted and right click, select “Delete Device Template” from the right click menu. If instance to the template has been created, then the instance cannot be deleted. 3.7.2.3 Universal Interface Resource Instance Objective The section introduces configuration of “Universal Interface Resource Template”. Procedure 

Universal Interface Instance Query


3-129


Select “Universal Interface Instance” from “Interface Performance” page referring to Figure3-7-29. The “Universal Interface Instance” displays created universal Interface instance, shown as Figure3-7-39:

Figure3-7-39 Universal Interface Performance Instance Page

The information of created universal interface instance can be queried by inputting query conditions such as instance name, status, resource name, template name, sampling/report status and instance order. 

Create Universal Interface Instance

1. Right click an item from universal interface instance list and select “Create New Performance Instance” from the right click menu. The “Create New Performance Instance” dialog will appear as shown in Figure3-7-40 below, one or more device resources can be selected for further configuration.


3-130


Figure3-7-40 Create Universal Interface Performance Instance-1

2. The second step dialog of created new performance instance will appear by clicking “Next” button. Select performance template corresponding with device type in step one from the dialog of second step of created new performance template, referring to Figure3-7-41 below:


3-131



Note： During the creation of device instance, performance index of instance in a same device cannot be duplicated. For example, device 1 creates two device instances, in which instance 1 binds with template 1 while instance 2 binds with template 2, in this cast performance index in template 1 and 2 shall not be duplicated, otherwise a failured prompt window will be popped up during the creation, referring to Figure3-7-42. Additionally, the prompt also appears when the selected device type does not match the template.

Figure3-7-42 Error Prompt in Create New Universal Interface Instance


3-132


3. The third step dialog of created new performance instance will appear by clicking “Next” button, as shown as Figure3-7-43 below. The instance and template can be located then.


4. The forth step dialog of created new performance instance will appear by clicking the above “Next” button. The step is to establish start/stop to the instance. If auto start up is selected, then the starting to selected instance must be established in manual; if timing start up is selected, then the system will implement the starting according to defined time. Similarly, the instance stop obeys the same rule that it has two algorithms as auto start up and timing start up, referring to Figure3-7-44 below:


3-133



5. Click “Complete” button to finish the performance instance creation, referring to Figure3-7-45:

Figure3-7-45 Creating New Universal Interface Instance Successful

Select an item from interface performance instance list and right click, the right click menu appears as shown in Figure3-7-46. Every option in the menu can be seen from the tool bar as well. FiberHome Wview Network Management System User Manual

3-134


Figure3-7-46 Universal Interface Instance List



Delete universal interface instance

Select an interface performance instance item and right click, select “Delete Performance Instance” from the right click menu or click [

] button, and then click

“Confirm” from the confirmation dialog to delete the selected universal interface instance. 

Set index parameter

Select an interface performance instance item and right click, select “Set Index Parameter” from the right click menu or click [

] button, and then modify the

sampling time interval to the instance via the popped up index parameter setting dialog. 

Performance index management

Select an interface performance instance item, press [

] button from the line where

the item being listed to check on performance index contained by the instance. If the selected performance instance is in stopped status, it is capable to re-proviison to the index name, description information, threshold and sampling time. 

Modify sampling&report plan

Select an interface performance instance item, press [


the item being listed to modify the starting/stopping plan of the instance. 

Start instance


3-135


Instance status can be shown from the instance list that the status is divided into “Stopped” and “Started”. If the selected instance is at “Stopped” status, then it can be started by selecting “Start Instance” from right click menu or by selecting [

] button.

Once the instance is started successful, the status would turn into “Started”, referring to Figure3-7-46 below:

Figure3-7-46 Started Interface Performance Instance



Stop instance

If the selected instance is at “Started” status, then it can be stopped by selecting “Stop Instance” from right click menu or by selecting [

] button. Once the instance is

stopped successful, the status would turn into “Stopped”, referring to Figure3-7-47 below:

Figure3-7-47 Stopped Interface Performance Instance



Performance real-time Monitor

Performance real-time monitor is to perform real time monitor to one of the performance indexes of a device or interface with sampling time interval 3 seconds. Select an interface performance instance and press [


the item being listed to check on the performance index contained by the instance. 1. Select a performance index and right click, the popped up window appears as shown in Figure3-7-48 below:


3-136


Figure3-7-48 Start Real-time Performance Monitor

2. Select “Start Instance” to start up the performance index, then the status turns into “Started”. Click “Confirm” and the performance real time monitor window appears. The data sampling is updated every 3 seconds that along with time processes, the curve slides left.

3.8 Configuration Objective The section introduces functional configurations in NM system. Procedure Referring

to

Figure3-8-1,

the

menu

“Configuration”

includes

“Customer

Management”, ”Config FTP Server”, “Config Topology Link”, “Config Topology Node”, “Config

Locking

Interval”,

“Systtem

Configuration”


and

“NE

Configuration 3-137


Management”. The “Configuration” menu is mainly utilized for system functional configurations.

Figure3-8-1 “Configuration” Menu

3.8.1 Customer Management Objective The section introduces configuration of customer management. Procedure Select “Client Management” from drop down menu of “Configuration”, the customer management page is shown as Figure3-8-2 below:

Figure3-8-2 Customer Management Page


3-138


Referring to figure above, there are sub-menus as “Customer Management” and “Customer Service Management” from the tree structure of “Contact Management” at left. All contact information will be shown at right column and they can be created, modified and deleted via right click menu. The creation of contact information is as shown as Figure3-8-3 below:

Figure3-8-3 Creating Customer Information

3.8.2 FTP Server Configuration Objective The section introduces configuration of FTP server. Procedure Select “Config FTP Server” from drop down menu of “Configuration”, the FTP server configuration page is shown as Figure3-8-4 below:


3-139


Figure3-8-4 FTP Server Configuration Page

3.8.3 Config Topology Link Objective The section introduces configuration of FTP server. Procedure Select “Config Topology Link” from drop down menu of “Configuration”, the linetype creating, modifying and deleting can be provisioned in the dialog shown in Figure3-8-5 below, where 10 customized lintypes are provided to the user. For linetypes that defined by the system or being already applied in topolofy grapgh, they cannot be deleted by the user.


3-140


Figure3-8-5 Topology Linetype Configuration

3.8.4 Config Topology Node Objective The section introduces configuration of topology node. Procedure Select “Config Topology Node” from drop down menu of “Configuration”, the topology node configuration dislog is shown as Figure3-8-6 below. Colors indicating different node status can be provisioned as well as node information located in the topology viewgragh. Those configurations can be saved by clicking “Confirm” button.


3-141


Figure3-8-6 Topology Node Configuration

3.8.5 Config Locking Interval Objective The section introduces configuration of locking interval. Procedure Select “Config Locking Interval” from drop down menu of “Configuration”, the lockinginterval configuration dialog is shown as Figure3-8-7 below. System locking time can be provisioned wthin the page that by clicking “Confirm” the user is able to save the configuration.


3-142


Figure3-8-7 Locking Interval Configuration

3.8.6 System Configuration Objective The section introduces system configuration. Procedure Select “System Configuration” from drop down menu of “Configuration”, the system configuration tab page including “System Service” and “Timing Task” is shown as Figure3-8-8 below. The “System Service” is set as default page.

Figure3-8-8 System Configuration


3-143


3.8.6.1 System Service Configuration Objective The section introduces configuration of system service. Procedure The “System Service” has 10 types of service including “Device Polling Queue 1”, “Device Polling Queue 2”, “Device Polling Queue 3”, “Device Polling Queue 4”, “Harddisk Space Check”, “Mail Service”, “Text Message Service”, “Trap Forwarding Service”, “Trap Synchronization Service” and “Performance Log Backup by Capacity”. Right click menu to each of those services is shown as Figure3-8-9 below:

Figure3-8-9 System Service Right Click Menu

Referring to above figure, the “Start” and “Stop” are for starting/stopping designated system service, the “Refresh” is for refreshing service list while the “Config” is for access of designated service configuration page. 

Device polling queue

1. Click “Config” from right click menu when the designated system service is one of the following: “Device Polling Queue 1”, “Device Polling Queue 2”, “Device Polling Queue 3” and “Device Polling Queue 4”, the configuration dialog of device polling queue service is shown as Figure 3-8-10 below. The tab page “Service Parameter Config” is set as default page.


3-144


Figure3-8-10 Device Polling Queue Service Configuration

2. Click “Device Polling Queue #” from the left tab, the device polling queue tab page will be shown to the right, referring to Figure3-8-11 below:

Figure3-8-11 Queue Configuration

3. Polling interval and polling device within the queue can be modified in the page. FiberHome Wview Network Management System User Manual

3-145


Every device in the device list is acquiescently arranged into queue 4. Device will also be added into the queue 4 by clicking to empty the queue that the device locates. Select a queue and click “Modify Queue”, the dialog will be shown as Figure3-8-12 below:

Note： Maximum 10 devices for Queue 1, 20 for Queue 2, 200 for Queue 3 while no maximum number limit for Queue 4.

Figure3-8-12 Device Selecting

4. Select or fill in proper conditions referring to above figure and click “Next”, the device list will appear shown as Figure3-8-13 below:


3-146


Figure3-8-13 Device List



Harddisk space check

1. The dialog of harddisk space check is shown as Figure3-8-14 below. The tab page “Service Parameter Configuration” is set as default page.

Figure3-8-14 Harddisk Space Check Service Configuration


3-147


2. Click “Harddisk Space Check” from the left tab, the tab page appears to the right as shown in Figure3-8-15 below:

Figure3-8-15 Harddisk Space Check Configuration

3. Select or fill in proper conditions referring to above figure and click “Confirm” to save the config. 

Mail service

1. If the designated system service is “Mail Service”, the mail service dialog is shown as Figure3-8-16 below. The tab page “Service Parameter Configuration” is set as default page.


3-148


Figure3-8-16 Mail Service Configuration

2. Click the tab “Mail Service” from left tab and the mail service tab page is shown to the right, referring to Figure3-8-17 below:

Figure3-8-17 Mailbox Configuration


3-149



Text message service

1. If the designated system service is “Text Message Service”, the text message service dialog is shown as Figure3-8-18 below. The tab page “Service Parameter Configuration” is set as default page.

Figure3-8-18 Text Message Service Configuration

2. Click “Text Message Service” from left tab and the text message service tab page is shown to the right, referring to Figure3-8-19 below:


3-150


Figure3-8-19 Text Message Configuration

3. Select or fill in proper conditions referring to above figure and click “Confirm” to save the config.

Note： The text message service needs to be customized developed and utilized along with plug-in unit of text message service.



Trap forwarding service

1. If designated system service is “Trap Forwarding Service”, the trap forwarding service dialog is shown as Figure3-8-20 below. The tab page “Service Parameter Configuration” is set as default page.


3-151


Figure3-8-20 Trap Forwarding Service Configuration

2. Click “Trap Forwarding Service” from left tab and the trap forwarding service tab page is shown to the right, referring to Figure3-8-21 below:

Figure3-8-21 Trap Forwarding Configuration


3-152



Trap synchronization service

1. If designated service is “Trap Synchronization Service”, the trap synchronization service dialog is shown as Figure3-8-22 below. The tab page “Service Parameter Configuration” is set as default page.

Figure3-8-22 Trap Synchronization Service Configuration

2. Click “Trap Synchronization Service” from left tab and the trap synchronization service tab page is shown to the right, referring to Figure3-8-23 below:


3-153


Figure3-8-23Trap Synchronization Configuration


Note： The function of trap synchronization service requires equipment support.



Performance log backup by capacity

1. If designated service is “Performance Log Backup by Capacity”, the performance log backup by capacity dialog is shown as Figure3-8-24 below. The tab page “Service Parameter Configuration” is set as default page.


3-154


Figure3-8-24 Performance Log Backup by Capacity Configuration Page

2. Click “Performance Log Backup by Capacity” from left tab and the performance log backup by capacity tab page is shown to the right, referring to Figure3-8-25 below:

Figure3-8-25 Performance Log Backup by Capacity Configuration FiberHome Wview Network Management System User Manual

3-155


3. Select or fill in proper conditions referring to above figure and click “Confirm” to save the config. 3.8.6.2 Timing Task Configuration Objective The section introduces configuration of timing task. Procedure The “Timing Task” has 5 types of task including “Trap Log Backup”, “Security Log Backup”, “Operation Log Backup”, “Event Log Backup” and “Performance Log Backup by Validity”. Right click menu to each of those services is shown as Figure3-8-26 below:

Figure3-8-26Timing Task Right Click Menu

Referring to above figure, the “Start” and “Stop” are for starting/stopping designated timing task, the “Refresh” is for refreshing service list while the “Config” is for access of designated task configuration page. 

Trap log backup

1. If designated task is “Trap Log Backup”, the trap log backup is shown as Figure3-8-27 below. The tab page “Task Parameter Configuration” is set as default page.


3-156


Figure3-8-27 Trap Log Backup Task Configuration

2. Click “Trap Log Backup” from left tab and the trap log backup tab page is shown to the right, referring to Figure3-8-28 below:


3-157


Figure3-8-28 Trap Log Backup Configuration


Security log backup

1. If designated task is “Security Log Backup”, the security log backup is shown as Figure3-8-29 below. The tab page “Task Parameter Configuration” is set as default page.


3-158


Figure3-8-29 Security Log Backup Task Configuration

2. Click “Security Log Backup” from left tab and the security log backup tab page is shown to the right, referring to Figure3-8-30 below:


3-159


Figure3-8-30 Security Log Backup Configuration


Operation log backup

1. If designated task is “Operation Log Backup”, the operation log backup is shown as Figure3-8-31 below. The tab page “Task Parameter Configuration” is set as default page.


3-160


Figure3-8-31 Operation Log Backup Task Configuration

2. Click “Operation Log Backup” from left tab and the operation log backup tab page is shown to the right, referring to Figure3-8-32 below:


3-161


Figure3-8-32 Operation Log Backup Configuration


Event log backup

1. If designated task is “Event Log Backup”, the event log backup is shown as Figure3-8-33 below. The tab page “Task Parameter Configuration” is set as default page.


3-162


Figure3-8-33 Event Log Backup Task Configuration

2. Click “Event Log Backup” from left tab and the event log backup tab page is shown to the right, referring to Figure3-8-34 below:


3-163


Figure3-8-34 Event Log Backup Configuration


Performance log backup by validity

1. If designated task is “Performance Log Backup by Validity”, the performance log backup by validity is shown as Figure3-8-35 below. The tab page “Task Parameter Configuration” is set as default page.


3-164


Figure3-8-35 Performance Log Backup by Validity Task Configuration

2. Click “Performance Log Backup by Validity” from left tab and the performance log backup by validity tab page is shown to the right, referring to Figure3-8-36 below:


3-165


Figure3-8-36 Performance Log Backup by Validity Configuration


3.9 Tool Objective The section introduces contents and funcationalities in “Tool” menu. Procedure The “Tool” menu has 4 types of tool including “Ping”, “Telent”, “MIB Tool” and “File Export and Conversion”, referring to Figure3-9-1 below:


3-166


Figure3-9-1 “Tool” Menu

3.9.1 Ping Objective The section introduces the configuration of “Ping”. Procedure Select “Ping” from the “Tool” menu referring to Figure3-9-1, the ping window appears as shown in Figure3-9-2 below. Input ping command plus destination address and press “Enter”, the result appears as shown in Figure3-9-3.

Figure3-9-2 Ping Window


3-167


Figure3-9-3 Ping Result

3.9.2 Telnet Objective The section introduces the configuration of “Telnet”. Procedure Select “Telnet” from the “Tool” menu referring to Figure3-9-1, the Telnet window appears as shown in Figure3-9-4 below. Input Telnet command plus destination address and the result appears as shown in Figure3-9-5, remote access to device can be available by inputting username and password.


3-168


Figure3-9-4 Telnet

Figure3-9-5 Telnet Result

3.9.3 MIB Tool Objective The section introduces the configuration of “MIB Tool”. Procedure 1. Select “MIB Tool” from the “Tool” menu referring to Figure3-9-1, the MIB tool window appears as shown in Figure3-9-6 below.


3-169


Figure3-9-6 MIB Tool

2. Select or fill in proper MIB information referring to above figure and click “Confirm” to confirm the preset, results will be read and shown at the right column.

3.9.4 File Export and Conversion Objective The section introduces the configuration of “MIB Tool”. Procedure 1. Select “File Export and Conversion” from the “Tool” menu referring to Figure3-9-1, the file export and conversion window appears as shown in Figure3-9-7 below.


3-170


Figure3-9-7 File Export and Convert

2. Click the first “Browse” button referring to above figure, the topology file (dev file) selection window appears as shown in Figure3-9-8 below:

Figure3-9-8 Selecting Converting File


3-171


3. Click the second “Browse” button referring to Figure3-9-7, the generating file (xml file) selection window appears as shown in Figure3-9-9 below:

Figure3-9-9 Path of Generating XML Topology File

4. Click “Start Converting” button to convert the exported file.

3.10 Report Objective The section introduces the functionalities of report generating to trap information and device information. Procedure The F-Engine Wview NM system currently provides report generating to trap information and device information, which has 4 types of report or facility including “Trap Report”, “Device Report”, “Port Utilization Ratio” and “Performance Report”, referring to Figure3-10-1 below. Each of those report type contains varieties of statistics or analyzing reports.


3-172


Figure3-10-1 “Report” Menu

3.10.1 Trap Report Objective The section introduces the configuration of “Trap Report”. Procedure Select “Trap Report” from the “Report” menu referring to Figure3-10-1, the trap report window appears as shown in Figure3-10-2 below. The trap report tab page includes “Trap Record Initial Detailed Report”, “Trap Record Statistic Report” and “Trap Monthly Trend Analysis Report”.

Figure3-10-2 Trap Report Page

3.10.2 Device Report Objective The section introduces the configuration of “Device Report”. Procedure


3-173


Select “Device Report” from the “Report” menu referring to Figure3-10-1, the device report window appears as shown in Figure3-10-3 below. The device report tab page includes “Device Resource Record Report” and “Device Resource Statisitc & Analysis Report”.

Figure3-10-3 Device Report Page

3.10.3 Report Generating Objective The section introduces the configuration of “Report Generating”. Procedure The system report provides two generating methods including real-time generating and periodically generating, in which the real-time report indicates the immediately generating way once the port export button being clicked that the generating time cost is depending on data quantity and analysis complexity, while the period report indicates a time defined generating way that the user is able to designate as precisely as a certain time spot every day/week/month. It is noticed that the period report cannot be fetched from designated report generating path if the period report is generated but the client terminal is not started. However,

the

generated

report

can

be

found

under

the

path

“..\jboss*\server\Wview\ftpserver\home\Wview\report” of server installation category in the host that the server locates, referring to Figure3-10-6 below: FiberHome Wview Network Management System User Manual

3-174


Figure3-10-6 Report Generating Time Provision

3.11 Service Objective The section introduces contents and funcationalities of service management module. Procedure The facility “Service” is designed to provide conveniences for users that to shift concentration from concerning of device to service consideration. The service module includes

“Service

Management”,

“Service

Type

Management”,

“Customer

Management”, “Contact Management”, “Region Management” and “Service Trap Management”, referring to Figure3-11-1 below:


3-175


Figure3-11-1 “Service” Menu

3.11.1 Service Type Management Objective The section introduces the configuration of “Service Type Management”. Procedure Select “Service Type Management” from the “Service” menu referring to Figure3-11-1, the service type management window appears as shown in Figure3-11-14 below.

Figure3-11-14 Service Type Management Page

The service type management allows the user to create, modify and delete service type. The dialog of creation to service type is shown as Figure3-11-15 below:


3-176


Figure3-11-15 Create Service Type

Select or fill in proper information referring to above figure and click “Done” button to finish the creating.

3.11.2 Customer Management Objective The section introduces the configuration of “Customer Management”. Procedure Select “Customer Management” from the “Service” menu referring to Figure3-11-1, the customer management window appears as shown in Figure3-11-16 below.


3-177


Figure3-11-16 Customer Management Page

The customer management allows the user to create, modify and delete the customer information. The dialog of creation to customer information is shown as Figure3-11-17 below:

Figure3-11-17 Create Customer Information


3.11.3 Contact Management Objective FiberHome Wview Network Management System User Manual

3-178


The section introduces the configuration of “Contact Management”. Procedure Select “Contact Management” from the “Service” menu referring to Figure3-11-1, the contact management window appears as shown in Figure3-11-18 below.

Figure3-11-18 Contact Management Page

The contact management allows the user to create, modify and delete the contact information. The dialog of creation to contact information is shown as Figure3-11-19 below:

Figure3-11-19 Create Contact Information


3-179



3.11.4 Region Management Objective The section introduces the configuration of “Region Management”. Procedure Select “Region Management” from the “Service” menu referring to Figure3-11-1, the region management window appears as shown in Figure3-11-20 below.

Figure3-11-20 Region Management Page

The region management allows the user to create, modify and delete the region information. The dialog of creation to region information is shown as Figure3-11-21 below:


3-180


Figure3-11-21 Create Region Information


3.11.5 Service Trap Management Objective The section introduces the configuration of “Service Trap Management”. Procedure Select “Service Trap Management” from the “Service” menu referring to Figure3-11-1, the service trap management window appears as shown in Figure3-11-22 below.


3-181


Figure3-11-22 Service Trap Management Page

The service trap management allows the user to query and delete relative service trap information.

3.12 Help Objective The section introduces contents and funcationalities of “Help” menu. Procedure The “Help” menu has 2 types of help items including “Help Theme” and “ABOUT Information”, referring to Figure3-12-1 below:

Figure3-12-1 “Help” Menu

3.12.1 Help Theme Objective The section introduces the information of “Help Theme”. Procedure


3-182


Select “Help Theme” from the “Help” menu referring to Figure3-12-1, the help theme window appears as shown in Figure3-12-2 below. The help information is displayed as CHM format.

Figure3-12-2 Help Information

3.12.2 About Information Objective The section introduces the information of “ABOUT Information”. Procedure Select “ABOUT Information” from the “Help” menu referring to Figure3-12-1, the ABOUT information window appears as shown in Figure3-12-3 below.


3-183


Figure3-12-3 About Information


3-184


Chapter4 Network Element Management Module Introduction 4.1 Overview This system is plug-in system. User can choose needed network element management module according to the ordered product. This chapter mainly introduces the name of all kinds of device and the legend of all devices in every state. This chapter includes the following topics: Content

Page

4.1 Overview

4-1

4.2 Device Legend Introduction

4-1

4.2 Device Legend Introduction The Wivew Network Management System of our company supports network element management module such as B2112,C15100,R3011,R4001,R4101,R4202,R4004, OL200,S3101, AM1001,S2000,R8000,M8000,S3512MP,S3528,S3552 and etc.

Table 4-1 Device Legend Introduction Device Name

Device State Non-connective

Connective Not Opening

Not Opening

Opening

Opening

Configuration

Configuration

Configuration

Configuration

Program

Program and

Program

Program and

Having Fault

Having Fault

B2112 C15100

R3011 R4001


4-1

Chapter4 Network Element Management Module Introduction Device Name

Device State Non-connective

Connective Not Opening

Not Opening

Opening

Opening

Configuration

Configuration

Configuration

Configuration

Program

Program and

Program

Program and

Having Fault

Having Fault

R4101

R4202

R4004

OL200 S3101

AM1001 S2000 R8000

M8000

S3528 SubVie

-

-

-

w


4-2

FiberHome+Wview+Network+Management+System+User+Manual

Recommend Documents